LMK00301SQX/NOPB - NATIONAL SEMICONDUCTOR

LMV611 Single/LMV612 Dual/

LMV614 Quad

May 31, 2012

1.4 MHz, Low Power General Purpose, 1.8V Operational

Amplifiers

General Description

The LMV611/LMV612/LMV614 are single, dual, and quad low

voltage, low power Operational Amplifiers. They are designed

specifically for low voltage general purpose applications. Oth-

er important product characteristics are, rail to-rail input/out-

put, low supply voltage of 1.8V and wide temperature range.

The LMV611/LMV612/LMV614 input common mode extends

200mV beyond the supplies and the output can swing rail-to-

rail unloaded and within 30mV with 2kohm load at 1.8V sup-

ply. The LMV611/2/4 achieves a gain bandwidth of 1.4MHz

while drawing 100 uA (typ) quiescent current.

The industrial-plus temperature range of −40°C to 125°C al-

lows the LMV611/LMV612/LMV614 to accommodate a broad

range of extended environment applications.

The LMV611 is offered in the tiny 5-Pin SC70 package, the

LMV612 in space saving 8-Pin MSOP and SOIC, and the

LMV614 in 14-Pin TSSOP and SOIC. These small package

amplifiers offer an ideal solution for applications requiring

minimum PCB footprint. Applications with area constrained

PC board requirements include portable and battery operated

electronics.

Features

(Typical 1.8V Supply Values; Unless Otherwise Noted)

■Guaranteed 1.8V, 2.7V and 5V specifications

■Output swing

—w/600Ω load 80mV from rail

—w/2kΩ load 30mV from rail

■VCM 200mV beyond rails

■Supply current (per channel) 100μA

■Gain bandwidth product 1.4MHz

■Maximum VOS 4.0mV

■Temperature range −40°C to 125°C

Applications

■Consumer communication

■Consumer computing

■PDAs

■Audio pre-amp

■Portable/battery-powered electronic equipment

■Supply current monitoring

■Battery monitoring

Typical Application

30185616

LMV611 Single/LMV612 Dual/LMV614 Quad 1.4 MHz, Low Power General Purpose, 1.8V

Operational Amplifiers

Absolute Maximum Ratings (Note 1)

If Military/Aerospace specified devices are required,

please contact the Texas Instruments Sales Office/

Distributors for availability and specifications.

ESD Tolerance (Note 2)

Machine Model 200V

Human Body Model 2000V

Supply Voltage (V+–V −)6V

Differential Input Voltage ± Supply Voltage

Voltage at Input/Output Pins V++0.3V, V- -0.3V

Storage Temperature Range −65°C to 150°C

Junction Temperature (Note 4) 150°C

For soldering specifications:

see product folder at www.national.com and

www.national.com/ms/MS/MS-SOLDERING.pdf

Operating Ratings (Note 1)

Supply Voltage Range 1.8V to 5.5V

Temperature Range −40°C to 125°C

Thermal Resistance (θJA)

5-Pin SC70 414°C/W

5-Pin SOT23 265°C/W

8-Pin MSOP 235°C/W

8-Pin SOIC 175°C/W

14-Pin TSSOP 155°C/W

14-Pin SOIC 127°C/W

1.8V DC Electrical Characteristics

Unless otherwise specified, all limits guaranteed for TJ = 25°C. V+ = 1.8V, V − = 0V, VCM = V+/2, VO = V+/2 and

RL > 1 MΩ. Boldface limits apply at the temperature extremes. See (Note 10)

Symbol Parameter Condition Min

(Note 6)

Typ

(Note 5)

Max

(Note 6)

Units

VOS Input Offset Voltage LMV611 (Single) 1 4 mV

LMV612 (Dual)

LMV614 (Quad)

1 5.5 mV

TCVOS Input Offset Voltage Average

Drift

5.5 μV/°C

IBInput Bias Current 15 nA

IOS Input Offset Current 13 nA

ISSupply Current (per channel) 103 185 μA

CMRR Common Mode Rejection Ratio LMV611, 0 ≤ VCM ≤ 0.6V

1.4V ≤ VCM ≤ 1.8V (Note 8)

60 78

LMV612 and LMV614

0 ≤ VCM ≤ 0.6V

1.4V ≤ VCM ≤ 1.8V (Note 8)

