MX29LV320MT/B FEATURES 32M-BIT [4M x 8/2M x 16] SINGLE VOLTAGE 3V ONLY FLASH MEMORY GENERAL FEATURES * Single Power Supply Operation - 2.7 to 3.6 volt for read, erase, and program operations * 4,194,304 x 8 / 2,097,152 x 16 switchable * Sector structure - 8KB (4KW) x 8 and 64KB(32KW) x 63 * Sector Protection/Chip Unprotect - Provides sector group protect function to prevent program or erase operation in the protected sector group - Provides chip unprotect function to allow code changes - Provides temporary sector group unprotect function for code changes in previously protected sector groups * Secured Silicon Sector - Provides a 128-word OTP area for permanent, secure identification - Can be programmed and locked at factory or by customer * Latch-up protected to 250mA from -1V to VCC + 1V * Low VCC write inhibit is equal to or less than 1.5V * Compatible with JEDEC standard - Pin-out and software compatible to single power supply Flash * Minimum 100,000 erase/program cycle * 20-year data retention SOFTWARE FEATURES * Support Common Flash Interface (CFI) - Flash device parameters stored on the device and provide the host system to access * Program Suspend/Resume - Suspend program operation to read other sectors * Erase Suspend/Erase Resume - Suspends sector erase operation to read data from or program data to another sector which is not being erased * Status Reply - Data# polling & Toggle bits provide detection of program and erase operation completion HARDWARE FEATURES * Ready/Busy (RY/BY#) Output - Provides a hardware method of detecting program and erase operation completion * Hardware Reset (RESET#) Input - Provides a hardware method to reset the internal state machine to read mode * WP#/ACC input - Write protect (WP#) function allows protection of two outermost boot sectors, regardless of sector protect status - ACC (high voltage) accelerates programming time for higher throughput during system PERFORMANCE * High Performance - Fast access time: 70R/90ns - Page read time: 25ns - Sector erase time: 0.5s (typ.) - Effective write buffer word programming time: 22us - 4 word/8 byte page read buffer - 16 word/ 32 byte write buffer: reduces programming time for multiple-word/byte updates * Low Power Consumption - Active read current: 18mA(typ.) - Active write current: 50mA(typ.) - Standby current: 20uA(typ.) PACKAGE * 44-pin SOP * 48-pin TSOP * 48-ball CSP GENERAL DESCRIPTION The MX29LV320MT/B is a 32-mega bit Flash memory organized as 4M bytes of 8 bits or 2M bytes of 16 bits. MXIC's Flash memories offer the most cost-effective and reliable read/write non-volatile random access memory. The MX29LV320MT/B is packaged in 44-pin SOP, 48pin TSOP and 48-ball CSP. It is designed to be reprogrammed and erased in system or in standard EPROM programmers. The standard MX29LV320MT/B offers access time as fast as 70ns, allowing operation of high-speed microprocessors without wait states. To eliminate bus contention, the MX29LV320MT/B has separate chip enable (CE#) and output enable (OE#) controls. MXIC's Flash memories augment EPROM functionality with in-circuit electrical erasure and programming. The P/N:PM1129 REV. 1.1, JUL. 14, 2005 1 MX29LV320MT/B MX29LV320MT/B uses a command register to manage this functionality. controlled internally within the device. MXIC Flash technology reliably stores memory contents even after 100,000 erase and program cycles. The MXIC cell is designed to optimize the erase and program mechanisms. In addition, the combination of advanced tunnel oxide processing and low internal electric fields for erase and programming operations produces reliable cycling. The MX29LV320MT/B uses a 2.7V to 3.6V VCC supply to perform the High Reliability Erase and auto Program/ Erase algorithms. AUTOMATIC SECTOR ERASE The MX29LV320MT/B is sector(s) erasable using MXIC's Auto Sector Erase algorithm. Sector erase modes allow sectors of the array to be erased in one erase cycle. The Automatic Sector Erase algorithm automatically programs the specified sector(s) prior to electrical erase. The timing and verification of electrical erase are controlled internally within the device. The highest degree of latch-up protection is achieved with MXIC's proprietary non-epi process. Latch-up protection is proved for stresses up to 100 milliamperes on address and data pin from -1V to VCC + 1V. AUTOMATIC ERASE ALGORITHM MXIC's Automatic Erase algorithm requires the user to write commands to the command register using standard microprocessor write timings. The device will automatically pre-program and verify the entire array. Then the device automatically times the erase pulse width, provides the erase verification, and counts the number of sequences. A status bit toggling between consecutive read cycles provides feedback to the user as to the status of the programming operation. AUTOMATIC PROGRAMMING The MX29LV320MT/B is byte/word/page programmable using the Automatic Programming algorithm. The Automatic Programming algorithm makes the external system do not need to have time out sequence nor to verify the data programmed. The typical chip programming time at room temperature of the MX29LV320MT/B is less than 31.5 seconds. Register contents serve as inputs to an internal statemachine which controls the erase and programming circuitry. During write cycles, the command register internally latches address and data needed for the programming and erase operations. During a system write cycle, addresses are latched on the falling edge, and data are latched on the rising edge of WE# . AUTOMATIC PROGRAMMING ALGORITHM MXIC's Automatic Programming algorithm require the user to only write program set-up commands (including 2 unlock write cycle and A0H) and a program command (program data and address). The device automatically times the programming pulse width, provides the program verification, and counts the number of sequences. A status bit similar to DATA# polling and a status bit toggling between consecutive read cycles, provide feedback to the user as to the status of the programming operation. MXIC's Flash technology combines years of EPROM experience to produce the highest levels of quality, reliability, and cost effectiveness. The MX29LV320MT/B electrically erases all bits simultaneously using FowlerNordheim tunneling. The bytes are programmed by using the EPROM programming mechanism of hot electron injection. During a program cycle, the state-machine will control the program sequences and command register will not respond to any command set. During a Sector Erase cycle, the command register will only respond to Erase Suspend command. After Erase Suspend is completed, the device stays in read mode. After the state machine has completed its task, it will allow the command register to respond to its full command set. AUTOMATIC CHIP ERASE The entire chip is bulk erased using 50 ms erase pulses according to MXIC's Automatic Chip Erase algorithm. Typical erasure at room temperature is accomplished in less than 32 seconds. The Automatic Erase algorithm automatically programs the entire array prior to electrical erase. The timing and verification of electrical erase are P/N:PM1129 REV. 1.1 , JUL. 14, 2005 2 MX29LV320MT/B PIN CONFIGURATION 44 SOP WE# A18 A17 A7 A6 A5 A4 A3 A2 A1 A0 CE# GND OE# Q0 Q8 Q1 Q9 Q2 Q10 Q3 Q11 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 A20 A19 A8 A9 A10 A11 A12 A13 A14 A15 A16 BYTE# GND Q15/A-1 Q7 Q14 Q6 Q13 Q5 Q12 Q4 VCC 48 TSOP A15 A14 A13 A12 A11 A10 A9 A8 A19 A20 WE# RESET# NC WP#/ACC RY/BY# A18 A17 A7 A6 A5 A4 A3 A2 A1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 MX29LV320MT/B P/N:PM1129 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 A16 BYTE# GND Q15/A-1 Q7 Q14 Q6 Q13 Q5 Q12 Q4 VCC Q11 Q3 Q10 Q2 Q9 Q1 Q8 Q0 OE# GND CE# A0 REV. 1.1 , JUL. 14, 2005 3 MX29LV320MT/B 48 Ball CSP (Top View, Ball Down) 8.0 mm 6 A13 A12 A14 A15 A16 BYTE# Q15/ A-1 GND 5 A9 A8 A10 A11 Q7 Q14 Q13 Q6 4 WE# RESET# NC A19 Q5 Q12 VCC Q4 6.0 mm 3 RY/ BY# WP#/ ACC A18 A20 Q2 Q10 Q11 Q3 2 A7 A17 A6 A5 Q0 Q8 Q9 Q1 1 A3 A4 A2 A1 A0 CE# OE# GND A B C D E F G H LOGIC SYMBOL PIN DESCRIPTION SYMBOL PIN NAME A0~A20 Address Input Q0~Q14 Data Inputs/Outputs Q15/A-1 Q15(Word Mode)/LSB addr(Byte Mode) CE# Chip Enable Input WE# Write Enable Input OE# Output Enable Input RESET# Hardware Reset Pin, Active Low 21 A0-A20 CE# OE# WP#/ACC Hardware Write Protect/Programming WE# Acceleration input RY/BY# 16 or 8 Q0-Q15 (A-1) RESET# Read/Busy Output RY/BY# BYTE# Selects 8 bit or 16 bit mode WP#/ACC VCC +3.0V single power supply BYTE# GND Device Ground NC Pin Not Connected Internally P/N:PM1129 REV. 1.1 , JUL. 14, 2005 4 MX29LV320MT/B BLOCK DIAGRAM CE# OE# WE# WP# BYTE# RESET# WRITE CONTROL STATE INPUT LOGIC HIGH VOLTAGE MACHINE (WSM) LATCH BUFFER STATE FLASH REGISTER ARRAY ARRAY Y-DECODER AND X-DECODER ADDRESS A0-A20 PROGRAM/ERASE Y-PASS GATE SOURCE HV COMMAND DATA DECODER SENSE AMPLIFIER PGM DATA HV COMMAND DATA LATCH PROGRAM DATA LATCH Q0-Q15 I/O BUFFER P/N:PM1129 REV. 1.1 , JUL. 14, 2005 5 MX29LV320MT/B BLOCK STRUCTURE MX29LV320MT SECTOR GROUP ARCHITECTURE Sector Group 1 1 1 1 2 2 2 2 3 3 3 3 4 4 4 4 5 5 5 5 6 6 6 6 7 7 7 7 8 8 8 8 9 9 9 9 10 10 Sector Sector Address A20-A12 SA0 000000xxx SA1 000001xxx SA2 000010xxx SA3 000011xxx SA4 000100xxx SA5 000101xxx SA6 000110xxx SA7 000111xxx SA8 001000xxx SA9 001001xxx SA10 001010xxx SA11 001011xxx SA12 001100xxx SA13 001101xxx SA14 001110xxx SA15 001111xxx SA16 010000xxx SA17 010001xxx SA18 010010xxx SA19 010011xxx SA20 010100xxx SA21 010101xxx SA22 010110xxx SA23 010111xxx SA24 011000xxx SA25 011001xxx SA26 011010xxx SA27 011011xxx SA28 011100xxx SA29 011101xxx SA30 011110xxx SA31 011111xxx SA32 100000xxx SA33 100001xxx SA34 100010xxx SA35 100011xxx SA36 100100xxx SA37 100101xxx Sector Size (Kbytes/Kwords) 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 P/N:PM1129 (x8) Address Range 000000h-00FFFFh 010000h-01FFFFh 020000h-02FFFFh 030000h-03FFFFh 040000h-04FFFFh 050000h-05FFFFh 060000h-06FFFFh 070000h-07FFFFh 080000h-08FFFFh 090000h-09FFFFh 0A0000h-0AFFFFh 0B0000h-0BFFFFh 0C0000h-0CFFFFh 0D0000h-0DFFFFh 0E0000h-0EFFFFh 0F0000h-0FFFFFh 100000h-10FFFFh 110000h-11FFFFh 120000h-12FFFFh 130000h-13FFFFh 140000h-14FFFFh 150000h-15FFFFh 160000h-16FFFFh 170000h-17FFFFh 180000h-18FFFFh 190000h-19FFFFh 1A0000h-1AFFFFh 1B0000h-1BFFFFh 1C0000h-1CFFFFh 1D0000h-1DFFFFh 1E0000h-1EFFFFh 1F0000h-1FFFFFh 200000h-20FFFFh 210000h-21FFFFh 220000h-22FFFFh 230000h-23FFFFh 240000h-24FFFFh 250000h-25FFFFh (x16) Address Range 000000h-07FFFh 008000h-0FFFFh 010000h-17FFFh 018000h-01FFFFh 020000h-027FFFh 028000h-02FFFFh 030000h-037FFFh 038000h-03FFFFh 040000h-047FFFh 048000h-04FFFFh 050000h-057FFFh 058000h-05FFFFh 060000h-067FFFh 068000h-06FFFFh 070000h-077FFFh 078000h-07FFFFh 080000h-087FFFh 088000h-08FFFFh 090000h-097FFFh 098000h-09FFFFh 0A0000h-0A7FFFh 0A8000h-0AFFFFh 0B0000h-0B7FFFh 0B8000h-0BFFFFh 0C0000h-0C7FFFh 0C8000h-0CFFFFh 