ESTABLISHED RELIABILITY CENTIGRID(R) ESTABLISHED RELIABILITY RELAY SERIES 116C DPDT CMOS COMPATIBLE SERIES DESIGNATION RELAY TYPE DPDT general-purpose relay with internal power MOSFET driver, Zener diode gate protection, and diode coil suppression 116C INTERNAL CONSTRUCTION DESCRIPTION UNI-FRAME UPPER STATIONARY CONTACT ARMATURE The 116C Centigrid(R) relay is an ultraminiature, hermetically sealed, armature relay capable of being directly driven by most IC logic families. Its low profile height and .100" grid spaced terminals, which preclude the need for spreader pads, make it ideal for applications where extreme packaging density and/or close PC board spacing are required. The basic concept and internal mechanical structure are similar to the 114 DPDT relay. The following unique construction features and manufacturing techniques provide overall high reliability and excellent resistance to environmental extremes: LOWER STATIONARY CONTACT * All welded construction. * Unique uni-frame design providing high magnetic efficiency and mechanical rigidity. * High force/mass ratios for resistance to shock and vibration. * Advanced cleaning techniques provide maximum assurance of internal cleanliness. * Precious metal alloy contact material with gold plating assures excellent high current and dry circuit switching capabilities. MOVING CONTACT ENVIRONMENTAL AND PHYSICAL SPECIFICATIONS Temperature (Ambient) -65C to +125C Vibration (General Note 1) 30 g's to 3000 Hz Shock (General Note 1) 75 g's, 6 msec, half-sine Acceleration 50 g's Enclosure Hermetically sealed Weight 0.11 oz. (3.12g) max. (c)2003 TELEDYNE RELAYS By virtue of its inherently low intercontact capacitance and contact circuit losses, the 116C relay has proven to be an excellent ultraminiature RF switch for frequency ranges well into the UHF spectrum. A typical RF application for this Centigrid(R) relay is in handheld radio transceivers, wherein the combined features of good RF performance, small size, low coil power dissipation and high reliability make it a preferred method of Transmit-Receive switching (see Figure 1). The Series 116C utilizes an internal silicon diode for coil suppression, a Zener diode to protect the MOSFET gate input, and an N-channel enhancement mode MOSFET chip, which enables direct relay interfacing with most Microprocessor and IC logic families (CMOS, TTL and MOS). SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE www.teledynerelays.com 116C Page 1 116C/1203/Q1 SERIES 116C GENERAL ELECTRICAL SPECIFICATIONS (-65C to +125C unless otherwise noted) (Notes 2 & 3) Contact Arrangement Rated Duty Contact Resistance 2 Form C (DPDT) Continuous 0.1 ohm max. before life; 0.2 ohm max. after life at 1A/28Vdc (measured 1/8" from header) Contact Load Ratings (DC) (See Fig. 2 for other DC resistive voltage/current ratings) Resistive: Inductive: Lamp: Low Level: 1 Amp/28Vdc 200 mA/28Vdc (320 mH) 100 mA/28Vdc 10 to 50 A/10 to 50mV Resistive: 250 mA/115Vac, 60 and 400 Hz (Case not grounded) 