55 76

−0.2V ≤ VCM ≤ 0V

1.8V ≤ VCM ≤ 2.0V

50 72

PSRR Power Supply Rejection Ratio 1.8V ≤ V+ ≤ 5V 100 dB

CMVR Input Common-Mode Voltage

Range

For CMRR

Range ≥ 50dB

TA = 25°C V− −0.2 −0.2 to 2.1 V+ +0.2

TA −40°C to 85°

V−V+

TA = 125°C V− +0.2 V+ −0.2

AVLarge Signal Voltage Gain

LMV611 (Single)

RL = 600Ω to 0.9V,

VO = 0.2V to 1.6V, VCM = 0.5V

77 101

RL = 2kΩ to 0.9V,

VO = 0.2V to 1.6V, VCM = 0.5V

80 105

Large Signal Voltage Gain

LMV612 (Dual)

LMV614 (Quad)

RL = 600Ω to 0.9V,

VO = 0.2V to 1.6V, VCM = 0.5V

75 90

RL = 2kΩ to 0.9V,

VO = 0.2V to 1.6V, VCM = 0.5V

78 100

VOOutput Swing RL = 600Ω to 0.9V

VIN = ±100mV

1.65 1.72

0.077 0.105

RL = 2kΩ to 0.9V

VIN = ±100mV

1.75 1.77

0.024 0.035

www.ti.com 2

LMV611 Single/LMV612 Dual/LMV614 Quad

Symbol Parameter Condition Min

(Note 6)

Typ

(Note 5)

Max

(Note 6)

Units

IOOutput Short Circuit Current

(Note 3)

Sourcing, VO = 0V

VIN = 100mV

Sinking, VO = 1.8V

VIN = −100mV

1.8V AC Electrical Characteristics

Unless otherwise specified, all limits guaranteed for TJ = 25°C. V+ = 1.8V, V − = 0V, VCM = V+/2, VO = V+/2 and RL > 1 MΩ.

Boldface limits apply at the temperature extremes. See (Note 10)

Symbol Parameter Conditions Min

(Note 6)

Typ

(Note 5)

Max

(Note 6)Units

SR Slew Rate (Note 7) 0.35 V/μs

GBW Gain-Bandwidth Product 1.4 MHz

ΦmPhase Margin 67 deg

GmGain Margin 7 dB

enInput-Referred Voltage Noise f = 10 kHz, VCM = 0.5V 60

inInput-Referred Current Noise f = 10 kHz 0.08

THD Total Harmonic Distortion f = 1kHz, AV = +1

RL = 600Ω, VIN = 1 VPP

0.023 %

Amp-to-Amp Isolation (Note 9) 123 dB

3 www.ti.com

LMV611 Single/LMV612 Dual/LMV614 Quad

2.7V DC Electrical Characteristics

Unless otherwise specified, all limits guaranteed for TJ = 25°C. V+ = 2.7V, V − = 0V, VCM = V+/2, VO = V+/2 and

RL > 1 MΩ. Boldface limits apply at the temperature extremes. See (Note 10)

Symbol Parameter Condition Min

(Note 6)

Typ

(Note 5)

Max

(Note 6)Units

VOS Input Offset Voltage LMV611 (Single) 1 4 mV

LMV612 (Dual)

LMV614 (Quad)

1 5.5 mV

TCVOS Input Offset Voltage Average

Drift

5.5 μV/°C

IBInput Bias Current 15 nA

IOS Input Offset Current 8 nA

ISSupply Current (per channel) 105 190 μA

CMRR Common Mode Rejection Ratio LMV611, 0 ≤ VCM ≤ 1.5V

2.3V ≤ VCM ≤ 2.7V (Note 8)

60 81

LMV612 and LMV614

0 ≤ VCM ≤ 1.5V

2.3V ≤ VCM ≤ 2.7V (Note 8)

55 80

−0.2V ≤ VCM ≤ 0V

2.7V ≤ VCM ≤ 2.9V

50 74

PSRR Power Supply Rejection Ratio 1.8V ≤ V+ ≤ 5V

VCM = 0.5V

100 dB

VCM Input Common-Mode Voltage

Range

For CMRR

Range ≥ 50dB

TA = 25°C V− −0.2 −0.2 to 3.0 V+ +0.2

TA = −40°C to

85°C

V−V+

TA = 125°C V− +0.2 V+ −0.2

AVLarge Signal Voltage Gain

LMV611 (Single)

RL = 600Ω to 1.35V,

VO = 0.2V to 2.5V

87 104

RL = 2kΩ to 1.35V,

VO = 0.2V to 2.5V

92 110

Large Signal Voltage Gain

LMV612 (Dual)

