Switches & Pilot DevicesSignaling LightsRelays & SocketsTimersContactorsTerminal BlocksCircuit Breakers
ø30mm - XN E-Stops Switches & Pilot Devices
714 www.IDEC.com 1705151134
30mm XN E-Stops
Key features:
• Plastic bezel, metallic padlock and ush bezel available
• Install up to 20 padlocks (XN4E)
• ø40, ø44 or ø60mm Mushroom heads available
• IDEC’s original “safe break action” ensures that the contacts stay open when the contact
block is detached from the operator.
• Safety-lock mechanism (IEC60947-5-5, 6.2)
• 2-in-1: Push-to-lock, Pull/Turn-to-Reset
• Push-ON LED model allows E-Stops to be illuminated only when latched
• Direct Opening Action mechanism (IEC60947-5-5, 5.2, IEC60947-5-1, Annex K)
• Very short panel depth
• Degree of protection IP65 (IEC60529)
• RoHS compliant (EU directive 2002/95/EC).
• XN4E series complies with OSHA and ISO 12100-2:2003 standards
• UL, c-UL listed, EN compliant
• UL NISD category emergency type device (File# E305148)
File No. E68961
Specications
Applicable Standards IEC60947-5-1, EN60947-5-1, IEC60947-5-5, EN60947-5-5, UL508, UL991, CSA C22.2 No. 14
Operating Temperature Non-illuminated: –25 to +60°C (no freezing), Illuminated: –25 to +55°C (no freezing)
Operating Humidity 45 to 85% RH (no condensation)
Storage Temperature –45 to +80°C
Operating Force
XN1E, XN5E
Push-to-lock: 32N
Pull-to-reset: 21N
Turn-to-reset: 0.27 N·m
XN4E
Push-to-lock: 32N
Pull-to-reset: N/A
Turn-to-reset: 0.4 N·m
Minimum Force Required for Direct Opening Action 80N
Min Operator Stroke Required
for Direct Opening Action 4mm
Maximum Operator Stroke 4.5mm
Contact Resistance 50mΩ maximum (initial value)
Contact Material Gold plated silver
Insulation Resistance 100MΩ minimum (500V DC megger)
Impulse Withstand Voltage 2.5kV
Pollution Degree 3
Operation Frequency 900 operations/hour
Shock Resistance Operating extremes: 150m/s2 (15G), Damage limits: 1000m/s2 (100G)
Vibration Resistance Operating extremes: 10 to 500Hz, amplitude 0.35mm acceleration 50m/s2
Damage limits: 10 to 500Hz, amplitude 0.35mm acceleration 50m/s2
Mechanical Life 250,000 operations minimum
Electrical Life 100,000 operations minimum, (250,000 operations minimum @ 24V AC/DC, 100mA)
Degree of Protection Operator: IP65 (IEC60529)
Terminal: IP20 (when XW9Z-VL2MF is installed)
Terminal Style M3.0 screw terminal
Recommended Tightening Torque for Locking Ring 2.5N·m
Wire Size 16 AWG max
Weight
XN1E: Plastic bezel: 83g (ø40 mm), 93g (ø60 mm)
XN5E: Flush bezel: 89g
XN4E: Padlock type: 20g
Switches & Pilot Devices Signaling Lights Relays & Sockets Timers Contactors Terminal Blocks Circuit Breakers
715
800-262-IDEC (4332) • USA & Canada
ø30mm - XN E-Stops
Switches & Pilot Devices
1705151134
Part Numbers
XN1E Plastic Bezel Type E-Stops (push-pull/twist reset)
