Caution: Observe precautions when handling because these devices are sensitive to electrostatic discharge
WIDE BAND SPDT SWITCH
CMOS INTEGRATED CIRCUIT
PD5713TK
Document No. PU10627EJ01V0DS (1st edition)
Date Published September 2006 NS CP(K)
DESCRIPTION
The
PD5713TK is a CMOS MMIC for wide band SPDT (Single Pole Double Throw) switch which were developed
for mobile communications, wireless communications and another general-purpose RF switching application.
This device can operate frequency from 0.05 to 2.5 GHz, having the low insertion loss and high isolation.
This device is housed in a 6-pin lead-less minimold (1511) package. And this package is able to high-density
surface mounting.
FEATURES
• Supply voltage : VDD = 1.8 to 3.6 V (2.8 V TYP.)
• Switch control voltage : Vcont (H) = 1.8 to 3.6 V (2.8 V TYP.)
: Vcont (L) = 0.2 to +0.4 V (0 V TYP.)
• Low insertion loss : Lins1 = 0.6 dB TYP. @ f = 0.05 to 1.0 GHz, VDD = 2.8 V, Vcont (H) = 2.8 V, Vcont (L) = 0 V
: Lins2 = 0.8 dB TYP. @ f = 1.0 to 2.0 GHz, VDD = 2.8 V, Vcont (H) = 2.8 V, Vcont (L) = 0 V
: Lins3 = 0.95 dB TYP. @ f = 2.0 to 2.5 GHz, VDD = 2.8 V, Vcont (H) = 2.8 V, Vcont (L) = 0 V
• High isolation : ISL1 = 32.5 dB TYP. @ f = 0.05 to 1.0 GHz, VDD = 2.8 V, Vcont (H) = 2.8 V, Vcont (L) = 0 V
: ISL2 = 25 dB TYP. @ f = 1.0 to 2.0 GHz, VDD = 2.8 V, Vcont (H) = 2.8 V, Vcont (L) = 0 V
: ISL3 = 22.5 dB TYP. @ f = 2.0 to 2.5 GHz, VDD = 2.8 V, Vcont (H) = 2.8 V, Vcont (L) = 0 V
• Handling power : Pin (1 dB) = +21.0 dBm TYP. @ f = 1.0 GHz, VDD = 2.8 V, Vcont (H) = 2.8 V, Vcont (L) = 0 V
: Pin (0.1 dB) = +17.0 dBm TYP. @ f = 1.0 GHz, VDD = 2.8 V, Vcont (H) = 2.8 V, Vcont (L) = 0 V
• High-density surface mounting : 6-pin lead-less minimold package (1.5 1.1 0.55 mm)
APPLICATIONS
•Mobile communications
• Wireless communications
• Another general-purpose RF switching applications
ORDERING INFORMATION
Part Number
Order Number
Package
Marking
Supplying Form
PD5713TK-E2
PD5713TK-E2-A
6-pin lead-less minimold
(1511) (Pb-Free)
C3Q
Embossed tape 8 mm wide
Pin 1, 6 face the perforation side of the tape
Qty 5 kpcs/reel
Remark To order evaluation samples, contact your nearby sales office.
Part number for sample order:
PD5713TK-A
PHASE-OUT
Data Sheet PU10627EJ01V0DS
2
PD5713TK
PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM
Pin No.
Pin Name
1
OUTPUT1
2
GND
3
OUTPUT2
4
Vcont
5
INPUT
6
VDD
TRUTH TABLE
Vcont
INPUTOUTPUT1
INPUTOUTPUT2
Low
OFF
ON
High
ON
OFF
ABSOLUTE MAXIMUM RATINGS (TA = +25C, unless otherwise specified)
Parameter
Symbol
Ratings
Unit
Supply Voltage
VDD
0.5 to +4.6
V
Switch Control Voltage
Vcont
0.5 to +4.6
V
Voltage Difference
Vcont (H)
VDD
+0.5
V
Input Power
Pin
+23
dBm
Operating Ambient Temperature
TA
45 to +85
C
Storage Temperature
Tstg
55 to +150
C
RECOMMENDED OPERATING RANGE (TA = +25C, unless otherwise specified)
Parameter
Symbol
MIN.
TYP.
MAX.
Unit
Supply Voltage
VDD
+1.8
+2.8
+3.6
V
Switch Control Voltage (H)
Vcont (H)
+1.8
+2.8
+3.6
V
Switch Control Voltage (L)
Vcont (L)
0.2
0
+0.4
V
Remark VDD 0.4 V Vcont (H) VDD + 0.2 V
PHASE-OUT
Data Sheet PU10627EJ01V0DS
3
PD5713TK
ELECTRICAL CHARACTERISTICS
(TA = +25C, VDD = 2.8 V, Vcont (H) = 2.8 V, Vcont (L) = 0 V, DC cut capacitors = 1 000 pF, unless otherwise
specified)
Parameter
Symbol
Test Conditions
MIN.
TYP.
MAX.
Unit
Insertion Loss 1
Lins1
f = 0.05 to 1.0 GHz
0.6
0.8
dB
Insertion Loss 2
Lins2
f = 1.0 to 2.0 GHz
0.8
1.0
dB
Insertion Loss 3
Lins3
f = 2.0 to 2.5 GHz
0.95
1.2
dB
Isolation 1
ISL1
f = 0.05 to 1.0 GHz
30
32.5
dB
Isolation 2
ISL2
f = 1.0 to 2.0 GHz
22
25
dB
Isolation 3
ISL3
f = 2.0 to 2.5 GHz
20
22.5
dB
Input Return Loss
RLin
f = 0.05 to 2.5 GHz
13
17
dB
Output Return Loss
RLout
f = 0.05 to 2.5 GHz
13
17
dB
0.1 dB Loss Compression
Pin (0.1 dB)
f = 1.0 GHz
+13.0
+17.0
dBm
Input Power Note 1
1 dB Loss Compression
Pin (1 dB)
f = 1.0 GHz
+21.0
dBm
Input Power Note 2
Supply Current
IDD
VDD = Vcont = 2.8 V, RF off
0.01
1.0
A
Switch Control Current
Icont
VDD = Vcont = 2.8 V, RF off
0.01
1.0
A
Switch Control Speed
tSW
f = 1.0 GHz
30
100
ns
Notes 1. Pin (0.1 dB) is measured the input power level when the insertion loss increases more 0.1 dB than that of
linear range.
2. Pin (1 dB) is measured the input power level when the insertion loss increases more 1 dB than that of linear
range.
Caution This device is used it is necessary to use DC cut capacitors.
The value of DC cut capacitors should be chosen to accommodate the frequency of operation,
bandwidth, switching speed and the condition with actual board of your system.
PHASE-OUT
Data Sheet PU10627EJ01V0DS
4
PD5713TK
EVALUATION CIRCUIT
Remark C0 = 1 000 pF
Caution This IC has pull down resistance between RF line and GND, witch fixes electric potential of RF
line to 0 V, then the IC cannot be used for DC switching.
The application circuits and their parameters are for reference only and are not intended for use in actual design-ins.
PHASE-OUT
Data Sheet PU10627EJ01V0DS
5
PD5713TK
ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD
USING THE EVALUATION BOARD
Symbol
Values
C1, C2, C3
1 000 pF
C4, C5
1 000 pF
PHASE-OUT
Data Sheet PU10627EJ01V0DS
6
PD5713TK
TYPICAL CHARACTERISTICS
(TA = +25C, VDD = 2.8 V, Vcont (H) = 2.8 V, Vcont (L) = 0 V, Pin = 0 dBm, DC cut capacitors = 1 000 pF,
unless otherwise specified)
Remark The graphs indicate nominal characteristics.
PHASE-OUT
Data Sheet PU10627EJ01V0DS
7
PD5713TK
Remark The graphs indicate nominal characteristics.
PHASE-OUT
Data Sheet PU10627EJ01V0DS
8
PD5713TK
MOUNTING PAD DIMENSIONS
6-PIN LEAD-LESS MINIMOLD (1511) (UNIT: mm)
Remark The mounting pad layouts in this document are for reference only.
PHASE-OUT
Data Sheet PU10627EJ01V0DS
9
PD5713TK
PACKAGE DIMENSIONS
6-PIN LEAD-LESS MINIMOLD (1511) (UNIT: mm)
PHASE-OUT
10 Data Sheet PU10627EJ01V0DS
PD5713TK
RECOMMENDED SOLDERING CONDITIONS
This product should be soldered and mounted under the following recommended conditions. For soldering
methods and conditions other than those recommended below, contact your nearby sales office.
Soldering Method
Soldering Conditions
Condition Symbol
Infrared Reflow
Peak temperature (package surface temperature) : 260C or below
Time at peak temperature : 10 seconds or less
Time at temperature of 220C or higher : 60 seconds or less
Preheating time at 120 to 180C : 12030 seconds
Maximum number of reflow processes : 3 times
Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below
IR260
Wave Soldering
Peak temperature (molten solder temperature) : 260C or below
Time at peak temperature : 10 seconds or less
Preheating temperature (package surface temperature) : 120C or below
Maximum number of flow processes : 1 time
Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below
WS260
Partial Heating
Peak temperature (terminal temperature) : 350C or below
Soldering time (per side of device) : 3 seconds or less
Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below
HS350
Caution Do not use different soldering methods together (except for partial heating).
PHASE-OUT
NOTICE
1. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and
application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. California
Eastern Laboratories and Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits,
software, or information.
2. California Eastern Laboratories has used reasonable care in preparing the information included in this document, but California Eastern Laboratories does
not warrant that such information is error free. California Eastern Laboratories and Renesas Electronics assumes no liability whatsoever for any damages
incurred by you resulting from errors in or omissions from the information included herein.
3. California Eastern Laboratories and Renesas Electronics do not assume any liability for infringement of patents, copyrights, or other intellectual property
rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document. No license, express,
implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of California Eastern Laboratories or Renesas
Electronics or others.
4. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. California Eastern
Laboratories and Renesas Electronics assume no responsibility for any losses incurred by you or third parties arising from such alteration, modication, copy
or otherwise misappropriation of Renesas Electronics product.
5. Renesas Electronics products are classied according to the following two quality grades: “Standard” and “High Quality”. The recommended applications
for each Renesas Electronics product depends on the product’s quality grade, as indicated below. “Standard”: Computers; ofce equipment; communications
equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and
industrial robots etc. “High Quality”: Transportation equipment (automobiles, trains, ships, etc.); trafc control systems; anti-disaster systems; anti-crime
systems; and safety equipment etc. Renesas Electronics products are neither intended nor authorized for use in products or systems that may pose a direct
threat to human life or bodily injury (articial life support devices or systems, surgical implantations etc.), or may cause serious property damages (nuclear
reactor control systems, military equipment etc.). You must check the quality grade of each Renesas Electronics product before using it in a particular
application. You may not use any Renesas Electronics product for any application for which it is not intended. California Eastern Laboratories and Renesas
Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product
for which the product is not intended by California Eastern Laboratories or Renesas Electronics.
6. You should use the Renesas Electronics products described in this document within the range specied by California Eastern Laboratories, especially with
respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product
characteristics. California Eastern Laboratories shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products
beyond such specied ranges.
7. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specic characteristics such as
the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation
resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by
re in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy,
re control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of
microcomputer software alone is very difcult, please evaluate the safety of the nal products or systems manufactured by you.
8. Please contact a California Eastern Laboratories sales ofce for details as to environmental matters such as the environmental compatibility of each Renesas
Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of
controlled substances, including without limitation, the EU RoHS Directive. California Eastern Laboratories and Renesas Electronics assume no liability for
damages or losses occurring as a result of your noncompliance with applicable laws and regulations.
9. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited
under any applicable domestic or foreign laws or regulations. You should not use Renesas Electronics products or technology described in this document
for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. When
exporting the Renesas Electronics products or technology described in this document, you should comply with the applicable export control laws and
regulations and follow the procedures required by such laws and regulations.
10. It is the responsibility of the buyer or distributor of California Eastern Laboratories, who distributes, disposes of, or otherwise places the Renesas Electronics
product with a third party, to notify such third party in advance of the contents and conditions set forth in this document, California Eastern Laboratories and
Renesas Electronics assume no responsibility for any losses incurred by you or third parties as a result of unauthorized use of Renesas Electronics products.
11. This document may not be reproduced or duplicated in any form, in whole or in part, without prior written consent of California Eastern Laboratories.
12. Please contact a California Eastern Laboratories sales ofce if you have any questions regarding the information contained in this document or Renesas
Electronics products, or if you have any other inquiries.
NOTE 1: “Renesas Electronics” as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries.
NOTE 2: “Renesas Electronics product(s)” means any product developed or manufactured by or for Renesas Electronics.
NOTE 3: Products and product information are subject to change without notice.
CEL Headquarters • 4590 Patrick Henry Drive, Santa Clara, CA 95054 • Phone (408) 919-2500 • www.cel.com
For a complete list of sales ofces, representatives and distributors,
Please visit our website: www.cel.com/contactus
PHASE-OUT
Possible Replacement: CG2214M6