LMV614 (Quad)

RL = 600Ω to 1.35V,

VO = 0.2V to 2.5V

78 90

RL = 2kΩ to 1.35V,

VO = 0.2V to 2.5V

81 100

VOOutput Swing RL = 600Ω to 1.35V

VIN = ±100mV

2.55 2.62

0.083 0.110

RL = 2kΩ to 1.35V

VIN = ±100mV

2.65 2.675

0.025 0.04

IOOutput Short Circuit Current

(Note 3)

Sourcing, VO = 0V

VIN = 100mV

Sinking, VO = 0V

VIN = −100mV

www.ti.com 4

LMV611 Single/LMV612 Dual/LMV614 Quad

2.7V AC Electrical Characteristics

Unless otherwise specified, all limits guaranteed for TJ = 25°C. V+ = 2.7V, V − = 0V, VCM = 1.0V, VO = 1.35V and RL > 1 MΩ.

Boldface limits apply at the temperature extremes. See (Note 10)

Symbol Parameter Conditions Min

(Note 6)

Typ

(Note 5)

Max

(Note 6)

Units

SR Slew Rate (Note 7) 0.4 V/µs

GBW Gain-Bandwidth Product 1.4 MHz

ΦmPhase Margin 70 deg

GmGain Margin 7.5 dB

enInput-Referred Voltage Noise f = 10 kHz, VCM = 0.5V 57

inInput-Referred Current Noise f = 10 kHz 0.08

THD Total Harmonic Distortion f = 1kHz, AV = +1

RL = 600Ω, VIN = 1VPP

0.022 %

Amp-to-Amp Isolation (Note 9) 123 dB

5 www.ti.com

LMV611 Single/LMV612 Dual/LMV614 Quad

5V DC Electrical Characteristics

Unless otherwise specified, all limits guaranteed for TJ = 25°C. V+ = 5V, V − = 0V, VCM = V+/2, VO = V+/2 and

RL > 1 MΩ. Boldface limits apply at the temperature extremes. See (Note 10)

Symbol Parameter Condition Min

(Note 6)

Typ

(Note 5)

Max

(Note 6)

Units

VOS Input Offset Voltage LMV611 (Single) 1 4 mV

LMV612 (Dual)

LMV614 (Quad)

1 5.5 mV

TCVOS Input Offset Voltage Average

Drift

5.5 μV/°C

IBInput Bias Current 14 35 nA

IOS Input Offset Current 9 nA

ISSupply Current (per channel) 116 210 μA

CMRR Common Mode Rejection Ratio 0 ≤ VCM ≤ 3.8V

4.6V ≤ VCM ≤ 5.0V (Note 8)

60 86

−0.2V ≤ VCM ≤ 0V

5.0V ≤ VCM ≤ 5.2V

50 78

PSRR Power Supply Rejection Ratio 1.8V ≤ V+ ≤ 5V

VCM = 0.5V

100 dB

CMVR Input Common-Mode Voltage

Range

For CMRR

Range ≥ 50dB

TA = 25°C V− −0.2 −0.2 to 5.3 V+ +0.2

TA = −40°C to

85°C

V−V+

TA = 125°C V− +0.3 V+ −0.3

AVLarge Signal Voltage Gain

LMV611 (Single)

RL = 600Ω to 2.5V,

VO = 0.2V to 4.8V

88 102

RL = 2kΩ to 2.5V,

VO = 0.2V to 4.8V

94 113

Large Signal Voltage Gain

LMV612 (Dual)

LMV614 (Quad)

RL = 600Ω to 2.5V,

VO = 0.2V to 4.8V

81 90

RL = 2kΩ to 2.5V,

VO = 0.2V to 4.8V

85 100

VOOutput Swing RL = 600Ω to 2.5V

VIN = ±100mV

4.855 4.890

0.120 0.160

RL = 2kΩ to 2.5V

VIN = ±100mV

4.945 4.967

0.037 0.065

IOOutput Short Circuit Current

(Note 3)

LMV611, Sourcing, VO = 0V

VIN = 100mV

100

Sinking, VO = 5V

VIN = −100mV

5V AC Electrical Characteristics

Unless otherwise specified, all limits guaranteed for TJ = 25°C. V+ = 5V, V − = 0V, VCM = V+/2, VO = 2.5V and R L > 1 MΩ.

