Keysight Technologies Infiniium Oscilloscope Probes and Accessories Data Sheet To get the most out of your Infiniium oscilloscope, you need the right probes and accessories for your particular applications. Whether you need the high bandwidth and low loading of an active probe, an easy way to connect to surface mount ICs, or a passive probe to measure high voltages, there's a wide selection of high-quality probes and accessories for your Infiniium oscilloscope. Table of Contents Probe Compatibility Table............................................................................... 3 InfiniiMax Active Probe System Overview....................................................... 4 InfiniiMax III/III+ probing system................................................................ 6 InfiniiMax II probing system..................................................................... 14 InfiniiMax I probing system...................................................................... 21 Active Termination Adapter........................................................................... 25 InfiniiMode Active Probes ............................................................................. 27 N2750A/51A/52A InfiniiMode probes .....................................................27 Single-Ended Active Probes ......................................................................... 30 N2795A/96A/97A active probes.............................................................. 30 N7020A power rail probe......................................................................... 32 General Purpose Differential Active Probes ................................................. 34 N2790A/91A/891A high-voltage differential probes.............................. 34 N2804/05A high voltage differential probes........................................... 35 1153A/41A low-noise differential probes................................................ 36 N2818A/19A general-purpose differential probes.................................. 37 AC/DC Current Probes.................................................................................. 38 1146B low-cost AC/DC current probe..................................................... 38 1147B/N2893A AC/DC current probe .................................................... 39 N2780B/81B/82B/83B/83L AC/DC current probes............................... 40 High-Sensitivity Current Probes.................................................................. 41 General Purpose Passive Probes................................................................... 43 N2870A-76A passive probes.................................................................... 43 1165A passive probe................................................................................ 46 54006A high bandwidth passive probe................................................... 48 High Voltage Passive Probes......................................................................... 49 10076C 100:1 passive probe.................................................................... 49 N2771B 1000:1 passive probe................................................................. 50 Mixed Signal Oscilloscope Logic Probes and Accessories........................... 51 Probing Accessories...................................................................................... 53 InfiniiMax probe accessories.................................................................... 53 N2744A T2A probe interface adapter...................................................... 54 N2784A/85A/86A/87A probe positioners............................................... 54 Wedge probe adapters............................................................................. 56 Fine pitch and PC board accessories....................................................... 57 E2697A high impedance adapter............................................................ 57 Related Literature.......................................................................................... 58 03 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet Probe Compatibility Table For ordering information when replacing your probe or probe accessory: Refer directly to the page number listed in the table of contents for your probe model. To assist you in selecting the proper probe for your application: Use our probe compatibility table below to find the probes that are recommended for use with your Infiniium scope. Or refer to our probe overview page at the beginning of each section in the table of contents explaining what the different probe types are and the models available for your Infiniium. 9000 Series S-Series 90000/90008A Series* V-Series, 90000X/Q, Z-Series Scope bandwidth 600 MHz - 4 GHz 500 MHz - 8 GHz 2.5 GHz - 13 GHz 8 GHz - 33 GHz (V-Series) 13 GHz - 33 GHz (90000X) 16 GHz - 63 GHz (90000Q) 20 GHz - 63 GHz (90000Z) Probe interfac AutoProbe AutoProbe AutoProbe AutoProbe II Standard probe N2873A N2873A InfiniiMax active probing system, page 5 1130A/31A/32A N2830A/31A/32A, 1130A/31A/32A/34A, 1168A/69A N2830A/31A/32A, 1131A/32A/34A, 1168A/69A N2800A/81A/82A/83A, N7000A/71A/72A/73A Active termination adapter, page 25 -- -- -- N7010A (except for 90000X) InfiniiMode active probes, page 26 N2750A/51A/52A N2750A/51A/52A N2750A/51A /52A N2750A/51A/52A with N5442A Single-ended active probes, page 29 N2795A/96A/97A, N7020A N2795A/96A/97A, N7020A N2795A/96A/97A N2795A/96A/97A with N5442A General purpose differential active probes, page 32 N2790A/91A, N2818A/19A, 1141A, N2804A/05A N2790A/91A, N2818A/19A, 1141A, N2804A/05A N2791A/N2891A with E2697A, 1141A, N2818A/19A /04A/05A N2790A/91A/891A with N5449A, N2818A/19A/04A/05A with N5442A Current probes, page 35 1146B/47B, N2780B/ 81B/82B/83B/N2893A, N2820A/21A 1146B/47B, N2780B/81B/82B/83B/ N2893A, N2820A/21A 1146B, N2780B/ 81B/82B/83B with E2697A 1147B, N2893A with N5449A General purpose passive probes, page 40 N2870A-76A, 10073D, 10070D, 1165A N2870A-76A, 10073D, 10070D, 1165A N2870A-76A, 10073D, 10070D, 1165A with E2697A N2873A with N5449A (N5449A includes one N2873A) High voltage passive probes, page 46 10076C, N2771B 10076C, N2771B 10076C, N2771B with E2697A 10076C, N2771B with N5449A * The 1147B, N2790A and N2893A are not compatible with 80000, 90000 and 90008 Series scopes. 04 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet InfiniiMax Active Probe System Overview The InfiniiMax probing system offers you the highest performance available for measuring differential and single-ended signals, with flexible connectivity solutions for today's high-density ICs and circuit boards. Keysight Technologies, Inc. pioneered "probe head" type probes starting with the InfiniiMax I probe system in 2003. InfiniiMax I boasted a 7 GHz bandwidth and provided both differential and single-ended probe heads to fit multiple use models. The "probe head" topology allows higher performance. It allows more flexibility in the use models accommodating browser, solder-in, SMA etc. In 2005 Keysight released InfiniiMax II 1168A/69A Series. This continued the probe head style probe topology while boosting the bandwidth to 13 GHz. The technology used for InfiniiMax II is the same as the one for InfiniiMax I except for the use of a new 70 GHz SiGe bipolar IC process. InfiniiMax II set new standards for performance, low noise, and low loading. While the 13 GHz bandwidth of the InfiniiMax II probe system is still very adequate for many measurement needs, the extreme speeds of emerging serial data and communication technologies has driven the need for even higher performance levels. To respond to this need, Keysight has developed the InfiniiMax III 30 GHz probing system. A wide range of probe heads allows connection using a browser, ZIF (zero insertion force) tip, 2.92-mm or 3.5-mm SMA cable, or solder-in tips. The new InfiniiMax III+ probe system is greatly expanding the measurement capability and usability of probes capable of measuring all the components of a differential signal. With a single connection, InfiniiMax III+ can be set to measure the differential or single-ended A or B, or the common mode component of a differential signal. InfiniiMax I 1130A-34A InfiniiMax II 1168A/69A InfiniiMax III N2800A-03A InfiniiMax III+ N2830A-32A InfiniiMax III+ N7000A-03A Probe interface AutoProbe I AutoProbe I AutoProbe II AutoProbe I AutoProbe II 1.5 GHz 1130A (D, SE) 3.5 GHz 1131A (D, SE) 4 GHz N2830A (IM) 5 GHz 1132A (D, SE) 7 GHz 1134A (D, SE) 8 GHz 10 GHz 1168A (D, SE) 13 GHz 1169A (D, SE) N2831A (IM) N7000A (IM) N2832A (IM) N7001A (IM) 16 GHz N2800A (D, SE) N7002A (IM) 20 GHz N2801A (D, SE) N7003A (IM) 25 GHz N2802A (D, SE) 30 GHz N2803A (D, SE) D: Differential, SE: Single-ended, IM: InfiniiMode 05 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet Modern high speed digital applications have pushed the limit of high bandwidth and high performance probing solutions. Keysight offers four different InfiniiMax probe families to meet today's challenging high speed measurement needs -- InfiniiMax I/II/III/III+. Each of these solutions has its own, unique value. The principle difference is found in the key performances, functions and tasks that optimize each for its intended applications. Note that InfiniiMax I and II probe probe heads are compatible to each other, but they are not compatible with InfiniiMax III/III+ and vice versa. InfiniiMax I/II InfiniiMax III+ InfiniiMax III Bandwidth 1.5 - 12 GHz 4 - 20 GHz 16 - 30 GHz Probe loading 50 k diff at DC 100 k diff at DC 1 k diff at > 10 kHz 100 k diff at DC 1 k diff at > 10 kHz InfiniiMode No Yes No Available probe heads/tips Browser (diff, SE), Solder-in (diff, SE), ZIF (diff), QuickTip (diff), (Socketed (diff), SMA (diff)) Browser (diff), Solder-in (InfiniiMode, diff), ZIF (diff), QuickTip (InfiniiMode w/InfiniiMax III+, diff with InfiniiMax III), 2.92mm/SMA (InfiniiMode w/ InfiniiMax III+) Probe interface AutoProbe I AutoProbe I (N2830A Series) AutoProbe II (N7000A Series) AutoProbe II When to use <12 GHz InfiniiMode High speed signals with low source impedance or with embedded clock When not to use >12 GHz, InfiniiMode Signal with "high Z" typically found in mobile device communication standards and devices (e.i., MIPI d-phy, LP DDR, eMMC etc) 06 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet InfiniiMax Active Probe System Overview - InfiniiMax III/III+ Probing System Key features -- Full 30 GHz bandwidth to the probe tip -- InfiniiMode probing for making differential, single-ended and common mode measurements with a single probe (InfiniiMax III+) -- Industry's highest fidelity and accuracy due to bandwidth and extremely low loading -- Probe amplifiers loaded with measured S-parameters for more accurate response correction -- Bandwidth upgradeable (InfiniiMax III only) -- Variety of probe heads for different use models with maximum usability Scope compatibility Scope family Compatible probes V-Series, 90000X/Q, Z-Series N2800A, N2801A, N2802A, N2803A, N7000A, N7001A, N7002A, N7003A S-Series, 90000A Series N2830A, N2831A, N2832A The InfiniiMax III/III+ probing system provides the highest performance and low loading to allow for a completely new level of signal fidelity and accuracy. Eleven different InfiniiMax III/III+ probe amplifiers ranging from 4 GHz to 30 GHz are available for matching your probing solution to your performance and budget requirements. The InfiniiMax III+ probing system is the next generation of InfiniiMax probing. It greatly expands the measurement capability and usability of probes capable of measuring all components of a differential signal with the built-in InfiniiMode technology. InfiniiMax III amp with ZIF head/tips InfiniiMax III ZIF head and tip QuickTip head and tip N2830A InfiniiMax III+ amp with QuickTip head 07 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet InfiniiMax Active Probe System Overview - InfiniiMax III/III+ Probing System (continued) Characteristics performance plots: N2803A 30-GHz probe amp with N5445A 30-GHz browser Frequency response plot with 1 mm span Time domain response plot with 1 mm span Differential input impedance 08 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet InfiniiMax Active Probe System Overview - InfiniiMax III/III+ Probing System (continued) InfiniiMax III/III+ probe heads InfiniiMax III/III+ probe heads are recommended for InfiniiMax III N2800A/01A/02A/03A and InfiniiMax III+ N2830A/31A/32A and N7000A/01A/02A/03A probe amplifiers. Any probe heads for InfiniiMax I or II are not compatible with InfiniiMax III or III+ amplifier and vice versa. Probe heads Model numbers BW and input loading Key features Differential browser head N5445A 30 GHz, Cdiff = 35 fF, Cse = 50 fF, Rdiff = 100 k, Rse = 50 k Z axis compliance and variable spacing from 20 mil to 125 mils, integrated LED lighting ZIF probe head/tips N5439A head, N2838A 450 PCB tip, N5440A 450 ceramic tip, N5447A 200 ceramic tip 28 GHz, Cdiff = 95 fF, Cse = 130 fF, with N2838A: Cdiff = 32 fF, Cse = 44 fF, with N5440A: Rdiff = 100 k, Rse = 50 k N5447A: Rdiff = 50 k, Rse = 25 k with N5440A/N2838A Extremely low loading, Variable spacing from 5 mil to 80mil , User replaceable damping resistor tips (N2838A only) 2.92 mm/3.5 mm/ SMA probe head N5444A 28 GHz, N/A, 55 to Vterm Provides termination voltage of 4 V controlled by scope or externally. Supports InfiniiMode with InfiniiMax III+ amp Solder-in head N5441A 16 GHz, Cdiff = 77 fF, Cse = 105 fF, Rdiff=100 k, Rse = 50 k 26 GHz, Cdiff = 108 fF, Cse = 140 fF, Rdiff=100 k, Rse=50 k Economical and semi-permanent connection, variable span of leads ranges from 5 mil to 80 mil, user replaceable damping resistor tips (N2836A only). N2836A supports InfiniiMode with InfiniiMax III+ amp 16 GHz (with InfiniiMax III/III+), 13 GHz (with InfiniiMax II), Cdiff = 340 fF, Cse = 200 fF Compatible with I/II/III/III+ amp. Supports InfiniiMode with InfiniiMax III+ amp . For using QuickTip with InfiniiMax I/II amp, choose the