DS3181/DS3182/DS3183/DS3184 Single/Dual/Triple/Quad ATM/Packet PHYs with Built-In LIU www.maxim-ic.com The DS3181, DS3182, DS3183, and DS3184 (DS318x) integrate ATM cell/HDLC packet processor(s) with a DS3/E3 framer(s) and LIU(s) to map/demap ATM cells or packets into as many as four DS3/E3 physical copper lines with DS3-framed, E3-framed, or clear-channel data streams on per-port basis. DS3/E3/STS-1 PORTS APPLICATIONS Access Concentrators SONET/SDH ADM SONET/SDH Muxes PBXs Digital Cross Connect Test Equipment Routers and Switches Integrated Access Device (IAD) Multiservice Access Platform (MSAP) DS3181 DS3181N DS3182 DS3182N DS3183 DS3183N DS3184 DS3184N POS-PHY OR UTOPIA DS318x Multiservice Protocol Platform (MSPP) ATM and Frame Relay Equipment FEATURES Single (DS3181), Dual (DS3182), Triple (DS3183), or Quad (DS3184) with Integrated LIU ATM/Packet PHYs for DS3, E3, and ClearChannel 52Mbps (CC52) PDH Multiplexer/ Demultiplexer ORDERING INFORMATION PART CELL/ DS3/E3 PACKET FRAMER/ FORMATTER PROCESSOR SYSTEM INTERFACE FUNCTIONAL DIAGRAM DS3/E3/STS-1 LIU GENERAL DESCRIPTION TEMP RANGE 0C to +70C -40C to +85C 0C to +70C -40C to +85C 0C to +70C -40C to +85C 0C to +70C -40C to +85C Pin Compatible for Ease of Port Density Migration in the Same PC Board Platform PIN-PACKAGE Each Port Independently Configurable 400 TE-PBGA (27mm x 27mm, 1.27mm pitch) 400 TE-PBGA (27mm x 27mm, 1.27mm pitch) 400 TE-PBGA (27mm x 27mm, 1.27mm pitch) 400 TE-PBGA (27mm x 27mm, 1.27mm pitch) 400 TE-PBGA (27mm x 27mm, 1.27mm pitch) 400 TE-PBGA (27mm x 27mm, 1.27mm pitch) 400 TE-PBGA (27mm x 27mm, 1.27mm pitch) 400 TE-PBGA (27mm x 27mm, 1.27mm pitch) Perform Receive Clock/Data Recovery and Transmit Waveshaping Jitter Attenuator can be Placed Either in the Receive or Transmit Paths Interfaces to 75 Coaxial Cable at Lengths Up to 380 Meters or 1246 Feet (DS3) or 440 Meters or 1443 Feet (E3) Uses 1:2 Transformers on Both Tx and Rx Universal PHYs Map ATM Cells and/or HDLC Packets into DS3 or E3 Data Streams UTOPIA L2/L3 or POS-PHYTM L2/L3 or SPI-3 Interface with 8-, 16-, or 32-Bit Bus Width 66MHz UTOPIA L3 and POS-PHY L3 Clock Note: Add the "+" suffix for the lead-free package option. 52MHz UTOPIA L2 and POS-PHY L2 Clock POS-PHY and POS-PHY Level 3 are trademarks of PMC-Sierra, Inc. Ports Independently Configurable for Cell or Packet Traffic in POS-PHY Bus Modes Direct, PLCP, DSS, and Clear-Channel Cell Mapping Note: Some revisions of this device may incorporate deviations from published specifications known as errata. Multiple revisions of any device may be simultaneously available through various sales channels. For information about device errata, click here: www.maxim-ic.com/errata. 1 REV: 102406 DS3181/DS3182/DS3183/DS3184 FEATURES (continued) Direct and Clear-Channel Packet Mapping Loopbacks Include Line, Diagnostic, Framer, Payload, Analog, and System Interface with Capabilities to Insert AIS in the Directions Away from Loopback Directions On-Chip DS3 (M23 or C-Bit) and E3 (G.751 or G.832) Framer(s) Ports Independently Configurable for DS3, E3 (Full or Subrate) or Arbitrary Framing Protocols Up to 52Mbps Ports can be Disabled to Reduce Power Integrated Clock Rate Adapter to Generate the Remaining Internally Required 44.736MHz (DS3), 34.368MHz (E3), and 52MHz (Arbitrary Framing at Up to 52Mbps) from a Single Clock Reference Source at One of Those Three Frequencies Programmable (Externally Controlled or Internally Finite State Machine Controlled) Subrate DS3/E3 Full-Featured DS3/E3/PLCP Alarm Generation and Detection Pin Compatible with the DS3171/2/3/4 Family and the DS3161/2/3/4 Family Built-In HDLC Controllers with 256-Byte FIFOs for Insertion/Extraction of DS3 PMDL, G.751 Sn Bit, and G.832 NR/GC Bytes and PLCP NR/GC Bytes 8/16-Bit Generic Microprocessor Interface Low-Power (2.7W typ) 3.3V Operation (5VTolerant I/O) On-Chip BERTs for PRBS and Repetitive Pattern Generation, Detection, and Analysis Small, High-Density, Thermally Enhanced, BGA Packaging (TE-PBGA) with 1.27mm Pin Pitch Large Performance-Monitoring Counters for Accumulation Intervals of at Least 1 Second Industrial Temperature Operation: -40C to +85C Flexible Overhead Insertion/Extraction Ports for DS3, E3, and PLCP Framers IEEE1149.1 JTAG Test Port DETAILED DESCRIPTION The DS3181 (single), DS3182 (dual), DS3183 (triple), and DS3184 (quad) PHYs perform all the functions necessary for mapping/demapping ATM cells and/or packets into as many as four DS3 (44.736Mbps) framed, E3 (34.368Mbps) framed, or 52Mbps clear-channel data streams on DS3, E3, or STS-1 physical copper lines. Each line interface unit (LIU) has independent receive and transmit paths. The receiver LIU block performs clock and data recovery from a B3ZS- or HDB3-coded AMI signal and monitors for loss of the incoming signal or can be bypassed for direct clock and data inputs. The receiver LIU block optionally performs B3ZS/HDB3 decoding. The transmitter LIU drives standard pulse-shape waveforms onto 75 coaxial cable or can be bypassed for direct clock and data outputs. The jitter attenuator can be placed in either transmit or receive data path when the LIU is enabled. Dedicated cell processor and packet processor blocks prepare outgoing cells or packets for transmission and check incoming cells or packets upon arrival. Built-in DS3/E3 framers transmit and receive cell/packet data in properly formatted M23 DS3, C-bit DS3, G.751 E3, or G.832 E3 data streams. PLCP framers provide legacy ATM transmission-convergence support. DSS scrambling is performed for clear-channel ATM cell support. With integrated hardware support for both cells and packets, the DS318x DS3/E3 ATM/Packet PHYs provide system onchip solutions (from DS3/E3/STS-1 physical copper lines to ATM/Packet UTOPIA/POS-PHY Level 2/3 system switch) for universal high-density line cards in the unchannelized DS3/E3/clear-channel DS3 ATM/Packet applications. Unused functions can be powered down to reduce device power. The DS318x ATM/Packet PHYs with embedded LIU conform to the telecommunications standards listed in Section 4. 2 DS3181/DS3182/DS3183/DS3184 TABLE OF CONTENTS 1 BLOCK DIAGRAMS 14 2 APPLICATIONS 15 3 FEATURE DETAILS 17 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18 3.19 3.20 3.21 3.22 3.23 3.24 3.25 GLOBAL FEATURES .......................................................................................................................17 RECEIVE DS3/E3/STS-1 LIU FEATURES .......................................................................................17 RECEIVE DS3/E3 FRAMER FEATURES ...........................................................................................17 RECEIVE PLCP FRAMER FEATURES ..............................................................................................18 RECEIVE CELL PROCESSOR FEATURES .........................................................................................18 RECEIVE PACKET PROCESSOR FEATURES .....................................................................................18 RECEIVE FIFO FEATURES .............................................................................................................19 RECEIVE SYSTEM INTERFACE FEATURES .......................................................................................19 TRANSMIT SYSTEM INTERFACE FEATURES .....................................................................................19 TRANSMIT FIFO FEATURES ...........................................................................................................19 TRANSMIT CELL PROCESSOR FEATURES .......................................................................................19 TRANSMIT PACKET PROCESSOR FEATURES ...................................................................................19 TRANSMIT PLCP FORMATTER FEATURES ......................................................................................20 TRANSMIT DS3/E3 FORMATTER FEATURES ...................................................................................20 TRANSMIT DS3/E3/STS-1 LIU FEATURES .....................................................................................20 JITTER ATTENUATOR FEATURES ....................................................................................................20 CLOCK RATE ADAPTER FEATURES.................................................................................................20 HDLC OVERHEAD CONTROLLER FEATURES ..................................................................................20 FEAC CONTROLLER FEATURES ....................................................................................................21 TRAIL TRACE BUFFER FEATURES...................................................................................................21 BIT ERROR RATE TESTER (BERT) FEATURES ................................................................................21 LOOPBACK FEATURES ...................................................................................................................21 MICROPROCESSOR INTERFACE FEATURES .....................................................................................21 SUBRATE FEATURES (FRACTIONAL DS3/E3)..................................................................................21 TEST FEATURES............................................................................................................................22 4 STANDARDS COMPLIANCE 23 5 ACRONYMS AND GLOSSARY 25 6 MAJOR OPERATIONAL MODES 26 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 6.10 7 MAJOR LINE INTERFACE OPERATING MODES 7.1 7.2 7.3 7.4 8 DS3/E3 ATM/PACKET MODE ........................................................................................................26 DS3/E3 ATM/PACKET--OHM MODE ............................................................................................27 DS3/E3 INTERNAL FRACTIONAL (SUBRATE) ATM/PACKET MODE ...................................................28 DS3/E3 EXTERNAL FRACTIONAL (SUBRATE) ATM/PACKET MODE ..................................................29 DS3/E3 FLEXIBLE EXTERNAL FRACTIONAL (SUBRATE) MODE CONFIGURATION MODE ....................30 DS3/E3 G.751 PLCP ATM MODE ................................................................................................31 DS3/E3 G.751 PLCP ATM--OHM MODE ....................................................................................32 CLEAR-CHANNEL ATM/PACKET MODE...........................................................................................34 CLEAR-CHANNEL ATM/PACKET--OHM MODE ..............................................................................35 CLEAR-CHANNEL OCTET ALIGNED ATM/PACKET--OHM MODE .....................................................36 37 DS3HDB3/B3ZS/AMI LIU MODE .................................................................................................37 HDB3/B3ZS/AMI NON-LIU LINE INTERFACE MODE .......................................................................39 UNI LINE INTERFACE MODE ..........................................................................................................40 UNI LINE INTERFACE--OHM MODE ..............................................................................................41 PIN DESCRIPTIONS 42 3 DS3181/DS3182/DS3183/DS3184 8.1 8.2 8.3 SHORT PIN DESCRIPTIONS ............................................................................................................42 DETAILED PIN DESCRIPTIONS ........................................................................................................48 PIN FUNCTIONAL TIMING................................................................................................................66 8.3.1 8.3.2 8.3.3 8.3.4 8.3.5 8.3.6 8.3.7 9 Line IO.................................................................................................................................................. 66 DS3/E3 Framing and PLCP Overhead Functional Timing................................................................... 69 Internal (IFRAC) and External (XFRAC) Fractional DS3/E3 Overhead Functional Timing ................. 72 Flexible Fractional (FFRAC) DS3/E3 Overhead Interface Functinal Timing ....................................... 73 UTOPIA/POS-PHY/SPI-3 System Interface Functional Timing........................................................... 75 Microprocessor Interface Functional Timing ........................................................................................ 87 JTAG Functional Timing....................................................................................................................... 91 INITIALIZATION AND CONFIGURATION 9.1 92 MONITORING AND DEBUGGING ......................................................................................................94 9.1.1 9.1.2 9.1.3 Cell/Packet FIFO.................................................................................................................................. 94 Cell Processor...................................................................................................................................... 94 Packet Processor ................................................................................................................................. 95 10 FUNCTIONAL DESCRIPTION 96 10.1 PROCESSOR BUS INTERFACE ........................................................................................................96 10.1.1 10.1.2 10.1.3 10.1.4 10.1.5 10.1.6 10.1.7 10.1.8 8/16-Bit Bus Widths.............................................................................................................................. 96 Ready Signal (RDY) ............................................................................................................................. 96 Byte Swap Modes ................................................................................................................................ 96 Read-Write/Data Strobe Modes........................................................................................................... 96 Clear on Read/Clear on Write Modes .................................................................................................. 96 Global Write Method ............................................................................................................................ 97 Interrupt and Pin Modes....................................................................................................................... 97 Interrupt Structure ................................................................................................................................ 97 10.2 CLOCKS ........................................................................................................................................99 10.2.1 10.2.2 10.2.3 10.2.4 10.2.5 Line Clock Modes................................................................................................................................. 99 Sources of Clock Output Pin Signals ................................................................................................. 100 Line IO Pin Timing Source Selection ................................................................................................. 103 Clock Structures On Signal IO Pins ................................................................................................... 105 Gapped Clocks................................................................................................................................... 106 10.3 RESET AND POWER-DOWN ..........................................................................................................107 10.4 GLOBAL RESOURCES ..................................................................................................................109 10.4.1 10.4.2 10.4.3 10.4.4 10.4.5 10.4.6 Clock Rate Adapter (CLAD)............................................................................................................... 109 8 kHz Reference Generation ............................................................................................................. 111 One-Second Reference Generation .................................................................................................. 113 General-Purpose IO Pins ................................................................................................................... 113 Performance Monitor Counter Update Details ................................................................................... 114 Transmit Manual Error Insertion ........................................................................................................ 115 10.5 PER-PORT RESOURCES ..............................................................................................................116 10.5.1 Loopbacks.......................................................................................................................................... 116 10.5.2 Loss Of Signal Propagation ............................................................................................................... 118 10.5.3 AIS Logic............................................................................................................................................ 118 10.5.4 Loop Timing Mode ............................................................................................................................. 121 10.5.5 HDLC Overhead Controller ................................................................................................................ 121 10.5.6 Trail Trace .......................................................................................................................................... 121 10.5.7 BERT.................................................................................................................................................. 121 10.5.8 Fractional Payload Controller............................................................................................................. 122 10.5.9 PLCP/Fractional port pins .................................................................................................................. 122 10.5.10 Framing Modes .................................................................................................................................. 127 10.5.11 Mapping Modes.................................................................................................................................. 128 10.5.12 Line Interface Modes.......................................................................................................................... 132 10.6 UTOPIA/POS-PHY/SPI-3 SYSTEM INTERFACE ...........................................................................134 10.6.1 General Description ........................................................................................................................... 134 10.6.2 Features ............................................................................................................................................. 134 10.6.6 System Interface Bus Controller ........................................................................................................ 135 4 DS3181/DS3182/DS3183/DS3184 10.7 ATM CELL/HDLC PACKET PROCESSING .....................................................................................139 10.7.1 10.7.2 10.7.3 10.7.4 10.7.5 10.7.6 10.7.7 10.7.8 General Description ........................................................................................................................... 139 Features ............................................................................................................................................. 139 Transmit Cell/Packet Processor......................................................................................................... 140 Receive Cell/Packet Processor.......................................................................................................... 141 Cell Processor.................................................................................................................................... 141 Packet Processor ............................................................................................................................... 146 FIFO ................................................................................................................................................... 148 System Loopback............................................................................................................................... 149 10.8 DS3/E3 PLCP FRAMER ..............................................................................................................150 10.8.1 10.8.2 10.8.3 10.8.4 10.8.5 10.8.6 10.8.7 10.8.8 General Description ........................................................................................................................... 150 Features ............................................................................................................................................. 150 Transmit PLCP Frame Processor ...................................................................................................... 151 Receive PLCP Frame Processor ....................................................................................................... 151 Transmit DS3 PLCP Frame Processor .............................................................................................. 151 Receive DS3 PLCP Frame Processor ............................................................................................... 154 Transmit E3 PLCP Frame Processor................................................................................................. 155 Receive E3 PLCP Frame Processor.................................................................................................. 158 10.9 FRACTIONAL PAYLOAD CONTROLLER ...........................................................................................160 10.9.1 10.9.2 10.9.3 10.9.4 10.9.5 10.9.6 General Description ........................................................................................................................... 160 Features ............................................................................................................................................. 160 Transmit Fractional Interface ............................................................................................................. 161 Transmit Fractional Controller............................................................................................................ 161 Receive Fractional Interface .............................................................................................................. 161 Receive Fractional Controller............................................................................................................. 161 10.10 DS3/E3 FRAMER/FORMATTER ....................................................................................................163 10.10.1 General Description ........................................................................................................................... 163 10.10.2 Features ............................................................................................................................................. 163 10.10.3 Transmit Formatter............................................................................................................................. 164 10.10.4 Receive Framer.................................................................................................................................. 164 10.10.5 C-bit DS3 Framer/Formatter .............................................................................................................. 168 10.10.6 M23 DS3 Framer/Formatter ............................................................................................................... 171 10.10.7 G.751 E3 Framer/Formatter............................................................................................................... 174 10.10.8 G.832 E3 Framer/Formatter............................................................................................................... 176 10.10.9 Clear-Channel Frame Processor ....................................................................................................... 181 10.11 HDLC OVERHEAD CONTROLLER .................................................................................................181 10.11.1 General Description ........................................................................................................................... 181 10.11.2 Features ............................................................................................................................................. 182 10.11.3 Transmit FIFO .................................................................................................................................... 182 10.11.4 Transmit HDLC Overhead Processor ................................................................................................ 182 10.11.5 Receive HDLC Overhead Processor ................................................................................................. 183 10.11.6 Receive FIFO ..................................................................................................................................... 184 10.12 TRAIL TRACE CONTROLLER .........................................................................................................184 10.12.1 General Description ........................................................................................................................... 184 10.12.2 Features ............................................................................................................................................. 185 10.12.3 Functional Description........................................................................................................................ 185 10.12.4 Transmit Data Storage ....................................................................................................................... 186 10.12.5 Transmit Trace ID Processor ............................................................................................................. 186 10.12.6 Transmit Trail Trace Processing ........................................................................................................ 186 10.12.7 Receive Trace ID Processor .............................................................................................................. 186 10.12.8 Receive Trail Trace Processing ......................................................................................................... 186 10.12.9 Receive Data Storage ........................................................................................................................ 187 10.13 FEAC CONTROLLER ...................................................................................................................188 10.13.1 General Description ........................................................................................................................... 188 10.13.2 Features ............................................................................................................................................. 188 10.13.3 Functional Description........................................................................................................................ 188 10.14 LINE ENCODER/DECODER ...........................................................................................................190 10.14.1 General Description ........................................................................................................................... 190 5 DS3181/DS3182/DS3183/DS3184 10.14.2 Features ............................................................................................................................................. 190 10.14.3 B3ZS/HDB3 Encoder ......................................................................................................................... 190 10.14.4 Transmit Line Interface ...................................................................................................................... 191 10.14.5 Receive Line Interface ....................................................................................................................... 191 10.14.6 B3ZS/HDB3 Decoder ......................................................................................................................... 191 10.15 BERT.........................................................................................................................................193 10.15.1 General Description ........................................................................................................................... 193 10.15.2 Features ............................................................................................................................................. 193 10.15.3 Configuration and Monitoring............................................................................................................. 193 10.15.4 Receive Pattern Detection ................................................................................................................. 194 10.15.5 Transmit Pattern Generation.............................................................................................................. 196 10.16 LINE INTERFACE UNIT (LIU).........................................................................................................197 10.16.1 General Description ........................................................................................................................... 197 10.16.2 Features ............................................................................................................................................. 197 10.16.3 Detailed Description ........................................................................................................................... 198 10.16.4 Transmitter ......................................................................................................................................... 198 10.16.5 Receiver ............................................................................................................................................. 199 11 OVERALL REGISTER MAP 202 12 REGISTER MAPS AND DESCRIPTIONS 204 12.1 REGISTERS BIT MAPS .................................................................................................................204 12.1.1 12.1.2 12.1.3 12.1.4 12.1.5 12.1.6 12.1.7 12.1.8 12.1.9 Global Register Bit Map ..................................................................................................................... 204 HDLC Register Bit Map...................................................................................................................... 207 T3 Register Bit Map ........................................................................................................................... 209 E3 G.751 Register Bit Map ................................................................................................................ 210 E3 G.832 Register Bit Map ................................................................................................................ 211 Clear-Channel Register Bit Map ........................................................................................................ 212 Fractional Register Bit Map................................................................................................................ 212 Transmit Cell Processor Bit Map ....................................................................................................... 215 Transmit Packet Processor Bit Map................................................................................................... 216 12.2 GLOBAL REGISTERS ....................................................................................................................219 12.2.1 Register Bit Descriptions.................................................................................................................... 219 12.3 UTOPIA/POS-PHY SYSTEM INTERFACE .....................................................................................227 12.3.1 Transmit System Interface ................................................................................................................. 227 12.3.2 Receive System Interface Register Map............................................................................................ 229 12.4 PER-PORT COMMON ...................................................................................................................231 12.4.1 Per-Port Common Register Map........................................................................................................ 231 12.4.2 Per-Port Common Register Bit Descriptions...................................................................................... 231 12.5 BERT.........................................................................................................................................242 12.5.1 BERT Register Map ........................................................................................................................... 242 12.5.2 BERT Register Bit Descriptions ......................................................................................................... 242 12.6 B3ZS/HDB3 LINE ENCODER/DECODER .......................................................................................251 12.6.1 Transmit Side Line Encoder/Decoder Register Map ......................................................................... 251 12.6.2 Receive Side Line Encoder/Decoder Register Map .......................................................................... 252 12.7 HDLC.........................................................................................................................................256 12.7.1 HDLC Transmit Side Register Map.................................................................................................... 256 12.7.2 HDLC Receive Side Register Map..................................................................................................... 260 12.8 FEAC CONTROLLER ...................................................................................................................264 12.8.1 FEAC Transmit Side Register Map.................................................................................................... 264 12.8.2 FEAC Receive Side Register Map..................................................................................................... 267 12.9 TRAIL TRACE ..............................................................................................................................270 12.9.1 Trail Trace Transmit Side................................................................................................................... 270 12.9.2 Trail Trace Receive Side Register Map ............................................................................................. 272 12.10 DS3/E3 FRAMER ........................................................................................................................276 12.10.1 Transmit DS3 ..................................................................................................................................... 276 12.10.2 Receive DS3 Register Map................................................................................................................ 279 12.10.3 Transmit G.751 E3 ............................................................................................................................. 289 6 DS3181/DS3182/DS3183/DS3184 12.10.4 Receive G.751 E3 Register Map ....................................................................................................... 291 12.10.5 Transmit G.832 E3 Register Map ...................................................................................................... 297 12.10.6 Receive G.832 E3 Register Map ....................................................................................................... 300 12.10.7 Transmit Clear Channel ..................................................................................................................... 309 12.10.8 Receive Clear Channel ...................................................................................................................... 310 12.11 FRACTIONAL DS3/E3 ..................................................................................................................312 12.11.1 Fractional Transmit Side Register Map.............................................................................................. 312 12.11.2 Fractional Receive Side Register Map............................................................................................... 314 12.12 DS3/E3 PLCP............................................................................................................................316 12.12.1 Transmit Side PLCP........................................................................................................................... 316 12.12.2 Receive Side PLCP Register Map ..................................................................................................... 320 12.13 FIFO REGISTERS ........................................................................................................................331 12.13.1 Transmit FIFO Register Map ............................................................................................................. 331 12.13.2 Receive FIFO Register Map .............................................................................................................. 335 12.14 CELL/PACKET PROCESSOR .........................................................................................................338 12.14.1 Transmit Cell Processor Register Map .............................................................................................. 338 12.14.2 Receive Cell Processor...................................................................................................................... 345 12.14.3 Transmit Packet Processor Register Map ......................................................................................... 357 12.14.4 Receive Packet Processor Register Map .......................................................................................... 362 13 JTAG INFORMATION 13.1 13.2 13.3 13.4 13.5 13.6 372 JTAG DESCRIPTION....................................................................................................................372 JTAG TAP CONTROLLER STATE MACHINE DESCRIPTION.............................................................373 JTAG INSTRUCTION REGISTER AND INSTRUCTIONS......................................................................375 JTAG ID CODES .........................................................................................................................376 JTAG FUNCTIONAL TIMING..........................................................................................................376 IO PINS ......................................................................................................................................376 14 PIN ASSIGNMENT 377 15 PACKAGE INFORMATION 380 15.1 400-LEAD TE-PBGA (27MM X 27MM, 1.27MM PITCH) (56-G6003-003) .......................................380 16 PACKAGE THERMAL INFORMATION 381 17 DC ELECTRICAL CHARACTERISTICS 382 18 AC TIMING CHARACTERISTICS 384 18.1 18.2 18.3 18.4 18.5 18.6 18.7 18.8 FRACTIONAL PORT CHARACTERISTICS .........................................................................................386 LINE INTERFACE AC CHARACTERISTICS .......................................................................................386 MISCELLANEOUS PIN AC CHARACTERISTICS ................................................................................387 OVERHEAD PORT AC CHARACTERISTICS .....................................................................................387 SYSTEM INTERFACE AC CHARACTERISTICS .................................................................................388 MICRO INTERFACE AC CHARACTERISTICS ...................................................................................390 CLAD JITTER CHARACTERISTICS ................................................................................................393 LIU INTERFACE AC CHARACTERISTICS ........................................................................................393 18.8.1 Waveform Templates ......................................................................................................................... 393 18.8.2 LIU Input/Output Characteristics........................................................................................................ 397 18.9 JTAG INTERFACE AC CHARACTERISTICS ....................................................................................399 19 REVISION HISTORY 400 7 DS3181/DS3182/DS3183/DS3184 LIST OF FIGURES Figure 1-1. LIU External Connections for a DS3/E3/STS-1 Port of a DS318x Device.............................................. 14 Figure 1-2. DS318x Functional Block Diagram ......................................................................................................... 14 Figure 2-1. Four-Port Unchannelized ATM over DS3/E3/CC52 Line Card ............................................................... 15 Figure 2-2. Four-Port Unchannelized HDLC over DS3/E3/CC52 Line Card ............................................................. 16 Figure 6-1. DS3/E3 ATM/Packet Mode ..................................................................................................................... 26 Figure 6-2. DS3/E3 ATM/Packet--OHM Mode ......................................................................................................... 27 Figure 6-3. DS3/E3 Internal Fractional ATM/Packet Mode ....................................................................................... 28 Figure 6-4. DS3/E3 External Fractional ATM/Packet Mode ...................................................................................... 29 Figure 6-5. DS3/E3 Flexible External Fractional Mode ............................................................................................. 30 Figure 6-6. DS3/E3 G.751 PLCP ATM Mode ............................................................................................................ 31 Figure 6-7. DS3/E3 G.751 PLCP ATM--OHM Mode ................................................................................................ 33 Figure 6-8. Clear-Channel ATM/Packet Modes......................................................................................................... 34 Figure 6-9. Clear-Channel ATM/Packet--OHM Mode .............................................................................................. 35 Figure 6-10. Clear-Channel Octet Aligned ATM/Packet--OHM Mode...................................................................... 36 Figure 7-1. HDB3/B3ZS/AMI LIU Mode..................................................................................................................... 38 Figure 7-2. HDB3/B3ZS/AMI Non-LIU Line Interface Mode...................................................................................... 39 Figure 7-3. UNI Line Interface Mode ......................................................................................................................... 40 Figure 7-4. UNI Line Interface--OHM Mode ............................................................................................................. 41 Figure 8-1. TX Line IO B3ZS Functional Timing Diagram ......................................................................................... 66 Figure 8-2. TX Line IO HDB3 Functional Timing Diagram ........................................................................................ 67 Figure 8-3. RX Line IO B3ZS Functional Timing Diagram......................................................................................... 67 Figure 8-4. RX Line IO HDB3 Functional Timing Diagram ........................................................................................ 68 Figure 8-5. TX Line IO UNI OHM Functional Timing Diagram .................................................................................. 68 Figure 8-6. TX Line IO UNI Octet Aligned OHM Functional Timing Diagram............................................................ 68 Figure 8-7. RX Line IO OHM UNI Functional Timing Diagram.................................................................................. 69 Figure 8-8. RX Line IO UNI Octet Aligned OHM Functional Timing Diagram ........................................................... 69 Figure 8-9. DS3 Framing Receive Overhead Port Timing......................................................................................... 69 Figure 8-10. E3 G.751 Framing Receive Overhead Port Timing .............................................................................. 70 Figure 8-11. E3 G.832 Framing Receive Overhead Port Timing .............................................................................. 70 Figure 8-12. DS3 Framing Transmit Overhead Port Timing...................................................................................... 70 Figure 8-13. E3 G.751 Framing Transmit Overhead Port Timing ............................................................................. 70 Figure 8-14. E3 G.832 Framing Transmit Overhead Port Timing ............................................................................. 71 Figure 8-15. DS3 PLCP Receive Overhead Port Timing........................................................................................... 71 Figure 8-16. E3 G.751 PLCP Receive Overhead Port Timing .................................................................................. 71 Figure 8-17. DS3 PLCP Transmit Overhead Port Timing.......................................................................................... 71 Figure 8-18. E3 G.751 PLCP Transmit Overhead Port Timing ................................................................................. 72 Figure 8-19. External (XFRAC) Transmit Fractional Timing...................................................................................... 72 Figure 8-20. External (XFRAC) Receive Fractional Timing....................................................................................... 72 Figure 8-21. Internal (IFRAC) Transmit Fractional Timing ........................................................................................ 73 Figure 8-22. Internal (IFRAC) Receive Fractional Timing ......................................................................................... 73 Figure 8-23. Transmit Flexible Fractional (FFRAC) Timing....................................................................................... 74 Figure 8-24. Receive Flexible Fractional (FFRAC) Timing........................................................................................ 74 Figure 8-25. UTOPIA Level 2 Transmit Cell Transfer Direct Mode ........................................................................... 75 Figure 8-26. UTOPIA Level 2 Receive Cell Transfer Direct Mode ............................................................................ 76 Figure 8-27. UTOPIA Level 2 Transmit Multiple Cell Transfer Polled Mode ............................................................. 77 Figure 8-28. UTOPIA Level 2 Receive Multiple Cell Transfer Polled Mode .............................................................. 77 Figure 8-29. UTOPIA Level 2 Receive Unexpected Multiple Cell Transfer............................................................... 78 Figure 8-30. UTOPIA Level 3 Transmit Multiple Cell Transfer Direct Mode.............................................................. 78 Figure 8-31. UTOPIA Level 3 Transmit Multiple Cell Transfer Polled Mode ............................................................. 79 Figure 8-32. UTOPIA Level 3 Receive Multiple Cell Transfer Direct Mode............................................................... 80 Figure 8-33. UTOPIA Level 3 Receive Multiple Cell Transfer Polled Mode .............................................................. 80 Figure 8-34. Transmit Multiple Packet Transfer to Different PHY ports (direct status mode) ................................... 81 Figure 8-35. POS-PHY Level 2 Receive Multiple Packet Transfer from Different PHY Ports/Devices(direct status mode)............................................................................................................ 82 Figure 8-36. POS-PHY Level 2 Transmit Multiple Packet Transfer to Different PHY Ports (polled status mode) .... 83 Figure 8-37. POS-PHY Level 2 Receive Multiple Packet Transfer (polled status mode).......................................... 84 Figure 8-38. POS-PHY Level 3 Transmit Multiple Packet Transfer In-Band Addressing.......................................... 85 8 DS3181/DS3182/DS3183/DS3184 Figure 8-39. POS-PHY Level 3 Receive Multiple Packet Transfer In-Band Addressing........................................... 86 Figure 8-40. 16-Bit Mode Write.................................................................................................................................. 87 Figure 8-41. 16-Bit Mode Read ................................................................................................................................. 87 Figure 8-42. 8-Bit Mode Write.................................................................................................................................... 88 Figure 8-43. 8-Bit Mode Read ................................................................................................................................... 88 Figure 8-44. 16-Bit Mode without Byte Swap ............................................................................................................ 89 Figure 8-45. 16-Bit Mode with Byte Swap ................................................................................................................. 89 Figure 8-46. Clear Status Latched Register on Read................................................................................................ 90 Figure 8-47. Clear Status Latched Register on Write................................................................................................ 90 Figure 8-48. RDY Signal Functional Timing Writes ................................................................................................... 90 Figure 8-49. RDY Signal Functional Timing Read..................................................................................................... 91 Figure 10-1. Interrupt Structure ................................................................................................................................. 98 Figure 10-2. Internal TX Clock................................................................................................................................. 101 Figure 10-3. Internal RX Clock ................................................................................................................................ 102 Figure 10-4. Example IO Pin Clock Muxing............................................................................................................. 106 Figure 10-5. Reset Sources..................................................................................................................................... 107 Figure 10-6. CLAD Block ......................................................................................................................................... 110 Figure 10-7. 8KREF Logic ....................................................................................................................................... 112 Figure 10-8. Performance Monitor Update Logic .................................................................................................... 115 Figure 10-9. Transmit Error Insert Logic.................................................................................................................. 116 Figure 10-10. Loopback Modes ............................................................................................................................... 117 Figure 10-11. ALB Mux............................................................................................................................................ 117 Figure 10-12. AIS Signal Flow ................................................................................................................................. 120 Figure 10-13. DS3 C-Bit or DS3 M23 (with C-Bit Generation) Frame..................................................................... 128 Figure 10-14. DS3 PLCP Frame.............................................................................................................................. 129 Figure 10-15. DS3 M23 (with C-Bits Used as Payload) Frame............................................................................... 130 Figure 10-16. E3 G.751 Frame................................................................................................................................ 130 Figure 10-17. E3 PLCP Frame ................................................................................................................................ 131 Figure 10-18. Example E3 G.751 Internal Fractional Frame................................................................................... 131 Figure 10-19. E3 G.832 Frame................................................................................................................................ 132 Figure 10-20. System Interface Functional Diagram ............................................................................................... 134 Figure 10-21. Normal Packet Format in 32-Bit Mode .............................................................................................. 135 Figure 10-22. Normal Packet Format in 16-Bit Mode .............................................................................................. 135 Figure 10-23. Byte Reordered Packet Format in 32-Bit Mode ................................................................................ 135 Figure 10-24. Byte Reordered Packet Format in 16-Bit Mode ................................................................................ 136 Figure 10-25. ATM Cell/HDLC Packet Functional Diagram .................................................................................... 139 Figure 10-26. Receive DSS Scrambler Synchronization State Diagram................................................................. 143 Figure 10-27. Cell Delineation State Diagram ......................................................................................................... 144 Figure 10-28. HEC Error Monitoring State Diagram................................................................................................ 145 Figure 10-29. Cell Format for 53-Byte Cell With 32-Bit Data Bus ........................................................................... 145 Figure 10-30. Cell Format for 52-Byte Cell With 32-Bit Data Bus ........................................................................... 146 Figure 10-31. PLCP Framer Functional Diagram .................................................................................................... 150 Figure 10-32. DS3 PLCP Frame Format ................................................................................................................. 152 Figure 10-33. DS3 PLCP G1 Byte Format .............................................................................................................. 152 Figure 10-34. E3 PLCP Frame Format.................................................................................................................... 156 Figure 10-35. E3 PLCP G1 Byte Format ................................................................................................................. 156 Figure 10-36. Fractional Payload Controller Detailed Block Diagram ..................................................................... 160 Figure 10-37. Data Group Format ........................................................................................................................... 162 Figure 10-38. Frame Format.................................................................................................................................... 162 Figure 10-39. Framer Detailed Block Diagram ........................................................................................................ 163 Figure 10-40. DS3 Frame Format............................................................................................................................ 165 Figure 10-41. DS3 Sub-Frame Framer State Diagram............................................................................................ 166 Figure 10-42. DS3 Multiframe Framer State Diagram............................................................................................. 167 Figure 10-43. G.751 E3 Frame Format ................................................................................................................... 174 Figure 10-44. G.832 E3 Frame Format ................................................................................................................... 176 Figure 10-45. MA Byte Format ................................................................................................................................ 177 Figure 10-46. HDLC Controller Block Diagram ....................................................................................................... 182 Figure 10-47. Trail Trace Controller Block Diagram ................................................................................................ 185 Figure 10-48. Trail Trace Byte (DT = Trail Trace Data)........................................................................................... 187 9 DS3181/DS3182/DS3183/DS3184 Figure 10-49. FEAC Controller Block Diagram........................................................................................................ 188 Figure 10-50. FEAC Codeword Format................................................................................................................... 189 Figure 10-51. Line Encoder/Decoder Block Diagram .............................................................................................. 190 Figure 10-52. B3ZS Signatures ............................................................................................................................... 192 Figure 10-53. HDB3 Signatures............................................................................................................................... 192 Figure 10-54. BERT Block Diagram ........................................................................................................................ 193 Figure 10-55. PRBS Synchronization State Diagram.............................................................................................. 195 Figure 10-56. Repetitive Pattern Synchronization State Diagram........................................................................... 196 Figure 10-57. LIU Functional Diagram..................................................................................................................... 197 Figure 10-58. DS3/E3/STS-1 LIU Block Diagram.................................................................................................... 198 Figure 10-59. Receiver Jitter Tolerance .................................................................................................................. 201 Figure 13-1. JTAG Block Diagram........................................................................................................................... 372 Figure 13-2. JTAG TAP Controller State Machine .................................................................................................. 373 Figure 13-3. JTAG Functional Timing...................................................................................................................... 376 Figure 14-1. DS3184 Pin Assignments--400-Lead TE-PBGA................................................................................ 377 Figure 14-2. DS3183 Pin Assignments--400-Lead TE-PBGA................................................................................ 378 Figure 14-3. DS3182 Pin Assignments--400-Lead TE-PBGA................................................................................ 378 Figure 14-4. DS3181 Pin Assignments--400-Lead TE-PBGA................................................................................ 379 Figure 18-1. Clock Period and Duty Cycle Definitions............................................................................................. 384 Figure 18-2. Rise Time, Fall Time, and Jitter Definitions......................................................................................... 384 Figure 18-3. Hold, Setup, and Delay Definitions (Rising Clock Edge) .................................................................... 384 Figure 18-4. Hold, Setup, and Delay Definitions (Falling Clock Edge).................................................................... 385 Figure 18-5. To/From High-Z Delay Definitions (Rising Clock Edge)...................................................................... 385 Figure 18-6. To/From High-Z Delay Definitions (Falling Clock Edge) ..................................................................... 385 Figure 18-7. Micro Interface Nonmultiplexed Read/Write Cycle ............................................................................. 391 Figure 18-8. Micro Interface Multiplexed Read Cycle.............................................................................................. 392 Figure 18-9. E3 Waveform Template....................................................................................................................... 395 Figure 18-10. STS-1 Pulse Mask Template ............................................................................................................ 396 Figure 18-11. DS3 Pulse Mask Template................................................................................................................ 397 10 DS3181/DS3182/DS3183/DS3184 LIST OF TABLES Table 4-1. Standards Compliance ............................................................................................................................. 23 Table 6-1. DS3/E3 ATM/Packet Mode Configuration Registers................................................................................ 26 Table 6-2. DS3/E3 ATM/Packet--OHM Mode Configuration Registers.................................................................... 27 Table 6-3. DS3/E3 Internal Fractional (IFRAC) ATM/Packet Mode Configuration Registers ................................... 28 Table 6-4. DS3/E3 External Fractional (XFRAC) ATM/Packet Mode Configuration Registers................................. 29 Table 6-5. DS3/E3 Flexible External Fractional (Subrate) Mode Configuration Registers........................................ 30 Table 6-6. DS3/E3 G.751 PLCP ATM Mode Configuration Registers ...................................................................... 31 Table 6-7. DS3/E3 G.751 PLCP ATM--OHM Mode Configuration Registers .......................................................... 32 Table 6-8. Clear-Channel ATM/Packet Mode Configuration Modes ......................................................................... 34 Table 6-9. Clear-Channel ATM/Packet--OHM Mode Configuration Registers......................................................... 35 Table 6-10. Clear-Channel Octet Aligned ATM/Packet--OHM Mode Configuration Registers................................ 36 Table 7-1. HDB3/B3ZS/AMI LIU Mode Configuration Registers ............................................................................... 37 Table 7-2. HDB3/B3ZS/AMI Non-LIU Mode Configuration Registers ....................................................................... 39 Table 7-3. UNI Line Interface Mode Configuration Registers.................................................................................... 40 Table 7-4. UNI Line Interface--OHM Mode Configuration Registers........................................................................ 41 Table 8-1. DS3184 Short Pin Descriptions................................................................................................................ 42 Table 8-2. Detailed Pin Descriptions ......................................................................................................................... 48 Table 9-1. Configuration of Global Register Settings ................................................................................................ 93 Table 9-2. Configuration of Port Register Settings .................................................................................................... 93 Table 10-1. LIU Enable Table.................................................................................................................................. 100 Table 10-2. All Possible Clock Sources Based on Mode and Loopback................................................................. 100 Table 10-3. Source Selection of TLCLK Clock Signal ............................................................................................. 101 Table 10-4. Source Selection of TCLKOn (internal TX clock) ................................................................................. 102 Table 10-5. Source Selection of RCLKO Clock Signal (internal RX clock) ............................................................. 102 Table 10-6. Transmit Line Interface Signal Pin Valid Timing Source Select ........................................................... 103 Table 10-7. Transmit Framer Pin Signal Timing Source Select .............................................................................. 104 Table 10-8. Receive Line Interface Pin Signal Timing Source Select ..................................................................... 104 Table 10-9. Receive Framer Pin Signal Timing Source Select ............................................................................... 105 Table 10-10. Reset and Power-Down Sources ....................................................................................................... 108 Table 10-11. CLAD IO Pin Decode.......................................................................................................................... 111 Table 10-12. Global 8 kHz Reference Source Table............................................................................................... 112 Table 10-13. Port 8 kHz Reference Source Table................................................................................................... 112 Table 10-14. GPIO Global Signals .......................................................................................................................... 113 Table 10-15. GPIO Pin Global Mode Select Bits..................................................................................................... 113 Table 10-16. GPIO Port Alarm Monitor Select ........................................................................................................ 114 Table 10-17. Loopback Mode Selections ................................................................................................................ 116 Table 10-18. Line AIS Enable Modes ...................................................................................................................... 120 Table 10-19. Payload (Downstream) AIS Enable Modes ........................................................................................ 121 Table 10-20. TSOFIn/TOHMIn Input Pin Functions ................................................................................................ 122 Table 10-21. TSERn/TPOHn/TFOHn Input Pin Functions ...................................................................................... 122 Table 10-22. TPDENIn/TPOHENn/TFOHENIn Input Pin Functions ....................................................................... 123 Table 10-23. TSOFOn/TDENn/TPOHSOFn/TFOHENOn Output Pin Functions .................................................... 123 Table 10-24. TCLKOn/TGCLKn/TPOHCLKn Output Pin Functions........................................................................ 124 Table 10-25. TPDATn Input Pin Functions.............................................................................................................. 124 Table 10-26. TPDENOn Output Pin Functions........................................................................................................ 124 Table 10-27. RSERn/RPOHn Output Pin Functions ............................................................................................... 125 Table 10-28. RPDENIn/RFOHENIn Input Pin Functions......................................................................................... 125 Table 10-29. RPDATn Input Pin Functions ............................................................................................................. 125 Table 10-30. RSOFOn/RDENn/RPOHSOFn/RFOHENOn Output Pin Functions................................................... 126 Table 10-31. RCLKOn/RGCLKn/RPOHCLKn Output Pin Functions ...................................................................... 126 Table 10-32. Framing Mode Select Bits FM[5:0] ..................................................................................................... 127 Table 10-33. Line Mode Select Bits LM[2:0]............................................................................................................ 133 Table 10-34. C-Bit DS3 Frame Overhead Bit Definitions ........................................................................................ 169 Table 10-35. M23 DS3 Frame Overhead Bit Definitions ......................................................................................... 171 Table 10-36. G.832 E3 Frame Overhead Bit Definitions ......................................................................................... 177 Table 10-37. Payload Label Match Status............................................................................................................... 180 Table 10-38. Pseudorandom Pattern Generation.................................................................................................... 194 11 DS3181/DS3182/DS3183/DS3184 Table 10-39. Repetitive Pattern Generation ............................................................................................................ 194 Table 10-40. Transformer Characteristics ............................................................................................................... 199 Table 10-41. Recommended Transformers............................................................................................................. 200 Table 11-1. Global and Test Register Address Map ............................................................................................... 203 Table 11-2. Per-Port Register Address Map ........................................................................................................... 203 Table 12-1. Global Register Bit Map........................................................................................................................ 204 Table 12-2. System Interface Bit Map ..................................................................................................................... 205 Table 12-3. Port Register Bit Map ........................................................................................................................... 205 Table 12-4. BERT Register Bit Map ........................................................................................................................ 206 Table 12-5. LINE Register Bit Map .......................................................................................................................... 206 Table 12-6. HDLC Register Bit Map ........................................................................................................................ 207 Table 12-7. FEAC Register Bit Map ........................................................................................................................ 208 Table 12-8. Trail Trace Register Bit Map................................................................................................................. 208 Table 12-9. T3 Register Bit Map.............................................................................................................................. 209 Table 12-10. E3 G.751 Register Bit Map................................................................................................................. 210 Table 12-11. E3 G.832 Register Bit Map................................................................................................................. 211 Table 12-12. Clear-Channel Register Bit Map......................................................................................................... 212 Table 12-13. Fractional Register Bit Map ................................................................................................................ 212 Table 12-14. PLCP Register Bit Map....................................................................................................................... 213 Table 12-15. FIFO Register Bit Map........................................................................................................................ 214 Table 12-16. Transmit Cell Processor Register Bit Map ......................................................................................... 215 Table 12-17. Transmit Packet Processor Register Bit Map .................................................................................... 216 Table 12-18. Receive Cell Processor Register Bit Map .......................................................................................... 216 Table 12-19. Receive Packet Processor Register Bit Map ..................................................................................... 217 Table 12-20. Global Register Map........................................................................................................................... 219 Table 12-21. Transmit System Interface Register Map ........................................................................................... 227 Table 12-22. Receive System Interface Register Map ............................................................................................ 229 Table 12-23. Per-Port Common Register Map ........................................................................................................ 231 Table 12-24. BERT Register Map............................................................................................................................ 242 Table 12-25. Transmit Side B3ZS/HDB3 Line Encoder/Decoder Register Map ..................................................... 251 Table 12-26. Receive Side B3ZS/HDB3 Line Encoder/Decoder Register Map ...................................................... 252 Table 12-27. Transmit Side HDLC Register Map .................................................................................................... 256 Table 12-28. Receive Side HDLC Register Map ..................................................................................................... 260 Table 12-29. FEAC Transmit Side Register Map .................................................................................................... 264 Table 12-30. FEAC Receive Side Register Map ..................................................................................................... 267 Table 12-31. Transmit Side Trail Trace Register Map............................................................................................. 270 Table 12-32. Trail Trace Receive Side Register Map.............................................................................................. 272 Table 12-33. Transmit DS3 Framer Register Map .................................................................................................. 276 Table 12-34. Receive DS3 Framer Register Map ................................................................................................... 279 Table 12-35. Transmit G.751 E3 Framer Register Map .......................................................................................... 289 Table 12-36. Receive G.751 E3 Framer Register Map ........................................................................................... 291 Table 12-37. Transmit G.832 E3 Framer Register Map .......................................................................................... 297 Table 12-38. Receive G.832 E3 Framer Register Map ........................................................................................... 300 Table 12-39. Transmit Clear-Channel Register Map............................................................................................... 309 Table 12-40. Receive Clear-Channel Register Map................................................................................................ 310 Table 12-41. Fractional Transmit Side Register Map .............................................................................................. 312 Table 12-42. Receive Side Register Map................................................................................................................ 314 Table 12-43. Transmit Side PLCP Register Map .................................................................................................... 316 Table 12-44. Receive Side PLCP Register Map ..................................................................................................... 320 Table 12-45. Transmit FIFO Register Map.............................................................................................................. 331 Table 12-46. Receive FIFO Register Map............................................................................................................... 335 Table 12-47. Transmit Cell Processor Register Map............................................................................................... 338 Table 12-48. HEC Error Mask ................................................................................................................................. 341 Table 12-49. Receive Cell Processor Register Map................................................................................................ 345 Table 12-50. Transmit Packet Processor Register Map.......................................................................................... 357 Table 12-51. Receive Packet Processor Register Map........................................................................................... 362 Table 13-1. JTAG Instruction Codes ....................................................................................................................... 375 Table 13-2. JTAG ID Codes .................................................................................................................................... 376 Table 14-1. Pin Assignment Breakdown ................................................................................................................. 377 12 DS3181/DS3182/DS3183/DS3184 Table 17-1. Recommended DC Operating Conditions ............................................................................................ 382 Table 17-2. DC Electrical Characteristics................................................................................................................ 382 Table 17-3. Output Pin Drive ................................................................................................................................... 383 Table 18-1. Fractional Port Timing .......................................................................................................................... 386 Table 18-2. Line Interface Timing ............................................................................................................................ 386 Table 18-3. Miscellaneous Pin Timing..................................................................................................................... 387 Table 18-4. Overhead Port Timing .......................................................................................................................... 387 Table 18-5. System Interface L2 Timing.................................................................................................................. 388 Table 18-6. System Interface L3 Timing.................................................................................................................. 389 Table 18-7. Micro Interface Timing .......................................................................................................................... 390 Table 18-8. DS3 Waveform Template ..................................................................................................................... 393 Table 18-9. DS3 Waveform Test Parameters and Limits ........................................................................................ 393 Table 18-10. STS-1 Waveform Template ................................................................................................................ 394 Table 18-11. STS-1 Waveform Test Parameters and Limits................................................................................... 394 Table 18-12. E3 Waveform Test Parameters and Limits......................................................................................... 395 Table 18-13. Receiver Input Characteristics--DS3 and STS-1 Modes................................................................... 397 Table 18-14. Receiver Input Characteristics--E3 Mode ......................................................................................... 398 Table 18-15. Transmitter Output Characteristics--DS3 and STS-1 Modes............................................................ 398 Table 18-16. Transmitter Output Characteristics--E3 Mode .................................................................................. 398 Table 18-17. JTAG Interface Timing........................................................................................................................ 399 13 DS3181/DS3182/DS3183/DS3184 1 BLOCK DIAGRAMS Figure 1-1 shows the external components required at each LIU interface for proper operation. Figure 1-2 shows the functional block diagram of one channel ATM/Packet PHY. Figure 1-1. LIU External Connections for a DS3/E3/STS-1 Port of a DS318x Device Each T3/E3 LIU f TXP VDD Transmit 330 (1%) VDD TXN VDD RXP VSS 1:2ct 0.01uF 0.1uF 1uF 0.01uF 0.1uF 1uF 0.01uF 0.1uF 1uF 3.3V Power Plane Receive 330 (1%) Ground Plane VSS RXN VSS 1:2ct TPOHENn/TFOHENIn/ TPDENIn TPOHSOFn/TSOFOn/ TDENn\TFOHENOn TPOHCLKN/ TCLKOn/TGCLKn TPDENOn TPDATn TPOHn/TFOHn/TSERn TCLKIn TOHENn TOHn TOHCLKn TOHSOFn TOHMIn/TSOFIn Figure 1-2. DS318x Functional Block Diagram TAIS TPOSn/ TDATn TUA1 RX FRAC/ PLCP UA1 GEN 14 System Interface SLB RDY MODE WIDTH INT GPIO[8:1] ALE CS RD/DS WR/ R/W Microprocessor Interface RST IEEE P1149.1 JTAG Test Access Port TSCLK TADR[4:0] TDATA[31:0] TPRTY TEN TDXA[4:2] TDXA[1]/TPXA TSOX TSPA TEOP TSX TMOD[1:0] TERR RSCLK RADR[4:0] RDATA[31:0] RPRTY REN RDXA[1]/RPXA /RSX RDXA[4:2] RSOX REOP RVAL RMOD[1:0] RERR Rx FIFO Rx Cell Processor A[10:1] A[0]/BSWAP DS3 / E3 Receive Framer D[15:0] DS318x RX BERT Rx Packet Processor RFOHENIn/RPDENIn RPDATn CLKC CLKB CLKA Clock Rate Adapter B3ZS/ HDB3 Decoder TX BERT HDLC RPOHn/RSERn RPOHSOFn/RSOFOn/ RDENn/ RFOHENOn RPOHCLKn/ RCLKOn/RGCLKn DS3/E3 Receive LIU RXPn RXNn Trail FEAC Trace Buffer Tx FIFO Tx Packet Processor PLB LLB ALB RLCLKn RPOSn/ RDATn RNEGn/ RLCVn/ ROHMIn TX FRAC/ PLCP ROHn ROHCLKn ROHSOFn TXNn JTRST JTCLK JTMS JTDI JTDO TXPn Tx Cell Processor DS3 / E3 Transmit Formatter B3ZS/ HDB3 Encoder DS3/E3 Transmit LIU DLB TNEGn/ TOHMOn/ TLCLKn n = port # (1-4) DS3181/DS3182/DS3183/DS3184 2 * * * * * * * * * * * APPLICATIONS Access Concentrators Multiservice Access Platforms ATM and Frame Relay Equipment Routers and Switches SONET/SDH ADM SONET/SDH Muxes PBXs Digital Cross Connect PDH Multiplexer/Demultiplexer Test Equipment Integrated Access Device (IAD) Figure 2-1 and Figure 2-2 show applications for the DS3184 as four-port unchannelized ATM and packet DS3/E3 line cards, respectively. Figure 2-1. Four-Port Unchannelized ATM over DS3/E3/CC52 Line Card Typical ATM Line Card x DS3/E3 Line DS315x #1 DS3154 4- Chan DS3/E DS3/E3 LIU Utopia POSPHY DS316x #1 DS3164 4- Chan DS3/E DS3/E3 ATM PH PHY 2/3 AT ATM Switch Card (S/W+ Igr/Egr Mgt) DS318x x DS3/E3 Line DS315x #3 DS3154 4- Chan DS3/E DS3/E3 LIU DS316x #3 DS3164 4- Chan DS3/E DS3/E3 ATM PH PHY X = 1, 2, 3, 4 Typical ATM Line Card 15 Utopia POS PHY 2/3 OC- n OC-12 AT ATM SAR DS3181/DS3182/DS3183/DS3184 Figure 2-2. Four-Port Unchannelized HDLC over DS3/E3/CC52 Line Card Typical Packet Line Card x DS3/E3 Line DS315x #1 DS3154 4- Chan DS3/E DS3/E3 LIU Utopia POSPHY DS316x #1 DS3164 4- Chan DS3/E DS3/E3 ATM PKT PH PHY 2/3 AT IP/PKT Switch Card (S/W+ Igr/Egr Mgt) DS318x x DS3/E3 Line DS315x #3 DS3154 4- Chan DS3/E DS3/E3 LIU DS316x #3 DS3164 4- Chan DS3/E DS3/E3 ATM PH PHY X = 1, 2, 3, 4 Typical Packet Line Card 16 Utopia POSPHY 2/3 OC- n OC-12 AT POS SAR DS3181/DS3182/DS3183/DS3184 3 FEATURE DETAILS The following sections describe the features provided by the DS3181 (single), DS3182 (dual), DS3183 (triple), and DS3184 (quad) PHYs. 3.1 * * * * * * * * * * * * * * * * 3.2 * * * * * 3.3 * * * Global Features System interface configurable for UTOPIA L2/UTOPIA L3 for ATM cell traffic or POS-PHY L2/POS-PHY L3 or SPI-3 for HDLC packets or mixed packet/cell traffic Supports the following transmission protocols: * Direct-mapped ATM over DS3 or sub-rate DS3 * PLCP-mapped ATM over DS3 * Direct-mapped ATM over G.751 E3 or sub-rate G.751 E3 * PLCP-mapped ATM over G.751 E3 * Direct-mapped ATM over G.832 E3 or sub-rate G.832 E3 * Bit or byte synchronous (octet aligned) direct-mapped ATM over externally-defined frame formats up to 52 Mbps * Clear-channel ATM (cell-based physical layer) at line rates up to 52 Mbps * Clear-channel ATM DSS at line rates up to 52 Mbps * Direct-mapped HDLC over DS3 or sub-rate DS3 * Direct-mapped HDLC over G.751 E3 or sub-rate G.751 E3 * Direct-mapped HDLC over G.832 E3 or sub-rate G.832 E3 * Bit or byte synchronous (octet aligned) direct-mapped HDLC over externally-defined frame formats up to 52 Mbps * Clear-channel HDLC at line rates up to 52 Mbps In UTOPIA bus mode, ports are independently configurable for any ATM protocol In POS-PHY bus mode, ports are independently configurable for any ATM or HDLC protocol Programmable to support internally or externally controlled sub-rate DS3 or E3 on any ports Supports gapped 52 MHz clock rates for signals embedded in SONET/SDH Optional transmit loop timed clock(s) mode using the associated port's receive clock(s) Optional transmit clock mode using references generated by the internal Clock Rate Adapter (CLAD) Requires only a single reference clock for all three LIU data rates using internal CLAD The LIU can be powered down and bypassed for direct logic IO to/from line circuits. Jitter attenuator can be placed in either transmit or receive path when the LIU is enabled. Clock, data and control signals can be inverted for a direct interface to many other devices Detection of loss of transmit clock and loss of receive clock Automatic one-second, external or manual update of performance monitoring counters Each port can be placed into a low-power standby mode when not being used Framing and line code error insertion available Receive DS3/E3/STS-1 LIU Features AGC/Equalizer block handles from 0 dB to 15 dB of cable loss Loss-of-lock PLL status indication Interfaces directly to a DSX monitor signal (20 dB flat loss) using built-in pre-amp Digital and analog Loss of Signal (LOS) detectors (ANSI T1.231 and ITU G.775) Per-channel power-down control Receive DS3/E3 Framer Features Frame synchronization for M23 or C-bit Parity DS3, or G.751 E3 or G.832 E3 B3ZS/HDB3/AMI decoding Detection and accumulation of bipolar violations (BPV), code violations (CV), excessive zeroes occurrences (EXZ), F-bit errors, M-bit errors, FAS errors, LOF occurrences, P-bit parity errors, CP-bit parity errors, BIP-8 errors, and far end block errors (FEBE) 17 DS3181/DS3182/DS3183/DS3184 * * * * * * * 3.4 * * * * * * * 3.5 * * * * * * * * * * * 3.6 * * * * * * * * * * * Detection of RDI, AIS, DS3 idle signal, loss of signal (LOS), severely errored framing event (SEFE), change of frame alignment (COFA), receipt of B3ZS/HDB3 code words, DS3 application ID bit, DS3 M23/C-bit format mismatch, G.751 national bit, and G.832 RDI (FERF), payload type, and timing marker bits HDLC port for DS3 path maintenance data link (PMDL), G.751 national bit or G.832 NR or GC channels FEAC port for DS3 FEAC channel 16-byte Trail Trace Buffer port for G.832 trail access point identifier DS3 M23 C bits and stuff bits configurable as payload or overhead, stored in registers for software inspection Most framing overhead fields presented on the receive overhead port Support for internal and external subrate DS3/E3 control (Fractional DS3/E3) Receive PLCP Framer Features PLCP frame synchronization C1 cycle/stuff counter interpretation Detection of out of frame (OOF), BIP-8 errors, FEBE and RAI (Yellow Signal) Frame timing can be presented on the GPIO2 output pin or used as the transmit PLCP reference All path overhead fields presented on the PLCP receive overhead port HDLC port for data link messages on F1, M1 or M2 bytes Trail Trace port for trace messages on F1 byte Receive Cell Processor Features HEC-based cell delineation within the DS3/E3 frame, the PLCP frame, an externally defined frame, or the entire line bandwidth Cell descrambling using the self-synchronizing scrambler (x43+1) for ATM over DS3/E3 Distributed Sample Scrambler (DSS) for clear-channel ATM (cell-based physical layer) HEC error detection and correction; HEC discard Filtering of idle, unassigned and/or invalid cells (provisionable) Header pattern comparison vs. 32-bit header pattern and mask registers; counting of matching or nonmatching cells; discard of matching or non-matching cells Four-cell Receive FIFO Controls include enables/disables/settings for: cell processing, coset polynomial addition, error correction, erred cell extraction, cell descrambling, idle/unassigned/invalid cell filtering, header pattern match counting/discarding, LCD integration time Status fields include: out of cell delineation (OCD), loss of cell delineation (LCD) and receipt of idle, unassigned, invalid, erred, corrected or header-pattern-match cells Performance monitoring counters for forwarded cells, corrected cells, uncorrectable cells, header pattern match/no-match cells, and filtered idle/unassigned/invalid cells Octet alignment option for externally defined frame formats Receive Packet Processor Features Packet descrambling using the self-synchronizing scrambler (x43+1) Flag detection, packet delineation, and inter-frame fill discard (flags and all-ones) Packet abort detection and accumulation Bit or octet destuffing FCS checking (16-bit or 32-bit), error accumulation, and FCS discard Packet size checking vs. programmable minimum and maximum size registers Abort declaration for packets with non-integral number of bytes Controls include enables/disables/settings for: packet processing, descrambling, 16/32-bit FCS, filtering of FCS erred packets, FCS discard, minimum/maximum packet size Status fields include: receipt of FCS erred packet, aborted packet, size violation packet, non-integer-length packets Performance monitoring counters for forwarded packets, forwarded bytes, aborted bytes, FCS erred packets, aborted packets, size violation packets (min, max, non-integer-length) Octet alignment with octet destuffing option for externally defined frame formats 18 DS3181/DS3182/DS3183/DS3184 3.7 * * * * 3.8 * * * * 3.9 * * * * Receive FIFO Features Storage capacity for four cells or 256 bytes of packet data per port Programmable port address Programmable fill level thresholds Underflow and overflow status indications Receive System Interface Features UTOPIA L2 / UTOPIA L3 interface in cell mode, POS-PHY L2 / POS-PHY L3 or SPI-3 interface in packet or mixed traffic modes 8, 16, or 32-bit data bus at clock rates from 10 MHz to 66 MHz (52 MHz in L2 modes) Polled and direct cell available outputs Controls include enables/disables/settings for: HEC transfer, signal inversions, parity enable/polarity, cell available deassertion time Transmit System Interface Features UTOPIA L2 / UTOPIA L3 interface in cell mode, POS-PHY L2 / POS-PHY L3 or SPI-3 interface in packet or mixed traffic modes 8, 16, or 32-bit data bus at clock rates from 10 MHz to 66 MHz (52 MHz in L2 modes) Polled and direct cell available outputs Controls include enables/disables/settings for: HEC transfer, signal inversions, parity enable/polarity, cell available deassertion time 3.10 Transmit FIFO Features * * * * Storage capacity for four cells or 256 bytes of packet data per port Programmable port address Programmable fill level thresholds Underflow and overflow status indications 3.11 Transmit Cell Processor Features * * * * * * * * * Programmable fill cell type HEC calculation and insertion/overwrite, including coset addition Cell scrambling using the self-synchronizing scrambler (x43+1) for ATM over DS3/E3 Distributed Sample Scrambler (DSS) for clear-channel ATM (cell-based physical layer) Single-bit and multiple-bit header error insertion for diagnostics Controls include enables/disables/settings for: cell processing, HEC insertion, coset polynomial addition, cell scrambling, fill cell type, error insertion type/rate/count, HEC bit corruption Counter for number of cells read from the transmit FIFO Cell mapping into the DS3/E3 frame, the PLCP frame, an externally defined frame, or the entire line bandwidth Octet alignment option for externally defined frame formats 3.12 Transmit Packet Processor Features * * * * * * * * * FCS calculation (16-bit or 32-bit) and insertion/overwrite Programmable FCS error insertion for diagnostics Bit or octet stuffing Programmable inter-frame fill insertion (flags or all-ones) Automatic packet abort insertion Packet scrambling using the self-synchronizing scrambler (x43+1) Controls include enables/disables/settings for: packet processing, FCS insertion or overwrite, 16/32-bit FCS, inter-frame fill type/length, scrambling, FCS error insertion type/rate/count Counters for number of packets and bytes read from the transmit FIFO Octet alignment with octet stuffing option for externally defined frame formats 19 DS3181/DS3182/DS3183/DS3184 3.13 Transmit PLCP Formatter Features * * * * * * * Insertion of FAS bytes (A1, A2), path overhead identification (POI) bytes, and path overhead bytes Generation of BIP-8 (B1), FEBE and RAI (G1) C1 cycle/stuff counter generation referenced to GPIO4 input pin, referenced to the received PLCP timing, or based on an 8 kHz division of one of the clock sources Automatic or manual insertion of FAS errors, BIP-8 errors All path overhead fields can be sourced from the PLCP transmit overhead port HDLC port for data link messages on F1, M1 or M2 bytes Trail Trace port for trace messages on F1 byte 3.14 Transmit DS3/E3 Formatter Features * * * * * * * * * * * * Insertion of framing overhead for M23 or C-bit parity DS3, or G.751 E3 or G.832 E3 B3ZS/HDB3 encoding Generation of RDI, AIS, and DS3 idle signal Automatic or manual insertion of bipolar violations (BPVs), excessive zeroes (EXZ) occurrences, F-bit errors, M-bit errors, FAS errors, P-bit parity errors, CP-bit parity errors, BIP-8 errors, and far end block errors (FEBE) HDLC port for DS3 path maintenance data link (PMDL), G.751 national bit or G.832 NR or GC channels FEAC port for DS3 FEAC channel can be configured to send one codeword, one codeword continuously, or two different code words back-to-back to send DS3 Line Loopback commands 16-byte Trail Trace Buffer port for the G.832 trail access point identifier Insertion of G.832 payload type, and timing marker bits from registers DS3 M23 C bits configurable as payload or overhead; as overhead they can be controlled from registers or the transmit overhead port Most framing overhead fields can be sourced from transmit overhead port Formatter bypass mode for clear-channel or externally defined format applications Support for subrate DS3/E3, internally or externally controlled (Fractional DS3/E3) 3.15 Transmit DS3/E3/STS-1 LIU Features * * * * * Wide 50+20% transmit clock duty cycle Line Build-Out (LBO) control Tri-state line driver outputs support protection switching applications Per-channel power-down control Output driver monitor status indication 3.16 Jitter Attenuator Features * * * * Fully integrated and requiring no external components Can be placed in transmit or receive path FIFO depth of 16 bits Standard compliant transmission jitter and wander 3.17 Clock Rate Adapter Features * * * * * Generation of the internally needed DS3 (44.736 MHz), E3 (34.368 MHz), and STS-1 (51.84 MHz) clocks a from single input reference clock Input reference clock can be 51.84 MHz, 44.736MHz or 34.368 MHz Internally derived clocks can be used as references for LIU and jitter attenuator Derived clocks can be transmitted off-chip for external system use Standards compliant jitter and wander requirements. 3.18 HDLC Overhead Controller Features * * * * Each port has a dedicated HDLC controller for DS3/E3 framer or PLCP link management 256-byte receive and transmit FIFOs Handles all of the normal Layer 2 tasks including zero stuffing/destuffing, FCS generation/checking, abort generation/checking, flag generation/detection, and byte alignment Programmable high and low water marks for the transmit and receive FIFOs 20 DS3181/DS3182/DS3183/DS3184 * * Terminates the Path Maintenance Data Link in DS3 C-bit Parity mode and optionally the G.751 Sn bit or the G.832 NR or GC channels or PLCP F1, M1 or M2 bytes RX data is forced to all ones during LOS, LOF and AIS detection to eliminate false packets 3.19 FEAC Controller Features * * * * * Each port has a dedicated FEAC controller for DS3/E3 link management Designed to handle multiple FEAC code words without Host intervention Receive FEAC automatically validates incoming code words and stores them in a 4-byte FIFO Transmit FEAC can be configured to send one codeword, one codeword continuously, or two different code words back-to-back to send DS3 Line Loopback commands Terminates the FEAC channel in DS3 C-Bit Parity mode and optionally the Sn bit in E3 mode 3.20 Trail Trace Buffer Features * * * * Each port has a dedicated Trail Trace Buffer for E3-G.832 or DS3/E3 PLCP link management Extraction and storage of the incoming G.832 or PLCP trail access point identifier in a 16-byte receive register Insertion of the outgoing trail access point identifier from a 16-byte transmit register Receive trace identifier unstable status indication 3.21 Bit Error Rate Tester (BERT) Features * * * * * Each port has a dedicated BERT tester Generation and detection of pseudo-random patterns and repetitive patterns from 1 to 32 bits in length Pattern insertion/extraction in PLCP payload, DS3/E3 payload, DS3/E3 fractional payload or entire data stream to and from the line interface Large 24-bit error counter allows testing to proceed for long periods without host intervention Errors can be inserted in the generated BERT patterns for diagnostic purposes (single bit errors or specific biterror rates) 3.22 Loopback Features * * * * * * Analog interface loopback - ALB (transmit to receive) Line facility loopback - LLB (receive to transmit) with optional transmission of unframed all-one AIS payload toward system/trunk interface Framer diagnostic loopback - DLB (transmit to receive) with automatic transmission of DS3 AIS or unframed all-one AIS signal toward line/tributary interface(s) DS3/E3 framer payload loopback - PLB (receive to transmit) with optional transmission of unframed all-one AIS payload toward system/trunk interface System interface loopback - SLB (transmit to receive) Simultaneous line facility loopback and framer diagnostic loopback 3.23 Microprocessor Interface Features * * * * * * * * Multiplexed or non-multiplexed address bus modes 8 or 16-bit data bus modes Byte swapping option in 16-bit data bus mode Read/Write and Data Strobe modes Ready handshake output signal Global reset input pin Global interrupt output pin Two programmable I/O pins per port 3.24 Subrate Features (Fractional DS3/E3) * * * * Independent per-port built-in support for subrate DS3 or E3 Independent subrate operation for both RX and TX data paths Subrate operation for each channel is totally independent from the other channels' operation, i.e. all subrate functions within the device are mutually exclusive Three distinct subrate algorithms: 21 DS3181/DS3182/DS3183/DS3184 * * * (FFRAC) Externally controlled with DS3 or E3 payload manipulating capability * (XFRAC) Externally controlled with flexible DS3 or E3 data rate reduction capability * (IFRAC) Internally controlled with simple DS3 or E3 data rate reduction capability Subrate algorithm selection is on per-port basis Internal subrate mechanism allows down to bit-level granularity of the DS3 or E3 payload 3.25 Test Features * * * * * * Five pin JTAG port All functional pins are in/out pins in JTAG mode Standard JTAG instructions: SAMPLE/PRELOAD, BYPASS, EXTEST, CLAMP, HIGHZ, IDCODE RAM BIST on all internal RAM High-Z pin to force all digital output and in/out pins into HIZ TEST pin for manufacturing scan test modes 22 DS3181/DS3182/DS3183/DS3184 4 STANDARDS COMPLIANCE Table 4-1. Standards Compliance SPECIFICATION SPECIFICATION TITLE ANSI T1.102-1993 T1.107-1995 T1.231-1997 T1.404-1994 T1.646-1995 Digital Hierarchy - Electrical Interfaces Digital Hierarchy - Formats Specification Digital Hierarchy - Layer 1 In-Service Digital Transmission Performance Monitoring Network-to-Customer Installation - DS3 Metallic Interface Specification Broadband ISDN - Physical Layer Specification for User-Network Interfaces Including DS1/ATM ATM FORUM af-phy-0034.000 af-phy-0039.000 af-phy-0043.000 af-phy-0054.000 af-phy-0136.000 af-phy-0143.000 af-bici-0013.003 E3 Public UNI, August, 1995 UTOPIA Level 2, Version 1.0, June, 1995 A Cell-Based Transmission Convergence Sublayer for Clear-Channel Interfaces, November, 1995 DS3 Physical Layer Interface Specification, January, 1996 UTOPIA L3 Physical Layer Interface, November, 1999 Frame-based ATM Interface (Level 3), March, 2000 BISDN Inter Carrier Interface (B-ICI) Specification Version 2.0 (Integrated), December, 1995 ETSI ETS 300 686 ETS 300 337 ETS EN 300 689 ETS 300 689 Business TeleCommunications; 34Mbps and 140Mbits/s digital leased lines (D34U, D34S, D140U and D140S); Network interface presentation, 1996 Transmission and Multiplexing (TM); Generic frame structures for the transport of various signals (including Asynchronous Transfer Mode (ATM) cells and Synchronous Digital Hierarchy (SDH) elements) at the ITU-T Recommendation G.702 hierarchical rates of 2 048 kbit/s, 34 368 kbit/s and 139 264 kbit/s, Second Edition, June, 1997 Access and Terminals (AT); 34Mbps Digital Leased Lines (D34U and D34S); Terminal equipment interface, July 2001 Business TeleCommunications (BTC); 34 Mbps digital leased lines (D34U and D34S), Terminal equipment interface, V 1.2.1, 2001-07 IETF RFC 1661 RFC 1662 RFC 2496 The Point-to-Point Protocol (PPP), July, 1994 PPP in HDLC-like Framing, July, 1994 Definition of Managed Objects for the DS3/E3 Interface Type, January, 1999 ISO ISO 3309:1993 Information Technology - Telecommunications & information exchange between systems - High Level Data Link Control (HDLC) procedures - Frame structure, Fifth Edition, 1993 ITU-T G.703 G.704 G.751 G.775 G.804 G.823 G.824 Physical/Electrical Characteristics of Hierarchical Digital Interfaces, 1991 Synchronous Frame Structures Used at 1544, 6312, 2048, 8488 and 44 736 kbit/s Hierarchical Levels, July, 1995 Digital Multiplex Equipment Operating at the Third Order Bit Rate of 34,368 kbit/s and the Fourth Order bit Rate of 139,264 kbit/s and Using Positive Justification, 1993 Loss Of Signal (LOS) and Alarm Indication Signal (AIS) Defect Detection and Clearance Criteria, November, 1994 ATM Cell Mapping Into Plesiochronous Digital Hierarchy (PDH), November, 1993 The Control of Jitter and Wander Within Digital Networks Which are Based on the 2048 kbit/s Hierarchy, 1993 The Control of Jitter and Wander within Digital Networks that are Based on the 1544kbps 23 DS3181/DS3182/DS3183/DS3184 SPECIFICATION G.832 I.432 O.151 Q.921 SPECIFICATION TITLE Hierarchy, 1993 Transport of SDH Elements on PDH Networks - Frame and Multiplexing Structures, November, 1995 B-ISDN User-Network Interface - Physical Layer Specification, March, 1993 Error Performance Measuring Equipment Operating at the Primary Rate and Above, October, 1992 ISDN User-Network Interface - Data Link Layer Specification, March 1993 OIF OIF-SPI3-01.0 System Packet Interface Level 3 (SPI-3): OC-48 System Interface for Physical and Link Layer Devices SATURN(R) GROUP POS-PHY L2 POS-PHY L3 POS-PHY Level 2 Packet Over SONET Interface Specification for Physical Layer Devices, December, 1998 POS-PHY Level 3 Packet Over SONET Interface Specification for Physical and Link Layer Devices, June, 2000 TELCORDIA GR-253-CORE GR-499-CORE GR-820-CORE SONET Transport Systems: Common Generic Criteria, Issue 2, December 1995 Transport Systems Generic Requirements (TSGR): Common Requirements, Issue 2, December 1998 Generic Digital Transmission Surveillance, Issue 1, November 1994 IEEE IEEE Std 11491990 IEEE Standard Test Access Port and Boundary-Scan Architecture, (Includes IEEE Std 1149-1993) October 21, 1993 SATURN is a registered trademark of PMC-Sierra, Inc. 24 DS3181/DS3182/DS3183/DS3184 5 ACRONYMS AND GLOSSARY Definition of the terms used in this data sheet: Acronyms * * * * * * * * * * * * * ATM - Asynchronous Transfer Mode CC52 - Clear-Channel 52 Mbps (STS-1 Clock Rate) CLAD - Clock Rate Adapter CLR - Clear-Channel Mode DSS - Distributed Sample Scrambler FFRAC - Flexible Fractional Mode FRM - Frame Mode HDLC - High Level Data Link Control IFRAC - Internal Fractional Mode OHM - Overhead Mask mode (LIU disabled) for externally defined framing PLCP - Physical Layer Convergence Protocol SPI-3 - same as POS-PHY L3 XFRAC - External Fractional Mode Glossary * Cell - ATM cell * Clear-Channel - A datastream with no framing included * Fractional - Uses only a portion of available payload for data, also known as subrate * Octet Aligned - Byte aligned * Packet - HDLC packet * Subrate - See Fractional * Unchannelized - See Clear-Channel 25 DS3181/DS3182/DS3183/DS3184 6 MAJOR OPERATIONAL MODES The major operational modes are determined by the FM[5:0] framer mode bits and a few other control bits. Unused features are powered down and the data paths are held in reset. The configuration registers of the unused features can be written to and read from. The function of some IO pins change in different operational modes. The line interface operational mode is determined by the LM[2:0] bits. 6.1 DS3/E3 ATM/Packet Mode DS3/E3 ATM/Packet mode is a normal mode of operation for the DS318x device, which maps/demaps ATM cells or packet data into a DS3 or E3 data stream via the selected mapping mode. Major functional blocks for the DS3/E3 ATM/Packet mode are shown in Figure 6-1. Mapping configuration is programmable on per-port basis and is shown in Table 6-1. Table 6-1. DS3/E3 ATM/Packet Mode Configuration Registers FM[5:0] SIM[1:0] GL.CR1 PMCPE PORT.CR2 UTOPIA L2 ATM 0XX000 00 X UTOPIA L3 ATM 0XX000 01 X POS-PHY L2 ATM 0XX000 10 1 POS-PHY L3 ATM 0XX000 11 1 POS-PHY L2 Packet 0XX000 10 0 POS-PHY L3 Packet 0XX000 11 0 MODE TCLKOn/ TGCLKn TCLKIn TSOFIn TOHENn TOHn TOHCLKn TOHSOFn Figure 6-1. DS3/E3 ATM/Packet Mode TAIS TPOSn/ TDATn TUA1 CLKC CLKB CLKA Clock Rate Adapter B3ZS/ HDB3 Decoder System Interface SLB TX BERT HDLC RX BERT Rx Packet Processor DS3 / E3 Receive Framer Rx Cell Processor UA1 GEN IEEE P1149.1 JTAG Test Access Port 26 Rx FIFO Microprocessor Interface RST DS3/E3 Receive LIU RXPn RXNn Trail FEAC Trace Buffer PLB LLB ALB RLCLKn RPOSn/ RDATn RNEGn/ RLCVn/ ROHMIn RCLKOn/ RGCLKn TXNn Tx FIFO Tx Packet Processor ROHn ROHCLKn ROHSOFn DS3/E3 Transmit LIU TXPn Tx Cell Processor DS3 / E3 Transmit Formatter B3ZS/ HDB3 Encoder DLB TNEGn/ TOHMOn/ TLCLKn n = port # (1-4) DS3181/DS3182/DS3183/DS3184 6.2 DS3/E3 ATM/Packet--OHM Mode DS3/E3 ATM/Packet--OHM Mode is a normal mode of operation for the DS318x devices, which maps/demaps ATM cells or packet data into a DS3 or E3 data stream, supporting externally defined framing protocols. Major functional blocks for the DS3/E3 ATM/Packet--OHM Mode are shown in Figure 6-2. Mapping configuration is programmable on per-port basis and is shown in Table 6-2. Table 6-2. DS3/E3 ATM/Packet--OHM Mode Configuration Registers FM[5:0] SIM[1:0] GL.CR1 PMCPE PORT.CR2 UTOPIA L2 ATM 0XX001 00 X UTOPIA L3 ATM 0XX001 01 X POS-PHY L2 ATM 0XX001 10 1 POS-PHY L3 ATM 0XX001 11 1 POS-PHY L2 Packet 0XX001 10 0 POS-PHY L3 Packet 0XX001 11 0 MODE TCLKOn/TGCLKn TCLKIn TOHENn TOHn TOHCLKn TOHSOFn Figure 6-2. DS3/E3 ATM/Packet--OHM Mode TOHMIn TUA1 Tx Cell Processor DS3/E3 Transmit Formatter TOHMOn LLB DLB Analog Loopback TLCLKn Tx FIFO Tx Packet Processor TX BERT TRAIL HDLC FEAC TRACE SLB TDATn RX BERT Tx Packet Processor DS3/E3 Receive Framer RLCLKn RDATn IEEE 1149.1 JTAG Test Access Port UA1 GEN RCLKOn/RGCLKn 27 RST Microprocessor Interface ROHn ROHCLKn ROHSOFn CLKB CLKC CLKA System Interface Rx Cell Processor ROHMIn Clock Rate Adapter Rx FIFO n = port # (1-4) DS3181/DS3182/DS3183/DS3184 6.3 DS3/E3 Internal Fractional (Subrate) ATM/Packet Mode DS3/E3 Internal Fractional Mode allows subrate datastreams to be inserted into a DS3 or E3 line, with the fractional overhead internally controlled. Major functional blocks for the DS3/E3 Internal Fractional Mode are shown in Figure 6-3. Mapping configuration is programmable on per-port basis and is shown in Table 6-3. The "-OHM" modes are not allowed in fractional framing modes since the user is not able to distinguish between internal framing overhead and external framing overhead bit locations. Table 6-3. DS3/E3 Internal Fractional (IFRAC) ATM/Packet Mode Configuration Registers FM[5:0] SIM[1:0] GL.CR1 PMCPE PORT.CR2 UTOPIA L2 ATM 0XX010 00 X UTOPIA L3 ATM 0XX010 01 X POS-PHY L2 ATM 0XX010 10 1 POS-PHY L3 ATM 0XX010 11 1 POS-PHY L2 Packet 0XX010 10 0 POS-PHY L3 Packet 0XX010 11 0 MODE TFOHENOn TFOHn TCLKIn TCLKOn/TGCLKn TOHENn TOHn TOHCLKn TOHSOFn TOHMIn/TSOFIn Figure 6-3. DS3/E3 Internal Fractional ATM/Packet Mode TAIS TPOSn/ TDATn TUA1 System Interface SLB RX BERT Rx Packet Processor DS3 / E3 Receive Framer RX FRAC Rx Cell Processor UA1 GEN 28 Rx FIFO Microprocessor Interface RST IEEE P1149.1 JTAG Test Access Port RCLKOn/RGCLKn CLKC CLKB CLKA Clock Rate Adapter B3ZS/ HDB3 Decoder TX BERT HDLC RSERn DS3/E3 Receive LIU RXPn RXNn Trail FEAC Trace Buffer RFOHENOn LLB ALB RLCLKn RPOSn/ RDATn RNEGn/ RLCVn/ ROHMIn Tx FIFO Tx Packet Processor TX FRAC PLB TXNn ROHn ROHCLKn ROHSOFn TXPn Tx Cell Processor DS3 / E3 Transmit Formatter B3ZS/ HDB3 Encoder DS3/E3 Transmit LIU DLB TNEGn/ TOHMOn/ TLCLKn n = port # (1-4) DS3181/DS3182/DS3183/DS3184 6.4 DS3/E3 External Fractional (Subrate) ATM/Packet Mode DS3/E3 External Fractional Mode allows subrate datastreams to be inserted into a DS3 or E3 line, with the fractional overhead externally controlled. Major functional blocks for the DS3/E3 Internal Fractional Mode are shown in Figure 6-4. Mapping configuration is programmable on per-port basis and is shown in Table 6-4. The "-OHM" modes are not allowed in fractional framing modes since the user cannot distinguish between internal framing overhead and external framing overhead bit locations. Table 6-4. DS3/E3 External Fractional (XFRAC) ATM/Packet Mode Configuration Registers FM[5:0] SIM[1:0] GL.CR1 PMCPE PORT.CR2 UTOPIA L2 ATM 0XX011 00 X UTOPIA L3 ATM 0XX011 01 X POS-PHY L2 ATM 0XX011 10 1 POS-PHY L3 ATM 0XX011 11 1 POS-PHY L2 Packet 0XX011 10 0 POS-PHY L3 Packet 0XX011 11 0 MODE TFOHENOn TFOHENIn TFOHn TCLKIn TCLKOn/TGCLKn TOHENn TOHn TOHCLKn TOHSOFn TOHMIn/TSOFIn Figure 6-4. DS3/E3 External Fractional ATM/Packet Mode TAIS TPOSn/ TDATn TUA1 CLKC CLKB CLKA Clock Rate Adapter B3ZS/ HDB3 Decoder System Interface SLB TX BERT HDLC RX BERT Rx Packet Processor DS3 / E3 Receive Framer RX FRAC Rx Cell Processor UA1 GEN IEEE P1149.1 JTAG Test Access Port 29 Rx FIFO Microprocessor Interface RST DS3/E3 Receive LIU RXPn RXNn Trail FEAC Trace Buffer RSERn RSOFOn/RDENn RCLKOn/RGCLKn RFOHENIn LLB ALB RLCLKn RPOSn/ RDATn RNEGn/ RLCVn/ ROHMIn PLB TXNn Tx FIFO Tx Packet Processor TX FRAC ROHn ROHCLKn ROHSOFn DS3/E3 Transmit LIU TXPn Tx Cell Processor DS3 / E3 Transmit Formatter B3ZS/ HDB3 Encoder DLB TNEGn/ TOHMOn/ TLCLKn n = port # (1-4) DS3181/DS3182/DS3183/DS3184 6.5 DS3/E3 Flexible External Fractional (Subrate) Mode Configuration Mode DS3/E3 Flexible External Fractional Mode allows subrate datastreams to be inserted into a DS3 or E3 line, with the fractional overhead and payload externally multiplexed. Major functional blocks for the DS3/E3 Flexible External Fractional Mode are shown in Figure 6-5. Mapping configuration is programmable on per-port basis and is shown in Table 6-5. The "-OHM" modes are not allowed in fractional framing modes since the user cannot distinguish between internal framing overhead and external framing overhead bit locations. Table 6-5. DS3/E3 Flexible External Fractional (Subrate) Mode Configuration Registers FM[5:0] SIM[1:0] GL.CR1 PMCPE PORT.CR2 UTOPIA L2 ATM 0XX110 00 X UTOPIA L3 ATM 0XX110 01 X POS-PHY L2 ATM 0XX110 10 1 POS-PHY L3 ATM 0XX110 11 1 POS-PHY L2 Packet 0XX110 10 0 POS-PHY L3 Packet 0XX110 11 0 MODE TPDENIn TPDENOn TPDATn TCLKOn/ TGCLKn TSERn TSOFOn/TDENn TCLKIn TOHENn TOHn TOHCLKn TOHSOFn TSOFIn Figure 6-5. DS3/E3 Flexible External Fractional Mode TAIS TUA1 TNEGn/ TOHMOn TLCLKn LLB ALB RLCLKn RPOSn/ RDATn RNEGn/ RLCVn/ ROHMIn Tx FIFO Tx Packet Processor TX BERT Trail FEAC Trace HDLC Buffer Rx Packet Processor DS3 / E3 Receive Framer Rx FIFO Rx Cell Processor UA1 GEN 30 RST* RPDATn Microprocessor Interface RPDENIn IEEE P1149.1 JTAG Test Access Port RSERn RSOFOn/RDENn RCLKOn/RGCLKn CLKC CLKB CLKA Clock Rate Adapter B3ZS/ HDB3 Decoder ROHn ROHCLKn ROHSOFn DS3/E3 Receive LIU RXPn RXNn System Interface RX BERT PLB TXNn DLB DS3/E3 Transmit LIU TXPn Tx Cell Processor DS3 / E3 Transmit Formatter B3ZS/ HDB3 Encoder SLB TPOSn/ TDATn n = port # (1-4) DS3181/DS3182/DS3183/DS3184 6.6 DS3/E3 G.751 PLCP ATM Mode DS3/E3 G.751 PLCP ATM mode is a normal mode of operation for the DS318x devices, which maps/demaps ATM cells into/from the DS3/E3 PLCP data stream. Major functional blocks for the DS3/E3 ATM/Packet mode are shown in Figure 6-6. Mapping configuration is programmable on per-port basis and is shown in Table 6-6. The PMCPE configuration bit is ignored when in PLCP mode and ATM cell processing is forced. Table 6-6. DS3/E3 G.751 PLCP ATM Mode Configuration Registers FM[5:0] SIM[1:0] GL.CR1 PMCPE PORT.CR2 UTOPIA L2 ATM 0XX100 00 X UTOPIA L3 ATM 0XX100 01 X POS-PHY L2 ATM 0XX100 10 1 POS-PHY L3 ATM 0XX100 11 1 POS-PHY L2 Packet 0XX100 10 0 POS-PHY L3 Packet 0XX100 11 0 MODE TPOHn TPOHENn TPOHSOFn TCLKIn TOHENn TOHn TOHCLKn TOHSOFn TSOFIn Figure 6-6. DS3/E3 G.751 PLCP ATM Mode TAIS TPOSn/ TDATn TUA1 CLKC CLKB CLKA Clock Rate Adapter B3ZS/ HDB3 Decoder DS3 / E3 Receive Framer TX BERT TRAIL TRACE RX BERT RX PLCP UA1 GEN IEEE 1149.1 JTAG Test Access Port 31 Tx FIFO System Interface SLB HDLC Rx Cell Processor Rx FIFO Microprocessor Interface RST DS3/E3 Receive LIU RXPn RXNn FEAC RPOHn RPOHSOFn RPOHCLKn/RCLKOn LLB ALB RLCLKn RPOSn/ RDATn RNEGn/ RLCVn/ ROHMIn PLB TXNn Tx Cell Processor TX PLCP ROHn ROHCLKn ROHSOFn TXPn DS3 / E3 Transmit Formatter B3ZS/ HDB3 Encoder DS3/E3 Transmit LIU DLB TNEGn/ TOHMOn/ TLCLKn n = port # (1-4) DS3181/DS3182/DS3183/DS3184 6.7 DS3/E3 G.751 PLCP ATM--OHM Mode DS3/E3 G.751 PLCP ATM--OHM mode is a normal mode of operation for the DS318x devices, which maps/demaps ATM cells into/from the DS3/E3 PLCP data stream, supporting externally defined framing modes. Major functional blocks for the DS3/E3 G.751 PLCP ATM--OHM mode are shown in Figure 6-7. Mapping configuration is programmable on per-port basis and is shown in Table 6-7. The PMCPE configuration bit is ignored when in PLCP mode and ATM cell processing is forced. Table 6-7. DS3/E3 G.751 PLCP ATM--OHM Mode Configuration Registers FM[5:0] SIM[1:0] PMCPE PORT.CR2 DS3 UTOPIA L2 ATM 0XX101 00 X DS3 UTOPIA L3 ATM 0XX101 01 X DS3 POS-PHY L2 ATM 0XX101 10 X DS3 POS-PHY L3 ATM 0XX101 11 X E3 G.751 UTOPIA L2 ATM 010101 00 X E3 G.751 UTOPIA L3 ATM 010101 01 X E3 G.751 POS-PHY L2 ATM 010101 10 X E3 G.751 POS-PHY L3 ATM 010101 11 X MODE 32 DS3181/DS3182/DS3183/DS3184 TOHMIn TPOHn TPOHENn TPOHSOFn TPOHCLKn/ TCLKOn TCLKIn TOHENn TOHn TOHCLKn TOHSOFn Figure 6-7. DS3/E3 G.751 PLCP ATM--OHM Mode TUA1 Tx Cell Processor DS3/E3 Transmit Formatter TOHMOn LLB RLCLKn DLB Analog Loopback TLCLKn UA1 GEN IEEE 1149.1 JTAG Test Access Port 33 Rx Cell Processor Rx FIFO Microprocessor Interface RPOHn RPOHCLKn/RCLKOn RPOHSOFn CLKB CLKC CLKA Clock Rate Adapter System Interface RX BERT RX PLCP ROHn ROHCLKn ROHSOFn ROHMIn TX BERT TRAIL TRACE FEAC HDLC DS3/E3 Receive Framer RDATn Tx FIFO TX PLCP SLB TDATn n = port # (1-4) DS3181/DS3182/DS3183/DS3184 6.8 Clear-Channel ATM/Packet Mode The Clear-Channel ATM/Packet Mode maps/demaps ATM cells or HDLC packets into/from a serial datastream, bypassing the DS3/E3 formatter/framer. Major functional blocks for the Clear-Channel ATM/Packet Mode are shown in Figure 6-8. Mapping configuration is programmable on per-port basis and is shown in Table 6-8. Table 6-8. Clear-Channel ATM/Packet Mode Configuration Modes FM[5:0] SIM[1:0] GL.CR1 PMCPE PORT.CR2 UTOPIA L2 ATM 1XX0X0 00 X UTOPIA L3 ATM 1XX0X0 01 X POS-PHY L2 ATM 1XX0X0 10 1 POS-PHY L3 ATM 1XX0X0 11 1 POS-PHY L2 Packet 1XX0X0 10 0 POS-PHY L3 Packet 1XX0X0 11 0 MODE TCLKIn TCLKOn/ TGCLKn Figure 6-8. Clear-Channel ATM/Packet Modes TAIS TPOSn/ TDATn TUA1 TXNn Tx Packet Processor RX BERT Rx Packet Processor B3ZS/ HDB3 Decoder Rx Cell Processor UA1 GEN RCLKOn/ RGCLKn 34 Rx FIFO Microprocessor Interface RST IEEE P1149.1 JTAG Test Access Port CLKC CLKB CLKA Clock Rate Adapter PLB LLB ALB DS3/E3 Receive LIU RXPn RXNn DLB TX BERT RLCLKn RPOSn/ RDATn RNEGn/ RLCVn/ ROHMIn Tx FIFO System Interface TXPn Tx Cell Processor B3ZS/ HDB3 Encoder DS3/E3 Transmit LIU SLB TNEGn/ TOHMOn/ TLCLKn n = port # (1-4) DS3181/DS3182/DS3183/DS3184 6.9 Clear-Channel ATM/Packet--OHM Mode The Clear-Channel ATM/Packet--OHM Mode maps/demaps ATM cells or HDLC packets into/from a serial datastream, bypassing both the DS3/E3 formatter/framer and the LIU, supporting externally defined framing modes. Major functional blocks for the Clear-Channel ATM/Packet--OHM Mode are shown in Figure 6-9. Mapping configuration is programmable on per-port basis and is shown in Table 6-9. Table 6-9. Clear-Channel ATM/Packet--OHM Mode Configuration Registers FM[5:0] SIM[1:0] GL.CR1 PMCPE PORT.CR2 UTOPIA L2 ATM 1XX001 00 X UTOPIA L3 ATM 1XX001 01 X POS-PHY L2 ATM 1XX001 10 1 POS-PHY L3 ATM 1XX001 11 1 POS-PHY L2 Packet 1XX001 10 0 POS-PHY L3 Packet 1XX001 11 0 MODE TOHMIn TCLKOn TCLKIn Figure 6-9. Clear-Channel ATM/Packet--OHM Mode TUA1 Tx Cell Processor TDATn TOHMOn Tx FIFO Tx Packet Processor Analog Loopback TLCLKn SLB LLB DLB RX BERT Rx Packet Processor RLCLKn RDATn Rx Cell Processor ROHMIn Rx FIFO Microprocessor Interface UA1 GEN 35 RST IEEE 1149.1 JTAG Test Access Port RCLKOn CLKB CLKC Clock Rate Adapter CLKA System Interface TX BERT n = port # (1-4) DS3181/DS3182/DS3183/DS3184 6.10 Clear-Channel Octet Aligned ATM/Packet--OHM Mode The Clear-Channel Octet Aligned ATM/Packet--OHM Mode maps/demaps ATM cells or HDLC packets into/from a serial datastream, bypassing both the DS3/E3 formatter/framer and the LIU, supporting arbitrary framing modes. Major functional blocks for the Clear-Channel Octet Aligned ATM/Packet--OHM Mode are shown in Figure 6-10. Mapping configuration is programmable on per-port basis and is shown in Table 6-10. Table 6-10. Clear-Channel Octet Aligned ATM/Packet--OHM Mode Configuration Registers FM[5:0] SIM[1:0] GL.CR1 PMCPE PORT.CR2 UTOPIA L2 ATM 1XX011 00 X UTOPIA L3 ATM 1XX011 01 X POS-PHY L2 ATM 1XX011 10 1 POS-PHY L3 ATM 1XX011 11 1 POS-PHY L2 Packet 1XX011 10 0 POS-PHY L3 Packet 1XX011 11 0 MODE TCLKOn TCLKIn Figure 6-10. Clear-Channel Octet Aligned ATM/Packet--OHM Mode TUA1 TOHMIn Parallel to Serial TDATn TOHMOn Tx Cell Processor Tx FIFO Tx Packet Processor Analog Loopback TLCLKn System Interface SLB DLB LLB TX BERT RX BERT Rx Packet Processor RLCLKn Serial to Parallel RDATn ROHMIn Rx FIFO Microprocessor Interface UA1 GEN 36 RST IEEE 1149.1 JTAG Test Access Port RCLKOn CLKB CLKC CLKA Clock Rate Adapter Rx Cell Processor n = port # (1-4) DS3181/DS3182/DS3183/DS3184 7 MAJOR LINE INTERFACE OPERATING MODES The line interface modes provide the following functions: 1. Enabling/disabling of RX and TX LIU. 2. Enabling/Disabling of jitter attenuator (JA). 