Cyclone V Device Overview 2013.12.26 CV-51001 Subscribe Send Feedback The Cyclone(R) V devices are designed to simultaneously accommodate the shrinking power consumption, cost, and time-to-market requirements; and the increasing bandwidth requirements for high-volume and cost-sensitive applications. Enhanced with integrated transceivers and hard memory controllers, the Cyclone V devices are suitable for applications in the industrial, wireless and wireline, military, and automotive markets. Related Information Cyclone V Device Handbook: Known Issues Lists the planned updates to the Cyclone V Device Handbook chapters. Key Advantages of Cyclone V Devices Table 1: Key Advantages of the Cyclone V Device Family Advantage Supporting Feature Lower power consumption * Built on TSMC's 28 nm low-power (28LP) process technology and includes an abundance of hard intellectual property (IP) blocks * Up to 40% lower power consumption than the previous generation device Improved logic integration and differentiation capabilities * 8-input adaptive logic module (ALM) * Up to 13.59 megabits (Mb) of embedded memory * Variable-precision digital signal processing (DSP) blocks Increased bandwidth capacity * 3.125 gigabits per second (Gbps) and 6.144 Gbps transceivers * Hard memory controllers Hard processor system (HPS) with * Tight integration of a dual-core ARM Cortex-A9 MPCore (R) TM integrated ARM Cortex -A9 MPCore processor, hard IP, and an FPGA in a single Cyclone V systemprocessor on-a-chip (SoC) * Supports over 128 Gbps peak bandwidth with integrated data coherency between the processor and the FPGA fabric (c) 2013 Altera Corporation. All rights reserved. ALTERA, ARRIA, CYCLONE, HARDCOPY, MAX, MEGACORE, NIOS, QUARTUS and STRATIX words and logos are trademarks of Altera Corporation and registered in the U.S. Patent and Trademark Office and in other countries. All other words and logos identified as trademarks or service marks are the property of their respective holders as described at www.altera.com/common/legal.html. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera's standard warranty, but reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device specifications before relying on any published information and before placing orders for products or services. www.altera.com 101 Innovation Drive, San Jose, CA 95134 ISO 9001:2008 Registered 2 CV-51001 2013.12.26 Summary of Cyclone V Features Advantage Supporting Feature Lowest system cost * Requires only two core voltages to operate * Available in low-cost wirebond packaging * Includes innovative features such as Configuration via Protocol (CvP) and partial reconfiguration Summary of Cyclone V Features Table 2: Summary of Features for Cyclone V Devices Feature Technology Packaging Description * TSMC's 28-nm low-power (28LP) process technology * 1.1 V core voltage * Wirebond low-halogen packages * Multiple device densities with compatible package footprints for seamless migration between different device densities * RoHS-compliant and leaded(1)options High-performance FPGA fabric Enhanced 8-input ALM with four registers Internal memory blocks Embedded Hard IP blocks * M10K--10-kilobits (Kb) memory blocks with soft error correction code (ECC) * Memory logic array block (MLAB)--640-bit distributed LUTRAM where you can use up to 25% of the ALMs as MLAB memory Variable-precision * Native support for up to three signal processing DSP precision levels (three 9 x 9, two 18 x 18, or one 27 x 27 multiplier) in the same variable-precision DSP block * 64-bit accumulator and cascade * Embedded internal coefficient memory * Preadder/subtractor for improved efficiency Memory controller DDR3, DDR2, and LPDDR2 with 16 and 32 bit ECC support Embedded transceiver I/O Clock networks (1) PCI Express(R) (PCIe(R)) Gen2 and Gen1 (x1, x2, or x4) hard IP with multifunction support, endpoint, and root port * Up to 550 MHz global clock network * Global, quadrant, and peripheral clock networks * Clock networks that are not used can be powered down to reduce dynamic power Contact Altera for availability. Altera Corporation Cyclone V Device Overview Send Feedback CV-51001 2013.12.26 Summary of Cyclone V Features Feature Phase-locked loops (PLLs) 3 Description * Precision clock synthesis, clock delay compensation, and zero delay buffering (ZDB) * Integer mode and fractional mode FPGA General-purpose I/Os * 875 megabits per second (Mbps) LVDS receiver and 840 Mbps LVDS (GPIOs) transmitter * 400 MHz/800 Mbps external memory interface * On-chip termination (OCT) * 3.3 V support with up to 16 mA drive strength Low-power high-speed serial * 614 Mbps to 6.144 Gbps integrated transceiver speed interface * Transmit pre-emphasis and receiver equalization * Dynamic partial reconfiguration of individual channels HPS (Cyclone V SE, SX, and ST devices only) Configuration Cyclone V Device Overview Send Feedback * Single or dual-core ARM Cortex-A9 MPCore processor-up to 925 MHz maximum frequency with support for symmetric and asymmetric multiprocessing * Interface peripherals--10/100/1000 Ethernet media access control (EMAC), USB 2.0 On-The-GO (OTG) controller, quad serial peripheral interface (QSPI) flash controller, NAND flash controller, Secure Digital/MultiMediaCard (SD/MMC) controller, UART, controller area network (CAN), serial peripheral interface (SPI), I2C interface, and up to 85 HPS GPIO interfaces * System peripherals--general-purpose timers, watchdog timers, direct memory access (DMA) controller, FPGA configuration manager, and clock and reset managers * On-chip RAM and boot ROM * HPS-FPGA bridges--include the FPGA-to-HPS, HPS-to-FPGA, and lightweight HPS-to-FPGA bridges that allow the FPGA fabric to issue transactions to slaves in the HPS, and vice versa * FPGA-to-HPS SDRAM controller subsystem--provides a configurable interface to the multiport front end (MPFE) of the HPS SDRAM controller * ARM CoreSightTM JTAG debug access port, trace port, and on-chip trace storage * Tamper protection--comprehensive design protection to protect your valuable IP investments * Enhanced advanced encryption standard (AES) design security features * CvP * Partial and dynamic reconfiguration of the FPGA * Active serial (AS) x1 and x4, passive serial (PS), JTAG, and fast passive parallel (FPP) x8 and x16 configuration options Altera Corporation 4 CV-51001 2013.12.26 Cyclone V Device Variants and Packages Cyclone V Device Variants and Packages Table 3: Device Variants for the Cyclone V Device Family Variant Description Cyclone V E Optimized for the lowest system cost and power requirement for a wide spectrum of general logic and DSP applications Cyclone V GX Optimized for the lowest cost and power requirement for 614 Mbps to 3.125 Gbps transceiver applications Cyclone V GT The FPGA industry's lowest cost and lowest power requirement for 6.144 Gbps transceiver applications Cyclone V SE SoC with integrated ARM-based HPS Cyclone V SX SoC with integrated ARM-based HPS and 3.125 Gbps transceivers Cyclone V ST SoC with integrated ARM-based HPS and 5 Gbps transceivers Cyclone V E This section provides the available options, maximum resource counts, and package plan for the Cyclone V E devices. The information in this section is correct at the time of publication. For the latest information and to get more details, refer to the Altera Product Selector. Related Information Altera Product Selector Provides the latest information about Altera products. Altera Corporation Cyclone V Device Overview Send Feedback CV-51001 2013.12.26 5 Available Options Available Options Figure 1: Sample Ordering Code and Available Options for Cyclone V E Devices Package Type F : FineLine BGA (FBGA) U : Ultra FineLine BGA (UBGA) M : Micro FineLine BGA (MBGA) Operating Temperature C : Commercial (TJ = 0 C to 85 C) I : Industrial (TJ = -40 C to 100 C) A : Automotive (TJ = -40 C to 125 C) Embedded Hard IPs B : No hard PCIe or hard memory controller F : No hard PCIe and maximum 2 hard memory controllers E 5C Family Signature 5C : Cyclone V F Family Variant E : Enhanced logic/memory Member Code A2 A4 A5 A7 A9 : : : : : 25K logic elements 49K logic elements 77K logic elements 149.5K logic elements 301K logic elements A9 F 31 C N 7 Optional Suffix Indicates specific device options or shipment method N : Lead-free packaging Contact Altera for availability of leaded options ES : Engineering sample Package Code FBGA Package Type 17 : 256 pins 23 : 484 pins 27 : 672 pins 31 : 896 pins UBGA Package Type 15 : 324 pins 19 : 484 pins MBGA Package Type 13 : 383 pins 15 : 484 pins FPGA Fabric Speed Grade 6 (fastest) 7 8 Maximum Resources Table 4: Maximum Resource Counts for Cyclone V E Devices Member Code Resource A2 A4 A5 A7 A9 25 49 77 149.5 301 ALM 9,434 18,480 29,080 56,480 113,560 Register 37,736 73,920 116,320 225,920 454,240 M10K 1,760 3,080 4,460 6,860 12,200 MLAB 196 303 424 836 1,717 Variable-precision DSP Block 25 66 150 156 342 18 x 18 Multiplier 50 132 300 312 684 PLL 4 4 6 7 8 224 224 240 480 480 Transmitter 56 56 60 120 120 Receiver 56 56 60 120 120 1 1 2 2 2 Logic Elements (LE) (K) Memory (Kb) GPIO LVDS Hard Memory Controller Cyclone V Device Overview Send Feedback Altera Corporation 6 CV-51001 2013.12.26 Package Plan Related Information I/O Features in Cyclone V Devices Provides the number of LVDS channels in each device package. Package Plan Table 5: Package Plan for Cyclone V E Devices M383 M484 U324 F256 U484 F484 F672 F896 (13 mm) (15 mm) (15 mm) (17 mm) (19 mm) (23 mm) (27 mm) (31 mm) GPIO GPIO GPIO GPIO GPIO GPIO GPIO GPIO A2 223 -- 176 128 224 224 -- -- A4 223 -- 176 128 224 224 -- -- A5 175 -- -- -- 224 240 -- -- A7 -- 240 -- -- 240 240 336 480 A9 -- -- -- -- 240 224 336 480 Member Code Cyclone V GX This section provides the available options, maximum resource counts, and package plan for the Cyclone V GX devices. The information in this section is correct at the time of publication. For the latest information and to get more details, refer to the Altera Product Selector. Related Information Altera Product Selector Provides the latest information about Altera products. Available Options The following figure shows sample ordering code and lists the options available for Cyclone V GX devices. Altera Corporation Cyclone V Device Overview Send Feedback CV-51001 2013.12.26 Maximum Resources 7 Figure 2: Sample Ordering Code and Available Options for Cyclone V GX Devices Embedded Hard IPs B : No hard PCIe or hard memory controller F : Maximum 2 hard PCIe and 2 hard memory controllers Family Signature 5C : Cyclone V 5C GX F C9 E 6 Family Variant GX : 3-Gbps transceivers Member Code C3 : 31.5K logic elements C4 : 50K logic elements C5 : 77K logic elements C7 : 149.5K logic elements C9 : 301K logic elements Package Type F : FineLine BGA (FBGA) U : Ultra FineLine BGA (UBGA) M : Micro FineLine BGA (MBGA) Transceiver Count B : 3 F : 4 A : 5 C : 6 D : 9 E : 12 Transceiver Speed Grade 6 : 3.125 Gbps 7 : 2.5 Gbps Operating Temperature C : Commercial (TJ = 0 C to 85 C) I : Industrial (TJ = -40 C to 100 C) A : Automotive (TJ = -40 C to 125 C) F 35 C Package Code FBGA Package Type 23 : 484 pins 27 : 672 pins 31 : 896 pins 35 : 1,152 pins UBGA Package Type 15 : 324 pins 19 : 484 pins MBGA Package Type 11 : 301 pins 13 : 383 pins 15 : 484 pins 7 N Optional Suffix Indicates specific device options or shipment method N : Lead-free packaging Contact Altera for availability of leaded options ES : Engineering sample FPGA Fabric Speed Grade 6 (fastest) 7 8 Maximum Resources Table 6: Maximum Resource Counts for Cyclone V GX Devices Member Code Resource C3 C4 C5 C7 C9 31.5 50 77 149.5 301 ALM 11,900 18,868 29,080 56,480 113,560 Register 47,600 75,472 116,320 225,920 454,240 M10K 1,190 2,500 4,460 6,860 12,200 MLAB 159 295 424 836 1,717 Variable-precision DSP Block 51 70 150 156 342 18 x 18 Multiplier 102 140 300 312 684 4 6 6 7 8 3 6 6 9 12 208 336 336 480 560 Transmitter 52 84 84 120 140 Receiver 52 84 84 120 140 Logic Elements (LE) (K) Memory (Kb) PLL 3 Gbps Transceiver (2) GPIO LVDS (2) The number of GPIOs does not include transceiver I/Os. In the Quartus II software, the number of user I/Os includes transceiver I/Os. Cyclone V Device Overview Send Feedback Altera Corporation 8 CV-51001 2013.12.26 Package Plan Member Code Resource C3 C4 C5 C7 C9 PCIe Hard IP Block 1 2 2 2 2 Hard Memory Controller 1 2 2 2 2 Related Information I/O Features in Cyclone V Devices Provides the number of LVDS channels in each device package. Package Plan Table 7: Package Plan for Cyclone V GX Devices Member Code M301 M383 M484 U324 U484 F484 F672 F896 F1152 (11 mm) (13 mm) (15 mm) (15 mm) (19 mm) (23 mm) (27 mm) (31 mm) (35 mm) GPIO XCVR GPIO XCVR GPIO XCVR GPIO XCVR GPIO XCVR GPIO XCVR GPIO XCVR GPIO XCVR GPIO XCVR C3 -- -- -- -- -- -- 144 3 208 3 208 3 -- -- -- -- -- -- C4 129 4 175 6 -- -- -- -- 224 6 240 6 336 6 -- -- -- -- C5 129 4 175 6 -- -- -- -- 224 6 240 6 336 6 -- -- -- -- C7 -- -- -- -- 240 3 -- -- 240 6 240 6 336 9 480 9 -- -- C9 -- -- -- -- -- -- -- -- 240 5 224 6 336 9 480 12 560 12 Cyclone V GT This section provides the available options, maximum resource counts, and package plan for the Cyclone V GT devices. The information in this section is correct at the time of publication. For the latest information and to get more details, refer to the Altera Product Selector. Related Information Altera Product Selector Provides the latest information about Altera products. Available Options The following figure shows sample ordering code and lists the options available for Cyclone V GT devices. Altera Corporation Cyclone V Device Overview Send Feedback CV-51001 2013.12.26 Maximum Resources 9 Figure 3: Sample Ordering Code and Available Options for Cyclone V GT Devices Transceiver Count B : 3 F : 4 A : 5 C : 6 D : 9 E : 12 Embedded Hard IPs F : Maximum 2 hard PCIe and 2 hard memory controllers Family Signature 5C : Cyclone V 5C GT F D9 E Operating Temperature C : Commercial (TJ = 0 C to 85 C) I : Industrial (TJ = -40 C to 100 C) A : Automotive (TJ = -40 C to 125 C) 5 Family Variant GT : 6-Gbps transceivers Member Code D5 : 77K logic elements D7 : 149.5K logic elements D9 : 301K logic elements Package Type F : FineLine BGA (FBGA) U : Ultra FineLine BGA (UBGA) M : Micro FineLine BGA (MBGA) Transceiver Speed Grade 5 : 6.144 Gbps F 35 C N 7 Optional Suffix Indicates specific device options or shipment method N : Lead-free packaging Contact Altera for availability of leaded options ES : Engineering sample Package Code FBGA Package Type 23 : 484 pins 27 : 672 pins 31 : 896 pins 35 : 1,152 pins UBGA Package Type 19 : 484 pins MBGA Package Type 11 : 301 pins 13 : 383 pins 15 : 484 pins FPGA Fabric Speed Grade 6 (fastest) 7 8 Maximum Resources Table 8: Maximum Resource Counts for Cyclone V GT Devices Member Code Resource D5 D7 D9 77 149.5 301 ALM 29,080 56,480 113,560 Register 116,320 225,920 454,240 M10K 4,460 6,860 12,200 MLAB 424 836 1,717 Variable-precision DSP Block 150 156 342 18 x 18 Multiplier 300 312 684 6 7 8 6 9 12 336 480 560 Transmitter 84 120 140 Receiver 84 120 140 2 2 2 Logic Elements (LE) (K) Memory (Kb) PLL 6 Gbps Transceiver (3) GPIO LVDS PCIe Hard IP Block (3) The number of GPIOs does not include transceiver I/Os. In the Quartus II software, the number of user I/Os includes transceiver I/Os. Cyclone V Device Overview Send Feedback Altera Corporation 10 CV-51001 2013.12.26 Package Plan Member Code Resource D5 D7 D9 2 2 2 Hard Memory Controller Related Information I/O Features in Cyclone V Devices Provides the number of LVDS channels in each device package. Package Plan Table 9: Package Plan for Cyclone V GT Devices