Am79C978 PCnetTM- Home Single-Chip 1/10 Mbps PCI Home Networking Controller DISTINCTIVE CHARACTERISTICS n Fully integrated 1 Mbps HomePNA Physical Layer (PHY) as defined by Home Phoneline Networking Alliance (HomePNA) specification 1.1 -- Supports both PCI 5.0-V and 3.3-V signaling environments -- Plug and Play compatible -- Supports an unlimited PCI burst length -- Optimized for home networking applications over ordinary telephone wire -- Big endian and little endian byte alignments supported -- In-band control features: -- Implements optional PCI power management event (PME) pin Adjustable power and speed levels n Dual-speed CSMA/CD (10 Mbps and 100 Mbps) Media Access Controller (MAC) compliant with IEEE/ANSI 802.3 Ethernet standard 32 bits of reserved in-band messaging piggybacked on Ethernet packet -- Register programmable features: n Media Independent Interface (MII) for connecting external 10/100 Mbps transceivers Power control Performance registers -- IEEE 802.3u compliant MII Speed control -- Intelligent Auto-PollTM external PHY status monitor and interrupt Major frame timing parameters programmable: ISBI, AID ISBI, pulse width, inter-symbol time -- Supports both auto-negotiable and nonauto-negotiable external PHYs -- Supports 10BASE-T, 100BASETX/FX, 100BASET4, and 100BASET2 IEEE 802.3 compliant MII PHYs at full-duplex or halfduplex n Fully integrated 10 Mbps PHY interface -- Comprehensive Auto-Negotiation implementation -- Full-duplex capability n Full-duplex operation supported on the MII port with independent Transmit (TX) and Receive (RX) channels -- Optimized for 10BASE-T applications n Integrated Fast Ethernet controller for the Peripheral Component Interconnect (PCI) bus n Supports PC98 and Net PC specifications -- 32-bit glueless PCI host interface -- Supports PCI clock frequency from DC to 33 MHz independent of network clock -- Implements full OnNow features including pattern matching and link status wake-up events -- Supports network operation with PCI clock from 15 MHz to 33 MHz -- Implements Magic PacketTM mode -- Magic Packet mode and the physical address loaded from EEPROM at power up without requiring PCI clock -- High performance bus mastering architecture with integrated Direct Memory Access (DMA) Buffer Management Unit for low CPU and bus utilization -- Supports PCI Bus Power Management Interface specification revision 1.1 -- PCI draft specification revision 2.2 compliant -- Supports Advanced Configuration and Power Interface (ACPI) specification version 1.0 -- Supports PCI Subsystem/Subvendor ID/ Vendor ID programming through the EEPROM interface -- Supports Network Device Class Power Management specification version 1.0a Publication# 22206 Rev: D Amendment/0 Issue Date: November 1999 R f t AMD' W b it ( d )f th l t t i f ti n Independent internal TX and RX FIFOs -- Programmable FIFO watermarks for both TX and RX operations by allowing protocol analysis to begin before the end of a receive frame -- RX frame queuing for high latency PCI bus host operation n Includes Programmable Inter Packet Gap (IPG) to address less network aggressive MAC controllers -- Programmable allocation of buffer space between RX and TX queues n Offers the Modified Back-Off algorithm to address the Ethernet Capture Effect n Extensive programmable internal/external loopback capabilities n EEPROM interface supports jumperless design and provides through-chip programming -- Supports full programmability of half-/fullduplex operation through EEPROM mapping -- Programmable PHY reset output pin capable of resetting external PHY without the need for buffering n Extensive programmable LED status support n Look-Ahead Packet Processing (LAPP) data handling technique reduces system overhead n IEEE 1149.1-compliant JTAG Boundary Scan test access port interface and NAND tree test mode for board-level production connectivity test n Software compatible with AMD's PCnetTM Family and LANCE/C-LANCE register and descriptor architecture n Very low power consumption n +3.3 V power supply along with 5 V tolerant I/Os enable broad system compatibility n Available in 144-pin TQFP and 160-pin PQFP packages GENERAL DESCRIPTION The Am79C978 controller is the first in a series of home networking products from AMD. The Am79C978 controller is fabricated in an advanced low power 3.3 V CMOS process to provide low operating current for power sensitive applications. The Am79C978 controller contains an Ethernet Controller based on the Am79C971 Fast Ethernet controller, a physical layer device for supporting the 802.3 standard for 10BASE-T, and a physical layer device for data networking at speeds up to 1 Mbps over ordinary residential telephone wiring. The integrated PCI Ethernet controller is a highly integrated 32-bit full-duplex, 10/100 Mbps Ethernet controller solution designed to address high-performance system application requirements. It is a flexible busmastering device that can be used in any application, including network ready PCs. The bus master architecture provides high data throughput and low CPU and system bus utilization. system. The device has built-in support for both little and big endian byte alignment. The integrated home networking controller's advanced CMOS design allows the bus interface to be connected to either a +5.0 V or a +3.3 V signaling environment. A compliant IEEE 1149.1 JTAG test interface for board level testing is also provided, as well as a NAND tree test structure for those systems that do not support the JTAG interface. The integrated Am79C978 home networking controller is also compliant with the PC98 and Net PC specifications. It includes the full implementation of the Microsoft OnNow and ACPI specifications, which are backward compatible with Magic Packet technology. It is also compliant with the PCI Bus Power Management Interface specification by supporting the four power management states (D0, D1, D2, and D3), the optional PME pin, and the necessary configuration and data registers. The integrated HomePNA transceiver is a physical layer device that enables data networking at speeds up to 1 Mbps over common residential phone wiring regardless of topology and without disrupting telephone (POTS) service. The integrated Am79C978 home networking controller is a complete Ethernet or home network node integrated into a single VLSI device. It contains a bus interface unit, a Direct Memory Access (DMA) Buffer Management Unit, an ISO/IEC 88023 (IEEE 802.3) compliant Media Access Controller (MAC), a Transmit FIFO and a large Receive FIFO, and an IEEE 802.3u compliant MII. Both IEEE 802.3 compliant full-duplex and half-duplex operations are supported on the MII interface. 10/100 Mbps operation is supported through the MII interface. The 32-bit multiplexed bus interface unit provides a direct interface to the PCI local bus, simplifying the design of an Ethernet or home network node in a PC The integrated Am79C978 home networking controller is register compatible with the LANCE (Am7990) and C-LANCE (Am79C90) Ethernet controllers and all The integrated Ethernet transceiver is a physical layer device supporting the IEEE 802.3 standards for 10BASE-T. It provides all of the PHY layer functions required to support 10 Mbps data transfer speeds. 2 Am79C978 Ethernet controllers in the PCnet Family (except ILACCTM (Am79C900)), including PCnet-ISA (Am79C960), PCnet-ISA+ (Am79C961), PCnet-ISA II (Am79C961A), PCnet-32 (Am79C965A), PCnet-PCI (Am79C970), PCnet-PCI II (Am79C970A), PCnetFAST (Am79C971), and PCnet-FAST+ (Am79C972). The Buffer Management Unit supports the LANCE and PCnet descriptor software models. While consuming minimal network resources, AMD's innovative any1HomeTM Link Detection Packet for HomePNA networks provides a means to indicate to the MAC and thus the upper layers of the system protocol that a valid network (as defined by Home Networking Alliance) has been detected. The Link Detection Packet is also capable of detecting a network failure and allows the upper layer protocol to take cor- rective action. Thus, the Link Detection Packet ensure strict compliance to the Microsoft PC97, PC98, and Home PNA requirements. The integrated Am79C978 controller supports autoconfiguration in the PCI configuration space. Additional integrated controller configuration parameters, including the unique IEEE physical address, can be read from an external non-volatile memory (EEPROM) immediately following system reset. In addition, the Am79C978 controller provides programmable on-chip LED drivers for transmit, receive, collision, link integrity, Magic Packet status, speed, activity, power output, address match, full-duplex, or 100 Mbps status. Am79C978 3 MDC MDIO RXD(3:0)/TXD(3:0) XTAL2 Clock Reference XTAL1 BLOCK DIAGRAM 1Mbps HomePNA PHY Transmit State Machine MII Interface CLK RST AD[31:0] C/BE[3:0] PAR FRAME TRDY IRDY STOP IDSEL DEVSEL REQ GNT PERR SERR INTA HRTXRXP/N Receive State Machine MII Management PHY Control Bus Rcv FIFO PCI Bus Interface Unit MAC Rcv FIFO Analog Front End Link Monitor 10 Mbps PHY 802.3 MAC Core MII Interface 12K SRAM Transmit State Machine TX 10 BASE-T Bus Xmt FIFO MAC Xmt FIFO FIFO Control Network Port Manager MDC MDIO MII Management RX Receive State Machine Link Monitor Buffer Management Unit Auto Negotiation PHY Control LED Control TCK TMS TDI TDO Drive Control OnNow Power Management Unit JTAG Port Control 93C46 EEPROM Interface LED0 LED1 LED2 LED3 LED4 EECS EESK EEDI EEDO PME PG 22206B-1 4 Am79C978 TABLE OF CONTENTS DISTINCTIVE CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 GENERAL DESCRIPTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 BLOCK DIAGRAM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 RELATED AMD PRODUCTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 CONNECTION DIAGRAM (144 TQFP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 CONNECTION DIAGRAM (160 PQFP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 PIN DESIGNATIONS (PQL144) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Listed By Pin Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 PIN DESIGNATIONS (PQR160) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Listed By Pin Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 PIN DESIGNATIONS (PQL144) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Listed By Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 PIN DESIGNATIONS (PQR160) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Listed By Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Listed By Driver Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 ORDERING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Standard Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 PIN DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 PCI Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Magic Packet Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Board Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 EEPROM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 MII Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 IEEE 1149.1 (1990) Test Access Port Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Ethernet Network Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 HomePNA PHY Network Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Clock Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 BASIC FUNCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 System Bus Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Software Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Network Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Media Independent Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 MII Transmit Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 MII Receive Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 MII Network Status Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 MII Management Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 MII Management Frames. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 Auto-Poll External PHY Status Polling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 Network Port Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 10BASE-T PHY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 PCI and JTAG Configuration Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Slave Bus Interface Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Slave Configuration Transfers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Slave I/O Transfers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Expansion ROM Transfers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Slave Cycle Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Disconnect When Busy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 Disconnect Of Burst Transfer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 Parity Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Master Bus Interface Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Bus Acquisition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Bus Master DMA Transfers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Basic Non-Burst Read Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Basic Burst Read Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Basic Non-Burst Write Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 Basic Burst Write Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 Target Initiated Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 Disconnect With Data Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 Am79C978 5 Disconnect Without Data Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 Target Abort . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 Master Initiated Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 Preemption During Non-Burst Transaction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 Preemption During Burst Transaction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 Master Abort . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 Parity Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 Advanced Parity Error Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 Initialization Block DMA Transfers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 Descriptor DMA Transfers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 FIFO DMA Transfers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 Non-Burst FIFO DMA Transfers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 Burst FIFO DMA Transfers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 Buffer Management Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 Re-Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 Suspend. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 Buffer Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 Descriptor Rings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 Polling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 Transmit Descriptor Table Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 Receive Descriptor Table Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64 Receive Frame Queuing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64 Software Interrupt Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 10/100 Media Access Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Transmit and Receive Message Data Encapsulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Framing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Destination Address Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 Error Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 Media Access Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Medium Allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Collision Handling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 Transmit Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 Transmit Function Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 Automatic Pad Generation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 Transmit FCS Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 Transmit Exception Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 Loss of Carrier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 Late Collision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 SQE Test Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 Receive Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 Receive Function Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 Address Matching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71 Automatic Pad Stripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72 Receive FCS Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72 Receive Exception Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72 Loopback Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 Miscellaneous Loopback Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 Full-Duplex Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 Full-Duplex Link Status LED Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74 PHY/MAC Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74 DETAILED FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 1 Mbps HomePNA PHY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 HomePNA PHY Medium Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 Framing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 HomePNA Symbol Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 Time Interval Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 ACCESS ID Intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 Symbol 0 (SYNC interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 SYNC Transmit Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 6 Am79C978 SYNC Receive Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 AID Symbols 1 through 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 AID Transmit Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 AID Receive Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Collisions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 JAM Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 ACCESS ID Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Silence Interval (AID symbol 7). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Data Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Data Transmit Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Data Receive Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Data Symbol RLL25 Encoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Management Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Header AID Remote Control Word Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 PHY Control and Management Block (PCM Block) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Register Administration for 10BASE-T PHY Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Description of the Methodology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 SRAM Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Low Latency Receive Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Direct SRAM Access. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 EEPROM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Automatic EEPROM Read Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 EEPROM Auto-Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Direct Access to the Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 EEPROM-Programmable Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 EEPROM MAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 LED Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Power Savings Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 Power Management Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 OnNow Wake-Up Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 Link Change Detect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 OnNow Pattern Match Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Pattern Match RAM (PMR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Magic Packet Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 IEEE 1149.1 (1990) Test Access Port Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Boundary Scan Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 TAP Finite State Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Supported Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Instruction Register and Decoding Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Boundary Scan Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Other Data Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 NAND Tree Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 H_RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 S_RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 STOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 Power on Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 Software Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 PCI Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 I/O Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 I/O Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 Address PROM Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 Reset Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 Word I/O Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 Double Word I/O Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 10BASE-T Physical Layer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 Twisted Pair Transmit Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 Twisted Pair Receive Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 Twisted Pair Interface Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 Collision Detect Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 Am79C978 7 Jabber Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 Reverse Polarity Detect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 Auto-Negotiation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 Soft Reset Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100 USER ACCESSIBLE REGISTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101 PCI Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 PCI Vendor ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 PCI Device ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 PCI Command Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 PCI Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104 PCI Revision ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105 PCI Programming Interface Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105 PCI Sub-Class Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105 PCI Base-Class Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106 PCI Latency Timer Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106 PCI Header Type Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106 PCI I/O Base Address Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106 PCI Memory Mapped I/O Base Address Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 PCI Subsystem Vendor ID Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 PCI Subsystem ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 PCI Expansion ROM Base Address Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108 PCI Capabilities Pointer Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108 PCI Interrupt Line Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108 PCI Interrupt Pin Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 PCI MIN_GNT Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 PCI MAX_LAT Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 PCI Capability Identifier Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 PCI Next Item Pointer Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 PCI Power Management Capabilities Register (PMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 PCI Power Management Control/Status Register (PMCSR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 PCI PMCSR Bridge Support Extensions Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 PCI Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 RAP Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 RAP: Register Address Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 Control and Status Registers (CSRs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 CSR0: Controller Status and Control Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 CSR1: Initialization Block Address 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115 CSR2: Initialization Block Address 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115 CSR3: Interrupt Masks and Deferral Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115 CSR4: Test and Features Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118 CSR5: Extended Control and Interrupt 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119 CSR6: RX/TX Descriptor Table Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122 CSR7: Extended Control and Interrupt 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122 CSR8: Logical Address Filter 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125 CSR9: Logical Address Filter 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125 CSR10: Logical Address Filter 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125 CSR11: Logical Address Filter 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126 CSR12: Physical Address Register 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126 CSR13: Physical Address Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126 CSR14: Physical Address Register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126 CSR15: Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127 CSR16: Initialization Block Address Lower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128 CSR17: Initialization Block Address Upper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128 CSR18: Current Receive Buffer Address Lower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128 CSR19: Current Receive Buffer Address Upper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128 CSR20: Current Transmit Buffer Address Lower. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129 CSR21: Current Transmit Buffer Address Upper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129 CSR22: Next Receive Buffer Address Lower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129 CSR23: Next Receive Buffer Address Upper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129 CSR24: Base Address of Receive Ring Lower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129 8 Am79C978 CSR25: Base Address of Receive Ring Upper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129 CSR26: Next Receive Descriptor Address Lower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129 CSR27: Next Receive Descriptor Address Upper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .130 CSR28: Current Receive Descriptor Address Lower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .130 CSR29: Current Receive Descriptor Address Upper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .130 CSR30: Base Address of Transmit Ring Lower. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .130 CSR31: Base Address of Transmit Ring Upper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .130 CSR32: Next Transmit Descriptor Address Lower. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .130 CSR33: Next Transmit Descriptor Address Upper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .130 CSR34: Current Transmit Descriptor Address Lower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131 CSR35: Current Transmit Descriptor Address Upper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131 CSR36: Next Next Receive Descriptor Address Lower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131 CSR37: Next Next Receive Descriptor Address Upper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131 CSR38: Next Next Transmit Descriptor Address Lower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131 CSR39: Next Next Transmit Descriptor Address Upper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131 CSR40: Current Receive Byte Count. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131 CSR41: Current Receive Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132 CSR42: Current Transmit Byte Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132 CSR43: Current Transmit Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132 CSR44: Next Receive Byte Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132 CSR45: Next Receive Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132 CSR46: Transmit Poll Time Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132 CSR47: Transmit Polling Interval. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .133 CSR48: Receive Poll Time Counter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .133 CSR49: Receive Polling Interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .133 CSR58: Software Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134 CSR60: Previous Transmit Descriptor Address Lower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136 CSR61: Previous Transmit Descriptor Address Upper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136 CSR62: Previous Transmit Byte Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136 CSR63: Previous Transmit Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136 CSR64: Next Transmit Buffer Address Lower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136 CSR65: Next Transmit Buffer Address Upper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136 CSR66: Next Transmit Byte Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136 CSR67: Next Transmit Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137 CSR72: Receive Ring Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137 CSR74: Transmit Ring Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137 CSR76: Receive Ring Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137 CSR78: Transmit Ring Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137 CSR80: DMA Transfer Counter and FIFO Threshold Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . .138 CSR82: Transmit Descriptor Address Pointer Lower. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140 CSR84: DMA Address Register Lower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140 CSR85: DMA Address Register Upper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140 CSR86: Buffer Byte Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140 CSR88: Chip ID Register Lower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .141 CSR89: Chip ID Register Upper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .141 CSR92: Ring Length Conversion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .141 CSR100: Bus Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .141 CSR112: Missed Frame Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .142 CSR114: Receive Collision Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .142 CSR116: OnNow Power Mode Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .142 CSR122: Advanced Feature Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .143 CSR124: Test Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .143 CSR125: MAC Enhanced Configuration Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .144 Bus Configuration Registers (BCRs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .145 BCR0: Master Mode Read Active . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .145 BCR1: Master Mode Write Active . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .145 BCR2: Miscellaneous Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .145 BCR4: LED0 Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147 BCR5: LED1 Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .149 BCR6: LED2 Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .151 Am79C978 9 BCR7: LED3 Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .153 BCR9: Full-Duplex Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .155 BCR16: I/O Base Address Lower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .155 BCR17: I/O Base Address Upper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .155 BCR18: Burst and Bus Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156 BCR19: EEPROM Control and Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .158 BCR20: Software Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .161 BCR22: PCI Latency Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .163 BCR23: PCI Subsystem Vendor ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .163 BCR24: PCI Subsystem ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .164 BCR25: SRAM Size Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .164 BCR26: SRAM Boundary Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .164 BCR27: SRAM Interface Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .165 BCR28: Expansion Bus Port Address Lower (Used for Flash/EPROM and SRAM Accesses) . . . .166 BCR29: Expansion Port Address Upper (Used for Flash/EPROM Accesses). . . . . . . . . . . . . . . . .167 BCR30: Expansion Bus Data Port Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167 BCR31: Software Timer Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .168 BCR32: PHY Control and Status Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .168 BCR33: PHY Address Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .170 BCR34: PHY Management Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171 BCR35: PCI Vendor ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171 BCR36: PCI Power Management Capabilities (PMC) Alias Register . . . . . . . . . . . . . . . . . . . . . . .172 BCR37: PCI DATA Register 0 (DATA0) Alias Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .172 BCR38: PCI DATA Register 1 (DATA1) Alias Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .172 BCR39: PCI DATA Register 2 (DATA2) Alias Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .172 BCR40: PCI DATA Register 3 (DATA3) Alias Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .173 BCR41: PCI DATA Register 4 (DATA4) Alias Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .173 BCR42: PCI DATA Register 5 (DATA5) Alias Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .174 BCR43: PCI DATA Register 6 (DATA6) Alias Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .174 BCR44: PCI DATA Register 7 (DATA7) Alias Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .174 BCR45: OnNow Pattern Matching Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .175 BCR46: OnNow Pattern Matching Register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .175 BCR47: OnNow Pattern Matching Register 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .176 BCR48: LED4 Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .176 BCR49: PHY Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .178 BCR50-BCR55: Reserved Locations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .178 1 Mbps HomePNA PHY Internal Registers 179 HPR0: HomePNA PHY MII Control (Register 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .179 HPR1: HomePNA PHY MII Status (Register 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 HPR2 and HPR3: HomePNA PHY MII PHY ID (Registers 2 and 3) . . . . . . . . . . . . . . . . . . . . . . . .181 HPR4-HPR7: HomePNA PHY Auto-Negotiation (Registers 4 - 7). . . . . . . . . . . . . . . . . . . . . . . . . .181 Reserved Registers: HPR8 - HPR15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .181 HPR16: HomePNA PHY Control (Register 16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182 HPR17: HomePNA Status Control (Register 17). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 HPR18 and HPR19: HomePNA PHY TxCOMM (Registers 18 and 19) . . . . . . . . . . . . . . . . . . . . .183 HPR20 and HPR21: HomePNA PHY RxCOMM (Registers 20 and 21) . . . . . . . . . . . . . . . . . . . . 184 HPR22: HomePNA PHY AID (Register 22) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .184 HPR23: HomePNA PHY Noise Control (Register 23) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .184 HPR24: HomePNA PHY Noise Control 2 (Register 24) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .185 HPR25: HomePNA PHY Noise Statistics (Register 25). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .185 HPR26: HomePNA PHY Event Status (Register 26). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186 HPR27: HomePNA PHY Event Status (Register 27). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .186 HPR28: HomePNA PHY ISBI Control (Register 28) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .186 HPR29: HomePNA PHY TX Control (Register 29) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .187 HPR30: 1 Mbps HomePNA PHY Drive Level Control Test Register (Register 30) . . . . . . . . . . . . .187 HPR31: 1 Mbps HomePNA PHY Analog Control Register (Register 31) . . . . . . . . . . . . . . . . . . . .187 10BASE-T PHY Management Registers (TBRs) 188 TBR0: 10BASE-T PHY Control Register (Register 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .189 TBR1: 10BASE-T Status Register (Register 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190 TBR2 and TBR3: 10BASE-T PHY Identifier (Registers 2 and 3). . . . . . . . . . . . . . . . . . . . . . . . . . 191 10 Am79C978 TBR4: 10BASE-T Auto-Negotiation Advertisement Register (Register 4) . . . . . . . . . . . . . . . . . . .192 TBR5: 10BASE-T Auto-Negotiation Link Partner Ability Register (Register 5) . . . . . . . . . . . . . . . .193 TBR6: 10BASE-T Auto-Negotiation Expansion Register (Register 6) . . . . . . . . . . . . . . . . . . . . . . 194 TBR7: 10BASE-T Auto-Negotiation Next Page Register (Register 7) . . . . . . . . . . . . . . . . . . . . . . .194 Reserved Registers (Registers 8-15, 18, 20-23, and 25-31) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .194 TBR16: 10BASE-T INTERRUPT Status and Enable Register (Register 16). . . . . . . . . . . . . . . . . 195 TBR17: 10BASE-T PHY Control/Status Register (Register 17) . . . . . . . . . . . . . . . . . . . . . . . . . . 196 TBR19: 10BASE-T PHY Management Extension Register (Register 19) . . . . . . . . . . . . . . . . . . . 197 Reserved Register: 10BASE-T Configuration Register (Register 22) . . . . . . . . . . . . . . . . . . . . . . .197 Reserved Register: 10BASE-T Carrier Status Register (Register 23). . . . . . . . . . . . . . . . . . . . . . .197 TBR24: 10BASE-T Summary Status Register (Register 24) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .197 Initialization Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198 RLEN and TLEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .198 RDRA and TDRA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .199 LADRF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .199 PADR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .199 Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .199 Receive Descriptors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200 RMD0. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .201 RMD1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .201 RMD2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .202 RMD3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .203 Transmit Descriptors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .203 TMD0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .204 TMD1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .204 TMD2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .205 TMD3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .206 REGISTER SUMMARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .207 PCI Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .207 Control and Status Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .208 Bus Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .212 10BASE-T PHY Management Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .213 1 Mbps HomePNA PHY Management Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .214 REGISTER PROGRAMMING SUMMARY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .215 Am79C978 Programmable Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .215 ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .220 OPERATING RANGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .220 DC CHARACTERISTICS OVER COMMERCIAL OPERATING RANGES UNLESS OTHERWISE SPECIFIED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .220 SWITCHING CHARACTERISTICS: BUS INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .222 10BASE-T Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .224 Power Supply Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .224 External Clock (XTAL) Timing Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .225 External Clock (Oscillator) Timing Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .225 PMD Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .225 PECL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .225 10BASE-T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227 SWITCHING CHARACTERISTICS: MEDIA INDEPENDENT INTERFACE . . . . . . . . . . . . . . . . . . . . . . .228 SWITCHING WAVEFORMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .229 Key to Switching Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .229 SWITCHING TEST CIRCUITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .229 SWITCHING WAVEFORMS: SYSTEM BUS INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230 SWITCHING WAVEFORMS: MEDIA INDEPENDENT INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . .234 PHYSICAL DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .236 PQL144 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .236 PQR160 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .237 APPENDIX A: ALTERNATIVE METHOD FOR INITIALIZATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1 APPENDIX B: LOOK-AHEAD PACKET PROCESSING (LAPP) CONCEPT . . . . . . . . . . . . . . . . . . . B-1 INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INDEX-1 Am79C978 11 LIST OF FIGURES Figure 1. Media Independent Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Figure 2. Frame Format at the MII Interface Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Figure 3. Slave Configuration Read. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Figure 4. Slave Configuration Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Figure 5. Slave Read Using I/O Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Figure 6. Slave Write Using Memory Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Figure 7. Expansion ROM Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Figure 8. Disconnect of Slave Cycle When Busy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Figure 9. Disconnect of Slave Burst Transfer - No Host Wait States . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Figure 10. Disconnect of Slave Burst Transfer - Host Inserts Wait States. . . . . . . . . . . . . . . . . . . . . . 41 Figure 11. Address Parity Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Figure 12. Slave Cycle Data Parity Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Figure 13. Bus Acquisition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Figure 14. Non-Burst Read Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Figure 15. Burst Read Transfer (EXTREQ = 0, MEMCMD = 0). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Figure 16. Non-Burst Write Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Figure 17. Burst Write Transfer (EXTREQ = 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Figure 18. Disconnect With Data Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Figure 19. Disconnect Without Data Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Figure 20. Target Abort . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Figure 21. Preemption During Non-Burst Transaction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Figure 22. Preemption During Burst Transaction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Figure 23. Master Abort . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Figure 24. Master Cycle Data Parity Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Figure 25. Initialization Block Read In Non-Burst Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Figure 26. Initialization Block Read In Burst Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Figure 27. Descriptor Ring Read In Non-Burst Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Figure 28. Descriptor Ring Read In Burst Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Figure 29. Descriptor Ring Write In Non-Burst Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Figure 30. Descriptor Ring Write In Burst Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Figure 31. FIFO Burst Write at Start of Unaligned Buffer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Figure 32. FIFO Burst Write at End of Unaligned Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Figure 33. 16-Bit Software Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Figure 34. 32-Bit Software Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Figure 35. ISO 8802-3 (IEEE/ANSI 802.3) Data Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Figure 36. IEEE 802.3 Frame and Length Field Transmission Order . . . . . . . . . . . . . . . . . . . . . . . . . 73 Figure 37. HomePNA PHY Framing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Figure 38. AID Symbol Transmit Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Figure 39. AID Symbol Receive Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Figure 40. Transmit Data Symbol Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Figure 41. Receive Symbol Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Figure 42. RLL 25 Coding Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Figure 43. Block Diagram No SRAM Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Figure 44. Block Diagram Low Latency Receive Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 Figure 45. LED Control Logic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 Figure 46. OnNow Functional Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Figure 47. Pattern Match RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Figure 48. NAND Tree Circuitry (160 PQFP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Figure 49. NAND Tree Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 Figure 50. 10BASE-T Transmit and Receive Data Paths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 Figure 51. Address Match Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 Figure 52. Clock Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 Figure 53. PMD Interface Timing (PECL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .225 Figure 54. 10 Mbps Transmit (TX) Timing Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .226 Figure 55. 10 Mbps Receive (RX) Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .226 Figure 56. Normal and Tri-State Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229 Figure 57. CLK Waveform for 5 V Signaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230 Figure 58. CLK Waveform for 3.3 V Signaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230 12 Am79C978 Figure 59. Input Setup and Hold Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230 Figure 60. Output Valid Delay Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231 Figure 61. Output Tri-State Delay Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231 Figure 62. EEPROM Read Functional Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231 Figure 63. Automatic PREAD EEPROM Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232 Figure 64. JTAG (IEEE 1149.1) TCK Waveform for 5 V Signaling. . . . . . . . . . . . . . . . . . . . . . . . . . . 232 Figure 65. JTAG (IEEE 1149.1) Test Signal Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233 Figure 66. Transmit Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234 Figure 67. Receive Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234 Figure 68. MDC Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234 Figure 69. Management Data Setup and Hold Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235 Figure 70. Management Data Output Valid Delay Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235 Figure B-1. LAPP Timeline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4 Figure B-2. LAPP 3 Buffer Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5 Figure B-3. LAPP Timeline for Two-Interrupt Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-9 Figure B-4. LAPP 3 Buffer Grouping for Two-interrupt Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-10 LIST OF TABLES Table 1. Interrupt Flags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Table 2. External Clock/Crystal Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Table 3. PCI Device ID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Table 4. PCI Software Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Table 5. Slave Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Table 6. Slave Configuration Transfers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Table 7. Master Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Table 8. Descriptor Read Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Table 9. Descriptor Write Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Table 10. Receive Address Match . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Table 11. HomePNA PHY Pulse Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Table 12. Access ID Symbol Pulse Positions and Encoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Table 13. Blanking Interval Speed Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Table 14. Master Station Control Word Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Table 15. MII Control Frame Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Table 16. EEPROM Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 Table 17. LED Default Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 Table 18. IEEE 1149.1 Supported Instruction Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Table 19. BSR Mode Of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Table 20. Device ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Table 21. NAND Tree Pin Sequence (160 PQFP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 Table 22. NAND Tree Pin Sequence (144 TQFP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 Table 24. PCI Configuration Space Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 Table 25. I/O Map in Word I/O Mode (DWIO = 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Table 26. Legal I/O Accesses in Word I/O Mode (DWIO = 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Table 27. I/O Map in DWord I/O Mode (DWIO = 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 Table 28. Legal I/O Accesses in Double Word I/O Mode (DWIO =1). . . . . . . . . . . . . . . . . . . . . . . . . . 98 Table 29. Auto-Negotiation Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 Table 30. Loopback Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 Table 31. Software Styles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 Table 32. Receive Watermark Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 Table 33. Transmit Start Point Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 Table 34. Transmit Watermark Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 Table 35. BCR Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 Table 36. ROMTNG Programming Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 Table 37. PHY Select Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158 Table 38. EEDET Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161 Table 39. Interface Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161 Table 40. Software Styles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 Table 41. SRAM_BND Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 Table 42. EBCS Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 Table 43. CLK_FAC Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 Am79C978 13 Table 44. FMDC Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 45. APDW Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 46. HPR0: HomePNA PHY MII Control (Register 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 47. HPR1: HomePNA PHY MII Status (Register 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 48. HPR2 and HPR3: HomePNA PHY MII ID (Registers 2 and 3). . . . . . . . . . . . . . . . . . . . . . Table 49. HPR4-HPR7: HomePNA PHY Auto-Negotiation (Registers 4 - 7) . . . . . . . . . . . . . . . . . . . Table 50. HPR16: HomePNA PHY Control (Register 16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 51. HPR17: HomePNA Status Control (Register 17) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 52. HPR18 and HPR19: HomePNA PHY TxCOMM (Registers 18 and 19). . . . . . . . . . . . . . . Table 53. HPR20 and HPR21: HomePNA PHY RxCOMM (Registers 20 and 21) . . . . . . . . . . . . . . Table 54. HPR22: HomePNA PHY AID (Register 22) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 55. HPR23: HomePNA PHY Noise Control (Register 23) . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 56. HPR24: HomePNA PHY Noise Control 2 (Register 24). . . . . . . . . . . . . . . . . . . . . . . . . . . Table 57. HPR25: HomePNA PHY Noise Statistics (Register 25) . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 58. HPR26: HomePNA PHY Event Status (Register 26) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 59. HPR27: HomePNA PHY Event Status (Register 27) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 60. HPR8: HomePNA PHY ISBI Control (Register 28) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 61. HPR29: HomePNA PHY TX Control (Register 29) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 62. HPR30: HomePNA PHY Drive Level Control Test Register (Register 30) . . . . . . . . . . . . . Table 63. HPR31: HomePNA PHY Analog Control Register (Register 31) . . . . . . . . . . . . . . . . . . . . Table 64. Am79C978 10BASE-T PHY Management Register Set . . . . . . . . . . . . . . . . . . . . . . . . . . Table 65. TBR0: 10BASE-T PHY Control Register (Register 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 66. TBR1: 10BASE-T PHY Status Register (Register 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 67. TBR2: 10BASE-T PHY Identifier (Register 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 68. TBR3: 10BASE-T PHY Identifier (Register 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 69. TBR4: 10BASE-T Auto-Negotiation Advertisement Register (Register 4) . . . . . . . . . . . . . Table 70. TBR5: 10BASE-T Auto-Negotiation Link Partner Ability Register (Register 5) - Base Page Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 71. TBR5: 10BASE-T Auto-Negotiation Link Partner Ability Register (Register 5) - Next Page Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 72. TBR6: 10BASE-T Auto-Negotiation Expansion Register (Register 6) . . . . . . . . . . . . . . . . Table 73. TBR7: 10BASE-T Auto-Negotiation Next Page Register (Register 7) . . . . . . . . . . . . . . . . Table 74. TBR16: 10BASE-T INTERRUPT Status and Enable Register (Register 16) . . . . . . . . . . . Table 75. TBR17: 10BASE-T PHY Control/Status Register (Register 17). . . . . . . . . . . . . . . . . . . . . Table 76. TBR19: 10BASE-T PHY Management Extension Register (Register 19) . . . . . . . . . . . . . Table 77. TBR24: 10BASE-T Summary Status Register (Register 24) . . . . . . . . . . . . . . . . . . . . . . . Table 78. Initialization Block (SSIZE32 = 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 79. Initialization Block (SSIZE32 = 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 80. R/TLEN Decoding (SSIZE32 = 0). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 81. R/TLEN Decoding (SSIZE32 = 1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 82. Receive Descriptor (SWSTYLE = 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 83. Receive Descriptor (SWSTYLE = 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 84. Receive Descriptor (SWSTYLE = 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 85. Transmit Descriptor (SWSTYLE = 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 86. Transmit Descriptor (SWSTYLE = 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 87. Transmit Descriptor (SWSTYLE = 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 88. PCI Configuration Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 89. Control and Status Registers (CSRs). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 90. Bus Configuration Registers (BCRs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 91. 10BASE-T PHY Management Registers (TBRs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 92. 1 Mbps HomePNA PHY Management Registers (HPRs) . . . . . . . . . . . . . . . . . . . . . . . . . Table 93. Control and Status Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 94. Bus Configuration Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table A-1. Registers for Alternative Initialization Method (Note 1). . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Am79C978 169 169 179 180 181 181 182 183 183 184 184 184 185 185 186 186 186 187 187 187 188 189 190 191 191 192 193 193 194 194 195 196 197 197 198 198 199 199 200 200 200 203 203 203 207 208 212 213 214 215 217 A-1 RELATED AMD PRODUCTS Part No. Description Controllers Am79C90 CMOS Local Area Network Controller for Ethernet (C-LANCE) Integrated Controllers Am79C930 PCnetTM-Mobile Single Chip Wireless LAN Media Access Controller Am79C940B Media Access Controller for Ethernet (MACETM) Am79C961A PCnet-ISA II Full Duplex Single-Chip Ethernet Controller for ISA Bus Am79C965A PCnet-32 Single-Chip 32-Bit Ethernet Controller for 486 and VL Buses Am79C970A PCnet-PCI II Full Duplex Single-Chip Ethernet Controller for PCI Local Bus Am79C971 PCnet-FAST Single-Chip Full-Duplex 10/100 Mbps Ethernet Controller for PCI Local Bus Am79C972 PCnet-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support Manchester Encoder/Decoder Am7992B Serial Interface Adapter (SIA) Physical Layer Devices (Single-Port) Am7996 IEEE 802.3/Ethernet/Cheapernet Transceiver (TAP) Am79761 Physical Layer 10-Bit Transceiver for Gigabit Ethernet (GigaPHYTM-SD) Am79C98 Twisted Pair Ethernet Transceiver (TPEX) Am79C100 Twisted Pair Ethernet Transceiver Plus (TPEX+) Am79C873 10/100 Mbps Ethernet Physical Layer Transceiver (NetPHYTM-1) Physical Layer Devices (Multi-Port) Am79C871 Quad Fast Ethernet Transceiver for 100BASE-X Repeaters (QFEXrTM) Am79C988B Quad Integrated Ethernet Transceiver (QuIETTM) Am79C989 Quad Ethernet Switching Transceiver (QuESTTM) Integrated Repeater/Hub Devices Am79C981 Integrated Multiport Repeater Plus (IMR+) Am79C982 Basic Integrated Multiport Repeater (bIMR) Am79C983A Integrated Multiport Repeater 2 (IMR2TM) Am79C984A Enhanced Integrated Multiport Repeater (eIMRTM) Am79C985 Enhanced Integrated Multiport Repeater Plus (eIMR+TM) Am79C987 Hardware Implemented Management Information Base (HIMIBTM) Am79C978 15 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 C/BE3 AD24 AD25 VSSB AD26 VDD_PCI AD27 AD28 AD29 AD30 VSS VSSB AD31 VDD_PCI REQ GNT PCI_CLK RST INTA PG VDD TDI VSSB TDO VDDB TMS TCK PME VSS EECS VSSB EESK/LED1 LED2 VDDB EEDI/LED0 EEDO/LED3 CONNECTION DIAGRAM (144 TQFP) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Am79C978 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 RXDVDDRX RX+ DVSSX TXDVDDTX TX+ DVDDD IREF DVSSD DVSSA DVDDA PHY_RST DVDDA_HR VSSB VDDB HRTRXP VDDHR HRTRXN VSSHR VDDCO XTAL1 XTAL2 VSS VDD XCLK/XTAL LED4 MDIO VSSB MDC RXD3 RXD2 VDDB RXD1 RXD0 VSS AD11 VDD_PCI AD10 AD9 AD8 C/BE0 VSSB AD7 VDD_PCI AD6 AD5 VDD AD4 AD3 VSSB AD2 VDD_PCI AD1 AD0 VSS VDD CRS VSSB COL TXD3 TXD2 TXD1 VDD VDDB TXD0 TX_EN TX_CLK VSSB RX_ER RX_CLK RX_DV 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 IDSEL AD23 VSSB AD22 VDD_PCI AD21 AD20 VDD AD19 AD18 VSSB AD17 VDD_PCI AD16 C/BE2 VSS FRAME IRDY VSSB TRDY VDD_PCI DEVSEL STOP VDD PERR SERR VSSB PAR VDD_PCI C/BE1 AD15 VSS AD14 AD13 VSSB AD12 22206B-2 16 Am79C978 160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 NC NC C/BE3 AD24 AD25 VSSB AD26 VDD_PCI AD27 AD28 AD29 AD30 VSS VSSB AD31 VDD_PCI REQ GNT PCI_CLK RST INTA PG VDD TDI VSSB TDO VDDB TMS TCK PME VSS EECS VSSB EESK/LED1 LED2 VDDB EEDI/LED0 EEDO/LED3 NC NC CONNECTION DIAGRAM (160 PQFP) Am79C978 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 RXDVDDRX RX+ DVSSX TXDVDDTX TX+ DVDDD IREF DVSSD DVSSA DVDDA PHY_RST DVDDA_HR VSSB VDDB HRTRXP VDDHR HRTRXN VSSHR VDDCO XTAL1 XTAL2 VSS VDD XCLK/XTAL LED4 MDIO VSSB MDC RXD3 RXD2 VDDB RXD1 RXD0 VSS NC NC NC NC 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 NC NC AD11 VDD_PCI AD10 AD9 AD8 C/BE0 VSSB AD7 VDD_PCI AD6 AD5 VDD AD4 AD3 VSSB AD2 VDD_PCI AD1 AD0 VSS VDD CRS VSSB COL TXD3 TXD2 TXD1 VDD VDDB TXD0 TX_EN TX_CLK VSSB RX_ER RX_CLK RX_DV NC NC NC NC IDSEL AD23 VSSB AD22 VDD_PCI AD21 AD20 VDD AD19 AD18 VSSB AD17 VDD_PCI AD16 C/BE2 VSS FRAME IRDY VSSB TRDY VDD_PCI DEVSEL STOP VDD PERR SERR VSSB PAR VDD_PCI C/BE1 AD15 VSS AD14 AD13 VSSB AD12 NC NC 22206B-3 Am79C978 17 PIN DESIGNATIONS (PQL144) Listed By Pin Number Pin No. Pin Name Pin No. Pin Name Pin No. Pin Name Pin No. Pin Name 1 2 IDSEL AD23 37 38 AD11 VDD_PCI 73 74 VSS RXD0 109 110 EEDO/LED3 EEDI/LED0 3 4 VSSB AD22 39 40 AD10 AD9 75 76 RXD1 VDDB 111 112 VDDB LED2 5 6 VDD_PCI AD21 41 42 AD8 C/BE0 77 78 RXD2 RXD3 113 114 EESK/LED1 VSSB 7 8 AD20 VDD 43 44 VSSB AD7 79 80 MDC VSSB 115 116 EECS VSS 9 10 AD19 AD18 45 46 VDD_PCI AD6 81 82 MDIO LED4 117 118 PME TCK 11 12 VSSB AD17 47 48 AD5 VDD 83 84 XCLK/XTAL VDD 119 120 TMS VDDB 13 14 VDD_PCI AD16 49 50 AD4 AD3 85 86 VSS XTAL2 121 122 TDO VSSB 15 16 C/BE2 VSS 51 52 VSSB AD2 87 88 XTAL1 VDDCO 123 124 TDI VDD 17 18 FRAME IRDY 53 54 VDD_PCI AD1 89 90 VSSHR HRTRXN 125 126 PG INTA 19 20 VSSB TRDY 55 56 AD0 VSS 91 92 VDDHR HRTRXP 127 128 RST PCI_CLK 21 VDD_PCI 57 VDD 93 VDDB 129 GNT 22 23 DEVSEL STOP 58 59 CRS VSSB 94 95 VSSB DVDDA_HR 130 131 REQ VDD_PCI 24 25 VDD PERR 60 61 COL TXD3 96 97 PHY_RST DVDDA 132 133 AD31 VSSB 26 27 SERR VSSB 62 63 TXD2 TXD1 98 99 DVSSA DVSSD 134 135 VSS AD30 28 29 PAR VDD_PCI 64 65 VDD VDDB 100 101 IREF DVDDD 136 137 AD29 AD28 30 31 C/BE1 AD15 66 67 TXD0 TX_EN 102 103 TX+ DVDDTX 138 139 AD27 VDD_PCI 32 33 VSS AD14 68 69 TX_CLK VSSB 104 105 TXDVSSX 140 141 AD26 VSSB 34 35 AD13 VSSB 70 71 RX_ER RX_CLK 106 107 RX+ DVDDRX 142 143 AD25 AD24 36 AD12 72 RX_DV 108 RX- 144 C/BE3 18 Am79C978 PIN DESIGNATIONS (PQR160) Listed By Pin Number Pin No. Pin Name Pin No. Pin Name Pin No. Pin Name Pin No. Pin Name 1 2 NC NC 41 42 NC NC 81 82 NC NC 121 122 NC NC 3 4 IDSEL AD23 43 44 AD11 VDD_PCI 83 84 NC NC 123 124 EEDO/LED3 EEDI/LED0 5 6 VSSB AD22 45 46 AD10 AD9 85 86 VSS RXD0 125 126 VDDB LED2 7 8 VDD_PCI AD21 47 48 AD8 C/BE0 87 88 RXD1 VDDB 127 128 EESK/LED1 VSSB 9 10 AD20 VDD 49 50 VSSB AD7 89 90 RXD2 RXD3 129 130 EECS VSS 11 12 AD19 AD18 51 52 VDD_PCI AD6 91 92 MDC VSSB 131 132 PME TCK 13 14 VSSB AD17 53 54 AD5 VDD 93 94 MDIO LED4 133 134 TMS VDDB 15 16 VDD_PCI AD16 55 56 AD4 AD3 95 96 XCLK/XTAL VDD 135 136 TDO VSSB 17 18 C/BE2 VSS 57 58 VSSB AD2 97 98 VSS XTAL2 137 138 TDI VDD 19 20 FRAME IRDY 59 60 VDD_PCI AD1 99 100 XTAL1 VDDCO 139 140 PG INTA 21 VSSB 61 AD0 101 VSSHR 141 RST 22 23 TRDY VDD_PCI 62 63 VSS VDD 102 103 HRTRXN VDDHR 142 143 PCI_CLK GNT 24 25 DEVSEL STOP 64 65 CRS VSSB 104 105 HRTRXP VDDB 144 145 REQ VDD_PCI 26 27 VDD PERR 66 67 COL TXD3 106 107 VSSB DVDDA_HR 146 147 AD31 VSSB 28 29 SERR VSSB 68 69 TXD2 TXD1 108 109 PHY_RST DVDDA 148 149 VSS AD30 30 31 PAR VDD_PCI 70 71 VDD VDDB 110 111 DVSSA DVSSD 150 151 AD29 AD28 32 33 C/BE1 AD15 72 73 TXD0 TX_EN 112 113 IREF DVDDD 152 153 AD27 VDD_PCI 34 35 VSS AD14 74 75 TX_CLK VSSB 114 115 TX+ DVDDTX 154 155 AD26 VSSB 36 37 AD13 VSSB 76 77 RX_ER RX_CLK 116 117 TXDVSSX 156 157 AD25 AD24 38 39 AD12 NC 78 79 RX_DV NC 118 119 RX+ DVDDRX 158 159 C/BE3 NC 40 NC 80 NC 120 RX- 160 NC Am79C978 19 PIN DESIGNATIONS (PQL144) Listed By Group Pin Name Pin Function Type Voltage Driver No. of Pins HomePNA PHY Network Ports HRTXRXP/N Receive/Transmit Data I/O 3.3 NA 2 XTAL1 Crystal Input (20 MHz XTAL/60 MHz CLK) I 3.3 - 1 XTAL2 Crystal Output (20 MHz XTAL) O 3.3 XTAL 1 XCLK/XTAL Oscillator/Crystal Select I 3.3 - 1 10BASE-T Network Ports TX Serial Transmit Data O 3.3 NA 2 RX Serial Receive Data I 3.3 - 2 IREF Tied to GND via a 12 k 1% resistor I 3.3 - 1 PHY_RST Buffered PCI RST signal O 3.3 OMII1 1 TX_CLK MII Transmit Clock I 3.3 - 1 TXD[3:0] MII Transmit Data O 3.3 OMII1 4 TX_EN MII Transmit Enable O 3.3 OMII1 1 RX_CLK MII Receive Clock I 3.3 - 1 RXD[3:0] MII Receive Data I 3.3 - 4 RX_ER MII Receive Error I 3.3 - 1 RX_DV MII Receive Data Valid I 3.3 - 1 MDC MII Management Data Clock O 3.3 OMII2 1 MDIO MII Management Data I/O I/O 3.3 TSMII 1 CRS Carrier Sense I 3.3 - 1 COL Collision I 3.3 - 1 PME Power Management Event O 3.3 OD6 1 PG Power Good I 3.3 - 1 PCI_CLK CPU Clock I 3.3/5 - 1 C/BE[3:0] Bus Command Byte Enable I/O 3.3/5 TS3 4 AD[31:0] Address/Data I/O 3.3/5 TS3 32 DEVSEL Device Select I/O 3.3/5 STS6 1 FRAME Cycle Frame I/O 3.3/5 STS6 1 GNT Bus Grant I 3.3/5 - 1 IDSEL Initialization Device Select I 3.3/5 - 1 INTA Interrupt O 3.3/5 OD6 1 IRDY Initiator Ready I/O 3.3/5 STS6 1 PAR Parity I/O 3.3/5 STS6 1 PERR Parity Error I/O 3.3/5 STS6 1 REQ Bus Request O 3.3/5 TS3 1 RST Reset I 3.3/5 - 1 SERR System Error I/O 3.3/5 OD6 1 MII Magic Packet Host CPU Interface 20 Am79C978 Pin Name Pin Function Type Voltage Driver No. of Pins STOP Stop I/O 3.3/5 STS6 1 TRDY Target Ready I/O 3.3/5 STS6 1 EEPROM/LED Interface EECS Chip Select O 3.3 O6 1 EEDI/LED0 Data In/LED0 I/O 3.3 LED 1 EESK/LED1 Serial Clock/LED1 O 3.3 LED 1 LED2 LED2 O 3.3 LED 1 EEDO/LED3 Data Out/LED3 O 3.3 LED 1 LED4 LED4 O 3.3 LED 1 Test Access Port Interface (JTAG) TCLK Test Clock I 3.3 - 1 TMS Test Mode Select I 3.3 - 1 TDI Test Data In I 3.3 - 1 TDO Test Data Out O 3.3 TS6 1 DVDDTX Transceiver Digital Power P 3.3 - 1 DVDDRX Transceiver Digital Power P 3.3 - 1 VDD_PCI Digital power for the PCI bus P 3.3 - 9 VDDB Digital power for the PCI bus P 3.3 - 5 VDD Digital power P 3.3 - 7 VDDHR Digital power for HomePNA PHY P 3.3 - 1 DVDDA Transceiver Analog Power P 3.3 - 1 DVDDD Transceiver Digital Power P 3.3 - 1 VDDCO Crystal Oscillator Power P 3.3 - 1 DVDDA_HR Transceiver Analog Power P 3.3 - 1 DVSSD Transceiver Digital Ground G 0 - 1 DVSSA Transceiver Analog Ground G 0 - 1 DVSSX Transceiver Ground G 0 - 1 VSSB Digital I/O Ground G 0 - 15 VSS Digital Ground G 0 - 7 VSSHR HomePNA PHY Analog Ground G 0 - 1 Power/Ground Am79C978 21 PIN DESIGNATIONS (PQR160) Listed By Group Pin Name Pin Function Type Voltage Driver No. of Pins HomePNA PHY Network Ports HRTXRXP/N Receive/Transmit Data I/O 3.3 NA 2 XTAL1 Crystal Input (20 MHz XTAL/60 MHz CLK) I 3.3 - 1 XTAL2 Crystal Output (20 MHz XTAL) O 3.3 XTAL 1 XCLK/XTAL Oscillator/Crystal Select I 3.3 - 1 10BASE-T Network Ports TX Serial Transmit Data O 3.3 NA 2 RX Serial Receive Data I 3.3 - 2 IREF Tied to GND via a 12 k 1% resistor I 3.3 - 1 PHY_RST Buffered PCI RST signal O 3.3 OMII1 1 TX_CLK MII Transmit Clock I 3.3 - 1 TXD[3:0] MII Transmit Data O 3.3 OMII1 4 TX_EN MII Transmit Enable O 3.3 OMII1 1 RX_CLK MII Receive Clock I 3.3 - 1 RXD[3:0] MII Receive Data I 3.3 - 4 RX_ER MII Receive Error I 3.3 - 1 RX_DV MII Receive Data Valid I 3.3 - 1 MDC MII Management Data Clock O 3.3 OMII2 1 MDIO MII Management Data I/O I/O 3.3 TSMII 1 CRS Carrier Sense I 3.3 - 1 COL Collision I 3.3 - 1 PME Power Management Event O 3.3 OD6 1 PG Power Good I 3.3 - 1 PCI_CLK CPU Clock I 3.3/5 - 1 C/BE[3:0] Bus Command Byte Enable I/O 3.3/5 TS3 4 AD[31:0] Address/Data I/O 3.3/5 TS3 32 DEVSEL Device Select I/O 3.3/5 STS6 1 FRAME Cycle Frame I/O 3.3/5 STS6 1 GNT Bus Grant I 3.3/5 - 1 IDSEL Initialization Device Select I 3.3/5 - 1 INTA Interrupt O 3.3/5 OD6 1 IRDY Initiator Ready I/O 3.3/5 STS6 1 PAR Parity I/O 3.3/5 STS6 1 PERR Parity Error I/O 3.3/5 STS6 1 REQ Bus Request O 3.3/5 TS3 1 RST Reset I 3.3/5 - 1 SERR System Error I/O 3.3/5 OD6 1 MII Magic Packet Host CPU Interface 22 Am79C978 Pin Name Pin Function Type Voltage Driver No. of Pins STOP Stop I/O 3.3/5 STS6 1 TRDY Target Ready I/O 3.3/5 STS6 1 EEPROM/LED Interface EECS Chip Select O 3.3 O6 1 EEDI/LED0 Data In/LED0 I/O 3.3 LED 1 EESK/LED1 Serial Clock/LED1 O 3.3 LED 1 LED2 LED2 O 3.3 LED 1 EEDO/LED3 Data Out/LED3 O 3.3 LED 1 LED4 LED4 O 3.3 LED 1 Test Access Port Interface (JTAG) TCLK Test Clock I 3.3 - 1 TMS Test Mode Select I 3.3 - 1 TDI Test Data In I 3.3 - 1 TDO Test Data Out O 3.3 TS6 1 DVDDTX Transceiver Digital Power P 3.3 - 1 DVDDRX Transceiver Digital Power P 3.3 - 1 VDD_PCI Digital power for the PCI bus P 3.3 - 9 VDDB Digital power for the PCI bus P 3.3 - 5 VDD Digital power P 3.3 - 7 VDDHR Digital power for HomePNA PHY P 3.3 - 1 DVDDA Transceiver Analog Power P 3.3 - 1 DVDDD Transceiver Digital Power P 3.3 - 1 VDDCO Crystal Oscillator Power P 3.3 - 1 DVDDA_HR Transceiver Analog Power P 3.3 - 1 DVSSD Transceiver Digital Ground G 0 - 1 DVSSA Transceiver Analog Ground G 0 - 1 DVSSX Transceiver Ground G 0 - 1 VSSB Digital I/O Ground G 0 - 15 VSS Digital Ground G 0 - 7 VSSHR HomePNA PHY Analog Ground G 0 - 1 Power/Ground Am79C978 23 PIN DESIGNATIONS Listed By Driver Type The following table describes the various types of output drivers used in the Am79C978 controller. All IOL and IOH values shown in the table apply to 3.3 V signaling. Driver Name A sustained tri-state signal is a low active signal that is driven high for one clock period before it is left floating. TX is a differential output driver. Its characteristics and those of XTAL2 output are described in the DC CHARACTERISTICS section. Type IOL (mA) IOH (mA) Load (pF) LED LED 12 0.4 50 O6 Totem Pole 6 0.4 50 OD6 Open Drain 6 NA 50 TS3 Tri-State 3 2 50 TS6 Tri-State 6 2 50 STS6 Sustained Tri-State 6 2 50 OMII1 Tri-State 4 4 50 OMII2 Tri-State 4 4 390 TSMII Tri-State 4 4 470 For typical 5 V DC characteristics, please refer to DC Characteristics Over Commercial Operating Ranges section. 24 Am79C978 ORDERING INFORMATION Standard Products AMD standard products are available in several packages and operating ranges. The order number (Valid Combination) is formed by a combination of the elements below. Am79C978 K\V C \W ALTERNATE PACKAGING OPTION \W = Trimmed and formed in a tray TEMPERATURE RANGE C = Commercial (0 C to +70 C) PACKAGE TYPE K = Plastic Quad Flat Pack (PQR160) V = Thin Quad Flat Pack (PQL144) SPEED OPTION Not applicable DEVICE NUMBER/DESCRIPTION Am79C978 PCnet-Home Single-Chip 1/10 Mbps PCI Home Networking Controller Valid Combinations Am79C978 KC\W VC\W Valid Combinations Valid Combinations list configurations planned to be supported in volume for this device. Consult the local AMD sales office to confirm availability of specific valid combinations and to check on newly released combinations. Am79C978 25 PIN DESCRIPTIONS PCI Interface AD[31:0] Address and Data support a clock frequency of 0 MHz after certain precautions are taken to ensure data integrity. This clock or a derivation is not used to drive any network functions. Input/Output Address and data are multiplexed on the same bus interface pins. During the first clock of a transaction, AD[31:0] contain a physical address (32 bits). During the subsequent clocks, AD[31:0] contain data. Byte ordering is little endian by default. AD[7:0] are defined as the least significant byte (LSB) and AD[31:24] are defined as the most significant byte (MSB). For FIFO data transfers, the Am79C978 controller can be programmed for big endian byte ordering. See CSR3, bit 2 (BSWP) for more details. During the address phase of the transaction, when the Am79C978 controller is a bus master, AD[31:2] will add r e s s t h e a c t i v e D o u bl e Wo r d ( D Wo r d ) . T h e Am79C978 controller always drives AD[1:0] to '00' during the address phase indicating linear burst order. When the Am79C978 controller is not a bus master, the AD[31:0] lines are continuously monitored to determine if an address match exists for slave transfers. During the data phase of the transaction, AD[31:0] are driven by the Am79C978 controller when performing bus master write and slave read operations. Data on AD[31:0] is latched by the Am79C978 controller when performing bus master read and slave write operations. When RST is active, AD[31:0] are inputs for NAND tree testing. C/BE[3:0] Bus Command and Byte Enables Input/Output When RST is active, C/BE[3:0] are inputs for NAND tree testing. PCI_CLK Input This clock is used to drive the system bus interface and the internal buffer management unit. All bus signals are sampled on the rising edge of PCI_CLK and all parameters are defined with respect to this edge. The Am79C978 controller normally operates over a frequency range of 10 to 33 MHz on the PCI bus due to networking demands. The Am79C978 controller will 26 DEVSEL Device Select Input/Output The Am79C978 controller drives DEVSEL LOW when it detects a transaction that selects the device as a target. The device samples DEVSEL to detect if a target claims a transaction that the Am79C978 controller has initiated. When RST is active, DEVSEL is an input for NAND tree testing. FRAME Cycle Frame Input/Output FRAME is driven by the Am79C978 controller when it is the bus master to indicate the beginning and duration of a transaction. FRAME is asserted to indicate a bus transaction is beginning. FRAME is asserted while data transfers continue. FRAME is deasserted before the final data phase of a transaction. When the Am79C978 controller is in slave mode, it samples FRAME to determine the address phase of a transaction. When RST is active, FRAME is an input for NAND tree testing. GNT Bus Grant Bus command and byte enables are multiplexed on the same bus interface pins. During the address phase of the transaction, C/BE[3:0] define the bus command. During the data phase, C/BE[3:0] are used as byte enables. The byte enables define which physical byte lanes carry meaningful data. C/BE0 applies to byte 0 (AD[7:0]) and C/BE3 applies to byte 3 (AD[31:24]). The function of the byte enables is independent of the byte ordering mode (BSWP, CSR3, bit 2). Clock When RST is active, PCI_CLK is an input for NAND tree testing. Input This signal indicates that the access to the bus has been granted to the Am79C978 controller. The Am79C978 controller supports bus parking. When the PCI bus is idle and the system arbiter asserts GNT without an active REQ from the Am79C978 controller, the device will drive the AD[31:0], C/BE[3:0], and PAR lines. When RST is active, GNT is an input for NAND tree testing. IDSEL Initialization Device Select Input This signal is used as a chip select for the Am79C978 controller during configuration read and write transactions. When RST is active, IDSEL is an input for NAND tree testing. Am79C978 INTA IRDY Interrupt Request Output An attention signal which indicates that one or more of the following status flags is set: EXDINT, IDON, MERR, MISS, MFCO, MPINT, RCVCCO, RINT, SINT, TINT, TXSTRT, UINT, MCCINT, MPDTINT, MAPINT, MREINT, and STINT. Each status flag has either a mask or an enable bit which allows for suppression of INTA assertion. Table 1 shows the flag descriptions. By default INTA is an open-drain output. For applications that need a high-active edge-sensitive interrupt signal, the INTA pin can be configured for this mode by setting INTLEVEL (BCR2, bit 7) to Table 1. When RST is active, INTA is the output for NAND tree testing. Table 1. Interrupt Flags Initiator Ready Input/Output IRDY indicates the ability of the initiator of the transaction to complete the current data phase. IRDY is used in conjunction with TRDY. Wait states are inserted until both IRDY and TRDY are asserted simultaneously. A data phase is completed on any clock when both IRDY and TRDY are asserted. When the Am79C978 controller is a bus master, it asserts IRDY during all write data phases to indicate that valid data is present on AD[31:0]. During all read data phases, the device asserts IRDY to indicate that it is ready to accept the data. When the Am79C978 controller is the target of a transaction, it checks IRDY during all write data phases to determine if valid data is present on AD[31:0]. During all read data phases, the device checks IRDY to determine if the initiator is ready to accept the data. Name Description Mask Bit Interrupt Bit EXDINT Excessive Deferral CSR5, bit 6 CSR5, bit 7 IDON Initialization Done CSR3, bit 8 CSR0, bit 8 MERR Memory Error CSR3, bit 11 CSR0, bit 11 MISS Missed Frame CSR3, bit 12 CSR0, bit 12 MFCO Missed Frame Count OverCSR4, bit 8 flow CSR4, bit 9 MPINT Magic Packet Interrupt CSR5, bit 3 CSR5, bit 4 RCVCCO Receive Collision Count CSR4, bit 4 Overflow CSR4, bit 5 Parity is even parity across AD[31:0] and C/BE[3:0]. When the Am79C978 controller is a bus master, it generates parity during the address and write data phases. It checks parity during read data phases. When the Am79C978 controller operates in slave mode, it checks parity during every address phase. When it is the target of a cycle, it checks parity during write data phases and it generates parity during read data phases. RINT Receive Interrupt CSR3, bit 10 CSR0, bit 10 When RST is active, PAR is an input for NAND tree testing. SINT System Error CSR5, bit 10 CSR5, bit 11 PERR TINT Transmit Interrupt CSR3, bit 9 CSR0, bit 9 Parity Error TXSTRT Transmit Start CSR4, bit 2 CSR4, bit 3 UINT User Interrupt CSR4, bit 7 CSR4, bit 6 MCCINT MII Management Command Complete Interrupt CSR7, bit 4 CSR7, bit 5 MPDTINT MII PHY Detect CSR7, bit 0 Transition Interrupt CSR7, bit 1 MAPINT MII Auto-Poll Interrupt CSR7, bit 7 MREINT MII Management CSR7, bit 8 Frame Read Error Interrupt CSR7, bit 9 STINT Software Timer CSR7, bit 10 Interrupt CSR7, bit 11 CSR7, bit 6 When RST is active, IRDY is an input for NAND tree testing. PAR Parity Input/Output Input/Output During any slave write transaction and any master read transaction, the Am79C978 controller asserts PERR when it detects a data parity error and reporting of the error is enabled by setting PERREN (PCI Command register, bit 6) to 1. During any master write transaction, the Am79C978 controller monitors PERR to see if the target reports a data parity error. When RST is active, PERR is an input for NAND tree testing. REQ Bus Request Input/Output The Am79C978 controller asserts REQ pin as a signal that it wishes to become a bus master. REQ is driven high when the Am79C978 controller does not request the bus. In Power Management mode, the REQ pin will not be driven. Am79C978 27 When RST is active, REQ is an input for NAND tree testing. RST Reset Input When RST is asserted LOW and the PG pin is HIGH, then the Am79C978 controller performs an internal system reset of the type H_RESET (HARDWARE_RESET, see section on RESET). RST must be held for a minimum of 30 clock periods. While in the H_RESET state, the Am79C978 controller will disable or deassert all outputs. RST may be asynchronous to clock when asserted or deasserted. When the PG pin is LOW, RST disables all of the PCI pins except the PME pin. When RST is LOW and PG is HIGH, NAND tree testing is enabled. When RST is active, TRDY is an input for NAND tree testing. Magic Packet Interface PME Power Management Event Output, Open Drain PME is an output that can be used to indicate that a power management event (a Magic Packet, an OnNow pattern match, or a change in link state) has been detected. The PME pin is asserted when either 1. PME_STATUS and PME_EN are both 1, 2. PME_EN_OVR and MPMAT are both 1, or SERR System Error When the Am79C978 controller is the target of a transaction, it asserts TRDY during all read data phases to indicate that valid data is present on AD[31:0]. During all write data phases, the device asserts TRDY to indicate that it is ready to accept the data. 3. PME_EN_OVR and LCDET are both 1. Output During any slave transaction, the Am79C978 controller asserts SERR when it detects an address parity error, and reporting of the error is enabled by setting PERREN (PCI Command register, bit 6) and SERREN (PCI Command register, bit 8) to 1. The PME signal is asynchronous with respect to the PCI clock. See the Power Saving Mode section for detailed description. PG Power Good Input By default SERR is an open-drain output. For component test, it can be programmed to be an active-high totem-pole output. The PG pin has two functions: (1) it puts the device into Magic Packet mode, and (2) it blocks any resets when the PCI bus power is off. When RST is active, SERR is an input for NAND tree testing. When PG is LOW and either MPPEN or MPMODE is set to 1, the device enters Magic Packet mode. STOP When PG is LOW, a LOW assertion of the PCI RST pin will only cause the PCI interface pins (except for PME) to be put in the high impedance state. The internal logic will ignore the assertion of RST. Stop Input/Output In slave mode, the Am79C978 controller drives the STOP signal to inform the bus master to stop the current transaction. In bus master mode, the Am79C978 controller checks STOP to determine if the target wants to disconnect the current transaction. When PG is HIGH, assertion of the PCI RST pin causes the controller logic to be reset and the configuration information to be loaded from the EEPROM. When RST is active, STOP is an input for NAND tree testing. Note: PG input should be kept high during NAND tree testing. TRDY Board Interface Target Ready Input/Output TRDY indicates the ability of the target of the transaction to complete the current data phase. Wait states are inserted until both IRDY and TRDY are asserted simultaneously. A data phase is completed on any clock when both IRDY and TRDY are asserted. When the Am79C978 controller is a bus master, it checks TRDY during all read data phases to determine if valid data is present on AD[31:0]. During all write data phases, the device checks TRDY to determine if the target is ready to accept the data. 28 Note: Before programming the LED pins, see the description of LEDPE in BCR2, bit 12. LED0 LED0 Output This output is designed to directly drive an LED. By default, LED0 indicates an active link connection. This pin can also be programmed to indicate other network status (see BCR4). The LED0 pin polarity is programmable, but by default it is active LOW. When the LED0 pin polarity is programmed to active LOW, the output is an open drain driver. When the LED0 pin polarity is pro- Am79C978 