3. Selection of the location of JA, i.e., RX or TX path. 4. Selection of the line coding type, i.e., B3ZS/HDB3/AMI or UNI. 7.1 DS3HDB3/B3ZS/AMI LIU Mode When the "- OHM" framing modes are enabled, the line interface is forced into the unipolar (UNI) mode. The TZCDS and RZCDS bits in the line encoder/decoder block select between no encoding/decoding (AMI) and encoding/decoding (B3ZS, HDB3). When the HDB3/B3ZS line decoder/encoder is enabled, the framing modes (FM bits) select between B3ZS and HDB3 line coding. DS3 and CC52 frame modes select the B3ZS line code while the E3 modes select the HDB3 line code. Table 7-1. HDB3/B3ZS/AMI LIU Mode Configuration Registers LM[2:0] LINE.TCR.TZSD AND LINE.RCR.RZSD TLEN PORT.CR2 JA Off, B3ZS or HDB3 001 0 0 JA RX, B3ZS or HDB3 010 0 0 JA TX, B3ZS or HDB3 011 0 0 JA Off, AMI 001 1 0 JA RX, AMI 010 1 0 JA TX, AMI 011 1 0 MODE 37 DS3181/DS3182/DS3183/DS3184 Figure 7-1. HDB3/B3ZS/AMI LIU Mode TAIS TUA1 LLB ALB TXNn B3ZS/ HDB3 Encoder DS3/E3 Transmit LIU DS3/E3 Receive LIU RXPn RXNn FROM FRAMING LOGIC OR EXTERNAL PINS DLB TXPn B3ZS/ HDB3 Decoder TO FRAMING LOGIC OR EXTERNAL PINS CLKB n = port # (1-4) CLKC CLKA Clock Rate Adapter 38 DS3181/DS3182/DS3183/DS3184 7.2 HDB3/B3ZS/AMI Non-LIU Line Interface Mode The Non-LIU Line Interface Mode disables the LIU and a digital representation of AMI is output/input on the TPOSn/TNEGn signals and the RPOSn/RNEGn signals. Selection between AMI and HDB3/B3ZS is made via the LINE.TCR Register. HDB3 and B3ZS selection is controlled by the configuration selected by the FM bits. DS3 and CC52 frame modes select the B3ZS line code while the E3 modes select the HDB3 line code. The DS3AIS signal can only be generated in non-OHM DS3 modes. Table 7-2. HDB3/B3ZS/AMI Non-LIU Mode Configuration Registers MODE LM[2:0] LINE.TCR.TZSD AND LINE.RCR.RZSD TLEN PORT.CR2 LIU Off, B3ZS or HDB3 000 0 1 LIU Off, AMI 000 1 1 Figure 7-2. HDB3/B3ZS/AMI Non-LIU Line Interface Mode TAIS TUA1 B3ZS/ HDB3 Encoder B3ZS/ HDB3 Decoder RLCLKn RPOSn RNEGn FROM FRAMING LOGIC OR EXTERNAL PINS DLB LLB ALB TPOSn TNEGn TLCLKn TO FRAMING LOGIC OR EXTERNAL PINS CLKB n = port # (1-4) CLKC CLKA Clock Rate Adapter 39 DS3181/DS3182/DS3183/DS3184 7.3 UNI Line Interface Mode This mode is valid for all framing modes, providing a digital NRZ input/output on RDATn and TDATn and clocked by RLCLKn and TLCLKn. The B3ZS/HDB3 decoder/encoder block is disabled except for the BPV counter, which is used to count RLCV errors. Table 7-3. UNI Line Interface Mode Configuration Registers MODE LM[2:0] LINE.TCR.TZSD AND LINE.RCR.RZSD TLEN PORT.CR2 1XX X 1 Unipolar Mode Figure 7-3. UNI Line Interface Mode TUA1 FROM FRAMING LOGIC OR EXTERNAL PINS TDATn LLB ALB RLCLKn DLB TLCLKn TO FRAMING LOGIC OR EXTERNAL PINS RDATn CLKB CLKC CLKA Clock Rate Adapter n = port # (1-4) 40 DS3181/DS3182/DS3183/DS3184 7.4 UNI Line Interface--OHM Mode The line interface is forced into UNI mode when the framer is in any OHM mode; therefore, the LM bits are Don't Cares. This mode is the same as the UNI Line Interface Mode except that the OHM pins determine whether the data is payload or not. Table 7-4. UNI Line Interface--OHM Mode Configuration Registers FM[5:0] LM[2:0] LINE.TCR.TZSD AND LINE.RCR.RZSD TLEN PORT.CR2 DS3/E3 Overhead Mask Mode 0XXX01 XXX X 1 Clear-Channel Overhead Mask Mode 1XX0X1 XXX X 1 MODE Figure 7-4. UNI Line Interface--OHM Mode TOHMIn TUA1 TDATn FROM FRAMING LOGIC OR EXTERNAL PINS TOHMOn Line Loopback ALB RLCLKn Framer Diagnostic Loopback TLCLKn TO FRAMING LOGIC OR EXTERNAL PINS RDATn ROHMIn CLKB CLKC CLKA Clock Rate Adapter n = port # 41 DS3181/DS3182/DS3183/DS3184 8 PIN DESCRIPTIONS Note: In JTAG mode, all digital pins are bidirectional to increase the effectiveness of board-level ATPG patterns for isolation of interconnect failures. 8.1 Short Pin Descriptions Table 8-1. DS3184 Short Pin Descriptions n = 1,2,3,4 (port number). Ipu (input with pullup), Oz (output tri-stateable), (needs an external pullup or pulldown resistor to keep from floating), Oa (analog output), Ia (analog input), IO (bidirectional in/out). All unused input pins without pullup should be tied low. NAME TYPE FUNCTION PIN PORT 4 PORT 3 LINE IO Transmit Line Clock Output V11 C11 Transmit Positive AMI / Data V14 C14 Transmit Negative AMI / Line OH Mask W14 B14 Transmit Positive Analog W6 B6 Transmit Negative Analog Y6 A6 Receive Clock Input Y12 A12 Receive Positive Analog W5 B5 Receive Negative Analog Y5 A5 Positive AMI / Data W15 B15 Negative AMI / Line Code Violation / Line OH I Y15 A15 Mask Output DS3/E3 OVERHEAD INTERFACE TOHn I Transmit Overhead U11 D11 TOHENn I Transmit Overhead Enable T14 E14 TOHCLKn O Transmit Overhead Clock T11 E11 TOHSOFn O Transmit Overhead Start Of Frame T12 E12 ROHn O Receive Overhead T10 E10 ROHCLKn O Receive Overhead Clock T13 E13 ROHSOFn O Receive Overhead Start Of Frame U14 D14 DS3/E3 SERIAL DATA, PLCP AND FRACTIONAL DS3/E3 OVERHEAD INTERFACE TCLKIn I Transmit Line Clock Input Y14 A14 TSOFIn / TOHMIn I Transmit Start Of Frame Input / OH Mask Input U12 D12 TSERn/ TPOHn / Transmit Serial Data / PLCP Overhead / I V13 C13 TFOHn/ Fractional Overhead TPDENIn / Transmit Payload Data Enable Input / PLCP I U13 D13 TPOHENn / Overhead Enable / Fractional OH Enable Input TFOHENIn Transmit Clock Output / Gapped Clock / PLCP TCLKOn / TGCLKn / Y13 A13 O Overhead Clock TPOHCLKn TSOFOn / TDENn / Transmit Framer Start Of Frame / Data Enable / O V12 C12 TPOHSOFn / PLCP Overhead Start Of Frame / Fractional OH TFOHENOn Enable Output TPDENOn O Transmit Payload Data Enable Output W10 B10 TPDATn O Transmit Payload Data V10 C10 RPDENIn / Receive Payload Data Enable Input / Fractional I W13 B13 RFOHENIn Overhead Enable Input RPDATn I Receive Payload Data Y10 A10 RSERn / RPOHn O Receive Serial Data / PLCP Overhead W11 B11 RCLKOn / RGCLKn Receive / Clock Output / Gapped Clock / PLCP O Y11 A11 RPOHCLKn Overhead Clock TLCLKn TPOSn / TDATn TNEGn / TOHMOn TXPn TXNn RLCLKn RXPn RXNn RPOSn / RDATn RNEGn / RLCVn / ROHMIn O O O Oa Oa I Ia Ia I 42 PORT 2 PORT 1 Y8 V4 U4 M2 M1 W8 R2 R1 Y3 A8 C4 D4 J2 J1 B8 F2 F1 A3 W3 B3 U8 T5 V8 V7 U10 U5 Y2 D8 E5 C8 C7 D10 D5 B2 W4 W7 B4 B7 T6 E6 V5 C5 U7 D7 Y7 A7 Y9 W9 A9 B9 U6 D6 V9 T9 C9 E9 U9 D9 DS3181/DS3182/DS3183/DS3184 NAME TYPE FUNCTION RSOFOn / RDENn / RPOHSOFn / RFOHENOn O Receive Framer Start Of Frame / Data Enable / PLCP Overhead Start Of Frame / Fractional Overhead Enable Output NAME TYPE FUNCTION TSCLK TADR[4] TADR[3] TADR[2] TADR[1] TADR[0] TDATA[31] TDATA[30] TDATA[29] TDATA[28] TDATA[27] TDATA[26] TDATA[25] TDATA[24] TDATA[23] TDATA[22] TDATA[21] TDATA[20] TDATA[19] TDATA[18] TDATA[17] TDATA[16] TDATA[15] TDATA[14] TDATA[13] TDATA[12] TDATA[11] TDATA[10] TDATA[9] TDATA[8] TDATA[7] TDATA[6] TDATA[5] TDATA[4] TDATA[3] TDATA[2] TDATA[1] TDATA[0] TPRTY TEN TDXA[1]/TPXA TDXA[4] TDXA[3] TDXA[2] TSOX PIN PORT 4 PORT 3 PORT 2 PORT 1 W12 B12 T8 E8 UTOPIA L2/L3 OR POS-PHY L2/3 OR SPI-3 SYSTEM INTERFACE I Transmit System Clock I Transmit Address [4:0] I Transmit Data [31:0] I I Transmit Parity Transmit Enable (Active Low) Transmit Direct Cell/Packet Available [1] / Polled Cell/Packet Available (Tri-State) Oz O Transmit Direct Cell/Packet Available [4:2] I Transmit Start Of Cell/Packet 43 PIN J20 C15 D15 E15 A16 A18 U15 T15 U16 U17 D18 D17 C19 F20 E16 D16 C16 C18 C17 T17 T16 R17 V16 W17 Y18 V17 W18 W19 B19 C20 W20 U18 V18 V19 U19 V20 T18 U20 A17 A19 K17 D19 E19 D20 W16 DS3181/DS3182/DS3183/DS3184 NAME TSPA TEOP TSX TMOD[1] TMOD[0] TERR RSCLK RADR[4] RADR[3] RADR[2] RADR[1] RADR[0] RDATA[31] RDATA[30] RDATA[29] RDATA[28] RDATA[27] RDATA[26] RDATA[25] RDATA[24] RDATA[23] RDATA[22] RDATA[21] RDATA[20] RDATA[19] RDATA[18] RDATA[17] RDATA[16] RDATA[15] RDATA[14] RDATA[13] RDATA[12] RDATA[11] RDATA[10] RDATA[9] RDATA[8] RDATA[7] RDATA[6] RDATA[5] RDATA[4] RDATA[3] RDATA[2] RDATA[1] RDATA[0] RPRTY REN TYPE Oz I I FUNCTION Transmit Selected Packet Available Transmit End Of Packet Transmit Start of Transfer I Transmit Packet Data Modulus [1:0] I I Transmit Packet Error Receive System Clock I Receive Address [4:0] RDXA[1]/RPXA/RSX Oz RDXA[4] RDXA[3] RDXA[2] RSOX Oz Receive Data [31:0] (Tri-State) Oz I Receive Parity Receive Enable (Active Low) Receive Direct Cell/Packet Available [1]/Polled Cell/Packet Available/Start Of Transfer (TriState) O Receive Direct Cell/Packet Available [4:2] Oz Receive Start Of Cell/Packet (Tri-State) 44 PIN K16 V15 Y16 B18 B17 Y17 M20 T19 T20 R18 R19 R20 F16 G16 H16 J16 E17 F17 G17 H17 J17 H18 J18 E18 G19 H19 G20 H20 M16 N16 P16 R16 M17 N17 P17 P18 P19 P20 N18 N19 N20 M18 M19 L20 K20 G18 K19 E20 F18 F19 L17 DS3181/DS3182/DS3183/DS3184 NAME REOP RVAL RMOD[1] RMOD[0] RERR TYPE Oz Oz FUNCTION Receive End Of Packet Receive Packet Data Valid Oz Receive Packet Data Modulus [1:0] Oz Receive Packet Error PIN L16 K18 L19 L18 J19 MICROPROCESSOR INTERFACE D[15] D[14] D[13] D[12] D[11] D[10] D[9] D[8] D[7] D[6] D[5] D[4] D[3] D[2] D[1] D[0] A[10] A[9] A[8] A[7] A[6] A[5] A[4] A[3] A[2] A[1] A[0]/BSWAP ALE CS IO I I I RD/DS I WR/R/W RDY INT MODE WIDTH I Oz Oz I I Data [15:0] Address [10:1] Address [0] / Byte Swap Address Latch Enable Chip Select (Active Low) Read Strobe (Active Low) / Data Strobe (Active Low) Write Strobe (Active Low) / R/W Select Ready Handshake (Active Low) Interrupt (Active Low) Mode Select RD/WR or DS Strobe Mode WIDTH Select 8 or 16-Bit Interface 45 J5 T4 R4 P4 N4 V3 U3 T3 P3 N3 W2 U2 T2 P2 U1 P1 C3 D3 E3 G3 H3 D2 E2 G2 H2 E1 H1 N2 L3 K3 K4 K2 L4 B1 L5 DS3181/DS3182/DS3183/DS3184 NAME MISC I/O GPIO[8] GPIO[7] GPIO[6] GPIO[5] GPIO[4] GPIO[3] GPIO[2] GPIO[1] TEST HIZ RST TYPE IO I I I JTCLK JTMS JTDI JTDO JTRST I Ipu Ipu Oz Ipu CLKA CLKB CLKC I IO IO FUNCTION General-Purpose IO [8:1] Test Enable (Active Low) High-Impedance Test Enable (Active Low) Reset (Active Low) JTAG JTAG Clock JTAG Mode Select (with Pullup) JTAG Data Input (with Pullup) JTAG Data Output JTAG Reset (Active Low with Pullup) CLAD Clock A Clock B Clock C PIN V2 V1 C2 C1 P5 R5 G5 F5 M3 R3 B16 F3 F4 J3 G4 E4 K1 L1 L2 POWER VSS PWR Ground, 0V Potential VDD PWR Digital 3.3V 46 K10, K9, K8, J10, J9, J8, H10, H9, M7, M6, L7. L6, K7. K6, J7, J6, A1, N10, N9, M10, M9, M8, L10, L9, L8, R12, R11, R10, R9, P12, P11, P10, P9, Y1, N12, N11, M13, M12, M11, L13, L12, L11, M15, M14, L15, L14, K15, K14, J15, J14, Y20, K13, K12, K11, J13, J12, J11, H12, H11, G12, G11, G10, G9, F12, F11, F10, F9, A20 H8, H7, H6, G8, G7, G6, F8, F7, F6, A2, R8, R7, R6, P8, P7, P6, N8, N7, N6, W1, R15, R14, R13, P15, P14, P13, N15, N14, N13, Y19, H15, H14, H13, G15, G14, G13, F15, F14, F13, B20 DS3181/DS3182/DS3183/DS3184 NAME TYPE AVDDRn AVDDTn AVDDJn AVDDC PWR PWR PWR PWR NC NC FUNCTION Analog 3.3V for Receive LIU on Port n Analog 3.3V for Transmit LIU on Port n Analog 3.3V for Jitter Attenuator on Port n Analog 3.3V for CLAD NO CONNECTS No Connect, Unused 47 PIN # PORT 4 PORT 3 PORT 2 PORT 1 Y4 T7 V6 K5 A4 E7 C6 T1 N1 N5 D1 J4 G1 H4 H5 M4 M5 DS3181/DS3182/DS3183/DS3184 8.2 Detailed Pin Descriptions Table 8-2. Detailed Pin Descriptions n = 1,2,3,4 (port number). Ipu (input with pullup), Oz (output tri-stateable) (needs an external pullup or pulldown resistor to keep from floating), Oa (Analog output), Ia (analog input), IO (bidirectional in/out). All unused input pins without pullup should be tied low. PIN TYPE FUNCTION LINE IO TLCLKn O TPOSn / TDATn O Transmit Line Clock Output TLCLKn: This signal is available when the transmit line interface pins are enabled (PORT.CR2.TLEN). This clock is typically used as the clock reference for the TPOSn / TDATn and TNEG / TOHMOn signals, but can also be used as the reference for the TOHMIn / TSOFIn, TFOHn / TSERn, TFOHENIn and TSOFOn / TDENn / TFOHENOn signals. This output signal can be inverted. o DS3: 44.736 MHz +20 ppm o E3: 34.368 MHz +20 ppm o CC52: 52 MHz +20 ppm Transmit Positive AMI / Data Output TPOSn: When the port line interface is configured for B3ZS, HDB3 or AMI mode and the framer is not configured for one of the "-OHM" modes (see Table 10-32) and the transmit line interface pins are enabled (PORT.CR2.TLEN), a high on this pin indicates that a positive pulse should be transmitted on the line. The signal is updated on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is updated on the falling edge of the clock. The signal is typically referenced to the TLCLKn line clock output pins, but it can be referenced to the TCLKOn, TCLKIn, RLCLKn or RCLKOn pins. This output signal can be disabled when the TX LIU is enabled. This output signal can be inverted. TDATn: When the port line interface is configured for UNI mode or the framer is configured for one of the "-OHM" modes (see Table 10-32) and the transmit line interface pins are enabled (PORT.CR2.TLEN), the un-encoded transmit signal is output on this pin. The signal is updated on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is updated on the falling edge of the clock. The signal is typically referenced to the TLCLK line clock output pins, but it can be referenced to the TCLKOn, TCLKIn, RLCLKn or RCLKOn pins This output signal can be inverted. o DS3: 44.736 Mbps +20ppm o E3: 34.368 Mbps +20ppm o CC52: 52 Mbps +20ppm 48 DS3181/DS3182/DS3183/DS3184 PIN TYPE TNEGn / TOHMOn O TXPn Oa TXNn Oa RXPn Ia RXNn Ia FUNCTION Transmit Negative AMI / Line OH Mask TNEGn: When the port line is configured for B3ZS, HDB3 or AMI mode and the framer is not configured for one of the "-OHM" modes (see Table 10-32) and the transmit line interface pins are enabled (PORT.CR2.TLEN), a high on this pin indicates that a negative pulse should be transmitted on the line. The signal is updated on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is updated on the falling edge of the clock. The signal is typically referenced to the TLCLKn line clock output pins, but it can be referenced to the TCLKOn, TCLKIn, RLCLKn or RCLKOn pins. This output signal can be inverted. o DS3: 44.736 Mbps +20ppm o E3: 34.368 Mbps +20ppm o CC52: 52 Mbps +20ppm TOHMOn: When the framer is configured for one of the "-OHM" modes (see Table 10-32) and the transmit line interface pins are enabled (PORT.CR2.TLEN), the transmit overhead mask signal is output on this pin. This signal is a delayed version of TOHMIn or ROHMIn when in local loopback (three clock period delay). This signal will be high to indicate that the data on TDATn is not valid data and can be overwritten by external logic to add an external frame signal. This signal will be low to indicate that the data on TDATn is valid. The signal is updated on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is updated on the falling edge of the clock. The signal is typically referenced to the TLCLKn line clock output pins, but it can be referenced to the TCLKOn, TCLKIn, RLCLKn or RCLKOn pins. This output signal can be inverted. Transmit Positive Analog TXPn: This pin and the TXNn pin form a differential AMI output which is coupled to the outbound 75 coaxial cable through a 2:1 step-down transformer (Figure 1-1). This output is enabled when the TX LIU is enabled and the output is enabled to be driven. When it is not enabled, it is in a high impedance state. o DS3: 44.736 Mbps +20ppm o E3: 34.368 Mbps +20ppm o CC52: 52 Mbps +20ppm Transmit Negative Analog TXNn: This pin and the TXPn pin form a differential AMI output which is coupled to the outbound 75 coaxial cable through a 2:1 step-down transformer (Figure 1-1). This output is enabled when the TX LIU is enabled and the output is enabled to be driven. When it is not enabled, it is in a high impedance state. o DS3: 44.736 Mbps +20ppm o E3: 34.368 Mbps +20ppm o CC52: 52 Mbps +20ppm Receive Positive analog RXPn: This pin and the RXNn pin form a differential AMI input which is coupled to the outbound 75 coaxial cable through a 2:1 step-up transformer (Figure 1-1). This input is used when the RX LIU is enabled and is ignored when the LIU is disabled. o DS3: 44.736 Mbps +20ppm o E3: 34.368 Mbps +20ppm o CC52: 52 Mbps +20ppm Receive Negative analog RXNn: This pin and the RXPn pin form a differential AMI input which is coupled to the outbound 75 coaxial cable through a 2:1 step-up transformer (Figure 1-1). This input is used when the LIU is enabled and is ignored when the LIU is disabled. o DS3: 44.736 Mbps +20ppm o E3: 34.368 Mbps +20ppm o CC52: 52 Mbps +20ppm 49 DS3181/DS3182/DS3183/DS3184 PIN TYPE RLCLKn I RPOSn / RDATn I RNEGn / RLCVn / ROHMIn I FUNCTION Receive Line Clock Input RLCLKn: This clock is typically used for the reference clock for the RPOSn / RDATn, RNEGn / RLCVn / ROHMIn signals but can also be used as the reference clock for the RSERn, RSOFOn / RDENn / RFOHENOn, RFOHENIn, TOHMIn / TSOFIn, TFOHn / TSERn, TFOHENIn, TSOFOn / TDENn / TFOHENOn, TPOSn / TDATn and TNEGn / TOHMOn signals. This input is ignored when the LIU is enabled. This input signal can be inverted. o DS3: 44.736 MHz +20 ppm o E3: 34.368 MHz +20 ppm o CC52: 52 MHz +20 ppm Receive Positive AMI / Data RPOSn: When the port line is configured for B3ZS, HDB3 or AMI mode and the framer is not configured for one of the "-OHM" modes and the LIU is disabled, a high on this pin indicates that a positive pulse has been detected using an external LIU. The signal is sampled on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is sampled on the falling edge of the clock. The signal is typically referenced to the RLCLKn line clock input pins, but it can be referenced to the RCLKOn output pins. This input signal can be inverted. RDATn: When the port line interface is configured for UNI mode or the framer is configured for one of the "-OHM" modes, the un-encoded receive signal is input on this pin. The signal is sampled on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is sampled on the falling edge of the clock. The signal is typically referenced to the RLCLKn line clock input pins, but it can be referenced to the RCLKOn output pins. This input signal can be inverted. o DS3: 44.736 Mbps +20ppm o E3: 34.368 Mbps +20ppm o CC52: 52 Mbps +20ppm Receive Negative AMI / Line Code Violation / Line OH Mask input RNEGn: When the port line is configured for B3ZS, HDB3 or AMI mode and the framer is not configured for one of the "-OHM" modes and the LIU is disabled, a high on this pin indicates that a negative pulse has been detected using an external LIU. The signal is sampled on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is sampled on the falling edge of the clock. The signal is typically referenced to the RLCLKn line clock input pins, but it can be referenced to the RCLKOn output pins. This input signal can be inverted. o DS3: 44.736 Mbps +20ppm o E3: 34.368 Mbps +20ppm o CC52: 52 Mbps +20ppm RLCVn: When the port line interface is configured for UNI mode and the framer is not configured for one of the "-OHM" modes, the BPV counter in the encoder/decoder block is incremented each clock when this signal is high. The signal is sampled on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is sampled on the falling edge of the clock. The signal is typically referenced to the RLCLKn line clock input pins, but it can be referenced to the RCLKOn output pins. This input signal can be inverted. ROHMIn: When the port framer is configured for one of the "-OHM" modes, this signal is used to mark the overhead bits on the RDATn pins when it is high. The DS318x will ignore overhead bits. The signal is sampled on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is sampled on the falling edge of the clock. The signal is typically referenced to the RLCLKn line clock input pins, but it can be referenced to the RCLKOn output pins. This input signal can be inverted. 50 DS3181/DS3182/DS3183/DS3184 PIN TYPE FUNCTION DS3/E3 OVERHEAD INTERFACE TOHn I TOHENn I TOHCLKn O TOHSOFn O ROHn O ROHCLKn O Transmit Overhead / Line OH Mask Input TOHn: When the port framer is configured for one of the DS3 or E3 framing modes, this signal will be used to over-write the DS3 or E3 framing overhead bits when TOHENn is active. In T3 mode, the X-bits, P-bits, M-bits, F-bits, and C-bits are input. In G.751 E3 mode, all of the FAS, RAI, and National Use bits are input. In G.832 E3 mode, all of the FA1, FA2, EM, TR, MA, NR, and GC bytes are input. The TOHSOFn signal marks the start of the framing bit sequence. This signal is sampled at the same time as the TOHCLKn signal transitions high to low. This signal can be inverted. Transmit Overhead Enable / Start Of Frame Input TOHENn: When the port framer is configured for one of the DS3 or E3 framing modes, this signal will be used the determine which DS3 or E3 framing overhead bits to over-write with the signal on the TOHn pins. The TOHSOFn signal marks the start of the framing bit sequence. This signal is sampled at the same time as the TOHCLKn signal transitions high to low. This signal can be inverted. Transmit Overhead Clock TOHCLKn: When the port framer is configured for one of the DS3 or E3 framing modes, this clock is used for the transmit overhead port signals TOHn, TOHENn and TOHSOFn. The TOHSOFn output signal is updated and the TOHn and TOHENn input signals are sampled at the same time this clock signal transitions from high to low. The external logic is expected to sample TOHSOFn signal and update the TOHn and TOHENn signals on the rising edge of this clock signal. This clock is a low frequency clock. This signal can be inverted. Transmit Overhead Start Of Frame TOHSOFn: When the port framer is configured for one of the DS3 or E3 framing modes, this signal is used to mark the start of a DS3 or E3 overhead sequence on the TOHn pins. In T3 mode, the first X-bit is marked. In G.751 E3 mode, the first bit of the FAS word is marked. In G.832 E3 mode, the first bit of the FA1 byte is marked. The sequence starts on the same high to low transition of the TOHCLKn clock that this signal is high. This signal is updated at the same time as the TOHCLKn signal transitions high to low. This signal can be inverted. Receive Overhead ROHn: When the port framer is configured for one of the DS3 or E3 framing modes, this signal outputs the value of the receive overhead bits. The ROHSOFn signal marks the start of the framing bit sequence. In T3 mode, the X-bits, P-bits, M-bits, Fbits, and C-bits are output (Note: In M23 mode, the C-bits are extracted even though they are marked as data at the payload interface). In G.751 E3 mode, all of the FAS, RAI, and National Use bits are output. In G.832 E3 mode, all of the FA1, FA2, EM, TR, MA, NR, and GC bytes are output. This signal is updated at the same time as the ROHCLKn signal transitions high to low. This signal can be inverted. Receive Overhead Clock ROHCLKn: When the port framer is configured for one of the DS3 or E3 framing modes, this clock is used for the receive overhead port signals ROHn and ROHSOFn. The ROHSOFn and ROHn output signals are updated at the same time this clock signal transitions from high to low. The external logic is expected to sample ROHSOFn and ROHn signal on the rising edge of this clock signal. This clock is a low frequency clock. This signal can be inverted. 51 DS3181/DS3182/DS3183/DS3184 PIN ROHSOFn TYPE FUNCTION O Receive Overhead Start Of Frame ROHSOFn: When the port framer is configured for one of the DS3 or E3 framing modes this signal is used to mark the start of a DS3 or E3 overhead sequence on the ROHn pins. In T3 mode, the first X-bit is marked. In G.751 E3 mode, the first bit of the FAS word is marked. In G.832 E3 mode, the first bit of the FA1 byte is marked. The sequence starts on the same high to low transition of the ROHCLKn clock that this signal is high. This signal is updated at the same time as the ROHCLKn signal transitions high to low. This signal can be inverted. DS3/E3 SERIAL DATA, PLCP AND FRACTIONAL DS3/E3 OVERHEAD INTERFACE TCLKIn I TSOFIn / TOHMIn I TSERn / TPOHn / TFOHn / I Transmit Line Clock Input TCLKIn: This clock is typically used for the reference clock for the TOHMIn / TSOFIn, TFOHn / TSERn, TFOHENIn / TPDENIn, TPDATn, TPDENOn and TSOFOn / TDENn / TFOHENOn signals but can also be used as the reference for the TPOSn / TDATn and TNEGn / TOHMOn signals. This clock is not used when the part is in loop time mode or the CLAD clocks are used as the transmit clock source. (PORT.CR3.CLADC) This input signal can be inverted. o DS3: 44.736 MHz +20 ppm o E3: 34.368 MHz +20 ppm o CC52: 52 MHz +20 ppm Transmit Start Of Frame Input / OH Mask Input. See Table 10-20. TSOFIn: When the port framer is configured for any of the DS3 or E3 non "-OHM" framed modes, this signal can be used to align the start of the DS3 or E3 frames on the TSER pin to an external signal. In the fractional mode, the TSOFIn signal can be used to align the start of frame signal position on the TSERn/TOHn pin to the rising edge of a signal on this pin. The signal edge does not need to occur on every frame and can be tied high or low. The signal is sampled on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is sampled on the falling edge of the clock. The signal is typically referenced to the TCLKIn transmit clock input pins, but it can be referenced to the TLCLKn, TCLKOn, RCLKOn and RLCLKn clock pins. This signal can be inverted. TOHMIn: When the port framer is configured for one of the "- OHM" modes, this signal is used to mark clock periods when valid data bits are available on the TDATn output pins. When this signal is low, valid data bits will be available on the TDATn output pins three clock periods later. This signal precedes the signal on TDATn and TOHMOn by three clock periods. The signal is sampled on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is sampled on the falling edge of the clock. The signal is typically referenced to the TCLKIn transmit clock input pins, but it can be referenced to the TLCLKn, TCLKOn, RCLKOn and RLCLKn clock pins. This signal can be inverted. Transmit Serial Data / PLCP Overhead / Fractional Overhead. See Table 10-21. TSERn: When the port framer is configured for Flexible Fractional mode, this pin is used as the source of the DS3/E3 payload data. The signal is sampled on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is sampled on the falling edge of the clock. The signal is typically referenced to the TCLKIn transmit clock input pins, but it can be referenced to the TLCLKn, TCLKOn / TGCLKn, RCLKOn and RLCLKn clock pins This signal can be inverted. o DS3: 44.736 Mbps +20ppm o E3: 34.368 Mbps +20ppm o CC52: 52 Mbps +20ppm TPOHn: When the port framer is configured for one of the DS3 or E3 PLCP framing modes, and the port is enabled, this signal will be used to over-write the DS3 or E3 52 DS3181/DS3182/DS3183/DS3184 PIN TYPE TPDENIn / TPOHENn / TFOHENIn I TCLKOn / TGCLKn / TPOHCLKn O FUNCTION PLCP framing overhead bits when TPOHENn is active. The TPOHSOFn signal marks the start of the framing bit sequence. This signal is sampled at the same time as the TPOHCLKn signal transitions high to low. This signal can be inverted. TFOHn: When the port framer is configured for one of the DS3 or E3 internal or external fractional framing modes, and the port is enabled the internal fractional framing modes, this pin can be used to source the fractional overhead data. The signal is sampled on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is sampled on the falling edge of the clock. The signal is typically referenced to the TCLKIn transmit clock input pins, but it can be referenced to the TLCLKn, TCLKOn / TGCLKn, RCLKOn and RLCLKn clock pins This signal can be inverted. Transmit Payload Data Enable Input / PLCP Overhead Enable / Fractional OH Enable Input. See Table 10-22. TPDENIn: When the port is configured for the Flexible fractional mode, this pin is used to enable payload data from the cell/packet processor. There is a three-clock delay between TPDENIn and TPDENOn. The signal is sampled on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is sampled on the falling edge of the clock. The signal is typically referenced to the TCLKIn transmit clock input pins, but it can be referenced to the TLCLKn, TCLKOn, RCLKOn and RLCLKn clock pins This signal can be inverted. TPOHENn: When the port framer is configured for one of the DS3 or E3 PLCP framing modes, and the port is enabled, this signal will be used the determine which DS3 or E3 PLCP framing overhead bits to over-write with the signal on the TPOHn pins. The TPOHSOFn signal marks the start of the framing bit sequence. This signal is sampled at the same time as the TPOHCLKn signal transitions high to low. This signal can be inverted. TFOHENIn: When the port framer is configured for the DS3 or E3 External Fractional framing, this pin is used to mark the fractional overhead data on the TFOHn pin. The TSOFOn or TSOFIn pins can be used to select which DS3/E3 payload bits relative to the start of the DS3/E3 frame to mark. The signal is sampled on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is sampled on the falling edge of the clock. The signal is typically referenced to the TCLKIn transmit clock input pins, but it can be referenced to the TLCLKn, TCLKOn, RCLKOn and RLCLKn clock pins This signal can be inverted. Transmit Clock Output / Gapped Clock / PLCP Overhead Clock. See Table 10-24. TCLKOn: When the port is configured external fractional modes and TCLKOn is selected, or any other mode and the port pins are enabled and TCLKOn is selected, this clock output is enabled. This clock is the same clock as the internal framer transmit clock. This clock is typically used for the reference clock for the TOHMIn / TSOFIn, TFOHn / TSERn, TFOHENIn and TSOFOn / TDENn / TFOHENOn signals but can also be used as the reference for the TPOSn / TDATn and TNEGn / TOHMOn signals. This signal can be inverted. o DS3: 44.736 MHz +20 ppm o E3: 34.368 MHz +20 ppm o CC52: 52 MHz +20 ppm TGCLKn: When the port is configured internal fractional mode or any simple DS3/E3 framed mode and the port pins are enabled and TGCLKn is selected, this gated output clock is enabled. This gapped clock is the same clock as the internal framer transmit clock and is gated by either TDENn or TFOHENOn depending on which signal is active. This clock is typically used for the reference clock for the TFOHn / TSERn signals. This signal can be inverted. TPOHCLKn: When the port framer is configured for one of the DS3 or E3 PLCP 53 DS3181/DS3182/DS3183/DS3184 PIN TSOFOn / TDENn / TPOHSOFn / TFOHENOn TYPE O FUNCTION framing modes, the port pins are enabled and the TCLKOn pin function is not selected, this clock is used for the transmit overhead port signals TPOHn, TPOHENn and TPOHSOFn. The TPOHSOFn output signal is updated and the TPOHn and TPOHENn input signals are sampled at the same time this clock signal transitions from high to low. The external logic is expected to sample TPOHSOFn signal and update the TPOHn and TPOHENn signals on the rising edge of this clock signal. This clock is a low frequency clock. This signal can be inverted. Transmit PLCP Overhead Start Of Frame / Framer Start Of Frame /Data Enable See Table 10-23. TSOFOn: When the port framer is configured for the External Fractional or Flexible Fractional modes and the port pins are enabled and the TSOFOn pin function is selected, this signal is used to indicate the start of the DS3/E3 frame on the TPOHn / TFOHn / TSERn pin. The signal is also active in the non-PLCP non-fractional DS3 or E3 framing modes when the port pins are enabled and the TSOFOn pin function is selected. This signal pulses high three clocks before the first overhead bit in a DS3 or E3 frame that will be input on TSERn or TFOHn. The signal is updated on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is updated on the falling edge of the clock. The signal is typically referenced to the TCLKIn transmit clock input pins, but it can be referenced to the TLCLKn, TCLKOn, RCLKOn and RLCLKn clock pins. This signal can be inverted. TDENn: When the port framer is configured for the External Fractional or Flexible Fractional modes and the port pins are enabled and the TDENn pin function is selected, this signal is used to mark the DS3/E3 frame bits on the TPOHn / TFOHn / TSERn pin. The signal is also active in the non-PLCP non-fractional DS3 or E3 framing modes when the port pins are enabled and the TDENn pin function is selected. The signal goes high three clocks before the start of DS3/E3 payload bits and goes low three clocks before the end of the DS3/E3 payload bits. The signal is updated on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is updated on the falling edge of the clock. The signal is typically referenced to the TCLKIn transmit clock input pins, but it can be referenced to the TLCLKn, TCLKOn, RCLKOn and RLCLKn clock pins. This signal can be inverted. TPOHSOFn: When the port framer is configured for one of the PLCP framing modes and the port pins are enabled, this signal is used to mark the start of a DS3 or E3 PLCP overhead sequence on the TPOHn pins. The sequence starts on the same high to low transition of the TPOHCLKn clock that this signal is high. This signal is updated at the same time as the TPOHCLKn signal transitions high to low. This signal can be inverted. TFOHENOn: When the port framer is configured for one of the internal fractional modes and the port pins are enabled, this signal is used to indicate the fractional overhead bit positions of the data on the TOHn pin. The signal goes high one clock before the start of DS3/E3 fractional overhead bits and goes low one clock before the end of the DS3/E3 fractional payload bits. The signal is updated on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is updated on the falling edge of the clock. The signal is typically referenced to the TCLKIn transmit clock input pin, but it can be referenced to the TLCLKn, TCLKOn, RCLKOn or RLCLKn clock pin. This signal can be inverted. 54 DS3181/DS3182/DS3183/DS3184 PIN TYPE TPDENOn O TPDATn O RPDENIn / RFOHENIn I RPDATn I RSERn / RPOHn O FUNCTION Transmit Payload Data Enable Output. See Table 10-26. TPDENOn: When the port framer is enabled for the Flexible fractional mode and the port pins are enabled, this signal marks which bits on the TPDATn pin are valid payload data bits. It is high during the same clock cycle the TPDATn payload data bit is valid. The signal is updated on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is updated on the falling edge of the clock. The signal is typically referenced to the TCLKIn transmit clock input pin, but it can be referenced to the TLCLKn, TCLKOn, RCLKOn or RLCLKn clock pin. This signal can be inverted. Transmit Payload Data. See Table 10-26. TPDATn: When the port framer is enabled for the Flexible fractional mode and the port pins are enabled, this signal is the payload bits from the cell/packet processor. The data is valid if the TPDENOn signal is high during the same clock cycle. The signal is updated on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is updated on the falling edge of the clock. The signal is typically referenced to the TCLKIn transmit clock input pin, but it can be referenced to the TLCLKn, TCLKOn, RCLKOn or RLCLKn clock pin. This signal can be inverted. Receive Payload Data Enable Input / Fractional Overhead Enable Input See Table 10-28. RPDENIn: When the port is configured for the flexible fractional mode, this pin is used to enable payload data for the cell/packet processor. The data on RPDATn is used when this signal is high. The signal is sampled on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is sampled on the falling edge of the clock. The signal is typically referenced to the RCLKOn receive clock output pins, but it can be referenced to the RLCLKn clock input pin. This signal can be inverted. RFOHENIn: When the port framer is configured for the external fractional framing mode, this pin is used to mark the receive bits to use for fractional overhead data. The signal on the RSOFOn pin can be used to select which DS3/E3 payload bits relative to the start of the DS3/E3 frame to mark. The signal needs to go high for each bit on the RSERn pin that should be treated as fractional overhead in the DS3/E3 payload. RFOHENIn needs to go high or low three clock periods after the data bit on RSERn is present to mark that bit as payload or fractional overhead. The signal is sampled on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is sampled on the falling edge of the clock. The signal is typically referenced to the RCLKOn receive clock output pins, but it can be referenced to the RLCLKn clock input pin. This signal can be inverted. Receive Payload Data. See Table 10-29. RPDATn: When the port framer is enabled for the Flexible fractional mode and the port pins are enabled, this signal is the payload bits for the cell/packet processor. The data is used if the RPDENOn signal is high during the same clock cycle. The signal is sampled on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is sampled on the falling edge of the clock. The signal is typically referenced to the RCLKOn receive clock output pins, but it can be referenced to the RLCLKn clock input pin. This signal can be inverted. Receive Serial Data / PLCP Overhead. See Table 10-27. RSERn: When the port framer is configured for the external fractional mode, internal fractional mode, or flexible fractional mode, and the port pins are enabled, this pin outputs the receive data signal from the LIU or receive line pins. The signal is updated on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is updated on the falling edge of the clock. The signal is typically referenced to the RCLKOn receive clock output pin, but it can be referenced to the RGCLKn and RLCLKn clock pins. This signal can be inverted 55 DS3181/DS3182/DS3183/DS3184 PIN RCLKOn / RGCLKn / RPOHCLKn TYPE O FUNCTION o DS3: 44.736 Mbps +20ppm o E3: 34.368 Mbps +20ppm o CC52: 52 Mbps +20ppm RPOHn: When the port framer is configured for one of the PLCP framing modes and the port pins are enabled, this signal outputs the value of the receive PLCP overhead bits. The RPOHSOFn signal marks the start of the framing bit sequence. This signal is updated at the same time as the RPOHCLKn signal transitions high to low. This signal can be inverted. Receive Clock Output / Gapped Clock / PLCP Overhead Clock. See Table 10-31. RCLKOn: When the port is configured for external fractional mode or flexible fractional mode and RCLKOn is selected, or any other mode and the port pins are enabled and RCLKOn is selected, this clock output signal is active. It is the same as the internal receive framer clock. This clock is typically used for the reference clock for the RSERn, RSOFOn / RDENn / RFOHENOn, RPDATn, and RFOHENIn / RPDENIn signals but can also be used as the reference for the RPOSn / RDATn, RNEGn / RLCVn / ROHMIn TOHMIn / TSOFIn, TFOHn / TSERn, TFOHENIn, TSOFOn / TDENn / TFOHENOn, TPOSn / TDATn and TNEGn / TOHMOn signals. This signal can be inverted. o DS3: 44.736 MHz +20 ppm o E3: 34.368 MHz +20 ppm o CC52: 52 MHz +20 ppm RGCLKn: When the port is configured for internal fractional or any simple DS3/E3 framed mode and the port pins are enabled and RGCLKn is selected, this gated clock output signal is active. It is the internal receive framer clock gated by either RDENn or RFOHENOn, depending on which signal is active. This clock is typically used as the reference clock for the RSERn pin. This signal can be inverted RPOHCLKn: When the port framer is configured for one of the PLCP framing modes and the port pins are enabled, this clock is used for the receive PLCP overhead port signals RPOHn and RPOHSOFn. The RPOHSOFn and RPOHn output signals are updated at the same time this clock signal transitions from high to low. The external logic is expected to sample RPOHSOFn and RPOHn signal on the rising edge of this clock signal. This clock is a low frequency clock. This signal can be inverted. 56 DS3181/DS3182/DS3183/DS3184 PIN TYPE RSOFOn / RDENn / RPOHSOFn / RFOHENOn O TSCLK I TADR[4:0] I TDATA[31:0] I FUNCTION Receive Framer Start Of Frame /Data Enable / PLCP Overhead Start Of Frame. See Table 10-30. RSOFOn: When the port framer is configured for External Fractional or Flexible Fractional mode and the RSOFOn pin function is enabled, or when it is configured for one of the DS3 or E3 framed only modes and the port pins are enabled and the RSOFOn pin function is enabled, this signal is used to indicate the start of the DS3/E3 frame. This signal indicates the first DS3/E3 overhead bit on the RSERn pin when high. The signal is updated on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is updated on the falling edge of the clock. The signal is typically referenced to the RCLKOn receive clock output pin, but it can be referenced to the RLCLKn clock input pin. This signal can be inverted. RDENn: When the port framer is configured for External Fractional or Flexible Fractional mode and the RDENn pin function is enabled and the port pins are enabled and the RDENn pin function is enabled, this signal is used to indicate the DS3/E3 payload bit positions of the data on the RSERn pin. The signal goes high during each DS3/E3 payload bit and goes low during each DS3/E3 overhead bit. The signal is updated on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is updated on the falling edge of the clock. The signal is typically referenced to the RCLKOn receive clock output pin, but it can be referenced to the RLCLKn clock input pin. This signal can be inverted. RPOHSOFn: When the port framer is configured for one of the PLCP framing modes and the port pins are enabled, this signal is used to mark the start of a DS3 or E3 PLCP overhead sequence on the RPOHn pins. The sequence starts on the same high to low transition of the RPOHCLKn clock that this signal is high. This signal is updated at the same time as the RPOHCLKn signal transitions high to low. This signal can be inverted. RFOHENOn: When the port framer is configured for internal fractional mode and the port pins are enabled, this signal is used to indicate the fractional overhead bit positions of the data on the RSERn pin. The signal goes high during each DS3/E3 fractional overhead bit and goes low during each DS3/E3 fractional payload bit. The signal is updated on the positive clock edge of the referenced clock pin if the clock pin signal is not inverted, otherwise it is updated on the falling edge of the clock. The signal is typically referenced to the RCLKOn receive clock output pin, but it can be referenced to the RLCLKn clock input pin. This signal can be inverted. UTOPIA/POS-PHY/SPI-3 SYSTEM INTERFACE Transmit System Clock TSCLK: This signal is used to sample or update the other transmit system interface signals. TSCLK has a maximum frequency of 66 MHz in L3 modes and 52 MHz in L2 modes. Transmit Address [4:0] TADR[4:0]: In UTOPIA L2, UTOPIA L3 or POS-PHY L2 modes, this 5-bit address bus is used by the ATM/Link layer device to select a specific port for data transfer or to poll for FIFO status.. In POS-PHY L3 modes, this 5-bit address is used by the Link layer device to poll for FIFO status. TADR[4] is the MSB and TADR[0] is the LSB. This bus is sampled on the rising edge of TSCLK. Transmit Data [31:0] TDATA[31:0]: This 32-bit data bus is used to transfer cell/packet data from the ATM/Link layer device. This bus is sampled on the rising edge of TSCLK. In 32-bit mode, TDATA[31] is the MSB and TDATA[0] is the LSB. In 16-bit mode, TDATA[15] is the MSB, TDATA[0] is the LSB, and TDATA[31:16] are not used and ignored. 57 DS3181/DS3182/DS3183/DS3184 PIN TYPE TPRTY I TEN I TDXA[1] / TPXA Oz TDXA[4:2] O TSOX I TSPA Oz FUNCTION In 8-bit mode, TDATA[7] is the MSB, TDATA[0] is the LSB, and TDATA[31:8] are not used and ignored. Transmit Parity TPRTY: This signal indicates the parity on the data bus when parity checking is enabled. This option is programmable. TPRTY is ignored if parity checking is disabled. This signal is sampled on the rising edge of TSCLK. Transmit Enable (active low) TEN: This signal is used by the ATM/Link device to control the transfer of cell/packet data on the TDATA bus. If TEN is high, no transfer occurs. If TEN is low, a transfer occurs. This signal can be sampled on the rising edge of TSCLK. Transmit Direct Cell/Packet Available [1] / Polled Cell/Packet Available (tri-state) This signal is tri-state when global reset is applied. TDXA[1]: When direct status mode is selected, this signal is used to indicate when port 1 can accept data from the ATM/Link layer device. This signal is updated on the rising edge of TSCLK. In UTOPIA L2 or UTOPIA L3 modes, TDXA goes high when port 1 can accept the transfer of more than a programmable number of ATM cells. TDXA goes low when port 1 cannot accept the transfer of a complete ATM cell. In POS-PHY L2 or POS-PHY L3 modes, TDXA goes high when port 1 can store more data than the "almost full" level. TDXA goes low when port 1 is full. TPXA: (reset default) When polled status mode is selected, this signal is used to indicate when the polled port, as selected by TADR[4:0], can accept data from the ATM/Link layer device. This signal is updated on the rising edge of TSCLK. In UTOPIA L2 or UTOPIA L3 modes, TPXA goes high when the polled port's FIFO can accept the transfer of more than a programmable number of ATM cells (the "almost full" level). TPXA goes low when the polled port cannot accept the transfer of a complete ATM cell. In POS-PHY L2 or POS-PHY L3 modes, TPXA goes high when the polled port's FIFO can store more data than the "almost full" level. TPXA goes low when the polled port is full. In UTOPIA L2 (reset default) or POS-PHY L2 modes, this signal is driven when one of the ports is being polled, and is tri-stated when none of the ports is being polled or when data path reset is active. In UTOPIA L3 or POS-PHY L3 modes, this signal is driven. Note: Polled status mode or direct status mode is selected by the GL.CR1.DIREN bit. Transmit Direct Cell/Packet Available [4:2] TDXA[4:2]: This signal is used to indicate when the associated port can accept data from the ATM/Link layer device. This signal can be updated on the rising edge of TSCLK. In UTOPIA L2 or L3 modes, TDXA goes high when the associated port's can accept the transfer of more than a programmable number of ATM cells ("almost full" level). TDXA goes low when the associated port cannot accept the transfer of a complete ATM cell. In POS-PHY L2 or L3 modes, TDXA goes high when the associated port's FIFO can store more data than the "almost full" level. TDXA goes low when the associated port's FIFO is full. Transmit Start Of Cell/Packet TSOX: This signal is used to indicate the first transfer of a cell/packet. This signal can be sampled on the rising edge of TSCLK. In UTOPIA L2 or L3 modes, TSOX indicates the first transfer of a cell. In POS-PHY L2 or L3 modes, TSOX indicates the first transfer of a packet. Transmit Selected Packet Available This signal is tri-state when global reset is applied. TSPA: In POS-PHY L2 or POS-PHY L3 modes, this signal is used to indicate the selected port can accept data from the Link layer device. TSPA goes high when a port is selected for transfer and it can accept more data than the "almost full" level. 58 DS3181/DS3182/DS3183/DS3184 PIN TYPE TEOP I TSX I TMOD[1:0] I TERR I RSCLK I RADR[4:0] I FUNCTION TSPA goes low when the selected port is "full" or no port is selected. This signal is updated on the rising edge of TSCLK. In UTOPIA L3 mode this signal is low. In POS-PHY L2 mode, this signal is driven when one of the ports is selected for data transfer, and tri-state when TEN is deasserted, none of the ports is selected or when data path reset is active. POS-PHY L3 or UTOPIA L3 modes this signal is driven. In UTOPIA L2 (reset default) mode this signal is tri-stated. Transmit End Of Packet TEOP: In POS-PHY L2 or L3 modes, this signal is used to indicate the last transfer of a packet. This signal is sampled on the rising edge of TSCLK. In UTOPIA L2 or L3 modes, this signal is ignored. Transmit Start Of Transfer TSX: In POS-PHY L3 mode, this signal indicates the start of a data transfer. TSX goes high goes high immediately before the start of data transfer to indicate that the in-band port address is present on TDATA. TSX goes high when the value of TDATA is the address of the transmit port to which data is to be transferred. When TSX goes low, all subsequent transfers will be to the port specified by the in-band address. This signal is sampled on the rising edge of TSCLK. TSX is only valid when TEN is high. In UTOPIA L2, UTOPIA L3 or POS-PHY L2 modes, this signal is ignored. Transmit Packet Data Modulus [1:0] TMOD[1:0]: In POS-PHY L2 or L3 modes, this signal indicates the number of valid bytes on the TDATA bus. TMOD[1:0]=00 TDAT[31:0] valid TMOD[1:0]=01 TDAT[31:8] valid TMOD[1:0]=10 TDAT[31:16] valid TMOD[1:0]=11 TDAT[31:24] valid This signal is sampled on the rising edge of TSCLK. TMOD is only valid when TEOP is high. In 16-bit POS-PHY L2 or 16-bit POS-PHY L3 mode, TMOD[1] is ignored. In 8-bit POS-PHY L2 or 8-bit POS-PHY L3 modes, TMOD[1:0] are ignored. In UTOPIA L2 or UTOPIA L3 modes, TMOD[1:0] are ignored. Transmit Packet Error TERR: In POS-PHY L2 or POS-PHY L3 modes, this signal indicates that the current packet is erred. When TERR is high, the current packet should be aborted. This signal is sampled on the rising edge of TSCLK. TERR is only valid when TEOP is high. In UTOPIA L2 or UTOPIA L3 modes, this signal is ignored. Receive System Clock RSCLK: This signal is used to sample or update the other receive system interface signals. RSCLK has a maximum frequency of 66 MHz in UTOPIA L3 or POS-PHY L3 modes and 52 MHZ in UTOPIA L2 or POS-PHY L2 modes. Receive Address [4:0] RADR[4:0]: In UTOPIA L2, Utopia L3 or POS-PHY L2 modes, this 5-bit address bus is used by the ATM/Link layer device to select a specific port for data transfer and polling FIFO status. RADR[4] is the MSB and RADR[0] is the LSB. This bus is sampled on the rising edge of RSCLK. In POS-PHY Level 3 (or SPI-3) mode, this bus is ignored. 59 DS3181/DS3182/DS3183/DS3184 PIN TYPE RDATA[31:0] Oz RPRTY Oz REN I RDXA[1] / RPXA / RSX Oz FUNCTION Receive Data [31:0] (tri-state) This signal is tri-state when global reset is applied. RDATA[31:0]: This 32-bit data bus is used to transfer cell/packet data to the ATM/Link layer device. This bus is updated on the rising edge of RSCLK. In 32-bit modeRDATA[31] is the MSB and RDATA[0] is the LSB. In UTOPIA L2 or POS-PHY L2 modes, RDATA[31:0] are driven when one of the ports is selected for data transfer, and tri-stated when REN is deasserted, none of the ports is selected or data path reset is active. In UTOPIA L3 or POS-PHY L3 modes RDATA[31:0] are driven. In 16-bit modeRDATA[15] is the MSB, RDATA[0] is the LSB, and RDATA[31:16] are not used. In UTOPIA L2 or POS-PHY L2 modes, RDATA[15:0] are driven when one of the ports is selected for data transfer, and tri-stated when REN is deasserted, none of the ports is selected or data path reset is active. RDATA[31:16] are tri-stated. In UTOPIA L3 or POS-PHY L3 modes, RDATA[31:0] are driven. In 8-bit mode (reset default)RDATA[7] is the MSB, RDATA[0] is the LSB, and RDATA[31:8] are not used. In UTOPIA L2 (reset default) or POS-PHY L2 modes, RDATA[7:0] are driven when one of the ports is selected for data transfer, and tri-stated when REN is deasserted, none of the ports is selected or data path reset is applied. RDATA[31:8] are tri-stated. In UTOPIA L3 or POS-PHY L3 modes, RDATA[31:0] are driven. Receive Parity (tri-state) RPRTY: This signal indicates the parity on the data bus when parity generation is enabled. This option programmable. RPRTY is held low if parity generation is disabled. This signal is updated on the rising edge of RSCLK. In UTOPIA L2 (reset default) or POS-PHY L2 modes, this signal is driven when one of the ports is selected for data transfer, and tri-stated when REN is deasserted, none of the ports is selected or data path reset is active. In UTOPIA L3 or POS-PHY L3 modes this signal is driven. Receive Enable (active low) REN: This signal is used by the ATM/Link device to control the transfer of cell/packet data on the RDATA bus. If REN is high, no transfer occurs. If REN is low, a transfer occurs. This signal can be sampled on the rising edge of RSCLK. Receive Direct Cell/Packet Available [1] / Polled Cell/Packet Available / Start of Transfer (tri-state) This signal is tri-state when global reset is applied. RDXA[1]: This signal is active in UTOPIA L2, Utopia L3 or POS-PHY L2 modes when direct status mode is selected. It is used to indicate when port 1 can send data to the ATM/Link layer device. This signal is updated on the rising edge of RSCLK. In UTOPIA L2 or UTOPIA L3 modes, RDXA goes high when the port 1 FIFO has more than a programmable number of ATM cells ready for transfer ("almost empty" level). RDXA goes low when the associated port does not have a complete ATM cell ready for transfer. In POS-PHY L2 mode, RDXA goes high when the port 1 FIFO contains more data than the "almost empty" level or has an end of packet ready for transfer. RDXA goes low when the associated port does not have an end of packet ready for transfer and is "almost empty". RPXA: (Reset default) This signal is active in UTOPIA L2, UTOPIA L3 or POS-PHY L2 modes when polled status mode is selected. It is used to indicate when the polled port, as selected by RADR[4:0], can send data to the ATM/Link layer device. This signal is updated on the rising edge of RSCLK. 60 DS3181/DS3182/DS3183/DS3184 PIN TYPE RDXA[4:2] O RSOX Oz REOP Oz FUNCTION In UTOPIA L2 or UTOPIA L3 modes, RPXA goes high when the polled port has more than a programmable number of ATM cells ready for transfer ("almost empty" level of the associated FIFO). RPXA goes low when the polled port's FIFO does not have a complete ATM cell ready for transfer. In POS-PHY L2 mode, RPXA goes high when the polled port's FIFO contains more data than the "almost empty" level or has an end of packet ready for transfer. RPXA goes low when the port does not have an end of packet ready for transfer and is "almost empty". In UTOPIA L2 (reset default) or POS-PHY L2 modes, this signal is driven when one of the ports is being polled, and is tri-stated when none of the ports is being polled or when data path reset is active. In UTOPIA L3 mode this signal is driven. RSX: This signal is active in POS-PHY L3 modes and indicates the start of a data transfer. This signal is updated on the rising edge of RSCLK. RSX goes high immediately before the start of data transfer to indicate that the inband port address is present on RDATA. RSX goes high when the value of RDATA is the address of the receive port from which data is to be transferred. When RSX goes low, all subsequent transfers will be from the port specified by the in-band address. When RSX is high, RVAL must be low. This signal is always driven in POS-PHY L3 mode. Receive Direct Cell/Packet Available [4:2] RDXA[4:2]: This signal is used to indicate when the associated port can send data to the ATM/Link layer device. This signal is updated on the rising edge of RSCLK. In UTOPIA L2 or UTOPIA L3 modes, RDXA goes high when the associated port has more than a programmable number of ATM cells ready for transfer ("almost empty" level). RDXA goes low when the associated port does not have a complete ATM cell ready for transfer. In POS-PHY L2 mode, RDXA goes high when the associated port's FIFO contains more data than the "almost empty" level or has an end of packet ready for transfer. RDXA goes low when the associated port's FIFO does not have an end of packet ready for transfer and is "almost empty". In POS-PHY Level 3 (or SPI-3) mode or when polled status mode is selected, these signals are held low. Receive Start Of Cell/Packet (tri-state) This signal is tri-state when global reset is applied. RSOX: This signal is used to indicate the first transfer of a cell/packet. This signal is updated on the rising edge of RSCLK. In UTOPIA L2 or UTOPIA L3 modes, RSOX is used to indicate the first transfer of a cell. In POS-PHY L2 or POS-PHY L3 modes, RSOX is used to indicate the first transfer of a packet. In UTOPIA L2 (reset default) or POS-PHY L2 modes, this signal is driven when one of the ports is selected for data transfer, and tri-stated when REN is deasserted, none of the ports is selected or data path reset is active. In UTOPIA L3 or POS-PHY L3 modes this signal is driven. Receive End Of Packet (tri-state) This signal is tri-state when global reset is applied. REOP: In POS-PHY L2 or POS-PHY L3 modes, this signal is used to indicate the last transfer of a packet. This signal is updated on the rising edge of RSCLK. In UTOPIA L3 mode, this signal is held low. In POS-PHY L2 mode, this signal is driven when one of the ports is selected for data transfer, and tri-stated when REN is deasserted, none of the ports is selected or data path reset is active. In UTOPIA L2 (reset default) mode this signal is tri-stated. In all UTOPIA L3 or POS-PHY L3 modes this signal is driven. 61 DS3181/DS3182/DS3183/DS3184 PIN RVAL RMOD[1:0] RERR TYPE FUNCTION Oz Receive Packet Data Valid (tri-state) This signal is tri-state when global reset is applied. RVAL: In POS-PHY L2 or POS-PHY L3 modes, this signal is used to indicate the validity of a receive data transfer. When RVAL is high, the receive data bus (RDATA, RPRTY, RSOX, REOP, RMOD, and RERR) is valid and a packet data transfer occurs. When RVAL is low, the receive data bus is invalid and a data transfer does not occurs. This signal is updated on the rising edge of RSCLK. RVAL goes high when a port is selected for packet data transfer and the port has a programmable size block of data or an end of packet ready for transfer. In POS-PHY L2 mode, RVAL goes low if the selected port is empty, at the end of a packet, or when REN is deasserted. Once RVAL goes low, it will remain low until REN is deasserted. In POS-PHY L3 mode, RVAL goes low if the selected port is empty or at the end of a packet if the minimum deassertion time is greater than zero. RVAL will remain deasserted for the programmable minimum deassertion time. In UTOPIA L3 mode, this signal is held low. In POS-PHY L2 mode, this signal is driven when one of the ports is selected for data transfer, and tri-stated when REN is deasserted, none of the ports is selected or data path reset is active. In UTOPIA L2 (reset default) mode this signal is tri-stated. In all UTOPIA L3 or POS-PHY L3 modes this signal is driven. Oz Receive Packet Data Modulus [1:0] (Tri-State). This signal is tri-state when global reset is applied. RMOD[1:0]: In POS-PHY L2 or POS-PHY L3 modes, this signal is used to indicate the number of valid bytes on the RDATA bus. RMOD[1:0]=00 RDATA[31:0] valid RMOD[1:0]=01 RDATA[31:8] valid RMOD[1:0]=10 RDATA[31:16] valid RMOD[1:0]=11 RDATA[31:24] valid This signal is updated on the rising edge of RSCLK. RMOD is only valid when REOP is high. In UTOPIA L3, 8-bit POS-PHY L2 or 8-bit POS-PHY L3 modes, RMOD[1:0] signals are held low. In 16-bit POS-PHY L2 or 16 bit POS-PHY L3 modes, RMOD[1] is held low. In POS-PHY L2 mode, these signals are driven when one of the ports is selected for data transfer, and tri-stated when REN is deasserted, none of the ports is selected or data path reset is active. In UTOPIA L2 (reset default) mode these signals are tri-stated. In UTOPIA L3 or POS-PHY L3 modes these signals are driven. Oz Receive Packet Error (Tri-State). This signal is tri-state when global reset is applied. RERR: In POS-PHY L2 or POS-PHY L3 modes, this signal is used to indicate that the current packet is erred. When RERR is high, the current packet should be aborted. This signal is updated on the rising edge of RSCLK. RERR is only valid when REOP is high. In UTOPIA L3 mode this signal is held low. In POS-PHY L2 mode, this signal is driven when one of the ports is selected for data transfer, and tri-stated when REN is deasserted, none of the ports is selected or data path reset is active. In UTOPIA L2 (reset default) mode this signal is tri-stated. In UTOPIA L3 or POS-PHY L3 modes, this signal is driven. 62 DS3181/DS3182/DS3183/DS3184 PIN TYPE FUNCTION MICROPROCESSOR INTERFACE D[15:0] IO A[10:1] I A[0] / BSWAP ALE I CS I RD / DS I WR / R/W I RDY Oz INT Oz MODE I WIDTH I Bidirectional 16- or 8-Bit Data Bus This bus is tri-state when RST pin is low or CS pin is high. D[15:0]: A 16-bit or 8-bit data bus used to input data during register writes, and data outputs during register reads. The upper 8 bits are not used and never driven in 8-bit bus mode. Weak pullup resistors or bus holders should be used for each pin. Address Bus (minus LSB) A[10:1]: identifies the specific 16 bit registers, or group of 8 bit registers, being accessed. A[10] must be tied to ground for the DS3181 and DS3182 versions. Address Bus LSB / Byte Swap A[0]: This signal is connected to the lower address bit in 8-bit systems. (WIDTH=0) 1 = Output register bits 15:8 on D[7:0], D[15:8] not driven 0 = Output register bits 7:0 on D[7:0], D[15:8] not driven BSWAP: This signal is tied high or low in 16-bit systems. (WIDTH=1) 1 = Output register bits 15:8 on D[7:0], 7:0 on D[15:8] 0 = Output register bits 7:0 on D[7:0], 15:8 on D[15:8] Address Latch Enable ALE: This signal is used to latch the address on the A[10:0] pins in multiplexed address systems. When it is high the address is fed through the address latch to the internal logic. When it transitions to low, the address is latched and held internally until the signal goes back high. ALE should be tied high for non-multiplexed address systems. Chip Select (active low) CS: This signal must be low during all accesses to the registers Read Strobe (active low) / Data Strobe (active low) RD: Read Strobe mode (MODE=0): RD is low during a register read. DS: Data Strobe mode (MODE=1): DS is low during either a register read or a write. Write Strobe (active low) / R/W Select WR: Write Strobe mode (MODE=0): WR is low during a register write. R/W: Data Strobe mode (MODE=1): R/W is high during a register read cycle, and low during a register write cycle. Ready Handshake (active low) RDY: This ready signal is driven low when the current read or write cycle is in progress. When the current read or write cycle is not ready it is driven high. When device is not selected, it is not driven. Interrupt (active low) This signal is tri-state when RST pin is low. INT: This interrupt signal is driven low when an event is detected on any of the enabled interrupt sources in any of the register banks. When there are no active and enabled interrupt sources, the pin can be programmed to either drive high or not drive high. The reset default is to not drive high when there are no active and enabled interrupt source. All interrupt sources are disabled when RST=0 and they must be programmed to be enabled. Mode Select RD/WR or DS Strobe Mode MODE: 1 = Data Strobe Mode, 0 = Read/Write Strobe Mode Data Bus Width Select 8- or 16-Bit Interface WIDTH: 1 = 16-bits, 0 = 8 bits 63 DS3181/DS3182/DS3183/DS3184 PIN TYPE FUNCTION MISC I/O GPIO1 IO GPIO2 IO GPIO3 IO GPIO4 IO GPIO5 IO GPIO6 IO GPIO7 IO GPIO8 IO TEST I HIZ I RST I General-Purpose IO 1 GPIO1: This signal is configured to be a general-purpose IO pin, or an alarm output signal for port 1. This pin is an input after reset and should have a pullup resistor on it if not connected to a signal or programmed as an output. General-Purpose IO 2 GPIO2: This signal is configured to be a general-purpose IO pin, or the 8KREFO output signal, or an alarm output signal for port 1. This pin is an input after reset and should have a pullup resistor on it if not connected to a signal or programmed as an output. General-Purpose IO 3 GPIO3: This signal is configured to be a general-purpose IO pin, or an alarm output signal for port 2. This pin is an input after reset and should have a pullup resistor on it if not connected to a signal or programmed as an output. General-Purpose IO 4 GPIO4: This signal is configured to be a general-purpose IO pin, or the 8KREFI input signal, or an alarm output signal for port 2. When configured for 8KREFI mode the signal frequency should be 8,000 Hz +/- 500 ppm and about 50% duty cycle. This pin is an input after reset and should have a pullup resistor on it if not connected to a signal or programmed as an output. General-Purpose IO 5 GPIO5: This signal is configured to be a general-purpose IO pin, or an alarm output signal for port 3. This pin is an input after reset and should have a pullup resistor on it if not connected to a signal or programmed as an output. General-Purpose IO 6 GPIO6: This signal is configured to be a general-purpose IO pin, or the TMEI input signal, or an alarm output signal for port 3. When configured for TMEI input, the signal low time and high time must be greater than 500ns. This pin is an input after reset and should have a pullup resistor on it if not connected to a signal or programmed as an output. General-Purpose IO 7 GPIO7: This signal is configured to be a general-purpose IO pin, or an alarm output signal for port 4. This pin is an input after reset and should have a pullup resistor on it if connected to a signal or programmed as an output. General-Purpose IO 8 GPIO8: This signal is configured to be a general-purpose IO pin, or the PMU input signal, or an alarm output signal for port 4. When configured for PMU input, the signal low time and high time must be greater than 500ns. This pin is an input after reset and should have a pullup resistor on it if not connected to a signal or programmed as an output. Test Enable (active low) TEST: This signal enables the internal scan test mode when low. For normal operation tie high. This is an asynchronous input. High-Impedance Test Enable (active low) HIZ: This signal puts all digital output and bidirectional pins in the high-impedance state when it low and JTRST is low. For normal operation tie high. This is an asynchronous input. Reset (active low) RST: This signal resets all the internal processor registers and logic when low. Global and port data path resets are enabled and port power-downs are enabled. This pin should be low while power is applied and set high after the power is stable. This is an asynchronous input. 64 DS3181/DS3182/DS3183/DS3184 PIN TYPE FUNCTION JTAG JTCLK I JTMS Ipu JTDI Ipu JTDO Oz JTRST Ipu JTAG Clock JTCLK: This clock input is typically a low frequency (less than 10 MHz) 50% duty cycle clock signal. JTAG Mode Select (with pullup) JTMS: This input signal is used to control the JTAG controller state machine and is sampled on the rising edge of JTCLK. JTAG Data Input (with pullup) JTDI: This input signal is used to input data into the register that is enabled by the JTAG controller state machine and is sampled on the rising edge of JTCLK. JTAG Data Output JTDO: This output signal is the output of an internal scan shift register enabled by the JTAG controller state machine and is updated on the falling edge of JTCLK. The pin is in the high impedance mode when a register is not selected or when the JTRST signal is high. The pin goes into and exits the high impedance mode after the falling edge of JTCLK JTAG Reset (active low with pullup) JTRST: This input forces the JTAG controller logic into the reset state and forces the JTDO pin into high impedance when low. This pin should be low while power is applied and set high after the power is stable. The pin can be driven high or low for normal operation, but must be high for JTAG operation. CLAD CLKA CLKB CLKC I Clock A CLKA: This clock input is a DS3 signal (44.736MHz 20ppm) when the CLAD is disabled or it is one of the CLAD reference clock signals when the CLAD is enabled. IO Clock B CLKB: This pin is a E3 (34.368 MHz 20 ppm) input signal when the CLAD is disabled (reset default) or it can be enabled to output a generated clock when the CLAD is enabled. The pin is driven low when it is not selected to output a clock signal and the CLAD is enabled. See Table 10-11. IO Clock C CLKC: This pin is a STS-1 (51.84 MHz 20ppm) input signal when the CLAD is disabled or it can be enabled to output a generated clock when the CLAD is enabled. The pin is driven low when it is not selected to output a clock signal and the CLAD is enabled. See Table 10-11. POWER VSS PWR Ground, 0V potential. Common to digital core, digital IO and all analog circuits. VDD PWR Digital 3.3V. Common to digital core and digital IO. AVDDRn PWR Analog 3.3V for receive LIU on port n. Powers receive LIU on port n. AVDDTn PWR Analog 3.3V for transmit LIU on port n. Powers transmit LIU on port n. AVDDJn PWR Analog 3.3V for jitter attenuator on port n. Powers jitter attenuator on port n. AVDDC PWR Analog 3.3V for CLAD. Powers clock rate adapter common to all ports. 65 DS3181/DS3182/DS3183/DS3184 8.3 Pin Functional Timing 8.3.1 Line IO 8.3.1.1 B3ZS/HDB3/AMI Mode Transmit Pin Functional Timing There is no suggested time alignment between the TXPn, TXNn and TX LINE signals and the TLCLKn clock signal. The TX DATA signal is not a readily available signal, it is meant to represent the data value of the other signals. The TXPn and TXNn signals are only available when the line is in B3ZS/HDB3 or AMI mode and the LIU is enabled. The TPOSn, TNEGn and TLCLKn signals are only available when the line is in B3ZS/HDB3 or AMI mode and the transmit line pins are enabled. The TPOSn, TNEGn and TLCLKn pins can be enabled at the same as the LIU is enabled. The TPOSn and TNEGn signals change a small delay after the positive edge of the reference clock if the clock pin is not inverted; otherwise they change after the negative edge. The TLCLKn clock pin is the clock reference typically used for the TPOSn and TNEGn signals, but they can be time referenced to the TCLKIn, TCLKOn, RLCLKn or RCLKOn clock pins. The TPOSn and TNEGn pins can be inverted, but the polarity of TXPn and TXNn cannot be inverted. TXPn and TXNn are differential analog output pins. They are biased around 1/2 VDD and pulse above and below the bias voltage by about 1 Volt. These signals are connected to the windings of a 1:2 step down transformer and the other winding of the transformer creates the TX LINE signal. The TX LINE signal is a bipolar signal that pulses about 1 Volt positive and 1 Volt negative above and below ground (0 volts). See Figure 1-1 for a diagram of the external connections. Figure 8-1 and Figure 8-2 shows the relationship between the analog and the digital outputs. Figure 8-1. TX Line IO B3ZS Functional Timing Diagram TLCLK (TX DATA) TPOS TNEG B TXP V B V B V B V BIAS V TXN 0V (TX LINE) + - B3ZS CODEWORD 66 DS3181/DS3182/DS3183/DS3184 Figure 8-2. TX Line IO HDB3 Functional Timing Diagram TLCLK (TX DATA) TPOS B TNEG TXP V B V B V B V BIAS V TXN 0V (TX LINE) + - HDB3 CODEWORD 8.3.1.2 B3ZS/HDB3/AMI Mode Receive Pin Functional Timing There is no suggested time alignment between the RXPn, RXNn and RX LINE signals and the RLCLKn clock signal. The RX DATA signal is not an always readily available signal, it is meant to represent the data value of the other signals. The RXPn and RXNn pins are only available when the line is in B3ZS/HDB3 or AMI mode and the LIU is enabled. The RPOSn, RNEGn and RLCLKn pins are only available when the line is in B3ZS/HDB3 or AMI mode and the LIU is disabled. The RPOSn and RNEGn signals are sampled at the rising edge of the reference clock signal if the clock pin is not inverted; otherwise they are sampled at the negative edge. The RLCLKn clock pin is the clock reference used for the RPOSn and RNEGn signals. The RPOSn and RNEGn pins can be inverted. RXPn and RXNn are differential analog input pins. They are biased around 1/2 VDD and pulse above and below the bias voltage by about 1 Volt with zero cable length. These signals are connected to the windings of a 1:2 step up transformer and the other winding of the transformer is connected to the RX LINE signal. The RX LINE signal is a bipolar signal that pulses about 1 Volt positive and 1 Volt negative above and below ground (0 volts) with zero cable length. See Figure 1-1 for a diagram of the external connections. Figure 8-3 and Figure 8-4 shows the relationship between the analog and the digital outputs. Figure 8-3. RX Line IO B3ZS Functional Timing Diagram RLCLK (RX DATA) RPOS B RNEG RXP V B V B V B V BIAS V RXN 0V (RX LINE) + - B3ZS CODEWORD 67 DS3181/DS3182/DS3183/DS3184 Figure 8-4. RX Line IO HDB3 Functional Timing Diagram RLCLK (RX DATA) RPOS B RNEG RXP V B V B V B V BIAS V RXN 0V (RX LINE) + - HDB3 CODEWORD 8.3.1.3 UNI Mode Transmit Pin Functional Timing The TDATn pin is available when the line interface is in the UNI mode and the transmit line pins are enabled. The TOHMOn and TOHMIn pins are available when the framer is in one of the "- OHM" modes and the transmit line pins are enabled. The line interface is forced into the UNI mode when the framer is in one of the "- OHM" modes. The TOHMIn pin is used to control the insertion of gaps in the data by stopping the internal formatters and data sources. These gaps are inserted where external logic will add more overhead bits to the signal. The TOHMOn signal is delayed from the TOHMIn signal by three clock periods. The TOHMOn signal aligns to the TDATn signal and is high when internal framing and signal source has stopped inserting data. The TDATn signal should be ignored when TOHMOn is high. In the "- OHM Octet" framing modes, the first payload bit after the TOHMOn signal goes low is the MSB (Bit 1) of a payload Octet. The TDATn and TOHMOn signals change a small delay after the positive edge of the reference clock signal if the clock pin is not inverted, other wise they change after the negative edge. The TOHMIn signal is sampled at the rising edge of the reference clock signal if the clock pin is not inverted; otherwise it is sampled at the negative edge. The TLCLKn clock pin is the clock reference typically used for the TDATn, TOHMOn and TOHMIn signals, but they can be time referenced to the TCLKIn, TCLKOn, RLCLKn or RCLKOn clock pins. The TDATn, TOHMOn, and TOHMIn pins can be inverted. See Figure 8-5 and Figure 8-6 Figure 8-5. TX Line IO UNI OHM Functional Timing Diagram TLCLK TDAT TDAT GAP FOR EXT OVERHEAD INSERTION TOHMO TOHMI Figure 8-6. TX Line IO UNI Octet Aligned OHM Functional Timing Diagram TLCLK TDAT B6 B7 B8 Octet n EXT OH BIT LOCATIONS B1 B2 B3 B4 B5 B6 B7 B8 B1 ATM Cell /Packet Octet n+1 TOHMO TOHMI 68 DS3181/DS3182/DS3183/DS3184 8.3.1.4 UNI Mode Receive Pin Functional Timing The RDATn pin is available when the line interface is in the UNI mode. The ROHMIn pin is available when the framer is in one of the "-OHM" modes. The RLCVn pin is available when the line interface is in the UNI mode and the framer is not in one of the "-OHM" modes. The line interface is forced into the UNI mode when the framer is in one of the "-OHM" modes. The ROHMIn pin is used to mark the RDATn bits that will be ignored by the internal receive logic. When the ROHMIn pin is high, the internal framers and data sinks will ignore the corresponding RDATn bits. In the "- OHM Octet" framing modes, the data on RDATn is octet aligned with the ROHMIn signal, the first bit of the serial data on RDATn is the MSB (Bit 1) of a payload Octet. All bits on the RDATn pin, even the bits that are marked by ROHMIn, will come out the RSERn pin, if the RSERn pin is enabled. The signal on the RLCVn pin enables the BPV counter, which is in the line interface, to increment each clock it is high. The RDATn, ROHMIn and RLCVn signals are sampled at the rising edge of the reference clock signal if the clock pin is not inverted; otherwise they are sampled at the negative edge. The RLCLKn clock pin is the clock reference used for the RDATn, ROHMIn and RLCVn signals. The RDATn, ROHMIn and RLCVn pins can be inverted. See Figure 8-7 and Figure 8-8. Figure 8-7. RX Line IO OHM UNI Functional Timing Diagram RLCLK RDAT RDAT DATA WILL BE IGNORED ROHM RLVC INC BPV COUNTER TWICE INC BPV COUNTER ONCE Figure 8-8. RX Line IO UNI Octet Aligned OHM Functional Timing Diagram RLCLK B6 B7 B8 Octet n RDAT EXT OH BIT LOCATIONS B1 B2 B3 B4 B5 B6 B7 B8 B1 ATM Cell /Packet Octet n+1 ROHM 8.3.2 DS3/E3 Framing and PLCP Overhead Functional Timing Figure 8-9 shows the relationship of the DS3 receive-overhead port pins. Figure 8-9. DS3 Framing Receive Overhead Port Timing ROHCLK ROHSOF ROH F73 1 C73 2 F74 3 X1 4 F11 5 C11 6 F12 7 C12 8 F13 9 C13 10 F14 11 69 X2 12 F21 13 C21 14 F22 15 C22 16 F23 17 C23 18 F24 19 P1 20 F31 21 C31 22 F32 23 C32 24 DS3181/DS3182/DS3183/DS3184 Figure 8-10 shows the relationship of the E3 G.751 receive-overhead port pins. Figure 8-10. E3 G.751 Framing Receive Overhead Port Timing ROHCLK ROHSOF ROH FAS 10 A 1 FAS 1 N 2 3 FAS 3 FAS 2 4 5 FAS 4 6 FAS 5 7 8 FAS 6 9 FAS 7 10 FAS 8 FAS 9 11 FAS 10 12 13 FAS 1 A N 14 15 FAS 2 16 17 FAS 3 18 FAS 4 19 FAS 5 20 FAS 6 21 FAS 8 22 FAS 9 23 FAS 10 24 Figure 8-11 shows the relationship of the E3 G.832 receive-overhead port pins. Figure 8-11. E3 G.832 Framing Receive Overhead Port Timing ROHCLK ROHSOF ROH GC 6 GC 7 1 FA1 1 GC 8 2 3 FA1 3 FA1 2 4 5 FA1 4 6 FA1 5 7 8 FA1 6 9 FA1 7 10 FA1 8 FA2 1 11 FA2 2 12 13 FA2 3 14 FA2 4 FA2 5 15 16 FA2 6 17 FA2 7 18 FA2 8 19 EM 1 20 EM 2 21 EM 3 22 EM 4 23 EM 5 24 Figure 8-12 shows the relationship of the DS3 transmit-overhead port pins. Figure 8-12. DS3 Framing Transmit Overhead Port Timing TOHCLK TOHSOF TOHEN TOH F73 C73 F74 1 2 3 X1 4 F11 5 C11 F12 C12 F13 C13 6 7 8 9 10 F14 X2 11 12 F21 13 C21 14 F22 15 C22 16 F23 17 C23 F24 18 19 P1 20 F31 C31 21 22 F32 23 C32 24 Figure 8-13 shows the relationship of the E3 G.751 transmit-overhead port pins. Figure 8-13. E3 G.751 Framing Transmit Overhead Port Timing TOHCLK TOHSOF TOHEN TOH FAS 10 1 A 2 N 3 FAS 1 FAS 2 FAS 3 FAS 4 FAS 5 FAS 6 FAS 7 FAS 8 FAS 9 FAS 10 4 5 6 7 8 9 10 11 12 13 70 A N 14 15 FAS 1 FAS 2 FAS 3 FAS 4 FAS 5 FAS 6 FAS 8 FAS 9 FAS 9 16 17 18 19 20 21 22 23 24 DS3181/DS3182/DS3183/DS3184 Figure 8-14 shows the relationship of the E3 G.832 transmit-overhead port pins. Figure 8-14. E3 G.832 Framing Transmit Overhead Port Timing TOHCLK TOHSOF TOHEN TOH GC 6 GC 7 GC 8 FA1 1 FA1 2 FA1 3 FA1 4 FA1 5 FA1 6 1 2 3 4 5 6 7 8 9 FA1 7 10 FA1 8 11 FA2 1 12 FA2 2 FA2 3 FA2 4 FA2 5 FA2 6 FA2 7 FA2 8 13 14 15 16 17 18 19 20 21 22 23 24 Z5 7 Z5 8 Z4 1 Z4 2 Z4 3 Z4 4 Z4 5 EM 1 EM 2 EM 3 EM 4 EM 5 Figure 8-15 shows the relationship of the DS3 PLCP receive-overhead port pins. Figure 8-15. DS3 PLCP Receive Overhead Port Timing RPOHCLK RPOHSOF RPOH C1 6 1 C1 7 2 C1 8 3 Z6 1 4 Z6 2 5 Z6 3 6 Z6 4 7 Z6 5 8 Z6 6 9 Z6 7 10 Z5 1 Z6 8 11 12 Z5 2 13 Z5 3 14 Z5 4 Z5 5 15 16 Z5 6 17 18 19 20 21 22 23 24 Figure 8-16 shows the relationship of the E3 G.751 PLCP receiver-overhead port pins. Figure 8-16. E3 G.751 PLCP Receive Overhead Port Timing RPOHCLK RPOHSOF RPOH C1 6 1 C1 7 2 C1 8 3 Z3 1 4 Z3 2 5 Z3 3 6 Z3 4 7 Z3 5 8 Z3 6 9 Z3 7 10 Z2 1 Z3 8 11 12 Z2 2 13 Z2 3 14 Z2 4 15 Z2 5 16 Z2 6 17 Z2 7 Z2 8 Z1 1 Z1 2 Z1 3 Z1 4 Z1 5 18 19 20 21 22 23 24 Figure 8-17 shows the relationship of the DS3 PLCP transmit-overhead port pins. Figure 8-17. DS3 PLCP Transmit Overhead Port Timing TPOHCLK TPOHSOF TPOHEN TPOH C1 6 C1 7 C1 8 1 2 3 Z6 1 4 Z6 2 Z6 3 Z6 4 Z6 5 Z6 6 5 6 7 8 9 Z6 7 Z6 8 Z5 1 Z5 2 Z5 3 Z5 4 Z5 5 Z5 6 Z5 7 Z5 8 Z4 1 Z4 2 Z4 3 Z4 4 Z4 5 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 71 DS3181/DS3182/DS3183/DS3184 Figure 8-18 shows the relationship of the E3 G.751 PLCP transmit-overhead port pins. Figure 8-18. E3 G.751 PLCP Transmit Overhead Port Timing TPOHCLK TPOHSOF TPOHEN TPOH 8.3.3 C1 6 C1 7 C1 8 1 2 3 Z3 2 Z3 3 5 6 Z3 1 4 Z3 4 7 Z3 5 Z3 6 8 9 Z3 7 Z3 8 Z2 1 Z2 2 Z2 3 Z2 4 Z2 5 Z2 6 Z2 7 Z2 8 Z1 1 Z1 2 Z1 3 Z1 4 Z1 5 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Internal (IFRAC) and External (XFRAC) Fractional DS3/E3 Overhead Functional Timing The fractional overhead pins provide the ability to insert bits in the DS3/E3 payload that are not used for cells or packets. The source of fractional overhead bits is controlled by an internal register (see FRAC.TCR), specifying internal generation or external sourcing via the TFOHENIn pin. The allocation of DS3/E3 payload used for cell and packet data is also programmable or controlled by the TFOHENIn pin. The TSOFIn, TSOFOn, TDENn, RSOFOn and RDENn pins are used to determine which bit positions are DS3/E3 overhead so that fractional overhead bits will be inserted only in DS3/E3 payload. The TCLKOn and RCLKOn clocks can be configured for gapped modes that will toggle for each fractional overhead bit, allowing a simple way of using the overhead bits for messaging. Figure 8-19 shows the timing with the external fractional transmit port pins. P designates payload bits, F designates fractional overhead, and L designates DS3/E3 overhead, based on TDEN. Figure 8-19. External (XFRAC) Transmit Fractional Timing TCLKI or TCLKO TFOHENI PX5 PX6 TFOH PX5 PX6 FX1 FX2 FX3 1 2 3 4 5 L1 P11 P12 P13 P14 P15 P16 L1 P11 P12 P13 P14 P15 P15 7 8 9 F11 F12 F13 L2 P21 P22 P23 P24 P25 P26 L2 P21 P22 P23 P24 P25 P26 F21 F22 TSOFI TSOFO TDEN 6 10 11 12 13 14 15 16 17 18 19 20 21 22 23 L2 P21 P22 P23 P23 P24 P25 P26 24 Figure 8-20 shows the timing with the external fractional receive port pins. Figure 8-20. External (XFRAC) Receive Fractional Timing RCLKI or RCLKO RFOHENI PY3 PY4 PY5 PY6 L1 P11 P12 P13 P14 P15 P16 P13 P14 P15 P16 F11 F12 F13 RDEN RSER PY4 PY5 PY6 FY1 FY2 FY3 1 2 3 4 5 6 L1 P11 P12 8 9 L2 P21 P22 F21 RSOF 7 10 11 72 12 13 14 15 16 17 18 19 20 21 22 23 24 DS3181/DS3182/DS3183/DS3184 Figure 8-21 shows the timing with the internal fractional transmit port pins. Figure 8-21. Internal (IFRAC) Transmit Fractional Timing TCLKI or TCLKO TGCLK TFOHENO TFOH X X 1 X 2 X 3 FOH 4 FOH 5 FOH 6 X 7 X 8 X 9 X 10 X 11 X 12 X 13 FOH FOH 14 15 FOH X X X X X X 16 17 18 19 20 21 22 X X X X X X X 16 17 18 19 20 21 22 X FOH 23 24 FOH FOH 23 24 Figure 8-22 shows the timing with the internal fractional transmit port pins. Figure 8-22. Internal (IFRAC) Receive Fractional Timing RCLKI or RCLKO RGCLK RFOHENO RSER X X 1 8.3.4 X 2 FOH FOH FOH 3 4 5 X 6 X 7 X 8 X 9 X X X 10 11 12 FOH FOH FOH 13 14 15 Flexible Fractional (FFRAC) DS3/E3 Overhead Interface Functinal Timing The Flexible fractional mode provides the capability to modify the payload data from the cell/packet processor before inserting it into the DS3 or E3 payload. The bit rate of the payload from the cell/packet processor can be less than the DS3 or E3 payload bit rate. The interface to the DS3 or E3 payload uses the TSOFIn, TSOFOn, TDENn, TSERn, RSOFOn, RDENn and RSERn pins. The interface to the cell/packet processor uses the TPDENIn, TPDENOn, TPDATn, RPDENIn and RPDATn pins. The TPDENIn pin is used to determine the bit rate of the transmit cell/packet payload data. The TPDENOn pin is high when the data on TPDATn is valid. The delay between TPDENIn and TPDENOn is three clocks. The RPDENIn pin is used to determine the bit rate of the receive cell/packet processor data. The cell/packet processor uses the cell/packet data on the RPDATn pin when the RPDENIn pin is high. 73 DS3181/DS3182/DS3183/DS3184 Figure 8-23 shows the timing with the flexible fractional transmit port pins. Figure 8-23. Transmit Flexible Fractional (FFRAC) Timing TCLKI or TCLKO TPDENI TPDENO TPDAT P14 P1 P2 P3 P4 P5 P6 FPx FPy FPz FOx FOy FOz P8 P9 P10 P11 P12 FP5 FP6 FO1 FO2 FO3 P13 P14 P15 P16 P17 FP11 FP12 FO4 FO5 TSOFI TSOFO TDEN TSER 1 2 3 4 5 OH1 6 FP1 7 FP2 8 FP3 9 FP4 10 11 12 13 14 15 OH2 16 FP7 17 FP8 18 19 FP9 FP10 20 21 22 23 24 Figure 8-24 shows the timing with the flexible fractional receive port pins. Figure 8-24. Receive Flexible Fractional (FFRAC) Timing RCLKI or RCLKO RSOFO RDEN RSER FP4 FP5 FP6 FO1 FO2 FO3 P2 P3 P4 P5 P6 OH1 FP7 FP8 FP9 FP10 FP11 FP12 FO4 FO5 FO6 P7 P8 P9 P10 P11 P12 OH2 FP13 FP14 FP15 FP16 FP17 FP18 FP19 P13 P14 P15 P16 RPDENI RSER X P1 1 2 3 4 5 6 X 7 8 9 10 11 12 13 74 14 15 16 17 X 18 19 20 21 22 23 24 DS3181/DS3182/DS3183/DS3184 8.3.5 UTOPIA/POS-PHY/SPI-3 System Interface Functional Timing 8.3.5.1 UTOPIA Level 2 Functional Timing Figure 8-25 shows a multidevice transmit-interface multiple cell transfer to different PHY devices. On clock edge 2, the ATM device places address `00h' on the address bus (which is mapped to Port 1). PHY device '1' (Port 1) indicates to the ATM device that it can accept cell data by asserting TDXA[1]. On clock edge 4, the ATM device selects PHY device '1'. On clock edge 5, the ATM device starts a cell transfer to PHY device '1' by asserting TEN, placing the first byte of cell data on TDATA, and asserting TSOX to indicate the transfer of the first byte of the cell. On clock edge 6, the ATM device deasserts TSOX as it continues to place additional bytes of the cell on TDATA.. On clock edge 13, PHY device `2' asserts TDXA[2] to indicate to the ATM device that it is ready to accept cell data. On clock edge 15, PHY device '1' indicates that it cannot accept the transfer of a complete cell by deasserting TDXA[1]. On clock edge 16, the ATM device deselects PHY device '1' and selects PHY device '2' by deasserting TEN and placing PHY device '2's address on TADR. On clock edge 17, the ATM device starts the transfer of a cell to PHY device '2' by asserting TEN, placing the first byte of cell data on TDATA, and asserting TSOX to indicate the transfer of the first byte of the cell. On clock edge 18, the ATM device deasserts TSOX as it continues to place additional bytes of the cell on TDATA. Figure 8-25. UTOPIA Level 2 Transmit Cell Transfer Direct Mode TCLK TADR 00h 01h TDXA[1] TDXA[2] TDXA[3] TDXA[4] TEN TDATA H1 H2 H3 ... P42 8 9 P43 P44 P45 P46 P47 P48 H1 H2 H3 H4 TSOX Transfer Cell To: PORT 1 1 2 3 4 5 6 7 10 75 11 PORT 2 12 13 14 15 16 17 18 19 20 DS3181/DS3182/DS3183/DS3184 Figure 8-26 shows a multidevice transmit-interface multiple cell transfer to different PHY devices. On clock edge 2, the ATM device places address `00h' on the address bus (which is mapped to Port 1). PHY device '1' (Port 1) indicates to the ATM device that it has a complete cell to send by asserting RDXA[1]. On clock edge 4, the ATM device selects PHY device '1'. On clock edge 5, the ATM device asserts REN. On clock edge 6, the PHY device `1' starts a cell transfer to the ATM device by placing the first byte of cell data on RDATA, and asserting RSOX to indicate the transfer of the first byte of the cell. On clock edge 7, the PHY device deasserts RSOX as it continues to place additional bytes of the cell on RDATA. On clock edge 13, PHY device `2' asserts RDXA[2] to indicate to the ATM device that it is ready to send a cell. On clock edge 15, PHY device '1' indicates that it cannot transfer a complete cell by deasserting RDXA[1]. On clock edge 16, the ATM device deselects PHY device '1' and selects PHY device '2' by deasserting REN and placing PHY device '2's address on RADR. On clock edge 17, the ATM device asserts REN. On clock edge 18, PHY device `2' (Port 2) starts the transfer of a cell to the ATM device by placing the first byte of cell data on RDATA, and asserting RSOX to indicate the transfer of the first byte of the cell. On clock edge 18, the PHY device deasserts RSOX as it continues to place additional bytes of the cell on RDATA. Figure 8-26. UTOPIA Level 2 Receive Cell Transfer Direct Mode RSCLK RADR 00h 01h RDXA[1] RDXA[2] RDXA[3] RDXA[4] REN RDATA H1 H2 ... H3 P42 P43 P44 P45 P46 P47 P48 H1 H2 H3 RSOX Transfer Cell From: PORT 1 1 2 3 4 5 6 7 8 9 10 11 12 PORT 2 13 14 15 16 17 18 19 20 Figure 8-27 shows a multidevice transmit-interface multiple cell transfer to different PHY devices. On clock edge 2, the ATM device polls PHY device 'N'. On clock edge 3, PHY device 'N' indicates to the ATM device that it can accept cell data by asserting TPXA. On clock edge 4, the ATM device selects PHY device 'N'. On clock edge 5, the ATM device starts a cell transfer to PHY device 'N' by asserting TEN, placing the first byte of cell data on TDATA, and asserting TSOX to indicate the transfer of the first byte of the cell. On clock edge 6, the ATM device deasserts TSOX as it continues to place additional bytes of the cell on TDATA. On clock edge 6, the ATM device also polls PHY device 'O'. On clock edge 7, PHY device 'O' indicates that it can accept the transfer of a complete cell. On clock edge 14, the ATM device polls PHY device 'N'. On clock edge 15, PHY device 'N' indicates that it cannot accept the transfer of a complete cell. On clock edge 16, the ATM device deselects PHY device 'N' and selects PHY device 'O' by deasserting TEN and placing PHY device 'O's address on TADR. On clock edge 17, the ATM device starts the transfer of a cell to PHY device 'O' by asserting TEN, placing the first byte of cell data on TDATA, and asserting TSOX to indicate the transfer of the first byte of the cell. On clock edge 18, the ATM device deasserts TSOX as it continues to place additional bytes of the cell on TDATA. 76 DS3181/DS3182/DS3183/DS3184 Figure 8-27. UTOPIA Level 2 Transmit Multiple Cell Transfer Polled Mode TCLK TADR M TPXA 1F N 1F M N 1F N O 1F N ... 1F O L P 1F M 1F L M N 1F O 1F N O P42 P43 P44 P45 P46 P47 P48 H1 P 1F L P TEN TDATA H1 H2 H3 5 6 7 ... H2 H3 H4 19 20 TSOX Transfer Cell To: 1 2 3 4 8 N 10 9 O 11 12 13 14 15 16 17 18 Figure 8-28 shows a multidevice receive-interface multiple cell transfer from different PHY devices. On clock edge 2, the ATM device polls PHY device 'N'. On clock edge 3, PHY device 'N' indicates to the ATM device that it has a complete cell ready for transfer by asserting RPXA. On clock edge 4, the ATM device selects PHY device 'N'. On clock edge 5, the ATM device asserts REN. On clock edge 6, PHY device 'N' starts a cell transfer by placing the first byte of cell data on RDATA, and asserting RSOX to indicate the transfer of the first byte of the cell. On clock edge 7, PHY device 'N' deasserts RSOX as it continues to place additional bytes of the cell on RDATA. On clock edge 12, the ATM device polls PHY device 'O'. On clock edge 13, PHY device 'O' indicates to the ATM device that it has a complete cell ready for transfer by asserting RPXA. On clock edge 16, the ATM device deselects PHY device 'N' and selects PHY device 'O' by deasserting REN and placing PHY device 'O's address on RADR. On clock edge 17, the ATM device asserts REN and PHY device 'N' stops transferring cell data and tri-states its RDATA and RSOX outputs. On clock edge 18, PHY device 'O' starts a cell transfer by placing the first byte of cell data on RDATA, and asserting RSOX to indicate the transfer of the first byte of the cell. On clock edge 19, PHY device 'O' deasserts RSOX as it continues to place additional bytes of the cell on RDATA. Figure 8-28. UTOPIA Level 2 Receive Multiple Cell Transfer Polled Mode RCLK RADR M 1F RPXA M N 1F N N 1F O N 1F ... O 1F M L 1F O M 1F P O 1F O P 1F N O 1F P N REN H1 RDATA H2 ... P41 P42 P43 P44 P45 P46 P47 P48 8 9 H1 H2 H3 RSOX Transfer Cell From: N 1 2 3 4 5 6 7 10 11 O 12 13 14 15 16 17 18 19 20 Figure 8-29 shows a multidevice receive-interface unexpected multiple cell transfer. Prior to clock edge 1, the cell transfer was started. On clock edge 4, since no other PHY device has a cell ready for transfer, the ATM device assumes another cell transfer from PHY device 'N' and leaves REN asserted. On clock edge 5, PHY device 'N' stops transferring cell data and indicates that it does not have another cell ready for transfer by not asserting RSOX. On clock edge 6, the ATM device deasserts REN to end the cell transfer process. At the same time, PHY device 'N' indicates to the ATM device that it now has a complete cell ready for transfer by placing the first byte of cell data on RDAT, and asserting RSOX to indicate the transfer of the first byte of the cell. On clock edge 7, PHY device 'N' tri-states its RDAT and RSOX outputs because REN is deasserted. On clock edge 8, the ATM device selects PHY device 'N'. On clock edge 9, the ATM device asserts REN. On clock edge 10, PHY device 'N' continues the cell transfer by placing the second byte of cell data on RDAT, and deasserting RSOX. 77 DS3181/DS3182/DS3183/DS3184 Figure 8-29. UTOPIA Level 2 Receive Unexpected Multiple Cell Transfer RCLK RADR L 1F RPXA M 1F L N 1F M O 1F N N 1F O P 1F N L 1F P M 1F L O 1F M P 1F O L P REN* RDAT P45 P46 P47 P48 H1 X RSOX H3 H4 P1 P2 P3 P4 P5 P6 P7 P8 N Transfer Cell From: 8.3.5.2 H2 N 1 N 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 UTOPIA Level 3 Functional Timing Figure 8-30 shows a multiport transmit-interface multiple cell transfer to different PHY devices. PHY port '1', `3', `4' indicate to the ATM device that they can accept cell data by asserting the TDXA[n]. On clock edge 2, the ATM device selects PHY port '1' by putting address `00h' on the address bus. On clock edge 5, the ATM device starts a cell transfer to PHY port '1' by asserting TEN, placing the first byte of cell data on TDATA, and asserting TSOX to indicate the transfer of the first byte of the cell. On clock edge 6, the ATM device deasserts TSOX as it continues to place additional bytes of the cell on TDATA. On clock edge 13, PHY port `2' asserts TDXA[2] to indicate it is ready to accept a cell. On clock edge 15, PHY port `1' deasserts TDXA[1] to indicate to the ATM device that it does not have the availability to receive another complete cell. On clock edge 16, the ATM device selects PHY port '2' by deasserting TEN and placing PHY port '2's address on TADR. On clock edge 17, the ATM device starts the transfer of a cell to PHY port '2' by asserting TEN, placing the first byte of cell data on TDATA, and asserting TSOX to indicate the transfer of the first byte of the cell. On clock edge 18, the ATM device deasserts TSOX as it continues to place additional bytes of the cell on TDATA. Figure 8-30. UTOPIA Level 3 Transmit Multiple Cell Transfer Direct Mode TSCLK TADR 00h 01h TDXA[1] TDXA[2] TDXA[3] TDXA[4] TEN TDATA H1 H2 H3 ... P42 8 9 P43 P44 P45 P46 P47 P48 H1 H2 H3 H4 TSOX Transfer Cell To: PORT 1 1 2 3 4 5 6 7 10 78 11 PORT 2 12 13 14 15 16 17 18 19 20 DS3181/DS3182/DS3183/DS3184 Figure 8-31 shows a multiport transmit-interface multiple cell transfer to different PHY devices. On clock edge 1, the ATM device polls PHY port 'N'. On clock edge 3, PHY port 'N' indicates to the ATM device that it can accept cell data by asserting TPXA. On clock edge 5, the ATM device selects PHY port 'N'. On clock edge 6, the ATM device starts a cell transfer to PHY port 'N' by asserting TEN, placing the first byte of cell data on TDATA, and asserting TSOX to indicate the transfer of the first byte of the cell. On clock edge 7, the ATM device deasserts TSOX as it continues to place additional bytes of the cell on TDATA. On clock edge 11, the ATM device polls PHY port 'M'. On clock edge 12, the ATM device polls PHY port 'N'. On clock edge 13, PHY port 'M' indicates that it can accept the transfer of a complete cell. On clock edge 14, PHY port 'N' indicates that it cannot accept the transfer of a complete cell. On clock edge 16, the ATM device deselects PHY port 'N' and selects PHY port 'M' by deasserting TEN and placing PHY port 'M's address on TADR. On clock edge 17, the ATM device starts the transfer of a cell to PHY port 'M' by asserting TEN, placing the first byte of cell data on TDATA, and asserting TSOX to indicate the transfer of the first byte of the cell. On clock edge 18, the ATM device deasserts TSOX as it continues to place additional bytes of the cell on TDATA. Figure 8-31. UTOPIA Level 3 Transmit Multiple Cell Transfer Polled Mode TCLK TADR M N O P Q N R J K TPXA K L M N O P Q X R X X X X X X H1 H2 H3 ... L M N O P Q M R J K L J K L M N O P Q X R J P43 P44 P45 P46 P47 P48 X H1 H2 H3 P1 ... TEN TDATA ... TSOX Transfer Cell To: N 1 2 3 4 5 6 7 8 9 10 M 11 12 13 14 15 16 17 18 19 20 Figure 8-32 shows a multiport receive-interface multiple cell transfer from different PHY ports. On clock edge 3, PHY port 'N' indicates to the ATM device that it has a complete cell ready for transfer by asserting RPXA. On clock edge 5, the ATM device selects PHY port 'N'. On clock edge 6, the ATM device indicates to PHY port 'N' that it is ready to accept a complete cell transfer by asserting REN. On clock edge 8, PHY port 'N' starts a cell transfer by placing the first byte of cell data on RDATA, and asserting RSOX to indicate the transfer of the first byte of the cell. On clock edge 9, PHY port 'N' deasserts RSOX as it continues to place additional bytes of the cell on RDAT. On clock edge 11, the ATM device polls PHY device 'N'. On clock edge 12, PHY port 'M' indicates to the ATM device that it has a complete cell ready for transfer by asserting RPXA. On clock edge 12, PHY port 'N' indicates to the ATM device that it does not have a complete cell ready for transfer by deasserting RPXA. On clock edge 15, the ATM device deselects PHY port 'N' and selects PHY port 'M' by deasserting REN and placing PHY port 'M's address on RADR. On clock edge 16, the ATM device asserts REN. On clock edge 17, PHY port 'N' stops transferring cell data. On clock edge 18, PHY port 'M' starts a cell transfer by placing the first byte of cell data on RDATA, and asserting RSOX to indicate the transfer of the first byte of the cell. On clock edge 19, PHY port 'M' deasserts RSOX as it continues to place additional bytes of the cell on RDATA. 79 DS3181/DS3182/DS3183/DS3184 Figure 8-32. UTOPIA Level 3 Receive Multiple Cell Transfer Direct Mode RSCLK RADR 00h 01h RDXA[1] RDXA[2] RDXA[3] RDXA[4] REN RDATA H1 H2 ... P42 H3 P43 P44 P45 P46 P47 P48 H1 H2 H3 RSOX Transfer Cell From: PORT 1 1 2 3 4 5 6 7 8 9 10 11 PORT 2 12 13 14 15 16 17 18 19 20 Figure 8-33 shows a multiport receive-interface multiple cell transfer from different PHY ports. On clock edge 1, the ATM device polls PHY port 'N'. On clock edge 3, PHY port 'N' indicates to the ATM device that it has a complete cell ready for transfer by asserting RPXA. On clock edge 5, the ATM device selects PHY port 'N'. On clock edge 6, the ATM device indicates to PHY port 'N' that it is ready to accept a complete cell transfer by asserting REN. On clock edge 8, PHY port 'N' starts a cell transfer by placing the first byte of cell data on RDATA, and asserting RSOX to indicate the transfer of the first byte of the cell. On clock edge 9, PHY port 'N' deasserts RSOX as it continues to place additional bytes of the cell on RDAT. On clock edge 11, the ATM device polls PHY device 'N'. On clock edge 12, PHY port 'M' indicates to the ATM device that it has a complete cell ready for transfer by asserting RPXA. On clock edge 12, PHY port 'N' indicates to the ATM device that it does not have a complete cell ready for transfer by deasserting RPXA. On clock edge 15, the ATM device deselects PHY port 'N' and selects PHY port 'M' by deasserting REN and placing PHY port 'M's address on RADR. On clock edge 16, the ATM device asserts REN. On clock edge 17, PHY port 'N' stops transferring cell data. On clock edge 18, PHY port 'M' starts a cell transfer by placing the first byte of cell data on RDATA, and asserting RSOX to indicate the transfer of the first byte of the cell. On clock edge 19, PHY port 'M' deasserts RSOX as it continues to place additional bytes of the cell on RDATA. Figure 8-33. UTOPIA Level 3 Receive Multiple Cell Transfer Polled Mode RCLK RADR M N O P Q N R J K L RPXA K L M N O P Q N R J ... ... X X X X X X X H1 H2 ... N O P Q M R J K L M L M N O P Q M R J K P43 P44 P45 P46 P47 P48 X H1 H2 P1 REN RDAT RSOX Transfer Cell From: X N 1 2 3 4 5 6 7 8 9 80 10 11 12 M 13 14 15 16 17 18 19 20 DS3181/DS3182/DS3183/DS3184 8.3.5.3 POS-PHY Level 2 Functional Timing Figure 8-34 shows a multidevice transmit interface in byte transfer mode multiple packet transfer to different PHY ports. Prior to clock edge 1, the POS device started a packet transfer to PHY port '1'. On clock edge 2, PHY port '1' deasserts its TDXA to indicate to the POS device that it cannot accept any more data transfers. On clock edge 3, the POS device stops the packet transfer to PHY port '1', and starts a packet transfer to PHY port '2' by leaving TEN asserted, placing PHY port '2's address on TADR, placing the first byte of packet data on TDATA, and asserting TSOX to indicate the transfer of the first byte of the packet. On clock edge 7, PHY port '2' deasserts its TDXA to indicate to the POS device that it cannot accept any more data transfers. On clock edge 8, the POS device stops the packet transfer to PHY port '2', and resumes a packet transfer to PHY port '3'. On clock edge 12, PHY port '2' indicates to the POS device that it can accept a block of packet data by asserting its TDXA. Also, the POS device indicates it is transferring the last byte of packet data by asserting TEOP. On clock edge 13, the POS device ends the packet transfer to PHY port '3', and starts a packet transfer to PHY port '4'. On clock edge 15, PHY port '1' indicates to the POS device that it can accept a block of packet data. On clock edge 17, PHY port '4' deasserts its TDXA to indicate to the POS device that it cannot accept any more data transfers. On clock edge 18, the POS device stops the packet transfer to PHY port '4', and resumes a packet transfer to PHY port '1'. Figure 8-34. Transmit Multiple Packet Transfer to Different PHY ports (direct status mode) TCLK TADR '1' '2' '3' '4' '1' TDXA[1] TDXA[2] TDXA[3] TDXA[4] TEN TDATA P34 P35 P1 P2 ... P41 P42 P19 P20 ... P63 P64 P1 P2 ... P49 P50 P36 P37 P38 TSOX TEOP TERR Transfer To Port '1' 1 '2' 2 3 4 5 '3' 6 7 8 9 10 '4' 11 12 13 14 15 '1' 16 17 18 19 20 Figure 8-35 shows a multidevice receive interface in byte transfer mode multiple packet transfer from different PHY ports/devices. Prior to clock edge 1, a packet data transfer was initiated from PHY port '1', and PHY ports '2', '3', and '4' indicated to the POS device that they have a block of packet data or an end of packet ready for transfer by asserting their RDXA. On clock edge 2, the POS device indicates to PHY port '1' that it cannot accept any more data transfers by removing its address from RADR, and indicates to PHY port '2' that it is ready to accept a block of packet data by placing its address on RADR and leaving REN asserted. On clock edge 3, PHY port '1' stops transferring packet data, and PHY port '2' starts a packet transfer by leaving RVAL asserted, placing the first byte of the packet on RDATA, and asserting RSOX to indicate that this is the first transfer of the packet. On clock edge 4, PHY port '2' deasserts RSOX as it leaves RVAL asserted and continues to place additional bytes of the packet on RDATA. On clock edge 8, the POS device deasserts REN to indicate to PHY port '2' that it cannot accept any more data transfers. On clock edge 9, PHY port '2' ends the packet transfer process by deasserting RVAL and tristating its RVAL, RDATA, RSOX, REOP, and RERR outputs. And, the POS device indicates to PHY port '3' that it is ready to accept a block of packet data by placing its address on RADR and reasserting REN. On clock edge 10, PHY port '3' continues a packet transfer by asserting RVAL and placing the next byte of packet data on RDATA. 81 DS3181/DS3182/DS3183/DS3184 On clock edge 14, PHY port '3' places the last byte of the packet on RDATA, and asserts REOP to indicate that this is the last transfer of the packet. On clock edge 15, PHY port '3' deasserts RVAL and REOP ending the packet transfer process, as well as, deasserting RDXA to indicate that it does not have another block of packet data or an end of packet ready for transfer. On clock edge 16, the POS device indicates to PHY port '4' that it is ready to accept a block of packet data by placing its address on RADR and leaving REN asserted. On clock edge 17, PHY port '4' starts a packet transfer by leaving RVAL asserted, placing the first byte of the packet on RDATA, and asserting RSOX to indicate that this is the first transfer of the packet. On clock edge 18, PHY port '4' deasserts RSOX as it leaves RVAL asserted and continues to place additional bytes of the packet on RDATA. Figure 8-35. POS-PHY Level 2 Receive Multiple Packet Transfer from Different PHY Ports/Devices (direct status mode) RCLK RADR '1' '2' 1F '3' '4' RDXA[1] RDXA[2] RDXA[3] RDXA[4] REN RVAL RDATA P34 P35 P1 P2 ... P41 P42 P43 P19 P20 ... P63 P64 X X P1 P2 P3 P4 RSOX REOP RERR Transfer From PHY '1' 1 '2' 2 3 4 5 '3' 6 7 8 9 10 11 12 '4' 13 14 15 16 17 18 19 20 Figure 8-36 shows a multidevice transmit interface in packet transfer mode multiple packet transfer to different PHY ports. On clock edge 2, the POS device polls PHY port 'N'. On clock edge 3, PHY port 'N' indicates to the POS device that it can accept a block of packet data by asserting TPXA. On clock edge 4, the POS device selects PHY port 'N'. On clock edge 5, the POS device starts a packet transfer to PHY port 'N' by asserting TEN, placing the first byte of packet data on TDATA, and asserting TSOX to indicate the transfer of the first byte of the packet. On clock edge 6, the POS device deasserts TSOX as it continues to place additional bytes of the packet on TDATA. And, PHY port 'N' drives its TSPA output high. On clock edge 10, the POS device polls PHY port 'M'. On clock edge 11, the POS device asserts TEOP to indicate the transfer of the last byte of the packet to PHY port 'N' and PHY port 'M' indicates to the POS device that it can accept a block of packet data by asserting TPXA. On clock edge 12, the POS device deasserts TEN to end the packet transfer process to PHY port 'N' and selects PHY port 'M'. On clock edge 13, the POS device starts a packet transfer to PHY port 'M' by asserting TEN, placing the first byte of packet data on TDATA, and asserting TSOX to indicate the transfer of the first byte of the packet. And, PHY port 'N' tristates its TSPA output. On clock edge 14, the POS device deasserts TSOX as it continues to place additional bytes of the packet on TDATA. And, PHY port 'M' drives its TSPA output high. 82 DS3181/DS3182/DS3183/DS3184 Figure 8-36. POS-PHY Level 2 Transmit Multiple Packet Transfer to Different PHY Ports (polled status mode) TCLK TADR 1F TPXA M N 1F N 1F N O N 1F ... 