Member Code M301 M383 M484 U484 F484 F672 F896 F1152 (11 mm) (13 mm) (15 mm) (19 mm) (23 mm) (27 mm) (31 mm) (35 mm) GPIO XCVR GPIO XCVR GPIO XCVR GPIO XCVR GPIO XCVR GPIO XCVR GPIO XCVR GPIO XCVR D5 129 4 175 6 -- -- 224 6 240 6 336 6 -- -- -- -- D7 -- -- -- -- 240 3 240 6 240 6 336 9(4) 480 9(4) -- -- D9 -- -- -- -- -- -- 240 5 224 6 336 9(4) 480 12(5) 560 12(5) Cyclone V SE This section provides the available options, maximum resource counts, and package plan for the Cyclone V SE devices. The information in this section is correct at the time of publication. For the latest information and to get more details, refer to the Altera Product Selector. Related Information Altera Product Selector Provides the latest information about Altera products. Available Options The following figure shows sample ordering code and lists the options available for Cyclone V SE devices. (4) (5) If you require CPRI (at 6.144 Gbps) and PCIe Gen2 transmit jitter compliance, Altera recommends that you use only up to three full-duplex transceiver channels for CPRI, and up to six full-duplex channels for PCIe Gen2. The CMU channels are not considered full-duplex channels. If you require CPRI (at 6.144 Gbps) and PCIe Gen2 transmit jitter compliance, Altera recommends that you use only up to three full-duplex transceiver channels for CPRI, and up to eight full-duplex channels for PCIe Gen2. The CMU channels are not considered full-duplex channels. Altera Corporation Cyclone V Device Overview Send Feedback CV-51001 2013.12.26 Maximum Resources 11 Figure 4: Sample Ordering Code and Available Options for Cyclone V SE Devices Package Type F : FineLine BGA (FBGA) U : Ultra FineLine BGA (UBGA) Operating Temperature C : Commercial (TJ = 0 C to 85 C) I : Industrial (TJ = -40 C to 100 C) A : Automotive (TJ = -40 C to 125 C) Embedded Hard IPs B : No hard PCIe or hard memory controller M : No hard PCIe and 1 hard memory controller Family Signature 5C : Cyclone V 5C Processor Cores Omit for dual-core S : Single-core SE M Family Variant SE : SoC with enhanced logic/memory Member Code A2 : 25K logic elements A4 : 40K logic elements A5 : 85K logic elements A6 : 110K logic elements A6 F 31 C Package Code FBGA Package Type 31 : 896 pins UBGA Package Type 19 : 484 pins 23 : 672 pins 6 S N Optional Suffix Indicates specific device options or shipment method N : Lead-free packaging Contact Altera for availability FPGA Fabric of leaded options Speed Grade ES : Engineering sample 6 (fastest) 7 8 Maximum Resources Table 10: Maximum Resource Counts for Cyclone V SE Devices Member Code Resource A2 A4 A5 A6 25 40 85 110 ALM 9,434 15,094 32,075 41,509 Register 37,736 60,376 128,300 166,036 M10K 1,400 2,700 3,970 5,570 MLAB 138 231 480 621 Variable-precision DSP Block 36 84 87 112 18 x 18 Multiplier 72 168 174 224 FPGA PLL 5 5 6 6 HPS PLL 3 3 3 3 FPGA GPIO 145 145 288 288 HPS I/O 181 181 181 181 Transmitter 32 32 72 72 Receiver 37 37 72 72 FPGA Hard Memory Controller 1 1 1 1 HPS Hard Memory Controller 1 1 1 1 Single- or dual-core Single- or dual-core Single- or dualcore Single- or dual-core Logic Elements (LE) (K) Memory (Kb) LVDS ARM Cortex-A9 MPCore Processor Cyclone V Device Overview Send Feedback Altera Corporation 12 CV-51001 2013.12.26 Package Plan Related Information I/O Features in Cyclone V Devices Provides the number of LVDS channels in each device package. Package Plan Table 11: Package Plan for Cyclone V SE Devices The HPS I/O counts are the number of I/Os in the HPS and does not correlate with the number of HPS-specific I/O pins in the FPGA. Each HPS-specific pin in the FPGA may be mapped to several HPS I/Os. Member Code U484 U672 F896 (19 mm) (23 mm) (31 mm) FPGA GPIO HPS I/O FPGA GPIO HPS I/O FPGA GPIO HPS I/O A2 66 151 145 181 -- -- A4 66 151 145 181 -- -- A5 66 151 145 181 288 181 A6 66 151 145 181 288 181 Cyclone V SX This section provides the available options, maximum resource counts, and package plan for the Cyclone V SX devices. The information in this section is correct at the time of publication. For the latest information and to get more details, refer to the Altera Product Selector. Related Information Altera Product Selector Provides the latest information about Altera products. Available Options The following figure shows sample ordering code and lists the options available for Cyclone V SX devices. Altera Corporation Cyclone V Device Overview Send Feedback CV-51001 2013.12.26 Maximum Resources 13 Figure 5: Sample Ordering Code and Available Options for Cyclone V SX Devices Package Type F : FineLine BGA (FBGA) U : Ultra FineLine BGA (UBGA) Embedded Hard IPs F : Maximum 2 hard PCIe controllers and 1 hard memory controller Family Signature 5C : Cyclone V 5C Operating Temperature C : Commercial (TJ = 0 C to 85 C) I : Industrial (TJ = -40 C to 100 C) A : Automotive (TJ = -40 C to 125 C) Transceiver Count C : 6 D : 9 SX F C6 D 6 F 31 C Family Variant SX : SoC with 3-Gbps transceivers Member Code C2 : C4 : C5 : C6 : 25K logic elements 40K logic elements 85K logic elements 110K logic elements Transceiver Speed Grade 6 : 3.125 Gbps Package Code FBGA Package Type 31 : 896 pins UBGA Package Type 23 : 672 pins 6 N Optional Suffix Indicates specific device options or shipment method N : Lead-free packaging Contact Altera for availability of leaded options ES : Engineering sample FPGA Fabric Speed Grade 6 (fastest) 7 8 Maximum Resources Table 12: Maximum Resource Counts for Cyclone V SX Devices Member Code Resource C2 C4 C5 C6 25 40 85 110 ALM 9,434 15,094 32,075 41,509 Register 37,736 60,376 128,300 166,036 M10K 1,400 2,700 3,970 5,570 MLAB 138 231 480 621 Variable-precision DSP Block 36 84 87 112 18 x 18 Multiplier 72 168 174 224 FPGA PLL 5 5 6 6 HPS PLL 3 3 3 3 6 6 9 9 FPGA GPIO 145 145 288 288 HPS I/O 181 181 181 181 Transmitter 32 32 72 72 Receiver 37 37 72 72 Logic Elements (LE) (K) Memory (Kb) 3 Gbps Transceiver (6) LVDS (6) The number of GPIOs does not include transceiver I/Os. In the Quartus II software, the number of user I/Os includes transceiver I/Os. Cyclone V Device Overview Send Feedback Altera Corporation 14 CV-51001 2013.12.26 Package Plan Member Code Resource C2 C4 C5 C6 (7) 2 (7) PCIe Hard IP Block 2 2 FPGA Hard Memory Controller 1 1 1 1 HPS Hard Memory Controller 1 1 1 1 Dual-core Dual-core Dual-core Dual-core ARM Cortex-A9 MPCore Processor 2 Related Information I/O Features in Cyclone V Devices Provides the number of LVDS channels in each device package. Package Plan Table 13: Package Plan for Cyclone V SX Devices The HPS I/O counts are the number of I/Os in the HPS and does not correlate with the number of HPS-specific I/O pins in the FPGA. Each HPS-specific pin in the FPGA may be mapped to several HPS I/Os. Member Code U672 F896 (23 mm) (31 mm) FPGA GPIO HPS I/O XCVR FPGA GPIO HPS I/O XCVR C2 145 181 6 -- -- -- C4 145 181 6 -- -- -- C5 145 181 6 288 181 9 C6 145 181 6 288 181 9 Cyclone V ST This section provides the available options, maximum resource counts, and package plan for the Cyclone V ST devices. The information in this section is correct at the time of publication. For the latest information and to get more details, refer to the Altera Product Selector. Related Information Altera Product Selector Provides the latest information about Altera products. Available Options The following figure shows sample ordering code and lists the options available for Cyclone V ST devices. (7) 1 PCIe Hard IP Block in U672 package. Altera Corporation Cyclone V Device Overview Send Feedback CV-51001 2013.12.26 Maximum Resources 15 Figure 6: Sample Ordering Code and Available Options for Cyclone V ST Devices Package Type F : FineLine BGA (FBGA) Embedded Hard IPs F : 2 hard PCIe controllers and 1 hard memory controller Family Signature 5C : Cyclone V 5C ST Operating Temperature C : Commercial (TJ = 0 C to 