0D0000h-0D7FFFh 0D8000h-0DFFFFh 0E0000h-0E7FFFh 0E8000h-0EFFFFh 0F0000h-0F7FFFh 0F8000h-0FFFFFh 100000h-107FFFh 108000h-10FFFFh 110000h-117FFFh 118000h-11FFFFh 120000h-127FFFh 128000h-12FFFFh REV. 1.1 , JUL. 14, 2005 6 MX29LV320MT/B Sector Group 10 10 11 11 11 11 12 12 12 12 13 13 13 13 14 14 14 14 15 15 15 15 16 16 16 17 18 19 20 21 22 23 24 Sector Sector Address A20-A12 SA38 100110xxx SA39 100111xxx SA40 101000xxx SA41 101001xxx SA42 101010xxx SA43 101011xxx SA44 101100xxx SA45 101101xxx SA46 101110xxx SA47 101111xxx SA48 110000xxx SA49 110001xxx SA50 110010xxx SA51 110011xxx SA52 110100xxx SA53 110101xxx SA54 110110xxx SA55 110111xxx SA56 111000xxx SA57 111001xxx SA58 111010xxx SA59 111011xxx SA60 111100xxx SA61 111101xxx SA62 111110xxx SA63 111111000 SA64 111111001 SA65 111111010 SA66 111111011 SA67 111111100 SA68 111111101 SA69 111111110 SA70 111111111 Sector Size (Kbytes/Kwords) 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 8/4 8/4 8/4 8/4 8/4 8/4 8/4 8/4 (x8) Address Range 260000h-26FFFFh 270000h-27FFFFh 280000h-28FFFFh 290000h-29FFFFh 2A0000h-2AFFFFh 2B0000h-2BFFFFh 2C0000h-2CFFFFh 2D0000h-2DFFFFh 2E0000h-2EFFFFh 2F0000h-2FFFFFh 300000h-30FFFFh 310000h-31FFFFh 320000h-32FFFFh 330000h-33FFFFh 340000h-34FFFFh 350000h-35FFFFh 360000h-36FFFFh 370000h-37FFFFh 380000h-38FFFFh 390000h-39FFFFh 3A0000h-3AFFFFh 3B0000h-3BFFFFh 3C0000h-3CFFFFh 3D0000h-3DFFFFh 3E0000h-3EFFFFh 3F0000h-3F1FFFh 3F2000h-3F3FFFh 3F4000h-3F5FFFh 3F6000h-3F7FFFh 3F8000h-3F9FFFh 3FA000h-3FBFFFh 3FC000h-3FDFFFh 3FE000h-3FFFFFh (x16) Address Range 130000h-137FFFh 138000h-13FFFFh 140000h-147FFFh 148000h-14FFFFh 150000h-157FFFh 158000h-15FFFFh 160000h-147FFFh 168000h-14FFFFh 170000h-177FFFh 178000h-17FFFFh 180000h-187FFFh 188000h-18FFFFh 190000h-197FFFh 198000h-19FFFFh 1A0000h-1A7FFFh 1A8000h-1AFFFFh 1B0000h-1B7FFFh 1B8000h-1BFFFFh 1C0000h-1C7FFFh 1C8000h-1CFFFFh 1D0000h-1D7FFFh 1D8000h-1DFFFFh 1E0000h-1E7FFFh 1E8000h-1EFFFFh 1F0000h-1F7FFFh 1F8000h-1F8FFFh 1F9000h-1F9FFFh 1FA000h-1FAFFFh 1FB000h-1FBFFFh 1FC000h-1FCFFFh 1FD000h-1FDFFFh 1FE000h-1FEFFFh 1FF000h-1FFFFFh Note:The address range is A20:A-1 in byte mode (BYTE#=VIL) or A20:A0 in word mode (BYTE#=VIH) P/N:PM1129 REV. 1.1 , JUL. 14, 2005 7 MX29LV320MT/B MX29LV320MB SECTOR GROUP ARCHITECTURE Sector Group 1 2 3 4 5 6 7 8 9 9 9 10 10 10 10 11 11 11 11 12 12 12 12 13 13 13 13 14 14 14 14 15 15 15 15 16 16 16 16 Sector Sector Address A20-A12 SA0 000000000 SA1 000000001 SA2 000000010 SA3 000000011 SA4 000000100 SA5 000000101 SA6 000000110 SA7 000000111 SA8 000001xxx SA9 000010xxx SA10 000011xxx SA11 000100xxx SA12 000101xxx SA13 000110xxx SA14 000111xxx SA15 001000xxx SA16 001001xxx SA17 001010xxx SA18 001011xxx SA19 001100xxx SA20 001101xxx SA21 001110xxx SA22 001111xxx SA23 010000xxx SA24 010001xxx SA25 010010xxx SA26 010011xxx SA27 010100xxx SA28 010101xxx SA29 010110xxx SA30 010111xxx SA31 011000xxx SA32 011001xxx SA33 011010xxx SA34 011011xxx SA35 011100xxx SA36 011101xxx SA37 011110xxx SA38 011111xxx Sector Size (Kbytes/Kwords) 8/4 8/4 8/4 8/4 8/4 8/4 8/4 8/4 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 P/N:PM1129 (x8) Address Range 000000h-001FFFh 002000h-003FFFh 004000h-005FFFh 006000h-007FFFh 008000h-009FFFh 00A000h-00BFFFh 00C000h-00DFFFh 00E000h-00FFFFh 010000h-01FFFFh 020000h-02FFFFh 030000h-03FFFFh 040000h-04FFFFh 050000h-05FFFFh 060000h-06FFFFh 070000h-07FFFFh 080000h-08FFFFh 090000h-09FFFFh 0A0000h-0AFFFFh 0B0000h-0BFFFFh 0C0000h-0CFFFFh 0D0000h-0DFFFFh 0E0000h-0EFFFFh 0F0000h-0FFFFFh 100000h-10FFFFh 110000h-11FFFFh 120000h-12FFFFh 130000h-13FFFFh 140000h-14FFFFh 150000h-15FFFFh 160000h-16FFFFh 170000h-17FFFFh 180000h-18FFFFh 190000h-19FFFFh 1A0000h-1AFFFFh 1B0000h-1BFFFFh 1C0000h-1CFFFFh 1D0000h-1DFFFFh 1E0000h-1EFFFFh 1F0000h-1FFFFFh (x16) Address Range 000000h-000FFFh 001000h-001FFFh 002000h-002FFFh 003000h-003FFFh 004000h-004FFFh 005000h-005FFFh 006000h-006FFFh 007000h-007FFFh 008000h-00FFFFh 010000h-017FFFh 018000h-01FFFFh 020000h-027FFFh 028000h-02FFFFh 030000h-037FFFh 038000h-03FFFFh 040000h-047FFFh 048000h-04FFFFh 050000h-057FFFh 058000h-05FFFFh 060000h-067FFFh 068000h-06FFFFh 070000h-077FFFh 078000h-07FFFFh 080000h-087FFFh 088000h-08FFFFh 090000h-097FFFh 098000h-09FFFFh 0A0000h-0A7FFFh 0A8000h-0AFFFFh 0B0000h-0B7FFFh 0B8000h-0BFFFFh 0C0000h-0C7FFFh 0C8000h-0CFFFFh 0D0000h-0D7FFFh 0D8000h-0DFFFFh 0E0000h-0E7FFFh 0E8000h-0EFFFFh 0F0000h-0F7FFFh 0F8000h-0FFFFFh REV. 1.1 , JUL. 14, 2005 8 MX29LV320MT/B Sector Group 17 17 17 17 18 18 18 18 19 19 19 19 20 20 20 20 21 21 21 21 22 22 22 22 23 23 23 23 24 24 24 24 Sector Sector Address A20-A12 SA39 100000xxx SA40 100001xxx SA41 100010xxx SA42 100011xxx SA43 100100xxx SA44 100101xxx SA45 100110xxx SA46 100111xxx SA47 101000xxx SA48 101001xxx SA49 101010xxx SA50 101011xxx SA51 101100xxx SA52 101101xxx SA53 101110xxx SA54 101111xxx SA55 110000xxx SA56 110001xxx SA57 110010xxx SA58 110011xxx SA59 110100xxx SA60 110101xxx SA61 110110xxx SA62 110111xxx SA63 111000xxx SA64 111001xxx SA65 111010xxx SA66 111011xxx SA67 111100xxx SA68 111101xxx SA69 111110xxx SA70 111111xxx Sector Size (Kbytes/Kwords) 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 (x8) Address Range 200000h-20FFFFh 210000h-21FFFFh 220000h-22FFFFh 230000h-23FFFFh 240000h-24FFFFh 250000h-25FFFFh 260000h-26FFFFh 270000h-27FFFFh 280000h-28FFFFh 290000h-29FFFFh 2A0000h-2AFFFFh 2B0000h-2BFFFFh 2C0000h-2CFFFFh 2D0000h-2DFFFFh 2E0000h-2EFFFFh 2F0000h-2FFFFFh 300000h-30FFFFh 310000h-31FFFFh 320000h-32FFFFh 330000h-33FFFFh 340000h-34FFFFh 350000h-35FFFFh 360000h-36FFFFh 370000h-37FFFFh 380000h-38FFFFh 390000h-39FFFFh 3A0000h-3AFFFFh 3B0000h-3BFFFFh 3C0000h-3CFFFFh 3D0000h-3DFFFFh 3E0000h-3EFFFFh 3F0000h-3FFFFFh (x16) Address Range 100000h-107FFFh 108000h-10FFFFh 110000h-117FFFh 118000h-11FFFFh 120000h-127FFFh 128000h-12FFFFh 130000h-137FFFh 138000h-13FFFFh 140000h-147FFFh 148000h-14FFFFh 150000h-157FFFh 158000h-15FFFFh 160000h-167FFFh 168000h-16FFFFh 170000h-177FFFh 178000h-17FFFFh 180000h-187FFFh 188000h-18FFFFh 190000h-197FFFh 198000h-19FFFFh 1A0000h-1A7FFFh 1A8000h-1AFFFFh 1B0000h-1B7FFFh 1B8000h-1BFFFFh 1C0000h-1C7FFFh 1C8000h-1CFFFFh 1D0000h-1D7FFFh 1D8000h-1DFFFFh 1E0000h-1E7FFFh 1E8000h-1EFFFFh 1F0000h-1F7FFFh 1F8000h-1FFFFFh Note:The address range is A20:A-1 in byte mode (BYTE#=VIL) or A20:A0 in word mode (BYTE#=VIH) P/N:PM1129 REV. 1.1 , JUL. 14, 2005 9 MX29LV320MT/B Table 1. BUS OPERATION (1) Q8~Q15 Operation CE# OE# WE# RE- WP# ACC Address Q0~Q7 BYTE# SET# Read L L H H X X AIN DOUT BYTE# =VIH =VIL DOUT Q8-Q14= High Z Q15=A-1 Write (Program/Erase) L H L H (Note 3) X AIN (Note 4) (Note 4) Q8-Q14= High Z Q15=A-1 Accelerated Program L H L H (Note 3) V HH AIN (Note 4) (Note 4) Q8-Q14= High Z Q15=A-1 Standby VCC X X 0.3V VCC X H X High-Z High-Z High-Z 0.3V Output Disable L H H H X X X High-Z High-Z High-Z Reset X X X L X X X High-Z High-Z High-Z Sector Group Protect L H L VID H X X X X X (Note 2) Sector Addresses, (Note 4) A6=L,A3=L, A2=L, A1=H,A0=L Chip unprotect L H L VID H X (Note 2) Sector Addresses, (Note 4) A6=H, A3=L, A2=L, A1=H, A0=L Temporary Sector X X X VID H X AIN (Note 4) (Note 4) High-Z Group Unprotect Legend: L=Logic LOW=VIL, H=Logic High=VIH, VID=12.00.5V, VHH=12.00.5V, X=Don't Care, AIN=Address IN, DIN=Data IN, DOUT=Data OUT Notes: 1. Addresses are Amax:A0 in word mode; Amax:A-1 in byte mode. Sector address are Amax:A15 in both modes. 2. The sector group protect and chip unprotect functions may also be implemented via programming equipment. See the "Sector Group Protection and Chip Unprotect" section. 3. If WP#=VIL, the two outermost boot sectors remain protected. If WP#=VIH, the two outermost boot sector protection depends on whether they were last protected or unprotect using the method described in "Sector/ Sector Block Protection and Unprotect". 4. DIN or DOUT as required by command sequence, Data# polling or sector protect algorithm (see Figure 15). P/N:PM1129 REV. 1.1 , JUL. 14, 2005 10 MX29LV320MT/B Table 2. AUTOSELECT CODES (High Voltage Method) A20 A14 Description CE# OE# WE# to to A8 A9 A15 A10 Manufacturer ID L L H X X to A6 A7 VID X L A5 A3 to to A1 A0 BYTE# BYTE# A4 A2 =VIH =VIL X L L L 00 X C2h L L H 22 X 7Eh H H L 22 X 1Ah H H H 22 X 00(bottom boot) Device ID Cycle 1 Cycle 2 L L H X X VID X L X Cycle 3 Q8 to Q15 Q7 to Q0 01h(top boot) Sector Protection L L H SA X VID X L X L H L X X Verification 01h (protected), 00h (unprotected) Secured Silicon Sector Indicator Bit (Q7), WP# 98h L L H X X VID X L X L H H X X (factory locked), protects top two 18h address sector (not factory locked) Secured Silicon Sector 88h Indicator Bit (Q7), WP# protects (factory locked), L L H X X VID X L X L H H X bottom two X 08h address sector (not factory locked) Legend: L = Logic Low = VIL, H = Logic High = VIH, SA = Sector Address, X = Don't care. P/N:PM1129 REV. 1.1 , JUL. 14, 2005 11 MX29LV320MT/B consists of the address bits required to uniquely select a sector. The "Writing specific address and data commands or sequences into the command register initiates device operations. Table 1 defines the valid register command sequences. Writing incorrect address and data values or writing them in the improper sequence resets the device to reading array data. Section has details on erasing a sector or the entire chip, or suspending/resuming the erase operation. REQUIREMENTS FOR READING ARRAY DATA To read array data from the outputs, the system must drive the CE# and OE# pins to VIL. CE# is the power control and selects the device. OE# is the output control and gates array data to the output pins. WE# should remain at VIH. The internal state machine is set for reading array data upon device power-up, or after a hardware reset. This ensures that no spurious alteration of the memory content occurs during the power transition. No command is necessary in this mode to obtain array data. Standard microprocessor read cycles that assert valid address on the device address inputs produce valid data on the device data outputs. The device remains enabled for read access until the command register contents are altered. After the system writes the Automatic Select command sequence, the device enters the Automatic Select mode. The system can then read Automatic Select codes from the internal register (which is separate from the memory array) on Q7-Q0. Standard read cycle timings apply in this mode. Refer to the Automatic Select Mode and Automatic Select Command Sequence section for more information. PAGE MODE READ ICC2 in the DC Characteristics table represents the active current specification for the write mode. The "AC Characteristics" section contains timing specification table and timing diagrams for write operations. The MX29LV320MT/B offers "fast page mode read" function. This mode provides faster read access speed for random locations within a page. The page size of the device is 4 words/8 bytes. The appropriate page is selected by the higher address bits A0~A1(Word