LED..A62X62W Series Area Lights
LED Area Lights for use with PresencePLUS® Pro sensors
Printed in USA 02/07 P/N 121779 rev. B
Features
• Low-cost, compact area lights for PresencePLUS Pro sensor. See Banner’s Web site
(www.bannerengineering.com) for a complete lighting tutorial.
• Solid-state LED matrix; continuous or strobed operation is selectable via sensor
software.
• Direct connection to PresencePLUS Pro or to an external power supply using 3
discrete wires.
• Two bracket options available.
Light Source LED, see Models table above for wave lengths
Illumination High-intensity area light
Supply Voltage and Current Infrared: 24V dc @ 150 mA max. All other colors: 24V dc @ 200 mA max.
Connections PVC-jacketed 3-conductor 2 m (6.5') attached cable
Construction Low-carbon steel with black zinc plating, acrylic window
Useful Life 10,000 hours (LED ON time). When operated within specifications, output will decrease less than 30% after
10,000 hours and less than 50% (less than 40% for red and IR models) after 20,000 hours.
Operating Conditions Temperature: 0° to +50° C (+32° to 122° F) Relative humidity: 90% at 50°C (non-condensing) max.
Cleaning Instructions Regularly remove any dust, dirt, or fingerprints from the light source.
1. Blow off dust using anti-static compressed air.
2. If necessary, use a lens cloth and lens cleaner or window cleaner to wipe off remaining debris. Do not use
any other chemicals for cleaning.
Specifications
Models Color Ambient Light
Filter Kit
Polarizing
Filter Kit
LEDIA62X62W Infrared, 940 nm FLTI (included with IR lights) —
LEDRA62X62W Visible Red, 630 nm FLTR (included with LEDAPFKS)
LEDAPFKS
LEDWA62X62W White, All Visible FLTB or FLTG
LEDBA62X62W Blue, 464 to 475 nm FLTB
LEDGA62X62W Green, 520 to 540 nm FLTG
Models
Wiring Table
Area Light
Wire
PresencePLUS Pro
Controller Terminal Block
External Power Supply
(Strobed)
External Power Supply
(Continuous)
Brown Pin 1 (+V*) +V +V
Blue Pin 2 (-V*) -V -V
White Pin 4 (strobe) +5V dc OFF
-V ON -V
White, Green, or
Blue LED models
Red or Infrared
LED models
Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN 55441 • Phone: 763.544.3164 • www.bannerengineering.com • sensors@bannerengineering.com
LED..A62X62W Series Area Lights
P/N 121779 rev. B
WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year.
Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture found
to be defective at the time it is returned to the factory during the warranty period. This warranty does
not cover damage or liability for the improper application of Banner products. This warranty is in lieu
of any other warranty either expressed or implied.
62 x 62 Models
14.7 mm
(0.58")
66.7 mm
(2.63")
66.7 mm
(2.63")
55.9 mm
(2.2")
55.9 mm
(2.2")
32 mm
(1.26")
64.2 mm
(2.53")
4.2 mm
(0.17") 1/4- 20 PEM Nut
Figure 1. Area light dimensions
NOTE: Before installing this area light it is recommended that an
ambient light filter be installed behind the lens. The filter
improves image quality by reducing unwanted ambient
light.
Sensing Shiny Surfaces
To eliminate direct reflections without using polarizing filters, angle
the sensor approximately 15° (or more) from perpendicular to a
shiny surface.
Polarizing Kit
If it is necessary to mount the camera at a 90° angle to a shiny
surface, the polarizing filter kit provides filters for both the LED area
light and sensor to reduce the negative effects of strong, direct light
reflections. The red filter kit (FLTR) is included with the polarizing
kit. When light colors other than red are used, discard the red filter
in the polarizing kit and use the proper filter listed on page 1. The
polarizing filters reduce the amount of light returned to the sensor.
Mounting Brackets
SMBVLA62X62S • Inline bracket
• 14 gauge steel, black zinc-plated SMBVLA62X62RA • Right-angle bracket
• 14 gauge steel, black zinc-plated
59.2 mm
(2.33")
53.3 mm
(2.10")
67.3 mm
(2.65")
63.5 mm
(2.50")
6.4 mm
(0.25")
8.4 mm
(0.33")
7.6 mm
(0.30")
38.1 mm
(1.50")
25.4 mm
(1.0")
1.9 mm
(0.07")
Clearance for M6 (1/4 - 20) hardware
(Hardware not included)
Clearance for
1/4 - 20 screw (Included)
59.2 mm
(2.33")
53.3 mm
(2.10")
67.3 mm
(2.65")
63.5 mm
(2.50")
8.4 mm
(0.33")
19.1 mm
(0.75")
21.2 mm
(0.84")
38.1 mm
(1.50")
38.1 mm
(1.50")
25.4 mm
(1.0")
25.4 mm
(1.0")
1.9 mm
(0.07")
Clearance for M6 (1/4 - 20) hardware
(Hardware not included)
Clearance for 1/4 - 20 screw (Included)
Installing the Area Light