1F O M L 1F M M 1F N M 1F O N 1F P O 1F L P TSPA TEN TDAT X X X X P1 P2 P3 ... P62 P63 P64 X P1 P2 P3 P4 P5 P6 P7 P8 TSOX TEOP TERR Transfer To PHY N 1 2 3 4 5 6 7 8 M 9 10 11 12 13 14 15 16 17 18 19 20 Figure 8-37 shows a multidevice receive interface in packet transfer mode multiple packet transfer. On clock edge 2, the POS device polls PHY port 'N'. On clock edge 3, PHY port 'N' indicates to the POS device that it has a block of packet data or an end of packet ready for transfer by asserting RPXA. On clock edge 4, the POS device selects PHY port 'N'. On clock edge 5, the POS device indicates to PHY port 'N' that it is ready to accept a block of packet data by placing its address on RADR and asserting REN. On clock edge 6, PHY port 'N' starts packet transfer by asserting RVAL, placing the first byte of the packet on RDATA, and asserting RSOX to indicate that this is the first transfer of the packet. On clock edge 7, PHY port 'N' deasserts RSOX as it leaves RVAL asserted and continues to place additional bytes of the packet on RDATA. On clock edge 14, PHY port 'N' places the last byte of the packet on RDATA, and asserts REOP to indicate that this is the last transfer of the packet. On clock edge 15, PHY port 'N' deasserts RVAL and REOP ending the packet transfer process. On clock edge 16, the POS device deasserts REN and selects PHY port 'P'. On clock edge 17, PHY port 'N' tri-states its RVAL, RDATA, RSOX, REOP, and RERR outputs and the POS device indicates to PHY port 'P' that it is ready to accept a block of packet data by placing its address on RADR and asserting REN. On clock edge 18, PHY port 'P' starts packet transfer by asserting RVAL, placing the first byte of the packet on RDATA, and asserting RSOX to indicate that this is the first transfer of the packet. On clock edge 19, PHY port 'P' deasserts RSOX as it leaves RVAL asserted and continues to place additional bytes of the packet on RDATA. While this example shows a different PHY port ('P') being selected for the next packet transfer, the timing is identical if the same PHY port ('N') is chosen for the next packet transfer. 83 DS3181/DS3182/DS3183/DS3184 Figure 8-37. POS-PHY Level 2 Receive Multiple Packet Transfer (polled status mode) RCLK RADR 1F RPXA M N 1F N 1F N O N 1F P 1F O ... P 1F M L 1F O M 1F P O 1F L P 1F M L REN RVAL RDAT P1 P2 P3 P4 ... P61 P62 P63 P64 X X P1 P2 P3 RSOX REOP RERR Transfer From PHY N 1 2 3 4 5 6 7 8 9 84 10 P 11 12 13 14 15 16 17 18 19 20 DS3181/DS3182/DS3183/DS3184 8.3.5.4 POS-PHY Level 3 Functional Timing Figure 8-38 shows a multiport transmit interface multiple packet transfer to different PHY ports. On clock edge 1, PHY port 'N' indicates to the POS device that it can accept a block of packet data by asserting TPXA. On clock edge 3, the POS device selects PHY port 'N' by placing its address on TDATA and asserting TSX while TEN is deasserted. On clock edge 4, the POS device starts a packet transfer to PHY port 'N' by deasserting TSX, asserting TEN, placing the first byte of packet data on TDATA, and asserting TSOX to indicate the transfer of the first byte of the packet. On clock edge 5, the POS device deasserts TSOX as it continues to place additional bytes of the packet on TDATA and PHY port 'N' asserts TSPA. On clock edge 11, the POS device polls PHY port 'L'. On clock edge 12, PHY port 'N' indicates that it cannot accept any more data transfers by deasserting TSPA. On clock edge 13, PHY port 'L' indicates to the POS device that it can accept a block of packet data by asserting TPXA. On clock edge 14, the POS device deasserts TEN to end the packet transfer process to PHY port 'N' and selects PHY port 'L' by placing its address on TDATA and asserting TSX while TEN is deasserted. On clock edge 15, the POS device starts a packet transfer to PHY port 'L' by asserting TEN, deasserting TSX, placing the first byte of packet data on TDATA, and asserting TSOX to indicate the transfer of the first byte of the packet. On clock edge 16, the POS device deasserts TSOX as it continues to place additional bytes of the packet on TDATA and PHY port 'L' asserts TSPA. Figure 8-38. POS-PHY Level 3 Transmit Multiple Packet Transfer In-Band Addressing TCLK TADR P L M N O TPXA N O P L M ... ... X X N P1 P2 ... M N O P L M N O P L M N O P P L M N O P L M N O P L M N P38 P39 P40 P41 P42 P43 P44 L P1 P2 P3 P4 P5 P6 TSPA TEN TSX TDAT TSOX TEOP TERR Transfer To PHY N 1 2 3 4 5 6 7 8 9 L 10 11 12 13 14 15 16 17 18 19 20 Figure 8-39 shows a multiport receive-interface multiple packet transfer from different ports. On clock edge 1, the POS device indicates to PHY port 'N' that it is ready to accept a block of packet data by asserting REN. On clock edge 3, the PHY device selects port 'N' for transfer by asserting RSX and placing its address on RDATA. On clock edge 4, PHY port 'N' starts packet transfer by deasserting RSX, asserting RVAL, placing the first byte of the packet on RDATA, and asserting RSOX to indicate that this is the first transfer of the packet. On clock edge 5, PHY port 'N' deasserts RSOX as it leaves RVAL asserted and continues to place additional bytes of the packet on RDATA. On clock edge 10, PHY port 'N' places the last byte of the packet on RDATA, and asserts REOP to indicate that this is the last transfer of the packet. On clock edge 11, the PHY device deasserts RVAL and REOP ending the packet transfer process from port 'N' and selects PHY port 'L' for transfer by asserting RSX and placing its address on RDATA. On clock edge 12, PHY port 'L' starts packet transfer by deasserting RSX, asserting RVAL, placing the first byte of the packet on RDATA, and asserting RSOX to indicate that this is the first transfer of the packet. On clock edge 13, PHY port 'L' deasserts RSOX as it leaves RVAL asserted and continues to place additional bytes of the packet on RDATA. 85 DS3181/DS3182/DS3183/DS3184 Figure 8-39. POS-PHY Level 3 Receive Multiple Packet Transfer In-Band Addressing RCLK REN RVAL RSX RDAT X N P1 P2 P3 ... P62 P63 P64 L P1 P2 P3 P4 P5 P6 P7 P8 P9 RSOX REOP RERR Transfer From PHY N 1 2 3 4 5 6 7 L 8 9 10 86 11 12 13 14 15 16 17 18 19 20 DS3181/DS3182/DS3183/DS3184 8.3.6 Microprocessor Interface Functional Timing Figure 8-40 and Figure 8-42 shows examples of a 16-bit databus and an 8-bit databus, respectively. In 16-bit mode, the A[0]/BSWAP signal controls whether or not to byte swap. In 8-bit mode, the A[0]/BSWAP signal is used as the LSB of the address bus (A[0]). The selection of databus size is determined by the WIDTH input signal. See also Section 10.1.1. Figure 8-40. 16-Bit Mode Write A[0]/BSWAP 0x2B0 A[10:1] D[15:0] 0x1234 CS WR RD RDY Z Z Note: Address 0x2B0 = 0x1234 Figure 8-41. 16-Bit Mode Read A[0]/BSWAP 0x2B0 A[10:1] D[15:0] 0x1234 CS WR RD RDY Z Z Note: Address 0x2B0 = 0x1234 87 DS3181/DS3182/DS3183/DS3184 Figure 8-42. 8-Bit Mode Write A[0]/BSWAP A[10:1] D[7:0] 0x2B0 0x2B0 0x34 0x12 CS WR RD RDY Z Z Z Z Note: Address 0x2B0 = 0x34 0x2B1 = 012 Figure 8-43. 8-Bit Mode Read A[0]/BSWAP 0x2B0 0x2B0 A[10:1] D[7:0] 0x12 0x34 CS WR RD RDY Z Z Z Z Note: Address 0x2B0 = 0x34 0x2B1 = 012 Figure 8-44 and Figure 8-45 are examples of databuses without and with byte swapping enabled, respectively. When the A[0]/BSWAP pin is set to 0, byte swapping is disabled, and when one, byte swapping is enabled. This pin should be static and not change while operating. Note: Address bit A[0] is not used in 16-bit mode. See also Section 10.1.2. 88 DS3181/DS3182/DS3183/DS3184 Figure 8-44. 16-Bit Mode without Byte Swap A[0]/BSWAP 0x2B0 A[10:1] D[15:0] 0x2B2 0x1234 0x5678 CS WR RD RDY Z Z Z Z Note: Address 0x2B0 = 0x1234 0x2B2 = 0x5678 Figure 8-45. 16-Bit Mode with Byte Swap A[0]/BSWAP 0x2B2 0x2B0 A[10:1] D[15:0] 0x3412 0x7856 CS WR RD RDY Z Z Z Z Note: Address 0x2B0 = 0x1234 0x2B2 = 0x5678 Clearing status latched registers on a read or write access is selectable via the GL.CR1.LSBCRE register bit. Clearing on read clears all bits in the register, while the clear on write clears only those bits which are written with a `1' when the user writes to the status latched register. To use the Clear on Read method, the user must only read the status latched register. All bits are set to zero after the read. Figure 8-46 shows a read of a status latched register and another read of the same register verifying the register has cleared. To use the Clear on Write method, the user must write the register with ones in the bit locations that he desires to clear. Figure 8-47 shows a read, a write, and then a subsequent read revealing the results of clearing of the bits that he wrote a `1'. See also Section 10.1.5 89 DS3181/DS3182/DS3183/DS3184 Figure 8-46. Clear Status Latched Register on Read A[0]/BSWAP 0x1C0 A[10:1] D[15:0] 0x1C0 0xFFFF 0x0000 CS WR RD RDY Z Z Z Z Figure 8-47. Clear Status Latched Register on Write A[0]/BSWAP 0x1C0 A[10:1] D[15:0] 0x1C0 0x1C0 0x5555 0xFFFF 0xAAAA CS WR RD RDY Z Z Z Z Z Z Figure 8-48 and Figure 8-49 show exaggerated views of the Ready Signal to describe the difference in access times to write or read to or from various memory locations on the DS318x device. Some registers will have a faster access time than others will and if needed, the user can implement the RDY signal to maximize efficiency of read and write accesses. Figure 8-48. RDY Signal Functional Timing Writes A[0]/BSWAP A[10:1] D[15:0] 0x2B0 0x3A4 0x1234 0x0078 CS WR RD RDY Z Z Z Z 90 DS3181/DS3182/DS3183/DS3184 Figure 8-49. RDY Signal Functional Timing Read A[0]/BSWAP 0x1C0 A[10:1] D[15:0] 0x3A4 0xFFFF 0xFFFF CS WR RD RDY Z Z Z Z See also Figure 18-7 and Figure 18-8. 8.3.7 JTAG Functional Timing See Section 13.5. 91 DS3181/DS3182/DS3183/DS3184 9 INITIALIZATION AND CONFIGURATION STEP 1: Check Device ID Code. Before any testing can be done, the device ID code, which is stored in GL.IDR, should be checked against device ID codes shown below to ensure that the correct device is being used. Current device ID codes are: o DS3181 rev 1.0: 0048h o DS3182 rev 1.0: 0049h o DS3183 rev 1.0: 004Ah o DS3184 rev 1.0: 004Bh STEP 2: Initialize the Device. Before configuring for operation, make sure the device is in a known condition with all registers set to their default value by initiating a Global Reset. (See Section 10.3) A Global Reset can be initiated via the RST pin or by the Global Reset bit (GL.CR1.RST). A Port Reset is not necessary since the global reset includes a reset of all ports to their default values. STEP 3: Clear the Reset. It is necessary to clear the RST bit to begin normal operation. After clearing the RST bit, the device is configured for default mode. Default mode: System Interface: UTOPIA Level 2, 8-bit databus Framer: C-bit DS3 LIU: Disabled STEP 4: Clear the Data Path Resets and the Port Power-Down bit. The default value of the Data Path Resets is one, which keeps the internal logic in the reset status. The user needs to clear the following bits: GL.CR1.RSTDP = 0 PORT.CR1.RSTDP = 0 PORT.CR1.PD = 0 STEP 5: Configure the CLAD. If using the LIU, configure the CLAD (the Clock Rate Adapter, which supplies the clock to the Receive LIU) via the CLAD bits in the GL.CR2 register. Note: The user must supply a DS3, E3, or STS-1 clock to the CLKA pin. STEP 6: Select the clock source for the transmitter. Loop Time (use the receive clock): Set PORT.CR3.LOOPT = 1 CLAD Source: Set PORT.CR3.CLADC = 0 TCLKI Source: Set PORT.CR3.CLADC = 1 If using the CLAD, properly configure the CLAD by setting the CLAD bits in GL.CR2. STEP 7: Configure the Framing Mode and the Line Mode. PORT.CR2.LM[2:0] = 011 -LIU on, JA in RX side-or another setting. See Table 10-33. PORT.CR2.FM[5:0] set to the correct framing mode. See Table 10-32. STEP 8: Disable Payload AIS (downstream AIS) and Line AIS PORT.CR1.PAIS[2:0] = 111 PORT.CR1.LAIS[1:0] = 11 STEP 9: Initialize and configure the FIFOs. Reset the Transmit and Receive FIFO. FF.TCR.TFRST = 1. 92 DS3181/DS3182/DS3183/DS3184 FF.RCR.RFRST = 1. Clear the FIFO Reset bits. FF.TCR.TFRST = 0. FF.RCR.RFRST = 0. Set the FIFO Transmit Level Control Register and the FIFO Transmit Port Address Control Register. Set the FIFO Receive Level Control Register and the FIFO Receive Port Address Control Register. The Port Address needs to be configured to match the master controller address for each port. STEP 10: Configure the System Bus Configure for bus size and for interface type. See Table 9-1. Optionally, set the System Interface Transmit Control Register, System Interface Receive Control Register #1 and #2 to fine tune for the specific application. (User may leave registers at default value.) STEP 11: Configure the Cell or Packet Processor For cell mode, the default is to send the cell across the system interface without the HEC. Also, default mode scrambles the cell data to the line. To attach the HEC to the cell, set SI.TCR.THECT = 1 and SI.RCR.RHECT = 1. STEP 12: Enable each port (for non-LIU modes) PORT.CR2.TLEN = 1 Table 9-1. Configuration of Global Register Settings Note: This table assumes a DS3 clock input on the CLKA pin. GL.CR1 0x002 GL.CR20x00 4 GL.GIOCR 0x00A UTOPIA L2 0000 XX00 0000 0000 0x0204 0x0000 UTOPIA L3 0000 XX01 0000 0000 0x0204 0x0000 POS-PHY L2 0000 XX10 0000 0000 0x0204 0x0000 POS-PHY L3 or SPI-3 0000 XX11 0000 0000 0x0204 0x0000 8-Bit System Bus 0000 00XX 0000 0000 0x0204 0x0000 16-Bit System Bus 0000 01XX 0000 0000 0x0204 0x0000 32-Bit System Bus 0000 10XX 0000 0000 0x0204 0x0000 MODE Table 9-2. Configuration of Port Register Settings Note: The Line Mode has been configured with the LIU enabled and the JA in the receive path (LM[2:0] = 011) for all modes except OHM mode. Only Port 1 registers have been displayed. PORT.CR1 0x040 PORT.CR2 0x042 PORT.CR3 0x044 PORT.CR4 0x046 DS3 C-Bit 0x7C00 0000 0011 0000 000X 0x0000 0x0000 DS3 C-Bit PLCP 0x7C00 0000 0011 0000 010X 0x0000 0x0000 DS3 M23 0x7C00 0000 0011 0000 100X 0x0000 0x0000 DS3 M23 PLCP 0x7C00 0000 0011 0000 110X 0x0000 0x0000 E3.751 0x7C00 0000 0011 0001 000X 0x0000 0x0000 E3.751 PLCP 0x7C00 0000 0011 0001 010X 0x0000 0x0000 E3.823 0x7C00 0000 0011 0001 100X 0x0000 0x0000 OHM Mode (DS3/E3/Clear Channel) 0x7C00 1100 0XXX 00XX XXXX 0x0000 0x0000 MODE 93 DS3181/DS3182/DS3183/DS3184 Considerations Select the HDLC Controller connection. The default setting connects it to the DS3/E3 Framers. Setting PORT.CR1.HDSEL = 1 connects the HDLC Controller to the PLCP framers. In POS-PHY mode, to select cell processing rather than packet processing, set PORT.CR2.PMCPE = 1. For best performance of the CLAD to meet jitter requirements across the temperature range, especially @ -40 C, the following test registers should be set after reset: Address 0x20B = 0x11 Address 0x20F = 0x11 9.1 Monitoring and Debugging To determine if the device is receiving a good signal and that the chip is correctly configured for its environment, check the following status registers. Receive Loss of Lock - PORT.SR.RLOL - The clock recovery circuit of the LIU was unable to recover the clock from the incoming signal. This may indicate that the LIU's master clock does not match the frequency of the incoming signal. Verify that the CLAD is configured to match the clock input on the CLKA, CLKB, and CLKC pins (DS3, E3, STS-1). See Table 10-11. Loss of Signal - LINE.RSR.LOS - This indicates that the LIU is unable to recover the clock and data because there is no signal on the line, or that the signal is attenuated beyond recovery. Loss of Frame - T3.RSR1.LOF (or E3751.RSR1 or E3832.RSR1) - This indicates that the framer was unable to synchronize to the incoming data. Verify that the FM bits have been correctly configured for the correct mode of traffic (DS3, E3 G.751, E3 G.832) Other helpful techniques diagnose a problem include using Line Loopback and Diagnostic Loopback. These features help to isolate and identify the source of the problem. Line Loopback will loop the receive input to the transmit output, eliminating the transmit side input from the equation. Diagnostic Loopback will loop the transmit output before the LIU to the receive framer, eliminating the analog Receive LIU and the receive side analog circuitry. One other potential problem is the Line Encoding/Decoding. The device needs to be configured in the same mode as the far end piece of equipment. If the far end piece of equipment is transmitting and receiving HDB3/B3ZS encoded data, the DS318x also must be configured to do the same. This is controlled by the LINE.TCR.TZSD and the LINE.RCR.RZSD bits. 9.1.1 Cell/Packet FIFO Check the status registers of the FIFO block. Common indicators to check would be the Transmit Underflow, Transmit Overflow, and Receive Overflow status bits. These status bits are located in the FIFO.TSRL Register and the FIFO.RSRL Register. A Transmit Underflow indicates that the transmit cell processor or packet processor has attempted a read while the FIFO was empty. A Transmit Overflow indicates that either a start of cell or a start of packet or a short packet was received when the FIFO was full. Additionally, if additional packet data is received when the FIFO is already full, it will result in an abort status for the current packet and the Transmit Overflow being declared. A Receive Overflow occurs when cell data is received while the FIFO is full. In a packet system, the overflow will be declared when a start of packet or a short packet is received or packet data is received when the FIFO is full resulting in an abort status for the current packet and the Receive Overflow being declared. 9.1.2 Cell Processor Monitoring the Loss of Cell Delineation in the Cell Processor is recommended to insure proper operation. The LCD status bit is located in the CP.RSR Register and indicates when an Out of Cell Delineation persists for a programmed number of cells (set in the CP.RLTC Register). 94 DS3181/DS3182/DS3183/DS3184 9.1.3 Packet Processor Monitoring the number of errored packets in the Packet Processor is recommended for proper operation. The REPC status bit is located in the PP.RSR Register and indicates when the errored packet count is not zero. An errored packet is detected when an errored FCS is detected. To determine how many errored packets have been received, the FCS Errored Packet Count Registers must first be updated via the PMU signal. 95 DS3181/DS3182/DS3183/DS3184 10 FUNCTIONAL DESCRIPTION 10.1 Processor Bus Interface 10.1.1 8/16-Bit Bus Widths The external processor bus can be sized for 8 or 16 bits using the WIDTH pin. When in 8-bit mode (WIDTH=0), the address is composed of all the address bits including A[0], the lower 8 data lines D[7:0] are used and the upper 8 data lines D[15:8] are not used and never driven during a read cycle. When in 16-bit mode (WIDTH=1), the address bus does not include A[0] (the LSB of the address bus is not routed to the chip) and all 16 data lines D[15:0] are used. See Figure 8-40 and Figure 8-42 for functional timing diagrams. 10.1.2 Ready Signal (RDY) The RDY signal allows the microprocessor to use the minimum bus cycle period for maximum efficiency. When this signal goes low, the RD or WR cycle can be terminated. See Figure 8-48 for functional timing diagrams. NOTE: The RDY signal will not go active if the user attempts to read or write unused ports or unused registers not assigned to any design blocks. The RDY signal will go active if the user writes or reads reserved registers or unused registers within design blocks. 10.1.3 Byte Swap Modes The processor interface can operate in byte swap mode when the data bus is configured for 16-bit operation. The A[0]/BSWAP pin is used to determine whether byte swapping is enabled. This pin should be static and not change while operating. When the A[0]/BSWAP pin is low the upper register bits REG[15:8] are mapped to the upper external data bus lines D[15:8], and the lower register bits REG[7:0] are mapped to the lower external data bus lines D[7:0]. When the A[0]/BSWAP pin is high the upper register bits REG[15:8] are mapped to the lower external data bus lines D[7:0], and the lower register bits REG[7:0] are mapped to the upper external data bus lines D[15:8]. See Figure 8-44 and Figure 8-45 for functional timing diagrams. 10.1.4 Read-Write/Data Strobe Modes The processor interface can operate in either read-write strobe mode or data strobe mode. When MODE=0 the read-write strobe mode is enabled and a negative pulse on RD performs a read cycle, and a negative pulse on WR performs a write cycle. When MODE=1 the data strobe mode is enabled and a negative pulse on DS when R/W is high performs a read cycle, and a negative pulse on DS when R/W is low performs a write cycle. The read-write strobe mode is commonly called the "Intel" mode, and the data strobe mode is commonly called the "Motorola" mode. 10.1.5 Clear on Read/Clear on Write Modes The latched status register bits can be programmed to clear on a read access or clear on a write access. The global control register bit GL.CR1.LSBCRE controls the mode that all of the latched registers are cleared. When LSBCRE=0, the latched register bits will be cleared when the register is written to and the write data has the register bits to clear set. When LSBCRE=1, the latched register bits that are set will be cleared when the register is read. The clear on write mode expects the user to use the following protocol: 1. Read the latched status register 2. Write to the registers with the bits set that need to be cleared. This protocol is useful when multiple uncoordinated software tasks access the same latched register. Each task should only clear the bits with which it is concerned; the other tasks will clear the bits with which they are concerned. The clear on read mode is simpler since the bits that were read as being set will be cleared automatically. This method will work well in a software system where multiple tasks do not read the same latched status register. The 96 DS3181/DS3182/DS3183/DS3184 latched status register bits in clear on read mode are carefully designed not to miss events that occur while a register is being read when the latched bit has not already been set. See Figure 8-46 and Figure 8-47. 10.1.6 Global Write Method All of the ports can be written to simultaneously using the global write method. This method is enabled by setting the GL.CR1.GWM bit. When the global write method is enabled, a write to a register on any valid port will write to the same register on all valid ports. A valid port is a port that is available in a particular packaged part. For example, port four would not be valid in a DS3183 device. After reset, the global write method is not enabled. When the GWM bit is set, read data from the port registers is not valid and read data from the global and test registers is valid. The data value read back from a port register should be ignored. 10.1.7 Interrupt and Pin Modes The interrupt (INT) pin is configurable to drive high or float when not active. The GL.CR1.INTM bit controls the pin configuration, when it is set the INT pin will drive high when not active. After reset, the INT pin will be in high impedance mode until an interrupt source is active and enabled to drive the interrupt pin. 10.1.8 Interrupt Structure The interrupt structure is designed to efficiently guide the user to the source of an enabled interrupt source. The status bits in the global status (GL.SR) and global status latched register (GL.SRL) are read to determine if the interrupt source is a global event like the UTOPIA/POS-PHY interface, global performance monitor update or whether it came from one of the ports. If the interrupt event came from one of the ports then the port status register (PORT.SR) and port status register latched (PORT.SRL) can be read to determine if the interrupt source is a common port event like the performance monitor update or LIU or whether it came from one of the DS3/E3 Framers, PLCP Framer, ATM/PKT, BERT, HDLC, FEAC or Trail Trace status registers. If the interrupt came from one of the DS3/E3 Framers, PLCP Framer, ATM/PKT, BERT, HDLC, FEAC or Trail Trace status registers, then one of those registers will need to be read to determine the event that caused the interrupt. The source of an interrupt can be determined by reading three status registers: global, port and block status registers. When a mode is not enabled, then interrupts from that source will not occur. For example, if PLCP framing is not enabled then the potential interrupts from the latched status register in the PLCP block cannot occur. Similarly, if E3 framing mode is enabled, an interrupt source that is defined in DS3 framing, but not in E3 framing, cannot create a new interrupt. Note that when modes are changed, the latched status bits of the new mode, as well as any other mode, may get set. If the data path reset is set during or after the mode change, the latched status bits will be automatically cleared. If the data path reset is not used to clear the latched status bits, then the registers must be cleared by reading or writing to them based on the register clear method selected. 97 DS3181/DS3182/DS3183/DS3184 Figure 10-1. Interrupt Structure SRL bit SRIE bit SRL bit PORT.ISR bit SRIE bit SRL bit GL.ISR.PISRn SRIE bit GL.ISRIE. PISRIEn BLOCK LATCHED STATUS and INTERRUPT ENABLE REGISTERS GLOBAL INTERRUPT STATUS REGISTER and INTERRUPT ENABLE REGISTER PORT INTERRUPT STATUS REGISTER PORT INTERRUPTS INT TRANSMIT SYSTEM INTERFACE INTERRUPTS GLOBAL INTERRUPTS Figure 10-1 not only tells the user how to determine which event caused the interrupt, it also tells the user how to enable a particular interrupt. Each block has a Status Register Interrupt Enable register that must be set in order to enable an interrupt. The next step is to unmask the interrupt at the port level, on a per-port basis. This is controlled in the Global Interrupt Status Register Interrupt Enable register (GL.ISRIE). Now the device is ready to drive the INT pin low when a particular status bit gets set. For example, in order to enable DS3 Out of Frame interrupts on Port 2, the following registers would need to be written: Register bit Address Value Written Note T3.RSRIE1.OOFIE 0x32C 0x0002 Unmask OOF interrupt on Port 2 GL.ISRIE.PISRIE2 0x012 0x0020 Unmask Port 2 interrupts The following status registers bits will be set upon reception of OOF on Port 2: Register bit Address Value Read Note T3.RSRL1.OOFL 0x328 0x0002 DS3 Out of Frame on Port 2 PORT.ISR.FMSR 0x250 0x0001 Framer Block Interrupt Active, Port 2 GL.ISR.PISR2 0x010 0x0020 Port 2 Interrupt Active 98 DS3181/DS3182/DS3183/DS3184 10.2 Clocks 10.2.1 Line Clock Modes The system loopback (SLB) function does not affect the line clocks in any way. 10.2.1.1 Loop Timing Enabled When loop timing is enabled (PORT.CR3.LOOPT), the transmit clock source is the same as the receive clock source. The TCLKIn pins are not used as a clock source. Because loop timing is enabled, the loopback functions (LLB, PLB and DLB) do not cause the clock sources to switch when they are activated. The transmit and receive signal pins can be timed to a single clock reference without concern about having the clock source change during loopbacks. 10.2.1.1.1 LIU Enabled, Loop Timing Enabled In this mode, the receive LIU sources the clock for both the receive and transmit logic. The RCLKOn, TCLKOn and TLCLKn clock output pins will be the same. The transmit or receive line, payload and fractional signal pins can be timed to any of these clock. The use of the RCLKOn pin as the timing source is suggested. If RCLKOn is used as the timing source, be sure to set PORT.CR3.RFTS = 0 for output timing. 10.2.1.1.2 LIU Disabled, Loop Timing Enabled In this mode, the RLCLKn pins are the source of the clock for both the receive and transmit logic. The RCLKOn, TCLKOn and TLCLKn clock output pins will both be the same as the RLCLKn clock. The transmit or receive line, payload and fractional signals can be timed to any of these clock pins. The use of the RLCLKn pin as the timing source is suggested. If RLCLKn is used as the timing source, be sure to set PORT.CR3.RFTS = 1 for input timing. 10.2.1.2 Loop Timing Disabled When loop timing is disabled, the transmit clock source can be different than the receive clock source. The loopback functions, LLB, PLB and DLB, will cause the clock sources to switch when they are activated. Care must be taken when selecting the clock reference for the transmit and receive signals. The most versatile clocking option has the receive line interface signals timed to RLCLKn, the transmit line interface signals timed to TLCLKn, the receive framer and fractional signals timed to RCLKOn, and the transmit framer and fractional signals timed to TCLKOn. This clocking arrangement works in all modes. When LLB is enabled, the clock on the TLCLKn pins will switch to the clock from the RLCLKn pins or RX LIU. It is recommended that the transmit line interface signals be timed to the TLCLKn pins. If TLCLKn is used as the timing source, be sure to set PORT.CR3.TLTS = 0 for output timing. When PLB is enabled, the TCLKIn pin will not be used and the internal transmit clock is switched to the internal receive clock. The clock on the TCLKOn pins will switch to the clock from the RLCLKn pins or RX LIU. The framer or fractional input signals will be ignored while PLB is enabled. It is recommended that the transmit line interface signals be timed to the TCLKOn pins. When DLB is enabled, the internal receive clock is switched to the internal transmit clock which is sourced from the TCLKIn pins or one of the CLAD clocks, and the clock on the RLCLKn pins or from the RX LIU will not be used. The clock on the RCLKOn pins will switch to the clock on the TCLKIn pins or one of the CLAD clocks. The receive line signals from the RX LIU or line interface pins will be ignored. It is recommended that the receive framer and fractional pins be timed to the RCLKOn pins. If TCLKOn is used as the timing source, be sure to set PORT.CR3.TFTS = 0 for output timing. When both DLB and LLB are enabled, the TLCLKn clock pins are connected to either the RX LIU recovered clock or the RLCLKn clock pins, and the RCLKOn clock pins will be connected to the TCLKIn clock pins or one of the CLAD clocks. It is recommended that the transmit line signals be timed to the TLCLKn pins, the receive line interface signals be timed to the RLCLKn pins, the receive framer and fractional signals be timed to the RCLKOn pins, and the transmit framer and fractional signals be timed to the TCLKOn pins. 10.2.1.2.1 LIU Enabled - CLAD Timing Disabled - no LB In this mode, the receive LIU sources the clock for the receive logic and the TCLKIn pins source the clock for the transmit logic. 99 DS3181/DS3182/DS3183/DS3184 10.2.1.2.2 LIU Enabled - CLAD Timing Enabled - no LB In this mode, the receive LIU sources the clock for the receive logic and one of the CLAD clocks sources the clock for the transmit logic. 10.2.1.2.3 LIU Disabled - CLAD Timing Disabled - no LB In this mode, the RLCLKn pins source the clock for the receive logic and the TCLKIn pins source the clock for the transmit logic. 10.2.1.2.4 LIU Disabled - CLAD Timing Enabled - no LB In this mode, the RLCLKn pins source the clock for the receive logic and one of the CLAD clocks sources the clock for the transmit logic. 10.2.2 Sources of Clock Output Pin Signals The clock output pins can be sourced from many clock sources. The clock sources are the transmit input clocks pins (TCLKIn), the receive clock input pins (RLCLKn), the recovered clock in the receive LIUs, and the clock signals in the clock rate adapter circuit (CLAD). The default clock source for the receive logic is the RLCLKn pin if the LIU is disabled; otherwise the default clock is sourced from the RX LIU clock when the RX LIU is enabled. The default clock source for the transmit logic is the CLAD clocks. The LIU is enabled based on the line mode bits (LM[2:0]) (See Table 10-33). The bits LM[2:0], LBM[2:0], LOOPT and CLADC are located in the port configuration registers. LIUEN is not a register bit; it is a variable based on the line mode bits. LIUEN is also zero (LIU disabled) when an "-OHM" mode is selected. Table 10-1 decodes the LM bits for LIUEN selection. Table 10-1. LIU Enable Table LM[2:0] LIUEN 000 001 010 011 1XX 0 1 1 1 0 LIU STATUS Disabled Enabled Enabled Enabled Disabled Table 10-2 identifies the framer clock source and the line clock source depending on the mode that the device is configured. Putting the device in loopback will typically mux in a different clock than the normal clock source. Table 10-2. All Possible Clock Sources Based on Mode and Loopback RX FRAMER CLOCK SOURCE RLCLKn or RXLIU RLCLKn or RXLIU RLCLKn or RXLIU RLCLKn or RXLIU MODE LOOPBACK Loop Timed Any Normal None Normal LLB Normal PLB Normal DLB Same as TX Normal LLB and DLB Same as TX TX FRAMER CLOCK SOURCE TX LINE CLOCK SOURCE Same as RX Same as RX TCLKIn or CLAD TCLKIn or CLAD Same as RX TCLKIn or CLAD TCLKIn or CLAD 100 Same as TX Same as RX Same as RX Same as TX RLCLKn or RXLIUn DS3181/DS3182/DS3183/DS3184 Table 10-3 identifies the source of the output signal TLCLKn based on certain variables and register bits. Table 10-3. Source Selection of TLCLK Clock Signal SIGNAL TLCLKn LOOPT PORT.CR3 LBM[2:0] (PORT.CR4) LLB OR PLB? LIUEN CLADC (PORT.CR3) SOURCE 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 XXX XXX 010 110 010 110 011 011 000 001 100 10X 111 000 001 100 10X 111 NA NA LLB LLB LLB LLB PLB PLB NO NO NO NO NO NO NO NO NO NO 1 0 1 1 0 0 1 0 X X X X X X X X X X X X X X X X X X 0 0 0 0 0 1 1 1 1 1 RX LIU RLCLKn RX LIU RX LIU RLCLKn RLCLKn RX LIU RLCLKn CLAD CLAD CLAD CLAD CLAD TCLKIn TCLKIn TCLKIn TCLKIn TCLKIn Figure 10-2 shows the source of the TCLKOn signals. Figure 10-2. Internal TX Clock PORT.CR3. CLADC CLAD PAYLOAD LOOPBACK 0 0 TCLKI TCLKO 1 1 RCLKO Table 10-4 identifies the source of the output signal TCLKOn based on certain variables and register bits. 101 DS3181/DS3182/DS3183/DS3184 Table 10-4. Source Selection of TCLKOn (internal TX clock) SIGNAL LOOPT PORT.CR3 LBM[2:0] (PORT.CR4) LIUEN CLADC (PORT.CR3) SOURCE 1 1 0 0 0 0 XXX XXX PLB (011) PLB (011) PLB disabled PLB disabled 1 0 1 0 X X X X X X 0 1 RX LIU RLCLKn RX LIU RLCLKn CLAD TCLKIn TCLKOn Figure 10-3 shows the source of the RCLKOn signals. Figure 10-3. Internal RX Clock LIUEN RLCLK DIAGNOSTIC LOOPBACK 0 0 Rx LIU CLOCK RCLKO 1 1 TCLKO Table 10-5 identifies the source of the output signal RCLKOn based on certain variables and register bits. Table 10-5. Source Selection of RCLKO Clock Signal (internal RX clock) SIGNAL RCLKOn LOOPT PORT.CR3 LBM[2:0] (PORT.CR4) 1 1 0 XXX XXX DLB disabled DLB disabled and ALB disabled DLB (1XX) DLB (1XX) or ALB (001) DLB (1XX) 0 0 0 0 LIUEN CLADC (PORT.CR3) SOURCE 1 0 1 X X X RX LIU RLCLKn RX LIU 0 X RLCLKn X 0 CLAD 0 1 TCLKIn 1 1 TCLKIn 102 DS3181/DS3182/DS3183/DS3184 10.2.3 Line IO Pin Timing Source Selection The line IO pins can use any input clock pin (RLCLKn or TCLKIn) or output clock pin (TLCLKn, RCLKOn, or TCLKOn) for its clock pin and meet the AC timing specifications as long as the clock signal is valid for the mode the part is in. The clock select bit for the transmit line IO signal group PORT.CR3.TLTS selects the correct input or output clock timing. 10.2.3.1 Transmit Line Interface Pins Timing Source Selection (TPOSn/TDATn, TNEGn/TOHMOn) The transmit line interface signal pin group has the same functional timing clock source as the TLCLKn pin described in Table 10-3. Other clock pins can be used for the external timing. The TLCLKn transmit line clock output pin is always a valid output clock for external logic to use for these signals when PORT.CR3.TLTS=0. The transmit line timing select bit (TLTS) is used to select input or output clock pin timing. When TLTS=0, output clock timing is selected. When TLTS=1, input clock timing is selected. If TLTS is set for input clock timing and an output clock pin is used, or if TLTS is set for output clock timing and an input clock pin is used, then the setup, hold and delay timings, as specified in Table 18-1, will not be valid. There are some combinations of TLTS=1 and other modes in which there is no input clock pin available for external timing since the clock source is derived internally from the RX LIU or the CLAD. 0 0 0 0 TLTS 0 XXX XXX XXX DLB (100) LLB (010) or PLB (011) DLB&LLB (110) not DLB (100), not LLB (010), not PLB (011) and not LLB&DLB (110) not LLB (010) and not PLB (011) and not LLB&DLB (110) not LLB (010) and not PLB (011) and not LLB&DLB (110) LLB (010) or PLB (011) or DLB&LLB (110) LLB (010) or PLB (011) or DLB&LLB (110) CLADC 1 1 1 0 0 0 LBM[2:0] LIUEN LOOPT Table 10-6. Transmit Line Interface Signal Pin Valid Timing Source Select X 0 1 X X X X X X X X X 0 1 1 0 0 0 TLCLKn, TCLKOn, RCLKOn RLCLKn No valid timing to any input clock pin TLCLKn, TCLKOn, RCLKOn TLCLKn, RCLKOn TLCLKn X X 0 TLCLKn, TCLKOn (default) X 0 1 No valid timing to any input clock pin X 1 1 TCLKIn 0 X 1 RLCLKn 1 X 1 No valid timing to any input clock pin VALID TIMING TO THESE CLOCK PINS 10.2.3.2 Transmit Framer and Fractional Pin Timing Source Selection (TFOHn/TSERn, TFOHENIn/TPDENIn, TOHMIn/TSOFIn, TSOFOn/TDENn/TFOHENOn, TPDATn, TPDENOn) The transmit framer and fractional signal pin group has the same functional timing clock source as the TCLKO pin described in Table 10-4. Other clock pins can be used for the external timing. The TCLKO transmit clock output pin is always a valid output clock for external logic to use for these signals when TFTS=0. The transmit framer and fractional timing select bit (TFTS) is used to select input or output clock pin timing. When TFTS=0, output clock timing is selected. When TFTS=1, input clock timing is selected. If TFTS is set for input clock timing and an output clock pin is used, or If TFTS is set for output clock timing and an input clock pin is used, then the setup, hold and delay timings, as specified in Table 18-1, will not be valid. There are some combinations of TFTS=1 and other modes in which there is no input clock pin available for external timing since the clock source is derived internally from the RX LIU or the CLAD. 103 DS3181/DS3182/DS3183/DS3184 Table 10-7. Transmit Framer Pin Signal Timing Source Select LOOPT LBM[2:0] LIUEN CLADC TFTS 1 1 XXX XXX X 0 X X 0 1 1 XXX 1 X 1 VALID TIMING TO THESE CLOCK PINS TCLKOn, TLCLKn, RCLKOn RLCLKn No valid timing to any input clock pin 0 X 0 TCLKOn, TLCLKn, RCLKOn 0 0 0 0 PLB (011) or DLB (100) or ALB (001) PLB (011) or DLB (100) DLB&LLB (110) LLB (010) not LLB, DLB or PLB (00X) 1 X X X X X X X 0 0 0 0 0 not PLB (011) X 0 1 0 0 not PLB (011) PLB (011) X 0 1 X 1 1 0 PLB (011) 1 X 1 TCLKOn, TLCLKn, RCLKOn TCLKOn, RCLKOn TCLKOn TCLKOn, TLCLKn No valid timing to any input clock pin TCLKIn RLCLKn No valid timing to any input clock pin 0 10.2.3.3 Receive Line Interface Pin Timing Source Selection (RPOSn/RDATn, RNEGn/RLCVn/ROHMIn) The receive line interface signal pin group must clocked in with the RLCLK clock input pin. When the LIU is enabled, the receive line interface pins are not used so there is no valid clock reference. Table 10-8. Receive Line Interface Pin Signal Timing Source Select LOOPT LBM[2:0] LIUEN CLADC X X XXX XXX 0 1 X X VALID TIMING TO THESE CLOCK PINS RLCLKn No valid timing to any clock pin 10.2.3.4 Receiver Framer and Fractional Pin Timing Source Selection (RSERn, RSOFOn/RDENn/RFOHENOn, RFOHENIn/RPDENIn, RPDATn) The receive framer and fractional signal pin group has the same functional timing clock source as the RCLKOn pin described in Table 10-5. Other clock pins can be used for the external timing. The RCLKOn receive clock output pin is always a valid output clock for external logic to use for these signals when PORT.CR3.RFTS=0. The receive framer and fractional timing select bit (RFTS) is used to select input or output clock pin timing. When RFTS=0, output clock timing is selected. When RFTS=1, input clock timing is selected. If RFTS is set for input clock timing and an output clock pin is used, or If RFTS is set for output clock timing and an input clock pin is used, then the setup, hold and delay timings, as specified in Table 18-1, will not be valid. There are some combinations of RFTS=1 and other modes in which there is no input clock pin available for external timing since the clock source is derived internally from the RX LIU or the CLAD. 104 DS3181/DS3182/DS3183/DS3184 Table 10-9. Receive Framer Pin Signal Timing Source Select LOOPT LBM[2:0] LIUEN CLADC RFTS 1 1 XXX XXX X 0 X X 0 1 1 XXX 1 X 1 VALID TIMING TO THESE CLOCK PINS RCLKOn, TLCLKn, TCLKOn RLCLKn No valid timing to any input clock pin 0 X 0 RCLKOn, TLCLKn, TCLKOn 0 0 0 0 PLB (011) or DLB (100) or ALB (001) PLB (011) or DLB (100) DLB&LLB (110) LLB (010) not LLB, DLB or PLB (00X) 1 X X X X X X X 0 0 0 0 0 DLB (100) or LLB&DLB(110) X 0 1 0 DLB (100) or LLB&DLB(110) not DLB (100) and not LLB&DLB(110) not DLB (100) and not LLB&DLB(110) X 1 1 RCLKOn, TLCLKn, TCLKOn RCLKOn, TCLKOn RCLKOn, TLCLKn RCLKOn No valid timing to any input clock pin TCLKIn 0 X 1 RLCLKn 1 X 1 No valid timing to any input clock pin 0 0 0 10.2.4 Clock Structures On Signal IO Pins The signals on the input pins (RFOHENIn, TOHMIn/TSOFIn, TFOHn/TSERn, TFOHENIn) can be used with any of the clock pins for setup/hold timing on clock input and output pins. There will be a flop at each input whose clock is connected to the signal from the input or output clock source pins with as little delay as possible from the signal on the clock IO pins. This means using the input clock signal before the delays of the internal clock tree to clock the input signals, and using the output clock signals used to drive the output clock pins to clock the input signals. The signals on the output pins (TPOSn/TDATn, TNEGn/TOHMOn, TSOFOn/TDENn/TFOHENOn, RSERn, RSOFOn/RDENn/RFOHENOn) can be used with any of the clock sources for delay timing. There will be a flop at each output whose clock is connected to the signal from the input or output clock source pins with as little delay as possible from the signal on the clock IO pins. This means using the input clock signal before the delays of the internal clock tree to clock the input signals, and using the output clock signals to drive the output clock pins to clock the input signals. 105 DS3181/DS3182/DS3183/DS3184 Figure 10-4. Example IO Pin Clock Muxing TSER D PIN INVERT SET D Q Q DELAY 0 1 TFTS CLR Q CLR INTERNAL SIGNAL D SET CLR CLOCK TREE TCLKI SET INTERNAL SIGNAL Q D Q Q SET DELAY 0 CLR TDEN Q Q PIN INVERT 1 TFTS TCLKO PIN INVERT PIN INVERT INTERNAL SIGNAL RLCLK PIN INVERT D SET CLR CLOCK TREE D Q Q SET DELAY 0 CLR TPOS Q Q PIN INVERT 1 TLTS TLCLK RX LIU CLK PIN INVERT CLAD CLOCKS DS3 CLK E3 CLK STS-1 CLK INTERNAL SIGNAL D CLOCK TREE SET CLR D Q Q SET DELAY 0 CLR RSER Q Q PIN INVERT 1 RFTS RCLKO PIN INVERT 10.2.5 Gapped Clocks The transmit and receive output clocks can be gapped in certain configurations. See Table 10-24 and Table 10-31 for the configuration settings. The gapped clocks are active during DS3 or E3 framed payload bits or DS3 or E3 fractional overhead bits depending on which mode the device is configured for. In the internal DS3 or E3 fractional modes, the transmit gapped clock is created by the logical OR of the TCLKOn and TFOHENOn signals creating a positive or negative clock edge for each fractional overhead bit, the receive gapped clock is created by the logical OR of the RCLKOn and RFOHENOn signals. In the internal DS3 or E3 nonfractional modes, the transmit gapped clock is created by the logical OR of the TCLKOn and TDENn signals creating a positive or negative clock edge for each payload bit, the receive gapped clock is created by the logical OR of the RCLKOn and RDENn signals. When the output clock is disabled, the gapped output signal is high during clock periods if the pin is not inverted; otherwise it will be low. The gapped clocks are very useful when the data being clocked does not need to be aligned with any frame structure. The data is simply clocked one bit at a time as a continuous data stream. 106 DS3181/DS3182/DS3183/DS3184 10.3 Reset and Power-Down The device can be reset at a global level via the GL.CR1.RST bit or the RST pin and at the port level via the PORT.CR1.RST bit and each port can be explicitly powered down via the PORT.CR1.PD bit. The JTAG logic is reset using the JTRST pin. The external RST pin and the global reset bit in the global configuration register (GL.CR1.RST) are combined to create an internal global reset signal. The global reset signal resets all the status and control registers on the chip, except the GL.CR1.RST bit, to their default values and resets all the other flops in the system bus interface, global logic and ports to their reset values. The processor bus output signals are also forced to be HIZ when the RST pin is active (low). The global reset bit (GL.CR1.RST) stays set after a one is written to it, but is reset to zero when the external RST pin is active or when a zero is written to it. At the port level, the global reset signal combines with the port reset bit in the port control register (PORT.CR1.RST) to create a port reset signal. The port reset signal resets all the status and control registers on the port to their default values and resets all the other flops, except PORT.CR1.RST, to their reset values. The port reset bit (PORT.CR1.RST) stays set after a one is written to it, but is reset to zero when the global reset signal is active or when a zero is written to it. The data path reset function is a little different from the "general" reset function. The data path reset signal does not reset the control register bits, but it does reset all of the status registers, counters and flops, the "general" reset signal resets everything including the control register bits, excluding the reset bit. All clocks are functional, being controlled by configuration bits, while data path reset is active. The LIU and CLAD circuits will be operating normally during data path reset, which allows the internal phase locked loops to settle as quickly as possible. The LIU will be sending all zeroes (LOS) since data path reset will be forcing the transmit TPOSn and TNEGn to logic zero. (NOTE: The BERT data path and control registers are reset when the global data path reset or the port data path reset or the port power-down signal is active.) The global data path reset bit (GL.CR1.RSTDP) gets set to one when the global reset signal is active. The port data path reset bit (PORT.CR1.RSTDP) and the port power-down bit (PORT.CR1.PD) bit get set to one when the global reset signal is active or the port reset signal is active. These control bits will be cleared when a zero is written to them if the global reset signal or the port reset signal is not active. The global data path reset signal is active when the global data path reset bit is set. The port data path reset signal is active when either the global data path reset bit or the port data path reset bit is set. The port power-down signal is active when the port powerdown bit is set. Figure 10-5. Reset Sources Global Reset RST pin NOTE: Assumes active high signals Port Reset D SET CLR Q D GL.CR1. RST Q SET CLR Q Q PORT.CR1. RST Global Data Path Reset D SET D Q SET Q Port Data Path Reset GL.CR1. RSTDP CLR Q CLR Q PORT.CR1. RSTDP D SET CLR Q Q PORT.CR1. PD 107 Port Power Down DS3181/DS3182/DS3183/DS3184 Table 10-10. Reset and Power-Down Sources Port power Dan P:PD F1 F0 F1 F1 1 1 1 1 1 1 1 F1 F0 F1 F1 1 1 1 1 1 1 0 1 1 F1 F1 0 1 1 1 1 1 0 1 0 X 1 0 1 0 1 1 1 0 1 0 X 0 0 1 0 1 0 1 0 0 1 F1 F1 0 0 1 1 1 1 0 0 0 1 1 0 0 0 1 1 1 0 0 0 1 0 0 0 0 1 0 1 0 0 0 0 1 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 Port DP reset P:RSTDP Port reset P:RST F0 Global reset G:RSTDP 0 RST G:RST Global DP reset Register bit states - F0: Forced to 0, F1: Forced to 1, 0: Set to 0, 1: Set to 1, X: Don't care Forced: Internally controlled Set: User controlled PIN REGISTER BITS INTERNAL SIGNALS The reset signals in the device are asynchronous so they no not require a clock to put the logic into the reset state. Clock signals may be needed to make the logic come out of the reset state. The power-down function disables the appropriate clocks to cause the logic to generate a minimum of power. It also puts the LIU circuits into the power-down mode. Note that the UTOPIA/POS-PHY system interface logic cannot be powered down, the clocks cannot be stopped. The 8KREF and ONESEC circuits can be powered down by disabling the 8KREF source. The CLAD can also be powered down by disabling it. After a global reset, all of the control and status registers in all ports are set to their default values and all the other flops are reset to their reset values. The global register GL.CR1.RSTDP, and the port register PORT.CR1.RSTDP and PORT.CR1.PD bits in all ports, are set after the global reset. A valid initialization sequence would be to clear the PORT.CR1.PD bits in the ports that are to be active, write to all of the configuration registers to set them in the desired modes, then clear the GL.CR1.RSTDP and PORT.CR1.RSTDP bits. This would cause the logic in the ports to start up in a repeatable sequence. The device can also be initialized by clearing the GL.CR1.RSTDP, PORT.CR1.RSTDP and PORT.CR1.PD them writing to all of the configuration registers to set them in the desired modes, and clearing all of the latched status bits. The second initialization scheme could cause the device to temporarily go into modes of operation that were not requested, but will quickly go into the requested modes of operation. Some of the IO pins are put in a known state at reset. The transmit LIU outputs TXPn and TXNn are quiet and will not drive positive or negative pulses. The global IO pins (GPIO[7:0]) are set as inputs at global reset. The port output pins (TLCLKn, TPOSn/TDATn, TNEGn/TOHMOn, TOHCLKn, TOHSOFn, TPOHSOFn/TSOFOn/TDENn/ TFOHENOn, TPOHCLKn/TCLKOn/TGCLKn, ROHn, ROHCLKn, ROHSOFn, RPOHn/RSERn, RPOHSOFn/RSOFOn/RDENn/RFOHENOn, RPOHCLKn/RCLKOn/RGCLKn) are driven low at global or port reset and should stay low until after the port power-down PORT.CR1.PD and port data path reset PORT.CR1.RSTDP bits are cleared. The CLAD clock pins CLKA, CLKB and CLKC are the LIU reference clock inputs at global reset. The system interface three-state output pins (TDXA[1]/TPXA, TSPA, RDATA[31:0], RPRTY, RDXA[1]/RPXA/RSX, RSOX, REOP, RVAL, RMOD[1:0], RERR) are in the high impedance and the system interface output pins (TDXA[4:2],RDXA[4:2]) are driven low at global reset. The processor port three-state output pins (D[15:0], RDY, INT) are forced into the high impedance state when the RST pin is active, but not when the GL.CR1.RST bit is active. 108 DS3181/DS3182/DS3183/DS3184 After reset, the device will be in the default configuration:: The latched status bits are enabled to be cleared on write. The CLAD is disabled. The global 8KREF and one-second timers are disabled. The line interface is in B3ZS mode and the LIU is disabled and the transmit line pins are also disabled. The frame mode is DS3 C-bit with automatic downstream AIS on LOS or OOF is enabled and automatic RDI on LOF, LOS, SEF or AIS is enabled and automatic FEBE is enabled. Transmit clock comes from the CLAD CLKA pin. Cell processing is enabled with payload scrambling and HEC recalculation and Coset addition enabled. The transmit and receive FIFOs are held in reset so no cell traffic will occur until the FIFOs are configured. The system interface is in 8-bit UTOPIA L2 with odd parity enabled and HEC transfer disabled. The pin inversion on all pins is disabled. Individual blocks are reset and powered down when not used determined by the settings in the line mode bits PORT.CR2.LM[2:0] and framer mode bits PORT.CR2.FM[5:0]. 10.4 Global Resources 10.4.1 Clock Rate Adapter (CLAD) The clock rate adapter is used to create multiple clocks for LIU reference clocks or transmit clocks from a single clock reference input on the CLKA pin. The clock frequency applied to this pin must be at the DS3 (44.736 MHz), E3 (34.368 MHz) and STS-1 (51.84 MHz) clock rates. Given one of these clocks the other two clocks will be generated. The internally generated signals can be driven on output pins (CLKB and CLKC) for external use. The receive LIU is supplied a reference clock from the CLAD. The receive LIU selects the clock frequency based upon the mode the user selects via the FM bits. The CLAD output is also available as a transmit clock source if selected via the PORT.CR2.CLADC register bit. The user must supply at least one of the three rates (DS3, E3, STS-1) to the CLKA pin. The CLAD[3:0] bits informs the PLL of the frequency applied to the pins. Selection of the output clock of the CLAD applied to the LIU and optionally the transmitter is controlled by the FM bits (located in PORT.CR2). The CLAD allows maximum flexibility to the user. The user may supply any of the three clock rates and use the CLAD to convert the rate to the particular clock rate needed for his application. 109 DS3181/DS3182/DS3183/DS3184 Figure 10-6. CLAD Block DS3 clock CLKA CLKB CLAD E3 clock CC52 clock CLKC CLAD MODE The clock rate adapter can also be disabled and all three clocks supplied externally using the CLKA, CLKB and CLKC pins as clock inputs. When the CLAD is disabled, the three reference clocks DS3, E3 and STS-1 will need to be applied to the CLKA, CLKB and CLKC pins, respectively. If any of the three frequencies is not required, it does not need to be applied to the CLAD CLK pins. The CLAD MODE inputs to the clock rate adapter are composed of CLAD[3:0] control bits (located in the GL.CR2 Register) which determines which pins are input and output and which clock rate is on which pin. When CLAD[3:0]=00XX, the PLL circuits are disabled and the signals on the input clock pins are used as the internal LIU reference clocks. When CLAD[3:0]=(01XX or 10XX or 11XX), none, one or two PLL circuits are enabled to generate the required clocks as determined by the CLAD[3:0] bits and the framing mode (FM[5:0]) and the line mode (LM[2:0]) control bits. If a clock rate is not required on the CLAD output clock pins or for a reference clock for any of the LIU, then the PLL used to generate that clock is disabled and powered down. For example, in a design that only has the ports running at DS3 rates, then CLAD[3:0] can be set = 0100 and the DS3 clock signal on the CLKA pin will be used as the DS3 LIU reference clock and no PLL circuit will be disabled. 110 DS3181/DS3182/DS3183/DS3184 Table 10-11. CLAD IO Pin Decode GL.CR2 CLAD[3:0] 00 XX DS3 clock input E3 clock input STS-1 clock input 01 00 DS3 clock input Low output Low output 01 01 DS3 clock input E3 clock output Low output 01 10 DS3 clock input Low output STS-1 clock output 01 11 DS3 clock input STS-1 clock output E3 clock output 10 00 E3 clock input Low output Low output 10 01 E3 clock input DS3 clock output Low output 10 10 E3 clock input Low output STS-1 clock output 10 11 E3 clock input STS-1 clock output DS3 clock output 11 00 STS-1 clock input Low output Low output 11 01 STS-1 clock input E3 output Low output 11 10 STS-1 clock input Low output DS3 clock output 11 11 STS-1 clock input DS3 clock output E3 clock output CLKA PIN CLKB PIN CLKC PIN 10.4.2 8 kHz Reference Generation The 8KREF signal is used to control the rate of PLCP frames to precisely 8000 per second. The global 8KREF signal is also used to generate the one-second-reference signal by dividing it by 8000. This signal can be derived from almost any clock source on the chip as well as the general-purpose IO pin GPIO4. The port 8KREF signal can be sourced from either the global 8KREF signal or from the transmit or receive port clock or from the receive 8KREF signal. The minimum input frequency stability of the 8KREF input pin is +/- 500 ppm. The global 8KREF signal can come from an external 8000 Hz reference connected to the GPIO4 general-purpose IO pin by setting the GL.CR2.G8KIS bit. The global 8KREF signal can be output on the GPIO2 general-purpose IO pin when the GL.CR2.G8KOS bit is set. The global 8KREF signal can be derived from the CLAD PLL or pins or come from any of the port 8KREF signals by clearing GL.CR2.G8KIS bit and selecting the source using the GL.CR2.G8KRS[2:0] bits. The port 8KREF signal can be derived from either the receive PLCP 8KREF signal or from the transmit clock input pin or from the receive LIU or input clock pin. The PORT.CR3.P8KRS[1:0] bits are used to select which source. The transmit PLCP 8KREF signal can be selected to be either the global 8KREF signal or the port 8KREF signal using the PORT.CR3.P8KREF bit. The 8KREF 8.000 kHz signal is a simple divisor of 51840 kHz (CC52 divided by 6480), 44736 kHz (DS3 divided by 5592) or 33368 kHz (E3 divided by 4296). The correct divisor for the port 8KREF source is selected by the mode the port is configured for. The CLAD clock chosen for the clock source selects the correct divisor for the global 8KREF. The 8KREF signal is only as accurate as the clock source chosen to generate it. Table 10-12 lists the selectable sources for global 8 kHz reference sources. 111 DS3181/DS3182/DS3183/DS3184 Table 10-12. Global 8 kHz Reference Source Table GL.CR2. G8KIS 0 GL.CR2. G8KRS[2:0] 000 SOURCE None, the 8KHZ divider is disabled. Derived from CLAD DS3 clock output or CLKA pin if CLAD 0 001 is disabled (Note: CLAD is disabled after reset) Derived from CLAD E3 clock output or CLKB pin if CLAD is 0 010 disabled Derived from CLAD STS-1 clock output or CLKC pin if CLAD 0 011 is disabled 0 100 Port 1 8KREF source selected by P8KRS[1:0] 0 101 Port 2 8KREF source selected by P8KRS[1:0] 0 110 Port 3 8KREF source selected by P8KRS[1:0] 0 111 Port 4 8KREF source selected by P8KRS[1:0] 1 XXX GPIO4 pin Table 10-13 lists the selectable sources for port 8 kHz reference sources. Table 10-13. Port 8 kHz Reference Source Table PORT.CR3.P8KRS[1:0] 0X SOURCE Receive PLCP 8kHZ output Receive internal framer clock (based on RLCLKn 10 pin or RX LIU recovered clock) Transmit internal framer clock (based on TCLKIn 11 pin or CLAD clock) The 8 kHz reference logic tree is shown below. Figure 10-7. 8KREF Logic GL.CR2. G8KRS[1:0] FROM CLAD DS3 CLK E3 CLK CC52 CLK 1 2 3 GL.CR2.G8KRS[2] 0 CLOCK DIVIDER 1 GL.CR2.G8KRS[1:0] G8KREF 0 1 2 3 OTHER PORT 8KREF 0 GLOBAL 8KREF 1 GPIO4 PORT.CR3.P8KREF 0 PORT.CR3. P8KRS[1] RX PLCP 8KREF PORT.CR3.P8KRS[0] RX CLOCK TX CLOCK 0 0 1 1 CLOCK DIVIDER FRAME MODE (FM BITS) 112 1 TX PLCP 8KREF PORT 8KREF DS3181/DS3182/DS3183/DS3184 10.4.3 One-Second Reference Generation The one-second-reference signal is used as an option to update the performance registers on a precise onesecond interval. The generated internal signal should be about 50% duty cycle and it is derived from the Global 8kHz reference signal by dividing it by 8000. The low to high edge on this signal will set the GL.SRL.ONESL latched one second detect bit which can generate an interrupt when the GL.SRIE.ONESIE interrupt enable bit is set. The low to high edge can also be used to generate performance monitor updates when GL.CR1.GPM[1:0]=1X. 10.4.4 General-Purpose IO Pins There are eight general-purpose IO pins that can be used for general IO, global signals and per-port alarm signals. Each pin is independently configurable to be a general-purpose input, general-purpose output, global signal or port alarm. Two of the GPIO pins are assigned to each port and can be programmed to output one or two alarm statuses using one or two GPIO pins. One of the two pins assigned to each port can be programmed as global input or output signals. When the device is bonded out (or has ports powered down) to have 1, 2 or 3 ports active, the GPIO pins associated with the disabled ports will still operate as either general-purpose inputs, generalpurpose outputs or global signals. When the ports are disabled and GL.GIOCR.GPIOx[1:0] = 01, the GPIO pin will be an output driving low. The 8KREFI, TMEI, and PMU signals that can be sourced by the GPIO pin will be driven low into the core logic when the GPIO pin is not selected for the source of the signal. Table 10-14 lists the purpose and control thereof of the General-Purpose IO Pins. Table 10-14. GPIO Global Signals PIN GLOBAL SIGNAL CONTROL BIT GPIO2 8KREFO output GL.CR2.G8KOS GPIO4 8KREFI input GL.CR2.G8KIS GPIO6 TMEI input GL.CR1.MEIMS GPIO8 PMU input GL.CR1.GPM[1:0] Table 10-15 describes the selection of mode for the GPIO Pins. Table 10-15. GPIO Pin Global Mode Select Bits GL.GIOCR.GPIOnSx GPIO PIN MODE 00 Input 01 Port alarm status selected by port GPIO 10 Output logic 0 11 Output logic 1 n = port 1 to 4, x = A or B, valid when a GPIO pin is not selected for a global signal Table 10-16 lists the various port alarm monitors that can be output on the GPIO pins. The GPIO(A/B)[3:0] bits are located in the PORT.CR4 Register. 113 DS3181/DS3182/DS3183/DS3184 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 ATM LCD ATM OCD PLCP RAI PLCP LOF PLCP OOF DS3 IDLE DS3/E3 RAI DS3/E3 AIS DS3/E3 LOF DS3/E3 OOF PORT.CR4 GPIO(A/B)[3:0] LINE LOS Table 10-16. GPIO Port Alarm Monitor Select X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X 10.4.5 Performance Monitor Counter Update Details The performance monitor counters are designed to count at least one second of events before saturating to the maximum count. There is a status bit associated with some of the performance monitor counters that is set when the its counter is greater than zero, and a latched status bit that gets set when the counter changes from zero to one. There is also a latched status bit that gets set on every event that causes the error counter to increment. There is a read register for each performance monitor counter. The count value of the counter gets loaded into this register and the counter is cleared when the update-clear operation is performed. If there is an event to be counted at the exact moment (clock cycle) that the counter is to be cleared then the counter will be set to a value of one so that that event will be counted. The Performance Monitor Update signal affects the counter registers of the following blocks: the BERT, the DS3/E3 framer, the Line Encoder/Decoder, the DS3/E3 PLCP framer, the Cell Processor, and the Packet Processor. The update-clear operation is controlled by the Performance Monitor Update signal (PMU). The update-clear operation will update the error counter registers with the value of the error counter and also reset each counter. The PMU signal can be created in hardware or software. The hardware sources can come from the one second counter or one of the general-purpose IO pins, which can be programmed to source this signal. The software sources can come from one of the per-port control register bits or one of the global control register bits. When using the software update method, the PMU control bit should be set to initiate the process and when the PMS status bit gets set, the PMU control bit should be cleared making it ready for the next update. When using the hardware update method, the PMS bit will be set shortly after the hardware signal goes high, and cleared shortly after the hardware signal goes low. The latched PMS signal can be used to generate an interrupt for reading the count registers. If the port is not configured for global PMU signals, the PMS signal from that port should be blocked from affecting the global PMS status. 114 DS3181/DS3182/DS3183/DS3184 Figure 10-8. Performance Monitor Update Logic PORT.CR1.PMUM other port counters PORT.CR1.PMU GL.CR1.GPMU GPIO8(GPMU) PIN ONE SEC 0 PMU 00 01 1X 1 PMS PERF COUNTER other ports GL.SR.GPMS PORT.SR.PMS GTZ GL.CR1.GPM 10.4.6 Transmit Manual Error Insertion Transmit errors can be inserted in some of the functional blocks. These errors can be inserted using register bits in the functional blocks, using the global GL.CR1.TMEI bit, using the port PORT.CR1.TMEI bit, or by using the GPIO6 pin configured for TMEI mode. There is a transmit error insertion register in the functional blocks that allow error insertion. The MEIMS bit controls whether the error is inserted using the bits in the error insertion register or using error insertion signals external to that block. When bit MEIMS=0, errors are inserted using other bits in the transmit error insertion register. When bit MEIMS=1, errors are inserted using a signal generated in the port or global control registers or using the external GPIO6 pin configured for TMEI operation. 115 DS3181/DS3182/DS3183/DS3184 Figure 10-9. Transmit Error Insert Logic BERT.TEICR.MEIMS BERT.TEICR error insertion bit 0 PORT.CR.MEIMS PORT.CR.TMEI 1 0 BERT ERROR INSERT T3.TEIR.MEIMS GL.CR1.MEIMS 1 GL.CR1.TMEI 0 GPIO6 PIN (TMEI) 1 T3.TEIR error insertion bit 0 1 T3 ERROR INSERT 0 1 10.5 Per-Port Resources 10.5.1 Loopbacks There are several loopback paths available. The following table lists the loopback modes available for analog loopback (ALB), line loopback (LLB), payload loopback (PLB) and diagnostic loopback (DLB). System loopback (SLB) does not interact with these loopbacks and is given its own control bit. The LBM bits are located in PORT.CR4. Table 10-17. Loopback Mode Selections LBM[2:0] 000 001 010 011 10X 110 111 ALB 0 1 0 0 0 0 0 LLB 0 0 1 0 0 1 0 PLB 0 0 0 1 0 0 0 DLB 0 0 0 0 1 1 1 116 DS3181/DS3182/DS3183/DS3184 Figure 10-10 highlights where each loopback mode is located and gives an overall view of the various loopback paths available. Figure 10-10. Loopback Modes TAIS TUA1 IEEE P1149.1 JTAG Test Access Port System Interface RX BERT Rx Packet Processor DS3 / E3 Receive Framer B3ZS/ HDB3 Decoder Clock Rate Adapter TX BERT HDLC Tx FIFO Tx Packet Processor SLB Trail FEAC Trace Buffer TX FRAC/ PLCP PLB DLB LLB ALB DS3/E3 Receive LIU Tx Cell Processor DS3 / E3 Transmit Formatter B3ZS/ HDB3 Encoder DS3/E3 Transmit LIU RX FRAC/ PLCP UA1 GEN Rx Cell Processor Rx FIFO Microprocessor Interface 10.5.1.1 Analog Loopback (ALB) Analog loopback is enabled by setting PORT.CR4.LBM[2:0] = 001. Analog loopback mode will not be enabled when the port is configured for loop timed mode (set via the PORT.CR3.LOOPT bit). The analog loopback is a loopback as close to the pins as possible. When both the TX and RX LIU is enabled, it loops back TXPn and TXNn to RXPn and RXNn, respectively. If the transmit signals on TXPn and TXNn are not terminated properly, this loopback path may have data errors or loss of signal. When the LIU is not enabled, it loops back TLCLKn, TPOSn / TDATn, TNEGn / TOHMOn to RLCLKn ,RPOSn / RDATn , RNEGn / ROHMIn. Figure 10-11. ALB Mux TXP TXN RXP RXN TX LIU RX LIU 117 DS3181/DS3182/DS3183/DS3184 10.5.1.2 Line Loopback (LLB) Line loopback is enabled by setting PORT.CR4.LBM[2:0] = X10. DLB and LLB are enabled at the same time when LBM[2:0] = 110, and only LLB is enabled when LBM[2:0] = 010. The clock from the receive LIU or the RLCLK pin will be output to the transmit LIU or TCLKOn pin. The POS and NEG data from the receive LIU or the RPOS and RNEG pin will be sampled with the receive clock to time it to the LIU or pin interface. When LLB is enabled, unframed all ones AIS can optionally be automatically enabled on the receive data path. This AIS signal will be output on the RSERn pin in flexible fractional mode, and sent to the receive cell or packet processor in framer modes, effectively stopping cell or packet data flow. When DLB and LLB is enabled, the AIS signal will not be transmitted. See Figure 10-10. 10.5.1.3 Payload Loopback (PLB) Payload loopback is enabled by setting PORT.CR4.LBM[2:0] = 011. The payload loopback copies the payload data from the receive framer to the transmit framer (before the fractional logic) which then re-frames the payload before transmission. Payload loopback is operational in all framing modes except "- OHM" modes. When PLB is enabled, unframed all ones AIS transmission can optionally be automatically enabled on the receive data path. This AIS signal will be output on the RSER pin in flexible fractional mode, and sent to the receive cell or packet processor in framer modes, effectively stopping cell or packet data flow. In all modes, the TSOFIn input pin is ignored. The external transmit output pins TDENn and TSOFOn/TDENn can optionally be disabled by forcing a zero when PLB is enabled. In the framed modes, the data flow from the transmit cell or packet processor can be optionally disabled when PLB is enabled. If the data flow is not disabled, the cells or packets from the system interface will be discarded. See Figure 10-10. 10.5.1.4 Diagnostic Loopback (DLB) Diagnostic loopback is enabled by setting PORT.CR4.LBM[2:0] = 1XX. DLB and LLB are enabled at the same time when LBM[2:0] = 110, only DLB is enabled when LBM[2:0] = 10X or 111. The Diagnostic loopback sends the transmit data, before line encoding, back to the receive side. Transmit AIS can still be enabled using PORT.CR1.LAIS[2:0] even when DLB is enabled. See Figure 10-10. 10.5.1.5 System Loopback (SLB) System loopback is enabled by setting the PORT.CR4.SLB bit. The system loopback sends the packets or cells from the transmit UTOPIA or POS-PHY interface back to the receive UTOPIA or POS-PHY interface. Cells and packets from the line interface will be discarded. See Figure 10-10. 10.5.2 Loss Of Signal Propagation The Loss Of Signal (LOS) is detected in the line decoder logic if the device is set for HDB3 or B3ZS line encoding. In unipolar (UNI) line interface modes and AMI modes LOS detection is disabled. The LOS signal from the line decoder is sent to the DS3/E3 framer and the top level payload AIS logic except when DLB is activated. When DLB is activated the LOS signal to the framer and AIS logic is never active. The LOS status in the line decoder status register is valid in all frame and loopback modes, though it is always off in the line interface is in the UNI mode. 10.5.3 AIS Logic There is AIS logic in both the framers and at the top level logic of the ports. The framer AIS is enabled by setting the TAIS bit in the appropriate framer transmit control register (T3, E3-G.751, E3-G.832, or Clear Channel). The top level AIS is enabled by setting the PORT.CR1.LAIS[2:0] bits (see Table 10-18). The AIS signal is an unframed all ones pattern or a DS3 framed 101010... pattern depending on the FM[5:0] mode bits. The DS3 Framed Alarm Indication Signal (AIS) is a DS3 signal with valid F-bits, M-bits, and P-bits (P1 and P2). The X-bits (X1 and X2) are set to one, all C-bits (CXY) are set to zero, and the payload bits are set to a 1010 pattern starting with a one 118 DS3181/DS3182/DS3183/DS3184 immediately after each overhead bit. The DS3 framed AIS pattern is only available in DS3 modes. The unframed all ones pattern is available in all framing and clear-channel modes including the DS3 modes. The transmit line interface can send both unframed all ones AIS and DS3 framed AIS patterns from either the AIS generator in the framer or the AIS generator at the top level. The AIS signal generated in the framer can be initiated and terminated without introducing any errors in the signal. When the unframed AIS signal is initiated or terminated, there will be no BPV or CV errors introduced, there will be framing errors if a framed mode is enabled. When the DS3 framed AIS signal is initiated or terminated, in addition to no BPV or CV errors, there should be no framing or P-bit (parity) or CP-bit errors introduced. The AIS signal generated at the top level will not generate BPV errors but may generate P-bit and CP-bit errors when the signal is initiated and terminated. The framed DS3 AIS signal will not cause the far end receiver to resync when the signal is initiated, but it may cause a re-sync when terminated if the DS3 frame position in the framer is changed while the DS3 AIS signal is being generated. A sequence of events can be executed which will enable the initiation and termination of DS3 AIS or unframed all ones at the top level without any errors introduced. The sequence will only work when the automatic AIS generation is not enabled. CV and P-bit errors can occur when AIS is automatically generated and cannot be avoided. This sequence to generate an error free DS# AIS at the top level is to have the DS3 AIS or unframed all ones signal initiate in the DS3 framer, and a few frames sent before initiating or terminating the DS3 AIS or unframed all ones at the top level. After the top level AIS signal is activated, the AIS signal in the framer can be terminated, DLB activated and diagnostic patterns generated. The DS3 AIS signal generated at the top level will not change frame alignment after starting even if the DS3 frame position in the framer is changed. The transmit line AIS generator at the top level can generate AIS signals even when the framer is looped back using DLB, but not when the line is looped back using LLB. The AIS signal generated in the framer will be looped back to the receive side when DLB is activated. The receive framer can detect both unframed all ones AIS and DS3 framed AIS patterns. When in DS3 framing modes, both framed DS3 AIS and unframed all ones can be detected. In E3 framing modes E3 AIS, which is unframed all ones, is detected. In clear-channel modes, unframed all ones is detected. The receive payload interface going to the RSERn pin or the PLCP, FRAC, BERT or ATM/PKT logic can have an unframed all ones AIS signal replacing the receive signal, this is called Payload AIS. The all ones AIS signal is generated from either the DS3/E3 framer or the downstream top level unframed all ones AIS generator. The unframed all ones AIS signal generated in the framer will be looped back to the transmit side when PLB is activated. The unframed all ones AIS signal generated at the top level will be sent to the RSERn pin and other receive logic, but not to the transmit side while PLB is activated. The top level AIS generator is used when a downstream AIS signal is desired while payload loopback is activated and is enabled by default after rest and must be cleared during configuration. Note that the downstream AIS circuit in the framer, when a DS3 mode is selected, enforces the OOF to be active for 2.5 ms before activating when automatic AIS in the framer is enabled. The top level downstream AIS will be generated with no delay when OOF is detected when automatic AIS at the top level is enabled. There is no detection of any AIS signal on the transmit payload signal from the TSERn pin or anywhere on the transmit data path. The transmit AIS generator at the top level can also be activated with a software bit or automatically when DLB is activated. The receive AIS generator in the framer can be activated with a software bit, and automatically when AIS, LOS or OOF are detected. The receive payload AIS generator at the top level can be activated with a software bit or automatically when LOS, DS3/E3 OOF, LLB or PLB is activated. When the port is configured for "- OHM" modes, the transmit DS3 AIS signal pattern generation is paused when the TOHMI signal is active. Also the receive DS3 AIS and unframed all ones detectors do not use the bits marked for overhead from the ROHMIn signal when DLB is not activated or the TOHMIn signal when DLB is activated. The payload unframed all ones overwrites the receive signal with all ones even in overhead bit positions. 119 DS3181/DS3182/DS3183/DS3184 Figure 10-12 shows the AIS signal flow through the device. Figure 10-12. AIS Signal Flow FRAMER 0 TRANSMIT LINE 1 optional B3ZS/ HDB3 encoder TRANSMIT PAYLOAD 0 0 0 1 1 1 TAIS TAIS DS3/ UA1 AIS LLB LINE/TRIBUTARY SIDE TSOFO PLB DS3/ UA1 AIS SYSTEM/ TRUNK SIDE DS3/UA1 AIS detector 1 optional B3ZS/ HDB3 decoder RECEIVE LINE 0 0 0 1 DLB UA1 AIS 1 DAIS UA1 AIS DAIS Table 10-18 lists the LAIS decodes for various line AIS enable modes. Table 10-18. Line AIS Enable Modes LAIS[1:0] PORT.CR1 FRAME MODE 00 DS3 Automatic AIS when DLB is enabled (PORT.CR4.LBM = 1XX) DS3AIS 00 E3 Automatic AIS when DLB is enabled UA1 00 Clear Channel Automatic AIS when DLB is enabled UA1 01 Any Send UA1 UA1 10 DS3 Send AIS DS3AIS 10 E3 or Clear Channel Send AIS UA1 11 Any Disable none DESCRIPTION 120 AIS CODE RECEIVE PAYLOAD DS3181/DS3182/DS3183/DS3184 Table 10-19 lists the PAIS decodes for various payload AIS enable modes. Table 10-19. Payload (Downstream) AIS Enable Modes PAIS[2:0] PORT.CR1 WHEN AIS IS SENT AIS CODE 000 Always UA1 001 When LLB (no DLB) active UA1 010 When PLB active UA1 011 When LLB(no DLB) or PLB active UA1 100 When LOS (no DLB) active UA1 101 When OOF active UA1 110 When OOF, LOS. LLB (no DLB), or PLB active UA1 111 Never none 10.5.4 Loop Timing Mode Loop timing mode is enabled by setting the PORT.CR3.LOOPT bit. This mode replaces the clock from the TCLKIn pin with the internal receive clock from either the RLCLKn pin if the RX LIU is disabled, or the recovered clock from the RX LIU if it is enabled. The loop timing mode can be activated in any framing or line interface mode. 10.5.5 HDLC Overhead Controller There is a single HDLC controller for use in line maintenance protocols. The DS3, E3 and PLCP framers share the same HDLC controller. Since the PLCP and DS3 or E3 framers can potentially use the HDLC controller at the same time, there is a select bit in the port control register to chose which one uses the HDLC controller (PORT.CR1.HDSEL). The port that does not get access to the HDLC controller will transmit all ones in the overhead bits that the HDLC controller would connect to. The external overhead ports can be used to connect to an external HDLC controller if both framers need the function. The data signal to the receive HDLC controller will be forced to a one while still being clocked when the framer (DS3, E3, or PLCP), to which the HDLC is connected, detects LOF or AIS. Forcing the data signal to all ones will cause an HDLC packet abort if the data started to look like a packet instead of allowing a bad, and possibly very long, HDLC packet. 10.5.6 Trail Trace There is a single Trail Trace controller for use in line maintenance protocols. The E3-G.832 and PLCP framers can use the trail trace controller and it is shared automatically since the E3-G.832 and PLCP framing cannot be enabled at the same time. 10.5.7 BERT There is a Bit Error Rate Test (BERT) circuit for each port for use in generating and detecting test signals in the payload bits. The BERT can generate and detect PRBS patterns up to 2^32-1 bits as well as repeating patterns up to 32 bits long. The generated BERT signal replaces the cells or packets from the system interface when the BERT is enabled by setting the PORT.CR1.BENA. The cells or packets from the system interface will still be processed using the same bit rate as when the BERT was not enabled. Any transmit cells will be simply discarded when the BERT is enabled, and any cells or packets on the line interface will be processed and sent to the system bus when the BERT is enabled. The TDENn and RDENn pins will still be active but the data on the TSERn pin will be discarded when the BERT is enabled. 121 DS3181/DS3182/DS3183/DS3184 10.5.8 Fractional Payload Controller The Fractional Payload Controller allows the user flexibility to control sub-rate datastreams. The Fractional Payload Controller performs fractional overhead/payload data multiplexing. Fractional overhead is sourced from either an internal register or the external interface. The allocation of the DS3/E3 payload is also controlled either internally (internally controlled mode) or through the external interface (externally controlled mode). The third option is Flexible Mode that allows the user to externally multiplex payload and overhead, bypassing the Fractional Payload Controller. 10.5.9 PLCP/Fractional port pins The PLCP/Fractional port pins are have multiple functions based on the framing mode the device is in as well as other pin mode select bits. 10.5.9.1 Transmit PLCP/Fractional port pins The transmit PLCP/Fractional pins are TSOFIn / TOHMIn, TPOHn / TFOHn / TSERn, TPOHENn / TFOHENIn / TPDENIn, TPOHSOFn / TSOFOn / TDENn / TFOHENOn, TPDENOn, TPDATn, and TPOHCLKn / TCLKOn / TGCLKn. They have different functions based on the framing mode and other pin mode bits. Unused input pin functions should drive a logic zero into the device circuits expecting a signal from that pin. The control bits that configure the pins' modes are PORT.CR2.FM[5:0], PORT.CR3.TPFPE, PORT.CR3.TSOFOS and PORT.CR3.TCLKS. Table 10-20 to Table 10-26 describe the function selected by the FM bits and other pin mode bits for the multiplexed pins. Table 10-20. TSOFIn/TOHMIn Input Pin Functions FM[5:0] PORT.CR2 PIN FUNCTION 0XXX00 (FRM) TSOFIn 0XXX1X (FRM) TSOFIn 0XXX01 (OHM) TOHMIn 1XX0X1 (OHM) TOHMIn 1XX0X0 (UFRM) Not used 1XX1XX (UFRM) Not used Table 10-21. TSERn/TPOHn/TFOHn Input Pin Functions FM[5:0] PORT.CR2 TPFPE PORT.CR3 PIN FUNCTION 0XX00X (FRM) X Not used 0XX010 (IFRAC) 0 Not used 0XX010 (IFRAC) 1 TFOHn 0XX011 (XFRAC) X TFOHn 0XX10X (PLCP) 0 Not used 0XX10X (PLCP) 1 TPOHn 0XX110 (FFRAC) X TSERn 1XX0XX (CLR) X Not used 122 DS3181/DS3182/DS3183/DS3184 Table 10-22. TPDENIn/TPOHENn/TFOHENIn Input Pin Functions FM[5:0] PORT.CR2 TPFPE PORT.CR3 PIN FUNCTION 0XX00X (FRM) X Not used 0XX010 (IFRAC) X Not used 0XX011 (XFRAC) X TFOHENIn 0XX10X (PLCP) 0 Not used 0XX10X (PLCP) 1 TPOHENn 0XX110 (FFRAC) X TPDENIn 1XXXXX (CLR) X Not used Table 10-23. TSOFOn/TDENn/TPOHSOFn/TFOHENOn Output Pin Functions TPFPE PORT.CR3 TSOFOS PORT.CR3 0XX00X (FRM) 0 X Low 0XX00X (FRM) 1 0 TDENn 0XX00X (FRM) 1 1 TSOFOn 0XX010 (IFRAC) 0 X Low 0XX010 (IFRAC) 1 X TFOHENOn 0XX011 (XFRAC) X 0 TDENn 0XX011 (XFRAC) X 1 TSOFOn 0XX10X (PLCP) 0 X Low 0XX10X (PLCP) 1 X TPOHSOFn 0XX110 (FFRAC) X 0 TDENn 0XX110 (FFRAC) X 1 TSOFOn 1XX0XX (CLR) X X Low FM[5:0] PORT.CR2 PIN FUNCTION 123 DS3181/DS3182/DS3183/DS3184 Table 10-24. TCLKOn/TGCLKn/TPOHCLKn Output Pin Functions FM[5:0] PORT.CR2 TPFPE PORT.CR3 TCLKS PORT.CR3 PIN FUNCTION 0XX00X (FRM) 0 X Low none 0XX00X (FRM) 1 0 TGCLKn TDENn 0XX00X (FRM) 1 1 TCLKOn none 0XX010 (IFRAC) 0 X Low none 0XX010 (IFRAC) 1 0 TGCLKn TFOHENOn 0XX010 (IFRAC) 1 1 TCLKOn none 0XX011 (XFRAC) X X TCLKOn none 0XX10X (PLCP) 0 X Low none 0XX10X (PLCP) 1 0 TPOHCLKn none 0XX10X (PLCP) 1 1 TCLKOn none 0XX110 (FFRAC) X 0 Low none 0XX110 (FFRAC) X 1 TCLKOn none 1XX0XX (CLR) 0 X Low none 1XX0XX (CLR) 1 X TCLKOn none GAP SOURCE Table 10-25. TPDATn Input Pin Functions FM[5:0] PORT.CR2 TPFPE PORT.CR3 PIN FUNCTION 0XX0XX (FRM) X Low 0XXX0X (FRM) X Low 0XX110 (FFRAC) X TPDATn 1XXXXX (CLR) X Low Table 10-26. TPDENOn Output Pin Functions FM[5:0] PORT.CR2 TPFPE PORT.CR3 PIN FUNCTION 0XX0XX (FRM) X Low 0XXX0X (FRM) X Low 0XX110 (FFRAC) X TPDENOn 1XXXXX (CLR) X Low 10.5.9.2 Receive PLCP/Fractional port pins The receive PLCP/Fractional pins are RPOHn / RSERn, RFOHENIn / RPDENIn, RPDATn, RPOHSOFn / RSOFOn / RDENn / RFOHENOn and RPOHCLKn / RCLKOn / RGCLKn. They have different functions based on the framing mode and other pin mode bits. Unused input pin functions should drive a logic zero into the device circuits expecting a signal from that pin. The control bits that configure these pins are PORT.CR2.FM[5:0], PORT.CR3.RPFPE, PORT.CR3.RSOFOS and PORT.CR3.RCLKS. Table 10-27 to Table 10-31 describe the function selected by the FM bits and other pin mode bits for the multiplexed pins. 124 DS3181/DS3182/DS3183/DS3184 Table 10-27. RSERn/RPOHn Output Pin Functions FM[5:0] PORT.CR2 RPFPE PORT.CR3 PIN FUNCTION 0XX00X (FRM) 0 Low 0XX00X (FRM) 1 RSERn 0XX010 (IFRAC) 0 Low 0XX010 (IFRAC) 1 RSERn 0XX011 (XFRAC) X RSERn 0XX10X (PLCP) 0 Low 0XX10X (PLCP) 1 RPOHn 0XX110 (FFRAC) X RSERn 1XX0XX (CLR) 0 Low 1XX0XX (CLR) 1 RSERn Table 10-28. RPDENIn/RFOHENIn Input Pin Functions FM[5:0] PORT.CR2 RPFPE PORT.CR3 PIN FUNCTION 0XX00X (FRM) X Not used 0XX010 (IFRAC) X Not used 0XX011 (XFRAC) X RFOHENIn 0XX10X (PLCP) X Not used 0XX110 (FFRAC) X RPDENIn 1XXXXX (CLR) X Not used Table 10-29. RPDATn Input Pin Functions FM[5:0] PORT.CR2 RPFPE PORT.CR3 PIN FUNCTION 0XX0XX (FRM) X Not used 0XXX0X (FRM) X Not used 0XX110 (FFRAC) X RPDATn 1XXXXX (CLR) X Not used 125 DS3181/DS3182/DS3183/DS3184 Table 10-30. RSOFOn/RDENn/RPOHSOFn/RFOHENOn Output Pin Functions FM[5:0] PORT.CR2 RPFPE PORT.CR3 RSOFOS PORT.CR3 PIN FUNCTION 0XX00X (FRM) 0 X Low 0XX00X (FRM) 1 0 RDENn 0XX00X (FRM) 1 1 RSOFOn 0XX010 (IFRAC) 0 X Low 0XX010 (IFRAC) 1 X RFOHENOn 0XX011 (XFRAC) X 0 RDENn 0XX011 (XFRAC) X 1 RSOFOn 0XX10X (PLCP) 0 X Low 0XX10X (PLCP) 1 X RPOHSOFn 0XX110 (FFRAC) X 0 RDENn 0XX110 (FFRAC) X 1 RSOFOn 1XX0XX (CLR) X X Low Table 10-31. RCLKOn/RGCLKn/RPOHCLKn Output Pin Functions FM[5:0] PORT.CR2 RPFPE PORT.CR3 RCLKS PORT.CR3 PIN FUNCTION 0XX00X (FRM) 0 X Low none 0XX00X (FRM) 1 0 RGCLKn RDEN 0XX00X (FRM) 1 1 RCLKOn none 0XX010 (IFRAC) 0 X Low none 0XX010 (IFRAC) 1 0 RGCLKn RFOHENOn 0XX010 (IFRAC) 1 1 RCLKOn none 0XX011 (XFRAC) X X RCLKOn none 0XX10X (PLCP) 0 X Low none 0XX10X (PLCP) 1 0 RPOHCLKn none 0XX10X (PLCP) 1 1 RCLKOn none 0XX110 (FFRAC) X 0 Low none 0XX110 (FFRAC) X 1 RCLKOn none 1XX0XX (CLR) 0 X Low none 1XX0XX (CLR) 1 X RCLKOn none 126 GAP SOURCE DS3181/DS3182/DS3183/DS3184 10.5.10 Framing Modes The framing modes are selected independently of the line interface modes using the PORT.CR2.FM[5:0] control bits. Different blocks are used in different framing modes. The bit error test (BERT) function can be enabled in any mode. The LIU, JA and line encoder/decoder blocks are selected by the line mode (LM[2:0]) code. The "- OHM" mode, also known as "externally defined frame mode", is a mode that allow the use of the external frame overhead bit mask pins TOHMIn, TOHMOn and ROHMIn. This mode allows external logic to select bit locations where another level of framing can add overhead bits such as SONET/SDH overhead bits. Payload loopback (PLB) is disabled in this mode. The "Clear-Channel--OHM Octet aligned" modes perform octet alignment to the overhead mask for ATM and packets and the packets become octet stuffed instead of bit stuffed. See Table 10-32. Table 10-32. Framing Mode Select Bits FM[5:0] FM[5:0] 0 00 000 0 00 001 0 00 010 0 00 011 0 00 100 0 00 101 0 00 110 0 01 000 0 01 001 0 01 010 0 01 011 0 01 100 0 01 101 0 01 110 0 10 000 0 10 001 0 10 010 0 10 011 0 10 100 0 10 101 0 10 110 0 11 000 0 11 001 0 11 010 0 11 011 0 11 100 0 11 101 0 11 110 1 00 0X0 1 00 001 1 00 011 1 01 0X0 1 01 001 1 01 011 1 1X 0X0 1 1X 001 1 1X 011 DESCRIPTION DS3 C-bit DS3 C-bit--OHM DS3 C-bit Internal Fractional DS3 C-bit External Fractional DS3 C-bit PLCP DS3 C-bit PLCP--OHM DS3 C-bit Flexible Fractional DS3 M23 DS3 M23--OHM DS3 M23 Internal Fractional DS3 M23 External Fractional DS3 M23 PLCP DS3 M23 PLCP--OHM DS3 M23 Flexible Fractional E3 G.751 E3 G.751--OHM E3 G.751 Internal Fractional E3 G.751 External Fractional E3 G.751 PLCP E3 G.751 PLCP--OHM E3 G.751 Flexible Fractional E3 G.832 E3 G.832--OHM E3 G.832 Internal Fractional E3 G.832 External Fractional Reserved Reserved E3 G.832 Flexible Fractional DS3 Clear Channel DS3 Clear-Channel--OHM DS3 Clear-Channel--OHM Octet aligned STS-1 Clear Channel STS-1 Clear-Channel--OHM STS-1 Clear-Channel--OHM Octet aligned E3 Clear Channel E3 Clear-Channel--OHM E3 Clear-Channel--OHM Octet aligned 127 LINE CODE B3ZS/AMI/UNI UNI B3ZS/AMI/UNI B3ZS/AMI/UNI B3ZS/AMI/UNI UNI B3ZS/AMI/UNI B3ZS/AMI/UNI UNI B3ZS/AMI/UNI B3ZS/AMI/UNI B3ZS/AMI/UNI UNI B3ZS/AMI/UNI HDB3/AMI/UNI UNI HDB3/AMI/UNI HDB3/AMI/UNI HDB3/AMI/UNI UNI HDB3/AMI/UNI HDB3/AMI/UNI UNI HDB3/AMI/UNI HDB3/AMI/UNI SYSTEM ATM/PKT ATM/PKT ATM/PKT ATM/PKT ATM ATM ATM/PKT ATM/PKT ATM/PKT ATM/PKT ATM/PKT ATM ATM ATM/PKT ATM/PKT ATM/PKT ATM/PKT ATM/PKT ATM ATM ATM/PKT ATM/PKT ATM/PKT ATM/PKT ATM/PKT FIGURE Figure 6-1 Figure 6-2 Figure 6-3 Figure 6-4 Figure 6-6 Figure 6-7 Figure 6-5 Figure 6-1 Figure 6-2 Figure 6-3 Figure 6-4 Figure 6-6 Figure 6-7 Figure 6-5 Figure 6-1 Figure 6-2 Figure 6-3 Figure 6-4 Figure 6-6 Figure 6-7 Figure 6-5 Figure 6-1 Figure 6-2 Figure 6-3 Figure 6-4 HDB3/AMI/UNI B3ZS/AMI/UNI UNI UNI B3ZS/AMI/UNI UNI UNI HDB3/AMI/UNI UNI UNI ATM/PKT ATM/PKT ATM/PKT ATM/PKT ATM/PKT ATM/PKT ATM/PKT ATM/PKT ATM/PKT ATM/PKT Figure 6-5 Figure 6-8 Figure 6-9 Figure 6-10 Figure 6-8 Figure 6-9 Figure 6-10 Figure 6-8 Figure 6-9 Figure 6-10 DS3181/DS3182/DS3183/DS3184 10.5.11 Mapping Modes Cells and packets are mapped into various internally generated frame structures or mapped with no framing or mapped into an externally generated frame structure. When ATM cells are mapped into an internally generated frame structure they are either directly mapped into a DS3 or E3 frame or they are mapped into a PLCP frame and then the PLCP frame is mapped into a DS3 or E3 frame. ATM cells are always delineated using bit-by-bit HEC searching except when byte aligned OHM modes are used, then HEC is searched for byte-by-byte. HDLC packets are always use the bit stuffing protocol searching bit-by-bit except when byte aligned OHM modes are used, then they use the byte stuffing protocol. PLCP framing is always searched for bit-by-bit. The following sections give examples of the major framed mapping configurations: 10.5.11.1 DS3 C-Bit or DS3 M23 (with C-Bit Generation) Direct and PLCP Mapping For direct mapping into DS3 C-bit and DS3 M23 (with C-bit generation) frames, ATM cells are nibble aligned or bit aligned, HDLC packets are always bit aligned. For PLCP mapping into DS3 C-bit and DS3 M23 (with C-bit generation) frames, the PLCP frame is always nibble aligned. The ATM cell nibble/bit alignment is controlled with the NAD bit in the PORT.CR1 register. Figure 10-13. DS3 C-Bit or DS3 M23 (with C-Bit Generation) Frame X1 84 F11 bits 84 bits X2 F21 C21 F22 C22 F23 C23 F24 P1 F31 C31 F32 C32 F33 C33 F34 P2 F41 C41 F42 C42 F43 C43 F44 M1 F51 C51 F52 C52 F53 C53 F54 M2 F61 C61 F62 C62 F63 C63 F64 M3 F71 C71 F72 C72 F73 C73 F74 C11 84 bits F12 84 bits C12 84 bits F13 84 bits C13 84 bits F14 84 bits 7 SubFrames 680 Bits In DS3 PLCP framing, the ATM cell is always cell aligned into the PLCP frame, HDLC packets cannot be mapped into PLCP frames. The DS3 PLCP frame can only be mapped into a DS3 C-bit frame or DS3 M23 (with generated C-bits) frame. The NAD control bit is ignored. 128 DS3181/DS3182/DS3183/DS3184 Figure 10-14. DS3 PLCP Frame A1 A2 P11 Z6 53 Payload Bytes (1 cell) A1 A2 P10 Z5 53 Payload Bytes A1 A2 P9 Z4 53 Payload Bytes A1 A2 P8 Z3 53 Payload Bytes A1 A2 P7 Z2 53 Payload Bytes A1 A2 P6 Z1 53 Payload Bytes A1 A2 P5 F1 53 Payload Bytes A1 A2 P4 B1 53 Payload Bytes A1 A2 P3 G1 53 Payload Bytes A1 A2 P2 M2 53 Payload Bytes A1 A2 P1 M1 53 Payload Bytes A1 A2 P0 C1 53 Payload Bytes Subframe (57 Bytes) 12 Subframes Trailer 13 or 14 Nibbles 10.5.11.2 DS3 M23 (with C-bits used as payload) Direct Mapping For direct mapping into DS3 M23 (with the C-bits used as payload) frames, ATM cells must be bit aligned, HDLC packets are always bit aligned. The NAD bit must be set to one in this mode when direct mapping ATM cells into DS3 M23 (with the C-bits used as payload) frames. NOTE: PLCP mapping into DS3 M23 (with the C-bits used as payload) frames will not operate correctly. 129 DS3181/DS3182/DS3183/DS3184 Figure 10-15. DS3 M23 (with C-Bits Used as Payload) Frame X1 84 bits F11 169 bits 169 bits F12 F13 169 bits F14 X2 F21 F22 F23 F24 P1 F31 F32 F33 F34 P2 F41 F42 F43 F44 M1 F51 F52 F53 F54 M2 F61 F62 F63 F64 M3 F71 F72 F73 F74 84 bits 7 SubFrames 680 Bits 10.5.11.3 E3 G.751 Direct and PLCP Mapping For direct mapping into E3 G.751 frames, ATM cells and HDLC packets are bit aligned. ATM cells can also be PLCP mapped to the E3 G.751 frame. When E3 PLCP mapping is used, the first four bits of the payload (E3 frame bits 13,14,15 and 16) are forced to be 1100 and the rest of the payload is used for the PLCP frame that is transmitted byte aligned and the NAD bit is ignored. Figure 10-16. E3 G.751 Frame FAS A N 376 Payload Bits 384 Payload Bits 4 Rows 384 Payload Bits 384 Payload Bits 384 bits In E3 PLCP framing, the ATM cell is always cell aligned into the PLCP frame, HDLC packets cannot be mapped into PLCP frames. The E3 PLCP frame can only be mapped into a E3 G.751 frame. The NAD control bit is ignored. 130 DS3181/DS3182/DS3183/DS3184 Figure 10-17. E3 PLCP Frame A1 A2 P8 Z3 53 Payload Bytes (1 cell) A1 A2 P7 Z2 53 Payload Bytes A1 A2 P6 Z1 53 Payload Bytes A1 A2 P5 F1 53 Payload Bytes A1 A2 P4 B1 53 Payload Bytes A1 A2 P3 G1 53 Payload Bytes A1 A2 P2 M2 53 Payload Bytes A1 A2 P1 M1 53 Payload Bytes A1 A2 P0 C1 53 Payload Bytes Subframe 9 Subframes Trailer 18 or 20 Bytes 10.5.11.4 Example E3 G.751 Internal Fractional Mapping The example E3 G.751 internal fractional mapping shown in Figure 10-16 is accomplished using the internal fractional block. The first four bits of the E3. G.751 payload is designated fractional overhead This is done by setting Section A (FRAC.TDASR) register of the fractional block to be overhead and setting its size to be four bits. The data group size (FRAC.TDGSR) register should be set to the length of the normal payload (1524) or any number greater than that. The four bits of fractional overhead (E3 frame bits 13,14,15 and 16) can be set to all ones, all zeros, or a 1010 pattern. Both ATM cell and HDLC packet mapping in this mode is bit aligned. The NAD bit is ignored. Figure 10-18. Example E3 G.751 Internal Fractional Frame FAS A N X X X X 372 Payload Bits 384 Payload Bits 4 Rows 384 Payload Bits 384 Payload Bits 384 bits 10.5.11.5 E3 G.832 Direct Mapping For mapping into E3 G.832 frames ATM cells are byte aligned or bit aligned, HDLC packets are always bit aligned. The ATM cell byte/bit alignment is controlled with the NAD bit in the PORT.CR1 register. The NAD bit is ignored when HDLC packets are mapped into the E3 G.832 frame. 131 DS3181/DS3182/DS3183/DS3184 Figure 10-19. E3 G.832 Frame FA1 FA2 58 Byte Payload EM 59 Byte Payload TR 59 Byte Payload MA 59 Byte Payload NR 59 Byte Payload GC 59 Byte Payload 9 Subframes 59 Byte Payload 59 Byte Payload 59 Byte Payload Subframe 10.5.12 Line Interface Modes The line interface modes can be selected semi-independently of the framing modes using the PORT.CR2.LM[2:0] control bits. The major blocks controlled are the transmit LIU (TX LIU), receive LIU (RX LIU), jitter attenuator (JA) and the line encoder/decoder. The line encoder/decoder is used for B3ZS, HDB3 and AMI line interface encoding modes. The line encoder-decoder block is not used for line encoding or decoding in the UNI mode but the BPV counter in it can be used to count external pulses on the RNEGn / RCLVn / ROHMn pin. In "OHM" modes, the line encoder-decoder does not count pulses on the RNEGn / RLCVn / ROHMn pin. The jitter attenuator (JA) can be off (OFF) or put in either the transmit (TX) or receive (RX) path with the TX LIU or RX LIU. Both TX LIU and RX LIU can be enabled (ON) or disabled (OFF). The "Analog Loopback" (ALB) is available when the LIU is enabled or disabled. It is an actual loopback of the analog positive and negative pulses from the TX LIU to the RX LIU when the LIU is enabled. If the LIU is disabled, it is a digital loopback of the TLCLK, TPOS, TNEG signals to the RLCLK, RPOS and RNEG signals. When the line is configured for B3ZS/HDB3/AMI line codes, the line codes are determined by the framing mode and the TZCDS and RZCDS control the AMI line mode selection bits in the line encoder/decoder blocks. The DS3 and CC52 framing modes select the B3ZS line coding, the E3 framing modes select the HDB3 line codes. See Table 10-33 for configuration. 132 DS3181/DS3182/DS3183/DS3184 Table 10-33. Line Mode Select Bits LM[2:0] LINE.TCR.TZSD AND LINE.RCR.RZSD LM[2:0] (PORT.CR2) 0 000 0 LINE CODE LIU JA B3ZS/HDB3 OFF OFF 001 B3ZS/HDB3 ON OFF 0 010 B3ZS/HDB3 ON TX 0 011 B3ZS/HDB3 ON RX 1 000 AMI OFF OFF 1 001 AMI ON OFF 1 010 AMI ON TX 1 011 AMI ON RX X 1XX UNI OFF OFF 133 DS3181/DS3182/DS3183/DS3184 10.6 UTOPIA/POS-PHY/SPI-3 System Interface 10.6.1 General Description The UTOPIA/POS-PHY system interface transports ATM cells or HDLC packets between the DS318x and an ATM or Link Layer device. In UTOPIA mode, the DS318x is connected to an ATM layer device and cells are transported via a UTOPIA L2 or UTOPIA L3 Bus. In POS-PHY packet mode, the DS318x is connected to a Link Layer device and the packets are transported via a POS-PHY 2 or a POS-PHY 3 (or SPI-3) Bus. In POS-PHY cell mode, the DS318x is connected to an ATM layer device and cells are transported via a POS-PHY 2 or a POS-PHY 3 (or SPI3) Bus. The system interface supports 8-bit, 16-bit, or 32-bit transfers at a rate of 66MHz or less. The receive direction removes cell/packet data for each port from the FIFO, and outputs the cell/packet data to the ATM/Link Layer device via the system interface. The transmit direction inputs the cell/packet data from the ATM/Link Layer device via the system interface, and stores the cell/packet data for each port in the FIFO. See Figure 10-20 for the location of the system interface block in the DS318x devices. Figure 10-20. System Interface Functional Diagram TAIS TUA1 Clock Rate Adapter B3ZS/ HDB3 Decoder IEEE P1149.1 JTAG Test Access Port Tx Packet Processor TX BERT HDLC DS3 / E3 Receive Framer RX BERT RX FRAC/ PLCP UA1 GEN Tx FIFO System Interface Trail Trace Buf f er PLB FEAC TX FRAC/ PLCP Tx Cell Processor SLB DLB LLB ALB DS3/E3 Transmit LIU DS3/E3 Receive LIU DS3 / E3 Transmit Formatter B3ZS/ HDB3 Encoder Rx Packet Processor Rx Cell Processor Rx FIFO Microprocessor Interface 10.6.2 Features * * * * * Programmable system interface type - When performing cell mapping/demapping, the system interface can be programmed as a UTOPIA Level 2 Bus, a UTOPIA Level 3 Bus, a POS-PHY Level 2 Bus, or a POS-PHY Level 3 (or SPI-3) Bus. When performing packet mapping/demapping, the system interface can be programmed as a POS-PHY Level 2 Bus or a POS-PHY Level 3 (or SPI-3) Bus. Selectable system interface bus width - The data bus can be a 32-bit, 16-bit, or 8-bit bus at operations speeds up to 66 MHz. Supports multiple ports on the system interface - Each line has its own port address for access via the system interface. Supports per-port system loopback - Each port can be placed in system loopback which causes cells/packets from the transmit FIFO to be looped back to the receive FIFO. System interface byte reordering - In 16-bit and 32-bit modes, the received/transmitted order of the bytes transferred across the system interface is programmable. i.e., the first byte received/transmitted by ATM cell / packet processing can be transferred in [31:24] ([15:8]) or [7:0]. 134 DS3181/DS3182/DS3183/DS3184 10.6.6 System Interface Bus Controller The Transmit and Receive System Interface Bus Controller can be programmed to operate as a UTOPIA Level 2, UTOPIA Level 3, POS-PHY Level 2, or POS-PHY Level 3 (or SPI-3) bus controller. It controls the system interface bus timing and provides a common interface to the Transmit and Receive FIFO for FIFO status polling and cell/packet data transfer. Normally, the first byte transmitted is transferred across the system interface as the most significant byte (TDATA[31:24] in 32-bit mode or TDATA[15:8] in 16-bit mode). If byte reordering is enabled, the first byte transmitted is transferred across the system interface as the least significant byte (TDATA[7:0]).On the receive side, the first byte received is transferred across the system interface as the most significant byte (RDATA[31:24] in 32-bit mode or RDATA[15:8] in 16-bit mode). If byte reordering is enabled, the first byte received is transferred across the system interface as the least significant byte (RDATA[7:0]). See Figure 10-21, Figure 10-22, Figure 10-23, and Figure 10-24. Byte reordering is ignored in 8-bit mode. Figure 10-21. Normal Packet Format in 32-Bit Mode Bit 31 Bit 0 Byte 1 Byte 2 Byte 3 Byte 4 1st Transfer Byte 5 Byte 6 Byte 7 Byte 8 2nd Transfer * * * * * * * * * * * * Byte 4n-7 Byte 4n-6 Byte 4n-5 Byte 4n-4 (n-1)th Transfer Byte 4n-3 Byte 4n-2 Byte 4n-1 Byte 4n nth Transfer Figure 10-22. Normal Packet Format in 16-Bit Mode Bit 15 Bit 0 Byte 1 Byte 2 1st Transfer Byte 3 Byte 4 2nd Transfer * * * * * * Byte 2n-3 Byte 2n-2 (n-1)th Transfer Byte 2n-1 Byte 2n nth Transfer Figure 10-23. Byte Reordered Packet Format in 32-Bit Mode Bit 31 Bit 0 Byte 4 Byte 3 Byte 2 Byte 1 1st Transfer Byte 8 Byte 7 Byte 6 Byte 5 2nd Transfer * * * * * * * * * * * * Byte 4n-4 Byte 4n-5 Byte 4n-6 Byte 4n-7 (n-1)th Transfer Byte 4n Byte 4n-1 Byte 4n-2 Byte 4n-3 nth Transfer 135 DS3181/DS3182/DS3183/DS3184 Figure 10-24. Byte Reordered Packet Format in 16-Bit Mode Bit 15 Bit 0 Byte 2 Byte 1 1st Transfer Byte 4 Byte 3 2nd Transfer * * * * * * Byte 2n-2 Byte 2n-3 (n-1)th Transfer Byte 2n Byte 2n-1 nth Transfer 10.6.6.4 UTOPIA Level 2, Transmit Side In UTOPIA Level 2, an ATM layer device pushes cells across the system interface. The ATM layer device polls the individual ports of the DS318x to determine which ports have space available for a cell, and selects a port for cell transfer. More than one PHY layer device can be present on a UTOPIA Level 2 bus. Whether or not the HEC byte is transferred with the cells is programmable. The Transmit System Interface Bus Controller accepts a transmit clock (TSCLK), transmit address (TADR[4:0]), transmit enable (TEN), and a transmit data bus consisting of transmit data (TDATA[31:0]), transmit parity (TPRTY), and transmit start of cell (TSOX). It outputs transmit direct cell available (TDXA) and transmit polled cell available (TPXA) signals. The transmit data bus is used to transfer cell data whenever one of the ports is selected for cell data transfer. TSOX is asserted during the first transfer of a cell, cell data is transferred on TDATA, and the data bus parity is indicated on TPRTY. All signals are sampled or updated using TSCLK. The TDXA and TPXA signals are used to indicate when the Transmit FIFO has space available for a programmable number of cells. There is a TDXA for each port in the device. TDXA goes high when the associated port's Transmit FIFO has more space available than a programmable number of cells. TDXA goes low when the associated port's Transmit FIFO is full (does not have space for another cell). TPXA reflects the current status of a port's TDXA signal when the port is polled. The TPXA signal is tri-stated unless one of the ports is being polled for FIFO fill status. 10.6.6.5 UTOPIA Level 3, Transmit Side In UTOPIA Level 3, the ATM layer device pushes cells across the system interface. The ATM layer device polls the individual ports of the DS318x to determine which ports have space available for a cell, and selects a port for cell transfer. Only one PHY layer device can be present on a UTOPIA Level 3 bus. Whether or not the HEC byte is transferred with the cells is programmable. The Transmit System Interface Bus Controller accepts a transmit clock (TSCLK), transmit address (TADR[7:0]), transmit enable (TEN), and a transmit data bus consisting of transmit data (TDATA[31:0]), transmit parity (TPRTY), and transmit start of cell (TSOX). It outputs transmit direct cell available (TDXA) and transmit polled cell available (TPXA) signals. The transmit data bus is used to transfer cell data whenever one of the ports is selected for cell data transfer. TSOX is asserted during the first transfer of a cell, cell data is transferred on TDATA, and the data bus parity is indicated on TPRTY. All signals are sampled or updated using TSCLK. The TDXA and TPXA signals are used to indicate when the Transmit FIFO has space available for a programmable number of cells. There is a TDXA for each port in the device. TDXA goes high when the associated port's Transmit FIFO has more space available than a programmable number of cells. TDXA goes low when the associated port's Transmit FIFO is full (does not have space for another cell). TPXA reflects the current status of a port's TDXA signal when the port is polled. The TPXA signal is always driven. 10.6.6.6 UTOPIA Level 2, Receive Side In UTOPIA Level 2, the ATM layer device pulls cells across the system interface. The ATM layer device polls the individual ports to determine which ports have cells available, and selects a port for cell transfer. More than one PHY layer device can be present on a UTOPIA Level 2 bus. Whether or not the HEC byte is transferred with the cells is programmable. The Receive System Interface Bus Controller accepts a receive clock (RSCLK), receive address (RADR[4:0]), and receive enable (REN). It outputs a receive data bus consisting of receive data (RDATA[31:0]), receive parity (RPRTY), and receive start of cell (RSOX), as well as, receive direct cell available (RDXA) and receive polled cell 136 DS3181/DS3182/DS3183/DS3184 available (RPXA) signals. The receive bus is used to transfer cell data whenever one of the ports is selected for cell data transfer. RSOX is asserted during the first transfer of a cell, cell data is transferred on RDATA, and the data bus parity is indicated on RPRTY. All signals are sampled or updated using RSCLK. The data bus is tri-stated unless REN is asserted (low) and one of the ports is selected for data transfer. The RDXA and RPXA signals are used to indicate when the Receive FIFO has a programmable number of cells available for transfer. There is an RDXA for each port in the device. RDXA goes high when the associated port's Receive FIFO contains more than a programmable number of cells. RDXA goes low when the associated port's Receive FIFO is empty (does not contain any cells). RPXA reflects the current status of a port's RDXA signal when the port is polled. The RPXA signal is tri-stated unless one of the ports is being polled for FIFO fill status. 10.6.6.2 UTOPIA Level 3, Receive Side In UTOPIA Level 3, the ATM layer device pulls cells across the system interface. The ATM layer device polls the individual ports to determine which ports have cells available, and selects a port for cell transfer. Only one PHY layer device can be present on a UTOPIA Level 3 bus. Whether or not the HEC byte is transferred with the cells is programmable. The Receive System Interface Bus Controller accepts a receive clock (RSCLK), receive address (RADR[7:0]), and receive enable (REN). It outputs a receive data bus consisting of receive data (RDATA[31:0]), receive parity (RPRTY), and receive start of cell (RSOX), as well as, receive direct cell available (RDXA) and receive polled cell available (RPXA) signals. The receive data bus is used to transfer cell data whenever one of the ports is selected for cell data transfer. RSOX is asserted during the first transfer of a cell, cell data is transferred on RDATA, and the data bus parity is indicated on RPRTY. All signals are sampled or updated using RSCLK. The data bus is always driven. The RDXA and RPXA signals are used to indicate when the Receive FIFO has a programmable number of cells available for transfer. There is an RDXA for each port in the device. RDXA goes high when the associated port's Receive FIFO contains more than a programmable number of cells. RDXA goes low when the associated port's Receive FIFO is empty (does not contain any cell ends). RPXA reflects the current status of a port's RDXA signal when the port is polled. The RPXA signal is always driven. 10.6.6.3 POS-PHY Level 2, Transmit Side In POS-PHY Level 2, the Link layer device pushes packets across the system interface. The Link layer device polls the individual ports of the DS318x to determine which ports have space available for packet data, and selects a port for packet data transfer. More than one PHY layer device can be present on a POS-PHY Level 2 bus. The Transmit System Interface Bus Controller accepts a transmit clock (TSCLK), transmit address (TADR[4:0]), transmit enable (TEN), and a transmit data bus consisting of transmit data (TDATA[31:0]), transmit parity (TPRTY), transmit start of packet (TSOX), transmit end of packet (TEOP), transmit error (TERR), and transmit modulus (TMOD[1:0]). It outputs transmit direct packet available (TDXA), transmit polled packet available (TPXA), and transmit selected packet available (TSPA) signals. The transmit data bus is used to transfer packet data whenever one of the ports is selected for packet data transfer. TSOX is asserted during the first transfer of a packet, TEOP is asserted during the last transfer of a packet, TERR is asserted when a packet has an error, TMOD indicates the number of bytes transferred on TDATA during the last transfer of a packet, packet data is transferred on TDATA, and the data bus parity is indicated on TPRTY. All signals are sampled and updated using TSCLK. The TDXA, TPXA, and TSPA signals are used to indicate when the Transmit FIFO has space available for a programmable number of bytes. There is a TDXA for each port in the device. TDXA goes high when the associated port's Transmit FIFO has space available for more than a programmable number of bytes. TDXA goes low when the associated port's Transmit FIFO is full. TPXA reflects the current status of a port's TDXA signal when the system interface is in polled mode. TSPA reflects the current status of a port's TDXA signal when the port is selected. The TSPA signal is tri-stated unless TEN is asserted (low) and one of the ports is selected for packet data transfer. The TPXA signal is tri-stated unless one of the ports is being polled for FIFO fill status. 10.6.6.4 POS-PHY Level 3 (or SPI-3), Transmit Side In POS-PHY Level 3 (or SPI-3), the Link layer device pushes packets across the system interface. The Link layer device polls the individual ports of the DS318x to determine which ports have space available for packet data, and selects a port for packet data transfer. Only one PHY layer device can be present on a POS-PHY Level 3 (or SPI3) bus. The Transmit System Interface Bus Controller accepts a transmit clock (TSCLK), transmit enable (TEN), and a transmit data bus consisting of transmit data (TDATA[31:0]), transmit parity (TPRTY), transmit start of packet (TSOX), transmit end of packet (TEOP), transmit error (TERR), transmit start of transfer (TSX), and transmit 137 DS3181/DS3182/DS3183/DS3184 modulus (TMOD[1:0]). It outputs transmit direct packet available (TDXA), transmit polled packet available (TPXA), and transmit selected packet available (TSPA) signals. The transmit bus is used to transfer packet data whenever one of the ports is selected for packet data transfer. TSOX is asserted during the first transfer of a packet, TEOP is asserted during the last transfer of a packet, TERR is asserted when a packet has an error, TMOD indicates the number of bytes transferred on TDATA during the last transfer of a packet, TSX is asserted when the selected FIFO's port address has been placed on TDATA, packet data is transferred on TDATA, and the data bus parity is indicated on TPRTY. All signals are sampled and updated using TSCLK. The TDXA, TPXA, and TSPA signals are used to indicate when the Transmit FIFO has space available for a programmable number of bytes. There is a TDXA for each port in the device. TDXA goes high when the associated port's Transmit FIFO has space available for more than a programmable number of bytes. TDXA goes low when the associated port's Transmit FIFO is full. TPXA reflects the current status of a port's TDXA signal when the port is polled. TSPA reflects the current status of a port's TDXA signal when the port is selected. The TPXA and TSPA signals are always driven. 