1
CSM_E3JM_E3JK_DS_E_10_1
Built-in Power Supply Photoelectric Sensor
E3JM/E3JK
Two Models Contribute to
Overall Cost Reduction
• Easy to wire and adjust.
• Slim body is economically priced and
full of functions.
E3JM Terminal Block Models
E3JK Pre-wired Models
Be sure to read Safety Precautions on
page 10.
Ordering Information
Sensors (Refer to Dimensions on page 12.)
E3JM
* Through-beam Sensors are sold in sets that include both the Emitter and Receiver.
Sensing
method Appearance Connection
method Sensing distance Operation
mode
Output
configuration
Functions Model
Through-
beam
(Emitter +
Receiver) *
Terminal
block
Light-ON
Dark-ON
(switch
selectable)
Relay --- E3JM-10M4-N
E3JM-10M4T-N
DC SSR --- E3JM-10S4-N
E3JM-10S4T-N
Retro-
reflective
with MSR
function E39-R1 (provided)
Relay --- E3JM-R4M4
E3JM-R4M4T
DC SSR --- E3JM-R4S4
E3JM-R4S4T
Diffuse-
reflective
Relay --- E3JM-DS70M4
E3JM-DS70M4T
DC SSR --- E3JM-DS70S4
E3JM-DS70S4T
Red li
g
ht Infrared li
g
ht
10 m
Timer
Timer
4 m Timer
Timer
700 mm Timer
Timer
2
E3JM/E3JK
E3JK
Note: UL-listed models have the -US suffix. Through-beam models have -US suffix instead of -N suffix. (Example: E3JM-10M4-US 2M). Tightening nuts, washers, and
rubber bushings are not provided with these models.
Change: Shape of the E3JM conduit socket
Note, however, that DC-type E3JK SSR Output Models are not UL-listed.
*1. Through-beam Sensors are sold in sets that include both the Emitter and Receiver.
*2. Values in parentheses indicate the sensing distance when using E39-R2 Reflectors.
Accessories (Order Separately)
Slit (A Slit is not provided with the Sensor for through-beam. Order a Slit separately if required.) (Refer to Dimensions on page 12.)
Reflectors (A Reflector is required for Retroreflective Sensors.)
A Reflector is provided with the E39-R1 Sensor. For other Sensors, order a Reflector separately if required.
(Refer to Dimensions on E39-L/F39-L/E39-S/E39-R.)
Note: 1. When using any reflector other than the provided one, use a sensing distance of approximately 0.7 times the typical value as a guide.
2. Refer to Reflectors on E39-L/F39-L/E39-S/E39-R for details.
* Values in parentheses are the minimum required distance between the Sensor and Reflector.
Sensing
method Appearance Connection
method Sensing distance Operation mode
Output
configuration
Model
Through-
beam
(Emitter +
Receiver) *1
Pre-wired
(2 m)
Light-ON Relay E3JK-5M1-N 2M
Dark-ON E3JK-5M2-N 2M
Light-ON
Dark-ON
Both
selectable DC SSR E3JK-5S3-N 2M
Retro-reflec-
tive with MSR
function
E39-R1
(provided)
*2Light-ON Relay E3JK-R2M1 2M
Dark-ON E3JK-R2M2 2M
Light-ON
Dark-ON
Both
selectable DC SSR E3JK-R2S3 2M
Retro-reflec-
tive without
MSR function
*2Light-ON Relay E3JK-R4M1 2M
Dark-ON E3JK-R4M2 2M
Light-ON
Dark-ON
Both
selectable DC SSR E3JK-R4S3 2M
Diffuse-
reflective
Light-ON Relay E3JK-DS30M1 2M
Dark-ON E3JK-DS30M2 2M
Light-ON
Dark-ON
Both
selectable DC SSR E3JK-DS30S3 2M
Slit width Sensing distance
Minimum detect-
able object
(typical)
Model Quantity Remarks
1 mm × 20 mm
E3JM-10@4(T)-N 1.2 m
1-mm dia. E39-S39
1 Slit each for
the Emitter and
Receiver (2 Slits
total)
(Seal-type long slit)
Can be used with the E3JM-10@4(T)-N
and E3JK-5@@-N Through-beam
Models.
E3JK-5@@-N 0.7 m
Name Sensing distance (typical) Model Quantity Remarks
Reflectors
E3JM-R4@4(T) 4 m (rated value)
E39-R1 1
Provided with the E3JM-R4@4(T)
Provided with the E3JK-R2@@
Provided with the E3JK-R4@@
E3JK-R2@@ 2.5 m (rated value)
E3JK-R4@@ 4 m (rated value)
E3JK-R2@@ 3 m E39-R2 1 ---
E3JK-R4@@ 5 m
Small Reflectors E3JM-R4@4(T) 3.5 m E39-R3 1 ---
E3JK-R2@@ 1 m (5 mm) *
Tape Reflectors
E3JM-R4@4(T) 1 m (200 mm) *E39-RS1 1
Enables MSR function.
E3JK-R2@@ 750 mm (200 mm) *
E3JM-R4@4(T) 1.6 m (200 mm) *E39-RS2 1
E3JK-R2@@ 1.2 m (200 mm) *
E3JM-R4@4(T) 2 m (200 mm) *E39-RS3 1
E3JK-R2@@ 1.5 m (200 mm) *
5 m
2.5 m
(3 m)
4 m
(5 m)
300 mm
3
E3JM/E3JK
Mounting Bracket
Some Mounting Brackets are provided with the Sensor. Order other Mounting Brackets separately if required.