Mode)/A1~A1(Byte Mode) This is an asynchronous operation; the microprocessor supplies the specific word location. WRITE BUFFER Write Buffer Programming allows the system to write a maximum of 16 words/32 bytes in one programming operation. This results in faster effective programming time than the standard programming algorithms. See "Write Buffer" for more information. The system performance could be enhanced by initiating 1 normal read and 3 fast page read (for word mode A0A1) or 7 fast page read (for byte mode A-1~A1). When CE# is deasserted and reasserted for a subsequent access, the access time is tACC or tCE. Fast page mode accesses are obtained by keeping the "read-page addresses" constant and changing the "intra-read page" addresses. WRITING COMMANDS/COMMAND QUENCES ACCELERATED PROGRAM OPERATION The device offers accelerated program operations through the ACC function. This is one of two functions provided by the ACC pin. This function is primarily intended to allow faster manufacturing throughput at the factory. SE- If the system asserts VHH on this pin, the device automatically enters the aforementioned Unlock Bypass mode, temporarily unprotects any protected sectors, and uses the higher voltage on the pin to reduce the time required for program operations. The system would use a two-cycle program command sequence as required by the Unlock Bypass mode. Removing VHH from the ACC pin must not be at VHH for operations other than accelerated programming, or device damage may result. To program data to the device or erase sectors of memory, the system must drive WE# and CE# to VIL, and OE# to VIH. An erase operation can erase one sector, multiple sectors, or the entire device. Table indicates the address space that each sector occupies. A "sector address" P/N:PM1129 REV. 1.1 , JUL. 14, 2005 12 MX29LV320MT/B but not within VSS0.3V, the standby current will be greater. STANDBY MODE When using both pins of CE# and RESET#, the device enter CMOS Standby with both pins held at VCC 0.3V. If CE# and RESET# are held at VIH, but not within the range of VCC 0.3V, the device will still be in the standby mode, but the standby current will be larger. During Auto Algorithm operation, VCC active current (ICC2) is required even CE# = "H" until the operation is completed. The device can be read with standard access time (tCE) from either of these standby modes, before it is ready to read data. The RESET# pin may be tied to system reset circuitry. A system reset would that also reset the Flash memory, enabling the system to read the boot-up firmware from the Flash memory. If RESET# is asserted during a program or erase operation, the RY/BY# pin remains a "0" (busy) until the internal reset operation is complete, which requires a time of tREADY (during Embedded Algorithms). The system can thus monitor RY/BY# to determine whether the reset operation is complete. If RESET# is asserted when a program or erase operation is completed within a time of tREADY (not during Embedded Algorithms). The system can read data tRH after the RESET# pin returns to VIH. AUTOMATIC SLEEP MODE The automatic sleep mode minimizes Flash device energy consumption. The device automatically enables this mode when address remain stable for tACC+30ns. The automatic sleep mode is independent of the CE#, WE#, and OE# control signals. Standard address access timings provide new data when addresses are changed. While in sleep mode, output data is latched and always available to the system. ICC4 in the DC Characteristics table represents the automatic sleep mode current specification. Refer to the AC Characteristics tables for RESET# parameters and to Figure 3 for the timing diagram. SECTOR GROUP PROTECT OPERATION The MX29LV320MT/B features hardware sector group protection. This feature will disable both program and erase operations for these sector group protected. In this device, a sector group consists of four adjacent sectors which are protected or unprotected at the same time. To activate this mode, the programming equipment must force VID on address pin A9 and control pin OE#, (suggest VID = 12V) A6 = VIL and CE# = VIL. (see Table 2) Programming of the protection circuitry begins on the falling edge of the WE# pulse and is terminated on the rising edge. Please refer to sector group protect algorithm and waveform. OUTPUT DISABLE With the OE# input at a logic high level (VIH), output from the devices are disabled. This will cause the output pins to be in a high impedance state. RESET# OPERATION MX29LV320MT/B also provides another method. Which requires VID on the RESET# only. This method can be implemented either in-system or via programming equipment. This method uses standard microprocessor bus cycle timing. The RESET# pin provides a hardware method of resetting the device to reading array data. When the RESET# pin is driven low for at least a period of tRP, the device immediately terminates any operation in progress, tristates all output pins, and ignores all read/write commands for the duration of the RESET# pulse. The device also resets the internal state machine to reading array data. The operation that was interrupted should be reinitiated once the device is ready to accept another command sequence, to ensure data integrity To verify programming of the protection circuitry, the programming equipment must force VID on address pin A9 (with CE# and OE# at VIL and WE# at VIH). When A1=1, it will produce a logical "1" code at device output Q0 for a protected sector. Otherwise the device will produce 00H for the unprotected sector. In this mode, the addresses, except for A1, are don't care. Address locations with A1 = VIL are reserved to read manufacturer and device codes. (Read Silicon ID) Current is reduced for the duration of the RESET# pulse. When RESET# is held at VSS0.3V, the device draws CMOS standby current (ICC4). If RESET# is held at VIL P/N:PM1129 REV. 1.1 , JUL. 14, 2005 13 MX29LV320MT/B If the system asserts VIH on the WP# pin, the device reverts to whether the two outermost 8K Byte boot sectors were last set to be protected or unprotect. That is, sector protection or unprotection for these two sectors depends on whether they were last protected or unprotect using the method described in "Sector/Sector Group Protection and Chip Unprotect". It is also possible to determine if the group is protected in the system by writing a Read Silicon ID command. Performing a read operation with A1=VIH, it will produce a logical "1" at Q0 for the protected sector. CHIP UNPROTECT OPERATION Note that the WP# pin must not be left floating or unconnected; inconsistent behavior of the device may result. The MX29LV320MT/B also features the chip unprotect mode, so that all sectors are unprotected after chip unprotect is completed to incorporate any changes in the code. It is recommended to protect all sectors before activating chip unprotect mode. TEMPORARY SECTOR GROUP UNPROTECT OPERATION To activate this mode, the programming equipment must force VID on control pin OE# and address pin A9. The CE# pins must be set at VIL. Pins A6 must be set to VIH. (see Table 2) Refer to chip unprotect algorithm and waveform for the chip unprotect algorithm. The unprotect mechanism begins on the falling edge of the WE# pulse and is terminated on the rising edge. This feature allows temporary unprotect of previously protected sector to change data in-system. The Temporary Sector Unprotect mode is activated by setting the RESET# pin to VID(11.5V-12.5V). During this mode, formerly protected sectors can be programmed or erased as unprotect sector. Once VID is remove from the RESET# pin, all the previously protected sectors are protected again. MX29LV320MT/B also provides another method. Which requires VID on the RESET# only. This method can be implemented either in-system or via programming equipment. This method uses standard microprocessor bus cycle timing. SILICON ID READ OPERATION Flash memories are intended for use in applications where the local CPU alters memory contents. As such, manufacturer and device codes must be accessible while the device resides in the target system. PROM programmers typically access signature codes by raising A9 to a high voltage. However, multiplexing high voltage onto address lines is not generally desired system design practice. It is also possible to determine if the chip is unprotect in the system by writing the Read Silicon ID command. Performing a read operation with A1=VIH, it will produce 00H at data outputs (Q0-Q7) for an unprotect sector. It is noted that all sectors are unprotected after the chip unprotect algorithm is completed. WRITE PROTECT (WP#) MX29LV320MT/B provides hardware method to access the silicon ID read operation. Which method requires VID on A9 pin, VIL on CE#, OE#, A6, and A1 pins. Which apply VIL on A0 pin, the device will output MXIC's manufacture code.. Which apply VIH on A0 pin, the device will output MX29LV320MT/B device code. The write protect function provides a hardware method to protect boot sectors without using VID. If the system asserts VIL on the WP# pin, the device disables program and erase functions in the two "outermost" 8 Kbyte boot sectors independently of whether those sectors were protected or unprotect using the method described in Sector "Sector Group Protection and Chip Unprotect". The two outermost 8 Kbyte boot sectors are the two sectors containing the lowest addresses in a bottom-boot-configured device, or the two sectors containing the highest addresses in a top-boot-configured device. VERIFY SECTOR GROUP PROTECT STATUS OPERATION MX29LV320MT/B provides hardware method for sector group protect status verify. Which method requires VID on A9 pin, VIH on WE# and A1 pins, VIL on CE#, OE#, A6, and A0 pins, and sector address on A16 to A20 pins. P/N:PM1129 REV. 1.1 , JUL. 14, 2005 14 MX29LV320MT/B the system has written the Enter Secured Silicon Sector command sequence, it may read the Secured Silicon Sector by using the address normally occupied by the first sector SA0. Once entry the Secured Silicon Sector the operation of boot sectors is disabled but the operation of main sectors is as normally. This mode of operation continues until the system issues the Exit Secured Silicon Sector command sequence, or until power is removed from the device. On power-up, or following a hardware reset, the device reverts to sending command to sector SA0. Which the identified sector is protected, the device will output 01H. Which the identified sector is not protect, the device will output 00H. DATA PROTECTION The MX29LV320MT/B is designed to offer protection against accidental erasure or programming caused by spurious system level signals that may exist during power transition. During power up the device automatically resets the state machine in the Read mode. In addition, with its control register architecture, alteration of the memory