FF-LS482813562 - Honeywell - Product.Network

FF-LS Series

•

Industrial Safety Products

•115

WARNING

MISUSE OF DOCUMENTATION

• The information presented in this product sheet (or catalogue) is for reference only. DO NOT USE this document as system

installation information.

• Complete installation, operation and maintenance information is provided in the instructions supplied with each product.

Failure to comply with these instructions could result in death or serious injury.

FF-LS14

Type 4 miniature light curtain,

14 mm/0.55 in resolution

Designed for the protection of operators work stations

FF-LS14 Series

HANNOVER

SACHSEN-ANHALT

FEATURES

• Meets applicable parts of US OSHA

29CFR 1910.217, 1910.212 and ANSI

B11.1, B11.2, B11.19 1990 and RIA

15.06 regulations for Control reliability

• EC type examination certificate granted

by the TÜV

• Designed in compliance with the IEC/EN

61496 - parts 1 & 2 for Type 4

Electrosensitive Protective Equipment

(permanent self-checking equipment)

• Through-scan small profile sensing units

with separate control unit

• Minimum object detection capability:

ø14 mm / 0.55 in suitable for fingers

detection

• Scanning range from 0,2 m up to 3,5 m /

0.65 ft up to 11.48 ft.

• Protection heights: from 196 mm up to

744 mm / 7.72 in up to 29.31 in

• Global response time: less than 50 ms

• Power supply voltage: 24 Vac/dc

• Outputs: 2 guided contacts safety

relays

• Test input

• Automatic restart or start & restart

interlock

• Sealing: IP 65 (sensing units and

control unit)

• Immunity to ambient light: 50 000 Lux

max.

TYPICAL APPLICATIONS

• Paper-cutting machines

• Pick-and-place robots

• Light electronic assemblying machines

• Textile machines

• Leather presses

• Matching centres

The FF-LS14 equipment is an ultra-compact infrared multibeam device designed to protect

operators working on dangerous machines. The FF-LS14 equipment features are ideal for the

protection of work stations where space is critical such as paper-cutting machines or pick-

and-place robots. Thanks to a small resolution, it will spring into action even if a finger gets

too close: any intrusion will lead to the immediate stoppage of the moving part of the ma-

chine.

Each sensing unit is made up of a row of emitting circuits alternating with receiving circuits.

These circuits are housed in an extremely small aluminium extruded profile: the cross section

is only 23 mm x 35 mm / 0.90 in x 1.38 in, the smallest available on the market in its class. These

ultra-compact dimensions, backed by in-line connectors, allow the FF-LS14 to be mounted on

small machines or in other applications where light curtains were previously too large. Its small

resolution - the smallest on the market - allows the closest installation to the dangerous area,

thanks to no additional safety distance in the safety distance calculation formula (EN 999).

The permanent self-checking electronic process is based on a microprocessor technology and

meets the requirements of the IEC/EN 61496 - parts 1 & 2 European standards for Type 4

electrosensitive protective equipment. It has been granted the EC type examination certificate by

the TÜV.

The equipment consists of a pair of identical length sensing units, a separate control unit and a

pair of RS-485 connection cables. It is supplied with mounting brackets, a test rod and cable

glands for the terminal strip connections.

The two sensors are matched to each other by individual coding to reduce risk of cross talk with

other light curtains and to improve immunity to welding splashes.

The control unit supplies the sensing units, controls the correct operation of the scanning

circuits and transmits the resulting commands to the machine control circuitry through its

two relay outputs.

The equipment can operate according to two different modes selected with an internal selec-

tor: the automatic mode or the start & restart interlock mode.

In addition, the control unit is featured with a test input to trigger the output relays switching

and thus check the correct operation of the final switching devices whenever needed.

In case of failure, the control unit provides an acoustic signal and 6 different optical signals to

ease failure diagnostic.