(Refer to E39-L/F39-L/E39-S/E39-R)
Note: 1. When using a Through-beam Sensor, order one Connector for the Receiver and one for the Emitter.
2. Refer to Mounting Brackets on E39-L/F39-L/E39-S/E39-R for details.
Appearance Model Quantity Remarks
E39-L53 1 Provided with the E3JM.
E39-L40 1 Provided with the E3JK.
E39-L51 1
Mounting Bracket designed for changing
from he E3A-M, E3A2, E3A3, OA-5, or
OA-5N to the E3JM.
4
E3JM/E3JK
Ratings and Specifications
E3JM
* The timer cannot be disabled for models with timer functions (E3JM-@@@4T).
Sensing method Through-beam model Retro-reflective model
(with MSR function) Diffuse-reflective model
Item Model E3JM-10@4(T)-N E3JM-R4@4(T) E3JM-DS70@4(T)
Sensing distance 10 m 4 m (When using E39-R1) White paper (200 × 200 mm):
700 mm
Standard sensing object Opaque: 14.8-mm dia. min. Opaque: 75-mm dia. min. ---
Differential travel --- 20% max. of sensing distance
Directional angle Both Emitter and Receiver 3° to
20°1° to 5°---
Light source (wavelength) Infrared LED (950 nm) Red LED (660 nm) Infrared LED (950 nm)
Power supply voltage 12 to 240 VDC±10%, ripple (p-p): 10% max.
24 to 240 VAC±10%, 50/60 Hz
Power con-
sumption
DC 3 W max. (Emitter 1.5 W max.
Receiver 1.5 W max.) 2 W max.
AC 3 W max. (Emitter 1.5 W max.
Receiver 1.5 W max.) 2 W max.
Control output
Relay output (E3JM-@@M4 (T) model): SPDT, 250 VAC, 3A (cosφ=1) max., 5 VDC, 10 mA min.
DC SSR output (E3JM-@@S4 (T) model): 48 VDC, 100 mA max. (residual voltage: 2 V max.)
Light-ON/Dark-ON selectable
Life
expectancy
(relay output)
Mechanical 50,000,000 times min. (switching frequency: 18,000 times/h)
Electrical 100,000 times min. (switching frequency: 1,800 times/h)
Response time Relay output (E3JM-@@M4 (T) models) Operate or reset: 30 ms max.
DC SSR output (E3JM-@@S4 (T) models) Operate or reset: 5 ms max.
Sensitivity adjustment --- One-turn adjuster
Timer function *ON-delay/OFF-delay/One-shot delay switch selectable
Delay time: 0.1 to 5 s (adjustable), only for E3JM-@@@4T
Ambient illumination
(Receiver side) Incandescent lamp: 3,000 lx max.
Ambient temperature range Operating: −25°C to 55°C, Storage: −30°C to 70°C (with no icing or condensation)
Ambient humidity range Operating: 45% to 85% (with no condensation), Storage: 35% to 95% (with no condensation)
Insulation resistance 20 MΩ min. at 500 VDC
Dielectric strength 2,000 VAC, 50/60 Hz for 1 min.
Vibration
resistance
Destruction 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Malfunction 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock
resistance
Destruction 500 m/s2 3 times each in X, Y, and Z directions
Malfunction 100 m/s2 3 times each in X, Y, and Z directions
Degree of protection IEC 60529: IP66
Connection method Terminal block
Weight (packed state) Approx. 270 g Approx. 160 g
Material
Case ABS (Acrylonitril Butadiene Styrene)
Lens Methacrylic resin
Cover Polycarbonate
Mounting
Bracket Iron
Accessories Mounting Bracket (with screw), Nuts, Terminal Protection Cover, One set of cable connection nuts (exclud-
ing -US Models), Instruction manual, Reflector (E39-R1: only for Retro-reflective Sensors)
5
E3JM/E3JK
E3JK
Sensing method Through-beam model Retro-reflective model
(with MSR function)
Retro-reflective model
(without MSR function) Diffuse-reflective model
Item Model E3JK
-5M@-N
E3JK
-5S3-N
E3JK
-R2M@E3JK
-R2S3
E3JK
-R4M@E3JK
-R4S3
E3JK
-DS30M@E3JK
-DS30S3
Sensing distance 5 m 2.5 m (When using E39-R1) 4 m (When using E39-R1) White paper (100 × 100 mm):
300 mm
Standard sensing
object Opaque: 14.8-mm dia. min. Opaque: 75-mm dia. min. ---
Differential travel --- 20% max. of sensing distance
Directional angle Both Emitter and Receiver 3° to
20°1° to 5°---
Light source
(wavelength) Infrared LED (950 nm) Red LED (660 nm) Infrared LED (950 nm)
Power supply
voltage
12 to 240 VDC±10%, ripple (p-p): 10% max.
24 to 240 VAC±10%, 50/60 Hz
Power
con-
sump-
tion
DC 3 W max. (Emitter 1.5 W
max. Receiver 1.5 W max.) 2 W max.
AC 3 W max. (Emitter 1.5 W
max. Receiver 1.5 W max.) 2 W max.
Control output
Relay output
SPDT,
250 VAC, 3 A
max.
(cosφ= 1)
5 VDC, 10 mA
min.
DC SSR out-
put, Negative:
common
48 VDC,
100 mA max.