contents only occurs after successful completion of specific command sequences. The device also incorporates several features to prevent inadvertent write cycles resulting from VCC power-up and power-down transition or system noise. Secured Silicon ESN factory Customer Sector address locked lockable range 000000h-000007h ESN Determined by 000008h-00007Fh Unavailable Customer SECURED SILICON SECTOR FACTORY LOCKED:Secured Silicon Sector Programmed and Protected At the Factory The MX29LV320MT/B features a OTP memory region where the system may access through a command sequence to create a permanent part identification as so called Electronic Serial Number (ESN) in the device. Once this region is programmed, any further modification on the region is impossible. The secured silicon sector is a 128 words in length, and uses a Secured Silicon Sector Indicator Bit (Q7) to indicate whether or not the Secured Silicon Sector is locked when shipped from the factory. This bit is permanently set at the factory and cannot be changed, which prevent duplication of a factory locked part. This ensures the security of the ESN once the product is shipped to the field. In device with an ESN, the Secured Silicon Sector is protected when the device is shipped from the factory. The Secured Silicon Sector cannot be modified in any way. A factory locked device has an 8-word random ESN at address 000000h-000007h. CUSTOMER LOCKABLE:Secured Silicon Sector NOT Programmed or Protected At the Factory As an alternative to the factory-locked version, the device may be ordered such that the customer may program and protect the 128-word Secured Silicon Sector. Programming and protecting the Secured Silicon Sector must be used with caution since, once protected, there is no procedure available for unprotected the Secured Silicon Sector area and none of the bits in the Secured Silicon Sector memory space can be modified in any way. The MX29LV320MT/B offers the device with Secured Silicon Sector either factory locked or customer lockable. The factory-locked version is always protected when shipped from the factory , and has the Secured Silicon Sector Indicator Bit permanently set to a "1". The customer-lockable version is shipped with the Secured Silicon Sector unprotected, allowing customers to utilize that sector in any form they prefer. The customer-lockable version has the secured sector Indicator Bit permanently set to a "0". Therefore, the Secured Silicon Sector Indicator Bit prevents customer, lockable device from being used to replace devices that are factory locked. The Secured Silicon Sector area can be protected using one of the following procedures: Write the three-cycle Enter Secured Silicon Sector Region command sequence, and then follow the in-system sector protect algorithm as shown in Figure 15, except that RESET# may be at either VIH or VID. This allows in- The system access the Secured Silicon Sector through a command sequence (refer to "Enter Secured Silicon/ Exit Secured Silicon Sector command Sequence). After P/N:PM1129 REV. 1.1 , JUL. 14, 2005 15 MX29LV320MT/B system protection of the Secured Silicon Sector without raising any device pin to a high voltage. Note that method is only applicable to the Secured Silicon Sector. POWER-UP WRITE INHIBIT If WE#=CE#=VIL and OE#=VIH during power up, the device does not accept commands on the rising edge of WE#. The internal state machine is automatically reset to the read mode on power-up. Write the three-cycle Enter Secured Silicon Sector Region command sequence, and then alternate method of sector protection described in the :Sector Group Protection and Unprotect" section. POWER SUPPLY DE COUPLING Once the Secured Silicon Sector is programmed, locked and verified, the system must write the Exit Secured Silicon Sector Region command sequence to return to reading and writing the remainder of the array. In order to reduce power switching effect, each device should have a 0.1uF ceramic capacitor connected between its VCC and GND. LOW VCC WRITE INHIBIT When VCC is less than VLKO the device does not accept any write cycles. This protects data during VCC power-up and power-down. The command register and all internal program/erase circuits are disabled, and the device resets. Subsequent writes are ignored until VCC is greater than VLKO. The system must provide the proper signals to the control pins to prevent unintentional write when VCC is greater than VLKO. WRITE PULSE "GLITCH" PROTECTION Noise pulses of less than 5ns (typical) on CE# or WE# will not initiate a write cycle. LOGICAL INHIBIT Writing is inhibited by holding any one of OE# = VIL, CE# = VIH or WE# = VIH. To initiate a write cycle CE# and WE# must be a logical zero while OE# is a logical one. POWER-UP SEQUENCE The MX29LV320MT/B powers up in the Read only mode. In addition, the memory contents may only be altered after successful completion of the predefined command sequences. P/N:PM1129 REV. 1.1 , JUL. 14, 2005 16 MX29LV320MT/B Erase Resume (30H) commands are valid only while the Sector Erase operation is in progress. Either of the two reset command sequences will reset the device (when applicable). SOFTWARE COMMAND DEFINITIONS Device operations are selected by writing specific address and data sequences into the command register. Writing incorrect address and data values or writing them in the improper sequence will reset the device to the read mode. Table 3 defines the valid register command sequences. Note that the Erase Suspend (B0H) and All addresses are latched on the falling edge of WE# or CE#, whichever happens later. All data are latched on rising edge of WE# or CE#, whichever happens first. TABLE 3. MX29LV320MT/B COMMAND DEFINITIONS First Bus Command Bus Cycle Second Bus Third Bus Cycle Cycles Addr Data Addr Read (Note 5) 1 RA RD Reset (Note 6) 1 XXX F0 Fourth Bus Cycle Cycle Data Addr Data Addr Data Fifth Bus Sixth Bus Cycle Cycle Addr Data Addr Data Automatic Select (Note 7) Manufacturer ID Device ID Word 4 555 AA 2AA 55 555 90 X00 C2H Byte 4 AAA AA 555 55 AAA 90 X00 C2H Word 4 555 AA 2AA 55 555 X01 227EH X0E 221A X0F 2200/ 90 (Note 8) 2201 Byte 4 AAA AA 555 55 AAA 90 X02 7E Secured Sector Fact- Word 4 555 AA 2AA 55 555 90 X03 see Note 9 ory Protect (Note 9) Byte 4 AAA AA 555 55 AAA 90 X06 Sector Group Protect Word 4 555 AA 2AA 55 555 90 (SA)X02 XX00/ Verify (Note 10) (SA)X04 XX01 Byte 4 AAA AA 555 55 AAA 90 Enter Secured Silicon Word 3 555 AA 2AA 55 555 Sector Byte 3 AAA AA 555 55 AAA 88 Exit Secured Silicon Word 4 555 AA 2AA 55 555 90 XXX 00 Sector Byte 4 AAA AA 555 55 AAA 90 XXX 00 Program Word 4 555 AA 2AA 55 555 PA PD Write to Buffer (Note 11) Program Buffer to Flash X1E 00/01 88 A0 Byte 4 AAA AA 555 55 AAA A0 PA PD Word 6 555 AA 2AA 55 SA 25 SA WC PA PD WBL PD Byte 6 AAA AA 555 55 SA 25 SA BC PA PD WBL PD Word 1 SA 29 2AA 55 555 F0 555 AA 2AA 55 555 10 Byte 1 SA 29 Write to Buffer Abort Word 3 555 AA Reset (Note 12) Byte 3 AAA AA 555 55 AAA F0 Chip Erase Word 6 555 AA 2AA 55 555 Sector Erase X1C 1A 80 Byte 6 AAA AA 555 55 AAA 80 AAA AA 555 55 AAA 10 Word 6 555 AA 2AA 55 555 80 555 AA 2AA 55 SA 30 555 55 AAA 80 AAA AA 555 55 SA 30 Byte 6 AAA AA Program/Erase Suspend (Note 13) 1 XXX B0 Program/Erase Resume (Note 14) 1 XXX 30 CFI Query (Note 15) Word 1 55 98 Byte 1 AA 98 P/N:PM1129 REV. 1.1 , JUL. 14, 2005 17 MX29LV320MT/B Legend: X=Don't care RA=Address of the memory location to be read. RD=Data read from location RA during read operation. PA=Address of the memory location to be programmed. Addresses are latched on the falling edge of the WE# or CE# pulse, whichever happen later. DDI=Data of device identifier C2H for manufacture code PD=Data to be programmed at location PA. Data is latched on the rising edge of WE# or CE# pulse. SA=Address of the sector to be erase or verified (in autoselect mode). Address bits A20-A12 uniquely select any sector. WBL=Write Buffer Location. Address must be within the same write buffer page as PA. WC=Word Count. Number of write buffer locations to load minus 1. BC=Byte Count. Number of write buffer locations to load minus 1. Notes: 1. See Table 1 for descriptions of bus operations. 2. All values are in hexadecimal. 3. Except when reading array or automatic select data, all bus cycles are write operation. 4. Address bits are don't care for unlock and command cycles, except when PA or SA is required. 5. No unlock or command cycles required when device is in read mode. 6. The Reset command is required to return to the read mode when the device is in the automatic select mode or if Q5 goes high. 7. The fourth cycle of the automatic select command sequence is a read cycle. 8. The device ID must be read in three cycles. The data is 01h for top boot and 00h for bottom boot. 9. If WP# protects the top two address sectors, the data is 98h for factory locked and 18h for not factory locked. If WP# protects the bottom two address sectors, the data is 88h for factory locked and 08h for not factor locked. 10. The data is 00h for an unprotected sector/sector block and 01h for a protected sector/sector block. 11. The total number of cycles in the command sequence is determined by the number of words written to the write buffer. The maximum number of cycles in the command sequence is 21(Word Mode) / 37(Byte Mode). 12. Command sequence resets device for next command after aborted write-to-buffer operation. 13. The system may read and program functions in non-erasing sectors, or enter the automatic select mode, when in the erase Suspend mode. The Erase Suspend command is valid only during a sector erase operation. 