N2851A QuickTip head for InfiniiMax I/II and N2849A QuickTip tips. N2836A Quick tip N2848 QuickTip head for InfiniiMax III/III+, N2849A QuickTip tips 09 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet InfiniiMax Active Probe System Overview - InfiniiMax III/III+ Probing System (continued) InfiniiMax III/III+ probing system family diagram 10 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet InfiniiMax Active Probe System Overview - InfiniiMax III/III+ Probing System (continued) Performance specifications and characteristics InfiniiMax III/III+ warranted specifications Probe head Probe amp Bandwidth DC input N5440A_N5439A ceramic 450 ZIF tip and ZIF probe head N2803A 30 GHz probe amp 26 GHz Rdiff = 100 k 2%, Rse = 50 k 2% N5445A 450 browser N2803A 30 GHz probe amp 28 GHz Rdiff =1 00 k 2%, Rse = 50 k 2% N2836A 450 solder-in probe head vertical orientation with no ground wires Differential mode N2832A 13GHz probe amp 13 GHz Rdiff = 100 k 2%, Rse = 50 k 2% InfiniiMax III/III+ probe head characteristics These characteristics are mainly determined by the probe head. Performance numbers listed are: -3 dB bandwidth/10-90% transition time/20-80% transition time. Performance listed is with the highest bandwidth probe amp models in each family. Performance with lower bandwidth amps is the lower of the: AmpBW, (.434/AmpBW), (.308/AmpBW), or bandwidth measured with the highest bandwidth amp in the family. InfiniiMax III N2803A 30-GHz probe amp InfiniiMax III+ N7003A 20-GHz probe amp Probe head Input C Differential mode Differential mode Single-ended mode N5440A_N5439A ceramic 450 ZIF tip and ZIF probe head Cdiff=32 fF; Cse=44 fF 28 GHz, 15.5 pS, 11.0 pS 20 GHz, 21.7 pS, 15.4 pS n/a N5447A_N5439A ceramic 200 ZIF tip and ZIF probe head Cdiff=32 fF; Cse=44 fF 28 GHz, 15.5 pS, 11.0 pS n/a N5445A 450 browser Cdiff=35 fF; Cse=50 fF 30 GHz, 14.5 pS, 10.3 pS 20 GHz, 21.7 pS, 15.4 pS n/a N5441A 450 solder-in probe head Cdiff = 77 fF; Cse = 105 fF 17.2 GHz, 34.8 pS, 26.6 pS 20 GHz, 21.7 pS, 15.4 pS n/a N2838A_N5439A PC board 450 ZIF tip and ZIF probe head Cdiff=95 fF; Cse=130 fF 25 GHz, 17.4 pS, 12.3 pS 20 GHz, 21.7 pS, 15.4 pS n/a N2836A 450 solder-in probe head vertical orientation with no ground wires Cdiff=108 fF; Cse=140 fF 27 GHz, 16.1 pS, 11.4 pS 20 GHz, 21.7 pS, 15.4 pS n/a N2836A 450 solder-in probe head flat orientation with minimum length ground wires Cdiff=108 fF; Cse=140 fF 27 GHz, 16.1 pS, 11.4 pS Differential: 20 GHz, 21.7 pS, 15.4 pS Single-ended: 20 GHz, 21.7 pS, 15.4 pS Common mode: 20 GHz, 21.7 pS, 15.4 pS N2849A_N2848A 450 QuickTip and QuickTip probe head with ground wires connected Cdiff=200 fF; Cs=340 fF 16 GHz, 27.1 pS, 19.3 pS Differential: 20 GHz, 21.7 pS, 15.4 pS Single-ended: 13 GHz, 33.4 pS, 23.7 pS Common mode: 13 GHz, 33.4 pS, 23.7 pS N5444A 2.92 mm, SMA, 3.5 mm probe head n/a 28 GHz, 15.5 pS, 11.0 pS Differential: 20 GHz, 21.7 pS, 15.4 pS Single-ended: 20 GHz, 21.7 pS, 15.4 pS Common mode: 20 GHz, 21.7 pS, 15.4 pS Common mode 11 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet InfiniiMax Active Probe System Overview - InfiniiMax III/III+ Probing System (continued) InfiniiMax III/III+ probe amp characteristics These characteristics are mainly determined by the probe amp. N280XA InfiniiMax III probe amp N700xA InfiniiMax III+ probe amp Features 450 probe heads 200 probe heads N5444A 2.92 mm, SMA, 450 probe heads 3.5 mm probe head N5444A 2.92 mm, SMA, 3.5 mm probe head DC input resistance Rse=50 k 2% each input to ground, Rdiff=100 k 2% and Rcm=25 k 2% Rse=50 k 2% each input to ground, Rdiff=100 k 2% and Rcm=25 k 2% 55 to Vterm Rse=50 k 2% each input to ground, Rdiff=100 k 2% and Rcm=25 k 2% 55 to Vterm Input resistance >10 kHz Rse=500 each input to ground, Rdiff=1 k and Rcm=250 Rse=500 each input to ground, Rdiff=1 k and Rcm=250 50 to .901*Vterm Rse=500 each input to ground, Rdiff=1 k and Rcm=250 50 to .901*Vterm Input voltage range (differential or single-ended) 1.6 Vpp, 0.8 V (HD2&3 < -34 dbc), 2.5 Vpp, 1.25 V (HD2&3 < -38 dbc) 0.8 Vpp, 0.4 V (HD2&3 < -34 dbc), 1.6 Vpp, 0.8 V (HD2&3 < -38 dbc) 1.6 Vpp, 0.8 V (HD2&3 < -34 dbc), 2.5 Vpp, 1.25 V (HD2&3 < -38 dbc) 2.5 Vpp or 1.25 V at 5:1 attenuation, 5.0 Vpp or 2.50 V at 10:1 attenuation 2.5 Vpp or 1.25 V at 5:1 attenuation, 5.0 Vpp or 2.50 V at 10:1 attenuation without violating max input power Max input power n/a n/a 125 mW n/a calculated by {[rms(vin-vterm)]^2/55]} for each input 125 mW calculated by {[rms(vin-vterm)]^2/55]} for each input Input common mode range 12 VDC to 250 Hz, 1.25 V > 250 Hz 6 VDC to 250 Hz, 0.65 V > 250 Hz 6 VDC to 250 Hz, 1.25 V > 250 Hz without violating max input power 7 VDC to 100 Hz, 1.25 V > 100 Hz at 5:1 attenuation, 2.5 V > 100 Hz at 10:1 attenuation 6 VDC to 100 Hz, 1.25 V > 100 Hz at 5:1 attenuation, 2.5 V > 100 Hz at 10:1 attenuation without violating max input power DC attenuation ratio 6:1 3:1 6:1 5:1 or 10:1 Automatically selected based on volts/division (all modes) 5:1 or 10:1 Automatically selected based on volts/division (all modes) Offset range (for probing a single-ended signal) 16 V 8V 6 V without violating max input power 16 V 6 V without violating max input power Input referred noise spectral density 23.9 nV/rt (Hz) 12.0 nV/rt (Hz) 23.9 nV/rt (Hz) Diff 5:1 atten 33.5 nV/rt(Hz), Diff 10:1 atten 53.9 nV/rt(Hz), SE A or B 5:1 atten 27.8 nV/rt(Hz), SE A or B 10:1 atten 47.7 nV/rt(Hz), CM 5:1 atten 21.8 nV/rt(Hz), CM 10:1 atten 38.4 nV/rt(Hz) Input referred noise example 4 mVrms with 2 mVrms with 4 mVrms 28 GHz probe head and 28 GHz probe head and 30 GHZ probe amp 30 GHz probe amp Maximum input voltage 18 Vpeak Cat 1 18 Vpeak Cat 1 4.5 mVrms in diff mode 5:1 atten with >= 18 GHz probe head and 13 GHz probe amp 8 Vpeak without violating 18 Vpeak Cat 1 max input power 4.5 mVrms in diff mode 5:1 atten with 28 GHz N5444A probe head and 13 GHz probe amp 8 Vpeak without violating max input power 12 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet InfiniiMax Active Probe System Overview - InfiniiMax III/III+ Probing System (continued) Ordering information InfiniiMax III/III+ probe amplifier models Model number Description Recommended oscilloscope N2803A 30 GHz InfiniiMax III probe amplifier Infiniium 90000X/Q, Z-Series 28 GHz - 63 GHz models N2802A 25 GHz InfiniiMax III probe amplifier Infiniium 90000X/Q, Z-Series 25 GHz models N7003A 20 GHz InfiniiMax III+ probe amplifier Infiniium V-Series, 90000Q, Z-Series 20 GHz models N2801A 20 GHz InfiniiMax III probe amplifier Infiniium 90000X/Q, Z-Series 20 GHz models N7002A 16 GHz InfiniiMax III+ probe amplifier Infiniium V-Series, 90000X Series 16 GHz models N2800A 16 GHz InfiniiMax III probe amplifier Infiniium 90000X Series 16 GHz models N7001A 13 GHz InfiniiMax III+ probe amplifier Infiniium V-Series, 90000X Series 13 GHz models N2832A 13 GHz InfiniiMax III+ probe amplifier Infiniium 90000X 13 GHz and 90000A models N7000A 8 GHz InfiniiMax III+ probe amplifier Infiniium V-Series 8 GHz models N2831A 8 GHz InfiniiMax III+ probe amplifier Infiniium 90000A and S-Series N2830A 4 GHz InfiniiMax III+ probe amplifier Infiniium 90000A and S-Series Note: InfiniiMax III and III+ probe amps are not compatible with existing InfiniiMax I or II probe heads. InfiniiMax III/III+ probe heads Model number Description Notes N2848A InfiniiMax III QuickTip probe head Compatible with InfiniiMax III/III+ amp Supports InfiniiMode with InfiniiMax III+ amp , Order N2849A QuickTip tips (set of 4) N5445A InfiniiMax III browser head Order N5476A for replacement probe tips (set of 4) N5439A InfiniiMax III ZIF probe head Order N2838A PC board ZIF (450 ), N5440A Ceramic ZIF (450 ) or N5447A Ceramic ZIF (200 ) for a set of 5 ZIF tips with plastic sporks N5444A InfiniiMax III 2.92 mm/3.5 mm/SMA probe head Order N5448A 2.92 mm head flex cables to extend the cable length. Supports InfiniiMode with InfiniiMax III+ amp N5441A InfiniiMax lll 16 GHz solder-in probe head N2836A InfiniiMax III 26 GHz solder-in probe head Supports InfiniiMode with InfiniiMax III+ amp Note: N54xxA InfiniiMax III/III+ probe heads are not compatible with InfiniiMax I or II probe amps. InfiniiMax III probe adapters Model number Description Notes N5442A Precision BNC adapter (50 ) For use with InfiniiMax I/II/III+ 1130A/31A/32A/34A/68A/69A and N2830A/31A/32A probes, N2750A-52A, N2795A/96A/97A, 1156A-58A etc. N5449A High impedance probe adapter Includes one N2873A 500MHz 10:1 passive probe N5477A Sampling scope adapter For InfiniiMax III amp to use with Keysight 86100C DCA-J sampling scope N1022B Probe adapter For InfiniiMax III+ amp to use with 86100C DCA-J sampling scope N5443A Performance verification and deskew fixture For InfiniiMax III and InfiniiMax III+ > 13 GHz E2655C Performance verification and deskew fixture For InfiniiMax III+ <=13 GHz and InfiniiMax I/II 13 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet InfiniiMax Active Probe System Overview - InfiniiMax III/III+ Probing System (continued) Ordering information (cont'd) Probe bandwidth upgrade options (for InfiniiMax III only) Model number Description N5446A-001 16 GHz to 20 GHz bandwidth upgrade N5446A-002 20 GHz to 25 GHz bandwidth upgrade N5446A-003 25 GHz to 30 GHz bandwidth upgrade N5446A-004 16 GHz to 25 GHz bandwidth upgrade N5446A-005 16 GHz to 30 GHz bandwidth upgrade N5446A-006 20 GHz to 30 GHz bandwidth upgrade Notes Note: Purchase two or more upgrade options to go from 16 to 25 or 30 GHz and 20 to 30 GHz. To upgrade the probe bandwidth, you simply need to send the probe to the Keysight service center. Other recommended accessories for InfiniiMax III/III+ probing system Model number Description Notes N2787A 3D probe positioner For hands-free probing N5450B Extreme temperature extension cable 1 m long, use N5441A solder-in head for extreme temperature probing with InfiniiMax III/III+ N2812A High performance input cable, 2.92 mm connectors, 1 m length For use with Infiniium 90000-X/Q Series oscilloscope MV-23 Carson Optical MagniVisor www.carsonoptical.com/Magnifiers 14 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet InfiniiMax Active Probe System Overview - InfiniiMax II Probing System Key features -- Up to 13 GHz bandwidth for differential, solder-in, browser and SMA connections -- Low noise and flat frequency response -- Industry's widest variety of differential probe head types Scope compatibility Scope family Recommended probes DSO90000, DSA90000, DSO80000, DSA80000 Series 1168A, 1169A The InfiniiMax II series 1168A/69A probing system designed to be used with Infiniium 80000A and 90000A Series oscilloscopes provides real-time bandwidth to 12 GHz specified and has 13 GHz typical performance. The innovative InfiniiMax probing system supports even the most demanding mechanical access requirements without sacrificing performance. Characterized performance plots: 1169A with N5381A differential solder-in probe head Graph of Vin and Vout of 1169A and N5381A solder-in head with a 25 58 psec step generator Frequency response of 1169A and N5381A with a 25 source Common mode rejection ratio of 1169A 15 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet InfiniiMax Active Probe System Overview - InfiniiMax II Probing System (continued) Ordering information InfiniiMax II Series probe amplifiers Model number Bandwidth Description 1169A 12 GHz (spec) 13 GHz (typical) InfiniiMax II probe amplifier - order one or more probe heads 1168A 10 GHz InfiniiMax II probe amplifier - order one or more probe heads InfiniiMax probe amplifier specifications: Dynamic range = 3.3 V, DC offset range = 16 V, maximum voltage = 30 V InfiniiMax II Series probe heads InfiniiMax II Series probe heads are recommended for 1169A/68A probe amplifiers. When used with a DSO81304A or DSO91304A, the N5380B, N5381A, and N5382A will typically achieve 13 GHz bandwidth. Probe head Model number Differential measurement (BW, input C, input R) Single-ended measurement (BW, input C, input R) Hi-BW differential SMA N5380B 12 GHz 12 GHz Hi-BW differential solder-in N5381A 12 GHz, 0.21 pF, 50 k 12 GHz, 0.35 pF, 25 k Hi-BW differential browser N5382A 12 GHz, 0.21 pF, 50 k 12 GHz, 0.35 pF, 25 k ZIF solder-in N5425A with N5426A with N5451A 7mm, 0 deg with N5451A 11mm, 0 deg with N2884A 12 GHz, 0.33 pF, 50 k 9.9 GHz, -- , 50 k 5 GHz, -- , 50 k 12 GHz, 350 fF, 50 k 12 GHz, 0.53 pF, 25 k 9.9 GHz, 0.6 pF, 25 k 5 GHz, 0.68 pF, 25 k 12 GHz, 320 fF, 25k InfiniiMax I Series probe heads can be used with 1169A/68A probe amplifiers with limitations. Probe head Model number Differential measurement (BW, input C, input R) Single-ended measurement (BW, input C, input R) Differential solder-in (Higher loading, high frequency response variation) E2677A 12 GHz, 0.27 pF, 50 k 12 GHz, 0.44 pF, 25 k Differential socket (Higher loading) E2678B 12 GHz, 0.34 pF, 50 k 12 GHz, 0.56 pF, 25 k Differential browser - wide span E2675B 6 GHz, 0.32 pF, 50 k 6 GHz, 0.57 pF, 25 k Single-ended solder-in (must bandlimit input to 6 GHz) E2679A N/A 6 GHz, 0.50 pF, 25 k Single-ended browser E2676A N/A 6 GHz, 0.67 pF, 25 k 16 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet InfiniiMax Active Probe System Overview - InfiniiMax II Probing System (continued) Overcoming measurement challenges with InfiniiMax probe InfiniiMax probe is not just for Infiniium scope The benefits of Keysight's award winning InfiniiMax probes are not restricted to Keysight Infiniium oscilloscopes. A variety of accessories are available that allow you to use InfiniiMax probes with other test equipment, such as spectrum analyzers and sampling oscilloscopes. To learn more about how to use the InfiniiMax probe with your test equipment other than Keysight Infiniium oscilloscopes, refer to the Keysight literature number 5989-1869EN. Operating at high or low temperatures You may need to monitor a system in a temperature chamber with an oscilloscope probe to verify performance over a wide range of operating temperatures, or to determine the cause of failures at high or low