Boldface limits apply at the temperature extremes. See (Note 10)

Symbol Parameter Conditions Min

(Note 6)

Typ

(Note 5)

Max

(Note 6)

Units

SR Slew Rate (Note 7) 0.42 V/µs

GBW Gain-Bandwidth Product 1.5 MHz

ΦmPhase Margin 71 deg

GmGain Margin 8 dB

www.ti.com 6

LMV611 Single/LMV612 Dual/LMV614 Quad

Symbol Parameter Conditions Min

(Note 6)

Typ

(Note 5)

Max

(Note 6)

Units

enInput-Referred Voltage Noise f = 10 kHz, VCM = 1V 50

inInput-Referred Current Noise f = 10 kHz 0.08

THD Total Harmonic Distortion f = 1kHz, AV = +1

RL = 600Ω, VO = 1V PP

0.022 %

Amp-to-Amp Isolation (Note 9) 123 dB

Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is

intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics.

Note 2: Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of JEDEC)

Field-Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC).

Note 3: Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the

maximum allowed junction temperature of 150°C. Output currents in excess of 45mA over long term may adversely affect reliability.

Note 4: The maximum power dissipation is a function of TJ(MAX), θJA and TA. The maximum allowable power dissipation at any ambient temperature is

PD = (TJ(MAX) – TA)/ θJA. All numbers apply for packages soldered directly onto a PC Board.

Note 5: Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will

also depend on the application and configuration. The typical values are not tested and are not guaranteed on shipped production material.

Note 6: All limits are guaranteed by testing or statistical analysis.

Note 7: Connected as voltage follower with input step from V− to V+. Number specified is the slower of the positive and negative slew rates.

Note 8: For guaranteed temperature ranges, see Input Common-Mode Voltage Range specifications.

Note 9: Input referred, RL = 100kΩ connected to V+/2. Each amp excited in turn with 1kHz to produce VO = 3VPP (For Supply Voltages <3V, VO = V+).

Note 10: Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating

of the device such that TJ = TA. No guarantee of parametric performance is indicated in the electrical tables under conditions of internal self-heating where TJ >

TA. See Applications section for information of temperature derating of the device. Absolute Maximum Ratings indicated junction temperature limits beyond which

the device may be permanently degraded, either mechanically or electrically.

7 www.ti.com

LMV611 Single/LMV612 Dual/LMV614 Quad

Connection Diagrams

5-Pin SC70-5/SOT23-5

(LMV611)

30185602

Top View

8-Pin MSOP/SOIC

(LMV612)

30185611

Top View

14-Pin TSSOP/SOIC

(LMV614)

30185612

Top View

Ordering Information

Package Part Number Packaging Marking Transport Media NSC Drawing

5-Pin SC70 LMV611MG AVA 1k Units Tape and Reel MAA05A

LMV611MGX 3k Units Tape and Reel

5-Pin SOT23 LMV611MF AE9A 1k Units Tape and Reel MF05A

LMV611MFX 3k Units Tape and Reel

8-Pin MSOP LMV612MM AD9A 1k Units Tape and Reel MUA08A

LMV612MMX 3.5k Units Tape and Reel

8-Pin SOIC LMV612MA LMV612MA Rails M08A

LMV612MAX 2.5k Units Tape and Reel

14-Pin TSSOP LMV614MT LMV614MT Rails MTC14

LMV614MTX 2.5k Units Tape and Reel

14-Pin SOIC LMV614MA LMV614MA Rails M14A

LMV614MAX 2.5k Units Tape and Reel

www.ti.com 8

LMV611 Single/LMV612 Dual/LMV614 Quad

Typical Performance Characteristics Unless otherwise specified, VS = +5V, single supply, TA = 25°C.

Supply Current vs. Supply Voltage (LMV611)

30185622

Sourcing Current vs. Output Voltage

30185625

Sinking Current vs. Output Voltage

30185628

Output Voltage Swing vs. Supply Voltage

30185649

Output Voltage Swing vs. Supply Voltage

30185650

Gain and Phase vs. Frequency

30185614

9 www.ti.com

LMV611 Single/LMV612 Dual/LMV614 Quad

Gain and Phase vs. Frequency

30185615

Gain and Phase vs. Frequency

30185609

Gain and Phase vs. Frequency

30185610

CMRR vs. Frequency

30185639

PSRR vs. Frequency

30185656

Input Voltage Noise vs. Frequency

30185658

www.ti.com 10

LMV611 Single/LMV612 Dual/LMV614 Quad

Input Current Noise vs. Frequency

30185666

THD vs. Frequency

30185667

THD vs. Frequency

30185668

Slew Rate vs. Supply Voltage

30185669

Small Signal Non-Inverting Response

30185670

Small Signal Non-Inverting Response

30185671

11 www.ti.com

LMV611 Single/LMV612 Dual/LMV614 Quad

Small Signal Non-Inverting Response

30185672

Large Signal Non-Inverting Response

30185673

Large Signal Non-Inverting Response

30185674

Large Signal Non-Inverting Response

30185675

Short Circuit Current vs. Temperature (Sinking)