14. The Erase Resume command is valid only during the Erase Suspend mode. 15. Command is valid when device is ready to read array data or when device is in automatic select mode. P/N:PM1129 REV. 1.1 , JUL. 14, 2005 18 MX29LV320MT/B array data (also applies during Erase Suspend). READING ARRAY DATA The device is automatically set to reading array data after device power-up. No commands are required to retrieve data. The device is also ready to read array data after completing an Automatic Program or Automatic Erase algorithm. SILICON ID READ COMMAND SEQUENCE The SILICON ID READ command sequence allows the host system to access the manufacturer and devices codes, and determine whether or not a sector is protected. Table 2 shows the address and data requirements. This method is an alternative to that shown in Table 1, which is intended for PROM programmers and requires VID on address bit A9. After the device accepts an Erase Suspend command, the device enters the Erase Suspend mode. The system can read array data using the standard read timings, except that if it reads at an address within erasesuspended sectors, the device outputs status data. After completing a programming operation in the Erase Suspend mode, the system may once again read array data with the same exception. See Erase Suspend/Erase Resume Commands for more information on this mode. The system must issue the reset command to re-enable the device for reading array data if Q5 goes high, or while in the automatic select mode. See the "Reset Command" section, next. The SILICON ID READ command sequence is initiated by writing two unlock cycles, followed by the SILICON ID READ command. The device then enters the SILICON ID READ mode, and the system may read at any address any number of times, without initiating another command sequence. A read cycle at address XX00h retrieves the manufacturer code. A read cycle at address XX01h returns the device code. A read cycle containing a sector address (SA) and the address 02h returns 01h if that sector is protected, or 00h if it is unprotected. Refer to Table for valid sector addresses. RESET COMMAND Writing the reset command to the device resets the device to reading array data. Address bits are don't care for this command. The system must write the reset command to exit the automatic select mode and return to reading array data. The reset command may be written between the sequence cycles in an erase command sequence before erasing begins. This resets the device to reading array data. Once erasure begins, however, the device ignores reset commands until the operation is complete. BYTE/WORD PROGRAM COMMAND SEQUENCE The reset command may be written between the sequence cycles in a program command sequence before programming begins. This resets the device to reading array data (also applies to programming in Erase Suspend mode). Once programming begins, however, the device ignores reset commands until the operation is complete. The command sequence requires four bus cycles, and is initiated by writing two unlock write cycles, followed by the program set-up command. The program address and data are written next, which in turn initiate the Embedded Program algorithm. The system is not required to provide further controls or timings. The device automatically generates the program pulses and verifies the programmed cell margin. Table 3 shows the address and data requirements for the byte program command sequence. The reset command may be written between the sequence cycles in an SILICON ID READ command sequence. Once in the SILICON ID READ mode, the reset command must be written to return to reading array data (also applies to SILICON ID READ during Erase Suspend). When the Embedded Program algorithm is complete, the device then returns to reading array data and addresses are no longer latched. The system can determine the status of the program operation by using Q7, Q6, or RY/BY#. See "Write Operation Status" for information on these status bits. If Q5 goes high during a program or erase operation, writing the reset command returns the device to reading Any commands written to the device during the Embedded Program Algorithm are ignored. Note that a hardware P/N:PM1129 REV. 1.1 , JUL. 14, 2005 19 MX29LV320MT/B multiple times, the address/data pair counter will be decremented for every data load operation. The host system must therefore account for loading a write-buffer location more than once. The counter decrements for each data load operation, not for each unique write-buffer-address location. Note also that if an address location is loaded more than once into the buffer, the final data loaded for that address will be programmed. reset immediately terminates the programming operation. The Byte/Word Program command sequence should be reinitiated once the device has reset to reading array data, to ensure data integrity. Programming is allowed in any sequence and across sector boundaries. A bit cannot be programmed from a "0" back to a "1". Attempting to do so may halt the operation and set Q5 to "1", or cause the Data# Polling algorithm to indicate the operation was successful. However, a succeeding read will show that the data is still "0". Only erase operations can convert a "0" to a "1". Once the specified number of write buffer locations have been loaded, the system must then write the Program Buffer to Flash command at the sector address. Any other address and data combination aborts the Write Buffer Programming operation. The device then begins programming. Data polling should be used while monitoring the last address location loaded into the write buffer. Q7, Q6, Q5, and Q1 should be monitored to determine the device status during Write Buffer Programming. Write Buffer Programming Write Buffer Programming allows the system write to a maximum of 16 words/32 bytes in one programming operation. This results in faster effective programming time than the standard programming algorithms. The Write Buffer Programming command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle containing the Write Buffer Load command written at the Sector Address in which programming will occur. The fourth cycle writes the sector address and the number of word locations, minus one, to be programmed. For example, if the system will program 6 unique address locations, then 05h should be written to the device. This tells the device how many write buffer addresses will be loaded with data and therefore when to expect the Program Buffer to Flash command. The number of locations to program cannot exceed the size of the write buffer or the operation will abort. The write-buffer programming operation can be suspended using the standard program suspend/resume commands. Upon successful completion of the Write Buffer Programming operation, the device is ready to execute the next command. The Write Buffer Programming Sequence can be aborted in the following ways: * Load a value that is greater than the page buffer size during the Number of Locations to Program step. * Write to an address in a sector different than the one specified during the Write-Buffer-Load command. * Write an Address/Data pair to a different write-bufferpage than the one selected by the Starting Address during the write buffer data loading stage of the operation. * Write data other than the Confirm Command after the specified number of data load cycles. The fifth cycle writes the first address location and data to be programmed. The write-buffer-page is selected by address bits AMAX-4. All subsequent address/data pairs must fall within the selected-write-buffer-page. The system then writes the remaining address/data pairs into the write buffer. Write buffer locations may be loaded in any order. The abort condition is indicated by Q1 = 1, Q7 = DATA# (for the last address location loaded), Q6 = toggle, and Q5=0. A Write-to-Buffer-Abort Reset command sequence must be written to reset the device for the next operation. Note that the full 3-cycle Write-to-Buffer-Abort Reset command sequence is required when using Write-Buffer-Programming features in Unlock Bypass mode. The write-buffer-page address must be the same for all address/data pairs loaded into the write buffer. (This means Write Buffer Programming cannot be performed across multiple write-buffer pages. This also means that Write Buffer Programming cannot be performed across multiple sectors. If the system attempts to load programming data outside of the selected write-buffer page, the operation will abort. Program Suspend/Program Resume Command Sequence The Program Suspend command allows the system to interrupt a programming operation or a Write to Buffer pro- Note that if a Write Buffer address location is loaded P/N:PM1129 REV. 1.1 , JUL. 14, 2005 20 MX29LV320MT/B gramming operation so that data can be read from any non-suspended sector. When the Program Suspend command is written during a programming process, the device halts the program operation within 15us maximum (5 us typical) and updates the status bits. Addresses are not required when writing the Program Suspend command. MAND The device does not require the system to preprogram prior to erase. The Automatic Erase algorithm automatically pre-program and verifies the entire memory for an all zero data pattern prior to electrical erase. The system is not required to provide any controls or timings during these operations. Table 3 shows the address and data requirements for the chip erase command sequence. After the programming operation has been suspended, the system can read array data from any non-suspended sector. The Program Suspend command may also be issued during a programming operation while an erase is suspended. In this case, data may be read from any addresses not in Erase Suspend or Program Suspend. If a read is needed from the Secured Silicon Sector area (Onetime Program area), then user must use the proper command sequences to enter and exit this region. Any commands written to the chip during the Automatic Erase algorithm are ignored. Note that a hardware reset during the chip erase operation immediately terminates the operation. The Chip Erase command sequence should be reinitiated once the device has returned to reading array data, to ensure data integrity. The system may also write the autoselect command sequence when the device is in the Program Suspend mode. The system can read as many autoselect codes as required. When the device exits the autoselect mode, the device reverts to the Program Suspend mode, and is ready for another valid operation. See Autoselect Command Sequence for more information. The system can determine the status of the erase operation by using Q7, Q6, Q2, or RY/BY#. See "Write Operation Status" for information on these status bits. When the Automatic Erase algorithm is complete, the device returns to reading array data and addresses are no longer latched. Figure 10 illustrates the algorithm for the erase operation. See the Erase/Program Operations tables in "AC Characteristics" for parameters, and to Figure 9 for timing diagrams. After the Program Resume command is written, the device reverts to programming. The system can determine the status of the program operation using the Q7 or Q6 status bits, just as in the standard program operation. See Write Operation Status for more information. SETUP AUTOMATIC CHIP/SECTOR ERASE Chip erase is a six-bus cycle operation. There are two "unlock" write cycles. These are followed by writing the "set-up" command 80H. Two more "unlock" write cycles are then followed by the chip erase command 10H, or the sector erase command 30H. The MX29LV320MT/B contains a Silicon-ID-Read operation to supplement traditional PROM programming methodology. The operation is initiated by writing the read silicon ID command sequence into the command register. Following the command write, a read cycle with A1=VIL,A0=VIL retrieves the manufacturer code of C2H. AUTOMATIC CHIP/SECTOR ERASE COM- P/N:PM1129 REV. 1.1 , JUL. 14, 2005 21 MX29LV320MT/B quires a maximum 20us to suspend the sector erase operation. However, When the Erase Suspend command is written during the sector erase time-out, the device immediately terminates the