GAL AXY EL ECT RICAL
FEATURES
Silicon planar power zener diodes
For use in stabilizing and clipping curcuits with high
power rating.
Standard zener voltage tolerance is ±10%. Add
MECHANICAL DATA
Case:DO-27
Terminals: solderable per MIL-STD-202, method 208
Polarity: cathode Band
Marking: type number
Approx. weight: 1.15 grams.
(2) 8.3ms single half sine-wav e, or equiv alent square wav e, duty cy cle=4 pulses per minute maximum.
Zener current (see Table "Characteristics")
Storage temperature range Ts -55---+150
Peak f orw ard surge current 8.3ms single half sine-w ave superimposed on rated
load (JEDEC Method)(NOTE 1,2) IFSM see fig.5
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTIC S
NOTES: (1) Mounted on 8.0mm2 copper pads to each terminal.
Junction temperature TJ -55---+150
A
DC pow er dissipation @ TL=75, measure at zero lead length (Fig.1)
derate above 75 (NOTE 1) PD
5.0
40.0
W
mW
1N5333B - - - 1N5388B
suffix "B" for ±5% tolerance. other zener voltage
ZENER DIODES
and tolerances are available upon request.
POWER DISSIPATION: 5 .0 W
DO - 27
Ratings at 25 ambient temperature unless otherwise specified.
Single phase,half wave,60 Hz,resistive or inductive load. For capacitive load,derate by 20%.
UNITVALUESYMBOL
BLGALAXY ELECTRICAL
Document Number 0284007
1.
www.galaxycn.com
BL
ELECTRICAL CHARACTERISTICS (TA=25)
IRVR
µAV
1N5333B 3.3 380 3.0 400 300 1.0 20 0.85 1440
1N5334B 3.6 350 2.5 500 150 1.0 18.7 0.80 1320
1N5335B 3.9 320 2.0 500 50 1.0 17.6 0.54 1220
1N5336B 4.3 290 2.0 500 10 1.0 16.4 0.49 1100
1N5337B 4.7 260 2.0 450 5.0 1.0 15.3 0.44 1010
1N5338B 5.1 240 1.5 400 1.0 1.0 14.4 0.39 930
1N5339B 5.6 220 1.0 400 1.0 2.0 13.4 0.25 865
1N5340B 6.0 200 1.0 300 1.0 3.0 12.7 0.19 790
1N5341B 6.2 200 1.0 200 1.0 3.0 12.4 0.10 765
1N5342B 6.8 175 1.0 200 10 5.2 11.5 0.15 700
1N5343B 7.5 175 1.5 200 10 5.7 10.7 0.15 630
1N5344B 8.2 150 1.5 200 10 6.2 10.0 0.20 580
1N5345B 8.7 150 2.0 200 10 6.6 9.5 0.20 545
1N5346B 9.1 150 2.0 150 7.5 6.9 9.2 0.22 520
1N5347B 10 125 2.0 125 5.0 7.6 8.6 0.22 475
1N5348B 11 125 2.5 125 5.0 8.4 8.0 0.25 430
1N5349B 12 100 2.5 125 2.0 9.1 7.5 0.25 395
1N5350B 13 100 2.5 100 1.0 9.9 7.0 0.25 365
1N5351B 14 100 2.5 75 1.0 10.6 6.7 0.25 340
1N5352B 15 75 2.5 75 1.0 11.5 6.3 0.25 315
1N5353B 16 75 2.5 75 1.0 12.2 6.0 0.30 295
1N5354B 17 70 2.5 75 0.5 12.9 5.8 0.35 280
1N5355B 18 65 2.5 75 0.5 13.7 5.5 0.40 264
1N5356B 19 65 3.0 75 0.5 14.4 5.3 0.40 250
1N5357B 20 65 3.0 75 0.5 15.2 5.1 0.40 237
1N5358B 22 50 3.5 75 0.5 16.7 4.7 0.45 216
1N5359B 24 50 3.5 100 0.5 18.2 4.4 0.55 198
1N5360B 25 50 4.0 110 0.5 19.0 4.3 0.55 190
1N5361B 27 50 5.0 120 0.5 20.6 4.1 0.60 176
1N5362B 28 50 6.0 130 0.5 21.2 3.9 0.60 170
1N5363B 30 40 8.0 140 0.5 22.8 3.7 0.60 158