Leakage cur-
rent: 0.1 mA
max.
With load
short-circuit
protection
Relay output
SPDT,
250 VAC, 3 A
max.
(cosφ= 1)
5 VDC, 10 mA
min.
DC SSR out-
put, Negative:
common
48 VDC,
100 mA max.
Leakage cur-
rent: 0.1 mA
max.
With load
short-circuit
protection
Relay output
SPDT,
250 VAC, 3 A
max.
(cosφ= 1)
5 VDC, 10 mA
min.
DC SSR out-
put, Nega-
tive: common
48 VDC,
100 mA max.
Leakage cur-
rent: 0.1 mA
max.
With load
short-circuit
protection
Relay output
SPDT,
250 VAC, 3 A
max.
(cosφ= 1)
5 VDC, 10 mA
min.
DC SSR out-
put, Negative:
common
48 VDC,
100 mA max.
Leakage cur-
rent: 0.1 mA
max.
With load
short-circuit
protection
Life ex-
pectan-
cy (relay
output)
Mechani-
cal 50,000,000 times min. (switching frequency: 18,000 times/h)
Electrical 100,000 times min. (switching frequency: 1,800 times/h)
Response time 30 ms max. 10 ms max. 30 ms max. 5 ms max. 30 ms max. 5 ms max. 30 ms max. 5 ms max.
Sensitivity
adjustment --- One-turn adjuster
Ambient illumina-
tion
(Receiver side)
Incandescent lamp: 3,000 lx max.
Ambient
temperature range Operating: −25°C to 55°C, Storage: −30°C to 70°C (with no icing or condensation)
Ambient
humidity range Operating: 45% to 85% (with no condensation), Storage: 35% to 95% (with no condensation)
Insulation
resistance 20 MΩ min. at 500 VDC
Dielectric strength 1,500 VAC, 50/60 Hz for 1 min.
Vibra-
tion re-
sistance
Destruc-
tion 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Malfunc-
tion 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock
resis-
tance
Destruc-
tion 500 m/s2 3 times each in X, Y, and Z directions
Malfunc-
tion
100 m/s2 3
times each in
X, Y, and Z di-
rections
500 m/s2 3
times each in
X, Y, and Z di-
rections
100 m/s2 3
times each in
X, Y, and Z di-
rections
500 m/s2 3
times each in
X, Y, and Z di-
rections
100 m/s2 3
times each in
X, Y, and Z di-
rections
500 m/s2 3
times each in
X, Y, and Z di-
rections
100 m/s2 3
times each in
X, Y, and Z di-
rections
500 m/s2 3
times each in
X, Y, and Z di-
rections
Degree of
protection IEC 60529 IP64
Connection method Pre-wired (standard length: 2 m)
Weight
(packed state) Approx. 420 g Approx. 250 g
Material
Case ABS (Acrylonitril Butadiene Styrene)
Lens Methacrylic resin
Mounting
Bracket
Iron
Accessories Mounting Bracket (with screws), Nuts, Instruction manual, Reflector (Retro-reflective Models only)
6
E3JM/E3JK
Engineering Data (Typical)
Parallel Operating Range
Through-beam Through-beam Retro-reflective
E3JM-10@4(T)-N
E3JM-10
@
4(T)-N + E39-S39 (Optional Slit)
(A Slit is mounted to the Emitter and Receiver.)
E3JM-R4@4(T) + E39-R1
(Supplied Reflector)
Operating Range
Diffuse-reflective
E3JM-DS70@4(T)
Excess Gain Ratio vs. Set Distance
Through-beam Retro-reflective
E3JM-10@4(T)-N E3JM-R4@4(T) + E39-R1
(Supplied Reflector)
E3JM-R4@4(T) + E39-R3
(Optional Reflector)
600
400
200
0
−200
−400
−600
2 4 6 8 10 12 14 16
Distance X (m)
Y
X
Distance Y (mm)
60
40
20
0
−20
−40
−60
0.5 1 1.5 2 2.5 3 3.5
Y
X
Distance
X (m)
Distance Y (mm)
150
100
50
0
−50
−100
−150
12
Reflector: E39-R1
345678
Y
X
Distance
X (m)
Distance Y (mm)
60
50
40
30
20
10
0
−10
−20
−30
−40
−50
−60
24 6 810
White paper
Black carbon
SUS (Luster)
Aluminum foil
(No luster on
the back)
Sensing object: 200 × 200 mm
Y
X
Distance
X (m)
Distance Y (mm)
1,000
500
100
50
10
5
1
0.5
0.1
Distance
(
m
)
20 4 6 8 10 12 14 16 18
Operating
level
Excess gain ratio
1,000
500
100
50
10
5
1
0.5
0.1
1023456789
Reflector: E39-R1
Distance
(
m
)
Operating
level
Excess gain ratio
1,000
500
300
100
50
30
10
5
3
1
0.5
0.3
0.1
1023456789
Reflector: E39-R3
Distance
(
m
)
Operating
level
Excess gain ratio
7
E3JM/E3JK
Diffuse-reflective
Sensing Object Size vs. Sensing Distance
E3JM-DS70@4(T) E3JM-DS70@4(T)
Parallel Operating Range
Through-beam
E3JK-5@@-N E3JK-5@@-N + E39-S39 (Optional Slit)
(A Slit is mounted to the Emitter and Receiver.)