100 mA/115Vac, 60 and 400 Hz (Case grounded) Contact Load Ratings (AC) Contact Overload Rating 2A/28Vdc Resistive (100 cycles min.) Contact Carry Rating Contact factory Operate Time 2.5 msec max. at nominal rated coil voltage Release Time 4.0 msec max. Contact Bounce 1.5 msec max. Intercontact Capacitance 0.4 pf typical Insulation Resistance 10,000 megohms min. between mutually isolated terminals Dielectric Strength Atmospheric pressure: 500 Vrms/60Hz Negative Coil Transient (Vdc) Diode P.I.V. (Vdc) Zener Voltage (Vdc) Zener Leakage Current (AA @ 15.2 Vdc) Gate Voltage to Turn Off (Vdc, Max.) Power FET Characteristics Gate Voltage to Turn On (Vdc, Max.) -65C to +125C Drain-Source Voltage (Vdc, Max.) ESTABLISHED RELIABILITY 10,000,000 cycles (typical) at low level 1,000,000 cycles (typical) at 0.5A/28Vdc resistive 100,000 cycles min. at all other loads specified above Contact Life Ratings 70,000 ft.: 125 Vrms/60Hz 1.0 max 100 min. 17 min. to 23 max. 2.5 max 0.5 3.8 (Note 4) 55 DETAILED ELECTRICAL SPECIFICATIONS (-65C to +125C unless otherwise noted) (Note 3) BASE PART NUMBERS (See Note 8 for full P/N example) Nom. Max. Max. Coil Current (mAdc @25C) Min. Nominal Coil Operating Power @ 25C (Milliwatts) Pick-up Voltage (Vdc) (Note 4) Max. Min. Drop-out Voltage (Vdc) (Note 4) Max. Coil Voltage (Vdc) 116C-5 116C-6 116C-9 116C-12 116C-18 116C-26 5.0 5.6 132.3 96.5 641 4.0 0.13 2.3 6.0 8.0 83.9 60.3 462 4.9 0.18 3.2 9.0 12.0 47.1 33.1 368 7.3 0.27 4.9 12.0 16.0 36.1 24.9 369 9.8 0.36 6.5 18.0 24.0 24.1 16.1 368 14.6 0.54 9.8 26.5 32.0 19.9 12.9 450 19.5 0.72 13.0 PERFORMANCE CURVES (NOTE 2) TYPICAL RF PERFORMANCE 0 TYPICAL DC CONTACT RATING (RESISTIVE) INSERT ION LO .1 SS 300 .3 10 1.92 20 RETURN 30 40 50 60 1.07 S ACT ONT SC ROS N AC ATIO ISOL 1.22 SWR) LOSS (V LES S PO N ATIO OS ACR 1.02 1.01 1.00 ISOL 70 VSWR dB .4 LOAD VOLTAGE (VDC) .2 250 200 150 100 50 1.00 .01 116C Page 2 0.5 .1 .5 1.0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 FREQUENCY (GHz) LOAD CURRENT (AMPS DC) FIGURE 1 FIGURE 2 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE www.teledynerelays.com 0.8 0.9 1.0 (c)2003 TELEDYNE RELAYS 116C/1203/Q1 SERIES 116C SCHEMATIC DIAGRAM OUTLINE DIMENSIONS TERMINAL LOCATIONS (Viewed from Terminals; Numbers for Reference Only) CASE DETAIL .335 MAX. (8.51) .435 MAX. (11.05) .375 MAX. (9.53) .031 .003 (.79 .08) .275 MAX. (6.99) 9 8 ESTABLISHED RELIABILITY .75 MIN. (19.05) 7 .100 .010 (2.54 .25) 6 TYP +.002 (.051) .017 (.43) DIA. .001 (.043) 9 LEADS DIMENSIONS ARE SHOWN IN INCHES (MILLIMETERS) .035 .010 (.89 .25) PIN 1: + SUPPLY PIN 9: - SUPPLY PIN 10: GATE 10 1 2 3 .475 MAX. (12.06) 4 SCHEMATIC IS VIEWED FROM TERMINALS .200 .010 (5.08 0.25) TYPICAL CMOS INTERFACE CIRCUIT DC Logic Voltage Supply Vcc Vr Pin 1 GENERAL NOTES 1. Relay contacts will exhibit no chatter in excess of 10 sec or transfer in excess of 1 sec. 2. "Typical" characteristics are based on available data and are best estimates. No on-going verification tests are performed. 