Style Operator Type Main Contact Monitor Contact Part Number
Non-Illuminated
40mm Mushroom
1NC 1NO XN1E-BV411MR
2NC – XN1E-BV402MR
2NC 2NO XN1E-BV422MR
3NC 1NO XN1E-BV413MR
4NC – XN1E-BV404MR
60mm Mushroom
1NC 1NO XN1E-BV511MR
2NC – XN1E-BV502MR
2NC 2NO XN1E-BV522MR
3NC 1NO XN1E-BV513MR
4NC – XN1E-BV504MR
Illuminated
40mm Mushroom LED
(24V AC/DC)
1NC 1NO XN1E-LV411Q4MR
2NC – XN1E-LV402Q4MR
2NC 2NO XN1E-LV422Q4MR
3NC 1NO XN1E-LV413Q4MR
4NC – XN1E-LV404Q4MR
40mm Mushroom Push-ON LED
(24V AC/DC) 2NC 1NO XN1E-TV412Q4MR
XN4E Padlock Type E-Stops (push twist reset only)
Style Operator Type Main Contact Monitor Contact Part Number
Non-Illuminated
44mm Mushroom
1NC 1NO XN4E-BL411MR
2NC - XN4E-BL402MR
2NC 2NO XN4E-BL422MR
3NC 1NO XN4E-BL413MR
4NC - XN4E-BL404MR
Illuminated
44mm Mushroom LED
(24V AC/DC)
1NC 1NO XN4E-LL411Q4MR
2NC - XN4E-LL402Q4MR
2NC 2NO XN4E-LL422Q4MR
3NC 1NO XN4E-LL413Q4MR
4NC - XN4E-LL404Q4MR
44mm Mushroom Push-ON LED
(24V AC/DC) 2NC 1NO XN4E-TL412Q4MR
XN5E Flush Bezel Type E-Stops (push-pull/twist reset)
Style Operator Type Main Contact Monitor Contact Part Number
Non-Illuminated
40mm Mushroom
1NC 1NO XN5E-BV411MR
2NC - XN5E-BV402MR
2NC 2NO XN5E-BV422MR
3NC 1NO XN5E-BV413MR
4NC - XN5E-BV404MR
Illuminated
40mm Mushroom LED
(24V AC/DC)
1NC 1NO XN5E-LV411Q4MR
2NC - XN5E-LV402Q4MR
2NC 2NO XN5E-LV422Q4MR
3NC 1NO XN5E-LV413Q4MR
4NC - XN5E-LV404Q4MR
40mm Mushroom Push-ON LED
(24V AC/DC) 2NC 1NO XN5E-TV412Q4MR
Switches & Pilot DevicesSignaling LightsRelays & SocketsTimersContactorsTerminal BlocksCircuit Breakers
ø30mm - XN E-Stops Switches & Pilot Devices
716 www.IDEC.com 1705151134
Contact Ratings
Rated Insulation Voltage (Ui) 250V
Rated Current (Ith) 5A
Rated Operating Voltage (Ue) 30V 125V 250V
Rated Operating Current
Main
Contacts (NC)
AC 50/60Hz Resistive Load (AC-12) – 5A 3A
Inductive Load (AC-15) – 3A 1.5A
DC Resistive Load (DC-12) 2A 0.4A 0.2A
Inductive Load (DC-13) 1A 0.22A 0.1A
Monitor
Contacts (NO)
AC 50/60Hz Resistive Load (AC-12) – 1.2A 0.6A
Inductive Load (AC-14) – 0.6A 0.3A
DC Resistive Load (DC-12) 2A 0.4A 0.2A
Inductive Load (DC-13) 1A 0.22A 0.1A
1. Minimum applicable load: 5V AC/DC, 1mA (reference value).
2. The rated operating currents are measured at resistive/inductive load types specied
in IEC 60947-5-1.
Illuminated Unit LED Ratings
Model Operating Voltage Current
XN 24V AC/DC ±10% 15mA
Depth Behind the Panel
Model Depth (mm) Description
XN1E 47.7 1 - 4 contacts, plastic bezel
XN5E 60.4 1 - 4 contacts, ush bezel
XN4E 61.4 1 - 4 contacts, padlock
Mounting Hole Layout
øA
X
Y
Measurements
Size øA X & Y
XN1E, XN5E 30.5+0.5 70mm min
XN4E 30.5
For XN4E, determine
the values according to
the size and number of
padlocks and hasp.
Panel Cutout
Push-ONIlluminated
3347.7
20.1 18.5
37
33.0+0.5
0
4.8+0.2
0
R0.8 max.