Type 4

per pr EN 50100 - 1/2

Approved as

116 •

Industrial Safety Products

•

FF-LS Series

FF-LS14

4 / 0.154 / 0.15

Protected zone

220 Vac

115 Vac

24 Vdc

Power supply

(2)

Cable length: 10 m / 32.8 ft

35 / 1.38 (+0,5 / -0.0)

22,8 / 0.89

(+0,6 / -0,0)

Sensor B

Sensor A

240 / 9.45

43 / 1.69

30.75 /

1.21 29.25 /

1.15

226 / 8.90

140.0 / 5.51

145 / 5.71

146 / 5.75

160 / 6.30

96 / 3.78

78 / 3.07

40 /

1.57 35 /

1.38 25 /

0.98 25 /

0.98 20 /

0.78 20 /

0.78

20 /

0.78 25 /

0.98

160 / 6.30

60 / 2.36

160 / 6.30

30.75/

1.21

43 / 1.69

30/

1.18

30/

1.18

50/

1.97

0.70

Connector

RS-485

Type 4

per pr EN 50100 - 1/2

Approved as

HANNOVER

SACHSEN-ANHALT

FF-LS14FF-LS14

FF-LS14

•Type 4 according to IEC/EN 61496 - parts 1& 2

•ø14 mm / 0.55 in object detection capability

•Reduced dimensions (23 mm x 35 mm / 0.90 in x 1.38 in cross section)

Dimensions in millimeters / inches, meters / feet, weights in kg / lbs

Specifications Supply voltage 22 to 30 Vdc or 18 to 25 Vac

Current consumption < 300 mA

Output switching capacity

Main out 1 & out 2

: 4 A/250 Vac /

Lamp

: 4 A/42 V

Material

Sensors

: Aluminium profile •

Control unit

: Polycarbonate

Housing Size

Sensors:

23 mm x 35 mm x PH mm / 0.90 in x 1.38 in x PH in

Control unit:

50 mm x 160 mm x 240 mm / 2.36 in x 6.30 in x 9.45 in

Emission Modulated infrared light (880 mm)

Resolution ø14 mm / 0.55 in

Alignment tolerance According to IEC/EN 61496 - 2 standard

Operating temperature 0 °C to 55 °C / 32 °F to 131 °F

Sealing

Sensors and control unit

: IP 65

Electromagnetic immunity According to IEC 801-4: level IV/According to IEC 801-3 level III

Light immunity 50,000 Lux

Status indicators Lamps to be connected to outputs available on control units

Range 0,2 m to 3,5 m / 0.65 ft to 11.48 ft

Electrical wiring (delivered with the unit)

Sensors

: RS-485 cable/Pre-wired connectors (10 m / 32.8 ft)

Control unit

: Screw terminal

Sensors A and B have the same dimensions.

Ordering information (1)

FF-LS

ooo

Notes: Control unit

(4 mounting M4 holes) Power supplies (2)

(1) Each reference corresponds to the delivery

of a complete set: A/B sensors, control unit,

2 RS-485 cables (pre-wired 10 m / 32.8 in),

brackets,

8 cable glands and a ø14 mm / 0.55 in test rod.

(2) Power supply: The use of one of these

supplies brings the galvanic isolation which is

necessary for the system to be in compliance

with IEC/EN 61496-1 standard.

FF-LSZUS0605 (230 Vac / 24 Vdc)

FF-LSZUS0606 (115 Vac / 24 Vdc)

These power supplies must be ordered separately.

(3) Control unit and sensors.

Nominal Protection Height mm / in PH 196 / 7.72 378 / 14.89 561 / 22.10 744 / 29.31

Number of beams 16 32 48 64

Response time t1 < 50 ms < 50 ms < 50 ms < 50 ms

Weight of the device (3) kg / lbs 1,85 / 4.07 2,06 / 4.53 2,26 / 4.97 2,48 / 5.45

Number of

beams

Protection

height (PH)

(mm / in)

196 / 7.72

378 / 14.89

561 / 22.10

744 / 29.31

Model

196

378

561

744

FF-LS14

•

Industrial Safety Products

•117

FF-LS Series

Stopping

machine

circuitry (4)

1.1

1.2

2.1

2.2

Main

Out 1 Main

Out 2

X1 X2

Max. 4A

42 Vdc/Vac

OFF

COM

X1X1 X2

18-25 Vac

22-30 Vdc

Supply

Vin1 Vin2

Test

BROWN

GREEN

YELLOW

WHITE

BLACK

BROWN

GREEN

YELLOW

WHITE

BLA CK

RS485

Sensor A Sensor B

Stopping contacts

Indicators

(1)

Green lamp

Red lamp

(3) (2)