85 C) I : Industrial (TJ = -40 C to 100 C) A : Automotive (TJ = -40 C to 125 C) Transceiver Count D : 9 F D6 D Family Variant ST : SoC with 5-Gbps transceivers Member Code D5 : 85K logic elements D6 : 110K logic elements 5 F 31 C Package Code 31 : 896 pins Transceiver Speed Grade 5 : 5 Gbps 6 N Optional Suffix Indicates specific device options or shipment method FPGA Fabric N : Lead-free packaging Speed Grade Contact Altera for availability of leaded options 6 (fastest) ES : Engineering sample 7 8 Maximum Resources Table 14: Maximum Resource Counts for Cyclone V ST Devices Member Code Resource D5 D6 85 110 ALM 32,075 41,509 Register 128,300 166,036 M10K 3,970 5,570 MLAB 480 621 Variable-precision DSP Block 87 112 18 x 18 Multiplier 174 224 FPGA PLL 6 6 HPS PLL 3 3 9 9 FPGA GPIO 288 288 HPS I/O 181 181 Transmitter 72 72 Receiver 72 72 PCIe Hard IP Block 2 2 FPGA Hard Memory Controller 1 1 Logic Elements (LE) (K) Memory (Kb) 5 Gbps Transceiver (8) LVDS (8) The number of GPIOs does not include transceiver I/Os. In the Quartus II software, the number of user I/Os includes transceiver I/Os. Cyclone V Device Overview Send Feedback Altera Corporation 16 CV-51001 2013.12.26 Package Plan Member Code Resource D5 D6 1 1 Dual-core Dual-core HPS Hard Memory Controller ARM Cortex-A9 MPCore Processor Related Information I/O Features in Cyclone V Devices Provides the number of LVDS channels in each device package. Package Plan Table 15: Package Plan for Cyclone V ST Devices The HPS I/O counts are the number of I/Os in the HPS and does not correlate with the number of HPS-specific I/O pins in the FPGA. Each HPS-specific pin in the FPGA may be mapped to several HPS I/Os. F896 (31 mm) Member Code (9) FPGA GPIO HPS I/O XCVR D5 288 181 9(9) D6 288 181 9(9) If you require CPRI (at 4.9152 Gbps) and PCIe Gen2 transmit jitter compliance, Altera recommends that you use only up to seven full-duplex transceiver channels for CPRI, and up to six full-duplex channels for PCIe Gen2. The CMU channels are not considered full-duplex channels. Altera Corporation Cyclone V Device Overview Send Feedback CV-51001 2013.12.26 I/O Vertical Migration for Cyclone V Devices 17 I/O Vertical Migration for Cyclone V Devices Figure 7: Vertical Migration Capability Across Cyclone V Device Packages and Densities The arrows indicate the vertical migration paths. The devices included in each vertical migration path are shaded. You can also migrate your design across device densities in the same package option if the devices have the same dedicated pins, configuration pins, and power pins. Variant Member Code Package M301 M383 M484 F256 U324 U484 F484 U672 F672 F896 F1152 A2 A4 Cyclone V E A5 A7 A9 C3 C4 Cyclone V GX C5 C7 C9 D5 Cyclone V GT D7 D9 A2 Cyclone V SE A4 A5 A6 C2 Cyclone V SX C4 C5 C6 Cyclone V ST D5 D6 You can achieve the vertical migration shaded in red if you use only up to 175 GPIOs. This migration path is not shown in the Quartus II software Pin Migration View. Note: To verify the pin migration compatibility, use the Pin Migration View window in the Quartus(R) II software Pin Planner. Adaptive Logic Module Cyclone V devices use a 28 nm ALM as the basic building block of the logic fabric. The ALM, as shown in following figure, uses an 8-input fracturable look-up table (LUT) with four dedicated registers to help improve timing closure in register-rich designs and achieve an even higher design packing capability than previous generations. Cyclone V Device Overview Send Feedback Altera Corporation 18 CV-51001 2013.12.26 Variable-Precision DSP Block Figure 8: ALM for Cyclone V Devices FPGA Device Reg 1 2 3 4 5 6 7 8 Full Adder Reg Adaptive LUT Reg Full Adder Reg You can configure up to 25% of the ALMs in the Cyclone V devices as distributed memory using MLABs. Related Information Embedded Memory Capacity in Cyclone V Devices on page 20 Lists the embedded memory capacity for each device. Variable-Precision DSP Block Cyclone V devices feature a variable-precision DSP block that supports these features: * * * * * * * * * Configurable to support signal processing precisions ranging from 9 x 9, 18 x 18 and 27 x 27 bits natively A 64-bit accumulator A hard preadder that is available in both 18- and 27-bit modes Cascaded output adders for efficient systolic finite impulse response (FIR) filters Internal coefficient register banks, 8 deep, for each multiplier in 18- or 27-bit mode Fully independent multiplier operation A second accumulator feedback register to accommodate complex multiply-accumulate functions Efficient support for single-precision floating point arithmetic The inferability of all modes by the Quartus II design software Table 16: Variable-Precision DSP Block Configurations for Cyclone V Devices Usage Example Multiplier Size (Bit) DSP Block Resource Low precision fixed point for video applications Three 9 x 9 1 Medium precision fixed point in FIR filters Two 18 x 18 1 Two 18 x 18 with accumulate 1 FIR filters and general DSP usage Altera Corporation Cyclone V Device Overview Send Feedback CV-51001 2013.12.26 19 Variable-Precision DSP Block Usage Example High precision fixed- or floating-point implementations Multiplier Size (Bit) DSP Block Resource One 27 x 27 with accumulate 1 You can configure each DSP block during compilation as independent three 9 x 9, two 18 x 18, or one 27 x 27 multipliers. With a dedicated 64 bit cascade bus, you can cascade multiple variable-precision DSP blocks to implement even higher precision DSP functions efficiently. Table 17: Number of Multipliers in Cyclone V Devices The table lists the variable-precision DSP resources by bit precision for each Cyclone V device. Independent Input and Output Variant Cyclone V E Cyclone V GX Cyclone V GT Cyclone V SE Cyclone V SX Cyclone V Device Overview Send Feedback Member Code Variableprecision DSP Block Multiplications Operator 9x9 18 x 18 27 x 27 Multiplier Multiplier Multiplier 18 x 18 18 x 18 Multiplier Adder Mode Multiplier Adder Summed with 36 bit Input A2 25 75 50 25 25 25 A4 66 198 132 66 66 66 A5 150 450 300 150 150 150 A7 156 468 312 156 156 156 A9 342 1,026 684 342 342 342 C3 51 153 102 51 51 51 C4 70 210 140 70 70 70 C5 150 450 300 150 150 150 C7 156 468 312 156 156 156 C9 342 1,026 684 342 342 342 D5 150 450 300 150 150 150 D7 156 468 312 156 156 156 D9 342 1,026 684 342 342 342 A2 36 108 72 36 36 36 A4 84 252 168 84 84 84 A5 87 261 174 87 87 87 A6 112 336 224 112 112 112 C2 36 108 72 36 36 36 C4 84 252 168 84 84 84 C5 87 261 174 87 87 87 C6 112 336 224 112 112 112 Altera Corporation 20 CV-51001 2013.12.26 Embedded Memory Blocks Independent Input and Output Variant Cyclone V ST Variableprecision Member Code Multiplications Operator 9x9 18 x 18 27 x 27 Multiplier Multiplier Multiplier DSP Block 18 x 18 18 x 18 Multiplier Adder Mode Multiplier Adder Summed with 36 bit Input D5 87 261 174 87 87 87 D6 112 336 224 112 112 112 Embedded Memory Blocks The embedded memory blocks in the devices are flexible and designed to provide an optimal amount of small- and large-sized memory arrays to fit your design requirements. Types of Embedded Memory The Cyclone V devices contain two types of memory blocks: * 10 Kb M10K blocks--blocks of dedicated memory resources. The M10K blocks are ideal for larger memory arrays while still providing a large number of independent ports. * 640 bit memory logic array blocks (MLABs)--enhanced memory blocks that are configured from dualpurpose logic array blocks (LABs). The MLABs are ideal for wide and shallow memory arrays. The MLABs are optimized for implementation of shift registers for digital signal processing (DSP) applications, wide shallow FIFO buffers, and filter delay lines. Each MLAB is made up of ten adaptive logic modules (ALMs). In the Cyclone V devices, you can configure these ALMs as ten 32 x 2 