10.6.6.5 POS-PHY Level 2, Receive Side In POS-PHY Level 2, the Link layer device pulls packets across the system interface. The Link layer device polls the individual ports to determine which ports have packet data available, and selects a port for packet data transfer. More than one PHY layer device can be present on a POS-PHY Level 2 bus. The Receive System Interface Bus Controller accepts a receive clock (RSCLK), receive address (RADR[4:0]), and receive enable (REN). It outputs a receive data bus consisting of receive data (RDATA[31:0]), receive parity (RPRTY), receive start of packet (RSOX), receive end of packet (REOP), receive error (RERR), receive data valid (RVAL), and receive modulus (RMOD[1:0]), as well as, a receive direct packet available (RDXA) signal and a receive polled packet available (RPXA) signal. The receive data bus is used to transfer packet data whenever one of the ports is selected for packet data transfer. RSOX is asserted during the first transfer of a packet, REOP is asserted during the last transfer of a packet, RERR is asserted when a packet has an error, RMOD indicates the number of bytes transferred on RDATA during the last transfer of a packet, RVAL is asserted when the receive data bus is valid, RDATA transfers packet data, and RPRTY indicates the data bus parity. All signals are sampled and updated using RSCLK. The RDXA and RPXA signals are used to indicate when the Receive FIFO has a programmable number of bytes or an end of packet available for transfer. There is an RDXA for each port in the device. RDXA goes high when the associated port's Receive FIFO contains more than a programmable number of bytes or an end of packet. RDXA goes low when the associated port's Receive FIFO is empty. RPXA reflects the current status of a port's RDXA signal when the port is polled. The data bus is tri-stated unless REN is asserted (low) and one of the ports is selected for packet data transfer. The RPXA signal is tri-stated unless one of the ports is being polled for FIFO fill status. 10.6.6.6 POS-PHY Level 3 (or SPI-3), Receive Side In POS-PHY Level 3, the DS318x pushes packets across the system interface. The DS318x selects a port for packet data transfer when it has packet data available. Only one PHY layer device can be present on a POS-PHY Level 3 (or SPI-3) bus. The Receive System Interface Bus Controller accepts a receive clock (RSCLK) and receive enable (REN). It outputs a receive data bus consisting of receive data (RDATA[31:0]), receive parity (RPRTY), receive start of packet (RSOX), receive end of packet (REOP), receive error (RERR), receive data valid (RVAL), receive start of transfer (RSX), and receive modulus (RMOD[1:0]). The receive data bus is used to transfer packet data whenever one of the ports has packet data available for transfer. RSOX is asserted during the first transfer of a packet, REOP is asserted during the last transfer of a packet, RERR is asserted when a packet has an error, RMOD indicates the number of bytes transferred on RDATA during the last transfer of a packet, RSX is asserted when the Link layer port address has been placed on RDATA, RVAL is asserted when the receive data bus is valid, RDATA transfers packet data, and RPRTY indicates the data bus parity. All signals are sampled and updated using RSCLK. The data bus is always driven. In POS-PHY Level 3 (or SPI-3) the Receive System Interface Bus Controller determines which port to transfer data from using a round-robin arbitration scheme (the ports are checked one after another in numerical order according to their line number x (R[x]DT[1:8]). A transfer is initiated from a port when it is not almost empty (contains more data than the almost empty level or contains an end of packet). Transfer from a port is terminated when the maximum burst length has been transferred, the FIFO is emptied, or an end of packet is transferred while the Receive FIFO is almost empty (contains the same or less data than the almost empty level and does not contain an end of packet). When a transfer is terminated, a transfer is initiated from the next available port that is not almost empty. At the end of a packet or between a transfer from one port and the transfer from the next port, RVAL will go low for a programmable number of clock cycles (0-7) to allow the POS-PHY master to halt data transfer. At the end 138 DS3181/DS3182/DS3183/DS3184 of a packet, data transfer will continue from the same port if the port is not almost empty. When the maximum burst length has been transferred, data transfer will continue from the same port if no other port has data available, and the port is not almost empty. The maximum burst length is programmable (8 - 256 bytes in four byte increments), or can be disabled. 10.7 ATM Cell/HDLC Packet Processing 10.7.1 General Description The ATM cell/packet processing demaps the ATM cells or HDLC packets from the receive data stream and maps ATM cells or HDLC packets into the transmit data stream. ATM cell / packet processing supports any framed or unframed bit synchronous or byte synchronous (octet aligned) data stream with a bit or byte rate of 52 MHz or less. The receive direction extracts the payload from physical data stream, performs cell/packet processing on the individual lines, and stores the cell/packet data from each line in the FIFO. The transmit direction removes the cell/packet data for each line from the FIFO, performs cell/packet processing for each individual line and inserts the payload into the physical data stream. See Figure 10-25 for the location of the Cell/Packet processing block in the DS318x devices. Figure 10-25. ATM Cell/HDLC Packet Functional Diagram TAIS TUA1 Clock Rate Adapter TX BERT HDLC B3ZS/ HDB3 Decoder DS3 / E3 Receive Framer IEEE P1149.1 JTAG Test Access Port RX BERT RX FRAC/ PLCP UA1 GEN Tx FIFO Tx Packet Processor System Interface Trail Trace Buf f er PLB FEAC TX FRAC/ PLCP Tx Cell Processor SLB DLB LLB ALB DS3/E3 Transmit LIU DS3/E3 Receive LIU DS3 / E3 Transmit Formatter B3ZS/ HDB3 Encoder Rx Packet Processor Rx Cell Processor Rx FIFO Microprocessor Interface 10.7.2 Features 10.7.2.1 General * * * Up to 4 data lines(ports) each with a bit or byte rate of 0-52 MHz Supports bit or byte wide, framed or unframed data lines - Each port is programmable as bit synchronous or octet aligned, the data stream can be framed or unframed, and the clock can be continuous or gapped. Bit reordering - The received/transmitted order of the bits as transferred across the system interface is programmable on a per-port basis. That is, in bit synchronous mode, the first bit received/transmitted by ATM cell/packet processing can be transferred in bit position 7 (31, 23, 15, or 7) or bit position 0 (24, 16, 8, or 0). In octet aligned mode, the bit received/transmitted by ATM cell/packet processing in bit position 7 can be transferred in bit position 7 (31, 23, 15, or 7) or bit position 0 (24, 16, 8, or 0). 139 DS3181/DS3182/DS3183/DS3184 10.7.2.2 ATM Cell Processor * * * * * * * * * * * Programmable HEC insertion and extraction - The transmit side can be programmed to accept cells from the system interface that do or do not contain a HEC byte. If cells are transferred without a HEC byte, the HEC byte will be computed and inserted. If cells are transferred with a HEC byte, then the transferred HEC byte can be programmed to be passed through or overwritten with a newly calculated HEC. The receive side can be programmed to send cells to the system interface that do or don't contain the HEC byte. Programmable erred cell insertion - An HEC error mask can be programmed for insertion of single or multiple errors individually or continuously at a programmable rate. Programmable transmit cell synchronization - The transmit data line can be provisioned to be bit synchronous or octet aligned. PLCP or HEC based cell delineation - Cell delineation is determined from the PLCP frame during PLCP framing modes, and from the HEC during all other ATM modes. Programmable header cell pass-through - Receive cell filtering can pass-through only those cells that matching a programmable header value. Selectable idle/unassigned/invalid/programmable header cell padding and filtering - Transmit cell padding can be programmed for idle cell or programmable header cell padding. The padded cell payload byte contents are also programmable. Receive cell filtering can be programmed for any combination of idle cell, unassigned cell, invalid cell, or programmable header cell filtering. Or, all cell filtering can be disabled. Optional header error correction - Receive side single bit header error correction can enabled. Separate corrected and uncorrected erred cell counts - Separate counts of erred cells containing a corrected HEC error, and cells containing non-corrected HEC errors are kept. Optional HEC uncorrected erred cell filtering - Uncorrected erred cell extraction can be disabled. Selectable cell scrambling/descrambling - Cell scrambling and/or descrambling can be disabled. The scrambling can be a self-synchronous scrambler (x43 + 1) over the payload only, a self-synchronous scrambler over the entire cell, or a Distributed Sample Scrambler (x31 + x28 + 1). Optional HEC calculation coset polynomial addition - The performance of coset polynomial addition during HEC calculation can be disabled. 10.7.2.3 HDLC Packet Processor * * * * * * * * * * Programmable FCS insertion and extraction - The transmit side can be programmed to accept packets from the system interface that do or don't contain FCS bytes. If packets are transferred without FCS bytes, the FCS will be computed and appended to the packet. If packets are transferred with FCS bytes, then the FCS can be programmed to be passed through or overwritten with a newly calculated FCS. The receive side can be programmed to send packets to the system interface that do or don't contain FCS bytes. Programmable transmit packet synchronization - The transmit data line can be provisioned to be bit synchronous or octet aligned. Programmable FCS type - The FCS can be programmed to be a 16-bit FCS or a 32-bit FCS. Supports FCS error insertion - FCS error insertion can be programmed for insertion of errors individually or continuously at a programmable rate. Supports bit or byte stuffing/destuffing - The bit or byte synchronous (octet aligned) mode determines the bit or byte stuffing/destuffing. Programmable packet size limits - The receive side can be programmed to abort packets over a programmable maximum size or under a programmable minimum size. The maximum packet size allowed is 65,535 bytes. Selectable packet scrambling/descrambling - Packet scrambling and/or descrambling can be disabled. Separate FCS erred packet and aborted packet counts - Separate counts of aborted packets, size violation packets, and FCS erred packets are kept. Optional erred packet filtering - Erred packet extraction can be disabled Programmable inter-frame fill - The transmit inter-frame fill value is programmable. 10.7.3 Transmit Cell/Packet Processor The Transmit Cell Processor and Transmit Packet Processor both receive the 32-bit parallel data stream from the Transmit FIFO, however, only one of the processors will be enabled. Which processor is enabled is determined by the system interface mode. In UTOPIA mode, the Transmit Cell Processor is enabled. In POS-PHY mode, if the PORT.CR2.PMCPE bit is low, the Transmit Packet Processor is enabled. If the PORT.CR2.PMCPE bit (PORT.CR2) is high, the Transmit Cell Processor is enabled. 140 DS3181/DS3182/DS3183/DS3184 10.7.4 Receive Cell/Packet Processor The Receive Cell Processor and Receive Packet Processor both receive the incoming data stream from the Receive Framer (minus all overhead and stuff data), however, only one of the processors will be enabled. The other will be disabled. Which processor is enabled is determined by the system interface mode. In UTOPIA mode, the Receive Cell Processor is enabled. In POS-PHY mode, if the PORT.CR2.PMCPE bit is low, the Receive Packet Processor is enabled. If the PORT.CR2.PMCPE bit is high, the Receive Cell Processor is enabled. The bits in a byte are received MSB first, LSB last. When they are output serially, they are output MSB first, LSB last. The bits in a byte in an incoming signal are numbered in the order they are received , 1 (MSB) to 8 (LSB). However, when a byte is stored in a register, the MSB is stored in the highest numbered bit (7], and the LSB is stored in the lowest numbered bit (0). This is to differentiate between a byte in a register and the corresponding byte in a signal. 10.7.5 Cell Processor 10.7.5.1 Transmit Cell Processor The Transmit Cell Processor accepts data from the Transmit FIFO and performs bit reordering, cell padding, HEC processing, cell error insertion, and cell scrambling. The data output from the Transmit Cell Processor can be either a serial data stream (bit synchronous mode) or an 8-bit parallel data stream (octet-aligned mode). Cell processing can be disabled (clear-channel enable). Disabling cell processing disables cell padding, HEC processing, and cell error insertion. Only bit reordering and cell scrambling are not disabled. When cell processing is disabled, data is continually read out of the Transmit FIFO. When the Transmit FIFO is empty, the output data stream is padded with FFh until the Transmit FIFO contains more data than the "almost empty" level. The 32-bit data words read from the Transmit FIFO are multiplexed into an 8-bit parallel data stream and passed on to bit reordering. Bit reordering changes the bit order of each byte. If bit reordering is enabled, the incoming 8-bit data stream DT[7:0] with DT[7] being the MSB and DT[0] being the LSB is rearranged so that the MSB is in DT[0] and the LSB is in DT[7] of the outgoing data stream DT[7:0]. In bit synchronous mode, DT[7] is the first bit transmitted. If cell processing is disabled the data stream is passed on to cell scrambling, bypassing cell padding, HEC processing, and cell error insertion. Cell padding inserts fill cells. After a cell end, fill cells are inserted into the data stream if the Transmit FIFO does not contain a complete cell. The fill cell type and fill cell payload value are programmable. The resulting data stream is passed on to HEC processing. If cell processing is disabled, cell padding will not be performed. HEC processing calculates a HEC and inserts it into the cell. HEC calculation is a CRC-8 calculation over the four header bytes. The polynomial used is x8 + x2 + x + 1. The coset polynomial, x6 + x4 + x2 + 1, is added (modulo 2) to the residue. The calculated HEC is then inserted into the byte immediately following the header. HEC coset polynomial addition is programmable. If the cell received from the Transmit FIFO contains a HEC byte, the received HEC byte can be passed through or overwritten with the calculated HEC byte. HEC byte pass through is programmable. If the cell received from the Transmit FIFO does not contain a HEC byte, the calculated HEC byte is inserted into the cell. If cell processing is disabled, HEC processing will not be performed. Cell error insertion inserts errors into the HEC byte. The HEC bits to be errored are programmable. Error insertion can be controlled by a register or by the manual error insertion input (TMEI). The error insertion initiation type (register or input) is programmable. If a register controls error insertion, the number and frequency of the errors are programmable. If cell processing is disabled, cell error insertion will not be performed. Cell scrambling can scramble the 48-byte cell payload, scramble the entire cell data stream, or scramble the data stream with a Distributed Sample Scrambler (DSS). If the payload or the entire data stream is scrambled, a selfsynchronous scrambler with a generation polynomial of x43 + 1 is used. For payload scrambling, the scrambler scrambles the 48-byte payload, and does not scramble the four header or the HEC bytes. For a DSS scrambled data stream, a distributed sample scrambler with a generation polynomial of x31 + x28 + 1 is used for scrambling. The transmit DSS scrambler scrambles the 48-byte payload and the four byte header. Scrambles the first HEC bit (HEC[1]) with the first transmit DSS scrambler sample (the transmit DSS scrambler bit from 211 bits earlier), scrambles the second HEC bit (HEC[2]) with the second transmit DSS scrambler sample (the current transmit DSS scrambler bit), and. Does not scramble the remaining HEC bits (HEC[3:8]). DSS scrambling can only be performed 141 DS3181/DS3182/DS3183/DS3184 in bit synchronous mode. Cell scrambling is programmable (payload, entire data stream, or DSS). If cell processing is disabled, the entire data stream will be scrambled whenever scrambling is enabled Once all cell processing has been completed, in bit synchronous mode, the 8-bit parallel data stream is multiplexed into a serial data stream and passed on. In octet aligned mode, the 8-bit parallel data stream is passed on. 10.7.5.2 Receive Cell Processor The Receive Cell Processor performs cell descrambling, cell delineation, cell filtering, header pattern comparison, OCD detection, HEC error monitoring, HEC byte filtering, and bit reordering. The data coming in can be either a serial data stream (bit synchronous mode) or an 8-bit parallel data stream (octet aligned mode). The type of data stream received affects cell descrambling and cell delineation, however, it does not affect OCD detection, HEC error monitoring, cell filtering, header pattern comparison, HEC byte filtering, or bit reordering. Cell processing can be disabled (clear-channel enable). Disabling cell processing disables cell delineation, OCD detection, cell filtering, header pattern comparison, HEC error monitoring, and HEC byte filtering. Only cell descrambling and bit reordering are not disabled. Cell descrambling can descramble the 48-byte cell payload, descramble the entire cell data stream, or descramble a data stream scrambled by a Distributed Sample Scrambler (DSS). If the payload or the entire data stream is descrambled, a self-synchronous scrambler with a generation polynomial of x43 + 1 is used for descrambling. Payload descrambling descrambles the 48-byte payload, and does not descramble the four header bytes or the HEC byte. For a DSS scrambled data stream, a distributed sample scrambler with a generation polynomial of x31 + x28 + 1 is used for descrambling. The receive DSS scrambler is synchronized to the transmit DSS scrambler by DSS scrambler synchronization. DSS descrambling can only be performed in bit synchronous mode. Cell descrambling is programmable (payload, entire data stream, or DSS). In bit synchronous mode, descrambling is performed one bit at a time, and the serial data stream is demultiplexed in to an 8-bit data stream before being passed on. In octet aligned mode, descrambling is performed 8-bits at a time, and only payload or entire data stream descrambling can be performed. When cell processing is disabled, the entire data stream will be descrambled if descrambling is enabled. DSS Scrambler Synchronization synchronizes the receive DSS scrambler with the transmit DSS scrambler used to scramble the incoming data stream. The DSS Scrambler Synchronization state machine has three states: "Acquisition", "Verification", and "Steady State". The "Acquisition" state adds the transmit DSS scrambler samples from 16 incoming cells into the receive DSS scrambler (32 samples total). The samples are derived from the two MSBs (HEC[1:2]) of the incoming HEC byte. Each time the samples in a cell are loaded into the receive DSS scrambler, the confidence counter is incremented. When the confidence counter reaches 16, DSS scrambler synchronization transitions to the "Verification" state. The "Verification" state verifies the samples in the incoming cells by comparing the samples from the cell with the corresponding receive DSS scrambler bits. Each time both samples from a cell match the corresponding receive DSS scrambler bits, the confidence counter is incremented. Each time one of the samples from a cell does not match the corresponding receive DSS scrambler bit, the confidence counter is decremented if the confidence counter reaches 24, DSS scrambler synchronization transitions to the "Steady State" state. If the confidence counter reaches 8, DSS scrambler synchronization transitions to the "Acquisition" state. The "Steady State" state continues to verify the samples in the incoming cells. Each time both samples from a cell match the corresponding receive DSS scrambler bits, the confidence counter is incremented (maximum count = 24). Each time one of the samples from a cell does not match the corresponding receive DSS scrambler bit, the confidence counter is decremented. If the confidence counter reaches 16, DSS scrambler synchronization transitions to the "Acquisition" state. The DSS scrambler synchronization state diagram is shown in Figure 10-26. DSS scrambler synchronization starts in the "Acquisition" state. Note: All ATM cells are discarded during the "Acquisition" and "Verification" states. 142 DS3181/DS3182/DS3183/DS3184 Figure 10-26. Receive DSS Scrambler Synchronization State Diagram 8C Pas ell s n 8C io cat rifi Ve ail sV sF ell eri fic atio n Steady State 8 Cells Fail Verification Verification Acquisition 32 Samples Loaded If cell processing is disabled, a cell boundary is arbitrarily chosen, and the data is divided into "cells" whose size is programmable. If HEC transfer is enabled in the receive system interface, the incoming data stream will be divided into 53-byte "cells". If HEC transfer is disabled in the receive system interface, the data is divided into 52-byte "cells". These cells are then passed on to bit reordering bypassing cell delineation, OCD detection, cell filtering, header pattern comparison, HEC error monitoring, and HEC byte filtering. Cell delineation determines the cell boundary by identifying the header bytes and the HEC byte of a cell, and detects an out of cell delineation (OCD) condition or a change of cell delineation (COCD). Cell delineation is performed off-line, and the data path cell boundary is only updated by cell delineation if an OCD condition is present. Performing cell delineation off-line results in fewer cells being discarded when the cell boundary changes. If DSS scrambling is enabled (bit synchronous mode only), only the six least significant bits (LSBs) of the HEC (HEC[3:8]) are used for cell delineation, as the two most significant bits (MSBs) are scrambled. An OCD condition is declared if seven consecutive cells are received with incorrect HEC bytes. An OCD condition is terminated if "Delta" consecutive cells are received with correct HEC bytes, if cell delineation updates the data path cell boundary, or if the PLCP framer updates the data path cell boundary (PLCP modes only). All ATM cells are discarded during an OCD condition. A COCD is declared when Cell Delineation or the PLCP framer updates the data path cell boundary with a cell boundary that is different from the current data path cell boundary . Cell delineation has three states: "Hunt", "Presync", and "Sync". The "Hunt" state searches for the cell boundary. Each time slot is checked for an HEC byte (six LSBs of the HEC byte if DSS is enabled). The cell boundary is set once the header and HEC bytes are identified, and cell delineation transitions to the "Presync" state. The "Presync" state verifies the cell boundary identified in the "Hunt" state. The HEC is checked in each incoming cell. If "Delta" cells (including the "Hunt" to "Presync" transition cell) with a correct HEC are received, cell delineation transitions to the "Sync" state. If a cell with an incorrect HEC is received, cell delineation transitions to the "Hunt" state. The "Sync" state checks the HEC in each cell. If a cell with a correct HEC is received, cell delineation updates the data path cell boundary if an OCD condition is present. If a cell with an incorrect HEC is received, cell delineation transitions to the "Hunt" state. The cell delineation state diagram is shown in Figure 10-27. The cell delineation process starts in the "Hunt" state. In octet-aligned mode, the HEC check is performed one byte at a time, so up to 53 checks may be needed to find the cell boundary. In bit synchronous mode, the HEC check is performed one bit at a time, so up to 424 checks may be needed to find the cell boundary. HEC calculation coset polynomial addition can be disabled. The cell delineation process can be programmed to ignore the first header byte (for DQDB applications) when calculating the HEC. If cell processing is disabled, cell delineation will not be performed. A "Delta" of eight is used during the DS3 clear-channel, STS-1 clear-channel, and E3 clear-channel modes. A "Delta" 143 DS3181/DS3182/DS3183/DS3184 of six is used during all other modes including the DS3 Clear-Channel--OHM; STS-1 Clear-Channel--OHM; and E3 Clear-Channel--OHM modes. In bit synchronous mode, the serial data stream is demultiplexed into an 8-bit parallel data stream (as determined by the data path cell boundary updated) before being passed on to cell filtering. Figure 10-27. Cell Delineation State Diagram De lta Co C HE ect orr Inc rre ct H EC s Sync Incorrect HEC Presync Hunt Correct HEC Cell filtering discards specific cell types. The 8-bit parallel data stream is monitored for idle, unassigned, and invalid cells. (Cells discarded during cell delineation or DSS descrambling are not monitored for cell filtering.) If cell filtering is enabled and the indicated cell type is found, the cell is discarded. Idle cell, unassigned cell, and invalid cell filtering are programmable. Idle cells have a header value of 00000000 00000000 00000000 00000001. Unassigned cells have a header value of xxxx0000 00000000 00000000 0000xxx0. Where x can be any value. Invalid cells have a header value of xxxxyyyy yyyy0000 00000000 0000xxxx. Where x can be any value and yyyyyyyy can be any value other than 00000000. All cells discarded are counted. If cell processing is disabled, cell filtering will not be performed. Header pattern comparison checks for a specific pattern in the header, and either discards and counts cells with a matching header (discard match), discards and counts cells without a matching header (discard no match), counts cells with a matching header (count match), or counts cells without a matching header (count no match). (Cells discarded during OCD detection, DSS descrambling, or cell filtering processes are not monitored for header pattern comparison.) The 8-bit parallel data stream is monitored for cells that have a header that matches the comparison header. In discard match mode, cells with a matching header are counted and discarded. In discard no match mode, cells without a matching header are counted and discarded. In count match mode, cells with a matching header are counted and passed on. In count no match mode, cells without a matching header are counted and passed on. The comparison header and comparison header pattern mode are programmable. If cell processing is disabled, header pattern comparison will not be performed. HEC error monitoring checks the HEC and detects errored and correctable cell headers. (Cells discarded during OCD detection, DSS descrambling, cell filtering, or header pattern comparisons are not monitored for HEC errors.). HEC Error Monitoring has two states, the "Correction" and "Detection" states. . In the "Correction" state, cells received without any header errors (good cells) are passed on. Cells received with a single header error (correctable cells) are corrected and passed on. The corrected cell count is incremented. Cells received with multiple errors are considered errored cells. If errored cell extraction is enabled, errored cells are discarded, and the errored cell count is incremented. If errored cell extraction is disabled, errored cells are passed on. If a cell is 144 DS3181/DS3182/DS3183/DS3184 received with an incorrect HEC, HEC error monitoring transitions to the "Detection" state. In the "Detection" state, good cells are passed on. Cells received with one or more errors are considered errored cells. If m cells are received with a correct HEC or the data path cell boundary is updated, HEC error monitoring will transition to the "Correction" state. The value of m is programmable (1, 2, 4, or 8). The HEC Error Monitoring state diagram is shown in Figure 10-28. HEC Error Monitoring starts in the "Correction" state. If header error correction is disabled, HEC error monitoring will remain in the "Detection" state. If cell processing is disabled, HEC error monitoring will not be performed. Figure 10-28. HEC Error Monitoring State Diagram corrected cell m th good cell C orrection D etection cell boundary update errored cell HEC byte filtering discards the HEC byte. If HEC transfer is disabled in the receive system interface, the HEC byte is extracted from the cell and discarded. The resulting 52-byte cell is then passed on for storage in the Receive FIFO. If HEC transfer is enabled, the 53-byte cell is passed on for storage in the Receive FIFO. If cell processing is disabled, HEC byte filtering will not be performed. Bit reordering changes the bit order of each byte. If bit reordering is enabled, the incoming 8-bit data stream DT[7:0] with DT[7] being the MSB and DT[0] being the LSB is rearranged so that the MSB is in DT[0] and the LSB is in DT[7] of the outgoing FIFO data stream DT[7:0]. In bit synchronous mode, DT[7] is the first bit received. Once all cell processing has been completed, the 8-bit parallel data stream is demultiplexed into a 32-bit parallel data stream and passed on to the Receive FIFO. Cells are stored in the Receive FIFO in a cell format. regardless of whether or not they are transferred across a UTOPIA or POS-PHY interface. The cell format for a 53-byte cell with a 32-bit bus is shown in Figure 10-29. The cell format for a 52-byte cell with a 32-bit bus is shown in Figure 10-30. Figure 10-29. Cell Format for 53-Byte Cell With 32-Bit Data Bus Bit 31 Bit 0 Header 1 Header 2 Header 3 Header 4 1st Transfer HEC 00h 00h 00h 2nd Transfer Payload 1 Payload 2 Payload 3 Payload 4 3rd Transfer Payload 5 Payload 6 Payload 7 Payload 8 4th Transfer * * * * * * * * * * * * Payload 41 Payload 42 Payload 43 Payload 44 13th Transfer Payload 45 Payload 46 Payload 47 Payload 48 14th Transfer 145 DS3181/DS3182/DS3183/DS3184 Figure 10-30. Cell Format for 52-Byte Cell With 32-Bit Data Bus Bit 31 Bit 0 Header 1 Header 2 Header 3 Header 4 1st Transfer Payload 1 Payload 2 Payload 3 Payload 4 2nd Transfer Payload 5 Payload 6 Payload 7 Payload 8 3rd Transfer * * * * * * * * * * * * Payload 41 Payload 42 Payload 43 Payload 44 12th Transfer Payload 45 Payload 46 Payload 47 Payload 48 13th Transfer 10.7.6 Packet Processor 10.7.6.1 Transmit Packet Processor The Transmit Packet Processor accepts data from the Transmit FIFO performs bit reordering, FCS processing, packet error insertion, stuffing, packet abort sequence insertion, inter-frame padding, and packet scrambling. The data output from the Transmit Packet Processor can be either a serial data stream (bit synchronous mode) or an 8bit parallel data stream (octet-aligned mode). The type of data stream output from the Transmit Packet Processor affects stuffing, abort insertion, inter-octet padding, inter-frame padding, and packet scrambling, however, it does not affect bit reordering, FCS processing, or packet error insertion. Packet processing can be disabled (clearchannel enable). Disabling packet processing disables FCS processing, packet error insertion, stuffing, packet abort sequence insertion, and inter-frame padding. Only bit reordering and packet scrambling are not disabled. When packet processing is disabled, data is continually read out of the Transmit FIFO. When the Transmit FIFO is read empty, the output data stream will be padded with FFh until the Transmit FIFO contains more data than the "almost empty" level. The 32-bit data words read from the Transmit FIFO are multiplexed into an 8-bit parallel data stream and passed on to bit reordering. Bit reordering changes the bit order of each byte. If bit reordering is enabled, the incoming 8-bit data stream DT[7:0] with DT[7] being the MSB and DT[0] being the LSB is rearranged so that the MSB is in DT[0] and the LSB is in DT[7] of the outgoing data stream DT[7:0]. In bit synchronous mode, DT[7] is the first bit transmitted. If packet processing is disabled the data stream is passed on to packet scrambling, bypassing FCS processing, packet error insertion, stuffing, packet abort sequence insertion, and inter-frame padding. If packet processing is disabled in bit synchronous mode, the serial data stream is demultiplexed in to an 8-bit data stream before being passed on. FCS processing calculates a FCS and appends it to the packet. FCS calculation is a CRC-16 or CRC-32 calculation over the entire packet. The polynomial used for FCS-16 is x16 + x12 + x5 + 1. The polynomial used for FCS-32 is x32 + x26 + x23 + x22 + x16 + x12 + x11 + x10 + x8 + x7 + x5 + x4 + x2 + x + 1. The FCS is inverted after calculation. The FCS type is programmable. If FCS append is enabled, the calculated FCS is appended to the packet. If FCS append is disabled, the packet is transmitted without a FCS. The FCS append mode is programmable. If packet processing is disabled, FCS processing is not performed. Packet error insertion inserts errors into the FCS bytes. A single FCS bit is corrupted in each errored packet. The FCS bit corrupted is changed from errored packet to errored packet. Error insertion can be controlled by a register or by the manual error insertion input (TMEI). The error insertion initiation type (register or input) is programmable. If a register controls error insertion, the number and frequency of the errors are programmable. If FCS append is disabled, packet error insertion will not be performed. If packet processing is disabled, packet error insertion is not performed. Stuffing inserts control data into the packet to prevent packet data from mimicking flags. Stuffing is performed from the beginning of a packet until the end of a packet. In bit synchronous mode, the 8-bit parallel data stream is multiplexed into a serial data stream, and bit stuffing is performed. Bit stuffing consists of inserting a '0' directly following any five contiguous '1's. In octet aligned mode, byte stuffing is performed. Byte stuffing consists of detecting bytes that mimic flag and escape sequence bytes (7Eh and 7Dh), and replacing the mimic bytes with an escape sequence (7Dh) followed by the mimic byte exclusive ORed with 20h. If packet processing is disabled, stuffing is not performed. 146 DS3181/DS3182/DS3183/DS3184 Inter-frame padding inserts start flags, end flags and inter-frame fill between packets. There will be at least one flag plus a programmable number of additional flags between packets. In octet aligned mode, the inter-frame fill is flags. In bit synchronous mode, the inter-frame fill can be flags or all 1s followed by a start flag. If the inter-frame fill is all '1's, the number of '1's between the end and start flags may not be an integer number of bytes, however, there will be at least 15 consecutive '1's between the end and start flags. The bit synchronous mode inter-frame padding type is programmable. If packet processing is disabled, inter-frame padding is not performed. Packet abort insertion inserts a packet abort sequences as necessary. If a packet abort indication is detected, a packet abort sequence is inserted and inter-frame padding is done until a packet start flag is detected. In bit synchronous mode, the abort sequence is FFh. In octet aligned mode, the abort sequence is 7D7Eh. If packet processing is disabled, packet abort insertion is not performed. The packet scrambler is a x43 + 1 self-synchronous scrambler that scrambles the entire packet data stream. Packet scrambling is programmable. Once all packet processing has been completed, in bit synchronous mode, the 8-bit parallel data stream is multiplexed into a serial data stream and passed on. In octet aligned mode, the 8-bit parallel data stream is passed on. 10.7.6.2 Receive Packet Processor The Receive Packet Processor performs packet descrambling, packet delineation, inter-frame fill filtering, packet abort detection, destuffing, packet size checking, FCS error monitoring, FCS byte extraction, and bit reordering. The data coming in can be either a serial data stream or an 8-bit parallel data stream, depending on the framing mode (see Table 10-32 for configuration information). The type of data stream received affects packet descrambling, packet delineation, inter-frame fill filtering, packet abort detection, and destuffing, however, it does not affect packet size checking, FCS error monitoring, FCS byte extraction, or bit reordering. Packet processing can be disabled (clear-channel enable). Disabling packet processing disables packet delineation, inter-frame fill filtering, packet abort detection, destuffing, packet size checking, FCS error monitoring, and FCS byte extraction. Only packet descrambling and bit reordering are not disabled. The packet descrambler is a self-synchronous x43 + 1 descrambler that descrambles the entire packet data stream. Packet descrambling is programmable. If packet processing is disabled in bit synchronous mode, the serial data stream is demultiplexed in to an 8-bit data stream before being passed on. If packet processing is disabled, a packet boundary is arbitrarily chosen, and the data is divided into "packets" whose size is programmable (maximum packet size setting). These packets are then passed on to bit reordering bypassing packet delineation, inter-frame fill filtering, packet abort detection, destuffing, packet size checking, FCS error monitoring, and FCS byte extraction. Packet delineation determines the packet boundary by identifying a packet start or end flag. Each time slot is checked for a flag sequence (7Eh). Once a flag is found, it is identified as a start or end flag, and the packet boundary is set. If packet processing is disabled, packet delineation is not performed. Inter-frame fill filtering removes the inter-frame fill between packets. When a packet end flag is detected, all data is discarded until a packet start flag is detected. In bit synchronous mode, the inter-frame fill can be flags or all '1's. When the interframe fill is all `1's, the number of '1's between the start and end flags does not need to be an integer number of bytes. In bit synchronous mode when inter-frame fill is flags, there may be only one flag between packets, or the flags may have a shared zero (011111101111110). In octet aligned mode, the inter-frame fill can only be flags, and there may be only one flag between packets. If packet processing is disabled, inter-frame fill filtering is not performed. Packet abort detection searches for a packet abort sequence. Between a packet start flag and a packet end flag, if an abort sequence is detected, the packet is marked with an abort indication, the aborted packet count is incremented, and all subsequent data is discarded until a packet start flag is detected. In bit synchronous mode, the abort sequence is seven consecutive ones. In octet aligned mode, the abort sequence is 7D7Eh. If packet processing is disabled, packet abort detection is not performed. Destuffing removes the extra data inserted to prevent data from mimicking a flag or an abort sequence. In bit synchronous mode, bit destuffing is performed. Bit destuffing consists of discarding any '0' that directly follows five contiguous '1's. In octet aligned mode, byte destuffing is performed. Byte destuffing consists of detecting an escape sequence (7Dh), discarding it and exclusive ORing the next byte with 20h. In bit synchronous mode, after destuffing is completed, the serial bit stream is demultiplexed into an 8-bit parallel data stream and passed on to packet size checking. If there is less than eight bits in the last byte, an invalid packet flag is raised, the packet is 147 DS3181/DS3182/DS3183/DS3184 tagged with an abort indication, and the packet size violation count is incremented. In octet aligned mode, after destuffing is completed, the 8-bit parallel data stream is passed on to packet size checking. If packet processing is disabled, destuffing is not performed. Packet size checking checks each packet for a programmable maximum and programmable minimum size. As the packet data comes in, the total number of bytes is counted. If the packet length is below the minimum size limit, the packet is marked with an aborted indication, and the packet size violation count is incremented. If the packet length is above the maximum size limit, the packet is marked with an aborted indication, the packet size violation count is incremented, and all packet data is discarded until a packet start is received. The minimum and maximum lengths include the FCS bytes, and are determined after destuffing has occurred. If packet processing is disabled, packet size checking is not performed. FCS error monitoring checks the FCS and aborts errored packets. If a FCS error is detected, the FCS errored packet count is incremented and the packet is marked with an aborted indication. The FCS type (16-bit or 32-bit) is programmable. If FCS processing or packet processing is disabled, FCS byte extraction is not performed. FCS byte extraction discards the FCS bytes. If FCS extraction is enabled, the FCS bytes are extracted from the packet and discarded. If FCS extraction is disabled, the FCS bytes are stored in the receive FIFO with the packet. If FCS processing or packet processing is disabled, FCS byte extraction is not performed. Bit reordering changes the bit order of each byte. If bit reordering is enabled, the incoming 8-bit data stream DT[7:0] with DT[7] being the MSB and DT[0] being the LSB is rearranged so that the MSB is in DT[0] and the LSB is in DT[7] of the outgoing FIFO data stream DT[7:0]. In bit synchronous mode, DT[7] is the first bit received. Once all packet processing has been completed, the 8-bit parallel data stream is demultiplexed into a 32-bit parallel data stream and passed on to the Receive FIFO. 10.7.7 FIFO 10.7.7.1 Transmit FIFO The Transmit FIFO block contains memory for 64 32-bit data words. The Transmit FIFO separates the transmit system interface timing from the transmit physical interface timing. The Transmit FIFO functions include filling the memory, tracking the memory fill level, maintaining the memory read and write pointers, and detecting memory overflow and underflow conditions. The number of data transfers that can occur after the Transmit FIFO "full" indication is deasserted is programmable. The Transmit FIFO port address used for selection and polling by the Transmit System Interface Bus Controller is programmable. In system loopback, the data from the Transmit FIFO is looped back to the Receive FIFO, and a FIFO empty indication is passed on to the Transmit Cell/Packet Processor. In cell processing mode, all operations are cell based. The Transmit FIFO is considered empty when it does not contain any data. The Transmit FIFO is considered "almost empty" when it does not contain a cell. The Transmit FIFO is considered "almost full" when it does not have space available to store a programmable number of cells. The Transmit FIFO is considered full when it does not have space available for a complete cell. When the Transmit FIFO level drops below the "almost full" indication, the TDXA[n] is asserted. The Transmit FIFO accepts cell transfers from the Transmit System Interface Bus Controller until it is full. If a start of cell is received while full, the cell is discarded and a FIFO overflow condition is declared. Once a FIFO overflow condition is declared, the Transmit FIFO will discard cell data until a start of cell is received while the FIFO has more space available than the "almost full" level. If the Transmit FIFO receives cell data other than a start of cell after a complete cell has been received, an invalid transfer is declared and all cell data is discarded until a start of cell is received. If a start of cell is received before a previous cell transfer has been completed, the current cell is discarded and a short transfer is declared. The new cell is processed normally. If the Transmit Cell Processor attempts a read while the Transmit FIFO is empty, a FIFO underflow condition is declared. Once a FIFO underflow condition is declared, the Transmit FIFO data will be discarded until a start of cell is received. In packet processing mode, all operations are byte based. The Transmit FIFO is considered empty when its memory does not contain any data. The Transmit FIFO is considered "almost empty" when its memory does not contain a packet end and there is a programmable number of bytes or less stored in the memory. The Transmit FIFO is considered "almost full" when its memory has a programmable number of bytes or less available for storage. When the Transmit FIFO has more bytes available for storage than the "almost full" level the TDXA[n] or TPXA pin will be asserted to signal to the POS device that it is ready to receive more packet data. The Transmit FIFO is considered full when it does not have any space available for storage. When the Transmit FIFO is full, the TDXA[n] pin will be deasserted. The Transmit FIFO accepts data from the Transmit System Interface Bus Controller until full. If a start of packet or short packet (32-bit data word with a start of packet and end of packet) is 148 DS3181/DS3182/DS3183/DS3184 received while full, the data is discarded and a FIFO overflow condition is declared. If any other packet data is received while full, the current packet being transferred is marked with an abort indication, and a FIFO overflow condition is declared. Once a FIFO overflow condition is declared, the Transmit FIFO will discard data until a start of packet is received while the FIFO has more space available than the "almost full" level. If a packet error (a transfer with TERR and TEOP asserted) is received from the Transmit System Interface Bus Controller, an aborted transfer is declared, the data is stored in memory with a packet abort indication, and the Transmit FIFO will discard data until a start of packet is received. If an end of a packet has been received and the Transmit FIFO receives packet data other than a start of packet, an invalid transfer is declared, and all packet data is discarded until a start of packet is received. If a start of packet is received before a previous packet transfer has been completed (an end of packet was never received), the current packet being transferred is marked with an abort indication and a short transfer is declared. The new packet is processed normally. If the Transmit Packet Processor attempts a read while the Transmit FIFO is empty, a FIFO underflow condition is declared. Once a FIFO underflow condition is declared, the Transmit FIFO data will be discarded until a start of cell is received. 10.7.7.2 Receive FIFO The Receive FIFO block contains memory for 64 32-bit data words. The Receive FIFO separates the receive system interface timing from the receive physical interface timing. The Receive FIFO functions include filling the memory, tracking the memory fill level, maintaining the memory read and write pointers, and detecting memory overflow and underflow conditions. The Receive FIFO port address used for selection and polling by the Receive System Interface Bus Controller is programmable. In system loopback, data is looped back from the Transmit FIFO to the Receive FIFO. In cell processing mode, all operations are cell based. The Receive FIFO is considered empty unless it contains a cell. The Receive FIFO is considered "almost empty" when it contains a programmable number of cells or less. When the Receive FIFO level has more data available for transfer than the "almost empty" level, the RDXA[n] pin is asserted. The Receive FIFO is considered "almost full" when it does not have space available to store a complete cell. The Receive FIFO is considered full when it does not have any space available. The Receive FIFO accepts cell data from the Receive Cell Processor until full. If cell data is received while the FIFO is full, the cell is discarded and a FIFO overflow condition is declared. Once a FIFO overflow condition is declared, the Receive FIFO will discard cell data until a cell start is received while the FIFO has space available to store a complete cell. If the Receive System Interface Bus Controller attempts a read while the FIFO is empty, the read is ignored. In packet processing mode, all operations are 32-bit word based. The Receive FIFO is considered empty when it does not contain any data. The Receive FIFO is considered "almost empty" when its memory does not contain a packet end and there is a programmable number of words or less stored in the memory. When the Receive FIFO has more bytes available for transfer than the "almost empty" level or has an end of packet, the RDXA[n] pin is asserted (POS-PHY Level 2). The Receive FIFO is considered "almost full" when its memory has a programmable number of words or less available for storage. The Receive FIFO is considered full when it does not have any space available for storage. The Receive FIFO accepts data from the Receive Packet Processor until full. If a packet start or short packet is received while full, the data is discarded and a FIFO overflow condition is declared. If any other packet data (packet end or middle) is received while full, the current packet being received is marked with an abort indication, and a memory overflow condition is declared. Once a memory overflow condition is declared, the Receive FIFO will discard data until a packet start is received while the FIFO has more space available than the "almost full" level. If the Receive System Interface Bus Controller attempts a read while the FIFO is empty, the read is ignored. 10.7.8 System Loopback There is a system loopback available in the ATM/HDLC Mapper. The loopback can be performed on a per-port basis. When a port is placed in system loopback, the data coming in from the System Interface is looped back from the Transmit FIFO to the Receive FIFO, a FIFO empty indication is passed on to the Transmit Cell/Packet Processor, and all data coming from the Receive Cell/Packet Processor is discarded. The maximum throughput of a single port is limited to half of the Receive System Interface bandwidth in 32-bit mode. A loss of data may occur if the Receive System Interface clock (RSCLK) has a frequency that is greater than one and one half times the Transmit System Interface clock (TSCLK). 149 DS3181/DS3182/DS3183/DS3184 10.8 DS3/E3 PLCP Framer 10.8.1 General Description The PLCP Framer demaps the ATM cells from the DS3/E3 PLCP data stream in the receive direction and maps ATM cells into the DS3/E3 PLCP data stream in the transmit direction. The receive direction extracts the PLCP frame from the DS3/E3 data stream, performs frame processing, and outputs the cells with a beginning of cell indication via the payload interface. The transmit direction inputs the cells via the payload interface, generates the frame, and inserts the PLCP frame into the DS3/E3 data stream. See Figure 10-31 for the location of the PLCP framer in the DS318x devices. Figure 10-31. PLCP Framer Functional Diagram TAIS TUA1 Clock Rate Adapter B3ZS/ HDB3 Decoder IEEE P1149.1 JTAG Test Access Port Tx Packet Processor TX BERT HDLC DS3 / E3 Receive Framer RX BERT RX FRAC/ PLCP UA1 GEN Tx FIFO System Interface Trail Trace Buf f er PLB FEAC TX FRAC/ PLCP Tx Cell Processor SLB DLB LLB ALB DS3/E3 Transmit LIU DS3/E3 Receive LIU DS3 / E3 Transmit Formatter B3ZS/ HDB3 Encoder Rx Packet Processor Rx Cell Processor Rx FIFO Microprocessor Interface 10.8.2 Features * * * * * * * DS3 PLCP frame ATM cell extraction and insertion - Accepts a DS3 payload and performs DS3 PLCP overhead termination and generation. E3 PLCP frame ATM cell extraction and insertion - Accepts a G.751 E3 payload and performs E3 PLCP overhead termination and generation. Generates and detects alarms and errors - In the receive direction, PLCP alarm conditions (OOF, LOF, COFA, and RAI) and errors (framing, parity, and REI) are detected on the receive signal. In the transmit direction, alarm conditions and errors can be inserted into the transmit data stream. Receive overhead extraction port - Extracts all PLCP overhead from the receive signal and outputs it on a serial interface (RPOH pin). Externally controlled transmit overhead insertion port - Can insert all PLCP overhead into the transmit signal from a serial interface. Overhead insertion is fully controlled via the serial overhead interface (TPOH, TPOHEN, TPOHSOF, TPOHCLK). Full Duplex serial HDLC channel extraction/insertion - An HDLC channel can be extracted from and/or inserted into the F1, M1, M2, or M1 and M2 bytes in the PLCP data stream. Full Duplex serial Trail Trace extraction/insertion - A trail trace can be extracted from and/or inserted into the F1 byte in the PLCP data stream. 150 DS3181/DS3182/DS3183/DS3184 10.8.3 Transmit PLCP Frame Processor The Transmit PLCP Frame Processor receives the ATM cells from the ATM/Packet Processor performs trailer generation, framing generation, error insertion, and overhead insertion. The bits in a byte are transmitted MSB first, LSB last. When they are input serially, they are input in the order they are to be transmitted. The bits in a byte in an outgoing signal are numbered in the order they are transmitted, 1 (MSB) to 8 (LSB). However, when a byte is stored in a register, the MSB is stored in the highest numbered bit (7), and the LSB is stored in the lowest numbered bit (0). This is to differentiate between a byte in a register and the corresponding byte in a signal. 10.8.4 Receive PLCP Frame Processor The Receive PLCP Frame Processor accepts the data stream from the DS3/E3 Framer and extracts the entire DS3/E3 overhead and processes only the PLCP frame data. The bits in a byte are received MSB first, LSB last. When they are output serially, they are output in the order they are received. The bits in a byte in an incoming signal are numbered in the order they are received, 1 (MSB) to 8 (LSB). However, when a byte is stored in a register, the MSB is stored in the highest numbered bit (7), and the LSB is stored in the lowest numbered bit (0). This is to differentiate between a byte in a register and the corresponding byte in a signal. Some bits, bit groups, or bytes (data) are integrated. Integration requires the data to have a new value for five consecutive occurrences before the new data value will be stored in the data register. Integrated data may have an associated unstable indication. Integrated data is considered unstable if for eight consecutive occurrences the received data value does not match the currently stored (integrated) data value or the previously received data value. 10.8.5 Transmit DS3 PLCP Frame Processor The DS3 PLCP frame format is shown in Figure 10-32. A1 and A2 are the sub-frame alignment bytes that have a value of F6h and 28h respectively. P11 - P0 are the Path Overhead Identifier (POI) bytes that indicate the path overhead byte contained in the current sub-frame. Z6 - Z1 are growth bytes reserved for future use. F1 is the Path User Channel byte allocated for user communications purposes (This byte is undefined in ATM). B1 is the Bit Interleaved Parity-8 (BIP-8) byte used for PLCP path error monitoring. G1 is the PLCP Path Status Byte (See Figure 10-33) used for far-end path status and performance monitoring (bits 6 - 8 are undefined in ATM). M2 and M1 are the DQDB Layer Management Information bytes used for DQDB layer management communications (These bytes are undefined in ATM). C1 is the Cycle/Stuff Counter byte used as for PLCP superframe alignment and stuff indication. 151 DS3181/DS3182/DS3183/DS3184 Figure 10-32. DS3 PLCP Frame Format A1 A2 P11 Z6 First Cell A1 A2 P10 Z5 Second Cell A1 A2 P9 Z4 Third Cell A1 A2 P8 Z3 Fourth Cell A1 A2 P7 Z2 Fifth Cell A1 A2 P6 Z1 Sixth Cell A1 A2 P5 F1 Seventh Cell A1 A2 P4 B1 Eight Cell A1 A2 P3 G1 Ninth Cell A1 A2 P2 M2 Tenth Cell A1 A2 P1 M1 Eleventh Cell A1 A2 P0 C1 Twelfth Cell Trailer Subframe (57 Bytes) 13 or 14 Nibbles 12 Subframes Figure 10-33. DS3 PLCP G1 Byte Format G1 MSB 1 REI REI REI REI LSB 8 RAI LSS LSS LSS REI - Remote Error Indicator RAI - Remote Alarm Indicator LSS - Link Status Signal 10.8.5.1 Transmit DS3 PLCP Trailer Generation DS3 PLCP trailer generation inserts the DS3 PLCP frame trailer immediately following sub-frame 0 (POI equals 01h), and generates the C1 byte. The trailer size is determined by the DS3 PLCP superframe counter, and the 8 kHz reference clock. The DS3 PLCP superframe counter is a free running counter that indicates the current frame of the three-frame superframe. In the first frame of the superframe, the trailer size is set to 13, and C1 is set to FFh. In the second frame of the superframe, the trailer size is set to 14, and C1 is set to 00h. In the third frame of the superframe, the trailer size is variable. The trailer size is controlled by the 8kHz reference clock. If the indicated trailer size is 13, C1 is set to 66h. If the indicated trailer size is 14, C1 is set to 99h, and the indicated number of nibbles (13 or 14) are added after sub-frame 0. The trailer nibbles are all set to 1100. 152 DS3181/DS3182/DS3183/DS3184 10.8.5.2 Transmit DS3 PLCP Frame Generation DS3 PLCP frame generator receives the incoming PLCP payload data stream, and overwrites all of the overhead byte locations. The first two bytes of each sub-frame are overwritten with the frame alignment bytes A1 and A2, which have a value of F6h and 28h respectively. The third byte of sub-frame # is overwritten with POI byte # (P#). The value of P# is 00####0Pb (0 = a logic zero, #### = the hexadecimal value of #, and P = the odd parity bit). The fourth byte of sub-frames #11 - 6 are overwritten with the Z6 - Z1 bytes from the corresponding registers. The fourth byte of sub-frame 5 is overwritten with the F1 byte from the corresponding register, the trail trace byte input from the transmit trail trace controller, or the HDLC Overhead Processor. The F1 byte source is programmable PLCP.TCR.TF1C[1:0] (trail trace controller, HDLC, or register). The fourth byte of sub-frame 4 is overwritten with the calculated BIP-8. The BIP-8 is calculated over all of the path overhead bytes and cell bytes of the previous frame after all PLCP processing (frame generation, error insertion, and overhead insertion) has been completed. The first four bits of the fourth byte of sub-frame 3 are overwritten with the G1 byte REI bits (G1[1:4]). The Remote Error Indication (REI) bits can be generated automatically or inserted from the G1 register bits. The REI source is programmable (auto or register). If the REI bits are generated automatically, they are set to zero when the receive side B1 byte exactly matches the BIP-8 calculated for the previous receives side frame. Otherwise, the REI is set to a value of one to eight to indicate the number of parity errors (BIP-8 errors) detected in the receive PLCP frame (B1 byte). The fifth bit of the fourth byte of sub-frame 3 is overwritten with the G1 byte RAI bit (G1[5]). The Remote Alarm Indication (RAI) bit is sourced from a register. The last three bits of the fourth byte of sub-frame 3 are overwritten with the G1 byte LSS bits (G1[6:8]). The Link Status Signal (LSS) bits are sourced from a register. The three register bits are inserted in the sixth, seventh, and eighth bits of the G1 byte in each frame. The fourth byte of sub-frames 2 and 1 are overwritten with the M2 and M1 bytes respectively. Each byte can be individually sourced from a register, or from the transmit HDLC controller. The M2 byte and M1 byte sources are each programmable (register or HDLC). If both bytes are programmed to be sourced from the transmit HDLC controller, they are concatenated as a single data link as opposed to two separate data links. The fourth byte of sub-frame 0 is overwritten with the C1 byte created during trailer generation. Once all of the overhead bytes have been overwritten, the data stream is passed on to error insertion. 10.8.5.3 Transmit DS3 PLCP Error Insertion Error insertion inserts various types of errors into the different overhead bytes. The types of errors that can be inserted are framing errors, BIP-8 parity errors, and Remote Error Indication (REI) errors. The type of framing error(s) inserted is programmable (frame bit error or framing byte error). A framing bit error is a single bit error in a frame alignment byte (A1 or A2) or POI byte (P#). A framing byte error is an error in all eight bits of a frame alignment byte (A1 or A2) or path overhead indicator (POI) byte (P#). Framing error(s) can be inserted one error at a time, or in two consecutive bytes (A1 & A2 or P# & P#+1). The framing error insertion rate (single A1 or A2, single P#, A1 & A2, or P# & P#+1) is programmable. The type of BIP-8 error(s) inserted is programmable (errored BIP-8 bit or errored BIP-8 byte). An errored BIP-8 bit is inverting a single bit error in the B1 byte. An errored BIP-8 byte is inverting all eight bits in the B1 byte. BIP-8 error(s) can be inserted one error at a time, or continuously. The BIP-8 error insertion rate (single or continuous) is programmable. The type of REI error(s) inserted is programmable (single REI error or eight REI errors). A single REI error is generated by setting the first four bits of the G1 byte to a value of 1h. Eight REI errors are generated by setting the first four bits of the G1 byte to a value of 8h. REI error(s) can be inserted one error at a time, or continuously. The REI error insertion rate (single or continuous) is programmable. 153 DS3181/DS3182/DS3183/DS3184 Error insertion can be initiated by a register bit (PLCP.TEIR.TSEI) or initiated by the manual error insertion input (TMEI). Each error type is individually enabled by a register bit. The error insertion initiation type (register or input) is programmable. Once all error insertion has been performed, the data stream is passed on to overhead insertion. 10.8.5.4 Transmit DS3 PLCP Overhead Insertion Overhead insertion can insert any (or all) of the path overhead bytes into the DS3 PLCP frame. The overhead bytes Z6 - Z1, F1, B1, G1, M1, M2, and C1 can be sourced from the transmit overhead interface (TPOHCLK, TPOH, TPOHEN, and TPOHSOF). The B1 and C1 bytes are sourced as error masks (modulo 2 addition of the input B1/C1 byte and the generated B1/C1 byte). The overhead insertion is fully controlled by the transmit overhead interface. If the transmit PLCP overhead data enable signal (TPOHEN) is driven high, then the bit on the transmit PLCP overhead signal (TPOH) is inserted into the output data stream. Insertion of bits using the TPOH signal overwrites internal overhead insertion. 10.8.6 Receive DS3 PLCP Frame Processor The DS3 PLCP frame format is shown in Figure 10-32. A1 and A2 are the sub-frame Alignment bytes that have a value of F6h and 28h respectively. P11 - P0 are the Path Overhead Identifier (POI) bytes that indicate the path overhead byte contained in the current sub-frame. Z6 - Z1 are growth bytes reserved for future use. F1 is the Path User Channel byte allocated for user communications purposes (This byte is undefined in ATM). B1 is the Bit Interleaved Parity-8 (BIP-8) byte used for PLCP path error monitoring. G1 is the PLCP Path Status Byte (See Figure 10-33) used for far-end path status and performance monitoring (bits 6 - 8 are undefined in ATM). M1 and M2 are the DQDB Layer Management Information bytes used for DQDB layer management communications (These bytes are undefined in ATM). C1 is the Cycle/Stuff Counter byte used as for PLCP superframe alignment and stuff indication. 10.8.6.1 Receive DS3 PLCP Framing DS3 PLCP framing determines the DS3 PLCP frame boundary. The frame boundary is found by identifying the frame alignment bytes (A1 & A2), and the path overhead indicator (POI) byte (P#). The framer is an off-line framer that updates the data path frame counters when an out of frame (OOF) condition is present. The use of an off-line framer reduces the number of ATM cells discarded during the framing process. The framer continually searches for two consecutive sets of alignment bytes (A1 and A2), and two sequential POI bytes (P#) are identified. The data path frame counters are updated if an OOF condition is present. The maximum average reframe time is 17 s. 10.8.6.2 Receive DS3 PLCP Nibble Destuffing Nibble destuffing discards the DS3 PLCP frame trailer immediately following sub-frame 0 (POI equals 01h). The trailer size is determined by the DS3 PLCP superframe counter, and the cycle counter byte (C1). The trailer is 13 nibbles in the first frame of the superframe (C1 equals FFh). The trailer is 14 nibbles in the second frame of the superframe (C1 equals 00h). The trailer length is variable in the third frame of the superframe. It is 14 nibbles if C1 equals 66h and 14 nibbles if C1 equals 99h. The superframe counter is updated immediately upon receiving an error free C1. In the third superframe, majority voting (5 of 8) is used to determine the trailer size. Once the trailer size has been determined, the trailer nibbles are discarded. 10.8.6.3 Receive DS3 PLCP Performance Monitoring Performance monitoring checks the DS3 PLCP frame for errors and alarm conditions. The alarm conditions detected are OOF, LOF, COFA, and RAI. All alarm conditions are defect conditions. The PLCP Framer does not integrate alarms for failure conditions. An Out Of Frame (OOF) condition is declared when two consecutive framing bytes (A1 and A2) or two consecutive POI bytes (P0 - P11) are erred. An OOF condition is terminated when two sequential POI bytes and two consecutive framing words (A1 and A2) are error free or the DS3 PLCP framer updates the data path frame counters. If the Loss Of Frame (LOF) integration counter is disabled, an LOF condition is declared when an OOF condition has been continuously present for 1 ms. If the LOF integration counter is enabled, an LOF condition is declared by the LOF integration counter when the counter has been active for a total of 1 ms. The LOF integration counter is active (increments count) when an OOF condition is present, it is inactive (holds count) when an OOF condition is absent, and it is reset when an OOF condition is continuously absent for 1 ms. An LOF condition is terminated when an OOF condition is continuously absent for 1 ms. 154 DS3181/DS3182/DS3183/DS3184 A Change Of Frame Alignment (COFA) is declared when the DS3 PLCP framer updates the data path frame counters with a frame alignment that is different from the current data path frame alignment. A Remote Alarm Indication (RAI) condition is declared when ten consecutive frames are received with the RAI bit (fifth bit of G1) set to one. An RAI condition is terminated when ten consecutive frames are received with the RAI bit set to zero. Three types of errors are accumulated, framing errors, BIP-8 errors and Remote Error Indication (REI) errors. Framing errors are determined by comparing A1, A2, and P# to their expected values. The type of framing errors accumulated is programmable (OOF, bit, byte, or word). An OOF error increments the count whenever an OOF condition is first detected (up to 1 per 3 sub-frames). A bit error increments the count once for each bit in A1, each bit in A2, and each bit in P# that does not match its expected value (up to 24 per sub-frame). A byte error increments the count once for each A1 byte, A2 byte, and P# byte that does not match its expected value (up to 3 per sub-frame). A word error increments the count once for each frame alignment word (A1, A2, and P#) that does not match its expected value (up to 1 per sub-frame). The detection of POI byte (P#) framing errors is programmable (on or off). BIP-8 errors are determined by calculating the BIP-8 of the current frame (path overhead and cell bytes), and comparing the calculated BIP-8 to the B1 byte in the next frame. The type of BIP-8 errors accumulated is programmable (bit or block). A bit error increments the count once for each bit in the B1 byte that does not match the corresponding bit in the calculated BIP-8 (up to 8 per frame). A block error increments the count if any bit in the B1 byte does not match the corresponding bit in the calculated BIP-8 (up to 1 per frame). REI errors are determined by the four REI bits (first four bits of G1). The REI error count is incremented by the value of the four REI bits (up to 8 per frame). Values of 9h - Fh are treated as zero errors. 10.8.6.4 Receive DS3 PLCP Overhead Extraction Overhead extraction extracts all of the DS3 PLCP path overhead bytes from the DS3 PLCP frame. All of the PLCP path overhead (POH) bytes (Z6 - Z1, F1, B1, G1, M2, M1, and C1) are output on the receive overhead bus (RPOHCLK, RPOH, and RPOHSOF). The B1 byte is output as an error indication (modulo 2 addition of the calculated BIP-8 and the B1 byte). In addition, the Z6 - Z1, F1, G1 (6:8), M2, and M1 bytes are integrated and stored in registers along with change indications. G1 (6:8) has an unstable indication as well. The F1 byte is sent to the receive trail trace buffer, and can also be sent to the receive HDLC controller. The M2 byte and/or M1 byte can be sent to the receive HDLC controller. The source of the data transferred to the receive HDLC controller is programmable (F1, M2, M1, or M2 & M1). If both the M2 and M1 byte are programmed to be the source for the receive HDLC controller, they are concatenated as a single data link as opposed to two separate data links. Once all frame processing has been completed, the ATM cells are passed on to the ATM/Packet Processor with a start of cell indication. 10.8.7 Transmit E3 PLCP Frame Processor The E3 PLCP frame format is shown in Figure 10-34. A1 and A2 are the sub-frame Alignment bytes that have a value of F6h and 28h, respectively. P8-P0 are the Path Overhead Identifier (POI) bytes that indicate the path overhead byte contained in the current sub-frame. Z3-Z1 are growth bytes reserved for future use. F1 is the Path User Channel byte allocated for user communications purposes (This byte is undefined in ATM). B1 is the Bit Interleaved Parity-8 (BIP-8) byte used for PLCP path error monitoring. G1 is the PLCP Path Status Byte (See Figure 10-35) used for far-end path status and performance monitoring (bits 6-8 are undefined in ATM). M2 and M1 are the DQDB Layer Management Information bytes used for DQDB layer management communications (These bytes are undefined in ATM). C1 is the Cycle/Stuff Counter byte used as for stuff indication. 155 DS3181/DS3182/DS3183/DS3184 Figure 10-34. E3 PLCP Frame Format A1 A2 P8 Z3 First Cell A1 A2 P7 Z2 Second Cell A1 A2 P6 Z1 Third Cell A1 A2 P5 F1 Fourth Cell A1 A2 P4 B1 Fifth Cell A1 A2 P3 G1 Sixth Cell A1 A2 P2 M2 Seventh Cell A1 A2 P1 M1 Eight Cell A1 A2 P0 C1 Ninth Cell 57 Columns 9 Rows Trailer 18 or 20 Bytes Figure 10-35. E3 PLCP G1 Byte Format G1 MSB 1 REI REI REI REI LSB 8 RAI LSS LSS LSS REI - Remote Error Indicator RAI - Remote Alarm Indicator LSS - Link Status Signal 10.8.7.1 Transmit E3 PLCP Trailer Generation E3 PLCP trailer generation inserts the E3 PLCP frame trailer immediately following sub-frame 0 (POI equals 01h), and generates the C1 byte. The trailer size is determined by the phase relationship of the G.751 E3 frame and PLCP frame and by the transmit 8 kHz reference clock. The trailer size is variable in all frames. The trailer size can be 17, 18, 19, 20, or 21 bytes. C1 is set to 3Bh, 4Fh, 75h, 9Dh, or A7h respectively, and the indicated number of bytes (17 - 21) are added after sub-frame 0. The trailer bytes are all set to 11001100. 10.8.7.2 Transmit E3 PLCP Frame Generation E3 PLCP frame generation receives the incoming PLCP payload data stream, and overwrites all of the overhead byte locations. The first two bytes of each sub-frame are overwritten with the frame alignment bytes A1 and A2, which have a value of F6h and 28h respectively. The third byte of sub-frame # is overwritten with POI byte # (P#). The value of P# is 00####0Pb (0 = a logic zero, #### = the hexadecimal value of #, and P = the odd parity bit). The fourth byte of sub-frames #8 - 6 are overwritten with the Z3 - Z1 bytes from the corresponding registers. 156 DS3181/DS3182/DS3183/DS3184 The fourth byte of sub-frame 5 is overwritten with the F1 byte from the corresponding register or the trail trace byte input from the transmit trail trace controller. The F1 byte from the corresponding register, the trail trace byte input from the transmit trail trace controller, or the HDLC Overhead Processor interface). The F1 byte source is programmable (PLCP.TCR.TF1C[1:0]) (trail trace data link, HDLC, or register). The fourth byte of sub-frame 4 is overwritten with the B1 byte, which is a BIP-8, calculated over all of the path overhead bytes and cell bytes of the previous frame after all PLCP processing (frame generation, error insertion, and overhead insertion) has been completed. The first four bits of the fourth byte of sub-frame 3 are overwritten with the G1 byte REI bits (G1[1:4]). The Remote Error Indication (REI) bits can be generated automatically or inserted from the G1 register bits. The REI source is programmable (auto or register). If the REI bits are generated automatically, they are set to zero when the receive side B1 byte exactly matches the BIP-8 calculated for the previous receives side frame. Otherwise, the REI is set to a value of one to eight to indicate the number of parity errors (BIP-8 errors) detected in the receive PLCP frame (B1 byte). The fifth bits of the fourth byte of sub-frame 3 is overwritten with the G1 byte RAI bit (G1[5]). The Remote Alarm Indication (RAI) bit is sourced from a register. The last three bits of the fourth byte of sub-frame 3 are overwritten with the G1 byte LSS bits (G1[6:8]). The Link Status Signal (LSS) bits are sourced from a register. The three register bits are inserted in the sixth, seventh, and eighth bits of the G1 byte in each frame. The fourth byte of sub-frames 2 and 1 are overwritten with the M2 and M1 bytes respectively. Each byte can be individually sourced from a register, or from the transmit HDLC Overhead Processor. The M2 byte and M1 byte sources are each programmable (register or HDLC). If both bytes are programmed to be sourced from the transmit HDLC controller, they are concatenated as a single data link as opposed to two separate data links. The fourth byte of sub-frame 0 is overwritten with the C1 byte created during trailer generation. Once all of the overhead bytes have been overwritten, the data stream is passed on to error insertion. 10.8.7.3 Transmit E3 PLCP Error Insertion Error insertion inserts various types of errors into the different overhead bytes. The types of errors that can be inserted are framing errors, BIP-8 parity errors, and Remote Error Indication (REI) errors. The type of framing error(s) inserted is programmable (frame bit error or framing byte error). A framing bit error is a single bit error in a frame alignment byte (A1 or A2) or POI byte (P#). A framing byte error is an error in all eight bits of a frame alignment byte (A1 or A2) or path overhead indicator (POI) byte (P#). Framing error(s) can be inserted one error at a time, or in two consecutive bytes (A1 & A2 or P# & P#+1). The framing error insertion rate (single A1 or A2, single P#, A1 & A2, or P# & P#+1) is programmable. The type of BIP-8 error(s) inserted is programmable (errored BIP-8 bit or errored BIP-8 byte). An errored BIP-8 bit is inverting a single bit error in the B1 byte. An errored BIP-8 byte is inverting all eight bits in the B1 byte. BIP-8 error(s) can be inserted one error at a time, or continuously. The BIP-8 error insertion rate (single or continuous) is programmable. The type of REI error(s) inserted is programmable (single REI error or eight REI errors). A single REI error is generated by setting the first four bits of the G1 byte to a value of 1h. Eight REI errors are generated by setting the first four bits of the G1 byte to a value of 8h. REI error(s) can be inserted one error at a time, or continuously. The REI error insertion rate (single or continuous) is programmable. Error insertion can be initiated by a register bit (PLCP.TEIR.TSEI) or initiated by the manual error insertion input (TMEI). Each error type is individually enabled by a register bit. The error insertion initiation type (register or input) is programmable. Once all error insertion has been performed, the data stream is passed on to overhead insertion. 10.8.7.4 Transmit E3 PLCP Overhead Insertion Overhead insertion can insert any (or all) of the path overhead bytes into the E3 PLCP frame. The overhead bytes Z3 - Z1, F1, B1, G1, M1, M2, and C1 can be sourced from the transmit overhead interface (TPOHCLK, TPOH, TPOHEN, and TPOHSOF). The B1 and C1 bytes are sourced as error masks (modulo 2 addition of the input B1/C1 byte and the generated B1/C1 byte). The overhead insertion is fully controlled by the transmit overhead interface. If the transmit PLCP overhead data enable signal (TPOHEN) is driven high, then the bit on the transmit PLCP overhead signal (TPOH) is inserted into the output data stream. Insertion of bits using the TPOH signal overwrites internal overhead insertion. 157 DS3181/DS3182/DS3183/DS3184 10.8.8 Receive E3 PLCP Frame Processor The Receive E3 PLCP Frame Processor performs E3 PLCP framing, byte destuffing, performance monitoring and overhead extraction. The E3 PLCP frame format is shown in Figure 10-34. A1 and A2 are the sub-frame Alignment bytes that have a value of F6h and 28h respectively. P8 - P0 are the Path Overhead Identifier (POI) bytes that indicate the path overhead byte contained in the current sub-frame. Z3 - Z1 are growth bytes reserved for future use. F1 is the Path User Channel byte allocated for user communications purposes (This byte is undefined in ATM). B1 is the Bit Interleaved Parity-8 (BIP-8) byte used for PLCP path error monitoring. G1 is the PLCP Path Status Byte (See Figure 10-35) used for far-end path status and performance monitoring (bits 6 - 8 are undefined in ATM). M1 and M2 are the DQDB Layer Management Information bytes used for DQDB layer management communications (These bytes are undefined in ATM). C1 is the Cycle/Stuff Counter byte used as for PLCP stuff indication. 10.8.8.1 Receive E3 PLCP Framing E3 PLCP framing determines the E3 PLCP frame boundary. The frame boundary is found by identifying the frame alignment bytes (A1 & A2), and the path overhead indicator (POI) byte (P#). The framer is an off-line framer that updates the data path frame counters when an out of frame (OOF) condition is present. The use of an off-line framer reduces the number of ATM cells discarded during the framing process. The continually searches for two consecutive sets of alignment bytes (A1 and A2), and two sequential POI bytes (P#) are identified. The data path frame counters are updated if an OOF condition is present). The maximum average reframe time is 23 s. 10.8.8.2 Receive E3 PLCP Byte Destuffing Byte destuffing discards the E3 PLCP frame trailer immediately following sub-frame 0 (POI equals 01h). The trailer size is determined by the cycle counter byte (C1). The trailer is 17 to 21 bytes. It is 17 bytes if C1 equals 3Bh; 18 bytes if C1 equals 4Fh; 19 bytes if C1 equals 75h; 20 bytes if C1 equals 9Dh; and 21 bytes if C1 equals A7h. The C1 codes provide error correction capability, and the C1 byte is corrected if required, and then used to determine the trailer size. Once the trailer size has been determined, the trailer bytes are discarded. 10.8.8.3 Receive E3 PLCP Performance Monitoring Performance monitoring checks the E3 PLCP frame for errors and alarm conditions. The alarm conditions detected are OOF, LOF, COFA, and RAI. All alarm conditions are defect conditions. The FEAC Controller does not integrate alarms for failure conditions. An Out Of Frame (OOF) condition is declared when an error is detected in both bytes in a framing word (A1 and A2) or two consecutive POI bytes (P0 - P11) are erred. An OOF condition is terminated when two sequential POI bytes and two consecutive framing words (A1 and A2) are error free or the E3 PLCP framer updates the data path frame counters. If the Loss Of Frame (LOF) integration counter is disabled, an LOF condition is declared when an OOF condition has been continuously present for 1 ms. If the LOF integration counter is enabled, an LOF condition is declared by the LOF integration counter when the counter has been active for a total of 1 ms. The LOF integration counter is active (increments count) when an OOF condition is present, it is inactive (holds count) when an OOF condition is absent, and it is reset when an OOF condition is continuously absent for 1 ms. An LOF condition is terminated when an OOF condition is continuously absent for 1 ms. A Change Of Frame Alignment (COFA) is declared when the E3 PLCP framer updates the data path frame counters with a frame alignment that is different from the current data path frame alignment. A Remote Alarm Indication (RAI) condition is declared when ten consecutive frames are received with the RAI bit (fifth bit of G1) set to one. An RAI condition is terminated when ten consecutive frames are received with the RAI bit set to zero. Three types of errors are accumulated: framing errors, BIP-8 errors and Remote Error Indication (REI) errors. Framing errors are determined by comparing A1, A2, and P# to their expected values. The type of framing errors accumulated is programmable (OOF, bit, byte, or word). An OOF error increments the count whenever an OOF condition is first detected (up to 1 per 3 sub-frames). A bit error increments the count once for each bit in A1, each bit in A2, and each bit in P# that does not match its expected value (up to 24 per sub-frame). A byte error increments the count once for each A1 byte, A2 byte, and P# byte that does not match its expected value (up to 3 per sub-frame). A word error increments the count once for each frame alignment word (A1, A2, and P#) that does 158 DS3181/DS3182/DS3183/DS3184 not match its expected value (up to 1 per sub-frame). The detection of POI byte (P#) framing errors is programmable (on or off). BIP-8 errors are determined by calculating the BIP-8 of the current frame (path overhead and cell bytes), and comparing the calculated BIP-8 to the B1 byte in the next frame. The type of BIP-8 errors accumulated is programmable (bit or block). A bit error increments the count once for each bit in the B1 byte that does not match the corresponding bit in the calculated BIP-8 (up to 8 per frame). A block error increments the count if any bit in the B1 byte does not match the corresponding bit in the calculated BIP-8 (up to 1 per frame). REI errors are determined by the four REI bits (first four bits of G1). The count is incremented by the value of the four REI bits (up to 8 per frame). Values of 9h - Fh are treated as zero errors. 10.8.8.4 Receive E3 PLCP Overhead Extraction Overhead extraction extracts all of the E3 PLCP path overhead bytes from the E3 PLCP frame. All of the PLCP path overhead (POH) bytes (Z3 - Z1, F1, B1, G1, M1, M2, and C1) are output on the receive overhead bus (RPOHCLK, RPOH, and RPOHSOF). The B1 byte is output as an error indication (modulo 2 addition of the calculated BIP-8 and the B1 byte). In addition, the Z3 - Z1, F1, G1 (6:8), M1, and M2 bytes are integrated and stored in registers along with change indications. G1 (6:8) has an unstable indication as well. The F1 byte is sent to the receive trail trace buffer, and can also be sent to the receive HDLC controller. The M2 byte and/or M1 byte can be sent to the receive HDLC controller. The source of the data transferred to the receive HDLC controller is programmable (F1, M2, M1, or M2 & M1). If both the M2 and M1 bytes are programmed to be the source for the receive HDLC controller, they are concatenated as a single data link as opposed to two separate data links. Once all frame processing has been completed, the ATM cells are passed on to the ATM/Packet Processor with a start of cell indication. 159 DS3181/DS3182/DS3183/DS3184 10.9 Fractional Payload Controller 10.9.1 General Description The Fractional Payload Controller uses a fraction of the DS3/E3 payload for ATM cell or HDLC packets. The unused DS3/E3 payload is considered fractional overhead and can be used as a proprietary data link. The allocation given to the fractional payload is programmable controlled using internal counters or controlled externally. The fractional overhead data can optionally be programmed to transmit all 0's, all 1's, a 1010 pattern, or insert data from an external source. The Fractional Payload Controller demaps fractional payload and overhead data from the DS3/E3 payload in the receive direction and maps fractional payload and overhead data into the DS3/E3 payload in the transmit direction. The receive direction extracts the fractional payload and fractional overhead data bits from the receive DS3/E3 payload, performs fractional payload/overhead data demultiplexing, sends the fractional payload to the ATM/Packet processor, and sends the fractional overhead data to an external interface. The transmit direction accepts the fractional overhead from an internal register or the external interface and fractional payload data from the ATM/Packet processor, performs fractional overhead/payload data multiplexing, and inserts the fractional overhead and payload data into the transmit DS3/E3 payload. See Figure 10-36 for the location of the Fractional Payload Controller in the DS318x devices. Figure 10-36. Fractional Payload Controller Detailed Block Diagram TAIS TUA1 Clock Rate Adapter B3ZS/ HDB3 Decoder IEEE P1149.1 JTAG Test Access Port Tx Packet Processor TX BERT HDLC DS3 / E3 Receive Framer RX BERT RX FRAC/ PLCP UA1 GEN Tx FIFO System Interface Trail Trace Buf f er PLB FEAC TX FRAC/ PLCP Tx Cell Processor SLB DLB LLB ALB DS3/E3 Transmit LIU DS3/E3 Receive LIU DS3 / E3 Transmit Formatter B3ZS/ HDB3 Encoder Rx Packet Processor Rx Cell Processor Rx FIFO Microprocessor Interface 10.9.2 Features * * * Programmable payload allocation - The payload data and fractional overhead allocation can be programmed via registers. Externally controlled payload allocation - The payload data and fractional overhead allocation can be controlled by an external source via pins. Fractional overhead extraction and insertion - Extracts all fractional overhead from the DS3/E3 payload and sends it to an external serial interface. Inserts all fractional overhead from a serial interface and into the transmit DS3/E3 payload. Optionally, the transmit fractional overhead can be set to insert all 0's, all 1's, or a 1010 pattern. 160 DS3181/DS3182/DS3183/DS3184 10.9.3 Transmit Fractional Interface The Transmit Fractional Interface receives the payload data stream from the ATM/Packet Processor and inserts a fractional overhead stream. The incoming fractional overhead stream consists of fractional overhead (TFOHn), input fractional overhead enable (TFOHENIn), and output fractional overhead enable (TFOHENOn). TFOHn, TFOHENOn and TFOHENIn are typically referenced to TCLKIn (but also could be referenced to the TLCLKn, TCLKOn/TGCLKn, RCLKOn or RLCLKn clock pins). If external control is enabled, TFOHENIn marks the fractional overhead periods, and TFOHENOn is held low. If internal control is enabled, TFOHENOn marks the fractional overhead periods, and TFOHENIn is ignored. Fractional overhead control is programmable (internal or external). The fractional overhead source is programmable (all 0's, all 1's, a 10 pattern, or TFOH). See the FRAC.TCR Register Definition. See Section 8.3.3 above for specific timing relationships between these pins. 10.9.4 Transmit Fractional Controller The Transmit Fractional Controller generates the transmit fractional overhead enable output (TFOHENOn) used in internal control mode to insert fractional overhead. The outgoing transmit data stream to the DS3/E3 Framer is divided into frames. Each frame is composed of data groups that have a programmable size (1 - 8191 bits). Each data group is divided into two sections. The first section (Section A) has a programmable size (0 - 8191 bits). The second section (Section B) contains the remaining bits (g - a bits). See Figure 10-37. The section that contains fractional overhead is programmable (Section A or Section B by setting the FRAC.TCR.TSASS register bit). TFOHENOn is high during the fractional overhead section of the data group, and low during the payload section of the data group. TFOHENOn is also low during line overhead/stuff periods. 10.9.5 Receive Fractional Interface The Receive Fractional Interface receives the DS3/E3 payload from the DS3/E3 Framer, and performs fractional overhead extraction on the payload. The receive fractional overhead pins are the input fractional overhead enable (RFOHENIn), and the output fractional overhead enable (RFOHENOn). RFOHENIn is sampled on the rising edge of RCLKOn, typically, or it can be referenced to the RLCLKn pin. RFOHENOn is updated on the rising edge of RCLKOn (or alternatively the RLCLKn pin). If external control is enabled, the receive fractional overhead enable input (RFOHENIn) marks the fractional overhead bits contained in the DS3/E3 payload. RFOHENIn is high while a fractional overhead period is available on RSERn. RFOHENIn is low during payload data or line overhead/stuff periods. If internal control is enabled, the receive fractional overhead enable output (RFOHENOn) marks the fractional overhead bits in the received DS3/E3 payload. RFOHENOn is high during a fractional overhead bit period on RSERn. RFOHENOn is low during a payload data or line overhead/stuff period. See Section 8.3.3 above for specific timing relationships between these pins. 10.9.6 Receive Fractional Controller The Receive Fractional Controller generates the receive fractional overhead enable output (RFOHENOn) used in internal control mode to extract fractional overhead to the RFOHn pin. The DS3/E3 payload is divided into frames composed of data groups that have a programmable size (1 - 8191 bits). Each data group is divided into two sections. The first section (Section A) has a programmable size (a, 0 - 8191 bits). The second section (Section B) contains the remaining bits (g - a bits). See Figure 10-37. The section that contains fractional overhead is programmable (Section A or Section B by setting the FRAC.RCR.RSASS register bit). RFOHENOn is high during the fractional overhead section of the data group, and low during the payload section of the data group. RFOHENOn is also low during line overhead/stuff periods. The first bit of a frame is the first bit of a data group. If a frame does not contain an integer number of data groups (f / g is not an integer), the last data group in the frame will be a short data group. The last bit of the short data group will be the last data period before the start of frame period. 161 DS3181/DS3182/DS3183/DS3184 Figure 10-37. Data Group Format Data Group (g bits) Section A (a bits) Section B (g-a bits) Figure 10-38. Frame Format Frame (f bits) Data Group Data Group Data Group *** Data Group 162 Data Group Data Group DS3181/DS3182/DS3183/DS3184 10.10 DS3/E3 Framer/Formatter 10.10.1 General Description The Receive DS3/E3 Framer receives a unipolar DS3/E3 signal, determines frame alignment and extracts the DS3/E3 overhead in the receive direction. The Transmit DS3/E3 Formatter receives a DS3/E3 payload, generates framing, inserts DS3/E3 overhead, and outputs a unipolar DS3/E3 signal in the transmit direction. The Receive DS3/E3 Framer receives a DS3/E3 signal, determines the frame alignment, extracts the DS3/E3 overhead, and outputs the payload with frame and overhead The Transmit DS3/E3 Formatter receives a DS3/E3 payload from the ATM/Packet Processor, generates a DS3/E3 frame, optionally inserts DS3/E3 overhead, and transmits the DS3/E3 signal. See Figure 10-39 for the location of the DS3/E3 Framer/Formatter blocks in the DS318x devices. Figure 10-39. Framer Detailed Block Diagram TAIS TUA1 DS3/E3 Receive LIU B3ZS/ HDB3 Decoder Clock Rate Adapter TX BERT RX BERT RX FRAC/ PLCP UA1 GEN Tx FIFO Tx Packet Processor HDLC DS3 / E3 Receive Framer IEEE P1149.1 JTAG Test Access Port Tx Cell Processor System Interface Trail Trace Buf f er PLB FEAC TX FRAC/ PLCP SLB DLB LLB ALB DS3 / E3 Transmit Formatter B3ZS/ HDB3 Encoder DS3/E3 Transmit LIU Rx Packet Processor Rx Cell Processor Rx FIFO Microprocessor Interface 10.10.2 Features 10.10.2.1 Transmit Formatter * * * * * * * Programmable DS3 or E3 formatter - Accepts a DS3 (M23 or C-bit) or E3 (G.751 or G.832) signal and performs DS3/E3 overhead generation. Arbitrary framing format support - Generates a signal with an arbitrary framing format. The line overhead/stuff periods are added into the data stream using an overhead mask signal. Generates alarms and errors - DS3 alarm conditions (AIS, RDI, and Idle) and errors (framing, parity, and FEBE), or E3 alarm conditions (AIS and RDI/RAI) and errors (framing, parity, and REI) can be inserted into the outgoing data stream. Externally controlled serial DS3/E3 overhead insertion port - Can insert all DS3 or E3 overhead via a serial interface. DS3/E3 overhead insertion is fully controlled via the serial overhead interface. HDLC overhead insertion - An HDLC channel can be inserted into the DS3 or E3 data stream. FEAC insertion - A FEAC channel can be inserted into the DS3 or E3 data stream. Trail Trace insertion - Inputs and inserts the G.832 E3 TR byte. 10.10.2.2 Receive Framer * Programmable DS3 or E3 framer - Accepts a DS3 (M23 or C-bit) or E3 (G.751 or G.832) signal and performs DS3/E3 overhead termination. 163 DS3181/DS3182/DS3183/DS3184 * * * * * * Arbitrary framing format support - Accepts a signal with an arbitrary framing format. The Line overhead/stuff periods are removed from the data stream using an overhead mask signal. Detects alarms and errors - Detects DS3 alarm conditions (SEF, OOMF, OOF, LOF, COFA, AIS, AIC, RDI, and Idle) and errors (framing, parity, and FEBE), or E3 alarm conditions (OOF, LOF, COFA, AIS, and RDI/RAI) and errors (framing, parity, and REI). Serial DS3/E3 overhead extraction port - Extracts all DS3 or E3 overhead and outputs it on a serial interface. HDLC overhead extraction - An HDLC channel can be extracted from the DS3 or E3 data stream. FEAC extraction - A FEAC channel can be extracted from the DS3 or E3 data stream. Trail Trace extraction - Extracts and outputs the G.832 E3 TR byte. 10.10.3 Transmit Formatter The Transmit Formatter receives a DS3, E3 or CC52 clear-channel data stream and performs framing generation, error insertion, overhead insertion, and AIS/Idle generation for C-bit DS3, M23 DS3, G.751 E3, G.832 E3, or CC52 clear-channel framing protocols. In clear-channel mode, only AIS/Idle generation is performed. The bits in a byte are transmitted MSB first, LSB last. When they are input serially, they are input in the order they are to be transmitted. The bits in a byte in an outgoing signal are numbered in the order they are transmitted, 1 (MSB) to 8 (LSB). However, when a byte is stored in a register, the MSB is stored in the highest numbered bit (7), and the LSB is stored in the lowest numbered bit (0). This is to differentiate between a byte in a register and the corresponding byte in a signal. After all frame formatting is completed, the frame processor inserts a DS3/E3 (or Clear Channel) data stream into a line data stream (OHM modes only). The line data stream is an upper level signal with a DS3, E3, or clear-channel data stream embedded within the upper level frame. For example, if a DS3 signal has two line overhead/stuff periods occur between the beginning of one frame and the beginning of the next frame, there will be 4762 clock periods between the beginnings of the two frames (4760 for the DS3 data periods plus two for the line overhead/stuff periods). 10.10.4 Receive Framer The Receive Framer receives the incoming DS3, E3, or clear-channel line/tributary data stream, performs appropriate framing, terminates and extracts the associated overhead bytes, and extracts the DS3, E3, or clearchannel payload data stream (OHM modes only). The line data stream is an upper-level signal with a DS3, E3, or clear-channel data stream embedded within the upper level frame. For example, if a DS3 signal has two line overhead/stuff periods occur between the beginning of one frame and the beginning of the next frame, there will be 4762 clock periods between the beginnings of the two frames (4760 for the DS3 data periods plus two for the line overhead/stuff periods). The Receive Framer processes a C-bit format DS3, M23 format DS3, G.751 format E3, G.832 format E3, or clearchannel data stream, performing framing, performance monitoring, overhead extraction, and generates downstream AIS, if necessary. In clear-channel mode, only performance monitoring and downstream AIS generation are performed. The bits in a byte are received MSB first, LSB last. When they are output serially, they are output MSB first, LSB last. The bits in a byte in an incoming signal are numbered in the order they are received, 1 (MSB) to 8 (LSB). However, when a byte is stored in a register, the MSB is stored in the highest numbered bit (7), and the LSB is stored in the lowest numbered bit (0). This is to differentiate between a byte in a register and the corresponding byte in a signal. Some bits, bit groups, or bytes (data) are integrated before being stored in a register. Integration requires the data to have the same new data value for five consecutive occurrences before the new data value will be stored in the data register. Unless stated otherwise, integrated data may have an associated unstable indication. Integrated data is considered unstable if the received data value does not match the currently stored (integrated) data value or the previously received data value for eight consecutive occurrences. The unstable condition is terminated when the same value is received for five consecutive occurrences. 10.10.4.1.1 Receive DS3 Framing DS3 framing determines the DS3 frame boundary. In order to identify the DS3 frame boundary, first the sub-frame boundary must be found. The sub-frame boundary is found by identifying the sub-frame alignment bits FX1, FX2, FX3, and FX4, which have a value of one, zero, zero, and one respectively. See Figure 10-40. Once the sub-frame 164 DS3181/DS3182/DS3183/DS3184 boundary is found, the multiframe frame boundary can be found. The multiframe boundary is found by identifying the multiframe alignment bits M1, M2, and M3, which have a value of zero, one, and zero respectively. The DS3 framer is an off-line framer that only updates the data path frame counters when either an out of frame (OOF) or an out of multiframe (OOMF) condition is present. The use of an off-line framer reduces the average time required to reframe, and reduces data loss caused by burst error. The DS3 framer has a Maximum Average Reframe Time (MART) of approximately 1.0ms. Figure 10-40. DS3 Frame Format X1 F11 C11 F12 C12 F13 C13 F14 X2 F21 C21 F22 C22 F23 C23 F24 P1 F31 C31 F32 C32 F33 C33 F34 P2 F41 C41 F42 C42 F43 C43 F44 M1 F51 C51 F52 C52 F53 C53 F54 M2 F61 C61 F62 C62 F63 C63 F64 M3 F71 C71 F72 C72 F73 C73 F74 7 SubFrames 680 Bits The sub-frame framer continually searches four adjacent bit positions for a sub-frame boundary. A sub-frame alignment bit (F-bit) checker checks each bit position. All four-bit positions must fail before any other bit positions are checked for a sub-frame boundary. There are 170 possible bit positions that must be checked, and four positions are checked simultaneously. Therefore up to 43 checks may be needed to identify the sub-frame boundary. The sub-frame framer enables the multiframe frame once it has identified a sub-frame boundary. See Figure 10-41 for the sub-frame framer state diagram. 165 DS3181/DS3182/DS3183/DS3184 Figure 10-41. DS3 Sub-Frame Framer State Diagram its F-b 16 iled s fa o si tio on siti it p po 3b bit ns l4 Al fai led or ver ifie d Sync All 4 bit positions failed Verify Load 2 F-bits loaded The multiframe framer checks for a multiframe boundary. When the multiframe framer identifies a multiframe boundary, it updates the data path frame counters if either an OOF or OOMF condition is present. The multiframe framer waits until a sub-frame boundary has been identified. Then, each bit position is checked for the multiframe boundary. The multiframe boundary is found by identifying the three multiframe alignment bits (M-bits). Since there are seven multiframe bits and three bits are required to identify the multiframe boundary, up to 9 checks may be needed to find the multiframe boundary. Once the multiframe boundary is identified, it is checked in each subsequent frame. The data path frame counters are updated if the three multiframe alignment bits are error free, and an OOF or OOMF condition exists. If the multiframe framer checks more than 15 multiframe bit (X-bits, P-bits, and M-bits) positions without identifying the multiframe boundary, the multiframe framer times out, and forces the sub-frame framer back into the load state. See Figure 10-42 for the multiframe framer state diagram. 10.10.4.1.2 Receive DS3 Performance Monitoring Performance monitoring checks the DS3 frame for alarm conditions and errors. The alarm conditions detected are OOMF, OOF, SEF, LOF, COFA, LOS, AIS, Idle, RUA1, and RDI. The errors accumulated are framing, P-bit parity, C-bit parity (C-bit format only), and Far-End Block Error (FEBE) (C-bit format only) errors. An Out Of Multiframe (OOMF) condition is declared when a multiframe alignment bit (M-bit) error has been detected in two or more of the last four consecutive DS3 frames, or when a manual - is requested. An OOMF condition is terminated when no M-bit errors have been detected in the last four consecutive DS3 frames, or when the DS3 framer updates the data path frame counters. See Figure 10-42 for the multiframe framer state diagram. 166 DS3181/DS3182/DS3183/DS3184 Figure 10-42. DS3 Multiframe Framer State Diagram bit Mor err eou Mbit tim err or and Mbi t s id ent ifie d Sync t Timeout Verify Load 2 multiframe loaded If multiframe alignment OOF is disabled, an Out Of Frame (OOF) condition is declared when three or more out of the last 16 consecutive sub-frame alignment bits (F-bits) have been errored, or a manual resynchronization is requested. If multiframe alignment OOF is enabled, an OOF condition is declared when three or more out of the last 16 consecutive F-bits have been errored, when an OOMF condition is declared, or when a manual resynchronization is requested. If multiframe alignment OOF is disabled, an OOF condition is terminated when none of the last 16 consecutive F-bits has been errored, or when the DS3 framer updates the data path frame counters. If multiframe alignment OOF is enabled, an OOF condition is terminated when an OOMF condition is not active and none of the last 16 consecutive F-bits has been errored, or when the DS3 framer updates the data path frame counters. Multiframe alignment OOF is programmable (on or off). A Severely Errored Frame (SEF) condition is declared when three or more out of the last 16 consecutive F-bits have been errored, or when a manual resynchronization is requested. An SEF condition is terminated when an OOF condition is absent. A Loss Of Frame (LOF) condition is declared by the LOF integration counter when it has been active for a total of T ms. The LOF integration counter is active (increments count) when an OOF condition is present, it is inactive (holds count) when an OOF condition is absent, and it is reset when an OOF condition is absent for T continuous ms. T is programmable (0, 1, 2, or 3). An LOF condition is terminated when an OOF condition is absent for T continuous ms. A Change Of Frame Alignment (COFA) is declared when the DS3 framer updates the data path frame counters with a frame alignment that is different from the current data path DS3 frame alignment. A Loss Of Signal (LOS) condition is declared when the B3ZS encoder is active, and it declares a LOS condition. A LOS condition is terminated when the B3ZS encoder is inactive, or it terminates a LOS condition. An Alarm Indication Signal (AIS) is a DS3 signal with valid F-bits and M-bits. The X-bits (X1 and X2) are set to one, the P-bits (P1 and P2) are set to zero, all C-bits (CXY) are set to zero, and the payload bits are set to a 1010 pattern starting with a one immediately after each DS3 overhead bit. An AIS signal is present when a DS3 frame is received with valid F-bits and M-bits, both X-bits set to one, both P-bits set to zero, all C-bits set to zero, and all but seven or fewer payload data bits matching the DS3 overhead aligned 1010 pattern. An AIS signal is absent when a DS3 frame is received that does not meet the aforementioned criteria for an AIS signal being present. The AIS integration counter declares an AIS condition when it has been active for a total of 10 to 17 DS3 frames. The AIS integration counter is active (increments count) when an AIS signal is present, it is inactive (holds count) when an 167 DS3181/DS3182/DS3183/DS3184 AIS signal is absent, and it is reset when an AIS signal is absent for 10 to 17 consecutive DS3 frames. An AIS condition is terminated when an AIS signal is absent for 10 to 17 consecutive DS3 frames. A Receive Unframed All 1's (RUA1) condition is declared if in each of 4 consecutive 2047 bit windows, five or less zeros are detected and an OOF condition is continuously present. A RUA1 condition is terminated if in each of 4 consecutive 2047-bit windows, six or more zeros are detected or an OOF condition is continuously absent. An Idle Signal (Idle) is a DS3 signal with valid F-bits, M-bits, and P-bits (P1 and P2). The X-bits (X1 and X2) are set to one, C31, C32, and C33 are set to zero, and the payload bits are set to a 1100 pattern starting with 11 immediately after each overhead bit. In C-bit mode, an Idle signal is present when a DS3 frame is received with valid F-bits, Mbits, and P-bits, both X-bits set to one, C31, C32, and C33 set to zero, and all but seven or fewer payload data bits matching the overhead aligned 1100 pattern. In M23 mode, an Idle signal is present when a DS3 frame is received with valid F-bits, M-bits, and P-bits, both X-bits set to one, and all but seven or fewer payload data bits matching the T3 overhead aligned 1100 pattern. An Idle signal is absent when a DS3 frame is received that does not meet aforementioned criteria for an Idle signal being present. The Idle integration counter declares an Idle condition when it has been active for a total of 10 to 17 DS3 frames. The Idle integration counter is active (increments count) when an Idle signal is present, it is inactive (holds count) when an Idle signal is absent, and it is reset when an Idle signal is absent for 10 to 17 consecutive DS3 frames. An Idle condition is terminated when an Idle signal is absent for 10 to 17 consecutive DS3 frames. A Remote Defect Indication (RDI) condition (also called a far-end SEF/AIS defect condition) is declared when four consecutive DS3 frames are received with the X-bits (X1 and X2) set to zero. An RDI condition is terminated when four consecutive DS3 frames are received with the X-bits set to one. A DS3 Framing Format Mismatch (DS3FM) condition is declared when the DS3 format programmed (M23, C-bit) does not match the incoming DS3 signal-framing format. A DS3FM condition is terminated when the incoming DS3 signal-framing format is the same format as programmed. Framing errors are determined by comparing F-bits and M-bits to their expected values. The type of framing errors accumulated is programmable (OOF, F & M, F, or M). An OOF error increments the count whenever OOF condition is first detected. An F & M error increments the count once for each F-bit or M-bit that does not match its expected value (up to 31 per DS3 frame). An F error increments the count once for each F-bit that does not match its expected value (up to 28 per DS3 frame). An M error increments the count once for each M-bit that does not match its expected value (up to 3 per DS3 frame). P-bit parity errors are determined by calculating the parity of the current DS3 frame (payload bits only), and comparing the calculated parity to the P-bits (P1 and P2) in the next DS3 frame. If the calculated parity does not match P1 or P2, a single P-bit parity error is declared. C-bit parity errors (C-bit format only) are determined by calculating the parity of the current DS3 frame (payload bits only), and comparing the calculated parity to the C-bits in sub-frame three (C31, C32, and C33) in the next DS3 frame. If the calculated parity does not match C31, C32, or C33, a single C-bit parity error is declared. FEBE errors (C-bit format only) are determined by the C-bits in sub-frame four (C41, C42, and C43). A value of 111 indicates no error and any other value indicates an error. 10.10.5 C-bit DS3 Framer/Formatter 10.10.5.1 Transmit C-bit DS3 Frame Processor The C-bit DS3 frame format is shown in Figure 10-40. Table 10-34 shows the function of each overhead bit in the DS3 Frame 168 DS3181/DS3182/DS3183/DS3184 Table 10-34. C-Bit DS3 Frame Overhead Bit Definitions BIT DEFINITION X1, X2 Remote Defect Indication (RDI) P1, P2 Parity Bits M1, M2, and M3 Multiframe Alignment Bits FXY Sub-frame Alignment Bits C11 Application Identification Channel (AIC) C12 Reserved C13 Far-End Alarm and Control (FEAC) signal C21, C22, and C23 Unused C31, C32, and C33 C-bit parity bits C41, C42, and C43 Far-End Block Error (FEBE) bits C51, C52, and C53 Path Maintenance Data Link (or HDLC) bits C61, C62, and C63 Unused C71, C72, and C73 Unused X1 and X2 are the Remote Defect Indication (RDI) bits (also referred to as the far-end SEF/AIS bits). P1 and P2 are the parity bits used for line error monitoring. M1, M2, and M3 are the multiframe alignment bits. FXY are the subframe alignment bits. C11 is the Application Identification Channel (AIC). C12 is reserved for future network use, and has a value of one. C13 is the Far-End Alarm and Control (FEAC) signal. C21, C22, and C23 are unused, and have a value of one. C31, C32, and C33 are the C-bit parity bits used for path error monitoring. C41, C42, and C43 are the FarEnd Block Error (FEBE) bits used for remote path error monitoring. C51, C52, and C53 are the path maintenance data link (or HDLC) bits. C61, C62, and C63 are unused, and have a value of one. C71, C72, and C73 are unused, and have a value of one. The X-bit, P-bit, M-bit, C-bit, and F-bit positions are overhead bits, and the other bit positions in the DS3 frame are payload bits. 10.10.5.2 Transmit C-bit DS3 Frame Generation C-bit DS3 frame generation receives the incoming payload data stream, and overwrites the entire overhead bit locations. The multiframe alignment bits (M1, M2, and M3) are overwritten with the values zero, one, and zero (010) respectively. The sub-frame alignment bits (FX1, FX2, FX3, and FX4) are overwritten with the values one, zero, zero, and one (1001) respectively. The X-bits (X1 and X2) are both overwritten with the Remote Defect Indicator (RDI). The RDI source is programmable (automatic, 1, or 0). If the T3.TCR.ARDID is one then the T3.TCR.TRDI register bit controls this bit. If the RDI is generated automatically (T3.TCR.ARDID=0), the X-bits are set to zero when one or more of the indicated alarm conditions is present, and set to one when all of the indicated alarm conditions are absent. Automatically setting RDI on LOS, SEF, LOF, or AIS is individually programmable (on or off). The P-bits (P1 and P2) are both overwritten with the calculated payload parity from the previous DS3 frame. The payload parity is calculated by performing modulo 2 addition of all of the payload bits after all frame processing has been completed. P-bit generation is programmable (on or off) via the T3.TCR.PBGE register bit. The P-bits will be generated if either P-bit generation is enabled or frame generation is enabled. The bits C11, C12, C21, C22, C23, C61, C62, C63, C71, C72, and C73 are all overwritten with a one. 169 DS3181/DS3182/DS3183/DS3184 The bit C13 is overwritten with the Far-End Alarm and Control (FEAC) data input from the transmit FEAC controller. The bits C31, C32, and C33 are all overwritten with the calculated payload parity from the previous DS3 frame. The bits C41, C42, and C43 are all overwritten with the Far-End Block Error (FEBE) bit. The FEBE bit can be generated automatically or inserted from a register bit. The FEBE bit source is programmable (automatic or register). If the T3.TCR.AFEBED register bit is one then the T3.TCR.TFEBE register bit controls this bit. If the FEBE bit is generated automatically, it is zero when at least one C-bit parity error has been detected during the previous frame. The bits C51, C52, and C53 are overwritten with the path maintenance data link input from the HDLC controller. Once all of the DS3 overhead bits have been overwritten, the data stream is passed on to error insertion. If frame generation is disabled, the incoming DS3 signal is passed on to error insertion. Frame generation is programmable (on or off). Note: P-bit generation may still be performed even if frame generation is disabled. 