grammed to active HIGH, the output is a totem pole driver. larity is programmed to active HIGH, the output is a totem pole driver. Note: The LED0 pin is multiplexed with the EEDI pin. Special attention must be given to the external circuitry attached to this pin. When this pin is used to drive an LED while an EEPROM is used in the system, then buffering may be required between the LED3 pin and the LED circuit. If an LED circuit were directly attached to this pin, it may create an IOL requirement that could not be met by the serial EEPROM attached to this pin. If no EEPROM is included in the system design or low current LEDs are used, then the LED3 signal may be directly connected to an LED without buffering. For more details regarding LED connection, see the section on LED Support. LED1 LED1 Output This output is designed to directly drive an LED. By default, LED1 indicates receive activity on the network. This pin can also be programmed to indicate other network status (see BCR5). The LED1 pin polarity is programmable, but by default, it is active LOW. When the LED1 pin polarity is programmed to active LOW, the output is an open drain driver. When the LED1 pin polarity is programmed to active HIGH, the output is a totem pole driver. Note: The LED1 pin is multiplexed with the EESK pin. The LED1 pin is also used during EEPROM AutoDetection to determine whether or not an EEPROM is present at the Am79C978 controller interface. At the last rising edge of CLK while RST is active LOW, LED1 is sampled to determine the value of the EEDET bit in BCR19. It is important to maintain adequate hold time around the rising edge of the CLK at this time to ensure a correctly sampled value. A sampled HIGH value means that an EEPROM is present, and EEDET will be set to 1. A sampled LOW value means that an EEPROM is not present, and EEDET will be set to 0. See the EEPROM Auto-Detection section for more details. If no LED circuit is to be attached to this pin, then a pullup or pull-down resistor must be attached in order to select the EEDET setting. WARNING: The input signal level of LED1 must be insured for correct EEPROM detection before the deassertion of RST. LED2 LED2 Output This output is designed to directly drive an LED. This pin can be programmed to indicate various network status (see BCR6). The LED2 pin polarity is programmable, but by default it is active LOW. When the LED2 pin polarity is programmed to active LOW, the output is an open drain driver. When the LED2 pin polarity is programmed to active HIGH, the output is a totem pole driver. LED3 LED3 Output This output is designed to directly drive an LED. By default, LED3 indicates transmit activity on the network. This pin can also be programmed to indicate other network status (see BCR7). The LED3 pin polarity is programmable, but by default it is active LOW. When the LED3 pin polarity is programmed to active LOW, the output is an open drain driver. When the LED3 pin po- Note: The LED3 pin is multiplexed with the EEDO pin. LED4 LED4 Output This output is designed to directly drive an LED. This pin can be programmed to indicate various network status (see BCR48). The LED4 pin polarity is programmable, but by default it is active LOW. When the LED4 pin polarity is programmed to active LOW, the output is an open drain driver. When the LED4 pin polarity is programmed to active HIGH, the output is a totem pole driver. EEPROM Interface EECS EEPROM Chip Select Output This pin is designed to directly interface to a serial EEPROM that uses the 93C46 EEPROM interface protocol. EECS is connected to the EEPROM's chip select pin. It is controlled by either the Am79C978 controller during command portions of a read of the entire EEPROM, or indirectly by the host system by writing to BCR19, bit 2. EEDI EEPROM Data In Output This pin is designed to directly interface to a serial EEPROM that uses the 93C46 EEPROM interface protocol. EEDI is connected to the EEPROM's data input pin. It is controlled by either the Am79C978 controller during command portions of a read of the entire EEPROM, or indirectly by the host system by writing to BCR19, bit 0. Note: The EEDI pin is multiplexed with the LED0 pin. EEDO EEPROM Data Out Input This pin is designed to directly interface to a serial EEPROM that uses the 93C46 EEPROM interface protocol. EEDO is connected to the EEPROM's data output pin. It is controlled by either the Am79C978 Am79C978 29 controller during command portions of a read of the entire EEPROM, or indirectly by the host system by reading from BCR19, bit 0. Note: The EEDO pin is multiplexed with the LED3 pin. EESK EEPROM Serial Clock Output This pin is designed to directly interface to a serial EEPROM that uses the 93C46 EEPROM interface protocol. EESK is connected to the EEPROM's clock pin. It is controlled by either the Am79C978 controller directly during a read of the entire EEPROM, or indirectly by the host system by writing to BCR19, bit 1. Note: The EESK pin is multiplexed with the LED1 pin. The EESK pin is also used during EEPROM AutoDetection to determine whether or not an EEPROM is present at the Am79C978 controller interface. At the rising edge of the last CLK edge while RST is asserted, EESK is sampled to determine the value of the EEDET bit in BCR19. A sampled HIGH value means that an EEPROM is present, and EEDET will be set to 1. A sampled LOW value means that an EEPROM is not present, and EEDET will be set to 0. See the EEPROM Auto-Detection section for more details. If no LED circuit is to be attached to this pin, then a pullup or pull-down resistor must be attached instead to resolve the EEDET setting. WARNING: The input signal level of EESK must be valid for correct EEPROM detection before the deassertion of RST. MII Interface RX_CLK Receive Clock Input RX_CLK is a clock input that provides the timing reference for the transfer of the RX_DV, RXD[3:0], and RX_ER signals into the Am79C978 device. RX_CLK must provide a nibble rate clock (25% of the network data rate). Hence, when the Am79C978 device is operating at 10 Mbps, it provides an RX_CLK frequency of 2.5 MHz, and at 100 Mbps it provides an RX_CLK frequency of 25 MHz. RXD[3:0] Receive Data Input RXD[3:0] is the nibble-wide MII-compatible receive data bus. Data on RXD[3:0] is sampled on every rising edge of RX_CLK while RX_DV is asserted. RXD[3:0] is ignored while RX_DV is de-asserted. RX_DV Receive Data Valid Input RX_CLK is synchronous to the receive data. In order for a frame to be fully received by the Am79C978 device, RX_DV must be asserted prior to the RX_CLK rising edge, when the first nibble of the Start of Frame Delimiter is driven on RXD[3:0], and must remain asserted until after the rising edge of RX_CLK, when the last nibble of the CRC is driven on RXD[3:0]. RX_DV must then be deasserted prior to the RX_CLK rising edge which follows this final nibble. RX_DV transitions are synchronous to RX_CLK rising edges. CRS Receive Carrier Sense CRS is an input that indicates that a non-idle medium, due either to transmit or receive activity, has been detected. COL Collision Input COL is an input that indicates that a collision has been detected on the network medium. RX_ER Receive Error Input RX_ER is an input that indicates that the MII transceiver device has detected a coding error in the receive data frame currently being transferred on the RXD[3:0] pins. If RX_ER is asserted while RX_DV is asserted, a CRC error will be indicated in the receive descriptor for the incoming receive frame. RX_ER is ignored while RX_DV is deasserted. Special code groups generated on RXD while RX_DV is deasserted are ignored (e.g., bad SSD in TX and idle in T4). RX_ER transitions are synchronous to RX_CLK. TX_CLK Transmit Clock Input TX_CLK is a clock input that provides the timing reference for the transfer of the TXD[3:0] and TX_ER signals into the Am79C978 device. TX_CLK must provide a nibble rate clock (25% of the network data rate). Hence, when the Am79C978 device is operating at 10 Mbps, it provides an TX_CLK frequency of 2.5 MHz, and at 100 Mbps it provides an RX_CLK frequency of 25 MHz. TXD[3:0] Transmit Data Output TXD[3:0] is the nibble-wide MII-compatible transmit data bus. Valid data is generated on TXD[3:0] on every rising edge of TX_CLK while TX_EN is asserted. While TX_EN is deasserted, TXD[3:0] values are driven to 0. TXD[3:0] transitions are synchronous to rising edges of TX_CLK. RX_DV is an input used to indicate that valid received data is being presented on the RXD[3:0] pins and 30 Input Am79C978 TX_EN Transmit Enable TDO Output Test Data Out Output TX_EN indicates when the Am79C978 device is presenting valid transmit nibbles on the MII TXD[3:0] bus. While TX_EN is asserted, the Am79C978 device generates TXD[3:0] and TX_ER on TX_CLK rising edges. TX_EN is asserted with the first nibble of preamble and remains asserted throughout the duration of the packet until it is deasserted prior to the first TX_CLK following the final nibble of the frame. TX_EN transitions are synchronous to TX_CLK. TDO is the test data output path from the Am79C978 controller. The pin is tri-stated when the JTAG port is inactive. MDC Ethernet Network Interfaces TX Management Data Clock Output MDC is the non-continuous clock output that provides a timing reference for bits on the MDIO pin. During MII management port operations, MDC runs at a nominal frequency of 2.5 MHz. When no management operations are in progress, MDC is driven LOW. If the MII port is not selected, the MDC pin may be left floating. MDIO Management Data Input/Output Output Input/ MDIO is a bidirectional MII management port data pin. MDIO is an output during the header portion of the management frame transfers and during the data portion of write operations. MDIO is an input during the data portion of read operations. If a PHY is attached to the MII port via a MII physical connector then the MDIO pin should be externally pulled down to Vss with a 10 k 5% resistor. If a PHY is directly attached to the MII pins then the MDIO pin should be externally pulled up to Vcc with a 10 k 5% resistor. IEEE 1149.1 (1990) Test Access Port Interface TCK Test Clock TMS Test Mode Select Input A serial input bit stream on the TMS pin is used to define the specific boundary scan test to be executed. The pin has an internal pull-up resistor. Serial Transmit Data Output These pins carry the transmit output data and are connected to the transmit side of the magnetics module. RX Serial Receive Data Input These pins accept the receive input data from the magnetics module. IREF Internal Current Reference Input This pin serves as a current reference for the integrated 1/10 PHY. It must be connected to VSS through a 12100- resistor (1%). PHY_RST PHY Reset Output This output is used to reset the external PHY. This output eliminates the need for a fanout buffer on the PCI reset (RST) signal, provided polarity control for the specific PHY used, and prevents the resetting of the PHY when the PG input is LOW. The output polarity is determined by the RST_POL (CRS116, bit0). HomePNA PHY Network Interface HRTXRXP/HRTXRXN Input Serial Receive Data Input/Output TCK is the clock input for the boundary scan test mode operation. It can operate at a frequency of up to 10 MHz. TCK has an internal pull-up resistor. These pins accept the receive input data from the magnetics module and carry the transmit output data. A 102- resistor should be placed between these pins. TDI Clock Interface XCLK/XTAL Test Data In Input TDI is the test data input path to the Am79C978 controller. The pin has an internal pull-up resistor. External Clock/Crystal Select Input When HIGH, an external 60-MHz clock source is selected bypassing the crystal circuit and clock trippler. When LOW, a 20-MHz crystal is used instead. The following table illustrates how this pin works. Am79C978 31 DVDDD Table 2. External Clock/Crystal Select 10BASE-T PDX Block Power Input Pin Output Pin XCLK/XTAL Clock Source XTAL1 XTAL2 0 20-MHz Crystal XTAL1 Don't Care 1 60-MHz Oscillator/ External CLK Source Crystal Oscillator In Input The internal clock generator utilizes either a 20-MHz crystal that is attached to pins XTAL1 and XTAL2 or a 60-MHz clock source connected to XTAL1. This pin is not 5 V tolerant, and the 60 MHz clock source must be from a 3.3 V source. XTAL2 Crystal Oscillator Out This pin supplies power to the 10 Mbps Transceiver block. It must be connected to a +3.3 V 300 mV source. This pin requires careful decoupling to ensure proper device performance. DVDDRX, DVDDTX 10BASE-T I/O Buffer Power XTAL1 Output The internal clock generator utilizesd a 20-MHz crystal that is attached to pins XTAL1 and XTAL2. +3.3 V Power +3.3 V Power These pins supply power to the 10BASE-T input/output buffers. They must be connected to a +3.3 V 300 mV source. These pins require careful decoupling to ensure proper device performance. DVDDA Analog PLL Power +3.3 V Power This pin supplies power to the IREF current reference circuit and the 10BASE-T analog PLL. They must be connected to a +3.3 V 300 mV source. These pins require careful decoupling to ensure proper device performance. Power Supply VDDB DVSSX, DVSSA I/O Buffer Power (5 Pins) These pins are the ground connection for the analog section within the Physical Data Transceiver (PDX) block. 10BASE-T PDX Analog Ground +3.3 V Power These pins are the power supply pins that are used by the input/output buffer drivers. All VDDB pins must be connected to a +3.3 V supply. VDD_PCI PCI I/O Buffer Power (9 Pins) +3.3 V Power Ground These pins are the ground pins that are used by the input/output buffer drivers. VDD +3.3 V Power These pins are the power supply pins that are used by the internal digital circuitry. All VDD pins must be connected to a +3.3 V supply. VSS Digital Ground (7 Pins) Ground There are seven ground pins that are used by the internal digital circuitry. 32 Ground This pin is the ground connection for the digital logic within the PDX block. VDDCO Crystal +3.3 V Power This pin supplies power to the crystal circuit. VSSB Digital Power (7 Pins) DVSSD 10BASE-T PDX Digital Ground These pins are the power supply pins that are used by the PCI input/output buffer drivers (except PME driver). All VDD_PCI pins must be connected to a +3.3 V supply. I/O Buffer Ground (15 Pins) Ground VDDHR HomePNA Digital Power +3.3 V Power These pins are the digital power supply pins that are used by the internal digital circuitry for the HomePNA block. They must be connected to a +3.3 V source. VSSHR HomePNA Analog Ground Ground This pin is the ground connection for the analog section within the HomePNA block. DVDDA_HR HomePNA Analog Power +3.3 V Power This pin supplies power to the analog section of the HomePNA block. It must be connected to a +3.3 V 300 mV source. This pin requires careful decoupling to ensure proper device performance. Am79C978 BASIC FUNCTIONS System Bus Interface The Am79C978 controller is designed to operate as a bus master during normal operations. Some slave I/O accesses to the Am79C978 controller are required in normal operations as well. Initialization of the Am79C978 controller is achieved through a combination of PCI Configuration Space accesses, bus slave accesses, bus master accesses, and an optional read of a serial EEPROM that is performed by the Am79C978 controller. The EEPROM read operation is performed through the 93C46 EEPROM interface. The ISO 8802-3 (IEEE/ANSI 802.3) Ethernet Address may reside within the serial EEPROM. Some controller configuration registers may also be programmed by the EEPROM read operation. The Address PROM, on-chip board-configuration registers, and the Ethernet controller registers occupy 32 bytes of address space. I/O and memory mapped I/O accesses are supported. Base Address registers in the PCI configuration space allow locating the address space on a wide variety of starting addresses. Software Interface The software interface to the Am79C978 controller is divided into three parts. One part is the PCI configuration registers used to identify the Am79C978 controller and to setup the configuration of the device. The setup information includes the I/O or memory mapped I/O base address, mapping of the Expansion ROM, and the routing of the Am79C978 controller interrupt channel. This allows for a jumperless implementation. The second portion of the software interface is the direct access to the I/O resources of the Am79C978 controller. The Am79C978 controller occupies 32 bytes of address space that must begin on a 32-byte block boundary. The address space can be mapped into I/O or memory space (memory mapped I/O). The I/O Base Address Register in the PCI Configuration Space controls the start address of the address space if it is mapped to I/O space. The Memory Mapped I/O Base Address Register controls the start address of the address space if it is mapped to memory space. The 32byte address space is used by the software to program the Am79C978 controller operating mode, to enable and disable various features, to monitor operating status, and to request particular functions to be executed by the Am79C978 controller. The third portion of the software interface is the descriptor and buffer areas that are shared between the software and the Am79C978 controller during normal network operations. The descriptor area boundaries are set by the software and do not change during nor- mal network operations. There is one descriptor area for receive activity, and there is a separate area for transmit activity. The descriptor space contains relocatable pointers to the network frame data, and it is used to transfer frame status from the Am79C978 controller to the software. The buffer areas are locations that hold frame data for transmission or that accept frame data that has been received. Network Interfaces The Am79C978 controller provides all of the PHY layer functions for 10 Mbps (10BASE-T) or 1 Mbps. The Am79C978 controller supports both half-duplex and full-duplex operation on the network MII interface. Media Independent Interface The Am79C978 controller fully supports the MII according to the IEEE 802.3u standard. This Reconciliation Sublayer interface allows a variety of PHYs (100BASE-TX, 100BASE-FX, 100BASE-T4, 100BASE-T2, 10BASE-T, etc.) to be attached to the Am79C978 device without future upgrade problems. The MII interface is a 4-bit (nibble) wide data path interface that runs at 25 MHz for 100-Mbps networks or 2.5 MHz for 10-Mbps networks. The interface consists of two independent data paths, receive (RXD(3:0)) and transmit (TXD(3:0)), control signals for each data path (RX_ER, RX_DV, TX_EN), network status signals (COL, CRS), clocks (RX_CLK, TX_CLK) for each data path, and a two-wire management interface (MDC and MDIO). See Figure 2. MII Transmit Interface The MII transmit clock is generated by the external PHY and is sent to the Am79C978 controller on the TX_CLK input pin. The clock can run at 25 MHz or 2.5 MHz, depending on the speed of the network to which the external PHY is attached. The data is a nibble-wide (4 bits) data path, TXD(3:0), from the Am79C978 controller to the external PHY and is synchronous to the rising edge of TX_CLK. The transmit process starts when the Am79C978 controller asserts the TX_EN, which indicates to the external PHY that the data on TXD(3:0) is valid. Normally, unrecoverable errors are signaled through the MII to the external PHY with the TX_ER output pin. The external PHY will respond to this error by generating a TX coding error on the current transmitted frame. The Am79C978 controller does not use this method of signaling errors on the transmit side. The Am79C978 controller will invert the FCS on the last byte generating an invalid FCS. The TX_ER pin should be tied to GND. Am79C978 33 4 RXD(3:0) RX_DV Receive Signals RX_ER Am79C978 MII Interface RX_CLK CRS COL Network Status Signals 4 TXD(3:0) TX_EN Transmit Signals TX_CLK MDC Management Port Signals MDIO 22206B-4 Figure 1. Media Independent Interface MII Receive Interface MII Network Status Interface The MII receive clock is also generated by the external PHY and is sent to the Am79C978 controller on the RX_CLK input pin. The clock will be the same frequency as the TX_CLK but will be out of phase and can run at 25 MHz or 2.5 MHz, depending on the speed of the network to which the external PHY is attached. The MII also provides signals that are consistent and necessary for IEEE 802.3 and IEEE 802.3u operation. These signals are CRS (Carrier Sense) and COL (Collision Sense). Carrier Sense is used to detect non-idle activity on the network. Collision Sense is used to indicate that simultaneous transmission has occurred in a half-duplex network. The RX_CLK is a continuous clock during the reception of the frame, but can be stopped for up to two RX_CLK periods at the beginning and the end of frames, so that the external PHY can sync up to the network data traffic necessary to recover the receive clock. During this time, the external PHY may switch to the TX_CLK to maintain a stable clock on the receive interface. The Am79C978 controller will handle this situation with no loss of data. The data is a nibble-wide (4 bits) data path, RXD(3:0), from the external PHY to the Am79C978 controller and is synchronous to the rising edge of RX_CLK. The receive process starts when RX_DV is asserted. RX_DV will remain asserted until the end of the receive frame. The Am79C978 controller requires CRS (Carrier Sense) to toggle in between frames in order to receive them properly. Errors in the currently received frame are signaled across the MII by the RX_ER pin. RX_ER can be used to signal special conditions out of band when RX_DV is not asserted. Two defined out-ofband conditions for this are the 100BASE-TX signaling of bad Start of Frame Delimiter and the 100BASE-T4 indication of illegal code group before the receiver has synched to the incoming data. The Am79C978 controller will not respond to these conditions. All out of band conditions are currently treated as NULL events. 34 MII Management Interface The MII provides a two-wire management interface so that the Am79C978 controller can control and receive status from external PHY devices. The Network Port Manager copies the PHYAD after the Am79C978 controller reads the EEPROM and uses it to communicate with the external PHY. (Refer also to the BCR49 description). The PHY address must be programmed into the EEPROM prior to starting the Am79C978 controller. This is necessary so that the internal management controller can work autonomously from the software driver and can always know where to access the external PHY. The Am79C978 controller is unique by offering direct hardware support of the external PHY device without software support. The PHY address of 1Fh is reserved and should not be used. To access the internal or external PHYs, the software driver must have knowledge of the PHY's address before attempting to address it. The MII Management Interface uses the MII Control, Address, and Data registers (BCR32, 33, 34) to control an d c om mu ni c at e to th e e x te r na l PH Y s. Th e Am79C978 controller generates MII management frames to the external PHY through the MDIO pin synchronous to the rising edge of the Management Data Clock (MDC) based on a combination of writes and reads to these registers. Am79C978 MII Management Frames MII management frames are automatically generated by the Am79C978 controller and conform to the MII clause in the IEEE 802.3u standard. The start of the frame may be a preamble of 32 ones (unless bit 6 of register equals 1) and guarantees that all of the external PHYs are synchronized on the same interface. See Figure 2. Loss of synchronization is pos- Preamble 1111....1111 32 Bits sible due to the hot-plugging capability of the exposed MII. The IEEE 802.3 specification allows you to drop the preamble, if after reading the MII Status Register from the external PHY you can determine that the external PHY will support Preamble Suppression (BCR34, bit 6). After having a valid MII Status Register read, the Am79C978 controller will then drop the creation of the preamble stream until a reset occurs, receives a read error, or the external PHY is disconnected. ST 01 OP 10 Rd 01 Wr PHY Address Register Address TA Z0 Rd 10 Wr Data Idle Z 2 Bits 2 Bits 5 Bits 5 Bits 2 Bits 16 Bits 1 Bit 22206B-5 Figure 2. Frame Format at the MII Interface Connection This is followed by a start field (ST) and an operation field (OP). The operation field (OP) indicates whether the Am79C978 controller is initiating a read or write operation. This is followed by the external PHY address (PHYAD) and the register address (REGAD) programmed in BCR33. The PHY address of 1D,1E, and 1F are reserved and should not be used. The external PHY may have a larger address space starting at 10h - 1Fh. This is the address range set aside by the IEEE as vendor usable address space and will vary from vendor to vendor. This field is followed by a bus turnaround field. During a read operation, the bus turnaround field is used to determine if the external PHY is responding correctly to the read request or not. The Am79C978 controller will tri-state the MDIO for both MDC cycles. During the second cycle, if the external PHY is synchronized to the Am79C978 controller, the external PHY will drive a 0. If the external PHY does not drive a 0, the Am79C978 controller will signal a MREINT (CSR7, bit 9) interrupt, if MREINTE (CSR7, bit 8) is set to a 1, indicating the Am79C978 controller had an MII management frame read error and that the data in BCR34 is not valid. The data field to/from the external PHY is read or written into the BCR34 register. The last field is an IDLE field that is necessary to give ample time for drivers to turn off before the next access. The Am79C978 controller will drive the MDC to 0 and tristate the MDIO anytime the MII Management Port is not active. To help to speed up the reading and of writing the MII management frames to the external PHY, the MDC can be sped up to 5 MHz by setting the FMDC bits in BCR32. The IEEE 802.3 specification requires use of the 2.5-MHz clock rate, but 5 MHz is also available for the user. The 5-MHz clock rate can be used for an exposed MII with one external PHY attached. The 2.5MHz clock rate is intended to be used when multiple external PHYs are connected to the MII Management Port or if compliance to the IEEE 802.3u standard is required. Auto-Poll External PHY Status Polling As defined in the IEEE 802.3 standard, the external PHY attached to the Am79C978 controller's MII has no way of communicating important timely status information back to Am79C978 controller. The Am79C978 controller has no way of knowing that an external PHY has undergone a change in status without polling the MII status register. To prevent problems from occurring with i nadequate host or software polling, the Am79C978 controller will Auto-Poll when APEP (BCR32, bit 11) is set to 1 to insure that the most current information is available. See 10BASE-T PHY Management Registers for the bit descriptions of the MII Status Register. The contents of the latest read from the external PHY will be stored in a shadow register in the Auto-Poll block. The first read of the MII Status Register will just be stored, but subsequent reads will be compared to the contents already stored in the shadow register. If there has been a change in the contents of the MII Status Register, a MAPINT (CSR7, bit 5) interrupt will be generated on INTA if the MAPINTE (CSR7, bit 4) is set to 1. The Auto-Poll features can be disabled if software driver polling is required. Am79C978 35 The Auto-Poll's frequency of generating MII management frames can be adjusted by setting of the APDW bits (BCR32, bits 10-8). The delay can be adjusted from 0 MDC periods to 2048 MDC periods. Auto-Poll by default will only read the MII Status register of the currently active PHY. Network Port Manager If the PHY is active, the Network Port Manager will request status from the selected PHY by generating MII management frames. These frames will be sent roughly every 900 ms. These frames are necessary so that the Network Port Manager can monitor the current active link and can notify the software if the current link goes down. Slave Bus Interface Unit The slave Bus Interface Unit (BIU) controls all accesses to the PCI configuration space, the Control and Status Registers (CSR), the Bus Configuration Registers (BCR), and the Address PROM (APROM) locations. Table 5 shows the response of the Am79C978 controller to each of the PCI commands in slave mode. Table 5. Slave Commands C[3:0] 10BASE-T PHY The 10BASE-T transceiver incorporates the physical layer function, including both clock recovery (ENDEC) and transceiver function. Data transmission over the 10BASE-T medium requires an integrated 10BASE-T MAU. The transceiver will meet the electrical requirements for 10BASE-T as specified in IEEE 802.3i. The transmit signal is filtered on the transceiver to reduce harmonic content per IEEE 802.3i. Since filtering is performed in silicon, external filtering modules are not needed. The 10BASE-T PHY transceiver receives 10 Mbps data from the MAC across the internal MII at 2.5 million nibbles per second (parallel), or 10 million bits per second (serial) for 10BASE-T. It then Manchester encodes the data before transmission to the network. The RX+ pins are differential twisted-pair receivers. When properly terminated, each receiver will meet the electrical requirements for 10BASE-T as specified in IEEE 802.3i. Each receiver has internal filtering and does not r equir e external fil ter modules. The 10BASE-T PHY transceiver receives a Manchester coded 10BASE-T data stream from the medium. It then recovers the clock and decodes the data. The data stream is presented at the internal MII interface in parallel format. Table 3. PCI Device ID Vendor ID Device ID Rev ID (offset 0x08) 1022 2001 51 Table 4. PCI Software Configuration 36 CSR89 CSR88 JTAG 00001262h 00006003h 1262 6003h Use 0000 Interrupt Acknowledge Not used 0001 Special Cycle Not used 0010 I/O Read Read of CSR, BCR, APROM, and Reset registers 0011 I/O Write Write to CSR, BCR, and APROM 0100 Reserved 0101 Reserved 0110 Memory Read Memory mapped I/O read of CSR, BCR, APROM, and Reset registers. Read of the Expansion Bus 0111 Memory Write Memory mapped I/O write of CSR, BCR, and APROM 1000 Reserved 1001 Reserved 1010 Configuration Read Read of the Configuration Space 1011 Configuration Write Write to the Configuration Space 1100 Memory Read Multiple Aliased to Memory Read 1101 Dual Address Cycle Not used 1110 Memory Read Line Aliased to Memory Read 1111 Memory Write Invalidate Aliased to Memory Write PCI and JTAG Configuration Information The PCI device ID and software configuration information is as follows in Table 3 and Table 4. Command Slave Configuration Transfers The host can access the PCI configuration space with a c on f i g u r a t i o n r e a d o r w r i t e c o m m a n d . T h e Am79C978 controller will assert DEVSEL during the address phase when IDSEL is asserted, AD[1:0] are both 0, and the access is a configuration cycle. AD[7:2] select the DWord location in the configuration space. The Am79C978 controller ignores AD[10:8], because it Am79C978 is a single function device. AD[31:11] are "don't cares." See Table 6. Table 6. Slave Configuration Transfers AD31 AD11 AD10 AD8 AD7 AD2 Don't care Don't care DWord Index AD1 AD0 0 0 The active bytes within a DWord are determined by the byte enable signals. Eight-bit, 16-bit, and 32-bit transfers are supported. DEVSEL is asserted two clock cyc le s a fte r t he ho s t ha s as s e r te d F RA ME. A ll c onf ig ur at io n c y cl es a re of fi xe d l en gth . Th e Am79C978 controller will assert TRDY on the third clock of the data phase. The Am79C978 controller does not support burst transfers for access to configuration space. When the host keeps FRAME asserted for a second data phase, the Am79C978 controller will disconnect the transfer. When the host tries to access the PCI configuration space while the automatic read of the EEPROM after H_RESET (see section on RESET) is on-going, the Am79C978 controller will terminate the access on the PCI bus with a disconnect/retry response. The Am79C978 controller supports fast back-to-back transactions to different targets. This is indicated by the Fast Back-To-Back Capable bit (PCI Status register, bit 7), which is hardwired to 1. The Am79C978 controller is capable of detecting a configuration cycle even when its address phase immediately follows the data phase of a transaction to a different target without any idle state in-between. There will be no contention on the DEVSEL, TRDY, and STOP signals, since the Am79C978 controller asserts DEVSEL on the second clock after FRAME is asserted (medium timing). Slave I/O Transfers After the Am79C978 controller is configured as an I/O device by setting IOEN (for regular I/O mode) or MEMEN (for memory mapped I/O mode) in the PCI Command register, it starts monitoring the PCI bus for access to its CSR, BCR, or EEPROM locations. If configured for regular I/O mode, the Am79C978 controller will look for an address that falls within its 32 bytes of I/ O address space (starting from the I/O base address). The Am79C978 controller asserts DEVSEL if it detects an address match and the access is an I/O cycle. If configured for memory mapped I/O mode, the Am79C978 controller will look for an address that falls within its 32 bytes of memory address space (starting from the memory mapped I/O base address). The Am79C978 controller asserts DEVSEL if it detects an address match and the access is a memory cycle. DEVSEL is asserted two clock cycles after the host has asserted FRAME. See Figure 3 and Figure 4. The Am79C978 controller will not assert DEVSEL if it detects an address match and the PCI command is not of the correct type. In memory mapped I/O mode, the Am79C978 controller aliases all accesses to the I/O resources of the command types Memory Read Multiple and Memory Read Line to the basic Memory Read command. All accesses of the type Memory Write and Invalidate are aliased to the basic Memory Write command. Eight-bit, 16-bit, and 32-bit non-burst transactions are supported. The Am79C978 controller decodes all 32 address lines to determine which I/O resource is accessed. The typical number of wait states added to a slave I/O or memory mapped I/O read or write access on the part of the Am79C978 controller is six to seven clock cycles, depending upon the relative phases of the internal Buffer Management Unit clock and the CLK signal, since the internal Buffer Management Unit clock is a divideby-two version of the CLK signal. The Am79C978 controller does not support burst transfers for access to its I/O resources. When the host keeps FRAME asserted for a second data phase, the Am79C978 controller will disconnect the transfer. The Am79C978 controller supports fast back-to-back transactions to different targets. This is indicated by the Fast Back-To-Back Capable bit (PCI Status register, bit 7), which is hardwired to 1. The Am79C978 controller is capable of detecting an I/O or a memory-mapped I/ O cycle even when its address phase immediately follows the data phase of a transaction to a different target, without any idle state in-between. There will be no contention on the DEVSEL, TRDY, and STOP signals, since the Am79C978 controller asserts DEVSEL on the second clock after FRAME is asserted (medium timing). See Figure 5 and Figure 6. Am79C978 37 CLK CLK 1 2 3 4 5 7 6 1 FRAME 3 4 5 6 FRAME AD ADDR C/BE 1010 PAR 2 DATA AD ADDR C/BE 1011 BE PAR DATA BE PAR PAR PAR PAR IRDY IRDY TRDY TRDY DEVSEL DEVSEL STOP STOP IDSEL IDSEL DEVSEL is sampled 22206B-6 22206B-7 Figure 3. Slave Configuration Read Figure 4. Slave Configuration Write CLK 1 2 3 4 5 6 7 8 9 10 11 FRAME AD ADDR C/BE 0010 PAR DATA BE PAR PAR IRDY TRDY DEVSEL STOP 22206B-8 Figure 5. 38 Slave Read Using I/O Command Am79C978 7 CLK 1 2 3 4 5 6 7 8 9 10 11 FRAME AD ADDR DATA C/BE 0111 BE PAR PAR PAR IRDY TRDY DEVSEL STOP 22206B-9 Figure 6. Slave Write Using Memory Command Expansion ROM Transfers pansion ROM is present when it reads the ROM signature 55H (byte 0) and AAH (byte 1). Since the Am79C978 device does not have expansion ROM capabilities, PCI configuration offset must be set to 30H = 0. Slave Cycle Termination There are three scenarios besides normal completion of a transaction where the Am79C978 controller is the target of a slave cycle and it will terminate the access. During the boot procedure, the system will try to find an Expansion ROM. A PCI system assumes that an Ex- CLK 1 2 3 4 5 48 49 50 51 FRAME AD ADDR C/BE CMD PAR DATA BE PAR PAR IRDY TRDY DEVSEL STOP 22206B-10 DEVSEL is sampled Figure 7. Expansion ROM Read Am79C978 39 Disconnect When Busy The Am79C978 controller cannot service any slave access while it is reading the contents of the EEPROM. Simultaneous access is not allowed in order to avoid conflicts, since the EEPROM is used to initialize some of the PCI configuration space locations and most of the BCRs and CSR116. The EEPROM read operation will always happen automatically after the deassertion of the RST pin. In addition, the host can start the read operation by setting the PREAD bit (BCR19, bit 14). While the EEPROM read is on-going, the Am79C978 controller will disconnect any slave access where it is the target by asserting STOP together with DEVSEL, while driving TRDY high. STOP will stay asserted until the end of the cycle. CLK 1 2 3 4 5 FRAME AD ADDR DATA C/BE CMD BE PAR PAR PAR IRDY A second situation where the Am79C978 controller will generate a PCI disconnect/retry cycle is when the host tries to access any of the I/O resources right after having read the Reset register. Since the access generates an internal reset pulse of about 1 ms in length, all further slave accesses will be deferred until the internal reset operation is completed. See Figure 8. TRDY DEVSEL STOP Disconnect Of Burst Transfer The Am79C978 controller does not support burst access to the configuration space, the I/O resources, or to the Expansion Bus. The host indicates a burst transaction by keeping FRAME asserted during the data phase. When the Am79C978 controller sees FRAME and IRDY asserted in the clock cycle before it wants to assert TRDY, it also asserts STOP at the same time. The transfer of the first data phase is still successful, since IRDY and TRDY are both asserted. See Figure 9. 22206B-11 Figure 8. Disconnect of Slave Cycle When Busy CLK 1 2 3 4 5 FRAME If the host is not yet ready when the Am79C978 controller asserts TRDY, the device will wait for the host to assert IRDY. When the host asserts IRDY and FRAME is still asserted, the Am79C978 controller will finish the first data phase by deasserting TRDY one clock later. At the same time, it will assert STOP to signal a disconnect to the host. STOP will stay asserted until the host removes FRAME. See Figure 10. AD C/BE PAR 1st DATA BE DATA BE PAR PAR IRDY TRDY DEVSEL STOP 22206B-12 Figure 9. Disconnect of Slave Burst Transfer - No Host Wait States 40 Am79C978 CLK 1 2 3 4 5 CLK 6 1 2 3 4 5 FRAME FRAME AD C/BE PAR 1st DATA BE DATA AD ADDR 1st DATA C/BE CMD BE BE PAR PAR PAR PAR PAR IRDY SERR TRDY DEVSEL DEVSEL 22206B-14 STOP Figure 11. Address Parity Error Response 22206B-13 Figure 10. Disconnect of Slave Burst Transfer Host Inserts Wait States Parity Error Response When the Am79C978 controller is not the current bus master, it samples the AD[31:0], C/BE[3:0], and the PAR lines during the address phase of any PCI command for a parity error. When it detects an address parity error, the Am79C978 controller sets PERR (PCI Status register, bit 15) to 1. When reporting of that error is enabled by setting SERREN (PCI Command register, bit 8) and PERREN (PCI Command register, bit 6) to 1, the Am79C978 controller also drives the SERR signal low for one clock cycle and sets SERR (PCI Status register, bit 14) to 1. The assertion of SERR follows th e a d dr e s s p h a s e b y t w o c l o c k c y c l e s . T h e Am79C978 controller will not assert DEVSEL for a PCI transaction that has an address parity error when PERREN and SERREN are set to 1. See Figure 11. During the data phase of an I/O write, memory-mapped I/O write, or configuration write command that selects the Am79C978 controller as target, the device samples the AD[31:0] and C/BE[3:0] lines for parity on the clock edge, and data is transferred as indicated by the assertion of IRDY and TRDY. PAR is sampled in the following clock cycle. If a parity error is detected and reporting of that error is enabled by setting PERREN (PCI Command register, bit 6) to 1, PERR is asserted one clock later. The parity error will always set PERR (PCI Status register, bit 15) to 1 even when PERREN is cleared to 0. The Am79C978 controller will finish a transaction that has a data parity error in the normal way by asserting TRDY. The corrupted data will be written to the addressed location. Figure 12 shows a transaction that suffered a parity error at the time data was transferred (clock 7, IRDY and TRDY are both asserted). PERR is driven high at the beginning of the data phase and then drops low due to the parity error on clock 9, two clock cycles after the data was transferred. After PERR is driven low, the Am79C978 controller drives PERR high for one clock cycle, since PERR is a sustained tri-state signal. Am79C978 41 CLK 1 2 3 4 5 6 7 8 9 10 FRAME AD ADDR DATA C/BE CMD BE PAR PAR PAR PERR IRDY TRDY DEVSEL 22206B-15 Figure 12. Slave Cycle Data Parity Error Response Master Bus Interface Unit Table 7. The master Bus Interface Unit (BIU) controls the acquisition of the PCI bus and all accesses to the initialization block, descriptor rings, and the receive and transmit buffer memory. Table 7 shows the usage of PCI commands by the Am79C978 controller in master mode. Table 7. C[3:0] Master Commands Command Use 0000 Interrupt Acknowledge Not used 0001 Special Cycle Not used 0010 I/O Read Not used 0011 I/O Write Not used 0100 Reserved 0101 Reserved 1010 Configuration Read Not used 1011 Configuration Write Not used 1100 Memory Read Multiple Read of the transmit buffer in burst mode 1101 Dual Address Cycle Not used 1110 Memory Read Line Read of the transmit buffer in burst mode 1111 Memory Write Invalidate Not used Bus Acquisition 0110 Memory Read Read of the initialization block and descriptor rings Read of the transmit buffer in non-burst mode 0111 Memory Write Write to the descriptor rings and to the receive buffer 1000 Reserved 1001 Reserved 42 Master Commands (Continued) The microcode will determine when a DMA transfer should be initiated. The first step in any bus master transfer is to acquire ownership of the bus. This task is handled by synchronous logic within the BIU. Bus ownership is requested with the REQ signal and ownership is granted by the arbiter through the GNT signal. Figure 13 shows the Am79C978 controller bus acquisition. REQ is asserted and the arbiter returns GNT while ano ther bu s m ast er is tra ns fer ri ng d ata. Th e Am79C978 controller waits until the bus is idle (FRAME and IRDY deasserted) before it starts driving AD[31:0] and C/BE[3:0] on clock 5. FRAME is asserted at clock 5 indicating a valid address and command on AD[31:0] and C/BE[3:0]. The Am79C978 controller does not use address stepping which is reflected by Am79C978 ADSTEP (bit 7) in the PCI Command register being hardwired to 0. The Am79C978 controller typically performs more than one non-burst read transaction within a single bus mastership period. FRAME is dropped between consecutive non-burst read cycles. REQ stays asserted until FRAME is asserted for the last transaction. The Am79C978 controller supports zero wait state read cycles. It asserts IRDY immediately after the address phase and at the same time starts sampling DEVSEL. Figure 14 shows two non-burst read transactions. The first transaction has zero wait states. In the second transaction, the target extends the cycle by asserting TRDY one clock later. CLK 1 2 3 4 5 FRAME AD ADDR C/BE CMD Am79C978 controller will internally discard unneeded bytes. Basic Burst Read Transfer IRDY REQ GNT 22206B-16 Figure 13. Bus Acquisition In burst mode, the deassertion of REQ depends on the setting of EXTREQ (BCR18, bit 8). If EXTREQ is cleared to 0, REQ is deasserted at the same time as FRAME is asserted. (The Am79C978 controller never performs more than one burst transaction within a single bus mastership period.) If EXTREQ is set to 1, the Am79C978 controller does not deassert REQ until it starts the last data phase of the transaction. Once asserted, REQ remains active until GNT has become active and independent of subsequent setting of STOP (CSR0, bit 2) or SPND (CSR5, bit 0). The assertion of H_RESET or S_RESET, however, will cause REQ to go inactive immediately. Bus Master DMA Transfers There are four primary types of DMA transfers. The Am79C978 controller uses non-burst as well as burst cycles for read and write access to the main memory. Basic Non-Burst Read Transfer By default, the Am79C978 controller uses non-burst cycles in all bus master read operations. All controller non-burst read accesses are of the PCI command type Memory Read (type 6). Note that during a non-burst read operation, all byte lanes will always be active. The The Am79C978 controller supports burst mode for all bus master read operations. The burst mode must be enabled by setting BREADE (BCR18, bit 6). To allow burst transfers in descriptor read operations, the Am79C978 controller must also be programmed to use SWSTYLE 3 (BCR20, bits 7-0). All burst read accesses to the initialization block and descriptor ring are of the PCI command type Memory Read (type 6). Burst read accesses to the transmit buffer typically are longer than two data phases. When MEMCMD (BCR18, bit 9) is cleared to 0, all burst read accesses to the transmit buffer are of the PCI command type Memory Read Line (type 14). When MEMCMD (BCR18, bit 9) is set to 1, all burst read accesses to the transmit buffer are of the PCI command type Memory Read Multiple (type 12). AD[1:0] will both be 0 during the address phase indicating a linear burst order. Note that during a burst read operation, all byte lanes will always be active. The Am79C978 controller will internally discard unneeded bytes. The Am79C978 controller will always perform only a single burst read transaction per bus mastership period, where transaction is defined as one address ph as e a nd one or m ul ti pl e d ata ph as es . Th e Am79C978 controller supports zero wait state read cycles. It asserts IRDY immediately after the address phase and at the same time starts sampling DEVSEL. FRAME is deasserted when the next to last data phase is completed. Figure 15 shows a typical burst read access. The Am79C978 controller arbitrates for the bus, is granted access, reads three 32-bit words (DWord) from the system memory, and then releases the bus. In the example, the memory system extends the data phase of each access by one wait state. The example assumes that EXTREQ (BCR18, bit 8) is cleared to 0, therefore, REQ is deasserted in the same cycle as FRAME is asserted. Am79C978 43 CLK 1 2 3 4 5 6 7 8 9 11 10 FRAME DATA ADDR AD 0110 C/BE 0000 0110 0000 PAR PAR PAR DATA ADDR PAR PAR IRDY TRDY DEVSEL REQ GNT 22206B-17 DEVSEL is sampled Figure 14. Non-Burst Read Transfer CLK 1 2 3 4 5 6 7 8 9 10 11 FRAME AD C/BE DATA ADDR 1110 PAR DATA DATA 0000 PAR PAR PAR PAR IRDY TRDY DEVSEL REQ GNT 22206B-18 DEVSEL is sampled Figure 15. Burst Read Transfer (EXTREQ = 0, MEMCMD = 0) 44 Am79C978 Basic Non-Burst Write Transfer Basic Burst Write Transfer By default, the Am79C978 controller uses non-burst cycles in all bus master write operations. All controller non-burst write accesses are of the PCI command type Memory Write (type 7). The byte enable signals indicate the byte lanes that have valid data. The Am79C978 controller typically performs more than one non-burst write transaction within a single bus mastership period. FRAME is dropped between consecutive non-burst write cycles. REQ stays asserted until FRAME is asserted for the last transaction. The Am79C978 controller supports zero wait state write cycles except with descriptor write transfers. (See the section Descriptor DMA Transfers for the only exception.) It asserts IRDY immediately after the address phase. The Am79C978 controller supports burst mode for all bus master write operations. The burst mode must be enabled by setting BWRITE (BCR18, bit 5). To allow burst transfers in descriptor write operations, the Am79C978 controller must also be programmed to use SWSTYLE 3 (BCR20, bits 7-0). All controller burst write transfers are of the PCI command type Memory Write (type 7). AD[1:0] will both be 0 during the address phase indicating a linear burst order. The byte enable signals indicate the byte lanes that have valid data. The Am79C978 controller will always perform a single burst write transaction per bus mastership period, where transaction is defined as one address phase and one or multiple data phases. The Am79C978 controller supports zero wait state write cycles except with the case of descriptor write transfers. (See the section Descriptor DMA Transfers for the only exception.) The device asserts IRDY immediately after the address phase and at the same time starts sampling DEVSEL. FRAME is deasserted when the next to last data phase is completed. Figure 16 shows two non-burst write transactions. The first transaction has two wait states. The target inserts one wait state by asserting DEVSEL one clock late and another wait state by also asserting TRDY one clock late. The second transaction shows a zero wait state write cycle. The target asserts DEVSEL and TRDY in the same cycle as the Am79C978 controller asserts IRDY. CLK 1 2 3 4 5 6 7 8 9 10 FRAME AD C/BE ADDR DATA ADDR DATA 0111 BE 0111 BE PAR PAR PAR PAR PAR IRDY TRDY DEVSEL REQ GNT 22206B-19 DEVSEL is sampled Figure 16. Non-Burst Write Transfer Figure 17 shows a typical burst write access. The Am79C978 controller arbitrates for the bus, is granted access, and writes four 32-bit words (DWords) to the system memory and then releases the bus. In this ex- Am79C978 45 ample, the memory system extends the data phase of the first access by one wait state. The following three data phases take one clock cycle each, which is determined by the timing of TRDY. The example assumes that EXTREQ (BCR18, bit 8) is set to 1, therefore, REQ is not deasserted until the next to last data phase is finished. Disconnect With Data Transfer Figure 18 shows a disconnection in which one last data transfer occurs after the target asserted STOP. STOP is asserted on clock 4 to start the termination sequence. Data is still transferred during this cycle, since both IRDY and TRDY are asserted. The Am79C978 controller terminates the current transfer with the deassertion of FRAME on clock 5 and of IRDY one clock later. It finally releases the bus on clock 7. If it wants to transfer more data, the Am79C978 controller will again request the bus after two clock cycles. The starting address of the new transfer will be the address of the next non-transferred data. Target Initiated Termination When the Am79C978 controller is a bus master, the cycles it produces on the PCI bus may be terminated by the target in one of three different ways: disconnect with data transfer, disconnect without data transfer, and target abort. CLK 1 2 3 4 5 6 7 8 DATA DATA DATA PAR PAR 9 FRAME AD C/BE ADDR DATA 0111 BE PAR PAR PAR PAR IRDY TRDY DEVSEL REQ GNT 22206B-20 DEVSEL is sampled Figure 17. Burst Write Transfer (EXTREQ = 1) 46 Am79C978 CLK 1 2 3 4 5 DATA DATA 6 7 8 9 10 11 FRAME ADDRi AD 0111 C/BE 0000 PAR PAR ADDRi+8 0111 PAR IRDY TRDY DEVSEL STOP REQ GNT 22206B-21 DEVSEL is sampled Figure 18. Disconnect With Data Transfer Disconnect Without Data Transfer Figure 19 shows a target disconnect sequence during which no data is transferred. STOP is asserted on clock 4 without TRDY being asserted at the same time. The Am79C978 controller terminates the access with the deassertion of FRAME on clock 5 and of IRDY one clock cycle later. It finally releases the bus on clock 7. The Am79C978 controller will again request the bus after two clock cycles to retry the last transfer. The starting address of the new transfer will be the address of the last non-transferred data. Target Abort Figure 20 shows a target abort sequence. The target asserts DEVSEL for one clock. It then deasserts DEVSEL and asserts STOP on clock 4. A target can use the target abort sequence to indicate that it cannot service the data transfer and that it does not want the transaction to be retried. Additionally, the Am79C978 controller cannot make any assumption about the success of the previous data transfers in the current transaction. The Am79C978 controller terminates the current transfer with the deassertion of FRAME on clock 5 and of IRDY one clock cycle later. It finally releases the bus on clock 6. Since data integrity is not guaranteed, the Am79C978 controller cannot recover from a target abort event. TheAm79C978 controller will reset all CSR locations to their STOP_RESET values. The BCR and PCI configuration registers will not be cleared. Any on-going network transmission is terminated in an orderly sequence. If less than 512 bits have been transmitted onto the network, the transmission will be terminated immediately, generating a runt packet. If 512 bits or more have been transmitted, the message will have the current FCS inverted and appended at the next byte boundary to guarantee an FCS error is detected at the receiving station. Am79C978 47 CLK 1 2 3 4 5 6 7 8 9 10 11 FRAME AD C/BE ADDRi DATA ADDRi 0111 0000 0111 PAR PAR PAR IRDY TRDY DEVSEL STOP REQ GNT 22206B-22 DEVSEL is sampled Figure 19. Disconnect Without Data Transfer RTABORT (PCI Status register, bit 12) will be set to indicate that the Am79C978 controller has received a target abort. In addition, SINT (CSR5, bit 11) will be set to 1. When SINT is set, INTA is asserted if the enable bit SINTE (CSR5, bit 10) is set to 1. This mechanism can be used to inform the driver of the system error. The host can read the PCI Status register to determine the exact cause of the interrupt. Master Initiated Termination There are three scenarios besides normal completion of a transaction where the Am79C978 controller will terminate the cycles it produces on the PCI bus. Preemption During Non-Burst Transaction When the Am79C978 controller performs multiple nonburst transactions, it keeps REQ asserted until the assertion of FRAME for the last transaction. When GNT is removed, the Am79C978 controller will finish the current transaction and then release the bus. If it is not the 48 last transaction, REQ will remain asserted to regain bus ownership as soon as possible. See Figure 21. Preemption During Burst Transaction When the Am79C978 controller operates in burst mode, it only performs a single transaction per bus mastership period, where transaction is defined as one address phase and one or multiple data phases. The central arbiter can remove GNT at any time during the transaction. TheAm79C978 controller will ignore the deassertion of GNT and continue with data transfers, as long as the PCI Latency Timer is not expired. When the Latency Timer is 0 and GNT is deasserted, the Am79C978 controller will finish the current data phase, deassert FRAME, finish the last data phase, and release the bus. If EXTREQ (BCR18, bit 8) is cleared to 0, it will immediately assert REQ to regain bus ownership as soon as possible. If EXTREQ is set to 1, REQ will stay asserted. Am79C978 CLK 1 2 3 4 5 6 7 FRAME AD C/BE ADDR DATA 0111 0000 PAR PAR TheAm79C978 controller will reset all CSR locations to their STOP_RESET values. The BCR and PCI configuration registers will not be cleared. Any on-going network transmission is terminated in an orderly sequence. If less than 512 bits have been transmitted onto the network, the transmission will be terminated immediately, generating a runt packet. If 512 bits or more have been transmitted, the message will have the current FCS inverted and appended at the next byte boundary to guarantee an FCS error is detected at the receiving station. RMABORT (in the PCI Status register, bit 13) will be set to indicate that the Am79C978 controller has terminated its transaction with a master abort. In addition, SINT (CSR5, bit 11) will be set to 1. When SINT is set, INTA is asserted if the enable bit SINTE (CSR5, bit 10) is set to 1. This mechanism can be used to inform the driver of the system error. The host can read the PCI Status register to determine the exact cause of the interrupt. See Figure 23. PAR IRDY TRDY DEVSEL Parity Error Response STOP REQ GNT DEVSEL is sampled 22206B-23 Figure 20. Target Abort During every data phase of a DMA read operation, when the target indicates that the data is valid by asserting TRDY, the Am79C978 controller samples the AD[31:0], C/BE[3:0], and the PAR lines for a data parity error. When it detects a data parity error, the Am79C978 controller sets PERR (PCI Status register, bit 15) to 1. When reporting of that error is enabled by setting PERREN (PCI Command register, bit 6) to 1, the Am79C978 controller also drives the PERR signal low and sets DATAPERR (PCI Status register, bit 8) to 1. The assertion of PERR follows the corrupted data/ byte enables by two clock cycles and PAR by one clock cycle. When the preemption occurs after the counter has counted down to 0, the Am79C978 controller will finish the current data phase, deassert FRAME, finish the last data phase, and release the bus. Note that it is important for the host to program the PCI Latency Timer according to the bus bandwidth requirement of the Am79C978 controller. The host can determine this bus bandwidth requirement by reading the PCI MAX_LAT and MIN_GNT registers. Figure 24 shows a transaction that has a parity error in the data phase. TheAm79C978 controller asserts PERR on clock 8, two clock cycles after data is valid. The data on clock 5 is not checked for parity, because on a read access, PAR is only required to be valid one c l o c k a f t e r t h e t a r g e t h a s a s s e r t e d T R D Y. TheAm79C978 controller then drives PERR high for one clock cycle, since PERR is a sustained tri-state signal. Figure 22 assumes that the PCI Latency Timer has counted down to 0 on clock 7. During every data phase of a DMA write operation, the Am79C978 controller checks the PERR input to see if the target reports a parity error. When it sees the PERR input asserted, the Am79C978 controller sets PERR (PCI Status register, bit 15) to 1. When PERREN (PCI Command register, bit 6) is set to 1, the Am79C978 controller also sets DATAPERR (PCI Status register, bit 8) to 1. Master Abort TheAm79C978 controller will terminate its cycle with a Master Abort sequence if DEVSEL is not asserted within 4 clocks after FRAME is asserted. Master Abort is treated as a fatal error by the Am79C978 controller. Am79C978 49 CLK 1 2 3 4 5 6 7 FRAME AD C/BE ADDR DATA 0111 BE PAR PAR PAR IRDY TRDY DEVSEL REQ GNT 22206B-24 DEVSEL is sampled Figure 21. Preemption During Non-Burst Transaction CLK 1 2 3 4 5 6 7 8 ADDR DATA DATA DATA DATA DATA PAR PAR 9 FRAME AD 0111 C/BE BE PAR PAR PAR PAR PAR IRDY TRDY DEVSEL REQ GNT DEVSEL is sampled Figure 22. 50 22206B-25 Preemption During Burst Transaction Am79C978 CLK 1 2 3 4 5 7 6 8 9 FRAME AD C/BE ADDR DATA 0111 0000 PAR PAR PAR IRDY TRDY DEVSEL REQ GNT DEVSEL is sampled 22206B-26 Figure 23. Master Abort CLK 1 2 3 4 5 6 7 8 9 FRAME AD C/BE DATA ADDR 0111 BE PAR PAR PAR PERR IRDY TRDY DEVSEL DEVSEL is sampled 22206B-27 Figure 24. Master Cycle Data Parity Error Response Am79C978 51 Whenever the Am79C978 controller is the current bus master and a data parity error occurs, SINT (CSR5, bit 11) will be set to 1. When SINT is set, INTA is asserted if the enable bit SINTE (CSR5, bit 10) is set to 1. This mechanism can be used to inform the driver of the system error. The host can read the PCI Status register to determine the exact cause of the interrupt. The setting of SINT due to a data parity error is not dependent on the setting of PERREN (PCI Command register, bit 6). By default, a data parity error does not affect the state of the MAC engine. TheAm79C978 controller treats the data in all bus master transfers that have a parity error as if nothing has happened. All network activity continues. Advanced Parity Error Handling For all DMA cycles, the Am79C978 controller provides a second, more advanced level of parity error handling. This mode is enabled by setting APERREN (BCR20, bit 10) to 1. When APERREN is set to 1, the BPE bits (RMD1 and TMD1, bit 23) are used to indicate parity error in data transfers to the receive and transmit buffers. Note that since the advanced parity error handling uses an additional bit in the descriptor, SWSTYLE (BCR20, bits 7-0) must be set to 2 or 3 to program the Am79C978 controller to use 32-bit software structures. TheAm79C978 controller will react in the following way when a data parity error occurs: n Initialization block read: STOP (CSR0, bit 2) is set to 1 and causes a STOP_RESET of the device. n Descriptor ring read: Any on-going network activity is terminated in an orderly sequence and then STOP (CSR0, bit 2) is set to 1 to cause a STOP_RESET of the device. n Descriptor ring write: Any on-going network activity is terminated in an orderly sequence and then STOP (CSR0, bit 2) is set to 1 to cause a STOP_RESET of the device. n Transmit buffer read: BPE (TMD1, bit 23) is set in the current transmit descriptor. Any on-going network transmission is terminated in an orderly sequence. n Receive buffer write: BPE (RMD1, bit 23) is set in the last receive descriptor associated with the frame. Terminating on-going network transmission in an orderly sequence means that if less than 512 bits have been transmitted onto the network, the transmission 52 will be terminated immediately, generating a runt packet. If 512 bits or more have been transmitted, the message will have the current FCS inverted and appended at the next byte boundary to guarantee an FCS error is detected at the receiving station. APERREN does not affect the reporting of address parity errors or data parity errors that occur when the Am79C978 controller is the target of the transfer. Initialization Block DMA Transfers During execution of the Am79C978 controller bus master initialization procedure, the microcode will repeatedly request DMA transfers from the BIU. During each of these initialization block DMA transfers, the BIU will perform two data transfer cycles reading one DWord per transfer and then it will relinquish the bus. When SSIZE32 (BCR20, bit 8) is set to 1 (i.e., the initialization block is organized as 32-bit software structures), there are seven DWords to transfer during the bus master initialization procedure, so four bus mastership periods are needed in order to complete the initialization sequence. Note that the last DWord transfer of the last bus mastership period of the initialization sequence accesses an unneeded location. Data from this transfer is discarded internally. When SSIZE32 is cleared to 0 (i.e., the initialization block is organized as 16-bit software structures), then three bus mastership periods are needed to complete the initialization sequence. The Am79C978 device supports two transfer modes for reading the initialization block: non-burst and burst mode, with burst mode being the preferred mode when the Am79C978 controller is used in a PCI bus application. See Figure 25 and Figure 26. When BREADE is cleared to 0 (BCR18, bit 6), all initialization block read transfers will be executed in nonburst mode. There is a new address phase for every data phase. FRAME will be dropped between the two transfers. The two phases within a bus mastership period will have addresses of ascending contiguous order. When BREADE is set to 1 (BCR18, bit 6), all initialization block read transfers will be executed in burst mode. AD[1:0] will be 0 during the address phase indicating a linear burst order. Am79C978 CLK 1 2 3 4 5 6 7 8 9 10 FRAME AD 0110 C/BE 0000 PAR 0110 0000 PAR PAR PAR DATA IADDi+4 DATA IADDi PAR IRDY TRDY DEVSEL REQ GNT 22206B-28 DEVSEL is sampled Figure 25. Initialization Block Read In Non-Burst Mode CLK 1 2 3 4 5 6 7 FRAME AD IADDi DATA C/BE 0110 0000 PAR PAR DATA PAR PAR IRDY TRDY DEVSEL REQ GNT DEVSEL is sampled 22206B-29 Figure 26. Initialization Block Read In Burst Mode Am79C978 53 Descriptor DMA Transfers The Am79C978 microcode will determine when a descriptor access is required. A descriptor DMA read will consist of two data transfers. A descriptor DMA write will consist of one or two data transfers. The descriptor DMA transfers within a single bus mastership period will always be of the same type (either all read or all write). During descriptor read accesses, the byte enable signals will indicate that all byte lanes are active. Should some of the bytes not be needed, then the Am79C978 controller will internally discard the extraneous information that was gathered during such a read. The settings of SWSTYLE (BCR20, bits 7-0) and BREADE (BCR18, bit 6) affect the way the Am79C978 controller performs descriptor read operations. When SWSTYLE is set to 0 or 2, all descriptor read operations are performed in non-burst mode. The setting of BREADE has no effect in this configuration. See Figure 27. When SWSTYLE is set to 3, the descriptor entries are ordered to allow burst transfers. TheAm79C978 controller will perform all descriptor read operations in burst mode, if BREADE is set to 1. See Figure 28. of BWRITE has no effect in this configuration. See Figure 29. When SWSTYLE is set to 3, the descriptor entries are ordered to allow burst transfers. TheAm79C978 controller will perform all descriptor write operations in burst mode, if BWRITE is set to 1. See Figure 30 and Table 9 for the descriptor write sequence. A write transaction to the descriptor ring entries is the only case where the Am79C978 controller inserts a wait state when being the bus master. Every data phase in non-burst and burst mode is extended by one clock cycle, during which IRDY is deasserted. Note that Figure 28 assumes that the Am79C978 controller is programmed to use 32-bit software structures (SWSTYLE = 2 or 3). The byte enable signals for the second data transfer would be 0111b, if the device was programmed to use 16-bit software structures (SWSTYLE = 0). Table 8. SWSTYLE BCR20[7:0] Descriptor Read Sequence BREADE BCR18[6] Address = XXXX XX00h Turn around cycle Table 8 shows the descriptor read sequence. Data = MD1[31:24], MD0[23:0] During descriptor write accesses, only the byte lanes which need to be written are enabled. If buffer chaining is used, accesses to the descriptors of all intermediate buffers consist of only one data transfer to return ownership of the buffer to the system. When SWSTYLE (BCR20, bits 7-0) is cleared to 0 (i.e., the descriptor entries are organized as 16-bit software structures), the descriptor access will write a single byte. When SWSTYLE (BCR20, bits 7-0) is set to 2 or 3 (i.e., the descriptor entries are organized as 32-bit software structures), the descriptor access will write a single word. On all single buffer transmit or receive descriptors, as well as on the last buffer in chain, writes to the descriptor consist of two data transfers. The first data transfer writes a DWord containing status information. The second data transfer writes a byte (SWSTYLE cleared to 0), or otherwise a word containing additional status and the ownership bit (i.e., MD1[31]). 0 X When SWSTYLE is set to 0 or 2, all descriptor write operations are performed in non-burst mode. The setting Am79C978 Idle Address = XXXX XX04h Turn around cycle Data = MD2[15:0], MD1[15:0] Address = XXXX XX04h Turn around cycle Data = MD1[31:0] 2 X Idle Address = XXXX XX00h Turn around cycle Data = MD0[31:0] Address = XXXX XX04h Turn around cycle Data = MD1[31:0] 3 0 Idle Address = XXXX XX08h Turn around cycle Data = MD0[31:0] The settings of SWSTYLE (BCR20, bits 7-0) and BWRITE (BCR18, bit 5) affect the way the Am79C978 controller performs descriptor write operations. 54 AD Bus Sequence Address = XXXX XX04h 3 1 Turn around cycle Data = MD1[31:0] Data = MD0[31:0] CLK 1 2 3 4 5 6 7 8 9 10 FRAME AD MD1 C/BE 0110 DATA 0000 0110 0000 PAR PAR PAR PAR DATA MD0 PAR IRDY TRDY DEVSEL REQ GNT 22206B-30 DEVSEL is sampled Figure 27. Descriptor Ring Read In Non-Burst Mode CLK 1 2 3 4 5 6 DATA 7 FRAME AD MD1 DATA C/BE 0110 0000 PAR PAR PAR PAR IRDY TRDY DEVSEL REQ GNT DEVSEL is sampled 22206B-31 Figure 28. Descriptor Ring Read In Burst Mode Am79C978 55 CLK 1 2 3 4 5 6 7 8 9 10 FRAME AD MD2 C/BE 0111 0000 PAR DATA MD1 DATA 0111 PAR 0011 PAR PAR PAR IRDY TRDY DEVSEL REQ GNT 22206B-32 DEVSEL is sampled Figure 29. Descriptor Ring Write In Non-Burst Mode CLK 1 2 3 5 4 6 7 8 FRAME AD MD2 C/BE 0110 0000 PAR PAR DATA DATA 0011 PAR PAR IRDY TRDY DEVSEL REQ GNT 22206B-33 DEVSEL is sampled Figure 30. 56 Descriptor Ring Write In Burst Mode Am79C978 Table 9. SWSTYLE BCR20[7:0] Descriptor Write Sequence BWRITE BCR18[5] mastership period is dependent on all of the following variables: the settings of the FIFO watermarks, the conditions of the FIFOs, the latency of the system bus to the Am79C978 controller's bus request, the speed of bus operation and bus preemption events. The TRDY response time of the memory device will also affect the number of transfers, since the speed of the accesses will affect the state of the FIFO. During accesses, the FIFO may be filling or emptying on the network end. For example, on a receive operation, a slower TRDY response will allow additional data to accumulate inside of the FIFO. If the accesses are slow enough, a complete DWord may become available before the end of the bus mastership period and, thereby, increase the number of transfers in that period. The general rule is that the longer the Bus Grant latency, the slower the bus transfer operations; the slower the clock speed, the higher the transmit watermark; or the higher the receive watermark, the longer the bus mastership period will be. AD Bus Sequence Address = XXXX XX04h Data = MD2[15:0], MD1[15:0] 0 X Idle Address = XXXX XX00h Data = MD1[31:24] Address = XXXX XX08h Data = MD2[31:0] 2 X Idle Address = XXXX XX04h Data = MD1[31:16] Address = XXXX XX00h Data = MD2[31:0] 3 0 Idle Note: The PCI Latency Timer is not significant during non-burst transfers. Address = XXXX XX04h Data = MD1[31:16] Burst FIFO DMA Transfers Address = XXXX XX00h 3 1 Bursting is only performed by the Am79C978 controller if the BREADE and/or BWRITE bits of BCR18 are set. These bits individually enable/disable the ability of the Am79C978 controller to perform burst accesses during master read operations and master write operations, respectively. Data = MD2[31:0] Data = MD1[31:16] FIFO DMA Transfers The Am79C978 microcode will determine when a FIFO DMA transfer is required. This transfer mode will be used for transfers of data to and from the FIFOs. Once the BIU has been granted bus mastership, it will perform a series of consecutive transfer cycles before relinquishing the bus. All transfers within the master cycle will be either read or write cycles, and all transfers will be to contiguous, ascending addresses. Both nonburst and burst cycles are used, with burst mode being the preferred mode when the device is used in a PCI bus application. A burst transaction will start with an address phase, followed by one or more data phases. AD[1:0] will always be 0 during the address phase indicating a linear burst order. Non-Burst FIFO DMA Transfers Figure 31 shows the beginning of a FIFO DMA write with the beginning of the buffer not aligned to a DWord boundary. TheAm79C978 controller starts off by writing only three bytes during the first data phase. This operation aligns the address for all other data transfers to a 32-bit boundary so that the Am79C978 controller can continue bursting full DWords. In the default mode, the Am79C978 controller uses non-burst transfers to read and write data when accessing the FIFOs. Each non-burst transfer will be performed sequentially with the issue of an address and the transfer of the corresponding data with appropriate output signals to indicate selection of the active data bytes during the transfer. FRAME will be deasserted after every address phase. Several factors will affect the length of the bus mastership period. The possibilities are as follows: Bus cycles will continue until the transmit FIFO is filled to its high threshold (read transfers) or the receive FIFO is emptied to its low threshold (write transfers). The exact number of total transfer cycles in the bus During FIFO DMA read operations, all byte lanes will always be active. TheAm79C978 controller will internally discard unused bytes. During the first and the last data phases of a FIFO DMA burst write operation, one or more of the byte enable signals may be inactive. All other data phases will always write a complete DWord. If a receive buffer does not end on a DWord boundary, the Am79C978 controller will perform a non-DWord write on the last transfer to the buffer. Figure 32 shows the final three FIFO DMA transfers to a receive buffer. Since there were only nine bytes of space left in the receive buffer, the Am79C978 controller bursts three data phases. The first two data phases write a full DWord, the last one only writes a single byte. Am79C978 57 Note that the Am79C978 controller will always perform a DWord transfer as long as it owns the buffer space, even when there are less than four bytes to write. For example, if there is only one byte left for the current receive frame, the Am79C978 controller will write a full DWord, containing the last byte of the receive frame in the least significant byte position (BSWP is cleared to 0, CSR3, bit 2). The content of the other three bytes is undefined. The message byte count in the receive descriptor always reflects the exact length of the received frame. CLK 1 2 3 4 5 6 7 FRAME AD ADD C/BE 0111 PAR DATA PAR DATA DATA 0000 1110 PAR PAR PAR IRDY CLK 1 2 3 4 5 6 TRDY FRAME AD ADD DATA C/BE 0111 0001 DATA DEVSEL DATA REQ 0000 GNT PAR PAR PAR PAR DEVSEL is sampled IRDY 22206B-35 Figure 32. TRDY FIFO Burst Write at End of Unaligned Buffer DEVSEL REQ GNT DEVSEL is sampled 22206B-34 Figure 31. FIFO Burst Write at Start of Unaligned Buffer TheAm79C978 controller will continue transferring FIFO data until the transmit FIFO is filled to its high threshold (read transfers) or the receive FIFO is emptied to its low threshold (write transfers), or the Am79C978 controller is preempted and the PCI Latency Timer is expired. The host should use the values in the PCI MIN_GNT and MAX_LAT registers to determine the value for the PCI Latency Timer. 58 The exact number of total transfer cycles in the bus mastership period is dependent on all of the following variables: the settings of the FIFO watermarks, the conditions of the FIFOs, the latency of the system bus to the Am79C978 controller's bus request, and the speed of bus operation. The TRDY response time of the memory device will also affect the number of transfers, since the speed of the accesses will affect the state of the FIFO. During accesses, the FIFO may be filling or emptying on the network end. For example, on a receive operation, a slower TRDY response will allow additional data to accumulate inside of the FIFO. If the accesses are slow enough, a complete DWord may become available before the end of the bus mastership period and, thereby, increase the number of transfers in that period. The general rule is that the longer the Bus Grant latency, the slower the bus transfer operations; the slower the clock speed, the higher the transmit watermark; or the lower the receive watermark, the longer the total burst length will be. When a FIFO DMA burst operation is preempted, the Am79C978 controller will not relinquish bus ownership until the PCI Latency Timer expires. Am79C978 Buffer Management Unit The Buffer Management Unit (BMU) is a microcoded state machine which implements the initialization procedure and manages the descriptors and buffers. The buffer management unit operates at half the speed of the CLK input. Initialization Initialization includes the reading of the initialization block in memory to obtain the operating parameters. The initialization block can be organized in two ways. When SSIZE32 (BCR20, bit 8) is at its default value of 0, all initialization block entries are logically 16-bits wide to be backwards compatible with the Am79C90 C-LANCE and Am79C96x PCnet-ISA family. When SSIZE32 (BCR20, bit 8) is set to 1, all initialization block entries are logically 32-bits wide. Note that the Am79C978 controller always performs 32-bit bus transfers to read the initialization block entries. The initialization block is read when the INIT bit in CSR0 is set. The INIT bit should be set before or concurrent with the STRT bit to insure correct operation. Once the initialization block has been completely read in and internal registers have been updated, IDON will be set in CSR0, generating an interrupt (if IENA is set). The Am79C978 controller obtains the start address of the initialization block from the contents of CSR1 (least significant 16 bits of address) and CSR2 (most significant 16 bits of address). The host must write CSR1 and CSR2 before setting the INIT bit. The initialization block contains the user defined conditions for operation, together with the base addresses and length information of the transmit and receive descriptor rings. There is an alternate method to initialize the Am79C978 controller. Instead of initialization via the initialization block in memory, data can be written directly into the appropriate registers. Either method or a combination of the two may be used at the discretion of the programmer. Please refer to Appendix A, Alternative Method for Initialization for details on this alternate method. Re-Initialization Th e tr an s m i tt e r a n d r e c ei v e r s ec t i on s of t h e Am79C978 controller can be turned on via the initialization block (DTX, DRX, CSR15, bits 1-0). The states of the transmitter and receiver are monitored by the ho st throu gh CS R0 (RX O N, TX ON bi ts ). Th e Am79C978 controller should be re-initialized if the transmitter and/or the receiver were not turned on during the original initialization and it was subsequently required to activate them, or if either section was shut off due to the detection of an error condition (MERR, UFLO, TX BUFF error). Re-initialization may be done via the initialization block or by setting the STOP bit in CSR0, followed by writing to CSR15, and then setting the START bit in CSR0. Note that this form of restart will not perform the same in the Am79C978 controller as in the C-LANCE device. In particular, upon restart, the Am79C978 controller reloads the transmit and receive descriptor pointers with their respective base addresses. This means that the software must clear the descriptor OWN bits and reset its descriptor ring pointers before restarting the Am79C978 controller. The reload of descriptor base addresses is performed in the C-LANCE device only after initialization, so that a restart of the C-LANCE without initialization leaves the C-LANCE pointing at the same descriptor locations as before the restart. Suspend The Am79C978 controller offers two suspend modes that allow easy updating of the CSR registers without going through a full re-initialization of the device. The suspend modes also allow stopping the device with orderly termination of all network activity. The host requests the Am79C978 controller to enter the suspend mode by setting SPND (CSR5, bit 0) to 1. The host must poll SPND until it reads back 1 to determine that the Am79C978 controller has entered the suspend mode. When the host sets SPND to 1, the procedure taken by the Am79C978 controller to enter the suspend mode depends on the setting of the fast suspend enable bit (FASTSPND, CSR7, bit 15). When a fast suspend is requested (FASTSPND is set to 1), the Am79C978 controller performs a quick entry into the suspend mode. At the time the SPND bit is set, the Am79C978 controller will continue the DMA process of any transmit and/or receive packets that have already begun DMA activity until the network activity has been completed. In addition, any transmit packet that had started transmission will be fully transmitted and any receive packet that had begun reception will be fully received. However, no additional packets will be transmitted or received and no additional transmit or receive DMA activity will begin after network activity has ceased. Hence, the Am79C978 controller may enter the suspend mode with transmit and/or receive packets still in the FIFOs or the SRAM. This offers a worst case suspend time of a maximum length packet over the possibility of completely emptying the SRAM. Care must be exercised in this mode, because the entire memory subsystem of the Am79C978 controller is suspended. Any changes to either the descriptor rings or the SRAM can cause the Am79C978 controller to start up in an unknown condition and could cause data corruption. When FASTSPNDE is 0 and the SPND bit is set, the Am79C978 controller may take longer before entering the suspend mode. At the time the SPND bit is set, the Am79C978 controller will complete the DMA process of a transmit packet if it had already begun, and the Am79C978 59 Am79C978 controller will completely receive a receive packet if it had already begun. TheAm79C978 controller will not receive any new packets after the completion of the current reception. Additionally, all transmit packets stored in the transmit FIFOs and the transmit buffer area in the SRAM (if one is present) will be transmitted, and all receive packets stored in the receive FIFOs and the receive buffer area in the SRAM (if selected) will be transferred into system memory. Since the FIFO and the SRAM contents are flushed, it may take much longer before the Am79C978 controller enters the suspend mode. The amount of time that it takes depends on many factors including the size of the SRAM, bus latency, and network traffic level. Upon completion of the described operations, the Am79C978 controller sets the read-version of SPND to 1 and enters the suspend mode. In suspend mode, all of the CSR and BCR registers are accessible. As long as the Am79C978 controller is not reset while in suspend mode (by H_RESET, S_RESET, or by setting the STOP bit), no re-initialization of the device is required after the device comes out of suspend mode. When SPND is set to 0, the Am79C978 controller will leave the suspend mode and will continue at the transmit and receive descriptor ring locations where it was when it entered the suspend mode. See the section on Magic Packet technology for details on how that affects suspension of the integrated Ethernet controller. Buffer Management Buffer management is accomplished through message descriptor entries organized as ring structures in memory. There are two descriptor rings, one for transmit and one for receive. Each descriptor describes a single buffer. A frame may occupy one or more buffers. If multiple buffers are used, this is referred to as buffer chaining. Descriptor Rings Each descriptor ring must occupy a contiguous area of memory. During initialization, the user-defined base address for the transmit and receive descriptor rings, as well as the number of entries contained in the descriptor rings are set up. The programming of the software style (SWSTYLE, BCR20, bits 7-0) affects the way the descriptor rings and their entries are arranged. When SWSTYLE is at its default value of 0, the descriptor rings are backwards compatible with the Am79C90 C-LANCE and the Am79C96x PCnet-ISA family. The descriptor ring base addresses must be aligned to an 8-byte boundary and a maximum of 128 ring entries is allowed when the ring length is set through the TLEN and RLEN fields of the initialization block. Each ring entry contains a subset of the three 60 32-bit transmit or receive message descriptors (TMD, RMD) that are organized as four 16-bit structures (SSIZE32 (BCR20, bit 8) is set to 0). Note that even though the Am79C978 controller treats the descriptor entries as 16-bit structures, it will always perform 32-bit bus transfers to access the descriptor entries. The value of CSR2, bits 15-8, is used as the upper 8-bits for all memory addresses during bus master transfers. When SWSTYLE is set to 2 or 3, the descriptor ring base addresses must be aligned to a 16-byte boundary, and a maximum of 512 ring entries is allowed when the ring length is set through the TLEN and RLEN fields of the initialization block. Each ring entry is organized as three 32-bit message descriptors (SSIZE32 (BCR20, bit 8) is set to 1). The fourth DWord is reserved. When SWSTYLE is set to 3, the order of the message descriptors is optimized to allow read and write access in burst mode. For any software style, the ring lengths can be set beyond this range (up to 65535) by writing the transmit and receive ring length registers (CSR76, CSR78) directly. Each ring entry contains the following information: n The address of the actual message data buffer in user or host memory n The length of the message buffer n Status information indicating the condition of the buffer To permit the queuing and de-queuing of message buffers, ownership of each buffer is allocated to either the Am79C978 controller or the host. The OWN bit within the descriptor status information, either TMD or RMD, is used for this purpose. When OWN is set to 1, it signifies that the Am79C978 controller currently has ownership of this ring descriptor and its associated buffer. Only the owner is permitted to relinquish ownership or to write to any field in the descriptor entry. A device that is not the current owner of a descriptor entry cannot assume ownership or change any field in the entry. A device may, however, read from a descriptor that it does not currently own. Software should always read descriptor entries in sequential order. When software finds that the current descriptor is owned by the Am79C978 controller, then the software must not read ahead to the next descriptor. The software should wait at a descriptor it does not own until the Am79C978 controller sets OWN to 0 to release ownership to the software. When LAPPEN (CSR3, bit 5) is set to 1, this rule is modified. See the LAPPEN description. At initialization, the Am79C978 controller reads the base address of both the transmit and receive descriptor rings into CSRs for use by the Am79C978 controller during subsequent operations. Am79C978 Figure 33 illustrates the relationship between the initialization base address, the initialization block, the receive and transmit descriptor ring base addresses, the receive and transmit descriptors, and the receive and transmit data buffers, when SSIZE32 is cleared to 0. Figure 34 illustrates when SSIZE32 is set to 1, the relationship between the initialization base address, the initialization block, the receive and transmit descriptor ring base addresses, the receive and transmit descriptors, and the receive and transmit data buffers. Note that the value of CSR2, bits 15-8, is used as the upper 8-bits for all memory addresses during bus master transfers. N N N N * * * Rcv Descriptor Ring CSR2 IADR[31:16] 1st desc. start CSR1 2nd desc. IADR[15:0] RMD RMD RMD RMD0 RMD Initialization Block RLE TLE MOD PADR[15:0] PADR[31:16] PADR[47:32] LADRF[15:0] LADRF[31:16] LADRF[47:32] LADRF[63:48] RDRA[15:0] RES RDRA[23:16] TDRA[15:0] RES TDRA[23:16] Data Buffer 1 Rcv Buffers Data Buffer 2 M M Data Buffer N M M * * Xmt Descriptor Ring 2nd desc. 1st desc. start TMD Xmt Buffers * TMD TMD Data Buffer 1 TMD Data Buffer 2 TMD Data Buffer M 22206B-36 Figure 33. 