temperatures. Keysight InfiniiMax I/II probe amplifiers have a specified operating temperature range from 5 C to 40 C. However, the probe heads can be operated over a much wider range. You can use the Keysight N5450B extension cable set to physically separate the probe heads from the probe amplifiers. This will allow you to operate the probe heads inside a temperature chamber with the probe amplifier located outside the temperature chamber. To learn more about how to extend the operating range of the InfiniiMax probes in temperature, refer to the Keysight literature number 5989-7587EN. Increasing the voltage dynamic range and offset range The dynamic range of the InfiniiMax probes is 5 V p-p for InfiniiMax I and 3.3 V p-p for InfiniiMax II. For applications that need to measure larger signals with faster edges, the N2880A in-line coaxial attenuator kit allows you to increase the dynamic range of the probe system up to 50 Vpp and the offset range up to 30V, without affecting the bandwidth or rise time characteristics of the probe system. The N2881A DC blocking capacitors can be used in series with the N2880A InfiniiMax in-line attenuator to block out unwanted DC components of the input signal up to 30 V. To learn more about how to extend the operating range of the InfiniiMax probes in input range, refer to the Keysight literature number 5989-7587EN. How would I measure small AC riding on top of large DC with InfiniiMax probe? It is challenging to measure very small signals riding on top of large signals with scopes, as most scopes have limited dynamic ranges and offset ranges. Consider using an InfiniiMax active probe which provides a huge offset range that can allow you to make measurements you need. To learn more about how to use the InfiniiMax probe's offset range, refer to the Keysight literature number 5990-8255EN and 5988-9264EN. Probe offset Normal scope channel offset used when probing signal ended signals used when probing differential signals Plus probe tip Scope channel Minus probe tip Note: minus probe tip not present if using signal-ended probe heads Differential amplifier Probe Scope 17 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet InfiniiMax Active Probe System Overview - InfiniiMax I and II Probing System InfiniiMax offers you the highest performance available for measuring differential and singleended signals, with flexible connectivity solutions for today's high-density ICs and circuit boards. InfiniiMax probes have fully characterized performance for all of their various probe heads. This includes: -- Swept frequency response plot -- Common mode rejection versus frequency plot -- Impedance versus frequency plot -- Time-domain probe loading plot -- Time-domain probe tracking plot Controlled impedance transmission lines in every probe head deliver full performance versus the performance limitations introduced by traditional wire accessories. Probe interface software allows you to save the calibration information for up to 10 different probe heads per channel and will automatically retrieve calibration data for a probe amplifier when attached to the scope. High-input impedance active probes minimize loading, support differential measurements and DC offset, and can compensate for cable loss. Probe calibration software delivers the most accurate probe measurements and linear phase response and allows various probe combinations to be deskewed to the same reference time. A flat frequency response over the entire probe bandwidth eliminates the distortion and frequencydependent loading effects that are present in probes that have an in-band resonance. E2677A 12GHz solder-in differential probe head can be attached to verysmallgeometry circuits for measuring both singleended and differential signals. External mini-coaxial resistors facilitate wider span but have increased high-frequency response variation relative to N5381A. E2679A 6GHz extremely small single-ended, solderin probe heads for probing even the hardesttoreach single-ended signals. N5381A 13GHz highbandwidth solderin differential probe head provides maximum bandwidth and minimizes capacitive loading to 210 fF. Variable spacing from 0.2 to 3.3 mm (8 to 130 mills). N5425A 13GHz highbandwidth solderin differential ZIF probe head and N5426A ZIF tip provides maximum bandwidth with the industry's first lead-free solder-in probe solution in an economical replaceable tip form factor. N5451A 9GHz/5GHz long-wire ZIF tip provides a highbandwidth economical replaceable solder-in tip with extra reach (9 GHz with 7 mm and 5 GHz with 11 mm wire). E2695A 8-GHz differential SMA probe head allows you to connect two SMA cables to make a differential measurement on a single scope channel. This probe head is discontinued. Use the N5380B as a replacement. N5426A N5451A 18 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet InfiniiMax Active Probe System Overview - InfiniiMax I and II Probing System (continued) Six different InfiniiMax probe amplifiers from 1.5 GHz to 13 GHz are available for matching your probing solution to your performance and budget requirements. The 1168/69A InfiniiMax II amplifiers offer up to 13 GHz of bandwidth and the lowest noise floors. The 1134/32/31/30A offer a more cost efficient solution and wider dynamic range. N5382A 13GHz highbandwidth differential browser provides maximum bandwidth for hand-held or probe holder use. Variable spacing from 0.2 to 3.3 mm (8 to 130 mills). N2884A Differential Fine-wire Probing Tip InfiniiMax differential fine-wire probing tip is a high fidelity, high bandwidth solution for probing an active IC. E2675B 6GHz differential browser is the best choice for general-purpose trouble shooting of differential or single-ended signals with z-axis compliance and variable spacing from 0.25 - 5.80 mm (10 - 230 mills). E2676A 6GHz single-ended browser is the best choice for general-purpose probing of single-ended signals when the small size of the probe head is the primary consideration. E2678B 12GHz differential socket probe head can be used to measure either differential or singleended signals via a plug-on socket connection. N2887A InfiniiMax Soft touch Pro Probe Adapter adapts from the Keysight Pro Series (36 ch) Soft touch connectorless logic analyzer foot print to the Keysight InfiniiMax I & II series probe amplifier input connectors. N2880A In-line Attenuator Kit allows you to increase the dynamic range and the offset range of the InfiniiMax probe without affecting the bandwidth. N5380B 13GHz highbandwidth differential SMA probe head provides maximum bandwidth for SMAfixtured differential pairs. N5450B InfiniiMax extreme temperature extension cable provides extra reach into environmental chambers. N2881A DC Blocking Capacitors can be used to in series with the N2880A InfiniiMax in-line attenuators to block out unwanted DC components of the input signal up to 30 V. N2888A InfiniiMax Soft touch half-channel Probe Adapter adapts from the Keysight half-channel (18 ch) Soft touch connectorless logic analyzer foot print to the Keysight InfiniiMax I & II series probe amplifier input connectors. 19 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet InfiniiMax Active Probe System Overview - InfiniiMax II Probing System (continued) InfiniiMax II probing system tree diagram 20 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet InfiniiMax Active Probe System Overview - InfiniiMax II Probing System (continued) Performance characteristics 1169A 1168A 1169A: > 12 GHz (13 GHz typical) 1168A: > 10 GHz 1169A: 28 ps (20 - 80%), 40 ps (10 - 90%) 1169A w/91204A: 25 ps (20 - 80%) 36 ps (10 - 90%) 1169A w/91304A: 23 ps (20 - 80%) 33 ps (10 - 90%) 1168A: 34 ps (20 - 80%), 48 ps (10 - 90%) 1168A w/90804A: 38 ps (20 - 80%) 54 ps (10 - 90%) System bandwidth (-3 dB) 1169A w/91304A: 13 GHz (typical) 1169A w/91204A: 12 GHz 1168A w/90804A: 8 GHz Input capacitance1 Cm = 0.09 pF Cg = 0.26 pF Cdiff = 0.21 pF Cse = 0.35 pF Input resistance* Differential mode resistance = 50 k 2% Single-ended mode resistance = 25 k 2% Input dynamic range 3.3 V peak to peak, 1.65 V Input common mode range 6.75 V dc to 100 Hz; 1.25 V > 100 Hz Maximum signal slew rate 25 V/ns when probing a single-ended signal 40 V/ns when probing a differential signal DC attenuation 3.45:1 Zero offset error referred to input 1.5 mV Offset range 16.0 V when probing single-ended Offset gain accuracy < 1% of setting when probing single-ended Noise referred to input 2.5 mV rms, probe only Propagation delay ~6 ns (this delay can be deskewed relative to other signals) Maximum input voltage 30 V peak, CAT I ESD tolerance > 8 kV from 100 pF, 300 HBM Temperature Operating: 5 C to +40 C Non-operating: 0 C to +70 C Bandwidth* Rise and fall time Probe only When phase compensated by 90000A Series oscilloscope Cm is between tips Cg is to ground for each tip Differential mode capacitance = Cm + Cg/2 Single-ended mode capacitance = Cm + Cg 21 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet InfiniiMax Active Probe System Overview - InfiniiMax I Probing System Key features -- Up to 7 GHz bandwidth for differential, solder-in, browser and SMA connections -- Low noise and flat frequency response -- Wide dynamic range ( 2.5 V) and offset range ( 12 V) Scope compatibility Scope family Recommended probes DSO/DSA90604A 1134A DSO/DSA90404A,DSO/MSO9404A 1132A DSO/DSA90254A, DSO/MSO9254A, 54845/46/53A/B 1131A DSO/MSO9104A, 9064A, 8104A, 5483xB/D 1130A For high-speed differential or single-ended probing in embedded designs, the InfiniiMax 1130A Series differential probe amplifiers are perfect complements to the Infiniium 600 MHz - 6 GHz oscilloscopes. Its extremely low input capacitance, flat frequency response and the patented resistor probe tip technology provide ultra low loading of the DUT and superior signal fidelity. Characterized performance plots: with E2677A differential solder-in probe head Vin and Vout of probe with a 25 , 100 psec step signal Swept frequency response with a 25 source 0 -10 -20 dB -30 -40 -50 -60 Probe input impedance vs. frequency 108 109 Frequency (Hz) Common mode rejection versus frequency 1010 22 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet InfiniiMax Active Probe System Overview - InfiniiMax I Probing System (continued) Keysight 1130A/31A/32A/34A InfiniiMax high-performance active probe system -- InfiniiMax 7 GHz, 5 GHz, 3.5 GHz, and 1.5 GHz probing system -- Each InfiniiMax probe amplifier supports both differential and single-ended measurements for a more cost-effective solution -- Unrivaled InfiniiMax probing accessories support browsing, solder-in, and socket use models at the maximum performance available The Keysight InfiniiMax 1134A, 1132A, 1131A and 1130A probe systems provide 7 GHz, 5 GHz, 3.5 GHz and 1.5 GHz of bandwidth respectively, and offer the following benefits: -- The probes have a flat frequency response over the entire bandwidth specification, eliminating the distortion and loading that affect probes with in-band resonance. The probing system enables engineers to utilize their oscilloscope's entire bandwidth without being limited to measuring only 50 transmission lines or using passive resistive divider probes that produce voltage measurement error and circuit loading. Designers can achieve system measurement bandwidths of 4.5 to 6 GHz even when manually "browsing" with the probe. Solder-in probe heads and solder-in sockets provide even higher bandwidths. -- The Keysight InfiniiMax 1130A series probe system supports a wide variety of real-world applications with an extensive line up of probe heads and accessories. The accessories can meet the most demanding mechanical access requirements. Small probe heads can be placed between densely packed PC boards. Solder-in sockets are available for signals that need frequent measurement. A differential SMA probe head is available to connect to fixtures that have SMA connections. A smart ergonomic design allows users to set the spacing between the probe pins (variable span). When not concerned with minimum probe size, designers can use a browsing sleeve to make holding the probe more comfortable. Both probe tips of the differential probe can "flex" to support various probing angles and target system characteristics (z-axis compliance). Innovative damped-wire accessories compensate for the inductance and capacitance associated with the leads, and prevent distortion of the measured signal. -- The groundbreaking design of Keysight InfiniiMax 1130A probe system also enables users to make either single-ended or differential measurements from a single probe amplifier, depending on their choice of probe head and accessory. This can result in significant savings in cost and time. The common mode rejection of the differential probe head reduces a measurement's noise floor. Overall, the Keysight 1130 series probing system delivers unmatched performance, accuracy and connectivity. InfiniiMax offers you the highest performance available for measuring differential and single-ended signals InfiniiMax: The world's best high-speed oscilloscope probing system EDN Magazine has awarded Keysight's InfiniiMax active probe system the 2002 Innovation of the Year Award. 