blocks, giving you one 32 x 20 simple dual-port SRAM block per MLAB. Embedded Memory Capacity in Cyclone V Devices Table 18: Embedded Memory Capacity and Distribution in Cyclone V Devices Variant Cyclone V E Cyclone V GX Altera Corporation M10K MLAB Member Code Block RAM Bit (Kb) Block RAM Bit (Kb) Total RAM Bit (Kb) A2 176 1,760 314 196 1,956 A4 308 3,080 485 303 3,383 A5 446 4,460 679 424 4,884 A7 686 6,860 1338 836 7,696 A9 1,220 12,200 2748 1,717 13,917 C3 119 1,190 255 159 1,349 C4 250 2,500 472 295 2,795 C5 446 4,460 679 424 4,884 C7 686 6,860 1338 836 7,696 C9 1,220 12,200 2748 1,717 13,917 Cyclone V Device Overview Send Feedback CV-51001 2013.12.26 Embedded Memory Configurations Variant M10K 21 MLAB Member Code Block RAM Bit (Kb) Block RAM Bit (Kb) Total RAM Bit (Kb) D5 446 4,460 679 424 4,884 D7 686 6,860 1338 836 7,696 D9 1,220 12,200 2748 1,717 13,917 A2 140 1,400 221 138 1,538 A4 270 2,700 370 231 2,460 A5 397 3,970 768 480 4,450 A6 557 5,570 994 621 5,761 C2 140 1,400 221 138 1,538 C4 270 2,700 370 231 2,460 C5 397 3,970 768 480 4,450 C6 557 5,570 994 621 5,761 D5 397 3,970 768 480 4,450 D6 557 5,570 994 621 5,761 Cyclone V GT Cyclone V SE Cyclone V SX Cyclone V ST Embedded Memory Configurations Table 19: Supported Embedded Memory Block Configurations for Cyclone V Devices This table lists the maximum configurations supported for the embedded memory blocks. The information is applicable only to the single-port RAM and ROM modes. Memory Block Depth (bits) Programmable Width MLAB 32 x16, x18, or x20 256 x40 or x32 512 x20 or x16 1K x10 or x8 2K x5 or x4 4K x2 8K x1 M10K Clock Networks and PLL Clock Sources Cyclone V devices have 16 global clock networks capable of up to 550 MHz operation. The clock network architecture is based on Altera's global, quadrant, and peripheral clock structure. This clock structure is supported by dedicated clock input pins and fractional PLLs. Note: To reduce power consumption, the Quartus II software identifies all unused sections of the clock network and powers them down. Cyclone V Device Overview Send Feedback Altera Corporation 22 CV-51001 2013.12.26 FPGA General Purpose I/O PLL Features The PLLs in the Cyclone V devices support the following features: * * * * * * * * * * * Frequency synthesis On-chip clock deskew Jitter attenuation Programmable output clock duty cycles PLL cascading Reference clock switchover Programmable bandwidth User-mode reconfiguration of PLLs Low power mode for each fractional PLL Dynamic phase shift Direct, source synchronous, zero delay buffer, external feedback, and LVDS compensation modes Fractional PLL In addition to integer PLLs, the Cyclone V devices use a fractional PLL architecture. The devices have up to eight PLLs, each with nine output counters. You can use the output counters to reduce PLL usage in two ways: * Reduce the number of oscillators that are required on your board by using fractional PLLs * Reduce the number of clock pins that are used in the device by synthesizing multiple clock frequencies from a single reference clock source If you use the fractional PLL mode, you can use the PLLs for precision fractional-N frequency synthesis--removing the need for off-chip reference clock sources in your design. The transceiver fractional PLLs that are not used by the transceiver I/Os can be used as general purpose fractional PLLs by the FPGA fabric. FPGA General Purpose I/O Cyclone V devices offer highly configurable GPIOs. The following list describes the features of the GPIOs: * Programmable bus hold and weak pull-up * LVDS output buffer with programmable differential output voltage (VOD ) and programmable preemphasis * On-chip parallel termination (RT OCT) for all I/O banks with OCT calibration to limit the termination impedance variation * On-chip dynamic termination that has the ability to swap between series and parallel termination, depending on whether there is read or write on a common bus for signal integrity * Easy timing closure support using the hard read FIFO in the input register path, and delay-locked loop (DLL) delay chain with fine and coarse architecture PCIe Gen1 and Gen2 Hard IP Cyclone V GX, GT, SX, and ST devices contain PCIe hard IP that is designed for performance and ease-of-use. The PCIe hard IP consists of the MAC, data link, and transaction layers. Altera Corporation Cyclone V Device Overview Send Feedback CV-51001 2013.12.26 External Memory Interface 23 The PCIe hard IP supports PCIe Gen2 and Gen1 end point and root port for up to x4 lane configuration. The PCIe Gen2 x4 support is PCIe-compatible. The PCIe endpoint support includes multifunction support for up to eight functions, as shown in the following figure. The integrated multifunction support reduces the FPGA logic requirements by up to 20,000 LEs for PCIe designs that require multiple peripherals. Figure 9: PCIe Multifunction for Cyclone V Devices External System FPGA Device USB I2C Bridge to PCIe ATA Local Local Peripheral 1 Peripheral 2 GbE CAN PCIe Link PCIe EP Root Complex PCIe RP Memory Controller SPI GPIO Host CPU The Cyclone V PCIe hard IP operates independently from the core logic. This independent operation allows the PCIe link to wake up and complete link training in less than 100 ms while the Cyclone V device completes loading the programming file for the rest of the device. In addition, the PCIe hard IP in the Cyclone V device provides improved end-to-end datapath protection using ECC. External Memory Interface This section provides an overview of the external memory interface in Cyclone V devices. Hard and Soft Memory Controllers Cyclone V devices support up to two hard memory controllers for DDR3, DDR2, and LPDDR2 SDRAM devices. Each controller supports 8 to 32 bit components of up to 4 gigabits (Gb) in density with two chip selects and optional ECC. For the Cyclone V SoC devices, an additional hard memory controller in the HPS supports DDR3, DDR2, and LPDDR2 SDRAM devices. All Cyclone V devices support soft memory controllers for DDR3, DDR2, and LPDDR2 SDRAM devices for maximum flexibility. External Memory Performance Table 20: External Memory Interface Performance in Cyclone V Devices The maximum and minimum operating frequencies depend on the memory interface standards and the supported delay-locked loop (DLL) frequency listed in the device datasheet. Interface DDR3 SDRAM Cyclone V Device Overview Send Feedback Maximum Frequency (MHz) Voltage (V) Hard Controller Soft Controller 1.5 400 303 303 1.35 400 303 303 Minimum Frequency (MHz) Altera Corporation 24 CV-51001 2013.12.26 HPS External Memory Performance Maximum Frequency (MHz) Voltage (V) Hard Controller Soft Controller DDR2 SDRAM 1.8 400 300 167 LPDDR2 SDRAM 1.2 333 300 167 Interface Minimum Frequency (MHz) Related Information External Memory Interface Spec Estimator For the latest information and to estimate the external memory system performance specification, use Altera's External Memory Interface Spec Estimator tool. HPS External Memory Performance Table 21: HPS External Memory Interface Performance The hard processor system (HPS) is available in Cyclone V SoC devices only. Interface Voltage (V) HPS Hard Controller (MHz) 1.5 400 1.35 400 DDR2 SDRAM 1.8 400 LPDDR2 SDRAM 1.2 333 DDR3 SDRAM Related Information External Memory Interface Spec Estimator For the latest information and to estimate the external memory system performance specification, use Altera's External Memory Interface Spec Estimator tool. Low-Power Serial Transceivers Cyclone V devices deliver the industry's lowest power 6.144 Gbps transceivers at an estimated 88 mW maximum power consumption per channel. Cyclone V transceivers are designed to be compliant with a wide range of protocols and data rates. Transceiver Channels The transceivers are positioned on the left outer edge