1N5364B 33 40 10 150 0.5 25.1 3.5 0.60 144
1N5365B 36 30 11 160 0.5 27.4 3.5 0.65 132
1N5366B 39 30 14 170 0.5 29.7 3.1 0.65 122
1N5367B 43 30 20 190 0.5 32.7 2.8 0.70 110
1N5368B 47 25 25 210 0.5 35.8 2.7 0.80 100
1N5369B 51 25 27 230 0.5 38.8 2.5 0.90 93
1N5370B 56 20 35 280 0.5 42.6 2.3 1.00 86
1N5371B 60 20 40 350 0.5 45.5 2.2 1.20 79
1N5372B 62 20 42 400 0.5 47.1 2.1 1.35 76
IZT
mA
Zener voltage
(Note 2)
Max Reverse Leakage
Current IR
(Note 3)
A
VZ
(Note 4)
V
IZM
(Note 5)
mA
ZZT@IZK =1µA
Type
(Note 1)
Maximum Zener
Impedance
(Note 2)
ZZT@IZT
VZ@IZT
V
www.galaxycn.com
Document Number 0284007 2.
BLGALAXY ELECTRICAL
ELECTRICAL CHARACTERISTICS (TA=25)
IRVR
µAV
1N5373B 68 20 44 500 0.5 51.7 2.0 1.5 70
1N5374B 75 20 45 620 0.5 56.0 1.9 1.6 63
1N5375B 82 15 65 720 0.5 62.2 1.8 1.8 58
1N5376B 87 15 75 760 0.5 66.0 1.7 2.0 54.5
1N5377B 91 15 75 760 0.5 69.2 1.6 2.2 52.5
1N5378B 100 12 90 800 0.5 76.0 1.5 2.5 47.5
1N5379B 110 12 125 1000 0.5 83.6 1.4 2.5 43.0
1N5380B 120 10 170 1150 0.5 91.2 1.3 2.5 39.5
1N5381B 130 10 190 1250 0.5 98.8 1.2 2.5 36.6
1N5382B 140 8.0 230 1500 0.5 106 1.2 2.5 34.0
1N5383B 150 8.0 330 1500 0.5 114 1.1 3.0 31.6
1N5384B 160 8.0 350 1650 0.5 122 1.1 3.0 29.4
1N5385B 170 8.0 380 1750 0.5 129 1.0 3.0 28.0
1N5386B 180 5.0 430 1750 0.5 137 1.0 4.0 26.4
1N5387B 190 5.0 450 1850 0.5 144 0.9 5.0 25.0
1N5388B 200 5.0 480 1850 0.5 152 0.9 5.0 23.6
NOTE:
1.TOLERANCE AND VOLTAGE DESIGNATION-The JEDEC type numbers shown indicate a tolerance of ±10% with guaranteed limits on only Vz, IR, Ir, and
VF as shown in the electrical characteristics table. Units with guaranteed limits on all seven parameters are indicated by suffix "B" for ±5% tolerance.
2.ZENER VOLTAGE (Vz) AND IMPEDANCE (ZZT & ZZK) - Test conditions for zener voltage and impedance are as follows;Iz is applied 40±10ms prior to
reading. Mounting contacts are located from the inside edge of mounting clips to the body of the diode.
3.SURGE CURRENT (Ir) - Surge current is specified as the maximum allowable peak, non-recurrent square-wave current with a pulse width, PW, of 8.3ms.
The data given in Fig 5. May be used to find the maximum surge current for a quare wave of any pulse width between 1 ms by plotting the applicable
points on logarithmic paper. Examples of this, using the 6.8v and 200v zeners, are shown in Fig 6. Mounting contact located as specified in NOTE 3.
4.VOLTAGE REGULATION (Vz) - Test conditions for voltage regulation are as follows: Vz measurements are the made at 10% and then at 50% of the Iz max
value listed in the electrical characteristics table. The test currents are the same for the 5% and 10% tolerance devices. The test current time druation for
each Vz measurement is 40±10ms.Mounting contact located as specified in NOTE 2.