23 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet InfiniiMax Active Probe System Overview - InfiniiMax I Probing System (continued) Performance characteristics 1130A/31A/32A/34A Probe Bandwidth* 1134A: > 7 GHz 1132A: > 5 GHz 1131A: > 3.5 GHz 1130A: > 1.5 GHz Rise and fall time (10% to 90%) 1134A: 60 psec 1132A: 86 psec 1131A: 100 psec 1130A: 233 psec System bandwidth (-3 dB) 1134A with DSO/DSA90604A: 6 GHz 1132A with DSO/DSA90404A, DSO/MSO9404A: 4 GHz 1131A with DSO/DSA90254A, DSO/MSO9254A: 2.5 GHz 1130A with DSO/MSO9104A: 1 GHz 1130A with DSO/MSO9064A: 600 MHz Input capacitance** Cm = 0.1 pF Cm is between tips. Cg = 0.34 pF Cg is to ground for each tip. Cdiff = 0.27pF Differential mode capacitance = Cm + Cg/2 Cse = 0.44 pF Singe-ended mode capacitance = Cm + Cg Input resistance* Differential mode resistance = 50 k 1% Single-ended mode resistance = 25 k 1% Input dynamic range 2.5 V Input common mode range 6.75 V dc to 100 Hz; 1.25 V >100 Hz Maximum signal slew rate 18 V/ns when probing a single-ended signal 30 V/ns when probing a differential signal DC attenuation 10:1 3% before calibration on oscilloscope 10:1 1% after calibration on oscilloscope Zero offset error referred to input < 30 mV before calibration on oscilloscope < 5 mV after calibration on oscilloscope Offset range* 12.0 V when probing single-ended Offset accuracy < 3 % setting before calibration on oscilloscope < 1 % setting after calibration on oscilloscope Noise referred to input 3.0 mVrms Propagation delay ~6 nsec (This delay can be deskewed relative to other signals.) Maximum input voltage* 30 Vpeak, CAT I ESD tolerance > 8 kV from 100 pF, 300 HBM * Denotes warranted specifications, all others are typical. ** Measured using the probe amplifier and solder-in differential probe head with full bandwidth resistors. 24 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet InfiniiMax Active Probe System Overview - InfiniiMax I Probing System (continued) Ordering information InfiniiMax I probe amplifier models Model number Description 1134A 7 GHz InfiniiMax Probe Amplifier (order one or more probe heads or connectivity kits per amplifier) Quantity 1 1132A 5 GHz InfiniiMax Probe Amplifier (order one or more probe heads or connectivity kits per amplifier) 1 1131A 3.5 GHz InfiniiMax Probe Amplifier (order one or more probe heads or connectivity kits per amplifier) 1 1130A 1.5 GHz InfiniiMax Probe Amplifier (order one or more probe heads or connectivity kits per amplifier) 1 InfiniiMax I connectivity kits models Model number Description Quantity E2669A InfiniiMax connectivity kit for differential/single-ended measurements. Includes one differential browser, four solder-in differential probe heads and two socketed differential probe heads. Includes all necessary accessories. 1 E2668A InfiniiMax connectivity kit for single-ended measurements. Includes one single-ended browser, one solder-in probe heads and one socketed probe heads. Includes all necessary accessories. 1 InfiniiMax I individual probe heads Model number Description Quantity E2675B InfiniiMax differential browser probe head and accessories. Includes 20 replaceable tips and ergonomic handle. Order E2658A for replacement accessories. 1 E2676A InfiniiMax single-ended browser probe head and accessories. Includes 2 ground collar assemblies, 10 replaceable tips, a ground lead socket and ergonomic handle. Order E2663A for replacement accessories. 1 E2677A InfiniiMax differential solder-in probe head and accessories. Includes 20 full bandwidth and 10 medium bandwidth damping resistors. Order E2670B for replacement accessories. 1 E2678B InfiniiMax single-ended/differential socketed probe head and accessories. Includes 48 full bandwidth damping resistors, 6 damped wire accessories, 4 square pin sockets and socket heatshrink. Order E2671A for replacement accessories. 1 E2679A InfiniiMax single-ended solder-in probe head and accessories. Includes 16 full bandwidth and 8 medium bandwidth damping resistors and 24 zero ohm ground resistors. Order E2672A for replacement accessories. 1 InfiniiMax I adapters Model number Description Quantity N1022B Adapts 113X/115X active probes to 86100 Infiniium DCA 1 N2887A InfiniiMax Soft touch Pro probe adapter (36 channel, up to 4 GHz) 1 N2888A InfiniiMax Soft touch half-channel probe adapter (18 channel, up to 4 GHz) 1 25 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet N7010A Active Termination Adapter -- 30-GHz single-ended active termination adapter supporting 2.92 mm/3.5 mm/SMA cable input -- Low attenuation setting (1.16:1) for high SNR, low noise measurements -- Ability to terminate signal to a 50 non-ground voltage (VTERM) -- Compatible with Infiniium 90000Q, Z-Series, or V-Series installed with software version 5.30 or higher To date, most oscilloscopes with 50 inputs terminate to ground by definition. However, a particular communication system often requires the 50 termination to a voltage rather than to ground. The Keysight N7010A active termination adapter is a 30-GHz single-ended adapter featuring a user-adjustable common termination voltage (VTERM) and extremely low noise performance. The termination voltage between -4.0 V to +4.0 V can be controlled internally by the oscilloscope. The N7010A is a single-ended adapter. Two scope channels and two adapters are needed for making differential measurement, which allow the A to GND, B to GND and differential (A-B) signals to be viewed in real time. Utilizing low attenuation ratio setting (1.16:1), the adapter enables an extremely lower noise floor, especially at high-sensitivity vertical scales (< 400 mV) when compared to the Keysight InfiniiMax III probe with the N5444A SMA/2.92 mm head. The adapter is compatible with Infiniium 90000Q, Z-Series, or V-Series with AutoProbe II interface. Key characteristics and specifications N7010A Bandwidth* >30 GHz (warranted), >32 GHz (typical) Rise time (10% - 90%) 14.5 psec Attenuation ratio 1.16:1 Noise with oscilloscope See chart Vin max active signal 1.2 Vpp (not including DC component) Vterm range -4V to +4V Vterm accuracy 2 mV Voffset range -4V to +4V Input signal range (|Vin - Vterm| difference) -0.6V (Vin - Vterm ) +0.6V Input resistance @DC* 50 3 % Max non-destructive input voltage 8V * Warranted specifications 26 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet N7010A Active Termination Adapter (continued) Noise of N71010A with Infiniium V-Series oscilloscopes Vertical noise (mVrms) 100.0 10.0 1.0 0.1 10 mV/div 20 mV/div 50 mV/div 100 mV/div 200 mV/div 500mV/div 8 GHz 0.305 0.541 1.214 2.422 4.844 12.157 1 V/div 24.214 13 GHz 0.420 0.737 1.642 3.246 6.477 16.393 32.502 16 GHz 0.479 0.840 1.864 3.681 7.332 18.636 36.799 20 GHz 0.573 0.991 2.185 4.303 8.531 21.890 42.991 25 GHz 0.703 1.205 2.638 5.156 10.183 26.423 51.548 30 GHz 0.864 1.476 3.207 6.212 12.178 32.057 61.978 Eye diagram comparison with MIPI M-PHY Gear 3 data rate at 5.8304 Gb/s, amplitude swing: = 140 mVpp Figure 1. Direct signal connect to Infiniium scope Figure 2. Signal through N7010A active termination adapter; N7010A doesn't inherently contribute noise 27 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet InfiniiMode Active Probes - N2750A/51A/52A InfiniiMode Probes InfiniiMode active probes N2750A/51A/52A InfiniiMode probes -- 1.5 GHz, 3.5 GHz, and 6 GHz probe bandwidth models -- Dual attenuation ratio (2:1/10:1) -- High input resistance (200 k differential, 100 k single-ended) -- Wide input dynamic range (10 Vpp) and offset range ( 15 V) -- High CMRR (> 60 dB at 1 MHz) -- InfiniiMode probing for making differential, single-ended, and common mode measurements with a single probe -- Built-in quick action scope control for quick access to a variety of scope functions -- Built-in headlight -- Includes solder-in, browser, and socketed tips standard -- AutoProbe interface for auto configuration and probe power for Infiniium scopes Measurement versatility Quick action scope control The N2750A Series differential probes offer 2:1 and 10:1 dual attenuation settings, allowing them to be used for a broad range of applications. Dual attenuation range is automatically configured depending on the size of the input signal. The N2750A Series differential probes provide convenient and quick access to various functions on the scope. You often have a need to control the scope while you hold a probe in your hand. With the quick action scope control feature built into the probe, you can turn the built-in headlight of the probe on and off or control some frequently used scope functions, such as RUN/STOP, auto scale, quick print, quick save, etc., with only the push of a button on the probe. Get control of your most needed function with a push of the quick action control button on the probe. The new differential probes have an input resistance of 200 k (differential) or 100 k (each input to ground) and an extremely low input capacitance of 700 fF to minimize circuit loading. This, accompanied with superior signal fidelity, makes these probes useful for most digital design and debug applications. And with their wide dynamic range (10 Vpp) and offset range (15 V), these probes can be used in a wide variety of analog signal measurements as well. InfiniiMode usability The N2750A Series probes come with new InfiniiMode operation modes. The InfiniiMode allows convenient measurements of differential, single-ended, and common mode signals with a single probe tip without reconnecting the probe to change the connection. The N2750A probe's InfiniiMode provides the following modes of operation. Flexibility in probe use models is also a vital necessity. The probes come standard with three different types of exchangeable probe tips that allow for easy connections to the circuit under test. These probe tips enable you to access multiple signals on anything from header connectors to hard-to-reach, high-density circuitry. The probes are equipped with a white LED headlight to illuminate the circuit under test which will help you see where you are probing. The probes are powered directly by the Infiniium AutoProbe interface, eliminating the need for an additional power supply. -- A - B (differential), -- A - ground (single-ended A) -- B - ground (single-ended B) -- (A+B)/2 - ground (common mode) The N2750A Series InfiniiMode differential probes are a new generation of low-cost, 1.5 GHz, 3.5 GHz, and 6 GHz differential active probes compatible with Infiniium oscilloscope's AutoProbe interface. The InfiniiMode probe allows convenient measurements of differential, single-ended (A and B) and common mode signals with a single probe. 28 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet InfiniiMode Active Probes - N2750A/51A/52A InfiniiMode Probes (continued) Characteristics and specifications Model number N2750A N2751A N2752A Probe bandwidth* (-3 dB) 1.5 GHz 3.5 GHz 6 GHz (warranted), 7 GHz (typical) Rise time, probe only (10-90%) 233 psec 100 psec 58.3 psec System bandwidth (with Keysight oscilloscope) 1 GHz (with Keysight's Infiniium oscilloscope) 2.5 GHz (with Keysight's Infiniium oscilloscope) 4/6 GHz (with Keysight's Infiniium oscilloscope) Input resistance (@DC)* 200 k 2% (differential mode) 100 k 2% (single-ended mode) 50 k 2% (common mode) Input capacitance 700 fF (with browser) Attenuation ratio (@DC) 2:1 / 10:1 Input dynamic range 1 V, 2 Vpp (@2:1) / 5 V, 10 Vpp (@10:1) Input common mode range 15 V (from DC to 100 Hz), 2.5 V (for > 100 Hz) **** Offset range 15 V Offset accuracy** < 3% Maximum non-destructive input voltage 30 V (DC + peak AC) Vout /V in frequency response of N2752A (at 2:1) with browser tip Vout /V in frequency response of N2752A (at 2:1) with browser tip Common mode rejection ratio (red= 2:1, blue= 10:1) 29 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet InfiniiMode Active Probes - N2750A/51A/52A InfiniiMode Probes (continued) Ordering information Model number Description N2750A 1.5 GHz InfiniiMode differential probe N2751A 3.5 GHz InfiniiMode differential probe N2752A 6 GHz InfiniiMode differential probe N2776A Differential browser tips (qty 3) N2777A InfiniiMode solder-in tips (qty 3) N2778A InfiniiMode socketed tips (qty 3) N4822A Socketed tip for USB/ethernet application fixtures (qty 1) The N2750A/51A/52A InfiniiMode probes include two browser tips, two socketed tips, and two solder-in tips as standard. The N4822A is not included in the N2750A-52A probe. Other recommended accessories Model number Description N2787A 3D probe positioner E2655C Performance verification and deskew fixture N5442A Precision BNC adapter for V-Series, 90000X/Q Series oscilloscopes N2750A with browser tip N2750A with socketed tip For more information about the N2750A Series InfiniiMode probes, refer to the data sheet with the Keysight literature number, 5991-0560EN. N2750A with N4822A socketed tip for application fixtures N2750A with solder-in tip 30 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet Single-Ended Active Probes - N2795A/96A/97A Active Probes -- High resistance (1 M) and low capacitance (1 pF) input for low loading -- Wide input dynamic range ( 8 V) and offset range ( 12 V for N2796A/97A, 8 V for N2795A) -- Built-in headlight -- Direct connection to AutoProbe interface (no power supply required) -- N2797A for extreme temperature environmental chamber testing at -40 to +85 C The N2795A/96A are a new generation of low-cost, 1 to 2 GHz single-ended active probes with the AutoProbe interface (compatible with Keysight's Infiniium family of oscilloscopes). These probes integrate many of the characteristics needed for today's general-purpose, high-speed probing-especially in digital system design, component design/characterization, and educational research applications. Its 1 M input resistance and extremely low input capacitance (1 pF) provide ultra low loading of the DUT. This, accompanied with superior signal fidelity, makes these probes useful for most of today's digital logic voltages. Testing devices over extreme temperature ranges is quite common these days. The N2797A 1.5 GHz single-ended active probe is the industry's first low-cost high input impedance active probe with rugged probe tips for environmental chamber testing of ICs and devices. The probe gives the ability to probe signals at drastic temperature swings ranging from -40 to +85 C. The probe provides a 2 m long cable. Order N2798A for re-ordering accessories. The N2795A/96A/97A are equipped with a white LED headlight to illuminate the circuit under test. The probes are powered directly by the Infiniium AutoProbe interface, eliminating the need for an additional power supply. The probes also come with a number of accessories that allow for easy connections to the circuit under test. For more information about N2795A/96A/ 97A