Mini-Circuits - Specification for Amplifier - MAR-6 Amplifier print this page MAR-6 Frequency GAIN, dB MHz fL - fU Min. Maximum Power, dBm Dynamic Range VSWR Absolute Maximum Rating DC Power Thermal resistance Ojc Output Input NF IP3 CurIn Out I P Device C/W (1 dB (no dB dBm rent Typ. Typ. (mA) (mW) Volt(V.) Comp.) damage) Typ. Typ. (mA) DC-2000 9.00 +2.00 +13.00 3.00 14.50 1.50 1.40 50.00 200.00 16.00 Lw=low range(fL to fU/2) U=upper range(fU/2 to fU) 1 3 3 2,4 110.00 Notes: Pin Connections Port RF in RF Out DC Case GND Not Used cb 3.50 * Minimum gain at highest frequency. Full temperature range, except room temperature for Dash-4 models. - * Conditionally stable, source and load VSWR<5:1 required. Potentially unstable with very high VSWR terminations. * Thermal resistance Ojc is from hottest junction in the device to the mounting surface of the leads. * Model number designated by alphanumeric code marking. * Permanent damage may occur if any of these limits are exceeded. These ratings are not intended for continuous normal operation. * For Amplifier Selection Guide, please click here. For Amplifier Environmental Specifications, please click here. * For Surface Mount Environmental Specifications, please click here. Re-flow soldering information is available in "Surface Mount" article. * Low frequency cutoff determined by external coupling capacitors. * Frequency at which output power, NF and IP3 are specified: 500 MHz. * Typical Biasing Configuration ERA/MAR/MAV/RAM/VAM Case Style - VV105 (inch,mm ) weight: 0.015 grams. A B C D E F G H J .085 .060 .008 .020 .250 .012 .025 2.159 1.524 0.203 0.508 6.350 0.305 0.635 K L M N P Q R S T Tolerance: .x .1 .xx .03 .xxx .015 inch. Material and Finish: Case material: plastic. Lead finish: tin-lead plate or tin plate. Marking: * Prefix letter (optional) designates assembly location. * Supply voltage must be connected to pin 3 through a bias resistor in order to prevent damage. See Biasing MMIC Amplifiers. Reliability predictions are applicable at specified current and normal operating conditions. * Aqueous washable. * General Quality Control Procedures and Environmental Specifications are given in Mini- Circuits Guarantees Quality. Hi-Rel, MIL description are given in Hi-Rel and MIL http://www.minicircuits.com/cgi-bin/spec?cat=amplifier&model=MAR-6&pix=vv105.gif&bv=4 (1 of 2) [7/1/2004 5:42:59 AM] Mini-Circuits - Specification for Amplifier - MAR-6 RF input lead (1) identified by one or both of the following at factory option: (a) diagonally cut lead, which may be 45(ref) in either direction; (b) orientation mark on the case. Model dash number identified by color dot or alphanumeric code on case. See specification data sheet. Special Tolerances: Lead width .010 inch; lead thickness .003 inch. * Prices and Specifications subjects to change without notice. Typical Performance Data FREQ (MHz) S11 (Input Return Loss) S 21 (Power Gain) S12 (Isolation Out- S22 (Output Return in) Loss) dB Mag Ang dB Ang dB Mag Ang dB Mag Ang 100.00 -27.96 0.04 171.00 20.10 171.00 -22.50 0.75 5.00 -27.96 0.04 -30.00 500.00 -26.02 0.05 -105.00 18.70 138.00 -21.30 0.09 21.00 -20.00 0.10 -104.00 1000.00 -17.72 0.13 -118.00 16.40 107.00 -18.80 0.12 28.00 -17.08 0.14 -150.00 1500.00 -13.56 0.21 -140.00 14.10 84.00 -17.10 0.14 28.00 -16.48 0.15 180.00 2000.00 -10.75 0.29 -163.00 12.00 65.00 -15.80 0.16 26.00 -15.92 0.16 157.00 2500.00 -9.37 0.34 -176.00 10.30 3000.00 -7.74 0.41 169.00 8.70 3500.00 -6.74 0.46 157.00 7.20 55.00 42.00 30.00 -15.20 0.17 28.00 -15.92 0.16 150.00 -14.80 0.18 25.00 -16.48 0.15 143.00 -14.20 0.19 22.00 -17.72 0.13 144.00 4000.00 -6.20 0.49 146.00 18.00 -13.80 0.20 20.00 -20.00 0.10 156.00 6.10 Back http://www.minicircuits.com/cgi-bin/spec?cat=amplifier&model=MAR-6&pix=vv105.gif&bv=4 (2 of 2) [7/1/2004 5:42:59 AM] i2 Technologies US, Inc. 15445 Innovation Drive San Diego, CA 92128 i2 Technologies US, Inc. HTML Pages converted to PDF Document This document contain component information from the manufacturer's website which are not available in a revision controlled document from the manufacturer. To facilitate the addition of these parts into the Electronics Database, we are converting the HTML pages related to that part, from the manufacturer's website into Adobe PDF format. The contents of this document is based on the information provided on the manufacturer's website, therefore the information may have been changed by the manufacturer since this was created. Powering the Bottom Line (R)