SM30 Series 30 mm Barrel Sensor Opposed-Mode Infrared Photoelectric Sensors for Especially Demanding Applications * Stainless steel or plastic barrel models * Very high excess gain; 150 m (500 ft) sensing range; 880 nm Infrared LED * Positive sealing eliminates even capillary leakage; lens is quad-ring sealed; exceeds NEMA 6P (IP67) ratings - ideal for equipment wash-down environments * EZ-BEAM(R) technology provides reliable sensing without the need for adjustment * Modulation frequency "A" is standard; frequencies "B" and "C" also available for preventing crosstalk in multiple-sensor applications (emitter and opposed receiver frequencies must match) * AC- and DC-operated receiver models available; emitters feature Universal voltage * Range for all models: 150 m (500 ft). See page 3 for performance curves. Modulation Frequency* A B Emitter Models C SMA30PEL SMA30PELB SMA30PELC SMA30PELQD SMA30PELQDB SMA30PELQDC SMA30SEL SMA30SELB SMA30SELC SMA30SELQD SMA30SELQDB SMA30SELQDC SM30PRL SM30PRLB SM30PRLC SM30PRLQD SM30PRLQDB SM30PRLQDC SM30SRL SM30SRLB SM30SRLC SM30SRLQD SM30SRLQDB SM30SRLQDC SM2A30PRL SM2A30PRLB SM2A30PRLC SM2A30PRLQD SM2A30PRLQDB SM2A30PRLQDC SM2A30SRL SM2A30SRLB SM2A30SRLC SM2A30SRLQD SM2A30SRLQDB SM2A30SRLQDC SM2A30PRLNC SM2A30PRLNCB SM2A30PRLNCC SM2A30PRLNCQD SM2A30PRLNCQDB SM2A30PRLNCQDC SM2A30SRLNC SM2A30SRLNCB SM2A30SRLNCC SM2A30SRLNCQD SM2A30SRLNCQDB SM2A30SRLNCQDC Housing Plastic Stainless Steel Cable** Supply Power Output Type Universal: 12 to 240V ac, 10 to 30V dc - 10 to 30V dc Bi-ModalTM NPN or PNP 2 m (6.5') 2-wire Cable 3-pin Mini-style QD 2 m (6.5') 3-wire Cable 3-pin Mini-style QD DC Receivers Plastic Stainless Steel 2 m (6.5') 4-wire Cable 4-pin Mini-style QD 2 m (6.5') 4-wire Cable 4-pin Mini-style QD AC Receivers Plastic Stainless Steel Plastic Stainless Steel 2 m (6.5') 2-wire Cable SPST Solid-state, L.O. 3-pin Mini-style QD 2 m (6.5') 3-wire Cable 3-pin Mini-style QD 2 m (6.5') 2-wire Cable 3-pin Mini-style QD 2 m (6.5') 3-wire Cable 24 to 240V ac SPST Solid-state, D.O. 3-pin Mini-style QD * Any emitter and receiver shown here can be used together, if they have the same modulation frequency. ** Standard 2 m (6.5 ft) cable and integral QD models are listed. A model with a QD connector requires a mating cable; see page 4. To order the 9 m (30 ft) cable: add suffix "W/30" following the Frequency suffix of any cable model (e.g., SM30PRLBW/30). AC models with QD require SM30CC model cables; see page 4. WARNING . . . Not To Be Used for Personnel Protection Never use these products for personnel protection. Doing so could lead to serious injury or death. These devices do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety applications. A device failure or malfunction can cause either an energized or de-energized output condition. Consult your current Banner Safety Products catalog for safety products that meet OSHA, ANSI, and IEC standards for personnel protection. Printed in USA Apr 2013 P/N 03541 Rev. E SM30 Series 30 mm Barrel Sensor Specifications Supply Voltage and Current Emitters: 12 to 240V ac (50/60 Hz) or 10-30V dc at 20 mA, 10% maximum ripple DC Receivers: 10 to 30V dc at 10 mA maximum (exclusive of load); 10% maximum ripple AC Receivers: 24 to 240V ac (50/60 Hz) Supply Protection Circuitry Protected against reverse polarity and transient voltages Output Configuration DC Receivers: Bi-ModalTM output (PNP sourcing or NPN sinking). Selection of light/dark operate and sourcing or sinking configuration dependent on hookup. AC Receivers: SPST solid-state switch; light operate (LO) or dark operate (DO) dependent on model. Output Rating DC Receivers: 250 mA continuous Output saturation voltage (PNP & NPN configuration) < 1 volt at 10 mA and < 2 volts at 250 mA Off-state leakage current < 10 microamps AC Receivers: Maximum steady-state load capability is 500 mA Inrush capability: 10 amps for 1 second (non-repeating) Off-state leakage: current < 1.7 mA rms On-state voltage drop: < 3.5 volts rms across a 500 mA load; < 5 volts rms across a 15 mA load Output Protection Circuitry Outputs of dc receivers are short circuit protected Output Response Time 10 milliseconds on/off Repeatability "A" frequency models: 1 ms "B" frequency models: 1.5 ms "C" frequency models: 2.3 ms Indicators Internal red