16-Bit Software Model Am79C978 61 . N N N N * * * CSR2 CSR1 IADR[31:16] IADR[15:0] Rcv Descriptor Ring 1st desc. start RMD 2nd desc. start RMD RMD RMD RMD Initialization Block TLE RES RLE RES MODE PADR[31:0] PADR[47:32] RES LADRF[31:0] LADRF[63:32] RDRA[31:0] TDRA[31:0] Data Buffer 1 Rcv Buffers Data Buffer 2 M M Data Buffer N M M * * * 1st desc. start TMD0 Xmt Buffers Xmt Descriptor Ring 2nd desc. start TMD0 TMD1 TMD2 TMD3 Data Buffer 1 Data Buffer 2 Data Buffer M 22206B-37 Figure 34. 32-Bit Software Model Polling If there is no network channel activity and there is no pre- or post-receive or pre- or post-transmit activity being performed by the Am79C978 controller, then the Am79C978 controller will periodically poll the current receive and transmit descriptor entries in order to ascertain their ownership. If the DPOLL bit in CSR4 is set, then the transmit polling function is disabled. A typical polling operation consists of the following sequence. TheAm79C978 controller will use the current receive descriptor address stored internally to vector to the appropriate Receive Descriptor Table Entry (RDTE). It will then use the current transmit descriptor address (stored internally) to vector to the appropriate Transmit Descriptor Table Entry (TDTE). The accesses will be made in the following order: RMD1, then RMD0 of the current RDTE during one bus arbitration, and after that, TMD1, then TMD0 of the current TDTE during a second bus arbitration. All information collected during polling activity will be stored internally in the appropriate CSRs, if the OWN bit is set (i.e., CSR18, 62 CSR19, CSR20, CSR21, CSR40, CSR42, CSR50, CSR52). A typical receive poll is the product of the following conditions: 1. The controller does not own the current RDTE and the poll time has elapsed and RXON = 1 (CSR0, bit 5), or 2. The controller does not own the next RDTE and there is more than one receive descriptor in the ring and the poll time has elapsed and RXON = 1. If RXON is cleared to 0, the Am79C978 controller will never poll RDTE locations. In order to avoid missing frames, the system should have at least one RDTE available. To minimize poll activity, two RDTEs should be available. In this case, the poll operation will only consist of the check of the status of the current TDTE. A typical transmit poll is the product of the following conditions: Am79C978 1. The controller does not own the current TDTE and TXDPOLL = 0 (CSR4, bit 12) and TXON = 1 (CSR0, bit 4) and the poll time has elapsed, or 2. The controller does not own the current TDTE and TXDPOLL = 0 and TXON = 1 and a frame has just been received, or 3. The controller does not own the current TDTE and TXDPOLL = 0 and TXON = 1 and a frame has just been transmitted. Setting the TDMD bit of CSR0 will cause the microcode controller to exit the poll counting code and immediately perform a polling operation. If RDTE ownership has not been previously established, then an RDTE poll will be performed ahead of the TDTE poll. If the microcode is not executing the poll counting code when the TDMD bit is set, then the demanded poll of the TDTE will be delayed until the microcode returns to the poll counting code. The user may change the poll time value from the default of 65,536 clock periods by modifying the value in the Polling Interval register (CSR47). Transmit Descriptor Table Entry If, after a Transmit Descriptor Table Entry (TDTE) access, the Am79C978 controller finds that the OWN bit of that TDTE is not set, the Am79C978 controller resumes the poll time count and re-examines the same TDTE at the next expiration of the poll time count. If the OWN bit of the TDTE is set, but the Start of Packet (STP) bit is not set, the Am79C978 controller will immediately request the bus in order to clear the OWN bit of this descriptor. (This condition would normally be found following a late collision (LCOL) or retry (RTRY) error that occurred in the middle of a transmit frame chain of buffers.) After resetting the OWN bit of this descriptor, the Am79C978 controller will again immediately request the bus in order to access the next TDTE location in the ring. If the OWN bit is set and the buffer length is 0, the OWN bit will be cleared. In the C-LANCE device, the buffer length of 0 is interpreted as a 4096-byte buffer. A zero length buffer is acceptable as long as it is not the last buffer in a chain (STP = 0 and ENP = 1). If the OWN bit and STP are set, then microcode control proceeds to a routine that will enable transmit data transfers to the FIFO. TheAm79C978 controller will look ahead to the next transmit descriptor after it has performed at least one transmit data transfer from the first buffer. If the Am79C978 controller does not own the next TDTE (i.e., the second TDTE for this frame), it will complete transmission of the current buffer and update the status of the current (first) TDTE with the BUFF and UFLO bits being set. If DXSUFLO (CSR3, bit 6) is cleared to 0, the underflow error will cause the transmitter to be disabled (CSR0, TXON = 0). TheAm79C978 controller will have to be re-initialized to restore the transmit function. Setting DXSUFLO to 1 enables the Am79C978 controller to gracefully recover from an underflow error. The device will scan the transmit descriptor ring until it finds either the start of a new frame or a TDTE it does not own. To avoid an underflow situation in a chained buffer transmission, the system should always set the transmit chain descriptor own bits in reverse order. If the Am79C978 controller does own the second TDTE in a chain, it will gradually empty the contents of the first buffer (as the bytes are needed by the transmit operation), perform a single-cycle DMA transfer to update the status of the first descriptor (clear the OWN bit in TMD1), and then it may perform one data DMA access on the second buffer in the chain before executing another lookahead operation. (i.e., a lookahead to the third descriptor.) It is imperative that the host system never reads the TDTE OWN bits out of order. TheAm79C978 controller normally clears OWN bits in strict FIFO order. However, the Am79C978 controller can queue up to two frames in the transmit FIFO. When the second frame uses buffer chaining, the Am79C978 controller might return ownership out of normal FIFO order. The OWN bit for the last (and maybe only) buffer of the first frame is not cleared until transmission is completed. During the transmission the Am79C978 controller will read in buffers for the next frame and clear their OWN bits for all but the last one. The first and all intermediate buffers of the second frame can have their OWN bits cleared before the Am79C978 controller returns ownership for the last buffer of the first frame. If an error occurs in the transmission before all of the bytes of the current buffer have been transferred, transmit status of the current buffer will be immediately updated. If the buffer does not contain the end of packet, the Am79C978 controller will skip over the rest of the frame which experienced the error. This is done by returning to the polling microcode where the Am79C978 controller will clear the OWN bit for all descriptors with OWN = 1 and STP = 0 and continue in like manner until a descriptor with OWN = 0 (no more transmit frames in the ring) or OWN = 1 and STP = 1 (the first buffer of a new frame) is reached. At the end of any transmit operation, whether successful or with errors, immediately following the completion of the descriptor updates, the Am79C978 controller will always perform another polling operation. As described earlier, this polling operation will begin with a check of the current RDTE, unless the Am79C978 controller already owns that descriptor. Then the Am79C978 controller will poll the next TDTE. If the transmit descriptor OWN bit has a 0 value, the Am79C978 controller will Am79C978 63 resume incrementing the poll time counter. If the transmit descriptor OWN bit has a value of 1, the Am79C978 controller will begin filling the FIFO with transmit data and initiate a transmission. This end-of-operation poll coupled with the TDTE lookahead operation allows the Am79C978 controller to avoid inserting poll time counts between successive transmit frames. By default, whenever the Am79C978 controller completes a transmit frame (either with or without error) and writes the status information to the current descriptor, then the TINT bit of CSR0 is set to indicate the completion of a transmission. This causes an interrupt signal if the IENA bit of CSR0 has been set and the TINTM bit of CSR3 is cleared. TheAm79C978 controller provides two modes to reduce the number of transmit interrupts. The interrupt of a successfully transmitted frame can be suppressed by setting TINTOKD (CSR5, bit 15) to 1. Another mode, which is enabled by setting LTINTEN (CSR5, bit 14) to 1, allows suppression of interrupts for successful transmissions for all but the last frame in a sequence. Receive Descriptor Table Entry If the Am79C978 controller does not own both the current and the next Receive Descriptor Table Entry (RDTE), then the Am79C978 controller will continue to poll according to the polling sequence described above. If the receive descriptor ring length is one, then there is no next descriptor to be polled. If a poll operation has revealed that the current and the next RDTE belong to the Am79C978 controller, then additional poll accesses are not necessary. Future poll operations will not include RDTE accesses as long as the Am79C978 controller retains ownership of the current and the next RDTE. When receive activity is present on the channel, the Am79C978 controller waits for the complete address of the message to arrive. It then decides whether to accept or reject the frame based on all active addressing schemes. If the frame is accepted, the Am79C978 controller checks the current receive buffer status register CRST (CSR41) to determine the ownership of the current buffer. If ownership is lacking, the Am79C978 controller will immediately perform a final poll of the current RDTE. If ownership is still denied, the Am79C978 controller has no buffer in which to store the incoming message. The MISS bit will be set in CSR0 and the Missed Frame Counter (CSR112) will be incremented. Another poll of the current RDTE will not occur until the frame has finished. If the Am79C978 controller sees that the last poll (either a normal poll, or the final effort described in the above paragraph) of the current RDTE shows valid ownership, it proceeds to a poll of the next RDTE. Fol- 64 lowing this poll, and regardless of the outcome of this poll, transfers of receive data from the FIFO may begin. Regardless of ownership of the second receive descriptor, the Am79C978 controller will continue to perform receive data DMA transfers to the first buffer. If the frame length exceeds the length of the first buffer, and the Am79C978 controller does not own the second buffer, ownership of the current descriptor will be passed back to the system by writing a 0 to the OWN bit of RMD1. Status will be written indicating buffer (BUFF = 1) and possibly overflow (OFLO = 1) errors. If the frame length exceeds the length of the first (current) buffer, and the Am79C978 controller does own the second (next) buffer, ownership will be passed back to the system by writing a 0 to the OWN bit of RMD1 when the first buffer is full. The OWN bit is the only bit modified in the descriptor. Receive data transfers to the second buffer may occur before the Am79C978 controller proceeds to look ahead to the ownership of the third buffer. Such action will depend upon the state of the FIFO when the OWN bit has been updated in the first descriptor. In any case, lookahead will be performed to the third buffer and the information gathered will be stored in the chip, regardless of the state of the ownership bit. This activity continues until the Am79C978 controller recognizes the completion of the frame (the last byte of this receive message has been removed from the FIFO). TheAm79C978 controller will subsequently update the current RDTE status with the end of frame (ENP) indication set, write the message byte count (MCNT) for the entire frame into RMD2, and overwrite the "current" entries in the CSRs with the "next" entries. Receive Frame Queuing TheAm79C978 controller supports the lack of RDTEs when SRAM (SRAM SIZE in BCR 25, bits 7-0) is enabled through the Receive Frame Queuing mechanism. When the SRAM SIZE = 0, then the Am79C978 controller reverts back to the PCnet-PCI II mode of operation. This operation is automatic and does not require any programming by the host. When SRAM is enabled, the Receive Frame Queuing mechanism allows a slow protocol to manage more frames without the high frame loss rate normally attributed to FIFObased network controllers. TheAm79C978 controller will store the incoming frames in the extended FIFOs until polling takes place, if enabled and it discovers it owns an RDTE. The stored frames are not altered in any way until written out into system buffers. When the receive FIFO overflows, further incoming receive frames will be missed during that time. As soon as the network receive FIFO is empty, incoming frames are processed as normal. Status on a per frame basis is not kept during the overflow process. Am79C978 Statistic counters are maintained and accurate during that time. During the time that the Receive Frame Queuing mechanism is in operation, the Am79C978 controller relies on the Receive Poll Time Counter (CSR 48) to control the worst case access to the RDTE. The Receive Poll Time Counter is programmed through the Receive Polling Interval (CSR49) register. The Received Polling Interval defaults to approximately 2 ms. TheAm79C978 controller will also try to access the RDTE during normal descriptor accesses whether they are transmit or receive accesses. The host can force the Am79C978 controller to immediately access the RDTE by setting the RDMD (CSR 7, bit 13) to 1. Its operation is similar to the transmit one. The polling process can be disabled by setting the RXDPOLL (CSR7, bit 12) bit. This will stop the automatic polling process and the host must set the RDMD bit to initiate the receive process into host memory. Receive frames are still stored even when the receive polling process is disabled. Software Interrupt Timer TheAm79C978 controller is equipped with a software programmable free-running interrupt timer. The timer is constantly running and will generate an interrupt STINT (CSR 7, bit 11) when STINITE (CSR 7, bit 10) is set to 1. After generating the interrupt, the software timer will load the value stored in STVAL and restart. The timer value STVAL (BCR31, bits 15-0) is interpreted as an unsigned number with a resolution of 256 Time Base Clock periods. For instance, a value of 122 ms would be programmed with a value of 9531 (253Bh), if the Time Base Clock is running at 20 MHz. The default value of STVAL is FFFFh which yields the approximate maximum 838 ms timer duration. A write to STVAL restarts the timer with the new contents of STVAL. 10/100 Media Access Controller The Media Access Controller (MAC) engine incorporates the essential protocol requirements for operation of an Ethernet/IEEE 802.3-compliant node and provides the interface between the FIFO subsystem and the internal PHY. This section describes operation of the MAC engine when operating in half-duplex mode. When operating in half-duplex mode, the MAC engine is fully compliant to Section 4 of ISO/IEC 8802-3 (ANSI/IEEE Standard 1990 Second Edition) and ANSI/IEEE 802.3 (1985). When operating in full-duplex mode, the MAC engine behavior changes as described in the section FullDuplex Operation. The MAC engine provides programmable enhanced features designed to minimize host supervision, bus utilization, and pre- or post-message processing. These features include the ability to disable retries after a collision, dynamic FCS generation on a frame-byframe basis, automatic pad field insertion and deletion to enforce minimum frame size attributes, automatic retransmission without reloading the FIFO, and automatic deletion of collision fragments. The two primary attributes of the MAC engine are: n Transmit and receive message data encapsulation -- Framing (frame boundary delimitation, frame synchronization) -- Addressing (source and destination address handling) -- Error detection (physical medium transmission errors) n Media access management -- Medium allocation (collision avoidance, except in full-duplex operation) -- Contention resolution (collision handling, except in full-duplex operation) Transmit and Receive Message Data Encapsulation The MAC engine provides minimum frame size enforcement for transmit and receive frames. When APAD_XMT (CSR, bit 11) is set to 1, transmit messages will be padded with sufficient bytes (containing 00h) to ensure that the receiving station will observe an information field (destination address, source address, length/type, data, and FCS) of 64 bytes. When ASTRP_RCV (CSR4, bit 10) is set to 1, the receiver will automatically strip pad bytes from the received message by observing the value in the length field and by stripping excess bytes if this value is below the minimum data size (46 bytes). Both features can be independently over-ridden to allow illegally short (less than 64 bytes of frame data) messages to be transmitted and/or received. The use of this feature reduces bus utilization because the pad bytes are not transferred into or out of main memory. Framing The MAC engine will autonomously handle the construction of the transmit frame. Once the transmit FIFO has been filled to the predetermined threshold (set by XMTSP in CSR80) and access to the channel is currently permitted, the MAC engine will commence the 7byte preamble sequence (10101010b, where first bit transmitted is a 1). The MAC engine will subsequently append the Star t Frame Delimiter (SFD) byte (10101011b) followed by the serialized data from the transmit FIFO. Once the data has been completed, the MAC engine will append the FCS (most significant bit first), which was computed on the entire data portion of the frame. The data portion of the frame consists of destination address, source address, length/type, and frame data. The user is responsible for the correct or- Am79C978 65 dering and content in each of these fields in the frame. The MAC does not use the content in the length/type field unless APAD_XMT (CSR4, bit 11) is set and the data portion of the frame is shorter than 60 bytes. The MAC engine will detect the incoming preamble sequence when the RX_DV signal is activated by the internal PHY. The MAC will discard the preamble and begin searching for the SFD. Once the SFD is detected, all subsequent nibbles are treated as part of the frame. The MAC engine will inspect the length field to ensure minimum frame size, strip unnecessary pad characters (if enabled), and pass the remaining bytes through the receive FIFO to the host. If pad stripping is performed, the MAC engine will also strip the received FCS bytes, although normal FCS computation and checking will occur. Note that apart from pad stripping, the frame will be passed unmodified to the host. If the length field has a value of 46 or greater, all frame bytes including FCS will be passed unmodified to the receive buffer, regardless of the actual frame length. If the frame terminates or suffers a collision before 64 bytes of information (after SFD) have been received, the MAC engine will automatically delete the frame from the receive FIFO, without host intervention. TheAm79C978 controller has the ability to accept runt packets for diagnostic purposes and proprietary networks. Destination Address Handling The first 6 bytes of information after SFD will be interpreted as the destination address field. The MAC engine provides facilities for physical (unicast), logical (multicast), and broadcast address reception. Error Detection The MAC engine provides several facilities which report and recover from errors on the medium. In addition, it protects the network from gross errors due to inability of the host to keep pace with the MAC engine activity. On completion of transmission, the following transmit status is available in the appropriate Transmit Message Descriptor (TMD) and Control and Status Register (CSR) areas: n The number of transmission retry attempts (ONE, MORE, RTRY, and TRC). dicate a potentially faulty transceiver or network connection. n Late Collision (LCOL) indicates that the transmission suffered a collision after the slot time. This is indicative of a badly configured network. Late collisions should not occur in a normal operating network. n Collision Error (CERR) indicates that the transceiver did not respond with an SQE Test message within the first 4 ms after a transmission was completed. This may be due to a failed transceiver, disconnected or faulty transceiver drop cable, or because the transceiver does not support this feature (or it is disabled). SQE Test is only valid for 10Mbps networks. In addition to the reporting of network errors, the MAC engine will also attempt to prevent the creation of any network error due to the inability of the host to service the MAC engine. During transmission, if the host fails to keep the transmit FIFO filled sufficiently, causing an underflow, the MAC engine will guarantee the message is either sent as a runt packet (which will be deleted by the receiving station) or as an invalid FCS (which will also cause the receiver to reject the message). The status of each receive message is available in the appropriate Receive Message Descriptor (RMD) and CSR areas. All received frames are passed to the host regardless of any error. The FRAM error will only be reported if an FCS error is detected and there is a nonintegral number of bytes in the message. During the reception, the FCS is generated on every nibble (including the dribbling bits) coming from the cable, although the internally saved FCS value is only updated on the eighth bit (on each byte boundary). The MAC engine will ignore up to 7 additional bits at the end of a message (dribbling bits), which can occur under normal network operating conditions. The framing error is reported to the user as follows: n If the number of dribbling bits are 1 to 7 and there is no FCS error, then there is no Framing error (FRAM = 0). n If the number of dribbling bits are 1 to 7 and there is a FCS error, then there is also a Framing error (FRAM = 1). n Whether the MAC engine had to Defer (DEF) due to channel activity. n If the number of dribbling bits is 0, then there is no Framing error. There may or may not be a FCS error. n Excessive deferral (EXDEF), indicating that the transmitter experienced Excessive Deferral on this transmit frame, where Excessive Deferral is defined in the ISO 8802-3 (IEEE/ANSI 802.3) standard. n If the number of dribbling bits is 8, then there is no Framing error. FCS error will be reported, and the receive message count will indicate one extra byte. n Loss of Carrier (LCAR), indicating that there was an interruption in the ability of the MAC engine to monitor its own transmission. Repeated LCAR errors in- Counters are provided to report the Receive Collision Count and Runt Packet Count for network statistics and utilization calculations. 66 Am79C978 Media Access Management The basic requirement for all stations on the network is to provide fairness of channel allocation. The IEEE 802.3/Ethernet protocols define a media access mechanism which permits all stations to access the channel with equality. Any node can attempt to contend for the channel by waiting for a predetermined time (Inter Packet Gap) after the last activity, before transmitting on the media. The channel is a multidrop communications media (with various topological configurations permitted), which allows a single station to transmit and all other stations to receive. If two nodes simultaneously contend for the channel, their signals will interact causing loss of data, defined as a collision. It is the responsibility of the MAC to attempt to avoid and recover from a collision and to guarantee data integrity for the end-to-end transmission to the receiving station. Medium Allocation The IEEE/ANSI 802.3 standard (ISO/IEC 8802-3 1990) requires that the CSMA/CD MAC monitor the medium for traffic by watching for carrier activity. When carrier is detected, the media is considered busy, and the MAC should defer to the existing message. The ISO 8802-3 (IEEE/ANSI 802.3) standard also allows optionally a two-part deferral after a receive message. See ANSI/IEEE Std 802.3-1993 Edition, 4.2.3.2.1: Note: "It is possible for the PLS carrier sense indication to fail to be asserted during a collision on the media. If the deference process simply times the interframe gap based on this indication, it is possible for a short interframe gap to be generated, leading to a potential reception failure of a subsequent frame. To enhance system robustness, the following optional measures (as specified in 4.2.8) are recommended when InterFrameSpacingPart1 is other than 0: 1. Upon completing a transmission, start timing the interrupted gap as soon as transmitting and carrier sense are both false. 2. When timing an inter-frame gap following reception, reset the inter-frame gap timing if carrier sense becomes true during the first 2/3 of the inter-frame gap timing interval. During the final 1/3 of the interval, the timer shall not be reset to ensure fair access to the medium. An initial period shorter than 2/3 of the interval is permissible including 0." rier is deasserted. During the first part deferral (InterFrameSpacingPart1 - IFS1), the Am79C978 controller will defer any pending transmit frame and respond to the receive message. The IPG counter will be cleared to 0 continuously until the carrier deasserts, at which point the IPG counter will resume the 9.6 ms count once again. Once the IFS1 period of 6.0 ms has elapsed, the Am79C978 controller will begin timing the second part deferral (InterFrameSpacingPart2 - IFS2) of 3.4 ms. Once IFS1 has completed and IFS2 has commenced, the Am79C978 controller will not defer to a receive frame if a transmit frame is pending. This means that the Am79C978 controller will not attempt to receive the receive frame, since it will start to transmit and generate a collision at 9.6 ms. TheAm79C978 controller will complete the preamble (64-bit) and jam (32bit) sequence before ceasing transmission and invoking the random backoff algorithm. TheAm79C978 controller allows the user to program the IPG and the first-part deferral (InterFrameSpacingPart1 - IFS1) through CSR125. By changing the IPG default value of 96 bit times (60h), the user can adjust the fairness or aggressiveness of the MAC on the network. By programming a lower number of bit times than the ISO/IEC 8802-3 standard requires, the MAC engine will become more aggressive on the network. This aggressive nature will give rise to the Am79C978 controller possibly capturing the network at times by forcing other less aggressive compliant nodes to defer. By programming a larger number of bit times, the MAC will become less aggressive on the network and may defer more often than normal. The performance of the Am79C978 controller may decrease as the IPG value is increased from the default value, but the resulting behavior may improve network performance by reducing collisions. TheAm79C978 controller uses the same IPG for back-to-back transmits and receive-to-transmit accesses. Changing IFS1 will alter the period for which the MAC engine will defer to incoming receive frames. CAUTION: Care must be exercised when altering these parameters. Adverse network activity could result! The MAC engine implements the optional receive twopart deferral algorithm, with an InterFrameSpacingPart1 time of 6.0 ms. The InterFrameSpacingPart 2 interval is, therefore, 3.4 ms. This transmit two-part deferral algorithm is implemented as an option which can be disabled using the DXMT2PD bit in CSR3. The IFS1 programming will have no effect when DXMT2PD is set to 1, but the IPG programming value is still valid. Two part deferral after transmission is useful for ensuring that severe IPG shrinkage cannot occur in specific circumstances, causing a transmit message to follow a receive message so closely as to make them indistinguishable. TheAm79C978 controller will perform the two-part deferral algorithm as specified in the Process Deference section. The Inter Packet Gap (IPG) timer will start timing the 9.6 ms InterFrameSpacing after the receive car- During the time period immediately after a transmission has been completed, the external transceiver should generate the SQE Test message within 0.6 to 1.6 ms after the transmission ceases. During the time period in Am79C978 67 which the SQE Test message is expected, the Am79C978 controller will not respond to receive carrier sense. first collision. In this case, only the RTRY bit will be set, and the transmit message will be flushed from the FIFO. See ANSI/IEEE Std 802.3-1993 Edition, 7.2.4.6 (1): If a collision is detected after 512 bit times have been transmitted, the collision is termed a late collision. The MAC engine will abort the transmission, append the jam sequence, and set the LCOL bit. No retry attempt will be scheduled on detection of a late collision, and the transmit message will be flushed from the FIFO. "At the conclusion of the output function, the DTE opens a time window during which it expects to see the signal_quality_error signal asserted on the Control In circuit. The time window begins when the CARRIER_STATUS becomes CARRIER_OFF. If execution of the output function does not cause CARRIER_ON to occur, no SQE test occurs in the DTE. The duration of the window shall be at least 4.0 s but no more than 8.0 s. During the time window the Carrier Sense Function is inhibited." TheAm79C978 controller implements a carrier sense "blinding" period of 4.0 s length starting from the deassertion of carrier sense after transmission. This effectively means that when transmit two-part deferral is enabled (DXMT2PD is cleared), the IFS1 time is from 4 ms to 6 ms after a transmission. However, since IPG shrinkage below 4 ms will rarely be encountered on a correctly configured network, and since the fragment size will be larger than the 4 ms blinding window, the IPG counter will be reset by a worst case IPG shrinkage/fragment scenario and the Am79C978 controller will defer its transmission. If carrier is detected within the 4.0 to 6.0 ms IFS1 period, the Am79C978 controller will not restart the "blinding" period, but only restart IFS1. Collision Handling Collision detection is performed and reported to the MAC engine via the COL input pin. If a collision is detected before the complete preamble/ SFD sequence has been transmitted, the MAC engine will complete the preamble/SFD before appending the jam sequence. If a collision is detected after the preamble/SFD has been completed, but prior to 512 bits being transmitted, the MAC engine will abort the transmission and append the jam sequence immediately. The jam sequence is a 32-bit all zeros pattern. The MAC engine will attempt to transmit a frame a total of 16 times (initial attempt plus 15 retries) due to normal collisions (those within the slot time). Detection of collision will cause the transmission to be rescheduled to a time determined by the random backoff algorithm. If a single retry was required, the 1 bit will be set in the transmit frame status. If more than one retry was required, the MORE bit will be set. If all 16 attempts experienced collisions, the RTRY bit will be set (1 and MORE will be clear), and the transmit message will be flushed from the FIFO. If retries have been disabled by setting the DRTY bit in CSR15, the MAC engine will abandon transmission of the frame on detection of the 68 The ISO 8802-3 (IEEE/ANSI 802.3) Standard requires use of a "truncated binary exponential backoff" algorithm, which provides a controlled pseudo random mechanism to enforce the collision backoff interval, before retransmission is attempted. See ANSI/IEEE Std 802.3-1990 Edition, 4.2.3.2.5: "At the end of enforcing a collision (jamming), the CSMA/CD sublayer delays before attempting to retransmit the frame. The delay is an integer multiple of slot time. The number of slot times to delay before the nth retransmission attempt is chosen as a uniformly distributed random integer r in the range: 0 r < 2k Where k = Min (N,10)." TheAm79C978 controller provides an alternative algorithm, which suspends the counting of the slot time/IPG during the time that receive carrier sense is detected. This aids in networks where large numbers of nodes are present, and numerous nodes can be in collision. It effectively accelerates the increase in the backoff time in busy networks and allows nodes not involved in the collision to access the channel, while the colliding nodes await a reduction in channel activity. Once channel activity is reduced, the nodes resolving the collision time-out their slot time counters as normal. This modified backoff algorithm is enabled when EMBA (CSR3, bit 3) is set to 1. Transmit Operation The transmit operation and features of the Am79C978 controller are controlled by programmable options. TheAm79C978 controller offers a large transmit FIFO to provide frame buffering for increased system latency, automatic retransmission with no FIFO reload, and automatic transmit padding. Transmit Function Programming Automatic transmit features such as retry on collision, FCS generation/transmission, and pad field insertion can all be programmed to provide flexibility in the (re-) transmission of messages. Disable retry on collision (DRTY) is controlled by the DRTY bit of the Mode register (CSR15) in the initialization block. Am79C978 Automatic pad field insertion is controlled by the APAD_XMT bit in CSR4. APAD_XMT is 0, which will disable automatic pad generation after H_RESET. The disable FCS generation/transmission feature can be programmed as a static feature or dynamically on a frame-by-frame basis. It is the responsibility of upper layer software to correctly define the actual length field contained in the message to correspond to the total number of LLC data bytes encapsulated in the frame (length field as defined in the ISO 8802-3 (IEEE/ANSI 802.3) standard). The length value contained in the message is not used by the Am79C978 controller to compute the actual number of pad bytes to be inserted. TheAm79C978 controller will append pad bytes dependent on the actual number of bits transmitted onto the network. Once the last data byte of the frame has completed, prior to appending the FCS, the Am79C978 controller will check to ensure that 544 bits have been transmitted. If not, pad bytes are added to extend the frame size to this value, and the FCS is then added. See Figure 35. Transmit FIFO Watermark (XMTFW) in CSR80 sets the point at which the BMU requests more data from the transmit buffers for the FIFO. A minimum of XMTFW empty spaces must be available in the transmit FIFO before the BMU will request the system bus in order to transfer transmit frame data into the transmit FIFO. Transmit Start Point (XMTSP) in CSR80 sets the point when the transmitter actually attempts to transmit a frame onto the media. A minimum of XMTSP bytes must be written to the transmit FIFO for the current frame before transmission of the current frame will begin. (When automatically padded packets are being sent, it is conceivable that the XMTSP is not reached when all of the data has been transferred to the FIFO. In this case, the transmission will begin when all of the frame data has been placed into the transmit FIFO.) The default value of XMTSP is 01b, meaning there has to be 64 bytes in the transmit FIFO to start a transmission. The 544 bit count is derived from the following: Minimum frame size (excluding preamble/SFD, including FCS) 64 bytes 512 bits Preamble/SFD size 8 bytes 64 bits FCS size 32 bits 4 bytes The 544 bit count is derived from the following: Minimum frame size (excluding preamble/SFD, including FCS) 64 bytes 512 bits Automatic Pad Generation Transmit frames can be automatically padded to extend them to 64 data bytes (excluding preamble). This allows the minimum frame size of 64 bytes (512 bits) for IEEE 802.3/Ethernet to be guaranteed with no software intervention from the host/controlling process. Setting the APAD_XMT bit in CSR4 enables the automatic padding feature. The pad is placed between the LLC data field and FCS field in the IEEE 802.3 frame. FCS is always added if the frame is padded, regardless of the state of DXMTFCS (CSR15, bit 3) or ADD_FCS (TMD1, bit 29). The transmit frame will be padded by bytes with the value of 00h. The default value of Preamble/SFD size 8 bytes 64 bits FCS size 32 bits 4 bytes At the point that FCS is to be appended, the transmitted frame should contain: Preamble/SFD + (Min Frame Size - FCS) 64 + (512-32) = 544 bits A minimum length transmit frame from theAm79C978 controller, therefore, will be 576 bits after the FCS is appended. . Preamble 1010....1010 SFD 10101011 Destination Address Source Address Length 56 Bits 8 Bits 6 Bytes 6 Bytes 2 Bytes LLC Data Pad 4 Bytes 46 - 1500 Bytes Figure 35. FCS 22206B-38 ISO 8802-3 (IEEE/ANSI 802.3) Data Frame Am79C978 69 Transmit FCS Generation Automatic generation and transmission of FCS for a transmit frame depends on the value of DXMTFCS (CSR15, bit 3). If DXMTFCS is cleared to 0, the transmitter will generate and append the FCS to the transmitted frame. If the automatic padding feature is invoked (APAD_XMT is set in CSR4), the FCS will be appended by theAm79C978 controller regardless of the state of DXMTFCS or ADD_FCS (TMD1, bit 29). Note that the calculated FCS is transmitted most significant bit first. The default value of DXMTFCS is 0 after H_RESET. ADD_FCS (TMD1, bit 29) allows the automatic generation and transmission of FCS on a frame-by-frame basis. DXMTFCS should be cleared to 0 in this mode. To generate FCS for a frame, ADD_FCS must be set in all descriptors of a frame (STP is set to 1). Note that bit 29 of TMD1 has the function of ADD_FCS if SWSTYLE (BCR20, bits 7-0) is programmed to 0, 2, or 3. Transmit Exception Conditions Exception conditions for frame transmission fall into two distinct categories: those conditions which are the result of normal network operation, and those which occur due to abnormal network and/or host related events. Normal events which may occur and which are handled autonomously by theAm79C978 controller include collisions within the slot time with automatic retry. TheAm79C978 controller will ensure that collisions which occur within 512 bit times from the start of transmission (including preamble) will be automatically retried with no host intervention. The transmit FIFO ensures this by guaranteeing that data contained within the FIFO will not be overwritten until at least 64 bytes (512 bits) of preamble plus address, length, and data fields have been transmitted onto the network without encountering a collision. Note that if DRTY (CSR15, bit 5) is set to 1 or if the network interface is operating in full-duplex mode, no collision handling is required, and any byte of frame data in the FIFO can be overwritten as soon as it is transmitted. If 16 total attempts (initial attempt plus 15 retries) fail, theAm79C978 controller sets the RTRY bit in the current transmit TDTE in host memory (TMD2), gives up ownership (resets the OWN bit to 0) for this frame, and processes the next frame in the transmit ring for transmission. Abnormal network conditions include: n Loss of carrier n Late collision n SQE Test Error (does not apply to 100 Mbps networks.) 70 These conditions should not occur on a correctly configured IEEE 802.3 network operating in half-duplex mode. If they do, they will be reported. None of these conditions will occur on a network operating in fullduplex mode. (See the section Full-Duplex Operation for more detail.) When an error occurs in the middle of a multi-buffer frame transmission, the error status will be written in the current descriptor. The OWN bit(s) in the subsequent descriptor(s) will be cleared until the STP (the next frame) is found. Loss of Carrier LCAR will be reported for every frame transmitted if theAm79C978 controller detects a loss of carrier. Late Collision A late collision will be reported if a collision condition occurs after one slot time (512 bit times) after the transmit process was initiated (first bit of preamble commenced). TheAm79C978 controller will abandon the transmit process for that frame, set Late Collision (LCOL) in the associated TMD2, and process the next transmit frame in the ring. Frames experiencing a late collision will not be retried. Recovery from this condition must be performed by upper layer software. SQE Test Error If the network port is in Link Fail state, CERR will be asserted in the 10BASE-T mode after transmit. CERR will never cause INTA to be activated. It will, however, set the ERR bit CSR0. Receive Operation The receive operation and features of theAm79C978 controller are controlled by programmable options. TheAm79C978 controller offers a large receive FIFO to provide frame buffering for increased system latency, automatic flushing of collision fragments (runt packets), automatic receive pad stripping, and a variety of address match options. Receive Function Programming Automatic pad field stripping is enabled by setting the ASTRP_RCV bit in CSR4. This can provide flexibility in the reception of messages using the IEEE 802.3 frame format. All receive frames can be accepted by setting the PROM bit in CSR15. Acceptance of unicast and broadcast frames can be individually turned off by setting the DRCVPA or DRCVBC bits in CSR15. The Physical Address register (CSR12 to CSR14) stores the address that theAm79C978 controller compares to the destination address of the incoming frame for a unicast address match. The Logical Address Filter register (CSR8 to CSR11) serves as a hash filter for multicast address match. Am79C978 The point at which the BMU will start to transfer data from the receive FIFO to buffer memory is controlled by the RCVFW bits in CSR80. The default established during H_RESET is 01b, which sets the watermark flag at 64 bytes filled. For test purposes, theAm79C978 controller can be programmed to accept runt packets by setting RPA in CSR124. Address Matching TheAm79C978 controller supports three types of address matching: unicast, multicast, and broadcast. The normal address matching procedure can be modified by programming three bits in CSR15, the mode register (PROM, DRCVPA, and DRCVBC). If the first bit received after the SFD (the least significant bit of the first byte of the destination address field) is 0, the frame is unicast, which indicates that the frame is meant to be received by a single node. If the first bit received is 1, the frame is multicast, which indicates that the frame is meant to be received by a group of nodes. If the destination address field contains all 1s, the frame is broadcast, which is a special type of multicast. Frames with the broadcast address in the destination address field are meant to be received by all nodes on the local area network. When a unicast frame arrives at theAm79C978 controller, the Am79C978 controller will accept the frame if the destination address field of the incoming frame exactly matches the 6-byte station address stored in the Physical Address registers (PADR, CSR12 to CSR14). The byte ordering is such that the first byte received from the network (after the SFD) must match the least significant byte of CSR12 (PADR[7:0]), and the sixth byte received must match the most significant byte of CSR14 (PADR[47:40]). When DRCVPA (CSR15, bit 13) is set to 1,the Am79C978 controller will not accept unicast frames. If the incoming frame is multicast, the Am79C978 controller performs a calculation on the contents of the destination address field to determine whether or not to accept the frame. This calculation is explained in the Logical Address Filter (LADRF) bits description. When all bits of the LADRF registers are 0, no multicast frames are accepted, except for broadcast frames. Although broadcast frames are classified as special multicast frames, they are treated differently by the Am79C978 controller hardware. Broadcast frames are always accepted, except when DRCVBC (CSR15, bit 14) is set and there is no Logical Address match. miscuous mode. In the promiscuous mode, all properly formed packets are received, regardless of the contents of their destination address fields. The promiscuous mode overrides the Disable Receive Broadcast bit (DRCVBC bit l4 in the MODE register) and the Disable Receive Physical Address bit (DRCVPA, CSR15, bit 13). TheAm79C978 controller operates in promiscuous mode when PROM (CSR15, bit 15) is set. The receive descriptor entry RMD1 contains three bits that indicate which method of address matching caused the Am79C978 controller to accept the frame. Note that these indicator bits are only available when the Am79C978 controller is programmed to use 32-bit structures for the descriptor entries (BCR20, bit 7-0, SWSTYLE is set to 2 or 3). Physical Address Match (PAM) (RMD1, bit 22) is set by the Am79C978 controller when it accepts the received frame due to a match of the frame's destination address with the content of the physical address register. Logical Address Filter Match (LAFM) (RMD1, bit 21) is set by the Am79C978 controller when it accepts the received frame based on the value in the logical address filter register. Broadcast Address Match (BAM) (RMD1, bit 20) is set by the Am79C978 controller when it accepts the received frame because the frame's destination address is of the type 'Broadcast.' If DRCVBC (CSR15, bit 14) is cleared to 0, only BAM, but not LAFM will be set when a Broadcast frame is received, even if the Logical Address Filter is programmed in such a way that a Broadcast frame would pass the hash filter. If DRCVBC is set to 1 and the Logical Address Filter is programmed in such a way that a Broadcast frame would pass the hash filter, LAFM will be set on the reception of a Broadcast frame. When the Am79C978 controller operates in promiscuous mode and none of the three match bits is set, it is an indication that the Am79C978 controller has only accepted the frame because it was in promiscuous mode. When the Am79C978 controller is not programmed to be in promiscuous mode, then when none of the three match bits is set, it is an indication that the Am79C978 controller only accepted the frame because it was not rejected. See Table 10 for receive address matches. None of the address filtering described above applies when the Am79C978 controller is operating in the pro- Am79C978 71 Table 10. Receive Address Match PAM LAFM BAM DRCVBC Comment 802.3 Length field is not compliant with either standard and may cause problems if pad stripping is enabled. 0 0 0 X Frame accepted due to PROM = 1 1 0 0 X Physical address match 0 Logical address filter match; frame is not of type broadcast 1 Logical address filter match; frame can be of type broadcast 0 0 0 1 1 0 0 0 1 0 Broadcast frame Automatic Pad Stripping During reception of an IEEE 802.3 frame, the pad field can be stripped automatically. Setting ASTRP_RCV (CSR4, bit 0) to 1 enables the automatic pad stripping feature. The pad field will be stripped before the frame is passed to the FIFO, thus preserving FIFO space for additional frames. The FCS field will also be stripped, since it is computed at the transmitting station based on the data and pad field characters, and will be invalid for a receive frame that has had the pad characters stripped. The number of bytes to be stripped is calculated from the embedded length field (as defined in the ISO 88023 (IEEE/ANSI 802.3) definition) contained in the frame. The length indicates the actual number of LLC data bytes contained in the message. Any received frame which contains a length field less than 46 bytes will have the pad field stripped (if ASTRP_RCV is set). Receive frames which have a length field of 46 bytes or greater will be passed to the host unmodified. Receive FCS Checking Reception and checking of the received FCS is performed automatically by the Am79C978 controller. Note that if the Automatic Pad Stripping feature is enabled, the FCS for padded frames will be verified against the value computed for the incoming bit stream including pad characters, but the FCS value for a padded frame will not be passed to the host. If an FCS error is detected in any frame, the error will be reported in the CRC bit in RMD1. Receive Exception Conditions Exception conditions for frame reception fall into two distinct categories, i.e., those conditions which are the result of normal network operation, and those which occur due to abnormal network and/or host related events. Normal events which may occur and which are handled autonomously by the Am79C978 controller are basically collisions within the slot time and automatic runt packet rejection. The Am79C978 controller will ensure that collisions that occur within 512 bit times from the start of reception (excluding preamble) will be automatically deleted from the receive FIFO with no host intervention. The receive FIFO will delete any frame that is composed of fewer than 64 bytes provided that the Runt Packet Accept (RPA bit in CSR124) feature has not been enabled and the network interface is operating in half-duplex mode, or the full-duplex Runt Packet Accept Disable bit (FDRPAD, BCR9, bit 2) is set. This criterion will be met regardless of whether the receive frame was the first (or only) frame in the FIFO or if the receive frame was queued behind a previously received message. Figure 36 shows the byte/bit ordering of the received length field for an IEEE 802.3-compatible frame format. Abnormal network conditions include: Since any valid Ethernet Type field value will always be greater than a normal IEEE 802.3 Length field (46), the Am79C978 controller will not attempt to strip valid Ethernet frames. Note that for some network protocols, the value passed in the Ethernet Type and/or IEEE n Late collision 72 n FCS errors Host related receive exception conditions include MISS, BUFF, and OFLO. These are described in the Buffer Management Unit section. Am79C978 46 - 1500 Bytes 56 Bits 8 Bits 6 Bytes 6 Bytes 2 Bytes Preamble 1010....1010 SFD 10101011 Destination Address Source Address Length 4 Bytes LLC Data Pad 1 - 1500 Bytes 45 - 0 Bytes FCS Start of Frame at Time = 0 Bit 0 Bit 7 Bit 0 Bit 7 Increasing Time Most Significant Byte Least Significant Byte 22206B-39 Figure 36. IEEE 802.3 Frame and Length Field Transmission Order Loopback Operation Loopback is a mode of operation intended for system diagnostics. In this mode, the transmitter and receiver are both operating at the same time so that the Am79C978 controller receives its own transmissions. The Am79C978 controller provides two basic types of loopback. In internal loopback mode, the transmitted data is looped back to the receiver inside the Am79C978 controller without actually transmitting any data to the external network. The receiver will move the received data to the next receive buffer, where it can be examined by software. Alternatively, in external loopback mode, data can be transmitted to and received from the PHY. Refer to Table 30 for various bit settings required for Loopback modes. The external loopback requires a two-step operation. The internal PHY must be placed into a loopback mode by writing to the PHY Control Register (BCR33, BCR34). Then, the Am79C978 controller must be placed into an external loopback mode by setting the Loop bits. Miscellaneous Loopback Features All transmit and receive function programming, such as automatic transmit padding and receive pad stripping, operates identically in loopback as in normal operation. voked. This is to be backwards compatible to the C-LANCE (Am79C90) software. Since the Am79C978 controller has two FCS generators, there are no more restrictions on FCS generation or checking, or on testing multicast address detection as they exist in the half-duplex PCnet family devices and in the C-LANCE. On receive, the Am79C978 controller now provides true FCS status. The descriptor for a frame with an FCS error will have the FCS bit (RMD1, bit 27) set to 1. The FCS generator on the transmit side can still be disabled by setting DXMTFCS (CSR15, bit 3) to 1. In internal loopback operation, the Am79C978 controller provides a special mode to test the collision logic. When FCOLL (CSR15, bit 4) is set to 1, a collision is forced during every transmission attempt. This will result in a Retry error. Full-Duplex Operation TheAm79C978 controller supports full-duplex operation on the 10BASE-T and MII interfaces. Full-duplex operation allows simultaneous transmit and receive activity. Full-duplex operation is enabled by the FDEN bit located in BCR9. Full-duplex operation is also enabled through Auto-Negotiation when DANAS (BCR 32, bit 7) is not enabled and the ASEL bit is set, and its link partner is capable of Auto-Negotiation and full-duplex operation. Runt Packet Accept is internally enabled (RPA bit in CSR124 is not affected) when any loopback mode is in- Am79C978 73 When operating in full-duplex mode, the following changes to the device operation are made: Bus Interface/Buffer Management Unit changes: n The first 64 bytes of every transmit frame are not preserved in the Transmit FIFO during transmission of the first 512 bits as described in the Transmit Exception Conditions section. Instead, when full-duplex mode is active and a frame is being transmitted, the XMTFW bits (CSR80, bits 9-8) always govern when transmit DMA is requested. n Successful reception of the first 64 bytes of every receive frame is not a requirement for Receive DMA to begin as described in the Receive Exception Conditions section. Instead, receive DMA will be requested as soon as either the RCVFW threshold (CSR80, bits 12-13) is reached or a complete valid receive frame is detected, regardless of length. This Receive FIFO operation is identical to when the RPA bit (CSR124, bit 3) is set during half-duplex mode operation. packet ends, instead of when transmit and carrier activity ends. n The 4.0 s carrier sense blinding period after a transmission during which the SQE test normally occurs is disabled. n The collision indication input to the MAC engine is ignored. The internal PHY changes for full-duplex operation are as follows: n The collision detect (COL) pin is disabled. n The SQE test function is disabled. n Loss of Carrier (LCAR) reporting is disabled. n PHY Control Register (TBR0) bit 8 is set to 1 if AutoNegotiation is disabled. Full-Duplex Link Status LED Support The MAC engine changes for full-duplex operation are as follows: TheAm79C978 controller provides bits in each of the LED Status registers (BCR4, BCR5, BCR6, BCR7, and BCR48) to display the Full-Duplex Link Status. If the FDLSE bit (bit 8) is set, a value of 1 will be sent to the associated LEDOUT bit when in Full-Duplex. n Changes to the transmit deferral mechanism: PHY/MAC Interface -- Transmission is not deferred while receive is active. -- The IPG counter which governs transmit deferral during the IPG between back-to-back transmits is started when transmit activity for the first 74 The internal MII-compatible interface provides the data path connection between the 10BASE-T PHY, the 1 Mbps HomePNA PHY, and the 10/100 Media Access Controller (MAC). The interface is compatible with Clause 22 of the IEEE 802.3 standard specification. Am79C978 DETAILED FUNCTIONS 1 Mbps HomePNA PHY The integrated HomePNA transceiver is a physical layer device supporting the HomePNA specification 1.0 for home phone line networking. It provides all of the PHY layer functions required to support 1 Mbps data transfer speeds over common residential phone wiring. All data bits are encoded into the relative time position of a pulse with respect to the previous one, the waveform on the wire consists of a 7.5 MHz carrier sinusoid enclosed within an exponential (bell shaped) envelope. The waveform is produced by generating four 7.5 MHz square wave cycles and passing them through a bandpass filter. The HomePNA PHY frame consists of a HomePNA header that replaces the normal Ethernet 64-bit preamble and delimiter and is prepended to a standard Ethernet packet starting with the destination address and ending with the CRC. Only the PHY layer and its parameters are modified from that of the standard Ethernet implementation. The HomePNA PHY layer is designed to operate with the internal Ethernet MAC layer controller implementing all the CSMA/CD protocol features. The frame begins with a characteristic SYNC interval that delineates the beginning of a HomePNA frame followed by an Access ID (AID) which encodes 8 bits of Access ID and 4 bits of control word. The Access ID is used to detect collisions and is dynamically assigned, while the control word carries speed and power information. The AID is followed by a silence interval, then 32 bits of data reserved for PHY layer communication. These bits are accessible via HPR20 and HPR21 and are for future use. The data encoding consists of two symbol types: an AID symbol and a data symbol. The AID symbol is always transmitted at the same speed and encodes two bits that determine the pulse position (one of four) relative to the previous pulse. The access symbol interval is fixed. The data symbol interval is variable. The arriving bit stream is blocked into from 3 to 6 bit blocks according to a proprietary (RLL25TM) algorithm. The bits in each block are then used to encode a data symbol. Each symbol consists of a Data Inter Symbol Blanking Interval (DISBI) and then a pulse at one of twenty-five possible positions. The bits in the data block determine the pulse position. Immediately after the pulse a new symbol interval begins. During the DISBI the receiver ignores all incoming pulses to allow network reflections to die out. Any station may be programmed to assume the role of a PHY master and remotely command, via the control word, the rest of the units on the network to change their transmit speed or power level. Many of the framing parameters are programmable in the HomePNA PHY and will allow future modifications to both transmission speed as well as noise and reflection rejection algorithms. Two default speeds are provided, low at 0.7 Mbps and high at 1 Mbps. The center frequency is also programmable for future use. HomePNA PHY Medium Interface Framing The HomePNA frame on the phone wire network consists of a header generated in the PHY prepended to an IEEE 802.3 Ethernet data packet received from the MAC layer. See Figure 37. When transmitting on the phone wire pair, the HomePNA PHY first receives an Ethernet MAC frame from the MAC. The 8 octets of preamble and delimiter are stripped off and replaced with the HomePNA PHY header described below, then transmitted LSB first on the phone wire network. During a receive operation, the reverse process is executed. When a HomePNA frame is received by the PHY, the header is stripped off and replaced with the four octets of preamble and delimiter of the IEEE 802.3 Ethernet MAC frame specification and then passed on to the MAC layer. Am79C978 75 Ethernet Packet HomePNA Header SYNC interval Access ID AID blanking interval Fixed 14.93 s AID blanking interval 01 Silence AID blanking interval 11 AID blanking interval 10 AID blanking interval 00 01 Destination Source Length 6 6 2 PCOM 4 bytes AID blanking interval ETHERNET MAC and DATA max 1500 Silence interval 00 32 bits PCOM 60 tics 20 tics 66 tics potential pulse position pulse 129 tics 129 tics 129 tics 129 tics 129 tics 129 tics 129 tics 129 tics SYNC Symbol 0 ACCESS ID Symbol 1 ACCESS ID Symbol 2 ACCESS ID Symbol 3 ACCESS ID Symbol 4 ACCESS ID Symbol 5 ACCESS ID Symbol 6 ACCESS ID Symbol 7 ACCESS ID interval Fixed 119.44 s CRC 4 Ethernet Packet Data symbols 30.75 s @ 1 Mbps Example Access ID of 01110100 and control word 0100 HomePNA PHY Header 150.19 s @ 1 Mbps 1 Tic = 116.6667 ns = receiver blanking interval 22206B-41 Figure 37. HomePNA PHY Framing HomePNA Symbol Waveform These symbols are described in the following sections. All HomePNA symbols are composed at the transmitter of a silence interval, and a pulse formed of an integer number of cycles (TX_PULSE_CYCLES_P/N in HPR29) of a square wave of frequency (CENTER_FREQUENCY TX_PULSE_WIDTH in HPR29) that has been filtered with a bandpass filter. Data is encoded in the time interval from the preceding pulse. Symbol 0 (SYNC interval) Table 11. HomePNA PHY Pulse Parameters Parameter Value Tolerance Unit CENTER_FREQUENCY 7.5 500 PPM MHz CYCLES_PER_PULSE 4 -- Cycles Time Interval Unit HomePNA PHY time intervals are expressed in Time Interval Clock (TIC) units. One TIC is defined as 1/60E6 seconds or approximately 116.7 ns. ACCESS ID Intervals A HomePNA frame begins with an Access ID (AID) interval which is composed of eight equally spaced subintervals termed AID symbols 0 through 7 as shown in Figure 37. An AID symbol is 129 TICs long. Transmit timing is shown in Figure 38; receive timing in Figure 39. Timing starts at the beginning of each AID symbol at TIC = 0 and ends at TIC = 129. 76 SYNC Transmit Timing The SYNC interval (AID symbol 0) delineates the beginning of a HomePNA frame and is composed of a SYNC_START pulse, followed by a SYNC_END pulse, after a fixed silence interval as shown in Figure 38. Timing for this (AID symbol 0) starts (TIC = 0) at the beginning of the SYNC_START pulse. The SYNC_END pulse starts at TIC = 126. At TIC = 129, this AID symbol 0 ends and the next AID symbol begins, with the symbol timing reference reset to TIC = 0. No information bits are coded in the SYNC (AID symbol 0 interval). SYNC Receive Timing As soon as the SYNC_START pulse is detected the receiver disables (blanks) further detection until time TIC = 61, after which detection is re-enabled for the next received pulse. The receiver allows for jitter by establishing a window around each legal pulse position. This window is -2 +1 TICS wide on either side of the position. A SYNC_END pulse that arrives outside the window of the legal TIC = 126 is considered a noise event which is used in setting the adaptive squelch level, aborts the packet, and sets the receiver in search of a new SYNC_START pulse and SYNC interval. If it is a transmitting station, the COLLISION event is asserted as described in the Collisions section. Am79C978 Transmitter AID Symbol 0 AID Symbol 1 pulse 0 AID Symbol 2 pulse 2 shown in position 1 pulse 1 TIC=129 and TIC=0 SYNC_START TIC=0 TIC=129 and TIC=0 AID_Position_0 TIC=66 SYNC_END TIC=126 AID_Position_1 TIC=86 AID_Position_2 TIC=106 AID_Position_3 TIC=126 22206B-42 Figure 38. AID Symbol Transmit Timing Receiver AID slice threshold AID Symbol 1 AID Symbol 0 pulse 0 pulse 1 Detected envelope AID Symbol 2 pulse 2 shown in position 1 END_RCV_BLANK TIC=128 and TIC=0 SYNC_START TIC=0 AID_Position_0 TIC=66 AID_Position_1 TIC=86 TIC=12 8 and TIC=0 AID_GUARD_INTERVAL AID_Position_2 TIC=106 SYNC_END TIC=126 AID_Position_3 TIC=126 22206B-43 Figure 39. AID Symbol Receive Timing AID Symbols 1 through 6 AID symbols 1 through 4 are used to identify individual stations to enable reliable collision detection as described in the Collisions section. Symbols 5 and 6 are used to transmit remote control management commands across the network. Coding and timing details are as follows. The SYNC interval is followed by six AID symbols (symbols 1 through 6). Transmit timing is shown in Figure 38; receive timing in Figure 39. Data is encoded in the relative position of each pulse with respect to the previous one. A pulse may occur at one, and only one, of the four possible positions within an AID symbol yielding two bits of data coded per AID symbol. The decoded bits from the AID symbols 1 to 4 produce eight bits of Access ID which is used to identify individual HomePNA stations and to detect collisions. The MSB is encoded in AID Symbol 1 and is the leftmost bit in Table 12. Am79C978 77 Table 12. Access ID Symbol Pulse Positions and Encoding The following criteria must be met to guarantee reliable collision detection: Pulse Position TICs from Beginning of AID Symbol Bit Encoding At least one HomePNA station of a colliding group must always detect a collision when the delay between the beginning of its transmitted packet and the beginning of the received colliding packet is between -1.5 s and +1.5 s. 1 66 00 2 86 01 3 106 10 4 126 11 The next two AID symbols (5 and 6) encode four bits of control word information. The MSB is encoded in AID Symbol 5. Control word messages are described further in the Management Interfaces section. AID Transmit Timing The transmitter encodes the Access ID in a pulse position in each 128 TIC interval. Each AID symbol interval must have only one pulse. Pulse transmission must start in only one of the four possible positions (measured from the beginning of the Access ID symbol) defined in Table 12. AID Receive Timing The receiver allows for jitter by establishing a window around each legal pulse position. This window is -2 +1 TICS wide on either side of the position. A pulse that arrives outside of the legal AID positions is considered a COLLISION event. Collisions A Collision is detected only during Access ID and silent intervals (AID symbols 0 through 7). In general during a collision, a transmitting station will read back an AID value that does not match its own and recognizes the event as a collision and alerts other stations with a JAM signal. Non-transmitting stations may also detect some collisions by interpreting received non-conforming AID pulses as collisions. With two transmitters colliding, each transmitter normally blanks its receive input immediately after transmitting (and simultaneously receiving) a pulse. Therefore, only when a transmitting station receives pulses in a position earlier than the position it transmitted will it recognize it as a pulse transmitted by another station and signal a collision. For this reason, guaranteed collision detection is possible only as long as the spacing between successive possible pulse positions in an AID symbol (20 TICs or 2.3 s) is greater than the round trip delay between the colliding nodes. At approximately 1.5 ns propagation delay per foot, the maximum distance between two HomePNA units must not be greater than 500 feet for collision detection purposes (1.5 s round trip delay plus margin). 78 In general, any received pulse at a HomePNA station that does not conform to the pulse position requirements of AID symbols 0 through 7 shall indicate a collision on the wire. When a transmitting station senses a collision, it emits a JAM signal to alert all other stations to the collision. The following conditions signify a COLLISION event: 1. A HomePNA station receives an AID that does not match the one being sent. 2. A HomePNA station receives a pulse outside the AID_GUARD INTERVAL in AID intervals 0 to 7. 3. A HomePNA station receives a pulse inside the SILENT_INTERVAL (AID symbol 7). As in all cases, pulses received during a blanking interval are ignored. Passive stations (stations not actively transmitting during the collision) cannot reliably detect collisions. Therefore, once a collision is detected by a transmitting station, the station must inform the rest of the stations of the collision with a JAM pattern described below. Only a transmitting station emits a JAM signal. Once a collision is detected, the COLLISION signal to the MAC interface is asserted and is not reset until the MAC deactivates the TXEN signal. JAM Signal A JAM pattern consists of 1 pulse every 32 TICs and continues until at least the end of the AID intervals. After the AID interval, the JAM pattern will continue until TXEN from the MAC is deactivated. ACCESS ID Values The access ID values for slave stations are picked by each individual station randomly from the set of AID slave numbers described in the management section. During operation, each HomePNA station monitors HomePNA frames received on the wire. If it detects another HomePNA station using the same AID, it will select a new random AID. Silence Interval (AID symbol 7) The Access ID symbols are followed by a fixed silence interval of 129 TICs. The receive blanking interval is the same as that of the AID symbols (1 through 6). Any pulses detected in the silence interval are considered a COLLISION event for transmitting stations and are handled as described in the Collisions section. Am79C978 PULSE_POSITION_0 occurs at a value defined in Table 13 which determines the transmission speed. When a pulse begins transmission, the previous symbol interval ends and a new one begins immediately. Data Symbols Data symbols encode data for a much higher transmission rate, and they do not allow collision detection. Data Transmit Timing Table 13. A data symbol interval begins with the beginning of transmission of a pulse as shown in Figure 40. Transmit Symbol timing (in TICS) is measured from this point (TIC = 0). Depending on the data code, the next pulse may begin at any PULSE_POSITION_N where N = 0 to 24. Each position is separated from the previous one by one TIC. Blanking Interval Speed Settings Speed Setting Nominal Data Rate PULSE_POSITION_0 Value (in TICs) LOW_SPEED 0.7 Mbps 44 HIGH_SPEED 1.0 Mbps 28 Transmitter Symbol 1 Pulse 0 START_TX_PULSE TIC=0 Symbol 2 Data Blanking interval (DISBI) END_TX_PULSE time Pulse 1 PULSE_POSITION_0 time Position 1 1 TIC Position n1 n=0-24 Position 0 Position 1 Pulse 2 Position n2 22206B-44 Figure 40. Transmit Data Symbol Timing Data Receive Timing The incoming waveform is formed from the transmitted pulse. The receiver detects the point at which the envelope of the received waveform crosses a set threshold. See Figure 41. Immediately after the threshold crossing, the receiver disables any further detection for a period ISBI-3 TICs (HPR28 ISBI_SLOW or ISBI_FAST) starting with the detection of the pulse peak. The receiver is then re-enabled for pulse detection. Upon reception of the next pulse, the receiver measures the elapsed time from the previous pulse. This value is then placed in the nearest pulse position bin (one of 25) where pulse position 0 is at PULSE_POSITION_0 and each subsequent position is spaced one TIC from the previous one as defined in the Data Transmit Timing section. Data symbol intervals are therefore variable and depend on the encoded data. Receiver Symbol 1 Data slice threshold Symbol 2 Pulse 0 Pulse 1 Pulse 2 Detected Envelope END_DATA_BLANK Begin of receive Blanking interval Position 0 Position 1 Position n1 Position 0 Position 1 Position n2 22206B-45 Figure 41. Receive Symbol Timing Am79C978 79 3. If bit A is a zero, bit B is a zero, and bit C is a one, the next three bits (D, E, and F) select which one of the eight positions 17-24 is transmitted. The encoding process then continues at the root node. Data Symbol RLL25 Encoding The RLL25 code is the version of TM32 that was developed for the HomePNA PHY. It produces both the highest bit rate for a given value of ISBI and TIC size. In a manner similar to run length limited disk coding, RLL25 encodes data bits in groups of varying sizes, specifically: 3, 4, 5, and 6 bits. Pulse positions are assigned to the encoded bit groups in a manner, which causes more data bits to be encoded in positions that are farther apart. This keeps both the average and minimum bit rates higher. 4. Finally, if bits A, B, and C are all zeros, position 0 is transmitted. The encoding process then continues at the root node. As a result, Symbol 0 encodes the 3-bit data pattern 000, positions 1-8 encode the 4-bit data pattern 1BCD, positions 9-16 encode the 5-bit data pattern 01CDE, and positions 17-24 encode the 6-bit data pattern 001DEF. If the data encoded is random, 50% of the positions used will be for 4-bit patterns, 25% will be for 5bit patterns, 12.5% will be for 6-bit patterns, and 12.5% will be for 3-bit patterns. Data symbol RLL25 codes data by traversing a tree as illustrated in Figure 42. Assuming that successive data bits to be encoded are labeled A, B, C, D,..., etc. The encoding process begins at the root node and proceeds as follows: Management Interfaces 1. If the first bit (bit A) is a one, the next three bits (B, C, and D) select which one of the eight positions 18 is transmitted. The encoding process then continues at the root node. The HomePNA PHY may be managed from either of two interfaces (the managed parameters vary depending on the interface): 1. Remote Control-Word management commands embedded in the HomePNA AID header on the wire network. 2. If bit A is a zero and bit B is a one, the next three bits (C, D, and E) select which one of the eight positions 9-16 is transmitted. The encoding process then continues at the root node. 2. Management messages from a local management entity. Data stream from MAC controller Start: Examine the next bits to be encoded A Encoded and A=? 1 Send symbol 1-8 B=? D E F B C D These select position 1 - 8 1 Send symbol 9-16 0 0 C=? C Awaiting coding and transmission 1 0 B 1 C D E These select position 9 - 16 1 Send symbol 17-24 1 Send symbol 0 0 0 0 1 D E F These select position 17- 24 0 0 0 22206B-46 Figure 42. RLL 25 Coding Tree 80 Am79C978 Header AID Remote Control Word Commands Table 14. Master Station Control Word Functions Stations may be configured either as master stations or as slave stations. Only one master may exist on a given HomePNA segment. Aid No. 2. A slave is identified with an AID of 00h to EFh. 3. AID values of F0h to FEh are reserved for future use. Once a command has been transmitted, the master station will revert to a slave AID, so that subsequent control words are not interpreted as new commands. Master mode is entered by writing to the PHY control register (HPR16) and is exited upon the completion of the command sequence. A valid master remote command consists of three HomePNA frames with an AID of FFh. Since the HomePNA header is prepended to packets received from the MAC as well as Any1Home packets. Packets from the master station may be separated by intervals during which other (slave) stations may transmit their frames. A remote master Control Word command must be recognized and executed by a HomePNA PHY when it receives three consecutive valid HomePNA frames with an AID of FFh. If HPR16, bit 15 is not set to 0, valid commands are as follows: 1. SET_POWER: Commands slave stations to set their transmit level to a prescribed level. 2. SET_SPEED: Commands slave stations to set their transmit speed to a prescribed value. The control word bit encoding and possible values are described in Table 14. MSB Set to: 5 The master station may send commands embedded in the HomePNA header control word to remotely set various parameters of the remote slave stations. Stations are identified via the AID as follows: 1. The master station is identified on the HomePNA wire network with an AID of FFh. LSB Version 0 = Low Power 1 = High Power Set to: 6 0 = Low Speed Reserved 1 = High Speed All stations will transmit the following status messages in the HomePNA header control word of all outgoing frames: 1. VERSION_STATUS: The HomePNA PHY version of the slave station. 2. POWER_STATUS: The transmit power level of the transmitting slave station for the current frame. All HomePNA units support LOW_POWER and HIGH_POWER modes. 