10.10.5.3 Transmit C-bit DS3 Error Insertion Error insertion inserts various types of errors into the different DS3 overhead bits. The types of errors that can be inserted are framing errors, P-bit parity errors, C-bit parity errors, and Far-End Block Error (FEBE) errors. The framing error insertion mode is programmable (F-bit, M-bit, SEF, or OOMF). An F-bit error is a single subframe alignment bit (FXY) error. An M-bit error is a single multiframe alignment bit (M1, M2, or M3) error. An SEF error is an error in all the sub-frame alignment bits in a sub-frame (FX1, FX2, FX3, and FX4). An OOMF error is a single multiframe alignment bit (M1, M2, or M3) error in two consecutive DS3 frames. A P-bit parity error is generated by is inverting the value of the P-bits (P1 and P2) in a single DS3 frame. P-bit parity error(s) can be inserted one error at a time, or continuously. The P-bit parity error insertion mode (single or continuous) is programmable. A C-bit parity error is generated by is inverting the value of the C31, C32, and C33 bits in a single DS3 frame. C-bit parity error(s) can be inserted one error at a time, or continuously. The C-bit parity error insertion mode (single or continuous) is programmable. A FEBE error is generated by forcing the C41, C42, and C43 bits in a single multiframe to zero. FEBE error(s) can be inserted one error at a time, or continuously. The FEBE error insertion rate (single or continuous) is programmable. Each error type (framing, P-bit parity, C-bit parity, or FEBE) has a separate enable. Continuous error insertion mode inserts errors at every opportunity. Single error insertion mode inserts an error at the next opportunity when requested. The framing multi-error modes (SEF or OOMF) insert the indicated number of error(s) at the next opportunities when requested; i.e., a single request will cause multiple errors to be inserted. The requests can be initiated by a register bit (TSEI) or by the manual error insertion input (TMEI). The error insertion initiation type (register or input) is programmable. The insertion of each particular error type is individually enabled. Once all error insertion has been performed, the data stream is passed on to overhead insertion. 10.10.5.4 Transmit C-bit DS3 Overhead Insertion Overhead insertion can insert any (or all) of the DS3 overhead bits into the DS3 frame. The DS3 overhead bits X1, X2, P1, P2, MX, FXY, and CXY can be sourced from the transmit overhead interface (TOHCLKn, TOHn, TOHENn, and TOHSOFn). The P-bits (P1 and P2) and C31, C32, and C33 bits are received as an error mask (modulo 2 addition of the input bit and the internally generated bit). The DS3 overhead insertion is fully controlled by the transmit overhead interface. If the transmit overhead data enable signal (TOHENn) is driven high, then the bit on the transmit overhead signal (TOHn) is inserted into the output data stream. Insertion of bits using the TOHn signal overwrites internal overhead insertion. 10.10.5.5 Transmit C-bit DS3 AIS/Idle Generation C-bit DS3 AIS/Idle generation overwrites the data stream with AIS or an Idle signal. If transmit Idle is enabled, the data stream payload is forced to an 1100 pattern with two ones immediately following each DS3 overhead bit. M1, M2, and M3 bits are overwritten with the values zero, one, and zero (010) respectively. FX1, FX2, FX3, and FX4 bits are overwritten with the values one, zero, zero, and one (1001) respectively. X1 and X2 are overwritten with 11. And, P1, P2, C31, C32, and C33 are overwritten with the calculated payload parity from the previous output DS3 frame. If transmit AIS is enabled, the data stream payload is forced to a 1010 pattern with a one immediately following each DS3 overhead bit. M1, M2, and M3 bits are overwritten with the values zero, one, and zero (010) respectively. FX1, FX2, FX3, and FX4 bits are overwritten with the values one, zero, zero, and one (1001) respectively. X1 and X2 170 DS3181/DS3182/DS3183/DS3184 are overwritten with 11. P1, P2, C31, C32, and C33 are overwritten with the calculated payload parity from the previous output DS3 frame. And, CX1, CX2, and CX3 (X 3) are overwritten with 000. AIS will overwrite a transmit Idle signal. 10.10.5.5.1 Receive C-bit DS3 Frame Format The DS3 frame format is shown in Figure 10-40. X1 and X2 are the Remote Defect Indication (RDI) bits (also referred to as the far-end SEF/AIS bits). P1 and P2 are the parity bits used for line error monitoring. M1, M2, and M3 are the multiframe alignment bits that define the multiframe boundary. FXY are the sub-frame alignment bits that define the sub-frame boundary. Note: Both the M-bits and F-bits define the DS3 frame boundary. C11 is the Application Identification Channel (AIC). C12 is reserved for future network use, and has a value of one. C13 is the Far-End Alarm and Control (FEAC) signal. C21, C22, and C23 are unused, and have a value of one. C31, C32, and C33 are the C-bit parity bits used for path error monitoring. C41, C42, and C43 are the Far-End Block Error (FEBE) bits used for remote path error monitoring. C51, C52, and C53 are the path maintenance data link (or HDLC) bits. C61, C62, and C63 are unused, and have a value of one. C71, C72, and C73 are unused, and have a value of one. 10.10.5.5.2 Receive C-bit DS3 Overhead Extraction Overhead extraction extracts all of the DS3 overhead bits from the C-bit DS3 frame. All of the DS3 overhead bits X1, X2, P1, P2, MX, FXY, and CXY are output on the receive overhead interface (ROH, ROHSOF, and ROHCLK). The P1, P2, C31, C32, and C33 bits are output as an error indication (modulo 2 addition of the calculated parity and the bit). In addition, the Application Identification Channel (AIC), which is stored in a register bit, is determined from the C11 bit. The AIC is set to one (C-bit format) if the C11 bit is set to one in 31 consecutive multiframes. The AIC is set to zero (M23 format) if the C11 bit is set to zero in four of the last 31 consecutive multiframes. Note: The stored AIC bit must not change when a LOS, OOF, or AIS condition is present. The C13 bit is sent over to the receive FEAC controller. The C51, C52, and C53 bits are sent to the receive HDLC overhead controller. 10.10.6 M23 DS3 Framer/Formatter 10.10.6.1 Transmit M23 DS3 Frame Processor The M23 DS3 frame format is shown in Figure 10-40. Table 10-35 defines the framing bits for M23 DS3. X1 and X2 are the Remote Defect Indication (RDI) bits (also referred to as the far-end SEF/AIS bits). P1 and P2 are the parity bits used for line error monitoring. M1, M2, and M3 are the multiframe alignment bits. FXY are the sub-frame alignment bits. C11 is the Application Identification Channel (AIC). CX1, CX2, and CX3 are the stuff control bits for tributary #X. The X-bit, P-bit, M-bit, C-bit, and F-bit positions are overhead bits, and the other bit positions in the DS3 frame are payload bits. Table 10-35. M23 DS3 Frame Overhead Bit Definitions BIT DEFINITION X1, X2 Remote Defect Indication (RDI) P1, P2 Parity Bits M1, M2, and M3 Multiframe Alignment Bits FXY Sub-frame Alignment Bits C11 Application Identification Channel (AIC) CX1, CX2, and CX3 Stuff Control Bits for Tributary #X 171 DS3181/DS3182/DS3183/DS3184 10.10.6.2 Transmit M23 DS3 Frame Generation M23 DS3 frame generation receives the incoming payload data stream, and overwrites the entire DS3 overhead bit locations. The multiframe alignment bits (M1, M2, and M3) are overwritten with the values zero, one, and zero (010) respectively. The sub-frame alignment bits (FX1, FX2, FX3, and FX4) are overwritten with the values one, zero, zero, and one (1001) respectively. The X-bits (X1 and X2) are both overwritten with the Remote Defect Indicator (RDI). The RDI source is programmable (automatic, 1, or 0). If the T3.TCR.ARDID is one then the T3.TCR.TRDI register bit controls this bit. If the RDI is generated automatically (T3.TCR.ARDID=0), the X-bits are set to zero when one or more of the indicated alarm conditions is present, and set to one when all of the indicated alarm conditions are absent. Automatically setting RDI on LOS, SEF, LOF, or AIS is individually programmable (on or off). The P-bits (P1 and P2) are both overwritten with the calculated payload parity from the previous DS3 frame. The payload parity is calculated by performing modulo 2 addition of all of the payload bits after all frame processing has been completed. P-bit generation is programmable (on or off). The P-bits will be generated if either P-bit generation is enabled or frame generation is enabled. If C-bit generation is enabled (T3.TCR.CBGD), the bit C11 is overwritten with an alternating one zero pattern, and all of the other C-bits (CXY) are overwritten with zeros. If C-bit generation is disabled, then all of the C-bit timeslots (CXY) will be treated as payload data, and passed through. C-bit generation is programmable (on or off). Note: Overhead insertion may still overwrite the C-bit time slots even if C-bit generation is disabled. Once all of the DS3 overhead bits have been overwritten, the data stream is passed on to error insertion. If frame generation is disabled, the incoming DS3 signal is passed on directly to error insertion. Frame generation is programmable (on or off). Note: P-bit generation may still be performed even if frame generation is disabled. 10.10.6.3 Transmit M23 DS3 Error Insertion Error insertion inserts various types of errors into the different DS3 overhead bits. The types of errors that can be inserted are framing errors and P-bit parity errors. The framing error insertion mode is programmable (F-bit, M-bit, SEF, or OOMF). An F-bit error is a single subframe alignment bit (FXY) error. An M-bit error is a single multiframe alignment bit (M1, M2, or M3) error. An SEF error is an error in all the sub-frame alignment bits in a sub-frame (FX1, FX2, FX3, and FX4). An OOMF error is a single multiframe alignment bit (M1, M2, or M3) error in each of two consecutive DS3 frames. A P-bit parity error is generated by is inverting the value of the P-bits (P1 and P2) in a single DS3 frame. P-bit parity error(s) can be inserted one error at a time, or continuously. The P-bit parity error insertion mode (single or continuous) is programmable. Each error type (framing or P-bit parity) has a separate enable. Continuous error insertion mode inserts errors at every opportunity. Single error insertion mode inserts an error at the next opportunity when requested. The framing multi-error insertion modes (SEF or OOMF) insert the indicated number of error(s) at the next opportunities when requested; i.e., a single request will cause multiple errors to be inserts. The requests can be initiated by a register bit (TSEI) or by the manual error insertion input (TMEI). The error insertion request source (register or input) is programmable. The insertion of each particular error type is individually enabled. Once all error insertion has been performed, the data stream is passed on to overhead insertion. 10.10.6.4 Transmit M23 DS3 Overhead Insertion Overhead insertion can insert any (or all) of the DS3 overhead bits into the DS3 frame. The DS3 overhead bits X1, X2, P1, P2, MX, FXY, and CXY can be sourced from the transmit overhead interface (TOHCLK, TOH, TOHEN, and TOHSOF). The P-bits (P1 and P2) are received as an error mask (modulo 2 addition of the input bit and the internally generated bit). The DS3 overhead insertion is fully controlled by the transmit overhead interface. If the transmit overhead data enable signal (TOHEN) is driven high, then the bit on the transmit overhead signal (TOH) is inserted into the output data stream. Insertion of bits using the TOH signal overwrites internal overhead insertion. 172 DS3181/DS3182/DS3183/DS3184 10.10.6.5 Transmit M23 DS3 AIS/Idle Generation M23 DS3 AIS/Idle generation overwrites the data stream with AIS or an Idle signal. If transmit Idle is enabled, the data stream payload is forced to an 1100 pattern with two ones immediately following each DS3 overhead bit. M1, M2, and M3 bits are overwritten with the values zero, one, and zero (010) respectively. FX1, FX2, FX3, and FX4 bits are overwritten with the values one, zero, zero, and one (1001) respectively. X1 and X2 are overwritten with 11.. P1 and P2 are overwritten with the calculated payload parity from the previous output DS3 frame. And, C31, C32, and C33 are overwritten with 000. If transmit AIS is enabled, the data stream payload is forced to a 1010 pattern with a one immediately following each DS3 overhead bit. M1, M2, and M3 bits are overwritten with the values zero, one, and zero (010) respectively. FX1, FX2, FX3, and FX4 bits are overwritten with the values one, zero, zero, and one (1001) respectively. X1 and X2 are overwritten with 11. P1 and P2 are overwritten with the calculated payload parity from the previous DS3 frame. And, CX1, CX2, and CX3 are overwritten with 000. AIS will overwrite a transmit Idle signal. 10.10.6.5.1 Receive M23 DS3 Frame Format The DS3 frame format is shown in Figure 10-40. The X1 and X2 are the Remote Defect Indication (RDI) bits (also referred to as the far-end SEF/AIS bits). P1 and P2 are the parity bits used for line error monitoring. M1, M2, and M3 are the multiframe alignment bits that define the multiframe boundary. FXY are the sub-frame alignment bits that define the sub-frame boundary. Note: Both the M-bits and F-bits define the DS3 frame boundary. C11 is the Application Identification Channel (AIC). CX1, CX2, and CX3 are the stuff control bits for tributary #X. 10.10.6.5.2 Receive M23 DS3 Overhead Extraction Overhead extraction extracts all of the DS3 overhead bits from the M23 DS3 frame. All of the DS3 overhead bits X1, X2, P1, P2, MX, FXY, and CXY are output on the receive overhead interface (ROH, ROHSOF, and ROHCLK). The P1 and P2 bits are output as an error indication (modulo 2 addition of the calculated parity and the bit). In addition, the Application Identification Channel (AIC) is extracted from the C11 bit and stored in a register. The AIC is set to one (C-bit format) if the C11 bit is set to one in 31 consecutive multiframes. The AIC is set to zero (M23 format) if the C11 bit is set to zero in four of the last 31 consecutive multiframes. Note: The stored AIC bit must not change when a LOS, OOF, or AIS condition is present. 10.10.6.5.3 Receive DS3 Downstream AIS Generation Downstream DS3 AIS (all `1's) can be automatically generated on an OOF, LOS, or AIS condition or manually inserted. If automatic downstream AIS is enabled, downstream AIS is inserted when an LOS or AIS condition is declared, or no earlier than 2.25 ms and no later than 2.75 ms after an OOF condition is declared. Automatic downstream AIS is programmable (on or off). If manual downstream AIS insertion is enabled, downstream AIS is inserted. Manual downstream AIS insertion is programmable (on or off). Downstream AIS is removed when all OOF, LOS, and AIS conditions are terminated and manual downstream AIS insertion is disabled. 173 DS3181/DS3182/DS3183/DS3184 10.10.7 G.751 E3 Framer/Formatter 10.10.7.1 Transmit G.751 E3 Frame Processor The G.751 E3 frame format is shown in Figure 10-43. FAS is the Frame Alignment Signal. A is the Alarm indication bit used to indicate the presence of an alarm to the remote terminal equipment. N is the National use bit reserved for national use. Figure 10-43. G.751 E3 Frame Format FAS A N 4 Rows 1524 Bit Payload 384 bits 10.10.7.2 Transmit G.751 E3 Frame Generation G.751 E3 frame generation receives the incoming payload data stream, and overwrites the entire E3 overhead bit locations. The first 10 bits of the frame are overwritten with the frame alignment signal (FAS), which has a value of 1111010000b. The 11th bit of the frame is overwritten with the alarm indication (A) bit. The A bit can be generated automatically, sourced from the transmit FEAC controller, set to one, or set to zero. The A bit source is programmable (automatic, FEAC, 1, or 0). If the A bit is generated automatically, it is set to one when one or more of the indicated alarm conditions is present, and set to zero when all of the indicated alarm conditions are absent. Automatically setting RDI on LOS, LOF, or AIS is individually programmable (on or off). The twelfth bit of the frame is overwritten with the national use (N) bit. The N bit can be sourced from the transmit FEAC controller, sourced from the transmit HDLC overhead controller, set to one, or set to zero. The N bit source is programmable (FEAC, HDLC, 1, or 0). Note: The FEAC controller will source one bit per frame regardless of whether the A bit only, the N bit only, or both are programmed to be sourced from the FEAC controller. Once all of the E3 overhead bits have been overwritten, the data stream is passed on to error insertion. If frame generation is disabled, the incoming E3 signal is passed on directly to error insertion. Frame generation is programmable (on or off). 10.10.7.3 Transmit G.751 E3 Error Insertion Error insertion inserts framing errors into the frame alignment signal (FAS). The type of error(s) inserted into the FAS is programmable (errored FAS bit or errored FAS). An errored FAS bit is a single bit error in the FAS. An errored FAS is an error in all ten bits of the FAS (a value of 0000101111b is inserted in the FAS). Framing error(s) can be inserted one error at a time, or in four consecutive frames. The framing error insertion number (single or four) is programmable. Single error insertion mode inserts an error at the next opportunity when requested. The multi-error insertion mode inserts the indicated number of errors at the next opportunities when requested. That is, a single request will cause multiple errors to be inserted. The requests can be initiated by a register bit (TSEI) or by the manual error insertion input (TMEI). The error insertion initiation type (register or input) is programmable. The insertion of each particular error type is individually enabled. Once all error insertion has been performed, the data stream is passed on to overhead insertion. 174 DS3181/DS3182/DS3183/DS3184 10.10.7.4 Transmit G.751 E3 Overhead Insertion Overhead insertion can insert any (or all) of the E3 overhead bits into the E3 frame. The FAS, A bit, and N bit can be sourced from the transmit overhead interface (TOHCLK, TOH, TOHEN, and TOHSOF). The E3 overhead insertion is fully controlled by the transmit overhead interface. If the transmit overhead data enable signal (TOHEN) is driven high, then the bit on the transmit overhead signal (TOH) is inserted into the output data stream. Insertion of bits using the TOH signal overwrites internal overhead insertion. 10.10.7.5 Transmit G.751 E3 AIS Generation G.751 E3 AIS generation overwrites the data stream with AIS. If transmit AIS is enabled, the data stream (payload and E3 overhead) is forced to all ones. 10.10.7.6 Receive G.751 E3 Frame Processor The G.751 E3 frame format is shown in Figure 10-43. FAS is the Frame Alignment Signal. A is the Alarm indication bit used to indicate the presence of an alarm to the remote terminal equipment. N is the National use bit reserved for national use. 10.10.7.6.1 Receive G.751 E3 Framing G.751 E3 framing determines the G.751 E3 frame boundary. The frame boundary is found by identifying the frame alignment signal (FAS), which has a value of 1111010000b. The framer is an off-line framer that updates the data path frame counters when an out of frame (OOF) condition has been detected. The use of an off-line framer reduces the average time required to reframe, and reduces data loss caused by burst error. The G.751 E3 framer checks each bit position for the FAS. The frame boundary is set once the FAS is identified. Since, the FAS check is performed one bit at a time, up to 1536 checks may be needed to find the frame boundary. The data path frame counters are updated if an error free FAS is received for two additional frames, and an OOF condition is present, or if a manual frame re-synchronization has been initiated. 10.10.7.6.2 Receive G.751 E3 Performance Monitoring Performance monitoring checks the E3 frame for alarm conditions. The alarm conditions detected are OOF, LOF, COFA, LOS, AIS, RUA1, and RAI. An Out Of Frame (OOF) condition is declared when four consecutive frame alignment signals (FAS) contain one or more errors or at the next FAS check when a manual reframe is requested. An OOF condition is terminated when three consecutive FASs are error-free or the G.751 E3 framer updates the data path frame counters. A Loss Of Frame (LOF) condition is declared by the LOF integration counter when it has been active for a total of T ms. The LOF integration counter is active (increments count) when an OOF condition is present, it is inactive (holds count) when an OOF condition is absent, and it is reset when an OOF condition is absent for T continuous ms. T is programmable (0, 1, 2, or 3). An LOF condition is terminated when an OOF condition is absent for T continuous ms. A Change Of Frame Alignment (COFA) is declared when the G.751 E3 framer updates the data path frame counters with a frame alignment that is different from the current data path frame alignment. A Loss Of Signal (LOS) condition is declared when the HDB3 encoder is active, and it declares a LOS condition. A LOS condition is terminated when the HDB3 encoder is inactive, or it terminates a LOS condition. An Alarm Indication Signal (AIS) condition is declared when 4 or less zeros are detected in each of two consecutive frame periods. An AIS condition is terminated when 5 or more zeros are detected in each of two consecutive frame periods. A Receive Unframed All 1's (RUA1) condition is declared if in each of 4 consecutive 2047 bit windows, five or less zeros are detected and an OOF condition is continuously present. A RUA1 condition is terminated if in each of 4 consecutive 2047-bit windows, six or more zeros are detected or an OOF condition is continuously absent. A Remote Alarm Indication (RAI) condition is declared when four consecutive frames are received with the A bit (first bit after the FAS) set to one. An RAI condition is terminated when four consecutive frames are received with the A bit set to zero. Only framing errors are accumulated. Framing errors are determined by comparing the FAS to its expected value. The type of framing errors accumulated is programmable (OOF, bit, or word). An OOF error increments the count whenever an OOF condition is first detected. A bit error increments the count once for each bit in the FAS that does 175 DS3181/DS3182/DS3183/DS3184 not match its expected value (up to 10 per frame. A word error increments the count once for each FAS that does not match its expected value (up to 1 per frame). The receive alarm indication (RAI) signal is high when one or more of the indicated alarm conditions is present, and low when all of the indicated alarm conditions are absent. Setting the receive alarm indication on LOS, OOF, LOF, or AIS is individually programmable (on or off). 10.10.7.6.3 Receive G.751 E3 Overhead Extraction Overhead extraction extracts all of the E3 overhead bits from the G.751 E3 frame. The FAS, A bit, and N bit are output on the receive overhead interface (ROH, ROHSOF, and ROHCLK). In addition, the A bit is integrated and stored in a register along with a change indication, and can be output over the receive FEAC controller. The N bit is integrated and stored in a register along with a change indication, is sent to the receive HDLC overhead controller, and can also be sent to the receive FEAC controller. The bit sent to the receive FEAC controller is programmable (A or N). 10.10.7.6.4 Receive G.751 Downstream AIS Generation Downstream G.751 E3 AIS can be automatically generated on an OOF, LOS, or AIS condition or manually inserted. If automatic downstream AIS is enabled, downstream AIS is inserted when a LOS, OOF, or AIS condition is declared. Automatic downstream AIS is programmable (on or off). If manual downstream AIS insertion is enabled, downstream AIS is inserted. Manual downstream AIS insertion is programmable (on or off). Downstream AIS is removed when all OOF, LOS, and AIS conditions are terminated and manual downstream AIS insertion is disabled. RPDT will be forced to all ones during downstream AIS. 10.10.8 G.832 E3 Framer/Formatter 10.10.8.1 Transmit G.832 E3 Frame Processor The G.832 E3 frame format is shown in Figure 10-44. Figure 10-44. G.832 E3 Frame Format FA1 FA2 EM TR MA NR 530 Byte Payload GC 59 Columns 176 9 Rows DS3181/DS3182/DS3183/DS3184 Figure 10-45. MA Byte Format MSB 1 LSB 8 RDI REI SL SL SL MI MI TM RDI - Remote Defect Indicator REI - Remote Error Indicator SL - Signal Label MI - Multi-frame Indicator TM - Timing Marker Table 10-36 shows the function of each overhead bit in the DS3 Frame. Table 10-36. G.832 E3 Frame Overhead Bit Definitions BYTE FA1, FA2 DEFINITION Frame Alignment bytes EM Error Monitoring byte TR Trail Trace byte MA Maintenance and Adaptation byte NR Network Operator byte GC General-Purpose Communication Channel byte FA1 and FA2 are the Frame Alignment bytes. EM is the Error Monitoring byte used for path error monitoring. TR is the Trail Trace byte used for end-to-end connectivity verification. MA is the Maintenance and Adaptation byte used for far-end path status and performance monitoring. NR is the Network Operator byte allocated for network operator maintenance purposes. GC is the General-Purpose Communications Channel byte allocated for user communications purposes. 10.10.8.2 Transmit G.832 E3 Frame Generation G.832 E3 frame generation receives the incoming payload data stream, and overwrites all of the E3 overhead byte locations. The first two bytes of the first row in the frame are overwritten with the frame alignment bytes FA1 and FA2, which have a value of F6h and 28h respectively. The first byte in the second row of the frame is overwritten with the EM byte which is a BIP-8 calculated over all of the bytes of the previous frame after all frame processing (frame generation, error insertion, overhead insertion, and AIS generation) has been performed. The first byte in the third row of the frame is overwritten with the TR byte which is input from the transmit trail trace controller. The first byte in the fourth row of the frame is overwritten with the MA byte (see Figure 10-45), which consists of the RDI bit, REI bit, payload type, multiframe indicator, and timing source indicator. The RDI (remote defect indicator) bit can be generated automatically, set to one, or set to zero. The RDI source is programmable (automatic, 1, or 0). If the RDI is generated automatically, it is set to one when one or more of the indicated alarm conditions are detected on the receive side, and set to zero when all of the indicated alarm conditions are absent. Automatically setting RDI on LOS, LOF, or AIS is individually programmable (on or off). The REI (remote error indicator) bit can be generated automatically or inserted from a register bit (E3G832.TCR.TFEBE). The REI source is programmable (automatic or register bit). If REI is generated 177 DS3181/DS3182/DS3183/DS3184 automatically, it is set to one when at least one parity error has been detected on the receive side during the previous frame. The payload type is sourced from a register. The three register bits are inserted in the third, fourth, and fifth bits of the MA byte in each frame. The multiframe indicator and timing marker bits can be directly inserted from a 3-bit register or generated from a 4bit register. The multiframe indicator and timing marker insertion type is programmable (direct or generated). When the multiframe indicator and timing marker bits are directly inserted, the three register bits are inserted in the last three bits of the MA byte in each frame. When the multiframe indicator and timing marker bits are generated, the four timing source indicator bits are transferred in a four-frame multiframe, MSB first. The multiframe indicator bits (sixth and seventh bits of the MA byte) identify the phase of the multiframe (00, 01, 10, or 11), and the timing marker bit (eighth bit of the MA byte) contains the corresponding timing source indicator bit (TMABR register bits TTI3, TTI2, TTI1, or TTI0 respectively). Note: The initial phase of the multiframe is arbitrarily chosen. The first byte in the fifth row of the frame is overwritten with the NR byte which can be sourced from a register, from the transmit FEAC controller, or from the transmit HDLC controller. The NR byte source is programmable (register, FEAC, or HDLC). Note: The HDLC controller will source eight bits per frame period regardless of whether the NR byte only, GC byte only, or both are programmed to be sourced from the HDLC controller. The first byte in the sixth row of the frame is overwritten with the GC byte which can be sourced from a register or from the transmit HDLC controller. The GC byte source is programmable (register or HDLC). Once all of the E3 overhead bytes have been overwritten, the data stream is passed on to error insertion. If frame generation is disabled, the incoming E3 signal is passed on directly to error insertion. Frame generation is programmable (on or off). 10.10.8.3 Transmit G.832 E3 Error Insertion Error insertion inserts various types of errors into the different E3 overhead bytes. The types of errors that can be inserted are framing errors, BIP-8 parity errors, and Remote Error Indication (REI) errors. The type of framing error(s) inserted is programmable (errored frame alignment bit or errored frame alignment word). A frame alignment bit error is a single bit error in the frame alignment word (FA1 or FA2). A frame alignment word error is an error in all 16 bits of the frame alignment word (the values 09h and D7h are inserted in the FA1 and FA2 bytes, respectively). Framing error(s) can be inserted one error at a time, or four consecutive frames. The framing error insertion mode (single or four) is programmable. The type of BIP-8 error(s) inserted is programmable (errored BIP-8 bit or errored BIP-8 byte). An errored BIP-8 bit is inverting a single bit error in the EM byte. An errored BIP-8 byte is inverting all eight bits in the EM byte. BIP-8 error(s) can be inserted one error at a time, or continuously. The BIP-8 error insertion mode (single or continuous) is programmable. An REI error is generated by forcing the second bit of the MA byte to a one. REI error(s) can be inserted one error at a time, or continuously. The REI error insertion mode (single or continuous) is programmable. Each error type (framing, BIP-8, or REI) has a separate enable. Continuous error insertion mode inserts errors at every opportunity. Single error insertion mode inserts an error at the next opportunity when requested. The framing multi-error insertion mode inserts the indicated number of errors at the next opportunities when requested. I.e., a single request will cause multiple errors to be inserted. The requests can be initiated by a register bit (TSEI) or by the manual error insertion input (TMEI). The error insertion request source (register or input) is programmable. The insertion of each particular error type is individually enabled. Once all error insertion has been performed, the data stream is passed on to overhead insertion. 10.10.8.4 Transmit G.832 E3 Overhead Insertion Overhead insertion can insert any (or all) of the E3 overhead bytes into the E3 frame. The E3 overhead bytes FA1, FA2, EM, TR, MA, NR, and GC can be sourced from the transmit overhead interface (TOHCLK, TOH, TOHEN, and TOHSOF). The EM byte is sourced as an error mask (modulo 2 addition of the input EM byte and the generated EM byte). The E3 overhead insertion is fully controlled by the transmit overhead interface. If the transmit overhead data enable signal (TOHEN) is driven high, then the bit on the transmit overhead signal (TOH) is inserted into the output data stream. Insertion of bits using the TOH signal overwrites internal overhead insertion. 178 DS3181/DS3182/DS3183/DS3184 10.10.8.5 Transmit G.832 E3 AIS Generation G.832 E3 AIS generation overwrites the data stream with AIS. If transmit AIS is enabled, the data stream (payload and E3 overhead) is forced to all ones. 10.10.8.6 Receive G.832 E3 Frame Processor The G.832 E3 frame format is shown in Figure 10-44. FA1 and FA2 are the Frame Alignment bytes. EM is the Error Monitoring byte used for path error monitoring. TR is the Trail Trace byte used for end-to-end connectivity verification. MA is the Maintenance and Adaptation byte used for far-end path status and performance monitoring (See Figure 10-45). NR is the Network Operator byte allocated for network operator maintenance purposes. GC is the General-Purpose Communications Channel byte allocated for user communications purposes. 10.10.8.7 Receive G.832 E3 Framing G.832 E3 framing determines the G.832 E3 frame boundary. The frame boundary is found by identifying the frame alignment bytes FA1 and FA2, which have a value of F6h and 28h, respectively. The framer is an off-line framer that updates the data path frame counters when an out of frame (OOF) condition has been detected. The use of an off-line framer reduces the average time required to reframe, and reduces data loss caused by burst error. The G.832 E3 framer checks each bit position for the frame alignment word (FA1 and FA2). The frame boundary is set once the frame alignment word is identified. Since, the frame alignment word check is performed one bit at a time; up to 4296 checks may be needed to find the frame boundary. The data path frame counters are updated if an error free frame alignment word is received for two additional frames, and an OOF condition is present. 10.10.8.8 Receive G.832 E3 Performance Monitoring Performance monitoring checks the E3 frame for alarm conditions and errors. The alarm conditions detected are OOF, LOF, COFA, LOS, AIS, RUA1, and RDI. The errors accumulated are framing, parity, and Remote Error Indication (REI) errors. An Out Of Frame (OOF) condition is declared when four consecutive frame alignment words (FA1 and FA2) contain one or more errors, when 986 or more frames out of 1,000 frames has a BIP-8 block error, or at the next framing word check when a manual reframe is requested. An OOF condition is terminated when three consecutive frame alignment words (FA1 and FA2) are error free or the G.832 E3 framer updates the data path frame counters. A Loss Of Frame (LOF) condition is declared by the LOF integration counter when it has been active for a total of T ms. The LOF integration counter is active (increments count) when an OOF condition is present, it is inactive (holds count) when an OOF condition is absent, and it is reset when an OOF condition is absent for T continuous ms. T is programmable (0, 1, 2, or 3). An LOF condition is terminated when an OOF condition is absent for T continuous ms. A Change Of Frame Alignment (COFA) is declared when the G.832 E3 framer updates the data path frame counters with a frame alignment that is different from the current data path frame alignment. A Loss Of Signal (LOS) condition is declared when the HDB3 encoder is active, and it declares a LOS condition. A LOS condition is terminated when the HDB3 encoder is inactive, or it terminates a LOS condition. An Alarm Indication Signal (AIS) condition is declared when 7 or less zeros are detected in each of two consecutive frame periods that do not contain a frame alignment word. An AIS condition is terminated when 8 or more zeros are detected in each of two consecutive frame periods. A Receive Unframed All 1's (RUA1) condition is declared if in each of 4 consecutive 2047 bit windows, five or less zeros are detected and an OOF condition is continuously present. A RUA1 condition is terminated if in each of 4 consecutive 2047-bit windows, six or more zeros are detected or an OOF condition is continuously absent. A Remote Defect Indication (RDI) condition is declared when four consecutive frames are received with the RDI bit (first bit of MA byte) set to one. An RDI condition is terminated when four consecutive frames are received with the RDI bit set to zero. Three types of errors are accumulated, framing, parity, and Remote Error Indication (REI) errors. Framing errors are determined by comparing FA1 and FA2 to their expected values. The type of framing errors accumulated is programmable (OOF, bit, byte, or word). An OOF error increments the count whenever an OOF condition is first detected. A bit error increments the count once for each bit in FA1 and each bit in FA2 that does not match its expected value (up to 16 per frame). A byte error increments the count once for each FA byte (FA1 or FA2) that does not match its expected value (up to 2 per frame). A word error increments the count once for each FA word (both FA1 and FA2) that does not match its expected value (up to 1 per frame). 179 DS3181/DS3182/DS3183/DS3184 Parity errors are determined by calculating the BIP-8 (8-Bit Interleaved Parity) of the current E3 frame (overhead and payload bytes), and comparing the calculated BIP-8 to the EM byte in the next frame. The type of parity errors accumulated is programmable (bit or block). A bit error increments the count once for each bit in the EM byte that does not match the corresponding bit in the calculated BIP-8 (up to 8 per frame). A block error increments the count if any bit in the EM byte does not match the corresponding bit in the calculated BIP-8 (up to 1 per frame). REI errors are determined by the REI bit (second bit of MA byte). A one indicates an error and a zero indicates no errors. The receive defect indication (RDI) alarm is transmitted when the receive framer detects one or more of the indicated alarm conditions. The RDI bit is not transmitted when all of the indicated alarm conditions are absent. The RDI bit in the MA byte of the G.832 overhead is set high in the transmit formatter to transmit the alarm. Setting the receive defect indication on LOS, OOF, LOF, or AIS is individually programmable (on or off). The receive error indication (REI) bit of the MA byte in the transmit frame will transition from low to high once for each frame in which a parity error is detected by the receive framer. 10.10.8.9 Receive G.832 E3 Overhead Extraction Overhead extraction extracts all of the E3 overhead bytes from the G.832 E3 frame. All of the E3 overhead bytes FA1, FA2, EM, TR, MA, NR, and GC are output on the receive overhead interface (ROH, ROHSOF, and ROHCLK). The EM byte is output as an error indication (modulo 2 addition of the calculated BIP-8 and the EM byte. The TR byte is sent to the receive trail trace controller. The payload type (third, fourth, and fifth bits of the MA byte) is integrated and stored in a register with change and unstable indications. The integrated received payload type is also compared against an expected payload type. If the received and expected payload types do not match (See Table 10-37), a mismatch indication is set. Table 10-37. Payload Label Match Status EXPECTED 000 RECEIVED 000 STATUS Match 000 001 Mismatch 000 XXX Mismatch 001 000 Mismatch 001 001 Match 001 XXX Match XXX 000 Mismatch XXX 001 Match XXX XXX Match XXX YYY Mismatch XXX and YYY equal any value other than 000 or 001; XXX YYY The multiframe indicator and timing marker bits (sixth, seventh, and eighth bits of the MA byte) can be integrated and stored in three register bits or extracted, integrated, and stored in four register bits. The bits (three or four) are stored with a change indication. The multiframe indicator and timing marker storage type is programmable (integrated or extracted). When the multiframe indicator and timing marker bits are integrated, the last three bits of the MA byte are integrated and stored in three register bits. When the multiframe indicator and timing marker bits are extracted, four timing source indicator bits are transferred in a four-frame multiframe, MSB first. The multiframe indicator bits (sixth and seventh bits of the MA byte) identify the phase of the multiframe (00, 01, 10, or 11). The timing marker bit (eighth bit of the MA byte) contains the timing source indicator bit indicated by the multiframe indicator bits (first, second, third, or fourth bit, respectively). The four timing source indicator bits are extracted from the multiframe, integrated, and stored in four register bits with unstable and change indications. 180 DS3181/DS3182/DS3183/DS3184 The NR byte is integrated and stored in a register along with a change indication, it is sent to the receive FEAC controller, and it can be sent to the receive HDLC controller. The byte sent to the receive HDLC controller is programmable (NR or GC). The GC byte is integrated and stored in a register along with a change indication, and can be sent to the receive HDLC controller. The byte sent to the receive HDLC controller is programmable (NR or GC). 10.10.8.10 Receive G.832 Downstream AIS Generation Downstream G.832 E3 AIS can be automatically generated on an OOF, LOS, or AIS condition or manually inserted. If automatic downstream AIS is enabled, downstream AIS is inserted when a LOS, OOF, or AIS condition is declared. Automatic downstream AIS is programmable (on or off). If manual downstream AIS insertion is enabled, downstream AIS is inserted. Manual downstream AIS insertion is programmable (on or off). Downstream AIS is removed when all OOF, LOS, and AIS conditions are terminated and manual downstream AIS insertion is disabled. RPDT will be forced to all ones during downstream AIS. 10.10.9 Clear-Channel Frame Processor 10.10.9.1 Transmit Clear-Channel AIS Generation Clear-channel AIS generation overwrites the data stream with AIS. If transmit AIS is enabled, the data stream (payload) is forced to all ones. 10.10.9.2 Receive Clear-Channel Performance Monitoring Performance monitoring checks the clear-channel signal for alarm conditions. The alarm conditions detected are LOS and RUA1. A Loss Of Signal (LOS) condition is declared when the B3ZS/HDB3 encoder is active, and it declares a LOS condition. A LOS condition is terminated when the B3ZS/HDB3 encoder is inactive, or it terminates a LOS condition. A Receive Unframed All 1's (RUA1) condition is declared if in each of 4 consecutive 2047 bit windows, five or less zeros are detected. A RUA1 condition is terminated if in each of 4 consecutive 2047 bit windows, six or more zeros are detected. 10.10.9.3 Receive Clear-Channel Downstream AIS Generation Downstream clear-channel AIS can be automatically generated on a LOS condition or manually inserted. If automatic downstream AIS is enabled, downstream AIS is inserted when a LOS condition is declared. Automatic downstream AIS is programmable (on or off). If manual downstream AIS insertion is enabled, downstream AIS is inserted. Manual downstream AIS insertion is programmable (on or off). Downstream AIS is removed when all LOS conditions are terminated and manual downstream AIS insertion is disabled. All bits will be forced to ones during downstream AIS. 10.11 HDLC Overhead Controller 10.11.1 General Description The DS318x devices contain built-in HDLC controllers (one per port) with 256-byte FIFOs for insertion/extraction of DS3 PMDL, G.751 Sn bit and G.832 NR/GC bytes and PLCP NR/GC bytes. The HDLC Overhead Controller demaps HDLC overhead packets from the DS3/E3 data stream in the receive direction and maps HDLC packets into the DS3/E3 data stream in the transmit direction. The receive direction performs packet processing and stores the packet data in the FIFO. It removes packet data from the FIFO and outputs the packet data to the microprocessor via the register interface. The transmit direction inputs the packet data from the microprocessor via the register interface and stores the packet data in the FIFO. It removes the packet data from the FIFO and performs packet processing. The bits in a byte are received MSB first, LSB last. When they are output serially, they are output MSB first, LSB last. The bits in a byte in an incoming signal are numbered in the order they are received, 1 (MSB) to 8 (LSB). However, when a byte is stored in a register, the MSB is stored in the lowest numbered bit (0), and the LSB is stored in the highest numbered bit (7). This is to differentiate between a byte in a register and the corresponding byte in a signal. 181 DS3181/DS3182/DS3183/DS3184 See Figure 10-46 for the location of HDLC controllers within the DS318x devices. Figure 10-46. HDLC Controller Block Diagram TAIS TUA1 DS3/E3 Receive LIU B3ZS/ HDB3 Decoder TX BERT HDLC Clock Rate Adapter DS3 / E3 Receive Framer IEEE P1149.1 JTAG Test Access Port RX BERT RX FRAC/ PLCP UA1 GEN Tx FIFO Tx Packet Processor System Interface Trail Trace Buf f er PLB FEAC TX FRAC/ PLCP Tx Cell Processor SLB DLB LLB DS3/E3 Transmit LIU ALB DS3 / E3 Transmit Formatter B3ZS/ HDB3 Encoder Rx Packet Processor Rx Cell Processor Rx FIFO Microprocessor Interface 10.11.2 Features * * * * * * Programmable inter-frame fill - The inter-frame fill between packets can be all 1's or flags. Programmable FCS generation/monitoring - A FCS-16 can be generated and appended to the end of the packet, and the FCS can be checked and removed from the end of the packet. Programmable bit reordering - The packet data can be can be output MSB first or LSB first from the FIFO. Programmable data inversion - The packet data can be inverted immediately after packet processing on the transmit, and immediately before packet processing on the receive. Fully independent transmit and receive paths Fully independent Line side and register interface timing - The data storage can be read from or written to via the microprocessor interface while all line side clocks and signals are inactive, and read from or written to via the line side while all microprocessor interface clocks and signals are inactive. 10.11.3 Transmit FIFO The Transmit FIFO block contains memory for 256 bytes of data with data status information and controller circuitry for reading and writing the memory. The Transmit FIFO controller functions include filling the memory, tracking the memory fill level, maintaining the memory read and write pointers, and detecting memory overflow and underflow conditions. The Transmit FIFO receives data and status from the microprocessor interface, and stores the data along with the data status information in memory. The Transmit Packet Processor reads the data and data status information from the Transmit FIFO. The Transmit FIFO also outputs FIFO fill status (empty/data storage available/full) via the microprocessor interface. All operations are byte based. The Transmit FIFO is considered empty when its memory does not contain any data. The Transmit FIFO is considered to have data storage available when its memory has a programmable number of bytes or more available for storage. The Transmit FIFO is considered full when it does not have any space available for storage. The Transmit FIFO accepts data from the register interface until full. If the Transmit FIFO is written to while the FIFO is full, the write is ignored, and a FIFO overflow condition is declared. The Transmit Packet Processor reads the Transmit FIFO. If the Transmit Packet Processor attempts to read the Transmit FIFO while it is empty, a FIFO underflow condition is declared. 10.11.4 Transmit HDLC Overhead Processor The Transmit HDLC Overhead Processor accepts data from the Transmit FIFO, performs bit reordering, FCS processing, stuffing, packet abort sequence insertion, and inter-frame padding. A byte is read from the Transmit FIFO with a packet end status. When a byte is marked with a packet end indication, the output data stream will be padded with FFh and marked with a FIFO empty indication if the Transmit 182 DS3181/DS3182/DS3183/DS3184 FIFO contains less than two bytes or transmit packet start is disabled. Transmit packet start is programmable (on or off). When the Transmit Packet Processor reads the Transmit FIFO while it is empty, the output data stream is marked with an abort indication. Once the Transmit FIFO is empty, the output data stream will be padded with interframe fill until the Transmit FIFO contains two or more bytes of data and transmit packet start is enabled. Bit reordering changes the bit order of each byte. If bit reordering is disabled, the outgoing 8-bit data stream DT[1:8] with DT[1] being the MSB and DT[8] being the LSB is input from the Transmit FIFO with the MSB in TFD[0] and the LSB in TFD[7] of the transmit FIFO data TFD[7:0]. If bit reordering is enabled, the outgoing 8-bit data stream DT[1:8] is input from the Transmit FIFO with the MSB in TFD[7] and the LSB in TFD[0] of the transmit FIFO data TFD[7:0]. DT[1] is the first bit transmitted on the outgoing data stream. FCS processing calculates a FCS and appends it to the packet. FCS calculation is a CRC-16 calculation over the entire packet. The polynomial used for the CRC-16 is x16 + x12 + x5 + 1. The CRC-16 is inverted after calculation, and appended to the packet. For diagnostic purposes, a FCS error can be inserted. This is accomplished by appending the calculated CRC-16 without inverting it. FCS error insertion is programmable (on or off). When FCS processing is disabled, the packet is output without appending a FCS. FCS processing is programmable (on or off). Stuffing inserts control data into the packet to prevent packet data from mimicking flags. Stuffing is halted during FIFO empty periods. The 8-bit parallel data stream is multiplexed into a serial data stream, and bit stuffing is performed. Bit stuffing consists of inserting a '0' directly following any five contiguous '1's. Stuffing is performed from a packet start until a packet end. Inter-frame padding inserts inter-frame fill between the packet start and end flags when the FIFO is empty. The inter-frame fill can be flags or '1's. If the inter-frame fill is flags, flags (minimum two) are inserted until a packet start is received. If the inter-frame fill is all '1's, an end flag is inserted, `1's are inserted until a packet start is received, and a start flag is inserted after the `1's. The number of '1's between the end flag and start flag may not be an integer number of bytes, however, the inter-frame fill will be at least 15 consecutive '1's. If the FIFO is not empty between a packet end and a packet start, then two flags are inserted between the packet end and packet start. The inter-frame padding type is programmable (flags or `1's). Packet abort insertion inserts a packet abort sequences as necessary. If a packet abort indication is detected, a packet abort sequence is inserted and inter-frame padding is done until a packet start is detected. The abort sequence is FFh. Once all packet processing has been completed, the datastream is inserted into the DS3/E3 datastream at the proper locations. If transmit data inversion is enabled, the outgoing data is inverted after packet processing is performed. Transmit data inversion is programmable (on or off). 10.11.5 Receive HDLC Overhead Processor The Receive HDLC Overhead Packet Processor accepts data from the DS3/E3 Framer or the PLCP Framer and performs packet delineation, inter-frame fill filtering, packet abort detection, destuffing, FCS processing, and bit reordering. If receive data inversion is enabled, the incoming data is inverted before packet processing is performed. Receive data inversion is programmable (on or off). Packet delineation determines the packet boundary by identifying a packet start flag. Each time slot is checked for a flag sequence (7Eh). Once a flag is found, if it is identified as a start or end flag, and the packet boundary is set. There may be a single flag (both end and start) between packets, there may be an end flag and a start flag with a shared zero (011111101111110) between packets, there may be an end flag and a start flag (two flags) between packets, or there may be an end flag, inter-frame fill, and a start flag between packets. The flag check is performed one bit at a time. Inter-frame fill filtering removes the inter-frame fill between a start flag and an end flag. All inter-frame fill is discarded. The inter-frame fill can be flags (01111110) or all '1's. When inter-frame fill is all `1's, the number of '1's between the end flag and the start flag may not be an integer number of bytes. When inter-frame fill is flags, the number of bits between the end flag and the start flag will be an integer number of bytes (flags). Any time there is less than 16 bits between two flags, the data will be discarded. Packet abort detection searches for a packet abort sequence. Between a packet start flag and a packet end flag, if an abort sequence is detected, the packet is marked with an abort indication, and all subsequent data is discarded until a packet start flag is detected. The abort sequence is seven consecutive ones. 183 DS3181/DS3182/DS3183/DS3184 Packet abort detection searches for a packet abort sequence. Between a packet start flag and a packet end flag, if an abort sequence is detected, the packet is marked with an abort indication, and all subsequent data is discarded until a packet start flag is detected. The abort sequence is seven consecutive ones. Destuffing removes the extra data inserted to prevent data from mimicking a flag or an abort sequence. After a start flag is detected, destuffing is performed until an end flag is detected. Destuffing consists of discarding any '0' that directly follows five contiguous '1's. After destuffing is completed, the serial bit stream is demultiplexed into an 8-bit parallel data stream and passed on with packet start, packet end, and packet abort indications. If there is less than eight bits in the last byte, an invalid packet status is set, and the packet is tagged with an abort indication. FCS processing checks the FCS, discards the FCS bytes, and marks FCS erred packets. The FCS is checked for errors, and the last two bytes are removed from the end of the packet. If a FCS error is detected, the packet is marked with a FCS error indication. The HDLC CONTROLLER performs FCS-16 checking. FCS processing is programmable (on or off). If FCS processing is disabled, FCS checking is not performed, and all of the packet data is passed on. Bit reordering changes the bit order of each byte. If bit reordering is disabled, the incoming 8-bit data stream DT[1:8] with DT[1] being the MSB and DT[8] being the LSB is output to the Receive FIFO with the MSB in RFD[0] and the LSB in RFD[7] of the receive FIFO data RFD[7:0]. If bit reordering is enabled, the incoming 8-bit data stream DT[1:8] is output to the Receive FIFO with the MSB in RFD[7] and the LSB in RFD[0] of the receive FIFO data RFD[7:0]. DT[1] is the first bit received from the incoming data stream. Once all of the packet processing has been completed, The 8-bit parallel data stream is passed on to the Receive FIFO with packet start, packet end, and packet error indications. 10.11.6 Receive FIFO The Receive FIFO block contains memory for 256 bytes of data with data status information and controller circuitry for reading and writing the memory. The Receive FIFO Controller controls filling the memory, tracking the memory fill level, maintaining the memory read and write pointers, and detecting memory overflow and underflow conditions. The Receive FIFO accepts data and data status from the Receive Packet Processor and stores the data along with data status information in memory. The data is read from the receive FIFO via the microprocessor interface. The Receive FIFO also outputs FIFO fill status (empty/data available/full) via the microprocessor interface. All operations are byte based. The Receive FIFO is considered empty when it does not contain any data. The Receive FIFO is considered to have data available when there is a programmable number of bytes or more stored in the memory. The Receive FIFO is considered full when it does not have any space available for storage. The Receive FIFO accepts data from the Receive Packet Processor until full. If a packet start is received while full, the data is discarded and a FIFO overflow condition is declared. If any other packet data is received while full, the current packet being transferred is marked with an abort indication, and a FIFO overflow condition is declared. Once a FIFO overflow condition is declared, the Receive FIFO will discard incoming data until a packet start is received while the Receive FIFO has 16 or more bytes available for storage. If the Receive FIFO is read while the FIFO is empty, the read is ignored, and an invalid data indication given. 10.12 Trail Trace Controller 10.12.1 General Description Each port has a dedicated Trail Trace Buffer for E3-G.832 or DS3/E3 PLCP link management The Trail Trace Controller performs extraction and storage of the incoming G.832 or PLCP trail access point identifier in a 16-byte receive register. The Trail Trace Controller extracts/inserts E3-G.832 or PLCP trail access point identifiers using a 16-byte register (one for transmit, one for receive). (E3-G.832 and PLCP Framing are mutually exclusive; therefore one controller can be used for both.) The Trail Trace Controller demaps a 16-byte trail trace identifier from the E3-G.832 TR Byte of the overhead or PLCP datastream in the receive direction and maps a trace identifier into the E3-G.832 or PLCP datastream in the transmit direction. The receive direction inputs the trace ID data stream, performs trace ID processing, and stores the trace identifier data in the data storage using line timing. It removes trace identifier data from the data storage and outputs the 184 DS3181/DS3182/DS3183/DS3184 trace identifier data to the microprocessor via the microprocessor interface using register timing. The data is forced to all ones during LOS, LOF and AIS detection to eliminate false messages The transmit direction inputs the trace identifier data from the microprocessor via the microprocessor interface and stores the trace identifier data in the data storage using register timing. It removes the trace identifier data from the data storage, performs trace ID processing, and outputs the trace ID data stream. See Figure 10-47 for the location of the Trail Trace Controller with the DS318x devices. Figure 10-47. Trail Trace Controller Block Diagram TAIS TUA1 DS3/E3 Receive LIU TX BERT HDLC B3ZS/ HDB3 Decoder Clock Rate Adapter DS3 / E3 Receive Framer IEEE P1149.1 JTAG Test Access Port RX BERT RX FRAC/ PLCP UA1 GEN Tx FIFO Tx Packet Processor System Interface Trail Trace Buf f er PLB FEAC TX FRAC/ PLCP Tx Cell Processor SLB DLB LLB DS3/E3 Transmit LIU ALB DS3 / E3 Transmit Formatter B3ZS/ HDB3 Encoder Rx Packet Processor Rx Cell Processor Rx FIFO Microprocessor Interface 10.12.2 Features * * * * * * * * Programmable trail trace ID - The trail trace ID controller can be programmed to handle a 16-byte trail trace identifier (trail trace mode). Programmable transmit trace ID - All 16 bytes of the transmit trail trace identifier are programmable. Programmable receive expected trace ID - A 16-byte expected trail trace identifier can be programmed. Both a mismatch and unstable indication are provided. Programmable trace ID multiframe alignment - The transmit side can be programmed to perform trail trace multiframe alignment insertion. The receive side can be programmed to perform trail trace Multiframe synchronization. Programmable bit reordering - The trace identifier data can be output MSB first or LSB first from the data storage. Programmable data inversion - The trace identifier data can be inverted immediately after trace ID processing on the transmit side, and immediately before trail ID processing on the receive side. Fully independent transmit and receive sides Fully independent Line side and register interface timing - The data storage can be read from or written to via the microprocessor interface while all line side clocks and signals are inactive, and read from or written to via the line side while all microprocessor interface clocks and signals are inactive. 10.12.3 Functional Description The bits in a byte are received most significant bit (MSB) first and least significant bit (LSB) last. When they are output serially, they are output MSB first and LSB last. The bits in a byte in an incoming signal are numbered in the order they are received, 1 (MSB) to 8 (LSB). However, when a byte is stored in a register, the MSB is stored in the highest numbered bit (7), and the LSB is stored in the lowest numbered bit (0). This is to differentiate between a byte in a register and the corresponding byte in a signal. 185 DS3181/DS3182/DS3183/DS3184 10.12.4 Transmit Data Storage The Transmit Data Storage block contains memory for 16 bytes of data and controller circuitry for reading and writing the memory. The Transmit Data Storage controller functions include filling the memory and maintaining the memory read and write pointers. The Transmit Data Storage receives data from the microprocessor interface, and stores the data in memory. The Transmit Trace ID Processor reads the data from the Transmit Data Storage. The Transmit Data Storage contains the transmit trail trace identifier. Note: The contents of the transmit trail (path) trace identifier memory will be random data immediately after power-up, and will not change during a reset (RST or DRST low). 10.12.5 Transmit Trace ID Processor The Transmit Trace ID Processor accepts data from Transmit Data Storage, processes the data according to the Transmit Trace ID mode, and outputs the serial trace ID data stream. 10.12.6 Transmit Trail Trace Processing The Transmit Trail Trace Processing accepts data from the Transmit Data Storage performs bit reordering and multiframe alignment insertion. Bit reordering changes the bit order of each byte. If bit reordering is disabled, the outgoing 8-bit data stream DT[1:8] with DT[1] being the MSB and DT[8] being the LSB is input from the Transmit Data Storage with the MSB in TTD[7] and the LSB in TTD[0] of the transmit trace ID data TTD[7:0]. If bit reordering is enabled, the outgoing 8bit data stream DT[1:8] is input from the Transmit Data Storage with the MSB is in TTD[0] and the LSB is in TTD[7] of the transmit trace ID data TTD[7:0]. DT[1] is the first bit transmitted on the outgoing data stream. Multiframe alignment insertion overwrites the MSB of each trail trace byte with the multiframe alignment signal. The MSB of the first byte in the trail trace identifier is overwritten with a one, the MSB of the other 15 bytes in the trail trace identifier are overwritten with a zero. Multiframe alignment insertion is programmable (on or off). If transmit data inversion is enabled, the outgoing data is inverted after trail trace processing is performed. Transmit data inversion is programmable (on or off). If transmit trail trace identifier idle (Idle) is enabled, the trail trace data is overwritten with all zeros. Transmit Idle is programmable (on or off). 10.12.7 Receive Trace ID Processor The Receive Trace ID Processor receives the incoming serial trace ID data stream and processes the incoming data according to the Receive Trace ID mode, and passes the trace ID data on to Receive Data Storage. The bits in a byte are received MSB first, LSB last. The bits in a byte in an incoming signal are numbered in the order they are received, 1 (MSB) to 8 (LSB). However, when a byte is stored in a register, the MSB is stored in the highest numbered bit (7), and the LSB is stored in the lowest numbered bit (0). This is to differentiate between a byte in a register and the corresponding byte in a signal. 10.12.8 Receive Trail Trace Processing The Receive Trail Trace Processing accepts an incoming data line and performs trail trace alignment, trail trace extraction, expected trail trace comparison, and bit reordering. If receive data inversion is enabled, the incoming data is inverted before trail trace processing is performed. Receive data inversion is programmable (on or off). Trail trace alignment determines the trail trace identifier boundary by identifying the multiframe alignment signal. The multiframe alignment signal (MAS) is located in the MSB of each byte (see Figure 10-48). The MAS bits are each checked for the multiframe alignment start bit, which is a one. Once a multiframe alignment start bit is found, the remaining 15 bits of the MAS are verified as being zero. The MAS check is performed one byte at a time. Multiframe alignment is programmable (on or off). When multiframe alignment is disabled, the incoming bytes are sequentially stored starting with a random byte. 186 DS3181/DS3182/DS3183/DS3184 Figure 10-48. Trail Trace Byte (DT = Trail Trace Data) Bit 1 MSB Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 Bit 8 LSB MAS or DT[1] DT[2] DT[3] DT[4] DT[5] DT[6] DT[7] DT[8] Trail trace extraction extracts the trail trace identifier from the incoming trail trace data stream, generates a trail trace identifier change indication, detects a trail trace identifier idle (Idle) condition, and detects a trail trace identifier unstable (TIU) condition. The trail trace identifier bytes are stored sequentially with the first byte (MAS equals 1 if trail trace alignment is enabled) being stored in the first byte of memory. If the exact same non-zero trail trace identifier is received five consecutive times and it is different from the receive trail trace identifier, a receive trail trace identifier update is performed, and the receive trail trace identifier change indication is set. An Idle condition is declared when an all zeros trail trace identifier is received five consecutive times. An Idle condition is terminated when a non-zero trail trace identifier is received five consecutive times or a TIU condition is declared. A TIU condition is declared if eight consecutive trail trace identifiers are received that do not match either the receive trail trace identifier or the previously stored current trail trace identifier. The TIU condition is terminated when a non-zero trail trace identifier is received five consecutive times or an Idle condition is declared. Expected trail trace comparison compares the received and expected trail trace identifiers. The comparison is a 7bit comparison of the seven least significant bits (DT[2:8] (see Figure 10-48) of each trail trace identifier byte (The multiframe alignment signal is ignored). If the received and expected trail trace identifiers do not match, a trail trace identifier mismatch (TIM) condition is declared. If they do match the TIM condition is terminated. The 16-byte expected trail trace identifier is programmable. Expected trail trace comparison is programmable (on or off). If multiframe alignment is disabled, expected trail trace comparison is disabled. Immediately after a reset, the receive trail trace identifier is invalid. All comparisons between the receive trail trace identifier and expected trail trace identifier will match (a TIM condition cannot occur) until after the first receive trail trace identifier update occurs. Bit reordering changes the bit order of each byte. If bit reordering is disabled, the incoming 8-bit data stream DT[1:8] with DT[1] being the MSB and DT[8] being the LSB is output to the Receive Data Storage with the MSB in RTD[7] and the LSB in RTD[0] of the receive trace ID data RTD[7:0]. If bit reordering is enabled, the incoming 8-bit data stream DT[1:8] is output to the Receive Data Storage with the MSB in RTD[0] and the LSB in RTD[7] of the receive trace ID data RTD[7:0]. DT[1] is the first bit received from the incoming data stream. Once all of the trail trace processing has been completed, The 8-bit parallel data stream is passed on to the Receive Data Storage. 10.12.9 Receive Data Storage The Receive Data Storage block contains memory for 48 bytes of data, maintains data status information, and has controller circuitry for reading and writing the memory. The Receive Data Storage controller functions include filling the memory and maintaining the memory read and write pointers. The Receive Data Storage accepts data and data status from the Receive Trace ID Processor, stores the data in memory, and maintains data status information. The data is read from the Receive Data Storage via the microprocessor interface. The Receive Data Storage contains the current trail trace identifier, the receive trail trace identifier, and the expected trail trace identifier. 187 DS3181/DS3182/DS3183/DS3184 10.13 FEAC Controller 10.13.1 General Description The FEAC Controller demaps FEAC codewords from a DS3/E3 data stream in the receive direction and maps FEAC codewords into a DS3/E3 data stream in the transmit direction. The transmit direction demaps FEAC codewords from a DS3/E3 data stream. The receive direction performs FEAC processing, and stores the codewords in the FIFO using line timing. It removes the codewords from the FIFO and outputs them to the microprocessor via the register interface. The transmit direction inputs codewords from the microprocessor via the register interface and stores the codewords. It removes the codewords and performs FEAC processing. See Figure 10-49 for the location of the FEAC Controller in the block diagram Figure 10-49. FEAC Controller Block Diagram TAIS TUA1 DS3/E3 Receive LIU B3ZS/ HDB3 Decoder Clock Rate Adapter System Interface TX BERT RX BERT Rx Packet Processor DS3 / E3 Receive Framer IEEE P1149.1 JTAG Test Access Port Tx FIFO Tx Packet Processor HDLC PLB Trail FEAC Trace Buffer TX FRAC/ PLCP SLB DLB LLB ALB DS3/E3 Transmit LIU Tx Cell Processor DS3 / E3 Transmit Formatter B3ZS/ HDB3 Encoder RX FRAC/ PLCP UA1 GEN Rx Cell Processor Rx FIFO Microprocessor Interface 10.13.2 Features * * * * Programmable dual codeword output - The transmit side can be programmed to output a single codeword ten times, one codeword ten times followed by a second codeword ten times, or a single codeword continuously. Four codeword receive FIFO Fully independent transmit and receive paths Fully independent Line side and register side timing - The FIFO can be read from or written to at the register interface side while all line side clocks and signals are inactive, and read from or written to at the line side while all register interface side clocks and signals are inactive. 10.13.3 Functional Description The bits in a code are received MSB first, LSB last. When they are output serially, they are output MSB first, LSB last. The bits in a code in an incoming signal are numbered in the order they are received, 1 (MSB) to 6 (LSB). However, when a code is stored in a register, the MSB is stored in the lowest numbered bit (0), and the LSB is stored in the highest numbered bit (5). This is to differentiate between a code in a register and the corresponding code in a signal. 10.13.3.1 Transmit Data Storage The Transmit Data Storage block contains the registers for two FEAC codes (C[1:6]) and controller circuitry for reading and writing the memory. The Transmit Data Storage receives data from the microprocessor interface, and stores the data in memory. The Transmit FEAC Processor reads the data from the Transmit Data Storage. 188 DS3181/DS3182/DS3183/DS3184 10.13.3.2 Transmit FEAC Processor The Transmit FEAC Processor accepts data from the Transmit Data Storage performs FEAC processing. The FEAC codes are read from Transmit Data Storage with the MSB (C[1]) in TFCA[0] or TFCB[0], and the LSB (C[6]) in TFCA[5] or TFCB[5]. FEAC processing has four modes of operation (Idle, single code, dual code, and continuous code). In Idle mode, all ones are output on the outgoing FEAC data stream. In single code mode, the code from TFCA[5:0] is inserted into a codeword (See Figure 10-50), and sent ten consecutive times. Once the ten codewords have been sent, all ones are output. In dual code mode, the code from TFCA[5:0] is inserted into a codeword, and sent ten consecutive times. Then the code from TFCB[5:0] is inserted into a codeword, and sent ten consecutive times. Once both codewords have both been sent ten times, all ones are output. In continuous mode, the code from TFCA[5:0] is inserted into a codeword, and sent until the mode is changed 10.13.3.3 Receive FEAC Processor The Receive FEAC Processor accepts an incoming data line and extracts all overhead and performs FEAC code extraction, and Idle detection. Figure 10-50. FEAC Codeword Format LSB 16 0 MSB 1 Receive/Transmit Order C6 C5 C4 C3 C2 C1 0 1 1 1 1 1 1 1 1 Cx - FEAC Code FEAC code extraction determines the codeword boundary by identifying the codeword sequence and extracts the FEAC code. A FEAC codeword is a repeating 16-bit pattern (See Figure 10-50). The codeword sequence is the pattern (0xxxxxx011111111) that contains each FEAC code (C[6:1]). Each time slot is checked for a codeword sequence. Once a codeword sequence is found, the FEAC code is checked. If the same FEAC code is received in three consecutive codewords without errors, the FEAC code detection indication is set, and the FEAC code is stored in the Receive FIFO with the MSB (C[1]) in RFF[0], and the LSB (C[6]) in RFF[5]. The FEAC code detection indication is cleared if two consecutively received FEAC codewords differ from the current FEAC codeword, or a FEAC Idle condition is detected. Idle detection detects a FEAC Idle condition. A FEAC idle condition is declared if 16 consecutive ones are received. The FEAC Idle condition is terminated when the FEAC code detection indication is set. 10.13.3.4 Receive FEAC FIFO The Receive FIFO block contains memory for four FEAC codes (C[1:6]) and controller circuitry for reading and writing the memory. The Receive FIFO controller functions include filling the memory, tracking the memory fill level, maintaining the memory read and write pointers, and detecting memory overflow and underflow conditions. The Receive FIFO accepts data from the Receive FEAC Processor and stores the data in memory. The data is read from the receive FIFO via the microprocessor interface. The Receive FIFO also outputs FIFO fill status (empty) via the microprocessor interface. All operations are code based (six bits). The Receive FIFO is considered empty when it does not contain any data. The Receive FIFO accepts data from the Receive FEAC Processor until full. If a FEAC code is received while full, the data is discarded and a FIFO overflow condition is declared. If the Receive FIFO is read while the FIFO is empty, the read is ignored. 189 DS3181/DS3182/DS3183/DS3184 10.14 Line Encoder/Decoder 10.14.1 General Description The B3ZS/HDB3 Decoder converts a bipolar signal to a unipolar signal in the receive direction. B3ZS/HDB3 Encoder converts a unipolar signal to a bipolar signal in the transmit direction. In the transmit direction, the Encoder converts the unipolar signal to a bipolar signal, optionally performing zero suppression encoding (HDB3/B3ZS), optionally inserting errors, and outputs the bipolar signal. In the receive direction, the Decoder receives a bipolar signal, monitors it for alarms and errors, optionally performing zero suppression decoding (HDB3/B3ZS), and converts it to a unipolar signal. If the port line interface is configured for a Unipolar mode and the framer is not configured for one of the "-OHM" modes, the BPV detector will count pulses on the RLCVn pin. Figure 10-51 shows the locations of the Line Encoder/Decoder block in the DS318x devices. Figure 10-51. Line Encoder/Decoder Block Diagram TAIS TUA1 DS3/E3 Receive LIU B3ZS/ HDB3 Decoder Clock Rate Adapter System Interface TX BERT RX BERT Rx Packet Processor DS3 / E3 Receive Framer IEEE P1149.1 JTAG Test Access Port Tx FIFO Tx Packet Processor HDLC PLB Trail FEAC Trace Buffer TX FRAC/ PLCP SLB DLB LLB ALB DS3/E3 Transmit LIU Tx Cell Processor DS3 / E3 Transmit Formatter B3ZS/ HDB3 Encoder RX FRAC/ PLCP UA1 GEN Rx Cell Processor Rx FIFO Microprocessor Interface 10.14.2 Features * * * * Performs bipolar to unipolar encoding and decoding - Converts a unipolar signal into an AMI bipolar signal (POS data, and NEG data) and vice versa. Programmable zero suppression - B3ZS or HDB3 zero suppression encoding and decoding can be performed, or the bipolar data stream can be left as an AMI encoded data stream. Programmable receive zero suppression code format - The signature of B3ZS or HDB3 is selectable. Generates and detects alarms and errors - In the receive direction, detects LOS alarm condition BPV errors, and EXZ errors. In the transmit direction, errors can be inserted into the outgoing data stream. 10.14.3 B3ZS/HDB3 Encoder B3ZS/HDB3 Encoder performs unipolar to bipolar conversion and zero suppression encoding. Unipolar to bipolar conversion converts the unipolar data stream into an AMI bipolar data stream (POS and NEG). In an AMI bipolar data stream a zero is represented by a zero on both the POS and NEG signals, and a one is represented by a one on a bipolar signal (POS or NEG), and a zero on the other bipolar signal (NEG or POS). Successive ones are represented by ones that are alternately output on the POS and NEG signals. I.e., if a one is represented by a one on POS and a zero on NEG, the next one will be represented by a one on NEG and a zero on POS. 190 DS3181/DS3182/DS3183/DS3184 Zero suppression encoding converts an AMI bipolar data stream into a B3ZS or HDB3 encoded bipolar data stream. A B3ZS encoded bipolar signal is generated by inserting a B3ZS signature into the bipolar data stream if both the POS and NEG signals are zero for three consecutive clock periods. An HDB3 encoded bipolar signal is generated by inserting an HDB3 signature into the bipolar data stream if both the POS and NEG signals are zero for four consecutive clock periods. Zero suppression encoding can be disabled which will result in AMI-coded data. Error insertion is also performed. Error insertion inserts bipolar violation (BPV) or excessive zero (EXZ) errors onto the bipolar signal. A BPV error will be inserted when three consecutive ones occur. An EXZ error will be inserted when three (or four) consecutive zeros on the bipolar signal occur by inhibiting the insertion of a B3ZS (HDB3) signature. There will be at least one intervening pulse between consecutive BPV or EXZ errors. A single BPV or EXZ error inserted will be detected as a single BPV/EXZ error at the far-end, and will not cause any other type of error to be detected. For example, if a BPV error is inserted, the far-end should not also detect a data error. 10.14.4 Transmit Line Interface The Transmit Line Interface accepts a bipolar data stream from the B3ZS/HDB3 Encoder, performs error insertion, and transmits the bipolar data stream. Error insertion inserts BPV or EXZ errors into the bipolar signal. When a BPV error is to be inserted, the Transmit Line Interface waits for the next occurrence of three consecutive ones. The first bipolar one is generated according to the normal AMI rules. The second bipolar one is generated by transmitting the same values on TPOS and TNEG as the values for the first one. The third bipolar one is generated according to the normal AMI rules. When an EXZ error is to be inserted, the Transmit Line Interface waits for the next occurrence of three (four) consecutive zeros on the bipolar signal, and inhibits the insertion of a B3ZS (HDB3) signature. There must be at least one intervening one between consecutive BPV or EXZ errors. A single BPV or EXZ error inserted must be detected as a single BPV/EXZ error at the far-end, and not cause any other type of error to be detected. For example, if a BPV error is inserted, the far-end should not also detect a data error. If a second error insertion request of a given type (BPV or EXZ) is initiated before a previous request has been completed, the second request will be ignored. The outgoing bipolar data stream consists of positive pulse data (TPOSn) and negative pulse data (TNEGn). TPOSn and TNEGn are updated on the rising edge of TLCLKn. 10.14.5 Receive Line Interface The Receive Line Interface receives a bipolar signal. The incoming bipolar data line consists of positive pulse data (RPOSn), negative pulse data (RNEGn), and clock (RLCLKn) signals. RPOSn and RNEGn are sampled on the rising edge of RLCLKn. The incoming bipolar signal is checked for a Loss Of Signal (LOS) condition, and passed on to B3ZS/HDB3 Decoder. An LOS condition is declared if both RPOSn and RNEGn do not have any transitions for 192 clock cycles. The LOS condition is terminated after 192 clock cycles without any EXZ errors. Note: When zero suppression (B3ZS or HDB3) decoding is disabled, the LOS condition is cleared, and cannot be detected. 10.14.6 B3ZS/HDB3 Decoder The B3ZS/HDB3 Decoder receives a bipolar signal from the LIU (or the RPOS/RNEG pins). The incoming bipolar signal is checked for a Loss of Signal (LOS) condition. A LOS condition is declared if both the positive pulse data and negative pulse data signals do not have any transitions for 192 clock cycles. The LOS condition is terminated after 192 clock cycles without any EXZ errors. B3ZS/HDB3 Decoder performs EXZ detection, zero suppression decoding, BPV detection, and bipolar to unipolar conversion. EXZ detection checks the bipolar data stream for excessive zeros (EXZ) errors. In B3ZS mode, an EXZ error is declared whenever there is an occurrence of 3 or more zeros. In HDB3 mode, an EXZ error is declared whenever there is an occurrence of 4 or more zeros. EXZ errors are accumulated in the EXZ counter (LINE.REXZCR register). Zero suppression decoding converts B3ZS or HDB3 encoded bipolar data into an AMI bipolar signal. In B3ZS mode, the encoded bipolar signal is checked for a B3ZS signature. If a B3ZS signature is found, it is replaced with three zeros. In HDB3 mode, the encoded bipolar signal is checked for an HDB3 signature. If an HDB3 signature is found, it is replaced with four zeros. The format of both an HDB3 signature and a B3ZS signature is programmable. When LINE.RCR.REZSF = 0, the decoder will search for a zero followed by a BPV in B3ZS mode, and in HDB3 mode it will search for two zeros followed by a BPV. If LINE.RCR.REZSF = 1, the same criteria is applied with an additional requirement that the BPV must be the opposite polarity of the previous BPV. See Figure 10-52 and 191 DS3181/DS3182/DS3183/DS3184 Figure 10-53. Zero suppression decoding is also programmable (on or off). Note: Immediately after a reset or a LOS condition, the first B3ZS/HDB3 signature to be detected will not depend upon the polarity of any BPV contained within the signature. Figure 10-52. B3ZS Signatures RLCLK (RX DATA) RPOS RNEG V B3ZS SIGNATURE WHEN LINE.RCR.REZSF = 0 RLCLK (RX DATA) RPOS V RNEG V B3ZS SIGNATURE WHEN LINE.RCR.REZSF = 1 Figure 10-53. HDB3 Signatures RLCLK (RX DATA) RPOS RNEG V HDB3 SIGNATURE WHEN LINE.RCR.REZSF = 0 RLCLK (RX DATA) RPOS RNEG V V HDB3 SIGNATURE WHEN LINE.RCR.REZSF = 1 BPV detection checks the bipolar signal for bipolar violation (BPV) errors and E3 code violation (CV) errors. A BPV error is declared if two 1's are detected on RXP or RXN without an intervening 1 on RXN or RXP, and the 1's are not part of a B3ZS/HDB3 signature, or when both RXP and RXN are a one. An E3 coding violation is declared if consecutive BPVs of the same polarity are detected (ITU O.161 definition). E3 CVs are accumulated in the BPV counter (LINE.RBPVCR register) if E3 CV detection has been enabled (applicable only in HDB3 mode), otherwise, BPVs are accumulated in the BPV counter. If zero code suppression is disabled, the BPV counter will count all bipolar violations. The BPV counter will count pulses on the RLCVn pin when the device is configured for unipolar mode. 192 DS3181/DS3182/DS3183/DS3184 Note: Immediately after a reset (or datapath reset) or a LOS condition, a BPV will not be declared when the first valid one (RPOS high and RNEG low, or RPOS low and RNEG high) is received. Bipolar to unipolar conversion converts the AMI bipolar data into a unipolar signal by ORing together the RXP and RXN signals. 10.15 BERT 10.15.1 General Description The BERT is a software-programmable test-pattern generator and monitor capable of meeting most error performance requirements for digital transmission equipment. It will generate and synchronize to pseudo-random patterns with a generation polynomial of the form xn + xy + 1, where n and y can take on values from 1 to 32 and to repetitive patterns of any length up to 32 bits. The transmit direction generates the programmable test pattern, and inserts the test pattern payload into the data stream. The receive direction extracts the test pattern payload from the receive data stream, and monitors the test pattern payload for the programmable test pattern. Figure 10-54 shows the location of the BERT Block within the DS318x devices. Figure 10-54. BERT Block Diagram TAIS TUA1 DS3/E3 Receive LIU Clock Rate Adapter B3ZS/ HDB3 Decoder System Interface TX BERT RX BERT Rx Packet Processor DS3 / E3 Receive Framer IEEE P1149.1 JTAG Test Access Port Tx FIFO Tx Packet Processor HDLC PLB Trail FEAC Trace Buffer TX FRAC/ PLCP SLB DLB LLB ALB DS3/E3 Transmit LIU Tx Cell Processor DS3 / E3 Transmit Formatter B3ZS/ HDB3 Encoder RX FRAC/ PLCP UA1 GEN Rx Cell Processor Rx FIFO Microprocessor Interface 10.15.2 Features * * * * * Programmable PRBS pattern - The Pseudo Random Bit Sequence (PRBS) polynomial (xn + xy + 1) and seed are programmable (length n = 1 to 32, tap y = 1 to n - 1, and seed = 0 to 2n - 1). Programmable repetitive pattern - The repetitive pattern length and pattern are programmable (the length n = 1 to 32 and pattern = 0 to 2n - 1). 24-bit error count and 32-bit bit count registers Programmable bit error insertion - Errors can be inserted individually, on a pin transition, or at a specific rate. The rate 1/10n is programmable (n = 1 to 7). Pattern synchronization at a 10-3 BER - Pattern synchronization will be achieved even in the presence of a random Bit Error Rate (BER) of 10-3. 10.15.3 Configuration and Monitoring Set PORT.CR1.BENA = 1 to enable the BERT. The BERT must be enabled before the pattern is loaded for the pattern load operation to take affect. The following tables show how to configure the on-board BERT to send and receive common patterns. 193 DS3181/DS3182/DS3183/DS3184 Table 10-38. Pseudorandom Pattern Generation PATTERN TYPE 29-1 O.153 (511 type) 211-1 O.152 and O.153 (2047 type) 215-1 O.151 BERT.PCR REGISTER PTF[4:0] PLF[4:0] PTS QRSS (hex) (hex) 04 08 0 0 BERT. PCR BERT. SPR2 BERT. SPR1 0x0408 0xFFFF 0xFFFF BERT.CR TPIC, RPIC 0 08 0A 0 0 0x080A 0xFFFF 0xFFFF 0 0D 0E 0 0 0x0D0E 0xFFFF 0xFFFF 1 20 10 13 0 0 0x1013 0xFFFF 0xFFFF 0 20 02 13 0 1 0x0253 0xFFFF 0xFFFF 0 23 11 16 0 0 0x1116 0xFFFF 0xFFFF 1 2 -1 O.153 2 -1 O.151 QRSS 2 -1 O.151 Table 10-39. Repetitive Pattern Generation PATTERN TYPE all 1s BERT.PCR REGISTER PTF[4:0] PLF[4:0] PTS QRSS (hex) (hex) NA 00 1 0 BERT. PCR BERT. SPR2 BERT. SPR1 0x0020 0xFFFF 0xFFFF all 0s NA 00 1 0 0x0020 0xFFFF 0xFFFE alternating 1s and 0s NA 01 1 0 0x0021 0xFFFF 0xFFFE double alternating and 0s NA 03 1 0 0x0023 0xFFFF 0xFFFC 3 in 24 NA 17 1 0 0x0037 0xFF20 0x0022 1 in 16 NA 0F 1 0 0x002F 0xFFFF 0x0001 1 in 8 NA 07 1 0 0x0027 0xFFFF 0xFF01 1 in 4 NA 03 1 0 0x0023 0xFFFF 0xFFF1 After configuring these bits, the pattern must be loaded into the BERT. This is accomplished via a zero-to-one transition on BERT.CR.TNPL and BERT.CR.RNPL. Monitoring the BERT requires reading the BERT.SR Register that contains the Bit Error Count (BEC) bit and the Out of Synchronization (OOS) bit. The BEC bit will be one when the bit error counter is one or more. The OOS will be one when the receive pattern generator is not synchronized to the incoming pattern, which will occur when it receives a minimum 6 bit errors within a 64 bit window. The Receive BERT Bit Count Register (BERT.RBCR1) and the Receive BERT Bit Error Count Register (BERT.RBECR1) will be updated upon the reception of a Performance Monitor Update signal (e.g., BERT.CR.LPMU). This signal will update the registers with the values of the counters since the last update and will reset the counters. See Section 10.4.5 for more details of the PMU. 10.15.4 Receive Pattern Detection When the Receive BERT is enabled it can be used as an off-line monitor. The incoming datastream flows to the receive BERT as well as the Cell/Packet Processor. If it is not desired that the datastream flows to the Cell/Packet processor, the user should disable the Receive FIFO by setting the FIFO.RCR.RFRST bit. The Receive BERT receives only the payload data and synchronizes the receive pattern generator to the incoming pattern. The receive pattern generator is a 32-bit shift register that shifts data from the least significant bit (LSB) or bit 1 to the most significant bit (MSB) or bit 32. The input to bit 1 is the feedback. For a PRBS pattern (generating polynomial xn + xy + 1), the feedback is an XOR of bit n and bit y. For a repetitive pattern (length n), the feedback is bit n. The values for n and y are individually programmable (1 to 32). The output of the receive pattern generator is the feedback. If QRSS is enabled, the feedback is an XOR of bits 17 and 20, and the output will be forced to one if the next 14 bits are all zeros. QRSS is programmable (on or off). For PRBS and QRSS patterns, the feedback will be forced to one if bits 1 through 31 are all zeros. Depending on the type of pattern programmed, pattern detection performs either PRBS synchronization or repetitive pattern synchronization. 194 DS3181/DS3182/DS3183/DS3184 10.15.4.1 Receive PRBS Synchronization PRBS synchronization synchronizes the receive pattern generator to the incoming PRBS or QRSS pattern. The receive pattern generator is synchronized by loading 32 data stream bits into the receive pattern generator, and then checking the next 32 data stream bits. Synchronization is achieved if all 32 bits match the incoming pattern. If at least six incoming bits in the current 64-bit window do not match the receive pattern generator, automatic pattern re-synchronization is initiated. Automatic pattern re-synchronization can be disabled. See Figure 10-55 for the PRBS synchronization diagram. Figure 10-55. PRBS Synchronization State Diagram Sync th wi its wit ho its ut 4b err ors f6 6o 32 b ors err 1 bit error Verify Load 32 bits loaded 10.15.4.2 Receive Repetitive Pattern Synchronization Repetitive pattern synchronization synchronizes the receive pattern generator to the incoming repetitive pattern. The receive pattern generator is synchronized by searching each incoming data stream bit position for the repetitive pattern, and then checking the next 32 data stream bits. Synchronization is achieved if all 32 bits match the incoming pattern. If at least six incoming bits in the current 64-bit window do not match the receive PRBS pattern generator, automatic pattern re-synchronization is initiated. Automatic pattern re-synchronization can be disabled. See Figure 10-56 for the repetitive pattern synchronization state diagram. 195 DS3181/DS3182/DS3183/DS3184 Figure 10-56. Repetitive Pattern Synchronization State Diagram Sync th wi its wi tho its ut 4b err ors f6 6o 32 b ors err 1 bit error Verify Match Pattern Matches 10.15.4.3 Receive Pattern Monitoring Receive pattern monitoring monitors the incoming data stream for both an OOS condition and bit errors and counts the incoming bits. An Out Of Synchronization (OOS) condition is declared when the synchronization state machine is not in the "Sync" state. An OOS condition is terminated when the synchronization state machine is in the "Sync" state. Bit errors are determined by comparing the incoming data stream bit to the receive pattern generator output. If they do not match, a bit error is declared, and the bit error and bit counts are incremented. If they match, only the bit count is incremented. The bit count and bit error count are not incremented when an OOS condition exists. 10.15.5 Transmit Pattern Generation Pattern Generation generates the outgoing test pattern, and passes it onto Error Insertion. The transmit pattern generator is a 32-bit shift register that shifts data from the least significant bit (LSB) or bit 1 to the most significant bit (MSB) or bit 32. The input to bit 1 is the feedback. For a PRBS pattern (generating polynomial xn + xy + 1), the feedback is an XOR of bit n and bit y. For a repetitive pattern (length n), the feedback is bit n. The values for n and y are individually programmable (1 to 32). The output of the receive pattern generator is the feedback. If QRSS is enabled, the feedback is an XOR of bits 17 and 20, and the output will be forced to one if the next 14 bits are all zeros. QRSS is programmable (on or off). For PRBS and QRSS patterns, the feedback will be forced to one if bits 1 through 31 are all zeros. When a new pattern is loaded, the pattern generator is loaded with a seed/pattern value before pattern generation starts. The seed/pattern value is programmable (0 - 2n - 1). 10.15.5.1 Transmit Error Insertion Error insertion inserts errors into the outgoing pattern data stream. Errors are inserted one at a time or at a rate of one out of every 10n bits. The value of n is programmable (1 to 7 or off). Single bit error insertion can be initiated from the microprocessor interface, or by the manual error insertion input (TMEI). The method of single error insertion is programmable (register or input). If pattern inversion is enabled, the data stream is inverted before the overhead/stuff bits are inserted. Pattern inversion is programmable (on or off). 196 DS3181/DS3182/DS3183/DS3184 10.16 Line Interface Unit (LIU) 10.16.1 General Description The line interface units (LIUs) perform the functions necessary for interfacing at the physical layer to DS3, E3, or STS-1 lines. Each LIU has independent receive and transmit paths and a built-in jitter attenuator. See Figure 10-57 for the location within the DS318x device of the LIU. Figure 10-57. LIU Functional Diagram TAIS TUA1 DS3/E3 Receive LIU Clock Rate Adapter B3ZS/ HDB3 Decoder System Interface TX BERT RX BERT Rx Packet Processor DS3 / E3 Receive Framer IEEE P1149.1 JTAG Test Access Port Tx FIFO Tx Packet Processor HDLC PLB Trail FEAC Trace Buffer TX FRAC/ PLCP SLB DLB LLB ALB DS3/E3 Transmit LIU Tx Cell Processor DS3 / E3 Transmit Formatter B3ZS/ HDB3 Encoder RX FRAC/ PLCP Rx Cell Processor UA1 GEN Rx FIFO Microprocessor Interface 10.16.2 Features * * * * * * * Each Port Independently Configurable Perform Receive Clock/Data Recovery and Transmit Waveshaping Jitter Attenuators can be Placed in Either the Receive or Transmit Paths Interface to 75 Coaxial Cable at Lengths Up to 380 meters (DS3), 440 meters (E3), or 360 meters (STS-1) Use 1:2 Transformers on TX and RX Require Minimal External Components Local and Remote Loopbacks 10.16.2.1 Transmitter * * * * * * * * Gapped clock capable up to 52MHz Wide 50 20% transmit clock duty cycle Clock inversion for glue-less interfacing Unframed all-ones generator (E3 AIS) Line build-out (LBO) control Tri-state line driver outputs support protection switching applications Per-channel power-down control Output driver monitor 10.16.2.2 Receiver * * * * * * AGC/equalizer block handles from 0 to 15dB of cable loss Loss-of-lock (LOL) PLL status indication Interfaces directly to a DSX monitor signal (~20dB flat loss) using built-in preamp Digital and analog loss-of-signal (LOS) detectors (ANSI T1.231 and ITU G.775) Clock inversion for glue-less interfacing Per-channel power-down control 197 DS3181/DS3182/DS3183/DS3184 10.16.3 Detailed Description The receiver performs clock and data recovery from an alternate mark inversion (AMI) coded signal or a B3ZS- or HDB3-coded AMI signal and monitors for loss of the incoming signal. The transmitter drives standard pulse-shape waveforms onto 75 coaxial cable. See Figure 10-58 for a detailed functional block diagram of the DS3/E3/STS-1 LIU. The jitter attenuator can be mapped into the receiver data path, mapped into the transmitter data path, or be disabled. The DS3/E3/STS1 LIU conforms to the telecommunications standards listed in Table 4-1. Figure 1-1 shows the external components required for proper operation. Figure 10-58. DS3/E3/STS-1 LIU Block Diagram CLKA CLKB CLKC VSS Clock Rate Adapter Automatic Gain Control + Adaptive Equalizer RXPn RXNn Preamp FROM DS3/E3/ STS-1 LINE Power Supply Clock & Data Recovery ALOS squelch Analog Local Loopback TXPn TXNn Line Driver TO DS3/E3/STS-1 LINE Waveshaping Driver Monitor Jitter Attenuator (can be placed in either the receive path or the transmit path) VDD TO B3ZS/HDB3 DECODER FROM B3ZS/HDB3 ENCODER 10.16.4 Transmitter 10.16.4.1 Transmit Clock The clock used in the LIU Transmitter is typically based on either the CLAD clock or TCLKI, selected by the CLADC bit in PORT.CR3. 10.16.4.2 Waveshaping, Line Build-Out, Line Driver The waveshaping block converts the transmit clock, positive data, and negative data signals into a single AMI signal with the waveshape required for interfacing to DS3/E3/STS1 lines. Table 18-8 through Table 18-12 and Figure 18-9 (AC Timing Section) show the waveform template specifications and test parameters. Because DS3 and STS-1 signals must meet the waveform templates at the cross-connect through any cable length from 0 to 450ft, the waveshaping circuitry includes a selectable LBO feature. For cable lengths of 225ft or greater, the TLBO configuration bit (PORT.CR2.TLBO) should be low. When TLBO is low, output pulses are driven onto the coaxial cable without any pre-attenuation. For cable lengths less than 225ft, TLBO should be high to enable the LBO circuitry. When TLBO is high, pulses are pre-attenuated by the LBO circuitry before being driven onto the coaxial cable. The LBO circuitry provides attenuation that mimics the attenuation of 225ft of coaxial cable. The transmitter line driver can be disabled and the TXPn and TXNn outputs tri-stated by asserting the LTS configuration bit (PORT.CR2.LTS). Powering down the transmitter through the TPD configuration bit (CPU bus mode) also tri-states the TXPn and TXNn outputs. 198 DS3181/DS3182/DS3183/DS3184 10.16.4.3 Interfacing to the Line The transmitter interfaces to the outgoing DS3/E3/STS-1 coaxial cable (75) through a 2:1 step-down transformer connected to the TXPn and TXNn pins. Figure 1-1 shows the arrangement of the transformer and other recommended interface components. Table 10-40 specifies the required characteristics of the transformer. 10.16.4.4 Transmit Driver Monitor If the transmit driver monitor detects a faulty transmitter, it sets the PORT.SR.TDM status bit. When the transmitter is tri-stated, the transmit driver monitor is also disabled. The transmitter is declared to be faulty when the transmitter outputs see a load of less than ~25. 10.16.4.5 Transmitter Power-Down To minimize power consumption when the transmitter is not being used, assert the PORT.CR1.PD configuration bit. When the transmitter is powered down, the TXPn and TXNn pins are put in a high-impedance state and the transmit amplifiers are powered down. 10.16.4.6 Transmitter Jitter Generation (Intrinsic) The transmitter meets the jitter generation requirements of all applicable standards, with or without the jitter attenuator enabled. 10.16.4.7 Transmitter Jitter Transfer Without the jitter attenuator enabled in the transmit side, the transmitter passes jitter through unchanged. With the jitter attenuator enabled in the transmit side, the transmitter meets the jitter transfer requirements of all applicable telecommunication standards. See Table 4-1. 10.16.5 Receiver 10.16.5.1 Interfacing to the Line The receiver can be transformer-coupled or capacitor-coupled to the line. Typically, the receiver interfaces to the incoming coaxial cable (75) through a 1:2 step-up transformer. Figure 1-1 shows the arrangement of the transformer and other recommended interface components. Table 10-40 specifies the required characteristics of the transformer. Figure 10-58 shows a general overview of the LIU block. The receiver expects the incoming signal to be in B3ZS- or HDB3-coded AMI format. Table 10-40. Transformer Characteristics PARAMETER Turns Ratio Bandwidth 75 VALUE 1:2ct 2% 0.250MHz to 500MHz (typ) Primary Inductance 19H (min) Leakage Inductance 0.12H (max) Interwinding Capacitance Isolation Voltage 10pF (max) 1500VRMS (min) 199 DS3181/DS3182/DS3183/DS3184 Table 10-41. Recommended Transformers PART TEMP RANGE Pulse Engineering PE-65968 0C to +70C Pulse Engineering PE-65969 0C to +70C MANUFACTURER Halo Electronics Halo Electronics TG070206NS TD070206NE 0C to +70C 0C to +70C PIN-PACKAGE/ SCHEMATIC 6 SMT LS-1/C 6 Thru-Hole LC-1/C 6 SMT SMD/B 6 DIP DIP/B OCL PRIMARY (H) (min) LL (H) (max) BANDWIDTH 75 (MHz) 19 0.06 0.250 to 500 19 0.06 0.250 to 500 19 0.06 0.250 to 500 19 0.06 0.250 to 500 Note: Table subject to change. Industrial temperature range and multiport transformers are also available. Contact the manufacturers for details at www.pulseeng.com and www.haloelectronics.com. 10.16.5.2 Optional Preamp The receiver can be used in monitoring applications, which typically have series resistors with a resistive loss of approximately 20dB. When the PORT.CR2.RMON bit is high, the receiver compensates for this resistive loss by applying flat gain to the incoming signal before sending the signal to the AGC/ equalizer block. 10.16.5.3 Automatic Gain Control (AGC) and Adaptive Equalizer The AGC circuitry applies flat (frequency independent) gain to the incoming signal to compensate for flat losses in the transmission channel and variations in transmission power. Since the incoming signal also experiences frequency-dependent losses as it passes through the coaxial cable, the adaptive equalizer circuitry applies frequency-dependent gain to offset line losses and restore the signal. The AGC/equalizer circuitry automatically adapts to coaxial cable losses from 0 to 15dB, which translates into 0 to 380 meters (DS3), 0 to 440 meters (E3), or 0 to 360 meters (STS-1) of coaxial cable (AT&T 734A or equivalent). The AGC and the equalizer work simultaneously but independently to supply a signal of nominal amplitude and pulse shape to the clock and data recovery block. The AGC/equalizer block automatically handles direct (0 meters) monitoring of the transmitter output signal. 10.16.5.4 Clock and Data Recovery (CDR) The CDR block takes the amplified, equalized signal from the AGC/equalizer block and produces a separate clock, positive data, and negative data signals. The CDR requires a master clock. This clock is derived from CLKA, CLKB, or CLKC depending on the CLAD configuration (DS3, E3, STS-1). If, however, there is no clock source on CLKA, CLKB, or CLKC the CDR block will automatically switch to TCLKIn to use as its master clock. The receive clock is locked using a clock recovery PLL. The status of the PLL lock is indicated in the RLOL (PORT.SR) status bit. The receive loss-of-lock status bit (RLOL) is set when the difference between the recovered clock frequency and the master clock frequency is greater than 7900ppm and cleared when the difference is less than 7700ppm. A change of state of the PORT.SR.RLOL status bit can cause an interrupt on the INT pin if enabled to do so by the PORT.SRIE.RLOLIE interrupt-enable bit. Note that if the master clock is not present, or the master clock is high and TCLK is not present, RLOL is not set. 10.16.5.5 Loss-of-Signal (LOS) Detector The receiver contains analog and digital LOS detectors. The analog LOS detector resides in the AGC/equalizer block. If the incoming signal level is less than a signal level approximately 24dB below nominal, analog LOS (ALOS) is declared. The ALOS signal cannot be directly examined, but when ALOS occurs the AGC/equalizer mutes the recovered data, forcing all zeros out of the data recovery circuitry and causing digital LOS (DLOS). DLOS is determined by the Line Decoder block (see 10.14.4) and indicated by the LOS status bit (LINE.RSR.LOS). ALOS clears when the incoming signal level is greater than or equal to a signal level approximately 18dB below nominal. 200 DS3181/DS3182/DS3183/DS3184 For E3 LOS Assertion: The ALOS detector in the AGC/equalizer block detects that the incoming signal is less than or equal to a signal level approximately 24dB below nominal, and mutes the data coming out of the clock and data recovery block. (24dB below nominal in the "tolerance range" of G.775, where LOS may or may not be declared.) For E3 LOS Clear: The ALOS detector in the AGC/equalizer block detects that the incoming signal is greater than or equal to a signal level approximately 18dB below nominal, and enables data to come out of the CDR block. (18dB is in the "tolerance range" of G.775, where LOS may or may not be declared.) 10.16.5.6 Receiver Power-Down To minimize power consumption when the receiver is not being used, write a one to the PORT.CR1.PD bit. When the receiver is powered down, the RCLKO pin is tri-stated. In addition, the RXP and RXN pins become high impedance. 10.16.5.7 Receiver Jitter Tolerance The receiver exceeds the input jitter tolerance requirements of all applicable telecommunication standards in Table 4-1. See Figure 10-59. Figure 10-59. Receiver Jitter Tolerance JITTER TOLERANCE (UIP-P) 15 10 STS-1 GR253 DS3 GR-499 Cat II 10 DS3 GR-499 Cat I 5 DS318x JITTER TOLERANCE 1.5 E3 G.823 1.0 0.3 0.15 0.1 0.1 30 10 300 100 669 2.3k 1k FREQUENCY (Hz) 201 22.3k 10k 60k 300k 100k 800k 1M DS3181/DS3182/DS3183/DS3184 11 OVERALL REGISTER MAP The register addresses of the global, test and all four ports are concatenated to cover the address range of 000 to 7FF. The address map requires 11 bits of address, ADR[10:0]. The upper address bit A[10] is decoded for the DS3184 and DS3183 devices. The upper address bit A[10] it is not used by the DS3182 and DS3181 devices and must be tied low at the pin. The register banks that are not marked with an "X" are not writeable and read back all zeroes. Bits that are underlined are read-only; all other bits are read-write. After Global Reset, all Registers will be reset to their default values. When writing to registers with unused bits marked with "--", always write a zero to these unused bits and ignore the value read back from these bits. Configuration registers can be written to and read from during a data path reset (DRST low, and RST high). However, all changes to these registers will be ignored during the data path reset. As a result, all initiating action requiring a "0 to 1" transition must be re-initiated after the data path reset is released. All counters saturate at their maximum count. A counter register is updated by asserting (low to high transition) the performance monitoring update signal (RPMU). During the counter register update process, the performance monitoring status signal (RPMS) will be deasserted. The counter register update process consists of loading the counter register with the current count, resetting the counter, forcing the zero count status indication low for one clock period, and then asserting RPMS. No events shall be missed during an update procedure. A latched bit is set when the associated event occurs, and remains set until it is cleared. Once cleared, a latched bit will not be set again until the associated event reoccurs (goes away and comes back). A latched on change bit is a latched bit that is set when the event occurs, and when it goes away. A latched status bit can be cleared using clear on read or clear on write techniques, selectable by the GL.CR1.LSBCRE bit. When clear on read is selected, the latched bits in a latched status register will be cleared after the register is read from. If the device is configured for 16-bit mode, all 16 latched status bits will be cleared. If the device is configured for 8-bit mode, only the 8 bits being accessed will be cleared. When clear on write is selected, the latched bits in a latched status register will be cleared when a logic 1 is written to that bit position. For example, writing a FFFFh to a 16-bit latched status register will clear any latched status bit, whereas writing a 0001h will only clear latched bit 0 of the latched status register. Reserved bits and registers are implemented in a different mode. Reserved configuration bits and registers can be written and read, however they will not effect the operation of the current mode. Reserved status bits will be zero. Reserved latched status bits cannot be set, however, they may remain set or get set during a mode change. Reserved interrupt enable bits can be written and read, and can cause an interrupt if the associated latched status bit is set. Reserved counter registers and the associated counter will retain the values held before a mode change, however, the associated counter cannot be incremented. A performance monitor update will operate normally. If the data path reset is set during or after a mode change, the latched status bits and counter registers (with the associated counters) will be automatically cleared. If the data path reset is not used, then the latched status bits must be cleared via the register interface in the normal manner. And, the counter registers must be cleared by performing two performance monitor updates. The first to clear the associated counter, and load the current count into the counter register, and the second to clear the counter register. 202 DS3181/DS3182/DS3183/DS3184 Table 11-1. Global and Test Register Address Map ADDRESS DESCRIPTION 000-01F Global Registers, Section 12.1 020-02F Unused 030-037 UTOPIA/POS-PHY Transmit System Bus, Section 12.3 038-03F UTOPIA/POS-PHY Receive System Bus, Section 12.3.2 040-1FF Port 1 Register Map 200-23F Test Registers 240-3FF Port 2 Register Map 400-43F Test Registers 440-5FF Port 3 Register Map 600-63F Unused 640-6FF Port 4 Register Map Each port has a relative address range of 040h to 1FFh. The lower 000h to 03Fh address range is used for global, test and reserved registers. The following table is a map of the registers for each port. The address offset is from the start of each port range of 000h, 200h, 400h and 600h. In a DS3183, writes to registers in port 4 will be ignored and reads from port 4 registers will read back zero values. Similarly, in a DS3181, writes to registers in port 2 will be ignored and reads from port 2 will read back zero values. Note: The RDY signal will not go active if the user attempts to read or write unused ports or unused registers not assigned to any design blocks. The RDY signal will go active if the user writes or reads reserved registers or unused registers within design blocks. Table 11-2. Per-Port Register Address Map Port 1 Port 2 Port 3 Port 4 040-1FF 240-3FF 440-5FF 640-7FF ADDRESS OFFSET ADDRESS OFFSET DESCRIPTION DESCRIPTION 040-05F Port Common Registers 100- 117 Reserved 060-07F BERT 118-11F DS3/E3 Framer Transmit 080-08B Reserved 120-13F DS3/E3 Framer Receive 08C-08F B3ZS/HDB3 Transmit Line Encoder 140-147 DS3/E3 Fractional Transmit 090-09F B3ZS/HDB3 Receive Line Decoder 148-14F DS3/E3 Fractional Receive 0A0-0AF HDLC Transmit 150-15F DS3/E3 PLCP Transmit 0B0-0BF HDLC Receive 160-17F DS3/E3 PLCP Receive 0C0-0CF FEAC Transmit 180-18F UTOPIA/POS-PHY Transmit FIFO 0D0-0DF FEAC Receive 190-19F UTOPIA/POS-PHY Receive FIFO 0E0-0E7 Reserved 1A0-1BF Transmit Cell/Packet Processor 0E8-0EF Trail Trace Transmit 1C0-1FF Receive Cell/Packet Processor 0F0-0FF Trail Trace Receive 203 DS3181/DS3182/DS3183/DS3184 12 REGISTER MAPS AND DESCRIPTIONS 12.1 Registers Bit Maps Note: In 8-bit mode, register bits[15:8] correspond to the upper byte, and register bits[7:0] correspond to the lower byte. For example, address 001h is the upper byte (bits [15:8]) and address 000h is the lower byte (bits [7:0]) for register GL.IDR in 8-bit mode. All registers listed, including those designated Unused and Reserved, will cause the RDY signal to go low when written to or read from. The "--" designation indicates that the bit is not assigned. 