XP1001000-03 - Lantronix - Product.Network

Key Features

• The only complete, integrat ed solution in an RJ45

form factor

• Complete integrated solution

• Embedded web server

• 10/100Mbit Ethernet – Auto-Sensing

• Stable, field proven TCP/IP protocol suite and web-

based application framework

• Easy configuration through a web interface

• Easy customization of HTML web pages and

configuration screens

• Interactive web pages through the use of Java

applets

• E-mail

• 128-, 192-, or 256-bit AES Rijndael e ncryption

(Optional)

• EMI tested and compliant

• Extended operating temperature:

-40 to +85˚ C normal mode

-40 to +75˚ C high-performance mode

• High-performance processor

(12 MIPS at 48 MHz, 22 MIPS at 88 MHz)

• Network overhead han dled by XPort

• Password protection

• Upgrade XPort’s firmware over the network

• 3.3V power

• Serial-to-10/100 Ethernet conversion

• 921,600 baud serial spee d

XPort™ Data Sheet

General Description

The XPort™ is the most compact, integrated

solution available to web-enable any device with a

serial interface. By simply adding XPort™ to a

product design, device manufacturers cut their

design cycle by as much as 80% and are able to

offer Ethernet connectivity in record time.

The XPort offers the highest level of integration

available in a device server. Within a compact

RJ45 package is a DSTni-EX 186 controller,

memory, 10/100 Ethernet transceiver, high-speed

serial port, status/diagnostic LEDs, and 3

programmable I/O pins. In the space that is

normally consumed by a connector, the XPort

provides a complete networking interface.

To enable access to a local network or the Internet,

the XPort integrates a fully developed TCP/IP

network stack and OS. The XPort also includes an

embedded web server used to remotely configure,

monitor, or troubleshoot the attached device.

Where there’s a need for custom user interfaces

and a desire to use common and familiar tools, the

XPort can serve web pages to a web browser. The

XPort becomes a conduit between you and your

device over the network or Internet.

The Windows™-based configuration software,

DeviceInstaller, simplifies installation and setup.

The XPort can also be set up locally through its

serial port, or remotely over a ne twork using Telnet

or a web browser. Flash memory provides for

maintenance-free nonvolatile storage of web

pages, and allows future system software

upgrades.

Using our highly integrated hardware and software

platform, you will add profit to your bottom line by

significantly reducing product development time,

risk, and cost.

XPort Data Sheet 910-815D Page 2 of 5

Hardware & Software Description

The XPort is a complete solution (hardware and

software) for web-enabling your edge devices.

Packed into an RJ45 connector smaller than your

thumb, this powerful device server comes with a

10BASE-T/100BASE-TX Ethernet connection, a

reliable and proven operating system stored in

flash memory, an embedde d web server, a full

TCP/IP protocol stack, and standard s-based (AES)

encryption.

The XPort software runs on a DSTni-EX controller

which has 256 KB of SRAM, 16 KB of boot ROM,

and a MAC with integrated 10/100BASE-TX PHY.

The XPort communicates to the edge device

through a 3.3V serial interface and three general-

purpose programmable I/O pins. 512 KB of flash

memory is included for storing firmware and web

pages. The XPort runs on 3.3V, and has a built-in

voltage supervisory circuit that will trigger a reset if

the supply voltage drops to unreliable levels (2.7V).

A built-in 1.8V regulator drives the processing core

of the EX controller.

An RJ45 Ethernet cable connects dire ctly into an

XPort. Ethernet magnetics, status LEDs, and

shielding are built in. The XPort was de signed to

meet class B emissions levels, which makes the

electromechanical integration very simple.

PCB Interface

The 8-pin PCB interface consists of 3.3V CMOS

Serial In/Out, 3 Flow Control/Handshake/PIO pins,

reset input, +3.3V power, and signal ground. All

pins are 5V tolerant.

Table 1 - PCB Interface Signals

Signal

Name Pin Function

GND 1 Circuit Ground

Vcc 2 +3.3V Power In

Reset (In) 3 External Reset In

Data OUT 4 Serial Data Out

Data IN 5 Serial Data In

CP1 6

CP1 can be configured as follows:

• Flow control: RTS (Request to Send)

output driven by DSTni’s built-in UART

for connection to CTS of attached

device.

• Programmable input/output: CP1 can

be driven or read through software

control, independent of serial port

activity.

CP2 7

CP2 can be configured as follows:

• Modem control: DTR (Data Terminal

Ready) output driven by DSTni’s built-

in UART for connection to DCD of

attached device.

• Programmable input/output: CP2 can

be driven or read through software

control, independent of serial port

activity.

CP3 8

CP3 can be configured as follows:

• Flow control: CTS (Clear to Send)

input read by DSTni’s built-in UART for

connection to RTS of attached device.

• Modem control: DCD (Data Carrier

Detect) input read by DSTni’s built-in

UART for connection to DTR of

attached device.