3. SPEED_STATUS: The transmit speed of the slave station for the current frame. Receiving stations will adjust their receiver parameters to correctly interpret this frame. The slave control word bit encoding and possible values are also described in Table 14. PHY Control and Management Block (PCM Block) Register Administration for 10BASE-T PHY Device The management interface specified in Clause 22 of the IEEE 802.3u standard provides for a simple two wire, serial interface to connect a management entity and a managed PHY for the purpose of controlling the PHY and gathering status information. The two lines are Management Data Input/Output (MDIO) and Management Data Clock (MDC). A station management entity which is attached to multiple PHY entities must have prior knowledge of the appropriate PHY address for each PHY entity. Description of the Methodology The management interface physically transports management information across the internal and external MII. The information is encapsulated in a frame format as specified in Clause 22 of the IEEE 802.3u draft standard and is shown in Table 15. Table 15. MII Control Frame Format PRE ST OP PHYAD REGAD TA DATA IDLE READ 1.1 01 10 AAAAA RRRRR Z0 D31.........D0 Z WRITE 1.1 01 01 AAAAA RRRRR 10 D31.........D0 Z Am79C978 81 The start field (ST) is followed by the operation field (OP). The operation field (OP) indicates whether the operation is a read or a write operation. This is followed by the PHY address (PHYAD) and the register address (REGAD) that was programed into BCR33 of the Fast Ethernet controller. This field is followed by a bus turnaround field (TA). During the read operation, the bus turnaround field is used to determine if the PHY is responding properly to the read request. The data field to/from the MAC controller is then written to or read from BCR34. The final field is the idle field, and it is required to allow the drivers to turn off. The PHYADD field, which is five bits wide, allows 32 unique PHY addresses. The managed PHY layer device that is connected to a station management entity via the MII interface has to respond to transactions addressed to the PHY's address. A station management entity attached to multiple PHYs is required to have prior knowledge of the appropriate PHY address. SRAM Configuration If the SRAM_SIZE (BCR25, bits 7-0) value is 0 in the SRAM size register, the controller will assume that there is no SRAM present and will reconfigure the four internal FIFOs into two FIFOs, one for transmit and one for receive. The FIFOs will operate the same as in the PCnet-PCI II controller. When the SRAM_SIZE (BCR25, bits 7-0) value is 0, the SRAM_BND (BCR26, bits 7-0) are ignored by the controller. See Figure 43. Low Latency Receive Configuration If the LOLATRX (BCR27, bit 4) bit is set to 1, then the controller will configure itself for a low latency receive configuration. In this mode, SRAM is required at all times. If the SRAM_SIZE (BCR25, bits 7-0) value is 0, the controller will not configure for low latency receive mode. The controller will provide a fast path on the receive side bypassing the SRAM. All transmit traffic will go to the SRAM, so SRAM_BND (BCR26, bits 7-0) has no meaning in low latency receive mode. When the controller has received 16 bytes from the network, it will start a DMA request to the PCI Bus Interface Unit. The controller will not wait for the first 64 bytes to pass to check for collisions in Low Latency Receive mode. The controller must be in STOP before switching to this mode. See Figure 44. CAUTION: To provide data integrity when switching into and out of the low latency mode, DO NOT SET the FASTSPNDE bit when setting the SPND bit. Receive frames WILL be overwritten and the controller may give erratic behavior when it is enabled again. Direct SRAM Access The SRAM can be accessed through the Expansion Bus Data port (BCR30). To access this data port, the user must load the upper address EPADDRU (BCR29, bits 3-0) and set FLASH (BCR29, bit 15) to 0. Then the user will load the lower 16 bits of address EPADDRL (BCR28, bits 15-0). To initiate a read, the user reads the Expansion Bus Data Port (BCR30). This slave access from the PCI will result in a retry for the very first access. Subsequent accesses may give a retry or not, depending on whether or not the data is present and valid. The direct SRAM access uses the same FLASH/ EPROM access except for accessing the SRAM in word format instead of byte format. This access is meant to be a diagnostic access only. The SRAM can only be accessed while the controller is in STOP or SPND (FASTSPNDE is set to 0) mode. . Bus Rcv FIFO MAC Rcv FIFO PCI Bus Interface Unit MAC Xmt FIFO Bus Xmt FIFO Buffer Management Unit 802.3 MAC Core and 10BASE-T and HomePNA PHYs FIFO Control 22206B-47 Figure 43. 82 Block Diagram SRAM Configuration Am79C978 Bus Rcv FIFO PCI Bus Interface Unit MAC Rcv FIFO Bus Xmt FIFO Buffer Management Unit 802.3 MAC Core SRAM MAC Xmt FIFO and 10BASE-T and HomePNA PHYs FIFO Control 22206B-48 Figure 44. Block Diagram Low Latency Receive Configuration Am79C978 83 EEPROM Interface The controller contains a built-in capability for reading and writing to an external serial 93C46 EEPROM. This built-in capability consists of an interface for direct connection to a 93C46 compatible EEPROM, an automatic EEPROM read feature, and a user-programmable register that allows direct access to the interface pins. Automatic EEPROM Read Operation Shortly after the deassertion of the RST pin, the controller will read the contents of the EEPROM that is attached to the interface. Because of this automatic-read capability of the controller, an EEPROM can be used to program many of the features of the controller at power-up, allowing system-dependent configuration information to be stored in the hardware instead of inside the device driver. If an EEPROM exists on the interface, the controller will read the EEPROM contents at the end of the H_RESET operation. The EEPROM contents will be serially shifted into a temporary register and then sent to various register locations on board the controller. Access to the Am79C978 configuration space or any I/O resource is not possible during the EEPROM read operation. The controller will terminate any access attempt with the assertion of DEVSEL and STOP while TRDY is not asserted, signaling to the initiator to disconnect and retry the access at a later time. A checksum verification is performed on the data that is read from the EEPROM. If the checksum verification passes, PVALID (BCR19, bit 15) will be set to 1. If the checksum verification of the EEPROM data fails, PVALID will be cleared to 0, and the controller will force all EEPROM-programmable BCR registers back to their H_RESET default values. However, the content of the Address PROM locations (offsets 0h - Fh from the I/O or memory mapped I/O base address) will not be cleared. The 8-bit checksum for the entire 82 bytes of the EEPROM should be FFh. If no EEPROM is present at the time of the automatic read operation, the controller will recognize this condition, abort the automatic read operation, and clear both the PREAD and PVALID bits in BCR19. All EEPROMprogrammable BCR registers will be assigned their default values after H_RESET. The content of the Address PROM locations (offsets 0h - Fh from the I/O or memory mapped I/O base address) will be undefined. EEPROM Auto-Detection The controller uses the EESK/LED1 pin to determine if an EEPROM is present in the system. At the rising edge of CLK during the last clock during which RST is asserted, the controller will sample the value of the EESK/LED1 pin. If the sampled value is a 1, then the controller assumes that an EEPROM is present, and the EEPROM read operation begins shortly after the 84 RST pin is deasserted. If the sampled value of EESK/ LED1 is a 0, the controller assumes that an external pull-down device is holding the EESK/LED1 pin low, indicating that there is no EEPROM in the system. Note that if the designer creates a system that contains an LED circuit on the EESK/LED1 pin, but has no EEPROM present, then the EEPROM auto-detection function will incorrectly conclude that an EEPROM is present in the system. However, this will not pose a problem for the controller, since the checksum verification will fail. Direct Access to the Interface The user may directly access the port through the EEPROM register, BCR19. This register contains bits that can be used to control the interface pins. By performing an appropriate sequence of accesses to BCR19, the user can effectively write to and read from the EEPROM. This feature may be used by a system configuration utility to program hardware configuration information into the EEPROM. EEPROM-Programmable Registers The following registers contain configuration information that will be programmed automatically during the EEPROM read operation: n I/O offsets 0h-Fh Address PROM locations n BCR2 Miscellaneous Configuration n BCR4 LED0 Status n BCR5 LED1 Status n BCR6 LED2 Status n BCR7 LED3 Status n BCR9 Full-Duplex Control n BCR18 Burst and Bus Control n BCR22 PCI Latency n BCR23 PCI Subsystem Vendor ID n BCR24 PCI Subsystem ID n BCR25 SRAM Size n BCR26 SRAM Boundary n BCR27 SRAM Interface Control n BCR32 PHY Control and Status n BCR33 PHY Address n BCR35 PCI Vendor ID n BCR36 PCI Power Management Capabilities (PMC) Alias Register n BCR37 PCI DATA Register 0 (DATA0) Alias Register n BCR38 PCI DATA Register 1 (DATA1) Alias Register n BCR39 PCI DATA Register 2 (DATA2) Alias Register Am79C978 n BCR40 PCI DATA Register 3 (DATA3) Alias Register n BCR41 PCI DATA Register 4 (DATA4) Alias Register n BCR42 PCI DATA Register 5 (DATA5) Alias Register n BCR43 PCI DATA Register 6 (DATA6) Alias Register n BCR44 PCI DATA Register 7 (DATA7) Alias Register n BCR45 OnNow Pattern Matching Register 1 n BCR46 OnNow Pattern Matching Register 2 n BCR47 OnNow Pattern Matching Register 3 n BCR48 LED4 Status There are two checksum locations within the EEPROM. The first checksum will be used by AMD driver software to verify that the ISO 8802-3 (IEEE/ANSI 802.3) station address has not been corrupted. The value of bytes 0Ch and 0Dh should match the sum of bytes 00h through 0Bh and 0Eh and 0Fh. The second checksum location (byte 51h) is not a checksum total, but is, instead, a checksum adjustment. The value of this byte should be such that the total checksum for the entire 82 bytes of EEPROM data equals the value FFh. The checksum adjust byte is needed by the controller in order to verify that the EEPROM content has not been corrupted. n BCR49 PHY Select LED Support n CRS12 Physical Address Register 0 n CRS13 Physical Address Register 1 n CRS14 Physical Address Register 2 The controller can support up to five LEDs. LED outputs LED0, LED1, LED2, LED3, and LED4 allow for direct connection of an LED and its supporting pull-up device. n CSR116 OnNow Miscellaneous If PREAD (BCR19, bit 14) and PVALID (BCR19, bit 15) are cleared to 0, then the EEPROM read has experienced a failure and the contents of the EEPROM programmable BCR register will be set to default H_RESET values. The content of the Address PROM locations, however, will not be cleared. EEPROM MAP The automatic EEPROM read operation will access 41 words (i.e., 82 bytes) of the EEPROM. The format of the EEPROM contents is shown in Table 16, beginning with the byte that resides at the lowest EEPROM address. Note: The first bit out of any word location in the EEPROM is treated as the MSB of the register being programmed. For example, the first bit out of EEPROM word location 09h will be written into BCR4, bit 15; the second bit out of EEPROM word location 09h will be written into BCR4, bit 14, etc. In applications that want to use the pin to drive an LED and also have an EEPROM, it might be necessary to buffer the LED3 circuit from the EEPROM connection. When an LED circuit is directly connected to the EEDO/LED3 pin, then it is not possible for most EEPROM devices to sink enough IOL to maintain a valid low level on the EEDO input to the controller. Use of buffering can be avoided if a low power LED is used. Each LED can be programmed through a BCR register to indicate one or more of the following network status or activities: Collision Status, Full-Duplex Link Status, Half-Duplex Link Status, Receive Match, Receive Status, Magic Packet, Disable Transceiver, Transmit Status, Power, and Speed. Am79C978 85 Table 16. EEPROM Map Word Address Byte Addr. 00h* 01h 01h 02h 03h 03h 05h 07h 04h 09h 05h 0Bh 06h 0Dh 07h 0Fh 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh 10h 11h 12h 13h 14h 15h 16h 17h 18h 19h 1Ah 1Bh 1Ch 1Dh 1Eh 1Fh 20h 21h 22h 23h 24h 25h 26h 27h 11h 13h 15h 17h 19h 1Bh 1Dh 1Fh 21h 23h 25h 27h 29h 2Bh 2Dh 2Fh 31h 33h 35h 37h 39h 3Bh 3Dh 3Fh 41h 43h 45h 47h 49h 4Bh 4Dh 4Fh 28h 51h 3Eh 3Fh 7Dh 7Fh Most Significant Byte 2nd byte of the ISO 8802-3 (IEEE/ANSI 802.3) station physical address for this node 00h Least Significant Byte First byte of the IS0 8802-3 (IEEE/ANSI 802.3) station physical address for this node, where "first byte" refers to the first byte to appear on the 802.3 medium 3rd byte of the node address 5th byte of the node address CSR116[7:0] (OnNow Misc. Configuration) 4th byte of the node address 02h 6th byte of the node address 04h CSR116[15:8] (OnNow Misc. Configuration) 06h Hardware ID: must be 11h if compatibility to 08h Reserved location: must be 00h AMD drivers is desired User programmable space 0Ah User programmable space MSB of two-byte checksum, which is the sum LSB of two-byte checksum, which is the sum 0Ch of bytes 00h-0Bh and bytes 0Eh and 0Fh of bytes 00h-0Bh and bytes 0Eh and 0Fh Must be ASCII "W" (57h) if compatibility to Must be ASCII "W" (57h) if compatibility to 0Eh AMD driver software is desired AMD driver software is desired BCR2[15:8] (Miscellaneous Configuration) 10h BCR2[7:0] (Miscellaneous Configuration) BCR4[15:8] (Link Status LED) 12h BCR4[7:0] (Link Status LED) BCR5[15:8] (LED1 Status) 14h BCR5[7:0] (LED1 Status) BCR6[15:8] (LED2 Status) 16h BCR6[7:0] (LED2 Status) BCR7[15:8] (LED3 Status) 18h BCR7[7:0] (LED3 Status) BCR9[15:8] (Full-Duplex control) 1Ah BCR9[7:0] (Full-Duplex Control) BCR18[15:8] (Burst and Bus Control) 1Ch BCR18[7:0] (Burst and Bus Control) BCR22[15:8] (PCI Latency) 1Eh BCR22[7:0] (PCI Latency) BCR23[15:8] (PCI Subsystem Vendor ID) 20h BCR23[7:0] (PCI Subsystem Vendor ID) BCR24[15:8] (PCI Subsystem ID) 22h BCR24[7:0] (PCI Subsystem ID) BCR25[15:8] (SRAM Size) 24h BCR25[7:0] (SRAM Size) BCR26[15:8] (SRAM Boundary) 26h BCR26[7:0] (SRAM Boundary) BCR27[15:8] (SRAM Interface Control) 28h BCR27[7:0] (SRAM Interface Control) BCR32[15:8] (MII Control and Status) 2Ah BCR32[7:0] (MII Control and Status) BCR33[15:8] (MII Address) 2Ch BCR33[7:0] (MII Address) BCR35[15:8] (PCI Vendor ID) 2Eh BCR35[7:0] (PCI Vendor ID) BCR36[15:8] (Conf. Space. byte 43h alias) 30h BCR36[7:0] (Conf. Space byte 42h alias) BCR37[15:8] (DATA_SCALE alias 0) 32h BCR37[7:0] (Conf. Space byte 47h0alias) BCR38[15:8] (DATA_SCALE alias 1) 34h BCR38[7:0] (Conf. Space byte 47h1alias) BCR39[15:8] (DATA_SCALE alias 2) 36h BCR39[7:0] (Conf. Space byte 47h2alias) BCR40[15:8] (DATA_SCALE alias 3) 38h BCR40[7:0] (Conf. Space byte 47h3alias) BCR41[15:8] (DATA_SCALE alias 4) 3Ah BCR41[7:0] (Conf. Space byte 47h4alias) BCR42[15:8] (DATA_SCALE alias 0) 3Ch BCR42[7:0] (Conf. Space byte 47h5alias) BCR43[15:8] (DATA_SCALE alias 0) 3Eh BCR43[7:0] (Conf. Space byte 47h6alias) BCR44[15:8] (DATA_SCALE alias 0) 40h BCR44[7:0] (Conf. Space byte 47h7alias) BCR48[15:8] (LED4 Status) 42h BCR48[7:0] (LED4 Status) BCR49[15:8] (PHY Select) 44h BCR49[7:0] (PHY Select) BCR50[15:8]Reserved location: must be 00h 46h BCR50[7:0]Reserved location: must be 00h BCR51[15:8]Reserved location: must be 00h 48h BCR51[7:0]Reserved location: must be 00h BCR52[15:8]Reserved location: must be 00h 4Ah BCR52[7:0]Reserved location: must be 00h BCR53[15:8]Reserved location: must be 00h 4Ch BCR53[7:0]Reserved location: must be 00h BCR54[15:8]Reserved location: must be 00h 4Eh BCR54[7:0]Reserved location: must be 00h Checksum adjust byte for the 82 bytes of the EEPROM contents, checksum of the 82 bytes 50h BCR54[7:0]Reserved location: must be 00h of the EEPROM should total to FFh Empty locations - Ignored by device Reserved Reserved 7Ch 7Eh Note: *Lowest EEPROM address. 86 Byte Addr. Am79C978 Reserved Reserved The LED pins can be configured to operate in either open-drain mode (active low) or in totem-pole mode (active high). The output can be stretched to allow the human eye to recognize even short events that last only several microseconds. After H_RESET, the five LED outputs are configured as shown in Table 17. COL COLE FDLS FDLSE LNKS LNKSE RCV RCVE Table 17. LED Default Configuration To Pulse Stretcher RCVM RCVME LED Output Indication Driver Mode Pulse Stretch LED0 Link Status Open Drain Active Low Enabled MR_SPEED_SEL 100E LED1 Receive Status Open Drain Active Low Enabled MPS MPSE LED2 Power Open Drain Active Low Enabled POWER POWERE LED3 Transmit Status Open Drain Active Low Enabled LED4 Speed Open Drain Active Low Enabled XMT XMTE Figure 45. 22206B-49 LED Control Logic The Am79C978 device supports three types of wakeup events: For each LED register, each of the status signals is AND'd with its enable signal, and these signals are all OR'd together to form a combined status signal. Each LED pin combined status signal can be programmed to run to a pulse stretcher, which consists of a 3-bit shift register clocked at 38 Hz (26 ms). The data input of each shift register is normally at logic 0. The OR gate output for each LED register asynchronously sets all three bits of its shift register when the output becomes asserted. The inverted output of each shift register is used to control an LED pin. Thus, the pulse stretcher provides 2 to 3 clocks of stretched LED output, or 52 ms to 78 ms. See Figure 45. Power Savings Mode Power Management Support The controller supports power management as defined in the PCI Bus Power Management Interface Specification V1.1 and Network Device Class Power Management Reference Specification V1.0a.These specifications define the network device power states, PCI power management interface including the Capabilities Data Structure and power management registers block definitions, power management events, and OnNow network wake-up events. The general scheme for the Am79C978 power management is that when a PCI wake-up event is detected, a signal is generated to cause hardware external to the Am79C978 device to put the computer into the working (S0) mode. 1. Magic Packet Detect 2. OnNow Pattern Match Detect 3. Link State Change Figure 46 shows the relationship between these wakeup events and the various outputs used to signal to the external hardware. OnNow Wake-Up Sequence The system software enables the PME pin by setting the PME_EN bit in the PMCSR register (PCI configuration registers, offset 44h, bit 8) to 1. When a wake-up event is detected, the controller sets the PME_STATUS bit in the PMCSR register (PCI configuration registers, offset 44h, bit 15). Setting this bit causes the PME signal to be asserted. Assertion of the PME signal causes external hardware to wake up the CPU. The system software then reads the PMCSR register of every PCI device in the system to determine which device asserted the PME signal. When the software determines that the signal came from the controller, it writes to the device's PMCSR to put the device into power state D0. The software then writes a 0 to the PME_STATUS bit to clear the bit and turn off the PME signal, and it calls the device's software driver to tell it that the device is now in state D0. The system software can clear the PME_STATUS bit either before, after, or at the same time that it puts the device back into the D0 state. Am79C978 87 Magic Packet MPPEN PG MPMAT S SET Q MPMODE MPEN R CLR Q POR MPDETECT Link Change LCMODE S SET Q LCDET S SET Q Link Change R CLR Q H_RESET R CLR Q POR PME_STATUS S DET Q Pattern Match POR BCR47 Input Pattern BCR46 BCR45 S SET Q Pattern Match RAM (PMR) R CLR Q PMAT R CLR Q POR PME Status PME_EN MPMAT PME PME_EN_OVR LCEVENT 22206B-50 Figure 46. OnNow Functional Diagram Link Change Detect Link change detect is one of wake-up events defined by the OnNow specification. Link Change Detect mode is set when the LCMODE bit (CSR116, bit 8) is set either by software or loaded through the EEPROM. When this bit is set, any change in the Link status will cause the LCDET bit (CSR116, bit 9) to be set. When the LCDET bit is set, the PME_STATUS bit (PMCSR register, bit 15) will be set. If either the PME_EN bit (PMCSR, bit 8) or the PME_EN_OVR bit (CSR116, bit 10) are set, then the PME will also be asserted. OnNow Pattern Match Mode In the OnNow Pattern Match Mode, the Am79C978 device compares the incoming packets with up to eight patterns stored in the Pattern Match RAM (PMR). The stored patterns can be compared with part or all of in- 88 coming packets, depending on the pattern length and the way the PMR is programmed. When a pattern match has been detected, then PMAT bit (CSR116, bit 7) is set. The setting of the PMAT bit causes the PME_STATUS bit (PMCSR, bit 15) to be set, which in turn will assert the PME pin if the PME_EN bit (PMCSR, bit 8) is set. Pattern Match RAM (PMR) PMR is organized as an array of 64 words by 40 bits as shown in Figure 47. The PMR is programmed indirectly through BCRs 45, 46, and 47. When BCR45 is written and the PMAT_MODE bit (BCR45, bit 7) is set to 1, Pattern Match logic is enabled. No bus accesses into the PMR are possible when the PMAT_MODE bit is set, and BCR46, BCR47, and all other bits in BCR45 are ignored. When PMAT_MODE is set, a read of BCR45 returns all bits undefined except for Am79C978 PMAT_MODE. In order to access the contents of the PMR, PMAT_MODE bit should be programmed to 0. When BCR45 is written to set the PMAT_MODE bit to 0, the Pattern Match logic is disabled and accesses to the PMR are possible. Bits 6:0 of BCR45 specify the address of the PMR word to be accessed. Writing to BCR45 does not immediately affect the contents of the PMR. Following the write to BCR45, the PMR word addressed by bits 6:0 of BCR45 may be read by reading BCR45, BCR46, and BCR47 in any order. To write to the PMR word, the write to BCR45 must be followed by a write to BCR46 and a write to BCR47 in that order to complete the operation. The PMR will not actually be written until the write to BCR47 is complete. The first two 40-bit words in this RAM serve as pointers and contain enable bits for the eight possible match patterns. The remainder of the RAM contains the match patterns and associated match pattern control bits. Byte 0 of the first word contains the pattern enable bits. Any bit position set in this byte enables the corresponding match pattern in the PMR, as an example if the bit 3 is set, then pattern 3 is enabled for matching. Bytes 1 to 4 in the first word are pointers to the beginning of the patterns 0 to 3, and bytes 1 to 4 in the second word are pointers to the beginning of patterns 4 to 7, respectively. Byte 0 of the second word has no function associated with it. Byte 0 of the words 2 to 63 is the control field of the PMR. Bit 7 of this field is the End of Packet (EOP) bit. When this bit is set, it indicates the end of a pattern in the PMR. Bits 6-4 of the control field byte are the SKIP bits. The value of the SKIP field indicates the number of the Dwords to be skipped before the pattern in this PMR word is compared with data from the incoming frame. A maximum of seven Dwords may be skipped. Bits 3-0 of the control field byte are the MASK bits. These bits correspond to the pattern match bytes 3-0 of the same PMR word (PMR bytes 4-1). If bit n of this field is 0, then byte n of the corresponding pattern word is ignored. If this field is programmed to 3, then bytes 0 and 1 of the pattern match field (bytes 2 and 1 of the word) are used, and bytes 3 and 2 are ignored in the pattern matching operation. The contents of the PMR ar e not affected by H_RESET, S_RESET, or STOP. The contents are undefined after a power up reset (POR). Magic Packet Mode In Magic Packet mode, the controller remains fully powered up (all VDD and VDDB pins must remain at their supply levels). The device will not generate any bus master transfers. No transmit operations will be initiated on the network. The device will continue to receive frames from the network, but all frames will be automatically flushed from the receive FIFO. Slave accesses to the controller are still possible. A Magic Packet is a frame that is addressed to the controller and contains a data sequence anywhere in its data field made up of 16 consecutive copies of the device's physical address (PADR[47:0]). The controller will search incoming frames until it finds a Magic Packet frame. It starts scanning for the sequence after processing the length field of the frame. The data sequence can begin anywhere in the data field of the frame, but must be detected before the controller reaches the frame's FCS field. Any deviation of the incoming frame's data sequence from the required physical address sequence, even by a single bit, will prevent the detection of that frame as a Magic Packet frame. The controller supports two different modes of address detection for a Magic Packet frame. If MPPLBA (CSR5, bit 5) or EMPPLBA (CSR116, bit 6) are at their default value of 0, the controller will only detect a Magic Packet frame if the destination address of the packet matches the content of the physical address register (PADR). If MPPLBA or EMPPLBA are set to 1, the destination address of the Magic Packet frame can be unicast, multicast, or broadcast. Note: The setting of MPPLBA or EMPPLBA only effects the address detection of the Magic Packet frame. The Magic Packet's data sequence must be made up of 16 consecutive copies of the device's physical address (PADR[47:0]), regardless of what kind of destination address it has. There are two general methods to place the controller into Magic Packet mode. The first is the software method. In this method, either the BIOS or other software sets the MPMODE bit (CSR5, bit 1). Then the controller must be put into suspend mode (see description of CSR5, bit 0), allowing any current network activity to finish. Finally, either PG must be deasserted (hardware control), or MPEN (CSR5, bit 2) must be set to 1 (software control). Note: FASTSPNDE (CSR7, bit 15) has no meaning in Magic Packet mode. The second method is the hardware method. In this method, the MPPEN bit (CSR116, bit 4) is set at power up by the loading of the EEPROM. This bit can also be set by software. The controller will be placed in the Magic Packet Mode when either the PG input is deasserted or the MPEN bit is set. Magic Packet mode can be disabled at any time by asserting PG or clearing MPEN bit. Am79C978 89 BCR 47 BCR Bit Number 15 8 7 PMR_B4 Pattern Match RAM Address BCR 46 0 15 8 PMR_B3 PMR_B2 BCR 45 7 0 15 PMR_B1 8 PMR_B0 Pattern Match RAM Bit Number 39 32 31 24 23 16 15 8 7 0 Comments 0 P3 pointer P2 pointer P1 pointer P0 pointer Pattern Enable bits First Address 1 P7 pointer P6 pointer P5 pointer P4 pointer X Second Address 2 Data Byte 3 Data Byte 2 Data Byte1 Data Byte 0 Pattern Control Start Pattern P1 2+n Data Byte 4n+3 Date Byte 4n+2 Data Byte 4n+1 Data Byte 4n+0 J Data Byte 3 Data Byte 2 Data Byte 1 Data Byte 0 J+m Data Byte 4m+3 Data Byte 4m+2 Data Byte 4m+1 Data Byte 4m+0 Pattern Control End Pattern P1 Pattern Control Start Pattern Pk Pattern Control End Pattern Pk 63 Last Address 7 EOP 6 5 4 SKIP 3 2 1 0 MASK 22206B-51 Figure 47. Pattern Match RAM When the controller detects a Magic Packet frame, it sets the MPMAT bit (CSR116, bit 5), the MPINT bit (CSR5, bit 4), and the PME_STATUS bit (PMCSR, bit 15). If the PME_EN or the PME_EN_OVR bits are set, the PME will be asserted as well. If IENA (CSR0, bit 6) and MPINTE (CSR5, bit 3) are set to 1, INTA will be asserted. Any one of the four LED pins can be programmed to indicate that a Magic Packet frame has been received. MPSE (BCR4-7, bit 9) must be set to 1 to enable that function. Note: The polarity of the LED pin can be programmed to be active HIGH by setting LEDPOL (BCR4-7, bit 14) to 1. Once a Magic Packet frame is detected, the controller will discard the frame internally, but will not resume nor- 90 mal transmit and receive operations until PG is asserted or MPEN is cleared. Once both of these events has occurred, indicating that the system has detected the Magic Packet and is awake, the controller will continue polling receive and transmit descriptor rings where it left off. It is not necessary to re-initialize the device. If the part is re-initialized, then the descriptor locations will be reset and the controller will not start where it left off. If magic packet mode is disabled by the assertion of PG, then in order to immediately re-enable Magic Packet mode, the PG pin must remain deasserted for at least 200 ns before it is reasserted. If Magic Packet mode is disabled by clearing MPEN bit, then it may be immediately re-enabled by setting MPEN back to 1. Am79C978 The PCI bus interface clock (CLK) is not required to be running while the device is operating in Magic Packet mode. Either of the INTA, the LED pins, or the PME signal may be used to indicate the receipt of a Magic Packet frame when the CLK is stopped. If the system wishes to stop the CLK, it will do so after enabling the Magic Packet mode. CAUTION: To prevent unwanted interrupts from other active parts of the controller, care must be taken to mask all likely interruptible events during Magic Packet mode. An example would be the interrupts from the Media Independent Interface, which could occur while the device is in Magic Packet mode. IEEE 1149.1 (1990) Test Access Port Interface An IEEE 1149.1-compatible boundary scan Test Access Port is provided for board-level continuity test and diagnostics. All digital input, output, and input/output pins are tested. The following paragraphs summarize the IEEE 1149.1-compatible test functions implemented in the controller. Boundary Scan Circuit Table 18. IEEE 1149.1 Supported Instruction Summary Mode Selected Data Register Test BSR Normal ID REG Normal BSR Force Float Normal Bypass 0100 Control Boundary to I/0 Test Bypass 1111 Bypass Scan Normal Instruction Instruction Description Name Code EXTEST 0000 IDCODE 0001 SAMPLE 0010 TRIBYP 0011 SETBYP BYPASS External Test ID Code Inspection Sample Boundary Bypass Instruction Register and Decoding Logic After the TAP FSM is reset, the IDCODE instruction is always invoked. The decoding logic gives signals to control the data flow in the data registers according to the current instruction. Boundary Scan Register The boundary scan test circuit requires four pins (TCK, TMS, TDI, and TDO), defined as the Test Access Port (TAP). It includes a finite state machine (FSM), an instruction register, a data register array, and a power-on reset circuit. Internal pull-up resistors are provided for the TDI, TCK, and TMS pins. Each Boundary Scan Register (BSR) cell has two stages. A flip-flop and a latch are used for the Serial Shift Stage and the Parallel Output Stage, respectively. There are four possible operation modes in the BSR cell shown in Table 19. TAP Finite State Machine The TAP engine is a 16-state finite state machine (FSM), driven by the Test Clock (TCK), and the Test Mode Select (TMS) pins. An independent power-on reset circuit is provided to ensure that the FSM is in the TEST_LOGIC_RESET state at power-up. Therefore, the TRST is not provided. The FSM is also reset when TMS and TDI are high for five TCK periods. Table 19. BSR Mode Of Operation 1 2 3 4 Capture Shift Update System Function Other Data Registers Other data registers are the following: Supported Instructions In addition to the minimum IEEE 1149.1 requirements (BYPASS, EXTEST, and SAMPLE instructions), three additional instructions (IDCODE, TRIBYP, and SETBYP) are provided to further ease board-level testing. All unused instruction codes are reserved. See Table 18 for a summary of supported instructions. 1. Bypass register (1 bit) 2. Device ID register (32 bits) (Table 20). Table 20. Device ID Register Bits 31-28 Version Bits 27-12 Part Number (0010 0110 0010 0110) Bits 11-1 Manufacturer ID. The 11 bit manufacturer ID cod for AMD is 00000000001 in accordance with JEDEC publication 106-A. Bit 0 Always a logic 1 Note: The content of the Device ID register is the same as the content of CSR88. Am79C978 91 NAND Tree Testing The controller provides a NAND tree test mode to allow checking connectivity to the device on a printed circuit board. The NAND tree is built on all PCI bus pins. NAND tree testing is enabled by asserting RST. PG input should be driven HIGH during NAND tree testing. All PCI bus signals will become inputs on the assertion of RST. The result of the NAND tree test can be observed on the INTA pin. See Figure 48. Pin 141 (RST) is the first input to the NAND tree. Pin 142 (CLK) is the second input to the NAND tree, followed by pin 143 (GNT). All other PCI bus signals follow, counterclockwise, with pin 61 (AD0) being the last. Table 21 and Table 22 shows the complete list of pins connected to the NAND tree. RST must be asserted low to start a NAND tree test sequence. Initially, all NAND tree inputs except RST should be driven high. This will result in a high output at the INTA pin. If the NAND tree inputs are driven from high to low in the same order as they are connected to build the NAND tree, INTA will toggle every time an additional input is driven low. INTA will change to low, when CLK is driven low and all other NAND tree inputs stay high. INTA will toggle back to high, when GNT is additionally driven low. The square wave will continue until all NAND tree inputs are driven low. INTA will be high, when all NAND tree inputs are driven low. See Figure 49. Some of the pins connected to the NAND tree are outputs in normal mode of operation. They must not be driven from an external source until the controller is configured for NAND tree testing. VDD RST (pin141) Am79C978 Core CLK (pin 142) Am79C972 Core GNT (pin 143) .... INTA B S O INTA (pin 140) A MUX AD0 (pin 61) 22206B-52 Figure 48. NAND Tree Circuitry (160 PQFP) 92 Am79C978 Table 21. NAND Tree Input No. Pin No. NAND Tree Pin Sequence (160 PQFP) NAND Tree Input No. Pin No. Name Name NAND Tree Input No. Pin No. Name 1 141 RST 18 9 AD20 35 36 AD13 2 142 PCI_CLK 19 11 AD19 36 38 AD12 3 143 GNT 20 12 AD18 37 43 AD11 4 144 REQ 21 14 AD17 38 45 AD10 5 146 AD31 22 16 AD16 39 46 AD9 6 149 AD30 23 17 C/BE2 40 47 AD8 7 150 AD29 24 19 FRAME 41 48 C/BE0 8 151 AD28 25 20 IRDY 42 50 AD7 9 152 AD27 26 22 TRDY 43 52 AD6 10 154 AD26 27 24 DEVSEL 44 53 AD5 11 156 AD25 28 25 STOP 45 55 AD4 12 157 AD24 29 27 PERR 46 56 AD3 13 158 C/BE3 30 28 SERR 47 58 AD2 14 3 IDSEL 31 30 PAR 48 60 AD1 15 4 AD23 32 32 C/BE1 49 61 AD0 16 6 AD22 33 33 AD15 50 17 8 AD21 34 35 AD14 51 Pin No. Name Table 22. NAND Tree Pin Sequence (144 TQFP) NAND Tree Input No. Pin No. Name NAND Tree Input No. Pin No. Name NAND Tree Input No. 1 127 RST 18 7 AD20 35 34 AD13 2 128 PCI_CLK 19 9 AD19 36 36 AD12 3 129 GNT 20 10 AD18 37 37 AD11 4 130 REQ 21 12 AD17 38 39 AD10 5 132 AD31 22 14 AD16 39 40 AD9 6 135 AD30 23 15 C/BE2 40 41 AD8 7 136 AD29 24 17 FRAME 41 42 C/BE0 8 137 AD28 25 18 IRDY 42 44 AD7 9 138 AD27 26 20 TRDY 43 46 AD6 10 140 AD26 27 22 DEVSEL 44 47 AD5 11 142 AD25 28 23 STOP 45 49 AD4 12 143 AD24 29 25 PERR 46 50 AD3 13 144 C/BE3 30 26 SERR 47 52 AD2 14 1 IDSEL 31 28 PAR 48 54 AD1 15 2 AD23 32 30 C/BE1 49 55 AD0 16 4 AD22 33 31 AD15 17 6 AD21 34 33 AD14 Am79C978 93 RST CLK GNT REQ AD[31:0] C/BE[3:0] 0000FFFF FFFFFFFF F 3 7 1 IDSEL FRAME IRDY TRDY DEVSEL STOP PERR SERR PAR ... ... ... INTA 22206B-53 Figure 49. NAND Tree Waveform Reset There are four different types of RESET operations that may b e perfo rme d on the Am7 9C978 dev ic e, H_RESET, S_RESET, STOP, and POR. The following is a description of each type of RESET operation. H_RESET Hardware Reset (H_RESET) is an Am79C978 reset operation that has been created by the proper assertion of the RST pin of the Am79C978 device while the PG pin is HIGH. When the minimum pulse width timing as specified in the RST pin description has been satisfied, an internal reset operation will be performed. H_RESET will program most of the CSR and BCR registers to their default value. Note that there are several CSR and BCR registers that are undefined after H_RESET. See the sections on the individual registers for details. H_RESET will clear most of the registers in the PCI configuration space. H_RESET will cause the microcode program to jump to its reset state. Following the end of the H_RESET operation, the controller will attempt to read the EEPROM device through the EEPROM interface. H_RESET will clear DWIO (BCR18, bit 7) and the controller will be in 16-bit I/O mode after the reset operation. A DWord write operation to the RDP (I/O offset 94 10h) must be performed to set the device into 32-bit I/O mode. S_RESET Software Reset (S_RESET) is an Am79C978 reset operation that has been created by a read access to the Reset register, which is located at offset 14h in Word I/O mode or offset 18h in DWord I/O mode from the Am79C978 I/O or memory mapped I/O base address. S_RESET will reset all of or some portions of CSR0, 3, 4, 15, 80, 100, and 124 to default values. For the identity of individual CSRs and bit locations that are affected by S_RESET, see the individual CSR register descriptions. S_RESET will not affect any PCI configuration space location. S_RESET will not affect any of the BCR register values. S_RESET will cause the microcode program to jump to its reset state. Following the end of the S_RESET operation, the controller will not attempt to read the EEPROM device. After S_RESET, the host must perform a full re-initialization of the controller before starting network activity. S_RESET will cause REQ to deassert immediately. STOP (CSR0, bit 2) or SPND (CSR5, bit 0) can be used to terminate any pending bus mastership request in an orderly sequence. S_RESET terminates all network activity abruptly. The host can use the suspend mode (SPND, CSR5, bit 0) to terminate all network activity in an orderly sequence before issuing an S_RESET. Am79C978 STOP A STOP reset is generated by the assertion of the STOP bit in CSR0. Writing a 1 to the STOP bit of CSR0, when the stop bit currently has a value of 0, will initiate a STOP reset. If the STOP bit is already a 1, then writing a 1 to the STOP bit will not generate a STOP reset. STOP will reset all or some portions of CSR0, 3, and 4 to default values. For the identity of individual CSRs and bit locations that are affected by STOP, see the individual CSR register descriptions. STOP will not affect any of the BCR and PCI configuration space locations. STOP will cause the microcode program to jump to its reset state. Following the end of the STOP operation, the controller will not attempt to read the EEPROM device. Note: STOP will not cause a deassertion of the REQ signal, if it happens to be active at the time of the write to CSR0. The controller will wait until it gains bus ownership, and it will first finish all scheduled bus master accesses before the STOP reset is executed. STOP terminates all network activity abruptly. The host can use the suspend mode (SPND, CSR5, bit 0) to ter- Table 24. 31 24 23 Device ID Status 16 minate all network activity in an orderly sequence before setting the STOP bit. Power on Reset Power on Reset (POR) is generated when the controller is powered up. POR generates a hardware reset (H_RESET). In addition, it clears some bits that H_RESET does not affect. Software Access PCI Configuration Registers The controller implements the 256-byte configuration space as defined by the PCI draft specification revision 2.2. The 64-byte header includes all registers required to identify the controller and its function. Additionally, PCI Power Management Interface registers are implemented at location 40h - 47h. The layout of the PCI configuration space is shown in Table 24. The PCI configuration registers are accessible only by configuration cycles. All multi-byte numeric fields follow little endian byte ordering. All write accesses to Reserved locations have no effect; reads from these locations will return a data value of 0. PCI Configuration Space Layout 15 8 7 0 Vendor ID Command Base-Class Sub-Class Programming IF Revision ID Reserved Header Type Latency Timer Reserved I/O Base Address Memory Mapped I/O Base Address Reserved Reserved Reserved Reserved Reserved Subsystem ID Subsystem Vendor ID Expansion ROM Base Address Reserved CAP-PTR Reserved MAX_LAT MIN_GNT Interrupt Pin Interrupt Line PMC NXT_ITM_PTR CAP_ID DATA_REG PMCSR_BSE PMCSR Reserved . FCh Reserved I/O Resources The Am79C978 controller requires 32 bytes of address space for access to all the various internal registers as well as to some setup information stored in an external serial EEPROM. A software reset port is available, too. Offset 00h 04h 08h 0Ch 10h 14h 18h 1Ch 20h 24h 28h 2Ch 30h 34h 38h 3Ch 40h 44H . The Am79C978 controller supports mapping the address space to both I/O and memory space. The value in the PCI I/O Base Address register determines the start address of the I/O address space. The register is typically programmed by the PCI configuration utility after system power-up. Am79C978 95 The PCI configuration utility must also set the IOEN bit in the PCI Command register to enable I/O accesses to the Am79C978 controller. For memory mapped I/O access, the PCI Memory Mapped I/O Base Address register controls the start address of the memory space. The MEMEN bit in the PCI Command register must also be set to enable the mode. Both base address registers can be active at the same time. The Am79C978 controller supports two modes for accessing the I/O resources. For backwards compatibility with AMD's 16-bit Ethernet controllers, Word I/O is the default mode after power up. The device can be configured to DWord I/O mode by software. I/O Registers The Am79C978 controller registers are divided into two groups. The Control and Status Registers (CSR) are used to configure the Ethernet MAC engine and to obtain status information. The Bus Control Registers (BCR) are used to configure the bus interface unit and the LEDs. Both sets of registers are accessed using indirect addressing. The CSR and BCR share a common Register Address Port (RAP). There are, however, separate data ports. The Register Data Port (RDP) is used to access a CSR. The BCR Data Port (BDP) is used to access a BCR. In order to access a particular CSR location, the RAP should first be written with the appropriate CSR address. The RDP will then point to the selected CSR. A read of the RDP will yield the selected CSR data. A write to the RDP will write to the selected CSR. In order to access a particular BCR location, the RAP should first be written with the appropriate BCR address. The BDP will then point to the selected BCR. A read of the BDP will yield the selected BCR data. A write to the BDP will write to the selected BCR. Once the RAP has been written with a value, the RAP value remains unchanged until another RAP write occurs, or until an H_RESET or S_RESET occurs. RAP is cleared to all 0s when an H_RESET or S_RESET occurs. RAP is unaffected by setting the STOP bit. Address PROM Space The Am79C978 controller allows for connection of a serial EEPROM. The first 16 bytes of the EEPROM will be automatically loaded into the Address PROM (APROM) space after H_RESET. Additionally, the first six bytes of the EEPROM will be loaded into CSR12 to CSR14. The Address PROM space is a convenient place to store the value of the 48-bit IEEE station address. It can be overwritten by the host computer, and its content has no effect on the operation of the Am79C978 controller. The software must copy the station address from the Address PROM space to the ini- 96 tialization block in order for the receiver to accept unicast frames directed to this station. The six bytes of the IEEE station address occupy the first six locations of the Address PROM space. The next six bytes are reserved. Bytes 12 and 13 should match the value of the checksum of bytes 1 through 11 and 14 and 15. Bytes 14 and 15 should each be ASCII "W" (57h). The above requirements must be met in order to be compatible with AMD driver software. APROMWE bit (BCR2, bit 8) must be set to 1 to enable write access to the Address PROM space. Reset Register A read of the Reset register creates an internal software reset (S_RESET) pulse in the Am79C978 controller. The internal S_RESET pulse that is generated by this access is different from both the assertion of the hardware RST pin (H_RESET) and from the assertion of the software STOP bit. Specifically, S_RESET is the equivalent of the assertion of the RST pin (H_RESET) except that S_RESET has no effect on the BCR or PCI Configuration space locations. The NE2100 LANCE-based family of Ethernet cards requires that a write access to the Reset register follows each read access to the Reset register. The Am79C978 controller does not have a similar requirement. The write access is not required and does not have any effect. Note: The Am79C978 controller cannot service any slave accesses for a very short time after a read access of the Reset register, because the internal S_RESET operation takes about 1 ms to finish. The Am79C978 controller will terminate all slave accesses with the assertion of DEVSEL and STOP while TRDY is not asserted, signaling to the initiator to disconnect and retry the access at a later time. Word I/O Mode After H_RESET, the Am79C978 controller is programmed to operate in Word I/O mode. DWIO (BCR18, bit 7) will be cleared to 0. Table 25 shows how the 32 bytes of address space are used in Word I/O mode. All I/O resources must be accessed in word quantities and on word addresses. The Address PROM locations can also be read in byte quantities. The only allowed DWord operation is a write access to the RDP, which switches the device to DWord I/O mode. A read access other than listed in the table below will yield undefined data; a write operation may cause unexpected reprogramming of the Am79C978 control registers. Table 26 shows legal I/O accesses in Word I/O mode. Am79C978 Table 25. I/O Map in Word I/O Mode (DWIO = 0) Offset No. of Bytes Register 00h - 0Fh 16 APROM 10h 2 RDP 12h 2 RAP (shared by RDP and BDP) 14h 2 Reset Register 16h 2 BDP 18h - 1Fh 8 Reserved Double Word I/O Mode The Am79C978 controller can be configured to operate in DWord (32-bit) I/O mode. The software can invoke the DWIO mode by performing a DWord write access to the I/O location at offset 10h (RDP). The data of the write access must be such that it does not affect the intended operation of the Am79C978 controller. Setting the device into 32-bit I/O mode is usually the first operation after H_RESET or S_RESET. The RAP register will point to CSR0 at that time. Writing a value of 0 to CSR0 is a safe operation. DWIO (BCR18, bit 7) will be set to 1 as an indication that the Am79C978 controller operates in 32-bit I/O mode. Note: Even though the I/O resource mapping changes when the I/O mode setting changes, the RDP location offset is the same for both modes. Once the DWIO bit has been set to 1, only H_RESET can clear it to 0. The DWIO mode setting is unaffected by S_RESET or setting of the STOP bit. Table 27 shows how the 32 bytes of address space are used in DWord I/O mode. All I/O resources must be accessed in DWord quantities and on DWord addresses. A read access other than listed in Table 27 will yield undefined data, a write operation may cause unexpected reprogramming of the Am79C978 control registers. Table 26. Legal I/O Accesses in Word I/O Mode (DWIO = 0) AD[4:0] BE[3:0] Type Comment 0XX00 1110 RD Byte read of APROM location 0h, 4h, 8h, or Ch 0XX01 1101 RD Byte read of APROM location 1h, 5h, 9h, or Dh 0XX10 1011 RD Byte read of APROM location 2h, 6h, Ah, or Eh 0XX11 0111 RD Byte read of APROM location 3h, 7h, Bh, or Fh 0XX00 1100 RD Word read of APROM locations 1h (MSB) and 0h (LSB), 5h and 4h, 8h and 9h, or Ch and Dh 0XX10 0011 RD Word read of APROM locations 3h (MSB) and 2h (LSB), 7h and 6h, Bh and Ah, or Fh and Eh 10000 1100 RD Word read of RDP 10010 0011 RD Word read of RAP 10100 1100 RD Word read of Reset Register 10110 0011 RD Word read of BDP 0XX00 1100 WR Word write to APROM locations 1h (MSB) and 0h (LSB), 5h and 4h, 8h and 9h, or Ch and Dh 0XX10 0011 WR Word write to APROM locations 3h (MSB) and 2h (LSB), 7h and 6h, Bh and Ah, or Fh and Eh 10000 1100 WR Word write to RDP 10010 0011 WR Word write to RAP 10100 1100 WR Word write to Reset Register 10110 0011 WR Word write to BDP 10000 0000 WR DWord write to RDP, switches device to DWord I/O mode Am79C978 97 Table 27. I/O Map in DWord I/O Mode (DWIO = 1) Offset No. of Bytes Register 00h - 0Fh 16 APROM 10h 4 RDP 14h 4 RAP (shared by RDP and BDP) 18h 4 Reset Register 1Ch 4 BDP Table 28. AD[4:0] Legal I/O Accesses in Double Word I/O Mode (DWIO =1) BE[3:0] Type Comment 0XX00 0000 RD DWord read of APROM locations 3h (MSB) to 0h (LSB), 7h to 4h, Bh to 8h, or Fh to Ch 10000 0000 RD DWord read of RDP 10100 0000 RD DWord read of RAP 11000 0000 RD DWord read of Reset Register WR DWord write to APROM locations 3h (MSB) to 0h (LSB), 7h to 4h, Bh to 8h, or Fh to Ch 0XX00 0000 10000 0000 WR DWord write to RDP 10100 0000 WR DWord write to RAP 11000 0000 WR DWord write to Reset Register IEEE 802.3, Section 14.3.1.2. The load is a twisted pair cable that meets IEEE 802.3, Section 14.4. The TX signal is filtered on the chip to reduce harmonic content per Section 14.3.2.1 (10BASE-T). Since filtering is performed in silicon, TX can be connected directly to a standard transformer. External filtering modules are not needed. Twisted Pair Receive Function The RX+ port is a differential twisted-pair receiver. When properly terminated, the RX+ port will meet the electrical requirements for 10BASE-T receivers as specified in IEEE 802.3, Section 14.3.1.3. The receiver has internal filtering and does not require external filter modules or common mode chokes. Signals appearing at the RX differential input pair are routed to the internal decoder. The receiver function meets the propagation delays and jitter requirements specified by the 10BASE-T standard. The receiver squelch level drops to half its threshold value after unsquelch to allow reception of minimum amplitude signals and to mitigate carrier fade in the event of worst case signal attenuation and crosstalk noise conditions. Clock Data Manchester Encoder Clock Data Manchester Decoder 10BASE-T Physical Layer Squelch Circuit The 10BASE-T block consists of the following subblocks: -- Transmit Process -- Receive Process TX Driver RX Driver TX RX -- Interface Status -- Collision Detect Function -- Jabber Function -- Reverse Polarity Detect Refer to Figure 50 for the 10BASE-T block diagram. 22206B-54 Figure 50. 10BASE-T Transmit and Receive Data Paths Twisted Pair Transmit Function Data transmission over the 10BASE-T medium requires use of the integrated 10BASE-T MAU and uses the differential driver circuitry on the TX pins. TX is a differential twisted-pair driver. When properly terminated, TX will meet the transmitter electrical requirements for 10BASE-T transmitters as specified in 98 Twisted Pair Interface Status The Am79C978 device will power up in the Link Fail state. The Auto-Negotiation algorithm will apply to allow it to enter the Link Pass state. Am79C978 In the Link Pass state, receive activity which passes the pulse width/amplitude requirements of the RX inputs will cause the PCS Control block to assert Carrier Sense (CRS) signal at the internal MII interface. A collision would cause the PCS Control block to assert Carrier Sense (CRS) and Collision (COL) signals at the internal MII. In the Link Fail state, this block would cause the PCS Control block to de-assert Carrier Sense (CRS) and Collision (COL). In jabber detect mode, this block would cause the PCS Control block to assert the COL signal at the internal MII and allow the PCS Control block to assert or de-assert the CRS pin to indicate the current state of the RX pair. If there is no receive activity on RX, this block would cause the PCS Control block to assert only the COL pin at the internal MII. If there is RX activity, this block would cause the PCS Control block to assert both COL and CRS at the internal MII. Collision Detect Function Simultaneous activity (presence of valid data signals) from both the internal encoder transmit function and the twisted pair RX pins constitutes a collision, thereby causing the PCS Control block to assert the COL pin at the internal MII. Jabber Function The Jabber function inhibits the 10BASE-T twisted pair transmit function of the Am79C978 device if the TX circuits are active for an excessive period (20-150 ms). This prevents one port from disrupting the network due to a stuck-on or faulty transmitter condition. If the maximum transmit time is exceeded, the data path through the 10BASE-T transmitter circuitry is disabled (although Link Test pulses will continue to be sent). The PCS Control block also asserts the COL signal at the internal MII and sets the Jabber Detect bit in Register 1 of the active PHY. Once the internal transmit data stream from the Manchester Encoder/Decoder stops, an unjab time of 250-750 ms will elapse before this block causes the PCS Control block to de-assert the COL indication and re-enable the transmit circuitry. When jabber is detected, this block will cause the PCS Control block to assert the COL signal and allow the PCS Control block to assert or de-assert the CRS signal to indicate the current state of the RX pair. If there is no receive activity on RX, this block causes the PCS Control block to assert only the COL signal at the internal MII. If there is RX activity, this block will cause the PCS Control block to assert both COL and CRS on the internal MII. Reverse Polarity Detect nored, but it will set the polarity to the correct state. The reception of two consecutive packets will cause the polarity to be locked, based on the polarity of the ETD. In order to change the polarity once it has been locked, the link must be brought down and back up again. Auto-Negotiation The object of the Auto-Negotiation function is to determine the abilities of the devices sharing a link. After exchanging abilities, the Am79C978 device and remote link partner device acknowledge each other and make a choice of which advertised abilities to support. The Auto-Negotiation function facilitates an ordered resolution between exchanged abilities. This exchange allows both devices at either end of the link to take maximum advantage of their respective shared abilities. The Am79C978 device implements the transmit and receive Auto-Negotiation algorithm as defined in IEEE 802.3u, Section 28. The Auto-Negotiation algorithm uses a burst of link pulses called Fast Link Pulses (FLPs). The burst of link pulses are spaced between 55 and 140 s so as to be ignored by the standard 10BASE-T algorithm. The FLP burst conveys information about the abilities of the sending device. The receiver can accept and decode an FLP burst to learn the abilities of the sending device. The link pulses transmitted conform to the standard 10BASE-T template. The device can perform auto-negotiation with reverse polarity link pulses. The Am79C978 device uses the Auto-Negotiation algorithm to select the type connection to be established according to the following priority: 10BASE-T full duplex, then 10BASE-T half-duplex. See Table 29. The Auto-Negotiation algorithm is initiated by the following events: Auto-Negotiation enable bit is set, hardware reset, soft reset, transition to link fail state (when Auto-Negotiation enable bit is set), or Auto-Negotiation restart bit is set. The result of the Auto-Negotiation process can be read from the status register (Summary Status Register, TBR24). By default, the link partner must be at least 10BASE-T half-duplex capable. The Am79C978 controller can automatically negotiate with the network and yield the highest performance possible without software support. See the Network Port Manager section for more details. Table 29. Auto-Negotiation Capabilities Network Speed 20 Mbps 10 Mbps Physical Network Type 10BASE-T, Full Duplex 10BASE-T, Half Duplex The polarity for 10BASE-T signals is set by reception of Normal Link Pulses (NLP) or packets. Polarity is locked, however, by incoming packets only. The first NLP received when trying to bring the link up will be ig- Am79C978 99 Auto-Negotiation goes further by providing a messagebased communication scheme called Next Pages before connecting to the Link Partner. This feature is not supported in the Am79C978 device unless the DANAS (BCR32, bit 10) is selected. Soft Reset Function The PHY Control Register (TBR0) incorporates the soft reset function (bit 15). It is a read/write register and is self-clearing. Writing a 1 to this bit causes a soft reset. When read, the register returns a 1 if the soft reset is still being performed; otherwise, it is cleared to 0. Note 100 that the register can be polled to verify that the soft reset has terminated. Under normal operating conditions, soft reset will be finished in 150 clock cycles. Soft reset only resets the 10BASE-T PHY unit registers to default values (some register bits retain their previous values). Refer to the individual registers for values after a soft reset. Soft reset does not reset the management interface. Am79C978 USER ACCESSIBLE REGISTERS The Am79C978 controller has four types of user registers: the PCI configuration registers, the Control and Status registers (CSRs), the Bus Control registers (BCRs), 10BASE-T PHY Management registers (TBRs), and 1 Mbps HomePNA PHY Management registers (HPRs). The Am79C978 controller implements all PCnet-ISA (Am79C960) registers, all C-LANCE (Am79C90) registers, plus a number of additional registers. The Am79C978 CSRs are compatible upon power up with both the PCnet-ISA CSRs and all of the C-LANCE CSRs. The PCI configuration registers can be accessed in any data width. All other registers must be accessed according to the I/O mode that is currently selected. When WIO mode is selected, all other register locations are defined to be 16 bits in width. When DWIO mode is selected, all these register locations are defined to be 32 bits in width, with the upper 16 bits of most register locations marked as reserved locations with undefined values. When performing register write operations in DWIO mode, the upper 16 bits should always be written as zeros. When performing register read operations in DWIO mode, the upper 16 bits of I/O resources should always be regarded as having undefined values, except for CSR88. The following is a list of the registers that would typically need to be programmed once during the setup of the controller within a system. The control bits in each of these registers typically do not need to be modified once they have been written. However, there are no restrictions as to how many times these registers may actually be accessed. Note that if the default power up values of any of these registers is acceptable to the application, then such registers need never be accessed at all. Note: Registers marked with "^" may be programmable through the EEPROM read operation and, therefore, do not necessarily need to be written to by the system initialization procedure or by the driver software. Registers marked with "*" will be initialized by the initialization block read operation. CSR1 Initialization Block Address[15:0] CSR2* Initialization Block Address[31:16] CSR3 Interrupt Masks and Deferral Control CSR4 Test and Features Control CSR5 Extended Control and Interrupt CSR7 Extended Control and Interrupt2 CSR8* Logical Address Filter[15:0] CSR9* Logical Address Filter[31:16] The Am79C978 registers can be divided into four groups: PCI Configuration, Setup, Running, and Test. Registers not included in any of these categories can be assumed to be intended for diagnostic purposes. CSR10* Logical Address Filter[47:32] CSR11* Logical Address Filter[63:48] CSR12*^ Physical Address[15:0] n PCI Configuration Registers CSR13*^ Physical Address[31:16] These registers are intended to be initialized by the system initialization procedure (e.g., BIOS device initialization routine) to program the operation of the controller PCI bus interface. CSR14*^ Physical Address[47:32] CSR15* Mode CSR24* Base Address of Receive Ring Lower The following is a list of the registers that would typically need to be programmed once during the initialization of the Am79C978 controller within a system: CSR25* Base Address of Receive Ring Upper CSR30* Base Address of Transmit Ring Lower CSR31* Base Address of Transmit Ring Upper CSR47* Transmit Polling Interval -- PCI Expansion ROM Base Address register CSR49* Receive Polling Interval -- PCI Interrupt Line register CSR76* Receive Ring Length CSR78* Transmit Ring Length CSR80 DMA Transfer Counter and FIFO Threshold Control CSR82 Bus Activity Timer CSR100 Memory Error Timeout CSR116^ OnNow Miscellaneous CSR122 Receiver Packet Alignment Control -- PCI I/O Base Address or Memory Mapped I/O Base Address register -- PCI Latency Timer register -- PCI Status register -- PCI Command register -- OnNow register n Setup Registers These registers are intended to be initialized by the device driver to program the operation of various controller features. Am79C978 101 CSR125^ MAC Enhanced Configuration Control n Running Registers BCR2^ Miscellaneous Configuration BCR4^ LED0 Status BCR5^ LED1 Status These registers are intended to be used by the device driver software after the Am79C978 controller is running to access status information and to pass control information. BCR6^ LED2 Status BCR7^ LED3 Status BCR9^ Full-Duplex Control BCR18^ Bus and Burst Control BCR19 EEPROM Control and Status BCR20 Software Style BCR22^ PCI Latency BCR23^ PCI Subsystem Vendor ID BCR24^ PCI Subsystem ID BCR25^ SRAM Size BCR26^ SRAM Boundary BCR27^ SRAM Interface Control BCR32^ Internal PHY Control and Status BCR33^ Internal PHY Address BCR35^ PCI Vendor ID BCR36 PCI Power Management Capabilities (PMC) Alias Register BCR37 PCI DATA Register 0 (DATA0) Alias Register BCR38 PCI DATA Register 1 (DATA1) Alias Register PCI Configuration Registers BCR39 PCI DATA Register 2 (DATA2) Alias Register Offset 00h BCR40 PCI DATA Register 3 (DATA3) Alias Register BCR41 PCI DATA Register 4 (DATA4) Alias Register BCR42 PCI DATA Register 5 (DATA5) Alias Register BCR43 BCR44 PCI DATA Register 6 (DATA6) Alias Register PCI DATA Register 7 (DATA7) Alias Register The following is a list of the registers that would typically need to be periodically read and perhaps written during the normal running operation of the Am79C978 controller within a system. Each of these registers contains control bits, or status bits, or both. RAP Register Address Port CSR0 Controller Status CSR3 Interrupt Masks and Deferral Control CSR4 Test and Features Control CSR5 Extended Control and Interrupt CSR7 Extended Control and Interrupt2 CSR112 Missed Frame Count CSR114 Receive Collision Count BCR32 Internal PHY Control and Status BCR33 Internal PHY Address BCR34 Internal PHY Management Data n Test Registers These registers are intended to be used only for testing and diagnostic purposes. Those registers not included in any of the above lists can be assumed to be intended for diagnostic purposes. PCI Vendor ID Register The PCI Vendor ID register is a 16-bit register that identifies the manufacturer of the Am79C978 controller. AMD's Vendor ID is 1022h. Note that this Vendor ID is not the same as the Manufacturer ID in CSR88 and CSR89. The Vendor ID is assigned by the PCI Special Interest Group. The PCI Vendor ID register is located at offset 00h in the PCI Configuration Space. It is read only. This register is the same as BCR35 and can be written by the EEPROM. PCI Device ID Register BCR45 OnNow Pattern Matching Register 1 Offset 02h BCR46 OnNow Pattern Matching Register 2 BCR47 OnNow Pattern Matching Register 3 BCR48 LED4 Status The PCI Device ID register is a 16-bit register that helps identify the Am79C978 controller within AMD's product line. The Am79C978 Device ID is 2001h. Note that this Device ID is not the same as the part number in CSR88 and CSR89. The Device ID is assigned by BCR49 PHY Select 102 Am79C978 AMD. The PCI Device ID register is located at offset 02h in the PCI Configuration Space. It is read only. data parity error occurred during a master cycle. PERREN also enables reporting address parity errors through the SERR pin and the SERR bit in the PCI Status register. PCI Command Register Offset 04h The PCI Command register is a 16-bit register used to control the gross functionality of the Am79C978 controller. It controls the Am79C978 controller's ability to generate and respond to PCI bus cycles. To logically disconnect the Am79C978 device from all PCI bus cycles except configuration cycles, a value of 0 should be written to this register. The PCI Command register is located at offset 04h in the PCI Configuration Space. It is read and written by the host. Bit Name Description 15-10 RES Reserved locations. Read as zeros; write operations have no effect. 9 FBTBEN Fast Back-to-Back Enable. Read as zero; write operations have no effect. The Am79C978 controller will not generate Fast Back-toBack cycles. 8 SERREN SERR Enable. Controls the assertion of the SERR pin. SERR is disabled when SERREN is cleared. SERR will be asserted on detection of an address parity error and if both SERREN and PERREN (bit 6 of this register) are set. SERREN is cleared by H_RESET and is not effected by S_RESET or by setting the STOP bit. 7 RES Reserved location. Read as zeros; write operations have no effect. 6 PERREN Parity Error Response Enable. Enables the parity error response functions. When PERREN is 0 and the Am79C978 controller detects a parity error, it only sets the Detected Parity Error bit in the PCI Status register. When PERREN is 1, the Am79C978 controller asserts PERR on the detection of a data parity error. It also sets the DATAPERR bit (PCI Status register, bit 8), when the PERREN is cleared by H_RESET and is not affected by S_RESET or by setting the STOP bit. 5 VGASNOOP VGA Palette Snoop. Read as zero; write operations have no effect. 4 MWIEN Memory Write and Invalidate Cycle Enable. Read as zero; write operations have no effect. The Am79C978 controller only generates Memory Write cycles. 3 SCYCEN Special Cycle Enable. Read as zero; write operations have no effect. The Am79C978 controller ignores all Special Cycle operations. 2 BMEN Bus Master Enable. Setting BMEN enables the Am79C978 controller to become a bus master on the PCI bus. The host must set BMEN before setting the INIT or STRT bit in CSR0 of the Am79C978 controller. BMEN is cleared by H_RESET and is not effected by S_RESET or by setting the STOP bit. 1 Am79C978 MEMEN Memory Space Access Enable. The Am79C978 controller will ignore all memory accesses when MEMEN is cleared. The host must set MEMEN before the first memory access to the device. For memory mapped I/O, the host must program the PCI Memory Mapped I/O Base Address register with a valid memory address before setting MEMEN. For accesses to the Expansion ROM, the host must program the PCI Expansion ROM Base Address register at offset 30h with a valid memory address before setting MEMEN. The Am79C978 103 controller will only respond to accesses to the Expansion ROM when both ROMEN (PCI Expansion ROM Base Address register, bit 0) and MEMEN are set to 1. Since MEMEN also enables the memory mapped access to the Am79C978 I/O resources, the PCI Memory Mapped I/O Base Address register must be programmed with an address so that the device does not claim cycles not intended for it. * In master mode, during the data phase of all memory read commands. In master mode, during the data phase of the memory write command, the Am79C978 controller sets the PERR bit if the target reports a data parity error by asserting the PERR signal. PERR is not effected by the state of the Parity Error Response enable bit (PCI Command register, bit 6). MEMEN is cleared by H_RESET and is not effected by S_RESET or by setting the STOP bit. 0 IOEN I/O Space Access Enable. The Am79C978 controller will ignore all I/O accesses when IOEN is cleared. The host must set IOEN before the first I/O access to the device. The PCI I/O Base Address register must be programmed with a valid I/O address before setting IOEN. PERR is set by the Am79C978 controller and cleared by writing a 1. Writing a 0 has no effect. PERR is cleared by H_RESET and is not affected by S_RESET or by setting the STOP bit. 14 SERR IOEN is cleared by H_RESET and is not effected by S_RESET or by setting the STOP bit. SERR is set by the Am79C978 controller and cleared by writing a 1. Writing a 0 has no effect. SERR is cleared by H_RESET and is not affected by S_RESET or by setting the STOP bit. PCI Status Register Offset 06h The PCI Status register is a 16-bit register that contains status information for the PCI bus related events. It is located at offset 06h in the PCI Configuration Space. Bit Name Description 15 PERR Parity Error. PERR is set when the Am79C978 controller detects a parity error. 13 RMABORT Received Master Abort. RMABORT is set when the Am79C978 controller terminates a master cycle with a master abort sequence. RMABORT is set by the Am79C978 controller and cleared by writing a 1. Writing a 0 has no effect. RMABORT is cleared by H_RESET and is not affected by S_RESET or by setting the STOP bit. The Am79C978 controller samples the AD[31:0], C/BE[3:0], and the PAR lines for a parity error at the following times: * In slave mode, during the address phase of any PCI bus command. 12 * In slave mode, for all I/O, memory, and configuration write commands that select the Am79C978 controller when data is transferred (TRDY and IRDY are asserted). 104 Signaled SERR. SERR is set when the Am79C978 controller detects an address parity error and both SERREN and PERREN (PCI Command register, bits 8 and 6) are set. Am79C978 RTABORT Received Target Abort. RTABORT is set when a target terminates an Am79C978 master cycle with a target abort sequence. RTABORT is set by the Am79C978 controller and cleared by writing a 1. Writing a 0 has no effect. RTABORT is cleared by H_RESET and is not affected by S_RESET or by setting the STOP bit. 11 STABORT Send Target Abort. Read as zero; write operations have no effect. The Am79C978 controller will never terminate a slave access with a target abort sequence. fast back-to-back transactions with the first transaction addressing a different target. 6-5 RES 4 NEW_CAP New Capabilities. This bit indicates whether this function implements a list of extended capabilities such as PCI power management. When set, this bit indicates the presence of New Capabilities. A value of 0 means that this function does not implement New Capabilities. STABORT is read only. 10-9 DEVSEL Device Select Timing. DEVSEL is set to 01b (medium), which means that the Am79C978 controller will assert DEVSEL two clock periods after FRAME is asserted. Read as one; write operations have no effect. The Am79C978 controller supports the Linked Additional Capabilities List. 3-0 DEVSEL is read only. 8 7 DATAPERR FBTBC Data Parity Error Detected. DATAPERR is set when the Am79C978 controller is the current bus master and it detects a data parity error and the Parity Error Response enable bit (PCI Command register, bit 6) is set. Reserved locations. Read as zero; write operations have no effect. RES Reserved locations. Read as zero; write operations have no effect. PCI Revision ID Register Offset 08h The PCI Revision ID register is an 8-bit register that specifies the Am79C978 controller revision number. The value of this register is 5Xh with the lower four bits being silicon-revision dependent. During the data phase of all memory read commands, the Am79C978 controller checks for parity error by sampling AD[31:0], C/BE[3:0], and the PAR lines. During the data phase of all memory write commands, the Am79C978 controller checks the PERR input to detect whether the target has reported a parity error. The PCI Revision ID register is located at offset 08h in the PCI Configuration Space. It is read only. DATAPERR is set by the Am79C978 controller and cleared by writing a 1. Writing a 0 has no effect. DATAPERR is cleared by H_RESET and is not affected by S_RESET or by setting the STOP bit. The PCI Programming Interface register is located at offset 09h in the PCI Configuration Space. It is read only. Fast Back-To-Back Capable. Read as one; write operations have no effect. The Am79C978 controller is capable of accepting PCI Programming Interface Register Offset 09h The PCI Programming Interface register is an 8-bit register that identifies the programming interface of Am79C978 controller. PCI does not define any specific register-level programming interfaces for network devices. The value of this register is 00h. PCI Sub-Class Register Offset 0Ah The PCI Sub-Class register is an 8-bit register that identifies specifically the function of the Am79C978 controller. The value of this register is 00h which identifies the Am79C978 device as an Ethernet controller. The PCI Sub-Class register is located at offset 0Ah in the PCI Configuration Space. It is read only. Am79C978 105 PCI Base-Class Register 6-0 LAYOUT Offset 0Bh The PCI Base-Class register is an 8-bit register that broadly classifies the function of the Am79C978 controller. The value of this register is 02h, which classifies the Am79C978 device as a networking controller. The PCI Base-Class register is located at offset 0Bh in the PCI Configuration Space. It is read only. PCI Latency Timer Register Offset 0Dh The PCI Latency Timer register is an 8-bit register that specifies the minimum guaranteed time the Am79C978 controller will control the bus once it starts its bus mastership period. The time is measured in clock cycles. Every time the Am79C978 controller asserts FRAME at the beginning of a bus mastership period, it will copy the value of the PCI Latency Timer register into a counter and start counting down. The counter will freeze at 0. When the system arbiter removes GNT while the counter is non-zero, the Am79C978 controller will continue with its data transfers. It will only release the bus when the counter has reached 0. PCI I/O Base Address Register Offset 10h The PCI I/O Base Address register is a 32-bit register that determines the location of the Am79C978 I/O resources in all of I/O space. It is located at offset 10h in the PCI Configuration Space. Bit Name Description 31-5 IOBASE I/O base address most significant 27 bits. These bits are written by the host to specify the location of the Am79C978 I/O resources in all of I/O space. IOBASE must be written with a valid address before the Am79C978 controller slave I/O mode is turned on by setting the IOEN bit (PCI Command register, bit 0). The PCI Latency Timer is only significant in burst transactions, where FRAME stays asserted until the last data phase. In a non-burst transaction, FRAME is only asserted during the address phase. The internal latency counter will be cleared and suspended while FRAME is deasserted. When the Am79C978 controller is enabled for I/O mode (IOEN is set), it monitors the PCI bus for a valid I/O command. If the value on AD[31:5] during the address phase of the cycles matches the value of IOBASE, the Am79C978 controller will drive DEVSEL indicating it will respond to the access. All eight bits of the PCI Latency Timer register are programmable. The host should read the Am79C978 PCI MIN_GNT and PCI MAX_LAT registers to determine the latency requirements for the device and then initialize the Latency Timer register with an appropriate value. The PCI Latency Timer register is located at offset 0Dh in the PCI Configuration Space. It is read and written by the host. The PCI Latency Timer register is cleared by H_RESET and is not effected by S_RESET or by setting the STOP bit. IOBASE is read and written by the host. IOBASE is cleared by H_RESET and is not affected by S_RESET or by setting the STOP bit. PCI Header Type Register Offset 0Eh The PCI Header Type register is an 8-bit register that describes the format of the PCI Configuration Space locations 10h to 3Ch and that identifies a device to be single or multi-function. The PCI Header Type register is located at address 0Eh in the PCI Configuration Space. It is read only. Bit Name Description 7 FUNCT Single-function/multi-function device. Read as zero; write operations have no effect. The Am79C978 controller is a single function device. 106 PCI configuration space layout. Read as zeros; write operations have no effect. The layout of the PCI configuration space locations 10h to 3Ch is as shown in Table 24. 4-2 IOSIZE I/O size requirements. Read as zeros; write operations have no effect. IOSIZE indicates the size of the I/O space the Am79C978 controller requires. When the host writes a value of FFFF FFFFh to the I/O Base Address register, it will read back a value of 0 in bits 4-2. That indicates an Am79C978 I/O space requirement of 32 bytes. 1 Am79C978 RES Reserved location. Read as zero; write operations have no effect. 0 IOSPACE I/O space indicator. Read as one; write operations have no effect. Indicating that this base address register describes an I/O base address. memory space requirement of 32 bytes. 3 PCI Memory Mapped I/O Base Address Register Offset 14h The PCI Memory Mapped I/O Base Address register is a 32-bit register that determines the location of the Am79C978 I/O resources in all of memory space. It is located at offset 14h in the PCI Configuration Space. Bit Name 31-5 MEMBASE Memory mapped I/O base address most significant 27 bits. These bits are written by the host to specify the location of the Am79C978 I/O resources in all of memory space. MEMBASE must be written with a valid address before the Am79C978 controller slave memory mapped I/O mode is turned on by setting the MEMEN bit (PCI Command register, bit 1). 4 MEMSIZE Description 2-1 0 PREFETCH Prefetchable. Read as zero; write operations have no effect. Indicates that memory space controlled by this base address register is not prefetchable. Data in the memory mapped I/O space cannot be prefetched. Because one of the I/O resources in this address space is a Reset register, the order of the read accesses is important. TYPE Memory type indicator. Read as zeros; write operations have no effect. Indicates that this base address register is 32 bits wide and mapping can be done anywhere in the 32-bit memory space. MEMSPACE Memory space indicator. Read as zero; write operations have no effect. Indicates that this base address register describes a memory base address. When the Am79C978 controller is enabled for memory mapped I/O mode (MEMEN is set), it monitors the PCI bus for a valid memory command. If the value on AD[31:5] during the address phase of the cycles matches the value of MEMBASE, the Am79C978 controller will drive DEVSEL indicating it will respond to the access. PCI Subsystem Vendor ID Register MEMBASE is read and written by the host. MEMBASE is cleared by H_RESET and is not affected by S_RESET or by setting the STOP bit. The PCI Subsystem Vendor ID register is located at offset 2Ch in the PCI Configuration Space. It is read only. Memory mapped I/O size requirements. Read as zeros; write operations have no effect. MEMSIZE indicates the size of the memory space the Am79C978 controller requires. When the host writes a value of FFFF FFFFh to the Memory Mapped I/O Base Address register, it will read back a value of 0 in bit 4. That indicates a Am79C978 Offset 2Ch The PCI Subsystem Vendor ID register is a 16-bit register that together with the PCI Subsystem ID uniquely identifies the add-in card or subsystem the Am79C978 controller is used in. Subsystem Vendor IDs can be obtained from the PCI SIG. A value of 0 (the default) indicates that the Am79C978 controller does not support subsystem identification. The PCI Subsystem Vendor ID is an alias of BCR23, bits 15-0. It is programmable through the EEPROM. PCI Subsystem ID Register Offset 2Eh The PCI Subsystem ID register is a 16-bit register that together with the PCI Subsystem Vendor ID uniquely identifies the add-in card or subsystem the Am79C978 controller is used in. The value of the Subsystem ID is up to the system vendor. A value of 0 (the default) indicates that the Am79C978 controller does not support subsystem identification. The PCI Subsystem ID is an alias of BCR24, bits 15-0. It is programmable through the EEPROM. The PCI Subsystem ID register is located at offset 2Eh in the PCI Configuration Space. It is read only. Am79C978 107 PCI Expansion ROM Base Address Register 19-1, indicating an Expansion ROM size of 1M. Offset 30h The PCI Expansion ROM Base Address register is a 32-bit register that defines the base address, size, and address alignment of an Expansion ROM. It is located at offset 30h in the PCI Configuration Space. Bit Name 31-20 ROMBASE Expansion ROM base address most significant 12 bits. These bits are written by the host to specify the location of the Expansion ROM in all of memory space. ROMBASE must be written with a valid address before the Am79C978 Expansion ROM access is enabled by setting ROMEN (PCI Expansion ROM Base Address register, bit 0) and MEMEN (PCI Command register, bit 1). Description Since the 12 most significant bits of the base address are programmable, the host can map the Expansion ROM on any 1M boundary. When the Am79C978 controller is enabled for Expansion ROM access (ROMEN and MEMEN are set to 1), it monitors the PCI bus for a valid memory command. If the value on AD[31:2] during the address phase of the cycle falls between ROMBASE and ROMBASE + 1M - 4, the Am79C978 controller will drive DEVSEL indicating it will respond to the access. ROMBASE is read and written by the host. ROMBASE is cleared by H_RESET and is not affected by S_RESET or by setting the STOP bit. 19-1 108 ROMSIZE Note that ROMSIZE only specifies the maximum size of Expansion ROM the Am79C978 controller supports. A smaller ROM can also be used. The actual size of the code in the Expansion ROM is always determined by reading the Expansion ROM header. ROM size. Read as zeros; write operation have no effect. ROMSIZE indicates the maximum size of the Expansion ROM the Am79C978 controller can support. The host can determine the Expansion ROM size by writing FFFF FFFFh to the Expansion ROM Base Address register. It will read back a value of 0 in bit 0 ROMEN Expansion ROM Enable. Written by the host to enable access to the Expansion ROM. The Am79C978 controller will only respond to accesses to the Expansion ROM when both ROMEN and MEMEN (PCI Command register, bit 1) are set to 1. ROMEN is read and written by the host. ROMEN is cleared by H_RESET and is not effected by S_RESET or by setting the STOP bit. PCI Capabilities Pointer Register Offset 34h Bit Name Description 7-0 CAP_PTR The PCI Capabilities Pointer register is an 8-bit register that points to a linked list of capabilities implemented on this device. This register has a default value of 40h. The PCI Capabilities Pointer register is located at offset 34h in the PCI Configuration Space. It is read only. PCI Interrupt Line Register Offset 3Ch The PCI Interrupt Line register is an 8-bit register that is used to communicate the routing of the interrupt. This register is written by the POST software as it initializes the Am79C978 controller in the system. The register is read by the network driver to determine the interrupt channel which the POST software has assigned to the Am79C978 controller. The PCI Interrupt Line register is not modified by the Am79C978 controller. It has no effect on the operation of the device. The PCI Interrupt Line register is located at offset 3Ch in the PCI Configuration Space. It is read and written by Am79C978 the host. It is cleared by H_RESET and is not affected by S_RESET or by setting the STOP bit. the PCI Configuration Space. It is read only. PCI Interrupt Pin Register PCI Next Item Pointer Register Offset 3Dh This PCI Interrupt Pin register is an 8-bit register that indicates the interrupt pin that the Am79C978 controller is using. The value for the Am79C978 Interrupt Pin register is 01h, which corresponds to INTA. Offset 41h Bit Name 7-0 NXT_ITM_PTR The PCI Interrupt Pin register is located at offset 3Dh in the PCI Configuration Space. It is read only. The Next Item Pointer Register points to the starting address of the next capability. The pointer at this offset is a null pointer, indicating that this is the last capability in the linked list of the capabilities. This register has a default value of 0h. PCI MIN_GNT Register Offset 3Eh The PCI MIN_GNT register is an 8-bit register that specifies the minimum length of a burst period that the Am79C978 device needs to keep up with the network activity. The length of the burst period is calculated assuming a clock rate of 33 MHz. The register value specifies the time in units of 1/4 s. The PCI MIN_GNT register is an alias of BCR22, bits 7-0. It is recommended that BCR22 be programmed to a value of 1818h. The host should use the value in this register to determine the setting of the PCI Latency Timer register. The PCI MIN_GNT register is located at offset 3Eh in the PCI Configuration Space. It is read only. PCI MAX_LAT Register Offset 3Fh The PCI MAX_LAT register is an 8-bit register that specifies the maximum arbitration latency the Am79C978 controller can sustain without causing problems to the network activity. The register value specifies the time in units of 1/4 s. The MAX_LAT register is an alias of BCR22, bits 15-8. It is recommended that BCR22 be programmed to a value of 1818h. Description The PCI Next Pointer Register is located at offset 41h in the PCI Configuration Space. It is read only. PCI Power Management Capabilities Register (PMC) Offset 42h Note: All bits of this register are loaded from the EEPROM. The register is aliased to BCR36 for testing purposes. Bit Name Description 15-11 PME_SPT PME Support. This 5-bit field indicates the power states in which the function may assert PME. A value of 0b for any bit indicates that the function is not capable of asserting the PME signal while in that power state. The host should use the value in this register to determine the setting of the PCI Latency Timer register. The PCI MAX_LAT register is located at offset 3Fh in the PCI Configuration Space. It is read only. PCI Capability Identifier Register Offset 40h Bit(11) XXXX1b - PME can be asserted from D0. Bit(12) XXX1Xb - PME can be asserted from D1. Bit(13) XX1XXb - PME can be asserted from D2. Bit Name Description 7-0 CAP_ID This register, when set to 1, identifies the linked list item as being the PCI Power Management registers. This register has a default value of 1h. Bit(14) X1XXXb - PME can be asserted from D3hot. The PCI Capabilities Identifier register is located at offset 40h in PME_SPT is read only. Am79C978 Bit(15) 1XXXXb - PME can be asserted from D3cold. 109 10 D2_SPT D2 Support. If this bit is a 1, this function supports the D2 Power Management State. before the generic class device driver is able to use it. This bit is read only. This bit is read only. 9 D1_SPT D1 Support. If this bit is a 1, this function supports the D1 Power Management State. 