30185676

Short Circuit Current vs. Temperature (Sourcing)

30185677

www.ti.com 12

LMV611 Single/LMV612 Dual/LMV614 Quad

Offset Voltage vs. Common Mode Range

30185636

Offset Voltage vs. Common Mode Range

30185637

Offset Voltage vs. Common Mode Range

30185638

Application Note

INPUT AND OUTPUT STAGE

The rail-to-rail input stage of this family provides more flexi-

bility for the designer. The LMV611/LMV612/LMV614 use a

complimentary PNP and NPN input stage in which the PNP

stage senses common mode voltage near V− and the NPN

stage senses common mode voltage near V+. The transition

from the PNP stage to NPN stage occurs 1V below V+. Since

both input stages have their own offset voltage, the offset of

the amplifier becomes a function of the input common mode

voltage and has a crossover point at 1V below V+.

This VOS crossover point can create problems for both DC and

AC coupled signals if proper care is not taken. Large input

signals that include the VOS crossover point will cause distor-

tion in the output signal. One way to avoid such distortion is

to keep the signal away from the crossover. For example, in

a unity gain buffer configuration and with VS = 5V, a 5V peak-

to-peak signal will contain input-crossover distortion while a

3V peak-to-peak signal centered at 1.5V will not contain input-

crossover distortion as it avoids the crossover point. Another

way to avoid large signal distortion is to use a gain of −1 circuit

which avoids any voltage excursions at the input terminals of

the amplifier. In that circuit, the common mode DC voltage

can be set at a level away from the VOS cross-over point. For

small signals, this transition in VOS shows up as a VCM de-

pendent spurious signal in series with the input signal and can

effectively degrade small signal parameters such as gain and

common mode rejection ratio. To resolve this problem, the

small signal should be placed such that it avoids the VOS

crossover point. In addition to the rail-to-rail performance, the

output stage can provide enough output current to drive

600Ω loads. Because of the high current capability, care

should be taken not to exceed the 150°C maximum junction

temperature specification.

INPUT BIAS CURRENT CONSIDERATION

The LMV611/LMV612/LMV614 family has a complementary

bipolar input stage. The typical input bias current (IB) is 15nA.

The input bias current can develop a significant offset voltage.

This offset is primarily due to IB flowing through the negative

feedback resistor, RF. For example, if IB is 50nA and RF is

100kΩ, then an offset voltage of 5mV will develop (VOS = IB x

RF). Using a compensation resistor (RC), as shown in Figure

1, cancels this effect. But the input offset current (IOS) will still

contribute to an offset voltage in the same manner.

13 www.ti.com

LMV611 Single/LMV612 Dual/LMV614 Quad

30185659

FIGURE 1. Canceling the Offset Voltage due to Input Bias

Current

Typical Applications

HIGH SIDE CURRENT SENSING

The high side current sensing circuit (Figure 2) is commonly

used in a battery charger to monitor charging current to pre-

vent over charging. A sense resistor RSENSE is connected to

the battery directly. This system requires an op amp with rail-

to-rail input. The LMV611/LMV612/LMV614 are ideal for this

application because its common mode input range goes up

to the rail.

30185616

FIGURE 2. High Side Current Sensing

HALF-WAVE RECTIFIER WITH RAIL-TO-GROUND

OUTPUT SWING

Since the LMV611/LMV612/LMV614 input common mode

range includes both positive and negative supply rails and the

output can also swing to either supply, achieving half-wave

rectifier functions in either direction is an easy task. All that is

needed are two external resistors; there is no need for diodes

or matched resistors. The half wave rectifier can have either

positive or negative going outputs, depending on the way the

circuit is arranged.

In Figure 3 the circuit is referenced to ground, while in Figure

4 the circuit is biased to the positive supply. These configu-

rations implement the half wave rectifier since the LMV611/

LMV612/LMV614 can not respond to one-half of the incoming

waveform. It can not respond to one-half of the incoming be-

cause the amplifier can not swing the output beyond either

rail therefore the output disengages during this half cycle.