5.MAXIMUM REGULATOR CURRENT (I
ZM) - The maximum current shown is based on the maximum voltage of a 5% type unit. Therefore, it applies only to
the B-suffix device. The actual IZM for any device may not exceed the value of 5 watts divided by the actual Vzof the device. T
L=75 at 3/8" maximum from
the device body.
ZZT@IZK =1µA
Type
(Note 1)
Maximum Zener
Impedance
(Note 2)
ZZT@IZT
Zener voltage
(Note 2)
VZ@IZT
V
IZT
mA
Max Reverse Leakage
Current IR
(Note 3)
A
VZ
(Note 4)
V
IZM
(Note 5)
mA
BLGALAXY ELECTRICAL
Document Number 0284007 3.
www.galaxycn.com
2
10
.2
.001 .01 5.1 20 100.5
5
20
.5
1
50101.005 .05
D=0
D=0.01
D=0.05
D=0.1
D=0.2
D=0.5
AVERAGE FORWARD CURRENT
AMPERES
θVz TEMPERATURE COEFFICIENT
(mv)C
J@IZT
RESISTANCE /W)
PEAK FORWARD SURGE CURRENT
AMPERES
JUNCTION-TO-LEAD /W
F IG.1 - -FO RWARD DERATING CURVE
NUMBER OF CYCLES AT 60 Hz
FIG.2 -- TEM PERATURE COEFF ICIENT RANG E
F IG.3 - - TYPICAL THERM AL RESIS TANCE FIG.4 -- MAXIMUM NO N-REP ETIT IVE SURGE CURRENT
L/LEAD LENGTH TO HEAT SINK(INCH)
RATINGS AND CHARACTERISTIC CURVES 1N5333B - - - 1N5388B
AMBIENT TEMPERATURE, Vz,ZENER VOLTACE @IZT(VOLTS)
TIME SECONDS
FIG.5 -- TYPICAL T HERMAL RESPONSE
ΘJL.JUNCTION-TO-LEAD THERMAL RESIST
A
ΘJl(1.D)TRANSIENT THERMAL RESISTANCE
40
.1
28 40
1
10
4 5 10 20 30 60 80 100 200
.2
.4
2
4
20
30
10
20
0
0.2 .4
40
.6 .8 1
200
100
50
10
20
5
0 20 16040 80 120 200
300
60 100 140 180 220 240
RANGE
8
2
6
0
020 6040 100 120 14080 160 180 200
4
L-LEAD LENGTH
TO HEAT SINK
BLGALAXY ELECTRICAL
Document Number 0284007
4.
www.galaxycn.com
BLGALAXY ELECTRICAL
www.galaxycn.com
Document Number 0284007
5.
Iz,ZENER CURRENT(mA)
Iz,ZENER CURRENT(mA)
RATINGS AND CHARACTERISTIC CURVES 1N5333B - - - 1N5388B
PW, PULSE WIDTH(ms) Vz , ZENER VOLTAGE(VOLTS)
Iz,ZENER CURRENT(mA) Ir.PEAK SURGE CURRENT(AMPS)
FIG.6 -- PEAK SURGE CURRENT VERSUS PULSE WIDTH
Vz,ZENER VOLTAGE(VOLTS)
FIG.7 -- ZE NER VOLTAGE VERSUS ZENE R CURRENT
Vz=6.8 THRU 10 VOLTS
FIG.8 -- ZE NER VOLTAGE VERSUS ZENER CURRENT
Vz=11 THRU 75 VOLTS FIG.9 -- ZE NER VOLTAGE VERSUS ZENER CURRENT
Vz=82 THRU 200 VOLTS
Vz,ZENER VOLTAGE(VOLTS)
.1
110 1000100
.2
.5
1
20
10
5
2
30
VZ=6.8V
VZ=200V
100
1
10
.1 12 4310
1000
57689
T=25
Tc=25
100
1
10
.110 20 4030
1000
50 7060 80
T=25
100
1
10
.1
80 100 140120
1000
160 200180 220