4 RES Reserved location. 3 PME_CLK PME Clock. When this bit is a 1, it indicates that the function relies on the presence of the PCI clock for PME operation. When this bit is a 0 it indicates that no PCI clock is required for the function to generate PME. This bit is read only. 8-6 AUX_CURRENT Auxiliary Current Requirements. This 3-bit field reports the 3.3Vaux current requirements for the PCI function. If the Data Register has been implemented by this function, then reads of this field must return a value of 000b and the Data Register will take precedence over this field for 3.3Vaux current requirement reporting. If PME generation from D3cold is not supported by the function (PMC (15) = 0), this field must return a value of 000b when read. For functions that support PME from D3cold and do not implement the Data Register, the following bit assignments apply: Bit 876 3.3Vaux Max. Current Required 111 375 mA 110 320 mA 101 270 mA 100 220 mA 011 160 mA 010 100 mA 001 55 mA 000 0 (self-powered) Functions that do not support PME generation in any state must return 0 for this field. This bit is read only. 2-0 PCI Power Management Control/Status Register (PMCSR) Offset 44h Bit 15 110 DSI Name Description PME_STATUS PME Status. This bit is set when the function would normally assert the PME signal independent of the state of the PME_EN bit. Writing a 1 to this bit will clear it and cause the function to stop asserting a PME (if enabled). Writing a 0 has no effect. If the function supports PME from D3cold, then this bit is sticky and must be explicitly cleared by the operating system each time the operating system is initially loaded. These bits are read only. 5 PMIS_VER Power Management Interface Specification Version. A value of 001b indicates that this function complies with revision 1.0 of the PCI Power Management Interface Specification. Device Specific Initialization. When this bit is 1, it indicates that special initialization of the function is required (beyond the standard PCI configuration header) Am79C978 This bit is always read/write accessible. Sticky bit. This bit is reset by POR. H_RESET, S_RESET, or setting the STOP bit has no effect. 14-13 DATA_SCALE Data Scale. This 2-bit read-only field indicates the scaling factor to be used when interpreting the value of the Data register. The value and meaning of this field will vary depending on the DATA_SCALE field. These bits are always read/write accessible. PCI PMCSR Bridge Support Extensions Register Offset 46h These bits are read only. 12-9 These bits can be written and read, but their contents have no effect on the operation of the device. Bit DATA_SEL Data Select. This optional 4-bit field is used to select which data is reported through the Data register and DATA_SCALE field. 7-0 These bits are always read/write accessible. Sticky bit. These bits are reset by POR. H_RESET, S_RESET, or setting the STOP bit has no effect. 8 PME_EN PME Enable. When a 1, PME_EN enables the function to assert PME. When a 0, PME assertion is disabled. Name Description PMCSR_BSE The PCI PMCSR Bridge Support Extensions Register is an 8-bit register. PMCSR Bridge Support Extensions are not supported. This register has a default value of 00h. The PCI PMCSR Bridge Support Extensions register is located at offset 46h in the PCI Configuration Space. These bits are read only. PCI Data Register Offset 47h This bit defaults to "0" if the function does not support PME generation from D3cold. Note: All bits of this register are loaded from the EEPROM. The register is aliased to lower bytes of the BCR37-BCR44 for testing purposes. If the function supports PME from D3cold, then this bit is sticky and must be explicitly cleared by the operating system each time the operating system is initially loaded. Bit Name 7-0 DATA_REG The PCI Data Register is an 8-bit register. Refer to the "PCI Bus Power Management Interface Specification" version 1.0 for a more detailed description of this register. This bit is always read/write accessible. Sticky bit. This bit is reset by POR. H_RESET, S_RESET, or setting the STOP bit has no effect. 7-2 1-0 RES Reserved locations. These bits are read only. PWR_STATE Power State. This 2-bit field is used both to determine the current power state of a function and to set the function into a new power state. The definition of the field values is given below. 00b - D0. 01b - D1. 10b - D2. 11b - D3. Description The PCI DATA register is located at offset 47h in the PCI Configuration Space. It is read only. RAP Register The RAP (Register Address Pointer) register is used to gain access to CSR and BCR registers on board the Am79C978 controller. The RAP contains the address of a CSR or BCR. As an example of RAP use, consider a read access to CSR4. In order to access this register, it is necessary to first load the value 0004h into the RAP by performing a write access to the RAP offset of 12h (12h when WIO mode has been selected, 14h when DWIO mode has been selected). Then a second access is performed, this time to the RDP offset of 10h (for either WIO or DWIO mode). The RDP access is a read access, and Am79C978 111 since RAP has just been loaded with the value of 0004h, the RDP read will yield the contents of CSR4. A read of the BDP at this time (offset of 16h when WIO mode has been selected, 1Ch when DWIO mode has been selected) will yield the contents of BCR4, since the RAP is used as the pointer into both BDP and RDP space. This bit is always read accessible only. Write operations are ignored. 14 RES Reserved locations. This bit is always read/write accessible. Read returns zero. 13 CERR Collision Error. Collision Error is set by the Am79C978 controller when the device operates in halfduplex mode and the collision inputs to the GPSI port fail to activate within 20 network bit times after the chip terminates transmission (SQE Test). This feature is a transceiver test feature. CERR reporting is disabled when the GPSI port is active and the Am79C978 controller operates in full-duplex mode. RAP: Register Address Port Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-8 RES Reserved locations. Read and written as zeros. 7-0 RAP Register Address Port. The value of these 8 bits determines which CSR or BCR will be accessed when an I/O access to the RDP or BDP port, respectively, is performed. When the MII port is selected, CERR is only reported when the external PHY is operating as a half-duplex 10BASE-T PHY. A write access to undefined CSR or BCR locations may cause unexpected reprogramming of the Am79C978 control registers. A read access will yield undefined values. CERR assertion will not result in an interrupt being generated. CERR assertion will set the ERR bit. These bits are always read/write accessible. RAP is cleared by H_RESET or S_RESET and is unaffected by setting the STOP bit. This bit is always read/write accessible. CERR is cleared by the host by writing a 1. Writing a 0 has no effect. CERR is cleared by H_RESET, S_RESET, or by setting the STOP bit. Control and Status Registers (CSRs) The CSR space is accessible by performing accesses to the RDP (Register Data Port). The particular CSR that is read or written during an RDP access will depend upon the current setting of the RAP. RAP serves as a pointer into the CSR space. 12 CSR0: Controller Status and Control Register Certain bits in CSR0 indicate the cause of an interrupt. The register is designed so that these indicator bits are cleared by writing ones to those bit locations. This means that the software can read CSR0 and write back the value just read to clear the interrupt condition. Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15 ERR Error. Error is set by the OR of CERR, MISS, and MERR. ERR remains set as long as any of the error flags are true. 112 Am79C978 MISS Missed Frame. Missed Frame is set by the Am79C978 controller when it has lost an incoming receive frame resulting from a Receive Descriptor not being available. This bit is the only immediate indication that receive data has been lost since there is no current receive descriptor. The Missed Frame Counter (CSR112) also increments each time a receive frame is missed. When MISS is set, INTA is asserted if IENA is 1 and the mask bit MISSM (CSR3, bit 12) is 0. MISS assertion will set the ERR bit, regardless of the settings of IENA and MISSM. This bit is always read/write accessible. MISS is cleared by the host by writing a 1. Writing a 0 has no effect. MISS is cleared by H_RESET, S_RESET, or by setting the STOP bit. 11 MERR 9 TINT Memory Error. Memory Error is set by the Am79C978 controller when it requests the use of the system interface bus by asserting REQ and has not received GNT assertion after a programmable length of time. The length of time in microseconds before MERR is asserted will depend upon the setting of the Bus Timeout Register (CSR100). The default setting of CSR100 will give a MERR after 153.6 ms of bus latency. When MERR is set, INTA is asserted if IENA is 1 and the mask bit MERRM (CSR3, bit 11) is 0. MERR assertion will set the ERR bit, regardless of the settings of IENA and MERRM. When TINT is set, INTA is asserted if IENA is 1 and the mask bit TINTM (CSR3, bit 9) is 0. TINT will not be set if TINTOKD (CSR5, bit 15) is set to 1 and the transmission was successful. This bit is always read/write accessible. TINT is cleared by the host by writing a 1. Writing a 0 has no effect. TINT is cleared by H_RESET, S_RESET, or by setting the STOP bit. 8 IDON This bit is always read/write accessible. MERR is cleared by the host by writing a 1. Writing a 0 has no effect. MERR is cleared by H_RESET, S_RESET, or by setting the STOP bit. 10 RINT Receive Interrupt is set by the Am79C978 controller after the last descriptor of a receive frame has been update by writing a 0 to the ownership bit (OWN). RINT may also be set when the first descriptor of a receive frame has been updated by writing a 0 to the ownership bit if the LAPPEN bit of CSR3 has been set to a 1. Transmit Interrupt is set by the Am79C978 controller after the OWN bit in the last descriptor of a transmit frame has been cleared to indicate the frame has been sent or an error occurred in the transmission. Initialization Done is set by the Am79C978 controller after the initialization sequence has completed. When IDON is set, the Am79C978 controller has read the initialization block from memory. When IDON is set, INTA is asserted if IENA is 1 and the mask bit IDONM (CSR3, bit 8) is 0. This bit is always read/write accessible. IDON is cleared by the host by writing a 1. Writing a 0 has no effect. IDON is cleared by H_RESET, S_RESET, or by setting the STOP bit. 7 When RINT is set, INTA is asserted if IENA is 1 and the mask bit RINTM (CSR3, bit 10) is 0. This bit is always read/write accessible. RINT is cleared by the host by writing a 1. Writing a 0 has no effect. RINT is cleared by H_RESET, S_RESET, or by setting the STOP bit. Am79C978 INTR Interrupt Flag indicates that one or more following interrupt causing conditions has occurred: EXDINT, IDON, MERR, MISS, MFCO, RCVCCO, RINT, SINT, TINT, TXSTRT, UINT, STINT, MREINT, MCCINT, MIIPDTINT, MAPINT and the associated mask or enable bit is programmed to allow the event to cause an interrupt. If IENA is set to 1 and INTR is set, INTA will be active. When INTR is set by SINT or SLPINT, INTA will be active independent of the state of IENA. 113 This bit is always read accessible. INTR is read only. INTR is cleared by clearing all of the active individual interrupt bits that have not been masked out. 6 IENA will be reset and no Transmit Descriptor Ring access will occur. TDMD is required to be set if the TXDPOLL bit in CSR4 is set. Setting TDMD while TXDPOLL = 0 merely hastens the controller's response to a Transmit Descriptor Ring Entry. Interrupt Enable allows INTA to be active if the Interrupt Flag is set. If IENA = 0, then INTA will be disabled regardless of the state of INTR. This bit is always read/write accessible. TDMD is set by writing a 1. Writing a 0 has no effect. TDMD will be cleared by the Buffer Management Unit when it fetches a Transmit Descriptor. TDMD is cleared by H_RESET or S_RESET and setting the STOP bit. This bit is always read/write accessible. IENA is set by writing a 1 and cleared by writing a 0. IENA is cleared by H_RESET or S_RESET and setting the STOP bit. 5 RXON Receive On indicates that the receive function is enabled. RXON is set if DRX (CSR15, bit 0) is set to 0 after the START bit is set. If INIT and START are set together, RXON will not be set until after the initialization block has been read in. 2 STOP This bit is always read accessible. RXON is read only. RXON is cleared by H_RESET or S_RESET and setting the STOP bit. 4 TXON Transmit On indicates that the transmit function is enabled. TXON is set if DTX (CSR15, bit 1) is set to 0 after the START bit is set. If INIT and START are set together, TXON will not be set until after the initialization block has been read in. This bit is always read/write accessible. STOP is set by writing a 1, by H_RESET or S_RESET. Writing a 0 has no effect. STOP is cleared by setting either STRT or INIT. 1 STRT This bit will reset if the DXSUFLO bit (CSR3, bit 6) is reset and there is an underflow condition encountered. Read accessible always. TXON is read only. TXON is cleared by H_RESET or S_RESET and setting the STOP bit. 3 114 TDMD STOP assertion disables the chip from all DMA activity. The chip remains inactive until either STRT or INIT are set. If STOP, STRT, and INIT are all set together, STOP will override STRT and INIT. STRT assertion enables the Am79C978 controller to send and receive frames and perform buffer management operations. Setting STRT clears the STOP bit. If STRT and INIT are set together, the Am79C978 controller initialization will be performed first. This bit is always read/write accessible. STRT is set by writing a 1. Writing a 0 has no effect. STRT is cleared by H_RESET, S_RESET, or by setting the STOP bit. 0 Transmit Demand, when set, causes the Buffer Management Unit to access the Transmit Descriptor Ring without waiting for the poll-time counter to elapse. If TXON is not enabled, TDMD bit Am79C978 INIT INIT assertion enables the Am79C978 controller to begin the initialization procedure which reads in the initialization block from memory. Setting INIT clears the STOP bit. If STRT and INIT are set together, the Am79C978 controller initialization will be per- formed first. INIT is not cleared when the initialization sequence has completed. dress. Therefore, whenever SSIZE32 = 0, the IADR[31:24] bits will be appended to the 24-bit initialization address, to each 24bit descriptor base address, and to each beginning 24-bit buffer address in order to form complete 32-bit addresses. The upper 8 bits that exist in the descriptor address registers and the buffer address registers which are stored on board the Am79C978 controller will be overwritten with the IADR[31:24] value, so that CSR accesses to these registers will show the 32-bit address that includes the appended field. This bit is always read/write accessible. INIT is set by writing a 1. Writing a 0 has no effect. INIT is cleared by H_RESET, S_RESET, or by setting the STOP bit. CSR1: Initialization Block Address 0 Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 IADR[15:0] Lower 16 bits of the address of the Initialization Block. Bit locations 1 and 0 must both be 0 to align the initialization block to a DWord boundary. If SSIZE32 = 1, then software will provide 32-bit pointer values for all of the shared software structures - i.e., descriptor bases and buffer addresses, and therefore, IADR[31:24] will not be written to the upper 8 bits of any of these resources, but it will be used as the upper 8 bits of the initialization address. This register is aliased with CSR16. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or by setting the STOP bit. This register is aliased with CSR17. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or by setting the STOP bit. CSR2: Initialization Block Address 1 Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-8 IADR[31:24] If SSIZE32 is set (BCR20, bit 8), then the IADR[31:24] bits will be used strictly as the upper 8 bits of the initialization block address. However, if SSIZE32 is reset (BCR20, bit 8), then the IADR[31:24] bits will be used to generate the upper 8 bits of all bus mastering addresses, as required for a 32-bit address bus. Note that the 16-bit software structures specified by the SSIZE32 = 0 setting will yield only 24 bits of address for the Am79C978 bus master accesses, while the 32-bit hardware for which the Am79C978 controller is intended will require 32 bits of ad- 7-0 IADR[23:16] Bits 23 through 16 of the address of the Initialization Block. Whenever this register is written, CSR17 is updated with CSR2's contents. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or by setting the STOP bit. CSR3: Interrupt Masks and Deferral Control Bit 31-16 Am79C978 Name RES Description Reserved locations. Written as zeros and read as undefined. 115 15-13 RES Reserved locations. Read and written as zero. off when an UFLO error occurs (CSR0, TXON = 0). 12 MISSM Missed Frame Mask. If MISSM is set, the MISS bit will be masked and unable to set the INTR bit. When DXSUFLO is set to 1, the Am79C978 controller gracefully recovers from an UFLO error. It scans the transmit descriptor ring until it finds the start of a new frame and starts a new transmission. This bit is always read/write accessible. MISSM is cleared by H_RESET or S_RESET and is not affected by STOP. 11 MERRM This bit is always read/write accessible. DXSUFLO is cleared by H_RESET or S_RESET and is not affected by STOP. Memory Error Mask. If MERRM is set, the MERR bit will be masked and unable to set the INTR bit. 5 This bit is always read/write accessible. MERRM is cleared by H_RESET or S_RESET and is not affected by STOP. 10 RINTM Receive Interrupt Mask. If RINTM is set, the RINT bit will be masked and unable to set the INTR bit. This bit is always read/write accessible. RINTM is cleared by H_RESET or S_RESET and is not affected by STOP. 9 TINTM Transmit Interrupt Mask. If TINTM is set, the TINT bit will be masked and unable to set the INTR bit. This bit is always read/write accessible. TINTM is cleared by H_RESET or S_RESET and is not affected by STOP. 8 IDONM Initialization Done Mask. If IDONM is set, the IDON bit will be masked and unable to set the INTR bit. This bit is always read/write accessible. IDONM is cleared by H_RESET or S_RESET and is not affected by STOP. 7 RES Reserved location. Read and written as zero. 6 DXSUFLO Disable Transmit Stop on Underflow error. When DXSUFLO (CSR3, bit 6) is set to 0, the transmitter is turned 116 Am79C978 LAPPEN Look Ahead Packet Processing Enable. When set to a 1, the LAPPEN bit will cause the Am79C978 controller to generate an interrupt following the descriptor write operation to the first buffer of a receive frame. This interrupt will be generated in addition to the interrupt that is generated following the descriptor write operation to the last buffer of a receive packet. The interrupt will be signaled through the RINT bit of CSR0. Setting LAPPEN to a 1 also enables the Am79C978 controller to read the STP bit of receive descriptors. The Am79C978 controller will use the STP information to determine where it should begin writing a receive packet's data. Note that while in this mode, the Am79C978 controller can write intermediate packet data to buffers whose descriptors do not contain STP bits set to 1. Following the write to the last descriptor used by a packet, the Am79C978 controller will scan through the next descriptor entries to locate the next STP bit that is set to a 1. The Am79C978 controller will begin writing the next packets data to the buffer pointed to by that descriptor. Note that because several descriptors may be allocated by the host for each packet, and not all messages may need all of the descriptors that are allocated between descriptors that contain STP = 1, then some descriptors/ buffers may be skipped in the ring. While performing the search for the next STP bit that is set to 1, the Am79C978 controller will advance through the receive descriptor ring regardless of the state of ownership bits. If any of the entries that are examined during this search indicate Am79C978 controller ownership of the descriptor but also indicate STP = 0, then the Am79C978 controller will reset the OWN bit to 0 in these entries. If a scanned entry indicates host ownership with STP = 0, then the Am79C978 controller will not alter the entry, but will advance to the next entry. When the STP bit is found to be true, but the descriptor that contains this setting is not owned by the Am79C978 controller, then the Am79C978 controller will stop advancing through the ring entries and begin periodic polling of this entry. When the STP bit is found to be true, and the descriptor that contains this setting is owned by the Am79C978 controller, then the controller will stop advancing through the ring entries, store the descriptor information that it has just read, and wait for the next receive to arrive. See Appendix B for more information on the Look Ahead Packet Processing concept. 4 DXMT2PD Disable Transmit Two Part Deferral (see Medium Allocation section in the Media Access Management section for more details). If DXMT2PD is set, Transmit Two Part Deferral will be disabled. This bit is always read/write accessible. DXMT2PD is cleared by H_RESET or S_RESET and is not affected by STOP. 3 EMBA Enable Modified Back-off Algorithm (see the Contention Resolution section in Media Access Management section for more details). If EMBA is set, a modified back-off algorithm is implemented. This bit is always read/write accessible. EMBA is cleared by H_RESET or S_RESET and is not affected by STOP. 2 This behavior allows the host software to pre-assign buffer space in such a manner that the header portion of a receive packet will always be written to a particular memory area, and the data portion of a receive packet will always be written to a separate memory area. The interrupt is generated when the header bytes have been written to the header memory area. This bit is always read/write accessible. The LAPPEN bit will be reset to 0 by H_RESET or S_RESET and will be unaffected by STOP. Am79C978 BSWP Byte Swap. This bit is used to choose between big and little Endian modes of operation. When BSWP is set to a 1, big Endian mode is selected. When BSWP is set to 0, little Endian mode is selected. When big Endian mode is selected, the Am79C978 controller will swap the order of bytes on the AD bus during a data phase on accesses to the FIFOs only. Specifically, AD[31:24] becomes Byte 0, AD[23:16] becomes Byte 1, AD[15:8] becomes Byte 2, and AD[7:0] becomes Byte 3 when big Endian mode is selected. When little Endian mode is selected, the order of bytes on the AD bus during a data phase is: AD[31:24] is Byte 3, AD[23:16] is Byte 2, AD[15:8] is Byte 1, and AD[7:0] is Byte 0. Byte swap only affects data transfers that involve the FIFOs. Initialization block transfers are not affected by the setting of the 117 BSWP bit. Descriptor transfers are not affected by the setting of the BSWP bit. RDP, RAP, BDP and PCI configuration space accesses are not affected by the setting of the BSWP bit. Address PROM transfers and Expansion ROM accesses are not affected by the setting of the BSWP bit. 13 RES Reserved Location. Written as zero and read as undefined. 12 TXDPOLL Disable Transmit Polling. If TXDPOLL is set, the Buffer Management Unit will disable transmit polling. Likewise, if TXDPOLL is cleared, automatic transmit polling is enabled. If TXDPOLL is set, TDMD bit in CSR0 must be set in order to initiate a manual poll of a transmit descriptor. Transmit descriptor polling will not take place if TXON is reset. Transmit polling will take place following Receive activities. Note that the byte ordering of the PCI bus is defined to be little Endian. BSWP should not be set to 1 when the Am79C978 controller is used in a PCI bus application. This bit is always read/write accessible. BSWP is cleared by H_RESET or S_RESET and is not affected by STOP. 1-0 RES Reserved locations. The default values of these bits are zeros. Writing a 1 to this bit has no effect on device function. If a 1 is written to these bits, then a 1 will be read back. Existing drivers may write a 1 to these bits for compatibility, but new drivers should write a 0 to these bits and should treat the read value as undefined. This bit is always read/write accessible. TXDPOLL is cleared by H_RESET or S_RESET and is unaffected by the STOP bit. 11 CSR4: Test and Features Control Certain bits in CSR4 indicate the cause of an interrupt. The register is designed so that these indicator bits are cleared by writing ones to those bit locations. This means that the software can read CSR4 and write back the value just read to clear the interrupt condition. Bit Name This bit is always read/write accessible. APAD_XMT is cleared by H_RESET or S_RESET and is unaffected by the STOP bit. Description 10 31-16 RES Reserved locations. Written as zeros and read as undefined. 15 RES Reserved location. It is OK for legacy software to write a 1 to this location. This bit must be set back to 0 before setting INIT or STRT bits. This bit is always read/write accessible. This bit is cleared by H_RESET or S_RESET and is unaffected by the STOP bit. 14 118 APAD_XMT Auto Pad Transmit. When set, APAD_XMT enables the automatic padding feature. Transmit frames will be padded to extend them to 64 bytes including FCS. The FCS is calculated for the entire frame, including pad, and appended after the pad field. APAD_XMT will override the programming of the DXMTFCS bit (CSR15, bit 3) and of the ADD_FCS bit (TMD1, bit 29). ASTRP_RCV Auto Strip Receive. When set, ASTRP_RCV enables the automatic pad stripping feature. The pad and FCS fields will be stripped from receive frames and not placed in the FIFO. This bit is always read/write accessible. ASTRP_RCV is cleared by H_RESET or S_RESET and is unaffected by the STOP bit. 9 DMAPLUS Writing and reading from this bit has no effect. DMAPLUS is always set to 1. Am79C978 MFCO Missed Frame Counter Overflow is set by the Am79C978 controller when the Missed Frame Counter (CSR112 and CSR113) has wrapped around. When MFCO is set, INTA is asserted if IENA is 1 and the mask bit MFCOM is 0. This bit is always read/write accessible. MFCO is cleared by the host by writing a 1. Writing a 0 has no effect. MFCO is cleared by H_RESET, S_RESET, or by setting the STOP bit. 8 MFCOM UINTCMD 4 Missed Frame Counter Overflow Mask. If MFCOM is set, the MFCO bit will be masked and unable to set the INTR bit. This bit is always read/write accessible. MFCOM is set to 1 by H_RESET or S_RESET and is not affected by the STOP bit. 7 This bit is always read/write accessible. RCVCCO is cleared by the host by writing a 1. Writing a 0 has no effect. RCVCCO is cleared by H_RESET, S_RESET, or by setting the STOP bit. RCVCCOM Receive Collision Counter Overflow Mask. If RCVCCOM is set, the RCVCCO bit will be masked and unable to set the INTR bit. This bit is always read/write accessible. RCVCCOM is set to 1 by H_RESET or S_RESET and is not affected by the STOP bit. 3 TXSTRT User Interrupt Command. UINTCMD can be used by the host to generate an interrupt unrelated to any network activity. When UINTCMD is set, INTA is asserted if IENA is set to 1. Write a 1 to UINT to clear UINTCMD and stop interrupts. When TXSTRT is set, INTA is asserted if IENA is 1 and the mask bit TXSTRTM is 0. This bit is always read/write accessible. TXSTRT is cleared by the host by writing a 1. Writing a 0 has no effect. TXSTRT is cleared by H_RESET, S_RESET, or by setting the STOP bit. This bit is always read/write accessible. UINTCMD is cleared by H_RESET or S_RESET or by setting the STOP bit. 2 6 5 UINT RCVCCO Transmit Start status is set by the Am79C978 controller whenever it begins transmission of a frame. TXSTRTM User Interrupt. UINT is set by the Am79C978 controller after the host has issued a user interrupt command by setting UINTCMD (CSR4, bit 7) to 1. Transmit Start Mask. If TXSTRTM is set, the TXSTRT bit will be masked and unable to set the INTR bit. This bit is always read/write accessible. TXSTRTM is set to 1 by H_RESET or S_RESET and is not affected by the STOP bit. This bit is always read/write accessible. UINT is cleared by the host by writing a 1. Writing a 0 has no effect. UINT is cleared by H_RESET or S_RESET or by setting the STOP bit. 1-0 Receive Collision Counter Overflow is set by the Am79C978 controller when the Receive Collision Counter (CSR114 and CSR115) has wrapped around. Certain bits in CSR5 indicate the cause of an interrupt. The register is designed so that these indicator bits are cleared by writing ones to those bit locations. This means that the software can read CSR5 and write back the value just read to clear the interrupt condition. When RCVCCO is set, INTA is asserted if IENA is 1 and the mask bit RCVCCOM is 0. Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. RES Reserved locations. Written as zeros and read as undefined. CSR5: Extended Control and Interrupt 1 Am79C978 119 15 TOKINTD Transmit OK Interrupt Disable. If TOKINTD is set to 1, the TINT bit in CSR0 will not be set when a transmission was successful. Only a transmit error will set the TINT bit. TOKINTD has no effect when LTINTEN (CSR5, bit 14) is set to 1. A transmit descriptor with LTINT set to 1 will always cause TINT to be set to 1, independent of the success of the transmission. has no effect. The state of SINT is not affected by clearing any of the PCI Status register bits that get set when a data parity error (DATAPERR, bit 8), master abort (RMABORT, bit 13), or target abort (RTABORT, bit 12) occurs. SINT is cleared by H_RESET or S_RESET and is not affected by setting the STOP bit. 10 SINTE This bit is always read/write accessible. TOKINTD is cleared by H_RESET or S_RESET and is unaffected by STOP. 14 LTINTEN Last Transmit Interrupt Enable. When set to 1, the LTINTEN bit will cause the Am79C978 controller to read bit 28 of TMD1 as LTINT. The setting LTINT will determine if TINT will be set at the end of the transmission. This bit is always read/write accessible. SINTE is set to 0 by H_RESET or S_RESET and is not affected by setting the STOP bit. 9-8 RES Reserved locations. Written as zeros and read as undefined. 7 EXDINT Excessive Deferral Interrupt is set by the Am79C978 controller when the transmitter has experienced Excessive Deferral on a transmit frame, where Excessive Deferral is defined in the ISO 8802-3 (IEEE/ANSI 802.3) standard. This bit is always read/write accessible. LTINTEN is cleared by H_RESET or S_RESET and is unaffected by STOP. 13-12 RES Reserved locations. Written as zeros and read as undefined. 11 SINT System Interrupt is set by the Am79C978 controller when it detects a system error during a bus master transfer on the PCI bus. System errors are data parity error, master abort, or a target abort. The setting of SINT due to data parity error is not dependent on the setting of PERREN (PCI Command register, bit 6). When EXDINT is set, INTA is asserted if the enable bit EXDINTE is 1. This bit is always read/write accessible. EXDINT is cleared by the host by writing a 1. Writing a 0 has no effect. EXDINT is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 6 EXDINTE When SINT is set, INTA is asserted if the enable bit SINTE is 1. Note that the assertion of an interrupt due to SINT is not dependent on the state of the INEA bit, since INEA is cleared by the STOP reset generated by the system error. This bit is always read/write accessible. SINT is cleared by the host by writing a 1. Writing a 0 120 System Interrupt Enable. If SINTE is set, the SINT bit will be able to set the INTR bit. Excessive Deferral Interrupt Enable. If EXDINTE is set, the EXDINT bit will be able to set the INTR bit. This bit is always read/write accessible. EXDINTE is set to 0 by H_RESET and is not affected by S_RESET or setting the STOP bit. 5 Am79C978 MPPLBA Magic Packet Physical Logical Broadcast Accept. If MPPLBA is at its default value of 0, the Am79C978 controller will only detect a Magic Packet frame if the destination address of the packet matches the content of the physical address register (PADR). If MPPLBA is set to 1, the destination address of the Magic Packet frame can be unicast, multicast, or broadcast. Note that the setting of MPPLBA only affects the address detection of the Magic Packet frame. The Magic Packet frame's data sequence must be made up of 16 consecutive physical addresses (PADR[47:0]) regardless of what kind of destination address it has. This bit is OR'ed with the EMPPLBA bit (CSR116, bit 6). This bit is always read/write accessible. MPPLBA is set to 0 by H_RESET or S_RESET and is not affected by setting the STOP bit. 4 MPINT both MPEN and MPMODE are set to 1. This bit is always read/write accessible. MPEN is cleared to 0 by H_RESET or S_RESET and is not affected by setting the STOP bit. 1 MPINTE 0 Magic Packet Interrupt. Magic Packet Interrupt is set by the Am79C978 controller when the device is in Magic Packet mode and the Am79C978 controller receives a Magic Packet frame. When MPINT is set to 1, INTA is asserted if IENA (CSR0, bit 6) and the enable bit MPINTE are set to 1. Magic Packet Interrupt Enable. If MPINTE is set to 1, the MPINT bit will be able to set the INTR bit. This bit is always read/write accessible. MPINT is cleared to 0 by H_RESET or S_RESET and is not affected by setting the STOP bit. 2 MPEN The Am79C978 controller will enter the Magic Packet mode when MPMODE is set to 1 and either PG is asserted or MPEN is set to 1. This bit is always read/write accessible. MPMODE is cleared to 0 by H_RESET or S_RESET and is not affected by setting the STOP bit This bit is always read/write accessible. MPINT is cleared by the host by writing a 1. Writing a 0 has no affect. MPINT is cleared by H_RESET, S_RESET, or by setting the STOP bit. 3 MPMODE Magic Packet Enable. MPEN allows activation of the Magic Packet mode by the host. The Am79C978 controller will enter the Magic Packet mode when Am79C978 SPND Suspend. Setting SPND to 1 will cause the Am79C978 controller to start requesting entrance into suspend mode. The host must poll SPND until it reads back 1 to determine that the Am79C978 controller has entered the suspend mode. Setting SPND to 0 will get the Am79C978 controller out of suspend mode. SPND can only be set to 1 if STOP (CSR0, bit 2) is set to 0. H_RESET, S_RESET, or setting the STOP bit will get the Am79C978 controller out of suspend mode. Requesting entrance into the suspend mode by the host depends on the setting of the FASTSPNDE bit (CSR7, bit 15). Refer to the bit description of the FASTSPNDE bit and the Suspend section in Detailed Functions, Buffer Management Unit for details. In suspend mode, all of the CSR and BCR registers are accessible. As long as the Am79C978 controller is not reset while in suspend mode (by H_RESET, S_RESET, or by setting the STOP bit), no re-initialization of the device is required after the device comes out of suspend mode. The Am79C978 controller will continue at the transmit and receive descriptor ring locations 121 from where it had left, when it entered the suspend mode. This bit is always read/write accessible. SPND is cleared by H_RESET, S_RESET, or by setting the STOP bit. Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15 CSR6: RX/TX Descriptor Table Length Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-12 TLEN Contains a copy of the transmit encoded ring length (TLEN) field read from the initialization block during the Am79C978 controller initialization. This field is written during the Am79C978 initialization routine. Read accessible only when either the STOP or the SPND bit is set. Write operations have no effect and should not be performed. TLEN is only defined after initialization. These bits are unaffected by H_RESET, S_RESET, or STOP. 11-8 RLEN Contains a copy of the receive encoded ring length (RLEN) read from the initialization block during Am79C978 controller initialization. This field is written during the Am79C978 initialization routine. Read accessible only when either the STOP or the SPND bit is set. Write operations have no effect and should not be performed. RLEN is only defined after initialization. These bits are unaffected by H_RESET, S_RESET, or STOP. 7-0 RES Reserved locations. Read as 0s. Write operations are ignored. CSR7: Extended Control and Interrupt 2 Certain bits in CSR7 indicate the cause of an interrupt. The register is designed so that these indicator bits are cleared by writing ones to those bit locations. This means that the software can read CSR7 and write back the value just read to clear the interrupt condition. 122 Am79C978 FASTSPNDE Fast Suspend Enable. When FASTSPNDE is set to 1, the Am79C978 controller performs a fast suspend whenever the SPND bit is set. When a fast suspend is requested, the Am79C978 controller performs a quick entry into the suspend mode. At the time the SPND bit is set, the Am79C978 controller will complete the DMA process of any transmit and/or receive packet that had already begun DMA activity. In addition, any transmit packet that had started transmission will be fully transmitted, and any receive packet that had begun reception will be fully received. However, no additional packets will be transmitted or received and no additional transmit or receive DMA activity will begin. Hence, the Am79C978 controller may enter the suspend mode with transmit and/or receive packets still in the FIFOs or the SRAM. When FASTSPNDE is 0 and the SPND bit is set, the Am79C978 controller may take longer before entering the suspend mode. At the time the SPND bit is set, the Am79C978 controller will complete the DMA process of a transmit packet if it had already begun, and the Am79C978 controller will completely receive a receive packet if it had already begun. Additionally, all transmit packets stored in the transmit FIFOs and the transmit buffer area in the SRAM (if one is enabled) will be transmitted and all receive packets stored in the receive FIFOs, and the receive buffer area in the SRAM (if one is enabled) will be transferred into system memory. Since the FIFO and SRAM contents are flushed, it may take much longer before the Am79C978 controller enters the suspend mode. The amount of time that it takes depends on many factors including the size of the SRAM, bus latency, and network traffic level. When a write to CSR5 is performed with bit 0 (SPND) set to 1, the value that is simultaneously written to FASTSPNDE is used to determine which approach is used to enter suspend mode. This bit is always read/write accessible. RXDPOLL is cleared by H_RESET. RXDPOLL is unaffected by S_RESET or by setting the STOP bit. 11 STINT This bit is always read/write accessible. FASTSPNDE is cleared by H_RESET, S_RESET, or by setting the STOP bit. 14 RES Reserved location. 13 RDMD Receive Demand, when set, causes the Buffer Management Unit to access the Receive Descriptor Ring without waiting for the receive poll-time counter to elapse. If RXON is not enabled, RDMD has no meaning and no receive Descriptor Ring access will occur. When STINT is set to 1, INTA is asserted if the enable bit STINTE is set to 1. This bit is always read/write accessible. STINT is cleared by the host by writing a 1. Writing a 0 has no effect. STINT is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 10 STINTE RDMD is required to be set if the RXDPOLL bit in CSR7 is set. Setting RDMD while RXDPOLL = 0 merely hastens the Am79C978 controller's response to a receive Descriptor Ring Entry. 9 RXDPOLL Software Timer Interrupt Enable. If STINTE is set, the STINT bit will be able to set the INTR bit. This bit is always read/write accessible. STINTE is set to 0 by H_RESET and is not affected by S_RESET or setting the STOP bit This bit is always read/write accessible. RDMD is set by writing a 1. Writing a 0 has no effect. RDMD will be cleared by the Buffer Management Unit when it fetches a receive Descriptor. RDMD is cleared by H_RESET. RDMD is unaffected by S_RESET or by setting the STOP bit. 12 Software Timer Interrupt. The Software Timer interrupt is set by the Am79C978 controller when the Software Timer counts down to 0. The Software Timer will immediately load the STVAL (BCR 31, bits 5-0) into the Software Timer and begin counting down. Receive Disable Polling. If RXDPOLL is set, the Buffer Management Unit will disable receive polling. Likewise, if RXDPOLL is cleared, automatic receive polling is enabled. If RXDPOLL is set, RDMD bit in CSR7 must be set in order to initiate a manual poll of a receive descriptor. Receive Descriptor Polling will not take place if RXON is reset. Am79C978 MREINT PHY Management Read Error Interrupt. The PHY Read Error interrupt is set by the Am79C978 controller to indicate that the currently read register from the PHY is invalid, the contents of BCR34 are incorrect, and the operation should be performed again. The indication of an incorrect read comes from the internal PHY. When MREINT is set to 1, INTA is asserted if the enable bit MREINTE is set to 1. This bit is always read/write accessible. MREINT is cleared by the host by writing a 1. Writing a 0 has no effect. MREINT is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 123 8 MREINTE PHY Management Read Error Interrupt Enable. If MREINTE is set, the MREINT bit will be able to set the INTR bit. When MCCINT is set to 1, INTA is asserted if the enable bit MCCINTE is set to 1. This bit is always read/write accessible. MCCINT is cleared by the host by writing a 1. Writing a 0 has no effect. MCCINT is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. This bit is always read/write accessible. MREINTE is set to 0 by H_RESET and is not affected by S_RESET or setting the STOP bit 7 MAPINT PHY Management Auto-Poll Interrupt. The PHY Auto-Poll interrupt is set by the Am79C978 controller to indicate that the currently read status does not match the stored previous status indicating a change in state for the internal PHY. A change in the AutoPoll Access Method (BCR32, Bit 11) will reset the shadow register and will not cause an interrupt on the first access from the Auto-Poll section. Subsequent accesses will generate an interrupt if the shadow register and the read register produce differences. 4 MCCINTE When MAPINT is set to 1, INTA is asserted if the enable bit MAPINTE is set to 1. This bit is always read/write accessible. MAPINT is cleared by the host by writing a 1. Writing a 0 has no effect. MAPINT is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 6 MAPINTE This bit is always read/write accessible. MCCINTE is set to 0 by H_RESET and is not affected by S_RESET or setting the STOP bit. 3 PHY Auto-Poll Interrupt Enable. If MAPINTE is set, the MAPINT bit will be able to set the INTR bit. This bit is always read/write accessible. MAPINTE is set to 0 by H_RESET and is not affected by S_RESET or setting the STOP bit. 5 124 MCCINT PHY Management Command Complete Interrupt Enable. If MCCINTE is set to 1, the MCCINT bit will be able to set the INTR bit when the host reads or writes to the internal PHY Data Port (BCR34) only. Internal PHY Management Commands will not generate an interrupt. For instance Auto-Poll state machine generated management frames will not generate an interrupt upon completion unless there is a compare error which gets reported through the MAPINT (CSR7, bit 6) interrupt or the MCCIINTE is set to 1. PHY Management Command Complete Interrupt. The PHY Management Command Complete Interrupt is set by the Am79C978 controller when a read or write operation to the internal PHY Data Port (BCR34) is complete. Am79C978 MCCIINT PHY Management Command Complete Internal Interrupt. The PHY Management Command Complete Interrupt is set by the Am79C978 controller when a read or write operation on the internal PHY management port is complete from an internal operation. Examples of internal operations are Auto-Poll or PHY Management Port generated management frames. These are normally hidden to the host. When MCCIINT is set to 1, INTA is asserted if the enable bit MCCINTE is set to 1. This bit is always read/write accessible. MCCIINT is cleared by the host by writing a 1. Writing a 0 has no effect. MCCIINT is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 2 MCCIINTE PHY Management Command Complete Internal Interrupt Enable. If MCCIINTE is set to 1, the MCCIINT bit will be able to set the INTR bit when the internal state machines generate management frames. For instance, when MCCIINTE is set to 1 and the Auto-Poll state machine generates a management frame, the MCCIINT will set the INTR bit upon completion of the management frame regardless of the comparison outcome. This bit is always read/write accessible. MCCIINTE is set to 0 by H_RESET and is not affected by S_RESET or setting the STOP bit. 1 MIIPDTINT PHY Detect Transition Interrupt. The PHY Detect Transition Interrupt is set by the Am79C978 controller whenever the MIIPD bit (BCR32, bit 14) transitions from 0 to 1 or vice versa. This bit is always read/write accessible. MIIPDTINT is cleared by the host by writing a 1. Writing a 0 has no effect. MIIPDTINT is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 0 MIIPDTINTE PHY Detect Transition Interrupt Enable. If MIIPDTINTE is set to 1, the MIIPDTINT bit will be able to set the INTR bit. This bit is always read/write accessible. MIIPDTINTE is set to 0 by H_RESET and is not affected by S_RESET or setting the STOP bit. is undefined until loaded from the initialization block after the INIT bit in CSR0 has been set or a direct register write has been performed on this register. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR9: Logical Address Filter 1 Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 LADRF[31:16] Logical Address Filter, LADRF[31:16]. The content of this register is undefined until loaded from the initialization block after the INIT bit in CSR0 has been set or a direct register write has been performed on this register. These bits are These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR10: Logical Address Filter 2 Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 LADRF[47:32] Logical Address Filter, LADRF[47:32]. The content of this register is undefined until loaded from the initialization block after the INIT bit in CSR0 has been set or a direct register write has been performed on this register. CSR8: Logical Address Filter 0 Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 These bit are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. LADRF[15:0] Logical Address Filter, LADRF[15:0]. The content of this register Am79C978 125 CSR11: Logical Address Filter 3 Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 15-0 LADRF[63:48] Logical Address Filter, LADRF[63:48]. The content of this register is undefined until loaded from the initialization block after the INIT bit in CSR0 has been set or a direct register write has been performed on this register. PADR[31:16] Physical Address Register, PADR[31:16]. The contents of this register are loaded from the EEPROM after H_RESET or by an EEPROM read command (PRGAD, BCR19, bit 14). If the EEPROM is not present, the contents of this register are undefined. This register can also be loaded from the initialization block after the INIT bit in CSR0 has been set or a direct register write has been performed on this register. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR12: Physical Address Register 0 Note: Bits 15-0 in this register are programmable through the EEPROM. Bit 31-16 15-0 Name RES Description Reserved locations. Written as zeros and read as undefined. PADR[15:0] Physical Address Register, PADR[15:0]. The contents of this register are loaded from the EEPROM after H_RESET or by an EEPROM read command (PRGAD, BCR19, bit 14). If the EEPROM is not present, the contents of this register are undefined. CSR14: Physical Address Register 2 Note: Bits 15-0 in this register are programmable through the EEPROM. Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 This register can also be loaded from the initialization block after the INIT bit in CSR0 has been set or a direct register write has been performed on this register. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR13: Physical Address Register 1 Note: Bits 15-0 in this register are programmable through the EEPROM. 126 Am79C978 PADR[47:32] Physical Address Register, PADR[47:32]. The contents of this register are loaded from the EEPROM after H_RESET or by an EEPROM read command (PRGAD, BCR19, bit 14). If the EEPROM is not present, the contents of this register are undefined. This register can also be loaded from the initialization block after the INIT bit in CSR0 has been set or a direct register write has been performed on this register. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR15: Mode This register's fields are loaded during the Am79C978 controller initialization routine with the corresponding Initialization Block values, or when a direct register write has been performed on this register. Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15 PROM Promiscuous Mode. When PROM = 1, all incoming receive frames are accepted. SPND bit is set. Cleared by H_RESET or S_RESET and is unaffected by STOP. 6 INTL This bit is read/write accessible only when either the STOP or the SPND bit is set. 5 DRTY This bit is read/write accessible only when either the STOP or the SPND bit is set. 14 DRCVBC Disable Receive Broadcast. When set, disables the Am79C978 controller from receiving broadcast messages. Used for protocols that do not support broadcast addressing, except as a function of multicast. DRCVBC is cleared by activation of H_RESET or S_RESET (broadcast messages will be received) and is unaffected by STOP. DRCVPA 4 Disable Receive Physical Address. When set, the physical address detection (Station or node ID) of the Am79C978 controller will be disabled. Frames addressed to the nodes individual physical address will not be recognized. This bit is read/write accessible only when either the STOP or the SPND bit is set. 12-9 RES Disable Retry. When DRTY is set to 1, the Am79C978 controller will attempt only one transmission. In this mode, the device will not protect the first 64 bytes of frame data in the Transmit FIFO from being overwritten, because automatic retransmission will not be necessary. When DRTY is set to 0, the Am79C978 controller will attempt 16 transmissions before signaling a retry error. This bit is read/write accessible only when either the STOP or the SPND bit is set. This bit is read/write accessible only when either the STOP or the SPND bit is set. 13 Internal Loopback. See the description of LOOP (CSR15, bit 2). FCOLL Force Collision. This bit allows the collision logic to be tested. The Am79C978 controller must be in internal loopback for FCOLL to be valid. If FCOLL = 1, a collision will be forced during loopback transmission attempts, which will result in a Retry Error. If FCOLL = 0, the Force Collision logic will be disabled. FCOLL is defined after the initialization block is read. This bit is read/write accessible only when either the STOP or the SPND bit is set. 3 Reserved locations. Written as zeros and read as undefined. 8-7 PORTSEL[1:0] Port Select bits allow for software controlled selection of the network medium. The only legal values for this field is 11. This bit is read/write accessible only when either the STOP or the Am79C978 DXMTFCS Disable Transmit CRC (FCS). When DXMTFCS is set to 0, the transmitter will generate and append an FCS to the transmitted frame. When DXMTFCS is set to 1, no FCS is generated or sent with the transmitted frame. DXMTFCS is overridden when ADD_FCS and ENP bits are set in TMD1. When the APAD_XMT bit (CSR4, bit11) is set to 1, the setting of DXMTFCS has no effect. 127 If DXMTFCS is set and ADD_FCS is clear for a particular frame, no FCS will be generated. If ADD_FCS is set for a particular frame, the state of DXMTFCS is ignored and a FCS will be appended on that frame by the transmit circuitry. See also the ADD_FCS bit in TMD1. This bit was called DTCR in the LANCE (Am7990) device. This bit is read/write accessible only when either the STOP or the SPND bit is set. 2 LOOP Loopback Enable allows the Am79C978 controller to operate in full-duplex mode for test purposes. The setting of the fullduplex control bits in BCR9 have no effect when the device operates in loopback mode. When LOOP = 1, loopback is enabled. In combination with INTL and MIIILP, various loopback modes are defined as follows in Table 30. ing the Receive Descriptor Ring and, therefore, all receive frame data are ignored. DRX = 0 will set RXON bit (CSR0 bit 5) if STRT (CSR0 bit 1) is asserted. This bit is read/write accessible only when either the STOP or the SPND bit is set. CSR16: Initialization Block Address Lower Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 IADRL This register is an alias of CSR1. These bits are read/write accessible only when either the STOP or the SPND bit is set. CSR17: Initialization Block Address Upper Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 IADRH This register is an alias of CSR2. Table 30. Loopback Configuration LOOP INTL MIIILP 0 0 0 Normal Operation 0 0 1 Internal Loop 1 0 0 External Loop These bits are read/write accessible only when either the STOP or the SPND bit is set. Function CSR18: Current Receive Buffer Address Lower Refer to Loopback Operation section for more details. This bit is read/write accessible only when either the STOP or the SPND bit is set. LOOP is cleared by H_RESET or S_RESET and is unaffected by STOP. 1 DTX Disable Transmit results in Am79C978 controller not accessing the Transmit Descriptor Ring and, therefore, no transmissions are attempted. DTX = 0, will set TXON bit (CSR0 bit 4) if STRT (CSR0 bit 1) is asserted. This bit is read/write accessible only when either the STOP or the SPND bit is set. 0 128 DRX Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 CRBAL Contains the lower 16 bits of the current receive buffer address at which the Am79C978 controller will store incoming frame data. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR19: Current Receive Buffer Address Upper Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. Disable Receiver results in the Am79C978 controller not access- Am79C978 15-0 CRBAU Contains the upper 16 bits of the current receive buffer address at which the Am79C978 controller will store incoming frame data. or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR23: Next Receive Buffer Address Upper These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR20: Current Transmit Buffer Address Lower Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 CXBAL Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 NRBAU Contains the upper 16 bits of the next receive buffer address to which the Am79C978 controller will store incoming frame data. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. Contains the lower 16 bits of the current transmit buffer address from which the Am79C978 controller is transmitting. CSR24: Base Address of Receive Ring Lower These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR21: Current Transmit Buffer Address Upper Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 CXBAU Contains the upper 16 bits of the current transmit buffer address from which the Am79C978 controller is transmitting. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 BADRL Contains the lower 16 bits of the base address of the Receive Ring. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR25: Base Address of Receive Ring Upper Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 BADRU Contains the upper 16 bits of the base address of the Receive Ring. CSR22: Next Receive Buffer Address Lower Bit Name Description These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 NRBAL Contains the lower 16 bits of the next receive buffer address to which the Am79C978 controller will store incoming frame data. CSR26: Next Receive Descriptor Address Lower Bit Name Description These bits are read/write accessible only when either the STOP 31-16 RES Reserved locations. Written as zeros and read as undefined. Am79C978 129 15-0 NRDAL Contains the lower 16 bits of the next receive descriptor address pointer. CSR30: Base Address of Transmit Ring Lower Bit Name Description These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 BADXL Contains the lower 16 bits of the base address of the Transmit Ring. CSR27: Next Receive Descriptor Address Upper These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 NRDAU Contains the upper 16 bits of the next receive descriptor address pointer. CSR31: Base Address of Transmit Ring Upper Bit Name Description These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 BADXU Contains the upper 16 bits of the base address of the Transmit Ring. CSR28: Current Receive Descriptor Address Lower These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 CRDAL Contains the lower 16 bits of the current receive descriptor address pointer. CSR32: Next Transmit Descriptor Address Lower Bit Name Description These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 NXDAL Contains the lower 16 bits of the next transmit descriptor address pointer. CSR29: Current Receive Descriptor Address Upper These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 CRDAU Contains the upper 16 bits of the current receive descriptor address pointer. CSR33: Next Transmit Descriptor Address Upper Bit Name Description These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 NXDAU Contains the upper 16 bits of the next transmit descriptor address pointer. 130 Am79C978 These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR34: Current Transmit Descriptor Address Lower Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 CXDAL CSR35: Current Transmit Descriptor Address Upper Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. CXDAU CSR36: Next Next Receive Descriptor Address Lower Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. NNRDAL Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 NNRDAU Contains the upper 16 bits of the next next receive descriptor address pointer. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR38: Next Next Transmit Descriptor Address Lower Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 NNXDAL Contains the lower 16 bits of the next next transmit descriptor address pointer. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. Contains the upper 16 bits of the current transmit descriptor address pointer. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. 15-0 Bit Contains the lower 16 bits of the current transmit descriptor address pointer. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. 15-0 CSR37: Next Next Receive Descriptor Address Upper CSR39: Next Next Transmit Descriptor Address Upper Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 NNXDAU Contains the upper 16 bits of the next next transmit descriptor address pointer. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. Contains the lower 16 bits of the next next receive descriptor address pointer. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR40: Current Receive Byte Count Bit 31-16 Am79C978 Name RES Description Reserved locations. Written as zeros and read as undefined. 131 15-12 11-0 RES CRBC Reserved locations. Read and written as zeros. Current Receive Byte Count. This field is a copy of the BCNT field of RMD1 of the current receive descriptor. CSR43: Current Transmit Status Bit Name 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 Current Transmit Status. This field is a copy of bits 31-16 of TMD1 of the current transmit descriptor. CXST These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR41: Current Receive Status Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 CRST Current Receive Status. This field is a copy of bits 31-16 of RMD1 of the current receive descriptor. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR44: Next Receive Byte Count Bit Name Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-12 RES Reserved locations. Read and written as zeros. 11-0 CXBC Current Transmit Byte Count. This field is a copy of the BCNT field of TMD1 of the current transmit descriptor. Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-12 RES Reserved locations. Read and written as zeros. 11-0 Next Receive Byte Count. This field is a copy of the BCNT field of RMD1 of the next receive descriptor. NRBC CSR42: Current Transmit Byte Count Bit Description These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR45: Next Receive Status Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 Next Receive Status. This field is a copy of bits 31-16 of RMD1 of the next receive descriptor. NRST These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR46: Transmit Poll Time Counter Bit Name 31-16 RES 132 Am79C978 Description Reserved locations. Written as zeros and read as undefined. 15-0 TXPOLL Transmit Poll Time Counter. This counter is incremented by the Am79C978 controller microcode and is used to trigger the transmit descriptor ring polling operation of the Am79C978 controller. overwritten with the desired user value. If the user does not use the standard initialization procedure (standard implies use of an initialization block in memory and setting the INIT bit of CSR0), but instead chooses to write directly to each of the registers that are involved in the INIT operation, then it is imperative that the user also writes all zeros to CSR47 as part of the alternative initialization sequence. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR47: Transmit Polling Interval Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 TXPOLLINT Transmit Polling Interval. This register contains the time that the Am79C978 controller will wait between successive polling operations. The TXPOLLINT value is expressed as the two's complement of the desired interval, where each bit of TXPOLLINT represents 1 clock period of time. TXPOLLINT[3:0] are ignored. (TXPOLLINT[16] is implied to be a one, so TXPOLLINT[15] is significant and does not represent the sign of the two's complement TXPOLLINT value.) The default value of this register is 0000h. This corresponds to a polling interval of 65,536 clock periods (1.966 ms when CLK = 33 MHz). The TXPOLLINT value of 0000h is created during the microcode initialization routine and, therefore, might not be seen when reading CSR47 after H_RESET or S_RESET. If the user desires to program a value for POLLINT other than the default, then the correct procedure is to first set INIT only in CSR0. Then, when the initialization sequence is complete, the user must set STOP (CSR0, bit 2). Then the user may write to CSR47 and then set STRT in CSR0. In this way, the default value of 0000h in CSR47 will be These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR48: Receive Poll Time Counter Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 Receive Poll Time Counter. This counter is incremented by the Am79C978 controller microcode and is used to trigger the receive descriptor ring polling operation of the Am79C978 controller. RXPOLL These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR49: Receive Polling Interval Bit Name 31-16 RES 15-0 Am79C978 Description Reserved locations. Written as zeros and read as undefined. RXPOLLINT Receive Polling Interval. This register contains the time that the Am79C978 controller will wait between successive polling operations. The RXPOLLINT value is expressed as the two's complement of the desired interval, where each bit of RXPOLLINT represents approximately one clock time period. RXPOLLINT[3:0] are ignored. (RXPOL- 133 LINT[16] is implied to be a 1, so RXPOLLINT[15] is significant and does not represent the sign of the two's complement RXPOLLINT value.) 10 APERREN The default value of this register is 0000h. This corresponds to a polling interval of 65,536 clock periods (1.966 ms when CLK = 33 MHz). The RXPOLLINT value of 0000h is created during the microcode initialization routine and, therefore, might not be seen when reading CSR49 after H_RESET or S_RESET. If the user desires to program a value for RXPOLLINT other than the default, then the correct procedure is to first set INIT only in CSR0. Then, when the initialization sequence is complete, the user must set STOP (CSR0, bit 2). Then the user may write to CSR49 and set STRT in CSR0. In this way, the default value of 0000h in CSR47 will be overwritten with the desired user value. If the user does not use the standard initialization procedure (standard implies use of an initialization block in memory and setting the INIT bit of CSR0), but instead chooses to write directly to each of the registers that are involved in the INIT operation, it is imperative that the user also writes all zeros to CSR49 as part of the alternative initialization sequence. APERREN does not affect the reporting of address parity errors or data parity errors that occur when the Am79C978 controller is the target of the transfer. Read anytime, write accessible only when either the STOP or the SPND bit is set. APERREN is cleared by H_RESET and is not affected by S_RESET or STOP. 9 RES Reserved location. Written as zero and read as undefined. 8 SSIZE32 Software Size 32 bits. When set, this bit indicates that the Am79C978 controller utilizes 32bit software structures for the initialization block and the transmit and receive descriptor entries. When cleared, this bit indicates that the Am79C978 controller utilizes 16-bit software structures for the initialization block and the transmit and receive descriptor entries. In this mode, the Am79C978 controller is backwards compatible with the Am7990 LANCE and Am79C960 PCnet-ISA controllers. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR58: Software Style This register is an alias of the location BCR20. Accesses to and from this register are equivalent to accesses to BCR20. Bit Name 31-11 RES 134 Advanced Parity Error Handling Enable. When APERREN is set to 1, the BPE bits (RMD1 and TMD1, bit 23) start having a meaning. BPE will be set in the descriptor associated with the buffer that was accessed when a data parity error occurred. Note that since the advanced parity error handling uses an additional bit in the descriptor, SWSTYLE (bits 7-0 of this register) must be set to 2 or 3 to program the Am79C978 controller to use 32-bit software structures. Description Reserved locations. Written as zeros and read as undefined. Am79C978 The value of SSIZE32 is determined by the Am79C978 controller according to the setting of the Software Style (SWSTYLE, bits 7-0 of this register). Read accessible always. SSIZE32 is read only; write operations will be ignored. SSIZE32 will be cleared after H_RESET (since SWSTYLE defaults to 0) and is not affected by S_RESET or STOP. If SSIZE32 is reset, then bits IADR[31:24] of CSR2 will be used to generate values for the upper 8 bits of the 32-bit address bus during master accesses initiated by the Am79C978 controller. This action is required because the 16-bit software structures specified by the SSIZE32 = 0 setting will yield only 24 bits of address for the Am79C978 controller bus master accesses. defined width for I/O resources. I/O resource width is determined by the state of the DWIO bit (BCR18, bit 7). 7-0 SWSTYLE If SSIZE32 is set, then the software structures that are common to the Am79C978 controller and the host system will supply a full 32 bits for each address pointer that is needed by the Am79C978 controller for performing master accesses. Software Style register. The value in this register determines the style of register and memory resources that shall be used by the Am79C978 controller. The Software Style selection will affect the interpretation of a few bits within the CSR space, the order of the descriptor entries and the width of the descriptors and initialization block entries. All Am79C978 controller CSR bits and BCR bits and all descriptor, buffer, and initialization block entries not cited in Table 31 are unaffected by the Software Style selection and are, therefore, always fully functional as specified in the CSR and BCR sections. The value of the SSIZE32 bit has no effect on the drive of the upper 8 address bits. The upper 8 address pins are always driven, regardless of the state of the SSIZE32 bit. These bits are read/write accessible only when either the STOP or the SPND bit is set. The SWSTYLE register will contain the value 00h following H_RESET and will be unaffected by S_RESET or STOP. Note that the setting of the SSIZE32 bit has no effect on the Table 31. Software Styles SWSTYLE [7:0] Style Name SSIZE32 00h LANCE/PCnet-ISA controller 0 01h RES 1 02h PCnet-PCI controller 1 03h All Other PCnet-PCI controller RES 1 Undefined Am79C978 Initialization Block Entries Descriptor Ring Entries 16-bit software structures, 16-bit software structures, non-burst or burst access non-burst access only RES RES 32-bit software structures, 32-bit software structures, non-burst or burst access non-burst access only 32-bit software structures, 32-bit software structures, non-burst or burst access non-burst or burst access Undefined Undefined 135 CSR60: Previous Transmit Descriptor Address Lower Bit Name CSR63: Previous Transmit Status Bit 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 Contains the lower 16 bits of the previous transmit descriptor address pointer. The Am79C978 controller has the capability to stack multiple transmit frames. PXDAL These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. Name Reserved locations. Written as zeros and read as undefined. 15-0 Previous Transmit Status. This field is a copy of bits 31-16 of TMD1 of the previous transmit descriptor. PXST These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR64: Next Transmit Buffer Address Lower Name Reserved locations. Written as zeros and read as undefined. 15-0 Contains the upper 16 bits of the previous transmit descriptor address pointer. The Am79C978 controller has the capability to stack multiple transmit frames. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. Reserved locations. Written as zeros and read as undefined. 15-0 Contains the lower 16 bits of the next transmit buffer address from which the Am79C978 controller will transmit an outgoing frame. NXBAL These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR65: Next Transmit Buffer Address Upper Bit Name Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-12 RES Reserved locations. 11-0 Previous Transmit Byte Count. This field is a copy of the BCNT field of TMD1 of the previous transmit descriptor. PXBC Reserved locations. Written as zeros and read as undefined. 15-0 Contains the upper 16 bits of the next transmit buffer address from which the Am79C978 controller will transmit an outgoing frame. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. 136 Description 31-16 RES CSR62: Previous Transmit Byte Count Bit Description 31-16 RES Description 31-16 RES PXDAU Description 31-16 RES Bit CSR61: Previous Transmit Descriptor Address Upper Bit Name Description Am79C978 NXBAU These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR66: Next Transmit Byte Count Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-12 RES Reserved locations. Read and written as zeros. 11-0 NXBC These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. Next Transmit Byte Count. This field is a copy of the BCNT field of TMD1 of the next transmit descriptor. CSR74: Transmit Ring Counter Bit Name 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 Transmit Ring Counter location. Contains a two's complement binary number used to number the current transmit descriptor. This counter interprets the value in CSR78 as pointing to the first descriptor. A counter value of zero corresponds to the last descriptor in the ring. XMTRC These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR67: Next Transmit Status Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 Next Transmit Status. This field is a copy of bits 31-16 of TMD1 of the next transmit descriptor. NXST These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. 7-0 RES These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR76: Receive Ring Length Bit Name 15-0 Receive Ring Length. Contains the two's complement of the receive descriptor ring length. This register is initialized during the Am79C978 controller's initialization routine based on the value in the RLEN field of the initialization block. However, this register can be manually altered. The actual receive ring length is defined by the current value in this register. The ring length can be defined as any value from 1 to 65535. Description Reserved locations. Written as zeros and read as undefined. 15-0 Receive Ring Counter location. Contains a two's complement binary number used to number the current receive descriptor. This counter interprets the value in CSR76 as pointing to the first descriptor. A counter value of zero corresponds to the last descriptor in the ring. RCVRC Description Reserved locations. Written as zeros and read as undefined. Reserved locations. Read and written as zeros. Accessible only when either the STOP or the SPND bit is set. 31-16 RES Name 31-16 RES CSR72: Receive Ring Counter Bit Description Am79C978 RCVRL These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. 137 CSR78: Transmit Ring Length Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 Transmit Ring Length. Contains the two's complement of the transmit descriptor ring length. This register is initialized during the Am79C978 controller's initialization routine based on the value in the TLEN field of the initialization block. However, this register can be manually altered. The actual transmit ring length is defined by the current value in this register. The ring length can be defined as any value from 1 to 65535. XMTRL work interface is operating in fullduplex mode, receive DMA will be requested as soon as either the RCVFW threshold is reached or a complete valid receive frame is detected (regardless of length). When the FDRPAD (BCR9, bit 2) is set and the Am79C978 controller is in full-duplex mode, in order for receive DMA to be performed for a new frame at least 64 bytes must have been received. This effectively disables the runt packet accept feature in full duplex. When operating in the NO-SRAM mode (no SRAM enabled), the Bus Receive FIFO and the MAC Receive operate like a single FIFO and the watermark value selected by RCVFW[1:0] sets the number of bytes that must be present in the FIFO before receive DMA is requested. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. When operating with the SRAM, the Bus Receive FIFO, and the MAC Receive FIFO operate independently on the bus side and MAC side of the SRAM, respectively. In this case, the watermark value set by RCVFW[1:0] sets the number of bytes that must be present in the Bus Receive FIFO only. See Table 32. CSR80: DMA Transfer Counter and FIFO Threshold Control Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-14 RES Reserved locations. Written as zeros and read as undefined. 13-12 RCVFW[1:0] Receive FIFO Watermark. RCVFW controls the point at which receive DMA is requested in relation to the number of received bytes in the Receive FIFO. RCVFW specifies the number of bytes which must be present (once the frame has been verified as a non-runt) before receive DMA is requested. Note, however, that if the network interface is operating in half-duplex mode, in order for receive DMA to be performed for a new frame at least 64 bytes must have been received. This effectively avoids having to react to receive frames which are runts or suffer a collision during the slot time (512 bit times). If the Runt Packet Accept feature is enabled or if the net138 Table 32. Receive Watermark Programming RCVFW[1:0] Bytes Received 00 16 01 64 10 112 11 Reserved These bits are read/write accessible only when either the STOP or the SPND bit is set. RCVFW[1:0] is set to a value of 01b (64 bytes) after H_RESET or S_RESET and is unaffected by STOP. 11-10 XMTSP[1:0] Transmit Start Point. XMTSP controls the point at which preamble transmission attempts to commence in relation to the number of bytes written to the MAC Transmit FIFO for the current Am79C978 transmit frame. When the entire frame is in the MAC Transmit FIFO, transmission will start regardless of the value in XMTSP. If the network interface is operating in half-duplex mode, regardless of XMTSP, the FIFO will not internally overwrite its data until at least 64 bytes (or the entire frame if shorter than 64 bytes) have been transmitted onto the network. This ensures that for collisions within the slot time window, transmit data need not be rewritten to the Transmit FIFO, and retries will be handled autonomously by the MAC. If the Disable Retry feature is enabled, or if the network is operating in full-duplex mode, the Am79C978 controller can overwrite the beginning of the frame as soon as the data is transmitted, because no collision handling is required in these modes. Table 33. Transmit Start Point Programming XMTSP[1:0] SRAM_SIZE Bytes Written 00 0 20 01 0 64 10 0 128 11 0 220 max 00 >0 36 01 >0 64 10 >0 128 11 >0 Full Packet >0 Full Packet when NOUFLO bit is set XX 9-8 Note that when the SRAM is being used, if the NOUFLO bit (BCR18, bit 11) is set to 1, there is the additional restriction that the complete transmit frame must be DMA'd into the Am79C978 controller and reside within a combination of the Bus Transmit FIFO, the SRAM, and the MAC Transmit FIFO. When the SRAM is used and SRAM_SIZE > 0, there is a restriction that the number of bytes written is a combination of bytes written into the Bus Transmit FIFO and the MAC Transmit FIFO. The Am79C978 controller supports a mode that will wait until a full packet is available before commencing with the transmission of preamble. This mode is useful in a system where high latencies cannot be avoided. See Table 33. These bits are read/write accessible only when either the STOP or the SPND bit is set. XMTSP is set to a value of 01b (64 bytes) after H_RESET or S_RESET and is unaffected by STOP. Am79C978 XMTFW[1:0] Transmit FIFO Watermark. XMTFW specifies the point at which transmit DMA is requested, based upon the number of bytes that could be written to the Transmit FIFO without FIFO overflow. Transmit DMA is requested at any time when the number of bytes specified by XMTFW could be written to the FIFO without causing Transmit FIFO overflow and the internal microcode engine has reached a point where the Transmit FIFO is checked to determine if DMA servicing is required. When operating in the NO-SRAM mode (no SRAM enabled) and SRAM_SIZE is set to 0, the Bus Transmit FIFO and the MAC Transmit FIFO operate like a single FIFO and the watermark value selected by XMTFW[1:0] sets the number of FIFO byte locations that must be available in the FIFO before receive DMA is requested. When operating with the SRAM, the Bus Transmit FIFO and the MAC Transmit FIFO operate independently on the bus side and MAC side of the SRAM, respectively. In this case, the watermark value set by XMTFW[1:0] sets the number of FIFO byte locations that must be available in the Bus Transmit FIFO. See Table 34 139 . 