Retro-reflective
E3JK-R2@@ + E39-R1
(Supplied Reflector)
E3JK-R4@@ + E39-R1
(Supplied Reflector)
1,000
500
100
50
10
5
1
0.5
0.1
Distance
(
mm
)
1000 200 300 400 500 600 700 800 900
Operating
level
Sensing object:
white paper 200 × 200 mm
Excess gain ratio
12
10
8
6
4
2
20
0
40 60 80 100 120 140 160 180 200 220
Side len
g
th of sensin
g
ob
j
ect
(
mm
)
White paper
Black carbon
SUS (Luster)
Aluminum foil
(No luster on
the back)
Distance (m)
600
400
200
0
−200
−400
−600
1234567
Distance X (mm)
Distance Y (mm)
Y
X
30
20
10
0
−10
−20
−30
0.5 1 1.5 2
Y
X
Distance
X (mm)
Distance Y (mm)
150
100
50
0
−50
−100
−150
1234
Reflector: E39-R1
Y
X
Distance
X (mm)
Distance Y (mm)
150
100
50
0
−50
−100
−150
123456
Y
X
Reflector: E39-R1
Distance Y (mm)
Distance X (m)
8
E3JM/E3JK
Operating Range Sensing Object Size vs. Sensing Distance
Diffuse-reflective Diffuse-reflective
E3JK-DS30@@ E3JK-DS30@@
Excess Gain Ratio vs. Set Distance
Through-beam Retro-reflective
E3JK-5@@-N E3JK-R2@@ + E39-R1 (Supplied Reflector)
Diffuse-reflective
E3JK-R4
@@
+ E39-
R1
(Supplied Reflector)
E3JK-DS30@@
50
40
30
20
10
0
−10
−20
−30
−40
−50
123
4
Distance (m)
White paper
Black carbon
SUS (Luster)
Aluminum foil
(No luster on
the back)
Sensing object: 100 × 100 mm
Distance (m)
Y
X
5
4
3
2
1
100 2030405060708090
100 110
Side len
g
th of sensin
g
object (mm)
White paper
Black carbon
SUS (Luster)
Aluminum foil
(No luster on
the back)
Distance (m)
1,000
500
300
100
50
30
10
5
3
1
Distance (m)
102345678
Operating
level
Excess gain ratio
100
50
30
10
5
3
1
10234
Reflector: E39-R1
Distance (m)
Operating
level
Excess gain ratio
102345
100
50
30
10
5
3
1
Reflector: E39-R1
Distance (m)
Operating
level
Excess gain ratio
1000 200 300 400 500
100
50
30
10
5
3
1
Distance (mm)
Operating
level
Excess gain ratio
Sensing object: 100 × 100 mm
9
E3JM/E3JK
I/O Circuit Diagrams
E3JM
Relay Output Models
DC SSR Output Models
Note: Connect terminal 1 to any polarity and terminal 2 to the power supply because there is no polarity on the Emitter side.
* Models numbers for Through-beam Sensors (E3JM-10@4(T)-N) are for sets that include both the Emitter and Receiver.
E3JK
Relay Output Models
DC SSR Output Models
Note: Connect the brown cable to any polarity and the blue cable to the power supply because there is no polarity on the Emitter side.
* Models numbers for Through-beam Sensors (E3JK-5@@-N 2M) are for sets that include both the Emitter and Receiver.
Model Timing chart Output circuit
E3JM-10M4(T)-N *
E3JM-R4M4(T)
E3JM-DS70M4(T)
Light indicator
(red)
L-ON (Ta)
D-ON (Ta)
Incident light
No incident light
ON
OFF
ON
OFF
ON
OFF
1
2
4
5
3
No polarity
24 to 240 VAC
12 to 240 VDC
Tb
Tc Contact output
Ta
(Built-in Relay: G6C)
Photoelectric
Sensor main
circuit
Power
Source
Model Timing chart Output circuit
E3JM-10S4(T)-N *
E3JM-R4S4(T)
E3JM-DS70S4(T)
Model Timing chart Output circuit
E3JK-5M1-N *
E3JK-5M2-N *
E3JK-R2M1
E3JK-R2M2
E3JK-R4M1
E3JK-R4M2
E3JK-DS30M1
E3JK-DS30M2
Light indicator
(red)
L-ON (Ta)
D-ON (Ta)
Incident light
No incident light
ON
OFF
ON
OFF
ON
OFF
1
2
3
5
4
Drive
Circuit
Drive
Circuit
L/ON
D/ON
NO
NC
48 VDC
max.
COM
Load
Load
I1
I2
I1+I2<100 mA
No polarity
24 to 240 VAC
12 to 240 VDC
Photo-
electric
Sensor
main
circuit
Power
Source
Light indicator
(red)
L-ON (Ta)
(E3JK-@@M1)
D-ON (Ta)
(E3JK-@@M2)
Incident light
No incident light
ON
OFF
ON
OFF
ON
OFF
White
Brown
Blue
Black
Tc
TbTa Gray
No polarity
24 to 240 VAC
12 to 240 VDC
Contact output
(Built-in Relay: G6C)
Photoelectric
Sensor main
circuit
Power
source
Model Timing chart Output circuit
E3JK-5S3-N *
E3JK-R2S3
E3JK-R4S3
E3JK-DS30S3
Light indicator
(red)
L-ON output
D-ON output
Incident light
No incident light
ON
OFF
ON
OFF
ON
OFF
Drive
Circuit
Drive
Circuit
48 VDC
max.