12.1.1 Global Register Bit Map Table 12-1. Global Register Bit Map Address 16-bit 8-bit 000 000 001 002 002 003 004 004 005 006- 006008 009 00A 00A 00B 00C 00C 00D 010 010 011 012 012 013 014 014 015 016 016 017 018 018 019 01A 01A 01B 01C 01C 01D 01E 01E 01F Register Type GL.IDR R GL.CR1 RW GL.CR2 RW UNUSED GL.GIOCR RW UNUSED GL.ISR R GL.ISRIE RW GL.SR R GL.SRL RL GL.SRIE R UNUSED GL.GIORR UNUSED R Bit 7 Bit 15 Bit 6 Bit 14 Bit 5 Bit 13 Bit 4 Bit 12 Bit 3 Bit 11 Bit 2 Bit 10 Bit 1 Bit 9 Bit 0 Bit 8 ID7 ID15 ID6 ID14 ID5 ID13 ID4 ID12 ID3 ID11 ID2 ID10 ID1 ID9 ID0 ID8 TMEI GWRM -- MEIMS INTM -- GPM1 DIREN -- GPM0 -- -- PMU SIW1 CLAD3 LSBCRE SIW0 CLAD2 RSTDP SIM1 CLAD1 RST SIM0 CLAD0 -- -- -- G8KRS2 G8KRS1 G8KRS0 G8K0S G8KIS -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- GPIO4S1 GPIO4S0 GPIO3S1 GPIO3S0 GPIO2S1 GPIO2S0 GPIO1S1 GPIO1S0 GPIO8S1 GPIO8S0 GPIO7S1 GPIO7S0 GPIO6S1 GPIO6S0 GPIO5S1 GPIO5S0 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- PISR4 PISR3 PISR2 PISR1 -- -- TSSR GSR -- -- -- -- -- -- -- -- PISRIE4 PISRIE3 PISRIE2 PISRIE1 -- -- TSSRIE GSRIE -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 8KREFL -- -- -- -- -- -- -- CLADL -- -- -- -- -- -- -- ONESL -- ONESIE -- -- -- CLOL -- CLOLL -- CLOLIE -- -- -- GPMS -- GPMSL -- GPMSIE -- -- -- GPIO8 GPIO7 GPIO6 GPIO5 GPIO4 GPIO3 GPIO2 GPIO1 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 204 DS3181/DS3182/DS3183/DS3184 Table 12-2. System Interface Bit Map Address 16-bit 8-bit 030 030 031 032 032 033 034 034 035 036 036 037 038 038 039 03A 03A 03B 03C 03C 03D 03E 03E 03F Register Type SI.TCR RW SI.TSRL RL SI.TSRIE RW UNUSED SI.RCR1 RW SI.RCR2 RW SI.RSRL RL UNUSED R Bit 7 Bit 15 Bit 6 Bit 14 Bit 5 Bit 13 Bit 4 Bit 12 Bit 3 Bit 11 Bit 2 Bit 10 Bit 1 Bit 9 Bit 0 Bit 8 -- -- -- -- -- -- -- -- -- -- RLBL7 -- -- -- -- -- -- -- -- -- -- RXAD2 -- RLBL6 -- -- -- TXAD5 -- -- -- -- -- -- RXAD1 -- RLBL5 RMBL5 -- -- TXAD4 -- -- -- -- -- -- RXAD0 -- RLBL4 RMBL4 -- TPARP TXAD3 -- -- -- -- -- -- RPARP -- RLBL3 RMBL3 -- TFLVI TSBRE THECT TXAD2 TXAD1 TXAD0 -- TSCLKAL TPREL -- -- -- -- -- TPREIE -- -- -- -- -- -- -- -- -- RFLVI RSBRE RHECT RMDT2 RMDT1 RMDT0 RLBL2 RLBL1 RLBL0 RMBL2 RMBL1 RMBL0 -- -- RSCLKA -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Bit 7 Bit 15 Bit 6 Bit 14 Bit 5 Bit 13 Bit 4 Bit 12 Bit 3 Bit 11 Bit 2 Bit 10 Bit 1 Bit 9 Bit 0 Bit 8 TMEI NAD MEIM PAIS2 -- PAIS1 PMUM PAIS0 PMU LAIS1 PD LAIS0 RSTDP BENA RST HDSEL FM5 FM4 FM3 FM2 FM1 FM0 LM2 RFTS TCLKS GPIOA2 LBM2 -- -- TLCKI TPOHI RLCKI RPOHI -- -- CPSR -- TDM -- TDML -- TDMIE -- LM1 TFTS TSOFOS GPIOA1 LBM1 -- -- TCKOI TOHSI RCKOI ROHSI -- -- PPSR PSR RLOL -- RLOLL -- RLOLIE -- LM0 TLTS TPFPE GPIOA0 LBM0 -- -- TCKII TOHEI -- -- -- -- FMSR LCSR PMS -- PMSL -- PMSIE -- Table 12-3. Port Register Bit Map Note: J and K are variable dependent upon port. Port 1 Port 2 Port 3 Port 4 J 0 2 4 6 K 1 3 5 7 Address 16-bit 8-bit J40 J40 J41 J42 J42 J43 J44 J44 J45 J46 J46 J47 J48 J48 J49 J4A J4B J4C J4D J4E J4E J4F J50 J50 J51 J52 J52 J53 J54 J54 J55 J56 J56 J57 Register Type PORT.CR1 RW PORT.CR2 RW PORT.CR3 RW PORT.CR4 RW UNUSED UNUSED PORT.ISR R PORT.SR R PORT.SRL RL PORT.SRIE RW RCDIS PMCPE TLEN LTS RMON TLBO RCDV8 P8KRS1 P8KRS0 P8KREF LOOPT CLADC -- -- RCLKS RSOFOS RPFPE GPIOB3 GPIOB2 GPIOB1 GPIOB0 GPIOA3 -- -- -- -- SLB -- -- -- -- -- -- -- -- -- -- TOHI TOHCKI TSOFII TNEGI TPOSI TPDEI TPDTI TPOHSI TPOHEI -- ROHI ROHCKI -- RNEGI RPOSI -- RPDTI RFOHEI RPOHSI -- -- -- -- -- -- -- -- -- -- -- TTSR FSR HSR BSR SFSR -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- RLCLKA TCLKIA -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 205 DS3181/DS3182/DS3183/DS3184 Address Register 16-bit 8-bit J58- J58UNUSED J5E J5F Type Bit 7 Bit 15 Bit 6 Bit 14 Bit 5 Bit 13 Bit 4 Bit 12 Bit 3 Bit 11 Bit 2 Bit 10 Bit 1 Bit 9 Bit 0 Bit 8 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Bit 7 Bit 15 PMUM Bit 6 Bit 14 LPMU Bit 5 Bit 13 RNPL Bit 4 Bit 12 RPIC Bit 3 Bit 11 MPR Bit 2 Bit 10 APRD Bit 1 Bit 9 TNPL Bit 0 Bit 8 TPIC -- -- -- BSP7 BSP15 BSP23 BSP31 -- -- -- -- -- -- -- -- -- -- -- -- BEC7 BEC15 BEC23 -- BC7 BC15 BC23 BC31 -- -- -- QRSS -- BSP6 BSP14 BSP22 BSP30 -- -- -- -- -- -- -- -- -- -- -- -- BEC6 BEC14 BEC22 -- BC6 BC14 BC22 BC30 -- -- -- PTS -- BSP5 BSP13 BSP21 BSP29 TEIR2 -- -- -- -- -- -- -- -- -- -- -- BEC5 BEC13 BEC21 -- BC5 BC13 BC21 BC29 -- -- -- PLF4 PTF4 BSP4 BSP12 BSP20 BSP28 TEIR1 -- -- -- -- -- -- -- -- -- -- -- BEC4 BEC12 BEC20 -- BC4 BC12 BC20 BC28 -- -- -- PLF3 PTF3 BSP3 BSP11 BSP19 BSP27 TEIR0 -- -- -- PMS -- PMSL -- PMSIE -- -- -- BEC3 BEC11 BEC19 -- BC3 BC11 BC19 BC27 -- -- -- PLF2 PTF2 BSP2 BSP10 BSP18 BSP26 BEI -- -- -- -- -- BEL -- BEIE -- -- -- BEC2 BEC10 BEC18 -- BC2 BC10 BC18 BC26 -- -- -- PLF1 PTF1 BSP1 BSP9 BSP17 BSP25 TSEI -- -- -- BEC -- BECL -- BECIE -- -- -- BEC1 BEC9 BEC17 -- BC1 BC9 BC17 BC25 -- -- -- PLF0 PTF0 BSP0 BSP8 BSP16 BSP24 MEIMS -- -- -- OOS -- OOSL -- OOSIE -- -- -- BEC0 BEC8 BEC16 -- BC0 BC8 BC16 BC24 -- -- Bit 7 Bit 15 Bit 6 Bit 14 Bit 5 Bit 13 Bit 4 Bit 12 Bit 3 Bit 11 Bit 2 Bit 10 Bit 1 Bit 9 Bit 0 Bit 8 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- TZSD -- -- -- -- -- -- -- -- -- EXZI -- -- -- E3CVE -- -- -- EXZC -- BPVI -- -- -- REZSF -- -- -- -- -- TSEI -- -- -- RDZSF -- -- -- BPVC -- MEIMS -- -- -- RZSD -- -- -- LOS -- Table 12-4. BERT Register Bit Map Address 16-bit 8-bit J60 J60 J61 J62 J62 J63 J64 J64 J65 J66 J66 J67 J68 J68 J69 J6A J6A J6B J6C J6C J6D J6E J6E J6F J70 J70 J71 J72 J72 J73 J74 J74 J75 J76 J76 J77 J78 J78 J79 J7A J7A J7B J7C- J7C J7E J7F Register Type BERT.CR RW BERT.PCR RW BERT.SPR1 RW BERT.SPR2 RW BERT.TEICR RW UNUSED BERT.SR R BERT.SRL RL BERT.SRIE RW UNUSED BERT.RBECR1 R BERT.RBECR2 R BERT.RBCR1 R BERT.RBCR2 R UNUSED Table 12-5. LINE Register Bit Map Address 16-bit 8-bit J8C J8C J8D J8E J8E J8F J90 J90 J91 J92 J92 J93 J94 J94 J95 Register LINE.TCR Type RW UNUSED LINE.RCR RW UNUSED LINE.RSR R 206 DS3181/DS3182/DS3183/DS3184 Address 16-bit 8-bit J96 J96 J97 J98 J98 J99 J9A J9A J9B J9C J9C J9D J9E J9E J9F Register Type LINE.RSRL RL LINE.RSRIE RW UNUSED LINE.RBPVCR R LINE.REXZCR R Bit 7 Bit 15 Bit 6 Bit 14 Bit 5 Bit 13 Bit 4 Bit 12 Bit 3 Bit 11 Bit 2 Bit 10 Bit 1 Bit 9 Bit 0 Bit 8 -- -- -- -- -- -- ZSCDL -- ZSCDIE EXZL -- EXZIE EXZCL -- EXZCIE BPVL -- BPVIE BPVCL -- BPVCIE LOSL -- LOSIE -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- BPV7 BPV15 EXZ7 EXZ15 BPV6 BPV14 EXZ6 EXZ14 BPV5 BPV13 EXZ5 EXZ13 BPV4 BPV12 EXZ4 EXZ12 BPV3 BPV11 EXZ3 EXZ11 BPV2 BPV10 EXZ2 EXZ10 BPV1 BPV9 EXZ1 EXZ9 BPV0 BPV8 EXZ0 EXZ8 Bit 7 Bit 15 Bit 6 Bit 14 Bit 5 Bit 13 Bit 4 Bit 12 Bit 3 Bit 11 Bit 2 Bit 10 Bit 1 Bit 9 Bit 0 Bit 8 -- -- -- TFD7 -- -- -- -- -- -- -- -- -- -- -- -- -- -- RFOL -- RFOIE -- -- -- -- RFD7 -- -- TPSD -- -- TFD6 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- RFD6 -- -- TFEI -- -- TFD5 -- TFFL5 TFOL -- TFOIE -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- RFD5 -- -- TIFV TDAL4 -- TFD4 -- TFFL4 TFUL -- TFUIE -- -- -- -- RDAL4 -- -- -- -- RPEL -- RPEIE -- -- -- -- RFD4 -- -- TBRE TDAL3 -- TFD3 -- TFFL3 TPEL -- TPEIE -- -- -- RBRE RDAL3 -- -- -- -- RPSL -- RPSIE -- -- -- RPS2 RFD3 -- -- TDIE TDAL2 -- TFD2 TFF TFFL2 -- -- -- -- -- -- RDIE RDAL2 -- -- RFF -- RFFL -- RFFIE -- -- -- RPS1 RFD2 -- -- 12.1.2 HDLC Register Bit Map Table 12-6. HDLC Register Bit Map Address 16-bit 8-bit JA0 JA0 JA1 JA2 JA2 JA3 JA4 JA4 JA5 JA6 JA6 JA7 JA8 JA8 JA9 JAA- JAA JAE JAF JB0 JB0 JB1 JB2 JB2 JB3 JB4 JB4 JB5 JB6 JB6 JB7 JB8 JB8 JB9 JBA JBA JBB JBC JBC JBD JBE JBE JBF Register Type HDLC.TCR RW HDLC.TFDR RW HDLC.TSR R HDLC.TSRL RL HDLC.TSRIE RW UNUSED HDLC.RCR RW UNUSED HDLC.RSR R HDLC.RSRL RL HDLC.RSRIE RW UNUSED HDLC.RFDR UNUSED R 207 TFPD TFRST TDAL1 TDAL0 -- TDPE TFD1 TFD0 TFE THDA TFFL1 TFFL0 TFEL THDAL -- -- TFEIE THDAIE -- -- -- -- -- -- RFPD RFRST RDAL1 RDAL0 -- -- -- -- RFE RHDA -- -- -- RHDAL -- -- -- RHDAIE -- -- -- -- -- -- RPS0 RFDV RFD1 RFD0 -- -- -- -- DS3181/DS3182/DS3183/DS3184 Table 12-7. FEAC Register Bit Map Address 16-bit 8-bit JC0 JC0 JC1 JC2 JC2 JC3 JC4 JC4 JC5 JC6 JC6 JC7 JC8 JC8 JC9 JCA- JCA JCE JCF JD0 JD0 JD1 JD2 JD2 JD3 JD4 JD4 JD5 JD6 JD6 JD7 JD8 JD8 JD9 JDA JDA JDB JDC JDC JDD JDE JDE JDF Register Type FEAC.TCR RW FEAC.TFDR RW FEAC.TSR R FEAC.TSRL RL FEAC.TSRIE RW UNUSED FEAC.RCR RW UNUSED FEAC.RSR R FEAC.RSRL RL FEAC.RSRIE RW UNUSED FEAC.RFDR R UNUSED Bit 7 Bit 15 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- RFFI -- -- -- Bit 6 Bit 14 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Bit 5 Bit 13 -- -- TFCA5 TFCB5 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- RFF5 -- -- -- Bit 4 Bit 12 -- -- TFCA4 TFCB4 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- RFF4 -- -- -- Bit 3 Bit 2 Bit 11 Bit 10 -- TFCL -- -- TFCA3 TFCA2 TFCB3 TFCB2 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- RFFE -- -- -- -- RFFOL -- -- -- RFFOIE -- -- -- -- -- -- RFF3 RFF2 -- -- -- -- -- -- Bit 1 Bit 0 Bit 9 Bit 8 TFS1 TFS0 -- -- TFCA1 TFCA0 TFCB1 TFCB0 -- TFI -- -- -- TFIL -- -- -- TFIIE -- -- -- -- -- -- -- RFR -- -- -- -- -- -- RFCD RFI -- -- RFCDL RFIL -- -- RFCDIE RFIIE -- -- -- -- -- -- RFF1 RFF0 -- -- -- -- -- -- Table 12-8. Trail Trace Register Bit Map Address 16-bit 8-bit JE8 JE8 JE9 JEA JEA JEB JEC JEC JED JEE JEE JEF JF0 JF0 JF1 JF2 JF2 JF3 JF4 JF4 JF5 JF6 JF6 JF7 Register Type TT.TCR RW TT.TTIAR R TT.TIR R UNUSED TT.RCR RW TT.RTIAR R TT.RSR R TT.RSRL RL Bit 7 Bit 15 Bit 6 Bit 14 Bit 5 Bit 13 Bit 4 Bit 12 Bit 3 Bit 11 Bit 2 Bit 10 Bit 1 Bit 9 Bit 0 Bit 8 -- -- -- -- TTD7 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- TTD6 -- -- -- -- -- -- -- -- -- -- -- -- -- Reserved -- TTD5 -- -- -- Reserved -- Reserved Reserved -- -- -- -- Reserved -- Reserved -- TTD4 -- -- -- Reserved -- Reserved Reserved -- -- -- -- TMAD -- TTIA3 -- TTD3 -- -- -- RMAD -- RTIA3 ETIA3 -- -- RTICL -- TIDLE -- TTIA2 -- TTD2 -- -- -- RETCE -- RTIA2 ETIA2 RTIM -- RTIML -- TDIE -- TTIA1 -- TTD1 -- -- -- RDIE -- RTIA1 ETIA1 RTIU -- RTIUL -- TBRE -- TTIA0 -- TTD0 -- -- -- RBRE -- RTIA0 ETIA0 RIDL -- RIDLL -- 208 DS3181/DS3182/DS3183/DS3184 Address 16-bit 8-bit JF8 JF8 JF9 JFA JFA JFB JFC JFC JFD JFE JFE JFF K00- K00K16 K117 Register TT.RSRIE Type RW UNUSED TT.RIR R TT.EIR R RESERVED Bit 7 Bit 15 Bit 6 Bit 14 Bit 5 Bit 13 Bit 4 Bit 12 Bit 3 Bit 11 Bit 2 Bit 10 Bit 1 Bit 9 Bit 0 Bit 8 -- -- -- -- RTD7 -- ETD7 -- -- -- -- -- -- -- RTD6 -- ETD6 -- -- -- -- -- -- -- RTD5 -- ETD5 -- -- -- -- -- -- -- RTD4 -- ETD4 -- -- -- RTICIE -- -- -- RTD3 -- ETD3 -- -- -- RTIMIE -- -- -- RTD2 -- ETD2 -- -- -- RTIUIE -- -- -- RTD1 -- ETD1 -- -- -- RIDLIE -- -- -- RTD0 -- ETD0 -- -- -- Bit 7 Bit 15 Bit 6 Bit 14 Bit 5 Bit 13 Bit 4 Bit 12 Bit 3 Bit 11 Bit 2 Bit 10 Bit 1 Bit 9 Bit 0 Bit 8 -- -- Reserved -- -- -- RAILE -- -- -- OOMF Reserved -- -- OOMFL Reserved -- -- OOMFIE Reserved -- -- -- -- FE7 FE15 PE7 PE15 FBE7 FBE15 CPE7 CPE15 -- -- -- -- CPEIE -- -- -- RAILD COVHD -- -- SEF Reserved -- -- SEFL Reserved -- -- SEFIE Reserved -- -- -- -- FE6 FE14 PE6 PE14 FBE6 FBE14 CPE6 CPE14 -- -- TFEBE -- PEI -- -- -- RAIOD MAOD -- -- -- -- -- -- COFAL Reserved -- -- COFAIE Reserved -- -- -- -- FE5 FE13 PE5 PE13 FBE5 FBE13 CPE5 CPE13 -- -- AFEBED PBGE FEIC1 -- -- -- RAIAD MDAISI -- -- LOF Reserved -- -- LOFL Reserved -- -- LOFIE Reserved -- -- -- -- FE4 FE12 PE4 PE12 FBE4 FBE12 CPE4 CPE12 -- -- TRDI TIDLE FEIC0 CCPEIE -- -- ROMD AAISD -- -- RAI T3FM CPEC -- RAIL T3FML CPECL CPEL RAIIE T3FMIE CPECIE CPEIE -- -- FE3 FE11 PE3 PE11 FBE3 FBE11 CPE3 CPE11 -- -- ARDID CBGD FEI CPEI -- -- LIP1 ECC -- -- AIS AIC FBEC -- AISL AICL FBECL FBEL AISIE AICIE FBECIE FBEIE -- -- FE2 FE10 PE2 PE10 FBE2 FBE10 CPE2 CPE10 -- -- 12.1.3 T3 Register Bit Map Table 12-9. T3 Register Bit Map Address 16-bit 8-bit K18 K18 K19 K1A K1A K1B K1C- K1C K1E K1F K20 K20 K21 K22 K22 K23 K24 K24 K25 K26 K26 K27 K28 K28 K29 K2A K2A K2B K2C K2C K2D K2E K2E K2F K30- K30 K32 K33 K34 K34 K35 K36 K36 K37 K38 K38 K39 K3A K3A K3B K3C- K3C K3E K3F Register Type T3.TCR RW T3.TEIR RW RESERVED T3.RCR RW RESERVED T3.RSR1 R T3.RSR2 R T3.RSRL1 RL T3.RSRL2 RL T3.RSRIE1 RW T3.RSRIE2 RW RESERVED T3.RFECR R T3.RPECR R T3.RFBECR R T3.RCPECR R UNUSED 209 TFGD TAIS -- -- TSEI MEIMS CFBEIE FBEI -- -- -- -- LIP0 FRSYNC FECC1 FECC0 -- -- -- -- OOF LOS IDLE RUA1 PEC FEC -- -- OOFL LOSL IDLEL RUA1L PECL FECL PEL FEL OOFIE LOSIE IDLEIE RUA1IE PECIE FECIE PEIE FEIE -- -- -- -- FE1 FE0 FE9 FE8 PE1 PE0 PE9 PE8 FBE1 FBE0 FBE9 FBE8 CPE1 CPE0 CPE9 CPE8 -- -- -- -- DS3181/DS3182/DS3183/DS3184 12.1.4 E3 G.751 Register Bit Map Table 12-10. E3 G.751 Register Bit Map Address 16-bit 8-bit K18 K18 K19 K1A K1A K1B K1C- K1C K1E K1F K20 K20 K21 K22 K22 K23 K24 K24 K25 K26 K26 K27 K28 K28 K29 K2A K2A K2B K2C K2C K2D K2E K2E K2F K30- K30 K32 K33 K34 K34 K35 K36- K36K3A K3B K3C- K3CK3E K3F Register Type E3G751.TCR RW E3G751.TEIR RW RESERVED E3G751.RCR RW RESERVED E3G751.RSR1 R E3G751.RSR2 R E3G751.RSRL1 RL E3G751.RSRL2 RL E3G751.RSRIE1 RW E3G751.RSRIE2 RW RESERVED E3G751.RFECR RESERVED UNUSED R Bit 7 Bit 15 Bit 6 Bit 14 Bit 5 Bit 13 Bit 4 Bit 12 Bit 3 Bit 11 Bit 2 Bit 10 Bit 1 Bit 9 Bit 0 Bit 8 -- -- Reserved Reserved TABC1 TABC0 TFGD TAIS Reserved -- -- Reserved Reserved Reserved TNBC1 TNBC0 Reserved Reserved Reserved FEIC1 FEIC0 FEI TSEI MEIMS -- -- -- -- Reserved Reserved Reserved Reserved -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- RAILE RAILD RAIOD RAIAD ROMD LIP1 LIP0 FRSYNC Reserved Reserved DLS MDAISI AAISD ECC FECC1 FECC0 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- RAB RNB -- LOF RAI AIS OOF LOS Reserved Reserved -- Reserved Reserved Reserved Reserved RUA1 -- -- -- -- Reserved Reserved Reserved FEC -- -- -- -- -- -- ACL NCL COFAL LOFL RAIL AISL Reserved Reserved Reserved Reserved Reserved Reserved -- -- -- -- Reserved Reserved -- -- -- -- Reserved Reserved ACIE NCIE COFAIE LOFIE RAIIE AISIE Reserved Reserved Reserved Reserved Reserved Reserved -- -- -- -- Reserved Reserved -- -- -- -- Reserved Reserved -- -- -- -- -- -- -- -- -- -- -- -- FE7 FE6 FE5 FE4 FE3 FE2 FE15 FE14 FE13 FE12 FE11 FE10 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 210 -- -- OOFL LOSL Reserved RUA1L Reserved FECL Reserved FEL OOFIE LOSIE Reserved RUA1IE Reserved FECIE Reserved FEIE -- -- -- -- FE1 FE0 FE9 FE8 -- -- -- -- -- -- -- -- DS3181/DS3182/DS3183/DS3184 12.1.5 E3 G.832 Register Bit Map Table 12-11. E3 G.832 Register Bit Map Address 16-bit 8-bit K18 K18 K19 K1A K1A K1B K1C K1C K1D K1E K1E K1F K20 K20 K21 K22 K22 K23 K24 K24 K25 K26 K26 K27 K28 K28 K29 K2A K2A K2B K2C K2C K2D K2E K2E K2F K30 K30 K31 K32 K32 K33 K34 K34 K35 K36 K36 K37 K38 K38 K39 K3A K3A K3B K3C- K3CK3E K3F Register Type E3G832.TCR RW E3G832.TEIR RW E3G832.TMAB RW R E3G832.TNGB RW R E3G832.RCR RW E3G832.RMACR RW E3G832.RSR1 R E3G832.RSR2 R E3G832.RSRL1 RL E3G832.RSRL2 RL E3G832.RSRIE1 RW E3G832.RSRIE2 RW E3G832.RMABR R E3G832.RNGBR R E3G832.RFECR R E3G832.RPECR R E3G832.RFBER R RESERVED UNUSED Bit 7 Bit 15 Bit 6 Bit 14 Bit 5 Bit 13 -- -- TFEBE Reserved -- -- Reserved Reserved Reserved -- -- -- TPT2 TPT1 TPT0 -- -- -- TNR7 TNR6 TNR5 TGC7 TGC6 TGC5 RDILE RDILD RDIOD Reserved PEC DLS -- -- -- -- -- -- Reserved Reserved -- Reserved TIU -- -- -- -- -- -- -- GCL NRL COFAL Reserved TIUL TIL -- -- -- -- -- -- GCIE NRIE COFAIE Reserved -- TIIE -- -- -- -- -- -- -- RPT2 RPT1 -- -- -- RNR7 RNR6 RNR5 RGC7 RGC6 RGC5 FE7 FE6 FE5 FE15 FE14 FE13 PE7 PE6 PE5 PE15 PE14 PE13 FBE7 FBE6 FBE5 FBE15 FBE14 FBE13 -- -- -- -- -- -- -- -- -- -- -- -- 211 Bit 4 Bit 12 AFEBED Reserved FEIC1 -- TTIGD -- TNR4 TGC4 RDIAD MDAISI -- -- LOF RPTU -- -- LOFL RPTUL -- -- LOFIE RPTUIE -- -- RPT0 -- RNR4 RGC4 FE4 FE12 PE4 PE12 FBE4 FBE12 -- -- -- -- Bit 3 Bit 11 Bit 2 Bit 10 Bit 1 Bit 9 Bit 0 Bit 8 TRDI ARDID TFGD TAIS Reserved TGCC TNRC1 TNRC0 FEIC0 FEI TSEI MEIMS Reserved Reserved Reserved Reserved TTI3 TTI2 TTI1 TTI0 -- -- -- -- TNR3 TNR2 TNR1 TNR0 TGC3 TGC2 TGC1 TGC0 ROMD LIP1 LIP0 FRSYNC AAISD ECC FECC1 FECC0 EPT2 EPT1 EPT0 TIED -- -- -- -- RAI AIS OOF LOS RPTM Reserved Reserved RUA1 Reserved FBEC PEC FEC -- -- -- -- RAIL AISL OOFL LOSL RPTML RPTL Reserved RUA1L Reserved FBECL PECL FECL Reserved FBEL PEL FEL RAIIE AISIE OOFIE LOSIE RPTMIE RPTIE Reserved RUA1IE Reserved FBECIE PECIE FECIE Reserved FBEIE PEIE FEIE TI3 TI2 TI1 TI0 -- -- -- -- RNR3 RNR2 RNR1 RNR0 RGC3 RGC2 RGC1 RGC0 FE3 FE2 FE1 FE0 FE11 FE10 FE9 FE8 PE3 PE2 PE1 PE0 PE11 PE10 PE9 PE8 FBE3 FBE2 FBE1 FBE0 FBE11 FBE10 FBE9 FBE8 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- DS3181/DS3182/DS3183/DS3184 12.1.6 Clear-Channel Register Bit Map Table 12-12. Clear-Channel Register Bit Map Address 16-bit 8-bit K18 K18 K19 K1A- K1A K1E K1F K20 K20 K21 K22 K22 K23 K24 K24 K25 K26 K26 K27 K28 K28 K29 K2A K2A K2B K2C K2C K2D K2E- K2EK3A K3B K3C- K3CK3E K3F Register CC.TCR Type RW RESERVED CC.RCR RW RESERVED CC.RSR1 R RESERVED CC.RSRL1 RL RESERVED CC.RSRIE1 RW RESERVED UNUSED Bit 7 Bit 15 Bit 6 Bit 14 Bit 5 Bit 13 Bit 4 Bit 12 Bit 3 Bit 11 Bit 2 Bit 10 Bit 1 Bit 9 Bit 0 Bit 8 -- Reserved -- -- Reserved Reserved -- -- Reserved Reserved -- -- Reserved Reserved -- -- Reserved Reserved -- -- -- -- -- -- -- -- Reserved Reserved -- -- Reserved Reserved -- -- Reserved Reserved -- -- Reserved Reserved -- -- -- -- Reserved -- -- -- Reserved Reserved -- -- -- -- -- -- Reserved Reserved -- -- Reserved Reserved -- -- -- -- Reserved Reserved -- -- Reserved MDAISI -- -- Reserved Reserved -- -- Reserved Reserved -- -- Reserved Reserved -- -- -- -- Reserved Reserved -- -- Reserved AAISD -- -- Reserved Reserved -- -- Reserved Reserved -- -- Reserved Reserved -- -- -- -- Reserved Reserved -- -- Reserved Reserved -- -- Reserved Reserved -- -- Reserved Reserved -- -- Reserved Reserved -- -- -- -- Reserved Reserved -- -- Reserved Reserved -- -- Reserved Reserved -- -- Reserved Reserved -- -- Reserved Reserved -- -- -- -- TAIS Reserved -- -- Reserved Reserved -- -- LOS RUA1 -- -- LOSL RUA1L -- -- LOSIE RUA1IE -- -- -- -- Bit 2 Bit 10 Bit 1 Bit 9 Bit 0 Bit 8 12.1.7 Fractional Register Bit Map Table 12-13. Fractional Register Bit Map Address 16-bit 8-bit K40 K40 K41 K42 K42 K43 K44 K44 K45 K46 K46 K47 K48 K48 K49 K4A K4A K4B K4C K4C K4D K4E K4E K4F Register FRAC.TCR Type RW FRAC.TDGSR RW FRAC.TSASR RW UNUSED FRAC.RCR RW FRAC.RDGSR RW FRAC.RSASR RW UNUSED Bit 7 Bit 15 Bit 6 Bit 14 Bit 5 Bit 13 Bit 4 Bit 12 Bit 3 Bit 11 -- -- TDGS7 -- TSAS7 -- -- -- -- -- RDGS7 -- RSAS7 -- -- -- -- -- TDGS6 -- TSAS6 -- -- -- -- -- RDGS6 -- RSAS6 -- -- -- -- -- TDGS5 -- TSAS5 -- -- -- -- -- RDGS5 -- RSAS5 -- -- -- -- -- TDGS4 TDGS12 TSAS4 TSAS12 -- -- -- -- RDGS4 RDGS12 RSAS4 RSAS12 -- -- -- -- TDGS3 TDGS11 TSAS3 TSAS11 -- -- -- -- RDGS3 RDGS11 RSAS3 RSAS11 -- -- 212 TFOSC1 TFOSC0 -- -- TDGS2 TDGS1 TDGS10 TDGS9 TSAS2 TSAS1 TSAS10 TSAS9 -- -- -- -- -- -- -- -- RDGS2 RDGS1 RDGS10 RDGS9 RSAS2 RSAS1 RSAS10 RSAS9 -- -- -- -- TSASS -- TDGS0 TDGS8 TSAS0 TSAS8 -- -- RSASS -- RDGS0 RDGS8 RSAS0 RSAS8 -- -- DS3181/DS3182/DS3183/DS3184 Table 12-14. PLCP Register Bit Map Address 16-bit 8-bit K50 K50 K51 K52 K52 K53 K54 K54 K55 K56 K56 K57 K58 K58 K59 K5A K5A K5B K5C K5C K5D K5E K5E K5F K60 K60 K61 K62 K62 K63 K64 K64 K65 K66 K66 K67 K68 K68 K69 K6A K6A K6B K6C K6C K6D K6E K6E K6F K70 K70 K71 K72 K72 K73 K74 K74 K75 K76 K76 K77 K78 K78 K79 K7A K7A K7B K7C K7C K7D K7E K7E K7F Register Type PLCP.TCR RW PLCP.TEIR RW PLCP.TFGBR RW PLCP.TM12BR RW PLCP.TZ12BR RW PLCP.TZ34BR RW PLCP.TZ56BR RW UNUSED PLCP.RCR RW UNUSED PLCP.RSR1 R PLCP.RSR2 R PLCP.RSRL1 RL PLCP.RSRL2 RL PLCP.RSRIE1 RW PLCP.RSRIE2 RW PLCP.RFECR R PLCP.RPECR R PLCP.RREICR R PLCP.RFGBR R PLCP.RM12BR R PLCP.RZ12BR R PLCP.RZ34BR R PLCP.RZ56BR R Bit 7 Bit 15 -- -- -- -- TREI3 TF17 TM17 TM27 TZ17 TZ27 TZ37 TZ47 TZ57 TZ67 -- -- Bit 6 Bit 14 -- -- -- -- TREI2 TF16 TM16 TM26 TZ16 TZ26 TZ36 TZ46 TZ56 TZ66 -- -- Bit 5 Bit 13 -- -- FEE REIME TREI1 TF15 TM15 TM25 TZ15 TZ25 TZ35 TZ45 TZ55 TZ65 -- -- Bit 4 Bit 12 TMC1 -- FEIC1 CREIIE TREI0 TF14 TM14 TM24 TZ14 TZ24 TZ34 TZ44 TZ54 TZ64 -- -- -- -- RLIE -- -- -- -- -- -- -- -- -- -- -- RZ3L -- -- -- RZ3IE -- FE7 FE15 PE7 PE15 REI7 REI15 -- RF17 RM17 RM27 RZ17 RZ27 RZ37 RZ47 RZ57 RZ67 -- -- -- -- -- -- -- -- RZ2L -- -- -- RZ2IE -- FE6 FE14 PE6 PE14 REI6 REI14 -- RF16 RM16 RM26 RZ16 RZ26 RZ36 RZ46 RZ56 RZ66 -- -- REIC -- -- -- REICL REIL RZ1L -- REICIE REIIE RZ1IE -- FE5 FE13 PE5 PE13 REI5 REI13 -- RF15 RM15 RM25 RZ15 RZ25 RZ35 RZ45 RZ55 RZ65 213 Bit 3 Bit 2 Bit 11 Bit 10 TMC0 TF1C1 -- -- FEIC0 FEI REIEI PBEE TRAI TLSS2 TF13 TF12 TM13 TM12 TM23 TM22 TZ13 TZ12 TZ23 TZ22 TZ33 TZ32 TZ43 TZ42 TZ53 TZ52 TZ63 TZ62 -- -- -- -- Bit 1 Bit 9 TF1C0 -- TSEI CPEIE TLSS1 TF11 TM11 TM21 TZ11 TZ21 TZ31 TZ41 TZ51 TZ61 -- -- Bit 0 Bit 8 AREID -- MEIMS PEI TLSS0 TF10 TM10 TM20 TZ10 TZ20 TZ30 TZ40 TZ50 TZ60 -- -- PECC -- FEPD -- ECC RHSC1 FRSYNC RHSC0 -- -- PEC -- -- -- PECL PEL RM2L -- PECIE PEIE RM2IE -- FE4 FE12 PE4 PE12 REI4 REI12 -- RF14 RM14 RM24 RZ14 RZ24 RZ34 RZ44 RZ54 RZ64 -- -- FEC -- -- -- FECL FEL RM1L -- FECIE FEIE RM1IE -- FE3 FE11 PE3 PE11 REI3 REI11 -- RF13 RM13 RM23 RZ13 RZ23 RZ33 RZ43 RZ53 RZ63 FECC -- -- -- -- -- RAI -- -- -- -- -- -- -- RAIL COFAL -- -- RF1L LSSL RZ5L RZ6L RAIIE COFAIE -- -- RF1IE LSSIE RZ6IE RZ5IE FE2 FE1 FE10 FE9 PE2 PE1 PE10 PE9 REI2 REI1 REI10 REI9 LSS2 LSS1 RF12 RF11 RM12 RM11 RM22 RM21 RZ12 RZ11 RZ22 RZ21 RZ32 RZ31 RZ42 RZ41 RZ52 RZ51 RZ62 RZ61 -- -- OOF LOF LSSU -- OOFL LOFL LSSUL RZ4L OOFIE LOFIE LSSUIE RZ4IE FE0 FE8 PE0 PE8 REI0 REI8 LSS0 RF10 RM10 RM20 RZ10 RZ20 RZ30 RZ40 RZ50 RZ60 DS3181/DS3182/DS3183/DS3184 Table 12-15. FIFO Register Bit Map Address 16-bit 8-bit K80 K80 K81 K82 K82 K83 K84 K84 K85 K86 K86 K87 K88 K88 K89 K8A K8A K8B K8C- K8C K8F K8F K90 K90 K91 K92 K92 K93 K94 K94 K95 K96 K96 K97 K98 K98 K99 K9A K9A K9B K9C- K9C K9F K9F Register Type FF.TCR RW FF.TLCR RW FF.TPAC RW UNUSED FF.TSRL RL FF.TSRIE RW UNUSED FF.RCR RW FF.RLCR RW FF.RFPAC RW UNUSED FF.RSRL RL FF.RSRIE RW UNUSED Bit 7 Bit 15 Bit 6 Bit 14 Bit 5 Bit 13 Bit 4 Bit 12 Bit 3 Bit 11 Bit 2 Bit 10 Bit 1 Bit 9 Bit 0 Bit 8 -- -- -- -- -- -- -- -- -- -- TFAF5 TFAE5 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- RFAF5 RFAE5 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- TFAF4 TFAE4 TPA4 -- -- -- TFATL -- TFATIE -- -- -- -- -- RFAF4 RFAE4 RPA4 -- -- -- -- -- -- -- -- -- -- -- TFAF3 TFAE3 TPA3 -- -- -- TFSTL -- TFSTIE -- -- -- -- -- RFAF3 RFAE3 RPA3 -- -- -- -- -- -- -- -- -- -- -- TFAF2 TFAE2 TPA2 -- -- -- TFITL -- TFITIE -- -- -- -- -- RFAF2 RFAE2 RPA2 -- -- -- -- -- -- -- -- -- -- -- TFAF1 TFAE1 TPA1 -- -- -- TFUL -- TFUIE -- -- -- -- -- RFAF1 RFAE1 RPA1 -- -- -- -- -- -- -- -- -- TFRST -- TFAF0 TFAE0 TPA0 -- -- -- TFOL -- TFOIE -- -- -- RFRST -- RFAF0 RFAE0 RPA0 -- -- -- RFOL -- RFOIE -- -- -- 214 DS3181/DS3182/DS3183/DS3184 12.1.8 Transmit Cell Processor Bit Map Table 12-16. Transmit Cell Processor Register Bit Map Address 16-bit 8-bit KA0 KA0 KA1 KA2 KA2 KA3 KA4 KA4 KA5 KA6 KA6 KA7 KAA KAA KA9 KAA KAA KAB KAC KAC KAD KAE KAE KAF KB0 KB0 KB1 KB2 KB2 KB3 KB4 KB4 KB5 KB6 KB6 KB7 KB8- KB8KBE KBF KBC- KBCKBE KBF Register CP.TCR Type RW RESERVED CP.TECC RW CP.THMRC RW CP.THPC1 RW CP.THPC2 RW CP.TFPPC RW CP.TSR R CP.TSRL RL CP.TSRIE RW CP.TCCR1 R CP.TCCR2 R RESERVED UNUSED Bit 7 Bit 15 Bit 6 Bit 14 Bit 5 Bit 13 Bit 4 Bit 12 Bit 3 Bit 11 Bit 2 Bit 10 Bit 1 Bit 9 Bit 0 Bit 8 TSD TDHE -- -- TCEN2 TCER2 THEM2 -- THP2 THP10 THP18 THP26 TBRE THPE -- -- TCEN1 TCER1 THEM1 -- THP1 THP9 THP17 THP25 TPTE TCPAD -- -- TCEN0 TCER0 THEM0 -- THP0 THP8 THP16 THP24 -- -- TFCH TFCP -- -- -- -- -- -- TCEN7 MEIMS THEM7 -- THP7 THP15 THP23 THP31 -- -- TCEN6 TCER6 THEM6 -- THP6 THP14 THP22 THP30 -- -- TCEN5 TCER5 THEM5 -- THP5 THP13 THP21 THP29 -- -- TCEN4 TCER4 THEM4 -- THP4 THP12 THP20 THP28 THSE TDSE -- -- TCEN3 TCER3 THEM3 -- THP3 THP11 THP19 THP27 TFPP7 TFPP6 TFPP5 TFPP4 TFPP3 TFPP2 TFPP1 TFPP0 -- -- -- -- -- -- -- TCC7 TCC15 TCC23 -- -- -- -- -- -- -- -- -- -- -- -- TCC6 TCC14 TCC22 -- -- -- -- -- -- -- -- -- -- -- -- TCC5 TCC13 TCC21 -- -- -- -- -- -- -- -- -- -- -- -- TCC4 TCC12 TCC20 -- -- -- -- -- -- -- -- -- -- -- -- TCC3 TCC11 TCC19 -- -- -- -- -- -- -- -- -- -- -- -- TCC2 TCC10 TCC18 -- -- -- -- -- -- -- -- -- -- -- -- TCC1 TCC9 TCC17 -- -- -- -- -- -- TECF -- TECFL -- TECFIE -- TCC0 TCC8 TCC16 -- -- -- -- -- 215 DS3181/DS3182/DS3183/DS3184 12.1.9 Transmit Packet Processor Bit Map Table 12-17. Transmit Packet Processor Register Bit Map Address 16-bit 8-bit KA0 KA0 KA1 KA2 KA2 KA3 KA4 KA4 KA5 KA6- KA6KAC KAD KAE KAE KAF KB0 KB0 KB1 KB2 KB2 KB3 KB4 KB4 KB5 KB6 KB6 KB7 KB8 KB8 KB9 KBA KBA KBB KBC- KBCKBE KBF Register Type PP.TCR RW PP.TIFGC RW PP.TEPC RW RESERVED PP.TSR R PP.TSRL RL PP.TSRIE RW PP.TPCR1 R PP.TPCR2 R PP.TBCR1 R PP.TBCR2 R RESERVED Bit 7 Bit 15 Bit 6 Bit 14 Bit 5 Bit 13 Bit 4 Bit 12 Bit 3 Bit 11 Bit 2 Bit 10 Bit 1 Bit 9 Bit 0 Bit 8 -- -- TIFG7 -- TPEN7 MEIMS -- -- -- -- -- -- -- -- TPC7 TPC15 TPC23 -- TBC7 TBC15 TBC23 TBC31 -- -- -- -- TIFG6 -- TPEN6 TPER6 -- -- -- -- -- -- -- -- TPC6 TPC14 TPC22 -- TBC6 TBC14 TBC22 TBC30 -- -- TFAD -- TIFG5 -- TPEN5 TPER5 -- -- -- -- -- -- -- -- TPC5 TPC13 TPC21 -- TBC5 TBC13 TBC21 TBC29 -- -- TF16 -- TIFG4 -- TPEN4 TPER4 -- -- -- -- -- -- -- -- TPC4 TPC12 TPC20 -- TBC4 TBC12 TBC20 TBC28 -- -- TIFV RES TIFG3 -- TPEN3 TPER3 -- -- -- -- -- -- -- -- TPC3 TPC11 TPC19 -- TBC3 TBC11 TBC19 TBC27 -- -- TSD RES TIFG2 -- TPEN2 TPER2 -- -- -- -- -- -- -- -- TPC2 TPC10 TPC18 -- TBC2 TBC10 TBC18 TBC26 -- -- TBRE RES TIFG1 -- TPEN1 TPER1 -- -- -- -- -- -- -- -- TPC1 TPC9 TPC17 -- TBC1 TBC9 TBC17 TBC25 -- -- TPTE RES TIFG0 -- TPEN0 TPER0 -- -- TEPF -- TEPFL -- TEPFIE -- TPC0 TPC8 TPC16 -- TBC0 TBC8 TBC16 TBC24 -- -- Bit 3 Bit 11 Bit 2 Bit 10 Bit 1 Bit 9 Bit 0 Bit 8 Table 12-18. Receive Cell Processor Register Bit Map Address 16-bit 8-bit KC0 KC0 KC1 KC2 KC2 KC3 KC4 KC4 KC5 KC6 KC6 KC7 KC8 KC8 KC9 KCA KCA KCB KCC KCC KCD KCE KCE KCF KD0 KD0 KD1 Register CP.RCR1 Type RW RESERVED CP.RHPC1 RW CP.RHPC2 RW CP.RHPMC1 RW CP.RHPMC2 RW CP.RLTC RW CP.RSR R CP.RSRL RL Bit 7 Bit 15 Bit 6 Bit 14 Bit 5 Bit 13 Bit 4 Bit 12 RROC1 RROC0 RCPAD RHECD RHDE RDD RBRE RPTE RDDE RDHE RECED RHPM1 RHPM0 RICFD RUCFE RICFE -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- RHP7 RHP6 RHP5 RHP4 RHP3 RHP2 RHP1 RHP0 RHP15 RHP14 RHP13 RHP12 RHP11 RHP10 RHP9 RHP8 RHP23 RHP22 RHP21 RHP20 RHP19 RHP18 RHP17 RHP16 RHP31 RHP30 RHP29 RHP28 RHP27 RHP26 RHP25 RHP24 RHPD7 RHPD6 RHPD5 RHPD4 RHPD3 RHPD2 RHPD1 RHPD0 RHPD15 RHPD14 RHPD13 RHPD12 RHPD11 RHPD10 RHPD9 RHPD8 RHPD23 RHPD22 RHPD21 RHPD20 RHPD19 RHPD18 RHPD17 RHPD16 RHPD31 RHPD30 RHPD29 RHPD28 RHPD27 RHPD26 RHPD25 RHPD24 RLT7 RLT6 RLT5 RLT4 RLT3 RLT2 RLT1 RLT0 RLT15 RLT14 RLT13 RLT12 RLT11 RLT10 RLT9 RLT8 -- -- -- -- -- RECC RHPC RCHC -- -- -- -- OOS -- OCD LCD RECL RCHL RIDL RUDL RIVDL RECCL RHPCL RCHCL -- -- -- -- OOSL COCDL OCDCL LCDCL 216 DS3181/DS3182/DS3183/DS3184 Address 16-bit 8-bit KD2 KD2 KD3 KD4 KD4 KD5 KD6 KD6 KD7 KD8 KD8 KD9 KDA KDA KDB KDC KDC KDD KDE KDE KDF KE0 KE0 KE1 KE2 KE2 KE3 KE4 KE4 KE5 KE6 KE6 KE7 KE8- KE8KEE KEF KF0- KF0KFE KFF Register Type CP.RSRIE RW CP.RCCR1 R CP.RCCR2 R CP.RECCR1 R CP.RECCR2 R CP.RHPCR1 R CP.RHPCR2 R CP.RCCCR1 R CP.RCCCR2 R CP.RFCCR1 R CP.RFCCR2 R RESERVED UNUSED Bit 7 Bit 15 Bit 6 Bit 14 Bit 5 Bit 13 Bit 4 Bit 12 Bit 3 Bit 11 Bit 2 Bit 10 Bit 1 Bit 9 Bit 0 Bit 8 RECIE -- RCC7 RCC15 RCC23 -- RECC7 RECC15 RECC23 -- RHPC7 RHPC15 -- RHPC23 RCHC7 RCHC15 RCHC23 -- RFCC7 RFCC15 RFCC23 -- -- -- -- -- RCHIE -- RCC6 RCC14 RCC22 -- RECC6 RECC14 RECC22 -- RHPC6 RHPC14 -- RHPC22 RCHC6 RCHC14 RCHC22 -- RFCC6 RFCC14 RFCC22 -- -- -- -- -- RIDIE -- RCC5 RCC13 RCC21 -- RECC5 RECC13 RECC21 -- RHPC5 RHPC13 -- RHPC21 RCHC5 RCHC13 RCHC21 -- RFCC5 RFCC13 RFCC21 -- -- -- -- -- RUDIE -- RCC4 RCC12 RCC20 -- RECC4 RECC12 RECC20 -- RHPC4 RHPC12 -- RHPC20 RCHC4 RCHC12 RCHC20 -- RFCC4 RFCC12 RFCC20 -- -- -- -- -- RIVDIE OOSIE RCC3 RCC11 RCC19 -- RECC3 RECC11 RECC19 -- RHPC3 RHPC11 -- RHPC19 RCHC3 RCHC11 RCHC19 -- RFCC3 RFCC11 RFCC19 -- -- -- -- -- RECCIE COCDIE RCC2 RCC10 RCC18 -- RECC2 RECC10 RECC18 -- RHPC2 RHPC10 -- RHPC18 RCHC2 RCHC10 RCHC18 -- RFCC2 RFCC10 RFCC18 -- -- -- -- -- RHPCIE OCDCIE RCC1 RCC9 RCC17 -- RECC1 RECC9 RECC17 -- RHPC1 RHPC9 -- RHPC17 RCHC1 RCHC9 RCHC17 -- RFCC1 RFCC9 RFCC17 -- -- -- -- -- RCHCIE LCDCIE RCC0 RCC8 RCC16 -- RECC0 RECC8 RECC16 -- RHPC0 RHPC8 -- RHPC16 RCHC0 RCHC8 RCHC16 -- RFCC0 RFCC8 RFCC16 -- -- -- -- -- Bit 3 Bit 11 Bit 2 Bit 10 Bit 1 Bit 9 Bit 0 Bit 8 RDD RMNS2 RMX2 RMX10 -- -- REPC Reserved REPCL Reserved REPCIE Reserved RPC2 RPC10 RPC18 -- RFPC2 RFPC10 RFPC18 -- RBRE RMNS1 RMX1 RMX9 -- -- RAPC Reserved RAPCL Reserved RAPCIE Reserved RPC1 RPC9 RPC17 -- RFPC1 RFPC9 RFPC17 -- RPTE RMNS0 RMX0 RMX8 -- -- RSPC Reserved RSPCL Reserved RSPCIE Reserved RPC0 RPC8 RPC16 -- RFPC0 RFPC8 RFPC16 -- Table 12-19. Receive Packet Processor Register Bit Map Address 16-bit 8-bit KC0 KC0 KC1 KC2 KC2 KC3 KC4- KC4KCC KCD KCE KCE KCF KD0 KD0 KD1 KD2 KD2 KD3 KD4 KD4 KD5 KD6 KD6 KD7 KD8 KD8 KD9 KDA KDA KDB Register Type PP.RCR RW PP.RMPSC RW RESERVED PP.RSR R PP.RSRL RL PP.RSRIE RW PP.RPCR1 R PP.RPCR2 R PP.RFPCR1 R PP.RFPCR2 R Bit 7 Bit 15 Bit 6 Bit 14 Reserved RMNS7 RMX7 RMX15 -- -- -- -- REPL -- REPIE -- RPC7 RPC15 RPC23 -- RFPC7 RFPC15 RFPC23 -- Reserved RMNS6 RMX6 RMX14 -- -- -- -- RAPL -- RAPIE -- RPC6 RPC14 RPC22 -- RFPC6 RFPC14 RFPC22 -- Bit 5 Bit 13 Bit 4 Bit 12 RFPD RF16 RFED RMNS5 RMNS4 RMNS3 RMX5 RMX4 RMX3 RMX13 RMX12 RMX11 -- -- -- -- -- -- -- -- -- -- -- Reserved RIPDL RSPDL RLPDL -- -- Reserved RIPDIE RSPDIE RLPDIE -- -- Reserved RPC5 RPC4 RPC3 RPC13 RPC12 RPC11 RPC21 RPC20 RPC19 -- -- -- RFPC5 RFPC4 RFPC3 RFPC13 RFPC12 RFPC11 RFPC21 RFPC20 RFPC19 -- -- -- 217 DS3181/DS3182/DS3183/DS3184 Address 16-bit 8-bit KDC KDC KDD KDE KDE KDF KE0 KE0 KE1 KE2 KE2 KE3 KE4- KE4 KE6 KE7 KE8 KE8 KE9 KEA KEA KEB KEC KEC KED KEE KEE KEF KF0- KF0KFE KFF Register Type PP.RAPCR1 R PP.RAPCR2 R PP.RSPCR1 R PP.RSPCR2 R RESERVED PP.RBCR1 R PP.RBCR2 R PP.REBCR1 R PP.REBCR2 R UNUSED Bit 7 Bit 15 Bit 6 Bit 14 Bit 5 Bit 13 Bit 4 Bit 12 Bit 3 Bit 11 Bit 2 Bit 10 Bit 1 Bit 9 Bit 0 Bit 8 RAPC7 RAPC15 RAPC23 -- RSPC7 RSPC15 RSPC23 -- -- -- RBC7 RBC15 RBC23 RBC31 REBC7 REBC15 REBC23 REBC31 -- -- RAPC6 RAPC14 RAPC22 -- RSPC6 RSPC14 RSPC22 -- -- -- RBC6 RBC14 RBC22 RBC30 REBC6 REBC14 REBC22 REBC30 -- -- RAPC5 RAPC13 RAPC21 -- RSPC5 RSPC13 RSPC21 -- -- -- RBC5 RBC13 RBC21 RBC29 REBC5 REBC13 REBC21 REBC29 -- -- RAPC4 RAPC12 RAPC20 -- RSPC4 RSPC12 RSPC20 -- -- -- RBC4 RBC12 RBC20 RBC28 REBC4 REBC12 REBC20 REBC28 -- -- RAPC3 RAPC11 RAPC19 -- RSPC3 RSPC11 RSPC19 -- -- -- RBC3 RBC11 RBC19 RBC27 REBC3 REBC11 REBC19 REBC27 -- -- RAPC2 RAPC10 RAPC18 -- RSPC2 RSPC10 RSPC18 -- -- -- RBC2 RBC10 RBC18 RBC26 REBC2 REBC10 REBC18 REBC26 -- -- RAPC1 RAPC9 RAPC17 -- RSPC1 RSPC9 RSPC17 -- -- -- RBC1 RBC9 RBC17 RBC25 REBC1 REBC9 REBC17 REBC25 -- -- RAPC0 RAPC8 RAPC16 -- RSPC0 RSPC8 RSPC16 -- -- -- RBC0 RBC8 RBC16 RBC24 REBC0 REBC8 REBC16 REBC24 -- -- Bits that are underlined are read-only; all other bits are read-write. 218 DS3181/DS3182/DS3183/DS3184 12.2 Global Registers Table 12-20. Global Register Map ADDRESS 000h 002h 004h 006h 008h 00Ah 00Ch 00Eh 010h 012h 014h 016h 018h 01Ah 01Ch 01Eh REGISTER GL.IDR GL.CR1 GL.CR2 -- -- GL.GIOCR -- -- GL.ISR GL.ISRIE GL.SR GL.SRL GL.SRIE -- GL.GIORR -- REGISTER DESCRIPTION Global ID Register Global Control Register 1 Global Control Register 2 Unused Unused Global General-Purpose IO Control Register Unused Unused Global Interrupt Status Register Global Interrupt Status Register Interrupt Enable Global Status Register Global Status Register Latched Global Status Register Interrupt Enable Unused Global General-Purpose IO Read register Unused 12.2.1 Register Bit Descriptions Register Name: Register Description: Register Address: GL.IDR Global ID Register 000h Bit # Name 15 ID15 14 ID14 13 ID13 12 ID12 11 ID11 10 ID10 9 ID9 8 ID8 Bit # Name 7 ID7 6 ID6 5 ID5 4 ID4 3 ID3 2 ID2 1 ID1 0 ID0 Bits 15 to 12: Device REV ID Bits 15 to 12 (ID15 to ID12). These bits of the device ID register has same information as the four bits of JTAG REV ID portion of the JTAG ID register. JTAG ID[31:28]. Bits 11 to 0: Device CODE ID Bits 11 to 0 (ID11 to ID0). These bits of the device code ID register has same information as the lower 12 bits of JTAG CODE ID portion of the JTAG ID register. JTAG ID[23:12]. 219 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: GL.CR1 Global Control Register 1 002h Bit # Name Default 15 GWRM 0 14 INTM 0 13 DIREN 0 12 -- 0 11 SIW1 0 10 SIW0 0 9 SIM1 0 8 SIM0 0 Bit # Name Default 7 TMEI 0 6 MEIMS 0 5 GPM1 0 4 GPM0 0 3 PMU 0 2 LSBCRE 0 1 RSTDP 1 0 RST 0 Bit 15: Global Write Mode (GWRM) This bit enables the global write mode. When this bit is set, a write to the register of any port will write to the same register in all the ports. Reading the registers of any port is not supported and will read back undefined data. 0 = Normal write mode 1 = Global write mode Bit 14: INT pin mode (INTM) This bit determines the inactive mode of the INT pin. The INT pin always drives low when active. 0 = Pin is high impedance when not active 1 = Pin drives high when not active Bit 13: Direct Status Enable (DIREN) This bit selects between the direct status and polled status modes for UTOPIA and POS-PHY. 0 = Polled status mode 1 = Direct status mode Bits 11 and 10: System Interface Bus Width (SIW[1:0]) These bits configure the system bus width. 00 = 8-bit 01 = 16-bit 1X = 32-bit Bits 9 and 8: System Interface Mode (SIM[1:0]) These bits configure the system bus mode. 00 = UTOPIA L2 01 = UTOPIA L3 10 = POS-PHY L2 11 = POS-PHY L3 or SPI-3 Bit 7: Transmit Manual Error Insert (TMEI) This bit is used insert an error in all ports and error insertion logic configured for global error insertion. An error(s) is inserted at the next opportunity when this bit transitions from low to high. The GL.CR1.MEIMS bit must be clear for this bit to operate. Bit 6: Transmit Manual Error Insert Select (MEIMS) This bit is used to select the source of the global manual error insertion signal 0 = Global error insertion using TMEI bit 1 = Global error insertion using the GPIO6 pin Bits 5 and 4: Global Performance Monitor Update Mode (GPM[1:0]) These bits select the global performance monitor register update mode. 00 = Global PM update using the PMU bit 01 = Global PM update using the GPIO8 pin 1x = One second PM update using the internal one second counter Bit 3: Global Performance Monitor Update Register (PMU) This bit is used to update all of the performance monitor registers configured to use this bit. When this bit is toggled from low to high the performance registers configured to use this signal will be updated with the latest count value from the counters, and the counters will be reset. The bit should remain high until the performance register update status bit (GL.SR.PMS) goes high, then it should be brought back low which clears the PMS status bit. 220 DS3181/DS3182/DS3183/DS3184 Bit 2: Latched Status Bit Clear on Read Enable (LSBCRE). This signal determines when latched status register bits are cleared. 0 = Latched status register bits are cleared on a write 1 = Latched status register bits are cleared on a read Bit 1: Reset Data Path (RSTDP). When this bit is set, it will force all of the internal data path registers in all ports to their default state. This bit must be set high for a minimum of 100ns. See Section 10.3. Note: The default state is a 1 (after a general reset, this bit will be set to one). 0 = Normal operation 1 = Force all data path registers to their default values Bit 0: Reset (RST). When this bit is set, all of the internal data path and status and control registers (except this RST bit), on all of the ports, will be reset to their default state. This bit must be set high for a minimum of 100ns. See Section 10.3. 0 = Normal operation 1 = Force all internal registers to their default values Register Name: Register Description: Register Address: GL.CR2 Global Control Register 2 004h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 G8KRS2 0 11 G8KRS1 0 10 G8KRS0 0 9 G8K0S 0 8 G8KIS 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 -- 0 3 CLAD3 0 2 CLAD2 0 1 CLAD1 0 0 CLAD0 0 Bits 12 to 10: Global 8KHz Reference Source [2:0] (G8KRS[2:0]). These bits determine the source for the internally generated 8 kHz reference as well as the internal one-second reference, which is derived from the Global 8kHz reference. The source is selected from one of the CLAD clocks or from one of the port 8KREF clock sources. These bits are ignored when the G8KIS bit = 1. See Table 10-12. Bit 9: Global 8KHz Reference Output Select (G8KOS). This bit determines whether GPIO2 pin is used for the global 8KREFO output signal, or is used as specified by GL.GIOCR.GPIO2S[1:0]. 0 = GPIO2 pin mode selected by GL.GIOCR.GPIO2S[1:0] 1 = GPIO2 is the global 8KREFO output signal selected by GL.CR2.8KRS[2:0] Bit 8: Global 8KHz Reference Input Select (G8KIS). This bit determines whether GPIO4 pin is used for the global 8KREFI input signal, or is used as specified by GL.GIOCR.GPIO4S[1:0]. G8KREFI signal will be low if not selected. Global 8KREF pin signal will be low if not selected. 0 = GPIO4 pin mode selected by GL.GIOCR.GPIO4S[1:0] 1 = GPIO4 is the global 8KREFI input signal for one second timer and ports to use Bits 3 to 0: CLAD IO Mode [3:0] (CLAD[3:0]). These bits control the CLAD clock IO pins CLKA, CLKB and CLKC. Note: These bits control which clock is used to recover the RX Clock from the line in the LIU. See Table 10-11. 221 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: GL.GIOCR Global General-Purpose IO Control Register 00Ah Bit # Name Default 15 GPIO8S1 0 14 GPIO8S0 0 13 GPIO7S1 0 12 GPIO7S0 0 11 GPIO6S1 0 10 GPIO6S0 0 9 GPIO5S1 0 8 GPIO5S0 0 Bit # Name Default 7 GPIO4S1 0 6 GPIO4S0 0 5 GPIO3S1 0 4 GPIO3S0 0 3 GPIO2S1 0 2 GPIO2S0 0 1 GPIO1S1 0 0 GPIO1S0 0 Bits 15 to 14: General-Purpose IO 8 Select [1:0] (GPIO8S[1:0]). These bits determine the function of the GPIO8 pin. These selections are only valid if GL.CR1.GPM[1:0] is not set to 01. 00 = Input 01 = Port 4 B status output selected by PORT.CR4:GPIOB[3:0] in port control registers 10 = Output logic 0 11 = Output logic 1 Bits 13 to 12: General-Purpose IO 7 Select [1:0] (GPIO7S[1:0]). These bits determine the function of the GPIO7 pin. 00 = Input 01 = Port 4 A status output selected by PORT.CR4:GPIOA[3:0] in port control registers 10 = Output logic 0 11 = Output logic 1 Bits 11 to 10: General-Purpose IO 6 Select [1:0] (GPIO6S[1:0]). These bits determine the function of the GPIO6 pin. These selections are only valid if GL.CR1.MEIMS=0. 00 = Input 01 = Port 3 B status output selected by PORT.CR4:GPIOB[3:0] in port control registers 10 = Output logic 0 11 = Output logic 1 Bits 9 to 8: General-Purpose IO 5 Select [1:0] (GPIO5S[1:0]). These bits determine the function of the GPIO5 pin. 00 = Input 01 = Port 3 A status output selected by PORT.CR4:GPIOA[3:0] in port control registers 10 = Output logic 0 11 = Output logic 1 Bits 7 to 6: General-Purpose IO 4 Select [1:0] (GPIO4S[1:0]). These bits determine the function of the GPIO4 pin. These selections are only valid if GL.CR2 .G8KRIS=0. 00 = Input 01 = Port 2 B status output selected by PORT.CR4:GPIOB[3:0] in port control registers 10 = Output logic 0 11 = Output logic 1 Bits 5 to 4: General-Purpose IO 3 Select [1:0] (GPIO3S[1:0]). These bits determine the function of the GPIO3 pin. 00 = Input 01 = Port 2 A status output selected by PORT.CR4:GPIOA[3:0] in port control registers 10 = Output logic 0 11 = Output logic 1 Bits 3 to 2: General-Purpose IO 2 Select [1:0] (GPIO2S[1:0]). These bits determine the function of the GPIO2 pin. These selections are only valid if GL.CR2.GKROS=0. 00 = Input 01 = Port 1 B status output selected by PORT.CR4:GPIOB[3:0] in port control registers 10 = Output logic 0 11 = Output logic 1 222 DS3181/DS3182/DS3183/DS3184 Bits 1 to 0: General-Purpose IO 1 Select [1:0] (GPIO1S[1:0]). These bits determine the function of the GPIO1 pin. 00 = Input 01 = Port 1 A status output selected by PORT.CR4:GPIOA[3:0] in port control registers 10 = Output logic 0 11 = Output logic 1 Register Name: Register Description: Register Address: GL.ISR Global Interrupt Status Register 010h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 PISR4 6 PISR3 5 PISR2 4 PISR1 3 -- 2 -- 1 TSSR 0 GSR Bits 15 to 8: Not Used (--) Bits 7 to 4: Port Interrupt Status Register [4:1] (PISR[4:1] ) The corresponding bit is set when any of the bits in the port interrupt status registers (PORT.ISR) are set. The INT interrupt pin will be driven low when any bit is set and the corresponding GL.ISRIE.PISRIE[4:1] interrupt enable bit is enabled. Bit 1: Transmit System Interface Status Register Interrupt Status (TSSR) This bit is set when any of the latched status register bits in the transmit system interface are set and enabled for interrupt. The INT pin will be driven low when this bit is set and the GL.ISRIE.TSSRIE interrupt enable bit is enabled. Bit 0: Global Status Register Interrupt Status (GSR) This bit is set when any of the latched status register bits in the global latched status register (GL.SRL) are set and enabled for interrupt. The INT interrupt pin will be driven low when this bit is set and the GL.ISRIE.GSRIE interrupt enable bit is enabled. 223 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: GL.ISRIE Global Interrupt Status Register Interrupt Enable 012h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 PISRIE4 0 6 PISRIE3 0 5 PISRIE2 0 4 PISRIE1 0 3 -- 0 2 -- 0 1 TSSRIE 0 0 GSRIE 0 Bits 15 to 8: Not Used (--) Bits 7 to 4: Port Interrupt Status Register Interrupt Enable [4:1] (PISRIE[4:1]) When any interrupt enable bit in this group is enabled corresponding to a status bit set in the GL.ISR.PISR[4:1] status bit group, the INT pin will be driven low. 0 = interrupt disabled 1 = interrupt enabled Bit 1: Transmit System Interface Status Register Interrupt Status Interrupt Enable (TSSRIE). When this bit is enabled, and the GL.ISR.TSSR status bit is set, the INT pin will be driven low. 0 = interrupt disabled 1 = interrupt enabled Bit 0: Global Status Register Interrupt Status Interrupt Enable (GSRIE) When this interrupt enable bit is enabled, and the GL.ISR.GSR status bit is set, the INT pin will be driven low. 0 = interrupt disabled 1 = interrupt enabled Register Name: Register Description: Register Address: GL.SR Global Status Register 014h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 -- 6 -- 5 -- 4 -- 3 -- 2 -- 1 CLOL 0 GPMS Bit 1: CLAD Loss of Lock (CLOL) - This bit is set when any of the PLLs in the CLAD are not locked to the reference frequency. Bit 0: Global Performance Monitoring Update Status (GPMS) This bit is set when all of the port performance register update status bits (PORT.SR.PMS), that are enabled for global update control (PORT.CR1.PMUM=1), are set. It is an "AND" of all the globally enabled port PMU status bits. In global software update mode, the global update request bit (GL.CR1.PMU) should be held high until this status bit goes high. 0 = The associated update request signal is low or not all register updates are completed 1 = The requested performance register updates are all completed 224 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: GL.SRL Global Status Register Latched 016h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 -- 6 -- 5 -- 4 8KREFL 3 CLADL 2 ONESL 1 CLOLL 0 GPMSL Bit 4: 8K Reference Activity Status Latched (8KREFL) This bit will be set when the 8 kHz reference signal on the GPIO4 pin is active. The GL.CR2.G8KIS bit must be set for the activity to be monitored. Bit 3: CLAD Reference Clock Activity Status Latched (CLADL) This bit will be set when the CLAD PLL reference clock signal on the CLKA pin is active. Bit 2: One Second Status Latched (ONESL) This bit will be set once a second. The GL.ISR.GSR status bit will be set when this bit is set and the GL.SRIE.ONESIE bit is enabled. The INT pin will be driven low if this bit is set and the GL.SRIE.ONESIE bit and the GL.ISRIE.GSRIE bit are enabled. Bit 1: CLAD Loss Of Lock Latched (CLOLL) This bit will be set when the GL.SR.CLOL status bit changes from low to high. The GL.ISR.GSR bit will be set when this bit is set and the GL.SRIE.CLOLIE bit is set and the INT pin will be driven low if the GL.ISRIE.GSRIE bit is also enabled. Bit 0: Global Performance Monitoring Update Status Latched (GPMSL) This bit will be set when the GL.SR.GPMS status bit changes from low to high. This bit will set the GL.ISR.GSR status bit if the GL.SRIE.GPMSIE is enabled. This bit will drive the interrupt pin low if the GL.SRIE.GPMSIE bit and the GL.ISRIE.GSRIE bit are enabled. Register Name: Register Description: Register Address: GL.SRIE Global Status Register Interrupt Enable 018h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 -- 0 3 -- 0 2 ONESIE 0 1 CLOLIE 0 0 GPMSIE 0 Bit 2: One-Second Interrupt Enable (ONESIE) This bit will drive the interrupt pin low when this bit is enabled, the GL.SRL.ONESL bit is set, and the GL.ISRIE.GSRIE bit is enabled. 0 = interrupt disabled 1 = interrupt enabled Bit 1: CLAD Loss Of Lock Interrupt Enable (CLOLIE) The interrupt pin will be driven when this bit is enabled, the GL.SRL.CLOLL is set, and GL.ISRIE.GSRIE bit is enabled. 0 = interrupt disabled 1 = interrupt enabled Bit 0: Global Performance Monitoring Update Status Interrupt Enable (GPMSIE) The interrupt pin will be driven when this bit is enabled and the GL.SRL.GPMSL bit is set and the GL.ISRIE.GSRIE bit is enabled. 0 = interrupt disabled 1 = interrupt enabled 225 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: GL.GIORR Global General-Purpose IO Read Register 01Ch Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 GPIO8 6 GPIO7 5 GPIO6 4 GPIO5 3 GPIO4 2 GPIO3 1 GPIO2 0 GPIO1 Bits 7 to 0: General-Purpose IO Status [8:1]] (GPIO[8:1] ) These bits reflect the input or output signal on the 8 general-purpose IO pins. 226 DS3181/DS3182/DS3183/DS3184 12.3 UTOPIA/POS-PHY System Interface 12.3.1 Transmit System Interface The transmit system interface block has three registers. 12.3.1.1 Register Map Table 12-21. Transmit System Interface Register Map ADDRESS 030h 032h 034h 036h REGISTER SI.TCR SI.TSRL SI.TSRIE -- REGISTER DESCRIPTION System Interface Transmit Control Register System Interface Transmit Status Register Latched System Interface Transmit Status Register Interrupt Enable Unused 12.3.1.2 Register Bit Descriptions Register Name: Register Description: Register Address: SI.TCR System Interface Transmit Control Register 030h Bit # Name Default 15 -- 0 14 -- 0 13 TXAD5 0 12 TXAD4 0 11 TXAD3 0 10 TXAD2 0 9 TXAD1 0 8 TXAD0 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 -- 0 3 TPARP 0 2 TFLVI 0 1 TSBRE 0 0 THECT 0 Bits 13 to 8: Transmit Cell/Packet Available Deassertion Time (TXAD[5:0]) - These six bits indicate the amount of data that can be transferred after the cell/packet available signal is deasserted. If more than the indicated amount of data is transferred, a Transmit FIFO overflow may occur. In UTOPIA mode, only TXAD[2:0] are valid, and they indicate the number of transfers into the FIFO before the Transmit FIFO is full. For UTOPIA Level 2, a value of 00h enables the default mode, which is 5 (TDXA will transition low on the edge that samples payload byte 43 in 8-bit mode, payload bytes 37 and 38 in 16-bit mode, and payload bytes 25, 26, 27, and 28 in 32-bit mode). For UTOPIA Level 3, a value of 00h or 01h enables the default mode. The default for UTOPIA Level 3 is for TDXA to transition low on the clock edge following the edge that samples the start of a cell. In POS-PHY mode, TXAD[5:0] indicate the number four byte data groups that can be written into the Transmit FIFO before it is full (maximum value 56 or 38h). In POS-PHY Level 2, a value of 00h enables the default mode, which is 1 (For an x-byte transfer, TDXA and TSPA will transition low on the edge that samples byte x-4 in 8-bit mode, bytes x-5 and x-4 in 16-bit mode, and bytes x-7, x-6, x-5, and x-4 in 32-bit mode). In POS-PHY Level 3 (or SPI-3) 8-bit, a value of 00h enables the default mode, which is 1 (For a x-byte transfer, TDXA and TSPA will transition low on the edge that samples byte x-4). For POS-PHY Level 3 (or SPI-3) 16-bit and 32-bit mode, a value of 00h or 01h enables the default mode, which is 2 (For an x-byte transfer, TDXA and TSPA will transition low on the edge that samples bytes x-9 and x-8 in 16-bit mode and bytes x-11, x-10, x-9, and x-8 in 32-bit mode). Note: A packet that is 4x+1, 4x+2, 4x+3, or 4x+4 (where x is an integer) bytes long consumes x+1 four byte data groups of space in the FIFO. This includes 2-byte and 3-byte packets, which consume a four-byte data group of space in the FIFO. Bit 3: Transmit System Parity Polarity (TPARP) - When 0, the TPAR signal will maintain odd parity (for all 0''s, TPAR is high). When 1, the TPAR signal will maintain even parity (for all 0''s, TPAR is low). 227 DS3181/DS3182/DS3183/DS3184 Bit 2: Transmit System Fill Level Inversion (TFLVI) - When 0, the polarity of the TPXA, TDXA, and TSPA signals will be normal (high for data available). When 1, the polarity of the TPXA, TDXA, and TSPA signals will be inverted (low for data available). Bit 1: Transmit System Interface Byte Reordering Enable (TSBRE) - When 0, byte reordering is disabled, and the first byte transmitted is transferred across the system interface as the most significant byte (TDATA[31:24] in 32-bit mode or TDATA[15:8] in 16-bit mode). When 1, byte reordering is enabled, and the first byte transmitted is transferred across the system interface as the least significant byte (TDATA[7:0]). Bit 0: Transmit System HEC Transfer (THECT) - When 0, The HEC byte is not transferred across the transmit system interface. When 1, the HEC byte is transferred across the transmit system interface with the cell data. Register Name: Register Description: Register Address: SI.TSRL System Interface Transmit Status Register Latched 032h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 -- 6 -- 5 -- 4 -- 3 -- 2 -- 1 TSCLKAL 0 TPREL Bit 1: Transmit System Interface Clock Active (TSCLKAL) - This bit is set when TSCLK is active. Bit 0: Transmit System Interface Parity Error Latched (TPREL) - This bit is set when a parity error is detected during a data transfer on the Transmit System Interface bus. Register Name: Register Description: Register Address: SI.TSRIE System Interface Transmit Status Register Interrupt Enable 034h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 -- 0 3 -- 0 2 -- 0 1 -- 0 0 TPREIE 0 Bit 0: Transmit System Interface Parity Error Interrupt Enable (TPREIE) - This bit enables an interrupt if the TPREL bit in the TSISRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled 228 DS3181/DS3182/DS3183/DS3184 12.3.2 Receive System Interface Register Map The receive system interface block has three registers. Table 12-22. Receive System Interface Register Map ADDRESS REGISTER 038h 03Ah 03Ch 03Eh SI.RCR1 SI.RCR2 SI.RSRL -- REGISTER DESCRIPTION System Interface Receive Control Register 1 System Interface Receive Control Register 2 System Interface Receive Status Register Latched Unused 12.3.2.1 Register Bit Descriptions Register Name: Register Description: Register Address: SI.RCR1 System Interface Receive Control Register 1 038h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 RMDT2 0 9 RMDT1 0 8 RMDT0 0 Bit # Name Default 7 -- 0 6 RXAD2 0 5 RXAD1 0 4 RXAD0 0 3 RPARP 0 2 RFLVI 0 1 RSBRE 0 0 RHECT 0 Bits 10 to 8: Receive System RVAL Minimum Deassertion Time (RMDT[2:0]) - These three bits indicate the minimum number of clock cycles that RVAL must remain deasserted between packets transferred from the same port, a transfer of data equal to the maximum burst depth length (if enabled), or before RSX can be asserted. A value of zero, means that RVAL will not deassert between packets transferred from the same port or between transfers of the maximum burst length when no other port has data available. These bits are ignored in UTOPIA and POS-PHY Level 2 modes. Note: The RVAL minimum deassertion time is for optionally extending the time between packet transfers and port changes to allow a POS-PHY Level 3 Link Layer device enough time to deassert REN and pause the next data transfer. Bits 6 to 4: Receive Cell Available Deassertion Time (RXAD[2:0]) - These three bits indicate the number of transfers that will occur after the selected Receive FIFO indicates it is "empty". A value of 000, enables the default mode. The default for UTOPIA Level 2 is 0 (RDXA will transition low on the clock edge following the clock edge that outputs payload byte 48 in 8-bit mode, payload bytes 47 and 48 in 16-bit mode, and payload bytes 45, 46, 47, and 48 in 32-bit mode). The default for UTOPIA Level 3 is for RDXA to transition low on the clock edge that outputs the start of cell. These bits are ignored in POS-PHY mode. Bit 3: Receive System Parity Polarity (RPARP) - When 0, the RPRTY signal will maintain odd parity (for all 0''s, RPRTY is high). When 1, the RPRTY signal will maintain even parity (for all 0''s, RPRTY is low). Bit 2: Receive System Fill Level Inversion (RFLVI) - When 0, the polarity of the RPXA and RDXA signals will be normal (high for data available). When 1, the polarity of the RPXA and RDXA signals will be inverted (low for data available). Bit 1: Receive System Interface Byte Reordering Enable (RSBRE) - When 0, byte reordering is disabled, and the first byte received is transferred across the system interface as the most significant byte (RDATA[31:24] in 32bit mode or RDATA[15:8] in 16-bit mode). When 1, byte reordering is enabled, and the first byte received is transferred across the system interface as the least significant byte (RDATA[7:0]). Bit 0: Receive System HEC Transfer Enable (RHECT) - When 0, The HEC byte is not transferred across the receive system interface. When 1, the HEC byte is transferred across the receive system interface with the cell data. 229 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: SI.RCR2 System Interface Receive Control Register 2 03Ah Bit # Name Default 15 -- 0 14 -- 0 13 RMBL5 0 12 RMBL4 0 11 RMBL3 0 10 RMBL2 0 9 RMBL1 0 8 RMBL0 0 Bit # Name Default 7 RLBL7 0 6 RLBL6 0 5 RLBL5 0 4 RLBL4 0 3 RLBL3 0 2 RLBL2 0 1 RLBL1 0 0 RLBL0 0 Bits 13 to 8: Receive Maximum Burst Length (RMBL[5:0]) - In POS-PHY Level 3, these six bits limit the maximum number of four byte data groups that can be transferred from a port before switching to another port. The maximum number of transfers is RMBL[5:0]+1 in 32-bit mode, 2 x (RMBL[5:0]+1} in 16-bit mode, and 4*(RMBL[5:0]+1} in 8-bit mode. Note: if no other port is ready to start a transfer, transfer from the current port will continue if the port contains more data than the almost empty level or contains an end of packet. These bits are ignored in POS-PHY Level 2 or UTOPIA mode. A value of 00h disables the maximum burst length. In 32-bit mode, a value of 01h is treated as 02h. Bits 7 to 0: Receive System Loopback Bandwidth Limit (RLBL[7:0]) - These eight bits limit the maximum bandwidth of a single port during system loopback. For RLBL[7:0] equals x, the bandwidth will be limited to 1/x of the maximum system interface bandwidth. In 8-bit and 16-bit mode, a value of 00h is treated as 01h. In 32-bit mode, a value of 01h or 00h is treated as 02h. Register Name: Register Description: Register Address: SI.RSRL System Interface Receive Status Register Latched 03Ch Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 -- 6 -- 5 -- 4 -- 3 -- 2 -- 1 -- 0 RSCLKAL Bit 0: Receive System Interface Clock Active Latched (RSCLKAL) - This bit is set when RSCLK is active. 230 DS3181/DS3182/DS3183/DS3184 12.4 Per-Port Common 12.4.1 Per-Port Common Register Map Table 12-23. Per-Port Common Register Map ADDRESS (0,2,4,6)40h (0,2,4,6)42h (0,2,4,6)44h (0,2,4,6)46h (0,2,4,6)48h (0,2,4,6)4Ah (0,2,4,6)4Ch (0,2,4,6)4Eh (0,2,4,6)50h (0,2,4,6)52h (0,2,4,6)54h (0,2,4,6)56h (0,2,4,6)58h (0,2,4,6)5Ah (0,2,4,6)5Ch (0,2,4,6)5Eh REGISTER PORT.CR1 PORT.CR2 PORT.CR3 PORT.CR4 -- PORT.INV1 PORTINV2 -- PORT.ISR PORT.SR PORT.SRL PORT.SRIE -- -- -- -- REGISTER DESCRIPTION Port Control Register 1 Port Control Register 2 Port Control Register 3 Port Control Register 4 Unused Port IO Invert Control Register 1 Port IO Invert Control Register 2 Unused Port Interrupt Status Register Port Status Register Port Status Register Latched Port Status Register Interrupt Enable Unused Unused Unused Unused 12.4.2 Per-Port Common Register Bit Descriptions Register Name: Register Description: Register Address: PORT.CR1 Port Control Register 1 (0,2,4,6)40h Bit # Name Default 15 NAD 0 14 PAIS2 0 13 PAIS1 0 12 PAIS0 0 11 LAIS1 0 10 LAIS0 0 9 BENA 0 8 HDSEL 0 Bit # Name Default 7 TMEI 0 6 MEIM 0 5 -- -- 4 PMUM 0 3 PMU 0 2 PD 1 1 RSTDP 1 0 RST 0 Bit 15: Nibble Align Disable (NAD). This bit is used to disable the nibble alignment of the transmit ATM cells in direct mapped DS3 or E3 G.832 framing modes. It must be set when in DS3 M23 mode and the C-bits are used for ATM payload. 0 = Nibble alignment enabled 1 = Nibble alignment disabled Bits 14 to 12: Payload AIS Select [2:0] (PAIS[2:0]). This bit controls when an unframed all ones signal is forced on the receive data path after the receive framer and payload loopback mux. Default: Payload AIS always sent. See Table 10-19. Bits 11 to 10: Line AIS Select [1:0] (LAIS[1:0). These bits control when a DS3 framed AIS or an unframed all ones signal is to be transmitted on TPOSn/TNEGn and/or TXPn/TXNn. The signal on TPOSn/TNEGn can be AMI or unipolar. This signal is sent even when in diagnostic loopback and always over-rides signals from the framers. Default: AIS sent if DLB is enabled. See Table 10-18. Bit 9: BERT Enable (BENA). This bit is used to enable the BERT logic. The BERT pattern will be the payload data replacing the cell or packet data from the system interface. 0 = BERT logic disabled and powered down 1 = BERT logic enabled 231 DS3181/DS3182/DS3183/DS3184 Note: Data on the receive side will flow to the Cell/Packet processor regardless of the setting of BENA. The packet processor could detect packets even if not desired. To disable possible packets on the system interface, set the FIFO.RCR.RFRST bit. Bit 8: HDLC Select (HDSEL). This bit is used to select the source of the receive HDLC controller and the destination of the transmit HDLC controller when in DS3 or E3 PLCP mode. When not in any PLCP mode, this bit has no meaning and the HDLC controllers are connected to the DS3 or E3 framers if in DS3 or E3 mode. 0 = Connect HDLC controller to DS3 or E3 framers 1 = Connect HDLC controller to PLCP framers Bit 7: Transmit Manual Error Insert (TMEI) This bit is used to insert errors in all error insertion logic configured to use this bit when PORT.CR1.MEIM=0. The error(s) will be inserted when this bit is toggled low to high. Bit 6: Transmit Manual Error Insert Mode (MEIM). These bits select the method transmit manual error insertion for this port for error generators configured to use the external TMEI signal. The global updates are controlled by the GL.CR1.MEIMS bit. 0 = Port software update via PORT.CR1.TMEI 1 = Global update source Bit 4: Performance Monitor Update Mode (PMUM). These bits select the method of updating the performance monitor registers. The global updates are controlled by the GL.CR1.GPM[1:0] bits. 0 = Port software update 1 = Global update Bit 3: Performance Monitor Register Update (PMU) This bit is used to update all of the performance monitor registers configured to use this bit when PORT.CR1.PMUM=0. The performance registers configured to use this signal will be updated with the latest count value and the counters reset when this bit is toggled low to high. The bit should remain high until the performance register update status bit (PORT.SR.PMS) goes high, then it should be brought back low which clears the PMS status bit. Bit 2: Power-Down (PD). When this bit is set, the LIU and digital logic for this port are powered down and considered "out of service." The logic is powered down by stopping the clocks. See Section 10.3. 0 = Normal operation 1 = Power-down port circuits (default state) Bit 1: Reset Data Path (RSTDP). When this bit is set, it will force all of the internal data path registers in this port to their default state. This bit must be set high for a minimum of 100ns and then set back low. See Section 10.3. Note: The Default State of this bit is 1 (after a general reset (port or global), this bit will be set to one). 0 = Normal operation 1 = Force all data path registers to their default values Bit 0: Reset (RST). When this bit is set, it will force all of the internal data path and status and control registers (except this RST bit) of this port to their default state. See Section 10.3. This bit must be set high for a minimum of 100ns and then set back low. This software bit is logically ORed with the inverted hardware signal RST and the GL.CR1.RST bit. 0 = Normal operation 1 = Force all internal registers to their default values 232 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PORT.CR2 Port Control Register 2 (0,2,4,6)42h Bit # Name Default 15 TLEN 0 14 TTS 0 13 RMON 0 12 TLBO 0 11 RCDV8 0 10 LM2 0 9 LM1 0 8 LM0 0 Bit # Name Default 7 RCDIS 0 6 PMCPE 0 5 FM5 0 4 FM4 0 3 FM3 0 2 FM2 0 1 FM1 0 0 FM0 0 Bit 15: Transmit Line IO Signal Enable (TLEN). This bit is used to enable to transmit line interface output pins TLCLKn, TPOSn/TDATn and TNEGn. 0 = Disable, force outputs low 1 = Enable normal operation Bit 14: Transmit LIU Tri-State (TTS) This bit is used to tri-state the transmit TXPn and TXNn pins. The LIU is still powered up when the pins are tri-stated. It has no effect when the LIU is disabled and powered down. 0 = TXPn and TXNn driven 1 = TXPn and TXNn tri-stated Bit 13: Receive LIU Monitor Mode (RMON) This bit is used to enable the receive LIU monitor mode pre-amplifier. Enabling the pre-amplifier adds about 20 dB of linear amplification for use in monitor applications where the signal has been reduced 20 dB using resistive attenuator circuits. 0 = Disable the 20 dB pre-amp 1 = Enable the 20 dB pre-amp Bit 12: Transmit LIU LBO (TLBO) This bit is used enable the transmit LBO circuit which causes the transmit signal to have a wave shape that approximates about 225 feet of cable. This is used to reduce near end crosstalk when the cable lengths are short. This signal is only valid in DS3 and STS-1 LIU modes. 0 = TXPn and TXNn have full amplitude signals 1 = TXPn and TXNn signals approximate 225 feet of cable Bit 11: Receive ATM Cell Delineation Verify 8 Enable (RCDV8). This bit determines the number of good cells required for the ATM cell delineator state machine to transition from the "Verify" state to the "Update" state. This setting also determines how many valid cells required to clear the OCD status bit. 0 = Six valid ATM cells are required (typical for framed cells) 1 = Eight valid ATM cells are required (typical for unframed cells) Bits 10 to 8: Port Interface Mode (LM[2:0]). The LM[2:0] bits select main port interface operational modes. The default state disables the LIU and the JA. See Table 10-33. Bit 7: Receive Cell Delineator Disable (RCDIS). This bit determines if the ATM cell delineator in the ATM cell processor is active in PLCP modes. This ATM cell delineator in the ATM cell processor is always active in nonPLCP ATM cell modes. 0 = ATM cell delineation is determined in the ATM cell processor 1 = ATM cell delineation is determined in the PLCP framer Note: RCDIS = 1 is not a recommended mode. Bit 6: POS-PHY Mode Cell Processor Enable (PMCPE). This bit determines the associated transmit and receive port interface processing (cell/packet) to be performed in the POS-PHY mode. It is only active in POS-PHY mode when PLCP is not enabled. When PLCP is enabled in POS-PHY mode, cell processing is performed. 0 = Packet processing will be performed 1 = Cell processing will be performed Bits 5 to 0: Framing mode (FM[5:0]). The FM[5:0] bits select main framing operational modes. Default: DS3 C-bit. See Table 10-32. 233 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PORT.CR3 Port Control Register 3 (0,2,4,6)44h Bit # Name Default 15 -- 0 14 -- 0 13 RCLKS 0 12 RSOFOS 0 11 RPFPE 0 10 TCLKS 0 9 TSOFOS 0 8 TPFPE 0 Bit # Name Default 7 P8KRS1 0 6 P8KRS0 0 5 P8KREF 0 4 LOOPT 0 3 CLADC 0 2 RFTS 0 1 TFTS 0 0 TLTS 0 Bit 13: Receive Clock Output Select (RCLKS). This bit is used to select the function of the RPOHCLKn / RGCLKn / RCLKOn pins. See Table 10-31. 0 = Selects the RGCLKn signal, RPOHCLKn signal, or the drive low pin function. 1 = Selects RCLKOn signal. Bit 12: Receive Start Of Frame Output Select (RSOFOS). This bit is to select the function of the RSOFOn / RDENn pins. See Table 10-30. 0 = Selects RDENn signal. 1 = Selects RSOFOn signal. Bit 11: Receive PLCP/Fractional Port Enable (RPFPE). This bit is used to enable the receive PLCP/Fractional port pins. See tables in Section 10.5.9.2. 0 = Disable receive PLCP/Fractional port pins 1 = Enable receive PLCP/Fractional port pins Bit 10: Transmit Clock Output Select (TCLKS). This bit is used to select the function of the TPOHCLKn / TGCLKn / TCLKOn pins. See Table 10-24. 0 = Selects TGCLKn or TPOHCLKn signal. 1 = Selects TCLKOn signal. Bit 9: Transmit Start Of Frame Output Select (TSOFOS). This bit is used to select the function of the TSOFOn / TDENn pins. See Table 10-23. 0 = Selects TDENn signal. 1 = Selects TSOFOn signal. Bit 8: Transmit PLCP/Fractional Port Enable (TPFPE). This bit is used to enable the transmit PLCP/fractional port pins. See tables in Section 10.5.9.1. 0 = Disable transmit PLCP/Fractional port pins 1 = Enable transmit PLCP/Fractional port pins Bits 7 and 6: Port 8 kHz Reference Source Select [1:0] (P8KRS [1:0]). These bits select the source of the 8 kHz reference from the port sources. The 8K reference for this port can be used as the global 8K reference source. See Table 10-13. Bit 5: Port 8 kHz Reference Source (P8KREF). This bit selects the source of the 8 kHz reference for PLCP trailer operation and one second timer. 0 = 8 kHz reference from global source 1 = 8 kHz reference from this ports selected source Bit 4: Loop Time Enable (LOOPT). When this bit is set, the port is in loop time mode. The transmit clock is set to the receive clock from the RLCLKn pin or the recovered clock from the LIU or the CLAD clock and the TCLKIn pin is not used. This function of this bit is conditional on other control bits. See Table 10-4 for more details. 0 = Normal transmit clock operation 1 = Transmit using the receive clock 234 DS3181/DS3182/DS3183/DS3184 Bit 3: CLAD Transmit Clock Source Control (CLADC). This bit is used to enable the CLAD clocks as the source of the internal transmit clock. This function of this bit is conditional on other control bits. See Table 10-4 for more details. 0 = Use CLAD clocks for the transmit clock as appropriate 1 = Do not use CLAD clocks for the transmit clock - (if no loopback is enabled, TCLKIn is the source) Bit 2: Receive Framer IO Signal Timing Select (RFTS). This bit controls the timing reference for the signals on the receive framer interface IO pins. The pins controlled are RSERn, RSOFOn / RDENn / RFOHENn and RFOHENn. See Table 10-8 for more details. 0 = Use output clocks for timing reference 1 = Use input clocks for timing reference Bit 1: Transmit Framer IO Signal Timing Select (TFTS). This bit controls the timing reference for the signals on the transmit framer interface IO pins. The pins controlled are TOHMIn / TSOFIn, TFOHn / TSERn, TFOHENIn and TSOFOn / TDENn / TFOHENOn. See Table 10-7 for more details. 0 = Use output clocks for timing reference 1 = Use input clocks for timing reference Bit 0: Transmit Line IO Signal Timing Select (TLTS). This bit controls the timing reference for the signals on the transmit line interface IO pins. The pins controlled are TPOSn / TDATn and TNEGn / TOHMOn. See Table 10-6 for more details. 0 = Use output clocks for timing reference 1 = Use input clocks for timing reference 235 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PORT.CR4 Port Control Register 4 (0,2,4,6)46h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 SLB 0 10 LBM2 0 9 LBM1 0 8 LBM0 0 Bit # Name Default 7 GPIOB3 0 6 GPIOB2 0 5 GPIOB1 0 4 GPIOB0 0 3 GPIOA3 0 2 GPIOA2 0 1 GPIOA1 0 0 GPIOA0 0 Bit 11: System Bus Loopback (SLB). This bit enables the system bus loopback mode per port when the bit is set. ATM cells and/or HDLC packets are looped back from the transmit system bus to the receive system bus through the FIFOs. See Figure 10-10 for the block diagram highlighting loopback features. Bits 10 to 8: Loopback Mode [2:0] (LBM[2:0]). These bits select the loopback modes for analog loopback (ALB), line loopback (LLB), payload loopback (PLB) and diagnostic loopback (DLB). See Table 10-17 for the loopback select codes. Default: No Loopback. Bits 7 to 4: General-Purpose IO B Output Select[3:0] (GPIOB[3:0]) These bits determine which alarm status signal to output on the GPIO2(port 1), GPIO4(port 2), GPIO6(port 3) or GPIO8(port 4) pins. The GPIO pin must be enabled by setting the bits in the GL.GIOCR and either GL.CR1 or GL.CR2 registers to output the selected alarm signal. See Table 10-15. See Table 10-16 for the alarm select codes. Bits 3 to 0: General-Purpose IO A Output Select[3:0] (GPIOA[3:0]) These bits determine which alarm status signal to output on the GPIO1(port 1), GPIO3(port 2), GPIO5(port 3) or GPIO7(port 4) pins. The GPIO pin must be enabled for output by setting the bits in the GL.GIOCR register. See Table 10-15 for configuration settings. See Table 10-16 for the alarm select codes. 236 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PORT.INV1 Port IO Invert Control Register 1 (0,2,4,6)4Ah Bit # Name Default 15 TPDEI 0 14 TPDTI 0 13 -- 0 12 TPOHSI 0 11 TPOHEI 0 10 TPOHI 0 9 TOHSI 0 8 TOHEI 0 Bit # Name Default 7 TOHI 0 6 TOHCKI 0 5 TSOFII 0 4 TNEGI 0 3 TPOSI 0 2 TLCKI 0 1 TCKOI 0 0 TCKII 0 Bit 15: TPDENOn Invert (TPDEI). This bit inverts the TPDENOn pin when set. Bit 14: TPDATn Invert (TPDTI). This bit inverts the TPDATn pin when set. Bit 12: TPOHSOFn / TSOFOn / TDENn/ TFOHENOn Invert (TPOHSI). This bit inverts the TPOHSOFn / TSOFOn / TDENn / TFOHENOn pin when set. Bit 11: TPOHENn / TFOHENIn / TPDENIn Invert (TPOHEI). This bit inverts the TPOHENIn / TFOHENIn / TPDENIn pin when set. Bit 10: TPOHn / TFOHn / TSERn Invert (TPOHI). This bit inverts the TPOHn / TFOHn / TSERn pin when set. Bit 9: TOHSOFn Invert (TOHSI). This bit inverts the TOHSOFn pin when set. Bit 8: TOHENn Invert (TOHEI). This bit inverts the TOHENn pin when set. Bit 7: TOHn Invert (TOHI). This bit inverts the TOHn pin when set. Bit 6: TOHCLKn Invert (TOHCKI). This bit inverts the TOHCLKn pin when set. Bit 5: TSOFIn / TOHMIn Invert (TSOFII). This bit inverts the TSOFIn / TOHMIn pin when set. Bit 4: TNEGn / TOHMOn Invert (TNEGI). This bit inverts the TNEGn / TOHMOn pin when set. Bit 3: TPOSn / TDATn Invert (TPOSI). This bit inverts the TPOSn / TDATn pin when set. Bit 2: TLCLKn Invert (TLCKI). This bit inverts the TLCLKn pin when set. Bit 1: TCLKOn / TGCLKn / TPOHCLKn Invert (TCKOI). This bit inverts the TCLKOn / TGCLKn / TPOHCLKn pin when set. Bit 0: TCLKIn Invert (TCKII). This bit inverts the TCLKIn pin when set. 237 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PORTINV2 Port IO Invert Control Register 2 (0,2,4,6)4Ch Bit # Name Default 15 -- 0 14 RPDTI 0 13 RFOHEI 0 12 RPOHSI 0 11 -- 0 10 RPOHI 0 9 ROHSI 0 8 -- 0 Bit # Name Default 7 ROHI 0 6 ROHCKI 0 5 -- 0 4 RNEGI 0 3 RPOSI 0 2 RLCKI 0 1 RCKOI 0 0 -- 0 Bit 14: RPDATn Invert (RPDTI). This bit inverts the RPDATn pin when set. Bit 13: RFOHENIn / RPDENIn Invert (RFOHEI). This bit inverts the RFOHENIn / RPDENIn pin when set. Bit 12: RPOHSOFn / RSOFOn / RDENn / RFOHENOn Invert (RPOHSI). This bit inverts the RPOHSOFn / RSOFOn / RDENn / RFOHENOn pin when set. Bit 10: RPOHn / RSERn Invert (RPOHI). This bit inverts the RPOHn / RSERn pin when set. Bit 9: ROHSOFn Invert (ROHSI). This bit inverts the ROHSOFn pin when set. Bit 7: ROHn Invert (ROHI). This bit inverts the ROHn pin when set. Bit 6: ROHCLKn Invert (ROHCKI). This bit inverts the ROHCLKn pin when set. Bit 4: RNEGn / RLCVn / ROHMIn Invert (RNEGI). This bit inverts the RNEGn / RLCVn / ROHMIn when set. Bit 3: RPOSn / RDATn Invert (RPOSI). This bit inverts the RPOSn / RDATn pin when set. Bit 2: RLCLKn Invert (RLCKI). This bit inverts the RLCLKn pin when set. Bit 1: RCLKOn / RGCLKn / RPOHCLKn Invert (RCKOI). This bit inverts the RCLKOn / RGCLKn / RPOHCLKn pin when set. 238 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PORT.ISR Port Interrupt Status Register (0,2,4,6)50h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- PSR 9 8 LCSR Bit # Name 7 TTSR 6 FSR 5 HSR 4 BSR 3 SFSR 2 CPSR 1 PPSR 0 FMSR Bit 9: Port Status Register Interrupt Status (PSR) This bit is set when any of the latched status register bits, that are enabled for interrupt, in the PORT.SRL register are set. The interrupt pin will be driven when this bit is set and the corresponding GL.ISRIE.PISRIE[4:1] is set. Bit 8: Line Code Status Register Interrupt Status (LCSR) This bit is set when any of the latched status register bits, that are enabled for interrupt, in the B3ZS/HDB3 Line Encoder/Decoder block are set. The interrupt pin will be driven when this bit is set and the corresponding GL.ISRIE.PISRIE[4:1] is set. Bit 7: Trail Trace Status Register Interrupt Status (TTSR) This bit is set when any of the latched status register bits, that are enabled for interrupt, in the trail trace block are set. The interrupt pin will be driven when this bit is set and the corresponding GL.ISRIE.PISRIE[4:1] is set. Bit 6: FEAC Status Register Interrupt Status (FSR) This bit is set when any of the latched status register bits, that are enabled for interrupt, in the FEAC block are set. The interrupt pin will be driven when this bit is set and the corresponding GL.ISRIE.PISRIE[4:1] is set. Bit 5: HDLC Status Register Interrupt Status (HSR) This bit is set when any of the latched status register bits, that are enabled for interrupt, in the HDLC block are set. The interrupt pin will be driven when this bit is set and the corresponding GL.ISRIE.PISRIE[4:1] is set. Bit 4: BERT Status Register Interrupt Status (BSR) This bit is set when any of the latched status register bits, that are enabled for interrupt, in the BERT block are set. The interrupt pin will be driven when this bit is set and the corresponding GL.ISRIE.PISRIE[4:1] is set. Bit 3: System FIFO Status Register Interrupt Status (SFSR) This bit is set when any of the latched status register bits, that are enabled for interrupt, in either the transmit or receive FIFO block are set. The interrupt pin will be driven when this bit is set and the corresponding GL.ISRIE.PISRIE[4:1] is set. Bit 2: Cell/Packet Status Register Interrupt Status (CPSR) This bit is set when any of the latched status register bits, that are enabled for interrupt, in the active transmit or receive cell processor or packet processor block are set. The interrupt pin will be driven when this bit is set and the corresponding GL.ISRIE.PISRIE[4:1] is set. Bit 1: PLCP Status Register Interrupt Status (PPSR) This bit is set when any of the latched status register bits, that are enabled for interrupt, in the active PLCP block are set. The interrupt pin will be driven when this bit is set and the corresponding GL.ISRIE.PISRIE[4:1] is set. Bit 0: Framer Status Register Interrupt Status (FMSR) This bit is set when any of the latched status register bits, that are enabled for interrupt, in the active DS3 or E3 framer block are set. The interrupt pin will be driven when this bit is set and the corresponding GL.ISRIE.PISRIE[4:1] is set. 239 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PORT.SR Port Status Register (0,2,4,6)52h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 -- 6 -- 5 -- 4 -- 3 -- 2 TDM 1 RLOL 0 PMS Bit 2: Transmit Driver Monitor Status (TDM) This bits indicates the status of the transmit monitor circuit in the transmit LIU. 0 = Transmit output not over loaded 1 = Transmit signal is overloaded Bit 1: Receive Loss Of Lock Status (RLOL) This bits indicates the status of the receive LIU clock recovery PLL circuit. 0 = Locked to the incoming signal 1 = Not locked to the incoming signal Bit 0: Performance Monitoring Update Status (PMS) This bits indicates the status of all active performance monitoring register and counter update signals in this port. It is an "AND" of all update status bits and is not set until all performance registers are updated and the counters reset. In software update modes, the update request bit PORT.CR1.PMU should be held high until this status bit goes high. 0 = The associated update request signal is low 1 = The requested performance register updates are all completed Register Name: Register Description: Register Address: Bit # Name 15 -- PORT.SRL Port Status Register Latched (0,2,4,6)54h 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # 7 6 5 4 3 2 1 0 Name RLCLKA TCLKIA -- -- -- TDML RLOLL PMSL Bit 7: Receive Line Clock Activity Status Latched (RLCLKA) This bit will be set when the signal on the RLCLKn pin or the recovered clock from the LIU for this port is active. Bit 6: Transmit Input Clock Activity Status Latched (TCLKIA) This bit will be set when the signal on the TCLKIn pin for this port is active. Bit 2: Transmit Driver Monitor Status Latched (TDML) This bit will be set when the PORT.SR.TDM status bit changes from low to high. This bit will also set the PORT.ISR.PSR status bit if the PORT.SRIE.TDMIE bit is enabled. The interrupt pin will be driven when this bit is set, the PORT.SRIE.TDMIE bit is set, and the corresponding GL.ISRIE.PISRIE[4:1] bit is also set. Bit 1: Receive Loss Of Lock Status Latched (RLOLL) This bit will be set when the PORT.SR.RLOL status bit changes from low to high. This bit will also set the PORT.ISR.PSR status bit if the PORT.SRIE.RLOLIE bit is enabled. The interrupt pin will be driven when this bit is set, the PORT.SRIE.RLOLIE bit is set, and the corresponding GL.ISRIE.PISRIE[4:1] bit is also set. Bit 0: Performance Monitoring Update Status Latched (PMSL) This bit will be set when the PORT.SR.PMS status bit changes from low to high. This bit will also set the PORT.ISR.PSR status bit if the PORT.SRIE.PMUIE bit is enabled. The interrupt pin will be driven when this bit is set, the PORT.SRIE.PMUIE bit is set, and the PORT.SRIE.PMSIE bit are set. 240 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PORT.SRIE Port Status Register Interrupt Enable (0,2,4,6)56h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 -- 0 3 -- 0 2 TDMIE 0 1 RLOLIE 0 0 PMSIE 0 Bit 2: Transmit Driver Monitor Latched Status Interrupt Enable (TDMIE) The interrupt pin will be driven when this bit is enabled and the PORT.SRL.TDML bit is set and the bit in GL.ISRIE.PISRIE[4:1] that corresponds to this port is enabled. Bit 1: Receive Loss Of Lock Latched Status Interrupt Enable (RLOLIE) The interrupt pin will be driven when this bit is enabled and the PORT.SRL.RLOLL bit is set and the bit in GL.ISRIE.PISRIE[4:1] that corresponds to this port is enabled. Bit 0: Performance Monitoring Update Latched Status Interrupt Enable (PMSIE) The interrupt pin will be driven when this bit is enabled and the PORT.SRL.PMSL bit is set and the bit in GL.ISRIE.PISRIE[4:1] that corresponds to this port is enabled. 241 DS3181/DS3182/DS3183/DS3184 12.5 BERT 12.5.1 BERT Register Map The BERT uses 12 registers. Note that the BERT registers are cleared when GL.CR1.RSTDP or PORT.CR1.RSTDP or PORT.CR1.PD is set. Table 12-24. BERT Register Map ADDRESS (0,2,4,6)60h (0,2,4,6)62h (0,2,4,6)64h (0,2,4,6)66h (0,2,4,6)68h (0,2,4,6)6Ah (0,2,4,6)6Ch (0,2,4,6)6Eh (0,2,4,6)70h (0,2,4,6)72h (0,2,4,6)74h (0,2,4,6)76h (0,2,4,6)78h (0,2,4,6)7Ah (0,2,4,6)7Ch (0,2,4,6)7Eh REGISTER BERT.CR BERT.PCR BERT.SPR1 BERT.SPR2 BERT.TEICR -- BERT.SR BERT.SRL BERT.SRIE -- BERT.RBECR1 BERT.RBECR2 BERT.RBCR1 BERT.RBCR2 -- -- REGISTER DESCRIPTION BERT Control Register BERT Pattern Configuration Register BERT Seed/Pattern Register 1 BERT Seed/Pattern Register 2 BERT Transmit Error Insertion Control Register Unused BERT Status Register BERT Status Register Latched BERT Status Register Interrupt Enable Unused BERT Receive Bit Error Count Register 1 BERT Receive Bit Error Count Register 2 BERT Receive Bit Count Register 1 BERT Receive Bit Count Register 2 Unused Unused 12.5.2 BERT Register Bit Descriptions Register Name: Register Description: Register Address: BERT.CR BERT Control Register (0,2,4,6)60h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 PMUM 0 6 LPMU 0 5 RNPL 0 4 RPIC 0 3 MPR 0 2 APRD 0 1 TNPL 0 0 TPIC 0 Bit 7: Performance Monitoring Update Mode (PMUM) - When 0, a performance monitoring update is initiated by the LPMU register bit. When 1, a performance monitoring update is initiated by the global or port PMU register bit. Note: If the LPMU bit or the global or port PMU bit is one, changing the state of this bit may cause a performance monitoring update to occur. Bit 6: Local Performance Monitoring Update (LPMU) - This bit causes a performance monitoring update to be initiated if local performance monitoring update is enabled (PMUM = 0). A 0 to 1 transition causes the performance monitoring registers to be updated with the latest data, and the counters reset (0 or 1). For a second performance monitoring update to be initiated, this bit must be set to 0, and back to 1. If LPMU goes low before the PMS bit goes high; an update might not be performed. This bit has no affect when PMUM=1. 242 DS3181/DS3182/DS3183/DS3184 Bit 5: Receive New Pattern Load (RNPL) - A zero to one transition of this bit will cause the programmed test pattern (QRSS, PTS, PLF[4:0}, PTF[4:0], and BSP[31:0]) to be loaded in to the receive pattern generator. This bit must be changed to zero and back to one for another pattern to be loaded. Loading a new pattern will forces the receive pattern generator out of the "Sync" state which causes a re-synchronization to be initiated. Note: QRSS, PTS, PLF[4:0}, PTF[4:0], and BSP[31:0] must not change from the time this bit transitions from 0 to 1 until four receive clock cycles after this bit transitions from 0 to 1. Register bit PORT.CR1.BENA must be set and the receive clock running in order for the pattern load to take affect. Bit 4: Receive Pattern Inversion Control (RPIC) - When 0, the receive incoming data stream is not altered. When 1, the receive incoming data stream is inverted. Bit 3: Manual Pattern Re-synchronization (MPR) - A zero to one transition of this bit will cause the receive pattern generator to re-synchronize to the incoming pattern. This bit must be changed to zero and back to one for another re-synchronization to be initiated. Note: A manual re-synchronization forces the receive pattern generator out of the "Sync" state. Bit 2: Automatic Pattern Resynchronization Disable (APRD) - When 0, the receive pattern generator will automatically re-synchronize to the incoming pattern if six or more times during the current 64-bit window the incoming data stream bit and the receive pattern generator output bit did not match. When 1, the receive pattern generator will not automatically re-synchronize to the incoming pattern. Bit 1: Transmit New Pattern Load (TNPL) - A zero to one transition of this bit will cause the programmed test pattern (QRSS, PTS, PLF[4:0}, PTF[4:0], and BSP[31:0]) to be loaded in to the transmit pattern generator. This bit must be changed to zero and back to one for another pattern to be loaded. Note: QRSS, PTS, PLF[4:0}, PTF[4:0], and BSP[31:0] must not change from the time this bit transitions from 0 to 1 until four transmit clock cycles after this bit transitions from 0 to 1. Register bit PORT.CR1.BENA must be set and the transmit clock running in order for the pattern load to take affect. Bit 0: Transmit Pattern Inversion Control (TPIC) - When 0, the transmit outgoing data stream is not altered. When 1, the transmit outgoing data stream is inverted. 243 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: BERT.PCR BERT Pattern Configuration Register (0,2,4,6)62h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 PTF4 0 11 PTF3 0 10 PTF2 0 9 PTF1 0 8 PTF0 0 Bit # Name Default 7 -- 0 6 QRSS 0 5 PTS 0 4 PLF4 0 3 PLF3 0 2 PLF2 0 1 PLF1 0 0 PLF0 0 Bits 12 to 8: Pattern Tap Feedback (PTF[4:0]) - These five bits control the PRBS "tap" feedback of the pattern generator. The "tap" feedback will be from bit y of the pattern generator (y = PTF[4:0] +1). These bits are ignored when programmed for a repetitive pattern. For a PRBS signal, the feedback is an XOR of bit n and bit y. Bit 6: QRSS Enable (QRSS) - When 0, the pattern generator configuration is controlled by PTS, PLF[4:0], and PTF[4:0], and BSP[31:0]. When 1, the pattern generator configuration is forced to a PRBS pattern with a generating polynomial of x20 + x17 + 1. The output of the pattern generator will be forced to one if the next 14 output bits are all zero. Bit 5: Pattern Type Select (PTS) - When 0, the pattern is a PRBS pattern. When 1, the pattern is a repetitive pattern. Bits 4 to 0: Pattern Length Feedback (PLF[4:0]) - These five bits control the "length" feedback of the pattern generator. The "length" feedback will be from bit n of the pattern generator (n = PLF[4:0] +1). For a PRBS signal, the feedback is an XOR of bit n and bit y. For a repetitive pattern the feedback is bit n. Register Name: Register Description: Register Address: BERT.SPR1 BERT Seed/Pattern Register 1 (0,2,4,6)64h Bit # Name Default 15 BSP15 0 14 BSP14 0 13 BSP13 0 12 BSP12 0 11 BSP11 0 10 BSP10 0 9 BSP9 0 8 BSP8 0 Bit # Name Default 7 BSP7 0 6 BSP6 0 5 BSP5 0 4 BSP4 0 3 BSP3 0 2 BSP2 0 1 BSP1 0 0 BSP0 0 Bits 15 to 0: BERT Seed/Pattern (BSP[15:0]) - Lower 16 bits of 32 bits. Register description follows next register. 244 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: BERT.SPR2 BERT Seed/Pattern Register 2 (0,2,4,6)66h Bit # Name Default 15 BSP31 0 14 BSP30 0 13 BSP29 0 12 BSP28 0 11 BSP27 0 10 BSP26 0 9 BSP25 0 8 BSP24 0 Bit # Name Default 7 BSP23 0 6 BSP22 0 5 BSP21 0 4 BSP20 0 3 BSP19 0 2 BSP18 0 1 BSP17 0 0 BSP16 0 Bits 15 to 0: BERT Seed/Pattern (BSP[31:16]) - Upper 16 bits of 32 bits. BERT Seed/Pattern (BSP[31:0]) - These 32 bits are the programmable seed for a transmit PRBS pattern, or the programmable pattern for a transmit or receive repetitive pattern. BSP(31) will be the first bit output on the transmit side for a 32-bit repetitive pattern or 32-bit length PRBS. BSP(31) will be the first bit input on the receive side for a 32-bit repetitive pattern. 245 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: BERT.TEICR BERT Transmit Error Insertion Control Register (0,2,4,6)68h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 TEIR2 0 4 TEIR1 0 3 TEIR0 0 2 BEI 0 1 TSEI 0 0 MEIMS 0 Bits 5 to 3: Transmit Error Insertion Rate (TEIR[2:0]) - These three bits indicate the rate at which errors are inserted in the output data stream. One out of every 10n bits is inverted. TEIR[2:0] is the value n. A TEIR[2:0] value of 0 disables error insertion at a specific rate. A TEIR[2:0] value of 1 result in every 10th bit being inverted. A TEIR[2:0] value of 2 result in every 100th bit being inverted. Error insertion starts when this register is written to with a TEIR[2:0] value that is non-zero. If this register is written to during the middle of an error insertion process, the new error rate will be started after the next error is inserted. TEIR[2:0] Error Rate 000 Disabled 001 1*10-1 010 1*10-2 011 1*10-3 100 1*10-4 101 1*10-5 110 1*10-6 111 1*10-7 Bit 2: Bit Error Insertion Enable (BEI) - When 0, single bit error insertion is disabled. When 1, single bit error insertion is enabled. Bit 1: Transmit Single Error Insert (TSEI) - This bit causes a bit error to be inserted in the transmit data stream if manual error insertion is disabled (MEIMS = 0) and single bit error insertion is enabled. A 0 to 1 transition causes a single bit error to be inserted. For a second bit error to be inserted, this bit must be set to 0, and back to 1. Note: If MEIMS is low, and this bit transitions more than once between error insertion opportunities, only one error will be inserted. Bit 0: Manual Error Insert Mode Select (MEIMS) - When 0, error insertion is initiated by the TSEI register bit. When 1, error insertion is initiated by the transmit manual error insertion signal (TMEI). Note: If TMEI or TSEI is one, changing the state of this bit may cause a bit error to be inserted. 246 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: Bit # Name 15 -- BERT.SR BERT Status Register (0,2,4,6)6Ch 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # 7 6 5 4 3 2 1 0 Name -- -- -- -- PMS -- BEC OOS Bit 3: Performance Monitoring Update Status (PMS) - This bit indicates the status of the receive performance monitoring register (counters) update. This bit will transition from low to high when the update is completed. PMS will be forced low when the LPMU bit (PMUM = 0) or the global or port PMU bit (PMUM=1) goes low. Bit 1: Bit Error Count (BEC) - When 0, the bit error count is zero. When 1, the bit error count is one or more. This bit is cleared when the user updates the BERT counters via the PMU bit (BERT.CR). Bit 0: Out Of Synchronization (OOS) - When 0, the receive pattern generator is synchronized to the incoming pattern. When 1, the receive pattern generator is not synchronized to the incoming pattern. Register Name: Register Description: Register Address: BERT.SRL BERT Status Register Latched (0,2,4,6)6Eh Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 -- 6 -- 5 -- 4 -- 3 PMSL 2 BEL 1 BECL 0 OOSL Bit 3: Performance Monitoring Update Status Latched (PMSL) - This bit is set when the PMS bit transitions from 0 to 1. Bit 2: Bit Error Latched (BEL) - This bit is set when a bit error is detected. Bit 1: Bit Error Count Latched (BECL) - This bit is set when the BEC bit transitions from 0 to 1. Bit 0: Out Of Synchronization Latched (OOSL) - This bit is set when the OOS bit changes state. 247 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: Bit # Name Default 15 -- 0 BERT.SRIE BERT Status Register Interrupt Enable (0,2,4,6)70h 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # 7 6 5 4 3 2 1 0 Name -- -- -- -- PMSIE BEIE BECIE OOSIE Default 0 0 0 0 0 0 0 0 Bit 3: Performance Monitoring Update Status Interrupt Enable (PMSIE) - This bit enables an interrupt if the PMSL bit is set. 0 = interrupt disabled 1 = interrupt enabled Bit 2: Bit Error Interrupt Enable (BEIE) - This bit enables an interrupt if the BEL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 1: Bit Error Count Interrupt Enable (BECIE) - This bit enables an interrupt if the BECL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 0: Out Of Synchronization Interrupt Enable (OOSIE) - This bit enables an interrupt if the OOSL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled 248 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: BERT.RBECR1 BERT Receive Bit Error Count Register 1 (0,2,4,6)74h Bit # Name Default 15 BEC15 0 14 BEC14 0 13 BEC13 0 12 BEC12 0 11 BEC11 0 10 BEC10 0 9 BEC9 0 8 BEC8 0 Bit # Name Default 7 BEC7 0 6 BEC6 0 5 BEC5 0 4 BEC4 0 3 BEC3 0 2 BEC2 0 1 BEC1 0 0 BEC0 0 Bits 15 to 0: Bit Error Count (BEC[15:0]) - Lower 16 bits of 24 bits. Register description follows next register. Register Name: Register Description: Register Address: BERT.RBECR2 BERT Receive Bit Error Count Register 2 (0,2,4,6)76h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 BEC23 0 6 BEC22 0 5 BEC21 0 4 BEC20 0 3 BEC19 0 2 BEC18 0 1 BEC17 0 0 BEC16 0 Bits 7 to 0: Bit Error Count (BEC[23:16]) - Upper 8-bits of Register. Bit Error Count (BEC[23:0]) - These 24 bits indicate the number of bit errors detected in the incoming data stream. This count stops incrementing when it reaches a count of FF FFFFh. This bit error counter will not increment when an OOS condition exists. This register is updated via the PMU signal (see Section 10.4.5). 249 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: BERT.RBCR1 BERT Receive Bit Count Register 1 (0,2,4,6)78h Bit # Name Default 15 BC15 0 14 BC14 0 13 BC13 0 12 BC12 0 11 BC11 0 10 BC10 0 9 BC9 0 8 BC8 0 Bit # Name Default 7 BC7 0 6 BC6 0 5 BC5 0 4 BC4 0 3 BC3 0 2 BC2 0 1 BC1 0 0 BC0 0 Bits 15 to 0: Bit Count (BC[15:0]) - Lower 16 bits of 32 bits. Register description follows next register. Register Name: Register Description: Register Address: BERT.RBCR2 BERT Receive Bit Count Register 2 (0,2,4,6)7Ah Bit # Name Default 15 BC31 0 14 BC30 0 13 BC29 0 12 BC28 0 11 BC27 0 10 BC26 0 9 BC25 0 8 BC24 0 Bit # Name Default 7 BC23 0 6 BC22 0 5 BC21 0 4 BC20 0 3 BC19 0 2 BC18 0 1 BC17 0 0 BC16 0 Bits 15 to 0: Bit Count (BC[31:16]) - Upper 16 bits of 32 bits. Bit Count (BC[31:0]) - These 32 bits indicate the number of bits in the incoming data stream. This count stops incrementing when it reaches a count of FFFF FFFFh. This bit counter will not increment when an OOS condition exists. This register is updated via the PMU signal (see Section 10.4.5). 250 DS3181/DS3182/DS3183/DS3184 12.6 B3ZS/HDB3 Line Encoder/Decoder 12.6.1 Transmit Side Line Encoder/Decoder Register Map The transmit side uses one register. Table 12-25. Transmit Side B3ZS/HDB3 Line Encoder/Decoder Register Map ADDRESS (0,2,4,6)8Ch (0,2,4,6)8Eh REGISTER LINE.TCR -- REGISTER DESCRIPTION Line Transmit Control Register Unused 12.6.1.1 Register Bit Descriptions Register Name: Register Description: Register Address: LINE.TCR Line Transmit Control Register (0,2,4,6)8Ch Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 TZSD 0 3 EXZI 0 2 BPVI 0 1 TSEI 0 0 MEIMS 0 Bit 4: Transmit Zero Suppression Encoding Disable (TZSD) - When 0, the B3ZS/HDB3 Encoder performs zero suppression (B3ZS or HDB3) and AMI encoding. When 1, zero suppression (B3ZS or HDB3) encoding is disabled, and only AMI encoding is performed. Bit 3: Excessive Zero Insert Enable (EXZI) - When 0, excessive zero (EXZ) event insertion is disabled. When 1, EXZ event insertion is enabled. Bit 2: Bipolar Violation Insert Enable (BPVI) - When 0, bipolar violation (BPV) insertion is disabled. When 1, BPV insertion is enabled. Bit 1: Transmit Single Error Insert (TSEI) - This bit causes an error of the enabled type(s) to be inserted in the transmit data stream if manual error insertion is disabled (MEIMS = 0). A 0 to 1 transition causes a single error to be inserted. For a second error to be inserted, this bit must be set to 0, and back to 1. Note: If MEIMS is low, and this bit transitions more than once between error insertion opportunities, only one error will be inserted. Bit 0: Manual Error Insert Mode Select (MEIMS) - When 0, error insertion is initiated by the TSEI register bit. When 1, error insertion is initiated by the transmit manual error insertion signal (TMEI). Note: If TMEI or TSEI is one, changing the state of this bit may cause an error to be inserted. 251 DS3181/DS3182/DS3183/DS3184 12.6.2 Receive Side Line Encoder/Decoder Register Map The receive side uses six registers. Table 12-26. Receive Side B3ZS/HDB3 Line Encoder/Decoder Register Map ADDRESS (0,2,4,6)90h (0,2,4,6)92h (0,2,4,6)94h (0,2,4,6)96h (0,2,4,6)98h (0,2,4,6)9Ah (0,2,4,6)9Ch (0,2,4,6)9Eh REGISTER LINE.RCR -- LINE.RSR LINE.RSRL LINE.RSRIE -- LINE.RBPVCR LINE.REXZCR REGISTER DESCRIPTION Line Receive Control Register Unused Line Receive Status Register Line Receive Status Register Latched Line Receive Status Register Interrupt Enable Unused Line Receive Bipolar Violation Count Register Line Receive Excessive Zero Count Register 12.6.2.1 Register Bit Descriptions Register Name: Register Description: Register Address: LINE.RCR Line Receive Control Register (0.2.4.6)90h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 -- 0 3 E3CVE 0 2 REZSF 0 1 RDZSF 0 0 RZSD 0 Bit 3: E3 Code Violation Enable (E3CVE) - When 0, the bipolar violation count will be a count of bipolar violations. When 1, the bipolar violation count will be a count of E3 line coding violations. Note: E3 line coding violations are defined as consecutive bipolar violations of the same polarity in ITU O.161. This bit is ignored in B3ZS mode. Bit 2: Receive BPV Error Detection Zero Suppression Code Format (REZSF) - When 0, BPV error detection detects a B3ZS signature if a zero is followed by a bipolar violation (BPV), and an HDB3 signature if two zeros are followed by a BPV. When 1, BPV error detection detects a B3ZS signature if a zero is followed by a BPV that has the opposite polarity of the BPV in the previous B3ZS signature, and an HDB3 signature if two zeros are followed by a BPV that has the opposite polarity of the BPV in the previous HDB3 signature. Note: Immediately after a reset, this bit is ignored. The first B3ZS signature is defined as a zero followed by a BPV, and the first HDB3 signature is defined as two zeros followed by a BPV. All subsequent B3ZS/HDB3 signatures will be determined by the setting of this bit. Note: The default setting (REZSF = 0) conforms to ITU O.162. The default setting may falsely decode actual BPVs that are not codewords. It is recommended that REZSF be set to one for most applications. This setting is more robust to accurately detect codewords. Bit 1: Receive Zero Suppression Decoding Zero Suppression Code Format (RDZSF) - When 0, zero suppression decoding detects a B3ZS signature if a zero is followed by a bipolar violation (BPV), and an HDB3 signature if two zeros are followed by a BPV. When 1, zero suppression decoding detects a B3ZS signature if a zero is followed by a BPV that has the opposite polarity of the BPV in the previous B3ZS signature, and an HDB3 signature if two zeros are followed by a BPV that has the opposite polarity of the BPV in the previous HDB3 signature. Note: Immediately after a reset (DRST or RST low), this bit is ignored. The first B3ZS signature is defined as a zero followed by a BPV, and the first HDB3 signature is defined as two zeros followed by a BPV. All subsequent B3ZS/HDB3 signatures will be determined by the setting of this bit. Bit 0: Receive Zero Suppression Decoding Disable (RZSD) - When 0, the B3ZS/HDB3 Decoder performs zero suppression (B3ZS or HDB3) and AMI decoding. When 1, zero suppression (B3ZS or HDB3) decoding is disabled, and only AMI decoding is performed. 252 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: LINE.RSR Line Receive Status Register (0.2.4.6)94h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 -- 6 -- 5 -- 4 -- 3 EXZC 2 -- 1 BPVC 0 LOS Bit 3: Excessive Zero Count (EXZC) - When 0, the excessive zero count is zero. When 1, the excessive zero count is one or more. Bit 1: Bipolar Violation Count (BPVC) - When 0, the bipolar violation count is zero. When 1, the bipolar violation count is one or more. Bit 0: Loss Of Signal (LOS) - When 0, the receive line is not in a loss of signal (LOS) condition. When 1, the receive line is in an LOS condition. See Section 10.14.5. Note: When zero suppression (B3ZS or HDB3) decoding is disabled, the LOS condition is cleared, and cannot be detected. Register Name: Register Description: Register Address: LINE.RSRL Line Receive Status Register Latched (0.2.4.6)96h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 -- 6 -- 5 ZSCDL 4 EXZL 3 EXZCL 2 BPVL 1 BPVCL 0 LOSL Bit 5: Zero Suppression Code Detect Latched (ZSCDL) - This bit is set when a B3ZS or HDB3 signature is detected. Bit 4: Excessive Zero Latched (EXZL) - This bit is set when an excessive zero event is detected on the incoming bipolar data stream. Bit 3: Excessive Zero Count Latched (EXZCL) - This bit is set when the LINE.RSR.EXZC bit transitions from zero to one. Bit 2: Bipolar Violation Latched (BPVL) - This bit is set when a bipolar violation (or E3 LCV if enabled) is detected on the incoming bipolar data stream. Bit 1: Bipolar Violation Count Latched (BPVCL) - This bit is set when the LINE.RSR.BPVC bit transitions from zero to one. Bit 0: Loss of Signal Change Latched (LOSL) - This bit is set when the LINE.RSR.LOS bit changes state. 253 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: LINE.RSRIE Line Receive Status Register Interrupt Enable (0.2.4.6)98h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 ZSCDIE 0 4 EXZIE 0 3 EXZCIE 0 2 BPVIE 0 1 BPVCIE 0 0 LOSIE 0 Bit 5: Zero Suppression Code Detect Interrupt Enable (ZSCDIE) - This bit enables an interrupt if the LINE.RSRL.ZSCDL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 4: Excessive Zero Interrupt Enable (EXZIE) - This bit enables an interrupt if the LINE.RSRL.EXZL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 3: Excessive Zero Count Interrupt Enable (EXZCIE) - This bit enables an interrupt if the LINE.RSRL.EXZCL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 2: Bipolar Violation Interrupt Enable (BPVIE) - This bit enables an interrupt if the LINE.RSRL.BPVL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 1: Bipolar Violation Count Interrupt Enable (BPVCIE) - This bit enables an interrupt if the LINE.RSRL.BPVCL bit and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. is set. 0 = interrupt disabled 1 = interrupt enabled Bit 0: Loss Of Signal Interrupt Enable (LOSIE) - This bit enables an interrupt if the LINE.RSRL.LOSL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled 254 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: LINE.RBPVCR Line Receive Bipolar Violation Count Register (0.2.4.6)9Ch Bit # Name Default 15 BPV15 0 14 BPV14 0 13 BPV13 0 12 BPV12 0 11 BPV11 0 10 BPV10 0 9 BPV9 0 8 BPV8 0 Bit # Name Default 7 BPV7 0 6 BPV6 0 5 BPV5 0 4 BPV4 0 3 BPV3 0 2 BPV2 0 1 BPV1 0 0 BPV0 0 Bits 15 to 0: Bipolar Violation Count (BPV[15:0]) - These 16 bits indicate the number of bipolar violations detected on the incoming bipolar data stream. This register is updated via the PMU signal (see Section 10.4.5) Register Name: Register Description: Register Address: LINE.REXZCR Line Receive Excessive Zero Count Register (0.2.4.6)9Eh Bit # Name Default 15 EXZ15 0 14 EXZ14 0 13 EXZ13 0 12 EXZ12 0 11 EXZ11 0 10 EXZ10 0 9 EXZ9 0 8 EXZ8 0 Bit # Name Default 7 EXZ7 0 6 EXZ6 0 5 EXZ5 0 4 EXZ4 0 3 EXZ3 0 2 EXZ2 0 1 EXZ1 0 0 EXZ0 0 Bits 15 to 0: Excessive Zero Count (EXZ[15:0]) - These 16 bits indicate the number of excessive zero conditions detected on the incoming bipolar data stream. This register is updated via the PMU signal (see Section 10.4.5) 255 DS3181/DS3182/DS3183/DS3184 12.7 HDLC 12.7.1 HDLC Transmit Side Register Map The transmit side uses five registers. Table 12-27. Transmit Side HDLC Register Map ADDRESS REGISTER (0,2,4,6)A0h (0,2,4,6)A2h (0,2,4,6)A4h (0,2,4,6)A6h (0,2,4,6)A8h (0,2,4,6)AAh (0,2,4,6)ACh (0,2,4,6)AEh HDLC.TCR HDLC.TFDR HDLC.TSR HDLC.TSRL HDLC.TSRIE -- -- -- REGISTER DESCRIPTION HDLC Transmit Control Register HDLC Transmit FIFO Data Register HDLC Transmit Status Register HDLC Transmit Status Register Latched HDLC Transmit Status Register Interrupt Enable Unused Unused Unused 12.7.1.1 Register Bit Descriptions Register Name: Register Description: Register Address: HDLC.TCR HDLC Transmit Control Register (0,2,4,6)A0h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 TDAL4 0 11 TDAL3 1 10 TDAL2 0 9 TDAL1 0 8 TDAL0 0 Bit # Name Default 7 -- 0 6 TPSD 0 5 TFEI 0 4 TIFV 0 3 TBRE 0 2 TDIE 0 1 TFPD 0 0 TFRST 0 Bits 12 to 8: Transmit HDLC Data Storage Available Level (TDAL[4:0]) - These five bits indicate the minimum number of bytes ([TDAL*8]+1) that must be available for storage (do not contain data) in the Transmit FIFO for HDLC data storage to be available. For example, a value of 21 (15h) results in HDLC data storage being available (THDA = 1) when the Transmit FIFO has 169 (A9h) bytes or more available for storage, and HDLC data storage not being available (THDA = 0) when the Transmit FIFO has 168 (A8h) bytes or less available for storage. Default value (after reset) is 128 bytes minimum available. Bit 6: Transmit Packet Start Disable (TPSD) - When 0, the Transmit Packet Processor will continue sending packets after the current packet end. When 1, the Transmit Packet Processor will stop sending packets after the current packet end. Bit 5: Transmit FCS Error Insertion (TFEI) - When 0, the calculated FCS (inverted CRC-16) is appended to the packet. When 1, the inverse of the calculated FCS (non-inverted CRC-16) is appended to the packet causing a FCS error. This bit is ignored if transmit FCS processing is disabled (TFPD = 1). Bit 4: Transmit Inter-frame Fill Value (TIFV) - When 0, inter-frame fill is done with the flag sequence (7Eh). When 1, inter-frame fill is done with all `1's. Bit 3: Transmit Bit Reordering Enable (TBRE) - When 0, bit reordering is disabled (The first bit transmitted is the LSB of the Transmit FIFO Data byte TFD[0]). When 1, bit reordering is enabled (The first bit transmitted is the MSB of the Transmit FIFO Data byte TFD[7]). Bit 2: Transmit Data Inversion Enable (TDIE) - When 0, the outgoing data is directly output from packet processing. When 1, the outgoing data is inverted before being output from packet processing. 256 DS3181/DS3182/DS3183/DS3184 Bit 1: Transmit FCS Processing Disable (TFPD) - This bit controls whether or not a FCS is calculated and appended to the end of each packet. When 0, the calculated FCS bytes are appended to the end of the packet. When 1, the packet is transmitted without a FCS. Bit 0: Transmit FIFO Reset (TFRST) - When 0, the Transmit FIFO will resume normal operations, however, data is discarded until a start of packet is received after RAM power-up is completed. When 1, the Transmit FIFO is emptied, any transfer in progress is halted, the FIFO RAM is powered down, and all incoming data is discarded (all TFDR register writes are ignored). Register Name: Register Description: Register Address: HDLC.TFDR HDLC Transmit FIFO Data Register (0,2,4,6)A2h Bit # Name Default 15 TFD7 0 14 TFD6 0 13 TFD5 0 12 TFD4 0 11 TFD3 0 10 TFD2 0 9 TFD1 0 8 TFD0 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 -- 0 3 -- 0 2 -- 0 1 -- 0 0 TDPE 0 Note: The FIFO data and status are loaded into the Transmit FIFO when the Transmit FIFO Data (TFD[7:0]) is written (upper byte write). When read, the value of these bits is always zero. Bits 15 to 8: Transmit FIFO Data (TFD[7:0]) - These eight bits are the packet data to be stored in the Transmit FIFO. TFD[7] is the MSB, and TFD[0] is the LSB. If bit reordering is disabled, TFD[0] is the first bit transmitted, and TFD[7] is the last bit transmitted. If bit reordering is enabled, TFD[7] is the first bit transmitted, and TFD[0] is the last bit transmitted. Bit 0: Transmit FIFO Data Packet End (TDPE) - When 0, the Transmit FIFO data is not a packet end. When 1, the Transmit FIFO data is a packet end. Register Name: Register Description: Register Address: HDLC.TSR HDLC Transmit Status Register (0,2,4,6)A4h Bit # Name 15 -- 14 -- 13 TFFL5 12 TFFL4 11 TFFL3 10 TFFL2 9 TFFL1 Bit # Name 7 -- 6 -- 5 -- 4 -- 3 -- 2 TFF 1 TFE 8 TFFL0 0 THDA Bits 13 to 8: Transmit FIFO Fill Level (TFFL[5:0]) - These six bits indicate the number of eight byte groups available for storage (do not contain data) in the Transmit FIFO. E.g., a value of 21 (15h) indicates the FIFO has 168 (A8h) to 175 (AFh) bytes are available for storage. Bit 2: Transmit FIFO Full (TFF) - When 0, the Transmit FIFO contains 255 or less bytes of data. When 1, the Transmit FIFO is full. Bit 1: Transmit FIFO Empty (TFE) - When 0, the Transmit FIFO contains at least one byte of data. When 1, the Transmit FIFO is empty. Bit 0: Transmit HDLC Data Storage Available (THDA) - When 0, the Transmit FIFO has less storage space available in the Transmit FIFO than the Transmit HDLC data storage available level (TDAL[4:0]). When 1, the Transmit FIFO has the same or more storage space available than the Transmit FIFO HDLC data storage available level. 257 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: HDLC.TSRL HDLC Transmit Status Register Latched (0,2,4,6)A6h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 -- 6 -- 5 TFOL 4 TFUL 3 TPEL 2 -- 1 TFEL 0 THDAL Bit 5: Transmit FIFO Overflow Latched (TFOL) - This bit is set when a Transmit FIFO overflow condition occurs. Bit 4: Transmit FIFO Underflow Latched (TFUL) - This bit is set when a Transmit FIFO underflow condition occurs. An underflow condition results in a loss of data. Bit 3: Transmit Packet End Latched (TPEL) - This bit is set when an end of packet is read from the Transmit FIFO. Bit 1: Transmit FIFO Empty Latched (TFEL) - This bit is set when the TFE bit transitions from 0 to 1. Note: This bit is also set when HDLC.TCR.TFRST is deasserted. Bit 0: Transmit HDLC Data Available Latched (THDAL) - This bit is set when the THDA bit transitions from 0 to 1. Note: This bit is also set when HDLC.TCR.TFRST is deasserted. 258 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: HDLC.TSRIE HDLC Transmit Status Register Interrupt Enable (0,2,4,6)A8h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 TFOIE 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 4 TFUIE 0 3 TPEIE 0 2 -- 0 1 TFEIE 0 0 THDAIE 0 Bit 5: Transmit FIFO Overflow Interrupt Enable (TFOIE) - This bit enables an interrupt if the TFOL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 4: Transmit FIFO Underflow Interrupt Enable (TFUIE) - This bit enables an interrupt if the TFUL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 3: Transmit Packet End Interrupt Enable (TPEIE) - This bit enables an interrupt if the TPEL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 2: Transmit FIFO Full Interrupt Enable (TFFIE) - This bit enables an interrupt if the TFFL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 1: Transmit FIFO Empty Interrupt Enable (TFEIE) - This bit enables an interrupt if the TFEL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 0: Transmit HDLC Data Available Interrupt Enable (THDAIE) - This bit enables an interrupt if the THDAL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled 259 DS3181/DS3182/DS3183/DS3184 12.7.2 HDLC Receive Side Register Map The receive side uses five registers. Table 12-28. Receive Side HDLC Register Map ADDRESS (0,2,4,6)B0h (0,2,4,6)B2h (0,2,4,6)B4h (0,2,4,6)B6h (0,2,4,6)B8h (0,2,4,6)BAh (0,2,4,6)BCh (0,2,4,6)BEh REGISTER HDLC.RCR -- HDLC.RSR HDLC.RSRL HDLC.RSRIE -- HDLC.RFDR -- REGISTER DESCRIPTION HDLC Receive Control Register Unused HDLC Receive Status Register HDLC Receive Status Register Latched HDLC Receive Status Register Interrupt Enable Unused HDLC Receive FIFO Data Register Unused 12.7.2.1 Register Bit Descriptions Register Name: Register Description: Register Address: HDLC.RCR HDLC Receive Control Register (0,2,4,6)B0h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 RDAL4 0 11 RDAL3 1 10 RDAL2 0 9 RDAL1 0 8 RDAL0 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 -- 0 3 RBRE 0 2 RDIE 0 1 RFPD 0 0 RFRST 0 Bits 12 to 8: Receive HDLC Data Available Level (RDAL[4:0]) - These five bits indicate the minimum number of eight byte groups that must be stored (contain data) in the Receive FIFO before HDLC data is considered to be available (RHDA=1). For example, a value of 21 (15h) results in HDLC data being available when the Receive FIFO contains 168 (A8h) bytes or more. Bit 3: Receive Bit Reordering Enable (RBRE) - When 0, bit reordering is disabled (The first bit received is in the LSB of the Receive FIFO Data byte RFD[0]). When 1, bit reordering is enabled (The first bit received is in the MSB of the Receive FIFO Data byte RFD[7]). Bit 2: Receive Data Inversion Enable (RDIE) - When 0, the incoming data is directly passed on for packet processing. When 1, the incoming data is inverted before being passed on for packet processing. Bit 1: Receive FCS Processing Disable (RFPD) - When 0, FCS processing is performed (the packets have a FCS appended). When 1, FCS processing is disabled (the packets do not have a FCS appended). Bit 0: Receive FIFO Reset (RFRST) - When 0, the Receive FIFO will resume normal operations, however, data is discarded until a start of packet is received after RAM power-up is completed. When 1, the Receive FIFO is emptied, any transfer in progress is halted, the FIFO RAM is powered down, the RHDA bit is forced low, and all incoming data is discarded. 260 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: HDLC.RSR HDLC Receive Status Register (0,2,4,6)B4h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 -- 6 -- 5 -- 4 -- 3 -- 2 RFF 1 RFE 0 RHDA Bit 2: Receive FIFO Full (RFF) - When 0, the Receive FIFO contains 255 or less bytes of data. When 1, the Receive FIFO is full. Bit 1: Receive FIFO Empty (RFE) - When 0, the Receive FIFO contains at least one byte of data. When 1, the Receive FIFO is empty. Bit 0: Receive HDLC Data Available (RHDA) - When 0, the Receive FIFO contains less data than the Receive HDLC data available level (RDAL[4:0]). When 1, the Receive FIFO contains the same or more data than the Receive HDLC data available level. Register Name: Register Description: Register Address: HDLC.RSRL HDLC Receive Status Register Latched (0,2,4,6)B6h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 RFOL 6 -- 5 -- 4 RPEL 3 RPSL 2 RFFL 1 -- 0 RHDAL Bit 7: Receive FIFO Overflow Latched (RFOL) - This bit is set when a Receive FIFO overflow condition occurs. An overflow condition results in a loss of data. Bit 4: Receive Packet End Latched (RPEL) - This bit is set when an end of packet is stored in the Receive FIFO. Bit 3: Receive Packet Start Latched (RPSL) - This bit is set when a start of packet is stored in the Receive FIFO. Bit 2: Receive FIFO Full Latched (RFFL) - This bit is set when the RFF bit transitions from 0 to 1. Bit 0: Receive HDLC Data Available Latched (RHDAL) - This bit is set when the RHDA bit transitions from 0 to 1. 261 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: HDLC.RSRIE HDLC Receive Status Register Interrupt Enable (0,2,4,6)B8h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 RFOIE 0 6 -- 0 5 -- 0 4 RPEIE 0 3 RPSIE 0 2 RFFIE 0 1 -- 0 0 RHDAIE 0 Bit 7: Receive FIFO Overflow Interrupt Enable (RFOIE) - This bit enables an interrupt if the RFOL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 4: Receive Packet End Interrupt Enable (RPEIE) - This bit enables an interrupt if the RPEL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 3: Receive Packet Start Interrupt Enable (RPSIE) - This bit enables an interrupt if the RPSL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 2: Receive FIFO Full Interrupt Enable (RFFIE) - This bit enables an interrupt if the RFFL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 0: Receive HDLC Data Available Interrupt Enable (RHDAIE) - This bit enables an interrupt if the RHDAL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled 262 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: HDLC.RFDR HDLC Receive FIFO Data Register (0,2,4,6)BCh Bit # Name Default 15 RFD7 X 14 RFD6 X 13 RFD5 X 12 RFD4 X 11 RFD3 X 10 RFD2 X 9 RFD1 X 8 RFD0 X Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 -- 0 3 RPS2 X 2 RPS1 X 1 RPS0 X 0 RFDV 0 Note: The FIFO data and status are updated when the Receive FIFO Data (RFD[7:0]) is read (upper byte read). When this register is read eight bits at a time, a read of the lower byte will reflect the status of the next read of the upper byte, and reading the upper byte when RFDV=0 may result in a loss of data. Bits 15 to 8: Receive FIFO Data (RFD[7:0]) - These eight bits are the packet data stored in the Receive FIFO. RFD[7] is the MSB, and RFD[0] is the LSB. If bit reordering is disabled, RFD[0] is the first bit received, and RFD[7] is the last bit received. If bit reordering is enabled, RFD[7] is the first bit received, and RFD[0] is the last bit received. Bits 3 to 1: Receive Packet Status (RPS[2:0]) - These three bits indicate the status of the received packet and packet data. 000 = packet middle 001 = packet start. 