of the device. The transceiver channels consist of the physical medium attachment (PMA), physical coding sublayer (PCS), and clock networks. Altera Corporation Cyclone V Device Overview Send Feedback CV-51001 2013.12.26 PMA Features 25 Figure 10: Device Chip Overview for Cyclone V GX and GT Devices The figure shows a Cyclone V FPGA with transceivers. Different Cyclone V devices may have a different floorplans than the one shown here. Hard PCS Hard PCS Hard PCS Clock Networks Transceiver PMA Transceiver PMA Transceiver PMA Fractional PLL Fractional PLLs I/O, LVDS, and Memory Interface Fractional PLLs Hard PCS Blocks PCIe Hard IP Blocks Transceiver PMA Blocks I/O, LVDS, and Memory Interface Hard Memory Controller Transceiver Individual Channels Core Logic Fabric and MLABs M10K Internal Memory Blocks Variable-Precision DSP Blocks Hard Memory Controller I/O, LVDS, and Memory Interface PMA Features To prevent core and I/O noise from coupling into the transceivers, the PMA block is isolated from the rest of the chip--ensuring optimal signal integrity. For the transceivers, you can use the channel PLL of an unused receiver PMA as an additional transmit PLL. Table 22: PMA Features of the Transceivers in Cyclone V Devices Features Capability Backplane support Driving capability up to 6.144 Gbps PLL-based clock recovery Superior jitter tolerance Programmable deserialization and Flexible deserialization width and configurable word alignment pattern word alignment Equalization and pre-emphasis * Up to 14.37 dB of pre-emphasis and up to 4.7 dB of equalization * No decision feedback equalizer (DFE) Ring oscillator transmit PLLs 614 Mbps to 6.144 Gbps Input reference clock range 20 MHz to 400 MHz Cyclone V Device Overview Send Feedback Altera Corporation 26 CV-51001 2013.12.26 PCS Features Features Capability Transceiver dynamic reconfigura- Allows the reconfiguration of a single channel without affecting the tion operation of other channels PCS Features The Cyclone V core logic connects to the PCS through an 8, 10, 16, 20, 32, or 40 bit interface, depending on the transceiver data rate and protocol. Cyclone V devices contain PCS hard IP to support PCIe Gen1 and Gen2, Gbps Ethernet (GbE), Serial RapidIO(R) (SRIO), and Common Public Radio Interface (CPRI). Most of the standard and proprietary protocols from 614 Mbps to 6.144 Gbps are supported. Table 23: Transceiver PCS Features for Cyclone V Devices PCS Support 3-Gbps and 6-Gbps Basic Data Rates(Gbps) 0.614 to 6.144 Transmitter Data Path Feature * * * * Phase compensation FIFO Byte serializer 8B/10B encoder Transmitter bit-slip PCIe Gen1 (x1, x2, x4) 2.5 and 5.0 PCIe Gen2 ( x1, x2, x4)(10) (11) * * * * * * * Word aligner Deskew FIFO Rate-match FIFO 8B/10B decoder Byte deserializer Byte ordering Receiver phase compensation FIFO * Dedicated PCIe PHY IP core * PIPE 2.0 interface to the core logic GbE 1.25 * Custom PHY IP core with * Custom PHY IP core with preset feature preset feature * GbE transmitter synchroniza- * GbE receiver synchronization state machine tion state machine XAUI (11) 3.125 * Dedicated XAUI PHY IP * Dedicated XAUI PHY IP core core * XAUI synchronization state * XAUI synchronization state machine for bonding four machine for realigning four channels channels HiGig (10) * Dedicated PCIe PHY IP core * PIPE 2.0 interface to the core logic Receiver Data Path Feature 3.75 PCIe Gen2 is supported only for Cyclone V GT devices. The PCIe Gen2 x4 support is PCIe-compatible. XAUI is supported through the soft PCS. Altera Corporation Cyclone V Device Overview Send Feedback CV-51001 2013.12.26 SoC with HPS PCS Support Data Rates(Gbps) SRIO 1.3 and 2.1 1.25 to 3.125 SDI, SD/HD, and 3GSDI 0.27(12), 1.485, and 2.97 JESD204A Serial ATA Gen1 and Gen2 CPRI 4.1(14) OBSAI RP3 V-by-One HS DisplayPort 1.2(15) (13) 0.3125 to 3.125 1.5 and 3.0 Transmitter Data Path Feature 27 Receiver Data Path Feature * Custom PHY IP core with * Custom PHY IP core with preset feature preset feature * SRIO version 2.1-compliant x2 * SRIO version 2.1-compliant and x4 channel bonding x2 and x4 deskew state machine Custom PHY IP core with preset Custom PHY IP core with feature preset feature * Custom PHY IP core with preset feature * Electrical idle * Custom PHY IP core with preset feature * Signal detect * Wider spread of asynchronous SSC 0.6144 to 6.144 * Dedicated deterministic latency * Dedicated deterministic PHY IP core latency PHY IP core 0.768 to * Transmitter (TX) manual * Receiver (RX) deterministic 3.072 bit-slip mode latency state machine Up to 3.75 1.62 and 2.7 Custom PHY IP core * Custom PHY IP core * Wider spread of asynchronous SSC SoC with HPS Each SoC combines an FPGA fabric and an HPS in a single device. This combination delivers the flexibility of programmable logic with the power and cost savings of hard IP in these ways: * Reduces board space, system power, and bill of materials cost by eliminating a discrete embedded processor * Allows you to differentiate the end product in both hardware and software, and to support virtually any interface standard * Extends the product life and revenue through in-field hardware and software updates (12) (13) (14) (15) The 0.27-Gbps data rate is supported using oversampling user logic that you must implement in the FPGA fabric. The 0.3125-Gbps data rate is supported using oversampling user logic that you must implement in the FPGA fabric. High-voltage output mode (1000-BASE-CX) is not supported. Pending characterization. Cyclone V Device Overview Send Feedback Altera Corporation 28 CV-51001 2013.12.26 HPS Features HPS Features The HPS consists of a dual-core ARM Cortex-A9 MPCore processor, a rich set of peripherals, and a shared multiport SDRAM memory controller, as shown in the following figure. Figure 11: HPS with Dual-Core ARM Cortex-A9 MPCore Processor Configuration Lightweight Controller FPGA-to-HPS HPS-to-FPGA HPS-to-FPGA FPGA Fabric FPGA Manager HPS Debug Access Port MPU Subsystem ARM Cortex-A9 MPCore ETR (Trace) SD/MMC Controller Ethernet MAC (2x) USB OTG (2x) FPGA-to-HPS SDRAM Level 3 Interconnect CPU0 CPU1 ARM Cortex-A9 with NEON/FPU, 32 KB Instruction Cache, 32 KB Data Cache, and Memory Management Unit ARM Cortex-A9 with NEON/FPU, 32 KB Instruction Cache, 32 KB Data Cache, and Memory Management Unit ACP NAND Flash Controller DMA Controller Multiport DDR SDRAM Controller with Optional ECC SCU Level 2 Cache (512 KB) STM 64 KB Boot ROM 64 KB On-Chip RAM Peripherals (UART, Timer, I2C, Watchdog Timer, GPIO, SPI, Clock Manager, Reset Manager, Scan Manager, System Manager, and Quad SPI Flash Controller) System Peripherals and Debug Access Port Each Ethernet MAC, USB OTG, NAND flash controller, and SD/MMC controller module has an integrated DMA controller. For modules without an integrated DMA controller, an additional DMA controller module provides up to eight channels of high-bandwidth data transfers. Peripherals that communicate off-chip are multiplexed with other peripherals at the HPS pin level. This allows you to choose which peripherals to interface with other devices on your PCB. The debug access port provides interfaces to industry standard JTAG debug probes and supports ARM CoreSight debug and core traces to facilitate software development. Altera Corporation Cyclone V Device Overview Send Feedback CV-51001 2013.12.26 HPS-FPGA AXI Bridges 29 HPS-FPGA AXI Bridges The HPS-FPGA bridges, which support the Advanced Microcontroller Bus Architecture (AMBA(R)) Advanced eXtensible Interface (AXITM) specifications, consist of the following bridges: * FPGA-to-HPS AXI bridge--a high-performance bus supporting 32, 64, and 128 bit data widths that allows the FPGA fabric to issue transactions to slaves in the HPS. * HPS-to-FPGA AXI bridge--a high-performance bus supporting 32, 64, and 128 bit data widths that allows