Load
Load
I1+I2<100 mA
No polarity
24 to 240 VAC
12 to 240 VDC
Photo-
electric
Sensor
main
circuit
Power
Source
D/ON
L/ON
Gray
Black
White
I1
I2
Brown
Blue
Note: The output stage leakage currents are 0.1 mA max., respectively.
10
E3JM/E3JK
Safety Precautions
Refer to Warranty and Limitations of Liability.
This product is not designed or rated for ensuring
safety of persons either directly or indirectly.
Do not use it for such purposes.
Do not use the product in atmospheres or environments that exceed
product ratings.
● Designing
Operation Note: The white part of the DIP switch indicates which setting is selected.
Output Relay Contact
If E3JM/E3JK is connected to a load with contacts that spark when the load is turned OFF (e.g., a contactor or valve), the normally-closed side
may be turned ON before the normally-open side is turned OFF or vice-versa. If both normally-open output and normally-closed output are used
simultaneously, apply an surge suppressor to the load.
Refer to OMRON’s PCB Relays Catalog (X33) for typical examples of surge suppressors.
WARNING
Precautions for Correct Use
E3JM
Switch
configuration Switch selection Timing charts
Models
without
timer
Models
with
timer
ON-delay OFF-delay One-shot delay ON-delay OFF-delay One-shot delay
Note: The operation selector is the same as that for models
without a timer.
MODE
0 1
D·ON L·ON
Operation
selector
D·ON L·ON
Dark-ON, Relay ON
DC output switching
element ON
D·ON L·ON
Light-ON, Relay ON,
DC output switching
element ON
MODE
0 1
MODE
0 1
Incident light
No incident light
ON
OFF
ON
OFF
L
·
ON
D
·
ON
MODE
0 1
D·ON L·ON
SW1
SW2
TIMER
Operation
Selector
Selector switch for
timer mode
MODE
0 1
D·ON
L
·
ON
SW1
SW2
TIMER
Both SW1 and
SW2 at "0."
MODE
0 1
D·ON
L
·
ON
SW1
SW2
TIMER
Onl
y
SW2 at "1."
MODE
0 1
D·ON
L
·
ON
SW1
SW2
TIMER
Only SW1 at "1,"
which overrides either
setting of SW2.
L·ON
D·ON
T
T
Incident light
No incident light
ON
OFF
ON
OFF
L·ON
D·ON
T
T
Incident light
No incident light
ON
OFF
ON
OFF
L
·
ON
D
·
ON
T
T
Incident light
No incident light
ON
OFF
ON
OFF
11
E3JM/E3JK
● Wiring
Connecting and Wiring
•We recommend connecting a cable with a conductor cross-section
of 0.3 mm2 and an outer diameter of 6 to 8 mm.
•Be sure to firmly tighten the cover in order to maintain waterproof
and dustproof properties. The screw size of the conduit sockets is
shown in the following table.
Cable End Treatment
Recommended Crimp Terminal Dimensions (Unit: mm)
Note: Use terminals with insulation tube (recommended crimp terminal: 1.25 to
3.5).
● Others
Terminal Protection Cover (Provided)
The terminal protection cover is designed to improve safety by
maintaining the sensitivity properties of the product and by preventing
any contact with charged sections while it is being operated with the
mode set to the timer mode. Mount the product as shown in the
following diagram (mount the Through-beam Model on the Receiver
side).
● Designing
Power Reset Time
The Sensor is ready to detect within 200 ms after it is turned ON. If
the Sensor and load are connected to separate power supplies, be
sure to turn ON the Sensor first.
● Wiring
Connecting and Wiring DC SSR Output Models
When using the DC SSR output model, the total of the load current for
the Light-ON output (NO) and that for the Dark-ON (NC) should be
100 mA max. If the total exceeds 100 mA, the load short-circuit
protection function will be activated (this function will be reset when
the power of the Photoelectric Sensor is turned OFF).
● Others
Ambient Conditions (Installation Area)
The E3JM will malfunction if installed in the following places.
•Places where the E3JM is exposed to a dusty environment.
•Places where corrosive gases are produced.
•Places where the E3JM is directly exposed to water, oil, or
chemicals.
Model Conduit socket thread size
E3JM-@PF1/2
Round type Fork type
Power
source
Tc, Ta
Tb
Approx.
45 mm
Approx.
55 mm Ti
htenin
nut
rovided
*
Washer (provided)*
Rubber bushing (provided)*
Adjust the four wires to the same length when
the Ta output is to be used only. If both the Ta
and Tb outputs are to be used, treat them as
shown in the following diagram.
Recommended example
* These parts are not provided with models with a -US suffix.
10 max.
19 max.
3.6 dia. min.
7 max.7 max.
(After crimping)
10 max.
19 max.
3.6 dia. min.
7 max.7 max.
(After crimping)
Terminal protection cove
r
E3JM
E3JK
Items Common to
E3JM and E3JK
Emitter
Receiver
Emitter
Receiver
12
E3JM/E3JK
Dimensions
Sensors
*1. Models numbers for Through-beam Sensors (E3JM-10@4(T)-N) are for sets that include both the Emitter and Receiver.
*2. Models numbers for Through-beam Sensors (E3JK-5@@-N) are for sets that include both the Emitter and Receiver.
Accessories (Order separately)
(Unit: mm)
Tolerance class IT16 applies to dimensions in this datasheet unless otherwise specified.