active probe, refer to the Keysight N2795A/96A/97A active probe data sheet literature number 5990-6480EN. Characteristics for N2795A, N2796A and N2797A active probes N2795A N2796A N2797A Probe bandwidth* (-3 dB) 1 GHz 2 GHz 1.5 GHz Rise time 350 ps 175 ps 233 ps System bandwidth 600 MHz (with Keysight's 600 MHz Infiniium oscilloscope) Attenuation ratio (at dc) 10:1 0.5% Input dynamic range -8 to +8 V (DC or peak AC) Non-destructive input voltage -20 to +20 V Offset range 8V DC offset error (output zero) 1 mV Low frequency accuracy 0.5% at 70 Hz, 1 Vpp Input resistance* 1 M Input capacitance 1 pF Output impedance 50 1 GHz (with Keysight's 1 GHz Infiniium oscilloscope) 12 V * Denotes warranted electrical specifications after 20 minute warm-up, all others are typical 31 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet Single-Ended Active Probes - N2795A/96A/97A Active Probes (continued) Measurement plots Frequency response of N2796A (Vout/Vin) Time domain step response of N2796A (with Keysight MSO9404A) 3.000 M Impedance (Ohms) 1.000 M 100.0 k 10.00 k 1.000 k 100.0 100.0 k 1.000 M 10.00 M 100.0 M Frequency (Hz) Voltage derating over frequency (N2796A) Input impedance over frequency (Red = measured, Blue = model) 1.000 G 7.000 G 32 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet Single-Ended Active Probes - N2795A/96A/97A Active Probes (continued) Ordering information Model number Description N2795A 1 GHz single-ended active probe N2796A 2 GHz single-ended active probe N2797A 1.5 GHz single-ended active probe Reorderable accessories Model number Description Quantity N4839A Dual-lead socketed adapter, 6 cm 2 N4840A Dual-lead solder-in adapter, 5 cm 2 N4841A Dual-lead socketed adapter, 9 cm 2 N4842A Dual-pin PCB header 2 N4843A Solderable tips 10 N4844A Right angle ground lead, 5 cm 2 N4845A Ground blade 2 N4846A Offset ground 2 N4839A N4840A N4841A N4842A N4843A N4844A N4845A N4846A 33 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet Single-Ended Active Probes - N7020A Power Rail Probe -- 2-GHz single-ended active probe for power rail noise measurement -- 1:1 attenuation ratio ensures low noise signal measurement -- 24 V of probe offset range enables effective elimination of DC component of a power supply. The N7020A power rail probe is a low noise, large offset range oscilloscope probe that enables users to measure small signals riding on top of DC power supplies. -- Low noise: The N7020A power rail probe is a 1:1 attenuation ratio active probe. As a general rule, the higher a probes attenuation ratio, the nosier the signal will be on the oscilloscope. -- Large offset range: The N7020A power rail probe provides 24V of probe offset. This enables users to center the signal on screen while placing the oscilloscope at its maximum vertical sensitivity and zoom-in on the signal. -- Low DC loading: The N7020A power rail probe has 50 k input impedance at DC, minimizing the probe's DC loading of the power rail. -- Large input dynamic range: The N7020A power rail probes 850 mV input dynamic range means that users can measure up to 850 mV deviations of their DC supplies. This is very useful for measuring programmable supplies like those used in micro-controller power saving modes. Characteristics and specifications Probe bandwidth (-3 dB) 2 GHz Attenuation ratio 1:1 Offset range 24 V Input impedance at DC 50 k At > 1 MHz 50 Input dynamic range 850 mV Probe noise 10% of oscilloscope noise Included accessories N7021A coaxial probe head (qty 3), N7022A SMA main cable Output impedance 50 Compatible oscilloscopes Infiniium S-Series or 9000 Series with software rev 5.20 or higher For more information about the N7020A power rail probe, check out the Keysight data sheet with the publication number 5992-0141EN. 34 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet General Purpose Differential Active Probes - N2790A/91A/891A High-Voltage Differential Probes -- 25 to 800 MHz bandwidth -- Switchable attenuation -- Measure up to 1,400 V CAT II and 7 kV CAT I Oscilloscope users often need to make floating measurements where neither point of the measurement is at earth ground. Use N2790A, N2791A, or N2891A high voltage differential probes to make safe and accurate floating measurements with an oscilloscope. The N2790A, N2791A, and N2891A high voltage differential probes allow conventional earth-grounded Keysight oscilloscopes to be used for floating signal measurements. Each probe offers user-selectable attenuation settings that make it highly versatile, allowing it to be used for a broad range of applications. The probe comes with probe tip accessories for use with small and large components in tight spaces. N2790A 100 MHz high voltage differential probe The N2791A and N2891A are compatible with any oscilloscope with 1 M BNC input. The N2791A and N2891A probe power is supplied by the included 4x AA batteries or the USB host port of the scope, or PC via a supplied USB power cable. The N2790A is compatible with the Keysight's AutoProbe interface where the probe power is supplied by the Keysight oscilloscope's probe interface. The N2790A is not compatible with 80000 and 90000 Series oscilloscope. Characteristics for N2790A, N2791A and N2891A differential probe N2790A N2791A N2891A Bandwidth 100 MHz 25 MHz 70 MHz Rise time 3.5 ns 14 ns 5 ns Attenuation ratio 50:1 / 500:1 10:1 / 100:1 100:1 / 1000:1 Input impedance (between inputs) 8 M / 3.5 pF 8 M / 8 pF 100 M / 5 pF Max input voltage to ground 1000 V (CAT II) 600 V (CAT III) 700 V at 100:1 70 V at 10:1 7000 V at 1000:1 700 V at 100:1 Max input voltage between two inputs 1400 V at 500:1 140 V at 50:1 700 V at 100:1 70 V at 10:1 7000 V at 1000:1 700 V at 100:1 N2790A measuring a power supply signal N2791A 25 MHz high voltage differential probe N2891A 70 MHz high voltage differential probe 35 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet General Purpose Differential Active Probes - N2804A/05A High-Voltage High-Speed Differential Probes -- 200 - 300 MHz bandwidth -- Measures up to 300 V differential, 1 kV common mode -- Ideal for high speed power measurements The N2804A and N2805A differential probes provide the superior general-purpose differential signal measurements that are required for high-speed power measurements such as measuring characteristics of switching power devices, DC-DC converters or class D amplifiers, vehicle bus measurements, and high-speed digital system designs. The N2804A 300-MHz differential probe offers 100:1 attenuation ratio, allowing it to be used adequately for high voltage signal measurements. The differential probe has a differential input resistance of 4 M and low input capacitance of 4 pF to minimize circuit loading. The probe comes with a pair of extension leads (30 cm long) with a damping resistor built in to damp out the in-band resonance and provide flat frequency response even while using the extension leads and probe tip accessories. The N2805A is a 200-MHz differential probe designed to provide superior differential signal measurements with long cable length (5 m), making it ideal in an environment where extended cable length is required. This probe comes with an extensive set of probe tip accessories for use with small and large components in tight spaces. N2804A N2805A Bandwidth 300 MHz (without extension leads) 120 MHz (with extension leads) 200 MHz Attenuation ratio 100:1 50:1 DC gain accuracy 1% 1% Input impedance (between inputs) 4 M / 4 pF 4 M / 4 pF Max input voltage (between two inputs) 300 V (DC+ peak AC) and 200 Vrms 200 V (DC+ peak AC) and 200 Vrms CAT II Max input voltage 300 V (DC+ peak AC) and 200 Vrms CATII 1000 V (DC+ peak AC) and 1000 Vrms CATI 500 V (DC+ peak AC) and 500 Vrms CAT I 300 V (DC+ peak AC) and 200 Vrms CATII Cable length 1.2 m 5m Compatible Infiniium oscilloscopes Infiniium S-Series, 9000, 90000 Series with software 5.2 or higher N2804A 300 MHz differential probe N2805A 200 MHz differential probe 36 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet General Purpose Differential Active Probes - 1153A/41A Low-Noise Differential Probes The 1141A is a 1x FET differential probe with 200MHz bandwidth and a 3000:1 CMRR. The probe has a high-input resistance and low-input capacitance of 7 pF to minimize circuit loading. The 1141A must be used with 1142A probe control and power module, which controls input coupling modes dc, dc with variable offset, and dc reject. Two attenuators, 10x and 100x are provided to expand the linear differential input range to 30 V. This probe works with any 50 input oscilloscope. The 1153A is the same 1:1 differential probe with 200 MHz as the 1141A except that it is compatible with the AutoProbe interface, which completely configures the Infiniium scope for the probe. The probe interface recognizes the probe and automatically sets up the proper power, coupling mode, 50 impedance and offset range. The 1142A probe power supply is unnecessary with the 1153A. The probe works with Infiniium 9000, 90000A and 90000X with N5442A. Characteristics for 1153A/41A differential probe 1153A/41A Bandwidth 200 MHz Rise time 1.75 ns Attenuation ratio 10:1 and 100:1 with attenuator High CMRR 3000:1 at 1 MHz 10:1 at 100 MHz Input impedance Between inputs: 1 M / 7 pF Max input voltage 200 Vdc + peak ac (probe alone) 500 Vdc + peak ac (with attenuator) 1153A 1:1 FET differential probe with 200 MHz bandwidth 37 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet General Purpose Differential Active Probes - N2818A/19A General-Purpose Differential Probes The N2818A 200-MHz and N2819A 800-MHz differential probes provide the superior general-purpose differential signal measurements required for today's high-speed power measurements, vehicle bus measurements, and digital system designs. The N2818A and N2819A probes offer a 10:1 attenuation setting and high input resistance and low input capacitance to minimize circuit loading. Both probes are compatible with AutoProbe interface with 50 BNC input. N2818A 200-MHz, 20-V differential probe Characteristics for N2818A and N2819A differential probes N2818A N2819A Bandwidth 200 MHz 800 MHz Rise time 1.75 ns 437 ps Attenuation ratio 10:1 10:1 Probe loading (between inputs) 1 M / 3.5 pF 200 k / 1 pF Max input voltage to ground 60 V 40 V Max input voltage between two inputs 20 V 15 V N2819A 800-MHz, 15-V differential probe Ordering information for Keysight differential probes and power supply Model number Description 1141A 200-MHz differential probe 1142A Probe control and power module for 1141A 1153A 200-MHz differential probe with AutoProbe interface N2790A 100-MHz, 1.4 kV differential probe with AutoProbe interface N2791A 25-MHz, 700-V differential probe N2818A 200-MHz, 20-V differential probe with AutoProbe interface N2819A 800-MHz, 15-V differential probe with AutoProbe interface N2891A 70-MHz, 7,000-V differential probe N4853A Variable pitch browser for N2819A N4854A DC blocking capacitor for N2819A N2804A 300-MHz high voltage differential probe N2805A 200-MHz high voltage differential probe with extended cable length N2816A Probe tip accessory kit for N2804A including 2 each alligator clips, 2 each pincer clips, and 1 extension leads (30 cm) N2817A Probe tip accessory kit for N2805A including 2 each alligator clips, 2 each hook clips, 2 each pincer clips, and 2 each browser tips N4853A variable pitch browser N4854A DC blocking capacitor 38 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet AC/DC Current Probes - 1146B Low-Cost AC/DC Current Probe The 1146B ac/dc current probe provides accurate display and measurement of currents from 100 mA to 100 Arms, dc to 100 kHz, without breaking into the circuit. A battery level indicator and overload indicator help ensure proper readings. It connects directly to the scope through a 2-m coaxial cable with an insulated BNC. This probe works with any 1 M input oscilloscope. Operating characteristics of the 1146B current probe 1146B Bandwidth* dc to 100 kHz (-3 dB) Current range* 100 mV/A:100 mA to 10 A peak 10 mV/A:1 to 100 A peak Output signal 1000 mV peak max AC current accuracy* Range 100 mV/A (50 mA to 10 A peak) 3% of reading 50 mA 10 mV/A (500 mA to 40 A peak) 4% of reading 50 mA 10 mV/A (40 A to 100 A peak) 15% max at 100 A Accuracy Range Accuracy Range Accuracy Noise Range 10 mV/A: 480 V Range 100 mV/A: 3 mV Insertion impedance 0.01 (50/60 Hz) Maximum working voltage 600 Vrms CAT II or 300 Vrms CAT III Maximum common mode voltage 600 Vrms CAT II or 300 Vrms CAT III Influence of adjacent conductor < 0.2 mA/A AC Influence of conductor position 0.5% of reading at 1 kHz in jaw Battery 9 V alkaline (NEDA 1604A, IEC 6LR61) Low battery Green LED on when 6.5 V Battery life 55 hours typical Note: Reference conditions 23 5 C, (73.4 41 C) 20 to 75% relative humidity, dc to 1 kHz, probe zeroed, 1-minute warmup, batteries at 9 V + 0.1 V, external magnetic field <40 A/m, no dc component, no external current carrying conductor, 1 M / 100 pF load, conductor centered in jaw. * Characteristics marked with asterisks are specified performance. Others are typical characteristics. Ordering information Model number Description 1146B 100-kHz current probe 1146B 100 mA to 100 Arms, dc to 100 kHz probe 39 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet AC/DC Current Probes - 1147B/N2893A AC/DC Current Probes The 1147B/N2893A is a wide bandwidth, dc to 50-MHz/100-MHz current probe. The probe offers a flat frequency response across the entire dc to 50-MHz/100-MHz bandwidth, low noise (< -2.5 mArms), and low circuit insertion loss. The 1147B/N2893A probe is compatible with the AutoProbe interface, which completely configures the oscilloscope for the probe when used with the Infiniium 9000 Series scope (1 M input). Probe power is provided by the scope, so there is no need for an external power supply. The N2893A uniquely provides an auto demagnetization and offset elimination feature when used in conjunction with Infiniium scope. The 1147B and N2893A are not compatible with Infiniium 80000 and 90000 Series oscilloscope. Operating characteristics of the 1147B/N2893A current probes 1147B/N2893A Bandwidth (-3 dB) dc to 50 MHz (1147B) dc to 100 MHz (N2893A) Rise time 7 ns or less Maximum current (continuous) 15 A peak, 15 A DC, 10 Arms Maximum peak current (non-continuous) 30 A peak Output voltage rate 0.1 V/A Amplitude accuracy 1% rdg, 10 mA (dc and 45 to 66 Hz, rated current) Noise Equivalent to 2.5 mArms or less (for 20 MHz bandwidth measuring instrument) Temperature coefficient for sensitivity 2% or less (within a range of 0 to 40 C or 32 to 104 F) Effect of external magnetic fields Equivalent to a maximum of 20 mA (in a dc to 60 Hz, 400 A/m magnetic field) Maximum rated power 3 VA (with rated current) Maximum input voltage 300 V CAT I Diameter of measurable conductors 5 mm dia. (0.2 in dia.) Probe interface AutoProbe interface (1 M terminated) Cable lengths Sensor cable: Appox. 