the HPS to issue transactions to slaves in the FPGA fabric. * Lightweight HPS-to-FPGA AXI bridge--a lower latency 32 bit width bus that allows the HPS to issue transactions to slaves in the FPGA fabric. This bridge is primarily used for control and status register (CSR) accesses to peripherals in the FPGA fabric. The HPS-FPGA AXI bridges allow masters in the FPGA fabric to communicate with slaves in the HPS logic, and vice versa. For example, the HPS-to-FPGA AXI bridge allows you to share memories instantiated in the FPGA fabric with one or both microprocessors in the HPS, while the FPGA-to-HPS AXI bridge allows logic in the FPGA fabric to access the memory and peripherals in the HPS. Each HPS-FPGA bridge also provides asynchronous clock crossing for data transferred between the FPGA fabric and the HPS. HPS SDRAM Controller Subsystem The HPS SDRAM controller subsystem contains a multiport SDRAM controller and DDR PHY that are shared between the FPGA fabric (through the FPGA-to-HPS SDRAM interface), the level 2 (L2) cache, and the level 3 (L3) system interconnect. The FPGA-to-HPS SDRAM interface supports AMBA AXI and Avalon(R) Memory-Mapped (Avalon-MM) interface standards, and provides up to six individual ports for access by masters implemented in the FPGA fabric. To maximize memory performance, the SDRAM controller subsystem supports command and data reordering, deficit round-robin arbitration with aging, and high-priority bypass features. The SDRAM controller subsystem supports DDR2, DDR3, or LPDDR2 devices up to 4 Gb in density operating at up to 400 MHz (800 Mbps data rate). FPGA Configuration and Processor Booting The FPGA fabric and HPS in the SoC are powered independently. You can reduce the clock frequencies or gate the clocks to reduce dynamic power, or shut down the entire FPGA fabric to reduce total system power. You can configure the FPGA fabric and boot the HPS independently, in any order, providing you with more design flexibility: * You can boot the HPS independently. After the HPS is running, the HPS can fully or partially reconfigure the FPGA fabric at any time under software control. The HPS can also configure other FPGAs on the board through the FPGA configuration controller. * You can power up both the HPS and the FPGA fabric together, configure the FPGA fabric first, and then boot the HPS from memory accessible to the FPGA fabric. Note: Although the FPGA fabric and HPS are on separate power domains, the HPS must remain powered up during operation while the FPGA fabric can be powered up or down as required. Cyclone V Device Overview Send Feedback Altera Corporation 30 CV-51001 2013.12.26 Hardware and Software Development Related Information Cyclone V Device Family Pin Connection Guidelines Provides detailed information about power supply pin connection guidelines and power regulator sharing. Hardware and Software Development For hardware development, you can configure the HPS and connect your soft logic in the FPGA fabric to the HPS interfaces using the Qsys system integration tool in the Quartus II software. For software development, the ARM-based SoC devices inherit the rich software development ecosystem available for the ARM Cortex-A9 MPCore processor. The software development process for Altera SoCs follows the same steps as those for other SoC devices from other manufacturers. Support for Linux, VxWorks(R), and other operating systems is available for the SoCs. For more information on the operating systems support availability, contact the Altera sales team. You can begin device-specific firmware and software development on the Altera SoC Virtual Target. The Virtual Target is a fast PC-based functional simulation of a target development system--a model of a complete development board that runs on a PC. The Virtual Target enables the development of device-specific production software that can run unmodified on actual hardware. Related Information Altera Worldwide Sales Support Dynamic and Partial Reconfiguration The Cyclone V devices support dynamic reconfiguration and partial reconfiguration(16). Dynamic Reconfiguration The dynamic reconfiguration feature allows you to dynamically change the transceiver data rates, PMA settings, or protocols of a channel, without affecting data transfer on adjacent channels. This feature is ideal for applications that require on-the-fly multiprotocol or multirate support. You can reconfigure the PMA and PCS blocks with dynamic reconfiguration. Partial Reconfiguration Note: Partial reconfiguration is an advanced feature of the device family. If you are interested in using partial reconfiguration, contact Altera for support. Partial reconfiguration allows you to reconfigure part of the device while other sections of the device remain operational. This capability is important in systems with critical uptime requirements because it allows you to make updates or adjust functionality without disrupting services. Apart from lowering cost and power consumption, partial reconfiguration increases the effective logic density of the device because placing device functions that do not operate simultaneously is not necessary. Instead, you can store these functions in external memory and load them whenever the functions are required. This (16) Partial reconfiguration is an advanced feature of the device family. If you are interested in using partial reconfiguration, contact Altera for support. Altera Corporation Cyclone V Device Overview Send Feedback CV-51001 2013.12.26 31 Enhanced Configuration and Configuration via Protocol capability reduces the size of the device because it allows multiple applications on a single device--saving the board space and reducing the power consumption. Altera simplifies the time-intensive task of partial reconfiguration by building this capability on top of the proven incremental compile and design flow in the Quartus II design software. With the Altera(R) solution, you do not need to know all the intricate device architecture details to perform a partial reconfiguration. Partial reconfiguration is supported through the FPP x16 configuration interface. You can seamlessly use partial reconfiguration in tandem with dynamic reconfiguration to enable simultaneous partial reconfiguration of both the device core and transceivers. Enhanced Configuration and Configuration via Protocol Cyclone V devices support 1.8 V, 2.5 V, 3.0 V, and 3.3 V programming voltages and several configuration modes. Table 24: Configuration Modes and Features Supported by Cyclone V Devices Mode Data Width Max Clock Max Data DecompresRate Rate sion (MHz) (Mbps) Design Security Partial Reconfigura(17) tion Remote System Update AS through the EPCS and EPCQ serial configuration device 1 bit, 4 bits 100 -- Yes Yes -- Yes PS through CPLD or external microcontroller 1 bit 125 125 Yes Yes -- -- 8 bits 125 -- Yes Yes -- 16 bits 125 -- Yes Yes Yes x1, x2, and x4 lanes -- -- Yes Yes Yes -- 1 bit 33 33 -- -- -- -- FPP CvP (PCIe) JTAG Parallel flash loader Instead of using an external flash or ROM, you can configure the Cyclone V devices through PCIe using CvP. The CvP mode offers the fastest configuration rate and flexibility with the easy-to-use PCIe hard IP block interface. The Cyclone V CvP implementation conforms to the PCIe 100 ms power-up-to-active time requirement. Related Information Configuration via Protocol (CvP) Implementation in Altera FPGAs User Guide Provides more information about CvP. (17) Partial reconfiguration is an advanced feature of the device family. If you are interested in using partial reconfiguration, contact Altera for support. Cyclone V Device Overview Send Feedback Altera Corporation 32 CV-51001 2013.12.26 Power Management Power Management Leveraging the FPGA architectural features, process technology advancements, and