ø30.5
+0.5
0
Panel Cut-out
Panel Thickness 1 to 5
Terminal Cover
XW9Z-VL2M
Rubber Gasket
Locking Ring
M3 Terminal
Screws
ø40
Part Numbers
XN1E - L V 4 02 Q4 MR
Bezel
1: Plastic Bezel
4: Padlock
5: Flush Bezel
Illumination
XN1E, XN5E
BV: Non-Illuminated
LV: Illuminated LED
TV: Illuminated
Push-ON LED
XN4E
BL: Non-Illuminated
LL: Illuminated LED
TL: Illuminated
Push-ON LED
Mushroom Size
4: ø40mm: XN1E, XN5E
ø44mm: XN4E
5: ø60mm
(XN1E non-illuminated only)
Contact Conguration*
11: 1NO - 1NC
02: 2NC
13: 1NO - 3NC
22: 2NO - 2NC
04: 4NC
12: 1NO-2NC (Push-ON
LED only)
Voltage Code
Blank: Non-Illuminated
Q4: 24V AC/DC (Illuminated
& Push-ON LED type)
*Contact IDEC for additional congurations.
Terminal Arrangements (Bottom View)
4NC 1NO-3NC 2NC 1NO-1NC 2NO-2NC 1NO-2NC
Non-Illuminated
TOPTOP
*1 *2
*2*1
*1
*3*4
*2
TOP
*1 *2
*4*3
*1
*3*4
*2
*2
*1 *2
*2*1
*1
*1*2
LRLR
TOP
*1 *2
*2*1
*1
*3*4
*2
LR
LR
TOP
LR
*3 *4
*4 *3
*1 *2
*2 *1
Push-ON
LED
TOP
X1 X2
LR
∗3∗4
∗1∗2
∗2∗1
Illuminated
TOPTOP
X2
*2
LED
*4 *3X1
*1
*1 *2
*2*1
TOP
X2
*2
LED
*4 *3X1
*1
*3 *4
*2*1
*1 *2
*2*1
*1
X1
LED
*2
X2*1*2
LR
TOP
X2
*2
LED
*4 *3X1
*1
*3 *4
*2*1
LRLR
LR
TOP
X2
LED
X1
LR
*3 *4
*4 *3
*1 *2
*2 *1
Terminal Marking Description
• Contact Type
• Contact Number (1-4)
TOP
(Example: 1NO-3NC contact)
LR
11 12
34 33
21 22
42 41
1-2: NC main contact
3-4: NO monitor contact
Starting with the
contact on TOP in a
counterclockwise direction.
Note:
1: contact on the TOP
2: contact on the Left
3: contact on the Bottom
4: contact on the Right
Switches & Pilot Devices Signaling Lights Relays & Sockets Timers Contactors Terminal Blocks Circuit Breakers
717
800-262-IDEC (4332) • USA & Canada
ø30mm - XN E-Stops
Switches & Pilot Devices
1705151134
Dimensions (mm)
XN1E Non-Illuminated (with terminal cover)
Push-ONIlluminated
3347.7
20.1 18.5
37
33.0+0.5
0
4.8+0.2
0
R0.8 max.
ø30.5
+0.5
0
Panel Cut-out
Panel Thickness 1 to 5
Terminal Cover
XW9Z-VL2M
Rubber Gasket
Locking Ring
M3 Terminal
Screws
ø40
XN1E Illuminated/Push-ON (with terminal cover)
Push-ONIlluminated
3347.7
20.1 18.5
37
33.0+0.5
0
4.8+0.2
0
R0.8 max.
ø30.5
+0.5
0
Panel Cut-out
Panel Thickness 1 to 5
Terminal Cover
XW9Z-VL2M
Rubber Gasket
Locking Ring
M3 Terminal
Screws
ø40
XN5E Illuminated (with terminal cover)
Push-ONIlluminated
ø41
2160.4
20.1 18.5
37
Rubber Gasket
Locking Ring
M3 Terminal Screws
ø40
33.0 +0.5
0
0
ø30.5
max.
+0.5
0
Panel Cut-out
Panel Thickness 1 to 5
Terminal Cover
XW9Z-VL2M
XN4E Illuminated (with terminal cover)
61.4
59.9
20.1 18.5
43
37
ø44
33.0+0.5
0
4.8+0.2
0
R0.8 max.
ø30.5
+0.5
0
Panel Cut-out
Panel Thickness 1 to 6
Terminal Cover
XW9Z-VL2M
Rubber Gasket
Locking Ring
M3 Terminal Screws
Push-ONIlluminated
Nameplates
Item Part No. Legend Mounting Panel Thickness
ø60mm
ø30mm
HNAV-0 (blank) XN4E:
1.0 to 4.5 mm
XN1E, XN5E:
1.0 to 3.5 mm
HNAV-27 EMERGENCY
STOP
XN5E Non-Illuminated (with terminal cover)
ø41
2160.4
20.1 18.5
37
ø40
33.0 +0.5
0
4.8+0.2
0
ø30.5
R0.8
max.