time-out period and suspends the erase operation. After this command has been executed, the command register will initiate erase suspend mode. The state machine will return to read mode automatically after suspend is ready. At this time, state machine only allows the command register to respond to the Erase Resume, program data to, or read data from any sector not selected for erasure. SECTOR ERASE COMMANDS The Automatic Sector Erase does not require the device to be entirely pre-programmed prior to executing the Automatic Set-up Sector Erase command and Automatic Sector Erase command. Upon executing the Automatic Sector Erase command, the device will automatically program and verify the sector(s) memory for an all-zero data pattern. The system is not required to provide any control or timing during these operations. When the sector(s) is automatically verified to contain an all-zero pattern, a self-timed sector erase and verify begin. The erase and verify operations are complete when the data on Q7 is "1" and the data on Q6 stops toggling for two consecutive read cycles, at which time the device returns to the Read mode. The system is not required to provide any control or timing during these operations. The system can determine the status of the program operation using the Q7 or Q6 status bits, just as in the standard program operation. After an erase-suspend program operation is complete, the system can once again read array data within non-suspended blocks. ERASE RESUME When using the Automatic Sector Erase algorithm, note that the erase automatically terminates when adequate erase margin has been achieved for the memory array (no erase verification command is required). Sector erase is a six-bus cycle operation. There are two "unlock" write cycles. These are followed by writing the set-up command 80H. Two more "unlock" write cycles are then followed by the sector erase command 30H. The sector address is latched on the falling edge of WE# or CE#, whichever happens later , while the command (data) is latched on the rising edge of WE# or CE#, whichever happens first. Sector addresses selected are loaded into internal register on the sixth falling edge of WE# or CE#, whichever happens later. Each successive sector load cycle started by the falling edge of WE# or CE#, whichever happens later must begin within 50us from the rising edge of the preceding WE# or CE#, whichever happens first. Otherwise, the loading period ends and internal auto sector erase cycle starts. (Monitor Q3 to determine if the sector erase timer window is still open, see section Q3, Sector Erase Timer.) Any command other than Sector Erase(30H) or Erase Suspend(B0H) during the time-out period resets the device to read mode. This command will cause the command register to clear the suspend state and return back to Sector Erase mode but only if an Erase Suspend command was previously issued. Erase Resume will not have any effect in all other conditions. Another Erase Suspend command can be written after the chip has resumed erasing. ERASE SUSPEND This command only has meaning while the state machine is executing Automatic Sector Erase operation, and therefore will only be responded during Automatic Sector Erase operation. When the Erase Suspend command is issued during the sector erase operation, the device re- P/N:PM1129 REV. 1.1 , JUL. 14, 2005 22 MX29LV320MT/B The single cycle Query command is valid only when the device is in the Read mode, including Erase Suspend, Standby mode, and Read ID mode; however, it is ignored otherwise. QUERY COMMAND AND COMMON FLASH INTERFACE (CFI) MODE MX29LV320MT/B is capable of operating in the CFI mode. This mode all the host system to determine the manufacturer of the device such as operating parameters and configuration. Two commands are required in CFI mode. Query command of CFI mode is placed first, then the Reset command exits CFI mode. These are described in Table 4. The Reset command exits from the CFI mode to the Read mode, or Erase Suspend mode, or read ID mode. The command is valid only when the device is in the CFI mode. Table 4-1. CFI mode: Identification Data Values (All values in these tables are in hexadecimal) Description Query-unique ASCII string "QRY" Primary vendor command set and control interface ID code Address for primary algorithm extended query table Alternate vendor command set and control interface ID code (none) Address for secondary algorithm extended query table (none) Address h Address h (x16) (x8) 10 20 11 22 12 24 13 26 14 28 15 2A 16 2C 17 2E 18 30 19 32 1A 34 Data h Address h Address h (x16) (x8) 1B 36 1C 38 1D 3A 1E 3C 1F 3E 20 40 21 42 22 44 23 46 24 48 25 4A 26 4C Data h 0051 0052 0059 0002 0000 0040 0000 0000 0000 0000 0000 Table 4-2. CFI Mode: System Interface Data Values Description VCC supply, minimum (2.7V) VCC supply, maximum (3.6V) VPP supply, minimum (none) VPP supply, maximum (none) Typical timeout for single word/byte write (2N us) Typical timeout for maximum size buffer write (2N us) Typical timeout for individual block erase (2N ms) Typical timeout for full chip erase (2N ms) Maximum timeout for single word/byte write times (2N X Typ) Maximum timeout for maximum size buffer write times (2N X Typ) Maximum timeout for individual block erase times (2N X Typ) Maximum timeout for full chip erase times (not supported) P/N:PM1129 0027 0036 0000 0000 0007 0007 000A 0000 0001 0005 0004 0000 REV. 1.1 , JUL. 14, 2005 23 MX29LV320MT/B Table 4-3. CFI Mode: Device Geometry Data Values Description Device size (2n bytes) Flash device interface code (02=asynchronous x8/x16) Maximum number of bytes in multi-byte write = 2n Number of erase block regions Erase block region 1 information [2E,2D] = # of blocks in region -1 [30, 2F] = size in multiples of 256-bytes Erase Block Region 2 Information (refer to CFI publication 100) Erase Block Region 3 Information (refer to CFI publication 100) Erase Block Region 4 Information (refer to CFI publication 100) P/N:PM1129 Address h Address h (x16) (x8) 27 4E 28 50 29 52 2A 54 2B 56 2C 58 2D 5A 2E 5C 2F 5E 30 60 31 62 32 64 33 66 34 68 35 6A 36 6C 37 6E 38 70 39 72 3A 74 3B 76 3C 78 Data h 0016 0002 0000 0005 0000 0002 0007 0000 0020 0000 003E 0000 0000 0001 0000 0000 0000 0000 0000 0000 0000 0000 REV. 1.1 , JUL. 14, 2005 24 MX29LV320MT/B Table 4-4. CFI Mode: Primary Vendor-Specific Extended Query Data Values Description Query-unique ASCII string "PRI" Major version number, ASCII Minor version number, ASCII Address sensitive unlock (0=required, 1= not required) Erase suspend (2= to read and write) Sector protect (N= # of sectors/group) Temporary sector unprotect (1=supported) Sector protect/unprotect scheme Simultaneous R/W operation (0=not supported) Burst mode type (0=not supported) Page mode type (1=4 word page) ACC (Acceleration) Supply Minimum 00h=Not Supported, D7-D4: Volt, D3-D0:100mV ACC (Acceleration) Supply Maximum 00h=Not Supported, D7-D4: Volt, D3-D0:100mV Top/Bottom Boot Sector Flag 02h=Bottom Boot Device, 03h=Top Boot Device Program Suspend 00h=Not Supported, 01h=Supported P/N:PM1129 Address h Address h (x16) (x8) 40 80 41 82 42 84 43 86 44 88 45 8A 46 8C 47 8E 48 90 49 92 4A 94 4B 96 4C 98 4D 9A Data h 0050 0052 0049 0031 0033 0000 0002 0001 0001 0004 0000 0000 0001 00B5 4E 9C 00C5 4F 9E 50 A0 0002/ 0003 0001 REV. 1.1 , JUL. 14, 2005 25 MX29LV320MT/B WRITE OPERATION STATUS method for determining whether a program or erase operation is complete or in progress. These three bits are discussed first. The device provides several bits to determine the status of a write operation: Q2, Q3, Q5, Q6, Q7, and RY/BY#. Table 5 and the following subsections describe the functions of these bits. Q7, RY/BY#, and Q6 each offer a Table 5. Write Operation Status Status Q7 Q6 Q5 Q3 Q2 Q1 RY/BY# Byte/Word Program in Auto Program Algorithm Q7# Toggle 0 N/A No 0 0 Toggle Auto Erase Algorithm Erase Suspend Read Erase (Erase Suspended Sector) Suspended Erase Suspend Read Mode (Non-Erase Suspended Sector) Erase Suspend Program 0 Toggle 0 1 Toggle N/A 0 1 No 0 N/A Toggle N/A 1 Toggle Data Data Data Data Data Data 1 Q7# Toggle 0 N/A N/A N/A 0 Program-Suspended Read Program (Program-Suspended Sector) Suspend Program-Suspended Read Invalid (not allowed) 1 Data 1 (Non-Program-Suspended Sector) Write-to-Buffer Busy Q7# Toggle 0 N/A N/A 0 0 Abort Q7# Toggle 0 N/A N/A 1 0 Notes: 1. Q5 switches to "1" when an Word/Byte Program, Erase, or Write-to-Buffer operation has exceeded the maximum timing limits. Refer to the section on Q5 for more information. 2. Q7 and Q2 require a valid address when reading status information. Refer to the appropriate subsection for further details. 3. The Data# Polling algorithm should be used to monitor the last loaded write-buffer address location. 4. Q1 switches to "1" when the device has aborted the write-to-buffer operation. P/N:PM1129 REV. 1.1 , JUL. 14, 2005 26 MX29LV320MT/B after the rising edge of the final WE# or CE#, whichever happens first pulse in the command sequence (prior to the program or erase operation), and during the sector time-out. Q7: Data# Polling The Data# Polling bit, Q7, indicates to the host system whether an Automatic Algorithm is in progress or completed, or whether the device is in Erase Suspend. Data# Polling is valid after the rising edge of the final WE# pulse in the program or erase command sequence. During an Automatic Program or Erase algorithm operation, successive read cycles to any address cause Q6 to toggle. The system may use either OE# or CE# to control the read cycles. When the operation is complete, Q6 stops toggling. During the Automatic Program algorithm, the device outputs on Q7 the complement of the datum programmed to Q7. This Q7 status also applies to programming during Erase Suspend. When the Automatic Program algorithm is complete, the device outputs the datum programmed to Q7. The system must provide the program address to read valid status information on Q7. If a program address falls within a protected sector, Data# Polling on Q7 is active for approximately 1 us, then the device returns to reading array data. After an erase command sequence is written, if all sectors selected for erasing are protected, Q6 toggles for 100us and returns to reading array data. If not all selected sectors are protected, the Automatic Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. The system can use Q6 and Q2 together to determine whether a sector is actively erasing or is erase suspended. When the device is actively erasing (that is, the Automatic Erase algorithm is in progress), Q6 toggling. When the device enters the Erase Suspend mode, Q6 stops toggling. However, the system must also use Q2 to determine which sectors are erasing or erase-suspended. Alternatively, the system can use Q7. During the Automatic Erase algorithm, Data# Polling produces a "0" on Q7. When the Automatic Erase algorithm is complete, or