LED, visible through the lens or from side of the sensor. Emitters: Red "Power ON" indicator LED DC Receivers: Lights whenever receiver sees its modulated light source AC Receivers: Lights whenever receiver's output is conducting Construction Fully epoxy-encapsulated tubular threaded housing, positive sealed at both ends, quad-ring sealed acrylic lens. Plastic models: 30 mm diameter thermoplastic polyester housing and jam nuts. Stainless Steel models: 30 mm diameter 303 stainless steel housing and jam nuts. Environmental Rating Exceeds NEMA 6P and IEC IP67 standards Connections PVC-jacketed 2 m or 9 m cables or Mini-style quick-disconnect (QD) fitting are available. QD cables are ordered separately. See page 4. Operating Conditions Temperature: -40 to +70 C (-40 to +158 F) Relative humidity: 90% at 50 C (non-condensing) Certifications Dimensions Cabled Models QD Models Jam Nuts (2 Provided) Jam Nuts (2 Provided) Alignment Indicator (Receivers) Alignment Indicator (Receivers) M30 x 1.5 Thread M30 x 1.5 Thread 102 mm (4.0") 2 P/N 03541 Rev. E 114 mm (4.5") Banner Engineering Corp. * Minneapolis, MN U.S.A www.bannerengineering.com * Tel: 763.544.3164 SM30 Series 30 mm Barrel Sensor Performance Curves Excess Gain Curve Beam Pattern 100000 SM30 Series Opposed Mode 10000 E X C E S S 1500 mm SM30 Series 60 in 1000 mm Opposed Mode 40 in 500 mm G A I N 20 in 0 1000 100 0 500 mm 20 in 1000 mm 40 in 1500 mm 60 in 10 0 45 m 150 ft 90 m 300 ft 180 m 600 ft 225 m 750 ft DISTANCE 1 1m 3.3 ft 135 m 450 ft 10 m 33 ft 100 m 330 ft 1000 m 3300 ft DISTANCE Hookups Emitters - Cabled Emitters - QD bn 10-30V dc or 12-240V ac bu gn* AC Receivers - Cabled rd/bk AC Receivers - QD rd/bk bn rd/wh 10-30V dc or 12-240V ac bu Load 24-240V ac rd/wh gn* gn* NOTE: A C emitters are not polarity-sensitive when powered by dc voltage. For QD listed on page 4 in order to match cable NOTE: The green wire must be connected to emitters, use aSM30CC model cables earth ground whenever model with a stainless colors. steel housing is powered by ac voltage 24-240V ac Load gn* NOTE: The green wire must be connected to earth ground whenever a model with a stainless steel housing is powered by ac voltage NOTE: The green wire must be connected to earth ground whenever a model with a stainless steel housing is powered by ac voltage *Connect green wire to earth ground whenever a stainless steel model is powered by ac voltage. (Cabled plastic models have no green wire.) DC Receivers - NPN bu - 10-30V dc + bn bk DC Receivers - PNP wh wh Load Light Operate wh bu - 10-30V dc + bn bk Load Dark Operate wh bu + 10-30V dc - bn bk Load Light Operate bu + 10-30V dc - bn bk Load Dark Operate NOTE: Where QD hookups only are shown, cabled model hookups are functionally identical. Banner Engineering Corp. * Minneapolis, MN U.S.A www.bannerengineering.com * Tel: 763.544.3164 P/N 03541 Rev. E3 SM30 Series 30 mm Barrel Sensor Quick-Disconnect (QD) Cables Style Model Length 3-pin Mini-Style SM30CC-306 SM30CC-312 2 m (6.5') 4 m (12') Connector Use with Emitters and AC receivers 4-pin Mini-Style 2 m (6.5') 4 m (12') 9 m (30') White Description APG30S Kit includes: a thread-on stainless steel housing, a flat glass lens, two quad-ring seals, plus 3 round and 3 slotted aperture disks Male Pinout Red/Black Black DC receivers Apertures Model Male Pinout Green Red/White Straight MBCC-406 MBCC-412 MBCC-430 Pinout Brown Blue Mounting Brackets SMB30A * 30 mm, 12-gauge, stainless steel, right-angle bracket with a curved mounting slot for versatile orientation * Clearance for M6 (1/4") hardware SMB30C * 30 mm split clamp bracket * Black reinforced thermoplastic polyester * Includes stainless steel mounting hardware SMB30MM * 30 mm, 12-gauge, stainless steel, right-angle bracket with curved mounting slots for versatile orientation * Clearance for M6 (1/4") hardware SMB30SC * 30 mm swivel bracket * Black reinforced thermoplastic polyester * Includes stainless steel mounting and swivel locking hardware Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application of the Banner product. THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. P/N 03541 Rev. E Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN USA 55441 * Phone: 763.544.3164 * www.bannerengineering.com * Email: sensors@bannerengineering.com