• Programmable input/output: CP3 can

be driven or read through software

control, independent of serial port

activity.

Ethernet Interface

The 10/100 Ethernet magnetics, network status

LEDs, and RJ45 connector are integrated into the

XPort.

Table 2 - Ethernet Interface Signals

Signal Name DIR Contact Primary Function

TX+ Out 1 Transmit Data +

TX- Out 2 Transmit Data –

RX+ In 3 Receive Data +

RX- In 6 Receive Data –

Not Used 4 Terminated

Not Used 5 Terminated

Not Used 7 Terminated

Not Used 8 Terminated

SHIELD Chassis Ground

LEDs

RJ45

CMOS IO RESET +3.3VDC

DSTni-EX

FLASH 25MHz

MAGNETICS Rx

XPort Data Sheet 910-815D 10/2004 Page 3 of 5

Protocol Support

The XPort uses Internet Protocol (IP) for network

communications a nd Transmission Control

Protocol (TCP) to assure that no data is lost or

duplicated, and that everything sent arrives

correctly at the target.

Other supported proto cols are listed below:

• ARP, UDP, TCP, ICMP, Telnet, TFTP, AutoIP,

DHCP, HTTP, and SNMP for network

communications.

• TCP, UDP, and Telnet for connections to the serial

port.

• TFTP for firmware updates.

• IP for addressing, routing, and data block handling

over the network.

• User Datagram Protocol (UDP) for typical datagram

applications in which devices interact with other

devices without maintaining a point-to-point

connection.

* For a complete discussion of protocol support,

see the XPort user manual.

LEDs

The device contains two bi-color LEDs built into the

front of the XPort connector. (See dimension

drawing for location.)

Link LED (Left Side) Activity LED (Right Side)

Color Meaning Color Meaning

Off No Link Off No Activity

Amber 10 Mbps Amber Half-Duplex

Green 100 Mbps Green Full-Duplex

Recommended PC Board Layout

The hole pattern and mounting dimensions for the

XPort are shown in the following drawing:

Dimensions

The XPort dimensions are shown in the following

drawings:

RIGHT

LED

18.25 [0.719]

16.25 [0.640]

11.55 [0.455]

7.15 [0.281]

CON TA C T 1

CON TA CT 8

5.85 [0.230]

14.50 [0.571] 4.03 [0.158]

13.50 [0.531]

1.85 [0.073]

3.25 [0.128]

3.30 [0.130]

1.27 [0.050]

0.40 [0.016]

FRONT

VIEW

DIMS = mm (in)

LEFT

LED

SHIELD TAB

TOLERANCE

.XX+/-0.20[0.008]

7 1

BOTTOM

VIEW

33.90 [1.335 ]

1.00 [0.039]

0.35 [0.014] 10.8 4 [0.427]

6.35 [0.250]

2.54 [0.100] 3.20 [0.126]

0.60 [0.024]

FRONT SHIELD

GROUND

INTERFACE

PINS

DIMS = mm ( in)

11.90 [0.468]

SHIELD TAB

TOLERANCE

.XX+/-0.20[0.008]

Note: PADS and PROTEL design files are incl uded

with the XPort development kit.

16.05

[0.632]

12.30

[0.484]

10.84 [0.427]

6.35 [0.250]

2.54 [0.100]

3.25 [ 0.128]

O O

0.90 [ 0.035]

O 1.60[ 0.063]

7 1.27 [0.050]

2.54 [0.100]

FRONT

11.90 [0.468]

DIMS = mm ( i n)

SHIELD TAB

TOLERANCE

.XX+/-0.05[0.002]

3.58 [0.141]

For proper heat dissipation, the PCB should

have approximately 1 square inch of copper

attached to the shield tabs. The shiel d tabs are

an important source of heat sinking for the

device.

XPort Data Sheet 910-815D 10/2004 Page 4 of 5

XPort Technical Data

Category Description

CPU, Memory Lantronix DSTni-E X 186 CPU, 256 KB zero wait state SRAM

512 KB Flash, 16 KB Boot ROM

Firmware Upgradeable via T FTP and serial port

Reset Circuit Internal 200ms power-up reset pulse. Power-drop reset triggered at 2.6V. External res et

input causes an internal 200ms reset.

Serial Interface CMOS (Asynchronous) 3.3V-level signals

Rate is software selectable (300 bps to 921600 bps)

Serial Line Formats 7 or 8 data bits, 1-2 Stop bits, Parity: odd, even, none

Modem Control DTR/DCD, CTS, RTS

Flow Control XON/XOFF (software), CTS/RTS (hardware), none

Programmable I/O 3 PIO pins (software selectable) sink or source 4mA max.