if the device enters the Erase Suspend mode, Data# Polling produces a "1" on Q7. This is analogous to the complement/true datum output described for the Automatic Program algorithm: the erase function changes all the bits in a sector to "1" prior to this, the device outputs the "complement," or "0". The system must provide an address within any of the sectors selected for erasure to read valid status information on Q7. If a program address falls within a protected sector, Q6 toggles for approximately 2us after the program command sequence is written, then returns to reading array data. After an erase command sequence is written, if all sectors selected for erasing are protected, Data# Polling on Q7 is active for approximately 100 us, then the device returns to reading array data. If not all selected sectors are protected, the Automatic Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. Q6 also toggles during the erase-suspend-program mode, and stops toggling once the Automatic Program algorithm is complete. Table 5 shows the outputs for Toggle Bit I on Q6. Q2:Toggle Bit II When the system detects Q7 has changed from the complement to true data, it can read valid data at Q7-Q0 on the following read cycles. This is because Q7 may change asynchronously with Q0-Q6 while Output Enable (OE#) is asserted low. Q6:Toggle BIT I The "Toggle Bit II" on Q2, when used with Q6, indicates whether a particular sector is actively erasing (that is, the Automatic Erase algorithm is in process), or whether that sector is erase-suspended. Toggle Bit II is valid after the rising edge of the final WE# or CE#, whichever happens first pulse in the command sequence. Toggle Bit I on Q6 indicates whether an Automatic Program or Erase algorithm is in progress or complete, or whether the device has entered the Erase Suspend mode. Toggle Bit I may be read at any address, and is valid Q2 toggles when the system reads at addresses within those sectors that have been selected for erasure. (The system may use either OE# or CE# to control the read cycles.) But Q2 cannot distinguish whether the sector is P/N:PM1129 REV. 1.1 , JUL. 14, 2005 27 MX29LV320MT/B dition. actively erasing or is erase-suspended. Q6, by comparison, indicates whether the device is actively erasing, or is in Erase Suspend, but cannot distinguish which sectors are selected for erasure. Thus, both status bits are required for sectors and mode information. Refer to Table 5 to compare outputs for Q2 and Q6. If this time-out condition occurs during sector erase operation, it specifies that a particular sector is bad and it may not be reused. However, other sectors are still functional and may be used for the program or erase operation. The device must be reset to use other sectors. Write the Reset command sequence to the device, and then execute program or erase command sequence. This allows the system to continue to use the other active sectors in the device. Reading Toggle Bits Q6/ Q2 Whenever the system initially begins reading toggle bit status, it must read Q7-Q0 at least twice in a row to determine whether a toggle bit is toggling. Typically, the system would note and store the value of the toggle bit after the first read. After the second read, the system would compare the new value of the toggle bit with the first. If the toggle bit is not toggling, the device has completed the program or erase operation. The system can read array data on Q7-Q0 on the following read cycle. If this time-out condition occurs during the chip erase operation, it specifies that the entire chip is bad or combination of sectors are bad. If this time-out condition occurs during the byte/word programming operation, it specifies that the entire sector containing that byte is bad and this sector may not be reused, (other sectors are still functional and can be reused). However, if after the initial two read cycles, the system determines that the toggle bit is still toggling, the system also should note whether the value of Q5 is high (see the section on Q5). If it is, the system should then determine again whether the toggle bit is toggling, since the toggle bit may have stopped toggling just as Q5 went high. If the toggle bit is no longer toggling, the device has successfully completed the program or erase operation. If it is still toggling, the device did not complete the operation successfully, and the system must write the reset command to return to reading array data. The time-out condition may also appear if a user tries to program a non blank location without erasing. In this case the device locks out and never completes the Automatic Algorithm operation. Hence, the system never reads a valid data on Q7 bit and Q6 never stops toggling. Once the Device has exceeded timing limits, the Q5 bit will indicate a "1". Please note that this is not a device failure condition since the device was incorrectly used. The Q5 failure condition may appear if the system tries to program a to a "1" location that is previously programmed to "0". Only an erase operation can change a "0" back to a "1". Under this condition, the device halts the operation, and when the operation has exceeded the timing limits, Q5 produces a "1". The remaining scenario is that system initially determines that the toggle bit is toggling and Q5 has not gone high. The system may continue to monitor the toggle bit and Q5 through successive read cycles, determining the status as described in the previous paragraph. Alternatively, it may choose to perform other system tasks. In this case, the system must start at the beginning of the algorithm when it returns to determine the status of the operation. Q3:Sector Erase Timer After the completion of the initial sector erase command sequence, the sector erase time-out will begin. Q3 will remain low until the time-out is complete. Data# Polling and Toggle Bit are valid after the initial sector erase command sequence. Q5:Program/Erase Timing Q5 will indicate if the program or erase time has exceeded the specified limits (internal pulse count). Under these conditions Q5 will produce a "1". This time-out condition indicates that the program or erase cycle was not successfully completed. Data# Polling and Toggle Bit are the only operating functions of the device under this con- If Data# Polling or the Toggle Bit indicates the device has been written with a valid erase command, Q3 may be used to determine if the sector erase timer window is still open. If Q3 is high ("1") the internally controlled erase cycle has begun; attempts to write subsequent commands P/N:PM1129 REV. 1.1 , JUL. 14, 2005 28 MX29LV320MT/B to the device will be ignored until the erase operation is completed as indicated by Data# Polling or Toggle Bit. If Q3 is low ("0"), the device will accept additional sector erase commands. To insure the command has been accepted, the system software should check the status of Q3 prior to and following each subsequent sector erase command. If Q3 were high on the second status check, the command may not have been accepted. If the time between additional erase commands from the system can be less than 50us, the system need not to monitor Q3. Q1: Write-to-Buffer Abort Q1 indicates whether a Write-to-Buffer operation was aborted. Under these conditions Q1 produces a "1". The system must issue the Write-to-Buffer-Abort-Reset command sequence to return the device to reading array data. See Write Buffer section for more details. RY/BY#:READY/BUSY OUTPUT The RY/BY# is a dedicated, open-drain output pin that indicates whether an Embedded Algorithm is in progress or complete. The RY/BY# status is valid after the rising edge of the final WE# pulse in the command sequence. Since RY/BY# is an open-drain output, several RY/BY# pins can be tied together in parallel with a pull-up resistor to VCC . If the output is low (Busy), the device is actively erasing or programming. (This includes programming in the Erase Suspend mode.) If the output is high (Ready), the device is ready to read array data (including during the Erase Suspend mode), or is in the standby mode. P/N:PM1129 REV. 1.1 , JUL. 14, 2005 29 MX29LV320MT/B ABSOLUTE MAXIMUM RATINGS OPERATING RATINGS Storage Temperature Plastic Packages . . . . . . . . . . . . . ..... -65oC to +150oC Ambient Temperature with Power Applied. . . . . . . . . . . . . .... -65oC to +125oC Voltage with Respect to Ground VCC (Note 1) . . . . . . . . . . . . . . . . . -0.5 V to +4.0 V A9, OE#, and RESET# (Note 2) . . . . . . . . . . . ....-0.5 V to +12.5 V All other pins (Note 1) . . . . . . . -0.5 V to VCC +0.5 V Output Short Circuit Current (Note 3) . . . . . . 200 mA Commercial (C) Devices Ambient Temperature (TA ). . . . . . . . . . . . . 0 C to +70 C Industrial (I) Devices Ambient Temperature (TA ). . . . . . . . . . . -40 C to +85 C VCC Supply Voltages VCC for full voltage range. . . . . .. . . . . . +2.7 V to 3.6 V VCC for regulated voltage range. . . . . . . +3.0 V to 3.6 V Operating ranges define those limits between which the functionality of the device is guaranteed. Notes: 1. Minimum DC voltage on input or I/O pins is -0.5 V. During voltage transitions, input or I/O pins may overshoot VSS to -2.0 V for periods of up to 20 ns. Maximum DC voltage on input or I/O pins is VCC +0.5 V. During voltage transitions, input or I/O pins may overshoot to VCC +2.0 V for periods up to 20ns. 2. Minimum DC input voltage on pins A9, OE#, and RESET# is -0.5 V. During voltage transitions, A9, OE#, and RESET# may overshoot VSS to -2.0 V for periods of up to 20 ns. Maximum DC input voltage on pin A9 is +12.5 V which may overshoot to 14.0 V for periods up to 20 ns. 3. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second. Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this data sheet is not implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability. P/N:PM1129 REV. 1.1 , JUL. 14, 2005 30 MX29LV320MT/B DC CHARACTERISTICS TA=-40 C to 85 C, VCC=2.7V~3.6V (TA= 0 C to 70 C, VCC=3.0V~3.6V for 70R) Parameter Description I LI Input Load Current (Note 1) I LIT I LO A9 Input Leakage Current Output Leakage Current ICC1 VCC Initial Read Current (Notes 2,3) ICC2 VCC Intra-Page Read Current (Notes 2,3) ICC3 VCC Active Write Current (Notes 2,4,6) ICC4 VCC Standby Current (Note 2) ICC5 VCC Reset Current (Note 2) ICC6 Automatic Sleep Mode (Note 2,5) VIL VIH VHH Input Low Voltage Input High Voltage Voltage for ACC Program Acceleration VID Voltage for Autoselect and Temporary Sector Unprotect VOL Output Low Voltage VOH1 Output High Voltage VOH2 VLKO Low VCC Lock-Out Voltage (Note 4) Test Conditions VIN = VSS to VCC , VCC = VCC max VCC=VCC max; A9 = 12.5V VOUT = VSS to VCC , VCC= VCC max CE#= VIL, 10 MHz OE# = VIH 5 MHz 1 MHz Min. Max. 1.0 Unit uA 35 1.0 uA uA 35 18 5 50 25 20 mA mA mA 5 10 50 20 40 60 mA mA mA 20 50 uA 20 50 uA 20 50 uA VCC = 2.7V ~ 3.6V -0.5 0.7xVCC 11.5 12.0 0.8 VCC+0.5 12.5 V V V VCC = 3.0 V 10% 11.5 12.0 12.5 V 0.45 V V V V CE#= VIL , 10 MHz OE# = VIH 40 MHz CE#= VIL , OE# = VIH WE#=VIL CE#,RESET#=VCC0.3V WP#=VIH RESET#=VSS0.3V WP#=VIH VIL = V SS 0.3 V, VIH = VCC 0.3 V, WP#=VIH IOL= 4.0mA,VCC=VCC min IOH=-2.0mA,VCC=VCC min 0.85xVCC IOH=-100uA,VCC=VCC min VCC-0.4 2.3 Typ. 2.5 Notes: 1. On the WP#/ACC pin only, the maximum input load current when WP# = VIL is 5.0uA. 2. Maximum ICC specifications are tested with VCC = VCC max. 3. The ICC current listed is typically is less than 2 mA/MHz, with OE# at VIH. Typical specifications are for VCC = 3.0V. 4. ICC active while Embedded Erase or Embedded Program is in progress. 