010 = reserved 011 = reserved 100 = packet end: good packet 101 = packet end: FCS errored packet. 110 = packet end: invalid packet (a non-integer number of bytes). 111 = packet end: aborted packet. Bit 0: Receive FIFO Data Valid (RFDV) - When 0, the Receive FIFO data (RFD[7:0]) is invalid (the Receive FIFO is empty). When 1, the Receive FIFO data (RFD[7:0]) is valid. 263 DS3181/DS3182/DS3183/DS3184 12.8 FEAC Controller 12.8.1 FEAC Transmit Side Register Map The transmit side uses five registers. Table 12-29. FEAC Transmit Side Register Map ADDRESS REGISTER (0,2,4,6)C0h (0,2,4,6)C2h (0,2,4,6)C4h (0,2,4,6)C6h (0,2,4,6)C8h (0,2,4,6)CAh (0,2,4,6)CCh (0,2,4,6)CEh FEAC.TCR FEAC.TFDR FEAC.TSR FEAC.TSRL FEAC.TSRIE -- -- -- REGISTER DESCRIPTION FEAC Transmit Control Register FEAC Transmit Data Register FEAC Transmit Status Register FEAC Transmit Status Register Latched FEAC Transmit Status Register Interrupt Enable Unused Unused Unused 12.8.1.1 Register Bit Descriptions Register Name: Register Description: Register Address: FEAC.TCR FEAC Transmit Control Register (0,2,4,6)C0h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 1 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 -- 0 3 -- 0 2 TFCL 0 1 TFS1 0 0 TFS0 0 Bit 2: Transmit FEAC Codeword Load (TFCL) - A 0 to 1 transition on this bit loads the transmit FEAC processor mode select bits (TFS[1:0]), and transmit FEAC codes (TFCA[5:0] and TFCB[5:0]). Note: Whenever a FEAC codeword is loaded, any current FEAC codeword transmission in progress will be immediately halted, and the new FEAC codeword transmission will be started based on the new values for TFS[1:0], TFCA[5:0], and TFCB[5:0].. Bits 1 to 0: Transmit FEAC Codeword Select (TFS[1:0]) - These two bits control the transmit FEAC processor mode. The TFCL bit loads the mode set by this bit. 00 = Idle (all ones) 01 = single code (send code TFCA ten times and send all ones) 10 = dual code (send code TFCA ten times, send code TFCB ten times, and send all ones) 11 = continuous code (send code TFCA continuously) 264 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: FEAC.TFDR FEAC Transmit Data Register (0,2,4,6)C2h Bit # Name Default 15 -- 0 14 -- 0 13 TFCB5 0 12 TFCB4 0 11 TFCB3 0 10 TFCB2 0 9 TFCB1 0 8 TFCB0 0 Bit # Name Default 7 -- 0 6 -- 0 5 TFCA5 0 4 TFCA4 0 3 TFCA3 0 2 TFCA2 0 1 TFCA1 0 0 TFCA0 0 Bits 13 to 8: Transmit FEAC Code B (TFCB[5:0]) - These six bits are the transmit FEAC code B data to be stored inserted into codeword B. TFCB[5] is the LSB (last bit transmitted) of the FEAC code (C[6]), and TFCB[0] is the MSB (first bit transmitted) of the FEAC code (C[1]). Bits 5 to 0: Transmit FEAC Code A (TFCA[5:0]) - These six bits are the transmit FEAC code A data to be stored inserted into codeword A. TFCA[5] is the LSB (last bit transmitted) of the FEAC code (C[6]), and TFCA[0] is the MSB (first bit transmitted) of the FEAC code (C[1]). Register Name: Register Description: Register Address: FEAC.TSR FEAC Transmit Status Register (0,2,4,6)C4h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 -- 6 -- 5 -- 4 -- 3 -- 2 -- 1 -- 0 TFI Bit 0: Transmit FEAC Idle (TFI) - When 0, the Transmit FEAC processor is sending a FEAC codeword. When 1, the Transmit FEAC processor is sending an Idle signal (all ones). 265 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: FEAC.TSRL FEAC Transmit Status Register Latched (0,2,4,6)C6h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 -- 6 -- 5 -- 4 -- 3 -- 2 -- 1 -- 0 TFIL Bit 0: Transmit FEAC Idle Latched (TFIL) - This bit is set when the TFI bit transitions from 0 to 1. Note: Immediately after a reset, this bit will be set to one. Register Name: Register Description: Register Address: FEAC.TSRIE FEAC Transmit Status Register Interrupt Enable (0,2,4,6)C8h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 -- 0 3 -- 0 2 -- 0 1 -- 0 0 TFIIE 0 Bit 0: Transmit FEAC Idle Interrupt Enable (TFIIE) - This bit enables an interrupt if the TFIL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled 266 DS3181/DS3182/DS3183/DS3184 12.8.2 FEAC Receive Side Register Map The receive side uses five registers. Table 12-30. FEAC Receive Side Register Map ADDRESS (0,2,4,6)D0h (0,2,4,6)D2h (0,2,4,6)D4h (0,2,4,6)D6h (0,2,4,6)D8h (0,2,4,6)DAh (0,2,4,6)DCh (0,2,4,6)DEh REGISTER FEAC.RCR -- FEAC.RSR FEAC.RSRL FEAC.RSRIE -- FEAC.RFDR -- REGISTER DESCRIPTION FEAC Receive Control Register Unused FEAC Receive Status Register FEAC Receive Status Register Latched FEAC Receive Status Register Interrupt Enable Unused FEAC Receive FIFO Data Register Unused 12.8.2.1 Register Bit Descriptions Register Name: Register Description: Register Address: FEAC.RCR FEAC Receive Control Register (0,2,4,6)D0h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 1 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 -- 0 3 -- 0 2 -- 0 1 -- 0 0 RFR 0 Bit 0: Receive FEAC Reset (RFR) -When 0, the Receive FEAC Processor and Receive FEAC FIFO will resume normal operations. When 1, the Receive FEAC controller is reset. The FEAC FIFO is emptied, any transfer in progress is halted, and all incoming data is discarded. Register Name: Register Description: Register Address: FEAC.RSR FEAC Receive Status Register (0,2,4,6)D4h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 -- 6 -- 5 -- 4 -- 3 RFFE 2 -- 1 RFCD 0 RFI Bit 3: Receive FEAC FIFO Empty (RFFE) - When 0, the Receive FIFO contains at least one code. When 1, the Receive FIFO is empty. Bit 1: Receive FEAC Codeword Detect (RFCD) - When 0, the Receive FEAC Processor is not currently receiving a FEAC codeword. When 1, the Receive FEAC Processor is currently receiving a FEAC codeword. Bit 0: Receive FEAC Idle (RFI) - When 0, the Receive FEAC processor is not receiving a FEAC Idle signal (all ones). When 1, the Receive FEAC processor is receiving a FEAC Idle signal. 267 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: FEAC.RSRL FEAC Receive Status Register Latched (0,2,4,6)D6h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 -- 6 -- 5 -- 4 -- 3 -- 2 RFFOL 1 RFCDL 0 RFIL Bit 2: Receive FEAC FIFO Overflow Latched (RFFOL) - This bit is set when a Receive FIFO overflow condition occurs. An overflow condition results in a loss of data. Bit 1: Receive FEAC Codeword Detect Latched (RFCDL) - This bit is set when the RFCD bit transitions from 0 to 1. Bit 0: Receive FEAC Idle Latched (RFIL) - This bit is set when the RFI bit transitions from 0 to 1. Note: Immediately after a reset, this bit will be set to one. Register Name: Register Description: Register Address: FEAC.RSRIE FEAC Receive Status Register Interrupt Enable (0,2,4,6)D8h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 -- 0 3 -- 0 2 RFFOIE 0 1 RFCDIE 0 0 RFIIE 0 Bit 2: Receive FEAC FIFO Overflow Interrupt Enable (RFFOIE) - This bit enables an interrupt if the RFFOL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 1: Receive FEAC Codeword Detect Interrupt Enable (RFCDIE) - This bit enables an interrupt if the RFCDL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 0: Receive FEAC Idle Interrupt Enable (RFIIE) - This bit enables an interrupt if the RFIL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled 268 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: FEAC.RFDR FEAC Receive FIFO Data Register (0,2,4,6)DCh Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 RFFI 0 6 -- 0 5 RFF5 0 4 RFF4 0 3 RFF3 0 2 RFF2 0 1 RFF1 0 0 RFF0 0 Bit 7: Receive FEAC FIFO Data Invalid (RFFI) - When 0, the Receive FIFO data (RFF[5:0]) is valid. When 1, the Receive FIFO data is invalid (Receive FIFO is empty). Bits 5 to 0: Receive FEAC FIFO Data (RFF[5:0]) - These six bits are the FEAC code data stored in the Receive FIFO. RFF[5] is the LSB (last bit received) of the FEAC code (C[6]), and RFF[0] is the MSB (first bit received) of the FEAC code (C[1]). The Receive FEAC FIFO data (RFF[5:0]) is updated when it is read (lower byte read). 269 DS3181/DS3182/DS3183/DS3184 12.9 Trail Trace 12.9.1 Trail Trace Transmit Side The transmit side uses three registers. Table 12-31. Transmit Side Trail Trace Register Map ADDRESS REGISTER (0,2,4,6)E8h (0,2,4,6)EAh (0,2,4,6)ECh (0,2,4,6)EEh TT.TCR TT.TTIAR TT.TIR -- REGISTER DESCRIPTION Trail Trace Transmit Control Register Trail Trace Transmit Identifier Address Register Trail Trace Transmit Identifier Register Unused 12.9.1.1 Register Bit Descriptions Register Name: Register Description: Register Address: TT.TCR Trail Trace Transmit Control Register (0,2,4,6)E8h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 Reserved 0 3 TMAD 0 2 TIDLE 0 1 TDIE 0 0 TBRE 0 Bit 3: Transmit Multiframe Alignment Insertion Disable (TMAD) - When 0, multiframe alignment signal (MAS) insertion is enabled, and the first bit transmitted of each trail trace byte is overwritten with an MAS bit. When 1, MAS insertion is disabled, and the trail trace bytes from the Transmit Data Storage are output without being modified. Bit 2: Transmit Trail Trace Identifier Idle (TIDLE) - When 0, the programmed transmit trail trace identifier will be transmitted. When 1, all zeros will be transmitted. Bit 1: Transmit Data Inversion Enable (TDIE) - When 0, the outgoing data from trail trace processing is output directly. When 1, the outgoing data from trail trace processing is inverted before being output. Bit 0: Transmit Bit Reordering Enable (TBRE) - When 0, bit reordering is disabled (The first bit transmitted is the MSB TT.TIR.TTD[7] of the byte). When 1, bit reordering is enabled (The first bit transmitted is the LSB TT.TIR.TTD[0] of the byte). 270 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: TT.TTIAR Trail Trace Transmit Identifier Address Register (0,2,4,6)EAh Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 Reserved 0 4 Reserved 0 3 TTIA3 0 2 TTIA2 0 1 TTIA1 0 0 TTIA0 0 Bits 3 to 0: Transmit Trail Trace Identifier Address (TTIA[3:0]) - These four bits indicate the transmit trail trace identifier byte to be read/written by the next memory access. Address 0h indicates the first byte of the transmit trail trace identifier. Note: The value of these bits increments with each transmit trail trace identifier memory access (when these bits are Fh, a memory access will return them to 0h). Register Name: Register Description: Register Address: TT.TIR Trail Trace Transmit Identifier Register (0,2,4,6)ECh Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 TTD7 0 6 TTD6 0 5 TTD5 0 4 TTD4 0 3 TTD3 0 2 TTD2 0 1 TTD1 0 0 TTD0 0 Bits 7 to 0: Transmit Trail Trace Identifier Data (TTD[7:0]) - These eight bits are the transmit trail trace identifier data. The transmit trail trace identifier address will be incremented whenever these bits are read or written (when address location Fh is read or written, the address will return to 0h). 271 DS3181/DS3182/DS3183/DS3184 12.9.2 Trail Trace Receive Side Register Map The receive side uses seven registers. Table 12-32. Trail Trace Receive Side Register Map ADDRESS REGISTER (0,2,4,6)F0h (0,2,4,6)F2h (0,2,4,6)F4h (0,2,4,6)F6h (0,2,4,6)F8h (0,2,4,6)FAh (0,2,4,6)FCh (0,2,4,6)FEh TT.RCR TT.RTIAR TT.RSR TT.RSRL TT.RSRIE -- TT.RIR TT.EIR REGISTER DESCRIPTION Trail Trace Receive Control Register Trail Trace Receive Identifier Address Register Trail Trace Receive Status Register Trail Trace Receive Status Register Latched Trail Trace Receive Status Register Interrupt Enable Unused Trail Trace Receive Identifier Register Trail Trace Expected Identifier Register 12.9.2.1 Register Bit Descriptions Register Name: Register Description: Register Address: TT.RCR Trail Trace Receive Control Register (0,2,4,6)F0h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 Reserved 0 4 Reserved 0 3 RMAD 0 2 RETCE 0 1 RDIE 0 0 RBRE 0 Bit 3: Receive Multiframe Alignment Disable (RMAD) - When 0, multiframe alignment is performed. When 1, multiframe alignment is disabled and the trail trace bytes are stored starting with a random byte. Bit 2: Receive Expected Trail Trace Comparison Enable (RETCE) - When 0, expected trail trace comparison is disabled. When 1, expected trail trace comparison is performed. Note: When the RMAD bit is one, expected trail trace comparison is disabled regardless of the setting of this bit. Bit 1: Receive Data Inversion Enable (RDIE) - When 0, the incoming data is directly passed on for trail trace processing. When 1, the incoming data is inverted before being passed on for trail trace processing. Bit 0: Receive Bit Reordering Enable (RBRE) - When 0, bit reordering is disabled (The first bit received is the MSB TT.RIR.RTD[7] of the byte). When 1, bit reordering is enabled (The first bit received is the LSB TT.RIR.RTD[0] of the byte). 272 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: TT.RTIAR Trail Trace Receive Identifier Address Register (0,2,4,6)F2h Bit # Name Default 15 -- 0 14 -- 0 13 Reserved 0 12 Reserved 0 11 ETIA3 0 10 ETIA2 0 9 ETIA1 0 8 ETIA0 0 Bit # Name Default 7 -- 0 6 -- 0 5 Reserved 0 4 Reserved 0 3 RTIA3 0 2 RTIA2 0 1 RTIA1 0 0 RTIA0 0 Bits 11 to 8: Expected Trail Trace Identifier Address (ETIA[3:0]) - These four bits indicate the expected trail trace identifier byte to be read/written by the next memory access. Address 0h indicates the first byte of the expected trail trace identifier. Note: The value of these bits increments with each expected trail trace identifier memory access (when these bits are Fh, a memory access will return them to 0h). Bits 3 to 0: Receive Trail Trace Identifier Address (RTIA[3:0]) - These four bits indicate the receive trail trace identifier byte to be read by the next memory access. Address 0h indicates the first byte of the receive trail trace identifier. Note: The value of these bits increments with each receive trail trace identifier memory access (when these bits are Fh, a memory access will return them to 0h). Register Name: Register Description: Register Address: TT.RSR Trail Trace Receive Status Register (0,2,4,6)F4h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 -- 6 -- 5 -- 4 -- 3 -- 2 RTIM 1 RTIU 0 RIDL Bit 2: Receive Trail Trace Identifier Mismatch (RTIM) 0 = Received and expected trail trace identifiers match. 1 = Received and expected trail trace identifiers do not match; trail trace identifier mismatch (TIM) declared. Bit 1: Receive Trail Trace Identifier Unstable (RTIU) 0 = Received trail trace identifier is not unstable 1 = Received trail trace identifier is in an unstable condition (TIU); TIU is declared when eight consecutive trail trace identifiers are received that do not match either the receive trail trace identifier or the previously stored current trail trace identifier. Bit 0: Receive Trail Trace Identifier Idle (RIDL) 0 = Received trail trace identifier is not in idle condition. 1 = Received trail trace identifier is in idle condition. Idle condition is declared upon the reception of an all zeros trail trace identifier five consecutive times. 273 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: TT.RSRL Trail Trace Receive Status Register Latched (0,2,4,6)F6h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 -- 6 -- 5 -- 4 -- 3 RTICL 2 RTIML 1 RTIUL 0 RIDLL Bit 3: Receive Trail Trace Identifier Change Latched (RTICL) - This bit is set when the receive trail trace identifier is updated. Bit 2: Receive Trail Trace Identifier Mismatch Latched (RTIML) - This bit is set when the TT.RSR.RTIM bit transitions from 0 to 1. Bit 1: Receive Trail Trace Identifier Unstable Latched (RTIUL) - This bit is set when the TT.RSR.RTIU bit transitions from 0 to 1. Bit 0: Receive Trail Trace Identifier Idle Latched (RIDLL) - This bit is set when the TT.RSR.RIDL bit transitions from 0 to 1. Register Name: Register Description: Register Address: TT.RSRIE Trail Trace Receive Status Register Interrupt Enable (0,2,4,6)F8h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 -- 0 3 RTICIE 0 2 RTIMIE 0 1 RTIUIE 0 0 RIDLIE 0 Bit 3: Receive Trail Trace Identifier Change Interrupt Enable (RTICIE) - This bit enables an interrupt if the TT.RSRL.RTICL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 2: Receive Trail Trace Identifier Mismatch Interrupt Enable (RTIMIE) - This bit enables an interrupt if the TT.RSRL.RTIML bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 1: Receive Trail Trace Identifier Unstable Interrupt Enable (RTIUIE) - This bit enables an interrupt if the TT.RSRL.RTIUL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 0: Receive Trail Trace Identifier Idle Interrupt Enable (RIDLIE) - This bit enables an interrupt if the TT.RSRL.RIDLL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled 274 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: TT.RIR Trail Trace Receive Identifier Register (0,2,4,6)FCh Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 RTD7 0 6 RTD6 0 5 RTD5 0 4 RTD4 0 3 RTD3 0 2 RTD2 0 1 RTD1 0 0 RTD0 0 Bits 7 to 0: Receive Trail Trace Identifier Data (RTD[7:0]) - These eight bits are the receive trail trace identifier data. The receive trail trace identifier address will be incremented whenever these bits are read (when byte Fh is read, the address will return to 0h). Register Name: Register Description: Register Address: TT.EIR Trail Trace Expected Identifier Register (0,2,4,6)FEh Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 ETD7 0 6 ETD6 0 5 ETD5 0 4 ETD4 0 3 ETD3 0 2 ETD2 0 1 ETD1 0 0 ETD0 0 Bits 7 to 0: Expected Trail Trace Identifier Data (ETD[7:0]) - These eight bits are the expected trail trace identifier data. The expected trail trace identifier address will be incremented whenever these bits are read or written (when byte Fh is read or written, the address will return to 0h). 275 DS3181/DS3182/DS3183/DS3184 12.10 DS3/E3 Framer 12.10.1 Transmit DS3 The transmit DS3 uses two registers. Table 12-33. Transmit DS3 Framer Register Map ADDRESS REGISTER (1,3,5,7)18h (1,3,5,7)1Ah (1,3,5,7)1Ch (1,3,5,7)1Eh T3.TCR T3.TEIR -- -- REGISTER DESCRIPTION T3 Transmit Control Register T3 Transmit Error Insertion Register Reserved Reserved 12.10.1.1 Register Bit Descriptions Register Name: Register Description: Register Address: T3.TCR T3 Transmit Control Register (1,3,5,7)18h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 PBGE 0 11 TIDLE 0 10 CBGD 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 TFEBE 0 4 AFEBED 0 3 TRDI 0 2 ARDID 0 1 TFGC 0 0 TAIS 0 Bit 12: P-bit Generation Enable (PBGE) - When 0, Transmit Frame Processor P-bit generation is disabled. If transmit frame generation is also disabled, the P-bit overhead periods in the incoming DS3 signal will be passed through to overhead insertion. When 1, Transmit Frame Processor P-bit generation is enabled. The P-bit overhead periods in the incoming DS3 signal will be overwritten even if transmit frame generation is disabled Bit 11: Transmit DS3 Idle Signal (TIDLE) - 0 = Transmit DS3 Idle signal is not inserted 1 = Transmit DS3 Idle signal is inserted into the DS3 frame. Bit 10: C-bit Generation Disable (CBGD) (M23 mode only) - When 0, Transmit Frame Processor C-bit generation is enabled. The C-bit overhead periods in the incoming M23 DS3 signal will be overwritten with zeros. When 1, Transmit Frame Processor C-bit generation is disabled. The C-bit overhead periods in the incoming M23 DS3 signal will be treated as payload, and passed through to overhead insertion. This bit is ignored in C-bit DS3 mode. Note: If CBGD = 1, PORT.CR1.NAD must also be set to 1. Bit 5: Transmit FEBE Error (TFEBE) - When automatic far-end block error generation is defeated (AFEBED = 1), the inverse of this bit is inserted into the bits C41, C42, and C43. Note: a far-end block error value of zero (TFEBE=1) indicates a far-end block error. This bit is ignored in M23 DS3 mode. Bit 4: Automatic FEBE Defeat (AFEBED) - When 0, a far-end block error is automatically generated based upon the receive parity errors. When 1, a far-end block error is inserted from the register bit TFEBE. This bit is ignored in M23 DS3 mode. Bit 3: Transmit RDI Alarm (TRDI) - When automatic RDI generation is defeated (ARDID = 1), the inverse of this bit is inserted into the X-bits (X1 and X2). Note: an RDI value of zero (TRDI=1) indicates an alarm. Bit 2: Automatic RDI Defeat (ARDID) - When 0, the RDI is automatically generated based received DS3 alarms. When 1, the RDI is inserted from the register bit TRDI. 276 DS3181/DS3182/DS3183/DS3184 Bit 1: Transmit Frame Generation Control (TFGC) - When this bit is zero, the Transmit Frame Processor frame generation is enabled. The DS3 overhead positions in the incoming DS3 payload will be overwritten with the internally generated DS3 overhead. When this bit is one, the Transmit Frame Processor frame generation is disabled. The DS3 overhead positions in the incoming DS3 payload will be passed through to error insertion. Note: Frame generation will still overwrite the P-bits if PBGE = 1. Also, the DS3 overhead periods can still be overwritten by overhead insertion. Bit 0: Transmit Alarm Indication Signal (TAIS) - 0 = Transmit Alarm Indication Signal is not inserted 1 = Transmit Alarm Indication Signal is inserted into data stream payload 277 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: T3.TEIR T3 Transmit Error Insertion Register (1,3,5,7)1Ah Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 CCPEIE 0 10 CPEI 0 9 CFBEIE 0 8 FBEI 0 Bit # Name Default 7 Reserved 0 6 CPEIE 0 5 PEI 0 4 FEIC1 0 3 FEIC0 0 2 FEI 0 1 TSEI 0 0 MEIMS 0 Bit 11: Continuous C-bit Parity Error Insertion Enable (CCPEIE) - When 0, single C-bit parity error insertion is enabled. When 1, continuous C-bit parity error insertion is enabled, and C-bit parity errors will be transmitted continuously if CPEI is high. Bit 10: C-bit Parity Error Insertion Enable (CPEI) - When 0, C-bit parity error insertion is disabled. When 1, C-bit parity error insertion is enabled. Bit 9: Continuous Far-End Block Error Insertion Enable (CFBEIE) - When 0, single far-end block error insertion is enabled. When 1, continuous far-end block error insertion is enabled, and far-end block errors will be transmitted continuously if FBEI is high. Bit 8: Far-End Block Error Insertion Enable (FBEI) - When 0, far-end block error insertion is disabled. When 1, far-end block error insertion is enabled. Bit 6: Continuous P-bit Parity Error Insertion Enable (CPEIE) - When 0, single P-bit parity error insertion is enabled. When 1, continuous P-bit parity error insertion is enabled, and P-bit parity errors will be transmitted continuously if PEI is high. Bit 5: P-bit Parity Error Insertion Enable (PEI) - When 0, P-bit parity error insertion is disabled. When 1, P-bit parity error insertion is enabled. Bits 4 to 3: Framing Error Insertion Control (FEIC[1:0]) - These two bits control the framing error event to be inserted. 00 = F-bit error. 01 = M-bit error. 10 = SEF error. 11 = OOMF error. Bit 2: Framing Error Insertion Enable (FEI) - When 0, framing error insertion is disabled. When 1, framing error insertion is enabled. Bit 1: Transmit Single Error Insert (TSEI) - This bit causes an error of the enabled type(s) to be inserted in the transmit data stream if manual error insertion is disabled (MEIMS = 0). A 0 to 1 transition causes a single error to be inserted. For a second error to be inserted, this bit must be set to 0, and back to 1. Note: If MEIMS is low, and this bit transitions more than once between error insertion opportunities, only one error will be inserted. Bit 0: Manual Error Insert Mode Select (MEIMS) - When 0, error insertion is initiated by the TSEI register bit. When 1, error insertion is initiated by the transmit manual error insertion signal (TMEI). Note: If TMEI or TSEI is one, changing the state of this bit may cause an error to be inserted. 278 DS3181/DS3182/DS3183/DS3184 12.10.2 Receive DS3 Register Map The receive DS3 uses 11 registers. Two registers are shared for C-Bit and M23 DS3 modes. The M23 DS3 mode does not use the RFEBER or RCPECR count registers. Table 12-34. Receive DS3 Framer Register Map ADDRESS REGISTER (1,3,5,7)20h (1,3,5,7)22h (1,3,5,7)24h (1,3,5,7)26h (1,3,5,7)28h (1,3,5,7)2Ah (1,3,5,7)2Ch (1,3,5,7)2Eh (1,3,5,7)30h (1,3,5,7)32h (1,3,5,7)34h (1,3,5,7)36h (1,3,5,7)38h (1,3,5,7)3Ah (1,3,5,7)3Ch (1,3,5,7)3Eh T3.RCR -- T3.RSR1 T3.RSR2 T3.RSRL1 T3.RSRL2 T3.RSRIE1 T3.RSRIE2 -- -- T3.RFECR T3.RPECR T3.RFBECR T3.RCPECR -- -- REGISTER DESCRIPTION T3 Receive Control Register Reserved T3 Receive Status Register 1 T3 Receive Status Register 2 T3 Receive Status Register Latched 1 T3 Receive Status Register Latched 2 T3 Receive Status Register Interrupt Enable 1 T3 Receive Status Register Interrupt Enable 2 Reserved Reserved T3 Receive Framing Error Count Register T3 Receive P-Bit Parity Error Count Register T3 Receive Far-End Block Error Count Register T3 Receive C-Bit Parity Error Count Register Unused Unused 12.10.2.1 Register Bit Descriptions Register Name: Register Description: Register Address: T3.RCR T3 Receive Control Register (1,3,5,7)20h Bit # Name Default 15 Reserved 0 14 COVHD 0 13 MAOD 0 12 MDAISI 0 11 AAISD 0 10 ECC 0 9 FECC1 0 8 FECC0 0 Bit # Name Default 7 RAILE 0 6 RAILD 0 5 RAIOD 0 4 RAIAD 0 3 ROMD 0 2 LIP1 0 1 LIP0 0 0 FRSYNC 0 Bit 14: C-bit Overhead Masking Disable (COVHD) - When 0, the C-bit positions will be marked as overhead (RDENn=0). When 1, the C-bit positions will be marked as data (RDENn=1). This bit is ignored in C-bit DS3 mode or when the ROMD bit is set to one. Bit 13: Multiframe Alignment OOF Disable (MAOD) - When 0, an OOF condition is declared whenever an OOMF or SEF condition is declared. When 1, an OOF condition is declared only when an SEF condition is declared. Bit 12: Manual Downstream AIS Insertion (MDAISI) - When 0, manual downstream AIS insertion is disabled. When 1, manual downstream AIS insertion is enabled. Bit 11: Automatic Downstream AIS Disable (AAISD) - When 0, the presence of a LOS, OOF, or AIS condition will cause downstream AIS to be inserted. When 1, the presence of a LOS, OOF, or AIS condition will not cause downstream AIS to be inserted. Bit 10: Error Count Control (ECC) - When 0, framing errors, P-bit parity errors, C-bit parity errors, and far-end block errors will not be counted if an OOF or AIS condition is present. P-bit parity errors, C-bit parity errors, and farend block errors will also not be counted during the DS3 frame in which an OOF condition is terminated, and the next DS3 frame. When 1, framing errors, P-bit parity errors, C-bit parity errors, and far-end block errors will be counted regardless of the presence of an OOF or AIS condition. 279 DS3181/DS3182/DS3183/DS3184 Bits 9 to 8: Framing Error Count Control (FECC[1:0]) - These two bits control the type of framing error events that are counted. 00 = count OOF occurrences (counted regardless of the setting of the ECC bit). 01 = count M bit and F bit errors. 10 = count only F bit errors. 11 = count only M bit errors. Bit 7: Receive Alarm Indication on LOF Enable (RAILE) - When 0, an LOF condition does not affect the receive alarm indication signal (RAI). When 1, an LOF condition will cause the transmit DS3 X-bits to be set to zero if transmit automatic RDI is enabled. Bit 6: Receive Alarm Indication on LOS Disable (RAILD) - When 0, an LOS condition will cause the transmit DS3 X-bits to be set to zero if transmit automatic RDI is enabled. When 1, an LOS condition does not affect the RAI signal. Bit 5: Receive Alarm Indication on SEF Disable (RAIOD) - When 0, an SEF condition will cause the transmit DS3 X-bits to be set to zero if transmit automatic RDI is enabled. When 1, an SEF condition does not affect the RAI signal. Bit 4: Receive Alarm Indication on AIS Disable (RAIAD) - When 0, an AIS condition will cause the transmit DS3 X-bits to be set to zero if transmit automatic RDI is enabled. When 1, an AIS condition does not affect the RAI signal. Bit 3: Receive Overhead Masking Disable (ROMD) - When 0, the DS3 overhead positions in the outgoing DS3 payload will be marked as overhead by RDENn. When 1, the DS3 overhead positions in the outgoing DS3 payload will be marked as payload data by RDENn. When this bit is set to one, the COVHD bit is ignored. Bits 2 to 1: LOF Integration Period (LIP[1:0]) - These two bits determine the OOF integration period for declaring LOF. 00 = OOF is integrated for 3 ms before declaring LOF 01 = OOF is integrated for 2 ms before declaring LOF 10 = OOF is integrated for 1 ms before declaring LOF. 11 = LOF is declared at the same time as OOF. Bit 0: Force Framer Re-synchronization (FRSYNC) - A 0 to 1 transition forces an OOF, SEF, and OOMF condition. The bit must be cleared and set to one again to force another re-synchronization 280 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: T3.RSR1 T3 Receive Status Register 1 (1,3,5,7)24h Bit # Name 15 Reserved 14 Reserved 13 -- 12 Reserved 11 T3FM 10 AIC 9 IDLE 8 RUA1 Bit # Name 7 OOMF 6 SEF 5 -- 4 LOF 3 RDI 2 AIS 1 OOF 0 LOS Bit 11: T3 Framing Format Mismatch (T3FM) - This bit indicates the DS3 framer is programmed for a framing format (C-bit or M23) that is different than the format indicated by the incoming DS3 signal. Bit 10: Application Identification Channel (AIC) - This bit indicates the current state of the Application Identification Channel (AIC) from the C11 bit. AIC = 1 is C-bit mode, AIC = 0 is M23 mode. Bit 9: DS3 Idle Signal (IDLE) - When 0, the receive frame processor is not in a DS3 idle signal (Idle) condition. When 1, the receive frame processor is in an Idle condition. Bit 8: Receive Unframed All 1's (RUA1) - When 0, the receive frame processor is not in a receive unframed all 1's (RUA1) condition. When 1, the receive frame processor is in an RUA1 condition. Bit 7: Out Of Multiframe (OOMF) - When 0, the receive frame processor is not in an out of multiframe (OOMF) condition. When 1, the receive frame processor is in an OOMF condition. Bit 6: Severely Errored Frame (SEF) - When 0, the receive frame processor is not in a severely errored frame (SEF) condition. When 1, the receive frame processor is in an SEF condition. Bit 4: Loss Of Frame (LOF) - When 0, the receive framer is not in a loss of frame (LOF) condition. When 1, the receive frame processor is in an LOF condition. Bit 3: Remote Defect Indication (RDI) - This bit indicates the current state of the remote defect indication (RDI) Bit 2: Alarm Indication Signal (AIS) - When 0, the receive frame processor is not in an alarm indication signal (AIS) condition. When 1, the receive frame processor is in an AIS condition. Bit 1: Out Of Frame (OOF) - When 0, the receive framer is not in an out of frame (OOF) condition. When 1, the receive frame processor is in an OOF condition. Bit 0: Loss Of Signal (LOS) - When 0, the receive framer is not in a loss of signal (LOS) condition. When 1, the receive framer is in an LOS condition. 281 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: T3.RSR2 T3 Receive Status Register 2 (1,3,5,7)26h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 -- 6 -- 5 -- 4 -- 3 CPEC 2 FBEC 1 PEC 0 FEC Bit 3: C-bit Parity Error Count (CPEC) - When 0, the C-bit parity error count is zero. When 1, the C-bit parity error count is one or more. This bit is set to zero in M23 DS3 mode. Bit 2: Remote Error Indication Count (FBEC) - When 0, the remote error indication count is zero. When 1, the remote error indication count is one or more. This bit is set to zero in M23 DS3 mode. Bit 1: P-bit Parity Error Count (PEC) - When 0, the P-bit parity error count is zero. When 1, the P-bit parity error count is one or more. Bit 0: Framing Error Count (FEC) - When 0, the framing error count is zero. When 1, the framing error count is one or more. The type of framing error event counted is determined by T3.RCR.FECC[1:0] Register Name: Register Description: Register Address: T3.RSRL1 T3 Receive Status Register Latched 1 (1,3,5,7)28h Bit # Name 15 Reserved 14 Reserved 13 Reserved 12 Reserved 11 T3FML 10 AICL 9 IDLEL 8 RUA1L Bit # Name 7 OOMFL 6 SEFL 5 COFAL 4 LOFL 3 RAIL 2 AISL 1 OOFL 0 LOSL Bit 11: T3 Framing Format Mismatch Latched (T3FML) - This bit is set when the T3FM bit transitions from zero to one. Bit 10: Application Identification Channel Change Latched (AICL) - This bit is set when the AIC bit changes state. Bit 9: DS3 Idle Signal Change Latched (IDLEL) - This bit is set when the IDLE bit changes state. Bit 8: Receive Unframed All 1's Change Latched (RUA1L) - This bit is set when the RUA1 bit changes state. Bit 7: Out Of Multiframe Change Latched (OOMFL) - This bit is set when the OOMF bit changes state. Bit 6: Severely Errored Frame Change Latched (SEFL) - This bit is set when the SEF bit changes state. Bit 5: Change Of Frame Alignment Latched (COFAL) - This bit is set when the data path frame counters are updated with a new DS3 frame alignment that is different from the previous DS3 frame alignment. Bit 4: Loss Of Frame Change Latched (LOFL) - This bit is set when the LOF bit changes state. Bit 3: Remote Defect Indication Change Latched (RDIL) - This bit is set when the RDI bit changes state. Bit 2: Alarm Indication Signal Change Latched (AISL) - This bit is set when the AIS bit changes state. Bit 1: Out Of Frame Change Latched (OOFL) - This bit is set when the OOF bit changes state. Bit 0: Loss Of Signal Change Latched (LOSL) - This bit is set when the LOS bit changes state. 282 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: T3.RSRL2 T3 Receive Status Register Latched 2 (1,3,5,7)2Ah Bit # Name 15 -- 14 -- 13 -- 12 -- 11 CPEL 10 FBEL 9 PEL 8 FEL Bit # Name 7 -- 6 -- 5 -- 4 -- 3 CPECL 2 FBECL 1 PECL 0 FECL Bit 11: C-bit Parity Error Latched (CPEL) - This bit is set when a C-bit parity error is detected. This bit is set to zero in M23 DS3 mode. Bit 10: Remote Error Indication Latched (FBEL) - This bit is set when a far-end block error is detected. This bit is set to zero in M23 DS3 mode. Bit 9: P-bit Parity Error Latched (PEL) - This bit is set when a P-bit parity error is detected. Bit 8: Framing Error Latched (FEL) - This bit is set when a framing error is detected. The type of framing error event that causes this bit to be set is determined by T3.RCR.FECC[1:0] Bit 3: C-bit Parity Error Count Latched (CPECL) - This bit is set when the CPEC bit transitions from zero to one. This bit is set to zero in M23 DS3 mode. Bit 2: Remote Error Indication Count Latched (FBECL) - This bit is set when the FBEC bit transitions from zero to one. This bit is set to zero in M23 DS3 mode. Bit 1: P-bit Parity Error Count Latched (PECL) - This bit is set when the PEC bit transitions from zero to one. Bit 0: Framing Error Count Latched (FECL) - This bit is set when the FEC bit transitions from zero to one. 283 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: T3.RSRIE1 T3 Receive Status Register Interrupt Enable 1 (1,3,5,7)2Ch Bit # Name Default 15 Reserved 0 14 Reserved 0 13 Reserved 0 12 Reserved 0 11 T3FMIE 0 10 AICIE 0 9 IDLEIE 0 8 RUA1IE 0 Bit # Name Default 7 OOMFIE 0 6 SEFIE 0 5 COFAIE 0 4 LOFIE 0 3 RAIIE 0 2 AISIE 0 1 OOFIE 0 0 LOSIE 0 Bit 11: T3 Framing Format Mismatch Interrupt Enable (T3FMIE) - This bit enables an interrupt if the T3FML bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 10: Application Identification Channel Interrupt Enable (AICIE) - This bit enables an interrupt if the AICL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 9: DS3 Idle Signal Change Interrupt Enable (IDLEIE) - This bit enables an interrupt if the IDLEL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 8: Receive Unframed All 1's Interrupt Enable (RUA1IE) - This bit enables an interrupt if the RUA1L bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 7: Out Of Multiframe Interrupt Enable (OOMFIE) - This bit enables an interrupt if the OOMFL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 6: Severely Errored Frame Interrupt Enable (SEFIE) - This bit enables an interrupt if the SEFL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 5: Change Of Frame Alignment Interrupt Enable (COFAIE) - This bit enables an interrupt if the COFAL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 4: Loss Of Frame Interrupt Enable (LOFIE) - This bit enables an interrupt if the LOFL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 3: Remote Defect Indication Interrupt Enable (RDIIE) - This bit enables an interrupt if the RDIL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled 284 DS3181/DS3182/DS3183/DS3184 Bit 2: Alarm Indication Signal Interrupt Enable (AISIE) - This bit enables an interrupt if the AISL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 1: Out Of Frame Interrupt Enable (OOFIE) - This bit enables an interrupt if the OOFL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 0: Loss Of Signal Interrupt Enable (LOSIE) - This bit enables an interrupt if the LOSL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled 285 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: T3.RSRIE2 T3 Receive Status Register Interrupt Enable 2 (1,3,5,7)2Eh Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 CPEIE 0 10 FBEIE 0 9 PEIE 0 8 FEIE 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 -- 0 3 CPECIE 0 2 FBECIE 0 1 PECIE 0 0 FECIE 0 Bit 11: C-bit Parity Error Interrupt Enable (CPEIE) - This bit enables an interrupt if the CPEL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 10: Remote Error Interrupt Enable (FBEIE) - This bit enables an interrupt if the FBEL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 9: P-bit Parity Error Interrupt Enable (PEIE) - This bit enables an interrupt if the PEL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 8: Framing Error Interrupt Enable (FEIE) - This bit enables an interrupt if the FEL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 3: C-bit Parity Error Count Interrupt Enable (CPECIE) - This bit enables an interrupt if the CPECL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 2: Far-End Block Error Count Interrupt Enable (FBECIE) - This bit enables an interrupt if the FBECL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 1: P-bit Parity Error Count Interrupt Enable (PECIE) - This bit enables an interrupt if the PECL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 0: Framing Error Count Interrupt Enable (FECIE) - This bit enables an interrupt if the FECL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled 286 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: Bit # Name Default 15 FE15 0 T3.RFECR T3 Receive Framing Error Count Register (1,3,5,7)34h 14 FE14 0 13 FE13 0 12 FE12 0 11 FE11 0 10 FE10 0 9 FE9 0 8 FE8 0 Bit # 7 6 5 4 3 2 1 0 Name FE7 FE6 FE5 FE4 FE3 FE2 FE1 FE0 Default 0 0 0 0 0 0 0 0 Bits 15 to 0: Framing Error Count (FE[15:0]) - These 16 bits indicate the number of framing error events on the incoming DS3 data stream. This register is updated via the PMU signal (see Section 10.4.5) Register Name: Register Description: Register Address: T3.RPECR T3 Receive P-Bit Parity Error Count Register (1,3,5,7)36h Bit # Name Default 15 PE15 0 14 PE14 0 13 PE13 0 12 PE12 0 11 PE11 0 10 PE10 0 9 PE9 0 8 PE8 0 Bit # Name Default 7 PE7 0 6 PE6 0 5 PE5 0 4 PE4 0 3 PE3 0 2 PE2 0 1 PE1 0 0 PE0 0 Bits 15 to 0: P-bit Parity Error Count (PE[15:0]) - These 16 bits indicate the number of P-bit parity errors detected on the incoming DS3 data stream. This register is updated via the PMU signal (see Section 10.4.5) Register Name: Register Description: Register Address: T3.RFBECR T3 Receive Far-End Block Error Count Register (1,3,5,7)38h Bit # Name Default 15 FBE15 0 14 FBE14 0 13 FBE13 0 12 FBE12 0 11 FBE11 0 10 FBE10 0 9 FBE9 0 8 FBE8 0 Bit # Name Default 7 FBE7 0 6 FBE6 0 5 FBE5 0 4 FBE4 0 3 FBE3 0 2 FBE2 0 1 FBE1 0 0 FBE0 0 Bits 15 to 0: Far-End Block Error Count (FBE[15:0]) - These 16 bits indicate the number of far-end block errors detected on the incoming DS3 data stream. The associated counter will not increment in M23 DS3 mode. This register is updated via the PMU signal (see Section 10.4.5) 287 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: T3.RCPECR T3 Receive C-Bit Parity Error Count Register (1,3,5,7)3Ah Bit # Name Default 15 CPE15 0 14 CPE14 0 13 CPE13 0 12 CPE12 0 11 CPE11 0 10 CPE10 0 9 CPE9 0 8 CPE8 0 Bit # Name Default 7 CPE7 0 6 CPE6 0 5 CPE5 0 4 CPE4 0 3 CPE3 0 2 CPE2 0 1 CPE1 0 0 CPE0 0 Bits 15 to 0: C-bit Parity Error Count (CPE[15:0]) - These 16 bits indicate the number of C-bit parity errors detected on the incoming DS3 data stream. The associated counter will not increment in M23 DS3 mode. This register is updated via the PMU signal (see Section 10.4.5). 288 DS3181/DS3182/DS3183/DS3184 12.10.3 Transmit G.751 E3 The transmit G.751 E3 uses two registers. 12.10.3.1 Register Map Table 12-35. Transmit G.751 E3 Framer Register Map ADDRESS (1,3,5,7)18h (1,3,5,7)1Ah (1,3,5,7)1Ch (1,3,5,7)1Eh REGISTER E3G751.TCR E3G751.TEIR -- -- REGISTER DESCRIPTION E3 G.751 Transmit Control Register E3 G.751 Transmit Error Insertion Register Reserved Reserved 12.10.3.2 Register Bit Descriptions Register Name: Register Description: Register Address: E3G751.TCR E3 G.751 Transmit Control Register (1,3,5,7)18h Bit # Name Default 15 Reserved 0 14 -- 0 13 -- 0 12 Reserved 0 11 Reserved 0 10 Reserved 0 9 TNBC1 0 8 TNBC0 0 Bit # Name Default 7 -- 0 6 -- 0 5 Reserved 0 4 Reserved 0 3 TABC1 0 2 TABC0 0 1 TFGC 0 0 TAIS 0 Bits 9 to 8: Transmit N Bit Control (TNBC[1:0]) - These two bits control the source of the N bit. 00 = 1 01 = transmit data from HDLC controller. 10 = transmit data from FEAC controller. 11 = 0 Note: If TNBC[1:0] is 10 and TABC[1:0] is 01, both the N bit and A bit will carry the same transmit FEAC controller (one bit per frame period), however, the N bit and A bit in the same frame may or may not be equal. Bits 3 to 2: Transmit A Bit Control (TABC[1:0]) - These two bits control the source of the A bit. 00 = automatically generated based upon received E3 alarms. 01 = transmit from the FEAC controller. 10 = 0 11 = 1 Note: If TABC[1:0] is 01 and TNBC[1:0] is 10, both the A bit and N bit will carry the same transmit FEAC controller (one bit per frame period), however, the A bit and N bit in the same frame may or may not be equal. Bit 1: Transmit Frame Generation Control (TFGC) - When this bit is zero, the Transmit Frame Processor frame generation is enabled. The E3 overhead positions in the incoming E3 payload will be overwritten with the internally generated E3 overhead. When this bit is one, the Transmit Frame Processor frame generation is disabled. The E3 overhead positions in the incoming E3 payload will be passed through to error insertion. Note: The E3 overhead periods can still be overwritten by overhead insertion. Bit 0: Transmit Alarm Indication Signal (TAIS) - When 0, the normal signal is transmitted. When 1, the output E3 data stream is forced to all ones (AIS). 289 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: E3G751.TEIR E3 G.751 Transmit Error Insertion Register (1,3,5,7)1Ah Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 Reserved 0 10 Reserved 0 9 Reserved 0 8 Reserved 0 Bit # Name Default 7 Reserved 0 6 Reserved 0 5 Reserved 0 4 FEIC1 0 3 FEIC0 0 2 FEI 0 1 TSEI 0 0 MEIMS 0 Bits 4 to 3: Framing Error Insert Control (FEIC[1:0]) - These two bits control the framing error event to be inserted. 00 = single bit error in one frame. 01 = word error in one frame. 10 = single bit error in four consecutive frames. 11 = word error in four consecutive frames. Bit 2: Framing Error Insertion Enable (FEI) - When 0, framing error insertion is disabled. When 1, framing error insertion is enabled. Bit 1: Transmit Single Error Insert (TSEI) - This bit causes an error of the enabled type(s) to be inserted in the transmit data stream if manual error insertion is disabled (MEIMS = 0). A 0 to 1 transition causes a single error to be inserted. For a second error to be inserted, this bit must be set to 0, and back to 1. Note: If MEIMS is low, and this bit transitions more than once between error insertion opportunities, only one error will be inserted. Bit 0: Manual Error Insert Mode Select (MEIMS) - When 0, error insertion is initiated by the TSEI register bit. When 1, error insertion is initiated by the transmit manual error insertion signal (TMEI). Note: If TMEI or TSEI is one, changing the state of this bit may cause an error to be inserted. 290 DS3181/DS3182/DS3183/DS3184 12.10.4 Receive G.751 E3 Register Map The receive G.751 E3 uses eight registers. Table 12-36. Receive G.751 E3 Framer Register Map ADDRESS (1,3,5,7)20h (1,3,5,7)22h (1,3,5,7)24h (1,3,5,7)26h (1,3,5,7)28h (1,3,5,7)2Ah (1,3,5,7)2Ch (1,3,5,7)2Eh (1,3,5,7)30h (1,3,5,7)32h (1,3,5,7)34h (1,3,5,7)36h (1,3,5,7)38h (1,3,5,7)3Ah (1,3,5,7)3Ch (1,3,5,7)3Eh REGISTER E3G751.RCR -- E3G751.RSR1 E3G751.RSR2 E3G751.RSRL1 E3G751.RSRL2 E3G751.RSRIE1 E3G751.RSRIE2 -- -- E3G751.RFECR -- -- -- -- -- REGISTER DESCRIPTION E3 G.751 Receive Control Register Reserved E3 G.751 Receive Status Register 1 E3 G.751 Receive Status Register 2 E3 G.751 Receive Status Register Latched 1 E3 G.751 Receive Status Register Latched 2 E3 G.751 Receive Status Register Interrupt Enable 1 E3 G.751 Receive Status Register Interrupt Enable 2 Reserved Reserved E3 G.751 Receive Framing Error Count Register Reserved Reserved Reserved Unused Unused 12.10.4.1 Register Bit Descriptions Register Name: Register Description: Register Address: E3G751.RCR E3 G.751 Receive Control Register (1,3,5,7)20h Bit # Name Default 15 Reserved 0 14 Reserved 0 13 DLS 0 12 MDAISI 0 11 AAISD 0 10 ECC 0 9 FECC1 0 8 FECC0 0 Bit # Name Default 7 RAILE 0 6 RAILD 0 5 RAIOD 0 4 RAIAD 0 3 ROMD 0 2 LIP1 0 1 LIP0 0 0 FRSYNC 0 Bit 13: Receive FEAC Data Link Source (DLS) - When 0, the receive FEAC controller will be sourced from the N bit. When 1, the receive FEAC controller will be sourced from the A bit. Bit 12: Manual Downstream AIS Insertion (MDAISI) - When 0, manual downstream AIS insertion is disabled. When 1, manual downstream AIS insertion is enabled. Bit 11: Automatic Downstream AIS Disable (AAISD) - When 0, the presence of an LOS, OOF, or AIS condition will cause downstream AIS to be inserted. When 1, the presence of an LOS, OOF, or AIS condition will not cause downstream AIS to be inserted. Bit 10: Error Count Control (ECC) - When 0, framing errors will not be counted if an OOF or AIS condition is present. When 1, framing errors will be counted regardless of the presence of an OOF or AIS condition. Bits 9 to 8: Framing Error Count Control (FECC[1:0]) - These two bits control the type of framing error events that are counted. 00 = count OOF occurrences (counted regardless of the setting of the ECC bit). 01 = count each bit error in the FAS (up to 10 per frame). 10 = count frame alignment signal (FAS) errors (up to one per frame). 11 = reserved 291 DS3181/DS3182/DS3183/DS3184 Bit 7: Receive Alarm Indication on LOF Enable (RAILE) - When 0, an LOF condition does not affect the receive alarm indication signal (RAI). When 1, an LOF condition will cause the transmit E3 A bit to be set to one if transmit automatic RAI is enabled. Bit 6: Receive Alarm Indication on LOS Disable (RAILD) - When 0, an LOS condition will cause the transmit E3 A bit to be set to one if transmit automatic RAI is enabled. When 1, an LOS condition does not affect the RAI signal. Bit 5: Receive Alarm Indication on OOF Disable (RAIOD) - When 0, an OOF condition will cause the transmit E3 A bit to be set to one if transmit automatic RAI is enabled. When 1, an OOF condition does not affect the RAI signal. Bit 4: Receive Alarm Indication on AIS Disable (RAIAD) - When 0, an AIS condition will cause the transmit E3 A bit to be set to one if transmit automatic RAI is enabled. When 1, an AIS condition does not affect the RAI signal. Bit 3: Receive Overhead Masking Disable (ROMD) - When 0, the E3 overhead positions in the outgoing E3 payload will be marked as overhead by RDENn. When 1, the E3 overhead positions in the outgoing E3 payload will be marked as data by RDENn. Bits 2 to 1: LOF Integration Period (LIP[1:0]) - These two bits determine the OOF integration period for declaring LOF. 00 = OOF is integrated for 3 ms before declaring LOF 01 = OOF is integrated for 2 ms before declaring LOF. 10 = OOF is integrated for 1 ms before declaring LOF 11 = LOF is declared at the same time as OOF Bit 0: Force Framer Re-synchronization (FRSYNC) - A 0 to 1 transition forces an OOF condition at the FAS check. This bit must be cleared and set to one again to force another re-synchronization 292 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: E3G751.RSR1 E3 G.751 Receive Status Register 1 (1,3,5,7)24h Bit # Name 15 Reserved 14 Reserved 13 -- 12 Reserved 11 Reserved 10 Reserved 9 Reserved 8 RUA1 Bit # Name 7 RAB 6 RNB 5 -- 4 LOF 3 RDI 2 AIS 1 OOF 0 LOS Bit 8: Receive Unframed All 1's (RUA1) - When 0, the receive frame processor is not in a receive unframed all 1's (RUA1) condition. When 1, the receive frame processor is in an RUA1 condition. Bit 7: Receive A Bit (RAB) - This bit is the integrated A bit extracted from the E3 frame. Bit 6: Receive N Bit (RNB) - This bit is the integrated N bit extracted from the E3 frame. Bit 4: Loss Of Frame (LOF) - When 0, the receive frame processor is not in a loss of frame (LOF) condition. When 1, the receive frame processor is in an LOF condition. Bit 3: Remote Alarm Indication (RDI) - This bit indicates the current state of the remote alarm indication (RDI). Bit 2: Alarm Indication Signal (AIS) - When 0, the receive frame processor is not in an alarm indication signal (AIS) condition. When 1, the receive frame processor is in an AIS condition. Bit 1: Out Of Frame (OOF) - When 0, the receive frame processor is not in an out of frame (OOF) condition. When 1, the receive frame processor is in an OOF condition. Bit 0: Loss Of Signal (LOS) - When 0, the receive loss of signal (LOS) input (RLOS) is low. When 1, RLOS is high. Register Name: Register Description: Register Address: E3G751.RSR2 E3 G.751 Receive Status Register 2 (1,3,5,7)26h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 -- 6 -- 5 -- 4 -- 3 Reserved 2 Reserved 1 Reserved 0 FEC Bit 0: Framing Error Count (FEC) - When 0, the framing error count is zero. When 1, the framing error count is one or more. 293 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: E3G751.RSRL1 E3 G.751 Receive Status Register Latched 1 (1,3,5,7)28h Bit # Name 15 Reserved 14 Reserved 13 Reserved 12 Reserved 11 Reserved 10 Reserved 9 Reserved 8 RUA1L Bit # Name 7 ACL 6 NCL 5 COFAL 4 LOFL 3 RDIL 2 AISL 1 OOFL 0 LOSL Bit 8: Receive Unframed All 1's Change Latched (RUA1L) - This bit is set when the RUA1 bit changes state. Bit 7: A Bit Change Latched (ACL) - This bit is set when the RAB bit changes state. Bit 6: N Bit Change Latched (NCL) - This bit is set when the RNB bit changes state. Bit 5: Change Of Frame Alignment Latched (COFAL) - This bit is set when the data path frame counters are updated with a new frame alignment that is different from the previous frame alignment. Bit 4: Loss Of Frame Change Latched (LOFL) - This bit is set when the LOF bit changes state. Bit 3: Remote Alarm Indication Change Latched (RDIL) - This bit is set when the RDI bit changes state. Bit 2: Alarm Indication Signal Change Latched (AISL) - This bit is set when the AIS bit changes state. Bit 1: Out Of Frame Change Latched (OOFL) - This bit is set when the OOF bit changes state. Bit 0: Loss Of Signal Change Latched (LOSL) - This bit is set when the LOS bit changes state. Register Name: Register Description: Register Address: E3G751.RSRL2 E3 G.751 Receive Status Register Latched 2 (1,3,5,7)2Ah Bit # Name 15 -- 14 -- 13 -- 12 -- 11 Reserved 10 Reserved 9 Reserved 8 FEL Bit # Name 7 -- 6 -- 5 -- 4 -- 3 Reserved 2 Reserved 1 Reserved 0 FECL Bit 8: Framing Error Latched (FEL) - This bit is set when a framing error is detected. Bit 0: Framing Error Count Latched (FECL) - This bit is set when the FEC bit transitions from zero to one. 294 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: E3G751.RSRIE1 E3 G.751 Receive Status Register Interrupt Enable 1 (1,3,5,7)2Ch Bit # Name Default 15 Reserved 0 14 Reserved 0 13 Reserved 0 12 Reserved 0 11 Reserved 0 10 Reserved 0 9 Reserved 0 8 RUA1IE 0 Bit # Name Default 7 ACIE 0 6 NCIE 0 5 COFAIE 0 4 LOFIE 0 3 RDIIE 0 2 AISIE 0 1 OOFIE 0 0 LOSIE 0 Bit 8: Receive Unframed All 1's Interrupt Enable (RUA1IE) - This bit enables an interrupt if the RUA1L bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 7: A Bit Change Interrupt Enable (ACIE) - This bit enables an interrupt if the ACL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 6: N Bit Change Interrupt Enable (NCIE) - This bit enables an interrupt if the NCL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 5: Change Of Frame Alignment Interrupt Enable (COFAIE) - This bit enables an interrupt if the COFAL bit and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port are set. set. 0 = interrupt disabled 1 = interrupt enabled Bit 4: Loss Of Frame Interrupt Enable (LOFIE) - This bit enables an interrupt if the LOFL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 3: Remote Alarm Indication Interrupt Enable (RDIIE) - This bit enables an interrupt if the RDIL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 2: Alarm Indication Signal Interrupt Enable (AISIE) - This bit enables an interrupt if the AISL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 1: Out Of Frame Interrupt Enable (OOFIE) - This bit enables an interrupt if the OOFL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 0: Loss Of Signal Interrupt Enable (LOSIE) - This bit enables an interrupt if the LOSL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled 295 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: E3G751.RSRIE2 E3 G.751 Receive Status Register Interrupt Enable 2 (1,3,5,7)2Eh Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 Reserved 0 10 Reserved 0 9 Reserved 0 8 FEIE 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 -- 0 3 Reserved 0 2 Reserved 0 1 Reserved 0 0 FECIE 0 Bit 8: Framing Error Interrupt Enable (FEIE) - This bit enables an interrupt if the FEL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 0: Framing Error Count Interrupt Enable (FECIE) - This bit enables an interrupt if the FECL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Register Name: Register Description: Register Address: E3G751.RFECR E3 G.751 Receive Framing Error Count Register (1,3,5,7)34h Bit # Name Default 15 FE15 0 14 FE14 0 13 FE13 0 12 FE12 0 11 FE11 0 10 FE10 0 9 FE9 0 8 FE8 0 Bit # Name Default 7 FE7 0 6 FE6 0 5 FE5 0 4 FE4 0 3 FE3 0 2 FE2 0 1 FE1 0 0 FE0 0 Bits 15 to 0: Framing Error Count (FE[15:0]) - These 16 bits indicate the number of framing error events on the incoming E3 data stream. This register is updated via the PMU signal (see Section 10.4.5). 296 DS3181/DS3182/DS3183/DS3184 12.10.5 Transmit G.832 E3 Register Map The transmit G.832 E3 uses four registers. Table 12-37. Transmit G.832 E3 Framer Register Map ADDRESS REGISTER REGISTER DESCRIPTION (1,3,5,7)18h (1,3,5,7)1Ah (1,3,5,7)1Ch (1,3,5,7)1Eh E3G832.TCR E3G832.TEIR E3G832.TMABR E3G832.TNGBR E3 G.832 Transmit Control Register E3 G.832 Transmit Error Insertion Register E3 G.832 Transmit MA Byte Register E3 G.832 Transmit NR and GC Byte Register 12.10.5.1 Register Bit Descriptions Register Name: Register Description: Register Address: E3G832.TCR E3 G.832 Transmit Control Register (1,3,5,7)18h Bit # Name Default 15 Reserved 0 14 -- 0 13 -- 0 12 Reserved 0 11 Reserved 0 10 TGCC 0 9 TNRC1 0 8 TNRC0 0 Bit # Name Default 7 -- 0 6 -- 0 5 TFEBE 0 4 AFEBED 0 3 TRDI 0 2 ARDID 0 1 TFGC 0 0 TAIS 0 Bit 10: Transmit GC Byte Control (TGCC) - When 0, the GC byte is inserted from the transmit HDLC controller. When 1, the GC byte is inserted from the GC byte register. Note: If bit TGCC is 0 and TNRC[1:0] is 01, both the GC byte and NR byte will carry the same transmit HDLC controller (eight bits per frame period), however, the GC byte and NR byte in the same frame may or may not be equal. Bits 9 to 8: Transmit NR Byte Control (TNRC[1:0]) - These two bits control the source of the NR byte. Note: If TNRC[1:0] is 01 and TGCC is 0, both the NR byte and GC byte will carry the same transmit HDLC controller (eight bits per frame period), however, the NR byte and GC byte in the same frame may or may not be equal. 00 = all ones. 01 = transmit from the HDLC controller. 10 = transmit from the FEAC controller. 11 = NR byte register. Bit 5: Transmit REI Error (TFEBE) - When automatic REI generation is defeated (AFEBED = 1), this bit is inserted into the second bit of the MA byte. Bit 4: Automatic REI Defeat (AFEBED) - When 0, the REI is automatically generated based upon the transmit remote error indication (TREI) signal. When 1, the REI is inserted from the register bit TFEBE. Bit 3: Transmit RDI Alarm (TRDI) - When automatic RDI generation is defeated (ARDID = 1), this bit is inserted into the first bit of the MA byte. Bit 2: Automatic RDI Defeat (ARDID) - When 0, the RDI is automatically generated based upon the received E3 alarms. When 1, the RDI is inserted from the register bit TRDI. Bit 1: Transmit Frame Generation Control (TFGC) - When this bit is zero, the Transmit Frame Processor frame generation is enabled. The E3 overhead positions in the incoming E3 payload will be overwritten with the internally generated E3 overhead. When this bit is one, the Transmit Frame Processor frame generation is disabled. The E3 overhead positions in the incoming E3 payload will be passed through to error insertion. Note: The E3 overhead periods can still be overwritten by overhead insertion. Bit 0: Transmit Alarm Indication Signal (TAIS) - When 0, the normal signal is transmitted. When 1, the E3 output data stream is forced to all ones (AIS). 297 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: E3G832.TEIR E3 G.832 Transmit Error Insertion Register (1,3,5,7)1Ah Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 Reserved 0 10 Reserved 0 9 CFBEIE 0 8 FBEI 0 Bit # Name Default 7 PBEE 0 6 CPEIE 0 5 PEI 0 4 FEIC1 0 3 FEIC0 0 2 FEI 0 1 TSEI 0 0 MEIMS 0 Bit 9: Continuous Remote Error Indication Error Insertion Enable (CFBEIE) - When 0, single remote error indication (REI) error insertion is enabled. When 1, continuous REI error insertion is enabled, and REI errors will be transmitted continuously if FEBI is high. Bit 8: Remote Error Indication Error Insertion Enable (FBEI) - When 0, REI error insertion is disabled. When 1, REI error insertion is enabled. Bit 7: Parity Block Error Enable (PBEE) - When 0, a parity error is generated by inverting a single bit in the EM byte. When 1, a parity error is generated by inverting all eight bits in the EM byte. Bit 6: Continuous Parity Error Insertion Enable (CPEIE) - When 0, single parity (BIP-8) error insertion is enabled. When 1, continuous parity error insertion is enabled, and parity errors will be transmitted continuously if PEI is high. Bit 5: Parity Error Insertion Enable (PEI) - When 0, parity error insertion is disabled. When 1, parity error insertion is enabled. Bits 4 to 3: Framing Error Control (FEIC[1:0]) - These two bits control the framing error event to be inserted. 00 = single bit error in one frame. 01 = word error in one frame. 10 = single bit error in four consecutive frames. 11 = word error in four consecutive frames. Bit 2: Framing Error Insertion Enable (FEI) - When 0, framing error insertion is disabled. When 1, framing error insertion is enabled. Bit 1: Transmit Single Error Insert (TSEI) - This bit causes an error of the enabled type(s) to be inserted in the transmit data stream if manual error insertion is disabled (MEIMS = 0). A 0 to 1 transition causes a single error to be inserted. For a second error to be inserted, this bit must be set to 0, and back to 1. Note: If MEIMS is low, and this bit transitions more than once between error insertion opportunities, only one error will be inserted. Bit 0: Manual Error Insert Mode Select (MEIMS) - When 0, error insertion is initiated by the TSEI register bit. When 1, error insertion is initiated by the transmit manual error insertion signal (TMEI). Note: If TMEI or TSEI is one, changing the state of this bit may cause an error to be inserted. 298 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: E3G832.TMABR E3 G.832 Transmit MA Byte Register (1,3,5,7)1Ch Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 TPT2 0 6 TPT1 0 5 TPT0 0 4 TTIGD 0 3 TTI3 0 2 TTI2 0 1 TTI1 0 0 TTI0 0 Bits 7 to 5: Transmit Payload Type (TPT[2:0]) - These bits determines the value transmitted in the payload type (third, fourth, and fifth bits in the MA byte). Bit 4: Transmit Timing Source Indicator Bit Generation Disable (TTIGD) - When 0, the last three bits of the MA byte (MA[6:8]) are generated from the four timing source indicator bits TTI[3:0]. When 1, TTI[3] is ignored and TTI[2:0] are directly inserted into the last three bits of the MA byte. Bits 3 to 0: Transmit Timing Source Indication (TTI[3:0]) - These four bits make up the timing source indicator bits. Register Name: Register Description: Register Address: E3G832.TNGBR E3 G.832 Transmit NR and GC Byte Register (1,3,5,7)1Eh Bit # Name Default 15 TGC7 0 14 TGC6 0 13 TGC5 0 12 TGC4 0 11 TGC3 0 10 TGC2 0 9 TGC1 0 8 TGC0 0 Bit # Name Default 7 TNR7 0 6 TNR6 0 5 TNR5 0 4 TNR4 0 3 TNR3 0 2 TNR2 0 1 TNR1 0 0 TNR0 0 Bits 15 to 8: Transmit GC Byte (TGC[7:0]) - These eight bits are the GC byte to be inserted into the E3 frame. Bits 7 to 0: Transmit NR Byte (TNR[7:0]) - These eight bits are the NR byte to be inserted into the E3 frame. 299 DS3181/DS3182/DS3183/DS3184 12.10.6 Receive G.832 E3 Register Map The receive G.832 E3 uses 13 registers. Table 12-38. Receive G.832 E3 Framer Register Map ADDRESS REGISTER (1,3,5,7)20h (1,3,5,7)22h (1,3,5,7)24h (1,3,5,7)26h (1,3,5,7)28h (1,3,5,7)2Ah (1,3,5,7)2Ch (1,3,5,7)2Eh (1,3,5,7)30h (1,3,5,7)32h (1,3,5,7)34h (1,3,5,7)36h (1,3,5,7)38h (1,3,5,7)3Ah (1,3,5,7)3Ch (1,3,5,7)3Eh E3G832.RCR E3G832.RMACR E3G832.RSR1 E3G832.RSR2 E3G832.RSRL1 E3G751.RSRL2 E3G832.RSRIE1 E3G832.RSRIE2 E3G832.RMABR E3G832.RNGBR E3G832.RFECR E3G832.RPECR E3G832.RFBER -- -- -- REGISTER DESCRIPTION E3 G.832 Receive Control Register E3 G.832 Receive MA Byte Control Register E3 G.832 Receive Status Register 1 E3 G.832 Receive Status Register 2 E3 G.832 Receive Status Register Latched 1 E3 G.832 Receive Status Register Latched 2 E3 G.832 Receive Status Register Interrupt Enable 1 E3 G.832 Receive Status Register Interrupt Enable 2 E3 G.832 Receive MA Byte Register E3 G.832 Receive NR and GC Byte Register E3 G.832 Receive Framing Error Count Register E3 G.832 Receive Parity Error Count Register E3 G.832 Receive Remote Error Indication Count Register Reserved Unused Unused 12.10.6.1 Register Bit Descriptions Register Name: Register Description: Register Address: E3G832.RCR E3 G.832 Receive Control Register (1,3,5,7)20h Bit # Name Default 15 Reserved 0 14 PEC 0 13 DLS 0 12 MDAISI 0 11 AAISD 0 10 ECC 0 9 FECC1 0 8 FECC0 0 Bit # Name Default 7 RDILE 0 6 RDILD 0 5 RDIOD 0 4 RDIAD 0 3 ROMD 0 2 LIP1 0 1 LIP0 0 0 FRSYNC 0 Bit 14: Parity Error Count (PEC) - When 0, BIP-8 block errors (EM byte) are detected (no more than one per frame). When 1, BIP-8-bit errors are detected (up to 8 per frame). Bit 13: Receive HDLC Data Link Source (DLS) - When 0, the receive HDLC data link will be sourced from the GC byte. When 1, the receive HDLC data link will be sourced from the NR byte. Bit 12: Manual Downstream AIS Insertion (MDAISI) - When 0, manual downstream AIS insertion is disabled. When 1, manual downstream AIS insertion is enabled. Bit 11: Automatic Downstream AIS Disable (AAISD) - When 0, the presence of an LOS, OOF, or AIS condition will cause downstream AIS to be inserted. When 1, the presence of an LOS, OOF, or AIS condition will not cause downstream AIS to be inserted. Bit 10: Error Count Control (ECC) - When 0, framing errors, parity errors, and REI errors will not be counted if an OOF or AIS condition is present. Parity errors and REI errors will also not be counted during the E3 frame in which an OOF or AIS condition is terminated, and the next E3 frame. When 1, framing errors, parity errors, and REI errors will be counted regardless of the presence of an OOF or AIS condition. 300 DS3181/DS3182/DS3183/DS3184 Bits 9 to 8: Framing Error Count Control (FECC[1:0]) - These two bits control the type of framing error events that are counted. 00 = count OOF occurrences (counted regardless of the setting of the ECC bit).. 01 = count each bit error in FA1 and FA2 (up to 16 per frame). 10 = count frame alignment word (FA1 and FA2) errors (up to one per frame). 11 = count FA1 byte errors and FA2 byte errors (up to 2 per frame). Bit 7: Receive Defect Indication on LOF Enable (RDILE) - When 0, an LOF condition does not affect the receive defect indication signal (RDI). When 1, an LOF condition will cause the transmit E3 RDI bit to be set to one if transmit automatic RDI is enabled. Bit 6: Receive Defect Indication on LOS Disable (RDILD) - When 0, an LOS condition will cause the transmit E3 RDI bit to be set to one if transmit automatic RDI is enabled. When 1, an LOS condition does not affect the RDI signal. Bit 5: Receive Defect Indication on OOF Disable (RDIOD) - When 0, an OOF condition will cause the transmit E3 RDI bit to be set to one if transmit automatic RDI is enabled. When 1, an OOF condition does not affect the RDI signal. Bit 4: Receive Defect Indication on AIS Disable (RDIAD) - When 0, an AIS condition will cause the transmit E3 RDI bit to be set to one if transmit automatic RDI is enabled. When 1, an AIS condition does not affect the RDI signal. Bit 3: Receive Overhead Masking Disable (ROMD) - When 0, the E3 overhead positions in the outgoing E3 payload will be marked as overhead by RDENn. When 1, the E3 overhead positions in the outgoing E3 payload will be marked as data by RDENn. Bits 2 to 1: LOF Integration Period (LIP[1:0]) - These two bits determine the OOF integration period for declaring LOF. 00 = OOF is integrated for 3 ms before declaring LOF. 01 = OOF is integrated for 2 ms before declaring LOF. 10 = OOF is integrated for 1 ms before declaring LOF. 11 = LOF is declared at the same time as OOF. Bit 0: Force Framer Re-synchronization (FRSYNC) - A 0 to 1 transition forces. an OOF condition at the next framing word check. This bit must be cleared and set to one again to force another re-synchronization. Register Name: Register Description: Register Address: E3G832.RMACR E3 G.832 Receive MA Byte Control Register (1,3,5,7)22h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 -- 0 3 EPT2 0 2 EPT1 0 1 EPT0 0 0 TIED 0 Bits 3 to 1: Expected Payload Type (EPT[2:0]) - These three bits contain the expected value of the payload type. Bit 0: Timing Source Indicator Bit Extraction Disable (TIED) - When 0, the four timing source indications bits are extracted from the last three bits of the MA byte (MA[6:8]), and stored in a register. When 1, timing source indicator bit extraction is disabled, and the last three bits of the MA byte are integrated and stored in a register. 301 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: E3G832.RSR1 E3 G.832 Receive Status Register 1 (1,3,5,7)24h Bit # Name 15 Reserved 14 -- 13 -- 12 RPTU 11 RPTM 10 Reserved 9 Reserved 8 RUA1 Bit # Name 7 Reserved 6 Reserved 5 -- 4 LOF 3 RAI 2 AIS 1 OOF 0 LOS Bit 12: Receive Payload Type Unstable (RPTU) - When 0, the receive payload type is stable. When 1, the receive payload type is unstable. Bit 11: Receive Payload Type Mismatch (RPTM) - When 0, the receive payload type and expected payload type match. When 1, the receive payload type and expected payload type do not match. Bit 8: Receive Unframed All 1's (RUA1) - When 0, the receive frame processor is not in a receive unframed all 1's (RUA1) condition. When 1, the receive frame processor is in an RUA1 condition. Bit 4: Loss Of Frame (LOF) - When 0, the receive frame processor is not in a loss of frame (LOF) condition. When 1, the receive frame processor is in an LOF condition. Bit 3: Remote Defect Indication (RDI) - This bit indicates the current state of the remote defect indication (RDI). Bit 2: Alarm Indication Signal (AIS) - When 0, the receive frame processor is not in an alarm indication signal (AIS) condition. When 1, the receive frame processor is in an AIS condition. Bit 1: Out Of Frame (OOF) - When 0, the receive frame processor is not in an out of frame (OOF) condition. When 1, the receive frame processor is in an OOF condition. Bit 0: Loss Of Signal (LOS) - When 0, the receive loss of signal (LOS) input (RLOS) is low. When 1, RLOS is high. Register Name: Register Description: Register Address: E3G832.RSR2 E3 G.832 Receive Status Register 2 (1,3,5,7)26h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 -- 6 -- 5 -- 4 -- 3 Reserved 2 FBEC 1 PEC 0 FEC Bit 2: Remote Error Indication Count (FBEC) - When 0, the remote error indication count is zero. When 1, the remote error indication count is one or more. Bit 1: Parity Error Count (PEC) - When 0, the parity error count is zero. When 1, the parity error count is one or more. Bit 0: Framing Error Count (FEC) - When 0, the framing error count is zero. When 1, the framing error count is one or more. 302 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: E3G832.RSRL1 E3 G.832 Receive Status Register Latched 1 (1,3,5,7)28h Bit # Name 15 Reserved 14 -- 13 TIL 12 RPTUL 11 RPTML 10 RPTL 9 Reserved 8 RUA1L Bit # Name 7 GCL 6 NRL 5 COFAL 4 LOFL 3 RDIL 2 AISL 1 OOFL 0 LOSL Bit 13: Timing Source Indication Change Latched (TIL) - This bit is set when the TI[3:0] bits change state. Bit 12: Receive Payload Type Unstable Latched (RPTUL) - This bit is set when the RPTU bit transitions from zero to one. Bit 11: Receive Payload Type Mismatch Latched (RPTML) - This bit is set when the RPTM bit transitions from zero to one. Bit 10: Receive Payload Type Change Latched (RPTL) - This bit is set when the RPT[2:0] bits change state. Bit 8: Receive Unframed All 1's Change Latched (RUA1L) - This bit is set when the RUA1 bit changes state. Bit 7: GC Byte Change Latched (GCL) - This bit is set when the RGC byte changes state. Bit 6: NR Byte Change Latched (NRL) - This bit is set when the RNR byte changes state. Bit 5: Change Of Frame Alignment Latched (COFAL) - This bit is set when the data path frame counters are updated with a new frame alignment that is different from the previous frame alignment. Bit 4: Loss Of Frame Change Latched (LOFL) - This bit is set when the LOF bit changes state. Bit 3: Remote Defect Indication Change Latched (RDIL) - This bit is set when the RDI bit changes state. Bit 2: Alarm Indication Signal Change Latched (AISL) - This bit is set when the AIS bit changes state. Bit 1: Out Of Frame Change Latched (OOFL) - This bit is set when the OOF bit changes state. Bit 0: Loss Of Signal Change Latched (LOSL) - This bit is set when the LOS bit changes state. Register Name: Register Description: Register Address: E3G832.RSRL2 E3 G.832 Receive Status Register Latched #2 (1,3,5,7)2Ah Bit # Name 15 -- 14 -- 13 -- 12 -- 11 Reserved 10 FBEL 9 PEL 8 FEL Bit # Name 7 -- 6 -- 5 -- 4 -- 3 Reserved 2 FBECL 1 PECL 0 FECL Bit 10: Remote Error Indication Latched (FBEL) - This bit is set when a remote error indication is detected. Bit 9: Parity Error Latched (PEL) - This bit is set when a BIP-8 parity error is detected. Bit 8: Framing Error Latched (FEL) - This bit is set when a framing error is detected. Bit 2: Remote Error Indication Count Latched (FBECL) - This bit is set when the FBEC bit transitions from zero to one. Bit 1: Parity Error Count Latched (PECL) - This bit is set when the PEC bit transitions from zero to one. Bit 0: Framing Error Count Latched (FECL) - This bit is set when the FEC bit transitions from zero to one. 303 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: E3G832.RSRIE1 E3 G.832 Receive Status Register Interrupt Enable 1 (1,3,5,7)2Ch Bit # Name Default 15 Reserved 0 14 -- 0 13 TIIE 0 12 RPTUIE 0 11 RPTMIE 0 10 RPTIE 0 9 Reserved 0 8 RUA1IE 0 Bit # Name Default 7 GCIE 0 6 NRIE 0 5 COFAIE 0 4 LOFIE 0 3 RAIIE 0 2 AISIE 0 1 OOFIE 0 0 LOSIE 0 Bit 13: Timing Indication Interrupt Enable (TIIE) - This bit enables an interrupt if the TIL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 12: Receive Payload Type Unstable Interrupt Enable (RPTUIE) - This bit enables an interrupt if the RPTUL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 11: Receive Payload Type Mismatch Interrupt Enable (RPTMIE) - This bit enables an interrupt if the RPTML bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 10: Receive Payload Type Interrupt Enable (RPTIE) - This bit enables an interrupt if the RPTL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 8: Receive Unframed All 1's Interrupt Enable (RUA1IE) - This bit enables an interrupt if the RUA1L bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 7: GC Byte Interrupt Enable (GCIE) - This bit enables an interrupt if the GCL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 6: NR Byte Interrupt Enable (NRIE) - This bit enables an interrupt if the NRL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 5: Change Of Frame Alignment Interrupt Enable (COFAIE) - This bit enables an interrupt if the COFAL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 4: Loss Of Frame Interrupt Enable (LOFIE) - This bit enables an interrupt if the LOFL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled 304 DS3181/DS3182/DS3183/DS3184 Bit 3: Remote Defect Indication Interrupt Enable (RDIIE) - This bit enables an interrupt if the RDIL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 2: Alarm Indication Signal Interrupt Enable (AISIE) - This bit enables an interrupt if the AISL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 1: Out Of Frame Interrupt Enable (OOFIE) - This bit enables an interrupt if the OOFL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 0: Loss Of Signal Interrupt Enable (LOSIE) - This bit enables an interrupt if the LOSL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled 305 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: E3G832.RSRIE2 E3 G.832 Receive Status Register Interrupt Enable 2 (1,3,5,7)2Eh Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 Reserved 0 10 FBEIE 0 9 PEIE 0 8 FEIE 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 -- 0 3 Reserved 0 2 FBECIE 0 1 PECIE 0 0 FECIE 0 Bit 10: Remote Error Indication Interrupt Enable (FBEIE) - This bit enables an interrupt if the FBEL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 9: Parity Error Interrupt Enable (PEIE) - This bit enables an interrupt if the PEL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 8: Framing Error Interrupt Enable (FEIE) - This bit enables an interrupt if the FEL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 2: Remote Error Indication Count Interrupt Enable (FBECIE) - This bit enables an interrupt if the FBECL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 1: Parity Error Count Interrupt Enable (PECIE) - This bit enables an interrupt if the PECL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 0: Framing Error Count Interrupt Enable (FECIE) - This bit enables an interrupt if the FECL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled 306 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: E3G832.RMABR E3 G.832 Receive MA Byte Register (1,3,5,7)30h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 RPT2 0 5 RPT1 0 4 RPT0 0 3 TI3 0 2 TI2 0 1 TI1 0 0 TI0 0 Bits 6 to 4: Receive Payload Type (RPT[2:0]) - These three bits are the integrated version of the payload type (MA[3:5]) from the MA byte. Bits 3 to 0: Receive Timing Source Indication (TI[3:0]) - When timing source indicator extraction is enabled, these four bits are the integrated version of the four timing source indicator bits extracted from the last three bits of the MA byte (MA[6:8]). When timing source indicator bit extraction is disabled, TI[3] is zero, and TI[2:0] contain the integrated version of the last three bits of the MA byte. Register Name: Register Description: Register Address: E3G832.RNGBR E3 G.832 Receive NR and GC Byte Register (1,3,5,7)32h Bit # Name Default 15 RGC7 0 14 RGC6 0 13 RGC5 0 12 RGC4 0 11 RGC3 0 10 RGC2 0 9 RGC1 0 8 RGC0 0 Bit # Name Default 7 RNR7 0 6 RNR6 0 5 RNR5 0 4 RNR4 0 3 RNR3 0 2 RNR2 0 1 RNR1 0 0 RNR0 0 Bits 15 to 8: Receive GC Byte (RGC[7:0]) - These eight bits are the integrated version of the GC byte as extracted from the E3 frame. Bits 7 to 0: Receive NR Byte (RNR[7:0]) - These eight bits are the integrated version of the NR byte as extracted from the E3 frame. 307 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: E3G832.RFECR E3 G.832 Receive Framing Error Count Register (1,3,5,7)34h Bit # Name Default 15 FE15 0 14 FE14 0 13 FE13 0 12 FE12 0 11 FE11 0 10 FE10 0 9 FE9 0 8 FE8 0 Bit # Name Default 7 FE7 0 6 FE6 0 5 FE5 0 4 FE4 0 3 FE3 0 2 FE2 0 1 FE1 0 0 FE0 0 Bits 15 to 0: Framing Error Count (FE[15:0]) - These 16 bits indicate the number of framing error events on the incoming E3 data stream. This register is updated via the PMU signal (see Section 10.4.5). Register Name: Register Description: Register Address: E3G832.RPECR E3 G.832 Receive Parity Error Count Register (1,3,5,7)36h Bit # Name Default 15 PE15 0 14 PE14 0 13 PE13 0 12 PE12 0 11 PE11 0 10 PE10 0 9 PE9 0 8 PE8 0 Bit # Name Default 7 PE7 0 6 PE6 0 5 PE5 0 4 PE4 0 3 PE3 0 2 PE2 0 1 PE1 0 0 PE0 0 Bits 15 to 0: Parity Error Count (PE[15:0]) - These 16 bits indicate the number of parity (BIP-8) errors detected on the incoming E3 data stream. This register is updated via the PMU signal (see Section 10.4.5). Register Name: Register Description: Register Address: E3G832.RFBER E3 G.832 Receive Remote Error Indication Count Register (1,3,5,7)38h Bit # Name Default 15 FBE15 0 14 FBE14 0 13 FBE13 0 12 FBE12 0 11 FBE11 0 10 FBE10 0 9 FBE9 0 8 FBE8 0 Bit # Name Default 7 FBE7 0 6 FBE6 0 5 FBE5 0 4 FBE4 0 3 FBE3 0 2 FBE2 0 1 FBE1 0 0 FBE0 0 Bits 15 to 0: Remote Error Indication Count (FBE[15:0]) - These 16 bits indicate the number of remote error indications detected on the incoming E3 data stream. This register is updated via the PMU signal (see Section 10.4.5). 308 DS3181/DS3182/DS3183/DS3184 12.10.7 Transmit Clear Channel The transmit clear-channel mode uses one register. 12.10.7.1 Register Map Table 12-39. Transmit Clear-Channel Register Map ADDRESS (1,3,5,7)18h (1,3,5,7)1Ah (1,3,5,7)1Ch (1,3,5,7)1Eh REGISTER CC.TCR -- -- -- REGISTER DESCRIPTION Clear-Channel Transmit Control Register Reserved Reserved Reserved 12.10.7.2 Register Bit Descriptions Register Name: Register Description: Register Address: Bit # Name Default 15 Reserved 0 CC.TCR Clear-Channel Transmit Control Register (1,3,5,7)18h 14 -- 0 13 -- 0 12 Reserved 0 11 Reserved 0 10 Reserved 0 9 Reserved 0 8 Reserved 0 Bit # 7 6 5 4 3 2 1 0 Name -- -- Reserved Reserved Reserved Reserved Reserved TAIS Default 0 0 0 0 0 0 0 0 Bit 0: Transmit Alarm Indication Signal (TAIS) - When 0, the normal signal is transmitted. When 1, the output clear-channel data stream is forced to all ones (AIS). Note: This bit is logically ORed with the TAIS input signal. 309 DS3181/DS3182/DS3183/DS3184 12.10.8 Receive Clear Channel The receive clear-channel mode uses four registers. 12.10.8.1 Register Map Table 12-40. Receive Clear-Channel Register Map ADDRESS (1,3,5,7)20h (1,3,5,7)22h (1,3,5,7)24h (1,3,5,7)26h (1,3,5,7)28h (1,3,5,7)2Ah (1,3,5,7)2Ch (1,3,5,7)2Eh (1,3,5,7)30h (1,3,5,7)32h (1,3,5,7)34h (1,3,5,7)36h (1,3,5,7)38h (1,3,5,7)3Ah (1,3,5,7)3Ch (1,3,5,7)3Eh REGISTER CC.RCR -- CC.RSR1 -- CC.RSRL1 -- CC.RSRIE1 -- -- -- -- -- -- -- -- -- REGISTER DESCRIPTION Clear-Channel Receive Control Register Reserved Clear-Channel Receive Status Register 1 Reserved Clear-Channel Receive Status Register Latched 1 Reserved Clear-Channel Receive Status Register Interrupt Enable 1 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Unused Unused 12.10.8.2 Register Bit Descriptions Register Name: Register Description: Register Address: CC.RCR Clear-Channel Receive Control Register (1,3,5,7)20h Bit # Name Default 15 Reserved 0 14 Reserved 0 13 Reserved 0 12 MDAISI 0 11 AAISD 0 10 Reserved 0 9 Reserved 0 8 Reserved 0 Bit # Name Default 7 Reserved 0 6 Reserved 0 5 Reserved 0 4 Reserved 0 3 Reserved 0 2 Reserved 0 1 Reserved 0 0 Reserved 0 Bit 12: Manual Downstream AIS Insertion (MDAISI) - When 0, manual downstream AIS insertion is disabled. When 1, manual downstream AIS insertion is enabled. Bit 11: Automatic Downstream AIS Disable (AAISD) - When 0, the presence of a LOS condition will cause downstream AIS to be inserted. When 1, the presence of a LOS condition will not cause downstream AIS to be inserted. 310 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: CC.RSR1 Clear-Channel Receive Status Register 1 (1,3,5,7)24h Bit # Name Default 15 Reserved 0 14 Reserved 0 13 -- 0 12 Reserved 0 11 Reserved 0 10 Reserved 0 9 Reserved 0 8 RUA1 0 Bit # Name Default 7 Reserved 0 6 Reserved 0 5 -- 0 4 Reserved 0 3 Reserved 0 2 Reserved 0 1 Reserved 0 0 LOS 0 Bit 8: Receive Unframed All 1's (RUA1) - When 0, the receive frame processor is not in a receive unframed all 1's (RUA1) condition. When 1, the receive frame processor is in an RUA1 condition. Bit 0: Loss Of Signal (LOS) - When 0, the receive loss of signal (LOS) input (RLOS) is low. When 1, RLOS is high. Register Name: Register Description: Register Address: CC.RSRL1 Clear-Channel Receive Status Register Latched 1 (1,3,5,7)28h Bit # Name Default 15 Reserved 0 14 Reserved 0 13 Reserved 0 12 Reserved 0 11 Reserved 0 10 Reserved 0 9 Reserved 0 8 RUA1L 0 Bit # Name Default 7 Reserved 0 6 Reserved 0 5 Reserved 0 4 Reserved 0 3 Reserved 0 2 Reserved 0 1 Reserved 0 0 LOSL 0 Bit 8: Receive Unframed All 1's Latched (RUA1L) - This bit is set when the RUA1 bit changes state. Bit 0: Loss Of Signal Change Latched (LOSL) - This bit is set when the LOS bit changes state. Register Name: Register Description: Register Address: CC.RSRIE1 Clear-Channel Receive Status Register Interrupt Enable 1 (1,3,5,7)2Ch Bit # Name Default 15 Reserved 0 14 Reserved 0 13 Reserved 0 12 Reserved 0 11 Reserved 0 10 Reserved 0 9 Reserved 0 8 RUA1IE 0 Bit # Name Default 7 Reserved 0 6 Reserved 0 5 Reserved 0 4 Reserved 0 3 Reserved 0 2 Reserved 0 1 Reserved 0 0 LOSIE 0 Bit 8: Receive Unframed All 1's Interrupt Enable (RUA1IE) - This bit enables an interrupt if the RUA1L bit is set. 0 = interrupt disabled 1 = interrupt enabled Bit 0: Loss Of Signal Interrupt Enable (LOSIE) - This bit enables an interrupt if the LOSL bit is set. 0 = interrupt disabled 1 = interrupt enabled 311 DS3181/DS3182/DS3183/DS3184 12.11 Fractional DS3/E3 12.11.1 Fractional Transmit Side Register Map The transmit side uses three registers. Table 12-41. Fractional Transmit Side Register Map ADDRESS REGISTER (1,3,5,7)40h (1,3,5,7)42h (1,3,5,7)44h (1,3,5,7)46h FRAC.TCR FRAC.TDGSR FRAC.TSASR -- REGISTER DESCRIPTION Fractional Transmit Control Register Fractional Transmit Data Group Size Register Fractional Transmit Section A Size Register Unused 12.11.1.1 Register Bit Descriptions Register Name: Register Description: Register Address: FRAC.TCR Fractional Transmit Control Register (1,3,5,7)40h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 -- 0 3 -- 0 2 TFOSC1 0 1 TFOSC0 0 0 TSASS 0 Bits 2 to 1: Transmit Fractional Overhead Source Control (TFOSC[1:0]) - These two bits control the source of the transmit fractional overhead. 00 = all zeros. 01 = all ones. 10 = 1010 pattern. 11 = external (TFOH). Bit 0: Transmit Section A Source Select (TSASS) 0 = Section A contains fractional overhead 1 = Section A contains payload data 312 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: FRAC.TDGSR Fractional Transmit Data Group Size Register (1,3,5,7)42h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 TDGS12 0 11 TDGS11 0 10 TDGS10 0 9 TDGS9 0 8 TDGS8 0 Bit # Name Default 7 TDGS7 0 6 TDGS6 0 5 TDGS5 0 4 TDGS4 0 3 TDGS3 0 2 TDGS2 0 1 TDGS1 0 0 TDGS0 0 Bits 12 to 0: Transmit Data Group Size (TDGS[12:0]) - These 13 bits indicate the number of bits contained within each transmit data group. A values of 0000h and 0001h both result in a transmit data group size of one bit. Register Name: Register Description: Register Address: FRAC.TSASR Fractional Transmit Section A Size Register (1,3,5,7)44h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 TSAS12 0 11 TSAS11 0 10 TSAS10 0 9 TSAS9 0 8 TSAS8 0 Bit # Name Default 7 TSAS7 0 6 TSAS6 0 5 TSAS5 0 4 TSAS4 0 3 TSAS3 0 2 TSAS2 0 1 TSAS1 0 0 TSAS0 0 Bits 15 to 0: Transmit Section A Size (TSAS[12:0]) - These 13 bits indicate the number of bits contained within Section A of each transmit data group. If TSAS[12:0] is equal to or greater than the data group size (TDGSR.TDGS[12:0]), only "Section A" data will be transmitted. 313 DS3181/DS3182/DS3183/DS3184 12.11.2 Fractional Receive Side Register Map The receive side uses three registers. Table 12-42. Receive Side Register Map ADDRESS REGISTER (1,3,5,7)48h (1,3,5,7)4Ah (1,3,5,7)4Ch (1,3,5,7)4Eh FRAC.RCR FRAC.RDGSR FRAC.RSASR -- REGISTER DESCRIPTION Fractional Receive Control Register Fractional Receive Data Group Size Register Fractional Receive Section A Size Register Unused 12.11.2.1 Register Bit Descriptions Register Name: Register Description: Register Address: FRAC.RCR Fractional Receive Control Register (1,3,5,7)48h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 -- 0 3 -- 0 2 -- 0 1 -- 0 0 RSASS 0 Bit 0: Receive Section A Source Select (RSASS) - When 0, Section A of each receive data group will contain fractional overhead. When 1, Section A of each receive data group will contain payload data. Register Name: Register Description: Register Address: FRAC.RDGSR Fractional Receive Data Group Size Register (1,3,5,7)4Ah Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 RDGS12 0 11 RDGS11 0 10 RDGS10 0 9 RDGS9 0 8 RDGS8 0 Bit # Name Default 7 RDGS7 0 6 RDGS6 0 5 RDGS5 0 4 RDGS4 0 3 RDGS3 0 2 RDGS2 0 1 RDGS1 0 0 RDGS0 0 Bits 12 to 0: Receive Data Group Size (RDGS[12:0]) - These 13 bits indicate the number of bits contained within each receive data group. A values of 0000h and 0001h both result in a receive data group size of one bit. 314 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: FRAC.RSASR Fractional Receive Section A Size Register (1,3,5,7)4Ch Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 RSAS12 0 11 RSAS11 0 10 RSAS10 0 9 RSAS9 0 8 RSAS8 0 Bit # Name Default 7 RSAS7 0 6 RSAS6 0 5 RSAS5 0 4 RSAS4 0 3 RSAS3 0 2 RSAS2 0 1 RSAS1 0 0 RSAS0 0 Bits 12 to 0: Receive Section A Size (RSAS[12:0]) - These 13 bits indicate the number of bits contained within Section A of each receive data group. If RSAS[12:0] is equal to or greater than the data group size (FRAC.RDGSR.RDGS[12:0]), all data will be marked as "Section A" data. 315 DS3181/DS3182/DS3183/DS3184 12.12 DS3/E3 PLCP 12.12.1 Transmit Side PLCP The transmit side uses seven registers. 12.12.1.1 Register Map Table 12-43. Transmit Side PLCP Register Map ADDRESS REGISTER (1,3,5,7)50h (1,3,5,7)52h (1,3,5,7)54h (1,3,5,7)56h (1,3,5,7)58h (1,3,5,7)5Ah (1,3,5,7)5Ch (1,3,5,7)5Eh PLCP.TCR PLCP.TEIR PLCP.TFGBR PLCP.TM12BR PLCP.TZ12BR PLCP.TZ34BR PLCP.TZ56BR -- REGISTER DESCRIPTION PLCP Transmit Control Register PLCP Transmit Error Insertion Register PLCP Transmit F1 and G1 Byte Register PLCP Transmit M1 and M2 Byte Register PLCP Transmit Z1 and Z2 Byte Register PLCP Transmit Z3 and Z4 Byte Register PLCP Transmit Z5 and Z6 Byte Register Unused 12.12.1.2 Register Bit Descriptions Register Name: Register Description: Register Address: PLCP.TCR PLCP Transmit Control Register (1,3,5,7)50h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 TMC1 0 3 TMC0 0 2 TF1C1 0 1 TF1C0 0 0 AREID 0 Bits 4 to 3: Transmit M2 and M1 Byte Control (TMC[1:0]) - These two bits control the source of the transmit M2 and M1 bytes. 00 = concatenated M1 and M2 (128 kHz) from transmit HDLC controller. 01 = M2 (64kHz) from transmit HDLC controller; M1 from M1 byte register (PLCP.TM12BR). 10 = M2 from M2 byte register; M1 (64 kHz) from transmit HDLC controller. 11 = M2 from M2 byte register; M1 from M1 byte register Bits 2 to 1: Transmit F1 Byte Control (TF1C[1:0]) - These two bits control the source of the transmit F1 byte. 00 = transmit Trail Trace controller. 01 = transmit HDLC controller. 10 = F1 byte register (PLCP.TFGBR). 11 = reserved Note: If TMC[1:0] is 00 and TF1C[1:0] is 01, the F1 byte will be invalid. If TMC[1:0] is 01 and TF1C[1:0] is 01, both M2 and F1 will carry the transmit HDLC data link. If TMC[1:0] is 10 and TF1C[1:0] is 01, both M1 and F1 will carry the transmit HDLC data link. When F1 and M# both carry the transmit HDLC data link, the F1 byte and M# byte in the same frame may or may not be equal. Bit 0: Automatic REI Defeat (AREID) - When 0, the REI is automatically generated based upon the parity (BIP-8) errors detected in the receive PLCP Frame Processor. When 1, the REI is inserted from the G1 register bits TREI[3:0]. 316 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PLCP.TEIR PLCP Transmit Error Insertion Register (1,3,5,7)52h Bit # Name Default 15 -- 0 14 -- 0 13 REIME 0 12 CREIIE 0 11 REIEI 0 10 PBEE 0 9 CPEIE 0 8 PEI 0 Bit # Name Default 7 -- 0 6 -- 0 5 FEE 0 4 FEIC1 0 3 FEIC0 0 2 FEI 0 1 TSEI 0 0 MEIMS 0 Bit 13: Remote Error Indication Maximum Error (REIME) - When 0, an REI error is generated by inserting a value of 1h (single error) into the REI bits (G1[1:4]). When 1, an REI error is generated by inserting a value of 8h (eight errors) into the REI bits. Bit 12: Continuous Remote Error Indication Error Insertion Enable (CREIIE) - When 0, single remote error indication (REI) error insertion is enabled. When 1, continuous REI error insertion is enabled, and REI errors will be continuously transmitted if REIEI is high. Bit 11: Remote Error Indication Error Insertion Enable (REIEI) - When 0, REI error insertion is disabled. When 1, REI error insertion is enabled. Bit 10: Parity Block Error Enable (PBEE) - When 0, a parity error is generated by inverting a single bit in the B1 byte. When 1, a parity error is generated by inverting all eight bits in the B1 byte. Bit 9: Continuous Parity Error Insertion Enable (CPEIE) - When 0, single parity (BIP-8) error insertion is enabled. When 1, continuous parity error insertion is enabled, and parity errors will be transmitted continuously if PEI is high. Bit 8: Parity Error Insertion Enable (PEI) - When 0, parity (BIP-8) error insertion is disabled. When 1, parity (BIP8) error insertion is enabled. Bit 5: Framing Byte Error Enable (FEE) - When 0, a framing bit error is generated by inverting a single bit in the indicated byte. When 1, a framing byte error is generated by inverting all eight bits of the indicated byte. Bits 4 to 3: Framing Error Control (FEIC[1:0]) - These two bits control the type of framing error event to be inserted. 00 = single A1 or A2 error (1 per sub-frame maximum). 01 = single POI (P#) error (1 per 2 sub-frames maximum). 10 = both an A1 and an A2 error in the same sub-frame. 11 = two POI (P#) errors in consecutive sub-frames. Bit 2: Framing Error Insertion Enable (FEI) - When 0, framing error insertion is disabled. When 1, framing error insertion is enabled. Bit 1: Transmit Single Error Insert (TSEI) - This bit causes an error of the enabled type(s) to be inserted in the transmit data stream if manual error insertion is disabled (MEIMS = 0). A 0 to 1 transition causes a single error to be inserted. For a second error to be inserted, this bit must be set to 0, and back to 1. Note: If MEIMS is low, and this bit transitions more than once between error insertion opportunities, only one error will be inserted. Bit 0: Manual Error Insert Mode Select (MEIMS) - When 0, error insertion is initiated by the TSEI register bit. When 1, error insertion is initiated by the transmit manual error insertion signal (TMEI). Note: If TMEI or TSEI is one, changing the state of this bit may cause an error to be inserted. 317 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PLCP.TFGBR PLCP Transmit F1 and G1 Byte Register (1,3,5,7)54h Bit # Name Default 15 TF17 0 14 TF16 0 13 TF15 0 12 TF14 0 11 TF13 0 Bit # Name Default 7 TREI3 0 6 TREI2 0 5 TREI1 0 4 TREI0 0 3 TRAI 0 10 TF12 0 2 TLSS2 0 9 TF11 0 8 TF10 0 1 TLSS1 0 0 TLSS0 0 Bits 15 to 8: Transmit F1 Byte (TF1[7:0]) - These eight bits are the F1 byte to be inserted into the transmit PLCP frame. Bits 7 to 4: Transmit REI Setting (TREI[3:0]) - When automatic REI generation is defeated (PLCP.TCR.AREID = 0), these bits are inserted into the REI bits (G1[1:4]). Bit 3: Transmit RAI Setting (TRAI) -This bit is inserted into the RAI bits (G1[5]). Bits 2 to 0: Transmit Link Status Signal (TLSS[2:0]) - These three bits are the transmit link status signal (G1[6:8]) to be inserted into the transmit PLCP frame. Register Name: Register Description: Register Address: PLCP.TM12BR PLCP Transmit M1 and M2 Byte Register (1,3,5,7)56h Bit # Name Default 15 TM27 0 14 TM26 0 13 TM25 0 12 TM24 0 11 TM23 0 10 TM22 0 9 TM21 0 8 TM20 0 Bit # Name Default 7 TM17 0 6 TM16 0 5 TM15 0 4 TM14 0 3 TM13 0 2 TM12 0 1 TM11 0 0 TM10 0 Bits 15 to 8: Transmit M2 Byte (TM2[7:0]) - These eight bits are the M2 byte to be inserted into the transmit PLCP frame. Bits 7 to 0: Transmit M1 Byte (TM1[7:0]) - These eight bits are the M1 byte to be inserted into the transmit PLCP frame. 318 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PLCP.TZ12BR PLCP Transmit Z1 and Z2 Byte Register (1,3,5,7)58h Bit # Name Default 15 TZ27 0 14 TZ26 0 13 TZ25 0 12 TZ24 0 11 TZ23 0 10 TZ22 0 9 TZ21 0 8 TZ20 0 Bit # Name Default 7 TZ17 0 6 TZ16 0 5 TZ15 0 4 TZ14 0 3 TZ13 0 2 TZ12 0 1 TZ11 0 0 TZ10 0 Bits 15 to 8: Transmit Z2 Byte (TZ2[7:0]) - These eight bits are the Z2 byte to be inserted into the transmit PLCP frame. Bits 7 to 0: Transmit Z1 Byte (TZ1[7:0]) - These eight bits are the Z1 byte to be inserted into the transmit PLCP frame. Register Name: Register Description: Register Address: PLCP.TZ34BR PLCP Transmit Z3 and Z4 Byte Register (1,3,5,7)5Ah Bit # Name Default 15 TZ47 0 14 TZ46 0 13 TZ45 0 12 TZ44 0 11 TZ43 0 10 TZ42 0 9 TZ41 0 8 TZ40 0 Bit # Name Default 7 TZ37 0 6 TZ36 0 5 TZ35 0 4 TZ34 0 3 TZ33 0 2 TZ32 0 1 TZ31 0 0 TZ30 0 Bits 15 to 8: Transmit Z4 Byte (TZ4[7:0]) - These eight bits are the Z4 byte to be inserted into the transmit PLCP frame (This bits are unused in E3 mode). Bits 7 to 0: Transmit Z3 Byte (TZ3[7:0]) - These eight bits are the Z3 byte to be inserted into the transmit PLCP frame. Register Name: Register Description: Register Address: PLCP.TZ56BR PLCP Transmit Z5 and Z6 Byte Register (1,3,5,7)5Ch Bit # Name Default 15 TZ67 0 14 TZ66 0 13 TZ65 0 12 TZ64 0 11 TZ63 0 10 TZ62 0 9 TZ61 0 8 TZ60 0 Bit # Name Default 7 TZ57 0 6 TZ56 0 5 TZ55 0 4 TZ54 0 3 TZ53 0 2 TZ52 0 1 TZ51 0 0 TZ50 0 Bits 15 to 8: Transmit Z6 Byte (TZ6[7:0]) - These eight bits are the Z6 byte to be inserted into the transmit PLCP frame (This bits are unused in E3 mode). Bits 7 to 0: Transmit Z5 Byte (TZ5[7:0]) - These eight bits are the Z5 byte to be inserted into the transmit PLCP frame (This bits are unused in E3 mode). 319 DS3181/DS3182/DS3183/DS3184 12.12.2 Receive Side PLCP Register Map The receive side uses 13 registers. Table 12-44. Receive Side PLCP Register Map ADDRESS REGISTER REGISTER DESCRIPTION (1,3,5,7)60h (1,3,5,7)62h (1,3,5,7)64h (1,3,5,7)66h (1,3,5,7)68h (1,3,5,7)6Ah (1,3,5,7)6Ch (1,3,5,7)6Eh (1,3,5,7)70h (1,3,5,7)72h (1,3,5,7)74h (1,3,5,7)76h (1,3,5,7)78h (1,3,5,7)7Ah (1,3,5,7)7Ch (1,3,5,7)7Eh PLCP.RCR -- PLCP.RSR1 PLCP.RSR2 PLCP.RSRL1 PLCP.RSRL2 PLCP.RSRIE1 PLCP.RSRIE2 PLCP.RFECR PLCP.RPECR PLCP.RREICR PLCP.RFGBR PLCP.RM12BR PLCP.RZ12BR PLCP.RZ34BR PLCP.RZ56BR PLCP Receive Control Register Unused PLCP Receive Status Register 1 PLCP Receive Status Register 2 PLCP Receive Status Register Latched 1 PLCP Receive Status Register Latched 2 PLCP Receive Status Register Interrupt Enable 1 PLCP Receive Status Register Interrupt Enable 2 PLCP Receive Framing Error Count Register PLCP Receive P-Bit Parity Error Count Register PLCP Receive Remote Error Indication Count Register PLCP Receive F1 and G1 Byte Register PLCP Receive M1 and M2 Byte Register PLCP Receive Z1 and Z2 Byte Register PLCP Receive Z3 and Z4 Byte Register PLCP Receive Z5 and Z6 Byte Register 12.12.2.1 Register Bit Descriptions Register Name: Register Description: Register Address: PLCP.RCR PLCP Receive Control Register (1,3,5,7)60h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 RHSC1 0 8 RHSC0 0 Bit # Name Default 7 -- 0 6 RLIE 0 5 -- 0 4 PECC 0 3 FEPD 0 2 FECC 0 1 ECC 0 0 FRSYNC 0 Bits 9 to 8: Receive HDLC Source Control (RHSC[1:0]) - These two bits control the source of the receive HDLC controller. 00 = F1 byte. 01 = M1 byte. 10 = M2 byte. 11 = M2 and M1 byte. Bit 6: Receive LOF Integration Enable (RLIE) - When 0, the receive Loss Of Frame (LOF) integration counter is disabled. When 1, the receive LOF integration counter is enabled. Bit 4: Parity Error Count Control (PECC) - When 0, BIP-8 (B1 byte) bit errors are detected (up to 8 per frame). When 1, BIP-8 block errors are detected (no more than one per frame). Note: The transmit REI bits are affected by the setting of this bit as the REI bits reflect the number of BIP-8 errors detected/counted. Bit 3: Framing Error POI Disable (FEPD) - When 0, Path Overhead Indicator (POI) byte (P#) and framing alignment byte (A1 & A2) errors are detected. When 1, only A1 & A2 errors are detected. Note: This bit is ignored when OOF events are counted (FECC=1) Bit 2: Framing Error Count Control (FECC) - This bit controls the type of framing error events that are counted. When 0, A1 byte errors, A2 byte errors, and P# byte errors (up to 3 per sub-frame) are counted. When 1, OOF events are counted. 320 DS3181/DS3182/DS3183/DS3184 Bit 1: Error Count Control (ECC) - When 0, framing errors, BIP-8 parity errors, and REI errors will not be counted during an OOF condition (BIP-8 parity error counting will resume in the second full frame after an OOF condition is cleared). When 1, framing errors, BIP-8 parity errors, and REI errors will be counted during an OOF condition. Bit 0: Force Framer Re-synchronization (FRSYNC) - A 0 to 1 transition forces the framer into the "Search state. Once the framer acquires lock, the data path frame counters will be updated regardless of whether an OOF condition exists or not. The bit must be cleared and set to one again to force another re-synchronization Register Name: Register Description: Register Address: PLCP.RSR1 PLCP Receive Status Register 1 (1,3,5,7)64h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 LOF Bit # Name 7 -- 6 -- 5 REIC 4 PEC 3 FEC 2 RAI 1 -- 0 OOF Bit 8: Loss Of Frame (LOF) - When 0, the receive line interface is not in a loss of frame (LOF) condition. When 1, the receive line interface is in an LOF condition. Bit 5: Remote Error Indication Count (REIC) - When 0, the remote error indication count is zero. When 1, the remote error indication count is one or more. Bit 4: Parity Error Count (PEC) - When 0, the parity error count is zero. When 1, the parity error count is one or more. Bit 3: Framing Error Count (FEC) - When 0, the framing error count is zero. When 1, the framing error count is one or more. Bit 2: Remote Alarm Indication (RAI) - This bit indicates the current state of the remote alarm indication (RAI), which is the fifth bit of the G1 byte (G1[5]). Bit 0: Out Of Frame (OOF) - When 0, the receive frame processor is not in an out of frame (OOF) condition. When 1, the receive frame processor is in an OOF condition. Register Name: Register Description: Register Address: PLCP.RSR2 PLCP Receive Status Register 2 (1,3,5,7)66h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 -- 6 -- 5 -- 4 -- 3 -- 2 -- 1 -- 0 LSSU Bit 0: Receive Link Status Signal Unstable (LSSU) - When 0, the receive link states signal is stable. When 1, the receive link states signal is unstable. 321 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PLCP.RSRL1 PLCP Receive Status Register Latched 1 (1,3,5,7)68h Bit # Name 15 -- 14 -- 13 REIL 12 PEL 11 FEL 10 -- 9 -- 8 LOFL Bit # Name 7 -- 6 -- 5 REICL 4 PECL 3 FECL 2 RAIL 1 COFAL 0 OOFL Bit 13: Remote Error Indication Latched (REIL) - This bit is set when a far-end block error is detected. Bit 12: Parity Error Latched (PEL) - This bit is set when a BIP-8 parity error is detected. Bit 11: Framing Error Latched (FEL) - This bit is set when a framing error is detected. Bit 8: Loss Of Frame Change Latched (LOFL) - This bit is set when the LOF bit changes state. Bit 5: Remote Error Indication Count Latched (REICL) - This bit is set when the REIC bit transitions from zero to one. Bit 4: Parity Error Count Latched (PECL) - This bit is set when the PEC bit transitions from zero to one. Bit 3: Framing Error Count Latched (FECL) - This bit is set when the FEC bit transitions from zero to one. Bit 2: Remote Defect Indication Change Latched (RAIL) - This bit is set when the RAI bit changes state. Bit 1: Change Of Frame Alignment Latched (COFAL) - This bit is set when the data path frame counters are updated with a new frame alignment that is different from the previous frame alignment. Bit 0: Out Of Frame Change Latched (OOFL) - This bit is set when the OOF bit changes state. 322 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PLCP.RSRL2 PLCP Receive Status Register Latched 2 (1,3,5,7)6Ah Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 RZ6L Bit # Name 7 RZ3L 6 RZ2L 5 RZ1L 4 RM2L 3 RM1L 2 RF1L 9 RZ5L 8 RZ4L 1 LSSL 0 LSSUL Bit 10: Receive Z6 Byte Change Latched (RZ6L) - This bit is set when the RZ6[7:0] bits change state (This bit is zero in E3 mode). Bit 9: Receive Z5 Byte Change Latched (RZ5L) - This bit is set when the RZ5[7:0] bits change state (This bit is zero in E3 mode). Bit 8: Receive Z4 Byte Change Latched (RZ4L) - This bit is set when the RZ4[7:0] bits change state (This bit is zero in E3 mode). Bit 7: Receive Z3 Byte Change Latched (RZ3L) - This bit is set when the RZ3[7:0] bits change state. Bit 6: Receive Z2 Byte Change Latched (RZ2L) - This bit is set when the RZ2[7:0] bits change state. Bit 5: Receive Z1 Byte Change Latched (RZ1L) - This bit is set when the RZ1[7:0] bits change state. Bit 4: Receive M2 Byte Change Latched (RM2L) - This bit is set when the RM2[7:0] bits change state. Bit 3: Receive M1 Byte Change Latched (RM1L) - This bit is set when the RM1[7:0] bits change state. Bit 2: Receive F1 Byte Change Latched (RF1L) - This bit is set when the RF1[7:0] bits change state. Bit 1: Receive Link Status Signal Change Latched (LSSL) - This bit is set when the LSS[2:0] bits change state. Bit 0: Receive Link Status Signal Unstable Change Latched (LSSUL) - This bit is set when the LSSU bit changes state. 323 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PLCP.RSRIE1 PLCP Receive Status Register Interrupt Enable 1 (1,3,5,7)6Ch Bit # Name Default 15 -- 0 14 -- 0 13 REIIE 0 12 PEIE 0 11 FEIE 0 10 -- 0 9 -- 0 8 LOFIE 0 Bit # Name Default 7 -- 0 6 -- 0 5 REICIE 0 4 PECIE 0 3 FECIE 0 2 RAIIE 0 1 COFAIE 0 0 OOFIE 0 Bit 13: Remote Error Indication Interrupt Enable (REIIE) - This bit enables an interrupt if the REIL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 12: Parity Error Interrupt Enable (PEIE) - This bit enables an interrupt if the PEL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 11: Framing Error Interrupt Enable (FEIE) - This bit enables an interrupt if the FEL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 8: Loss Of Frame Interrupt Enable (LOFIE) - This bit enables an interrupt if the LOFL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 5: Remote Error Indication Count Interrupt Enable (REICIE) - This bit enables an interrupt if the REICL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 4: Parity Error Count Interrupt Enable (PECIE) - This bit enables an interrupt if the PECL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 3: Framing Error Count Interrupt Enable (FECIE) - This bit enables an interrupt if the FECL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 2: Remote Defect Indication Interrupt Enable (RAIIE) - This bit enables an interrupt if the RAIL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 1: Change Of Frame Alignment Interrupt Enable (COFAIE) - This bit enables an interrupt if the COFAL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled 324 DS3181/DS3182/DS3183/DS3184 Bit 0: Out Of Frame Interrupt Enable (OOFIE) - This bit enables an interrupt if the OOFL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled 325 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PLCP.RSRIE2 PLCP Receive Status Register Interrupt Enable 2 (1,3,5,7)6Eh Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 RZ6IE 0 Bit # Name Default 7 RZ3IE 0 6 RZ2IE 0 5 RZ1IE 0 4 RM2IE 0 3 RM1IE 0 2 RF1IE 0 9 RZ5IE 0 1 LSSIE 0 8 RZ4IE 0 0 LSSUIE 0 Bit 10: Receive Z6 Byte Interrupt Enable (RZ6IE) - This bit enables an interrupt if the RZ6L bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. (This bit is unused in E3 mode). 0 = interrupt disabled 1 = interrupt enabled Bit 9: Receive Z5 Byte Interrupt Enable (RZ5IE) - This bit enables an interrupt if the RZ5L bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. (This bit is unused in E3 mode). 0 = interrupt disabled 1 = interrupt enabled Bit 8: Receive Z4 Byte Interrupt Enable (RZ4IE) - This bit enables an interrupt if the RZ4L bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. (This bit is unused in E3 mode). 0 = interrupt disabled 1 = interrupt enabled Bit 7: Receive Z3 Byte Interrupt Enable (RZ3IE) - This bit enables an interrupt if the RZ3L bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 6: Receive Z2 Byte Interrupt Enable (RZ2IE) - This bit enables an interrupt if the RZ2L bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 5: Receive Z1 Byte Interrupt Enable (RZ1IE) - This bit enables an interrupt if the RZ1L bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 4: Receive M2 Byte Interrupt Enable (RM2IE) - This bit enables an interrupt if the RM2L bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 3: Receive M1 Byte Interrupt Enable (RM1IE) - This bit enables an interrupt if the RM1L bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 2: Receive F1 Byte Interrupt Enable (RF1IE) - This bit enables an interrupt if the RF1L bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled 326 DS3181/DS3182/DS3183/DS3184 Bit 1: Receive Link Status Signal Interrupt Enable (LSSIE) - This bit enables an interrupt if the LSSL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 0: Receive Link Status Signal Unstable Interrupt Enable (LSSUIE) - This bit enables an interrupt if the LSSUL bit is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled 327 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PLCP.RFECR PLCP Receive Framing Error Count Register (1,3,5,7)70h Bit # Name Default 15 FE15 0 14 FE14 0 13 FE13 0 12 FE12 0 11 FE11 0 10 FE10 0 9 FE9 0 8 FE8 0 Bit # Name Default 7 FE7 0 6 FE6 0 5 FE5 0 4 FE4 0 3 FE3 0 2 FE2 0 1 FE1 0 0 FE0 0 Bits 15 to 0: Framing Error Count (FE[15:0]) - These 16 bits indicate the number of framing error events on the incoming PLCP data stream. This register is updated via the PMU signal (see Section 10.4.5). Register Name: Register Description: Register Address: PLCP.RPECR PLCP Receive P-Bit Parity Error Count Register (1,3,5,7)72h Bit # Name Default 15 PE15 0 14 PE14 0 13 PE13 0 12 PE12 0 11 PE11 0 10 PE10 0 9 PE9 0 8 PE8 0 Bit # Name Default 7 PE7 0 6 PE6 0 5 PE5 0 4 PE4 0 3 PE3 0 2 PE2 0 1 PE1 0 0 PE0 0 Bits 15 to 0: Parity Error Count (PE[15:0]) - These 16 bits indicate the number of parity (BIP-8) errors detected on the incoming PLCP data stream. This register is updated via the PMU signal (see Section 10.4.5). Register Name: Register Description: Register Address: PLCP.RREICR PLCP Receive Remote Error Indication Count Register (1,3,5,7)74h Bit # Name Default 15 REI15 0 14 REI14 0 13 REI13 0 12 REI12 0 11 REI11 0 10 REI10 0 9 REI9 0 8 REI8 0 Bit # Name Default 7 REI7 0 6 REI6 0 5 REI5 0 4 REI4 0 3 REI3 0 2 REI2 0 1 REI1 0 0 REI0 0 Bits 15 to 0: Remote Error Indication Count (REI[15:0]) - These 16 bits indicate the number of remote error indication errors detected on the incoming PLCP data stream. This register is updated via the PMU signal (see Section 10.4.5). 328 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PLCP.RFGBR PLCP Receive F1 and G1 Byte Register (1,3,5,7)76h Bit # Name Default 15 RF17 0 14 RF16 0 13 RF15 0 12 RF14 0 11 RF13 0 10 RF12 0 9 RF11 0 8 RF10 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 -- 0 3 -- 0 2 LSS2 0 1 LSS1 0 0 LSS0 0 Bits 15 to 8: Receive F1 Byte (RF1[7:0]) - These eight bits are the integrated version of the F1 byte as extracted from the receive PLCP frame. Bits 2 to 0: Receive Link Status Signal (LSS[2:0]) - These three bits are the integrated version of the receive link status signal (G1[6:8]) as extracted from the receive PLCP frame. Register Name: Register Description: Register Address: PLCP.RM12BR PLCP Receive M1 and M2 Byte Register (1,3,5,7)78h Bit # Name Default 15 RM27 0 14 RM26 0 13 RM25 0 12 RM24 0 11 RM23 0 10 RM22 0 9 RM21 0 8 RM20 0 Bit # Name Default 7 RM17 0 6 RM16 0 5 RM15 0 4 RM14 0 3 RM13 0 2 RM12 0 1 RM11 0 0 RM10 0 Bits 15 to 8: Receive M2 Byte (RM2[7:0]) - These eight bits are the integrated version of the M2 byte as extracted from the receive PLCP frame. Bits 7 to 0: Receive M1 Byte (RM1[7:0]) - These eight bits are the integrated version of the M1 byte as extracted from the receive PLCP frame. Register Name: Register Description: Register Address: PLCP.RZ12BR PLCP Receive Z1 and Z2 Byte Register (1,3,5,7)7Ah Bit # Name Default 15 RZ27 0 14 RZ26 0 13 RZ25 0 12 RZ24 0 11 RZ23 0 10 RZ22 0 9 RZ21 0 8 RZ20 0 Bit # Name Default 7 RZ17 0 6 RZ16 0 5 RZ15 0 4 RZ14 0 3 RZ13 0 2 RZ12 0 1 RZ11 0 0 RZ10 0 Bits 15 to 8: Receive Z2 Byte (RZ2[7:0]) - These eight bits are the integrated version of the Z2 byte as extracted from the receive PLCP frame. Bits 7 to 0: Receive Z1 Byte (RZ1[7:0]) - These eight bits are the integrated version of the Z1 byte as extracted from the receive PLCP frame. 329 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PLCP.RZ34BR PLCP Receive Z3 and Z4 Byte Register (1,3,5,7)7Ch Bit # Name Default 15 RZ47 0 14 RZ46 0 13 RZ45 0 12 RZ44 0 11 RZ43 0 10 RZ42 0 9 RZ41 0 8 RZ40 0 Bit # Name Default 7 RZ37 0 6 RZ36 0 5 RZ35 0 4 RZ34 0 3 RZ33 0 2 RZ32 0 1 RZ31 0 0 RZ30 0 Bits 15 to 8: Receive Z4 Byte (RZ4[7:0]) - These eight bits are the integrated version of the Z4 byte as extracted from the receive PLCP frame (This bits are zero in E3 mode). Bits 7 to 0: Receive Z3 Byte (RZ3[7:0]) - These eight bits are the integrated version of the Z3 byte as extracted from the receive PLCP frame. Register Name: Register Description: Register Address: PLCP.RZ56BR PLCP Receive Z5 and Z6 Byte Register (1,3,5,7)7Eh Bit # Name Default 15 RZ67 0 14 RZ66 0 13 RZ65 0 12 RZ64 0 11 RZ63 0 10 RZ62 0 9 RZ61 0 8 RZ60 0 Bit # Name Default 7 RZ57 0 6 RZ56 0 5 RZ55 0 4 RZ54 0 3 RZ53 0 2 RZ52 0 1 RZ51 0 0 RZ50 0 Bits 15 to 8: Receive Z6 Byte (RZ6[7:0]) - These eight bits are the integrated version of the Z6 byte as extracted from the receive PLCP frame (This bits are zero in E3 mode). Bits 7 to 0: Receive Z5 Byte (RZ5[7:0]) - These eight bits are the integrated version of the Z5 byte as extracted from the receive PLCP frame (This bits are zero in E3 mode). 330 DS3181/DS3182/DS3183/DS3184 12.13 FIFO Registers 12.13.1 Transmit FIFO Register Map The transmit FIFO block has five registers. Table 12-45. Transmit FIFO Register Map ADDRESS REGISTER (1,3,5,7)80h (1,3,5,7)82h (1,3,5,7)84h (1,3,5,7)86h (1,3,5,7)88h (1,3,5,7)8Ah (1,3,5,7)8Ch (1,3,5,7)8Eh FF.TCR FF.TLCR FF.TPAC -- FF.TSRL FF.TSRIE -- -- REGISTER DESCRIPTION FIFO Transmit Control Register FIFO Transmit Level Control Register FIFO Transmit Port Address Control Register Unused FIFO Transmit Status Register Latched Register FIFO Transmit Status Register Interrupt Enable Register Unused Unused 12.13.1.1 Register Bit Descriptions Register Name: Register Description: Register Address: FF.TCR FIFO Transmit Control Register (1,3,5,7)80h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 -- 0 3 -- 0 2 -- 0 1 -- 0 0 TFRST 1 Bit 0: Transmit FIFO Reset (TFRST) - When 0, the Transmit FIFO will resume normal operations, however, data is discarded until a start of packet/cell is received after RAM power-up is completed. When 1, the Transmit FIFO is emptied, any transfer in progress is halted, the FIFO RAM is powered down, the associated TDXA is forced low, and all incoming data is discarded. If the port was selected when the reset was initiated, the port will be deselected, and must be reselected (TEN deasserted with address on TADR or TSX asserted with address on TDATA) before any transfer will occur. 