15-0 Table 34. DMABAL Transmit Watermark Programming XMTFW[1:0] Bytes Available 00 16 01 64 10 108 11 Reserved These bits are read/write accessible only when either the STOP or the SPND bit is set. XMTFW is set to a value of 00b (16 bytes) after H_RESET or S_RESET and is unaffected by STOP. 7-0 DMATC[7:0] DMA Transfer Counter. Writing and reading to this field has no effect. Use MAX_LAT and MIN_GNT in the PCI configuration space. CSR82: Transmit Descriptor Address Pointer Lower Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 Contains the lower 16 bits of the transmit descriptor address corresponding to the last buffer of the previous transmit frame. If the previous transmit frame did not use buffer chaining, then TXDAPL contains the lower 16 bits of the previous frame's transmit descriptor address. TXDAPL When both the STOP or SPND bits are cleared, this register is updated by the Am79C978 controller immediately before a transmit descriptor write. Read accessible always. Write accessible through the PXDAL bits (CSR60) when the STOP or SPND bit is set. TXDAPL is set to 0 by H_RESET and are unaffected by S_RESET or STOP. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR85: DMA Address Register Upper Bit Name 31-16 RES 140 Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 This register contains the upper 16 bits of the address of system memory for the current DMA cycle. The Bus Interface Unit controls the Address Register by issuing increment commands to increment the memory address for sequential operations. The DMABAU register is undefined until the first Am79C978 controller DMA operation. DMABAU These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR86: Buffer Byte Counter Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-12 RES Reserved. Read and written with ones. 11-0 DMA Byte Count Register. Contains the two's complement of the current size of the remaining transmit or receive buffer in bytes. This register is incremented by the Bus Interface Unit. The CSR84: DMA Address Register Lower Bit This register contains the lower 16 bits of the address of system memory for the current DMA cycle. The Bus Interface Unit controls the Address Register by issuing increment commands to increment the memory address for sequential operations. The DMABAL register is undefined until the first Am79C978 controller DMA operation. Description Reserved locations. Written as zeros and read as undefined. Am79C978 DMABC DMABC register is undefined until written. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR89: Chip ID Register Upper Bit Name 31-16 RES Reserved locations. Read as undefined. 15-12 VER Version. This 4-bit pattern is silicon-revision dependent. CSR88: Chip ID Register Lower Bit Name 31-28 VER Read accessible only when either the STOP or the SPND bit is set. VER is read only. Write operations are ignored. Description Version. This 4-bit pattern is silicon-revision dependent. 11-0 PARTIDU Read accessible only when either the STOP or the SPND bit is set. VER is read only. Write operations are ignored. 27-12 PARTID Read accessible only when either the STOP or the SPND bit is set. PARTID is read only. Write operations are ignored. 11-1 MANFID CSR92: Ring Length Conversion Bit Name Reserved locations. Written as zeros and read as undefined. 15-0 Ring Length Conversion Register. This register performs a ring length conversion from an encoded value as found in the initialization block to a two's complement value used for internal counting. By writing bits 15-12 with an encoded ring length, a two's complemented value is read. The RCON register is undefined until written. RCON Note that this code is not the same as the Vendor ID in the PCI configuration space. These bits are read/write accessible only when either the STOP or the SPND bit is set. These bits are unaffected by H_RESET, S_RESET, or STOP. CSR100: Bus Timeout Bit 0 ONE Description 31-16 RES Manufacturer ID. The 11-bit manufacturer code for AMD is 00000000001b. This code is per the JEDEC Publication 106-A. Read accessible only when either the STOP or the SPND bit is set. VER is read only. MANFID is read only. Write operations are ignored. Upper 12 bits of the Am79C978 controller part number, i.e., 0010 0110 0010b (262h). Read accessible only when either the STOP or the SPND bit is set. VER is read only. PARTIDU is read only. Write operations are ignored. Part number. The 16-bit code for the Am79C978 controller is 0010 0110 0010 0110 (2626h). This register is exactly the same as the Device ID register in the JTAG description. However, this part number is different from that stored in the Device ID register in the PCI configuration space. Description Name Description Always a logic 1. Read accessible only when either the STOP or the SPND bit is set. VER is read only. ONE is read only. Write operations are ignored. 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 This register contains the value of the longest allowable bus latency (interval between assertion of REQ and assertion of GNT) that a Am79C978 MERRTO 141 system may insert into an Am79C978 controller master transfer. If this value of bus latency is exceeded, then a MERR will be indicated in CSR0, bit 11, and an interrupt may be generated, depending upon the setting of the MERRM bit (CSR3, bit 11) and the IENA bit (CSR0, bit 6). The value in this register is interpreted as the unsigned number of bus clock periods divided by two, (i.e., the value in this register is given in 0.1 ms increments). For example, the value 0600h (1536 decimal) will cause a MERR to be indicated after 153.6 ms of bus latency. A value of 0 will allow an infinitely long bus latency, i.e., bus timeout error will never occur. These bits are read/write accessible only when either the STOP or the SPND bit is set. This register is set to 0600h by H_RESET or S_RESET and is unaffected by STOP. sions encountered by the receiver since the last reset of the counter. RCC will roll over to a count of 0 from the value 65535. The RCVCCO bit of CSR4 (bit 5) will be set each time that this occurs. These bits are read accessible always. RCC is read only, write operations are ignored. RCC is cleared by H_RESET or S_RESET, or by setting the STOP bit. CSR116: OnNow Power Mode Register Note: Bits 15-0 in this register are programmable through the EEPROM. Bit Name 31-16 RES Name Reserved locations. Written as zeros and read as undefined. 15-0 Missed Frame Count. Indicates the number of missed frames. MFC These bits are read/write accessible only when either the STOP bit or the SPND bit is set. Cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. Description 31-16 RES 9 LCDET MFC will roll over to a count of 0 from the value 65535. The MFCO bit of CSR4 (bit 8) will be set each time that this occurs. Read accessible always. MFC is read only, write operations are ignored. MFC is cleared by H_RESET, or S_RESET or by setting the STOP bit. Name This bit is always read/write accessible. 8 Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 Receive Collision Count. Indicates the total number of colli- 142 RCC Link Change Detected. This bit is set when the MII auto-polling logic detects a change in link status and the LCMODE bit is set. LCDET is cleared when power is initially applied (POR). CSR114: Receive Collision Count Bit Reserved locations. Written as zeros and read as undefined. 10 PME_EN_OVR PME_EN Overwrite. When this bit is set and the MPMAT or LCDET bit is set, the PME pin will always be asserted regardless of the state of the PME_EN bit. CSR112: Missed Frame Count Bit Description Am79C978 LCMODE Link Change Wake-up Mode. When this bit is set to 1, the LCDET bit gets set when the MII auto polling logic detects a Link Change. Read/Write accessible only when either the STOP bit or the SPND bit is set. Cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 7 PMAT Pattern Matched. This bit is set when the PMMODE bit is set and an OnNow pattern match occurs. Read/Write accessible only when either the STOP bit or the SPND bit is set. Cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. PMAT is cleared when power is initially applied (POR). 3-1 This bit is read accessible always. 6 EMPPLBA Magic Packet Physical Logical Broadcast Accept. If both EMPPLBA and MPPLBA (CSR5, bit 5) are at their default value of 0, the Am79C978 controller will only detect a Magic Packet frame if the destination address of the packet matches the content of the physical address register (PADR). If either EMPPLBA or MPPLBA is set to 1, the destination address of the Magic Packet frame can be unicast, multicast, or broadcast. Note that the setting of EMPPLBA and MPPLBA only affects the address detection of the Magic Packet frame. The Magic Packet frame's data sequence must be made up of 16 consecutive physical addresses (PADR[47:0]) regardless of what kind of destination address it has. 0 RST_POL MPMAT Bit Description RES Reserved locations. Written as zeros and read as undefined. 0 RCVALGN Receive Packet Align. When set, this bit forces the data field of ISO 8802-3 (IEEE/ANSI 802.3) packets to align to 0 MOD 4 address boundaries (i.e., DWord aligned addresses). It is important to note that this feature will only function correctly if all receive buffer boundaries are DWord aligned and all receive buffers have 0 MOD 4 lengths. In order to accomplish the data alignment, the Am79C978 controller simply inserts two bytes of random data at the beginning of the receive packet (i.e., before the ISO 8802-3 (IEEE/ANSI 802.3) destination address field). The MCNT field reported to the receive descriptor will not include the extra two bytes. Magic Packet Match. This bit is set when the integrated Ethernet controller detects a Magic Packet while it is in Magic Packet mode. Magic Packet Pin Enable. When this bit is set, the device enters the Magic Packet mode when the PG input goes LOW or MPEN bit (CSR5, bit 2) gets set to 1. This bit is OR'ed with MPEN bit (CSR5, bit 2). Name 31-1 This bit is always read/write accessible. MPPEN PHY_RST Pin Polarity. If the PHY_POL is set to 1, the PHY_RST pin is active LOW; otherwise PHY_RST is active HIGH. CSR122: Advanced Feature Control MPMAT is cleared when power is initially applied (POR). 4 Reserved locations. This bit is read/write accessible only when either the STOP bit or the SPND bit is set. Cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. This bit is always read/write accessible. EMPPLBA is set to 0 by H_RESET or S_RESET and is not affected by setting the STOP bit. 5 RES This bit is always read/write accessible. RCVALGN is cleared by H_RESET or S_RESET and is not affected by STOP. CSR124: Test Register 1 This register is used to place the Am79C978 controller into various test modes. The Runt Packet Accept is the only user accessible test mode. All other test modes are for AMD internal use only. Am79C978 143 Bit Name Description 31-4 RES Reserved locations. Written as zeros and read as undefined. 3 RPA Runt Packet Accept. This bit forces the Am79C978 controller to accept runt packets (packets shorter than 64 bytes). match due to delays in the part used to make up the final IPG. Changes should be added or subtracted from the provided hex value on a one-for-one basis. CAUTION: Use this parameter with care. By lowering the IPG below the ISO/IEC 8802-3 standard 96 bit times, the Am79C978 controller can interrupt normal network behavior. This bit is read accessible always; write accessible only when STOP is set to 1. RPA is cleared by H_RESET or S_RESET and is not affected by STOP. 2-0 RES These bits are read accessible always. Write accessible when the STOP bit is set to 1. IPG is set to 60h (96 Bit times) by H_RESET or S_RESET and is not affected by STOP. Reserved locations. Written as zeros and read as undefined. CSR125: MAC Enhanced Configuration Control Bit Name 7-0 Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-8 Inter Packet Gap. Changing IPG allows the user to program the Am79C978 controller for aggressiveness on a network. By changing the default value of 96 bit times (60h) the user can adjust the fairness or aggressiveness of the Am79C978 integrated MAC on the network. By programming a lower number of bit times other then the ISO/IEC 8802-3 standard requires, the Am79C978 controller will become more aggressive on the network. This aggressive nature will give rise to the Am79C978 controller possibly "capturing the network" at times by forcing other less aggressive nodes to defer. By programming a larger number of bit times, the Am79C978 home networking MAC will become less aggressive on the network and may defer more often than normal. The performance of the Am79C978 controller may decrease as the IPG value is increased from the default value. IPG Note: Programming of the IPG should be done in nibble intervals instead of absolute bit times. The decimal and hex values do not 144 Am79C978 IFS1 InterFrameSpacingPart1. Changing IFS1 allows the user to program the value of the InterFrameSpacePart1 timing. The Am79C978 controller sets the default value at 60 bit times (3ch). See the subsection on Medium Allocation in the section Media Access Management for more details. The equation for setting IFS1 when IPG 96 bit times is: IFS1 = IPG - 36 bit times Note: Programming of the IPG should be done in nibble intervals instead of absolute bit times due to the MII. The decimal and hex values do not match due to delays in the part used to make up the final IPG. Changes should be added or subtracted from the provided hex value on a one-for-one basis. Due to changes in synchronization delays internally through different network ports, the IFS1 can be off by as much as +12 bit times. These bits are read accessible always. Write accessible only when the SPND bit or the STOP bit is set to 1. IFS1 is set to 3ch (60 bit times) by H_RESET or S_RESET and is not affected by STOP. Bus Configuration Registers (BCRs) The BCRs are used to program the configuration of the bus interface and other special features of the Am79C978 controller that are not related to the IEEE 802.3 MAC functions. The BCRs are accessed by first setting the appropriate RAP value and then by performing a slave access to the BDP. See Table 35. All BCR registers are 16 bits in width in Word I/O mode (DWIO = 0, BCR18, bit 7) and 32 bits in width in DWord I/O mode (DWIO = 1). The upper 16 bits of all BCR registers is undefined when in DWord I/O mode. These bits should be written as zeros and should be treated as undefined when read. The default value given for any BCR is the value in the register after H_RESET. Some of these values may be changed shortly after H_RESET when the contents of the external EEPROM is automatically read in. None of the BCR register values are affected by the assertion of the STOP bit or S_RESET. Note that several registers have no default value. BCR0, BCR1, BCR3, BCR8, BCR10-17, and BCR21 are reserved and have undefined values. BCR2 and BCR34 are not observable without first being programmed through the EEPROM read operation or a user register write operation. BCR0, BCR1, BCR16, BCR17, and BCR21 are registers that are used by other devices in the PCnet family. Writing to these registers have no effect on the operation of the Am79C978 controller. 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 Reserved locations. After H_RESET, the value in this register will be 0005h. The setting of this register has no effect on any Am79C978 controller function. It is only included for software compatibility with other PCnet family devices. Read always. MSWRA is read only. Write operations have no effect. BCR2: Miscellaneous Configuration Note: Bits 15-0 in this register are programmable through the EEPROM. Bit 15-14 RES Reserved locations. Written and read as zeros. 13 Reserved locations. Written as zeros and read as undefined. 15-0 Reserved locations. After H_RESET, the value in this register will be 0005h. The setting of this register has no effect on any Am79C978 controller function. It is only included for software compatibility with other PCnet family devices. MSRDA This bit is always read/write accessible. TSTSHDEN is cleared to 0 by H_RESET and is unaffected by S_RESET or by setting the STOP bit. 12 Read always. MSRDA is read only. Write operations have no effect. BCR1: Master Mode Write Active Bit Name PHYSELEN This bit enables writes to BCR18[4:3] for software selection of various operation and test modes. When PHYSELEN is set to 0 (default), the two bits can only be written from the EEPROM. When PHYSELEN is set to 1, writes to BCR18[4:3] are enabled. Description 31-16 RES Description Reserved locations. Written as zeros and read as undefined. BCR0: Master Mode Read Active Name Name 31-16 RES Writes to those registers marked as "Reserved" will have no effect. Reads from these locations will produce undefined values. Bit MSWRA LEDPE LED Program Enable. When LEDPE is set to 1, programming of the LED0 (BCR4), LED1 (BCR5), LED2 (BCR6), LED3 (BCR7), and LED4 (BCR48) registers is enabled. When LEDPE is cleared to 0, programming of LED0 (BCR4), LED1 (BCR5), LED2 (BCR6), LED3 (BCR7), and LED4 (BCR48) registers is disabled. Writes to those registers will be ignored. Description Am79C978 145 Table 35. BCR Registers RAP 0 1 2 3 4 5 6 7 8 9 10-15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 Mnemonic MSRDA MSWRA MC Reserved LED0 LED1 LED2 LED3 Reserved FDC Reserved IOBASEL IOBASEU BSBC EECAS SWS INTCON PCILAT PCISID PCISVID SRAMSIZ SRAMB SRAMIC EBADDRL EBADDRU EBD STVAL MIICAS MIIADDR MIIMDR PCIVID Default 0005h 0005h 0002h N/A 00C0h 0084h 0088h 0090h N/A 0000h N/A N/A N/A 9001h 0002h 0000h N/A FF06h 0000h 0000h 0000h 0000h 0000h N/A N/A N/A FFFFh 0000h 0000h N/A 1022h 36 PMC_A C811h 37 38 39 40 41 42 43 44 45 46 47 48 49 DATA0 DATA1 DATA2 DATA3 DATA4 DATA5 DATA6 DATA7 PMR1 PMR2 PMR3 LED4 PHY Select 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h N/A N/A N/A 0082h 8101h 146 Name Reserved Reserved Miscellaneous Configuration Reserved LED0 Status LED1 Status LED2 Status LED3 Status Reserved Full-Duplex Control Reserved Reserved Reserved Burst and Bus Control EEPROM Control and Status Software Style Reserved PCI Latency PCI Subsystem ID PCI Subsystem Vendor ID SRAM Size SRAM Boundary SRAM Interface Control Expansion Bus Address Lower Expansion Bus Address Upper Expansion Bus Data Port Software Timer Value PHY Control and Status PHY Address PHY Management Data PCI Vendor ID PCI Power Management Capabilities (PMC) Alias Register PCI DATA Register 0 Alias Register PCI DATA Register 1 Alias Register PCI DATA Register 2 Alias Register PCI DATA Register 3 Alias Register PCI DATA Register 4 Alias Register PCI DATA Register 5 Alias Register PCI DATA Register 6 Alias Register PCI DATA Register 7 Alias Register Pattern Matching Register 1 Pattern Matching Register 2 Pattern Matching Register 3 LED4 Status PHY Select Am79C978 Programmability User EEPROM No No No No Yes Yes No No Yes Yes Yes Yes Yes Yes Yes Yes No No Yes Yes No No No No No No Yes Yes Yes No Yes No No No Yes Yes No Yes No Yes Yes Yes Yes Yes Yes Yes Yes No Yes No Yes No Yes No Yes Yes Yes Yes Yes No No Yes No Yes No No No No No No No No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No No Yes Yes This bit is always read/write accessible. LEDPE is cleared to 0 by H_RESET and is unaffected by S_RESET or by setting the STOP bit. 11-9 8 RES APROMWE Address PROM Write Enable. The Am79C978 controller contains a shadow RAM on board for storage of the first 16 bytes loaded from the serial EEPROM. Accesses to Address PROM I/O Resources will be directed toward this RAM. When APROMWE is set to 1, then write access to the shadow RAM will be enabled. INTLEVEL INTLEVEL should not be set to 1 when the Am79C978 controller is used in a PCI bus application. Reserved locations. Written and read as zeros. This bit is always read/write accessible. APROMWE is cleared to 0 by H_RESET and is unaffected by S_RESET or by setting the STOP bit. 7 terrupt channels to be shared by multiple devices. Interrupt Level. This bit allows the interrupt output signals to be programmed for level or edgesensitive applications. When INTLEVEL is cleared to 0, the INTA pin is configured for level-sensitive applications. In this mode, an interrupt request is signaled by a low level driven on the INTA pin by the Am79C978 controller. When the interrupt is cleared, the INTA pin is tri-stated by the Am79C978 controller and allowed to be pulled to a high level by an external pullup device. This mode is intended for systems which allow the interrupt signal to be shared by multiple devices. When INTLEVEL is set to 1, the INTA pin is configured for edgesensitive applications. In this mode, an interrupt request is signaled by a high level driven on the INTA pin by the Am79C978 controller. When the interrupt is cleared, the INTA pin is driven to a low level by the Am79C978 controller. This mode is intended for systems that do not allow in- This bit is always read/write accessible. INTLEVEL is cleared to 0 by H_RESET and is unaffected by S_RESET or by setting the STOP bit. 6-3 RES Reserved locations. Written as zeros and read as undefined. 2-0 RES Reserved locations. Written and read as zeros. BCR4: LED0 Status BCR4 controls the function(s) that the LED0 pin displays. Multiple functions can be simultaneously enabled on this LED pin. The LED display will indicate the logical OR of the enabled functions. BCR4 defaults to Link Status (LNKST) with pulse stretcher enabled (PSE = 1) and is fully programmable. Note: When LEDPE (BCR2, bit 12) is set to 1, programming of the LED0 Status register is enabled. When LEDPE is cleared to 0, programming of the LED0 register is disabled. Writes to those registers will be ignored. Note: Bits 15-0 in this register are programmable through the EEPROM. Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15 This bit indicates the current (non-stretched) value of the LED output pin. A value of 1 in this bit indicates that the OR of the enabled signals is true. LEDOUT The logical value of the LEDOUT status signal is determined by the settings of the individual Status Enable bits of the LED register (bits 8 and 6-0). This bit is read accessible always. This bit is read only; writes have no effect. LEDOUT is unaffected by H_RESET, S_RESET, or STOP. 14 Am79C978 LEDPOL LED Polarity. When this bit has the value 0, then the LED pin will 147 be driven to a LOW level whenever the OR of the enabled signals is true, and the LED pin will be disabled and allowed to float high whenever the OR of the enabled signals is false (i.e., the LED output will be an Open Drain output and the output value will be the inverse of the LEDOUT status bit). When this bit has the value 1, then the LED pin will be driven to a HIGH level whenever the OR of the enabled signals is true, and the LED pin will be driven to a LOW level whenever the OR of the enabled signals is false (i.e., the LED output will be a Totem Pole output and the output value will be the same polarity as the LEDOUT status bit.). 11-10 RES Reserved locations. Written and read as zeros. 9 Magic Packet Status Enable. When this bit is set to 1, a value of 1 is passed to the LEDOUT bit in this register when Magic Packet frame mode is enabled and a Magic Packet frame is detected on the network. MPSE This bit is always read/write accessible. MPSE is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 8 FDLSE The setting of this bit will not effect the polarity of the LEDOUT bit for this register. This bit is always read/write accessible. LEDPOL is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 13 LEDDIS LED Disable. This bit is used to disable the LED output. When LEDDIS has the value 1, then the LED output will always be disabled. When LEDDIS has the value 0, then the LED output value will be governed by the LEDOUT and LEDPOL values. This bit is always read/write accessible. FDLSE is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 7 PSE This bit is always read/write accessible. LEDDIS is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 12 100E 100 Mbps Enable. When this bit is set to 1, a value of 1 is passed to the LEDOUT bit in this register when the Am79C978 controller is operating at 100 Mbps mode. Pulse Stretcher Enable. When this bit is set, the LED illumination time is extended for each new occurrence of the enabled function for this LED output. A value of 0 disables the pulse stretcher. This bit is always read/write accessible. PSE is set to 1 by H_RESET and is not affected by S_RESET or setting the STOP bit. 6 This bit is always read/write accessible. 100E is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 148 Full-Duplex Link Status Enable. Indicates the Full-Duplex Link Test Status. When this bit is set, a value of 1 is passed to the LEDOUT signal when the Am79C978 controller is functioning in a Link Pass state and full-duplex operation is enabled. When the Am79C978 controller is not functioning in a Link Pass state with full-duplex operation being enabled, a value of 0 is passed to the LEDOUT signal. Am79C978 LNKSE Link Status Enable. When this bit is set, a value of 1 will be passed to the LEDOUT bit in this register when in Link Pass state. This bit is always read/write accessible. LNKSE is set to 1 by H_RESET and is not affected by S_RESET or setting the STOP bit. 5 RCVME Receive Match Status Enable. When this bit is set, a value of 1 is passed to the LEDOUT bit in this register when there is receive activity on the network that has passed the address match function for this node. All address matching modes are included: physical, logical filtering, broadcast, and promiscuous. This bit is always read/write accessible. RCVME is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 4 XMTE Transmit Status Enable. When this bit is set, a value of 1 is passed to the LEDOUT bit in this register when there is transmit activity on the network. This bit is always read/write accessible. XMTE is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 3 2 POWER RCVE This bit is always read/write accessible. COLE is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. BCR5: LED1 Status BCR5 controls the function(s) that the LED1 pin displays. Multiple functions can be simultaneously enabled on this LED pin. The LED display will indicate the logical OR of the enabled functions. BCR5 defaults to Receive Status (RCV) with pulse stretcher enabled (PSE = 1) and is fully programmable. Note: When LEDPE (BCR2, bit 12) is set to 1, programming of the LED1 Status register is enabled. When LEDPE is cleared to 0, programming of the LED1 register is disabled. Writes to those registers will be ignored. Note: Bits 15-0 in this register are programmable through the EEPROM. Bit Name 31-16 RES Reserved locations. Written as zeros and read as undefined. 15 This bit indicates the current (non-stretched) value of the LED output pin. A value of 1 in this bit indicates that the OR of the enabled signals is true. LEDOUT Power. When this bit is set to 1, the device is operating in HIGH power mode. The logical value of the LEDOUT status signal is determined by the settings of the individual Status Enable bits of the LED register (bits 8 and 6-0). Receive Status Enable. When this bit is set, a value of 1 is passed to the LEDOUT bit in this register when there is receive activity on the network. This bit is always read/write accessible. RCVE is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 1 SPEED Speed. When this bit is set to 1, the device is operating in HIGH speed mode. 0 COLE Collision Status Enable. When this bit is set, a value of 1 is passed to the LEDOUT bit in this register when there is collision activity on the network. Description This bit is always read accessible. This bit is read only; writes have no effect. LEDOUT is unaffected by H_RESET, S_RESET, or STOP. 14 Am79C978 LEDPOL LED Polarity. When this bit has the value 0, then the LED pin will be driven to a LOW level whenever the OR of the enabled signals is true, and the LED pin will be disabled and allowed to float high whenever the OR of the enabled signals is false (i.e., the LED output will be an Open Drain output and the output value will be the inverse of the LEDOUT status bit). 149 When this bit has the value 1, then the LED pin will be driven to a HIGH level whenever the OR of the enabled signals is true, and the LED pin will be driven to a LOW level whenever the OR of the enabled signals is false (i.e., the LED output will be a Totem Pole output and the output value will be the same polarity as the LEDOUT status bit). This bit is always read/write accessible. MPSE is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 8 FDLSE The setting of this bit will not effect the polarity of the LEDOUT bit for this register. This bit is always read/write accessible. LEDPOL is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 13 LEDDIS LED Disable. This bit is used to disable the LED output. When LEDDIS has the value 1, then the LED output will always be disabled. When LEDDIS has the value 0, then the LED output value will be governed by the LEDOUT and LEDPOL values. This bit is always read/write accessible. FDLSE is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 7 PSE This bit is always read/write accessible. LEDDIS is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 12 100E 100 Mbps Enable. When this bit is set to 1, a value of 1 is passed to the LEDOUT bit in this register when the Am79C978 controller is operating at 100 Mbps mode. 9 150 MPSE Reserved locations. Written and read as zeros. Pulse Stretcher Enable. When this bit is set, the LED illumination time is extended for each new occurrence of the enabled function for this LED output. A value of 0 disables the pulse stretcher. This bit is always read/write accessible. PSE is set to 1 by H_RESET and is not affected by S_RESET or setting the STOP bit. 6 LNKSE This bit is always read/write accessible. 100E is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 11-10 RES Full-Duplex Link Status Enable. Indicates the Full-Duplex Link Test Status. When this bit is set, a value of 1 is passed to the LEDOUT signal when the Am79C978 controller is functioning in a Link Pass state and full-duplex operation is enabled. When the Am79C978 controller is not functioning in a Link Pass state with full-duplex operation being enabled, a value of 0 is passed to the LEDOUT signal. Link Status Enable. When this bit is set, a value of 1 will be passed to the LEDOUT bit in this register in Link Pass state. This bit is always read/write accessible. LNKSE is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 5 Magic Packet Status Enable. When this bit is set to 1, a value of 1 is passed to the LEDOUT bit in this register when Magic Packet mode is enabled and a Magic Packet frame is detected on the network. Am79C978 RCVME Receive Match Status Enable. When this bit is set, a value of 1 is passed to the LEDOUT bit in this register when there is receive activity on the network that has passed the address match function for this node. All address matching modes are included: physical, logical filtering, broadcast, and promiscuous. This bit is always read/write accessible. RCVME is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. Note: When LEDPE (BCR2, bit 12) is set to 1, programming of the LED2 Status register is enabled. When LEDPE is cleared to 0, programming of the LED2 register is disabled. Writes to those registers will be ignored. Note: Bits 15-0 in this register are programmable through the EEPROM PREAD operation. Bit 4 XMTE Transmit Status Enable. When this bit is set, a value of 1 is passed to the LEDOUT bit in this register when there is transmit activity on the network. Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15 This bit indicates the current (non-stretched) value of the LED output pin. A value of 1 in this bit indicates that the OR of the enabled signals is true. LEDOUT This bit is always read/write accessible. XMTE is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 3 POWER Power. When this bit is set to 1, the device is operating in HIGH power mode. The logical value of the LEDOUT status signal is determined by the settings of the individual Status Enable bits of the LED register (bits 8 and 6-0). 2 RCVE Receive Status Enable. When this bit is set, a value of 1 is passed to the LEDOUT bit in this register when there is receive activity on the network. This bit is read accessible always. This bit is read only; writes have no effect. LEDOUT is unaffected by H_RESET, S_RESET, or STOP. This bit is always read/write accessible. RCVE is set to 1 by H_RESET and is not affected by S_RESET or setting the STOP bit. 1 SPEED Speed. When this bit is set to 1, the device is operating in HIGH speed mode. 0 COLE Collision Status Enable. When this bit is set, a value of 1 is passed to the LEDOUT bit in this register when there is collision activity on the network. 14 This bit is always read/write accessible. COLE is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. BCR6: LED2 Status BCR6 controls the function(s) that the LED2 pin displays. Multiple functions can be simultaneously enabled on this LED pin. The LED display will indicate the logical OR of the enabled functions. Am79C978 LEDPOL LED Polarity. When this bit has the value 0, then the LED pin will be driven to a LOW level whenever the OR of the enabled signals is true, and the LED pin will be disabled and allowed to float high whenever the OR of the enabled signals is false (i.e., the LED output will be an Open Drain output and the output value will be the inverse of the LEDOUT status bit). When this bit has the value 1, then the LED pin will be driven to a HIGH level whenever the OR of the enabled signals is true, and the LED pin will be driven to a LOW level whenever the OR of the enabled signals is false (i.e., the LED output will be a Totem Pole output and the output value will be the same polarity as the LEDOUT status bit). The setting of this bit will not effect the polarity of the LEDOUT bit for this register. 151 13 LEDDIS This bit is always read/write accessible. LEDPOL is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. Am79C978 controller is not functioning in a Link Pass state with full-duplex operation being enabled, a value of 0 is passed to the LEDOUT signal. LED Disable. This bit is used to disable the LED output. When LEDDIS has the value 1, then the LED output will always be disabled. When LEDDIS has the value 0, then the LED output value will be governed by the LEDOUT and LEDPOL values. This bit is always read/write accessible. FDLSE is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 7 PSE This bit is always read/write accessible. LEDDIS is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 12 100E 100 Mbps Enable. When this bit is set to 1, a value of 1 is passed to the LEDOUT bit in this register when the Am79C978 controller is operating at 100 Mbps mode. This bit is always read/write accessible. PSE is set to 1 by H_RESET and is not affected by S_RESET or setting the STOP bit. 6 LNKSE This bit is always read/write accessible. 100E is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 11-10 RES Reserved locations. Written and read as zeros. 9 Magic Packet Status Enable. When this bit is set to 1, a value of 1 is passed to the LEDOUT bit in this register when Magic Packet frame mode is enabled and a Magic Packet frame is detected on the network. MPSE 152 FDLSE Full-Duplex Link Status Enable. Indicates the Full-Duplex Link Test Status. When this bit is set, a value of 1 is passed to the LEDOUT signal when the Am79C978 controller is functioning in a Link Pass state and full-duplex operation is enabled. When the Link Status Enable. When this bit is set, a value of 1 will be passed to the LEDOUT bit in this register in Link Pass state. This bit is always read/write accessible. LNKSE is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 5 RCVME This bit is always read/write accessible. MPSE is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 8 Pulse Stretcher Enable. When this bit is set, the LED illumination time is extended for each new occurrence of the enabled function for this LED output. A value of 0 disables the pulse stretcher. Receive Match Status Enable. When this bit is set, a value of 1 is passed to the LEDOUT bit in this register when there is receive activity on the network that has passed the address match function for this node. All address matching modes are included: physical, logical filtering, broadcast, and promiscuous. This bit is always read/write accessible. RCVME is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 4 Am79C978 XMTE Transmit Status Enable. When this bit is set, a value of 1 is passed to the LEDOUT bit in this register when there is transmit activity on the network. This bit is always read/write accessible. XMTE is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 3 POWER Power. When this bit is set to 1, the device is operating in HIGH power mode. 2 RCVE Receive Status Enable. When this bit is set, a value of 1 is passed to the LEDOUT bit in this register when there is receive activity on the network. This bit is always read/write accessible. RCVE is set to 1 by H_RESET and is not affected by S_RESET or setting the STOP bit. 1 SPEED Speed. When this bit is set to 1, the device is operating in HIGH speed mode. 0 COLE Collision Status Enable. When this bit is set, a value of 1 is passed to the LEDOUT bit in this register when there is collision activity on the network. 15 LEDOUT The logical value of the LEDOUT status signal is determined by the settings of the individual Status Enable bits of the LED register (bits 8 and 6-0). This bit is read accessible always. This bit is read only; writes have no effect. LEDOUT is unaffected by H_RESET, S_RESET, or STOP. 14 LEDPOL BCR7: LED3 Status BCR7 controls the function(s) that the LED3 pin displays. Multiple functions can be simultaneously enabled on this LED pin. The LED display will indicate the logical OR of the enabled functions. BCR7 defaults to Transmit Status (XMT) with pulse stretcher enabled (PSE = 1) and is fully programmable. The setting of this bit will not effect the polarity of the LEDOUT bit for this register. Note: When LEDPE (BCR2, bit 12) is set to 1, programming of the LED3 Status register is enabled. When LEDPE is cleared to 0, programming of the LED3 register is disabled. Writes to those registers will be ignored. Bit Name 31-16 RES Description LED Polarity. When this bit has the value 0, then the LED pin will be driven to a LOW level whenever the OR of the enabled signals is true, and the LED pin will be disabled and allowed to float high whenever the OR of the enabled signals is false (i.e., the LED output will be an Open Drain output and the output value will be the inverse of the LEDOUT status bit.). When this bit has the value 1, then the LED pin will be driven to a HIGH level whenever the OR of the enabled signals is true, and the LED pin will be driven to a LOW level whenever the OR of the enabled signals is false (i.e., the LED output will be a Totem Pole output and the output value will be the same polarity as the LEDOUT status bit). This bit is always read/write accessible. COLE is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. Note: Bits 15-0 in this register are programmable through the EEPROM. This bit indicates the current (non-stretched) value of the LED output pin. A value of 1 in this bit indicates that the OR of the enabled signals is true. This bit is always read/write accessible. LEDPOL is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 13 Reserved locations. Written as zeros and read as undefined. Am79C978 LEDDIS LED Disable. This bit is used to disable the LED output. When LEDDIS has the value 1, then the LED output will always be disabled. When LEDDIS has the value 0, then the LED output value 153 will be governed by the LEDOUT and LEDPOL values. time is extended for each new occurrence of the enabled function for this LED output. A value of 0 disables the pulse stretcher. This bit is always read/write accessible. LEDDIS is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 12 100E 100 Mbps Enable. When this bit is set to 1, a value of 1 is passed to the LEDOUT bit in this register when the Am79C978 controller is operating at 100 Mbps mode. This bit is always read/write accessible. PSE is set to 1 by H_RESET and is not affected by S_RESET or setting the STOP bit. 6 LNKSE This bit is always read/write accessible. 100E is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 11-10 RES 9 MPSE Reserved locations. Written and read as zeros. This bit is always read/write accessible. LNKSE is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 5 RCVME Magic Packet Status Enable. When this bit is set to 1, a value of 1 is passed to the LEDOUT bit in this register when magic frame mode is enabled and a magic frame is detected on the network. This bit is always read/write accessible. MPSE is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 8 FDLSE Full-Duplex Link Status Enable. Indicates the Full-Duplex Link Test Status. When this bit is set, a value of 1 is passed to the LEDOUT signal when the Am79C978 controller is functioning in a Link Pass state and full-duplex operation is enabled. When the Am79C978 controller is not functioning in a Link Pass state with full-duplex operation being enabled, a value of 0 is passed to the LEDOUT signal. This bit is always read/write accessible. FDLSE is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 7 154 PSE Link Status Enable. When this bit is set, a value of 1 will be passed to the LEDOUT bit in this register in Link Pass state. Receive Match Status Enable. When this bit is set, a value of 1 is passed to the LEDOUT bit in this register when there is receive activity on the network that has passed the address match function for this node. All address matching modes are included: physical, logical filtering, broadcast, and promiscuous. This bit is always read/write accessible. RCVME is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 4 XMTE Transmit Status Enable. When this bit is set, a value of 1 is passed to the LEDOUT bit in this register when there is transmit activity on the network. This bit is always read/write accessible. XMTE is set to 1 by H_RESET and is not affected by S_RESET or setting the STOP bit. 3 POWER Power. When this bit is set to 1, the device is operating in HIGH power mode. 2 RCVE Receive Status Enable. When this bit is set, a value of 1 is passed to the LEDOUT bit in this Pulse Stretcher Enable. When this bit is set, the LED illumination Am79C978 register when there is receive activity on the network. This bit is always read/write accessible. RCVE is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 1 SPEED Speed. When this bit is set to 1, the device is operating in HIGH speed mode. 0 COLE Collision Status Enable. When this bit is set, a value of 1 is passed to the LEDOUT bit in this register when there is collision activity on the network. S_RESET or by setting the STOP bit. 1 RES Reserved locations. Written as zeros and read as undefined. 0 FDEN Full-Duplex Enable. FDEN controls whether full-duplex operation is enabled. When FDEN is cleared and the Auto-Negotiation is disabled, full-duplex operation is not enabled and the Am79C978 controller will always operate in half-duplex mode. When FDEN is set, the Am79C978 controller will operate in full-duplex mode. Do not set this bit when Auto-Negotiation is enabled. This bit is always read/write accessible. COLE is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. This bit is always read/write accessible. FDEN is reset to 0 by H_RESET, and is unaffected by S_RESET and the STOP bit. BCR9: Full-Duplex Control BCR16: I/O Base Address Lower Note: Bits 15-0 in this register are programmable through the EEPROM. Bit Bit Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-5 Reserved locations. After H_RESET, the value of these bits will be undefined. The settings of these bits will have no effect on any Am79C978 controller function. Name 31-3 RES Reserved locations. Written as zeros and read as undefined. 2 FDRPAD Full-Duplex Runt Packet Accept Disable. When FDRPAD is set to 1 and full-duplex mode is enabled, the Am79C978 controller will only receive frames that meet the minimum Ethernet frame length of 64 bytes. Receive DMA will not start until at least 64 bytes or a complete frame have been received. By default, FDRPAD is cleared to 0. The Am79C978 controller will accept any length frame and receive DMA will start according to the programming of the receive FIFO watermark. Note that there should not be any runt packets in a full-duplex network, since the main cause for runt packets is a network collision and there are no collisions in a full-duplex network. Name IOBASEL Description These bits are always read/write accessible. IOBASEL is not affected by S_RESET or STOP. 4-0 RES Reserved locations. Written as zeros, read as undefined. BCR17: I/O Base Address Upper Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 Reserved locations. After H_RESET, the value in this register will be undefined. The settings of this register will have no effect on any Am79C978 controller function. This bit is always read/write accessible. FDRPAD is cleared by H_RESET and is not affected by Am79C978 IOBASEU 155 This bit is always read/write accessible. IOBASEU is not affected by S_RESET or STOP. tACC = ROMTMG * CLK period *CLK_FAC - (tv_A_D) + (ts_D) The access time for the Expansion ROM or for the EBDATA (BCR30) device (tACC) during write operations can be calculated by subtracting the clock to output delay for the EBUA EBA[7:0] outputs (tv_A_D) and by adding the input to clock setup time for Flash/EPRO inputs (ts_D) from the time defined by ROMTMG. BCR18: Burst and Bus Control Register Note: Bits 15-0 in this register are programmable through the EEPROM. Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-12 ROMTMG Expansion ROM Timing. The value of ROMTMG is used to tune the timing for all EBDATA (BCR30) accesses to Flash/ EPROM as well as all Expansion ROM accesses to Flash/EPROM. tACC = ROMTMG * CLK period * CLK_FAC - (tv_A_D) - (ts_D) For an adapter card application, the value used for clock period should be 30 ns to guarantee correct interface timing at the maximum clock frequency of 33 MHz. ROMTMG, during read operations, defines the time from when the Am79C978 controller drives the lower 8 or 16 bits of the Expansion Bus Address bus to when the Am79C978 controller latches in the data on the 8 or 16 bits of the Expansion Bus Data inputs. ROMTMG, during write operations, defines the time from when the Am79C978 controller drives the lower 8 or 16 bits of the Expansion Bus Data to when the EBWE and EROMCS deassert. These bits are read accessible always; write accessible only when the STOP bit is set. ROMTMG is set to the value of 1001b by H_RESET and is not affected by S_RESET or STOP. The default value allows using an Expansion ROM with an access time of 250 ns in a system with a maximum clock frequency of 33 MHz. 11 The register value specifies the time in number of clock cycles +1 according to Table 36. Table 36. ROMTNG Programming Values ROMTMG (bits 15-12) No. of Expansion Bus Cycles 1h<=n <=Fh n+1 Note: Programming ROMTNG with a value of 0 is not permitted. The access time for the Expansion ROM or the EBDATA (BCR30) device (tACC) during read operations can be calculated by subtracting the clock to output delay for the EBUA_EBA[7:0] outputs (tv_A_D) and by subtracting the input to clock setup time for the EBD[7:0] inputs (ts_D) from the time defined by ROMTMG: 156 Am79C978 NOUFLO No Underflow on Transmit. When the NOUFLO bit is set to 1, the Am79C978 controller will not start transmitting the preamble for a packet until the Transmit Start Point (CSR80, bits 10-11) requirement (except when XMTSP = 3h, Full Packet has no meaning when NOUFLO is set to 1) has been met and the complete packet has been DMA'd into the Am79C978 controller. The complete packet may reside in any combination of the Bus Transmit FIFO, the SRAM, and the MAC Transmit FIFO as long as enough of the packet is in the MAC Transmit FIFO to meet the Transmit Start Point requirement. When the NOUFLO bit is cleared to 0, the Transmit Start Point is the only restriction on when preamble transmission begins for transmit packets. Setting the NOUFLO bit guarantees that the Am79C978 controller will never suffer transmit underflows, because the arbiter that controls transfers to and from the SRAM guarantees a worst case latency on transfers to and from the MAC and Bus Transmit FIFOs such that it will never underflow if the complete packet has been DMA'd into the Am79C978 controller before packet transmission begins. the system arbiter also removes GNT at the beginning of the burst transaction. If EXTREQ is set to 1, REQ stays asserted until the last but one data phase of the burst transaction is done. This mode is useful for systems that implement an arbitration scheme without preemption and require that REQ stays asserted throughout the transaction. EXTREQ should not be set to 1 when the Am79C978 controller is used in a PCI bus application. The NOUFLO bit has no effect when the Am79C978 controller is operating in the NO-SRAM mode. This bit is read accessible always, write accessible only when either the STOP or the SPND bit is set. EXTREQ is cleared by H_RESET and is not affected by S_RESET or STOP. Read/Write accessible only when either the STOP or the SPND bit is set. NOUFLO is cleared to 0 after H_RESET or S_RESET and is unaffected by STOP. 7 10 RES Reserved location. Written as zero and read as undefined. 9 MEMCMD Memory Command used for burst read accesses to the transmit buffer. When MEMCMD is set to 0, all burst read accesses to the transmit buffer are of the PCI command type Memory Read Line (type 14). When MEMCMD is set to 1, all burst read accesses to the transmit buffer are of the PCI command type Memory Read Multiple (type 12). This bit is read accessible always; write accessible only when either the STOP or the SPND bit is set. MEMCMD is cleared by H_RESET and is not affected by S_RESET or STOP. 8 EXTREQ Extended Request. This bit controls the deassertion of REQ for a burst transaction. If EXTREQ is set to 0, REQ is deasserted at the beginning of a burst transaction. (The Am79C978 controller never performs more than one burst transaction within a single bus mastership period.) In this mode, the Am79C978 controller relies on the PCI latency timer to get enough bus bandwidth, in case Am79C978 DWIO Double Word I/O. When set, this bit indicates that the Am79C978 controller is programmed for DWord I/O (DWIO) mode. When cleared, this bit indicates that the Am79C978 controller is programmed for Word I/O (WIO) mode. This bit affects the I/O Resource Offset map and it affects the defined width of the Am79C978 controller's I/O resources. See the DWIO and WIO sections for more details. The initial value of the DWIO bit is determined by the programming of the EEPROM. The value of DWIO can be altered automatically by the Am79C978 controller. Specifically, the Am79C978 controller will set DWIO if it detects a DWord write access to offset 10h from the Am79C978 controller's I/O base address (corresponding to the RDP resource). Once the DWIO bit has been set to a 1, only a H_RESET or an EEPROM read can reset it to a 0. (Note that the EEPROM read operation will only set DWIO to a 0 if the appropriate bit inside of the EEPROM is set to 0.) 157 This bit is read accessible always. DWIO is read only, write operations have no effect. DWIO is cleared by H_RESET and is not affected S_RESET or by setting the STOP bit. 6 BREADE The normal mode of operation is when both bits 0 and 1 are set to 0 to select the Expansion ROM/ Flash. Setting bit 0 to 1 and bit 1 to 0 allows snooping of the internal MII-compatible bus to allow External Address Detection Interface (EADI). See Table 37 for details. Burst Read Enable. When set, this bit enables burst mode during memory read accesses. When cleared, this bit prevents the device from performing bursting during read accesses. The Am79C978 controller can perform burst transfers when reading the initialization block, the descriptor ring entries (when SWSTYLE = 3), and the buffer memory. Table 37. PHYSEL [1:0] 5 BWRITE Burst Write Enable. When set, this bit enables burst mode during memory write accesses. When cleared, this bit prevents the device from performing bursting during write accesses. The Am79C978 controller can perform burst transfers when writing the descriptor ring entries (when SWSTYLE = 3), and the buffer memory. BWRITE should be set to 1 when the Am79C978 controller is used in a PCI bus application to guarantee maximum performance. Expansion ROM/Flash 01 EADI/Internal MII Snoop 10 Reserved 11 Reserved These bits are read accessible always, these bits can only be written from the EEPROM unless a write-enable bit, BCR2[13], is set. PHYSEL [1:0] is cleared by H_RESET and is not affected by S_RESET or STOP. 2-0 158 LINBC Reserved locations. These bits are read accessible always; write accessible only when either the STOP or the SPND bit is set. After H_RESET, the value in these bits will be 001b. The setting of these bits have no effect on any Am79C978 controller's function. LINBC is not affected by S_RESET or STOP. BCR19: EEPROM Control and Status Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15 EEPROM Valid status bit. This bit is read accessible only. PVALID is read only; write operations have no effect. A value of 1 in this bit indicates that a PREAD operation has occurred, and that (1) there is an EEPROM connected to the Am79C978 controller interface pins and (2) the contents read from the EEPROM have passed the checksum verification operation. This bit is read accessible always, write accessible only when either the STOP or the SPND bit is set. BWRITE is cleared by H_RESET and is not affected by S_RESET or STOP. 4-3 Mode 00 BREADE should be set to 1 when the Am79C978 controller is used in a PCI bus application to guarantee maximum performance. This bit is read accessible always; write accessible only when either the STOP or the SPND bit is set. BREADE is cleared by H_RESET and is not affected by S_RESET or STOP. PHY Select Programming PHYSEL[1:0] PHYSEL[1:0] bits allow for software controlled selection of different operation and test modes. Am79C978 PVALID A value of 0 in this bit indicates a failure in reading the EEPROM. The checksum for the entire 82 bytes of EEPROM is incorrect or no EEPROM is connected to the interface pins. PVALID is set to 0 during H_RESET and is unaffected by S_RESET or the STOP bit. However, following the H_RESET operation, an automatic read of the EEPROM will be performed. Just as it is true for the normal PREAD command, at the end of this automatic read operation the PVALID bit may be set to 1. Therefore, H_RESET will set the PVALID bit to 0 at first, but the automatic EEPROM read operation may later set PVALID to a 1. If PVALID becomes 0 following an EEPROM read operation (either automatically generated after H_RESET, or requested through PREAD), then all EEPROM-programmable BCR locations will be reset to their H_RESET values. The content of the Address PROM locations, however, will not be cleared. If no EEPROM is present at the EESK, EEDI, and EEDO pins, then all attempted PREAD commands will terminate early and PVALID will not be set. This applies to the automatic read of the EEPROM after H_RESET, as well as to host-initiated PREAD commands. 14 PREAD EEPROM Read command bit. When this bit is set to a 1 by the host, the PVALID bit (BCR19, bit 15) will immediately be reset to a 0, and then the Am79C978 controller will perform a read operation of 82 bytes from the EEPROM through the interface. The EEPROM data that is fetched during the read will be stored in the appropriate internal registers on board the Am79C978 controller. Upon completion of the EEPROM read operation, the Am79C978 controller Am79C978 will assert the PVALID bit. EEPROM contents will be indirectly accessible to the host through read accesses to the Address PROM (offsets 0h through Fh) and through read accesses to other EEPROM programmable registers. Note that read accesses from these locations will not actually access the EEPROM itself, but instead will access the Am79C978 internal copy of the EEPROM contents. Write accesses to these locations may change the Am79C978 register contents, but the EEPROM locations will not be affected. EEPROM locations may be accessed directly through BCR19. At the end of the read operation, the PREAD bit will automatically be reset to a 0 by the Am79C978 controller and PVALID will be set, provided that an EEPROM existed on the interface pins and that the checksum for the entire 68 bytes of EEPROM was correct. Note that when PREAD is set to a 1, then the Am79C978 controller will no longer respond to any accesses directed toward it, until the PREAD operation has completed successfully. The Am79C978 controller will terminate these accesses with the assertion of DEVSEL and STOP while TRDY is not asserted, signaling to the initiator to disconnect and retry the access at a later time. If a PREAD command is given to the Am79C978 controller but no EEPROM is attached to the interface pins, the PREAD bit will be cleared to a 0, and the PVALID bit will remain reset with a value of 0. This applies to the automatic read of the EEPROM after H_RESET as well as to host initiated PREAD commands. EEPROM programmable locations on board the Am79C978 controller will be set to their default values by such an aborted PREAD 159 operation. For example, if the aborted PREAD operation immediately followed the H_RESET operation, then the final state of the EEPROM programmable locations will be equal to the H_RESET programming for those locations. 12-5 RES Reserved locations. Written as zeros; read as undefined. 4 EEN EEPROM Port Enable. When this bit is set to a 1, it causes the values of ECS, ESK, and EDI to be driven onto the EECS, EESK, and EEDI pins, respectively. If EEN = 0 and no EEPROM read function is currently active, then EECS will be driven LOW. When EEN = 0 and no EEPROM read function is currently active, EESK and EEDI pins will be driven by the LED registers BCR5 and BCR4, respectively. See Table 39. If a PREAD command is given to the Am79C978 controller and the auto-detection pin (EESK/LED1) indicates that no EEPROM is present, then the EEPROM read operation will still be attempted. Note that at the end of the H_RESET operation, a read of the EEPROM will be performed automatically. This H_RESETgenerated EEPROM read function will not proceed if the autodetection pin (EESK/LED1) indicates that no EEPROM is present. This bit is read accessible always; write accessible only when either the STOP or the SPND bit is set. PREAD is set to 0 during H_RESET and is unaffected by S_RESET or the STOP bit. 13 EEDET This bit is read accessible always, write accessible only when either the STOP or the SPND bit is set. EEN is set to 0 by H_RESET and is unaffected by the S_RESET or STOP bit. 3 RES Reserved location. Written as zero and read as undefined. 2 ECS EEPROM Chip Select. This bit is used to control the value of the EECS pin of the interface when the EEN bit is set to 1 and the PREAD bit is set to 0. If EEN = 1 and PREAD = 0 and ECS is set to a 1, then the EECS pin will be forced to a HIGH level at the rising edge of the next clock following bit programming. EEPROM Detect. This bit indicates the sampled value of the EESK/LED1 pin at the end of H_RESET. This value indicates whether or not an EEPROM is present at the EEPROM interface. If this bit is a 1, it indicates that an EEPROM is present. If this bit is a 0, it indicates that an EEPROM is not present. This bit is read accessible only. EEDET is read only; write operations have no effect. The value of this bit is determined at the end of the H_RESET operation. It is unaffected by S_RESET or the STOP bit. Table 38 indicates the possible combinations of EEDET and the existence of an EEPROM and the resulting operations that are possible on the EEPROM interface. 160 Am79C978 If EEN = 1 and PREAD = 0 and ECS is set to a 0, then the EECS pin will be forced to a LOW level at the rising edge of the next clock following bit programming. ECS has no effect on the output value of the EECS pin unless the PREAD bit is set to 0 and the EEN bit is set to 1. This bit is read accessible always, write accessible only when either the STOP or the SPND bit is set. ECS is set to 0 by H_RESET and is not affected by S_RESET or STOP. Table 38. EEDET Setting EEDET Value (BCR19[13]) EEPROM Connected? 0 No 0 Yes 1 No 1 Yes Result if PREAD is Set to 1 EEPROM read operation is attempted. Entire read sequence will occur, checksum failure will result, PVALID is reset to 0. EEPROM read operation is attempted. Entire read sequence will occur, checksum operation will pass, PVALID is set to 1. EEPROM read operation is attempted. Entire read sequence will occur, checksum failure will result, PVALID is reset to 0. EEPROM read operation is attempted. Entire read sequence will occur, checksum operation will pass, PVALID is set to 1. Table 39. RST Pin Low High PREAD or Auto Read in Progress X 1 EEN X X High 0 1 High 0 0 1 ESK Interface Pin Assignment EECS 0 Active From ECS Bit of BCR19 0 EEPROM Serial Clock. This bit and the EDI/EDO bit are used to control host access to the EEPROM. Values programmed to this bit are placed onto the EESK pin at the rising edge of the next clock following bit programming, except when the PREAD bit is set to 1 or the EEN bit is set to 0. If both the ESK bit and the EDI/ EDO bit values are changed during one BCR19 write operation, while EEN = 1, then setup and hold times of the EEDI pin value with respect to the EESK signal edge are not guaranteed. ESK has no effect on the EESK pin unless the PREAD bit is set to 0 and the EEN bit is set to 1. This bit is read accessible always, write accessible only when either the STOP or the SPND bit is set. ESK is reset to 1 by H_RESET and is not affected by S_RESET or STOP. 0 EDI/EDO Result of Automatic EEPROM Read Operation Following H_RESET First two EESK clock cycles are generated, then EEPROM read operation is aborted and PVALID is reset to 0. First two EESK clock cycles are generated, then EEPROM read operation is aborted and PVALID is reset to 0. EEPROM read operation is attempted. Entire read sequence will occur, checksum failure will result, PVALID is reset to 0. EEPROM read operation is attempted. Entire read sequence will occur, checksum operation will pass, PVALID is set to 1. EESK Tri-State Active EEDI Tri-State Active From ESK Bit of BCR19 From EEDI Bit of BCR19 LED1 LED0 this bit will appear on the EEDI output of the interface, except when the PREAD bit is set to 1 or the EEN bit is set to 0. Data that is read from this bit reflects the value of the EEDO input of the interface. EDI/EDO has no effect on the EEDI pin unless the PREAD bit is set to 0 and the EEN bit is set to 1. Read accessible always; write accessible only when either the STOP or the SPND bit is set. EDI/ EDO is reset to 0 by H_RESET and is not affected by S_RESET or STOP. BCR20: Software Style This register is an alias of the location CSR58. Accesses to and from this register are equivalent to accesses to CSR58. Bit Name 31-11 RES EEPROM Data In/EEPROM Data Out. Data that is written to Am79C978 Description Reserved locations. Written as zeros and read as undefined. 161 10 APERREN Advanced Parity Error Handling Enable. When APERREN is set to 1, the BPE bits (RMD1 and TMD1, bit 23) start having a meaning. BPE will be set in the descriptor associated with the buffer that was accessed when a data parity error occurred. Note that since the advanced parity error handling uses an additional bit in the descriptor, SWSTYLE (bits 7-0 of this register) must be set to 2 or 3 to program the Am79C978 controller to use 32-bit software structures. faults to 0) and is not affected by S_RESET or STOP. APERREN does not affect the reporting of address parity errors or data parity errors that occur when the Am79C978 controller is the target of the transfer. If SSIZE32 is set, then the software structures that are common to the Am79C978 controller and the host system will supply a full 32 bits for each address pointer that is needed by the Am79C978 controller for performing master accesses. If SSIZE32 is reset, then bits IADR[31:24] of CSR2 will be used to generate values for the upper 8 bits of the 32-bit address bus during master accesses initiated by the Am79C978 controller. This action is required, since the 16-bit software structures specified by the SSIZE32 = 0 setting will yield only 24 bits of address for Am79C978 controller bus master accesses. Read anytime; write accessible only when either the STOP or the SPND bit is set. APERREN is cleared by H_RESET and is not affected by S_RESET or STOP. 9 RES Reserved location. Written as zero; read as undefined. 8 SSIZE32 Software Size 32 bits. When set, this bit indicates that the Am79C978 controller utilizes 32bit software structures for the initialization block and the transmit and receive descriptor entries. When cleared, this bit indicates that the Am79C978 controller utilizes 16-bit software structures for the initialization block and the transmit and receive descriptor entries. In this mode, the Am79C978 controller is backwards compatible with the Am7990 LANCE and Am79C960 PCnet-ISA controllers. The value of the SSIZE32 bit has no effect on the drive of the upper 8 address bits. The upper 8 address pins are always driven, regardless of the state of the SSIZE32 bit. Note that the setting of the SSIZE32 bit has no effect on the defined width for I/O resources. I/O resource width is determined by the state of the DWIO bit (BCR18, bit 7). 7-0 The value of SSIZE32 is determined by the Am79C978 controller according to the setting of the Software Style (SWSTYLE, bits 7-0 of this register). This bit is always read accessible. SSIZE32 is read only; write operations will be ignored. SSIZE32 will be cleared after H_RESET (since SWSTYLE de- 162 Am79C978 SWSTYLE Software Style register. The value in this register determines the style of register and memory resources that shall be used by the Am79C978 controller. The Software Style selection will affect the interpretation of a few bits within the CSR space, the order of the descriptor entries and the width of the descriptors and initialization block entries. All Am79C978 CSR bits and all descriptor, buffer, and initialization block entries not cited in the Table 40 are unaffected by the Software Style selection and are, therefore, always fully functional as specified in the CSR and BCR sections. Read/Write accessible only when either the STOP or the SPND bit is set. The SWSTYLE register will contain the value 00h following H_RESET and will be unaffected by S_RESET or STOP. Table 40. Software Styles SWSTYLE [7:0] Style Name LANCE/ 00h PCnet-ISA controller RES 01h 02h 03h 1 1 PCnet-PCI 1 controller RES 16-bit software structures, non-burst or burst access 0 PCnet-PCI controller All Other Initialization Block Entries SSIZE32 Undefined RES 32-bit software structures, non-burst or burst access 32-bit software structures, non-burst or burst access Undefined BCR22: PCI Latency Register Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-8 Maximum Latency. Specifies the maximum arbitration latency the Am79C978 controller can sustain without causing problems to the network activity. The register value specifies the time in units of 1/ 4 microseconds. MAX_LAT is aliased to the PCI configuration space register MAX_LAT (offset 3Fh). The host will use the value in the register to determine the setting of the Am79C978 Latency Timer register. MAX_LAT Read accessible always; write accessible only when either the STOP or the SPND bit is set. MAX_LAT is set to the value of FFh by H_RESET which results in a default maximum latency of 63.75 microseconds. It is recommended to program the value of 18h via EEPROM. MAX_LAT is not affected by S_RESET or STOP. 7-0 MIN_GNT Minimum Grant. Specifies the minimum length of a burst period the Am79C978 controller needs to keep up with the network activ- 16-bit software structures, non-burst access only RES 32-bit software structures, non-burst access only 32-bit software structures, non-burst or burst access Undefined ity. The length of the burst period is calculated assuming a clock rate of 33 MHz. The register value specifies the time in units of 1/ 4 ms. MIN_GNT is aliased to the PCI Configuration Space register MIN_GNT (offset 3Eh). The host will use the value in the register to determine the setting of the Am79C978 Latency Timer register. Note: Bits 15-0 in this register are programmable through the EEPROM. Bit Descriptor Ring Entries Read accessible always; write accessible only when either the STOP or the SPND bit is set. MIN_GNT is set to the value of 06h by H_RESET which results in a default minimum grant of 1.5 ms, which is the time it takes to Am79C978 controller to read/ write half of the FIFO. (16 DWord transfers in burst mode with one extra wait state per data phase inserted by the target.) Note that the default is only a typical value. It also does not take into account any descriptor accesses. It is recommended to program the value of 18h via EEPROM. MIN_GNT is not affected by S_RESET or STOP. BCR23: PCI Subsystem Vendor ID Register Note: Bits 15-0 in this register are programmable through the EEPROM. Bit Am79C978 Name Description 163 31-0 RES Reserved locations. Written as zeros and read as undefined. 15-0 SVID Subsystem Vendor ID. SVID is used together with SID (BCR24, bits 15-0) to uniquely identify the add-in board or subsystem the Am79C978 controller is used in. Subsystem Vendor IDs can be obtained from the PCI SIG. A value of 0 (the default) indicates that the Am79C978 controller does not support subsystem identification. SVID is aliased to the PCI Configuration Space register Subsystem Vendor ID (offset 2Ch). Note: Bits 7-0 in this register are programmable through the EEPROM. 31-8 7-0 This bit is always read accessible. SVID is read only. Write operations are ignored. SVID is cleared to 0 by H_RESET and is not affected by S_RESET or by setting the STOP bit. RES SRAM_SIZE SRAM Size. Specifies the upper 8 bits of the 16-bit total size of the SRAM buffer. Each bit in SRAM_SIZE accounts for a 512byte page. The starting address for the lower 8 bits is assumed to be 00h and the ending address for the lower is assumed to be FFh. Therefore, the maximum address range is the starting address of 0000h to ending address of ((SRAM_SIZE+1) * 256 words) or 17FFh. An SRAM_SIZE value of all zeros specifies that no SRAM will be used and the internal FIFOs will be joined into a contiguous FIFO similar to the PCnet-PCI II controller. Note: The minimum allowed number of pages is eight for normal network operation. The Am79C978 controller will not operate correctly with less than the eight pages of memory. When the minimum number of pages is used, these pages must be allocated four each for transmit and receive. BCR24: PCI Subsystem ID Register Note: Bits 15-0 in this register are programmable through the EEPROM. Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 Subsystem ID. SID is used together with SVID (BCR23, bits 15-0) to uniquely identify the addin board or subsystem the Am79C978 controller is used in. The value of SID is up to the system vendor. A value of 0 (the default) indicates that the Am79C978 controller does not support subsystem identification. SID is aliased to the PCI configuration space register Subsystem ID (offset 2Eh). SID This bit is always read accessible. SID is read only. Write operations are ignored. SID is cleared to 0 by H_RESET and is not affected by S_RESET or by setting the STOP bit. BCR25: SRAM Size Register Bit 164 Name Description Reserved locations. Written as zeros and read as undefined. CAUTION: Programming SRAM_BND and SRAM_SIZE to the same value will cause data corruption except in the case where SRAM_SIZE is 0. This bit is always read accessible; write accessible only when the STOP bit is set. SRAM_SIZE is set to 000000b during H_RESET and is unaffected by S_RESET or STOP. BCR26: SRAM Boundary Register Bit Name Description Note: Bits 7-0 in this register are programmable through the EEPROM. 31-8 7-0 Am79C978 RES Reserved locations. Written as zeros and read as undefined. SRAM_BND SRAM Boundary. Specifies the upper 8 bits of the 16-bit address boundary where the receive buffer begins in the SRAM. The transmit buffer in the SRAM begins at address 0 and ends at the address located just before the address specified by SRAM_BND. Therefore, the receive buffer always begins on a 512 byte boundary. The lower bits are assumed to be zeros. SRAM_BND has no effect in the Low Latency Receive mode. 14 LOLATRX Note: The minimum allowed number of pages is four. The Am79C978 controller will not operate correctly with less than four pages of memory per queue. See Table 41 for SRAM_BND programming details. Table 41. SRAM_BND Programming SRAM Addresses Minimum SRAM_BND Address Maximum SRAM_BND Address SRAM_BND [7:0] 04h 13h When the LOLATRX bit is set to 0, the Am79C978 controller will return to a normal receive configuration. The runt packet accept bit (RPA, CSR124, bit 3) must be set when LOLATRX is set. CAUTION: Programming SRAM_BND and SRAM_SIZE to the same value will cause data corruption except in the case where SRAM SIZE is 0. CAUTION: To provide data integrity when switching into and out of the low latency mode, DO NOT SET the FASTSPNDE (CSR7, bit 15) bit when setting the SPND bit. Receive frames WILL be overwritten and the Am79C978 controller may give erratic behavior when it is enable again. The minimum allowed number of pages is four. The Am79C978 controller will not operate correctly in the LOLATRX mode with less than four pages of memory. Read accessible always; write accessible only when the STOP bit is set. SRAM_BND is set to 00000000b during H_RESET and is unaffected by S_RESET or STOP. BCR27: SRAM Interface Control Register Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15 Reserved. Reserved for manufacturing tests. Written as zero and read as undefined. PTR TST Read/Write accessible only when the STOP bit is set. LOLATRX is cleared to 0 after H_RESET or S_RESET and is unaffected by STOP. Note: Use of this bit will cause data corruption and erroneous operation. This bit is always read/write accessible. PTR_TST is set to 0 by H_RESET and is unaffected by S_RESET and the STOP bit. Low Latency Receive. When the LOLATRX bit is set to 1, the Am79C978 controller will switch to an architecture applicable to cut-through switches. The Am79C978 controller will assert a receive frame DMA after only 16 bytes of the current receive frame has been received regardless of where the RCVFW (CSR80, bits 13-12) are set. The watermark is a fixed value and cannot be changed. The receive FIFOs will be in NO_SRAM mode while all transmit traffic is buffered through the SRAM. This bit is only valid and the low latency receive only enabled when the SRAM_SIZE (BCR25, bits 7-0) bits are non-zero. SRAM_BND (BCR26, bits 70) has no meaning when the Am79C978 controller is in the Low Latency mode. See the section on SRAM Configuration for more details. 13-6 Am79C978 RES Reserved locations. Written as zeros and read as undefined. 165 5-3 EBCS Expansion Bus Clock Source. These bits are used to select the source of the fundamental clock to drive the SRAM and Expansion ROM access cycles. Table 42 shows the selected clock source for the various values of EBCS. Note that the actual frequency that the Expansion Bus access cycles run at is a function of both the EBCS and CLK_FAC (BCR27, bits 2-0) bit field settings. When EBCS is set to either the PCI clock or the Time Base clock, no external clock source is required as the clocks are routed internally and the EBCLK pin should be pulled to VDD through a resistor. clock data, corruption will result. CAUTION: The Time Base Clock will not support 100 Mbps operation and should only be selected in 10 Mbpsonly configurations. CAUTION: The external clock source used to drive the EBCLK pin must be a continuous clock source at all times. 2-0 CLK_FAC Table 42. EBCS Values EBCS 000 001 010 011 1XX Expansion Bus Clock Source CLK pin (PCI Clock) Time Base Clock EBCLK pin Reserved Reserved Table 43. CLK_FAC Values Read accessible always; write accessible only when the STOP bit is set. EBCS is set to 000b (PCI clock selected) during H_RESET and is unaffected by S_RESET or the STOP bit. Note: The clock frequency driving the Expansion Bus access cycles that results from the settings of the EBCS and CLK FAC bits must not exceed 33 MHz at any time. When EBCS is set to either the PCI clock or the Time Base clock, no external clock source is required because the clocks are routed internally and the EBCLK pin should be pulled to VDD through a resistor. CLK_FAC 000 001 010 011 1XX Clock Factor 1 1/2 (divide by 2) Reserved 1/4 (divide by 4) Reserved Read accessible always; write accessible only when the STOP bit is set. CLK_FAC is set to 000b during H_RESET and is unaffected by S_RESET or STOP. BCR28: Expansion Bus Port Address Lower (Used for Flash/EPROM and SRAM Accesses) Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 Expansion Port Address Lower. This address is used to provide addresses for the Flash and SRAM port accesses. CAUTION: Care should be exercised when choosing the PCI clock pin because of the nature of the PCI clock signal. The PCI specification states that the PCI clock can be stopped. If that can occur while it is being used for the Expansion Bus 166 Clock Factor. These bits are used to select whether the clock selected by EBCS is used directly or if it is divided down to give a slower clock for running the Expansion Bus access cycles. The possible factors are given in Table 43. Am79C978 EPADDRL SRAM accesses are started when a read or write is performed on BCR30 and the FLASH (BCR 29, bit 15) is set to 0. During SRAM accesses only bits in the EPADDRL are valid. Since all SRAM accesses are word oriented only, EPADDRL[0] is the least significant word address bit. On any byte write accesses to the SRAM, the user will have to follow the read-modify-write scheme. On any byte read accesses to the SRAM, the user will have to chose which byte is needed from the complete word returned in BCR30. Flash accesses are started when a read or write is performed on BCR30 and the FLASH (BCR 29, bit 15) is set to 1. During Flash accesses all bits in EPADDR are valid. Read accessible always; write accessible only when the STOP is set or when SRAM SIZE (BCR25, bits 7-0) is 0. EPADDRL is undefined after H_RESET and is unaffected by S_RESET or STOP. Port Lower Address (EPADDRL) will roll over to 0000h. When the LAAINC bit is set to 0, the Expansion Port Lower Address will not be affected in any way after an access to EBDATA (BCR30) and must be programmed. This bit is always read accessible; write accessible only when the STOP bit is set. LAINC is 0 after H_RESET and is unaffected by S_RESET or the STOP bit. 13-4 RES Reserved locations. Written as zeros and read as undefined. 3-0 EPADDRU Expansion Port Address Upper. This upper portion of the Expansion Bus address is used to provide addresses for Flash/EPROM port accesses. This bit is always read accessible; write accessible only when the STOP bit is set or when SRAM SIZE (BCR25, bits 7-0) is 0. EPADDRU is undefined after H_RESET and is unaffected by S_RESET or the STOP bit. BCR29: Expansion Port Address Upper (Used for Flash/EPROM Accesses) Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15 Flash Access. When the FLASH bit is set to 1, the Expansion Bus access will be a Flash cycle. When FLASH is set to 0, the Expansion Bus access will be a SRAM cycle. For a complete description, see the section on Expansion Bus Accesses. This bit is only applicable to reads or writes to EBDATA (BCR30). It does not affect Expansion ROM accesses from the PCI system bus. 14 FLASH LAAINC BCR30: Expansion Bus Data Port Register Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 This bit is always read accessible; write accessible only when the STOP bit is set. FLASH is 0 after H_RESET and is unaffected by S_RESET or the STOP bit. Expansion Bus Data Port. EBDATA is the data port for operations on the Expansion Port accesses involving SRAM and Flash accesses. The type of access is set by the FLASH bit (BCR 29, bit 15). When the FLASH bit is set to 1, the Expansion Bus access will follow the Flash access timing. When the FLASH bit is set to 0, the Expansion Bus access will follow the SRAM access timing. Lower Address Auto Increment. When the LAAINC bit is set to 1, the Expansion Port Lower Address will automatically increment by one after a read or write access to EBDATA (BCR30). When EBADDRL reaches FFFFh and LAAINC is set to 1, the Expansion Note: It is important to set the FLASH bit and load Expansion Port Address EPADDR (BCR28, BCR29) with the required address before attempting read or write to the Expansion Bus data port. The Flash and SRAM accesses use different address Am79C978 EBDATA 167 phases. Incorrect configuration will result in a possible corruption of data. The STVAL value is interpreted as an unsigned number with a resolution of 256 Time Base Clock periods. For instance, a value of 122 ms would be programmed with a value of 9531 (253Bh) if the Time Base Clock is running at 20 MHz. A value of 0 is undefined and will result in erratic behavior. Flash read cycles are performed when BCR30 is read and the FLASH bit (BCR29, bit 15) is set to 1. Upon completion of the read cycle, the 8-bit result for Flash access is stored in EBDATA[7:0], EBDATA[15:8] is undefined. Flash write cycles are performed when BCR30 is written and the FLASH bit (BCR29, bit 15) is set to 1. EBDATA[7:0] only is valid for write cycles. SRAM read cycles are performed when BCR30 is read and the FLASH bit (BCR29, bit 15) is set to 0. Upon completion of the read cycle, the 16-bit result for SRAM access is stored in EBDATA. Write cycles to the SRAM are invoked when BCR30 is written and the FLASH bit (BCR29, bit 15) is set to 0. Byte writes to the SRAM must use a read-modifywrite scheme since the word is always valid for SRAM write or read accesses. Read and write accessible always. STVAL is set to FFFFh after H_RESET and is unaffected by S_RESET and the STOP bit. BCR32: PHY Control and Status Register Note: Bits 15-0 in this register are programmable through the EEPROM. Bit Name 31-16 RES Reserved locations. Written as zeros and read as undefined. 