1.5 m (59.0 in) Power supply cable: Appox. 1 m (39.4 in) Note: The above specifications are guaranteed at 23 3 C (or 73 5 F) Ordering information Model number Description 1147B 50-MHz current probe with AutoProbe interface N2893A 100-MHz current probe with AutoProbe interface 1147B 50MHz current probe with AutoProbe interface N2893A 100-MHz current probe with AutoProbe interface 40 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet AC/DC Current Probes - N2780B/81B/82B/83B/83L AC/DC Current Probes The N2780B/L Series current probes are high bandwidth, active current probes, featuring flat bandwidth, low noise (2.5 mArms) and low circuit insertion loss. Compatible with any oscilloscope with a 1 M BNC input, the N2780B/L Series current probes offer accurate and reliable solution for measuring DC and AC currents. Because of the split-core design, they can easily clip on and off of a wire In conjunction with the power supply (model N2779A), this probe can be used with any oscilloscope with a high-impedance BNC input. The companion power supply N2779A (3 x 12 Vdc output) lets you connect up to any three N2780B-83B/83L current probes to a single power supply. The N2783L 80 MHz current probe offers 5 m long cable, which allows you to reach DUTs in long distance very easily. Other than the bandwidth performance, the N2783A and N2783L have the same electrical performance. The N2783L also requires the N2779A power supply to power the probe. Operating characteristics of the N2780B/L Series current probes N2780B/L Series Bandwidth (-3 dB) dc to 2 MHz (N2780B) dc to 10 MHz (N2781B) dc to 50 MHz (N2782B) dc to 100 MHz (N2783B) dc to 80 MHz (N2783L) Maximum current (continuous) 500 A (N2780B) 150 A (N2781B) 30 A (N2782B/N2783B/N2783L) Maximum peak current (non-continuous) 700 A peak (N2780B) 300 A peak (N2781B) 50 A peak (N2782B/N2783B/N2783L) Maximum input voltage** 300 V CAT I (N2782B, 83B, 83L) 300 V CAT III, 600 V CAT II (N2780B, 81B) Output voltage rate 0.01 V/A (N2780B/N2781B) 0.1 V/A (N2782B/N2783B /N2783L) Amplitude accuracy* 1.0 % rdg 500 mA (N2780B) 1.0 % rdg 100 mA (N2781B) 1.0 % rdg 10 mA (N2782B) 1.0 % rdg 10 mA (N2783B/N2893L) * The amplitude accuracy specification is guaranteed at 23 C 3 C (or 73 F 5 F). ** Insulated conductor should be used. Ordering information Model number Description N2780B 2-MHz current probe N2781B 10-MHz current probe N2782B 50-MHz current probe N2783B 100-MHz current probe N2779A Power supply for the N2780B/81B/82B/83B/83L current probes N2783L 80-MHz current probe with 5 m cable N2780B Series current probes with N2779A power supply N2783L with 5m long cable 41 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet High-Sensitivity Current Probes - N2820A/21A -- Measure AC/DC currents as low as 50 uA -- Ideal for capturing and analyzing low level current flow in the DUT to characterize sub-circuits or measure current consumption of batterypowered devices or integrated circuits -- Simultaneous high- and low-gain views of the current waveform for more precise wide dynamic range measurement (with N2820A) N2820A high-sensitivity 2-channel current probe As modern battery-powered devices and integrated circuits become more green and energy efficient, there is a growing need to make high-sensitivity, low-level current measurements to ensure the current consumption of these devices is in acceptable limits. The N2820A high-sensitivity probe is engineered to make high-dynamic-range, high-sensitivity measurements to meet today's challenging current measurement needs. The ultra-sensitive N2820A AC/DC current probe can support measurements from 50 uA to 5 A on Keysight oscilloscopes. The N2820A interface uses a make-beforebreak (MBB) connector, allowing you to quickly probe multiple locations on your DUT without having to solder or unsolder the leads. The N2820A 2-channel current probe connects to two oscilloscope channels to provide simultaneous lowand high-gain views for wider dynamic range measurement, while the N2821A 1-channel current probe provides one user-selectable view at a time. Use an area-under-the-curve measurement (Charge) on Infiniium oscilloscopes to easily calculate the integrated current consumptions over time in Ah. The N2820A 2-channel current probe connects to two oscilloscope channels to provide simultaneous low- and high-gain views for wider dynamic range measurement. 42 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet High-Sensitivity Current Probes - N2820A/21A (continued) Probe characteristics and specification Bandwidth (-3 dB) Rise time (Tr = 0.35/bandwidth, 10% - 90%) Minimum measurable current* Maximum measurable current DC amplitude accuracy Gain*** Max input voltage Output impedance Standard accessories Compatible InfiniiVision oscilloscopes * ** *** Zoom-out channel: DC to 3 MHz Zoom-in channel: DC to 500 kHz Zoom-out channel: < 0.116 sec Zoom-in channel: < 0.7 sec 250 A (with N2822A 20 m, 500 mW) 50 A (with N2824A 100 m, 500 mW) 5 mA (with N2825A user-defined 1 m, 500 mW) 50 A (with N2825A user-defined 1 k, 500 mW) 5 A (with N2822A 20 m, 500 mW) 2.2 A (with N2824A 100 m, 500 mW) 5 A** (with N2825A user-defined 1 m, 500 mW) 1.2 mA** (with N2825A user-defined 1 k, 500 mW) 3% or 10 A (whichever is greater) Zoom-in channel: 300 3% Zoom-out channel: 1.97 3% 12 V 1 M -- 1 each 20 m resistor sensor head -- 1 each 100 m resistor sensor head -- 1 each user defined resistor sensor head -- 5 each twisted leads (22 AWG) with sockets -- 5 each twisted leads (22 AWG) without sockets -- 5 each MBB headers -- 5 each MBB receptacles -- 1 each ground lead -- 1 each screw driver -- 1 each passive cable (with N2820A only) -- 1 each user guide manual (English) Infiniium 9000A/H with software version 4.2 or higher Infiniium S Series with software version 5.0 or higher Vsupply is equal to 5 V, solder attached. Max current varies with max resistor power rating. The examples in the table assume 500 mW power rating. Denotes warrantied specification after 20-minute warm up. All others entries in the table are characteristics Ordering information Model numbers Descriptions N2820A High-sensitivity 2-ch current probe N2821A High-sensitivity 1-ch current probe Replacement part numbers N2822A 20 m resistor tips N2824A 100 m resistor tips N2825A User-defined resistor tips N2826A Replacement wires (15.5 cm, 22 AWG bare wires) (qty 5) N2827A Passive cable (for N2820A secondary channel) N2828A Replacement MBB (Make Before Break) headers (qty 5) N2829A Replacement MBB (Make Before Break) receptacles and 15.5 cm, AWG 22 socketed wires (qty 5 each) 43 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet General Purpose Passive Probes - N2870A-76A Passive Probes -- Small 2.5 mm probe tip -- Replaceable spring-loaded probe tip for reliable contact -- 1:1, 10:1, 20:1 and 100:1 attenuation ratios with auto probe ID readout -- Wide compensation range for a variety of scope inputs -- Comes with various probe tip accessories -- Optional probe accessory kits -- N2873A, 500 MHz, 10:1 probe -- Ships with the 9000 Series Infiniium oscilloscope The N2870A Series passive probe family sets new standards in high performance probing of up to 1.5 GHz bandwidth. These general purpose probes and accessories offer high quality measurements at a very reasonable price. Compact 2.5-mm probe head diameter, low input capacitance, and various fine-pitch probe tip accessories make the Keysight N2870A Series passive probes ideal for probing densely populated IC components or surface-mount devices used in today's high-speed digital applications. The sharp probe tip is spring loaded to help engineers keep the probe from slipping off the device under test. Insulating IC caps keep the small probe tip centered on the IC lead and keep it from shorting adjacent leads. Standard flat blade ground connector and self-adhesive copper ground pads help reduce ground inductance, while offering easy ground access. Optional probe tip accessories provide specialized capabilities for demanding applications. N2873A 500 MHz passive probe with standard accessories The N2873A 500 MHz passive probe ships with Keysight's 9000 and S-Series Infiniium oscilloscope. Electrical characteristics Model number Bandwidth (-3 dB) Attenuation ratio* Input C Input R* (Scope and probe) Max input voltage (AC RMS) Scope input coupling Scope comp range N2870A 35 MHz 1:1 39 pF (+oscilloscope) 1 M 55 V CAT II 1 M - N2871A 200 MHz 10:1 9.5 pF 10 M 400 V CAT I 300 V CAT II 1 M 10-25 pF N2872A 350 MHz 10:1 9.5 pF 10 M 400 V CAT I 300 V CAT II 1 M 10-25 pF N2873A 500 MHz 10:1 9.5 pF 10 M 400 V CAT I 300 V CAT II 1 M 10-25 pF N2874A 1.5 GHz 10:1 1.8 pF 500 8.5 V CAT I 50 -- N2875A 500 MHz 20:1 5.6 pF 20 M 400 V CAT I 300 V CAT II 1 M 7-20 pF N2876A 1.5 GHz 100:1 2.2 pF 5 k 21 V CAT I 50 -- * Denotes warranted specifications, all others are typical. Attenuation ratio = 2% at DC, Input R (probe only, N2870A excluded) = 1% Common to all Probe ID readout: Compatible with Keysight's InfiniiVision and Infiniium Series oscilloscopes 44 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet General Purpose Passive Probes - N2870A-76A Passive Probes (continued) Mechanical characteristics -- Weight (probe only): 48 g -- Cable length: 1.3 m -- Ground sleeve diameter: 2.5 mm Environmental characteristics temperature -- Operating: 0 C to +50 C -- Non-operating: -40 C to +70 C Altitude -- Operating: 2,000 m (6,561 ft -- Non-operating: 15,000 (49,212 ft) Humidity -- Operating: 80% room humidity for temperatures up to 31 C, decreasing linearly to 40% at 50 C Pollution degree: 2 Optional accessory kits Model number Description N2877A Deluxe Accessory Kit N2878A General Purpose Accessory Kit N2879A Fine Pitch Accessory Kit N2885A PCB Socket Adapter Kit N4829A Probe tip kit (rigid and spring loaded), qty 10 each N4831A Sprung hook tip, qty 2 (for N2870A/71A/72A/73A/75A) N4836A Dual-lead adapter 2.5 mm, 10 cm, qty 2 N4837A Ground lead 15 cm, qty 2 N4838A 2.5 mm ground spring, qty 2 N4863A 2.5 mm probe tip-to-PCB adapter, horizontal, qty 2 N4864A 2.5 mm probe tip-to-PCB adapter, vertical, qty 2 N4829A N4831A N4836A N4837A N4838A N4863A N4864A 45 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet General Purpose Passive Probes - N2870A-76A Passive Probes (continued) Standard accessories N2871A, N2872A, N2873A, N2875A N2870A N2874A, N2876A Rigid probe tips, qty 2 Spring-loaded probe tips, qty 2 Sprung hook 2.5 mm Short sprung hook 2.5 mm Ground blade 2.5 mm with 2 copper pads IC cap 2.5-0.5 mm green IC cap 2.5-0.65 mm blue IC cap 2.5-0.8 mm gray IC cap 2.5-1.0 mm brown IC cap 2.5-1.27 mm black Insulating cap 2.5 mm Protection cap 2.5 mm BNC adapter 2.5 mm Ground spring 2.5 mm Ground lead 15 cm Trimmer tool Color coded rings 3x4 User's guide manual Other replacement parts Part number Description 0960-2907 Short spring hook 2.5 mm for N2874A and N2876A 1.5 GHz passive probe 0960-2908 10 self-adhesive copper-pads 2X2 cm for N2870A Series probes For other re-orderable accessories for N2870A-76A passive probes, check out the product web page on www.keysight.com/find/probes. 