331 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: FF.TLCR FIFO Transmit Level Control Register (1,3,5,7)82h Bit # Name Default 15 -- 0 14 -- 0 13 TFAE5 0 12 TFAE4 1 11 TFAE3 0 10 TFAE2 0 9 TFAE1 0 8 TFAE0 0 Bit # Name Default 7 -- 0 6 -- 0 5 TFAF5 0 4 TFAF4 1 3 TFAF3 0 2 TFAF2 0 1 TFAF1 0 0 TFAF0 0 Bits 13 to 8: Transmit FIFO Almost Empty Level (TFAE[5:0]) - In POS-PHY packet processing mode, these six bits indicate the maximum number of four byte groups that can be stored in the Transmit FIFO for it to be considered "almost empty". E.g., a value of 30 (1Eh) results in the FIFO being "almost empty" when it contains 120 (78h) bytes or less. In cell processing mode, these bits are ignored. Bits 5 to 0: Transmit FIFO Almost Full Level (TFAF[5:0]) - In POS-PHY packet processing mode, these six bits indicate the maximum number of four byte groups that can be available in the Transmit FIFO for it to be considered "almost full". E.g., a value of 30 (1Eh) results in the FIFO being "almost full" when it has 120 (78h) bytes or less available. In cell processing mode, TFAF[5:2] are ignored, and TFAF[1:0] indicate the maximum number of cells that can be available in the Transmit FIFO for it to be considered "almost full". Register Name: Register Description: Register Address: FF.TPAC FIFO Transmit Port Address Control Register (1,3,5,7)84h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 TPA4 0 3 TPA3 0 2 TPA2 0 1 TPA1 0 0 TPA0 0 Bits 4 to 0: Transmit FIFO System Port Address (TPA[4:0]) - These five bits set the Transmit FIFO system interface port address used to poll the Transmit FIFO for fill status, and select it for data transfer. In Level 2 mode, if bits TPA[4:0] are set to a value of 1Fh, the port is disabled. 332 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: FF.TSRL FIFO Transmit Status Register Latched Register (1,3,5,7)88h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 -- 6 -- 5 -- 4 TFATL 3 TFSTL 2 TFITL 1 TFUL 0 TFOL Bit 4: Transmit FIFO Aborted Transfer Latched (TFATL) - This bit is set when a transfer is aborted. An aborted transfer does not occur in UTOPIA mode. In POS-PHY mode, an aborted transfer occurs when a packet error (a transfer with TERR and TEOP asserted) occurs. An aborted transfer is stored in the transmit FIFO with an abort indication. Bit 3: Transmit FIFO Short Transfer Latched (TFSTL) - This bit is set when a "short transfer" is received. In UTOPIA mode, a "short transfer" occurs when a start of cell (a transfer with TSOC asserted) occurs before the previous cell transfer has been completed. In POS-PHY mode, a "short transfer" occurs when a start of packet (a transfer with TSOP asserted) occurs after a previous start of packet, but before an end of packet (a transfer with TEOP asserted). In UTOPIA mode, the short transfer data is discarded. In POS-PHY mode, a short transfer is stored in the transmit FIFO with an abort indication. Bit 2: Transmit FIFO Invalid Transfer Latched (TFITL) - This bit is set when an "invalid transfer" is initiated. In UTOPIA mode, an "invalid transfer" occurs when additional cell data is transferred after the last transfer of a cell and before a transfer with TSOC asserted. In POS-PHY mode, an "invalid transfer" occurs when packet data is transferred after an end of packet, but before a start of packet (this includes another end of packet transfer). The invalid transfer data is discarded. Bit 1: Transmit FIFO Underflow Latched (TFUL) - This bit is set when a Transmit FIFO underflow condition occurs. An underflow condition results in a loss of data. Bit 0: Transmit FIFO Overflow Latched (TFOL) - This bit is set when a Transmit FIFO overflow condition occurs. An overflow condition results in a loss of data. 333 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: FF.TSRIE FIFO Transmit Status Register Interrupt Enable Register (1,3,5,7)8Ah Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 TFATIE 0 3 TFSTIE 0 2 TFITIE 0 1 TFUIE 0 0 TFOIE 0 Bit 4: Transmit FIFO Aborted Transfer Interrupt Enable (TFATIE) - This bit enables an interrupt if the TFATL bit in the FF.TSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 3: Transmit FIFO Short Transfer Interrupt Enable (TFSTIE) - This bit enables an interrupt if the TFSTL bit in the FF.TSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 2: Transmit FIFO Invalid Transfer Interrupt Enable (TFITIE) - This bit enables an interrupt if the TFITL bit in the FF.TSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled 1 = interrupt enabled Bit 1: Transmit FIFO Underflow Interrupt Enable (TFUIE) - This bit enables an interrupt if the TFUL bit in the FF.TSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 0: Transmit FIFO Overflow Interrupt Enable (TFOIE) - This bit enables an interrupt if the TFOL bit in the FF.TSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled 334 DS3181/DS3182/DS3183/DS3184 12.13.2 Receive FIFO Register Map The receive FIFO block has five registers. Table 12-46. Receive FIFO Register Map ADDRESS REGISTER (1,3,5,7)90h (1,3,5,7)92h (1,3,5,7)94h (1,3,5,7)96h (1,3,5,7)98h (1,3,5,7)9Ah (1,3,5,7)9Ch (1,3,5,7)9Eh FF.RCR FF.RLCR FF.RFPAC -- FF.RSRL FF.RSRIE --- -- REGISTER DESCRIPTION FIFO Receive Control Register FIFO Receive Level Control Register FIFO Receive Port Address Control Register Unused FIFO Receive Status Register Latched FIFO Receive Status Register Interrupt Enable Unused Unused 12.13.2.1 Register Bit Descriptions Register Name: Register Description: Register Address: FF.RCR FIFO Receive Control Register (1,3,5,7)90h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 -- 0 3 -- 0 2 -- 0 1 -- 0 0 RFRST 1 Bit 0: Receive FIFO Reset (RFRST) - When 0, the Receive FIFO will resume normal operations, however, data is discarded until a start of packet/cell is received after RAM power-up is completed. When 1, the Receive FIFO is emptied, any transfer in progress is halted, the FIFO RAM is powered down, the associated RDXA signal is forced low, and all incoming data is discarded. If the port was selected when the reset was initiated, the port will be deselected, and must be reselected (REN) deasserted with address on RADR or RSX asserted with address on RDATA) before any transfer will occur. 335 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: FF.RLCR FIFO Receive Level Control Register (1,3,5,7)92h Bit # Name Default 15 -- 0 14 -- 0 13 RFAE5 0 12 RFAE4 1 11 RFAE3 0 10 RFAE2 0 9 RFAE1 0 8 RFAE0 0 Bit # Name Default 7 -- 0 6 -- 0 5 RFAF5 0 4 RFAF4 1 3 RFAF3 0 2 RFAF2 0 1 RFAF1 0 0 RFAF0 0 Bits 13 to 8: Receive FIFO Almost Empty Level (RFAE[5:0]) - In POS-PHY packet processing mode, these six bits indicate the maximum number of four byte groups that can be stored in the Receive FIFO for it to be considered "almost empty". E.g., a value of 30 (1Eh) results in the FIFO being "almost empty" when it contains 120 (78h) bytes or less. In cell processing mode, RFAE[5:2] are ignored, and RFAE[1:0] indicate the maximum number of cells that can be stored in the Receive FIFO for it to be considered "almost empty". Bits 5 to 0: Receive FIFO Almost Full Level (RFAF[5:0]) - In POS-PHY packet processing mode, these six bits indicate the maximum number of four byte groups that can be available in the Receive FIFO for it to be considered "almost full". E.g., a value of 30 (1Eh) results in the FIFO being "almost full" when it has 120 (78h) bytes or less available. In cell processing mode, these bits are ignored. Register Name: Register Description: Register Address: FF.RFPAC FIFO Receive Port Address Control Register (1,3,5,7)94h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 RPA4 0 3 RPA3 0 2 RPA2 0 1 RPA1 0 0 RPA0 0 Bits 4 to 0: Receive FIFO System Port Address (RPA[4:0]) - These five bits set the Receive FIFO system interface port address used to poll the Receive FIFO for fill status, and select it for data transfer. Each port in the device must have a different port address. In Level 2 mode, if bits RPA[4:0] are set to a value of 1Fh, the port is disabled. 336 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: FF.RSRL FIFO Receive Status Register Latched (1,3,5,7)98h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 -- 6 -- 5 -- 4 -- 3 -- 2 -- 1 -- 0 RFOL Bit 0: Receive FIFO Overflow Latched (RFOL) - This bit is cleared when a logic one is written to this bit, and set when a Receive FIFO overflow condition occurs. An overflow condition results in a loss of data. Register Name: Register Description: Register Address: FF.RSRIE FIFO Receive Status Register Interrupt Enable (1,3,5,7)9Ah Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 -- 0 3 -- 0 2 -- 0 1 -- 0 0 RFOIE 0 Bit 0: Receive FIFO Overflow Interrupt Enable (RFOIE) - This bit enables an interrupt if the RFOL bit in the FF.RSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled 337 DS3181/DS3182/DS3183/DS3184 12.14 Cell/Packet Processor 12.14.1 Transmit Cell Processor Register Map The transmit cell processor block has 11 registers. Note: These registers are shared with the transmit packet processors. Table 12-47. Transmit Cell Processor Register Map ADDRESS REGISTER (1,3,5,7)A0h (1,3,5,7)A2h (1,3,5,7)A4h (1,3,5,7)A6h (1,3,5,7)A8h (1,3,5,7)AAh (1,3,5,7)ACh (1,3,5,7)AEh (1,3,5,7)B0h (1,3,5,7)B2h (1,3,5,7)B4h (1,3,5,7)B6h (1,3,5,7)B8h (1,3,5,7)BAh (1,3,5,7)BCh (1,3,5,7)BEh CP.TCR -- CP.TECC CP.THMRC CP.THPC1 CP.THPC2 CP.TFPPC CP.TSR CP.TSRL CP.TSRIE CP.TCCR1 CP.TCCR2 -- -- -- -- REGISTER DESCRIPTION Cell Processor Transmit Control Register Reserved Cell Processor Transmit Errored Cell Control Register Cell Processor Transmit HEC Error Mask Control Register Cell Processor Transmit Header Pattern Control Register 1 Cell Processor Transmit Header Pattern Control Register 2 Cell Processor Transmit Fill Cell Payload Pattern Control Register Cell Processor Transmit Status Register Cell Processor Transmit Status Register Latched Cell Processor Transmit Status Register Interrupt Enable Cell Processor Transmit Cell Count Register 1 Cell Processor Transmit Cell Count Register 2 Reserved Reserved Unused Unused 12.14.1.1 Register Bit Descriptions Register Name: Register Description: Register Address: CP.TCR Cell Processor Transmit Control Register (1,3,5,7)A0h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 TDSE 0 10 TDHE 0 9 THPE 0 8 TCPAD 0 Bit # Name Default 7 -- 0 6 -- 0 5 TFCH 0 4 TFCP 0 3 THSE 0 2 TSD 0 1 TBRE 0 0 TCPD 0 Bit 11: Transmit DSS Scrambling Enable (TDSE) - When 0, self-synchronous scrambling is enabled. When 1, DSS scrambling is enabled DSS mode is only applicable for un-framed or clear channel framing and bit synchronous modes. This bit is ignored if scrambling is disabled. Note: In byte synchronous and cell pass-through modes, self-synchronous scrambling is enabled regardless of the setting of this bit. Bit 10: Transmit DQDB HEC Processing Enable (TDHE) - When 0, the HEC is calculated over all four-header bytes. When 1, only the last three header bytes are used for HEC calculation. Bit 9: Transmit HEC Pass-through Enable (THPE) - When 0, the calculated HEC byte will overwrite the HEC byte in the cell. When 1, the HEC byte in the cell is passed through. Note: The calculated HEC is always inserted into cells that are received without a HEC byte. Bit 8: Transmit HEC Coset Polynomial Addition Disable (TCPAD) - When 0, the HEC coset polynomial addition is performed prior to inserting the HEC byte. When 1, HEC coset polynomial addition is disabled 338 DS3181/DS3182/DS3183/DS3184 Bit 5: Transmit Fill Cell Header Type (TFCH) - When 0, an idle cell header (00 00 00 01h) will be used in fill cells. When 1, a programmable header will be used in fill cells. The setting of this bit does not affect the contents of the cell payload bytes. Bit 4: Transmit Fill Cell Payload Type (TFCP) - When 0, an idle cell payload byte (6Ah) will be used in each payload byte fill cells. When 1, a programmable cell payload byte will be used in each payload byte fill cells. The setting of this bit does not affect the contents of the cell header bytes. Bit 3: Transmit Cell Header Scrambling Enable (THSE) - When 0, only the cell payload will be scrambled. When 1, the entire data stream (cell header and payload) is scrambled. This bit is ignored if scrambling is disabled, or DSS scrambling is enabled. When cell pass-through mode is enabled, the entire data stream will be scrambled if scrambling is enabled. Bit 2: Transmit Scrambling Disable (TSD) - When 0, scrambling is performed. When 1, scrambling is disabled. Bit 1: Transmit Bit Reordering Enable (TBRE) - When 0, bit reordering is disabled (The first bit transmitted is from the MSB of the transmit FIFO byte TFD[7]). When 1, bit reordering is enabled (The first bit transmitted is from the LSB of the transmit FIFO byte TFD[0]). Bit 0: Transmit Pass-Through Enable (TPTE) - When 0, pass-through mode is disabled and cell processing is enabled. When 1, all cell processing functions except scrambling and bit reordering are disabled and the cell processor is in pass-through mode. 339 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: CP.TECC Cell Processor Transmit Errored Cell Control Register (1,3,5,7)A4h Bit # Name Default 15 MEIMS 0 14 TCER6 0 13 TCER5 0 12 TCER4 0 11 TCER3 0 10 TCER2 0 9 TCER1 0 8 TCER0 0 Bit # Name Default 7 TCEN7 0 6 TCEN6 0 5 TCEN5 0 4 TCEN4 0 3 TCEN3 0 2 TCEN2 0 1 TCEN1 0 0 TCEN0 0 Bit 15: Manual Error Insert Mode Select (MEIMS) - When 0, the transmit manual error insertion signal (TMEI) will not cause errors to be inserted. When 1, TMEI will causes an error to be inserted when it transitions from a 0 to a 1. Note: Enabling TMEI does not disable error insertion using TCER[6:0] and TCEN[7:0]. Manual error insertion is available at the global level, but not on a per-port basis for the cell processor. (PORT.CR1.MEIM must be set for global error insertion to insert a packet error.) Bits 14 to 8: Transmit Errored Cell Insertion Rate (TCER[6:0]) - These seven bits indicate the rate at which errored cells are to be output. One out of every x * 10y cells is to be an errored cell. TCER[3:0] is the value x, and TCER[6:4] is the value y, which has a maximum value of 6. If TCER[3:0] has a value of 0h errored cell insertion is disabled. If TCER[6:4] has a value of 6xh or 7xh the errored cell rate will be x * 106. A TCER[6:0] value of 01h results in every cell being errored. A TCER[6:0] value of 0Fh results in every 15th cell being errored. A TCER[6:0] value of 11h results in every 10th cell being errored. Errored cell insertion starts when the TECC register is written with a TCER[3:0] value that is non-zero. If the TECC register is written to during the middle of an errored cell insertion process, the current process is halted, and a new process will be started using the new values of TCER[6:0] and TCEN[7:0}. Errored cell insertion ends when TCEN[7:0] errored cells have been transmitted. TCER[3:0] - X TCER[6:4] - Y TCER[6:0] ERROR RATE (x * 10y ) 0h XXh X0h DISABLED 1h 0Xh 01h 1 out of 1 cells Fh 0Xh 0Fh 1 out of 15 cells 1h 1Xh 11h 1 out of 10 cells 1h 6Xh 61h 1 out of 106 cells 1h 7Xh 71h 1 out of 106 cells Bits 7 to 0: Transmit Errored Cell Insertion Number (TCEN[7:0]) - These eight bits indicate the total number of errored cells to be transmitted. A value of FFh results in continuous errored cell insertion at the specified rate. 340 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: CP.THMRC Cell Processor Transmit HEC Error Mask Control Register (1,3,5,7)A6h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 THEM7 0 6 THEM6 0 5 THEM5 0 4 THEM4 0 3 THEM3 0 2 THEM2 0 1 THEM1 0 0 THEM0 0 Bits 7 to 0: Transmit HEC Error Mask (THEM[7:0]) -These bits control the error insertion into the HEC byte. Setting these bits will corrupt the associated HEC bit during cell error insertion. Based on the value set in this register, the far end will detect three types of errors: an error in the HEC, a single bit error in the header, or multiple bit errors in the header. Default (THEM[7:0] = 00h) is no error inserted. If a single bit error is selected, the table below also shows which bit of the 32-bit HEC header will be corrupted. Table 12-48 indicates the type of error inserted by a specific mask value. Note: If a single bit error is inserted in the HEC, and the far-end has single bit error correction enabled, this will cause the indicated header bit to be corrupted. Table 12-48. HEC Error Mask VALUE 01h-02h 03h 04h 05h-06h 07h 08h 09h-0Ah 0Bh 0Ch-0Dh 0Eh 0Fh 10h 11h-14h 15h 16h 17h-1Dh 1Eh 1Fh 20h 21h-29h 2Ah 2Bh 2Ch 2Dh-30h 31h ERROR TYPE HEC Multi HEC Multi Single HEC Multi Single Multi Single Multi HEC Multi Single Single Multi Single Multi HEC Multi Single Multi Single Multi Single BIT VALUE - - - 32 - - 09 - 31 - - - 24 08 - 30 - - - 23 - 07 - 01 32h-37h 38h 39h-3Fh 40h 41h-42h 43h 44h-50h 51h 52h-53h 54h 55h-56h 57h 58h 59h-5Ah 5Bh 5Ch-66h 67h 68h-6Ah 6Bh 6Ch-6Fh 70h 71h-7Fh 80h 81h-85h 86h ERROR TYPE Multi Single Multi HEC Multi Single Multi Single Multi Single Multi Single Single Multi Single Multi Single Multi Single Multi Single Multi HEC Multi Single 341 BIT VALUE - 29 - - - 11 - 13 - 22 - 20 06 - 18 - 04 - 16 - 28 - - - 10 87h-88h 89h 90h-9Ah 9Bh 9Ch-A1h A2h A3h-A7h A8h A9h-AAh ABh ACh-ADh AEh AFh B0h B1h-B5h B6h B7h-C6h C7h C8h-CDh CEh CFh-D5h D6h D7h-DFh E0h E1h-FFh ERROR TYPE Multi Single Multi Single Multi Single Multi Single Multi Single Multi Single Multi Single Multi Single Multi Single Multi Single Multi Single Multi Single Multi BIT - 25 - 02 - 12 - 21 - 14 - 19 - 05 - 17 - 26 - 03 - 15 - 27 - DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: CP.THPC1 Cell Processor Transmit Header Pattern Control Register 1 (1,3,5,7)A8h Bit # Name Default 15 THP15 0 14 THP14 0 13 THP13 0 12 THP12 0 11 THP11 0 10 THP10 0 9 THP9 0 8 THP8 0 Bit # Name Default 7 THP7 0 6 THP6 0 5 THP5 0 4 THP4 0 3 THP3 0 2 THP2 0 1 THP1 0 0 THP0 0 Bits 15 to 0: Transmit Programmable Header Pattern (THP[15:0]) - Lower 16 bits of 32 bits. Register description follows next register. Register Name: Register Description: Register Address: CP.THPC2 Cell Processor Transmit Header Pattern Control Register 2 (1,3,5,7)AAh Bit # Name Default 15 THP31 0 14 THP30 0 13 THP29 0 12 THP28 0 11 THP27 0 10 THP26 0 9 THP25 0 8 THP24 0 Bit # Name Default 7 THP23 0 6 THP22 0 5 THP21 0 4 THP20 0 3 THP19 0 2 THP18 0 1 THP17 0 0 THP16 0 Bits 15 to 0: Transmit Programmable Header Pattern (THP[31:16]) Upper 16 bits of 32 bits. Transmit Programmable Header Pattern (THP[31:0]) - These 32 bits indicate the header bit pattern to be used in the header of fill cells when the CP.TCR register bit TFCH is set. Register Name: Register Description: Register Address: CP.TFPPC Cell Processor Transmit Fill Cell Payload Pattern Control Register (1,3,5,7)ACh Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 TFPP7 0 6 TFPP6 0 5 TFPP5 0 4 TFPP4 0 3 TFPP3 0 2 TFPP2 0 1 TFPP1 0 0 TFPP0 0 Bits 7 to 0: Transmit Fill Cell Payload Pattern (TFPP[7:0]) - These eight bits indicate the value to be placed in the payload bytes of the fill cells when the CP.TCR register bit TFCP is set.. 342 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: CP.TSR Cell Processor Transmit Status Register (1,3,5,7)AEh Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 -- 6 -- 5 -- 4 -- 3 -- 2 -- 1 -- 0 TECF Bit 0: Transmit Errored Cell Insertion Finished (TECF) - This bit is set when the number of errored cells indicated by the TCEN[7:0] bits in the TECC register have been transmitted. This bit is cleared when errored cell insertion is disabled, or a new errored cell insertion process is initiated. Register Name: Register Description: Register Address: CP.TSRL Cell Processor Transmit Status Register Latched (1,3,5,7)B0h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 -- 6 -- 5 -- 4 -- 3 -- 2 -- 1 -- 0 TECFL Bit 0: Transmit Errored Cell Insertion Finished Latched (TECFL) - This bit is set when the TECF bit in the CP.TSR register transitions from zero to one. Register Name: Register Description: Register Address: CP.TSRIE Cell Processor Transmit Status Register Interrupt Enable (1,3,5,7)B2h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 -- 0 3 -- 0 2 -- 0 1 -- 0 0 TECFIE 0 Bit 0: Transmit Errored Cell Insertion Finished Interrupt Enable (TECFIE) - This bit enables an interrupt if the TECFL bit in the CP.TSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled 343 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: CP.TCCR1 Cell Processor Transmit Cell Count Register 1 (1,3,5,7)B4h Bit # Name Default 15 TCC15 0 14 TCC14 0 13 TCC13 0 12 TCC12 0 11 TCC11 0 10 TCC10 0 9 TCC9 0 8 TCC8 0 Bit # Name Default 7 TCC7 0 6 TCC6 0 5 TCC5 0 4 TCC4 0 3 TCC3 0 2 TCC2 0 1 TCC1 0 0 TCC0 0 Bits 15 to 0: Transmit Cell Count (TCC[15:0]) - Lower 16 bits of 24 bits. Register description follows next register. Register Name: Register Description: Register Address: CP.TCCR2 Cell Processor Transmit Cell Count Register 2 (1,3,5,7)B6h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 TCC23 0 6 TCC22 0 5 TCC21 0 4 TCC20 0 3 TCC19 0 2 TCC18 0 1 TCC17 0 0 TCC16 0 Bits 7 to 0: Transmit Cell Count (TCC[23:16]) - Upper 8 bits of Register. Transmit Cell Count (TCC[23:0]) - These 24 bits indicate the number of cells extracted from the Transmit FIFO and output in the outgoing data stream. This register is updated via the PMU signal (see Section 10.4.5). 344 DS3181/DS3182/DS3183/DS3184 12.14.2 Receive Cell Processor The receive cell processor block has 18 registers. 12.14.2.1 Receive Cell Processor Register Map Table 12-49. Receive Cell Processor Register Map ADDRESS (1,3,5,7)C0h (1,3,5,7)C2h (1,3,5,7)C4h (1,3,5,7)C6h (1,3,5,7)C8h (1,3,5,7)CAh (1,3,5,7)CCh (1,3,5,7)CEh (1,3,5,7)D0h (1,3,5,7)D2h (1,3,5,7)D4h (1,3,5,7)D6h (1,3,5,7)D8h (1,3,5,7)DAh (1,3,5,7)DCh (1,3,5,7)DEh (1,3,5,7)E0h (1,3,5,7)E2h (1,3,5,7)E4h (1,3,5,7)E6h (1,3,5,7)E8h (1,3,5,7)EAh (1,3,5,7)ECh (1,3,5,7)EEh (1,3,5,7)F0h (1,3,5,7)F2h (1,3,5,7)F4h (1,3,5,7)F6h (1,3,5,7)F8h (1,3,5,7)FAh (1,3,5,7)FCh (1,3,5,7)FEh REGISTER CP.RCR1 -- CP.RHPC1 CP.RHPC2 CP.RHPMC1 CP.RHPMC2 CP.RLTC CP.RSR CP.RSRL CP.RSRIE CP.RCCR1 CP.RCCR2 CP.RECCR1 CP.RECCR2 CP.RHPCR1 CP.RHPCR2 CP.RCCCR1 CP.RCCCR2 CP.RFCCR1 CP.RFCCR2 -- -- -- -- -- -- -- -- -- -- -- -- REGISTER DESCRIPTION Cell Processor Receive Control Register 1 Reserved Cell Processor Receive Header Pattern Control Register 1 Cell Processor Receive Header Pattern Control Register 2 Cell Processor Receive Header Pattern Mask Control Register 1 Cell Processor Receive Header Pattern Mask Control Register 2 Cell Processor Receive LCD Threshold Control Register Cell Processor Receive Status Register Cell Processor Receive Status Register Latched Cell Processor Receive Status Register Interrupt Enable Cell Processor Receive Cell Count Register 1 Cell Processor Receive Cell Count Register 2 Cell Processor Receive Errored Header Count Register 1 Cell Processor Receive Errored Header Count Register 2 Cell Processor Receive Header Pattern Cell Count Register 1 Cell Processor Receive Header Pattern Cell Count Register 2 Cell Processor Receive Corrected Cell Count Register 1 Cell Processor Receive Corrected Cell Count Register 2 Cell Processor Receive Filtered Idle/Unassigned/Invalid Cell Count Register 1 Cell Processor Receive Filtered Idle/Unassigned/Invalid Cell Count Register 2 Reserved Reserved Reserved Reserved Unused Unused Unused Unused Unused Unused Unused Unused 345 DS3181/DS3182/DS3183/DS3184 12.14.2.2 Register Bit Descriptions Register Name: Register Description: Register Address: CP.RCR1 Cell Processor Receive Control Register 1 (1,3,5,7)C0h Bit # Name Default 15 RDDE 0 14 RDHE 0 13 RECED 0 12 RHPM1 0 11 RHPM0 0 10 RICFD 0 9 RUCFE 0 8 RICFE 0 Bit # Name Default 7 RROC1 0 6 RROC0 0 5 RCPAD 0 4 RHECD 0 3 RHDE 0 2 RDD 0 1 RBRE 0 0 RPTE 0 Bit 15: Receive DSS Descrambling Enable (RDDE) - When 0, self-synchronous descrambling is enabled. When 1, DSS descrambling is enabled. DSS mode is only applicable for un-framed or clear channel framing and bit synchronous modes. This bit is ignored if descrambling is disabled. Note: In byte synchronous and cell passthrough modes, self-synchronous descrambling is enabled regardless of the setting of this bit. Bit 14: Receive DQDB HEC Processing Enable (RDHE) - When 0, the HEC is calculated over all four-header bytes. When 1, only the last three header bytes are used for HEC calculation. Bit 13: Receive Errored Cell Extraction Disable (RECED) - When 0, errored cells are extracted. When 1, errored cells are passed on. Bits 12 to 11: Receive Header Pattern Comparison Mode (RHPM[1:0]) - These two bits control the operation of the header pattern comparison function. 00 = Count match: Cells that match the header pattern are counted. 01 = Count no match - Cells that do not match the header pattern are counted. 10 = Discard match - Cells that match the header pattern are counted and discarded. 11 = Discard no match - Cells that do not match the header pattern are counted and discarded. Bit 10: Receive Idle Cell Filtering Disable (RICFD) - When 0, idle cells are discarded. When 1, idle cells are passed on. Bit 9: Receive Unassigned Cell Filtering Enable (RUCFE) - When 0, unassigned cells are passed on. When 1, unassigned cells are counted and discarded. Bit 8: Receive Invalid Cell Filtering Enable (RICFE) - When 0, invalid cells are passed on. When 1, invalid cells are discarded. Bits 7 to 6: Receive Error Monitoring Required OK Cells (RROC[1:0]) - These two bits indicate the number of good cells required to transition from the "Detection" state to the "Correction" state, which enables single bit correction of the header (see Figure 10-28). 00 = 1 good cell is required. 01 = 2 good cells are required. 10 = 4 good cells are required. 11 = 8 good cells are required. Bit 5: Receive HEC Coset Polynomial Addition Disable (RCPAD) - When 0, the HEC coset polynomial addition is performed prior to checking the HEC byte. When 1, HEC coset polynomial addition is disabled Bit 4: Receive Header Error Correction Disable (RHECD) - When 0, single bit header error correction is enabled. When 1, header error correction is disabled and all errors are treated as an un-correctable error. Bit 3: Receive Cell Header Descrambling Enable (RHDE) - When 0, only the cell payload will be descrambled. When 1, the entire data stream (cell header and payload) is descrambled. This bit is ignored if descrambling is disabled or DSS descrambling is enabled. When cell pass-through mode is enabled, the entire data stream will be descrambled if descrambling is enabled. Bit 2: Receive Descrambling Disable (RDD) - When 0, descrambling is performed. When 1, descrambling is disabled. 346 DS3181/DS3182/DS3183/DS3184 Bit 1: Receive Bit Reordering Enable (RBRE) - When 0, bit reordering is disabled (The first bit received is stored in the MSB of the receive FIFO byte). When 1, bit reordering is enabled (The first bit received is stored in the LSB of the receive FIFO byte). Bit 0: Receive Pass-Through Enable (RPTE) - When 0, pass-through mode is disabled and cell processing is enabled. When 1, the cell processor is in pass-through mode, and all cell processing functions except descrambling and bit reordering are disabled. Register Name: Register Description: Register Address: CP.RHPC1 Cell Processor Receive Header Pattern Control Register 1 (1,3,5,7)C4h Bit # Name Default 15 RHP15 0 14 RHP14 0 13 RHP13 0 12 RHP12 0 11 RHP11 0 10 RHP10 0 9 RHP9 0 8 RHP8 0 Bit # Name Default 7 RHP7 0 6 RHP6 0 5 RHP5 0 4 RHP4 0 3 RHP3 0 2 RHP2 0 1 RHP1 0 0 RHP0 0 Bits 15 to 0: Receive Header Pattern (RHP[15:0]) - Lower 16 bits of 32 bits. Register description follows next register. Register Name: Register Description: Register Address: CP.RHPC2 Cell Processor Receive Header Pattern Control Register 2 (1,3,5,7)C6h Bit # Name Default 15 RHP31 0 14 RHP30 0 13 RHP29 0 12 RHP28 0 11 RHP27 0 10 RHP26 0 9 RHP25 0 8 RHP24 0 Bit # Name Default 7 RHP23 0 6 RHP22 0 5 RHP21 0 4 RHP20 0 3 RHP19 0 2 RHP18 0 1 RHP17 0 0 RHP16 0 Bits 15 to 0: Receive Header Pattern (RHP[31:16]) - Upper 16 bits of 32 bits. Receive Header Pattern (RHP[31:0]) - These 32 bits indicate the receive header bit pattern to be detected by the header pattern comparison function. 347 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: CP.RHPMC1 Cell Processor Receive Header Pattern Mask Control Register 1 (1,3,5,7)C8h Bit # Name Default 15 RHPD15 0 14 RHPD14 0 13 RHPD13 0 12 RHPD12 0 11 RHPD11 0 10 RHPD10 0 9 RHPD9 0 8 RHPD8 0 Bit # Name Default 7 RHPD7 0 6 RHPD6 0 5 RHPD5 0 4 RHPD4 0 3 RHPD3 0 2 RHPD2 0 1 RHPD1 0 0 RHPD0 0 Bit 15 to 0: Receive Header Pattern Comparison Disable (RHPD[15:0]) - Lower 16 bits of 32 bits. Register description follows next register. Register Name: Register Description: Register Address: CP.RHPMC2 Cell Processor Receive Header Pattern Mask Control Register 2 (1,3,5,7)CAh Bit # Name Default 15 RHPD31 0 14 RHPD30 0 13 RHPD29 0 12 RHPD28 0 11 RHPD27 0 10 RHPD26 0 9 RHPD25 0 8 RHPD24 0 Bit # Name Default 7 RHPD23 0 6 RHPD22 0 5 RHPD21 0 4 RHPD20 0 3 RHPD19 0 2 RHPD18 0 1 RHPD17 0 0 RHPD16 0 Bits 15 to 0: Receive Header Pattern Comparison Disable (RHPD[31:16]) - Upper 16 bits of 32 bits. Receive Header Pattern Comparison Disable (RHPD[31:0]) - These 32 bits indicate whether or not the associated header bit is checked by the header pattern comparison function. If RHPD[x] is high, the header bit x is ignored during the header pattern comparison (don't care). If RHPD[x] is low, the associated bit in the header must match RHP[x] in the receive header pattern control register RHPC. Register Name: Register Description: Register Address: CP.RLTC Cell Processor Receive LCD Threshold Control Register (1,3,5,7)CCh Bit # Name Default 15 RLT15 0 14 RLT14 0 13 RLT13 0 12 RLT12 0 11 RLT11 0 10 RLT10 0 9 RLT9 0 8 RLT8 1 Bit # Name Default 7 RLT7 0 6 RLT6 1 5 RLT5 1 4 RLT4 0 3 RLT3 1 2 RLT2 0 1 RLT1 0 0 RLT0 0 Bits 15 to 0: Receive LCD Threshold (RLT[15:0]) - These 16 bits indicate the number of consecutive cell periods the cell delineation state machine must be in an Out of Cell Delineation (OCD) condition before it declares or terminate a Loss of Cell Delineation (LCD) condition. A value of 0000h causes LCD to be declared at the same time as OCD. The register has a default value after reset of 360 (decimal). 348 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: CP.RSR Cell Processor Receive Status Register (1,3,5,7)CEh Bit # Name 15 -- 14 -- 13 -- 12 -- 11 OOS 10 -- 9 OCD 8 LCD Bit # Name 7 -- 6 -- 5 -- 4 -- 3 -- 2 RECC 1 RHPC 0 RCHC Bit 11: Out Of Sync (OOS) - This read-only bit indicates that a DSS Out Of Sync (OOS) state exists. DSS OOS occurs when the DSS Scrambler Synchronization state machine is in the "Load" or "Verify" state, and DSS scrambling has been enabled. Bit 9: Out Of Cell Delineation (OCD) - This read-only bit indicates that an Out of Cell Delineation condition (OCD) exists. When DSS scrambling is disabled, OCD occurs when the HEC Error Monitoring state machine is in the "OCD" state. When DSS scrambling is enable, OCD occurs when the DSS OCD Detection state machine is in the "OCD" state. Bit 8: Loss Of Cell Delineation (LCD) - This read-only bit indicate that a Loss of Cell Delineation state exists. LCD occurs when OCD persists for the period programmed in the LCD threshold control register RLTC. Bit 2: Receive Errored Header Cell Count (RECC) - This read-only bit indicates that the receive errored header cell count is non-zero. Bit 1: Receive Header Pattern Cell Count (RHPC) - This read-only bit indicates that the receive header pattern comparison cell count is non-zero. Bit 0: Receive Corrected Cell Count (RCHC) - This read-only bit indicates that the receive corrected header cell count is non-zero. 349 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: CP.RSRL Cell Processor Receive Status Register Latched (1,3,5,7)D0h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 OOSL 10 COCDL 9 OCDCL 8 LCDCL Bit # Name 7 RECL 6 RCHL 5 RIDL 4 RUDL 3 RIVDL 2 RECCL 1 RHPCL 0 RCHCL Bit 11: Out Of Sync Change Latched (OOSL) - This bit is set when the OOS bit in the CP.RSR register changes state. Bit 10: Change Of Cell Delineation Latched (COCDL) - This bit is set when the data path cell counters are updated with a new cell delineation that is different from the previous cell delineation. Bit 9: Out Of Cell Delineation Change Latched (OCDCL) - This bit is set when the OCD bit in the CP.RSR register changes state. Note: Immediately after a reset, this bit will be set to one. Bit 8: Loss Of Cell Delineation Change Latched (LCDCL) - This bit is set when the LCD bit in the CP.RSR register changes state Bit 7: Receive Errored Header Cell Latched (RECL) - This bit is set when a cell with an errored header is discarded. Bit 6: Receive Corrected Header Cell Latched (RCHL) - This bit is set when a cell with a single header error is corrected. Bit 5: Receive Idle Cell Detection Latched (RIDL) - This bit is set when an idle cell is discarded. Bit 4: Receive Unassigned Cell Detection Latched (RUDL) - This bit is set when an unassigned cell is discarded. Bit 3: Receive Invalid Cell Detection Latched (RIVDL) - This bit is set when an invalid cell is discarded. Bit 2: Receive Errored Header Cell Count Latched (RECCL) - This bit is set when the RECC bit in the CP.RSR register transitions from zero to one. Bit 1: Receive Header Pattern Cell Count Latched (RHPCL) - This bit is set when the RHPC bit in the CP.RSR register transitions from zero to one. Bit 0: Receive Corrected Header Cell Count Latched (RCHCL) - This bit is set when the RCHC bit in the CP.RSR register transitions from zero to one. 350 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address/Type: CP.RSRIE Cell Processor Receive Status Register Interrupt Enable (1,3,5,7)D2h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 OOSIE 0 10 COCDIE 0 9 OCDCIE 0 8 LCDCIE 0 Bit # Name Default 7 RECIE 0 6 RCHIE 0 5 RIDIE 0 4 RUDIE 0 3 RIVDIE 0 2 RECCIE 0 1 RHPCIE 0 0 RCHCIE 0 Bit 11: Out Of Sync Change Interrupt Enable (OOSIE) - This bit enables an interrupt if the OOSL bit in the CP.RSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 10: Change Of Cell Delineation Interrupt Enable (COCDIE) - This bit enables an interrupt if the COCDL bit in the CP.RSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 9: Out Of Cell Delineation Change Interrupt Enable (OCDCIE) - This bit enables an interrupt if the OCDCL bit in the CP.RSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 8: Loss Of Cell Delineation Change Interrupt Enable (LCDCIE) - This bit enables an interrupt if the LCDCL bit in the CP.RSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 7: Receive Errored Header Cell Interrupt Enable (RECIE) - This bit enables an interrupt if the RECL bit in the CP.RSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 6: Receive Corrected Header Cell Interrupt Enable (RCHIE) - This bit enables an interrupt if the RCHL bit in the CP.RSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 5: Receive Idle Cell Detection Interrupt Enable (RIDIE) - This bit enables an interrupt if the RIDL bit in the CP.RSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 4: Receive Unassigned Cell Detection Interrupt Enable (RUDIE) - This bit enables an interrupt if the RUDL bit in the CP.RSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 3: Receive Invalid Cell Detection Interrupt Enable (RIVDIE) - This bit enables an interrupt if the RIVDL bit in the CP.RSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 2: Receive Errored Header Cell Count Interrupt Enable (RECCIE) - This bit enables an interrupt if the RECCL bit in the CP.RSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled 351 DS3181/DS3182/DS3183/DS3184 Bit 1: Receive Header Pattern Cell Count Interrupt Enable (RHPCIE) - This bit enables an interrupt if the RHFCL bit in the CP.RSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 0: Receive Corrected Header Cell Count Interrupt Enable (RCHCIE) - This bit enables an interrupt if the RCHCL bit in the CP.RSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Register Name: Register Description: Register Address: CP.RCCR1 Cell Processor Receive Cell Count Register 1 (1,3,5,7)D4h Bit # Name Default 15 RCC15 0 14 RCC14 0 13 RCC13 0 12 RCC12 0 11 RCC11 0 10 RCC10 0 9 RCC9 0 8 RCC8 0 Bit # Name Default 7 RCC7 0 6 RCC6 0 5 RCC5 0 4 RCC4 0 3 RCC3 0 2 RCC2 0 1 RCC1 0 0 RCC0 0 Bits 15 to 0: Receive Cell Count (RCC[15:0]) - Lower 16 bits of 24 bits. Register description follows next register. Register Name: Register Description: Register Address: CP.RCCR2 Cell Processor Receive Cell Count Register 2 (1,3,5,7)D6h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 Bit # Name Default 7 RCC23 0 6 RCC22 0 5 RCC21 0 4 RCC20 0 3 RCC19 0 2 RCC18 0 1 RCC17 0 8 -- 0 0 RCC16 0 Bits 7 to 0: Receive Cell Count (RCC[23:16]) - Upper 8 bits of Register. Receive Cell Count (RCC[23:0]) - These 24 bits indicate the number of cells stored in the receive FIFO. Note: Cells discarded due to system loopback or an overflow condition will be included in this count. This register is updated via the PMU signal (see Section 10.4.5). 352 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: CP.RECCR1 Cell Processor Receive Errored Header Count Register 1 (1,3,5,7)D8h Bit # Name Default 15 RECC15 0 14 RECC14 0 13 RECC13 0 12 RECC12 0 11 RECC11 0 10 RECC10 0 9 RECC9 0 8 RECC8 0 Bit # Name Default 7 RECC7 0 6 RECC6 0 5 RECC5 0 4 RECC4 0 3 RECC3 0 2 RECC2 0 1 RECC1 0 0 RECC0 0 Bits 15 to 0: Receive Errored Header Count (RECC[15:0]) - Lower 16 bits of 24 bits. Register description follows next register. Register Name: Register Description: Register Address: CP.RECCR2 Cell Processor Receive Errored Header Count Register 2 (1,3,5,7)DAh Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 Bit # Name Default 7 RECC23 0 6 RECC22 0 5 RECC21 0 4 RECC20 0 3 RECC19 0 2 RECC18 0 1 RECC17 0 8 -- 0 0 RECC16 0 Bits 7 to 0: Receive Errored Header Count (RECC[23:16]) Receive Errored Header Count (RECC[23:0]) - These 24 bits indicate the number of cells received with uncorrected header errors and discarded. If errored cell extraction is disabled, this count will be zero. Cells included in this count will not be included in any other count. This register is updated via the PMU signal (see Section 10.4.5). Register Name: Register Description: Register Address: CP.RHPCR1 Cell Processor Receive Header Pattern Cell Count Register 1 (1,3,5,7)DCh Bit # Name Default 15 RHPC15 0 14 RHPC14 0 13 RHPC13 0 12 RHPC12 0 11 RHPC11 0 10 RHPC10 0 9 RHPC9 0 8 RHPC8 0 Bit # Name Default 7 RHPC7 0 6 RHPC6 0 5 RHPC5 0 4 RHPC4 0 3 RHPC3 0 2 RHPC2 0 1 RHPC1 0 0 RHPC0 0 Bits 15 to 0: Receive Header Pattern Comparison Cell Count (RHPC[15:0]) - Lower 16 bits of 24 bits. Register description follows next register. 353 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: CP.RHPCR2 Cell Processor Receive Header Pattern Cell Count Register #2 (1,3,5,7)DEh Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 RHPC23 0 6 RHPC22 0 5 RHPC21 0 4 RHPC20 0 3 RHPC19 0 2 RHPC18 0 1 RHPC17 0 0 RHPC16 0 Bits 7 to 0: Receive Header Pattern Comparison Cell Count (RHPC[23:16]) - Upper 8 bits of Register. Receive Header Pattern Comparison Cell Count (RHPC[23:0]) - These 24 bits indicate the number of cells identified during the header pattern comparison processes. In the header pattern comparison count and discard match modes, this will be a count of cells with a matching header. In the header pattern comparison count and discard no match modes, this will be a count of cells without a matching header. In the header pattern comparison count (match and no match) modes, this count will also be included in the receive cell count registers. In the header pattern comparison discard (match or no match) modes, this count will not be included in any other count. This register is updated via the PMU signal (see Section 10.4.5). Register Name: Register Description: Register Address: CP.RCCCR1 Cell Processor Receive Corrected Cell Count Register 1 (1,3,5,7)E0h Bit # Name Default 15 RCHC15 0 14 RCHC14 0 13 RCHC13 0 12 RCHC12 0 11 RCHC11 0 10 RCHC10 0 9 RCHC9 0 8 RCHC8 0 Bit # Name Default 7 RCHC7 0 6 RCHC6 0 5 RCHC5 0 4 RCHC4 0 3 RCHC3 0 2 RCHC2 0 1 RCHC1 0 0 RCHC0 0 Bits 15 to 0: Receive Corrected Header Count (RCHC[15:0]) - Lower 16 bits of 24 bits. Register description follows next register. 354 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: CP.RCCCR2 Cell Processor Receive Corrected Cell Count Register 2 (1,3,5,7)E2h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 Bit # Name Default 7 RCHC23 0 6 RCHC22 0 5 RCHC21 0 4 RCHC20 0 3 RCHC19 0 2 RCHC18 0 1 RCHC17 0 8 -- 0 0 RCHC16 0 Bits 7 to 0: Receive Corrected Header Count (RCHC[23:16]) - Upper 8 bits of Register. Receive Corrected Header Count (RCHC[23:0]) - These 24 bits indicate the number of cells that have had header errors corrected. If header error correction is disabled, this count will be zero. This count will be included in the receive cell count registers (CP.RCCR), receive filtered idle/unassigned/invalid cell count registers (CP.RFCCR), or receive header pattern cell count registers (CP.RHPCR). This register is updated via the PMU signal (see Section 10.4.5). Register Name: Register Description: Register Address: CP.RFCCR1 Cell Processor Receive Filtered Idle/Unassigned/Invalid Cell Count Register 1 (1,3,5,7)E4h Bit # Name Default 15 RFCC15 0 14 RFCC14 0 13 RFCC13 0 12 RFCC12 0 11 RFCC11 0 10 RFCC10 0 9 RFCC9 0 8 RFCC8 0 Bit # Name Default 7 RFCC7 0 6 RFCC6 0 5 RFCC5 0 4 RFCC4 0 3 RFCC3 0 2 RFCC2 0 1 RFCC1 0 0 RFCC0 0 Bits 15 to 0: Receive Filtered Cell Count (RFCC[15:0]) - Lower 16 bits of 24 bits. Register description follows next register. 355 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: CP.RFCCR2 Cell Processor Receive Filtered Idle/Unassigned/Invalid Cell Count Register #2 (1,3,5,7)E6h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 RFCC23 0 6 RFCC22 0 5 RFCC21 0 4 RFCC20 0 3 RFCC19 0 2 RFCC18 0 1 RFCC17 0 0 RFCC16 0 Bits 7 to 0: Receive Filtered Cell Count (RFCC[23:16]) - Upper 8 bits of Register. Receive Filtered Cell Count (RFCC[23:0]) - These 24 bits indicate the number of cells that were discarded during the cell filtering processes (idle, unassigned, and/or invalid). If all cell filtering is disabled, this count will be zero. Cells included in this count will not be included in any other count. This register is updated via the PMU signal (see Section 10.4.5). 356 DS3181/DS3182/DS3183/DS3184 12.14.3 Transmit Packet Processor Register Map The transmit packet processor block uses 10 registers. Note: These registers are shared with the transmit cell processor registers. Table 12-50. Transmit Packet Processor Register Map ADDRESS REGISTER REGISTER DESCRIPTION (1,3,5,7)A0h (1,3,5,7)A2h (1,3,5,7)A4h (1,3,5,7)A6h (1,3,5,7)A8h (1,3,5,7)AAh (1,3,5,7)ACh (1,3,5,7)AEh (1,3,5,7)B0h (1,3,5,7)B2h (1,3,5,7)B4h (1,3,5,7)B6h (1,3,5,7)B8h (1,3,5,7)BAh (1,3,5,7)BCh (1,3,5,7)BEh PP.TCR PP.TIFGC PP.TEPC -- -- -- -- PP.TSR PP.TSRL PP.TSRIE PP.TPCR1 PP.TPCR2 PP.TBCR1 PP.TBCR2 -- -- Packet Processor Transmit Control Register Packet Processor Transmit Inter-Frame Gapping Control Register Packet Processor Transmit Errored Packet Control Register Reserved Reserved Reserved Reserved Packet Processor Transmit Status Register Packet Processor Transmit Status Register Latched Packet Processor Transmit Status Register Interrupt Enable Packet Processor Transmit Packet Count Register 1 Packet Processor Transmit Packet Count Register 2 Packet Processor Transmit Byte Count Register 1 Packet Processor Transmit Byte Count Register 2 Unused Unused 12.14.3.1 Register Bit Descriptions Register Name: Register Description: Register Address: PP.TCR Packet Processor Transmit Control Register (1,3,5,7)A0h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 Reserved 0 10 Reserved 0 9 Reserved 0 8 Reserved 0 Bit # Name Default 7 -- 0 6 -- 0 5 TFAD 0 4 TF16 0 3 TIFV 0 2 TSD 0 1 TBRE 0 0 TPTE 0 Bit 5: Transmit FCS Append Disable (TFAD) - This bit controls whether or not a FCS is appended to the end of each packet. When 0, the calculated FCS bytes are appended to the end of the packet. When 1, the packet is transmitted without a FCS. Bit 4: Transmit FCS-16 Enable (TF16) - When 0, the FCS processing uses a 32-bit FCS. When 1, the FCS processing uses a 16-bit FCS Bit 3: Transmit Bit Synchronous Inter-frame Fill Value (TIFV) - When 0, inter-frame fill is done with the flag sequence (7Eh). When 1, inter-frame fill is done with all '1's. This bit is ignored in octet aligned mode. Bit 2: Transmit Scrambling Disable (TSD) - When 0, scrambling is performed. When 1, scrambling is disabled. Bit 1: Transmit Bit Reordering Enable (TBRE) - When 0, bit reordering is disabled (The first bit transmitted is from the MSB of the transmit FIFO byte). When 1, bit reordering is enabled (The first bit transmitted is from the LSB of the transmit FIFO byte). Bit 0: Transmit Pass-Through Enable (TPTE) - When 0, pass-through mode is disabled and packet processing is enabled. When 1, the packet processor is in pass-through mode and all packet-processing functions except scrambling and bit reordering are disabled. 357 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PP.TIFGC Packet Processor Transmit Inter-Frame Gapping Control Register (1,3,5,7)A2h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 TIFG7 0 6 TIFG6 0 5 TIFG5 0 4 TIFG4 0 3 TIFG3 0 2 TIFG2 0 1 TIFG1 0 0 TIFG0 1 Bits 7 to 0: Transmit Inter-Frame Gapping (TIFG[7:0]) - These eight bits indicate the number of additional flags and bytes of inter-frame fill to be inserted between packets. The number of flags and bytes of inter-frame fill between packets will be at least the value of TIFG[7:0] plus 1. Note: If inter-frame fill is set to all 1's, a TFIG value of 2 or 3 will result in a flag, at least two bytes of 1's, and a flag between packets. Register Name: Register Description: Register Address: PP.TEPC Packet Processor Transmit Errored Packet Control Register (1,3,5,7)A4h Bit # Name Default 15 MEIMS 0 14 TPER6 0 13 TPER5 0 12 TPER4 0 11 TPER3 0 10 TPER2 0 9 TPER1 0 8 TPER0 0 Bit # Name Default 7 TPEN7 0 6 TPEN6 0 5 TPEN5 0 4 TPEN4 0 3 TPEN3 0 2 TPEN2 0 1 TPEN1 0 0 TPEN0 0 Bit 15: Manual Error Insert Mode Select (MEIMS) - When 0, the transmit manual error insertion signal (TMEI) will not cause errors to be inserted. When 1, TMEI will causes an error to be inserted when it transitions from a 0 to a 1. Note: Enabling TMEI does not disable error insertion using TPER[6:0] and TPEN[7:0]. Manual Error Insertion is available at the global level but not on a per-port basis for the packet processor. (PORT.CR1.MEIM must be set for global error insertion to insert a packet error.) Bits 14 to 8: Transmit Errored Packet Insertion Rate (TPER[6:0]) - These seven bits indicate the rate at which errored packets are to be output. One out of every x * 10y packets is to be an errored packet. TPER[3:0] is the value x, and TPER[6:4] is the value y, which has a maximum value of 6. If TPER[3:0] has a value of 0h errored packet insertion is disabled. If TPER[6:4] has a value of 6xh or 7xh the errored packet rate will be x * 106. A TPER[6:0] value of 01h results in every packet being errored. A TPER[6:0] value of 0Fh results in every 15th packet being errored. A TPER[6:0] value of 11h result in every 10th packet being errored. Errored packet insertion starts when the PP.TEPC register is written with a TPER[3:0] value that is non-zero. If the PP.TEPC register is written to during the middle of an errored packet insertion process, the current process is halted, and a new process will be started using the new values of TPER[6:0] and TPEN[7:0}. Errored packet insertion ends when TPEN[7:0] errored packets have been transmitted. Bits 7 to 0: Transmit Errored Packet Insertion Number (TPEN[7:0]) - These eight bits indicate the total number of errored packets to be transmitted. A value of FFh results in continuous errored packet insertion at the specified rate. 358 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PP.TSR Packet Processor Transmit Status Register (1,3,5,7)AEh Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 -- 6 -- 5 -- 4 -- 3 -- 2 -- 1 -- 0 TEPF Bit 0: Transmit Errored Packet Insertion Finished (TEPF) - This bit is set when the number of errored packets indicated by the TPEN[7:0] bits in the PP.TEPC register have been transmitted. This bit is cleared when errored packet insertion is disabled, or a new errored packet insertion process is initiated. Register Name: Register Description: Register Address: PP.TSRL Packet Processor Transmit Status Register Latched (1,3,5,7)B0h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 -- 10 -- 9 -- 8 -- Bit # Name 7 -- 6 -- 5 -- 4 -- 3 -- 2 -- 1 -- 0 TEPFL Bit 0: Transmit Errored Packet Insertion Finished Latched (TEPFL) - This bit is set when the TEPF bit in the PP.TSR register transitions from zero to one. Register Name: Register Description: Register Address: PP.TSRIE Packet Processor Transmit Status Register Interrupt Enable (1,3,5,7)B2h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 -- 0 6 -- 0 5 -- 0 4 -- 0 3 -- 0 2 -- 0 1 -- 0 0 TEPFIE 0 Bit 0: Transmit Errored Packet Insertion Finished Interrupt Enable (TEPFIE) - This bit enables an interrupt if the TEPFL bit in the PP.TSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled 359 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PP.TPCR1 Packet Processor Transmit Packet Count Register 1 (1,3,5,7)B4h Bit # Name Default 15 TPC15 0 14 TPC14 0 13 TPC13 0 12 TPC12 0 11 TPC11 0 10 TPC10 0 9 TPC9 0 8 TPC8 0 Bit # Name Default 7 TPC7 0 6 TPC6 0 5 TPC5 0 4 TPC4 0 3 TPC3 0 2 TPC2 0 1 TPC1 0 0 TPC0 0 Bits 15 to 0: Transmit Packet Count (TPC[15:0]) - Lower 16 bits of 24 bits. Register description follows next register. Register Name: Register Description: Register Address: PP.TPCR2 Packet Processor Transmit Packet Count Register 2 (1,3,5,7)B6h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 TPC23 0 6 TPC22 0 5 TPC21 0 4 TPC20 0 3 TPC19 0 2 TPC18 0 1 TPC17 0 0 TPC16 0 Bits 7 to 0: Transmit Packet Count (TPC[23:16]) - Upper 8 bits of Register. Transmit Packet Count (TPC[23:0]) - These 24 bits indicate the number of packets extracted from the Transmit FIFO and output in the outgoing data stream. This register is updated via the PMU signal (see Section 10.4.5). 360 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PP.TBCR1 Packet Processor Transmit Byte Count Register 1 (1,3,5,7)B8h Bit # Name Default 15 TBC15 0 14 TBC14 0 13 TBC13 0 12 TBC12 0 11 TBC11 0 10 TBC10 0 9 TBC9 0 8 TBC8 0 Bit # Name Default 7 TBC7 0 6 TBC6 0 5 TBC5 0 4 TBC4 0 3 TBC3 0 2 TBC2 0 1 TBC1 0 0 TBC0 0 Bits 15 to 0: Transmit Byte Count (TBC[15:0]) - Lower 16 bits of 32 bits. Register description follows next register. Register Name: Register Description: Register Address: PP.TBCR2 Packet Processor Transmit Byte Count Register 2 (1,3,5,7)BAh Bit # Name Default 15 TBC31 0 14 TBC30 0 13 TBC29 0 12 TBC28 0 11 TBC27 0 10 TBC26 0 9 TBC25 0 8 TBC24 0 Bit # Name Default 7 TBC23 0 6 TBC22 0 5 TBC21 0 4 TBC20 0 3 TBC19 0 2 TBC18 0 1 TBC17 0 0 TBC16 0 Bits 15 to 0: Transmit Byte Count (TBC[31:16]) - Upper 16 bits of 32 bits. Transmit Byte Count (TBC[31:0]) - These 32 bits indicate the number of packet bytes inserted in the outgoing data stream. This register is updated via the PMU signal (see Section 10.4.5). 361 DS3181/DS3182/DS3183/DS3184 12.14.4 Receive Packet Processor Register Map The receive packet processor block has 17 registers. Table 12-51. Receive Packet Processor Register Map ADDRESS REGISTER (1,3,5,7)C0h (1,3,5,7)C2h (1,3,5,7)C4h (1,3,5,7)C6h (1,3,5,7)C8h (1,3,5,7)CAh (1,3,5,7)CCh (1,3,5,7)CEh (1,3,5,7)D0h (1,3,5,7)D2h (1,3,5,7)D4h (1,3,5,7)D6h (1,3,5,7)D8h (1,3,5,7)DAh (1,3,5,7)DCh (1,3,5,7)DEh (1,3,5,7)E0h (1,3,5,7)E2h (1,3,5,7)E4h (1,3,5,7)E6h (1,3,5,7)E8h (1,3,5,7)EAh (1,3,5,7)ECh (1,3,5,7)EEh (1,3,5,7)F0h (1,3,5,7)F2h (1,3,5,7)F4h (1,3,5,7)F6h (1,3,5,7)F8h (1,3,5,7)FAh (1,3,5,7)FCh (1,3,5,7)FEh PP.RCR PP.RMPSC -- -- -- -- -- PP.RSR PP.RSRL PP.RSRIE PP.RPCR1 PP.RPCR2 PP.RFPCR1 PP.RFPCR2 PP.RAPCR1 PP.RAPCR2 PP.RSPCR1 PP.RSPCR2 -- -- PP.RBCR1 PP.RBCR2 PP.REBCR1 PP.REBCR2 -- -- -- -- -- -- -- -- REGISTER DESCRIPTION Packet Processor Receive Control Register Packet Processor Receive Maximum Packet Size Control Register Reserved Reserved Reserved Reserved Reserved Packet Processor Receive Status Register Packet Processor Receive Status Register Latched Packet Processor Receive Status Register Interrupt Enable Packet Processor Receive Packet Count Register 1 Packet Processor Receive Packet Count Register 2 Packet Processor Receive FCS Errored Packet Count Register 1 Packet Processor Receive FCS Errored Packet Count Register 2 Packet Processor Receive Aborted Packet Count Register 1 Packet Processor Receive Aborted Packet Count Register 2 Packet Processor Receive Size Violation Packet Count Register 1 Packet Processor Receive Size Violation Packet Count Register 2 Reserved Reserved Packet Processor Receive Byte Count Register 1 Packet Processor Receive Byte Count Register 2 Packet Processor Receive Errored Byte Count Register 1 Packet Processor Receive Errored Byte Count Register 2 Unused Unused Unused Unused Unused Unused Unused Unused 362 DS3181/DS3182/DS3183/DS3184 12.14.4.1 Register Bit Descriptions Register Name: Register Description: Register Address: PP.RCR Packet Processor Receive Control Register (1,3,5,7)C0h Bit # Name Default 15 RMNS7 0 14 RMNS6 0 13 RMNS5 0 12 RMNS4 0 11 RMNS3 0 10 RMNS2 0 9 RMNS1 0 8 RMNS0 0 Bit # Name Default 7 Reserved 0 6 Reserved 0 5 RFPD 0 4 RF16 0 3 RFED 0 2 RDD 0 1 RBRE 0 0 RPTE 0 Bits 15 to 8: Receive Minimum Packet Size (RMNS[7:0]) - These eight bits indicate the minimum allowable packet size in bytes. The size includes the FCS bytes, but excludes bit/byte stuffing. Note: In FCS-32 mode, packets with six bytes are the minimum packet size allowed, in FCS-16 mode, packets with four bytes are the minimum packet size allowed, and when FCS processing is disabled, packets with two bytes are the minimum packet size allowed. Packets less than the minimum size will be aborted. Bit 5: Receive FCS Processing Disable (RFPD) - When 0, FCS processing is performed (the packets have an FCS appended). When 1, FCS processing is disabled (the packets do not have an FCS appended). Bit 4: Receive FCS-16 Enable (RF16) - When 0, the error checking circuit uses a 32-bit FCS. When 1, the error checking circuit uses a 16-bit FCS. This bit is ignored when FCS processing is disabled. Bit 3: Receive FCS Extraction Disable (RFED) - When 0, the FCS bytes are discarded. When 1, the FCS bytes are passed on. This bit is ignored when FCS processing is disabled. Bit 2: Receive Descrambling Disable (RDD) - When 0, descrambling is performed. When 1, descrambling is disabled. Bit 1: Receive Bit Reordering Enable (RBRE) - When 0, bit reordering is disabled (The first bit received is stored in the MSB of the receive FIFO byte). When 1, bit reordering is enabled (The first bit received is stored in the LSB of the receive FIFO byte). Bit 0: Receive Pass-Through Enable (RPTE) - When 0, pass-through mode is disabled and packet processing is enabled. When 1, pass-through mode is enabled, and all packet-processing functions except descrambling and bit reordering are disabled. Register Name: Register Description: Register Address: PP.RMPSC Packet Processor Receive Maximum Packet Size Control Register (1,3,5,7)C2h Bit # Name Default 15 RMX15 0 14 RMX14 0 13 RMX13 0 12 RMX12 0 11 RMX11 0 10 RMX10 1 9 RMX9 1 8 RMX8 0 Bit # Name Default 7 RMX7 0 6 RMX6 0 5 RMX5 0 4 RMX4 0 3 RMX3 0 2 RMX2 0 1 RMX1 0 0 RMX0 0 Bits 15 to 0: Receive Maximum Packet Size (RMX[15:0]) - These 16 bits indicate the maximum allowable packet size in bytes. The size includes the FCS bytes, but excludes bit/byte stuffing. Note: If the maximum packet length is less than the minimum packet length, all packets will be aborted. When packet processing is disabled, these 16 bits indicate the "packet" size the incoming data is to be broken into. 363 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PP.RSR Packet Processor Receive Status Register (1,3,5,7)CEh Bit # Name 15 -- 14 -- 13 -- 12 -- 11 Reserved 10 Reserved 9 Reserved 8 Reserved Bit # Name 7 -- 6 -- 5 -- 4 -- 3 -- 2 REPC 1 RAPC 0 RSPC Bit 2: Receive FCS Errored Packet Count (REPC) - This read-only bit indicates that the receive FCS errored packet count is non-zero. Bit 1: Receive Aborted Packet Count (RAPC) - This read-only bit indicates that the receive aborted packet count is non-zero. Bit 0: Receive Size Violation Packet Count (RSPC) - This read-only bit indicates that the receive size violation packet count is non-zero. Register Name: Register Description: Register Address: PP.RSRL Packet Processor Receive Status Register Latched (1,3,5,7)D0h Bit # Name 15 -- 14 -- 13 -- 12 -- 11 Reserved 10 Reserved 9 Reserved 8 Reserved Bit # Name 7 REPL 6 RAPL 5 RIPDL 4 RSPDL 3 RLPDL 2 REPCL 1 RAPCL 0 RSPCL Bit 7: Receive FCS Errored Packet Latched (REPL) - This bit is set when a packet with an errored FCS is detected. Bit 6: Receive Aborted Packet Latched (RAPL) - This bit is set when a packet with an abort indication is detected. Bit 5: Receive Invalid Packet Detected Latched (RIPDL) - This bit is set when a packet with a non-integer number of bytes is detected. Bit 4: Receive Small Packet Detected Latched (RSPDL) - This bit is set when a packet smaller than the minimum packet size is detected. Bit 3: Receive Large Packet Detected Latched (RLPDL) - This bit is set when a packet larger than the maximum packet size is detected. Bit 2: Receive FCS Errored Packet Count Latched (REPCL) - This bit is set when the REPC bit in the RPPSR register transitions from zero to one. Bit 1: Receive Aborted Packet Count Latched (RAPCL) - This bit is set when the RAPC bit in the RPPSR register transitions from zero to one. Bit 0: Receive Size Violation Packet Count Latched (RSPCL) - This bit is set when the RSPC bit in the RPPSR register transitions from zero to one. 364 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PP.RSRIE Packet Processor Receive Status Register Interrupt Enable (1,3,5,7)D2h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 Reserved 0 10 Reserved 0 9 Reserved 0 8 Reserved 0 Bit # Name Default 7 REPIE 0 6 RAPIE 0 5 RIPDIE 0 4 RSPDIE 0 3 RLPDIE 0 2 REPCIE 0 1 RAPCIE 0 0 RSPCIE 0 Bit 7: Receive FCS Errored Packet Interrupt Enable (REPIE) - This bit enables an interrupt if the REPL bit in the PP.RSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 6: Receive Aborted Packet Interrupt Enable (RAPIE) - This bit enables an interrupt if the RAPL bit in the PP.RSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 5: Receive Invalid Packet Detected Interrupt Enable (RIPDIE) - This bit enables an interrupt if the RIPDL bit in the PP.RSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 4: Receive Small Packet Detected Interrupt Enable (RSPDIE) - This bit enables an interrupt if the RSPDL bit in the PP.RSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 3: Receive Large Packet Detected Interrupt Enable (RLPDIE) - This bit enables an interrupt if the RLPDL bit in the PP.RSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 2: Receive FCS Errored Packet Count Interrupt Enable (REPCIE) - This bit enables an interrupt if the REPCL bit in the PP.RSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. Must be set low when the packets do not have a FCS appended. 0 = interrupt disabled 1 = interrupt enabled Bit 1: Receive Aborted Packet Count Interrupt Enable (RAPCIE) - This bit enables an interrupt if the RAPCL bit in the PP.RSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled Bit 0: Receive Size Violation Packet Count Interrupt Enable (RSPCIE) - This bit enables an interrupt if the RSPCL bit in the PP.RSRL register is set and the bit in GL.ISRIE.PSRIE[4:1] that corresponds to this port is set. 0 = interrupt disabled 1 = interrupt enabled 365 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PP.RPCR1 Packet Processor Receive Packet Count Register 1 (1,3,5,7)D4h Bit # Name Default 15 RPC15 0 14 RPC14 0 13 RPC13 0 12 RPC12 0 11 RPC11 0 10 RPC10 0 9 RPC9 0 8 RPC8 0 Bit # Name Default 7 RPC7 0 6 RPC6 0 5 RPC5 0 4 RPC4 0 3 RPC3 0 2 RPC2 0 1 RPC1 0 0 RPC0 0 Bits 15 to 0: Receive Packet Count (RPC[15:0]) - Lower 16 bits of 24 bits. Register description follows next register. Register Name: Register Description: Register Address: PP.RPCR2 Packet Processor Receive Packet Count Register 2 (1,3,5,7)D6h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 RPC23 0 6 RPC22 0 5 RPC21 0 4 RPC20 0 3 RPC19 0 2 RPC18 0 1 RPC17 0 0 RPC16 0 Bits 7 to 0: Receive Packet Count (RPC[23:16]) - Upper 8 bits of Register. Receive Packet Count (RPC[23:0]) - These 24 bits indicate the number of packets stored in the receive FIFO without an abort indication. Note: Packets discarded due to system loopback or an overflow condition will be included in this count. This register is updated via the PMU signal (see Section 10.4.5). 366 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PP.RFPCR1 Packet Processor Receive FCS Errored Packet Count Register 1 (1,3,5,7)D8h Bit # Name Default 15 RFPC15 0 14 RFPC14 0 13 RFPC13 0 12 RFPC12 0 11 RFPC11 0 10 RFPC10 0 9 RFPC9 0 8 RFPC8 0 Bit # Name Default 7 RFPC7 0 6 RFPC6 0 5 RFPC5 0 4 RFPC4 0 3 RFPC3 0 2 RFPC2 0 1 RFPC1 0 0 RFPC0 0 Bits 15 to 0: Receive FCS Errored Packet Count (RFPC[15:0]) - Lower 16 bits of 24 bits. Register description follows next register. Register Name: Register Description: Register Address: PP.RFPCR2 Packet Processor Receive FCS Errored Packet Count Register 2 (1,3,5,7)DAh Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 RFPC23 0 6 RFPC22 0 5 RFPC21 0 4 RFPC20 0 3 RFPC19 0 2 RFPC18 0 1 RFPC17 0 0 RFPC16 0 Bits 7 to 0: Receive FCS Errored Packet Count (RFPC[7:0]) Receive FCS Errored Packet Count (RFPC[23:0]) - These 24 bits indicate the number of packets received with a FCS error. The byte count for these packets is included in the receive aborted byte count register PP.REBCR. This register is updated via the PMU signal (see Section 10.4.5). 367 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PP.RAPCR1 Packet Processor Receive Aborted Packet Count Register 1 (1,3,5,7)DCh Bit # Name Default 15 RAPC15 0 14 RAPC14 0 13 RAPC13 0 12 RAPC12 0 11 RAPC11 0 10 RAPC10 0 9 RAPC9 0 8 RAPC8 0 Bit # Name Default 7 RAPC7 0 6 RAPC6 0 5 RAPC5 0 4 RAPC4 0 3 RAPC3 0 2 RAPC2 0 1 RAPC1 0 0 RAPC0 0 Bits 15 to 0: Receive Aborted Packet Count (RAPC[15:0]) - Lower 16 bits of 24 bits. Register description follows next register. Register Name: Register Description: Register Address: PP.RAPCR2 Packet Processor Receive Aborted Packet Count Register 2 (1,3,5,7)DEh Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 RAPC23 0 6 RAPC22 0 5 RAPC21 0 4 RAPC20 0 3 RAPC19 0 2 RAPC18 0 1 RAPC17 0 0 RAPC16 0 Bits 7 to 0: Receive Aborted Packet Count (RAPC[23:16]) - Upper 8 bits of Register. Receive Aborted Packet Count (RAPC[23:0]) - These 24 bits indicate the number of packets received with a packet abort indication. The byte count for these packets is included in the receive aborted byte count register PP.REBCR. This register is updated via the PMU signal (see Section 10.4.5). 368 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PP.RSPCR1 Packet Processor Receive Size Violation Packet Count Register 1 (1,3,5,7)E0h Bit # Name Default 15 RSPC15 0 14 RSPC14 0 13 RSPC13 0 12 RSPC12 0 11 RSPC11 0 10 RSPC10 0 9 RSPC9 0 8 RSPC8 0 Bit # Name Default 7 RSPC7 0 6 RSPC6 0 5 RSPC5 0 4 RSPC4 0 3 RSPC3 0 2 RSPC2 0 1 RSPC1 0 0 RSPC0 0 Bits 15 to 0: Receive Size Violation Packet Count (RSPC[15:0]) - Lower 16 bits of 24 bits. Register description follows next register. Register Name: Register Description: Register Address: PP.RSPCR2 Packet Processor Receive Size Violation Packet Count Register 2 (1,3,5,7)E2h Bit # Name Default 15 -- 0 14 -- 0 13 -- 0 12 -- 0 11 -- 0 10 -- 0 9 -- 0 8 -- 0 Bit # Name Default 7 RSPC23 0 6 RSPC22 0 5 RSPC21 0 4 RSPC20 0 3 RSPC19 0 2 RSPC18 0 1 RSPC17 0 0 RSPC16 0 Bits 7 to 0: Receive Size Violation Packet Count (RSPC[23:16]) - Upper 8 bits of Register. Receive Size Violation Packet Count (RSPC[23:0]) - These 24 bits indicate the number of packets received with a packet size violation (below minimum, above maximum, or non-integer number of bytes). The byte count for these packets is included in the receive aborted byte count register PP.REBCR. 369 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PP.RBCR1 Packet Processor Receive Byte Count Register 1 (1,3,5,7)E8h Bit # Name Default 15 RBC15 0 14 RBC14 0 13 RBC13 0 12 RBC12 0 11 RBC11 0 10 RBC10 0 9 RBC9 0 8 RBC8 0 Bit # Name Default 7 RBC7 0 6 RBC6 0 5 RBC5 0 4 RBC4 0 3 RBC3 0 2 RBC2 0 1 RBC1 0 0 RBC0 0 Bits 15 to 0: Receive Byte Count (RBC[15:0]) - Lower 16 bits of 32 bits. Register description follows next register. Register Name: Register Description: Register Address: PP.RBCR2 Packet Processor Receive Byte Count Register 2 (1,3,5,7)EAh Bit # Name Default 15 RBC31 0 14 RBC30 0 13 RBC29 0 12 RBC28 0 11 RBC27 0 10 RBC26 0 9 RBC25 0 8 RBC24 0 Bit # Name Default 7 RBC23 0 6 RBC22 0 5 RBC21 0 4 RBC20 0 3 RBC19 0 2 RBC18 0 1 RBC17 0 0 RBC16 0 Bits 15 to 0: Receive Byte Count (RBC[31:16]) - Upper 16 bits of 32 bits. Receive Byte Count (RBC[31:0]) - These 32 bits indicate the number of bytes contained in packets stored in the receive FIFO without an error indication. Note: Bytes discarded due to FCS extraction, system loopback, FIFO reset, or an overflow condition may be included in this count. This register is updated via the PMU signal (see Section 10.4.5). 370 DS3181/DS3182/DS3183/DS3184 Register Name: Register Description: Register Address: PP.REBCR1 Packet Processor Receive Errored Byte Count Register 1 (1,3,5,7)ECh Bit # Name Default 15 REBC15 0 14 REBC14 0 13 REBC13 0 12 REBC12 0 11 REBC11 0 10 REBC10 0 9 REBC9 0 8 REBC8 0 Bit # Name Default 7 REBC7 0 6 REBC6 0 5 REBC5 0 4 REBC4 0 3 REBC3 0 2 REBC2 0 1 REBC1 0 0 REBC0 0 Bits 15 to 0: Receive Errored Byte Count (REBC[15:0]) - Lower 16 bits of 32 bits. Register description follows next register. Register Name: Register Description: Register Address: PP.REBCR2 Packet Processor Receive Errored Byte Count Register 2 (1,3,5,7)EEh Bit # Name Default 15 REBC31 0 14 REBC30 0 13 REBC29 0 12 REBC28 0 11 REBC27 0 10 REBC26 0 9 REBC25 0 8 REBC24 0 Bit # Name Default 7 REBC23 0 6 REBC22 0 5 REBC21 0 4 REBC20 0 3 REBC19 0 2 REBC18 0 1 REBC17 0 0 REBC16 0 Bits 15 to 0: Receive Errored Byte Count (REBC[31:16]) - Upper 16 bits of 32 bits. Receive Errored Byte Count (REBC[31:0]) - These 32 bits indicate the number of bytes contained in packets stored in the receive FIFO with an error indication. Note: Bytes discarded due to FCS extraction, system loopback, FIFO reset, or an overflow condition may be included in this count. This register is updated via the PMU signal (see Section 10.4.5). 371 DS3181/DS3182/DS3183/DS3184 13 JTAG INFORMATION 13.1 JTAG Description This device supports the standard instruction codes SAMPLE/PRELOAD, BYPASS, and EXTEST. Optional public instructions included are HIGHZ, CLAMP, and IDCODE. The device contains the following items, which meet the requirements set by the IEEE 1149.1 Standard Test Access Port (TAP) and Boundary Scan Architecture: Test Access Port (TAP) TAP Controller Instruction Register Bypass Register Boundary Scan Register Device Identification Register The Test Access Port has the necessary interface pins, namely JTCLK, JTDI, JTDO, and JTMS, and the optional JTRST input. Details on these pins can be found in Section 8. See IEEE 1149.1-1990, IEEE 1149.1a-1993, and IEEE 1149.1b-1994 for details about the Boundary Scan Architecture and the Test Access Port. Figure 13-1. JTAG Block Diagram Boundary Scan Register Identification Register Mux Bypass Register Instruction Register Select Test Access Port Controller 10K 10K JTDI JTMS Tri-State 10K JTCLK JTRST* 372 JTDO DS3181/DS3182/DS3183/DS3184 13.2 JTAG TAP Controller State Machine Description This section covers the details on the operation of the Test Access Port (TAP) Controller State Machine. See Figure 13-2 for details on each of the states described below. The TAP controller is a finite state machine that responds to the logic level at JTMS on the rising edge of JTCLK. Figure 13-2. JTAG TAP Controller State Machine Test-Logic-Reset 1 0 0 Run-Test/Idle 1 Select DR-Scan 1 0 1 0 1 Capture-DR Capture-IR 0 0 Shift-DR Shift-IR 0 1 1 1 Exit1-IR 0 0 Pause-DR Pause-IR 0 1 0 1 0 Exit2-DR Exit2-IR 1 1 Update-DR 1 0 1 Exit1- DR 0 1 Select IR-Scan 0 Update-IR 1 0 Test-Logic-Reset. When JTRST is changed from low to high, the TAP controller starts in the Test-Logic-Reset state, and the Instruction Register is loaded with the IDCODE instruction. All system logic and I/O pads on the device operate normally. This state can also be reached from any other state by holding JTMS high and clocking JTCLK five times. Run-Test-Idle. Run-Test-Idle is used between scan operations or during specific tests. The Instruction Register and Test Register remain idle. Select-DR-Scan. All test registers retain their previous state. With JTMS low, a rising edge of JTCLK moves the controller into the Capture-DR state and initiates a scan sequence. JTMS high moves the controller to the SelectIR-Scan state. Capture-DR. Data may be parallel loaded into the Test Data register selected by the current instruction. If the instruction does not call for a parallel load or the selected register does not allow parallel loads, the Test Register remains at its current value. On the rising edge of JTCLK, the controller goes to the Shift-DR state if JTMS is low or to the Exit1-DR state if JTMS is high. 373 DS3181/DS3182/DS3183/DS3184 Shift-DR. The Test Data Register selected by the current instruction is connected between JTDI and JTDO and shifts data one stage toward its serial output on each rising edge of JTCLK. If a Test Register selected by the current instruction is not placed in the serial path, it maintains its previous state. Exit1-DR. While in this state, a rising edge on JTCLK with JTMS high puts the controller in the Update-DR state that terminates the scanning process. A rising edge on JTCLK with JTMS low puts the controller in the Pause-DR state. Pause-DR. Shifting of the Test registers is halted while in this state. All Test registers selected by the current instruction retain their previous state. The controller remains in this state while JTMS is low. A rising edge on JTCLK with JTMS high puts the controller in the Exit2-DR state. Exit2-DR. While in this state, a rising edge on JTCLK with JTMS high puts the controller in the Update-DR state and terminate the scanning process. A rising edge on JTCLK with JTMS low puts the controller in the Shift-DR state. Update-DR. A falling edge on JTCLK while in the Update-DR state latches the data from the shift register path of the Test registers into the data output latches. This prevents changes at the parallel output due to changes in the shift register. A rising edge on JTCLK with JTMS low, puts the controller in the Run-Test-Idle state. With JTMS high, the controller enters the Select-DR-Scan state. Select-IR-Scan. All Test registers retain their previous state. The Instruction register remains unchanged during this state. With JTMS low, a rising edge on JTCLK moves the controller into the Capture-IR state and initiates a scan sequence for the Instruction register. JTMS high during a rising edge on JTCLK puts the controller back into the Test-Logic-Reset state. Capture-IR. The Capture-IR state is used to load the shift register in the Instruction register with a fixed value of 001. This value is loaded on the rising edge of JTCLK. If JTMS is high on the rising edge of JTCLK, the controller enters the Exit1-IR state. If JTMS is low on the rising edge of JTCLK, the controller enters the Shift-IR state. Shift-IR. In this state, the shift register in the Instruction register is connected between JTDI and JTDO and shifts data one stage for every rising edge of JTCLK toward the serial output. The parallel registers, as well as all Test registers, remain at their previous states. A rising edge on JTCLK with JTMS high moves the controller to the Exit1IR state. A rising edge on JTCLK with JTMS low keeps the controller in the Shift-IR state while moving data one stage through the Instruction shift register. Exit1-IR. A rising edge on JTCLK with JTMS low puts the controller in the Pause-IR state. If JTMS is high on the rising edge of JTCLK, the controller enters the Update-IR state and terminate the scanning process. Pause-IR. Shifting of the Instruction register is halted temporarily. With JTMS high, a rising edge on JTCLK puts the controller in the Exit2-IR state. The controller remains in the Pause-IR state if JTMS is low during a rising edge on JTCLK. Exit2-IR. A rising edge on JTCLK with JTMS high put the controller in the Update-IR state. The controller loops back to the Shift-IR state if JTMS is low during a rising edge of JTCLK in this state. Update-IR. The instruction shifted into the Instruction shift register is latched into the parallel output on the falling edge of JTCLK as the controller enters this state. Once latched, this instruction becomes the current instruction. A rising edge on JTCLK with JTMS low, puts the controller in the Run-Test-Idle state. With JTMS high, the controller enters the Select-DR-Scan state. 374 DS3181/DS3182/DS3183/DS3184 13.3 JTAG Instruction Register and Instructions The instruction register contains a shift register as well as a latched parallel output and is 3 bits in length. When the TAP controller enters the Shift-IR state, the instruction shift register is connected between JTDI and JTDO. While in the Shift-IR state, a rising edge on JTCLK with JTMS low shifts data one stage toward the serial output at JTDO. A rising edge on JTCLK in the Exit1-IR state or the Exit2-IR state with JTMS high moves the controller to the UpdateIR state. The falling edge of that same JTCLK latches the data in the instruction shift register to the instruction parallel output. Instructions supported by the device and their respective operational binary codes are shown in Table 13-1. Table 13-1. JTAG Instruction Codes INSTRUCTIONS SELECTED REGISTER INSTRUCTION CODES EXTEST IDCODE SAMPLE/PRELOAD CLAMP HIGHZ ---- ---- BYPASS Boundary Scan Device Identification Boundary Scan Bypass Bypass Bypass Bypass Bypass 000 001 010 011 100 101 110 111 SAMPLE/PRELOAD. This is a mandatory instruction for the IEEE 1149.1 specification. This instruction supports two functions. The digital I/Os of the device can be sampled at the boundary scan register without interfering with the normal operation of the device and the boundary scan register can be pre-loaded for the EXTEST instruction. The positive edge of JTCLK in the Capture-DR state samples all digital input pins into the boundary scan register. The boundary scan register is connected between JTDI and JTDO. The data on JTDI pin is clocked into the boundary scan register and the data captured in the Capture-DR state is shifted out the TDO pin in the Shift-DR state. EXTEST. This is a mandatory instruction for the IEEE 1149.1 specification. This instruction allows testing of all interconnections to the device. When the EXTEST instruction is latched in the instruction register, the following actions occur. Once enabled by the Update-IR state, the parallel outputs of all digital output pins are driven according to the values in the boundary scan registers on the positive edge of JTCLK. The boundary scan register is connected between JTDI and JTDO. The positive edge of JTCLK in the Capture-DR state samples all digital input pins into the boundary scan register. The negative edge of JTCLK in the Update-DR state causes all of the digital output pins to be driven according to the values in the boundary scan registers that have been shifted in during the Shift-DR state. The outputs are returned to their normal mode or HIZ mode at the positive edge of JTCLK during the Update-IR state when an instruction other than EXTEST or CLAMP is activated. BYPASS. This is a mandatory instruction for the IEEE 1149.1 specification. When the BYPASS instruction is latched into the parallel instruction register, JTDI connects to JTDO through the 1-bit bypass test register. This allows data to pass from JTDI to JTDO not affecting the device's normal operation. This mode can be used to bypass one or more chips in a system with multiple chips that have their JTAG scan chain connected in series. The chips not in bypass can then be tested with the normal JTAG modes. IDCODE. This is a mandatory instruction for the IEEE 1149.1 specification. When the IDCODE instruction is latched into the parallel instruction register, the identification test register is selected. The device identification code is loaded into the identification register on the rising edge of JTCLK following entry into the Capture-DR state. ShiftDR can be used to shift the identification code out serially through JTDO. During Test-Logic-Reset, the identification code is forced into the instruction register's parallel output. HIGHZ. All digital outputs are placed into a high-impedance state. The bypass register is connected between JTDI and JTDO. The outputs are put into the HIZ mode when the HIZ instruction is loaded in the Update-IR state and on the positive edge of JTCLK. The outputs are returned to their normal mode or driven from the boundary scan register at the positive edge of JTCLK during the Update-IR state when an instruction other than HIZ is activated. CLAMP. All digital output pins output data from the boundary scan parallel output while connecting the bypass register between JTDI and JTDO. The outputs do not change during the CLAMP instruction. If the previous instruction was not EXTEST, the outputs will be driven according to the values in the boundary scan register at the 375 DS3181/DS3182/DS3183/DS3184 positive edge of JTCLK in the Update-IR state. The typical use of this instruction is in a system that has the JTAG scan chain of multiple chips connected in series, and all of the chips have their outputs initialized using the EXTEST mode. Then some of the chips are left initialized using the CLAMP mode and others have their IO controlled using the EXTEST mode. This reduces the size of the scan chain during the partial testing of the system. 13.4 JTAG ID Codes Table 13-2. JTAG ID Codes DS3181 REVISION ID[31:28] Consult factory DEVICE CODE ID[27:12] 0000000001001000 MANUFACTURER'S CODE ID[11:1] 00010100001 REQUIRED ID[0] 1 DS3182 Consult factory 0000000001001001 00010100001 1 DS3183 Consult factory 0000000001001010 00010100001 1 DS3184 Consult factory 0000000001001011 00010100001 1 DEVICE 13.5 JTAG Functional Timing This functional timing for the JTAG circuits shows: * The JTAG controller starting from reset state. * Shifting out the first 4 LSB bits of the IDCODE. * Shifting in the BYPASS instruction (111) while shifting out the mandatory X01 pattern. * Shifting the TDI pin to the TDO pin through the bypass shift register. * An asynchronous reset occurs while shifting. Figure 13-3. JTAG Functional Timing (INST) (STATE) IDCODE Run Test Idle Reset Select DR Scan Capture DR Exit1 DR Shift DR IDCODE BYPASS Update DR Select DR Scan Select IR Scan Capture IR Shift IR Exit1 IR Update IR Select DR Scan Capture DR Shift DR Test Logic Idle JTCLK JTRST JTMS X X JTDI X X JTDO Output Pin X Output pin level change if in "EXTEST" instruction mode 13.6 IO Pins All input, output, and in/out pins are in/out pins in JTAG mode. 376 X DS3181/DS3182/DS3183/DS3184 14 PIN ASSIGNMENT Table 14-1 details the breakdown of the assigned pins for each device. Table 14-1. Pin Assignment Breakdown DS3184 DS3183 DS3182 DS3181 I/O Signals 275 245 215 185 Digital VDD 40 40 40 40 Analog VDD 13 13 13 13 VSS 68 68 68 68 Total 396 assigned pins 366 assigned pins 336 assigned pins 306 assigned pins Figure 14-1. DS3184 Pin Assignments--400-Lead TE-PBGA Note: Green indicates VSS, Red indicates VDD, and Yellow indicates system interface pins. A 1 2 VSS 3 4 RPOS1 VDD_RX3 5 6 RXN3 TXN3 7 8 9 10 B MODE RNEG1 TCLKI1 C GPIO[5] GPIO[6] A[10] TPOS1 D VDD_RX1 A[5] A[9] TNEG1 RXP3 TXP3 TSOFI1 TOHSOF TPDENI1 VDD_JA3 1 TOHCLK1 RPDAT1 TPDAT3 ROHCLK 1 RPDENI1 TCLKO1 TOH1 RCLKO1 ROH1 E A[1] A[4] A[8] JTRST* TOHEN1 F RXN1 RXP1 JTCLK JTMS GPIO[1] G VDD_JA1 A[3] A[7] H A[0] A[2] A[6] JTDO GPIO[2] UNUSED UNUSED 1 3 J TXN1 TXP1 JTDI VDD_TX1 K CLKA RDY* RD* WR* L CLKB CLKC CS* M TXN2 TXP2 TEST* N VDD_TX2 ALE D[6] 11 TSER1 VDD_TX3 RSOFO1 RSER1 ROH3 VDD VDD VDD VSS VSS TSOFO3 TSER3 VDD VDD VDD VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS INT* WIDTH UNUSED UNUSED 2 4 VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VDD VDD VDD VSS VSS VSS VSS VDD VDD VSS VDD VDD D[11] VDD_JA2 D[12] GPIO[4] VDD VDD VDD VSS VSS VSS D[13] GPIO[3] VDD VDD VDD VSS VSS VSS T VDD_RX2 D[3] D[8] D[14] Y VSS D[5] ROHSOF 2 20 VSS D[15] VDD_CLA D D[7] VDD 19 TEN* VSS HIZ* W 18 TADR[0] VSS D[2] D[4] 17 TPRTY VDD RXP2 GPIO[8] 16 TADR[1] VDD D[0] D[1] 15 RNEG3 VDD RXN2 GPIO[7] 14 RPOS3 RST* TMOD[0] TMOD[1] TDATA[9] VDD TDATA[21 TDATA[19 TDATA[20 TDATA[25 TPOS3 TADR[4] ] ] ] ] TDATA[8] ROHSOF TDATA[22 TDATA[26 TDATA[27 TOH3 TSOFI3 TPDENI3 3 TADR[3] ] ] ] TDXA[4] TDXA[2] TOHSOF ROHCLK TDATA[23 RDATA[2 RDATA[2 TOHCLK3 3 3 TOHEN3 TADR[2] ] 7] 0] TDXA[3] RDXA[4] RDATA[3 RDATA[2 TDATA[24 VSS VSS VDD VDD VDD 1] 6] RDXA[3] RDXA[2] ] RDATA[3 RDATA[2 RDATA[1 RDATA[1 VSS VSS VDD VDD VDD 0] 5] REN* 9] 7] RDATA[2 RDATA[2 RDATA[2 RDATA[1 RDATA[1 VSS VSS VDD VDD VDD 9] 4] 2] 8] 6] RDATA[2 RDATA[2 RDATA[2 VSS VSS VSS VSS VSS 8] 3] 1] RERR TSCLK TLCLK3 P V 13 TSOFO1 TLCLK1 R U 12 TPDENO 1 RPDAT3 RCLKO3 RLCLK3 TCLKO3 TCLKI3 TPDENO RLCLK1 TPDAT1 3 RSER3 RSOFO3 RPDENI3 TNEG3 VDD ROHSOF 1 VSS VDD VDD TOHSOF ROHCLK TOHCLK4 4 4 TOHEN4 ROHSOF TOH4 TSOFI4 TPDENI4 4 TOHEN2 TSER2 VDD_TX4 RSOFO2 RSER2 ROH4 ROHCLK D[9] TNEG2 2 RPDENI2 TCLKO2 TOH2 RCLKO2 ROH2 TOHSOF D[10] TPOS2 TPDENI2 VDD_JA4 2 TOHCLK2 RPDAT2 TPDAT4 TLCLK4 TSOFO4 TSER4 TPOS4 TPDENO RNEG2 TCLKI2 RXP4 TXP4 TSOFI2 RLCLK2 TPDAT2 4 RSER4 RSOFO4 RPDENI4 TNEG4 TPDENO RPOS2 VDD_RX4 RXN4 TXN4 TSOFO2 TLCLK2 2 RPDAT4 RCLKO4 RLCLK4 TCLKO4 TCLKI4 377 TSPA TDXA[1] RVAL RDXA[1] RPRTY REOP RSOX RMOD[0] RMOD[1] RDATA[0] RDATA[1 RDATA[1 5] 1] RDATA[2] RDATA[1] RSCLK RDATA[1 RDATA[1 VDD 4] 0] RDATA[5] RDATA[4] RDATA[3] RDATA[1 VDD 3] RDATA[9] RDATA[8] RDATA[7] RDATA[6] RDATA[1 TDATA[16 VDD 2] ] RADR[2] RADR[1] RADR[0] TDATA[30 TDATA[17 TDATA[18 ] ] ] TDATA[1] RADR[4] RADR[3] TDATA[31 TDATA[29 TDATA[28 ] ] ] TDATA[6] TDATA[3] TDATA[0] TDATA[15 TDATA[12 TEOP ] ] TDATA[5] TDATA[4] TDATA[2] TDATA[14 TDATA[11 TDATA[10 RPOS4 TSOX ] ] ] TDATA[7] TDATA[13 RNEG4 TSX TERR ] VDD VSS VSS DS3181/DS3182/DS3183/DS3184 Figure 14-2. DS3183 Pin Assignments--400-Lead TE-PBGA Note: Green indicates VSS, Red indicates VDD, Yellow indicates system interface pins, and blank cells indicate no connect balls. 1 A VSS B MODE 2 3 4 VDD RPOS1 VDD_RX3 ROHSOF 1 RNEG1 TCLKI1 5 6 RXN3 TXN3 RXP3 TXP3 15 16 17 18 19 20 TSOFO1 TLCLK1 7 8 9 10 11 12 13 14 RNEG3 TADR[1] TPRTY TADR[0] TEN* VSS RPOS3 TPDENO 1 RPDAT3 RCLKO3 RLCLK3 TCLKO3 TCLKI3 TPDENO RLCLK1 TPDAT1 3 RSER3 RSOFO3 RPDENI3 TNEG3 C GPIO[5] GPIO[6] A[10] TPOS1 D VDD_RX1 A[5] A[9] TNEG1 TSOFI1 TOHSOF TPDENI1 VDD_JA3 1 TOHCLK1 RPDAT1 TPDAT3 ROHCLK 1 RPDENI1 TCLKO1 TOH1 RCLKO1 ROH1 E A[1] A[4] A[8] JTRST* TOHEN1 F RXN1 RXP1 JTCLK JTMS GPIO[1] VDD VDD G VDD_JA1 A[3] A[7] JTDO GPIO[2] VDD VDD VDD VDD VDD VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS H A[0] A[2] A[6] J TXN1 TXP1 JTDI VDD_TX1 K CLKA RDY* RD* WR* D[15] VDD_CLA D INT* WIDTH TSER1 VDD_TX3 RSOFO1 RSER1 ROH3 VDD VSS VSS VDD VSS VSS RST* TMOD[0] TMOD[1] TDATA[9] VDD TDATA[21 TDATA[19 TDATA[20 TDATA[25 ] ] TDATA[8] TLCLK3 TSOFO3 TSER3 TPOS3 TADR[4] ] ] ROHSOF TDATA[22 TDATA[26 TDATA[27 ] TOH3 TSOFI3 TPDENI3 3 TADR[3] ] ] TDXA[4] TDXA[2] TOHSOF ROHCLK TDATA[23 RDATA[2 RDATA[2 0] TDXA[3] RDXA[4] TOHCLK3 3 3 TOHEN3 TADR[2] ] 7] RDATA[3 RDATA[2 TDATA[24 VSS VSS VDD VDD VDD 1] 6] RDXA[3] RDXA[2] ] RDATA[3 RDATA[2 RDATA[1 RDATA[1 VSS VSS VDD VDD VDD 0] 5] REN* 9] 7] RDATA[2 RDATA[2 RDATA[2 RDATA[1 RDATA[1 2] 8] 6] VSS VSS VDD VDD VDD 9] 4] RDATA[2 RDATA[2 RDATA[2 1] RERR TSCLK VSS VSS VSS VSS VSS 8] 3] L CLKB CLKC CS* M TXN2 TXP2 TEST* N VDD_TX2 ALE D[6] D[11] VDD_JA2 VDD VDD VDD VSS VSS VSS VSS VDD VDD P D[0] D[2] D[7] D[12] GPIO[4] VDD VDD VDD VSS VSS VSS VSS VDD VDD R RXN2 RXP2 HIZ* D[13] GPIO[3] VDD VDD VDD VSS VSS VSS VSS VDD VDD T VDD_RX2 D[3] D[8] D[14] U D[1] D[4] D[9] TNEG2 V GPIO[7] GPIO[8] D[10] TPOS2 TOHEN2 TSER2 RSOFO2 RSER2 ROHCLK 2 RPDENI2 TCLKO2 TOH2 RCLKO2 TOHSOF TPDENI2 2 TOHCLK2 RPDAT2 W VDD TCLKI2 TSOFI2 Y VSS D[5] RNEG2 ROHSOF 2 RPOS2 ROH2 RLCLK2 TPDAT2 TPDENO TSOFO2 TLCLK2 2 TSPA TDXA[1] RVAL RDXA[1] RPRTY REOP RSOX RMOD[0] RMOD[1] RDATA[0] RDATA[1 RDATA[1 5] 1] RDATA[2] RDATA[1] RSCLK RDATA[1 RDATA[1 VDD 4] 0] RDATA[5] RDATA[4] RDATA[3] RDATA[1 VDD 3] RDATA[9] RDATA[8] RDATA[7] RDATA[6] RDATA[1 TDATA[16 VDD 2] ] RADR[2] RADR[1] RADR[0] TDATA[30 TDATA[17 TDATA[18 ] ] ] TDATA[1] RADR[4] RADR[3] TDATA[31 TDATA[29 TDATA[28 ] ] ] TDATA[6] TDATA[3] TDATA[0] TDATA[15 TDATA[12 TEOP ] ] TDATA[5] TDATA[4] TDATA[2] TDATA[14 TDATA[11 TDATA[10 ] ] TDATA[7] TSOX ] TDATA[13 ] TSX TERR VDD VSS VSS Figure 14-3. DS3182 Pin Assignments--400-Lead TE-PBGA Note: Green indicates VSS, Red indicates VDD, Yellow indicates system interface pins, and blank cells indicate no connect balls. 1 2 3 A VSS RPOS1 B MODE VDD ROHSOF 1 4 5 6 RNEG1 C GPIO[5] GPIO[6] A[10] TPOS1 D VDD_RX1 A[5] A[9] TNEG1 TPDENI1 ROHCLK 1 RPDENI1 TCLKO1 E A[1] A[4] A[8] JTRST* TOHEN1 TSER1 TCLKI1 7 8 TSOFO1 TLCLK1 9 TPDENO 1 10 11 12 13 14 TSOFI1 RLCLK1 TPDAT1 TOHSOF 1 TOHCLK1 RPDAT1 TOH1 RCLKO1 RSOFO1 RSER1 ROH1 F RXN1 RXP1 JTCLK JTMS GPIO[1] VDD VDD VDD VSS VSS VSS VSS VDD VDD G VDD_JA1 A[3] A[7] JTDO GPIO[2] VDD VDD VDD VSS VSS VSS VSS VDD VDD H A[0] A[2] A[6] VDD VDD VDD VSS VSS VSS VSS VDD VDD 15 J TXN1 TXP1 JTDI VDD_TX1 VSS VSS VSS VSS VSS VSS VSS VSS RDY* RD* WR* D[15] VDD_CLA D VSS CLKA VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS INT* WIDTH VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VDD VDD VDD VSS VSS VSS VSS VDD VDD L CLKB CLKC CS* TXN2 TXP2 TEST* N VDD_TX2 ALE D[6] D[11] VDD_JA2 P D[0] D[2] D[7] D[12] GPIO[4] VDD VDD VDD VSS VSS VSS VSS VDD VDD R RXN2 RXP2 HIZ* D[13] GPIO[3] VDD VDD VDD VSS VSS VSS VSS VDD VDD T VDD_RX2 D[3] D[8] D[14] U D[1] D[4] D[9] TNEG2 V GPIO[7] GPIO[8] D[10] TPOS2 TOHEN2 TSER2 RSOFO2 RSER2 ROHCLK 2 RPDENI2 TCLKO2 TOH2 RCLKO2 TOHSOF TPDENI2 2 TOHCLK2 RPDAT2 W VDD RNEG2 TCLKI2 TSOFI2 RLCLK2 Y VSS D[5] ROHSOF 2 TSOFO2 TLCLK2 RPOS2 ROH2 TPDAT2 TPDENO 2 378 17 18 19 20 TPRTY TADR[0] TEN* VSS TMOD[0] TDATA[19 ] TDATA[26 ] RDATA[2 7] RDATA[2 6] RDATA[2 5] RDATA[2 4] RDATA[2 3] TMOD[1] TDATA[20 ] TDATA[27 ] RDATA[2 0] TDXA[1] RVAL RST* TDATA[21 TADR[4] ] TDATA[22 TADR[3] ] TDATA[23 TADR[2] ] RDATA[3 VDD 1] RDATA[3 VDD 0] RDATA[2 VDD 9] RDATA[2 VSS 8] K M 16 TADR[1] TSPA REOP RDATA[1 5] RDATA[1 VDD 4] RDATA[1 VDD 3] RDATA[1 VDD 2] TDATA[30 TDATA[17 ] ] TDATA[31 TDATA[29 ] ] TDATA[15 TEOP ] VSS TDATA[9] VDD TDATA[25 ] TDATA[8] TDXA[4] TDXA[2] TDXA[3] RDXA[4] TDATA[24 RDXA[3] RDXA[2] ] RDATA[1 RDATA[1 REN* 9] 7] RDATA[2 RDATA[1 RDATA[1 2] 8] 6] RDATA[2 1] RERR TSCLK RDXA[1] RPRTY RSOX RMOD[0] RMOD[1] RDATA[0] RDATA[1 1] RDATA[2] RDATA[1] RSCLK RDATA[1 0] RDATA[5] RDATA[4] RDATA[3] TSOX RDATA[9] TDATA[16 ] TDATA[18 ] TDATA[28 ] TDATA[12 ] TDATA[14 ] TSX TERR RDATA[8] RDATA[7] RDATA[6] RADR[1] RADR[0] TDATA[1] RADR[4] RADR[2] RADR[3] TDATA[6] TDATA[3] TDATA[0] TDATA[5] TDATA[4] TDATA[2] TDATA[11 TDATA[10 ] ] TDATA[7] TDATA[13 ] VDD VSS DS3181/DS3182/DS3183/DS3184 Figure 14-4. DS3181 Pin Assignments--400-Lead TE-PBGA Note: Green indicates VSS, Red indicates VDD, Yellow indicates system interface pins, and blank cells indicate no connect balls. A 1 2 3 VSS RPOS1 4 5 6 7 8 TSOFO1 TLCLK1 9 TPDENO 1 B MODE VDD ROHSOF 1 RNEG1 TCLKI1 C GPIO[5] GPIO[6] A[10] TPOS1 D VDD_RX1 A[5] A[9] TNEG1 TSOFI1 RLCLK1 TPDAT1 TOHSOF TPDENI1 1 TOHCLK1 RPDAT1 ROHCLK 1 RPDENI1 TCLKO1 TOH1 RCLKO1 10 11 12 13 14 15 ROH1 A[1] A[4] A[8] JTRST* TOHEN1 TSER1 RSOFO1 RSER1 RXN1 RXP1 JTCLK JTMS GPIO[1] VDD VDD VDD VSS VSS VSS VSS VDD VDD G VDD_JA1 A[3] A[7] JTDO GPIO[2] VDD VDD VDD VSS VSS VSS VSS VDD VDD VDD VDD VDD VSS VSS VSS VSS VDD VDD VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VDD VDD VDD VSS VSS VSS VSS VDD VDD A[0] A[2] A[6] TXN1 TXP1 JTDI VDD_TX1 K CLKA RDY* RD* WR* D[15] VDD_CLA D L CLKB CLKC CS* INT* WIDTH M TXN2 TXP2 TEST* ALE D[6] D[11] N P D[0] D[2] R T D[7] D[12] GPIO[4] VDD VDD VDD VSS VSS VSS VSS VDD VDD HIZ* D[13] GPIO[3] VDD VDD VDD VSS VSS VSS VSS VDD VDD D[14] D[3] D[8] U D[1] D[4] D[9] V GPIO[7] GPIO[8] D[10] W VDD D[5] Y VSS 18 19 20 TADR[0] TEN* VSS TMOD[0] TDATA[19 ] TDATA[26 ] RDATA[2 7] RDATA[2 6] RDATA[2 5] RDATA[2 4] RDATA[2 3] TMOD[1] TDATA[20 ] TDATA[27 ] RDATA[2 0] TDXA[1] RVAL RST* TDATA[21 ] TDATA[22 TADR[3] ] TDATA[23 TADR[2] ] RDATA[3 VDD 1] RDATA[3 VDD 0] RDATA[2 VDD 9] RDATA[2 VSS 8] F J 17 TPRTY TADR[4] E H 16 TADR[1] 379 TSPA REOP RDATA[1 5] RDATA[1 VDD 4] RDATA[1 VDD 3] RDATA[1 VDD 2] TDATA[30 TDATA[17 ] ] TDATA[31 TDATA[29 ] ] TDATA[15 TEOP ] VSS TDATA[9] VDD TDATA[25 ] TDATA[8] TDXA[4] TDXA[2] TDXA[3] RDXA[4] TDATA[24 RDXA[2] ] RDATA[1 RDATA[1 REN* 9] 7] RDATA[2 RDATA[1 RDATA[1 2] 8] 6] RDATA[2 1] RERR TSCLK RDXA[3] RDXA[1] RPRTY RSOX RMOD[0] RMOD[1] RDATA[0] RDATA[1 1] RDATA[2] RDATA[1] RSCLK RDATA[1 0] RDATA[5] RDATA[4] RDATA[3] TSOX RDATA[9] TDATA[16 ] TDATA[18 ] TDATA[28 ] TDATA[12 ] TDATA[14 ] TSX TERR RDATA[8] RDATA[7] RDATA[6] RADR[2] RADR[1] RADR[0] TDATA[1] RADR[4] RADR[3] TDATA[6] TDATA[3] TDATA[0] TDATA[5] TDATA[4] TDATA[2] TDATA[11 TDATA[10 ] ] TDATA[7] TDATA[13 ] VDD VSS DS3181/DS3182/DS3183/DS3184 15 PACKAGE INFORMATION (The package drawing(s) in this data sheet may not reflect the most current specifications. The package number provided for each package is a link to the latest package outline information.) 15.1 400-Lead TE-PBGA (27mm x 27mm, 1.27mm Pitch) (56-G6003-003) 380 DS3181/DS3182/DS3183/DS3184 16 PACKAGE THERMAL INFORMATION The 36 thermal VSS balls in the center 6X6 matrix must be thermally and electrically connected to the internal GND plane of the PC board to achieve these thermal characteristics. PARAMETER VALUE Target Ambient Temperature Range -40C to +85C Die Junction Temperature Range -40 to +125C Theta-JA, Still Air 12.6 C/W (Note 1) Note 1: Theta-JA is based on the package mounted on a 4-layer JEDEC board and measured in a JEDEC test chamber. 381 DS3181/DS3182/DS3183/DS3184 17 DC ELECTRICAL CHARACTERISTICS ABSOLUTE MAXIMUM RATINGS Voltage Range on Any Input, Bidirectional, or Open-Drain Output Lead with Respect to VSS......................................................................................-0.3V to +5.5V Supply Voltage (VDD) with Respect to VSS..............................................................................-0.3V to +3.63V Ambient Operating Temperature Range................................................................................-40C to +85C Junction Operating Temperature Range..............................................................................-40C to +125C Storage Temperature Range.............................................................................................-55C to +125C Soldering Temperature Range..........................................................See IPC/JEDEC J-STD-020 Specification These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time can affect device reliability. Ambient Operating Temperature Range is assuming the device is mounted on a JEDEC standard test board in a convection cooled JEDEC test enclosure. Note: The typical values listed below are not production tested. Table 17-1. Recommended DC Operating Conditions (VDD = 3.3V 5%, Tj = -40C to +85C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS Logic 1 VIH 2.0 5.5 V Logic 0 VIL -0.3 +0.8 V Supply 5% VDD 3.135 3.300 3.465 V MIN TYP MAX UNITS 760 850 610 448 280 130 96 64 32 Table 17-2. DC Electrical Characteristics (Tj = -40C to +85C) PARAMETER Supply Current (VDD = 3.465V) (Notes 1, 2) SYMBOL IDD CONDITIONS DS3184 DS3183 DS3182 DS3181 DS3184 DS3183 DS3182 DS3181 88 mA Power-Down Current (All DISABLE Bits Set) (Note 2) IDDD Lead Capacitance CIO Input Leakage IIL -10 +10 A Input Leakage (Input Pins with Internal Pullup Resistors) IILP -350 +10 A Output Leakage (when High Impedance) ILO -10 +10 A Output Voltage (IOH = -4.0mA) VOH 4mA outputs Output Voltage (IOL = +4.0mA) VOL 4mA outputs Output Voltage (IOH = -6.0mA) VOH 6mA outputs Output Voltage (IOL = +6.0mA) VOL 6mA outputs 7 382 pF 2.4 V 0.4 2.4 Note 1: Mode: STS-1 data rate, transmitting all ones on the LIU, all clocks = 52MHz, digital outputs without load. Note 2: All outputs loaded with rated capacitance; all inputs between VDD and VSS; inputs with pullups connected to VDD. mA V V 0.4 V DS3181/DS3182/DS3183/DS3184 Table 17-3. Output Pin Drive PIN NAME TYPE DRIVE STRENGTH (mA) TLCLKn TPOSn /TDATn TNEGn/TOHMOn TXPn TXNn TOHCLKn TOHSOFn ROHn ROHCLKn ROHSOFn TPOHCLKn/ TCLKOn/TGCLKn TPOHSOFn/TSOFOn/ TDENn/TFOHENOn TPDATn TPDENOn RPOHn/RSERn RPOHCLKn/ RCLKOn/RGCLKn RPOHSOFn/RSOFOn/ RDENn/RFOHENOn TDXA[1]/TPXA TDXA[4:2] TSPA RDATA[31:0] RPRTY RDXA[1]/RPXA/RSX RDXA[4:2] RSOX REOP RVAL RMOD[1:0] RERR D[15:0] RDY INT GPIO[7:0] JTDO CLKB CLKC O O O O O O O O O O 6 6 6 N/A (analog) N/A (analog) 4 4 4 4 4 O 6 O 6 O O O 6 6 6 O 6 O 6 Oz O Oz Oz O Oz O Oz Oz Oz Oz Oz IO Oz Oz IO Oz IO IO 6 6 6 6 6 6 6 6 6 6 6 6 4 6 6 4 4 6 6 383 DS3181/DS3182/DS3183/DS3184 18 AC TIMING CHARACTERISTICS There are several common AC characteristic definitions. These generic definitions are shown below in Figure 18-1, Figure 18-2, Figure 18-3, and Figure 18-4. Definitions that are specific to a given interface are shown in that interface's subsection. Figure 18-1. Clock Period and Duty Cycle Definitions t1 Clock t2 t2 Figure 18-2. Rise Time, Fall Time, and Jitter Definitions t1 t4/2 Clock t3 t3 Figure 18-3. Hold, Setup, and Delay Definitions (Rising Clock Edge) Clock t5 t6 Din t7 Dout 384 t4 DS3181/DS3182/DS3183/DS3184 Figure 18-4. Hold, Setup, and Delay Definitions (Falling Clock Edge) Clock t5 t6 Din t7 Dout Figure 18-5. To/From High-Z Delay Definitions (Rising Clock Edge) Clock t8 t9 Dout Figure 18-6. To/From High-Z Delay Definitions (Falling Clock Edge) Clock t8 t9 Dout 385 DS3181/DS3182/DS3183/DS3184 18.1 Fractional Port Characteristics All AC timing characteristics are specified with a 25 pF capacitive load on all output pins, VIH = 2.4V and VIL = 0.8V. The voltage threshold for all timing measurements is VDD/2. The generic timing definitions shown in Figure 18-1, Figure 18-2, Figure 18-3, and Figure 18-6 apply to this interface. Table 18-1. Fractional Port Timing (VDD = 3.3V 5%, Tj = -40C to +85C.) PARAMETER SYMBOL CLK Period CONDITIONS MIN t1 (Note 1) 19.23 t2/t1 (Note 2) 40 CLK Rise or Fall times (20% to 80%) t3 (Note 2) DIN to CLK Setup Time t5 CLK to DIN Hold Time t6 CLK to DOUT Delay t7 CLK Clock Duty Cycle (t2/t1) TYP MAX UNITS ns 50 60 % 4 ns (Note 3) 3 ns (Note 4) 7 ns (Note 3) 1 ns (Note 4) 1 ns (Note 5) 2 11 ns (Note 6) 2 9 ns Note 1: Any mode, 52MHz TCLKIn, RLCLKn input clocks. Note 2: Any mode, TCLKIn, RLCLKn input clocks. Note 3: TCLKIn, RLCLKn clock inputs to TOHMIn/TSOFIn, TFOHn/TSERn, TFOHENIn, RFOHENIn inputs. Note 4: TCLKOn, RCLKOn clock outputs to TOHMIn/TSOFIn, TFOHn/TSERn, TFOHENOn, RFOHENOn inputs. Note 5: TCLKIn, RLCLKn clock input to TSOFOn/TDENn, RSERn, RSOFOn/RDENn, TPDENOn, TPDATn, and RPDATn outputs. Note 6: TCLKOn, RCLKOn clock output to TSOFOn/TDENn, RSERn, RSOFOn/RDENn, TPDENOn, TPDATn and RPDATn outputs. 18.2 Line Interface AC Characteristics All AC timing characteristics are specified with a 25 pF capacitive load on all output pins, VIH = 2.4V and VIL = 0.8V. The voltage threshold for all timing measurements is VDD/2. The generic timing definitions shown in Figure 18-1, Figure 18-2, Figure 18-3, and Figure 18-6 apply to this interface. Table 18-2. Line Interface Timing (VDD = 3.3V 5%, Tj = -40C to +85C.) PARAMETER CLK Period SYMBOL CONDITIONS MIN TYP MAX UNITS t1 (Note 1) 19.23 t2/t1 (Note 2) 40 CLK Rise or Fall times (20% to 80 %) t3 (Note 2) DIN to CLK Setup Time t5 (Note 3) 4 ns CLK to DIN Hold Time t6 (Note 3) 0 ns CLK to DOUT Delay t7 (Note 4) 2 10 ns (Note 5) 2 8 ns CLK Clock Duty Cycle (t2/t1) Note 1: Any mode, 52MHz TCLKIn, RLCLKn input clocks. Note 2: Any mode, TCLKIn, RLCLKn input clocks. Note 3: RLCLKn clock inputs to RPOSn/RDATn, RNEGn/RLCVn/ROHMIn inputs. Note 4: TCLKIn, RLCLKn clock input to TPOSn/TDATn, TNEGn/TOHMOn outputs. Note 5: TLCLKn, TCLKOn, RCLKOn clock output to TPOSn/TDATn, TNEGn/TOHMOn outputs. 386 ns 50 60 % 4 ns DS3181/DS3182/DS3183/DS3184 18.3 Miscellaneous Pin AC Characteristics All AC timing characteristics are specified with a 25 pF capacitive load on all output pins, VIH = 2.4V and VIL = 0.8V. The voltage threshold for all timing measurements is VDD/2. The generic timing definitions shown in Figure 18-1 and Figure 18-2 apply to this interface. Table 18-3. Miscellaneous Pin Timing (VDD = 3.3V 5%, Tj = -40C to +85C.) PARAMETER SYMBOL CONDITIONS Asynchronous Input High, Low Time t1, t2 (Note 1) Asynchronous Input Rise, Fall Time t3 (Note 1) MIN TYP MAX 500 UNITS ns 10 ns Note 1: TMEI (GPIO), PMU (GPIO), 8KREFI(GPIO) and RST inputs. 18.4 Overhead Port AC Characteristics All AC timing characteristics are specified with a 25 pF capacitive load on all output pins, VIH = 2.4V and VIL = 0.8. The voltage threshold for all timing measurements is VDD/2. The generic timing definitions shown in Figure 18-1, Figure 18-2, Figure 18-3, and Figure 18-6 apply to this interface. Table 18-4. Overhead Port Timing (VDD = 3.3V 5%, Tj = -40C to +125C.) PARAMETER CLK Period SYMBOL CONDITIONS MIN TYP MAX UNITS t1 (Note 1) 500 ns t1, t2 (Note 1) 200 ns DIN to CLK Setup Time t5 (Note 2) 20 ns CLK to DIN Hold Time t6 (Note 2) 20 ns CLK to DOUT Delay t7 (Note 3) -20 CLK Clock High and Low Time 20 ns Note 1: TOHCLKn, TPOHCLKn, ROHCLKn, RPOHCLKn output clocks. Note 2: TOHCLKn, TPOHCLKn clock falling edge outputs to TOHn, TOHENn, TPOHn, TPOHENn inputs. Note 3: TOHCLKn, TPOHCLKn, ROHCLKn, RPOHCLKn clock falling edge outputs to TOHSOFn, TPOHSOFn, ROHn, ROHSOF, RPOHn, RPOHSOFn outputs. 387 DS3181/DS3182/DS3183/DS3184 18.5 System Interface AC Characteristics The AC characteristics of the system interface depend upon the mode of the interface. While UTOPIA vs. POSPHY mode does not have an effect on the AC characteristics, L2 vs. L3 does. Therefore, there are two tables: one for L2 (Table 18-5) and one for L3 (Table 18-6). The generic timing definitions shown in Figure 18-1, Figure 18-2, Figure 18-3, and Figure 18-6 apply to this interface. Table 18-5. System Interface L2 Timing (VDD = 3.3V 5%, Tj = -40C to +125C.) SIGNAL NAME(S) SYMBOL DESCRIPTION RSCLK and TSCLK f1 RSCLK and TSCLK t2/t1 RSCLK and TSCLK t3 Rise/fall times (Notes 1, 2) RADR and REN t5 Hold time from RSCLK (Note 1) RADR and REN t6 MIN Clock frequency (1/t1) (Note 1) 0 Clock duty cycle (Note 1) 40 TYP 50 MAX UNITS 52 MHz 60 % 2 ns 0 ns Setup time to RSCLK (Note 1) 3.5 ns t7 Delay from RSCLK (Notes 1, 3) 2 12 ns t8 From high-Z delay from RSCLK (Notes 1, 3) 2 12 ns t9 To high-Z delay from RSCLK (Notes 1, 3) 2 15 ns t5 Hold time from TSCLK (Note 1) 0 ns t6 Setup time to TSCLK (Note 1) 3.5 ns t7 Delay from TSCLK (Notes 1, 3) 2 12 ns TPXA and TSPA t8 From high-Z delay from TSCLK (Notes 1, 3) 2 12 ns TPXA and TSPA t9 To high-Z delay from TSCLK (Notes 1, 3) 2 15 ns RDATA, RPRTY, RPXA, RSOX, REOP, RVAL, RMOD, and RERR RDATA, RPRTY, RPXA, RSOX, REOP, RVAL, RMOD, and RERR RDATA, RPRTY, RPXA, RSOX, REOP, RVAL, RMOD, and RERR TDATA, TPRTY, TADR, TEN, TSOX, TEOP, TMOD, and TERR TDATA, TPRTY, TADR, TEN, TSOX, TEOP, TMOD, and TERR TPXA and TSPA Note 1: Note 2: Note 3: The input/output timing reference level for all signals is VDD/2. Rise and fall times are measured at output side with the output unloaded. Rise time is measured from 20% to 80% VOH. Fall time is measured from 80% to 20% VOH. These times are met with a 30pF, 300 load on the associated output pin. 388 DS3181/DS3182/DS3183/DS3184 Table 18-6. System Interface L3 Timing (VDD = 3.3V 5%, Tj = -40C to +125C.) SIGNAL NAME(S) SYMBOL DESCRIPTION RSCLK and TSCLK f1 RSCLK and TSCLK t2/t1 RSCLK and TSCLK t3 Rise/fall times (Notes 1, 2) RADR and REN t5 Hold time from RSCLK (Note 1) RADR and REN t6 RDATA, RPRTY, RPXA, RSOX, REOP, RVAL, RMOD, and RERR TDATA, TPRTY, TADR, TEN, TSOX, TEOP, TMOD, and TERR TDATA, TPRTY, TADR, TEN, TSOX, TEOP, TMOD, and TERR TPXA and TSPA Note 1: Note 2: Note 3: MIN Clock frequency (1/t1) (Note 1) 0 Clock duty cycle (Note 1) 40 TYP 50 MAX UNITS 66 MHz 60 % 2 ns 0 ns Setup time to RSCLK (Note 1) 3.5 ns t7 Delay from RSCLK (Notes 1, 3) 2 t5 Hold time from TSCLK (Note 1) 0 ns t6 Setup time to TSCLK (Note 1) 3.5 ns t7 Delay from TSCLK (Notes 1, 3) 2 9.5 9.5 ns ns The input/output timing reference level for all signals is VDD/2. Rise and fall times are measured at output side with the output unloaded. Rise time is measured from 20% to 80% VOH. Fall time is measured from 80% to 20% VOH. These times are met with a 30pF, 300 load on the associated output pin. 389 DS3181/DS3182/DS3183/DS3184 18.6 Micro Interface AC Characteristics The AC characteristics for the external bus interface. This table references Figure 18-7and Figure 18-8. Table 18-7. Micro Interface Timing (VDD = 3.3 5%, Tj = -40C to +125C.) SIGNAL NAME(S) SYMBOL DESCRIPTION MIN TYP MAX UNITS A[N:0] t1a Setup time to RD, WR, DS active (Note 1) 10 ns ALE t1b Setup time to RD, WR, DS active (Notes 1, 2) 10 ns A[N:0] t2 Setup time to ALE inactive (Notes 1, 2) 2 ns A[N:0] t3 Hold time from ALE inactive (Notes 1, 2) 2 ns ALE t4 Pulse width (Notes 1, 2) 5 ns A[N:0], ALE t5 Hold time from RD, WR, DS inactive (Note 1) 0 ns CS, R/W t6 Setup time to RD, WR active (Note 1) 0 ns D[15:0] t8 Output delay time from RD, DS active (Note 1) RD, WR, DS t9a Pulse width if not using RDY handshake (Notes 1, 4) 35 ns RD, WR, DS t9b Delay from RDY (Note 1) 15 ns D[15:0] t10 Output deassert delay time from RD, DS inactive (Notes 1, 3) 2 CS, R/W t12 Hold time from RD, WR, DS inactive (Note 1) 0 ns D[15:0] t13 Input setup time to WR, DS inactive (Note 1) 10 ns D[15:0] t14 Input hold time from WR, DS inactive (Note 1) 5 ns RDY t15 Delay time from RD, WR, DS active (Note 1) 5 ns RDY t16 Delay time from RD, WR, DS inactive (Note 1) 0 ns RDY t17 Enable delay time from CS active (Note 1) 12 ns RDY t18 Disable delay time from CS inactive (Note 1) 10 ns RDY t19 Ending high pulse width (Note 1) 1 ns R/W t20 Setup time to DS active (Note 1) 2 ns R/W t21 Hold time to DS inactive (Note 1) 2 ns 30 10 ns ns Note 1: The input/output timing reference level for all signals is VDD/2. Transition time (80/20%) on RD, WR and CS inputs is 5ns max. Note 2: Multiplexed mode timing only. Note 3: D[15:0] output valid until not driven. Note 4: Timing required if not using RDY handshake. 390 DS3181/DS3182/DS3183/DS3184 Figure 18-7. Micro Interface Nonmultiplexed Read/Write Cycle t1a t5 A[10:0] t6 t12 CS* t8 t10 D[15:0] t13 t14 D[15:0] R/W* RD* WR* DS* t20 t21 t9a t17 t18 t9b RDY* t16 t15 391 t19 DS3181/DS3182/DS3183/DS3184 Figure 18-8. Micro Interface Multiplexed Read Cycle t1a A[10:0] t2 ALE t3 t5 t4 t1b t12 t6 CS* t8 t10 D[15:0] t13 t14 D[15:0] R/W* RD* WR* DS* t20 t21 t9a t17 t18 t9b RDY* t16 t15 392 t19 DS3181/DS3182/DS3183/DS3184 18.7 CLAD Jitter Characteristics PARAMETER MIN TYP MAX UNITS Intrinsic Jitter (UIP-P) 0.025 UIP-P Intrinsic Jitter (UIRMS) 0.0045 UIRMS Peak Jitter Transfer 1.75 dB 18.8 LIU Interface AC Characteristics 18.8.1 Waveform Templates Table 18-8. DS3 Waveform Template TIME (IN UNIT INTERVALS) NORMALIZED AMPLITUDE EQUATION UPPER CURVE -0.85 T -0.68 -0.68 T +0.36 0.36 T 1.4 -0.85 T -0.36 -0.36 T +0.36 0.36 T 1.4 0.03 0.5 {1 + sin[( / 2)(1 + T / 0.34)]} + 0.03 0.08 + 0.407e-1.84(T - 0.36) LOWER CURVE -0.03 0.5 {1 + sin[( / 2)(1 + T / 0.18)]} - 0.03 -0.03 Governing Specifications: ANSI T1.102 and Bellcore GR-499. Table 18-9. DS3 Waveform Test Parameters and Limits PARAMETER Rate Line Code Transmission Medium Test Measurement Point Test Termination Pulse Amplitude Pulse Shape Unframed All-Ones Power Level at 22.368MHz Unframed All-Ones Power Level at 44.736MHz Pulse Imbalance of Isolated Pulses SPECIFICATION 44.736Mbps (20ppm) B3ZS Coaxial cable (AT&T 734A or equivalent) At the end of 0 to 450ft of coaxial cable 75 (1%) resistive Between 0.36V and 0.85V An isolated pulse (preceded by two zeros and followed by one or more zeros) falls within the curves listed in Figure 18-9. Between -1.8dBm and +5.7dBm At least 20dB less than the power measured at 22.368MHz Ratio of positive and negative pulses must be between 0.90 and 1.10. 393 DS3181/DS3182/DS3183/DS3184 Table 18-10. STS-1 Waveform Template TIME (IN UNIT INTERVALS) -0.85 T -0.68 -0.68 T +0.26 0.26 T 1.4 -0.85 T -0.36 -0.36 T +0.36 0.36 T 1.4 NORMALIZED AMPLITUDE EQUATIONS UPPER CURVE 0.03 0.5 {1 + sin[( / 2)(1 + T / 0.34)]} + 0.03 0.1 + 0.61e-2.4(T - 0.26) LOWER CURVE -0.03 0.5 {1 + sin[( / 2)(1 + T / 0.18)]} - 0.03 -0.03 Governing Specifications: Bellcore GR-253 and Bellcore GR-499 and ANSI T1.102. Table 18-11. STS-1 Waveform Test Parameters and Limits PARAMETER Rate Line Code Transmission Medium Test Measurement Point Test Termination Pulse Amplitude Pulse Shape Unframed All-Ones Power Level at 25.92MHz Unframed All-Ones Power Level at 51.84MHz SPECIFICATION 51.840Mbps (20ppm) B3ZS Coaxial cable (AT&T 734A or equivalent) At the end of 0 to 450ft of coaxial cable 75 (1%) resistive 0.800V nominal (not covered in specs) An isolated pulse (preceded by two zeros and followed by one or more zeros) falls within the curved listed in Table 18-10. Between -1.8dBm and +5.7dBm At least 20dB less than the power measured at 25.92MHz. 394 DS3181/DS3182/DS3183/DS3184 Figure 18-9. E3 Waveform Template 1.2 1.1 17 1.0 0.9 8.65 0.8 0.7 G.703 E3 TEMPLATE OUTPUT LEVEL (V) 0.6 0.5 12.1 0.4 0.3 0.2 0.1 24.5 0 29.1 -0.1 -0.2 TIME (ns) Table 18-12. E3 Waveform Test Parameters and Limits PARAMETER Rate Line Code Transmission Medium Test Measurement Point Test Termination Pulse Amplitude Pulse Shape Ratio of the Amplitudes of Positive and Negative Pulses at the Center of the Pulse Interval Ratio of the Widths of Positive and Negative Pulses at the Nominal Half Amplitude SPECIFICATION 34.368Mbps (20ppm) HDB3 Coaxial cable (AT&T 734A or equivalent) At the transmitter 75 (1%) resistive 1.0V (nominal) An isolated pulse (preceded by two zeros and followed by one or more zeros) falls within the template shown in Figure 18-9. 0.95 to 1.05 0.95 to 1.05 395 DS3181/DS3182/DS3183/DS3184 Figure 18-10. STS-1 Pulse Mask Template 396 DS3181/DS3182/DS3183/DS3184 Figure 18-11. DS3 Pulse Mask Template 18.8.2 LIU Input/Output Characteristics Table 18-13. Receiver Input Characteristics--DS3 and STS-1 Modes (VDD = 3.3V 5%, TA = -40C to +85C.) PARAMETER Receive Sensitivity (Length of Cable) Signal-to-Noise Ratio, Interfering Signal Test (Notes 1, 2) Input Pulse Amplitude, RMON = 0 (Notes 2, 3) Input Pulse Amplitude, RMON = 1 (Notes 2, 3) Analog LOS Declare, RMON = 0 (Note 4) Analog LOS Clear, RMON = 0 (Note 4) Analog LOS Declare, RMON = 1 (Note 4) Analog LOS Clear, RMON = 1 (Note 4) Intrinsic Jitter Generation (Note 2) 397 MIN TYP 900 1200 10 -16 -24 -17 MAX ft 1000 200 -28 -38 -29 0.03 UNITS mVpk mVpk dB dB dB dB UIP-P DS3181/DS3182/DS3183/DS3184 Table 18-14. Receiver Input Characteristics--E3 Mode (VDD = 3.3V 5%, TA = -40C to +85C.) PARAMETER Receive Sensitivity (Length of Cable) Signal-to-Noise Ratio, Interfering Signal Test (Notes 1, 2) Input Pulse Amplitude, RMON = 0 (Notes 2, 3) Input Pulse Amplitude, RMON = 1 (Notes 2, 3) Analog LOS Declare, RMON = 0 (Note 4) Analog LOS Clear, RMON = 0 (Note 4) Analog LOS Declare, RMON = 1 (Note 4) Analog LOS Clear, RMON = 1 (Note 4) Intrinsic Jitter Generation (Note 2) 15 MIN TYP 900 1200 12 -16 -24 -17 MAX UNITS ft 1300 260 -28 -38 -29 0.03 mVpk mVpk dB dB dB dB UIP-P 23 Note 1: An interfering signal (2 - 1 PRBS for DS3/STS-1, 2 - 1 PRBS for E3, B3ZS/HDB3 encoded, compliant waveshape, nominal bit rate) is added to the wanted signal. The combined signal is passed through 0 to 900ft of coaxial cable and presented to the LIU. -9 This spec indicates the lowest signal-to-noise ratio that results in a bit error ratio <10 . Note 2: Not tested during production test. Note 3: Measured on the line side (i.e., the BNC connector side) of the 1:2 receive transformer (Figure 1-1). During measurement, incoming 15 23 data traffic is unframed 2 - 1 PRBS for DS3/STS-1 and unframed 2 - 1 PRBS for E3. Note 4: With respect to nominal 800mVpk signal for DS3/STS-1 and nominal 1000mVpk signal for E3. Table 18-15. Transmitter Output Characteristics--DS3 and STS-1 Modes (VDD = 3.3V 5%, TA = -40C to +85C.) PARAMETER DS3 Output Pulse Amplitude, TLBO = 0 (Note 5) DS3 Output Pulse Amplitude, TLBO = 1 (Note 5) CC52 Output Pulse Amplitude, TLBO = 0 (Note 5) CC52 Output Pulse Amplitude, TLBO = 1 (Note 5) Ratio of Positive and Negative Pulse-Peak Amplitudes DS3 Unframed All-Ones Power Level at 22.368MHz, 3kHz Bandwidth DS3 Unframed All-Ones Power Level at 44.736MHz vs. Power Level at 22.368MHz, 3kHz Bandwidth Intrinsic Jitter Generation (Note 5) MIN TYP MAX UNITS 700 520 700 520 0.9 800 700 800 700 900 800 1100 850 1.1 mVpk mVpk mVpk mVpk +5.7 dBm -20 dB 0.02 0.05 UIP-P MIN TYP MAX UNITS 900 1000 1100 mVpk -1.8 Table 18-16. Transmitter Output Characteristics--E3 Mode (VDD = 3.3V 5%, TA = -40C to +85C.) PARAMETER Output Pulse Amplitude (Note 5) Pulse Width 14.55 Ratio of Positive and Negative Pulse Amplitudes (at Centers of Pulses) Ratio of Positive and Negative Pulse Widths (at Nominal Half Amplitude) Intrinsic Jitter Generation (Note 6) ns 0.95 1.05 0.95 1.05 0.02 0.05 UIP-P Note 5: Measured on the line side (i.e., the BNC connector side) of the 2:1 transmit transformer (Figure 1-1). Note 6: Measured with jitter-free clock applied to TCLK and a bandpass jitter filter with 10Hz and 800kHz cutoff frequencies. Not tested during production test. 398 DS3181/DS3182/DS3183/DS3184 18.9 JTAG Interface AC Characteristics All AC timing characteristics are specified with a 50pF capacitive load on JTDO pin and 25pF capacitive load on all other digital output pins, VIH = 2.4V and VIL = 0.8. The voltage threshold for all timing measurements is VDD/2. The generic timing definitions shown Figure 18-1, Figure 18-2, Figure 18-3, Figure 18-5, and Figure 18-6 apply to this interface. Table 18-17. JTAG Interface Timing (VDD = 3.3V 5%, Tj = -40C to +125C.) SIGNAL NAME(S) SYMBOL DESCRIPTION MIN TYP MAX UNITS 10 MHz JTCLK f1 Clock frequency (1/t1) 0 JTCLK t2 Clock high or low period 20 JTCLK t3 Rise/fall times JTMS and JTDI t5 Hold time from JTCLK rising edge 10 ns JTMS and JTDI t6 Setup time to JTCLK rising edge 10 ns JTDO t7 Delay from JTCLK falling edge 0 30 ns JTDO t8 Delay out of high-Z from JTCLK falling edge 0 30 ns JTDO t9 Delay to high-Z from JTCLK falling edge 0 30 ns Any Digital Output t7 Delay from JTCLK falling edge (Note 1) 0 30 ns Any Digital Output t7 Delay from JTCLK rising edge (Note 2) 0 30 ns Any Digital Output t8 Delay out of high-Z from JTCLK falling edge (Note 1) 0 30 ns Any Digital Output t9 Delay into high-Z from JTCLK falling edge (Note 1) 0 30 ns Any Digital Output t8 Delay out of high-Z from JTCLK rising edge (Notes 2, 3) 0 30 ns Any Digital Output t9 Delay into high-Z from JTCLK rising edge (Notes 2, 3) 0 30 ns ns 5 Note 1: Change during Update-DR state. Note 2: Change during Update-IR state to or from EXTEST mode. Note 3: Change during Update-IR state to or from HIZ mode. 399 ns DS3181/DS3182/DS3183/DS3184 19 REVISION HISTORY REVISION DESCRIPTION 061604 New product release (DS3184). 121704 New product release (DS3181). 010705 New product release (DS3182). New product release for DS3183 on 01/21/05. Corrected register bit map (GL.RIORR). Clarified CP.TCR.TDSE and RCR.RDDE to state that DSS mode is only applicable for unframed modes and bit synchronous modes. Added clarification to Receive LIU stating that the master reference clock will use TCLKIn if no clock exists on CLKA, B, or C. Removed Note 3 from the DC Electrical Characteristics table since A2 fixes the problem with TEN and REN. 030205 Changed Input leakage for inputs with internal pullups from -300A to -350A. For DS3 and STS-1 and E3 Tables: Changed "Analog LOS Declare, RMON = 0" from -24dB max to -24dB typ, and added -28dB max. Changed "Analog LOS Clear, RMON = 0" from -17dB min to -17dB typ, and added -16dB min. Added TLCLK to reference clock sources for TPOS/TNEG in the Line Interface AC Characteristics table. Updated register bit map for PORT.INV. Corrected wording of use of unused bits located in the Overall Register Map section. Added IDD measurements for DS3181/DS3182/DS3183. 102406 Added lead-free package note to Ordering Information table (page 1). Updated Package Information (Section 15). Note: To obtain a revision history for the preliminary releases of this document, contact the factory at telecom.support@dalsemi.com. 400 Maxim/Dallas Semiconductor cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim/Dallas Semiconductor product. No circuit patent licenses are implied. Maxim/Dallas Semiconductor reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 (c) 2006 Maxim Integrated Products The Maxim logo is a registered trademark of Maxim Integrated Products, Inc. The Dallas logo is a registered trademark of Dallas SemiconductorCorporation.