15 Reserved for manufacturing tests. Written as 0 and read as undefined. ANTST Note: Use of this bit will cause data corruption and erroneous operation. This bit is read and write accessible only when the STOP is set or when SRAM SIZE (BCR25, bits 7-0) is 0. EBDATA is undefined after H_RESET and is unaffected by S_RESET and the STOP bit. BCR31: Software Timer Register Bit Name 14 Reserved locations. Written as zeros and read as undefined. 15-0 Software Timer Value. STVAL controls the maximum time for the Software Timer to count before generating the STINT (CSR7, bit 11) interrupt. The Software Timer is a free-running timer that is started upon the first write to STVAL. After the first write, the Software Timer will continually count and set the STINT interrupt at the STVAL period. 168 STVAL This bit is always read/write accessible. ANTST is set to 0 by H_RESET and is unaffected by S_RESET and the STOP bit. Description 31-16 RES Description Am79C978 MIIPD MII PHY Detect (is used for manufacturing tests). MIIPD reflects the quiescent state of the MDIO pin. MIIPD is continuously updated whenever there is no management operation in progress on the MII interface. When a management operation begins on the interface, the state of MIIPD is preserved until the operation ends, when the quiescent state is again monitored and continuously updates the MIIPD bit. When the MDIO pin is at a quiescent LOW state, MIIPD is cleared to 0. When the MDIO pin is at a quiescent HIGH state, MIIPD is set to 1. MIIPD is used by the automatic port selection logic to select the MII port. When the Auto Select bit (ASEL, BCR2, bit 1) is a 1 and the MIIPD bit is a 1, the MII port is selected. Any transition on the MIIPD bit will set the MIIPDTI bit in CSR7, bit 3. 10-8 Read accessible always. MIIPD is read only. Write operations are ignored and should not be performed. 13-12 FMDC Fast Management Data Clock (is used for manufacturing tests). When FMDC is set to 1h, the MII Management Data Clock will run at 5 MHz max. The Management Data Clock will no longer be IEEE 802.3u-compliant and setting this bit should be used with care. The accompanying external PHY must also be able to accept management frames at the new clock rate. When FMDC is set to 0h, the MII Management Data Clock will run at 2.5 MHz max and will be fully compliant to IEEE 802.3u standards. See Table 44. APDW Table 45. APDW Values APDW 000 001 010 011 100 101 Auto-Poll Dwell Time Continuous (26s @ 2.5 MHz) Every 128 MDC cycles (103s @ 2.5 MHz) Every 256 MDC cycles (206s @ 2.5 MHz) Every 512 MDC cycles (410 s @ 2.5 MHz) Every 1024 MDC cycles (819 s @ 2.5 MHz) Every 2048 MDC cycles (1640 s @ 2.5 MHz) 110-111 Reserved This bit is always read/write accessible. APDW is set to 100h after H_RESET and is unaffected by S_RESET and the STOP bit. 7 DANAS Table 44. FMDC Values FMDC 00 01 10 11 Fast Management Data Clock 2.5 MHz max 5 MHz max Reserved Reserved This bit is always read/write accessible. FMDC is set to 0 during H_RESET, and is unaffected by S_RESET and the STOP bit 11 APEP Auto-Poll PHY. When APEP is set to 1 the Am79C978 controller will poll the status register in the PHY. This feature allows the software driver or upper layers to see any changes in the status of the PHY. An interrupt when enabled is generated when the contents of the new status is different from the previous status. Auto-Poll Dwell Time. APDW determines the dwell time between PHY Management Frame accesses when Auto-Poll is turned on. See Table 45. Disable Auto-Negotiation Auto Setup. When DANAS is set, the Am79C978 controller after a H_RESET or S_RESET will remain dormant and not automatically startup the Auto-Negotiation section or the enhanced automatic port selection section. Instead, the Am79C978 controller will wait for the software driver to setup the Auto-Negotiation portions of the device. The PHY Address and Data programming in BCR33 and BCR34 is still valid. The Am79C978 controller will not generate any management frames unless Auto-Poll is enabled. This bit is always read/write accessible. DANAS is set to 0 by H_RESET and is unaffected by S_RESET and the STOP bit. 6 This bit is always read/write accessible. APEP is set to 0 during H_RESET and is unaffected by S_RESET and the STOP bit. Am79C978 XPHYRST PHY Reset. When XPHYRST is set, the Am79C978 controller after an H_RESET or S_RESET will issue management frames that will reset the PHY. This bit is needed when there is no way to guarantee the state of the external PHY. This bit must be reprogrammed after every H_RESET. 169 This bit is always read/write accessible. XPHYRST is set to 0 by H_RESET and is unaffected by S_RESET and the STOP bit. XPHYRST is only valid when the internal Network Port Manager is scanning for a network port. 5 XPHYANE PHY Auto-Negotiation Enable. This bit will force the PHY into enabling Auto-Negotiation. When set to 0 the Am79C978 controller will send a management frame disabling Auto-Negotiation. This bit is always read/write accessible. XPHYANE is set to 0 by H_RESET and is unaffected by S_RESET and the STOP bit. XPHYANE is only valid when the internal Network Port Manager is scanning for a network port. 4 XPHYFD XPHYSP 0 RES Reserved location. Written as zero and read as undefined. BCR33: PHY Address Register Bit Name Description Reserved locations. Written as zeros and read as undefined. 15 SHADOW If the user wishes to update the contents of the BCR33 shadow register, setting the MSB of the value written into BCR33 (bit 15) will enable the contents to be simultaneously written to BCR33 shadow. 14 MII_SEL MII selected. This bit indicates whether the internal PHY is selected. PHY Speed. When set, this bit will force the PHY into 100 Mbps mode when Auto-Negotiation is not enabled. 13 AUTONEG_COMPLETE This bit is always read/write accessible. XPHYSP is set to 0 by H_RESET, and is unaffected by S_RESET and the STOP bit. 12 11 PHY Full Duplex. When set, this bit will force the PHY into full duplex when Auto-Negotiation is not enabled. 2 RES Reserved location. Written as zero and read as undefined. 1 MIIILP Media Independent Interface Internal Loopback. When set, this bit will cause the internal portion of the MII data port to loopback on itself. The interface is mapped in the following way. The TXD[3:0] nibble data path is looped back onto the RXD[3:0] nibble data path. TX_CLK is looped back as RX_CLK. TX_EN is looped back as RX_DV. CRS is correctly OR'd with TX_EN and RX_DV and always encompass- 170 This bit is always read/write accessible. MIIILP is set to 0 by H_RESET and is unaffected by S_RESET and the STOP bit. 31-16 RES This bit is always read/write accessible. XPHYFD is set to 0 by H_RESET, and is unaffected by S_RESET and the STOP bit. 3 es the transmit frame. TX_ER is looped back as RX_ER. However, TX_ER will not get asserted by the Am79C978 controller to signal an error. The TX_ER function is reserved for future use. Internal Auto-Negotiation complete. Valid for internal PHY only. LINK STATUS Link Status. This bit is a valid link status indication. FULL_DUPLEX Full Duplex. This bit indicates that the MAC is configured for FullDuplex operation. 10 SPEED_SEL Speed Selected. This bit indicates if High or Low speed has been selected by MAC. 9-5 PHYAD Am79C978 Management Frame PHY Address. PHYAD contains the 5-bit PHY Address field that is used in the management frame that gets clocked out via the MII management port pins (MDC and MDIO) whenever a read or write transaction occurs to BCR34. The PHY address 1Fh is not valid. ten to MIIMD is the value used in the data field of the management write frame. The Network Port Manager copies the PHYAD after the Am79C978 controller reads the EEPROM and uses it to communicate with the external PHY. The PHY address must be programmed into the EEPROM prior to starting the Am79C978 controller. These bits are always read/write accessible. MIIMD is undefined after H_RESET and is unaffected by S_RESET and the STOP bit. These bits are always read/write accessible. PHYAD is undefined after H_RESET and is unaffected by S_RESET and the STOP bit. 4-0 REGAD BCR35: PCI Vendor ID Register Note: Bits 15-0 in this register are programmable through the EEPROM. Bit Reserved locations. Written as zeros and read as undefined. 15-0 Vendor ID. The PCI Vendor ID register is a 16-bit register that identifies the manufacturer of the Am79C978 controller. AMD's Vendor ID is 1022h. Note that this Vendor ID is not the same as the Manufacturer ID in CSR88 and CSR89. The Vendor ID is assigned by the PCI Special Interest Group. Management Frame Register Address. REGAD contains the 5-bit Register Address field that is used in the management frame that gets clocked out via the internal MII management interface whenever a read or write transaction occurs to BCR34. BCR34: PHY Management Data Register Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-0 MII Management Data. MIIMD is the data port for operations on the MII management interface (MDIO and MDC). The Am79C978 controller builds management frames using the PHYAD and REGAD values from BCR33. The operation code used in each frame is based upon whether a read or write operation has been performed to BCR34. Read cycles on the MII management interface are invoked when BCR34 is read. Upon completion of the read cycle, the 16-bit result of the read operation is stored in MIIMD. Write cycles on the MII management interface are invoked when BCR34 is written. The value writ- MIIMD Description 31-16 RES These bits are always read/write accessible. REGAD is undefined after H_RESET and is unaffected by S_RESET and the STOP bit. Bit Name Am79C978 VID The Vendor ID is not normally programmable, but the Am79C978 controller allows this due to legacy operating systems that do not look at the PCI Subsystem Vendor ID and the Vendor ID to uniquely identify the add-in board or subsystem that the Am79C978 controller is used in. Note: If the operating system or the network operating system supports PCI Subsystem Vendor ID and Subsystem ID, use those to identify the add-in board or subsystem and program the VID with the default value of 1022h. VID is aliased to the PCI configuration space register Vendor ID (offset 00h). Read accessible always. VID is read only. Write operations are ignored. VID is set to 1022h by H_RESET and is not affected by S_RESET or by setting the STOP bit. 171 BCR36: PCI Power Management Capabilities (PMC) Alias Register BCR38: PCI DATA Register 1 (DATA1) Alias Register Note: This register is an alias of the PMC register located at offset 42h of the PCI Configuration Space. Since PMC register is read only, BCR36 provides a means of programming it through the EEPROM. The contents of this register are copied into the PMC register. For the definition of the bits in this register, refer to the PMC register definition. Bits 15-0 in this register are programmable through the EEPROM. Read accessible always. Read only. Cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. Note: This register is an alias of the DATA register and also of the DATA_SCALE field of the PMCSR register. Since these two are read only, BCR38 provides a means of programming them through the EEPROM. The contents of this register are copied into the corresponding fields pointed with the DATA_SEL field set to one. Bits 15-0 in this register are programmable through the EEPROM. Bit Name 15-10 RES BCR37: PCI DATA Register 0 (DATA0) Alias Register Note: This register is an alias of the DATA register and also of the DATA_SCALE field of the PMCSR register. Since these two are read only, BCR37 provides a means of programming them indirectly. The contents of this register are copied into the corresponding fields pointed with the DATA_SEL field set to zero. Bits 15-0 in this register are programmable through the EEPROM. Bit Name 15-10 RES 9-8 9-8 These bits are always read accessible. D1_SCALE is read only. Cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. Reserved locations. Written as zeros and read as undefined. 7-0 DATA1 DATA0 These bits correspond to the PCI DATA register (offset Register 47 of the PCI configuration space, bits 7-0). Refer to the description of DATA register for the meaning of this field. This bit is always read accessible. DATA0 is read only. Cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. BCR39: PCI DATA Register 2 (DATA2) Alias Register Note: This register is an alias of the DATA register and also of the DATA_SCALE field of the PMCSR register. Since these two are read only, BCR39 provides a means of programming them through the EEPROM. The contents of this register are copied into the corresponding fields pointed with the DATA_SEL field set to two. Bits 15-0 in this register are programmable through the EEPROM. Bit Name 15-10 RES 172 These bits correspond to the PCI DATA register (offset Register 47 of the PCI configuration space, bits 7-0). Refer to the description of DATA register for the meaning of this field. These bits are always read accessible. DATA1 is read only. Cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. Read accessible always. D0_SCALE is read only. Cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 7-0 Reserved locations. Written as zeros and read as undefined. D1_SCALE These bits correspond to the DATA_SCALE field of the PMCSR (offset Register 44 of the PCI configuration space, bits 14-13). Refer to the description of DATA_SCALE for the meaning of this field. Description D0_SCALE These bits correspond to the DATA_SCALE field of the PMCSR (offset Register 44 of the PCI configuration space, bits 1413). Refer to the description of DATA_SCALE for the meaning of this field. Description Am79C978 Description Reserved locations. Written as zeros and read as undefined. 9-8 D2_SCALE These bits correspond to the DATA_SCALE field of the PMCSR (offset Register 44 of the PCI configuration space, bits 1413). Refer to the description of DATA_SCALE for the meaning of this field. 7-0 DATA3 These bits are always read accessible. DATA3 is read only. Cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. These bits are always read accessible. D2_SCALE is read only. Cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 7-0 DATA2 These bits correspond to the PCI DATA register (offset Register 47 of the PCI configuration space, bits 7-0). Refer to the description of DATA register for the meaning of this field. These bits are always read accessible. DATA2 is read only. Cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. BCR40: PCI DATA Register 3 (DATA3) Alias Register Bit Name 15-10 RES 9-8 BCR41: PCI DATA Register 4 (DATA4) Alias Register Note: This register is an alias of the DATA register and also of the DATA_SCALE field of the PCMCR register. Since these two are read only, BCR41 provides a means of programming them through the EEPROM. The contents of this register are copied into the corresponding fields pointed with the DATA_SEL field set to four. Bits 15-0 in this register are programmable through the EEPROM. Bit Name 15-10 RES Note: This register is an alias of the DATA register and also of the DATA_SCALE field of the PCMCR register. Since these two are read only, BCR40 provides a means of programming them through the EEPROM. The contents of this register are copied into the corresponding fields pointed with the DATA_SEL field set to three. Bits 15-0 in this register are programmable through the EEPROM. These bits correspond to the PCI DATA register (offset Register 47 of the PCI configuration space, bits 7-0). Refer to the description of DATA register for the meaning of this field. 9-8 Description Reserved locations. Written as zeros and read as undefined. D4_SCALE These bits correspond to the DATA_SCALE field of the PMCSR (offset register 44 of the PCI configuration space, bits 14-13). Refer to the description of DATA_SCALE for the meaning of this field. Description Read accessible always. D4_SCALE is read only. Cleared by H_RESET and is not affected by S_RESET or setting the STOP bit Reserved locations. Written as zeros and read as undefined. D3_SCALE These bits correspond to the DATA_SCALE field of the PMCSR (offset Register 44 of the PCI configuration space, bits 14-13). Refer to the description of DATA_SCALE for the meaning of this field. 7-0 These bits are always read accessible. D3_SCALE is read only. Cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. Am79C978 DATA4 These bits correspond to the PCI DATA register (offset Register 47 of the PCI configuration space, bits 7-0). Refer to the description of DATA register for the meaning of this field. Read accessible always. DATA4 is read only. Cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 173 BCR42: PCI DATA Register 5 (DATA5) Alias Register 9-8 Note: This register is an alias of the DATA register and also of the DATA_SCALE field of the PCMCR register. Since these two are read only, BCR42 provides a means of programming them through the EEPROM. The contents of this register are copied into the corresponding fields pointed with the DATA_SEL field set to five. Bits 15-0 in this register are programmable through the EEPROM. Bit Name 15-10 RES 9-8 These bits are always read accessible. D6_SCALE is read only. Cleared by H_RESET and is not affected by S_RESET or setting the STOP bit Description Reserved locations. Written as zeros and read as undefined. 7-0 DATA5 These bits correspond to the PCI DATA register (offset Register 47 of the PCI configuration space, bits 7-0). Refer to the description of DATA register for the meaning of this field. These bits are always read accessible. DATA5 is read only. Cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. BCR44: PCI DATA Register 7 (DATA7) Alias Register Note: This register is an alias of the DATA register and also of the DATA_SCALE field of the PCMCR register. Since these two are read only, BCR44 provides a means of programming them through the EEPROM. The contents of this register are copied into the corresponding fields pointed with the DATA_SEL field set to seven. Bits 15-0 in this register are programmable through the EEPROM. Bit 15-10 RES 174 Name 15-10 RES Note: This register is an alias of the DATA register and also of the DATA_SCALE field of the PCMCR register. Since these two are read only, BCR43 provides a means of programming them through the EEPROM. The contents of this register are copied into the corresponding fields pointed with the DATA_SEL field set to six. Bits 15-0 in this register are programmable through the EEPROM. Name Description Reserved locations. Written as zeros and read as undefined. D7_SCALE These bits correspond to the DATA_SCALE field of the PMCSR (offset Register 44 of the PCI configuration space, bits 14-13). Refer to the description of DATA_SCALE for the meaning of this field. These bits are always read accessible. D7_SCALE is read only. Cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. Description Reserved locations. Written as zeros and read as undefined. These bits correspond to the PCI DATA register (offset Register 47 of the PCI configuration space, bits 7-0). Refer to the description of DATA register for the meaning of this field. These bits are always read accessible. DATA6 is read only. Cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 9-8 BCR43: PCI DATA Register 6 (DATA6) Alias Register Bit DATA6 D5_SCALE These bits correspond to the DATA_SCALE field of the PMCSR (offset Register 44 of the PCI configuration space, bits 14-13). Refer to the description of DATA_SCALE for the meaning of this field. These bits are always read accessible. D5_SCALE is read only. Cleared by H_RESET and is not affected by S_RESET or setting the STOP bit 7-0 D6_SCALE These bits correspond to the DATA_SCALE field of the PMCSR (offset Register 44 of the PCI configuration space, bits 14-13). Refer to the description of DATA_SCALE for the meaning of this field. 7-0 Am79C978 DATA7 These bits correspond to the PCI DATA register (offset register 47 of the PCI configuration space, bits 7-0). Refer to the description of DATA register for the meaning of this field. unaffected by S_RESET and the STOP bit. 6-0 PMR_ADDR These bits are always read accessible. DATA7 is read only. Cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. These bits are read and write accessible always. PMR_ADDR is reset to 0 after H_RESET, and is unaffected by S_RESET and the STOP bit. BCR45: OnNow Pattern Matching Register 1 Note: This register is used to control and indirectly access the Pattern Match RAM (PMR). When BCR45 is written and the PMAT_MODE bit (bit 7) is 1, Pattern Match logic is enabled. No bus accesses into PMR are possible, and BCR46, BCR47, and all other bits in BCR45 are ignored. When PMAT_MODE is set, a read of BCR45, BCR46, or BCR47 returns all undefined bits except for PMAT_MODE. When BCR45 is written and the PMAT_MODE bit is 0, the Pattern Match logic is disabled and accesses to the PMR are possible. Bits 6-0 of BCR45 specify the address of the PMR word to be accessed. Following the write to BCR45, the PMR word may be read by reading BCR45, BCR46 and BCR47 in any order. To write to PMR word, the write to BCR45 must be followed by a write to BCR46 and a write to BCR47 in that order to complete the operation. The RAM will not actually be written until the write to BCR47 is complete. The write to BCR47 causes all 5 bytes (four bytes of BCR46-47 and the upper byte of the BCR45) to be written to whatever PMR word is addressed by bits 6:0 of BCR45. Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-8 Pattern Match RAM Byte 0. This byte is written into or read from Byte 0 of the Pattern Match RAM. PMR_B0 BCR46: OnNow Pattern Matching Register 2 Note: This register is used to control and indirectly access the Pattern Match RAM (PMR). When BCR45 is written and the PMAT_MODE bit (bit 7) is 1, Pattern Match logic is enabled. No bus accesses into PMR are possible, and BCR46, BCR47, and all other bits in BCR45 are ignored. When PMAT_MODE is set, a read of BCR45, BCR46, or BCR47 returns all undefined bits except for PMAT_MODE. When BCR45 is written and the PMAT_MODE bit is 0, the Pattern Match logic is disabled and accesses to the PMR are possible. Bits 6-0 of BCR45 specify the address of the PMR word to be accessed. Following the write to BCR45, the PMR word may be read by reading BCR45, BCR46 and BCR47 in any order. To write to PMR word, the write to BCR45 must be followed by a write to BCR46 and a write to BCR47 in that order to complete the operation. The RAM will not actually be written until the write to BCR47 is complete. The write to BCR47 causes all 5 bytes (four bytes of BCR46-47 and the upper byte of the BCR45) to be written to whatever PMR word is addressed by bits 6:0 of BCR45. Bit Name Pattern Match Mode. Writing a 1 to this bit will enable Pattern Match Mode and should only be done after the Pattern Match RAM has been programmed. Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15-8 Pattern Match RAM Byte 2. This byte is written into or read from Byte 2 of the Pattern Match RAM. PMR_B2 These bits are read and write accessible always. PMR_B0 is undefined after H_RESET, and is unaffected by S_RESET and the STOP bit. 7 PMAT_MODE Pattern Match Ram Address. These bits are the Pattern Match Ram address to be written to or read from. These bits are read and write accessible always. PMR_B2 is undefined after H_RESET, and is unaffected by S_RESET and the STOP bit. 7-0 These bits are read and write accessible always. PMAT_MODE is reset to 0 after H_RESET, and is Am79C978 PMR_B1 Pattern Match RAM Byte 1. This byte is written into or read from Byte 1 of Pattern Match RAM. These bits are read and write accessible always. PMR_B1 is un- 175 defined after H_RESET, and is unaffected by S_RESET and the STOP bit. BCR47: OnNow Pattern Matching Register 3 Note: This register is used to control and indirectly access the Pattern Match RAM (PMR). When BCR45 is written and the PMAT_MODE bit (bit 7) is 1, Pattern Match logic is enabled. No bus accesses into PMR are possible, and BCR46, BCR47, and all other bits in BCR45 are ignored. When PMAT_MODE is set, a read of BCR45, BCR46, or BCR47 returns all undefined bits except for PMAT_MODE. When BCR45 is written and the PMAT_MODE bit is 0, the Pattern Match logic is disabled and accesses to the PMR are possible. Bits 6-0 of BCR45 specify the address of the PMR word to be accessed. Following the write to BCR45, the PMR word may be read by reading BCR45, BCR46 and BCR47 in any order. To write to PMR word, the write to BCR45 must be followed by a write to BCR46 and a write to BCR47 in that order to complete the operation. The RAM will not actually be written until the write to BCR47 is complete. The write to BCR47 causes all 5 bytes (four bytes of BCR46-47 and the upper byte of the BCR45) to be written to whatever PMR word is addressed by bits 6:0 of BCR45. BCR48: LED4 Status This register defines the functionality of LED4. LED4 will default to indicating the selected SPEED with Pulse stretching enabled (default = 0082h). BCR48 controls the function(s) that the LED4 pin displays. Multiple functions can be simultaneously enabled on this LED pin. The LED display will indicate the logical OR of the enabled functions. Note: When LEDPE (BCR2, bit 12) is set to 1, programming of the LED2 Status register is enabled. When LEDPE is cleared to 0, programming of the LED2 register is disabled. Writes to those registers will be ignored. Note: Bits 15-0 in this register are programmable through the EEPROM PREAD operation. Bit Name 31-16 RES Reserved locations. Written as zeros and read as undefined. 15 This bit indicates the current (non-stretched) value of the LED output pin. A value of 1 in this bit indicates that the OR of the enabled signals is true. LEDOUT When PMAT_MODE is 0, the contents of the word addressed by bits 6:0 of BCR45 can be read by reading BCR45-47 in any order. Bit Name Reserved locations. Written as zeros and read as undefined. 15-8 Pattern Match RAM Byte 4. This byte is written into or read from Byte 4 of Pattern Match RAM. PMR_B4 The logical value of the LEDOUT status signal is determined by the settings of the individual Status Enable bits of the LED register (bits 8 and 6-0). Description 31-16 RES Read accessible always. This bit is read only; writes have no effect. LEDOUT is unaffected by H_RESET, S_RESET, or STOP. 14 These bits are read and write accessible always. PMR_B4 is undefined after H_RESET, and is unaffected by S_RESET and the STOP bit. 7-0 PMR_B3 Pattern Match RAM Byte 3. This byte is written into or read from Byte 3 of Pattern Match RAM. These bits are read and write accessible always. PMR_B3 is undefined after H_RESET, and is unaffected by S_RESET and the STOP bit. 176 Description Am79C978 LEDPOL LED Polarity. When this bit has the value 0, then the LED pin will be driven to a LOW level whenever the OR of the enabled signals is true, and the LED pin will be disabled and allowed to float high whenever the OR of the enabled signals is false (i.e., the LED output will be an Open Drain output and the output value will be the inverse of the LEDOUT status bit). When this bit has the value 1, then the LED pin will be driven to a HIGH level whenever the OR of the enabled signals is true, and the LED pin will be driven to a LOW level whenever the OR of the enabled signals is false (i.e., the LED output will be a Totem Pole output and the output value will be the same polarity as the LEDOUT status bit). 8 FDLSE The setting of this bit will not effect the polarity of the LEDOUT bit for this register. This bit is always read/write accessible. LEDPOL is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 13 LEDDIS LED Disable. This bit is used to disable the LED output. When LEDDIS has the value 1, then the LED output will always be disabled. When LEDDIS has the value 0, then the LED output value will be governed by the LEDOUT and LEDPOL values. This bit is always read/write accessible. FDLSE is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 7 PSE This bit is always read/write accessible. LEDDIS is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 12 100E 100 Mbps Enable. When this bit is set to 1, a value of 1 is passed to the LEDOUT bit in this register when the Am79C978 controller is operating in 100 Mbps mode. Reserved locations. Written and read as zeros. 9 Magic Packet Status Enable. When this bit is set to 1, a value of 1 is passed to the LEDOUT bit in this register when Magic Packet frame mode is enabled and a Magic Packet frame is detected on the network. MPSE Pulse Stretcher Enable. When this bit is set, the LED illumination time is extended for each new occurrence of the enabled function for this LED output. A value of 0 disables the pulse stretcher. This bit is always read/write accessible. PSE is set to 1 by H_RESET and is not affected by S_RESET or setting the STOP bit. 6 LNKSE This bit is always read/write accessible. 100E is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 11-10 RES Full-Duplex Link Status Enable. Indicates the Full-Duplex Link Test Status. When this bit is set, a value of 1 is passed to the LEDOUT signal when the Am79C978 controller is functioning in a Link Pass state and full-duplex operation is enabled. When the Am79C978 controller is not functioning in a Link Pass state with full-duplex operation being enabled, a value of 0 is passed to the LEDOUT signal. Link Status Enable. When this bit is set, a value of 1 will be passed to the LEDOUT bit in this register in Link Pass state. This bit is always read/write accessible. LNKSE is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 5 This bit is always read/write accessible. MPSE is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. Am79C978 RCVME Receive Match Status Enable. When this bit is set, a value of 1 is passed to the LEDOUT bit in this register when there is receive activity on the network that has passed the address match function for this node. All address matching modes are included: physical, logical filtering, broadcast, and promiscuous. This bit is always read/write accessible. RCVME is cleared by H_RESET and is not affected by 177 S_RESET or setting the STOP bit. 4 XMTE Transmit Status Enable. When this bit is set, a value of 1 is passed to the LEDOUT bit in this register when there is transmit activity on the network. This bit is always read/write accessible. XMTE is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. 3 2 POWER RCVE Power. When this bit is set to 1, the device is operating in HIGH power mode. 0 SPEED COLE This register defines which PHY will be able to send and receive data over the MII interface. Bits 15:8 are updated whenever the EEPROM is read, and bits 6:0 are updated only if bit 7 is cleared. The bits are defined as follows: Bit Name 15 PC_NET 14-10 RES 9-8 Speed. When this bit is set to 1, the device is operating in HIGH speed mode. Collision Status Enable. When this bit is set, a value of 1 is passed to the LEDOUT bit in this register when there is collision activity on the network. This bit is always read/write accessible. COLE is cleared by H_RESET and is not affected by S_RESET or setting the STOP bit. Description PCnet mode. This bit must always be set. Reserved locations. These bits must be written as zeros. PHY_SEL_Default PHY Select Default. These bits store the desired default PHY. These bits have no effect on the operation of the device and are provided only as a storage location. Receive Status Enable. When this bit is set, a value of 1 is passed to the LEDOUT bit in this register when there is receive activity on the network. This bit is always read/write accessible. RCVE is set to 1 by H_RESET and is not affected by S_RESET or setting the STOP bit. 1 BCR49: PHY Select 7 PHY_SEL_Lock PHY Select Lock. Setting this bit prevents the PHY_SEL bits from being overwritten by subsequent soft resets. The user may write this bit at any time. It is cleared during Power-On Reset. 6-2 RES Reserved. Must be written as zero. 1-0 PHY_SEL PHY Select. These bits define the active PHY as follows: 00 10BASE-T PHY 01 HomePNA PHY 10 External PHY 11 Reserved/Undefined BCR50-BCR55: Reserved Locations These registers must be 00h. 178 Am79C978 1 Mbps HomePNA PHY Internal Registers BCR33, and BCR34) in the integrated PCnet controller to control and communicate to the HomePNA PHY via the MDC and MDIO signals. The registers of the HomePNA PHY are accessible via the internal MII interface. This interface uses the MII Control, Address, and Data Registers (BCR32, See Table 46 through Table 63. HPR0: HomePNA PHY MII Control (Register 0) Table 46. Bits HPR0: HomePNA PHY MII Control (Register 0) Mnemonic Description Read/ Write Default Hex Soft Reset R/W 0 0 R/W 0 0 R 0 0 R/W 0 0 R/W 0 0 R/W 1 1 R/W 0 0 R/W 0 0 MII_CONTROL 1 = RESET 15 RESET 0 = Normal operation ** Self Clearing 14 Loopback 13 Speed Selection 12 Auto-Negotiation Enabled 1 = MII Loopback enabled 0 = MII Loopback disabled 0 = 10 Mbps 1 = Enabled 0 = Disabled 1 = Power down 11 Power Down 0 = Normal operation (This bit is mirrored in PHY Control bit 4) 10 Isolate 9 Restart Auto-Negotiation 1 = Electrically isolate PHY from MII 0 = Normal operation 1 = Restart Auto-Negotiation 0 = Normal operation ** Self Clearing 1 = Full-Duplex (for test purposes only) 8 Duplex Mode 7 Collision Test 0 = Disable COL test signal R/W 0 0 Reserved Write as 0, Ignore Read R/W 0 0 6:0 0 = Half-Duplex Am79C978 179 HPR1: HomePNA PHY MII Status (Register 1) Table 47. HPR1: HomePNA PHY MII Status (Register 1) Bits Mnemonic Description Read/ Write Default Hex Soft Reset MII_Status 15 100BASE-T4 0 = PHY not able to perform 100BASE-T4 R 0 0 14 100BASE-X Full-Duplex 0 = PHY not able to perform Full-Duplex 100BASE-X R 0 0 13 100BASE-X Half-Duplex 0 = PHY not able to perform Half-Duplex 100BASE-X R 0 0 12 10 Mbps Full-Duplex 0 = PHY not able to perform 10 Mbps in FullDuplex R 0 0 11 10 Mbps Half-Duplex 1 = PHY able to perform 10 Mbps in HalfDuplex R 1 1 Reserved Reads will produce undefined results R R 1 1 R 0 0 R 0 0 R 0 0 R 0 0 R 0 0 R 1 1 10:7 6 MF Preamble Suppression 5 Auto-Negotiation Complete 4 Remote Fault 3 Auto-Negotiation Ability 1 = PHY will accept management frames with Preamble suppressed 0 = PHY will not accept management frames with Preamble suppressed 1 = Auto-Negotiation completed 0 = Auto-Negotiation not completed 1 = Remote fault detected 0 = Normal operation 1 = PHY is able to perform Auto-Negotiation 0 = PHY is not able to perform Auto-Negotiation 1 = Link is up 0 = Link is down 180 2 Link Status 1 Jabber Detect 0 Extended Capability This bit will be RESET (latched low and reenabled on Read) on the first occurrence of lost link and will be SET after completion of valid LINK process. 1 = Jabber condition detected 0 = Normal operation 1 = Extended Register Capability 0 = Basic Register Set Capability Am79C978 HPR2 and HPR3: HomePNA PHY MII PHY ID (Registers 2 and 3) Table 48. HPR2 and HPR3: HomePNA PHY MII ID (Registers 2 and 3) Description Read/ Write Default Hex Soft Reset Most significant bytes of the PHY_ID (Bits 3-18) R 0000 0000 PHY_ID LSB (15-10) IEEE Address (Bits 19-24) R 1A 1A 9:4 PHY_ID LSB (9-4) Manufacturer Model Number R 39 39 3:0 PHY_ID LSB (3-0) Revision Number R 0 0 Read/ Write Default Hex Soft Reset Bits Mnemonic MII_PHY_ID 15:0 PHY_ID MSB (31-16) MII_PHY_ID 15:10 HPR4-HPR7: HomePNA PHY Auto-Negotiation (Registers 4 - 7) Table 49. HPR4-HPR7: HomePNA PHY Auto-Negotiation (Registers 4 - 7) Hex Mnemonic Description 04 Auto-Negotiation Register 4 Advertisement R 0021 0021 05 Auto-Negotiation Register 5 Link Partner Ability R 0000 0000 06 Auto-Negotiation Register 6 Expansion R 0000 0000 07 Auto-Negotiation Register 7 Next Page R 0000 0000 Reserved Registers: HPR8 - HPR15 These registers should be ignored when read and should not be written to at any time. Am79C978 181 HPR16: HomePNA PHY Control (Register 16) Table 50. Bits HPR16: HomePNA PHY Control (Register 16) Mnemonic Description Read/ Write Default Hex Soft Reset R/W 0 0 R/W 0 0 R/W 0 0 R/W 0 0 R/W 0 0 R/W 0 0 R/W 0 0 R/W 0 0 R 0 0 R 1 1 R 0 0 PHY_Control 15 14:12 Remote Command Reserved 11 Command Low Power 10 Command High Power 9 Command Low Speed 8 Command High Speed 7 Disable AID Negotiation 6 Clear PHY-Event Counter 5 Disable Squelch adaptation 1 = Ignore Remote Commands 0 = Normal operation Reads will produce undefined results 1 = Command low power 0 = Normal operation 1 = Command high power 0 = Normal operation 1 = Command low speed 0 = Normal operation 1 = Command high speed 0 = Normal operation 1 = Disable AID negotiation 0 = Normal operation 1 = Clear PHY event counter 0 = Normal operation 1 = Disable Squelch adaptation 0 = Normal operation R/W 1 = Power down 4 Power Down 0 = Normal operation (This bit is controlled by HPR0) 182 3 Reserved 2 High Speed 1 High Power 0 Reserved Reads will produce undefined results 1 = Set node to High speed 0 = Set node to Low speed 1 = Set node to High power 0 = Set node to Low power Reads will produce undefined results Am79C978 R R/W HPR17: HomePNA Status Control (Register 17) Table 51. HPR17: HomePNA Status Control (Register 17) Bits Mnemonic 15:13 Reserved 12 Any1home 11:7 Reserved Description Reads will produce undefined results; Writes = 0 1 = Any1Home Link Packet Disable 0 = Any1Home Link Packet Enable Reads will produce undefined results; Writes = 0 1 = Last packet received was sent at high power 6 Received_Power 5 Received_Speed 4 Received_Ver 1 = Last packet received was sent at Version XX Reserved Reads will produce undefined results; Writes = 0 3:0 0 = Last packet received was sent at low power 1 = Last packet received was sent at high power 0 = Last packet received was sent at low power Read/ Write Default Hex Soft Reset R/W R/W 0 R/W R 0 R 0 R 0 R/W HPR18 and HPR19: HomePNA PHY TxCOMM (Registers 18 and 19) Table 52. HPR18 and HPR19: HomePNA PHY TxCOMM (Registers 18 and 19) Hex 12-13 Mnemonic PHY_TX_COMM (4) Description The 32-bit preamble transmitted on the HomePNA PHY. Register 12 contains the high word and Register 13 the low word. The 32-bit transmitted data field is to be used for outof-band communication between PHY management entities. No protocol for out-of-band management has been defined. Accessing the low word causes the PHY to send all-0 PCOMs until the high word has been accessed. Once accessed, the next transmitted packet will cause this register's contents to be shifted out in Read/ Write Default Hex Soft Reset R/W All 0s All 0s the PCOM field of the transmitted packet. Upon transmission, this register will read back as all 0s. A non-null transmitted PCOM will set the TxPCOM Ready bit in the Event Status Register (Register HPR26). An access to any of the two TxPCOM words will clear the TxPCOM Ready bit in the ISTAT register. Am79C978 183 HPR20 and HPR21: HomePNA PHY RxCOMM (Registers 20 and 21) Table 53. Hex 14-15 HPR20 and HPR21: HomePNA PHY RxCOMM (Registers 20 and 21) Mnemonic PHY_RX_COMM (4) Description The 32-bit preamble received on the HomePNA PHY. Register 14 contains the high word and Register 15 the low word. The 32-bit received data field to be used for out-ofband communication between PHY management entities. No protocol for out-of-band management has been defined. Accessing the low word of the register is sufficient to ensure that subsequently received packets will not over-write the register contents. A non-null re- Read/ Write Default Hex Soft Reset R All 0s All 0s ceived PCOM will set the RxPCOM Valid bit of the Event Status Register (Register HPR26). Accessing the high word of the register clears this bit and allows over-writing of the register by subsequent received packets. HPR22: HomePNA PHY AID (Register 22) Table 54. HPR22: HomePNA PHY AID (Register 22) Bits Mnemonic Description Read/ Write Default Hex Soft Reset R/W 00 00 R/W 00 00 PHY_AID The Address ID of this PHY 15:8 7:0 PHY_AID If PHY_Control Disable AID Negotiation is not set then writes to this bit will have no effect. An 8-bit counter that records the number of noise events detected. Overflows are held as FFh. Can be cleared by setting bit 6 of the control register. Noise Events The PHY's AID address is used for collision detection. Unless bit 7 of the CONTROL register is set, the PHY is assured to select a unique AID address. Addresses above EFh are reserved. Address FFh is defined to indicate a remote command. HPR23: HomePNA PHY Noise Control (Register 23) Table 55. Bits Mnemonic HPR23: HomePNA PHY Noise Control (Register 23) Description Read/ Write Default Hex Soft Reset PHY_NOISE_CTRL1 15:8 Noise Floor The minimum value of the NOISE measurement. R/W 03 03 7:0 Noise Ceiling The maximum value if the NOISE measurement. If it is exceeded, NOISE is reset to the FLOOR. R/W FF FF 184 Am79C978 HPR24: HomePNA PHY Noise Control 2 (Register 24) Table 56. HPR24: HomePNA PHY Noise Control 2 (Register 24) Bits Mnemonic Description Read/ Write Default Hex Soft Reset R/W F4 F4 Read/ Write Default Hex Soft Reset R/W 03 03 R/W FF FF PHY_NOISE_CTRL2 15:8 Noise Attack Sets the attack characteristics of the NOISE algorithm. High nibble sets number of noise events needed to raise the NOISE level immediately, while the low nibble is the number of noise events needed to raise the level at the end of an 870 ms period. 7:0 Reserved Reads will produce undefined results R HPR25: HomePNA PHY Noise Statistics (Register 25) Table 57. Bits Mnemonic HPR25: HomePNA PHY Noise Statistics (Register 25) Description PHY_NOISE_STAT 15:8 Noise Level This is the digital value of the SLICE_LVL_NOISE output. It is effectively a measure of the noise level on the wire and tracks noise by counting the number of false triggers of the NOISE comparator in an 800 ms window. When auto-adaptation is enabled (bit 5 of the PHY_Control Register is false), this register is updated with the current NOISE count every 50 ns. When adaptation is disabled, this register may be written to and is used to generate both the SLICE_LVL_NOISE and SLICE_LVL_DATA signals. 7:0 Peak Level This is a measurement of the peak level of the last valid (non-collision) AID received. Am79C978 185 HPR26: HomePNA PHY Event Status (Register 26) Table 58. Bits HPR26: HomePNA PHY Event Status (Register 26) Mnemonic Description Read/ Write Default Hex Soft Reset R 0 0 PHY_Event Status 15:10 Reserved 9 RxPCOM Indicates a valid RxPCOM. An access to the RxCOM MSB Register 21 will clear this bit. R 0 0 8 TxPCOM Indicates a valid TxPCOM. Any access to the TxCOM registers (Registers 18 and 19) will clear this bit. R 0 0 7:4 Reserved Reads will produce undefined results. R 3 Packet Received Status is cleared by writing a 0. R/W 0 0 2 Packet Transmitted Status is cleared by writing a 0. R/W 0 0 1 Remote Command Received R/W 0 0 0 Remote Command Sent R/W 0 0 Read/ Write Default Hex Soft Reset A valid remote command was received. Status is cleared by writing a 0. A remote command has been sent. Status is cleared by writing a 0. HPR27: HomePNA PHY Event Status (Register 27) The Event Status register reports the state of each event source. Any bit may be written and so facilitate software-stimulated event testing. Table 59. Bits HPR27: HomePNA PHY Event Status (Register 27) Mnemonic Description AID_CTRL 15:8 AID_INTERVAL This value defines the number of TCLKs (116.6 ns) separating AID symbols. R/W 14 14 7:0 AID_ISBI This value defines the number of TCLKs (116.6 ns) separating AID symbol 0. R/W 40 40 Read/ Write Default Hex Soft Reset HPR28: HomePNA PHY ISBI Control (Register 28) Table 60. HPR8: HomePNA PHY ISBI Control (Register 28) Bits Mnemonic Description ISBI_CTRL 15:8 ISBI_SLOW This value defines the number of TCLKs (116.6 ns) separating data pulses for Symbol 0 in low speed mode. R/W 2C 2C 7:0 ISBI_FAST This value defines the number of TCLKs (116.6 ns) separating data pulses for Symbol 0 in high speed mode. R/W 1C 1C 186 Am79C978 HPR29: HomePNA PHY TX Control (Register 29) Table 61. Bits HPR29: HomePNA PHY TX Control (Register 29) Mnemonic Description Read/ Write Default Hex Soft Reset R/W 04 04 TX_CTRL 15:8 TX_PULSE_WIDTH This value defines the duration of a transmit pulse in OSC cycles (16.7 ns). This will effectively determine the transmit spectrum of the PHY. 7:4 TX_PULSE_CYCLES_N This value defines the number of pulses that will be driven onto the HRTXRX_N pin. R/W 4 4 3:0 TX_PULSE_CYCLES_P This value defines the number of pulses that will be driven onto the HRTXRX_P pin. R/W 4 4 HPR30: 1 Mbps HomePNA PHY Drive Level Control Test Register (Register 30) Table 62. Bits 15:12 HPR30: HomePNA PHY Drive Level Control Test Register (Register 30) Mnemonic Description Read/ Write Default Hex R YX RES Reserved; Write = 0; Read = X 11:6 High Level Control Defines the drive level that will be utilized in the High Power mode. R/W 15 5:0 Low Level Control Defines the drive level that will be utilized in the Low Power mode. R/W 09 Soft Reset HPR31: 1 Mbps HomePNA PHY Analog Control Register (Register 31) Table 63. Bits Mnemonic HPR31: HomePNA PHY Analog Control Register (Register 31) Description 15:11 Level_Adjust Global output slope adjustment. These bits control the number of current sources enable for transmit. Each bit represents a single current source. Thus 10101 enables three current sources as does 11100. 10:8 Reserved Reserved; Write = 0 7 6:0 Force_Link_Valid Reserved 1 = Link Status bit will be held valid 0 = Normal operation Reserved; Write = 0 Read/ Write Default Hex Soft Reset R/W 18 18 R/W 0 0 R/W 0 0 R/W 0 0 Note: 1. Writes to these bits will cause undefined functionality. Am79C978 187 10BASE-T PHY Management Registers (TBRs) The Am79C978 home networking device supports the MII basic register set and extended register set. Both sets of registers are accessible through the PHY Management Interface. As specified in the IEEE standard, the basic register set consists of the Control Register (Register 0) and the Status Register (Register 1). The extended register set consists of Registers 2 to 31 (decimal). Table 64 lists all the 10BASE-T registers implemented in the device. All the reserved registers should not be written to, and reading them will return a zero value. Table 64. Am79C978 10BASE-T PHY Management Register Set Register Address (in Decimal) Register Name Basic/ Extended 0 PHY Control B 1 PHY Status B 2-3 PHY Identifier E 4 Auto-Negotiation Advertisement E 5 Auto-Negotiation Link Partner Ability E 6 Auto-Negotiation Expansion E 7 Auto-Negotiation Next Page E 8-15 Reserved E 16 Interrupt Enable and Status E 17 PHY Control/Status E 18 Reserved E 19 PHY Management Extension E 20-23 Reserved E 24 Summary Status E 25-31 Reserved E 188 Am79C978 TBR0: 10BASE-T PHY Control Register (Register 0) Table 65. TBR0: 10BASE-T PHY Control Register (Register 0) Reg Bits Read/Write (Note 1) Default Value Soft Reset R/W, SC 0 0 0 = asserts Loopback mode, 1 = deasserts Loopback mode R/W 0 0 Name Soft Reset (Note 2) Description When write: 1 = PHY software reset, 0 = normal operation. 0 15 0 14 0 13 Speed Selection (Note 3) 1 = 100 Mbps, 0 = 10 Mbps R/W 1 1 0 12 Auto-Negotiation Enable 1 = enable Auto-Negotiation, 0 = disable Auto-Negotiation R/W 1 1 0 11 Power Down 1 = power down, 0 = normal operation R/W 0 0 0 10 1 = electrically isolate PHY 0 = normal operation R/W 1 1 0 9 Restart AutoNegotiation 1 = restart Auto-Negotiation, 0 = normal operation R/W, SC 0 0 0 8 Duplex Mode (Note 3) 1 = Full-Duplex, 0 = Half-Duplex R/W 1 Retains previous value 0 7 Collision Test 1 = enable COL signal test, 0 = disable COL signal test R/W 0 0 0 6-0 Reserved Write as 0, ignore on read RO 0 0 Loopback Isolate (Note 4) When read: 1 = reset in process, 0 = reset done. Notes: 1. R/W = Read/Write, SC = Self Clearing, RO = Read only. 2. Soft Reset does not reset the PDX block. Refer to the Soft Reset Section for details. 3. Bits 8 and 13 have no effect if Auto-Negotiation is enabled (Bit 12 = 1). 4. If the ISOL pin of the chip and the Isolate bit in Register 0 is 1, this bit will be set. Am79C978 189 TBR1: 10BASE-T Status Register (Register 1) The Status Register identifies the physical and Autonegotiation capabilities of the local PHY. This register is read only; a write will have no effect. Table 66. TBR1: 10BASE-T PHY Status Register (Register 1) Bits Name Description Default Value 15 100BASE-T4 1 = 100BASE-T4 able, 0 = not 100BASE-T4 able RO 0 14 100BASE-X Full-Duplex 1 = 100BASE-X full-duplex able, 0 = not 100BASE-X full-duplex able RO 0 13 100BASE-X Half-Duplex 1 = 100BASE-X half-duplex able, 0 = not 100BASE-X half-duplex able RO 0 12 10 Mbps Full-Duplex 1 = 10 Mbps full-duplex able, 0 = not 10 Mbps full-duplex able RO 1 11 10 Mbps Half-Duplex 1 = 10 Mbps half-duplex able, 0 = not 10 Mbps half-duplex able RO 1 Reserved Ignore when read RO NA 6 MF Preamble Suppression 1 = PHY can accept management (mgmt) frames with or without preamble, 0 = PHY can only accept mgmt frames with preamble RO 1 5 Auto-Negotiation Complete 1 = Auto-Negotiation completed, 0 = Auto-Negotiation not completed RO 0 4 Remote Fault 1 = remote fault detected, 0 = no remote fault detected RO, LH 0 3 Auto-Negotiation Ability 1 = PHY able to auto-negotiate, 0 = PHY not able to auto-negotiate RO 1 2 Link Status 1 = link is up, 0 = link is down RO, LL 0 1 Jabber Detect 1 = jabber condition detected, 0 = no jabber condition detected RO 0 0 Extended Capability 1 = extended register capabilities, 0 = basic register set capabilities only RO 1 10-7 Note: 1. LH = Latching High, LL = Latching Low. 190 Read/Write (Note 1) Am79C978 TBR2 and TBR3: 10BASE-T PHY Identifier (Registers 2 and 3) Registers 2 and 3 contain a unique PHY identifier, consisting of 22 bits of the organizationally unique IEEE Identifier, a 6-bit manufacturer's model number, and a 4-bit manufacturer's revision number. The most significant bit of the PHY identifier is bit 15 of register 2; the least significant bit of the PHY identifier is bit 0 of reg- Table 67. Bits 15-0 Name PHY_ID[31-16] Name TBR2: 10BASE-T PHY Identifier (Register 2) Read/ Write Description IEEE Address (bits 3-18); Register 2, bit 15 is MS bit of PHY Identifier Table 68. Bits ister 3. Register 2, bit 15 corresponds to bit 3 of the IEEE Identifier and register 2, bit 0 corresponds to bit 18 of the IEEE Identifier. Register 3, bit 15 corresponds to bit 19 of the IEEE Identifier and register 3, bit 10 corresponds to bit 24 of the IEEE Identifier. Register 3, bits 9-4 contain the manufacturer's model number and bits 3-0 contain the manufacturer's revision number. These registers are shown in Table 67 and Table 68. RO Default Value 0000000000000000 (0000 Hex) Soft Reset Retains original Value TBR3: 10BASE-T PHY Identifier (Register 3) Description Read/Write 15-10 PHY_ID[15-10] IEEE Address (bits 1924) RO 9-4 PHY_ID[9-4] Manufacturer's Model Number (bits 5-0) RO 3-0 PHY_ID[3-0] Revision Number (bits 3-0); Register 3, bit 0 is LS bit of PHY Identifier RO Am79C978 Default Value 011010 (1A Hex) 110111 (37 Hex) 0000 Soft Reset Retains original value Retains original value Retains original value 191 TBR4: 10BASE-T Auto-Negotiation Advertisement Register (Register 4) this register is to advertise the technology ability to the link partner device. See Table 69. This register contains the advertised ability of the Am79C978 home networking device. The purpose of When this register is modified, Restart AutoNegotiation (Register 0, bit 9) must be enabled to guarantee the change is implemented. Table 69. TBR4: 10BASE-T Auto-Negotiation Advertisement Register (Register 4) Bit(s) Name Description 15 Next Page When set, the device wishes to engage in next page exchange. If clear, the device does not wish to engage in next page exchange. 14 Reserved When set, a remote fault bit is inserted into the base link code word during the Auto Negotiation process. When cleared, the base link code work will have the bit position for remote fault as cleared. Read/ Write H/W or Soft Reset R/W 0 RO 0 R/W 0 RO 0 R/W 0 RO 0 13 Remote Fault 12:11 Reserved 10 PAUSE 9 Reserved 8 Full-Duplex 100BASE-TX This bit advertises Full-Duplex capability. When set, Full-Duplex capability is advertised. When cleared, Full-Duplex capability is not advertised. R/W 0 7 Half-Duplex 100BASE-TX This bit advertises Half-Duplex capability for the Auto-negotiation process. Setting this bit advertises Half-Duplex capability. Clearing this bit does not advertise Half-Duplex capability. R/W 0 6 Full-Duplex 10BASE-T This bit advertises Full-Duplex capability. When set, Full-Duplex capability is advertised. When cleared, Full-Duplex capability is not advertised. R/W 1 5 Half-Duplex 10BASE-T This bit advertises Half-Duplex capability for the Auto-negotiation process. Setting this bit advertises Half-Duplex capability. Clearing this bit does not advertise Half-Duplex capability. R/W 1 4:0 Selector Field The Am79C978 home networking device is an 802.3 compliant device RO 0x01 192 This bit should be set if the PAUSE capability is to be advertised. Am79C978 TBR5: 10BASE-T Auto-Negotiation Link Partner Ability Register (Register 5) The Auto-Negotiation Link Partner Ability Register is Read Only. The register contains the advertised ability of the link partner. The bit definitions represent the received link code word. This register contains either the base page or the link partner's next pages. See Table 70 and Table 71. Table 70. TBR5: 10BASE-T Auto-Negotiation Link Partner Ability Register (Register 5) - Base Page Format Read/ Write H/W or Soft Reset Link partner next page request RO 0 Acknowledge Link partner acknowledgment RO 0 Remote Fault Link partner remote fault request RO 0 RO 0 RO 0 Bit(s) Name 15 Next Page 14 13 12:5 Description Technology Ability Link partner technology ability field 4:0 Table 71. Selector Field Link partner selector field TBR5: 10BASE-T Auto-Negotiation Link Partner Ability Register (Register 5) - Next Page Format Bit(s) Name 15 Next Page 14 Acknowledge 13 Message Page 12 Acknowledge 2 11 Toggle 10:0 Message Field Read/ Write H/W or Soft Reset Link partner next page request RO 0 Link partner acknowledgment RO 0 Link partner message page request RO 0 RO 0 Link partner toggle bit RO 0 Link partner's message code RO 0 Description 1 = Link partner can comply with the request 0 = Link partner cannot comply with the request Am79C978 193 TBR6: 10BASE-T Auto-Negotiation Expansion Register (Register 6) process. The Auto-Negotiation Expansion Register bits are Read Only. See Table 72. The Auto-Negotiation Expansion Register provides additional information which aids the Auto-Negotiation Table 72. Bit(s) Name 15:5 Reserved TBR6: 10BASE-T Auto-Negotiation Expansion Register (Register 6) Description 4 Parallel Detection 1=Parallel detection fault Fault 0=No parallel detection fault 3 Link Partner Next Page Able 2 Next Page Able 1 Page Received 0 1 = Link partner is next page able 0 = Link partner is not next page able 1 = Am79C978 home networking device channel is next page able 0 = Am79C978 home networking device channel is not next page able 1 = A new page has been received Read/ Write H/W or Soft Reset RO 0 RO, LH 0 RO 0 RO 1 RO, LH 0 = A new page has not been received Link Partner ANEG 1 = Link partner is Auto-Negotiation able Able 0 = Link partner is not Auto-Negotiation able TBR7: 10BASE-T Auto-Negotiation Next Page Register (Register 7) RO 0 0 up the default value of 2001h represents a message page with the message code set to null. See Table 73. The Auto-Negotiation Next Page Register contains the next page link code word to be transmitted. On power- Table 73. TBR7: 10BASE-T Auto-Negotiation Next Page Register (Register 7) Bit(s) Name Description Read/ Write H/W or Soft Reset 15 Next Page Am79C978 home networking device channel next page request R/W 0 14 Reserved RO 0 13 Message Page R/W 1 R/W 0 Am79C978 home networking device channel toggle bit RO 0 Message code field R/W 0x001 12 Acknowledge 2 11 Toggle 10:0 Message Field Am79C978 home networking device channel message page request 1 = Am79C978 home networking device channel can comply with the request 0 = Am79C978 home networking device channel cannot comply with the request Reserved Registers (Registers 8-15, 18, 20-23, and 25-31) 31. These registers should be ignored when read and should not be written at any time. The Am79C978 home networking device contains reserved registers at addresses 8-15, 18, 20-23, and 25- 194 Am79C978 TBR16: 10BASE-T INTERRUPT Status and Enable Register (Register 16) and interrupt enable bits. The status is always updated whether or not the interrupt enable bits are set. When an interrupt occurs, the system will need to read the interrupt register to clear the status bits and determine the course of action needed. See Table 74. The Interrupt bits indicate when there is a change in the Link Status, Duplex Mode, Auto-Negotiation status, or Speed status. Register 16 contains the interrupt status Table 74. TBR16: 10BASE-T INTERRUPT Status and Enable Register (Register 16) Bit(s) Name 15:14 Reserved 13 Interrupt Test Enable (Note 1) Description 1 = When this bit is set, setting bits 12:9 of this register will cause a condition that will set bits 4:1 accordingly. The effect is to test the register bits with a forced interrupt condition. Read/ Write H/W or Soft Reset RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 RO 0 0 = Bits 4:1 are only set if the interrupt condition (if any bits in 12:9 are set) occurs. Link Status Change 12 Enable Duplex Mode Change 11 Enable Auto-Neg Change 10 Enable Speed Change 9 1 = Link Status Change enable 0 = This interrupt is masked 1 = Duplex Mode Change enable 0 = This interrupt is masked 1 = Auto-Negotiation Change enable 0 = This interrupt is masked 1 = Speed Change enable Enable 0 = This interrupt is masked Global 1= Global Interrupt enable 8 Enable 0 = This interrupt is masked 7:5 Reserved 4 Link Status Change 3 Duplex Mode Change 2 Auto-Negotiation Change 1 Speed Change 0 Global 1 = Link Status has changed on a port RO, 0 = No change in Link Status LH 1 = Duplex Mode has changed on a port RO, 0 = No change in Duplex mode LH 1 = Auto-Neg status has changed on a port RO, 0 = No change in Auto-Neg status LH 1 = Speed status has changed on a port RO, 0 = No change LH 1 = Indicates a change in status of any of the above interrupts RO, 0 = Indicates no change in Interrupt Status LH 0 0 0 0 0 Note: 1. All bits, except bit 13, are cleared on read (COR). The register must be read twice to see if it has been cleared. Am79C978 195 TBR17: 10BASE-T PHY Control/Status Register (Register 17) This register is used to control the configuration of the 10 Mbps PHY unit of the Am79C978 home networking device. See Table 75. Table 75. TBR17: 10BASE-T PHY Control/Status Register (Register 17) Read/Write H/W Reset Reserved R/W 0 Retains Previous Value 14 Reserved R/W 0 Retains Previous Value 13 Force Link Good Enable 1 = link status forced to link up state 0 = link status is determined by the device R/W 0 0 12 Disable Link Pulse 1 = Link pulses sent from the 10BASE-T transmitter are suppressed R/W 0 0 1 = Disables the SQE heartbeat which occurs after each 10BASE-T transmission 0 = The heart beat assertion occurs on the COL pin approximately 1 s after transmission and for a duration of 1 s. R/W 0 0 R/W 0 0 R/W 0 0 R/W 00 00 RO 0 0 R/W 0 0 1 = 10BASE-T receive squelch thresholds are reduced to allow reception of frames which are greater than 100 meters 0 = Squelch thresholds are set for standard distance of 100 meters R/W 0 0 1 = TX outputs not active for 10BASE-T. TX outputs to logical "0" for PECL. 0 = Transmit valid data R/W 0 0 1 = CRS is asserted when transmit or receive medium is active 0 = CRS is asserted when receive medium is active RO 0 0 RO 0 0 RO 0/1 0/1 Bits Name 15 11 SQE_TEST Disable 10 Reserved 9 Jabber Detect Disable 8:7 Reserved 6 Receive Polarity Reversed 5 4 3 Description 1 = disable jabber detect 0 = enable jabber detect 1 = Receive polarity of the 10BASE-T receiver is reversed 0 = Receive polarity is correct 1 = polarity correction circuit is disabled for Auto Receive Polarity 10BASE-T Correction Disable 0 = Self correcting polarity circuit is enabled Extended Distance Enable TX_DISABLE 2 TX_CRS_EN 1 Reserved 0 PHY Isolated 1 = Internal PHY is isolated 0 = Internal PHY is enabled Note: 1. For these loopback paths, the data is also transmitted out of the MDI pins (TX). 196 Am79C978 Soft Reset TBR19: 10BASE-T PHY Management Extension Register (Register 19) Table 76 contains the PHY Management Extension Register (Register 19) bits. Table 76. TBR19: 10BASE-T PHY Management Extension Register (Register 19) Bits Name 15:6 Reserved 5 4-0 Description Write as 0; ignore on read 1 = last management frame was Mgmt Frame Format invalid (opcode error, etc.) 0 = last management frame was valid PHY Address PHY Address defaults to 11110 Read/Write Default Value Soft Reset RO 0 0 RO 0 0 RO 11110 Retains Previous Value Reserved Register: 10BASE-T Configuration Register (Register 22) TBR24: 10BASE-T Summary Status Register (Register 24) This register is reserved. The Summary Status register is a global register containing status information. This register is Read/Only and represents the most important data which a single register access can convey. The Summary Status register indicates the following: Link Status, Full-Duplex Status, Auto-Negotiation Alert, and Speed. See Table 77. Reserved Register: 10BASE-T Carrier Status Register (Register 23) This register is reserved. Table 77. Bit(s) Name 15-4 Reserved 3 Link Status 2 Full-Duplex 1 0 AutoNEG Alert Speed TBR24: 10BASE-T Summary Status Register (Register 24) Description Write as 0; Ignore on Read 1 = Link Status is up 0 = Link Status is down Operating in Full-Duplex mode Operating in Half-Duplex mode 1 = AutoNEG status has changed 0 = AutoNEG status unchanged 1 = Operating at 100 Mbps 0 = Operating at 10 Mbps Am79C978 Read/ Write H/W or Soft Reset 0 0 R/O 0 R/O 0 R/O 0 R/O 0 197 Initialization Block Note: When SSIZE32 (BCR20, bit 8) is set to 0, the software structures are defined to be 16 bits wide. The base address of the initialization block must be aligned to a DWord boundary, i.e., CSR1, bit 1 and 0 must be cleared to 0. When SSIZE32 is set to 0, the initialization block looks like Table 78. Note: The Am79C978 controller performs DWord accesses to read the initialization block. This statement is Table 78. Address Bits 15-13 always true, regardless of the setting of the SSIZE32 bit. When SSIZE32 (BCR20, bit 8) is set to 1, the software structures are defined to be 32 bits wide. The base address of the initialization block must be aligned to a DWord boundary, i.e., CSR1, bits 1 and 0 must be cleared to 0. When SSIZE32 is set to 1, the initialization block looks like Table 79. Initialization Block (SSIZE32 = 0) Bit 12 Bits 11-8 IADR+00h MODE 15-00 IADR+02h PADR 15-00 IADR+04h PADR 31-16 IADR+06h PADR 47-32 IADR+08h LADRF 15-00 IADR+0Ah LADRF 31-16 IADR+0Ch LADRF 47-32 IADR+0Eh LADRF 63-48 IADR+10h RDRA 15-00 IADR+12h RLEN 0 TLEN 0 Bits 7-4 RES IADR+14h Bits 3-0 TDRA 23-16 TDRA 15-00 IADR+16h RES TDRA 23-16 Table 79. Initialization Block (SSIZE32 = 1) Address Bits 31-28 Bits 27-24 Bits 23-20 Bits 19-16 IADR+00h TLEN RES RLEN RES IADR+04h IADR+08h Bits 15-12 Bits 7-4 Bits 3-0 MODE PADR 31-00 RES PADR 47-32 IADR+0Ch LADRF 31-00 IADR+10h LADRF 63-32 IADR+14h RDRA 31-00 IADR+18h TDRA 31-00 RLEN and TLEN When SSIZE32 (BCR20, bit 8) is set to 0, the software structures are defined to be 16 bits wide, and the RLEN and TLEN fields in the initialization block are each three bits wide. The values in these fields determine the number of transmit and receive Descriptor Ring Entries (DRE) which are used in the descriptor rings. Their meaning is shown in Table 80. If a value other than those 198 Bits 11-8 listed in Table 80 is desired, CSR76 and CSR78 can be written after initialization is complete. When SSIZE32 (BCR20, bit 8) is set to 1, the software structures are defined to be 32 bits wide, and the RLEN and TLEN fields in the initialization block are each 4 bits wide. The values in these fields determine the number of transmit and receive Descriptor Ring Entries (DRE) which are used in the descriptor rings. Their meaning is shown in Table 81. Am79C978 If a value other than those listed in Table 80 is desired, CSR76 and CSR78 can be written after initialization is complete. Table 80. R/TLEN Decoding (SSIZE32 = 0) R/TLEN 000 001 010 011 100 101 110 111 Number of DREs 1 2 4 8 16 32 64 128 A logical address is passed through the CRC generator, producing a 32-bit result. The high order 6 bits of the CRC is used to select one of the 64 bit positions in the Logical Address Filter. If the selected filter bit is set, the address is accepted and the frame is placed into memory. The Logical Address Filter is used in multicast addressing schemes. The acceptance of the incoming frame based on the filter value indicates that the message may be intended for the node. It is the node's responsibility to determine if the message is actually intended for the node by comparing the destination address of the stored message with a list of acceptable logical addresses. RDRA and TDRA RDRA and TDRA indicate where the transmit and receive descriptor rings begin. Each DRE must be located at a 16-byte address boundary when SSIZE32 is set to 1 (BCR20, bit 8). Each DRE must be located at an 8byte address boundary when SSIZE32 is set to 0 (BCR20, bit 8). If the Logical Address Filter is loaded with all zeros and promiscuous mode is disabled, all incoming logical addresses except broadcast will be rejected. If the DRCVBC bit (CSR15, bit 14) is set as well, the broadcast packets will be rejected. See Figure 51. PADR This 48-bit value represents the unique node address assigned by the ISO 8802-3 (IEEE/ANSI 802.3) and used for internal address comparison. PADR[0] is compared with the first bit in the destination address of the incoming frame. It must be 0 since only the destination address of a unicast frames is compared to PADR. The six hex-digit nomenclature used by the ISO 8802-3 (IEEE/ANSI 802.3) maps to the Am79C978 home networking PADR register as follows: the first byte is compared with PADR[7:0] with PADR[0] being the least significant bit of the byte. The second ISO 8802-3 (IEEE/ANSI 802.3) byte is compared with PADR[15:8], again from the least significant bit to the most significant bit, and so on. The sixth byte is compared with PADR[47:40], the least significant bit being PADR[40]. Table 81. R/TLEN Decoding (SSIZE32 = 1) R/TLEN 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 11XX 1X1X against the physical address that was loaded through the initialization block. Number of DREs 1 2 4 8 16 32 64 128 256 512 512 512 Mode LADRF The Logical Address Filter (LADRF) is a 64-bit mask that is used to accept incoming Logical Addresses. If the first bit in the incoming address (as transmitted on the wire) is a 1, it indicates a logical address. If the first bit is a 0, it is a physical address and is compared The mode register field of the initialization block is copied into CSR15 and interpreted according to the description of CSR15. Am79C978 199 32-Bit Resultant CRC Received Message Destination Address 47 1 0 1 31 26 0 CRC GEN 63 SEL Logical Address Filter (LADRF) 0 64 MUX Match = 1 Packet Accepted Match = 0 Packet Rejected Match 6 22206B-54 Figure 51. Address Match Logic Receive Descriptors receive descriptors look like Table 83 (CRDA = Current Receive Descriptor Address). When SWSTYLE (BCR20, bits 7-0) is set to 0, then the software structures are defined to be 16 bits wide, and receive descriptors look like Table 82 (CRDA = Current Receive Descriptor Address). When SWSTYLE (BCR 20, bits 7-0) is set to 3, then the software structures are defined to be 32 bits wide, and receive descriptors look like Table 84 (CRDA = Current Receive Descriptor Address). When SWSTYLE (BCR 20, bits 7-0) is set to 2, then the software structures are defined to be 32 bits wide, and Table 82. Receive Descriptor (SWSTYLE = 0) Address CRDA+00h CRDA+02h CRDA+04h CRDA+06h Address CRDA+00h 31 15 14 13 12 OWN 1 0 ERR 1 0 FRAM 1 0 OFLO 1 0 30 29 CRDA+04h OWN ERR FRA M STP 8 28 26 27 OFL BUF CRC O F 25 24 23 22 RBADR[31:0] STP ENP BPE PAM 7-0 ENP BCNT MCNT Receive Descriptor (SWSTYLE = 2) RBADR[23:16] 21 20 19-16 15-12 11-0 LAFM BAM RES 1111 BCNT 0000 MCNT RFRTAG[14:0] USER SPACE Table 84. 200 9 Table 83. CRDA+08h RES CRDA+0Ch Address CRDA+00h CRDA+04h CRDA+08h CRDA+0Ch 11 10 RBADR[15:0] CRC BUFF 31 30 29 OWN ERR FRAM 28 Receive Descriptor (SWSTYLE = 3) 27 RES OFLO CRC 26 25 24 BUFF STP ENP RBADR[31:0] USER SPACE Am79C978 23 RES BPE 22-16 RES RES 15-12 0000 1111 11-0 MCNT BCNT RMD0 Bit 31-0 Name RBADR on the incoming frame. CRC is valid only when ENP is set and OFLO is not. CRC is set by the Am79C978 controller and cleared by the host. CRC will also be set when Am79C978 home networking receives an RX_ER indication from the external PHY through the MII. Description Receive Buffer address. This field contains the address of the receive buffer that is associated with this descriptor. RMD1 Bit 31 Name OWN Description 26 BUFF This bit indicates whether the descriptor entry is owned by the host (OWN = 0) or by the Am79C978 controller (OWN = 1). The Am79C978 controller clears the OWN bit after filling the buffer that the descriptor points to. The host sets the OWN bit after emptying the buffer. 1. The OWN bit of the next buffer is 0. 2. FIFO overflow occurred before the Am79C978 controller was able to read the OWN bit of the next descriptor. Once the Am79C978 controller or host has relinquished ownership of a buffer, it must not change any field in the descriptor entry. 30 ERR ERR is the OR of FRAM, OFLO, CRC, BUFF, or BPE. ERR is set by the Am79C978 controller and cleared by the host. 29 FRAM Framing error indicates that the incoming frame contains a noninteger multiple of eight bits and there was an FCS error. If there was no FCS error on the incoming frame, then FRAM will not be set even if there was a noninteger multiple of eight bits in the frame. FRAM is not valid in internal loopback mode. FRAM is valid only when ENP is set and OFLO is not. FRAM is set by the Am79C978 controller and cleared by the host. 28 27 OFLO CRC Overflow error indicates that the receiver has lost all or part of the incoming frame, due to an inability to move data from the receive FIFO into a memory buffer before the internal FIFO overflowed. OFLO is set by the Am79C978 controller and cleared by the host. Buffer error is set any time the Am79C978 controller does not own the next buffer while data chaining a received frame. This can occur in either of two ways: If a Buffer Error occurs, an Overflow Error may also occur internally in the FIFO, but will not be reported in the descriptor status entry unless both BUFF and OFLO errors occur at the same time. BUFF is set by the Am79C978 controller and cleared by the host. 25 STP Start of Packet indicates that this is the first buffer used by the Am79C978 controller for this frame. If STP and ENP are both set to 1, the frame fits into a single buffer. Otherwise, the frame is spread over more than one buffer. When LAPPEN (CSR3, bit 5) is cleared to 0, STP is set by the Am79C978 controller and cleared by the host. When LAPPEN is set to 1, STP must be set by the host. 24 ENP End of Packet indicates that this is the last buffer used by the Am79C978 controller for this frame. It is used for data chaining buffers. If both STP and ENP are set, the frame fits into one buffer and there is no data chaining. ENP is set by the Am79C978 controller and cleared by the host. CRC indicates that the receiver has detected a CRC (FCS) error Am79C978 201 23 BPE Bus Parity Error is set by the Am79C978 controller when a parity error occurred on the bus interface during data transfers to a receive buffer. BPE is valid only when ENP, OFLO, or BUFF are set. The Am79C978 controller will only set BPE when the advanced parity error handling is enabled by setting APERREN (BCR20, bit 10) to 1. BPE is set by the Am79C978 controller and cleared by the host. that a Broadcast frame would pass the hash filter, LAFM will be set on the reception of a Broadcast frame. This bit does not exist when the Am79C978 controller is programmed to use 16-bit software structures for the descriptor ring entries (BCR20, bits 7-0, SWSTYLE is cleared to 0). 20 BAM This bit does not exist when the Am79C978 controller is programmed to use 16-bit software structures for the descriptor ring entries (BCR20, bits 7-0, SWSTYLE is cleared to 0). 22 PAM Physical Address Match is set by the Am79C978 controller when it accepts the received frame due to a match of the frame's destination address with the content of the physical address register. PAM is valid only when ENP is set. PAM is set by the Am79C978 controller and cleared by the host. This bit does not exist when the Am79C978 controller is programmed to use 16-bit software structures for the descriptor ring entries (BCR20, bits 7-0, SWSTYLE is cleared to 0). 21 LAFM Logical Address Filter Match is set by the Am79C978 controller when it accepts the received frame based on the value in the logical address filter register. LAFM is valid only when ENP is set. LAFM is set by the Am79C978 controller and cleared by the host. Note that if DRCVBC (CSR15, bit 14) is cleared to 0, only BAM, but not LAFM will be set when a Broadcast frame is received, even if the Logical Address Filter is programmed in such a way that a Broadcast frame would pass the hash filter. If DRCVBC is set to 1 and the Logical Address Filter is programmed in such a way 202 Broadcast Address Match is set by the Am79C978 controller when it accepts the received frame, because the frame's destination address is of the type 'Broadcast.' BAM is valid only when ENP is set. BAM is set by the Am79C978 controller and cleared by the host. This bit does not exist when the Am79C978 controller is programmed to use 16-bit software structures for the descriptor ring entries (BCR20, bits 7-0, SWSTYLE is cleared to 0). 19-16 RES Reserved locations. These locations should be read and written as zeros. 15-12 ONES These four bits must be written as ones. They are written by the host and unchanged by the Am79C978 controller. 11-0 Buffer Byte Count is the length of the buffer pointed to by this descriptor, expressed as the two's complement of the length of the buffer. This field is written by the host and unchanged by the Am79C978 controller. BCNT RMD2 Bit 31 Name ZERO 30-16 RFRTAG Am79C978 Description This field is reserved. The Am79C978 controller will write a zero to this location. Receive Frame Tag. Indicates the Receive Frame Tag applied from the EADI interface. This field is user defined and has a default value of all zeros. When RXFRTG (CSR7, bit 14) is set to 0, 15-12 ZEROS 11-0 MCNT RFRTAG will be read as all zeros. See the section on Receive Frame Tagging for details. RMD3 This field is reserved. The Am79C978 controller will write zeros to these locations. 31-0 Message Byte Count is the length in bytes of the received message, expressed as an unsigned binary integer. MCNT is valid only when ERR is clear and ENP is set. MCNT is written by the Am79C978 controller and cleared by the host. When SWSTYLE (BCR20, bits 7-0) is set to 0, the software structures are defined to be 16 bits wide, and transmit descriptors look like Table 85 (CXDA = Current Transmit Descriptor Address). Bit Name Description US User Space. Reserved for user defined space. Transmit Descriptors When SWSTYLE (BCR 20, bits 7-0) is set to 2, the software structures are defined to be 32 bits wide, and transmit descriptors look like Table 86 (CXDA = Current Transmit Descriptor Address). When SWSTYLE (BCR 20, bits 7-0) is set to 3, then the software structures are defined to be 32 bits wide, and transmit descriptors look like Table 87 (CXDA = Current Transmit Descriptor Address). Table 85. Transmit Descriptor (SWSTYLE = 0) Address CXDA+00h 15 14 CXDA+02h OWN ERR CXDA+04h 1 1 CXDA+06h BUFF UFLO 13 12 ADD_ FCS 1 EX DEF MORE/ LTINT 1 Table 86. Address CXDA+00h 31 30 CXDA+04h OWN ERR CXDA+08h BUFF UFLO 11 10 TBADR[15:0] ONE 8 7-0 STP ENP TBADR[23:16] BCNT LCOL LCAR RTRY TDR Transmit Descriptor (SWSTYLE = 2) 29 28 27 26 ADD_ FCS EX DEF MORE/ LTINT ONE DEF STP LCOL LCAR RTRY RES CXDA+0Ch 25 24 TBADR[31:0] 23 22-16 15-12 11-4 3-0 ENP BPE RES 1111 RES RES RES RES RES TRC 22-16 15-12 11-4 3-0 RES TRC BCNT USER SPACE Table 87. Address 31 30 CXDA+00h BUFF UFLO CXDA+04h OWN ERR CXDA+08h CXDA+0Ch DEF 9 29 EX DEF ADD_ FCS Transmit Descriptor (SWSTYLE = 3) 28 27 26 25 LCOL LCAR RTRY MORE/ LTINT ONE DEF 24 23 RES STP ENP BPE RES 1111 BCNT TBADR[31:0] USER SPACE Am79C978 203 TMD0 Bit Name 31-0 TBADR ler and is read by the host. When LTINTEN is cleared to 0 (CSR5, bit 14), the Am79C978 controller will never look at the contents of bit 28, write operations by the host have no effect. When LTINTEN is set to 1 bit 28 changes its function to LTINT on host write operations and on Am79C978 controller read operations. Description Transmit Buffer address. This field contains the address of the transmit buffer that is associated with this descriptor. TMD1 Bit 31 Name OWN Description 30 ERR ERR is the OR of UFLO, LCOL, LCAR, RTRY or BPE. ERR is set by the Am79C978 controller and cleared by the host. This bit is set in the current descriptor when the error occurs and, therefore, may be set in any descriptor of a chained buffer transmission. 29 ADD_FCS ADD_FCS dynamically controls the generation of FCS on a frame by frame basis. This bit should be set with the ENP bit. However, for backward compatibility, it is recommended that this bit be set for every descriptor of the intended frame. When ADD_FCS is set, the state of DXMTFCS is ignored and transmitter FCS generation is activated. When ADD_FCS is cleared to 0, FCS generation is controlled by DXMTFCS. When APAD_XMT (CSR4, bit 11) is set to 1, the setting of ADD_FCS has no effect. ADD_FCS is set by the host, and is not changed by the Am79C978 controller. This is a reserved bit in the C-LANCE (Am79C90) controller. 28 204 MORE MORE indicates that more than one retry was needed to transmit a frame. The value of MORE is written by the Am79C978 controller. This bit has meaning only if the ENP bit is set. LTINT LTINT is used to suppress interrupts after successful transmission on selected frames. When LTINT is cleared to 0 and ENP is set to 1, the Am79C978 controller will not set TINT (CSR0, bit 9) after a successful transmission. TINT will only be set when the last descriptor of a frame has both LTINT and ENP set to 1. When LTINT is cleared to 0, it will only cause the suppression of interrupts for successful transmission. TINT will always be set if the transmission has an error. The LTINTEN overrides the function of TOKINTD (CSR5, bit 15). 27 ONE ONE indicates that exactly one retry was needed to transmit a frame. ONE flag is not valid when LCOL is set. The value of the ONE bit is written by the Am79C978 controller. This bit has meaning only if the ENP bit is set. 26 DEF Deferred indicates that the Am79C978 controller had to defer while trying to transmit a frame. This condition occurs if the channel is busy when the Am79C978 controller is ready to transmit. DEF is set by the Am79C978 controller and cleared by the host. 25 STP Start of Packet indicates that this is the first buffer to be used by the Am79C978 controller for this frame. It is used for data chaining This bit indicates whether the descriptor entry is owned by the host (OWN = 0) or by the Am79C978 controller (OWN = 1). The host sets the OWN bit after filling the buffer pointed to by the descriptor entry. The Am79C978 controller clears the OWN bit after transmitting the contents of the buffer. Both the Am79C978 controller and the host must not alter a descriptor entry after it has relinquished ownership. MORE/LTINT Bit 28 always functions as MORE. The value of MORE is written by the Am79C978 control- Am79C978 buffers. The STP bit must be set in the first buffer of the frame, or the Am79C978 controller will skip over the descriptor and poll the next descriptor(s) until the OWN and STP bits are set. STP is set by the host and is not changed by the Am79C978 controller. 24 23 ENP BPE the Am79C978 controller. There are no minimum buffer size restrictions. TMD2 Bit 31 Name BUFF End of Packet. End of Packet indicates that this is the last buffer to be used by the Am79C978 controller for this frame. It is used for data chaining buffers. If both STP and ENP are set, the frame fits into one buffer and there is no data chaining. ENP is set by the host and is not changed by the Am79C978 controller. 2. FIFO underflow occurred before the Am79C978 controller obtained the STATUS byte (TMD1[31:24]) of the next descriptor. BUFF is set by the Am79C978 controller and cleared by the host. If a Buffer Error occurs, an Underflow Error will also occur. BUFF is set by the Am79C978 controller and cleared by the host. 30 UFLO This bit does not exist, when the Am79C978 controller is programmed to use 16-bit software structures for the descriptor ring entries (BCR20, bits 7-0, SWSTYLE is cleared to 0). Reserved locations. 15-12 ONES These four bits must be written as ones. This field is written by the host and unchanged by the Am79C978 controller. 