E3JM-10@4(T)-N *1
22 6.4
6
24.5
8
12.4 6 dia. 18 6
(12.4)6
39.5
40
5
JIS
B 0202
PF1/2
Hexagonal nut
(Diagonal: 22)
Applicable cable:
6 to 8 dia.
65
Indicator *1
75
11.5
3
20
80
65
25
4.1
Lens: 14.8 dia.
15
*1. Emitter: Power indicator
Receiver: Light indicator (without timer function
)
Operation indicator (with timer function)
*2. Mounting Brackets can be used on the A side.
44 9
Two, M4×30
1.6
Steel 54.5
(A) *2
Optical axis
42
Two, M6
With Mounting Bracket Attached
Mounting Holes
Note: The operating mode switch and timer
mode switch are located inside the cover.
Note: The operating mode switch, timer mode switch, and
sensitivity adjuster (sensitivity adjuster: E3JM-
DS70@4(T) only) are located inside the cover.
22 6.4
6
24.5
8
12.4 18 6
(12.4)6
39.5
40
5
JIS
B 0202
PF1/2
65
75
11.5
3
20
80
65
25
4.1
15
47.5
Receiver
9
1.6
54.5
42
6 dia.
Hexagonal nut
(Diagonal: 22)
Applicable cable:
6 to 8 dia.
Indicator *1
Emitter
*1. Light indicator (without timer function)
Operation indicator (with timer function)
*2. Mounting Brackets can be used on the A side.
Two, M4 × 30
Steel
(A) *2
Two, M6
E3JM-R4@4(T)
E3JM-DS70@4(T)
With Mounting Bracket Attached
Mounting Holes
21
12
42
50
40
58
10°
R56.6
40
5
36.5
21.5
13.4
28
50
18
60
49 18
7
6.4
22
40 12
6.4
*1. Mounting Brackets can be used on the A side
(M4 × 20 screws: 2 sets provided)
*2. Emitter: Power indicator
Receiver: Light indicator
*3. The Emitter has two conductors.
42
6-dia. vinyl-insulated round
cable with 5 conductors
(Conductor cross section: 0.3 mm2,
Insulator diameter: 1.5 mm),
Standard length: 2 m *3
6 dia.
Indicator *2
Lens: 14.8 dia.
Steel
(A) *1
Optical axis
Two, M6
E3JK-5@@-N *2
Mounting Holes
With Mounting Bracket Attached
21
12
Sensitivity adjuster *2
42
50
40
58
10°
R56.6
40
5
Optical
axis
40
25
Steel
13.4
28
50
Lens
Light indicator
18
60
49 18
6 dia.
7
6.4
22
40 12
6.4
Emitter
Receiver
*1. Mounting Brackets can be used on the A side
(M4 × 20 screws: 2 sets provided)
*2. Sensitivity adjusters are not available on
Retro-reflective models.
(A) *1
42
Two, M6
6-dia. vinyl-insulated round
cable with 5 conductors
(Conductor cross section: 0.3 mm2,
Insulator diameter: 1.5 mm),
Standard length: 2 m
E3JK-R2@@
E3JK-R4@@
E3JK-DS30@@ With Mounting Bracket Attached
Mounting Holes
Seal-type Long Slit (For E3JM/E3JK) Mounting Brackets
Refer to E39-L/F39-L/E39-S/E39-R for details.
E39-S39
Materials: Polyester
0.1-mm thick
14
20 26.5
1±0.1
Read and Understand This Catalog
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or
comments.
Warranty and Limitations of Liability
WARRANTY
OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified)
from date of sale by OMRON.
OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR
FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS
DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED.
LIMITATIONS OF LIABILITY
OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS
IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT
LIABILITY.
In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted.
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS
OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT
SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR.
Application Considerations
SUITABILITY FOR USE
OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's
application or use of the products.
At the customer's request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the
products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product,
machine, system, or other application or use.
The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible
uses of the products, nor is it intended to imply that the uses listed may be suitable for the products:
Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog.
Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles,
safety equipment, and installations subject to separate industry or government regulations.
Systems, machines, and equipment that could present a risk to life or property.
Please know and observe all prohibitions of use applicable to the products.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE
SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND
INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
PROGRAMMABLE PRODUCTS
OMRON shall not be responsible for the user's programming of a programmable product, or any consequence thereof.
Disclaimers
CHANGE IN SPECIFICATIONS
Product specifications and accessories may be changed at any time based on improvements and other reasons.
It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made.
However, some specifications of the products may be changed without any notice. When in doubt, special model numbers may be assigned to fix or
establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual
specifications of purchased products.
DIMENSIONS AND WEIGHTS
Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown.
PERFORMANCE DATA
Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the
result of OMRON’s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON
Warranty and Limitations of Liability.
ERRORS AND OMISSIONS
The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical,
typographical, or proofreading errors, or omissions.
2012.3
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2012 All Right Reserved.
Terms and Conditions of Sale
1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed
part of all quotes, agreements, purchase orders, acknowledgments, price lists,
catalogs, manuals, brochures and other documents, whether electronic or in
writing, relating to the sale of products or services (collectively, the "Products")
by Omron Electronics LLC and its subsidiary companies (“Omron”). Omron
objects to any terms or conditions proposed in Buyer’s purchase order or other
documents which are inconsistent with, or in addition to, these Terms.