46 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet General Purpose Passive Probes - 1165A Passive Probe -- Standard passive probe for Infiniium 5483x Series -- Compact design, removable probe handle for tight probing areas These general purpose replacement devices are built and tested for high reliability. Kevlar strengthener has been added to the probe cable for extra pull strength. Durable probe tips are replaceable. The compact design significantly reduces the problem of probing densely populated integrated circuit components or the characteristically minute conductors on printed circuit boards. These small, lightweight probes allow measurements that were previously difficult, while reducing the danger of shorting. For tight probing areas, the probe handle can be unscrewed and pulled back along the cable. When probing about the circuit in debug mode, the probes easily slip inside the included browsers. The browsers feature a crown point that digs into solder and avoids the danger of slipping off the test point and shorting to adjacent leads. A pogo pin allows hand movement on the probes without losing contact with the device under test. A snap-on BNC connector simplifies attaching the probe to the scope. Leads are available for connecting to a wide variety of test points. See "Ordering Information" for a complete list. Electrical characteristics Model number Type of probe System bandwidth (scope+probe) Division ratio Input R Input C Scope input R Comp range Length 1165A High impedance, passive 600 MHz typical with 54830B/31B/32B/33A 54830D/31D/32D/33D 10:1 10 M 10 pF 1 M 12 - 14 pF 1.5 m Operating characteristics 1165A passive probe 1165A Approximate propagation delay 6.7 ns Maximum input voltage 300 V (dc + peak ac), CAT II Safety Meets IEC1010-2-31 Pulling strength (BNC to barrel) 12 lb static pull Net weight 2.6 oz 116XA 500 MHz passive probe Environmental characteristics 1165A Temperature (operating) 0 C to +55 C Humidity (operating) Up to 95% relative humidity at 40 C Altitude (operating) Up to 4,600 meters (15,000 ft.) Shock 50 g (400 g tip only) No-slip browser crown point 47 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet General Purpose Passive Probes - 1165A Passive Probe (continued) Ordering information Probe parts supplied Probes and accessories Model number Description 1165A 10:1, 10 M, 1.5 m, miniature passive probe Quantity 1 5063-2143 Probe tip to BNC (m) IC clips: See "Probing Accessories" Horizontal and vertical mini-probe sockets: See "Probing Accessories" Wedge Probe Adapters: See "Probing Accessories" 1 One browser pogo pin (spare) Two SMD clips One generalpurpose retractable hook tip One browser One dual-lead adapter Replacement parts Part number Description Quantity 5063-2135 General purpose retractable hook tip 2 5063-2140 Alligator ground lead 2 5063-2120 Socketed ground lead 1 5063-2115 Browser 1 5063-2147 Dual lead adapter 1 5063-2149 SMD clips 5 01160-68701 Accessory kit (includes four spring grounds, four browser pogo pins, four barrel insulators, one screwdriver) 1 5063-2137 1165A probe tip, brown 5 Two barrel insulators Four spring grounds Two probe tips One alligator ground lead One socketed ground lead One probe One screwdriver Includes user's guide and three-year warranty 48 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet General Purpose Passive Probes - 54006A High Bandwidth Passive Probe -- Useful in probing high-frequency signals with low source impedance -- Supplied with 10:1, 500 and 20:1, 1 k resistor dividers -- Low capacitive loading to extremely high frequencies The Keysight 54006A allows you to probe signals up to 6 GHz using replaceable tips that provide either 10:1 division ratio with 500 input resistance, or a 20:1 division ratio with 1 k input resistance. This 6 GHz probe gives access to circuit nodes that are not 50 or do not have 50 connectors allowing you to see signals at specific points, such as the input to a gate. Keysight 54006A's input capacitive loading is approximately 0.25 pF, allowing you to get very accurate timing measurements for a wide bandwidths of signals. The 54006A probe is a good, low-cost alternative for high-frequency probing where the higher resistive loading is not an issue and the other features of the InfiniiMax probing system are not needed (such as differential inputs and multiple connectivity options). Operating characteristics the 54006A passive probe 54006A Bandwidth (-3 dB) 6 GHz Attenuation ratio 10:1, 20:1 Input resistance 500 , 1 k Input capacitance 0.25 pF Max dc volts 20 V Length in meters (feet) 0.9 m (3 ft) Ordering information Model number Description 54006A* 6 GHz resistor divider probe Includes: One 10:1 500 probe body, six 450 resistors, One 20:1, 1 k probe body, six 950 resistors, One 36 in, 50 coaxial cable, SMA (m-m) One blocking cap, 10 GHz-26 GHz APC - 3,5 (m-f) Quantity * Requires the 54855-67604 SMA to precision-BNC adapter to connect to BNC scope input 54006A for probing high frequency, up to 100 impedance signals 1 49 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet High Voltage Passive Probes - 10076C 100:1 Passive Probe -- Ideal for measuring up to 30 kV -- Up to 500 MHz bandwidth -- 100:1 or 1000:1 attenuation The Keysight 10076C 4 kV 100:1 passive probe gives you the voltage and bandwidth you need for making high-voltage measurements. Its compact design makes it easier to probe today's small power electronics components and its rugged construction means it can withstand rough handling without breaking. The 10076C is compatible with any oscilloscope with 1 M BNC input. For use with the Infiniium 90000 Series scope, use the E2697A high impedance probe adapter. For use with the Infiniium 90000 X- and 90000 Q-Series scope, use the N5449A high impedance probe adapter. 10076C passive probe Operating characteristics the 10076C 100:1 passive probe 10076C Bandwidth 500 MHz (-3 dB) Rise time (calculated) < 0.7 ns Attenuation ratio 100:1 Input resistance 66.7 M (when terminated into 1 M) Input capacitance Approx 3 pF Maximum input 4000 Vpk CAT I, 1000 Vpk CAT II Compensation 6 to 20 pF range Probe readout Yes Cable length 1.8 m 10077A accessory kit for 10076B/c Ordering information Model number Description Quantity 10076C High-voltage probe: includes one retractable hook tip, onegroundbayonet, one IC probing tip, onealligator ground lead and a compensation screwdriver 1 10077A Accessory kit for 10076B/C including 1x retractable hook pin, 1x ground lead, 1x insulation cap, 2x measuring pins and 8x ID tags 1 N2789A Spring ground tip for 10076B/C 1 N2789A spring ground tip for 10076B/C 10076C derating curve 50 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet High Voltage Passive Probes - N2771B 1000:1 Passive Probe -- Ideal for measuring up to 30 kV -- Up to 250 MHz bandwidth -- 100:1 or 1000:1 attenuation The N2771B is a 1000:1 divider probe for the measurement of fast high voltage signals up to 30 kV dc + peak ac, 10 kV rms. The probe's large size and rugged construction provide superior protection. The ground lead is fed through the body of the probe and protrudes behind the safety barrier, keeping the ground connection away from the high voltage. Typical applications include PMTs, motor drives, high voltage switches, magnatrons, and modern projection systems. N2771B high-voltage probe The N2771B is compatible with any oscilloscope with 1 M BNC input. For use with the Infiniium 90000 Series scope, use the E2697A high impedance probe adapter. For use with the Infiniium 90000X and 90000 Q-Series scope, use the N5449A high impedance probe adapter. Operating characteristics the N2771B 1000:1 passive probe N2771B Bandwidth 50 MHz (-3 dB) Rise time < 7 ns Attenuation ratio 1000:1 Input resistance 100 M (when terminated into 1 M) Input capacitance 1 pF Compensation range 6 to 20 pF Max. voltage 15 kV dc, 10 kV rms, 30 kV dc + peak ac Operating temperature 0 to +50 C, 80% RH Storage temperature -20 to +70 C, 90% RH Dimensions 2 cm (max width of probe stem after handle) x 33 cm 7.5 cm (max probe width probe handle) x 33 cm Probe readout No Cable length 2m N2771B derating curve Ordering information Model number Description N2771B High-voltage probe: includes alligator ground lead, 1sharpprobe tip Quantity 1 51 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet Mixed Signal Oscilloscope Logic Probes and Accessories -- Compatible with all 40-pin logic probe -- Flying leads offer flexibility and convenience MSO probes offer great value and performance The logic probe for the MSO9000A and S-Series mixed signal oscilloscopes (MSOs) are the same one used with Keysight industry leading high-performance logic analyzers. This means we can offer the best performance, great value and access to the industry's broadest range of logic probing accessories. Eternal digital cable (part number 54826-61605) The Infiniium MSO9000A and S-Series come with a 54826-68701 16-channel logic probe kit containing a 40-pin (F) to 40-pin (F) logic probe cable assembly (or external digital cable), 2-inch ground leads (qty 5), SMT IC clips (qty 20) and a 16-channel flying lead probe tip assembly. The standard cable gives the MSO the standard 40-pin female input connector that many Keysight logic analyzers have. With this cable, a user can connect a wide variety of logic analyzer probes such as Mictor, Samtec, and Soft Touch probes. For information on these probes, see Probing solutions for logic analyzers (with Keysight literature number 5968-4632E). SMT IC clip (part number 5090-4833) For optimal signal fidelity, connect ground at each logic probe, in addition to taking a common ground to all eight signals via a separate ground connector on the probe pod. Sixteen-channel probe lead set (part number 54838-61608) Ground leads contain 5 short ground leads (part number 5959-9334) Characteristics for Keysight 54826-68701 Logic Probe Kit parts supplied 16-channel probe set leads x1 Analog bandwidth of cable and flying leads 400 MHz Ground leads x5 Input resistance 100 k 2% SMT IC clips x20 Input capacitance 8 pF at the tip External digital cable x1 52 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet Mixed Signal Oscilloscope Logic Probes and Accessories (continued) The 9000 MSO digital channels were architected to be compatible with a wide variety of probing accessories developed over 20 years for logic analyzers. There's a good chance that the logic analyzer accessories you already own work with your MSO. With the standard 40-pin cable that comes with your MSO, the MSO accepts numerous logic analyzer accessories including: -- E5346A 34-channel Mictor connector probe -- E5385A 34-channel Samtec connector -- E5383A 16-channel flying lead set 01650-63203 16-channel termination adapter (also available as a bundle of both the termination adapter and the 40-pin cable with PN 10085-68701) -- E5404A 34-channel soft touch pro connectorless probe -- E5394A 34-channel soft touch connectorless probe -- E5396A 16-channel soft touch connectorless probe -- Any other accessory that connects to a logic analyzer via a 40-pin cable For logic accessories of greater channel width than MSO digital channels (> 16 channels), there are two use models. -- Route up to 16 signals to the probe and don't use the additional probe channels. -- Route up to 32 signals to the probe and measure 1/2 of them at a time. Simply plug the 40-pin cable to the other side of the probe to see the other 1/2 of the signals. E5346A 34-channel Mictor connector probe E5396A 16-ch (half size) soft touch connectorless probe E5385A 34-channel Samtec connector probe 53 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet Probing Accessories - InfiniiMax Probe InfiniiMax 1130A/31A/32A/34A and InfiniiMax II 1168A/69A probe accessories Unrivaled InfiniiMax and InfiniiMax II probing accessories support browsing, solder-in, socket, and SMA use models at the maximum performance available E2669A InfiniiMax connectivity kit for differential/single-ended measurements E2668A InfiniiMax connectivity kit for single-ended measurements E2675B InfiniiMax differential browser probe head and accessories (6-GHz BW) E2676A InfiniiMax single-ended browser probe head and accessories (6-GHz BW) E2677A InfiniiMax differential solder-in probe head and accessories (12-GHz BW) E2678B InfiniiMax single-ended/differential socketed probe head and accessories (12-GHz BW) E2679A InfiniiMax single-ended solder-in probe head and accessories (6-GHz BW) N2851A InfiniiMax I/II QuickTip probe head (13-GHz BW, order N2849A QuickTip tips) (12-GHz BW) N5425A/N5426A InfiniiMax differential ZIF solder-in probe head and ZIF probe tips (12-GHz BW) N2851A InfiniiMax I/II QuickTip probe head (13-GHz BW, order N2849A QuickTip tips) N5451A InfiniiMax long-wire ZIF probe tips (for use with N5425A ZIF probe head) N5450B InfiniiMax extreme temperature extension cable (allows for probing in temperatures ranging from -55 to 150 C) N2880A InfiniiMax in-line attenuator kit (pairs of 6, 12, and 20 dB attenuators in a kit) N2881A InfiniiMax DC blocking caps (a pair of 30-Vdc blocking caps) N2884A InfiniiMax fine-wire probe tips for wafer probing (for use with N5425A ZIF head) N5380B InfiniiMax II differential SMA adapter (12-GHz BW) N5381A InfiniiMax II differential solder-in probe head and accessories (12-GHz BW) N5382A InfiniiMax II differential browser (12-GHz BW) N2887A InfiniiMax Soft touch Pro probe interface adapter (4 GHz) N2888A InfiniiMax Soft touch half-channel probe interface adapter (4 GHz) Fully compatible with 1130/31/32/34A InfiniiMax probe amplifier and compatible 1168A/69A InfiniiMax II probe amplifier with limitations Recommended for use with InfiniiMax II 1168A/69A probe amplifier N5381A is compatible with InfiniiMax I amps, (select E2677A in the probe menu) InfiniiMax III N2800A/01A/02A/03A and InfiniiMax III+ N2830A/31A/32A/N7000A/01A/02A/03A probe accessories N5445A InfiniiMax III browser head (30 GHz) Order N5476A for replacement probe tips (set of 4) N2848A InfiniiMax III QuickTip probe head (16 GHz) Supports InfiniiMode with InfiniiMax III+ amp. Order N2849A QuickTip tips (set of 4 tips) N5439A InfiniiMax III ZIF probe head (28 GHz) Order N2838A (450 ), N5440A (450 ) or N5447A (200 ) for a set of 5 ZIF tips with plastic sporks N5444A InfiniiMax III 2.92 mm/3.5 mm/SMA probe head (28 GHz) Order N5448A 3.5/2.92 mm head flex cable to extend the cable length. Supports InfiniiMode with InfiniiMax III+ amp N2836A InfiniiMax III solder-in probe head (26 GHz) Supports InfiniiMode with InfiniiMax III+ amp N5441A InfiniiMax lll solder-in probe head (16 GHz) InfiniiMax probe with N5450B extreme temperature extension cable N2880A InfiniiMax in-line attenuator (probe amplifier and head not included) N2884A InfiniiMax fine-wire probe tip (ZIF probe head not included) 54 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet Probing Accessories - N2744A T2A Probe Interface Adapter -- Enables Tektronix TekProbe-BNC level 2 probes to connect to Keysight's AutoProbe interface on InfiniiVision 3000X, 4000X, 6000X, 5000, 6000, 7000, and Infiniium 9000, 90000, and S-Series oscilloscopes -- An easy-to-use plug-on adapter to the Keysight oscilloscope's AutoProbe interface -- Provides necessary probe power, calibration, and offset control as needed to the attached TekProbe probe The N2744A T2A interface adapter enables selected TekProbe interface level 2 probes to be used with Keysight oscilloscopes with AutoProbe interface. Existing TekProbe-BNC probe types can simply be plugged into the T2A adapter, which is then plugged directly into any AutoProbe input channel on an InfiniiVision or Infiniium oscilloscope. Select the probe model in the scope menu and the Keysight oscilloscope sets up the attenuation factor and the probe type automatically. The T2A interface adapter supplies the necessary probe power, calibration (for selected models only), and offset control as used