+0.5
0
Panel Cut-out
Panel Thickness 1 to 5
Terminal Cover
XW9Z-VL2M
Rubber Gasket
Locking Ring
M3 Terminal Screws
XN4E Non-Illuminated (with terminal cover)
61.4
20.1 18.5
43
ø44
33.0+0.5
0
4.8+0.2
0
R0.8 max.
ø30.5
+0.5
0
Panel Cut-out
Rubber Gasket
Locking Ring
M3 Terminal Screws
Panel Thickness 1 to 6
Terminal Cover
XW9Z-VL2M
Accessories
Item Description Part Number
Locking Ring Wrench XN9Z-T1
Locking Ring Twist Wrench TWST-T1
Lockout Hasp XN9Z-HASP421
Item Description Part Number
Terminal Cover for Contact Block XW9Z-VL2M
IP20 Fingersafe Cover XW9Z-VL2MF
Switches & Pilot DevicesSignaling LightsRelays & SocketsTimersContactorsTerminal BlocksCircuit Breakers
ø30mm - XN E-Stops Switches & Pilot Devices
718 www.IDEC.com 1705151134
Operating Instructions
Removing the Contact Block
➀ Grab
➀ Grab
Latch
Bayonet Ring (yellow)
➁ Pull
➂
Turn counterclockwise
First unlock the operator button. Grab the yellow
bayonet ring j and pull back the bayonet ring
until the latch pin clicks k, then turn the contact
block counterclockwise and pull out l.
Notes for removing the contact block
1. Do not attempt to remove the contact block
while the operator is latched, otherwise the switch may be damaged.
2. When the contact block is removed, the monitor contact (NO contact) is
closed.
3. While removing the contact block, do not use excessive force, otherwise the
switch may be damaged.
4. An LED lamp is built into the contact block for illuminated pushbuttons. When
removing the contact block, pull the contact block straight to prevent damage
to the LED lamp. If excessive force is used, the LED lamp may be damaged
and fail to light.
Panel Mounting
Rubber Gasket
Operator without
thread
TOP Marking
Anti-rotation
Projection
Locking Ring
Remove the locking ring from the operator
and check that the rubber gasket is in place.
Insert the operator from panel front into the
panel hole. Face the side without thread on
the operator with TOP marking upward, and
tighten the locking ring using ring wrench
XN9Z-T1 or TWST-T1 to a torque of
2.5 N·m maximum.
When using a nameplate
Projection
When using a nameplate HNAV-0, break the projection
from the nameplate using pliers.
Installing the Contact Block
▲ Marking
▼ Marking
➀ Push
TOP Marking
➁ T
urn clockwise
First unlock the operator button. Align the
small q marking on the edge of the operator
with the small p marking on the yellow
bayonet ring. Hold the contact block, not the
bayonet ring. Press the contact block onto the
operator and turn the contact block clockwise
until the bayonet ring clicks.
Notes for installing the contact block
1. Do not attempt to install the contact block when the operator is latched,
otherwise the switch may be damaged.
2. Make sure that the bayonet ring is in the locked position.
Installing & Removing Terminal Covers
XW9Z-VL2M
➀
Place the projections
on the contact block.
TOP Markings
➁ Press the
terminal cove
r
Projections Slots
To install the terminal cover, align the TOP
marking on the terminal cover with the
TOP marking on the contact block. Place
the two projections on the bottom side
of the contact block into the slots in the
terminal cover. Press the terminal cover
toward the contact block.
To remove the terminal cover, pull out the
(Pull)
TOP Marking
TOP Marking
Projections
two latches on the top side of the terminal
cover. Do not exert excessive force to the
latches, otherwise the latches may break.
IP20 Fingersafe Terminal
Cover XW9Z-VL2MF
To install the IP20 ngersafe terminal
(Press)
TOP Marking
TOP Marking
cover, align the TOP marking on the cover
with the TOP marking on the contact
block, and press the cover toward
the contact block.
1. Once installed, the XW9Z-VL2MF cannot be removed.
2. With the XW9Z-VL2MF installed, crimping terminals cannot be used.
3. The XW9Z-VL2MF cannot be installed after wiring.
4. Make sure that the XW9Z-VL2MF is securely installed. IP20 cannot be achieved when
installed loosely, and electric shock may occur.