2. Prices; Payment Terms. All prices stated are current, subject to change with-
out notice by Omron. Omron reserves the right to increase or decrease prices
on any unshipped portions of outstanding orders. Payments for Products are
due net 30 days unless otherwise stated in the invoice.
3. Discounts. Cash discounts, if any, will apply only on the net amount of invoices
sent to Buyer after deducting transportation charges, taxes and duties, and will
be allowed only if (i) the invoice is paid according to Omron’s payment terms
and (ii) Buyer has no past due amounts.
4. Interest. Omron, at its option, may charge Buyer 1-1/2% interest per month or
the maximum legal rate, whichever is less, on any balance not paid within the
stated terms.
5. Orders. Omron will accept no order less than $200 net billing.
6. Governmental Approvals. Buyer shall be responsible for, and shall bear all
costs involved in, obtaining any government approvals required for the impor-
tation or sale of the Products.
7. Taxes. All taxes, duties and other governmental charges (other than general
real property and income taxes), including any interest or penalties thereon,
imposed directly or indirectly on Omron or required to be collected directly or
indirectly by Omron for the manufacture, production, sale, delivery, importa-
tion, consumption or use of the Products sold hereunder (including customs
duties and sales, excise, use, turnover and license taxes) shall be charged to
and remitted by Buyer to Omron.
8. Financial. If the financial position of Buyer at any time becomes unsatisfactory
to Omron, Omron reserves the right to stop shipments or require satisfactory
security or payment in advance. If Buyer fails to make payment or otherwise
comply with these Terms or any related agreement, Omron may (without liabil-
ity and in addition to other remedies) cancel any unshipped portion of Prod-
ucts sold hereunder and stop any Products in transit until Buyer pays all
amounts, including amounts payable hereunder, whether or not then due,
which are owing to it by Buyer. Buyer shall in any event remain liable for all
unpaid accounts.
9. Cancellation; Etc. Orders are not subject to rescheduling or cancellation
unless Buyer indemnifies Omron against all related costs or expenses.
10. Force Majeure. Omron shall not be liable for any delay or failure in delivery
resulting from causes beyond its control, including earthquakes, fires, floods,
strikes or other labor disputes, shortage of labor or materials, accidents to
machinery, acts of sabotage, riots, delay in or lack of transportation or the
requirements of any government authority.
11. Shipping; Delivery. Unless otherwise expressly agreed in writing by Omron:
a. Shipments shall be by a carrier selected by Omron; Omron will not drop ship
except in “break down” situations.
b. Such carrier shall act as the agent of Buyer and delivery to such carrier shall
constitute delivery to Buyer;
c. All sales and shipments of Products shall be FOB shipping point (unless oth-
erwise stated in writing by Omron), at which point title and risk of loss shall
pass from Omron to Buyer; provided that Omron shall retain a security inter-
est in the Products until the full purchase price is paid;
d. Delivery and shipping dates are estimates only; and
e. Omron will package Products as it deems proper for protection against nor-
mal handling and extra charges apply to special conditions.
12. Claims. Any claim by Buyer against Omron for shortage or damage to the
Products occurring before delivery to the carrier must be presented in writing
to Omron within 30 days of receipt of shipment and include the original trans-
portation bill signed by the carrier noting that the carrier received the Products
from Omron in the condition claimed.
13. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the
Products will be free from defects in materials and workmanship for a period of
twelve months from the date of sale by Omron (or such other period expressed
in writing by Omron). Omron disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION,
EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABIL-
ITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS.
BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR
INTENDED USE. Omron further disclaims all warranties and responsibility of
any type for claims or expenses based on infringement by the Products or oth-
erwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obli-
gation hereunder shall be, at Omron’s election, to (i) replace (in the form
originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying
Product, or (iii) repay or credit Buyer an amount equal to the purchase price of
the non-complying Product; provided that in no event shall Omron be responsi-
ble for warranty, repair, indemnity or any other claims or expenses regarding
the Products unless Omron’s analysis confirms that the Products were prop-
erly handled, stored, installed and maintained and not subject to contamina-
tion, abuse, misuse or inappropriate modification. Return of any Products by
Buyer must be approved in writing by Omron before shipment. Omron Compa-
nies shall not be liable for the suitability or unsuitability or the results from the
use of Products in combination with any electrical or electronic components,
circuits, system assemblies or any other materials or substances or environ-
ments. Any advice, recommendations or information given orally or in writing,
are not to be construed as an amendment or addition to the above warranty.
See http://www.omron247.com or contact your Omron representative for pub-
lished information.
14. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE
FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY
WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS
BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual
price of the Product on which liability is asserted.
15. Indemnities. Buyer shall indemnify and hold harmless Omron Companies and
their employees from and against all liabilities, losses, claims, costs and
expenses (including attorney's fees and expenses) related to any claim, inves-
tigation, litigation or proceeding (whether or not Omron is a party) which arises
or is alleged to arise from Buyer's acts or omissions under these Terms or in
any way with respect to the Products. Without limiting the foregoing, Buyer (at
its own expense) shall indemnify and hold harmless Omron and defend or set-
tle any action brought against such Companies to the extent based on a claim
that any Product made to Buyer specifications infringed intellectual property
rights of another party.