by the connected TekProbe probe. The adapter is targeted for customers using both Tek active probes with TekProbe-BNC level 2 interfaces and Keysight oscilloscopes with the AutoProbe interface. Tek probe compatibility Single-ended active probes P6243 Single-ended active probe, 1 GHz, 10:1 without offset control P6245 Single-ended active probe, 1.5 GHz, 10:1 with offset control P6205 Single-ended active probe, 750 MHz, 10:1 without offset control P6241 Single-ended active probe, 4 GHz, 10:1 with offset control P6249 Single-ended active probe, 4 GHz, 5:1 with offset control Differential active probes P5205/ P5205A P5210/ P5210A The N2744A T2A adapter supports only the probes listed below with TekProbe interfaces. AC/DC current probe TCP202 50-MHz AC/DC current probe Differential probe, 100 MHz, 50:1/500:1 with offset control (works with InfiniiVision 3000X, 4000X, 6000X, 5000, 6000 and 7000 Series oscilloscopes. Choose P5205 in the listing when you use P5205A) Differential probe, 50 MHz, 100:1/1000:1 with offset control (works with InfiniiVision 3000X, 4000X, 6000X, 5000, 6000 and 7000 Series oscilloscopes. Choose the P5210 in the listing when you use P5210A) P6246 400 MHz, 10:1/1:1 with offset control P6247 1 GHz, 10:1/1:1 with offset control P6248 1.5 GHz, 10:1/1:1 with offset control P6250 500 MHz, 50:1/5:1 with offset control P6251 1 GHz, 50:1/5:1 with offset control Keysight scope compatibility -- Keysight InfiniiVision 3000 X-Series with software version 1.10 or higher -- Keysight InfiniiVision 4000 X- and 6000 X-Series -- Keysight InfiniiVision 5000, 6000, and 7000 Series and future revisions (except 6000 100-MHz) with software version 06.16 or higher -- Keysight Infiniium 9000, V-Series, 90000A/X/Q, Z-Series (with N5442A) Series with software version 03.11 or higher -- Keysight Infiniium S-Series Optical-to-electrical converters (works with InfiniiVision 5000, 6000 and 7000 with version 6.16 software only) P6701B 1 GHz Optical-to-electrical converter with FC/PC connector P6703B 1.2 GHz Optical-to-electrical converter with FC/PC connector P6711 250 MHz Optical-to-electrical converter P6713 300 MHz Optical-to-electrical converter Ordering information N2744A T2A probe interface adapter 55 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet Probing Accessories - N2784A/85A/86A/87A Probe Positioners -- Easy-to-manipulate probe arms for hands-free browsing -- One- or two-articulated arms with stable high-mass base (N2784A and N2785A) -- Quick and stable XY positioning (N2786A) -- Stable 3D probe positioning for hard-to-reach XYZ access -- Compatible with most scope probes -- Applications: Hands-free browsing for electronic components on PC board The N2784A and N2785A probe positioners provide quick and stable X-Y positioning for PC boards and devices that require hands-free probing. Unlike other probe positioners that require multiple adjustments to lock the probe holder into position, the N2784A and N2785A need only the "lift and drop" motion to put the probe in place. The weight stabilization technique used in these probe holders keeps constant pressure at the probing point so the probe tip stays in position even when the target board is bumped. The N2786A is a low cost, easy-to-use XY axis probe holder for general purpose probing applications. The two-leffed positioner is designed to be easy to use-the positioner itself has no controls to positioner it in place. N2786A 2-leg probe positioner The N2787A is a 3D probe positioner with a flexible, articulating arm that can be quickly positioned in a variety of configurations. For more information about Keysight's probe positioners, refer to literature number 5989-9131EN. Ordering information Product number Description N2784A* 1-arm probe positioner N2785A* 2-arm probe positioner N2786A 2-leg probe positioner N2787A 3D probe positioner * Includes 3x magnifying glass, arm strap, cable tie, probe rest, and manual N2784A one-arm probe positioner N2787A 3D probe positioner 56 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet Probing Accessories - Wedge Probe Adapters -- Easy connection to surface mount ICs -- Safe, with no chance of shorting -- Mechanically non-invasive contact -- 3-, 8-, and 16-signal versions -- Supports 0.5 and 0.65mm TQFP and PQFP packages Problem-free probing The Keysight wedge probe adapter eliminates many of the frustrations associated with probing surface mount components. If you've ever accidentally shorted IC pins together, experienced electrical and/or mechanical problems with soldering small wires onto leads, or gotten frustrated juggling multiple probes while you're trying to operate your scope, the Wedge was designed with you in mind. Operating characteristics E26xx Series wedge probe adapters Operating voltage < 40 Vdc + peak ac Operating current 0.5 A maximum Capacitance between contacts 2 pF typical (all except KeysightE2643A/44A) 4.33 pF typical at 1 MHz (KeysightE2643A/44A) Self-inductance 15 nH typical (all except Keysight E2643A/44A) 37 nH typical at 1 MHz (Keysight E2642A/44A) Cross coupling -31 dB typical at 100 MHz (Keysight E2643A/44A) Contact resistance < 0.1 Ordering information Model number Description E2613A 0.5 mm Wedge probe adapter, 3 signal Quantity 1 E2614A 0.5 mm Wedge probe adapter, 8 signal 1 E2643A 0.5 mm Wedge probe adapter, 16 signal 1 Make the inaccessible accessible E2615A 0.65 mm Wedge probe adapter, 3 signal 1 E2616A 0.65 mm Wedge probe adapter, 8 signal 1 When you use the Wedge, you don't have to worry about shorting IC pins together on a delicate component-or worse yet, on an irreplaceable prototype. The Wedge is easy to insert and it stays put. There's no need to solder small wires onto leads. The Wedge is mechanically non-invasive, so you won't damage the legs of the IC. Instead, you'll have easy access to hard-to-reach components. E2644A 0.65 mm Wedge probe adapter, 16 signal 1 10072A SMT kit for 10070 probe family 10075A 0.5 mm IC clip kit Electrical reliability IC clip kits The Wedge makes two contact points with each leg of the IC. This redundant physical connection increases the electrical reliability of the connection. Also the Wedge's low capacitance and inductance provides superior performance to many other alternatives. As an inexpensive solution for probing fine-pitch ICs, the 10072A SMT Kit includes 10 IC clips and 2 dual-lead adapters that connect the clips directly to 10070-family probes. The Wedge probe adapter connects directly to 1145A/1155A active probes and the dual lead adapter provided with the 1160A-65A passive probe family and N2877A/N2879A accessory kits for use with N287xA Series passive probes. The 10075A 0.5mm IC clip kit is ideal for connecting to IC's as fine as 0.5 mm. The clip body allows many clips to be mounted side-by-side. The kit includes four 0.5mm IC clips and two dual-lead adapters that connect the IC clips directly to 10070-family probes. 57 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet Probing Accessories - Fine Pitch and PC Board Accessories 0.5 mm IC clips -- Extremely small size -- Thin body for mounting multiple clips side-by side -- Connection to PQFP and SOIC SMT packages from 0.5 to 0.8 mm (0.020 in. to 0.032 in.) lead pitch Operating characteristics 0.5 IC Clips Length 31.75 mm (1.25 inch) Tip diameter 0.75 mm (0.029 inch) Pin diameter 0.75 mm (0.029 inch) The 0.5 mm IC clips connect directly to the Infiniium MSO logic probe flying leads, N2870A-76A or 1160A-65A passive probe with dual lead adapter, and 1007x passive probe with optional 10072A or 10075A that contain the dual lead adapter. Maximum input voltage is +40 V. Ordering information PC board mini-probe sockets Ordering information -- Hands-free probing of through-hole devices -- Compatible with N2870A-76A and 1160A-65A family probes Part number Description 10467-68701 0.5 mm IC clips -- Allows connection of high impedance probes to the 50 ohm input of Infiniium 54850, 80000 and 90000 Series oscilloscopes -- Includes 500 MHz passive probe (10073D) -- Provides switchable AC/DC coupling as well as 10:1 and 1:1 attenuation settings 4 Extremely small-sized clips for probing PQFP and SOIC SMT packages Part number Description N2766A Horizontal mini-probe socket 25 N2768A Vertical mini-probe socket 25 The PC board mini-probe sockets are ideal for a reliable, convenient, high bandwidth connection between the N2870A-76A and 1160A-65A family passive probe tip, and the circuit under test. E2697A high impedance adapter Quantity Quantity Horizontal and vertical versions of the PC board mini-probe socket make it easy to fit into your target board. Ordering information Part number Description N2697A High impedance adapter Quantity 1 The E2697A high impedance adapter allows connection of probes that require a 1 M high impedance input (e.g., passive probes, current probes) to the Infiniium 54850, 80000 and 90000 Series oscilloscopes. The E2697A high impedance adapter extends the capability of Keysight Infiniium high-performance oscilloscopes, making them ideal for a variety of general-purpose measurements such as power supplies, inverters, semiconductor devices, etc. The E2697A provides switchable AC/DC coupling, as well as 10:1 and 1:1 attenuation settings. Use the N5449A high impedance adapter with Infiniium 90000X and 90000Q Series scopes. 58 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet Related Literature Publication title Publication type Publication number Keysight Oscilloscope Probes and Accessories Selection Guide 5989-6162EN InfiniiVision Oscilloscope Probes and Accessories Data Sheet 5968-8153EN 8 Hints for Better Scope Probing Application Note 5989-7894EN Oscilloscope Probing for High-Speed Signals Application Note 5989-9177EN Performance Comparison of Differential and Single-ended Active Voltage Probes Application Note 5988-8006EN Improving Usability and Performance in High-Bandwidth Active Oscilloscope Probes Application Note 5988-8005EN Optimizing Oscilloscope Measurement Accuracy on High-Performance Systems with Keysight Active Probes Application Note 5988-5021EN Restoring Confidence in Your High-Bandwidth Probe Measurements Application Note 5988-7951EN The Truth About the Fidelity of High-Bandwidth Voltage Probes Application Note 5988-6515EN Extending the Range of Keysight InfiniiMax Probes Application Note 5989-7587EN Understanding and Using Offset in InfiniiMax Active Probes Application Note 5988-9264EN Tips for Making Low Current Measurements with an Oscilloscope and Current Probe Application Note 5989-7529EN Using Keysight InfiniiMax Probes with Test Equipment Other Than Oscilloscopes Application Note 5989-1869EN Why Oscilloscope Measurements may Require Extreme Probing Application Note 5990-4721EN Side by Side Comparison of Keysight and Tektronix Probing Application Note 5989-0553EN Tips and Techniques for Making Power Supply Noise Measurements with an Oscilloscope Application Note 5989-6755EN Time-Domain Response of Keysight InfiniiMax Probes Application Note 5988-9608EN How Offset, Dynamic Range and Compression Affect Measurements Application Note 5990-8255EN Keysight InfiniiMax Probes Impact on Lead-Free (ROHS) Compliance Application Note 5989-5179EN 59 | Keysight | Infiniium Oscilloscope Probes and Accessories - Data Sheet myKeysight www.keysight.com/find/mykeysight A personalized view into the information most relevant to you. www.axiestandard.org AdvancedTCA(R) Extensions for Instrumentation and Test (AXIe) is an open standard that extends the AdvancedTCA for general purpose and semiconductor test. Keysight is a founding member of the AXIe consortium. ATCA(R), AdvancedTCA(R), and the ATCA logo are registered US trademarks of the PCI Industrial Computer Manufacturers Group. www.lxistandard.org LAN eXtensions for Instruments puts the power of Ethernet and the Web inside your test systems. Keysight is a founding member of the LXI consortium. www.pxisa.org PCI eXtensions for Instrumentation (PXI) modular instrumentation delivers a rugged, PC-based high-performance measurement and automation system. Three-Year Warranty www.keysight.com/find/ThreeYearWarranty Keysight's commitment to superior product quality and lower total cost of ownership. The only test and measurement company with three-year warranty standard on all instruments, worldwide. Keysight Assurance Plans www.keysight.com/find/AssurancePlans Up to five years of protection and no budgetary surprises to ensure your instruments are operating to specification so you can rely on accurate measurements. www.keysight.com/go/quality Keysight Technologies, Inc. DEKRA Certified ISO 9001:2008 Quality Management System Keysight Channel Partners www.keysight.com/find/channelpartners Get the best of both worlds: Keysight's measurement expertise and product breadth, combined with channel partner convenience. www.keysight.com/find/probe For more information on Keysight Technologies' products, applications or services, please contact your local Keysight office. The complete list is available at: www.keysight.com/find/contactus Americas Canada Brazil Mexico United States (877) 894 4414 55 11 3351 7010 001 800 254 2440 (800) 829 4444 Asia Pacific Australia China Hong Kong India Japan Korea Malaysia Singapore Taiwan Other AP Countries 1 800 629 485 800 810 0189 800 938 693 0124 229 2010 0120 (421) 345 080 769 0800 1 800 888 848 1 800 375 8100 0800 047 866 (65) 6375 8100 Europe & Middle East Austria Belgium Finland France Germany Ireland Israel Italy Luxembourg Netherlands Russia Spain Sweden Switzerland United Kingdom 0800 001122 0800 58580 0800 523252 0805 980333 0800 6270999 1800 832700 1 809 343051 800 599100 +32 800 58580 0800 0233200 8800 5009286 800 000154 0200 882255 0800 805353 Opt. 1 (DE) Opt. 2 (FR) Opt. 3 (IT) 0800 0260637 For other unlisted countries: www.keysight.com/find/contactus (BP-02-06-15) This information is subject to change without notice. (c) Keysight Technologies, 2012 - 2015 Published in USA, May 15, 2015 5968-7141EN www.keysight.com