3. Unless otherwise specified, parameters are initial values. 4. Maximum rated gate voltage = 15 Vdc. 5. Unless otherwise specified, relays will be supplied with either gold plated or solder coated leads. 6. The slash and character appearing after the slash are not marked on the relay. 7. Screened HI-REL versions available. Contact factory. 8. Notes: Logic 1 activates the relay. Logic 0 de-activates the relay. Vcc = logic bias power. Vr = coil energization voltage. Logic element Pin10 1 = 3.8 to 15Vdc 0 = 0.5Vdc min. Pin 9 Teledyne Part Numbering System for T2R(R) Established Reliability Relay ER 116C Z M9 - 26 A / S Q Established Reliability Designator Q= Solder Coated Leads G= Gold Plated Leads (Notes 5 and 6) Relay Series Ground Pin Option (See Appendix) S= 0.187" leads (Note 6) Pad Option (See Appendix) Screening and Reliability Level Coil Voltage Teledyne Part Numbering System for Military Qualified (JAN) Relays J 116C Z M9 - 26 L Military (JAN) Designator Screening and Reliability Level Relay Series Ground Pin Option (See Appendix) Coil Voltage Pad Option (See Appendix) (c)2003 TELEDYNE RELAYS SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE www.teledynerelays.com 116C Page 3 116C/1203/Q1 Appendix A: Spacer Pads Pad designation and bottom view dimensions Height O.150 [3.81] (REF) Dim H MAX "M4" Pad for TO-5 Dim H MAX "M4" Pad for TO-5 Dim H MAX "M4" Pad for Centigrid(R) .156 [3.96] (REF) Dim H MAX .256 [6.5] (REF) "M9" Pad for Centigrid(R) For use with the following: ER411T ER412, ER412D, ER412DD 712, 712D, 712TN, RF300, RF310, RF320 ER420, ER422D, ER420DD, 421, ER421D, ER421DD, ER422, ER422D, ER422DD, 722, 722D, RF341 ER431T, ER432T, ER432, ER432D, ER432DD 732, 732D, 732TN, RF303, RF313, RF323 .295 (7.49) .300 (7.62) .305 (7.75) .400 (10.16) .410 (10.41) RF312 .350 (8.89) ER411, ER411D, ER411DD .295 (7.49) ER431, ER431D, ER431DD .400 (10.16) RF311 .300 (7.62) RF331 .410 (10.41) 172, 172D .305 (7.75) ER114, ER114D, ER114DD, J114, J114D, J114DD .300 (7.62) ER134, ER134D, ER134DD, J134, J134D, J134DD .400 (10.16) RF100 .315 (8.00) RF103 .420 (10.67) 122C, A152 .320 (8.13) ER116C, J116C .300 (7.62) ER136C, J136C .400 (10.16) RF180 .325 (8.25) A150 .305 (7.75) Notes: 1. Spacer pad material: Polyester lm. 2. To specify an "M4" or "M9" spacer pad, refer to the mounting variants portion of the part numbering example in the applicable datasheet. 3. Dimensions are in inches (mm). 4. Unless otherwise specied, tolerance is .010 (.25). 5. Add 10 m to the contact resistance show in the datasheet. 6. Add 0.01 oz. (0.25 g) to the weight of the relay assembly shown in the datasheet. (c) 2008 Teledyne Relays Dim. H Max. SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Appendix A: Spreader Pads Pad designation and bottom view dimensions Height For use with the following: .370 [9.4] MAX SQ .100 [2.54] Dim H MAX .150 [3.81] .014 [0.36] (REF) .300 [7.62] .100 [2.54] .370 [9.4] MIN .200 [5.08] "M" Pad 5/ 6/ .390 [9.91] SQ .100 [2.54] .100 [2.54] .150 [3.81] .300 [7.62] .300 [7.62] .150 [3.81] Dim H MAX ER411T, J411T, ER412, ER412D ER412DD, J412, J412D, J412DD ER412T, J412T 712, 712D, 712TN ER431T, J431T, ER432, ER432D ER432DD, J432, J432D, J432DD ER432T, J432T 732, 732D, 732TN .370 [9.4] MAX SQ .100 [2.54] Dim H MAX .150 [3.81] .014 [0.36] (REF) .300 [7.62] .100 [2.54] .200 [5.08] .370 [9.4] MIN "M3" Pad 5/ 6/ 9/ .393 (9.99) .493 (12.52) .503 (12.78) .398 (10.11) ER411T ER412, ER412D, ER412DD J412, J412D, J412DD .441 (11.20) 732, 732D "M2" Pad 7/ 8/ .388 (9.86) ER420, J420, ER420D, J420D ER420DD, J420DD, ER421, J421 ER421D, J421D, ER421DD J422D, ER422DD, J422DD, 722 712, 712D ER421, ER421D, ER421DD 722, 732D ER431T ER432, ER432D, ER432DD .130 [3.3] Dim. H Max. ER411, ER411D, ER411DD ER411TX ER412X, ER412DX, ER412DDX ER412TX 712X, 712DX, 712TNX ER420X, ER420DX, ER420DDX ER421X, ER421DX, ER421DDX ER422X, ER422DX ER422DDX, 722X, 722DDX ER431, ER431D, ER431DD ER431TX ER432X, ER432DX, ER432DDX ER432TX 732X, 732DX, 732TNX .451 (11.46) .451 (11.46) .546 (13.87) .556 (14.12) .388 (9.86) .393 (9.99) .398 (10.11) .493 (12.52) .503 (12.78) Notes: 1. Spreader pad material: Diallyl Phthalate. 2. To specify an "M", "M2" or "M3" spreader pad, refer to the mounting variants portion of the part number example in the applicable datasheet. 3. Dimensions are in inches (mm). 4. Unless otherwise specied, tolerance is .010" (0.25). 5/. Add 25 m to the contact resistance shown in the datasheet. 6/. Add .01 oz. (0.25 g) to the weight of the relay assembly shown in the datasheet. 7/. Add 50 m to the contact resistance shown in the datasheet. 8/. Add 0.025 oz (0.71 g) to the weight of the relay assembly shown in the datasheet. 9/. M3 pad to be used only when the relay has a center pin (e.g. ER411M3-12A, 722XM3-26.) (800) 284-7007 * www.teledynerelays.com +44 (0) 1236 453124 * www.teledyne-europe.com (c) 2008 Teledyne Relays Appendix A: Ground Pin Positions O.200 [O5.08] 363 "Z" POSITION "X" POSITION "Y" POSITION "Z" O.200 [O5.08] "Y" 453 TO-5 Relays: ER411T, ER412, ER412T, ER420, ER421, ER422, ER431T, ER432, ER432T, 712, 712TN, 400H, 400K, 400V, RF300, RF303, RF341, RF312, RF310, RF313, RF320, RF323 "Y" POSITION POSITION TO-5 Relays: ER411, ER431, RF311, RF331 POSITION .100 [2.54] "W" "Z" .100 [2.54] .050 [1.27] "X" .100 [2.54] POSITION POSITION "Z" POSITION POSITION .100 [2.54] POSITION "U" POSITION (ER116C and ER136C only) Centigrid(R) Relays: RF180, ER116C, 122C, ER136C .100 [2.54] Centigrid(R) Relays: RF100, RF103, ER114, ER134, 172 Indicates ground pin position Indicates glass insulated lead position Indicates ground pin or lead position depending on relay type (c) 2008 Teledyne Relays "Y" .100 [2.54] NOTES 1. Terminal views shown 2. Dimensions are in inches (mm) 3. Tolerances: .010 (.25) unless otherwise specied 4. Ground pin positions are within .015 (0.38) dia. of true position 5. Ground pin head dia., 0.035 (0.89) ref: height 0.010 (0.25) ref. 6. Lead dia. 0.017 (0.43) nom. SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE