SPEC,NO.MES-DG60B037 SPECIFICATIONS FOR MANUAL INSERTION MAGNETIC CARD READER nh ZzuU- 1. &g& FT OMA 42 T 4 SEP. 1997 MATUSHITA ELECTRIC INDUSTRIAL CO.,LTD. MATUSHITA INDUSTRIAL EQUIPMENT CO.,LTD. OSAKA JAPAN if 1d H 62:87 (H) BCCHB0HLE, cov7na = QEZ RERHLEMBBEB IS ulae /ed 10. ll. 12. CONTENTS . INTRODUCTION 9 --- rrr rrr rrr rrr rrr tt terre COMPOSITION 0 --e ewe eec cece eece erent tec eee ceeeeeee . SPECIFICATION ----++----- 7-70 => eee ee eee eee eee eee . TERMINAL NO. OF CONNECTOR 9 ---eee- eee cree eee eee . INTERFACE REQUIREMENTS 90 --o re eeee nner eeee eee - NOTES FOR BETTER OPERATION -------- Lotte tle . APPEARANCE oo rrr ttre rrr rete rrr rte tee errr ene . CONNECTOR DIMENSION 9 --eee--en enone eee eee eee . MAGNETIC CARD SPECIFICATION = --rrrrter rr rrreece LIFE OF PARTS rococo etter rere entree ec eee MAINTENANCE METHOD 90 --ovrteteeccerce eter cee CAUTIONS ON THE USE) 0 were eee erent eee GZ CESRHLEMRR EBL EE 214 4H 0:8T () B2CHB0RLE,1. INTRODUCTION This specification applies to the Panasonic magnetic card reader, featuring small size, light weight and high performance. 2. COMPOSITION The magnetic card reader is composed of the mechanical portion, single circuit for read. 1) Mechanical portion The mechanical portion is mainly composed of the following parts. 1. Body (Color: Transparence) 2. Card entrance slot (Color: Black), 3. Magnetic head (Core material: Permalloy) 2) Circuit portion 1. Read amplifier circuit for 2 tracks 3. SPECIFICATION 3.1 CARD STANDARD Refer to Magnetic Card Specification (9). 3.2 FUNCTION (1) Read/Write : Read only (2) Read timing : Ejection (3) Compatibility : Cards and installation (4) Installation of : Horizontal direction the transport una ae co/end GES RESRHLERRR EEL J1d K 90:81 ) ACTHS0HLE.3.3 BASIC PERFORMANCE (1) Performance ZU-1870MA4T# ISO 7811 Card standard [S01 IS02 Track used Track lst Track 2nd Recording method FM FM Recording | 210 BPI 75 BPI density piu P-Sietoas' | Goi esaes (2) Card operation speed : 10~ 100 cm/sec. (3) Magnetic head Channel 7 2 Channel width : 1.4mm (4) Insulation resistance : More than 1OMQ at DC 250 V (MeAsiired between P.C.B. ground terminal and frame) 3.4 ENVIRONMENT REQUIREMENTS (1) Temperature range : -20~ 60C (Operation) (2) Temperature range : -30~ 70C (Conservation) (3) Humidity range : 1O0~ 90%RH (Operation) (No condensation allowed) (4) Humidity range : 10~ 90%RH (Conservation) (No condensation allowed) (5) Vibration : Vibration sweep 10~ 50 Hz/mm X,Y,Z directions (6) Shock durability : 30G 2 aR /CNd GES GHERHLEMRHEA IG SH 1d 4H 1e:9T H) BCCHE0HLE.3.5 PHYSICAL CHARACTERISTICS (1) Dimension : 90 (W) x 119.5 (D) x 46 (H) Unit: mm (2) Weight : Approx. 100 ~ (3) Power supply : 5VDC + 10% Less than 25mA (4) Ripple : Within 50 mVp-p (5) Operating place : Indoor 3.6 ERROR RATE (at indoor conditions by continuous running)) (1) Error : Less than 0.5% * Condition ---::-:> In a clean office room. In damp or dusty atmosphere, the life may be 1/3 to 1/5 of the above figure. 4. TERMINAL NO. OF CONNECTOR 4.1 OUTPUT SIGNAL Connector| Signal | Connecto Signal Pin No. name Pin No. name 1 +5 V 5 RCL2 2 RDT1 6 CLD 3 RCL1 7 GND 4 RDT2 Connector: BS7P-SHF-14A JST 5. INTERFACE REQUIREMENTS 5.1 OUTPUT VOLTAGE | Min (V) | Max (V)| Conditions H level "0 4.0 Vec Tex = -1.0 mA L level "1* - 0.4 Tot = 4.0 mA Qe /90d GES GESRHLEWRAERIG SE J1d M Te:9T (H) BCCHEORLE,5.2 OUTPUT SIGNALS The following paragraphs describe the requirements and interface signals between the user terminal and the Magnetic Card Reader shown in Figure 1. The general timing sequence for entering data from the Magnetic Card Reader to the user terminal is shown in Figure 2. RCL1,2 Magnetic RDT1, 2 User's Card Reader ~ Ferminal GND +5V DC Figure 1 (1) CLD (CARD LOAD) The CLD line will be High when a Magnetic Card is inserted in the end of Magnetic Card Reader. The CLD line will be Low at all other times. (2) RCL1,2 (READ CLOCK) This is used to sample the data line by it's falling edges. The time relationship of the clock with respect to the other signals is shown in Figure 2. User's Terminal starts to carry out sampling of the read data by the falling edge of the signal.In case of performing sampling other than the falling edge sampling method (such as detecting L of RCL by means of polling)to read RDT .check RCL width if it is appropriate. (3) RDT1,2 (READ DATA) At the moment RCL change from High to Low; RDT is "1" when the RDT line is Low. and RDT is "0 when the RDT line is High. se/L0d GES GLERRCERSR ELE Se J1d 4H 18:87 (H) ACCHE0HLE,3.3 TIMING CHART Time of insertion Tima of ejection The magnetic head output ~i Qo - xn oO pa ~ o ot Detail Chart The magnetic head output a R ~ tt Pf ; (ttt te te | ts ROT 1 ' mur Bit data 0 9 ryr 9 9 75 BP| 210 BPI | tg 9.5ys 3.8us e4/19.0us 7.7us Figure 2 Timing Sequence (Typical value) When the jitter of the magnetic head output is 0%.the following equation is satisfied. T=T1=Ta=T2, tiste 2.54 inch 1 Note : T (sec) = = en/ ; x Recording density (BPI) Card speed (cm/sec) 6. NOTES FOR BETTER OPERATION (1) The card should be inserted in the specified direction. (2) Cards which meet standards should be used. (3) Cards should not be dirty, scratched or deformed. ge/gis EZ WHESSRTEWRHERLG 28 J1d 4M 7e:8T (H) BCCHB0HLE.7 APPEARANCE 425 QO 37 119.554 77 | it hil Hote N | | | 3.1201 { Attacnment Hole | qd ) = N i} N Body 1 (Transparence! | 5 Body 2 crransperence) General Tolerance:s0.5 (unit mm) RESSRLEWRHEALG SH ; O3.1x. 4 Attachment 4 hmil a wy +: S pk ~ 1 9 Connector 49. BS7P-SHF-1AA 5 < 228 | usn 46 g8/B0d eas J1d R 7e: RT (H) BUCHbOSLE,ge /0Td 8. CONNECTOR DIMENSION Housing (H7P-SHF-AA) /o 6.0 POST (BS7P-SHF-1AA) o o I @mae@esdse = cco --g-| 1 2.5/1. o.6 5.5 15.0 (Japan Solderless Terminal MFG CO.,LTD.) 94 GES GESHRLEMEREZIG SE 1d ce:st HW) BCCHESLE.9. MAGNETIC CARD SPECIFICATION 9.1 CARD SPECIFICATION 85.47 ~85. 72 6.93 min. ws; | 66 4 8.46~_ 8.97 11. 76~12, 27 12,01~12.52 15. 92 ~15. 82 7,4440.51 (Track 1 or 2 ) 7.44241.0 (Track 3) 53.92~54. 03 (unit:mm) (1) Thickness : 0.76 + 0.08 (2) Transformation : 2 mm max. (3) Impermeabill{ty rate : More than 2.0 (Measured by light permeance desitometer) 9.2 MAGNETIC CHARACTERISTICS (1) Coercive force (He) : 24% 10 A/m (300 Oe+ 12%) (2) Residual flux ( r) : j.25 + 0.15 maxwell/em (3) Squareness ratio : More than 0.70 (dr/ a) 8 g8/1td XS GEERHLEMRGEZLG SH 314 & 7:9 (h) BUCHBORLE, foo/2 10. LIFE OF PARTS Magnetic head : 300,000 passes *Condition ------- In a clean office room. In damp or dusty atmosphere, the life may be 1/3 to 1/5 of the above figure. 11. MAINTENANCE METHOD When replacing parts, exchange the card reader unit. 12.CAUTIONS ON THE USE Please be noted that we do not guarantee proper performance of the card reader if it is used other than the indicated specification range. fe. - 12.1 At the installation (1) Do not drop or bump anything against a card reader. Otherwise, failure may be the result. (2) Do not touch the P.C.B. with bear hands. (3) Be sure to install on a flat surface so as to prevent any force to be applied to the card reader at the installation. (4) Installation of a card guide plate at the both (front and back) sides of the card running part may reinforce stability. (5) The card reader should avoid installation of the following environment. Watery, humid or dusty place. , Near machines which generate magnetic field or inducted noise. (printer. LED display, CRT etc.) Place which gets direct sunlight. 12.2 At the use (1) Be sure to use a card which conforms ISO standard. Anti-magnetic of the applied card should be 2.4 10*~ 2.4.x 105A/m(300 ~ 3000(0e)) of ISO standard. GESHGLEWMR GEIL G SE J1d H 98:81 H) BCCHEOHLE, ou sevttd BE(2) Pulse width of the period L of RCL is about 7.7u S for the card conformable to ISO1 (210 Bpi specification),and about 19x S in case of IS02(75 Bpi specification).If sampling method other than falling edge sampling(such as a method detecting L of RCL by means of polling ) is used, please check with us since data may not be read depending on polling freqency at the host side. * (3) Card operation speed should be within the specification range. Forced stop or change of speed during the card operation may cause a read error. Appropriate speed to maintain stable operation is 30~ 60 cn/sec. (4) Store the card with caution to prevent dirt, scratch and distortion. Especially no foreign matter shall be.stuck on the magnetic stripe surface. Use of such card may result in a read error. (5) Insert a cleaning card and clean the head periodically to prevent wearing of the magnetic head. Head cleaning using the cleaning card should be performed about once a week if the room is not dusty. (6) Depends on installation environment (incorporation condition) or operation condition, external noise or electrostatic and so on may affect the machine, and which may cause an error or a wrong operation. Check the level of noise resistance and electrostatic resistance of your factory before using - the card reader. 10 ge/etd GES GESRHLERSHEELY 5% J1d 4M 98:91 () BCCHBOHLE,