transceivers that are designed for power efficiency, the Cyclone V devices consume less power than previous generation Cyclone FPGAs: * Total device core power consumption--less by up to 40%. * Transceiver channel power consumption--less by up to 50%. Additionally, Cyclone V devices contain several hard IP blocks that reduce logic resources and deliver substantial power savings of up to 25% less power than equivalent soft implementations. Document Revision History Date December 2013 Altera Corporation Version 2013.12.26 Changes * Corrected single or dual-core ARM Cortex-A9 MPCore processor-up to 925 MHz from 800 MHz. * Removed "Preliminary" texts from Ordering Code figures, Maximum Resources, Package Plan and I/O Vertical Migration tables. * Removed the note "The number of GPIOs does not include transceiver I/Os. In the Quartus II software, the number of user I/Os includes transceiver I/Os." for GPIOs in the Maximum Resource Counts table for Cyclone V E and SE. * Added link to Altera Product Selector for each device variant. * Updated Embedded Hard IPs for Cyclone V GT devices to indicate Maximum 2 hard PCIe and 2 hard memory controllers. * Added leaded package options. * Removed the note "The number of PLLs includes general-purpose fractional PLLs and transceiver fractional PLLs." for all PLLs in the Maximum Resource Counts table. * Corrected max LVDS counts for transmitter and receiver for Cyclone V E A5 device from 84 to 60. * Corrected max LVDS counts for transmitter and receiver for Cyclone V E A9 device from 140 to 120. * Corrected variable-precision DSP block, 27 x 27 multiplier, 18 x 18 multiplier adder mode and 18 x 18 multiplier adder summed with 36 bit input for Cyclone V SE devices from 58 to 84. * Corrected 18 x 18 multiplier for Cyclone V SE devices from 116 to 168. * Corrected 9 x 9 multiplier for Cyclone V SE devices from 174 to 252. * Corrected LVDS transmitter for Cyclone V SE A2 and A4 as well as SX C2 and C4 devices from 31 to 32. * Corrected LVDS receiver for Cyclone V SE A2 and A4 as well as SX C2 and C4 devices from 35 to 37. * Corrected transceiver speed grade for Cyclone V ST devices ordering code from 4 to 5. Cyclone V Device Overview Send Feedback CV-51001 2013.12.26 Document Revision History Date Version 33 Changes * Updated the DDR3 SDRAM for the maximum frequency's soft controller and the minimum frequency from 300 to 303 for voltage 1.35V. * Added links to Altera's External Memory Spec Estimator tool to the topics listing the external memory interface performance. * Corrected XAUI is supported through the soft PCS in the PCS features for Cyclone V. * Added decompression support for the CvP configuration mode. May 2013 Cyclone V Device Overview Send Feedback 2013.05.06 * Added link to the known document issues in the Knowledge Base. * Moved all links to the Related Information section of respective topics for easy reference. * Corrected the title to the PCIe hard IP topic. Cyclone V devices support only PCIe Gen1 and Gen2. * Updated Supporting Feature in Table 1 of Increased bandwidth capacity to '6.144 Gbps'. * Updated Description in Table 2 of Low-power high-speed serial interface to '6.144 Gbps'. * Updated Description in Table 3 of Cyclone V GT to '6.144 Gbps'. * Updated the M386 package to M383 for Figure 1, Figure 2 and Figure 3. * Updated Figure 2 and Figure 3 for Transceiver Count by adding 'F : 4'. * Updated LVDS in the Maximum Resource Counts tables to include Transmitter and Receiver values. * Updated the package plan with M383 for the Cyclone V E device. * Removed the M301 and M383 packages from the Cyclone V GX C4 device. * Updated the GPIO count to '129' for the M301 package of the Cyclone V GX C5 device. * Updated 5 Gbps to '6.144 Gbps' forCyclone V GT device. * Updated HPS I/O for U484 (19 mm) in Table 11 with '151' for A2, A4, A5 and A6. * Updated Memory (Kb) for Maximum Resource Counts for Cyclone V SE A4 and A6, SX C4 and C6, ST D6 devices. * Updated FPGA PLL for Maximum Resource Counts for Cyclone V SE A2, SX C2, devices. * Removed '36 x 36' from the Variable-Precision DSP Block. * Updated Variable-precision DSP Blocks and 18 x 18 Multiplier for Maximum Resource Counts for Cyclone V SX C4 device. * Updated the HPS I/O counts for Cyclone V SE, SX, and ST devices. * Updated Figure 7 which shows the I/O vertical migration table. * Updated Table 17 for Cyclone V SX C4 device. * Updated Embedded Memory Capacity and Distribution table for Cyclone V SE A4 and A6, SX C4 and C6, ST D6 devices. * Removed 'Counter reconfiguration' from the PLL Features. Altera Corporation 34 CV-51001 2013.12.26 Document Revision History Date Version Changes * Updated Low-Power Serial Transceivers by replacing 5 Gbps with 6.144 Gbps. * Removed 'Distributed Memory' symbol. * Updated the Capability in Table 22 of Backplane support to '6.144 Gbps'. * Updated Capability in Table 22 of Ring oscillator transmit PLLs with 6.144 Gbps. * Updated the PCS Support in Table 23 from 5 Gbps to '6 Gbps'. * Updated the Data Rates (Gbps) in Table 23 of 3 Gbps and 6 Gbps Basic to '6.144 Gbps'. * Updated the Data Rates (Gbps) in Table 23 of CPRI 4.1 to '6.144 Gbps'. * Clarified that partial reconfiguration is an advanced feature. Contact Altera for support of the feature. December 2012 2012.12.28 * Updated the pin counts for the MBGA packages. * Updated the GPIO and transceiver counts for the MBGA packages. * Updated the GPIO counts for the U484 package of the Cyclone V E A9, GX C9, and GT D9 devices. * Updated the vertical migration table for vertical migration of the U484 packages. * Updated the MLAB supported programmable widths at 32 bits depth. November 2012 2012.11.19 * Added new MBGA packages and additional U484 packages for Cyclone V E, GX, and GT. * Added ordering code for five-transceiver devices for Cyclone V GT and ST. * Updated the vertical migration table to add MBGA packages. * Added performance information for HPS memory controller. * Removed DDR3U support. * Updated Cyclone V ST speed grade information. * Added information on maximum transceiver channel usage restrictions for PCI Gen2 and CPRI at 4.9152 Gbps transmit jitter compliance. * Added note on the differences between GPIO reported in Overview with User I/O numbers shown in the Quartus II software. * Updated template. July 2012 Altera Corporation 2.1 Added support for PCIe Gen2 x4 lane configuration (PCIe-compatible) Cyclone V Device Overview Send Feedback CV-51001 2013.12.26 Document Revision History Date Version 35 Changes June 2012 2.0 * Restructured the document. * Added the "Embedded Memory Capacity" and "Embedded Memory Configurations" sections. * Added Table 1, Table 3, Table 16, Table 19, and Table 20. * Updated Table 2, Table 4, Table 5, Table 6, Table 7, Table 8, Table 9, Table 10, Table 11, Table 12, Table 13, Table 14, Table 17, and Table 18. * Updated Figure 1, Figure 2, Figure 3, Figure 4, Figure 5, Figure 6, and Figure 10. * Updated the "FPGA Configuration and Processor Booting" and "Hardware and Software Development" sections. * Text edits throughout the document. February 2012 1.2 * Updated Table 1-2, Table 1-3, and Table 1-6. * Updated "Cyclone V Family Plan" on page 1-4 and "Clock Networks and PLL Clock Sources" on page 1-15. * Updated Figure 1-1 and Figure 1-6. November 2011 1.1 * Updated Table 1-1, Table 1-2, Table 1-3, Table 1-4, Table 1-5, and Table 1-6. * Updated Figure 1-4, Figure 1-5, Figure 1-6, Figure 1-7, and Figure 1-8. * Updated "System Peripherals" on page 1-18, "HPS-FPGA AXI Bridges" on page 1-19, "HPS SDRAM Controller Subsystem" on page 1-19, "FPGA Configuration and Processor Booting" on page 1-19, and "Hardware and Software Development" on page 1-20. * Minor text edits. October 2011 1.0 Initial release. Cyclone V Device Overview Send Feedback Altera Corporation