11-00 BCNT Buffer Byte Count is the usable length of the buffer pointed to by this descriptor, expressed as the two's complement of the length of the buffer. This is the number of bytes from this buffer that will be transmitted by the Am79C978 controller. This field is written by the host and is not changed by Buffer error is set by the Am79C978 controller during transmission when the Am79C978 controller does not find the ENP flag in the current descriptor and does not own the next descriptor. This can occur in either of two ways: 1. The OWN bit of the next buffer is 0. Bus Parity Error is set by the Am79C978 controller when a parity error occurred on the bus interface during a data transfers from the transmit buffer associated with this descriptor. The Am79C978 controller will only set BPE when the advanced parity error handling is enabled by setting APERREN (BCR20, bit 10) to 1. BPE is set by the Am79C978 controller and cleared by the host. 22-16 RES Description Underflow error indicates that the transmitter has truncated a message because it could not read data from memory fast enough. UFLO indicates that the FIFO has emptied before the end of the frame was reached. When DXSUFLO (CSR3, bit 6) is cleared to 0, the transmitter is turned off when an UFLO error occurs (CSR0, TXON = 0). When DXSUFLO is set to 1, the Am79C978 controller gracefully recovers from an UFLO error. It scans the transmit descriptor ring until it finds the start of a new frame and starts a new transmission. UFLO is set by the Am79C978 controller and cleared by the host. 29 Am79C978 EXDEF Excessive Deferral. Indicates that the transmitter has experienced 205 Excessive Deferral on this transmit frame, where Excessive Deferral is defined in the ISO 8802-3 (IEEE/ANSI 802.3) standard. Excessive Deferral will also set the interrupt bit EXDINT (CSR5, bit 7). 28 27 LCOL LCAR Late Collision indicates that a collision has occurred after the first channel slot time has elapsed. The Am79C978 home networkingAm79C978 controller does not retry on late collisions. LCOL is set by the Am79C978 controller and cleared by the host. Loss of Carrier is set when the carrier is lost during an Am79C978 controller initiated transmission when operating in half-duplex mode. The Am79C978 controller does not retry upon loss of carrier. It will continue to transmit the whole frame until done. LCAR will not be set when the device is operating in full-duplex mode. LCAR is not valid in Internal Loopback Mode. LCAR is set by the Am79C978 controller and cleared by the host. 26 RTRY Retry error indicates that the transmitter has failed after 16 attempts to successfully transmit a message, due to repeated collisions on the medium. If DRTY is set to 1 in the MODE register, RTRY will set after one failed transmission attempt. RTRY is set by the Am79C978 controller and cleared by the host. 25-4 RES Reserved locations. 3-0 TRC Transmit Retry Count. Indicates the number of transmit retries of the associated packet. The maximum count is 15. However, if a RETRY error occurs, the count will roll over to 0. In this case only, the Transmit Retry Count value of 0 should be interpreted as meaning 16. TRC is written by the Am79C978 controller into the last transmit descriptor of a frame, or when an error terminates a frame. Valid only when OWN is cleared to 0. TMD3 Bit 31-0 LCAR will be set when the PHY is in Link Fail state during transmission. 206 Am79C978 Name US Description User Space. Reserved for user defined space. REGISTER SUMMARY PCI Configuration Registers Table 88. PCI Configuration Registers Offset Name Width in Bit Access Mode Default Value RO 1022h 00h PCI Vendor ID 16 02h PCI Device ID 16 RO 2001h 04h PCI Command 16 RW 0000h 06h PCI Status 16 RW 0290h 08h PCI Revision ID 8 RO 50h 09h PCI Programming IF 8 RO 00h 0Ah PCI Sub-Class 8 RO 00h 0Bh PCI Base-Class 8 RO 02h 0Ch Reserved 8 RO 00h 0Dh PCI Latency Timer 8 RW 00h 0Eh PCI Header Type 8 RO 00h 0Fh Reserved 8 RO 00h 10h PCI I/O Base Address 32 RW 0000 0001h 14h PCI Memory Mapped I/O Base Address 32 RW 0000 0000h Reserved 8 RO 00h 2Ch PCI Subsystem Vendor ID 16 RO 00h 2Eh PCI Subsystem ID 16 RO 00h 30h PCI Expansion ROM Base Address 32 RW 0000 0000h 34h Capabilities Pointer 8 RO 40h Reserved 8 RO 00h 3Ch PCI Interrupt Line 8 RW 00h 3Dh PCI Interrupt Pin 8 RO 01h 3Eh PCI MIN_GNT 8 RO 06h 3Fh PCI MAX_LAT 8 RO FFh 40h PCI Capability Identifier 8 RO 01h 41h PCI Next Item Pointer 8 RO 00h 42h PCI Power Management Capabilities 16 RO 00h 44h PCI Power Management Control/Status 16 RO 00h 46h PCI PMCSR Bridge Support Extensions 8 RO 00h 47h PCI Data 8 RO 00h 48h - FFh Reserved 8 RO 00h 18h - 2Bh 31h - 3Bh Note: RO = read only, RW = read/write Am79C978 207 Control and Status Registers Table 89. Control and Status Registers (CSRs) RAP Addr Symbol Default Value 00 CSR0 uuuu 0004 Am79C978 Controller Status Register R 01 CSR1 uuuu uuuu Lower IADR: maps to location 16 S 02 CSR2 uuuu uuuu Upper IADR: maps to location 17 S 03 CSR3 uuuu 0000 Interrupt Masks and Deferral Control S 04 CSR4 uuuu 0115 Test and Features Control R 05 CSR5 uuuu 0000 Extended Control and Interrupt 1 R 06 CSR6 uuuu uuuu RXTX: RX/TX Encoded Ring Lengths S 07 CSR7 0uuu 0000 Extended Control and Interrupt 1 R 08 CSR8 uuuu uuuu LADRF0: Logical Address Filter -- LADRF[15:0] S 09 CSR9 uuuu uuuu LADRF1: Logical Address Filter -- LADRF[31:16] S 10 CSR10 uuuu uuuu LADRF2: Logical Address Filter -- LADRF[47:32] S Comments Use 11 CSR11 uuuu uuuu LADRF3: Logical Address Filter -- LADRF[63:48] S 12 CSR12 uuuu uuuu PADR0: Physical Address Register -- PADR[15:0][ S 13 CSR13 uuuu uuuu PADR1: Physical Address Register -- PADR[31:16] S 14 CSR14 uuuu uuuu PADR2: Physical Address Register -- PADR[47:32] S 15 CSR15 see register description MODE: Mode Register S 16 CSR16 uuuu uuuu IADRL: Base Address of INIT Block Lower (Copy) T 17 CSR17 uuuu uuuu IADRH: Base Address of INIT Block Upper (Copy) T 18 CSR18 uuuu uuuu CRBAL: Current RCV Buffer Address Lower T 19 CSR22 uuuu uuuu CRBAU: Current RCV Buffer Address Upper T 20 CSR20 uuuu uuuu CXBAL: Current XMT Buffer Address Lower T 21 CSR21 uuuu uuuu CXBAU: Current XMT Buffer Address Upper T 22 CSR22 uuuu uuuu NRBAL: Next RCV Buffer Address Lower T 23 CSR23 uuuu uuuu NRBAU: Next RCV Buffer Address Upper T 24 CSR24 uuuu uuuu BADRL: Base Address of RCV Ring Lower S 25 CSR25 uuuu uuuu BADRU: Base Address of RCV Ring Upper S 26 CSR26 uuuu uuuu NRDAL: Next RCV Descriptor Address Lower T 27 CSR27 uuuu uuuu NRDAU: Next RCV Descriptor Address Upper T 28 CSR28 uuuu uuuu CRDAL: Current RCV Descriptor Address Lower T 29 CSR29 uuuu uuuu CRDAU: Current RCV Descriptor Address Upper T 30 CSR30 uuuu uuuu BADXL: Base Address of XMT Ring Lower S 31 CSR31 uuuu uuuu BADXU: Base Address of XMT Ring Upper S 32 CSR32 uuuu uuuu NXDAL: Next XMT Descriptor Address Lower T 33 CSR33 uuuu uuuu NXDAU: Next XMT Descriptor Address Upper T Note: u = undefined value, R = Running register, S = Setup register, T = Test register; all default values are in hexadecimal format. 208 Am79C978 Control and Status Registers (Continued) RAP Addr Symbol Default Value After H_RESET 34 CSR34 uuuu uuuu CXDAL: Current XMT Descriptor Address Lower T 35 CSR35 uuuu uuuu CXDAU: Current XMT Descriptor Address Upper T 36 CSR36 uuuu uuuu NNRDAL: Next Next Receive Descriptor Address Lower T 37 CSR37 uuuu uuuu NNRDAU: Next Next Receive Descriptor Address Upper T 38 CSR38 uuuu uuuu NNXDAL: Next Next Transmit Descriptor Address Lower T 39 CSR39 uuuu uuuu NNXDAU: Next Next Transmit Descriptor Address Upper T 40 CSR40 uuuu uuuu CRBC: Current Receive Byte Count T 41 CSR41 uuuu uuuu CRST: Current Receive Status T 42 CSR42 uuuu uuuu CXBC: Current Transmit Byte T 43 CSR43 uuuu uuuu CXST: Current Transmit Status T 44 CSR44 uuuu uuuu NRBC: Next RCV Byte Count T 45 CSR45 uuuu uuuu NRST: Next RCV Status T 46 CSR46 uuuu uuuu POLL: Poll Time Counter T 47 CSR47 uuuu uuuu PI: Polling Interval S 48 CSR48 uuuu uuuu Reserved 49 CSR49 uuuu uuuu Reserved 50 CSR50 uuuu uuuu Reserved 51 CSR51 uuuu uuuu Reserved 52 CSR52 uuuu uuuu Reserved 53 CSR53 uuuu uuuu Reserved 54 CSR54 uuuu uuuu Reserved 55 CSR55 uuuu uuuu Reserved 56 CSR56 uuuu uuuu Reserved 57 CSR57 uuuu uuuu Reserved 58 CSR58 see register description SWS: Software Style S 59 CSR59 uuuu uuuu Reserved T 60 CSR60 uuuu uuuu PXDAL: Previous XMT Descriptor Address Lower T 61 CSR61 uuuu uuuu PXDAU: Previous XMT Descriptor Address Upper T 62 CSR62 uuuu uuuu PXBC: Previous Transmit Byte Count T 63 CSR63 uuuu uuuu PXST: Previous Transmit Status T 64 CSR64 uuuu uuuu NXBAL: Next XMT Buffer Address Lower T 65 CSR65 uuuu uuuu NXBAU: Next XMT Buffer Address Upper T 66 CSR66 uuuu uuuu NXBC: Next Transmit Byte Count T 67 CSR67 uuuu uuuu NXST: Next Transmit Status T 68 CSR68 uuuu uuuu Reserved 69 CSR69 uuuu uuuu Reserved 70 CSR70 uuuu uuuu Reserved Comments Am79C978 Use 209 Control and Status Registers (Continued) RAP Addr Symbol Default Value After H_RESET 71 CSR71 uuuu uuuu Reserved 72 CSR72 uuuu uuuu RCVRC: RCV Ring Counter 73 CSR73 uuuu uuuu Reserved 74 CSR74 uuuu uuuu XMTRC: XMT Ring Counter 75 CSR75 uuuu uuuu Reserved 76 CSR76 uuuu uuuu RCVRL: RCV Ring Length 77 CSR77 uuuu uuuu Reserved 78 CSR78 uuuu uuuu XMTRL: XMT Ring Length 79 CSR79 uuuu uuuu Reserved 80 CSR80 uuuu 1410 DMATCFW: DMA Transfer Counter and FIFO Threshold 81 CSR81 uuuu uuuu Reserved 82 CSR82 uuuu uuuu Transmit Descriptor Pointer Address Lower 83 CSR83 uuuu uuuu Reserved 84 CSR84 uuuu uuuu DMABA: Address Register Lower T 85 CSR85 uuuu uuuu DMABA: Address Register Upper T 86 CSR86 uuuu uuuu DMABC: Buffer Byte Counter T 87 CSR87 uuuu uuuu Reserved 88 CSR88 262 5003 Chip ID Register Lower T 89 CSR89 uuuu 262 Chip ID Register Upper T 90 CSR90 uuuu uuuu Reserved 91 CSR91 uuuu uuuu Reserved T 92 CSR92 uuuu uuuu RCON: Ring Length Conversion T 93 CSR93 uuuu uuuu Reserved 94 CSR94 uuuu uuuu Reserved 95 CSR95 uuuu uuuu Reserved 96 CSR96 uuuu uuuu Reserved 97 CSR97 uuuu uuuu Reserved 98 CSR98 uuuu uuuu Reserved 99 CSR99 uuuu uuuu Reserved 100 CSR100 uuuu 0200 Bus Timeout 101 CSR101 uuuu uuuu Reserved 102 CSR102 uuuu uuuu Reserved 103 CSR103 uuuu 0105 Reserved 104 CSR104 uuuu uuuu Reserved 105 CSR105 uuuu uuuu Reserved 106 CSR106 uuuu uuuu Reserved 107 CSR107 uuuu uuuu Reserved 210 Comments Use T T S S S S S Am79C978 Control and Status Registers (Concluded) RAP Addr Symbol Default Value After H_RESET 108 CSR108 uuuu uuuu Reserved 109 CSR109 uuuu uuuu Reserved 110 CSR110 uuuu uuuu Reserved Comments 111 CSR111 uuuu uuuu Reserved 112 CSR112 uuuu uuuu Missed Frame Count 113 CSR113 uuuu uuuu Reserved 114 CSR114 uuuu uuuu Received Collision Count 115 CSR115 uuuu uuuu Reserved 116 CSR116 0000 0000 OnNow Miscellaneous 117 CSR117 uuuu uuuu Reserved 118 CSR118 uuuu uuuu Reserved Use R R S 119 CSR119 uuuu 0105 Reserved 120 CSR120 uuuu uuuu Reserved 121 CSR121 uuuu uuuu Reserved 122 CSR226 uuuu 0000 Receive Frame Alignment Control 123 CSR237 uuuu uuuu Reserved 124 CSR248 uuuu 0000 Test Register 1 T 125 CSR125 003c 0060 MAC Enhanced Configuration Control T 126 CSR126 uuuu uuuu Reserved 127 CSR127 uuuu uuuu Reserved Am79C978 S 211 Bus Configuration Registers Writes to those registers marked as "Reserved" will have no effect. Reads from these locations will produce undefined values. Table 90. Bus Configuration Registers (BCRs) 212 RAP 0 1 2 3 4 5 6 7 8 9 10-15 16 17 18 19 20 22 23 24 25 26 27 28 29 30 31 32 33 34 35 Mnemonic MSRDA MSWRA MC Reserved LED0 LED1 LED2 LED3 Reserved FDC Reserved IOBASEL IOBASEU BSBC EECAS SWS PCILAT PCISID PCISVID SRAMSIZ SRAMB SRAMIC EBADDRL EBADDRU EBDR STVAL MIICAS MIIADDR MIIMDR PCIVID Default 0005h 0005h 0002h N/A 00C0h 0084h 0088h 0090h N/A 0000h N/A N/A N/A 9001h 0002h 0200h FF06h 0000h 0000h 0000h 0000h 0000h N/A N/A N/A FFFFh 0000h N/A N/A 1022h 36 PMC_A C811h 37 38 39 40 41 42 43 44 45 46 47 48 49 DATA0 DATA1 DATA2 DATA3 DATA4 DATA5 DATA6 DATA7 PMR1 PMR2 PMR3 LED4 PHY_SEL 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h N/A N/A N/A 0082h 8000h Name Reserved Reserved Miscellaneous Configuration Reserved LED0 Status LED1 Status LED2 Status LED3 Status Reserved Full-Duplex Control Reserved Reserved Reserved Burst and Bus Control EEPROM Control and Status Software Style PCI Latency PCI Subsystem ID PCI Subsystem Vendor ID SRAM Size SRAM Boundary SRAM Interface Control Expansion Bus Address Lower Expansion Bus Address Upper Expansion Bus Data Port Software Timer Value PHY Control and Status PHY Address PHY Management Data PCI Vendor ID PCI Power Management Capabilities (PMC) Alias Register PCI DATA Register Zero Alias Register PCI DATA Register One Alias Register PCI DATA Register Two Alias Register PCI DATA Register Three Alias Register PCI DATA Register Four Alias Register PCI DATA Register Five Alias Register PCI DATA Register Six Alias Register PCI DATA Register Seven Alias Register Pattern Matching Register 1 Pattern Matching Register 2 Pattern Matching Register 3 LED4 Status PHY Select Am79C978 Programmability User EEPROM No No No No Yes Yes No No Yes Yes Yes Yes Yes Yes Yes Yes No No Yes Yes No No No No No No Yes Yes Yes No Yes No Yes Yes No Yes No Yes Yes Yes Yes Yes Yes Yes Yes No Yes No Yes No Yes No Yes Yes Yes Yes Yes No No Yes No Yes No No No No No No No No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No No Yes Yes 10BASE-T PHY Management Registers Writes to registers marked "Reserved" will be written as zeros. Reads from these locations will produce undefined values. Table 91. 10BASE-T PHY Management Registers (TBRs) Register Address 0 Symbol TBR0 PHY Control Register Default Value After H_RESET 2500h 1 TBR1 PHY Status Register 7849h 2 TBR2 PHY_ID[31:16] 0000h 3 TBR3 PHY_ID[15:0] 6BA0h 4 TBR4 Auto-Negotiation Advertisement Register 03C1h 5 TBR5 Auto-Negotiation Link Partner Ability Register 0000h 6 TBR6 Auto-Negotiation Expansion Register 0004h 7 TBR7 Auto-Negotiation Next Page Register 2001h 8-15 TBR8-TBR15 16 TBR16 Interrupt Status and Enable Register 0000h 17 TBR17 PHY Control/Status Register 0001h 18 TBR18 Reserved -- PHY Management Extension Register -- Reserved -- 19 TBR19 20-23 TBR20-TBR23 24 TBR24 25-31 TBR25-TBR31 Name Reserved -- Summary Status Register Reserved 0001h -- Am79C978 213 1 Mbps HomePNA PHY Management Registers Table 92. 1 Mbps HomePNA PHY Management Registers (HPRs) Register Address 0 Symbol HPR0 MII Control Register Default Value After H_RESET 0400h 1 HPR1 MII Status Register 0841h 2 HPR2 MII PHY_ID Register 0000h 3 HPR3 MII PHY_ID Register 6B90h 4 HPR4 Auto-Negotiation Register 0021h 5 HPR5 Auto-Negotiation Register 0000h 6 HPR6 Auto-Negotiation Register 0000h 7 HPR7 Auto-Negotiation Register 0000h 8-15 HPR8-HPR15 16 HPR16 PHY Control Register 17 HPR17 Status and Control 18 HPR18 PHY TXCOMM Register 0000h 19 HPR19 PHY TXCOMM Register 0000h 20 HPR20 PHY RXCOMM Register 0000h 21 HPR21 PHY RXCOMM Register 0000h 22 HPR22 PHY AID Register 0000h 23 HPR23 PHY Noise Control Register 04FFh 24 HPR24 PHY Noise Control 2 Register F4xxh 25 HPR25 PHY Noise Statistics Register 04D0h 26 HPR26 Event Status Register 0000h 27 HPR27 AID Control Register 1440h 28 HPR28 ISBI Control Register 2C1Ch 29 HPR29 TX Control Register 0444h 30 HPR30 Drive Level Control x549h 31 HPR31 Analog Control C000h 214 Name Reserved -0005h -- Am79C978 REGISTER PROGRAMMING SUMMARY Am79C978 Programmable Registers Table 93. Register CSR0 Control and Status Registers Contents Status and control bits: (DEFAULT = 0004) 8000 4000 2000 1000 ERR -CERR MISS 0800 0400 0200 0100I MERR RINT TINT IDON 0080 0040 INTR IENA 0020 0010 RXON TXON Lower IADR (Maps to CSR 16) Upper IADR (Maps to CSR 17) Interrupt masks and Deferral Control: (DEFAULT = 0) 8000 -0800 MERRM 0080 -4000 -0400 RINTM 0040 DXSUFLO 2000 -0200 TINTM 0020 LAPPEN 1000 MISSM 0100 IDONM 0010 DXMT2PD CSR4 Interrupt masks, configuration and status bits: (DEFAULT = 0115) 8000 -0800 APAD_XMT 0080 UNITCMD 4000 DMAPLUS 0400 ASTRP_RCV 0040 UNIT 2000 -0200 MFCO 0020 RCVCCO 1000 TXDPOLL 0100 MFCOM 0010 RCVCCOM CSR5 Extended Interrupt masks, configuration and status bits: (DEFAULT = 0XXX) 8000 TOKINTD 0800 SINT 0080 EXDINT 4000 LTINTEN 0400 SINTE 0040 EXDINTE 2000 -0200 -0020 MPPLBA 1000 -0100 -0010 MPINT CSR7 Extended Interrupt masks, configuration and status bits: (DEFAULT = 0000) 8000 FASTSPND 0800 STINT 0080 MAPINT 4000 RXFRMTG 0400 STINTE 0040 MAPINTE 2000 RDMD 0200 MREINT 0020 MCCINT 1000 RXDPOLL 0100 MREINTE 0010 MCCINTE CSR8 - CSR11 Logical Address Filter CSR12 - CSR14 Physical Address Register MODE: (DEFAULT = 0) 0008 0004 0002 TDMD STOP STRT 0001 INIT 0008 0004 0002 0001 EMBA BSWP --- 0008 0004 0002 0001 TXSTRT TXSTRTM --- 0008 0004 0002 0001 MPINTE MPEN MPMODE SPND 0008 0004 0002 0001 MCCIINT MCCIINTE MIIPDTINT MIIPDTNTE 0008 0004 0002 0001 DXMTFCS LOOP DTX DRX CSR1 CSR2 CSR3 CSR15 CSR47 CSR49 CSR58 bits [8:7] = PORTSEL, Port Selection 11 PHY Selected 10 Reserved 8000 PROM 0800 -4000 DRCVBC 0400 -2000 DRCVPA 0200 -1000 -0100 PORTSEL1 TXPOLLINT: Transmit Polling Interval RXPOLLINT: Receive Polling Interval Software Style (mapped to BCR20) 0080 0040 0020 0010 PORTSEL0 INTL DRTY FCOLL bits [7:0] = SWSTYLE, Software Style Register. 8000 4000 2000 1000 0000 LANCE/PCnet-ISA 0002 ----- PCnet-32 0800 0400 0200 0100 -APERREN -SSIZE32 Am79C978 0080 0040 0020 0010 ----- 0008 0004 0002 0001 SWSTYLE3 SWSTYLE2 -SWSTYLE0 215 Am79C978 Programmable Registers (Continued) Register CSR76 CSR78 CSR80 Contents RCVRL: RCV Descriptor Ring length XMTRL: XMT Descriptor Ring length FIFO threshold and DMA burst control (DEFAULT = 2810) 8000 Reserved 4000 Reserved bits [13:12] = RCVFW, Receive FIFO Watermark 0000 Request DMA when 16 bytes are present 1000 Request DMA when 64 bytes are present 2000 Request DMA when 112 bytes are present 3000 Reserved bits [11:10] = XMTSP, Transmit Start Point 0000 Start transmission after 20/36 (No SRAM/SRAM) bytes have been written 0400 Start transmission after 64 bytes have been written 0800 Start transmission after 128 bytes have been written 0C00 Start transmission after 220 max/Full Packet (No SRAM/SRAM with UFLO bit set) bytes have been written bits [9:8] = XMTFW, Transmit FIFO Watermark 0000 Start DMA when 16 write cycles can be made 0100 Start DMA when 32 write cycles can be made 0200 Start DMA when 64 write cycles can be made CSR88~89 CSR112 CSR114 CSR116 CSR122 CSR124 CSR125 0300 Start DMA when 128 write cycles can be made bits [7:0] = DMA Burst Register Chip ID (Contents = v12626003; v = Version Number) Missed Frame Count Receive Collision Count OnNow Miscellaneous 8000 -0800 -0080 PMAT 0008 RWU_DRIVER 4000 -- 0400 -- 0040 EMPPLBA 0004 RWU_GATE 2000 -- 0200 PME_EN_OVR 0020 MPMAT 0002 RWU_POL 1000 -0100 LCDET Receive Frame Alignment Control 8000 -0800 -- 0010 MPPEN 0001 RST_POL 0080 -- 0008 -- 4000 -- 0400 -- 0040 -- 0004 -- 2000 -- 0200 -- 0020 -- 0002 -- 1000 -0100 -BMU Test Register (DEFAULT = 0000) 8000 -0800 -- 0010 -- 0001 RCVALGN 0080 -- 0008 -- 4000 -- 0400 -- 0040 -- 0004 RPA 2000 -- 0200 -- 0020 -- 0002 -- 1000 -0100 -0010 MAC Enhanced Configuration Control (DEFAULT = 603c) -- 0001 -- bits [15:8] = IPG, InterPacket Gap (Default = 60xx, 96 bit times) bits [8:0] = IFS1, InterFrame Space Part 1 (Default = xx3c, 60 bit times) 216 Am79C978 Am79C978 Programmable Registers (Continued) Table 94. Bus Configuration Registers RAP Addr Register 0 MSRDA 1 MSWRA 2 MC 4 5 6 7 9 16 17 18 19 20 LED0 LED1 LED2 LED3 FDC IOBASEL IOBASEU BSBC EECAS Contents Programs width of DMA read signal (DEFAULT = 5) Programs width of DMA write signal (DEFAULT = 5) Miscellaneous Configuration bits: (DEFAULT = 2) 8000 -0800 -0080 4000 -- 0400 -- 0040 INITLEVEL 0008 0004 -- 2000 -- 0200 -- 0020 -- 1000 -0100 APROMWE 0010 -Programs the function and width of the LED0 signal. (DEFAULT = 00C0) 8000 LEDOUT 0800 -0080 PSE EADISEL -- 0002 -- ASEL 0001 0008 POWER 4000 LEDPOL 0400 -- 0040 LNKSE 0004 RCVE 2000 LEDDIS 0200 MPSE 0020 RCVME 0002 SPEED 1000 100E 0100 FDLSE 0010 XMTE Programs the function and width of the LED1 signal. (DEFAULT = 0084) 8000 LEDOUT 0800 -0080 PSE 0001 COLE 0008 POWER 4000 LEDPOL 0400 -- 0040 LNKSE 0004 RCVE 2000 LEDDIS 0200 MPSE 0020 RCVME 0002 SPEED 1000 100E 0100 FDLSE 0010 XMTE Programs the function and width of the LED2 signal. (DEFAULT = 0088) 8000 LEDOUT 0800 -0080 PSE 0001 COLE 0008 POWER 4000 LEDPOL 0400 -- 0040 LNKSE 0004 RCVE 2000 LEDDIS 0200 MPSE 0020 RCVME 0002 SPEED 1000 100E 0100 FDLSE 0010 XMTE Programs the function and width of the LED3 signal. (DEFAULT = 0090) 8000 LEDOUT 0800 -0080 PSE 0001 COLE 0008 POWER 4000 LEDPOL 0400 -- 0040 LNKSE 0004 RCVE 2000 LEDDIS 0200 MPSE 0020 RCVME 0002 SPEED 1000 100E 0100 FDLSE Full-Duplex Control. (DEFAULT= 0000) 8000 -0800 -- 0010 XMTE 0001 COLE 0080 -- 0008 -- 4000 -- 0400 -- 0040 -- 0004 FDRPAD 2000 -- 0200 -- 0020 -- 0002 -- 1000 -0100 -I/O Base Address Lower I/O Base Address Upper Burst Size and Bus Control (DEFAULT = 2101) 8000 ROMTMG3 0800 NOUFLO 0010 -- 0001 FDEN 0080 DWIO 0008 -- 4000 ROMTMG2 0400 -- 0040 BREADE 0004 -- 2000 ROMTMG1 0200 MEMCMD 0020 BWRITE 0002 -- -- 0001 -- 1000 ROMTMG0 0100 EXTREQ EEPROM Control and Status (DEFAULT = 0002) 8000 PVALID 0800 -- 0010 0080 -- 0008 4000 PREAD 0400 -- 0040 -- 0004 ECS 2000 EEDET 0200 -- 0020 -- 0002 ESK EEN 0001 EDI/EDO 1000 -0100 -0010 SWSTYLE Software Style (DEFAULT = 0000, maps to CSR 58) Am79C978 -- 217 Am79C978 Programmable Registers (Continued) RAP Addr 22 Register PCILAT Contents PCI Latency (DEFAULT = FF06) bits [15:8] = MAX_LAT bits [7:0] = MIN_GNT 25 SRAMSIZE SRAM Size (DEFAULT = 0000) bits [7:0] = SRAM_SIZE 26 SRAMBND SRAM Boundary (DEFAULT = 0000) bits [7:0] = SRAM_BND 27 SRAMIC SRAM Interface Control (Default = 0000) 8000PTR TST 4000LOLATRX bits [5:3] = EBCS, Expansion Bus Clock Source 0000 CLK pin, PCI clock 0008 Time Base Clock 0010 EBCLK pin, Expansion Bus Clock bits [2:0] = CLK_FAC, Expansion Bus Clock Factor 0000 1/1 clock factor 0001 1/2 clock factor 0002 -0003 -- 28 EPADDRL Expansion Port Address Lower (Default = 0000) 29 EPADDRU Expansion Port Address Upper (Default = 0000) 8000 4000 2000 1000 FLASH LAINC --- 0800 0400 0200 0100 ----- 0080 0040 0020 0010 30 EBDATA Expansion Bus Data Port 31 STVAL Software Timer Interrupt Value (DEFAULT = FFFF) 32 MIICAS PHY Status and Control (DEFAULT = 0000) 8000 4000 2000 1000 33 MIIADDR ANTST MIIPD FMDC1 FMDC0 0800 0400 0200 0100 APEP APDW2 APDW1 APDW0 0080 0040 0020 0010 ----- 0008 0004 0002 0001 EPADDRU3 EPADDRU2 EPADDRU1 EPADDRU0 DANAS XPHYRST XPHYANE XPHYFD 0008 0004 0002 0001 XPHYSP -MIILP -- PHY Address (DEFAULT = 0000) bits [9:5] = PHYAD, Physical Layer Device Address bits [4:0] = REGAD, Auto-Negotiation Register Address 218 34 MIIMDR 35 PCI Vendor ID PCI Vendor ID Register (DEFAULT = 1022h) PHY Data Port 36 PMC Alias PCI Power Management Capabilities (DEFAULT = 0000) 37 DATA 0 PCI Data Register Zero Alias Register (DEFAULT = 0000) 38 DATA 1 PCI Data Register One Alias Register (DEFAULT = 0000) 39 DATA 2 PCI Data Register Two Alias Register (DEFAULT = 0000) 40 DATA 3 PCI Data Register Three Alias Register (DEFAULT = 0000) 41 DATA 4 PCI Data Register Four Alias Register (DEFAULT = 0000) 42 DATA 5 PCI Data Register Five Alias Register (DEFAULT = 0000) 43 DATA 6 PCI Data Register Six Alias Register (DEFAULT = 0000) 44 DATA 7 PCI Data Register Seven Alias Register (DEFAULT = 0000) 45 PMR 1 OnNow Pattern Matching Register 1 46 PMR 2 OnNow Pattern Matching Register 2 47 PMR 3 OnNow Pattern Matching Register 3 Am79C978 Am79C978 Programmable Registers (Concluded) RAP Addr 48 49 Register LED4 PHY_SEL Contents Programs the function and width of the LED3 signal. (DEFAULT = 0082) 8000 LEDOUT 0800 -- 0080 PSE 0008 4000 LEDPOL 2000 LEDDIS 1000 100E POWER 0400 -- 0040 LNKSE 0004 RCVE 0200 MPSE 0020 RCVME 0002 SPEED 0100 FDLSE 0010 XMTE 0001 COLE PHY Select 8000 10BASE_T PHY 8101 HomeRun PHY 8202 External PHY Am79C978 219 ABSOLUTE MAXIMUM RATINGS OPERATING RANGES Storage Temperature . . . . . . . . . . . . -65C to +150C Commercial (C) Devices Ambient Temperature. . . . . . . . . . . . . -65C to +70C Temperature (TA) . . . . . . . . . . . . . . . . . .0C to +70C Supply voltage with respect to VSSB, VSS . . . . . . . . . -0.3 V to 3.63 V Supply Voltages Stresses above those listed under Absolute Maximum Ratings may cause permanent device failure. Functionality at or above these limits is not implied. Exposure to Absolute Maximum Ratings for extended periods may affect device reliability. All inputs within the range: . . . . . . VSS - 0.5 V to 5.5 V (VDD, VDDR, VDD_PCI) . . . . . . . . . . . . . . . +3.3 V 10% Operating ranges define those limits between which the functionality of the device is guaranteed. DC CHARACTERISTICS OVER COMMERCIAL OPERATING RANGES unless otherwise specified Parameter Parameter Description Symbol Digital I/O (Non-PCI Pins) VIH Input HIGH Voltage VIL Input LOW Voltage Test Conditions Min Max Units 0.8 V V 0.4 V 2.0 IOL1 = 4 mA VOL Output LOW Voltage IOL2 = 6 mA IOL3 = 12 mA (Note 1) IOH1 = -4 mA VOH Output HIGH Voltage (Notes 2, 3) IOZ Output Leakage Current (Note 4) IIX Input Leakage Current (Note 5) IIL Input LOW Current (Note 6) IIH Input HIGH Current (Note 6) PCI Bus Interface - 5 V Signaling VIH Input HIGH Voltage VIL Input LOW Voltage IOZ Output Leakage Current (Note 4) IIL Input LOW Current IIH Input HIGH Current IIX_PME Input Leakage Current (Note 7) VOH Output HIGH Voltage (Note 2) VOL Output LOW Voltage IOH2 = -2 mA (Note 3) 0 V |VTHS| (Note 1) Min Max Unit 250 375 ns 136 200 ns Note: RX pulses narrower than tPWDRD (min) will maintain internal Carrier Sense on. RX pulses wider than tPWKRD (max) will turn internal Carrier Sense off. tTETD TX 22206B-57 Figure 54. 10 Mbps Transmit (TX) Timing Diagram t(PWKRD) t(PWKRD) VTSQ+ RX VTSQtPWKRD 22206B-58 Figure 55. 10 Mbps Receive (RX) Timing Diagram 226 Am79C978 SWITCHING CHARACTERISTICS: MEDIA INDEPENDENT INTERFACE Parameter Symbol Transmit Timing tTVAL Parameter Name TX_EN and TXD valid from TX_CLK Test Condition Min Max Unit measured from Vilmax = 0.8 V or measured from Vihmin = 2.0V 0 25 ns (Note 1) Receive Timing tRSU tRH RX_DV, RX_ER, RXD setup to RX_CLK RX_DV, RX_ER, RXD hold to RX_CLK Management Cycle Timing tMHIGH MDC Pulse Width HIGH Time tMLOW MDC Pulse Width LOW Time tMCYC MDC Cycle Period tMSU MDIO setup to MDC measured from Vilmax = 0.8 V or measured from Vihmin = 2.0V 10 ns 10 ns 160 160 400 ns ns ns 10 ns 10 ns tMCYC tMSU ns (Note 1) measured from Vilmax = 0.8 V or measured from Vihmin = 2.0V (Note 1) CLOAD = 390 pf CLOAD = 390 pf CLOAD = 390 pf CLOAD = 470 pf, measured from Vilmax = 0.8 V or measured from Vihmin = 2.0V (Note 1) CLOAD = 470 pf, tMH MDIO hold to MDC measured from Vilmax = 0.8 V or measured from Vihmin = 2.0V (Note 1) CLOAD = 470 pf, tMVAL MDIO valid from MDC measured from Vilmax = 0.8 V or measured from Vihmin = 2.0V, (Note 1) Notes: 1. MDIO valid measured at the exposed mechanical Media Independent Interface. 2. TXCLK and RXCLK frequency and timing parameters are defined for the external physical layer transceiver as defined in the IEEE 802.3u standard. They are not replicated here. Am79C978 227 SWITCHING WAVEFORMS Key to Switching Waveforms WAVEFORM INPUTS OUTPUTS Must be Steady Will be Steady May Change from H to L Will be Changing from H to L May Change from L to H Will be Changing from L to H Don't Care, Any Change Permitted Changing, State Unknown Does Not Apply Center Line is HighImpedance "Off" State KS000010-PAL SWITCHING TEST CIRCUITS IOL VTHRESHOLD Sense Point CL IOH 22206B-59 Figure 56. 228 Normal and Tri-State Outputs Am79C978 SWITCHING WAVEFORMS: SYSTEM BUS INTERFACE tHIGH 2.4 V 2.0 V CLK 2.0 V 1.5 V tLOW 1.5 V 0.8 V 0.8 V 0.4 V tCYC 22206B-60 Figure 57. CLK Waveform for 5 V Signaling tHIGH 0.6 VDD_PCI 0.5 VDD_PCI CLK 0.5 VDD_PCI 0.4 VDD_PCI tLOW 0.4 VDD_PCI 0.3 VDD_PCI 0.3 VDD_PCI 0.2 VDD_PCI tCYC 22206B-61 Figure 58. CLK Waveform for 3.3 V Signaling Tx Tx CLK AD[31:00], C/BE[3:0], PAR, FRAME, IRDY, TRDY, STOP, DEVSEL, IDSEL tSU tH tSU(GNT) tH(GNT) GNT 22206B-62 Figure 59. Input Setup and Hold Timing Am79C978 229 SWITCHING WAVEFORMS: SYSTEM BUS INTERFACE (CONTINUED) Tx Tx Tx CLK tVAL AD[31:00] C/BE[3:0], PAR, FRAME, IRDY, TRDY, STOP, DEVSEL, PERR, SERR MIN MAX Valid n Valid n+1 tVAL(REQ) MIN REQ MAX Valid n+1 Valid n 22206B-63 Figure 60. Output Valid Delay Timing Tx Tx Tx CLK tON AD[31:00], C/BE[3:0], PAR, FRAME, IRDY, TRDY, STOP, DEVSEL, PERR Valid n tOFF AD[31:00], C/BE[3:0], PAR, FRAME, IRDY, TRDY, STOP, DEVSEL, PERR Valid n 22206B-64 Figure 61. Output Tri-State Delay Timing EESK EECS EEDI 0 1 1 A6 A5 A4 A3 A2 A1 22206B-65 A0 EEDO D15 D14 D13 D2 D1 D0 22206B-65 Figure 62. 230 EEPROM Read Functional Timing Am79C978 SWITCHING WAVEFORMS: SYSTEM BUS INTERFACE (CONTINUED) tHIGH (EESK) tLOW (EESK) tSU (EEDO) EESK tH (EEDO) tVAL (EEDI,EECS) Stable EEDO tLOW (EECS) EECS EEDI 22206B-66 Figure 63. Automatic PREAD EEPROM Timing tJ3 2.0 V TCK tJ4 1.5 V 0.8 V 2.0 V 1.5 V 0.8 V tJ5 tJ6 tJ2 22206B-67 Figure 64. JTAG (IEEE 1149.1) TCK Waveform for 5 V Signaling Am79C978 231 SWITCHING WAVEFORMS: SYSTEM BUS INTERFACE (CONCLUDED) tJ2 TCK tJ7 tJ8 TDI, TMS tJ9 TDO tJ12 tJ11 Output Signals tJ13 tJ14 Input Signals 22206B-68 Figure 65. JTAG (IEEE 1149.1) Test Signal Timing 232 Am79C978 SWITCHING WAVEFORMS: MEDIA INDEPENDENT INTERFACE Vihmin Vilmax TX_CLK tTVAL Vihmin Vilmax TXD[3:0], TX_EN 22206B-69 Figure 66. Transmit Timing Vihmin Vilmax RX_CLK tRSU RXD[3:0], RX_ER, RX_DV tRH Vihmin Vilmax 22206B-70 Figure 67. Receive Timing tMHIGH 2.4 MDC 2.0 V 1.5 V 0.8 V tMLOW 0.4 2.0 V 1.5 V 0.8 V tMCYC 22206B-71 Figure 68. MDC Waveform Am79C978 233 SWITCHING WAVEFORMS: MEDIA INDEPENDENT INTERFACE (CONCLUDED) Vihmin Vilmax MDC tMSU tMH Vihmin Vilmax MDIO 22206B-72 Figure 69. Management Data Setup and Hold Timing Vihmin Vilmax MDC tTMVAL Vihmin Vilmax MDIO 22206B-73 Figure 70. Management Data Output Valid Delay Timing 234 Am79C978 PHYSICAL DIMENSIONS* PQL144 Thin Quad Flat Pack (measured in millimeters) 0.20 0.20 0.20 C A-B M M C H A-B A-B 0.05 MM/MM D S S D S 0.13 R. Min. 0.20 R. Max. S D Odd Lead Sides 144 Gage Plane 0.17 0.27 0.25 1 0.13 R. Min. 0.20 Min. 0.45 0.75 21.80 22.20 19.80 20.20 Detail X Even Lead Sides 0.25 BSC 0.17 0.27 With Lead Finish 0.17 0.23 36 0.09 0.16 0.09 0.20 Detail Y See Detail A Base Metal 19.80 20.20 0.20 M H A S -B D See Detail A S 0.05 S 0 Min. A-B 0.05 MM/MM 21.80 22.20 0.20 M C A-B S D 0.05 0.15 1.60 MAX S Seating Plane Detail Y 11 - 13 Detail X 1.35 1.45 0.17 0.27 0 - 7 0.08 0.08 C M C A-B S D S 1.60 MAX 0.50 BSC 16-038-PQT-1_AN EP 137 8-11-98 lv 11 - 13 1.00 REF. *For reference only. BSC is an ANSI standard for Basic Space Centering. Am79C978 235 PQR160 Plastic Quad Flat Pack (measured in millimeters) Pin 160 25.35 REF 27.90 28.10 31.00 31.40 Pin 120 Pin 1 I.D. 25.35 REF 27.90 28.10 31.00 31.40 Pin 40 Pin 80 3.20 3.60 0.65 BASIC 0.25 Min 3.95 MAX SEATING PLANE 16-038-PQR-1 PQR160 12-22-95 lv *For reference only. BSC is an ANSI standard for Basic Space Centering. 236 Am79C978 The contents of this document are provided in connection with Advanced Micro Devices, Inc. ("AMD") products. AMD makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this publication. Except as set forth in AMD's Standard Terms and Conditions of Sale, AMD assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. AMD's products are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or in any other application in which the failure of AMD's product could create a situation where personal injury, death, or severe property or environmental damage may occur. AMD reserves the right to discontinue or make changes to its products at any time without notice. (c) 1999 Advanced Micro Devices, Inc. All rights reserved. Trademarks AMD, the AMD logo, and combinations thereof are trademarks of Advanced Micro Devices, Inc. Auto-Poll, MACE, Magic Packet, PCnet, PCnet-FAST, PCnet-FAST+, PCnet-Home, PCnet-ISA, PCnet-ISA+, PCnet-ISA II, PCnet-32 are trademarks of Advanced Micro Devices, Inc. RLL25 is a trademark of Tut Systems, Inc. Other product names used in this publication are for identification purposes only and may be trademarks of their respective companies. 238 Am79C978 APPENDIX A Alternative Method for Initialization The controller may be initialized by performing I/O writes only. That is, data can be written directly to the appropriate control and status registers (CSR instead of reading from the initialization block in memory). The registers that must be written are shown in Table A-1. Table A-1. These register writes are followed by writing the START bit in CSR0. Registers for Alternative Initialization Method (Note 1) Control and Status Register Comment CSR2 IADR[31:16] (Note 2) CSR8 LADRF[15:0] CSR9 LADRF[31:16] CSR10 LADRF[47:32] CSR11 LADRF[63:48] CSR12 PADR[15:0] (Note 3) CSR13 PADR[31:16] (Note 3) CSR14 PADR[47:32] (Note 3) CSR15 MODE CSR24-25 BADR CSR30-31 BADX CSR47 TXPOLLINT CSR49 RXPOLLINT CSR76 RCVRL CSR78 XMTRL Note: 1. The INIT bit must not be set or the initialization block will be accessed instead. 2. Needed only if SSIZE32 =0. 3. Needed only if the physical address is different from the one stored in EEPROM or if there is no EEPROM present. Am79C978 A-1 A-2 Am79C978 APPENDIX B Look-Ahead Packet Processing (LAPP) Concept INTRODUCTION A driver for the controller would normally require that the CPU copy receive frame data from the controllers buffer space to the applications buffer space after the entire frame has been received by the controller. For applications that use a ping-pong windowing style, the traffic on the network will be halted until the current frame has been completely processed by the entire application stack. This means that the time between last byte of a receive frame arriving at the client's Ethernet controller and the client's transmission of the first byte of the next outgoing frame will be separated by: 1. The time that it takes the client's CPU interrupt procedure to pass software control from the current task to the driver, 2. Plus the time that it takes the client driver to pass the header data to the application and request an application buffer, 3. Plus the time that it takes the application to generate the buffer pointer and then return the buffer pointer to the driver, 4. Plus the time that it takes the client driver to transfer all of the frame data from the controller's buffer space into the application's buffer space and then call the application again to process the complete frame, 5. Plus the time that it takes the application to process the frame and generate the next outgoing frame, and 6. Plus the time that it takes the client driver to set up the descriptor for the controller and then write a TDMD bit to CSR0. The sum of these times can often be about the same as the time taken to actually transmit the frames on the wire, thereby, yielding a network utilization rate of less than 50 percent. An important thing to note is that the controller's data transfers to its buffer space are such that the system bus is needed by the controller for approximately 4 percent of the time. This leaves 96 percent of the system bus bandwidth for the CPU to perform some of the interframe operations in advance of the completion of network receive activity, if possible. The question then becomes: how much of the tasks that need to be performed between reception of a frame and transmission of the next frame can be performed before the reception of the frame actually ends at the network, and how can the CPU be instructed to perform these tasks during the network reception time. The answer depends upon exactly what is happening in the driver and application code, but the steps that can be performed at the same time as the receive data are arriving include as much as the first three steps and part of the fourth step shown in the sequence above. By performing these steps before the entire frame has arrived, the frame throughput can be substantially increased. A good increase in performance can be expected when the first three steps are performed before the end of the network receive operation. A much more significant performance increase could be realized if the controller could place the frame data directly into the application's buffer space; (i.e., eliminate the need for step 4.) In order to make this work, it is necessary that the application buffer pointer be determined before the frame has completely arrived, then the buffer pointer in the next descriptor for the receive frame would need to be modified in order to direct the controller to write directly to the application buffer. More details on this operation will be given later. An alternative modification to the existing system can gain a smaller but still significant improvement in performance. This alternative leaves step 4 unchanged in that the CPU is still required to perform the copy operation, but is allows a large portion of the copy operation to be done before the frame has been completely received by the controller, i.e., the CPU can perform the copy operation of the receive data from the controller's buffer space into the application buffer space before the frame data has completely arrived from the network. This allows the copy operation of step 4 to be performed concurrently with the arrival of network data, rather than sequentially, following the end of network receive activity. OUTLINE OF LAPP FLOW This section gives a suggested outline for a driver that utilizes the LAPP feature of the controller. Am79C978 B-1 Note: The labels in the following text are used as references in the timeline diagram that follows (Figure B-1). Setup The driver should set up descriptors in groups of three, with the OWN and STP bits of each set of three descriptors to read as follows: 11b, 10b, 00b. An option bit (LAPPEN) exists in CSR3, bit position 5; the software should set this bit. When set, the LAPPEN bit directs the controller to generate an INTERRUPT when STP has been written to a receive descriptor by the controller. ber 2 will be sufficient or not for this frame, but it has no way to tell except by trying to move the entire message into that space. Only when the message does not fit will it signal a buffer error condition--there is no need to panic at this point that it discovers that it does not yet own descriptor number 3. S2 The first task of the drivers interrupt service routing is to collect the header information from the controller's first buffer and pass it to the application. S3 The application will return an application buffer pointer to the driver. The driver will add an offset to the application data buffer pointer, since the controller will be placing the first portion of the message into the first and second buffers. (the modified application data buffer pointer will only be directly used by the controller when it reaches the third buffer.) The driver will place the modified data buffer pointer into the final descriptor of the group (#3) and will grant ownership of this descriptor to the controller. C5 Interleaved with S2, S3, and S4 driver activity, the controller will write frame data to buffer number 2. S4 The driver will next proceed to copy the contents of the controller's first buffer to the beginning of the application space. This copy will be to the exact (unmodified) buffer pointer that was passed by the application. S5 After copying all of the data from the first buffer into the beginning of the application data buffer, the driver will begin to poll the ownership bit of the second descriptor. The driver is waiting for the controller to finish filling the second buffer. C6 At this point, knowing that it had not previously owned the third descriptor and knowing that the current message has not ended (there is more data in the FIFO), the controller will make a last ditch lookahead to the final (third) descriptor. This time the ownership will be TRUE (i.e., the descriptor belongs tot he controller), because the driver wrote the application pointer into this descriptor and then changed the ownership to give the descriptor to the controller back at S3. Note that if steps S1, S2, and S3 have not completed at this time, a BUFF error will result. C7 After filling the second buffer and performing the last chance lookahead to the next descriptor, the controller will write the status and change the ownership bit of descriptor number 2. Flow The controller polls the current receive descriptor at some point in time before a message arrives. The controller determines that this receive buffer is OWNed by the controller and it stores the descriptor information to be used when a message does arrive. N0 Frame preamble appears on the wire, followed by SFD and destination address. N1 The 64th byte of frame data arrives from the wire. This causes the controller to begin frame data DMA operations to the first buffer. C0 When the 64th byte of the message arrives, the controller performs a lookahead operation to the next receive descriptor. This descriptor should be owned by the controller. C1 The controller intermittently requests the bus to transfer frame data to the first buffer as it arrives on the wire. S1 The driver remains idle. C2 When the controller has completely filled the first buffer, it writes status to the first descriptor. C3 When the first descriptor for the frame has been written, changing ownership from the controller to the CPU, the controller will generate an SRP INTERRUPT. (This interrupt appears as a RINT interrupt in CSR0). S1 The SRP INTERRUPT causes the CPU to switch tasks to allow the controller's driver to run. C4 During the CPU interrupt-generated task switching, the controller is performing a lookahead operation to the third descriptor. At this point in time, the third descriptor is owned by the CPU. Note: Even though the third buffer is not owned by the controller, existing AMD Ethernet controllers will continue to perform data DMA into the buffer space that the controller already owns (i.e., buffer number 2). The controller does not know if buffer space in buffer num- B-2 Am79C978 S6 C8 N2 After the ownership of descriptor number 2 has been changed by the controller, the next driver poll of the second descriptor will show ownership granted to the CPU. The driver now copies the data from buffer number 2 into the middle section of the application buffer space. This operation is interleaved with the C7 and C8 operations. The controller will perform data DMA to the last buffer, whose pointer is pointing to application space. Data entering the least buffer will not need the infamous double copy that is required by existing drivers, since it is being placed directly into the application buffer space. The message on the wire ends. S7 When the driver completes the copy of buffer number 2 data to the application buffer space, it begins polling descriptor number 3. C9 When the controller has finished all data DMA operations, it writes status and changes ownership of descriptor number 3. S8 The driver sees that the ownership of descriptor number 3 has changed, and it calls the application to tell the application that a frame has arrived. S9 The application processes the received frame and generates the next TX frame, placing it into a TX buffer. S10 The driver sets up the TX descriptor for the controller. Am79C978 B-3 Ethernet Wire activity: Ethernet Controller activity: Software activity: S10: Driver sets up TX descriptor. S9: Application processes packet, generates TX packet. S8: Driver calls application to tell application that packethas arrived. } C9: Controller writes descriptor #3. S7: Driver polls descriptor of buffer #3. N2:EOM C8: Controller is performing intermittent bursts of DMA to fill data buffer #3. Buffer #3 C6: "Last chance" lookahead to descriptor #3 (OWN). S4: Driver copies data from buffer #1 to the application buffer. S3: Driver writes modified application pointer to descriptor #3. Packet data arriving C5: Controller is performing intermittent bursts of DMA to fill data buffer #2 C4: Lookahead to descriptor #3 (OWN). C3: SRP interrupt is generated. S5: Driver polls descriptor #2. } Buffer #2 } C7: Controller writes descriptor #2. S6: Driver copies data from buffer #2 to the application buffer. S2: Driver call to application to get application buffer pointer. S1: Interrupt latency. } C2: Controller writes descriptor #1. C1: Controller is performing intermittent bursts of DMA to fill data buffer #1. Buffer #1 S0: Driver is idle. C0: Lookahead to descriptor #2. { N1: 64th byte of packet data arrives. N0: Packet preamble, SFD and destination address are arriving. 22206B-B1 Figure B-1. LAPP Timeline B-4 Am79C978 LAPP Software Requirements Software needs to set up a receive ring with descriptors formed into groups of three. The first descriptor of each group should have OWN = 1 and STP = 1, the second descriptor of each group should have OWN = 1 and STP = 0. The third descriptor of each group should have OWN = 0 and STP = 0. The size of the first buffer (as indicated in the first descriptor) should be at least equal to the largest expected header size; however, for maximum efficiency of CPU utilization, the first buffer size should be larger than the header size. It should be equal to the expected number of message bytes, minus the time needed for interrupt latency and minus the application call latency, minus the time needed for the driver to write to the third descriptor, minus the time Descriptor #1 OWN = 1 STP = 1 SIZE = A-(S1+S2+S3+S4+S6) Descriptor #2 OWN = 1 STP = 0 SIZE = S1+S2+S3+S4 Descriptor #3 OWN = 0 STP = 0 SIZE = S6 Descriptor #4 OWN = 1 STP = 1 SIZE = A-(S1+S2+S3+S4+S6) Descriptor #5 OWN = 1 STP = 0 SIZE = S1+S2+S3+S4 Descriptor #6 OWN = 0 STP = 0 SIZE = S6 Descriptor #7 OWN = 1 STP = 1 SIZE = A-(S1+S2+S3+S4+S6) Descriptor #8 OWN = 1 STP = 0 SIZE = S1+S2+S3+S4 Descriptor #9 OWN = 0 STP = 0 SIZE = S6 needed for the drive to copy data from buffer number 2 to the application buffer space. Note that the time needed for the copies performed by the driver depends upon the sizes of the second and third buffers, and that the sizes of the second and third buffers need to be set according to the time needed for the data copy operations. This means that an iterative self-adjusting mechanism needs to be placed into the software to determine the correct buffer sizing for optimal operation. Fixed values for buffer sizes may be used; in such a case, the LAPP method will still provide a significant performance increase, but the performance increase will not be maximized. Figure B-2 illustrates this setup for a receive ring size of 9. A = Expected message size in bytes S1 = Interrupt latency S2 = Application call latency S3 = Time needed for driver to write to third descriptor S4 = Time needed for driver to copy data from buffer #1 to application buffer space S6 = Time needed for driver to copy data from buffer #2 to application buffer space Note that the times needed for tasks S1, S2, S3, S4, and S6 should be divided by 0.8 microseconds to yield an equivalent number of network byte times before subtracting these quantities from the expected message size A. 22206B-B2 Figure B-2. LAPP 3 Buffer Grouping LAPP Rules for Parsing Descriptors When using the LAPP method, software must use a modified form of descriptor parsing as follows: n Software will examine OWN and STP to determine where an RCV frame begins. RCV frames will only begin in buffers that have OWN = 0 and STP = 1. n Software shall assume that a frame continues until it finds either ENP = 1 or ERR = 1. n Software must discard all descriptors with OWN = 0 and STP = 0 and move to the next descriptor when searching for the beginning of a new frame; ENP and ERR should be ignored by software during this search. n Software cannot change an STP value in the receive descriptor ring after the initial setup of the ring is complete, even if software has ownership of the STP Am79C978 B-5 descriptor, unless the previous STP descriptor in the ring is also OWNED by the software. When LAPPEN = 1, then hardware will use a modified form of descriptor parsing as follows: n The controller will examine OWN and STP to determine where to begin placing an RCV frame. A new RCV frame will only begin in a buffer that has OWN = 1 and STP =1. n The controller will always obey the OWN bit for determining whether or not it may use the next buffer for a chain. used for receive purposes by the controller, and the driver must recognize this. (The driver will recognize this if it follows the software rules.) The controller will ignore all descriptors with OWN = 0 and STP = 0 and move to the next descriptor when searching for a place to begin a new frame. In other words, the controller is allowed to skip entries in the ring that it does not own, but only when it is looking for a place to begin a new frame. Some Examples of LAPP Descriptor Interaction n The controller will always mark the end of a frame with either ENP = 1 or ERR = 1. Choose an expected frame size of 1060 bytes. Choose buffer sizes of 800, 200, and 200 bytes. The controller will discard all descriptors with OWN = 1 and STP = 0 and move to the next descriptor when searching for a place to begin a new frame. It discards these descriptors by simply changing the ownership bit from OWN = 1 to OWN = 0. Such a descriptor is un- n Example 1: Assume that a 1060 byte frame arrives correctly, and that the timing of the early interrupt and the software is smooth. The descriptors will have changed from: Before the Frame Arrives After the Frame Arrives Descriptor Number OWN STP ENP OWN STP ENPb Comments (After Frame Arrival) 1 1 1 x 0 1 0 Bytes 1-800 2 1 0 X 0 0 0 Bytes 801-1000 3 0 0 X 0 0 1 Bytes 1001-1060 4 1 1 X 1 1 X Controller's current location 5 1 0 X 1 0 X Not yet used 6 0 0 X 0 0 X Not yet used etc. 1 1 X 1 1 X Net yet used a a. & b. ENP or ERR. n Example 2: Assume that instead of the expected 1060 byte frame, a 900 byte frame arrives, either because there was an error in the network, or be- cause this is the last frame in a file transmission sequence. Before the Frame Arrives Descriptor Number OWN STP 1 1 2 1 3 0 After the Frame Arrives Comments (After Frame Arrival) ENPa OWN STP ENPb 1 x 0 1 0 Bytes 1-800 0 X 0 0 0 Bytes 801-1000 0 X 0 0 ?* Discarded buffer 4 1 1 X 1 1 X Controller's current location 5 1 0 X 1 0 X Not yet used 6 0 0 X 0 0 X Not yet used etc. 1 1 X 1 1 X Net yet used a. & b. ENP or ERR. Note: The controller might write a ZERO to ENP location in the third descriptor. Here are the two possibilities: modified buffer pointer into the third descriptor, then the controller will write a ZERO to ENP for this buffer and will write a ZERO to OWN and STP. 1. If the controller finishes the data transfers into buffer number 2 after the driver writes the application 2. If the controller finishes the data transfers into buffer number 2 before the driver writes the applications B-6 Am79C978 modified buffer point into the third descriptor, then the controller will complete the frame in buffer number 2 and then skip the then unowned third buffer. In this case, the controller will not have had the opportunity to RESET the ENP bit in this descriptor, and it is possible that the software left this bit as ENP = 1 from the last time through the ring. Therefore, the software must treat the location as a don't care. The rule is, after finding ENP = 1 (or ERR = 1) in descriptor number 2, the software must ignore ENP bits until it finds the next STP = 1. n Example 3: Assume that instead of the expected 1060 byte frame, a 100 byte frame arrives, because there was an error in the network, or because this is the last frame in a file transmission sequence, or perhaps because it is an acknowledge frame. *Same as note in example 2 above, except that in this case, it is very unlikely that the driver can respond to the interrupt and get the pointer from the application before the controller has completed its poll of the next descriptors. This means that for almost all occurrences of this case, the controller will not find the OWN bit set for this descriptor and, therefore, the ENP bit will almost always contain the old value, since the controller will not have had an opportunity to modify it. **Note that even though the controller will write a ZERO to this ENP location, the software should treat the location as a don't care, since after finding the ENP = 1 in descriptor number 2, the software should ignore ENP bits until it finds the next STP = 1. Before the Frame Arrives After the Frame Arrives Descriptor Number OWN STP ENP OWN STP ENPb Comments (After Frame Arrival) 1 1 1 x 0 1 0 Bytes 1-800 2 1 0 X 0 0 0** Discarded buffer 3 0 0 X 0 0 ? Discarded buffer 4 1 1 X 1 1 X Controller's current location 5 1 0 X 1 0 X Not yet used 6 0 0 X 0 0 X Not yet used etc. 1 1 X 1 1 X Net yet used a a. & b.ENP or ERR. Buffer Size Tuning For maximum performance, buffer sizes should be adjusted depending upon the expected frame size and the values of the interrupt latency and application call latency. The best driver code will minimize the CPU utilization while also minimizing the latency from frame end on the network to the frame sent to application from driver (frame latency). These objectives are aimed at increasing throughput on the network while decreasing CPU utilization. Note: The buffer sizes in the ring may be altered at any time that the CPU has ownership of the corresponding descriptor. The best choice for buffer sizes will maximize the time that the driver is swapped out, while minimizing the time from the last byte written by the controller to the time that the data is passed from the driver to the application. In the diagram, this corresponds to maximizing S0, while minimizing the time between C9 and S8. (the timeline happens to show a minimal time from C9 to S8.) Note: By increasing the size of buffer number 1, we increase the value of S0. However, when we increase the size of buffer number 1, we also increase the value of S4. If the size of buffer number 1 is too large, then the driver will not have enough time to perform tasks S2, S3, S4, S5, and S6. The result is that there will be delay from the execution of task C9 until the execution of task S8. A perfectly timed system will have the values for S5 and S7 at a minimum. An average increase in performance can be achieved, if the general guidelines of buffer sizes in Figure 2 is followed. However, as was noted earlier, the correct sizing for buffers will depend upon the expected message size. There are two problems with relating expected message size with the correct buffer sizing: 1. Message sizes cannot always be accurately predicted, since a single application may expect different message sizes at different times. Therefore, the buffer sizes chosen will not always maximize throughput. 2. Within a single application, message sizes might be somewhat predictable, but when the same driver is to be shared with multiple applications, there may not be a common predictable message size. Additional problems occur when trying to define the correct sizing because the correct size also depends upon the interrupt latency, which may vary from system to system, depending upon both the hardware and the software installed in each system. In order to deal with the unpredictable nature of the message size, the driver can implement a self-tuning Am79C978 B-7 mechanism that examines the amount of time spent in tasks S5 and S7. As such, while the driver is polling for each descriptor, it could count the number of poll operations performed and then adjust the number 1 buffer size to a larger value, by adding "t" bytes to the buffer count, if the number of poll operations was greater than "x." If fewer than "x" poll operations were needed for each of S5 and S7, then software should adjust the buffer size to a smaller value by subtracting "y" bytes from the buffer count. Experiments with such a tuning mechanism must be performed to determine the best values for "x" and "y." Note: Whenever the size of buffer number 1 is adjusted, buffer sizes for buffer number 2 and buffer number 3 should also be adjusted. In some systems, the typical mix of receive frames on a network for a client application consists mostly of large data frames, with very few small frames. In this case, for maximum efficiency of buffer sizing, when a frame arrives under a certain size limit, the driver should not adjust the buffer sizes in response to the short frame. An Alternative LAPP Flow: Two-Interrupt Method An alternative to the above suggested flow is to use two interrupts, one at the start of the receive frame and the other at the end of the receive frame, instead of just looking for the SRP interrupt as described above. This alternative attempts to reduce the amount of time that the software wastes while polling for descriptor own bits. This time would then be available for other CPU tasks. It also minimizes the amount of time the CPU needs for data copying. This savings can be applied to other CPU tasks. B-8 The time from the end of frame arrival on the wire to delivery of the frame to the application is labeled as frame latency. For the one-interrupt method, frame latency is minimized, while CPU utilization increases. For the two-interrupt method, frame latency becomes greater, while CPU utilization decreases. See Figure B-3. Note: Some of the CPU time that can be applied to non-Ethernet tasks is used for task switching in the CPU. One task switch is required to swap a non-Ethernet task into the CPU (after S7A) and a second task switch is needed to swap the Ethernet driver back in again (at S8A). If the time needed to perform these task switches exceeds the time saved by not polling descriptors, then there is a net loss in performance with this method. Therefore, the LAPP method implemented should be carefully chosen. Figure B-4 shows the buffer sizing for the two-interrupt method. Note that the second buffer size will be about the same for each method. There is another alternative which is a marriage of the two previous methods. This third possibility would use the buffer sizes set by the two-interrupt method, but would use the polling method of determining frame end. This will give good frame latency but at the price of very high CPU utilization. And still, there are even more compromise positions that use various fixed buffer sizes and, effectively, the flow of the one-interrupt method. All of these compromises will reduce the complexity of the one-interrupt method by removing the heuristic buffer sizing code, but they all become less efficient than heuristic code would allow. Am79C978 Software activity: Ethernet Controller activity: Ethernet Wire activity: S10: Driver sets up TX descriptor. S9: Application processes packet, generates TX packet. S8: Driver calls application to tell application that packethas arrived. S8A: Interrupt latency. } C10: ERP interrupt is generated. } C9: Controller writes descriptor #3. } C8: Controller is performing intermittent bursts of DMA to fill data buffer #3. N2:EOM Buffer #3 C7: Controller writes descriptor #2. S7: Driver is swapped out, allowing a non-Ethernet application to run. S7A: Driver Interrupt Service Routine executes RETURN. S6: Driver copies data from buffer #2 to the application buffer. S5: Driver polls descriptor #2. C6: "Last chance" lookahead to descriptor #3 (OWN). S4: Driver copies data from buffer #1 to the application buffer. S3: Driver writes modified application pointer to descriptor #3. Packet data arriving C4: Lookahead to descriptor #3 (OWN). C3: SRP interrupt is generated. } Buffer #2 } C5: Controller is performing intermittent bursts of DMA to fill data buffer #2 S2: Driver call to application to get application buffer pointer. S1: Interrupt latency. } C2: Controller writes descriptor #1. C1: Controller is performing intermittent bursts of DMA to fill data buffer #1. Buffer #1 S0: Driver is idle. C0: Lookahead to descriptor #2. { N1: 64th byte of packet data arrives. N0: Packet preamble, SFD and destination address are arriving. 22206B-B3 Figure B-3. LAPP Timeline for Two-Interrupt Method Am79C978 B-9 Descriptor #1 Descriptor #2 OWN = 1 STP = 1 SIZE = HEADER_SIZE (minimum 64 bytes) OWN = 1 SIZE = S1+S2+S3+S4 STP = 0 Descriptor #3 OWN = 0 STP = 0 SIZE = 1518 - (S1+S2+S3+S4+HEADER_SIZE) Descriptor #4 OWN = 1 STP = 1 SIZE = HEADER_SIZE (minimum 64 bytes) Descriptor #5 OWN = 1 SIZE = S1+S2+S3+S4 Descriptor #6 OWN = 0 STP = 0 SIZE = 1518 - (S1+S2+S3+S4+HEADER_SIZE) Descriptor #7 OWN = 1 STP = 1 SIZE = HEADER_SIZE (minimum 64 bytes) Descriptor #8 OWN = 1 SIZE = S1+S2+S3+S4 Descriptor #9 OWN = 0 STP = 0 SIZE = 1518 - (S1+S2+S3+S4+HEADER_SIZE) STP = 0 STP = 0 A = Expected message size in bytes S1 = Interrupt latency S2 = Application call latency S3 = Time needed for driver to write to third descriptor S4 = Time needed for driver to copy data from buffer #1 to application buffer space S6 = Time needed for driver to copy data from buffer #2 to application buffer space Note that the times needed for tasks S1, S2, S3, S4, and S6 should be divided by 0.8 microseconds to yield an equivalent number of network byte times before subtracting these quantities from the expected message size A. 22206B-B4 Figure B-4. B-10 LAPP 3 Buffer Grouping for Two-interrupt Method Am79C978 Numerics 1 Mbps HomePNA PHY Internal Registers 179 1 Mbps HomePNA PHY Management Registers 214 10 Mbps Receive (RX) Timing Diagram 227 10 Mbps Transmit (TX) Timing Diagram 227 10/100 Mbps operation 2 10/100 Media Access Control 65 10/100 Media Access Controller 65 10BASE-T 227 10BASE-T Block 98 10BASE-T I/O Buffer Power 32 10BASE-T Mode 224 10BASE-T PDX Analog Ground 32 10BASE-T PDX Block Power 32 10BASE-T PDX Digital Ground 32 10BASE-T PHY Management Registers 213 10BASE-T PHY Management Registers (TBRs) 179 10BASE-T Physical Layer 98 14795 Tabtle Table 44. R/TLEN Decoding (SSIZE32 = 0) 199 16937 Tabtle Table 36. Software Styles 163 16-Bit Software Model 61 24958 Tabtle Table 26. Software Styles 135 24981 Tabtle Table 35. Interface Pin Assignment 161 C/BE 26 RXD 30 TXD 30 AD 26 31439 Tabtle Table 25. Loopback Configuration 128 32-Bit Software Model 62 34313 Tabtle Table 19. Table 18. PCI Configuration Space Layout 95 38779 Tabtle Table 49. Transmit Descriptor (SW- STYLE = 0) 203 40675 TblTitlew Table 13. MII Control Frame Format 81 41807 TblTitle Table 11. Master Station Control Word Functions 81 A Absolute Maximum Ratings 220 ACCESS ID Intervals 76 ACCESS ID Values 78 Address and Data 26 Address Match Logic 200 Address Matching 71 Address Parity Error Response 41 Address PROM Space 96 Advanced Configuration and Power Interface (ACPI) specification 1 Advanced Parity Error Handling 52 AID Receive Timing 78 AID Transmit Timing 78 Alternative Method for Initialization 1 Am79C978 10BASE-T PHY Management Register Set 188 Am79C978 Programmable Register 215 An Alternative LAPP Flow Two-Interrupt Method 8 Analog PLL Power 32 ANR6 Auto-Negotiation Expansion Register (Register 6) 194 APDW Values 169 APP 3 Buffer Grouping for Two-interrupt Method 10 Automatic EEPROM Read Operation 84 Automatic Pad Generation 69 Automatic Pad Stripping 72 Automatic PREAD EEPROM Timing 232 Auto-Negotiation 99 Auto-Negotiation Capabilities 99 Auto-PollTM 1 B Basic Burst Read Transfer 43 Basic Burst Write Transfer 45 Basic Non-Burst Read Transfer 43 Basic Non-Burst Write Transfer 45 BCR Registers 146 BCR0 Am79C978 1 Master Mode Read Active 145 BCR1 Master Mode Write Active 145 BCR16 I/O Base Address Lower 155 BCR17 I/O Base Address Upper 155 BCR18 Burst and Bus Control Register 156 BCR19 EEPROM Control and Status 158 BCR2 Miscellaneous Configuration 145 BCR20 Software Style 161 BCR22 PCI Latency Register 163 BCR23 PCI Subsystem Vendor ID Register 163 BCR24 PCI Subsystem ID Register 164 BCR25 SRAM Size Register 164 BCR26 SRAM Boundary Register 164 BCR27 SRAM Interface Control Register 165 BCR28 Expansion Bus Port Address Lower (Used for Flash/EPROM and SRAM Accesses) 166 BCR29 Expansion Port Address Upper (Used for Flash/EPROM Accesses) 167 BCR30 Expansion Bus Data Port Register 167 BCR31 Software Timer Register 168 BCR32 PHY Control and Status Register 168 BCR32 PHY Control and Status Register 168 BCR33 PHY Address Register 170 BCR34 PHY Management Data Register 171 BCR35 PCI Vendor ID Register 171 BCR36 PCI Power Management Capabilities (PMC) 2 Alias Register 172 BCR37 PCI DATA Register Zero (DATA0) Alias Register 172 BCR38 PCI DATA Register 1 (DATA1) Alias Register 172 PCI DATA Register One (DATA1) Alias Register 172 BCR39 PCI DATA Register 0 (DATA2) Alias Register 172 PCI DATA Register Two (DATA2) Alias Register 172 BCR4 LED 0 Status 147 BCR40 PCI DATA Register 3 (DATA3) Alias Register 173 PCI Data Register Three (DATA3) Alias Register 173 BCR41 PCI DATA Register 4 (DATA4) Alias Register 173 BCR42 PCI DATA Register 5 (DATA5) Alias Register 174 PCI DATA Register Five (DATA5) Alias Register 174 BCR43 PCI DATA Register 6 (DATA6) Alias Register 174 BCR44 PCI DATA Register Seven (DATA7) Alias Register 174 PCI DATA Register7 (DATA7) Alias Register 174 BCR45 OnNow Pattern Matching Register 1 175 BCR46 OnNow Pattern Matching Register 2 175 BCR47 OnNow Pattern Matching Register #3 176 OnNow Pattern Matching Register 3 176 BCR48 LED4 Status 176 BCR49 PHY Select 178 BCR5 Am79C978 LED1 Status 149 BCR50-BCR55 Reserved Locations 178 BCR6 LED2 Status 151 BCR7 LED3 Status 153 BCR9 Full-Duplex Control 155 Blanking Interval Speed Settings 79 BLOCK DIAGRAM 4 Block Diagram Low Latency Receive Configuration 83 Block Diagram No SRAM Configuration 82 Board Interface 28 Boundary Scan Circuit 91 Boundary Scan Register 91 BSR Mode Of Operation 91 Buffer Management 60 Buffer Management Unit 3, 59 Buffer Size Tuning 7 Burst FIFO DMA Transfers 57 Burst Write Transfer 46 Bus Acquisition 42, 43 Bus Command and Byte Enables 26 Bus Configuration Registers 145, 212, 217 Bus Configuration Registers (BCRs) 145 Bus Grant 26 Bus Master DMA Transfers 43 Bus Request 27 by Driver Type 24 C CLK 26 CLK Waveform for 3.3 V Signaling 230 CLK Waveform for 5 V Signaling 230 CLK_FAC Values 166 Clock 26 Clock Interface 31 Clock Timing 222, 225 COL 30 Collision 30 Collision Detect Function 99 Collision Handling 68 CONNECTION DIAGRAM (144 TQFP) 16 CONNECTION DIAGRAM (160 PQFP) 17 Contents 5 Control and Status Registers 112, 208, 215 CRS 30 Crystal 32 Crystal Oscillator In 32 Crystal Oscillator Out 32 CSR0 Controller Status and Control Register 112 CSR1 Initialization Block Address 0 115 CSR10 Logical Address Filter 2 125 CSR100 Bus Timeout 141 CSR11 Logical Address Filter 3 126 CSR112 Missed Frame Count 142 CSR114 Receive Collision Count 142 CSR116 OnNow Power Mode Register 142 CSR12 Physical Address Register 0 126 CSR122 Advanced Feature Control 143 CSR124 Test Register 1 143 CSR125 MAC Enhanced Configuration Control 144 CSR13 Physical Address Register 1 126 CSR14 Physical Address Register 2 126 CSR15 Mode 127 CSR16 Initialization Block Address Lower 128 CSR17 Initialization Block Address Upper 128 CSR18 Current Receive Buffer Address Lower 128 CSR19 Current Receive Buffer Address Upper 128 CSR2 Initialization Block Address 1 115 CSR20 Current Transmit Buffer Address Lower 129 CSR21 Current Transmit Buffer Address Upper 129 CSR22 Next Receive Buffer Address Lower 129 CSR23 Am79C978 3 Next Receive Buffer Address Upper 129 CSR24 Base Address of Receive Ring Lower 129 CSR25 Base Address of Receive Ring Upper 129 CSR26 Next Receive Descriptor Address Lower 129 CSR27 Next Receive Descriptor Address Upper 130 CSR28 Current Receive Descriptor Address Lower 130 CSR29 Current Receive Descriptor Address Upper 130 CSR3 Interrupt Masks and Deferral Control 115 CSR30 Base Address of Transmit Ring Lower 130 CSR31 Base Address of Transmit Ring Upper 130 CSR32 Next Transmit Descriptor Address Lower 130 CSR33 Next Transmit Descriptor Address Upper 130 CSR34 Current Transmit Descriptor Address Lower 131 CSR35 Current Transmit Descriptor Address Upper 131 CSR36 Next Next Receive Descriptor Address Lower 131 CSR37 Next Next Receive Descriptor Address 131 Next Next Receive Descriptor Address Upper 131 CSR38 Next Next Transmit Descriptor Address Lower 131 CSR39 Next Next Transmit Descriptor Address Upper 131 CSR4 Test and Features Control 118 CSR40 Current Receive Byte Count 131 CSR41 4 Current Receive Status 132 CSR42 Current Transmit Byte Count 132 CSR43 Current Transmit Status 132 CSR44 Next Receive Byte Count 132 CSR45 Next Receive Status 132 CSR46 Transmit Poll Time Counter 132 CSR47 Transmit Polling Interval 133 CSR48 Receive Poll Time Counter 133 CSR49 Receive Polling Interval 133 CSR5 Extended Control and Interrupt 1 119 CSR58 Software Style 134 CSR6 RX/TX Descriptor Table Length 122 CSR60 Previous Transmit Descriptor Address Lower 136 CSR61 Previous Transmit Descriptor Address Upper 135, 136 CSR62 Previous Transmit Byte Count 136 CSR63 Previous Transmit Status 136 CSR64 Next Transmit Buffer Address Lower 136 CSR65 Next Transmit Buffer Address Upper 136 CSR66 Next Transmit Byte Count 137 CSR67 Next Transmit Status 137 CSR7 Extended Control and Interrupt 2 122 CSR72 Receive Ring Counter 137 CSR74 Transmit Ring Counter 137 CSR76 Receive Ring Length 137 Am79C978 CSR78 Transmit Ring Length 137 CSR8 Logical Address Filter 0 125 CSR80 DMA Transfer Counter and FIFO Threshold Control 138 CSR82 Transmit Descriptor Address Pointer Lower 140 CSR84 DMA Address Register Lower 140 CSR85 DMA Address Register Upper 140 CSR86 Buffer Byte Counter 140 CSR88 Chip ID Register Lower 141 CSR89 Chip ID Register Upper 141 CSR9 Logical Address Filter 1 125 CSR92 Ring Length Conversion 141 Cycle Frame 26 D Data Receive Timing 79 Data Symbol RLL25 Encoding 80 Data Symbols 79 Data Transmit Timing 79 DC CHARACTERISTICS OVER COMMERCIAL OPERATING RANGES 220 DC CHARACTERISTICS OVER COMMERCIAL OPERATING RANGES unless otherwise specified 220 Description of the Methodology 81 Descriptor DMA Transfers 54 Descriptor Ring Read In Burst Mode 55 Descriptor Ring Write In Burst Mode 56 Descriptor Ring Write In Non-Burst Mode 56 Descriptor Rings 60 Destination Address Handling 66 Detailed Functions 75 Device ID Register 91 Device Select 26 DEVSEL 26 Digital Ground (8 Pins) 32 Digital I/O (Non-PCI Pins) 220 Digital Power (6 Pins) 32 Direct Access to the Interface 84 Direct Memory Access (DMA) 2 Direct SRAM Access 82 Disconnect Of Burst Transfer 40 Disconnect Of Slave Burst Transfer - Host Inserts Wait States 41 Disconnect Of Slave Burst Transfer - No Host Wait States 40 Disconnect Of Slave Cycle When Busy 40 Disconnect When Busy 40 Disconnect With Data Transfer 46, 47 Disconnect Without Data Transfer 47, 48 DISTINCTIVE CHARACTERISTICS 1 Double Word I/O Mode 97 DVDDA 32 DVDDA_HR 32 DVDDD 32 DVDDRX, DVDDTX 32 DVSSD 32 DVSSX 32 E EBCS Values 166 EECS 29 EEDET Setting 161 EEDI 29 EEDO 29 EEPROM 86 EEPROM Auto-Detection 84 EEPROM Chip Select 29 EEPROM Data In 29 EEPROM Data Out 29 EEPROM Interface 29, 83, 84 EEPROM MAP 85 EEPROM Map 86 EEPROM Read Functional Timing 231 EEPROM Serial clock 30 EEPROM Timing 223 EEPROM-Programmable Registers 84 EESK 30 Error Detection 66 escriptor Ring Read In Non-Burst Mode 55 Ethernet controllers in the PCnet Family 3 Ethernet Network Interfaces 31 Expansion ROM Read 39 Expansion ROM Transfers 39 External Clock 225 External Clock/Crystal Select 31 F FIFO Burst Write At End Of Unaligned Buffer 58 Am79C978 5 FIFO Burst Write At Start Of Unaligned Buffer 58 FIFO DMA Transfers 57 Flow, LAPP 2 FMDC Values 169 FRAME 26 Frame Format at the MII Interface Connection 35 Framing 65, 75 Full-Duplex Link Status LED Support 74 Full-Duplex Operation 73 G GENERAL DESCRIPTION 2 GNT 26 H H_RESET 94 Header AID Remote Control Word Commands 81 Home Networking Controller 1 Home Phoneline Networking Alliance (HomePNA) 1 HomePNA Analog Ground 32 HomePNA Analog Power 32 HomePNA Digital Power 32 HomePNA PHY Framing 76 HomePNA PHY Network Interface 31 HomePNA Physical Layer (PHY) 1 HPR0 HomePNA PHY MII Control (Register 0) 179 HPR1 HomePNA PHY MII Status (Register 1) 180 HPR16 HomePNA PHY Control (Register 16) 182, 183 HPR18 and HPR19 HomePNA PHY TxCOMM (Registers 18 and 19) 183 HPR2 and HPR3 HomePNA PHY MII PHY ID (Registers 2 and 3) 181 HPR20 and HPR21 HomePNA PHY RxCOMM (Registers 20 and 21) 184 HPR22 HomePNA PHY AID (Register 22) 184 HPR23 HomePNA PHY Noise Control (Register 23) 184 HPR24 HomePNA PHY Noise Control 2 (Register 24) 185 HPR25 6 HomePNA PHY Noise Statistics (Register 25) 185 HPR26 HomePNA PHY Event Status (Register 26) 186 HPR27 HomePNA PHY Event Status (Register 27) 186 HPR28 HomePNA PHY ISBI Control (Register 28) 186 HPR29 HomePNA PHY TX Control (Register 29) 187 HPR4-HPR7 HomePNA PHY Auto-Negotiation (Registers 4 - 7) 181 HRTXRXP/HRTXRXN 31 I I/O Buffer Ground (17 Pins) 32 I/O Buffer Power (7 Pins) 32 I/O Map In DWord I/O Mode (DWIO = 1) 98 I/O Map in DWord I/O Mode (DWIO = 1) 98 I/O Map In Word I/O Mode (DWIO = 0) 97 I/O Registers 96 I/O Resources 95 IDSEL 26 IEEE 1149.1 (1990) Test Access Port Interface 31, 91 IEEE 1149.1 Supported Instruction Summary 91 IEEE 802.3 Frame And Length Field Transmission Order 73 IEEE 802.3u 2 Initialization 59 Initialization Block 198 Initialization Block (SSIZE32 = 0) 198 Initialization Block (SSIZE32 = 1) 198 Initialization Block DMA Transfers 52 Initialization Block Read In Burst Mode 53 Initialization Block Read In Non-Burst Mode 53 Initialization Device Select 26 Initiator Ready 27 Input Setup and Hold Timing 230 Instruction Register and Decoding Logic 91 INTA 27 Integrated Controllers 15 integrated PCI Ethernet controller 2 Integrated Repeater/Hub Devices 15 Inter Packet Gap (IPG) 2 Interface Pin Assignment 161 Am79C978 Interrupt Request 27 Introduction 1 IRDY 27 IREF 31 J Jabber Function 99 JAM Signal 78 JTAG (IEEE 1149.1) TCK Waveform for 5 V Signaling 232 JTAG (IEEE 1149.1) Test Signal Timing 223, 233 K Key to Switching Waveforms 229 L LADRF 199 LAPP 3 Buffer Grouping 5 LAPP Software Requirements 5 LAPP Timeline 4 LAPP Timeline for Two-Interrupt Method 9 Late Collision 70 LED Control Logic 87 LED Default Configuration 87 LED Support 85 LED0 28 LED1 29 LED2 29 LED3 29 LED4 29 Legal I/O Accesses in Double Word I/O Mode (DWIO =1) 98 Legal I/O Accesses in Word I/O Mode (DWIO = 0) 97 Link Change Detect 88 listed by Group 20 Look-Ahead Packet Processing (LAPP) 2 Look-Ahead Packet Processing (LAPP) Concept 1 Loopback Configuration 128 Loopback Operation 73 Loss of Carrier 70 Low Latency Receive Configuration 82 M MAC 65, 66, 67 Magic Packet Mode 89 Magic PacketTM mode 1 magnetics module. IREF 31 Management Cycle Timing 228 Management Data Clock 31 Management Data Input/Output 31 Management Data Output Valid Delay Timing 235 Management Data Setup and Hold Timing 235 Management Interfaces 80 Manchester Encoder/Decoder 15 Master Abort 49, 51 Master Bus Interface Unit 42 Master Cycle Data Parity Error Response 51 Master Initiated Termination 48 MDC 31 MDC Waveform 234 MDIO 31 Media Access Controller (MAC) 1, 2 Media Access Management 67 Media Independent Interface 33 Medium Allocation 67 Microsoft OnNow 2 MII Interface 30 MII interface 2 MII Management Frames 35 MII Management Interface 34 MII Network Status Interface 34 MII Receive Interface 34 MII Transmit Interface 33 Miscellaneous Loopback Features 73 Mode 199 N NAND Tree Circuitry 92 NAND Tree Circuitry (160 PQFP 92 NAND Tree Circuitry (160 PQFP) 92 NAND Tree Pin Sequence (144 TQFP) 93 NAND Tree Pin Sequence (160 PQFP) 93 NAND Tree Testing 92 NAND Tree Waveform 94 Network Interfaces 33 Network Port Manager 36 Non-Burst FIFO DMA Transfers 57 Non-Burst Read Transfer 44 Non-Burst Write Transfer 45 Normal and Tri-State Outputs 229 O Offset 00h 102 Offset 02h 102 Offset 04h 103 Offset 06h 104 Offset 08h 105 Offset 09h 105 Offset 0Ah 105 Offset 0Bh 106 Offset 0Dh 106 Offset 0Eh 106 Am79C978 7 Offset 10h 106 Offset 14h 107 Offset 2Ch 107 Offset 2Eh 107 Offset 30h 108 Offset 34h 108 Offset 3Ch 108 Offset 3Dh 109 Offset 3Eh 109 Offset 3Fh 109 Offset 40h 109 Offset 41h 109 Offset 42h 109 Offset 44h 110 Offset 46h 111 Offset 47h 111 OnNow Functional Diagram 88 OnNow Pattern Match Mode 88 OnNow Wake-Up Sequence 87 Operating Ranges 220 ordering information 25 Other Data Registers 91 Outline of LAPP Flow 1 Output and Float Delay Timing 222 Output Tri-State Delay Timing 231 Output Tri-state Delay Timing 231 Output Valid Delay Timing 231 P PADR 199 PAR 27 Parity 27 Parity Error 27 Parity Error Response 41, 49 Pattern Match RAM 90 Pattern Match RAM (PMR) 88 PCI and JTAG Configuration Information 36 PCI Base-Class Register Offset 0Bh 106 PCI Bus Interface Pins - 3.3 V Signaling 220 PCI Bus Interface Pins - 5 V Signaling 220 PCI Bus Power Management Interface specification 2 PCI Capabilities Pointer Register 108 PCI Capability Identifier Register 109 PCI Command Register 103 PCI Command Register Offset 04h 103 PCI Configuration Registers 95, 101, 102, 207 PCI Configuration Space Layout 95 PCI Data Register 111 PCI Data Register Offset 47h 111 8 PCI Device ID Register 102 PCI Device ID Register Offset 02h 102 PCI Expansion ROM Base Address Register 108 PCI Header Type Register 106 PCI Header Type Register Offset 0Eh 106 PCI I/O Base Address Register 106 PCI I/O Base Address Register Offset 10h 106 PCI I/O Buffer Power (9 Pins) 32 PCI Interface 26 PCI Interrupt Line Register 108 PCI Interrupt Line Register Offset 3Ch 108 PCI Interrupt Pin Register 109 PCI Latency Timer Register 106 PCI MAX_LAT Register 109 PCI Memory Mapped I/O Base Address Register 107 PCI MIN_GNT Register 109 PCI Next Item Pointer Register 109 PCI Next Item Pointer Register Offset 41h 109 PCI PMCSR Bridge Support Extensions Register 111 PCI PMCSR Bridge Support Extensions Register Offset 46h 111 PCI Power Management Capabilities Register (PMC) 109 PCI Power Management Control/Status Register (PMCSR) 110 PCI Programming Interface Register 105 PCI Programming Interface Register Offset 09h 105 PCI Revision ID Register 105 PCI Status Register 104 PCI Status Register Offset 06h 104 PCI Sub-Class Register 105 PCI Sub-Class Register Offset 0Ah 105 PCI Subsystem ID Register 107 PCI Subsystem Vendor ID Register 107 PCI Vendor ID Register 102 PCI Vendor ID Register Offset 00h 102 PECL 225 PERR 27 PG 28 PHY Control and Management Block (PCM Block) 81 PHY Select Programming 158 PHY/MAC Interface 74 PHY_RST 31 PHYSICAL DIMENSIONS 236 Physical Layer Devices (Multi-Port) 15 Am79C978 Physical Layer Devices (Single-Port) 15 Pin Capacitance 221 Pin Descriptions 26 PIN DESIGNATIONS 24 PIN DESIGNATIONS (PQL144 20 PIN DESIGNATIONS (PQL144) 18 PIN DESIGNATIONS (PQR160) 19 listed by Group 22 PMD Interface 225 PMD Interface Timing (PECL) 226 PME 28 Polling 62 Power Good 28, 31 Power Management Event 28 Power Management Support 87 Power on Reset 95 Power Savings Mode 87 Power Supply Current 221, 224 Power Supply Pins 32 PQL144 236 PQR160 237 Preemption During Burst Transaction 48, 50 Preemption During Non-Burst Transaction 48, 50 R RAP Register Address Port 112 RAP Register 111 RDRA and TDRA 199 Receive Address Match 72 Receive Carrier Sense 30 Receive Clock 30 Receive Data 30 Receive Data Valid 30 Receive Descriptor (SWSTYLE = 0) 200 Receive Descriptor (SWSTYLE = 2) 200 Receive Descriptor (SWSTYLE = 3) 200 Receive Descriptor Table Entry 64 Receive Descriptors 200 Receive Exception Conditions 72 Receive FCS Checking 72 Receive Frame Queuing 64 Receive Function Programming 70 Receive Operation 70 Receive Symbol Timing 79 Receive Timing 228, 234 Receive Watermark Programming 138 Register Administration for 10BASE-T PHY Device 81 Register Programming Summary 215 Register Summary 207 Re-Initialization 59 RELATED AMD PRODUCTS 15 REQ 27 Reserved Register 10BASE-T Carrier Status Register (Register 23) 197 10BASE-T Configuration Register (Register 22) 197 Reserved Registers HPR8 - HPR15, HPR17 181 Reserved Registers (Registers 8-15, 18, 20-23, and 25-31) 194 Reset 28, 94 Reset Register 96 Reverse Polarity Detect 99 RLEN and TLEN 198 RLL 25 Coding Tree 80 RMD0 200, 201 RMD1 201 RMD2 202 RMD3 203 ROMTNG Programming Values 156 RST 28 Running Registers 102 RWU 29 RX_CLK 30 RX_DV 30 RX_ER 30 RX 31 S S_RESET 94 Serial Receive Data 31 Serial Transmit Data 31 SERR 28 Setup 2 Setup and Hold Timing 222 Setup Registers 101 Silence Interval (AID symbol 7) 78 Slave Bus Interface Unit 36 Slave Configuration Read 38 Slave Configuration Transfers 36 Slave Configuration Write 38 Slave Cycle Data Parity Error Response 42 Slave Cycle Termination 39 Slave I/O Transfers 37 Slave Read Using I/O Command 38 Slave Write Using Memory Command 39 Soft Reset Function 100 Am79C978 9 Software 163 Software Access 95 Software Interface 33 Software Interrupt Timer 65 Some Examples of LAPP Descriptor Interaction 6 SQE Test Error 70 SR2 Initialization Block Address 1 115 SRAM_BND Programming 165 Standard Products 25 STOP 28, 96 Stop 28 Supported Instructions 91 Suspend 59 Switching Characteristics Bus Interface 222 Media Independent Interface 228 Switching Test Circuits 229 SWITCHING WAVEFORMS 229 Switching Waveforms Expansion Bus Interface 236 General-Purpose Serial Interface 236 Media Independent Interface 234, 236 System Bus Interface 230 Symbol 0 (SYNC interval) 76 SYNC Receive Timing 76 SYNC Transmit Timing 76 System Bus Interface 33 System Error 28 T TAP Finite State Machine 91 Target Abort 47, 49 Target Initiated Termination 46 Target Ready 28 TBR0 10BASE-T PHY Control Register (Register 0) 189 TBR16 10BASE-T INTERRUPT Status and Enable Register (Register 16) 195 TBR17 10BASE-T PHY Control/Status Register (Register 17) 196 TBR19 10BASE-T PHY Management Extension Register (Register 19) 197 TBR2 191 10BASE-T PHY Identifier (Register 2) 191 TBR24 10 10BASE-T Summary Status Register (Register 24) 197 TBR3 10BASE-T PHY Identifier (Register 3) 191 TBR4 10BASE-T Auto-Negotiation Advertisement Register (Register 4) 192 TBR5 10BASE-T Auto-Negotiation Link Partner Ability Register (Register 5) 193 10BASE-T Auto-Negotiation Link Partner Ability Register (Register 5) - Base Page Forma 193 10BASE-T Auto-Negotiation Link Partner Ability Register (Register 5) - Next Page Format 193 TBR6 10BASE-T Auto-Negotiation Expansion Register (Register 6) 194 TBR7 10BASE-T Auto-Negotiation Next Page Register (Register 7) 194 TCK 31 TDI 31 TDO 31 Test Clock 31 Test Data In 31 Test Data Out 31 Test Mode Select 31 Test Registers 102 Time 76 Time Interval Unit 76 TMD0 204 TMD1 204 TMD2 205 TMD3 206 TMS 31 Transmit and Receive Message Data Encapsulation 65 Transmit Clock 30 Transmit Data 30 Transmit Data Symbol Timing 79 Transmit Descriptor (SWSTYLE = 2) 203 Transmit Descriptor (SWSTYLE = 3) 203 Transmit Descriptor Table Entry 63 Transmit Descriptors 203 Transmit Enable 31 Transmit Exception Conditions 70 Transmit FCS Generation 70 Am79C978 Transmit Function Programming 68 Transmit Operation 68 Transmit Start Point Programming 139 Transmit Timin 234 Transmit Timing 228, 234 Transmit Watermark Programming 140 TRDY 28 Twisted Pair Interface Status 98 Twisted Pair Receive Function 98 TX+, TX- 31 TX_CLK 30 TX_EN 31 U USER ACCESSIBLE REGISTERS 101 V VDD 32 VDD_PCI 32 VDDB 32 VDDCO 32 VDDHR 32 VSS 32 VSSB 32 VSSHR 32 W Word I/O Mode 96 X XCLK/XTAL 31 XTAL1 32 XTAL2 32 Am79C978 11