Network Interface RJ45 Ethernet 10BASE-T or 100BASE-TX (auto-sensing)

Compatibility Ethernet: Version 2.0/IEEE 802.3

Protocols Supported ARP, UDP/IP, TCP/IP, Telnet, ICMP, SNMP, DHCP, BOOTP, TFTP, Auto IP, and HTTP

LEDs 10BASE-T & 100BASE-TX Link Activity, Full/half duplex. Sofware generated status &

diagnostic signals can optionally drive external LEDs through CP1 & CP3 (see Int. Guide).

Management Internal web server, SNMP, Serial login, Telnet logi n

Security Password protection, locking features, optional Rijndael 128-, 192-, or 25 6-bit encryption

Internal Web Server Serves web pages

Storage capacit y: 384 KB

Weight 9.6 grams (0.34 oz)

Material Metal shell, thermoplastic case

Temperature Operating range: -40°C to +85°C (-40°F to 185°F ) normal mode

-40°C to +75°C (-40°F to 167°F) high-performance mode

Storage range: -40°C to +85°C (-40°F to 185°F )

Relative Humidit y Operating: 5% to 95% non-condensing

Shock/Vibration Non-operational shock: 500 g's, Non-operationa l vibration: 20 g's

Warranty 2-year limited warranty

Included Software Windows™ 98/NT /2000/XP-based DeviceInstaller configuration software and Windows™-

based Comm Port Redirector

EMI Compliance Radiated & conducted emissions - complies with Class B limits of EN 55022:1998

Direct & Indirect ESD - complies with EN55024:1998

RF Electromagnetic Field Immunity - complies with EN55024:1998

Electrical Fast Transient/Burst Immunit y - complies with EN55024:1998

Power Frequency Magnetic Field Immunity - complies with EN55024:1998

RF Common Mode Conducted Susceptibility - complies with EN55024:1998

DC Characteristics for Serial, PIO, and Power Interface

Symbol Parameter Min Nominal Max Units

Vcc Supply voltage (typical 3.3) (+/-5%) 3.14 3.3 3.46 V

VIL Low Level Input Voltage 0 0.8 V

VIH High Level Input Voltage 2.0 5.5 V

VOL Low Level Output Voltage 0.4 V

VOH High Leve l Output Voltage 2.4 V

II Input Leakage Current 1 µA

ICC Supply Current (idle)@ 48 MHz 119 mA

ICC Supply Current (10BASE-T activity)@ 48 MHz 224 mA

ICC Supply Current (10BASE-T activity)@ 88 MHz 267 mA

ICC Supply Current (100BASE-T activity)@ 48 MHz 190 mA

lCC Supply Current (100BASE-T activit y)@ 88 MHz 233 mA

With the purchase of XPort, the OEM agrees to an OEM firm ware license agreement that grants the OEM a non-exclus ive,

royalty-free firmware license to use and dist ribute the binary firmware image provided, only to the extent necessary to use

the XPort hardware.

XPort Data Sheet 910-815D 10/2004 Page 5 of 5

Development Kit

Introduction

An XPort development kit is available to provide a

simple, quick, and cost-effective way to evaluate

the XPort. Use the development kit to integrate the

XPort to your product design, and give your newly

networked product a test drive.

Features of the Development Kit

• Complete, ready to use XPort and sup porting

evaluation board

• +5VDC Universal Power Supply

• RS-232 cable, DB9M/F

• CAT5e UTP RJ45M/M Ethernet cable

• Serial adapter, 25-pin to 9-pin

• XPort CD containing a configuration utility,

DeviceInstaller, Comm Port Redire ctor, sample

code and complete user manual in PDF

Block Diagram

TP8 TP9

XPort

DIP

SWITCH

RESET

VDC

3.3V

POWER

PIO

RS232

PLD

TMR

LEDs

SLOW

PWR

LED

RTS, DCD

DTR, CTS

PLD HEADER

RXD/TXD

SWITCH

RESET PADS

JP3

JP4

SW1SW2

DB-9F

TP13

TP11

RTS

DTR

CTS/DCD

Features of the Evaluation Board

The XPort evaluation board includes an XPort

integrated with the following features:

• RS-232 (DCE) se rial interface

• DIP switch configuration

• LED indication for power, RS-232 tran smit /

receive and PIO status

• Reset circuit with pushbutton

• Header connector for the PIO signals CP1,

CP2, and CP3

• Test points to monitor the XPort’s serial

interface signals

• Timer

Ordering Information

XPort-XE XP1001000-03 Standard XPort Min. order: 50 units

XPort-SE XP1002000-03

Standard XPort with

256-bit AES encryption Min. order: 50 units

XPort-SE SMPL XP100200S-03 XPort Sample with

encryption One XPort enclosed

Xport Dev. Kit XP100 200K-03 XPort Development Kit

with encryption

For details contact your local Lantronix representative or Lantronix directly:

Asia Pacific Region via e-mail at AsiaPacific_sales@lantronix.com

Europe via e-mail at eu_sales@lantronix.com

Japan via e-mail at japan_sales@lantronix.com

United States via e-mail at sales@lantronix.com or call OEM sales support at 800-526-8764