Restart

Vin 2

Vin 1

Buzzer

OFF

Buzzer

switch Function

switch

Supply

fuse

Output contact fuses

NSR-0605

Tool

Plunger

Safety distance

S: Minimum safety distance (mm / in)

t1:Response time of the light curtain (s)

t2:Stopping time of the equipment guarded by the light

curtain, including all mechanical, electromechanical and

electronic parts. (s)

H: Height of the detection zone above the floor (mm / in)

The safety distance between the protection field and the

dangerous zone should be large enough to ensure that if the

protection field is entered, the dangerous zone cannot be

reached before the hazardous movement is arrested. For the

safety distance, the following formula applies:

•Normal Approach

Europe (EN 999)

S ≥≥

≥≥

≥ 2000 (t1 + t2) (mm), with S ≥≥

≥≥

≥ 100 mm

(or S ≥≥

≥≥

≥ 78.8 (t1 + t2), with S ≥≥

≥≥

≥ 3.9 in

If the result of this calculation is greater or equal to 500 mm/

19.7 in, then use the following formula:

S ≥≥

≥≥

≥ 1600 (t1+ t2) (mm), with S ≥≥

≥≥

≥ 500 mm

(or S ≥≥

≥≥

≥ 63 (t1 + t2) (in), with S ≥≥

≥≥

≥ 19.7 in

US (OSHA 29 CFR 1910.217, ANSI B11.19 1990

Ds ≥≥

≥≥

≥ (t1 + t2) + 0.9315 (in) Ds = S

Optical and acoustic signals of the control unit As shown in the figure here

below, there are 7 LEDs on the

control unit. The green LEDs 1, 2

and 3 are constantly alight when

the supply voltage is present.

The system condition is indicated

by the yellow LEDs 4 and 6, the

red LEDs 5 and 7 and an acoustic

signal. This signal can be

switched on or off by the buzzer

switch on the PC-board.

Connection diagram (1) - Supply (to be ordered

separately): The use of one of these

supplies brings the galvanic isolation

which is necessary to the system for

a use conform to IEC/EN 61496 - 1

standard.

FF-LSZUS0605 (230 Vac / 24 Vdc),

FF-LSZUS0606 (115 Vac / 24 Vdc)

(2) - Test duration: The contact must

be closed during 100 ms as a

minimum.

(3) - The push-button must remain

closed during 200 ms at least. It

takes 500 ms for the system to

restart after releasing the push-

button.

(4) - If additional contacts are needed

or if the switching capacity must be

increased, use the connection

diagram given or an example.

118 •

Industrial Safety Products

•

FF-LS Series

FF-LS14

10 /

0.394

10 /

0.394

100 / 3.94

20 /

0.78

20 /

0.78

20 / 0.78

6 /

0.23 9,7 /

0.38 4,3 /

0.16

M3 ø3,5 / 0.13

3,5/

0.13

6,5/

0.25

1,5 / 0.05

0.23 6/

0.23

3,5 / 0.13

ø3,5 / 0.13

20 / 0.78 20 / 0.78

100 / 3.94

3,5/

0.13 3,5/

0.13

+1.1

1.2

2.1

2.2

FF-LS

control

unit

FSD

K2 K2

Start

push-button

Hold

Start Interlock

TEST X1 X2

Machine

control circuit

FSD

(1)

Straight bracket

Kit of 2 straight brackets for an installation parallel to the

sliding rail.

Right-angle bracket

Kit of 2 right-angle brackets for an installation perpendicular

to the sliding rail.

Note: All FF-LS equipment is delivered with both types of

brackets. The number of brackets available allows to fix one

bracket every 500 mm / 19.7 in along the profile.

Example of Installation

For a correct installation, brackets must be fixed on a plain

base in order to avoid profile deformation.

Accessories

FF-LSZKA0611: Connecting cable

One 10 m / 32.8 ft RS485 prewired cable for the connection of one sensing unit to the control unit.

Connection diagram example: Start/Restart interlock/Final Switching Device (FSD) monitoring

(please refer to EN 954 for electrical interface)

(1) RC (220 Ω + 22 µF)

for ac interface (or

varistors for dc

interfaces) increases

the life of contacts and

improves electrical

noise immunity.

FF-LSZMS720

FF-LSZMS730

Examples

Fixing

screw Fixing

screw

Plain base

Sliding

rail