During the other half cycle, however, the amplifier achieves a

half wave that can have a peak equal to the total supply volt-

age. RI should be large enough not to load the LMV611/

LMV612/LMV614.

www.ti.com 14

LMV611 Single/LMV612 Dual/LMV614 Quad

30185607 30185606

30185608

FIGURE 3. Half-Wave Rectifier with Rail-To-Ground Output Swing Referenced to Ground

30185604

30185603

30185605

FIGURE 4. Half-Wave Rectifier with Negative-Going Output Referenced to VCC

INSTRUMENTATION AMPLIFIER WITH RAIL-TO-RAIL

INPUT AND OUTPUT

Some manufactures make a non-“rail-to-rail”-op amp rail-to-

rail by using a resistive divider on the inputs. The resistors

divide the input voltage to get a rail-to-rail input range. The

problem with this method is that it also divides the signal, so

in order to get the obtained gain, the amplifier must have a

higher closed loop gain. This raises the noise and drift by the

internal gain factor and lowers the input impedance. Any mis-

match in these precision resistors reduces the CMRR as well.

The LMV611/LMV612/LMV614 is rail-to-rail and therefore

doesn’t have these disadvantages.

Using three of the LMV611/LMV612/LMV614 amplifiers, an

instrumentation amplifier with rail-to-rail inputs and outputs

can be made as shown in Figure 5.

In this example, amplifiers on the left side act as buffers to the

differential stage. These buffers assure that the input

impedance is very high and require no precision matched re-

sistors in the input stage. They also assure that the difference

amp is driven from a voltage source. This is necessary to

maintain the CMRR set by the matching R1-R2 with R3-R4.

The gain is set by the ratio of R2/R1 and R3 should equal R1

and R4 equal R2. With both rail-to-rail input and output ranges,

the input and output are only limited by the supply voltages.

Remember that even with rail-to-rail outputs, the output can

not swing past the supplies so the combined common mode

voltages plus the signal should not be greater that the sup-

plies or limiting will occur. For additional applications, see

National Semiconductor application notes AN–29, AN–31,

AN–71, and AN–127.

30185613

FIGURE 5. Rail-to-rail Instrumentation Amplifier

15 www.ti.com

LMV611 Single/LMV612 Dual/LMV614 Quad

Simplified Schematic

30185601

www.ti.com 16

LMV611 Single/LMV612 Dual/LMV614 Quad

Physical Dimensions inches (millimeters) unless otherwise noted

5-Pin SC70

NS Package Number MAA05A

5-Pin SOT23

NS Package Number MF05A

17 www.ti.com

LMV611 Single/LMV612 Dual/LMV614 Quad

8-Pin MSOP

NS Package Number MUA08A

8-Pin SOIC

NS Package Number M08A

www.ti.com 18

LMV611 Single/LMV612 Dual/LMV614 Quad

14-Pin TSSOP

NS Package Number MTC14

14-Pin SOIC

NS Package Number M14A

19 www.ti.com

LMV611 Single/LMV612 Dual/LMV614 Quad

Notes

LMV611 Single/LMV612 Dual/LMV614 Quad 1.4 MHz, Low Power General Purpose, 1.8V

Operational Amplifiers

www.ti.com

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,

and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should

obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are

sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.

TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard

warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where

mandated by government requirements, testing of all parameters of each product is not necessarily performed.

TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and

applications using TI components. To minimize the risks associated with customer products and applications, customers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,

or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information

published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a

warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual

property of the third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied

by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive

business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional

restrictions.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all

express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not

responsible or liable for any such statements.

TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably

be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing

such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and

acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products

and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be

provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in

such safety-critical applications.

TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are

specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military

specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at

the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.

TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are

designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated

products in automotive applications, TI will not be responsible for any failure to meet such requirements.

Following are URLs where you can obtain information on other Texas Instruments products and application solutions:

Products Applications

Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive

Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications

Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers

DLP®Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps

DSP dsp.ti.com Energy and Lighting www.ti.com/energy

Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial

Interface interface.ti.com Medical www.ti.com/medical

Logic logic.ti.com Security www.ti.com/security

Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense

Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video

RFID www.ti-rfid.com

OMAP Mobile Processors www.ti.com/omap

Wireless Connectivity www.ti.com/wirelessconnectivity

TI E2E Community Home Page e2e.ti.com

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265