16. Property; Confidentiality. Any intellectual property in the Products is the exclu-
sive property of Omron Companies and Buyer shall not attempt to duplicate it
in any way without the written permission of Omron. Notwithstanding any
charges to Buyer for engineering or tooling, all engineering and tooling shall
remain the exclusive property of Omron. All information and materials supplied
by Omron to Buyer relating to the Products are confidential and proprietary,
and Buyer shall limit distribution thereof to its trusted employees and strictly
prevent disclosure to any third party.
17. Export Controls. Buyer shall comply with all applicable laws, regulations and
licenses regarding (i) export of products or information; (iii) sale of products to
“forbidden” or other proscribed persons; and (ii) disclosure to non-citizens of
regulated technology or information.
18. Miscellaneous. (a) Waiver. No failure or delay by Omron in exercising any right
and no course of dealing between Buyer and Omron shall operate as a waiver
of rights by Omron. (b) Assignment. Buyer may not assign its rights hereunder
without Omron's written consent. (c) Law. These Terms are governed by the
law of the jurisdiction of the home office of the Omron company from which
Buyer is purchasing the Products (without regard to conflict of law princi-
ples). (d) Amendment. These Terms constitute the entire agreement between
Buyer and Omron relating to the Products, and no provision may be changed
or waived unless in writing signed by the parties. (e) Severability
. If any provi-
sion hereof is rendered ineffective or invalid, such provision shall not invalidate
any other provision. (f) Setoff. Buyer shall have no right to set off any amounts
against the amount owing in respect of this invoice. (g) Definitions. As used
herein, “including” means “including without limitation”; and “Omron Compa-
nies” (or similar words) mean Omron Corporation and any direct or indirect
subsidiary or affiliate thereof.
Certain Precautions on Specifications and Use
1. Suitability of Use. Omron Companies shall not be responsible for conformity
with any standards, codes or regulations which apply to the combination of the
Product in the Buyer’s application or use of the Product. At Buyer’s request,
Omron will provide applicable third party certification documents identifying
ratings and limitations of use which apply to the Product. This information by
itself is not sufficient for a complete determination of the suitability of the Prod-
uct in combination with the end product, machine, system, or other application
or use. Buyer shall be solely responsible for determining appropriateness of
the particular Product with respect to Buyer’s application, product or system.
Buyer shall take application responsibility in all cases but the following is a
non-exhaustive list of applications for which particular attention must be given:
(i) Outdoor use, uses involving potential chemical contamination or electrical
interference, or conditions or uses not described in this document.
(ii) Use in consumer products or any use in significant quantities.
(iii) Energy control systems, combustion systems, railroad systems, aviation
systems, medical equipment, amusement machines, vehicles, safety equip-
ment, and installations subject to separate industry or government regulations.
(iv) Systems, machines and equipment that could present a risk to life or prop-
erty. Please know and observe all prohibitions of use applicable to this Prod-
uct.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT
ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
ADDRESS THE RISKS, AND THAT THE OMRON’S PRODUCT IS PROP-
ERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
2. Programmable Products. Omron Companies shall not be responsible for the
user’s programming of a programmable Product, or any consequence thereof.
3. Performance Data. Data presented in Omron Company websites, catalogs
and other materials is provided as a guide for the user in determining suitabil-
ity and does not constitute a warranty. It may represent the result of Omron’s
test conditions, and the user must correlate it to actual application require-
ments. Actual performance is subject to the Omron’s Warranty and Limitations
of Liability.
4. Change in Specifications. Product specifications and accessories may be
changed at any time based on improvements and other reasons. It is our prac-
tice to change part numbers when published ratings or features are changed,
or when significant construction changes are made. However, some specifica-
tions of the Product may be changed without any notice. When in doubt, spe-
cial part numbers may be assigned to fix or establish key specifications for
your application. Please consult with your Omron’s representative at any time
to confirm actual specifications of purchased Product.
5. Errors and Omissions. Information presented by Omron Companies has been
checked and is believed to be accurate; however, no responsibility is assumed
for clerical, typographical or proofreading errors or omissions.
OMRON CANADA, INC. • HEAD OFFICE
Toronto, ON, Canada • 416.286.6465 • 866.986.6766 • www.omron247.com
OMRON ELECTRONICS DE MEXICO • HEAD OFFICE
México DF • 52.
55.59.01.43.00
• 001.800.556.6766 • mela@omron.com
OMRON ELECTRONICS DE MEXICO • SALES OFFICE
Apodaca, N.L. • 52.81.11.56.99.20 • 001.800.556.6766 • mela@omron.com
OMRON ELETRÔNICA DO BRASIL LTDA • HEAD OFFICE
São Paulo, SP, Brasil • 55.11.2101.6300 • www.omron.com.br
OMRON ARGENTINA • SALES OFFICE
Cono Sur • 54.11.4783.5300
OMRON CHILE • SALES OFFICE
Santiago • 56.9.9917.3920
OTHER OMRON LATIN AMERICA SALES
54.11.4783.5300
OMRON INDUSTRIAL AUTOMATION • THE AMERICAS HEADQUARTERS
Schaumburg, IL USA • 847.843.7900 • 800.556.6766 • www.omron247.com
OMRON EUROpE B.V. •
Wegalaan 67-69, NL-2132 JD, Hoofddorp, The Netherlands.
•
Tel: +31 (0) 23 568 13 00
Fax: +31 (0) 23 568 13 88
•
www.industrial.omron.eu
Cat. No. CSM_E3JM_E3JK_DS_E_10_1 03/12 Note: Specifications are subject to change. © 2012 Omron Electronics LLC Printed in U.S.A.