Notes for Operation
When using the XN emergency stop switches in safety-related part of a control
system, observe safety standards and regulations of the relevant country or
region. Also be sure to perform a risk assessment before operation.
Wiring
Tighten the M3 terminal screws to a torque of 0.6 to 1.0 N·m.
Contact Bounce
When the button is reset by pulling or turning, the NC main contacts will bounce.
When pressing the button, the NO monitor contacts will bounce.
When designing a control circuit, take the contact bounce time into consider-
ation (reference value: 20 ms).
LED Illuminated Switches
LED lamp is built into the contact block and cannot be replaced.
Handling
Do not expose the switch to excessive shocks and vibrations, for example by
operating the switch with tools. Otherwise the switch may be deformed or dam-
aged, causing malfunction or operation failure.
Screw Terminal Type
1. AWG18 to 16
2. Tighten the M3 terminal screw to a tightening torque of 0.6 to 1.0 N·m.
Switches & Pilot Devices Signaling Lights Relays & Sockets Timers Contactors Terminal Blocks Circuit Breakers
719
800-262-IDEC (4332) • USA & Canada
ø30mm - XN E-Stops
Switches & Pilot Devices
1705151134
Operating Instructions, continued
Screw Terminal Type
1. Wire thickness: 0.75 to 1.25 mm2 (AWG18 to 16)
Wire
Insulating Tube
Crimping Terminal
4.7 to 5.9
6.0 max.
3.2 min.
4.7 to 5.9
3.0 max.
ø3.2 min.
Wire
Insulating Tube
Crimping
Terminal
4.7 to 5.9
ø6.0 max.
4.7 min. 6.2 max.
ø1.2 max.
Ring Terminal Spade Terminal
Applicable Crimping Terminals Solid Wire
Be sure to install an insulating tube on the crimping terminal.
2. Tighten the M3 terminal screw to a tightening torque of 0.6 to 1.0 N·m.
Connector Type
1. Connector shape
Tyco Electronics, D-2000 series
Part No. 1376009-1 (tab header, board mount)
2. Applicable connectors (to be supplied by user)
Tyco Electronics, D-2000 series
Part No. 1-1318119-4 (receptacle housing)
Tyco Electronics, D-2000 series
Part No. 1318107-1 (receptacle contact)
3. To prepare correct receptacles for the connector type, read the instruction
sheet and catalog of Tyco Electronics and understand the installation and
wiring method.
4. Fasten the cable so that the connector is not pulled.
Otherwise the switch may be deformed and damaged, causing malfunction or
operation failure.
Installing and Removing Terminal Covers
XW9Z-VL2M
To install the terminal cover, align the TOP marking on the terminal cover with
the TOP marking on the contact block. Place the two projections on the bottom
side of the contact block into the slots in the terminal cover. Press the terminal
cover toward the contact block.
k Press the
terminal cover
TOP marking
j Place the projections
on the contact block
To remove the terminal cover, pull out the two latches on the top side of the
terminal cover. Do not exert excessive force to the latches, otherwise the latches
may break.
TOP Markings
Pull out the latches
IP20 Protection Terminal Cover
XW9Z-VL2MF
To install the IP20 protection cover, align the TOP marking on the cover with the
TOP marking on the contact block, and press the cover toward the contact block.
TOP marking
TOP marking
(Press)
1. Once installed, the XW9Z-VL2MF cannot be removed.
2. The XW9Z-VL2MF cannot be installed after wiring.
3. With the XW9Z-VL2MF installed, crimping terminals cannot be used. Use solid wires.
4. Make sure that the XW9Z-VL2MF is securely installed. IP20 cannot be achieved when
installed loosely, and electric shocks may occur.
Contact Bounce
When the button is reset by pulling or turning, the NC main contacts will bounce.
When pressing the button, the NO monitor contacts will bounce.
When designing a control circuit, take the contact bounce time into consider-
ation (reference value: 20 ms).
LED Illuminated Switches
An LED lamp is built into the contact block and cannot be replaced.
Installing the Anti-rotation Ring
HW9Z-RL
Align the side without thread on the operator with TOP marking, the small s
marking on the anti-rotation ring, and the recess on the mounting panel.
TOP marking
p marking on the anti-rotation ring
Without thread
Anti-rotation Ring (HW9Z-RL)