5. Automatic sleep mode enables the low power mode when addresses remain stable for tACC + 30 ns. 6. Not 100% tested. 7. A9=12.5V when TA=0 C to 85 C, A9=12V when when TA=-40 C to 0 C. P/N:PM1129 REV. 1.1 , JUL. 14, 2005 31 MX29LV320MT/B TEST SPECIFICATIONS SWITCHING TEST CIRCUITS Test Condition Output Load Output Load Capacitance, CL (including jig capacitance) Input Rise and Fall Times Input Pulse Levels Input timing measurement reference levels Output timing measurement reference levels 2.7K ohm DEVICE UNDER TEST 3.3V CL 6.2K ohm DIODES=IN3064 OR EQUIVALENT All Speeds 1 TTL gate 30 Unit 5 0.0-3.0 1.5 ns V V 1.5 V pF KEY TO SWITCHING WAVEFORMS WAVEFORM INPUTS OUTPUTS Steady Changing from H to L Changing from L to H Don't Care, Any Change Permitted Changing, State Unknown Does Not Apply Center Line is High Impedance State(High Z) SWITCHING TEST WAVEFORMS 3.0V 1.5 Measurement Level 1.5 0.0V INPUT OUTPUT P/N:PM1129 REV. 1.1 , JUL. 14, 2005 32 MX29LV320MT/B Read-Only Operations AC CHARACTERISTICS TA=-40 C to 85 C, VCC=2.7V~3.6V (TA= 0 C to 70 C, VCC=3.0V~3.6V for 70R) Parameter Speed Options Std. Description Test Setup 70R 90 Unit tRC Read Cycle Time (Note 1) Min 70 90 ns tACC Address to Output Delay CE#, OE#=VIL Max 70 90 ns tCE Chip Enable to Output Delay OE#=VIL Max 70 90 ns tPACC Page Access Time Max 25 25 ns tOE Output Enable to Output Delay Max 35 35 ns tDF Chip Enable to Output High Z (Note 1) Max 16 ns tDF Output Enable to Output High Z (Note 1) Max 16 ns tOH Output Hold Time From Address, CE# Min 0 ns Read Min 35 ns Output Enable Hold Time Toggle and Min 10 ns (Note 1) Data# Polling or OE#, whichever Occurs First tOEH Notes: 1. Not 100% tested. 2. See SWITCHING TEST CIRCUITS and TEST SPECIFICATIONS TABLE for test specifications. P/N:PM1129 REV. 1.1 , JUL. 14, 2005 33 MX29LV320MT/B Figure 1. READ TIMING WAVEFORMS tRC VIH ADD Valid Addresses VIL tCE VIH CE# tRH VIL tRH VIH WE# VIL OE# VIH VIL Outputs tDF tOE tOEH VOH tOH tACC HIGH Z HIGH Z DATA Valid VOL VIH RESET# VIL RY/BY# 0V Figure 2. PAGE READ TIMING WAVEFORMS Same Page A2-A20 (A-1), A0~A2 tACC CE# tPACC Output tPACC tPACC OE# Qa Qb P/N:PM1129 Qc Qd REV. 1.1 , JUL. 14, 2005 34 MX29LV320MT/B RESET# Operations AC CHARACTERISTICS Parameter Description Test Setup All Speed Options Unit tREADY1 RESET# PIN Low (During Automatic Algorithms) MAX 20 us MAX 500 ns to Read or Write (See Note) tREADY2 RESET# PIN Low (NOT During Automatic Algorithms) to Read or Write (See Note) tRP RESET# Pulse Width (NOT During Automatic Algorithms) MIN 500 ns tRH RESET# High Time Before Read (See Note) MIN 50 ns tRB RY/BY# Recovery Time(to CE#, OE# go low) MIN 0 ns tRPD RESET# Low to Standby Mode MIN 20 us Note:Not 100% tested Figure 3. RESET# TIMING WAVEFORM RY/BY# CE#, OE# tRH RESET# tRP tReady2 Reset Timing NOT during Automatic Algorithms tReady1 RY/BY# tRB CE#, OE# RESET# tRP Reset Timing during Automatic Algorithms P/N:PM1129 REV. 1.1 , JUL. 14, 2005 35 MX29LV320MT/B Erase and Program Operations AC CHARACTERISTICS TA=-40 C to 85 C, VCC=2.7V~3.6V (TA= 0 C to 70 C, VCC=3.0V~3.6V for 70R) Parameter Std. tWC tAS tASO tAH tAHT tDS tDH tCEPH tOEPH tGHWL tGHEL tCS tCH tWP tWPH tWHWH1 tWHWH2 tVCS tRB tBUSY tVHH tPOLL Description Write Cycle Time (Note 1) Address Setup Time Address Setup Time to OE# low during toggle bit polling Address Hold Time Address Hold Time From CE# or OE# high during toggle bit polling Data Setup Time Data Hold Time CE# High During Toggle Bit Polling Output Enable High during toggle bit polling Read Recovery Time Before Write (OE# High to WE# Low) Read Recovery Time Before Write CE# Setup Time CE# Hold Time Write Pulse Width Write Pulse Width High Write Buffer Program Operation (Notes 2,3) Single Word/Byte Program Operation (Notes 2,5) Accelerated Single Word/Byte Programming Operation (Notes 2,5) Sector Erase Operation (Note 2) VCC Setup Time (Note 1) Write Recovery Time from RY/BY# Program/Erase Valid to RY/BY# Delay VHH Rise and Fall Time (Note 1) Program Valid Before Status Polling (Note 6) Byte Word Byte Word Min Min Min Min Min Speed Options 70R 90 70 90 0 15 45 0 Unit ns ns ns ns ns Min Min Min Min Min 35 0 20 20 0 ns ns ns ns ns Min Min Min Min Min Typ Typ Typ Typ Typ Typ Min Min Min Min Max 0 0 0 35 30 240 60 60 54 54 0.5 50 0 ns ns ns ns ns us us us us us sec us ns ns ns us 70 90 250 4 Notes: 1. Not 100% tested. 2. See the "Erase And Programming Performance" section for more information. 3. For 1-16 words/1-32 bytes programmed. 4. Effective write buffer specification is based upon a 16-word/32-byte write buffer operation. 5. Word/Byte programming specification is based upon a single word/byte programming operation not utilizing the write buffer. 6. When using the program suspend/resume feature, if the suspend command is issued within tPOLL, tPOLL must be fully re-applied upon resuming the programming operation. If the suspend command is issued after tPOLL, tPOLL is not required again prior to reading the status bits upon resuming. P/N:PM1129 REV. 1.1 , JUL. 14, 2005 36 MX29LV320MT/B Figure 4. AUTOMATIC PROGRAM TIMING WAVEFORMS Program Command Sequence(last two cycle) tWC XXXh Address Read Status Data (last two cycle) tAS PA PA PA tAH CE# tCH OE# tPOLL tWP WE# tWHWH1 tCS tWPH tDS tDH A0h Status PD DOUT Data tBUSY tRB RY/BY# tVCS VCC Note : 1.PA=Program Address, PD=Program Data, DOUT is the true data the program address Figure 5. ACCELERATED PROGRAM TIMING DIAGRAM VHH ACC VIL or VIH VIL or VIH tVHH tVHH P/N:PM1129 REV. 1.1 , JUL. 14, 2005 37 MX29LV320MT/B Figure 6. AUTOMATIC PROGRAMMING ALGORITHM FLOWCHART START Write Data AAH Address 555H Write Data 55H Address 2AAH Write Data A0H Address 555H Write Program Data/Address Data Poll from system Increment Address No Verify Word Ok ? YES No Last Address ? YES Auto Program Completed P/N:PM1129 REV. 1.1 , JUL. 14, 2005 38 MX29LV320MT/B Figure 7. WRITE BUFFER PROGRAMMING ALGORITHM FLOWCHART Write "Write to Buffer" command and Sector Address Write number of addresses to program minus 1(WC) and Sector Address Part of "Write to Buffer" Command Sequence Write first address/data Yes WC = 0 ? No Abort Write to Buffer Operation ? Yes Write to a different sector address No Write to buffer ABORTED. Must write "Write-to-buffer Abort Reset" command sequence to return to read mode. Write next address/data pair (Note 1) WC = WC - 1 Write program buffer to flash sector address Notes: 1. When Sector Address is specified, any address in the selected sector is acceptable. However, when loading Write-Buffer address locations with data, all addresses must fall within the selected Write-Buffer Page. 2. Q7 may change simultaneously with Q5. Therefore, Q7 should be verified. 3. If this flowchart location was reached because Q5= "1" then the device FAILED. If this flowchart location was reached because Q1="1", then the Write to Buffer operation was ABORTED. In either case, the proper reset command must be written before the device can begin another operation. If Q1=1, write the Write-Buffer-Programming-Abort-Reset command. If Q5=1, write the Reset command. 4. See Table 3 for command sequences required for write buffer programming. Read Q7~Q0 at Last Loaded Address Yes Q7 = Data ? No No No Q5 = 1 ? Q1 = 1 ? Yes Yes Read Q7~Q0 with address = Last Loaded Address (Note 2) Q7 and Q15 = Data ? Yes No (Note 3) FAIL or ABORT PASS P/N:PM1129 REV. 1.1 , JUL. 14, 2005 39 MX29LV320MT/B Figure 8. PROGRAM SUSPEND/RESUME FLOWCHART Program Operation or Write-to-Buffer Sequence in Progress Write address/data XXXh/B0h Write Program Suspend Command Sequence Command is also valid for Erase-suspended-program operations Wait 15us Autoselect and Secured Sector read operations are also allowed Data cannot be read from erase-or program-suspended sectors Read data as required No Done reading ? Yes Write address/data XXXh/30h Write Program Resume Command Sequence Device reverts to operation prior to Program Suspend P/N:PM1129 REV. 1.1 , JUL. 14, 2005 40 MX29LV320MT/B Figure 9. AUTOMATIC CHIP/SECTOR ERASE TIMING WAVEFORM Erase Command Sequence(last two cycle) tWC 2AAh Address Read Status Data tAS VA SA 555h for chip erase VA tAH CE# tCH OE# tWHWH2 tWP WE# tCS tWPH tDS tDH 55h Data In Progress Complete 30h 10 for Chip Erase tBUSY tRB RY/BY# tVCS VCC Note : 1.SA=sector address(for Sector Erase), VA=Valid Address for reading status data(see "Write Operation Status"). P/N:PM1129 REV. 1.1 , JUL. 14, 2005 41 MX29LV320MT/B Figure 10. AUTOMATIC CHIP ERASE ALGORITHM FLOWCHART START Write Data AAH Address 555H Write Data 55H Address 2AAH Write Data 80H Address 555H Write Data AAH Address 555H Write Data 55H Address 2AAH Write Data 10H Address 555H Data Poll from system YES No DATA = FFh ? YES Auto Erase Completed P/N:PM1129 REV. 1.1 , JUL. 14, 2005 42 MX29LV320MT/B Figure 11. AUTOMATIC SECTOR ERASE ALGORITHM FLOWCHART START Write Data AAH Address 555H Write Data 55H Address 2AAH Write Data 80H Address 555H Write Data AAH Address 555H Write Data 55H Address 2AAH Write Data 30H Sector Address NO Last Sector to Erase ? YES Data Poll from System NO Data=FFh? YES Auto Sector Erase Completed P/N:PM1129 REV. 1.1 , JUL. 14, 2005 43 MX29LV320MT/B Figure 12. ERASE SUSPEND/RESUME FLOWCHART START Write Data B0H NO ERASE SUSPEND Toggle Bit checking Q6 not toggled YES Read Array or Program Reading or Programming End NO YES Write Data 30H ERASE RESUME Continue Erase Another Erase Suspend ? NO YES P/N:PM1129 REV. 1.1 , JUL. 14, 2005 44 MX29LV320MT/B AC CHARACTERISTICS Alternate CE# Controlled Erase and Program Operations TA=-40 C to 85 C, VCC=2.7V~3.6V (TA= 0 C to 70 C, VCC=3.0V~3.6V for 70R) Parameter Speed Options Std. Description 70R 90 Unit tWC Write Cycle Time (Note 1) Min 70 90 ns tAS Address Setup Time Min 0 ns tAH Address Hold Time Min 45 ns tDS Data Setup Time Min 35 ns tDH Data Hold Time Min 0 ns tGHEL Read Recovery Time Before Write Min 0 ns (OE# High to WE# Low) tWS WE# Setup Time Min 0 ns tWH WE# Hold Time Min 0 ns tCP CE# Pulse Width Min 35 ns tCPH CE# Pulse Width High Min 25 ns Write Buffer Program Operation (Notes 2,3) Typ 240 us tWHWH1 Single Word/Byte Program Byte Typ 60 us Operation (Notes 2,5) Word Typ 60 us Accelerated Single Word/Byte Byte Typ 54 us Programming Operation (Notes 2,5) Word Typ 54 us tWHWH2 Sector Erase Operation (Note 2) Typ 0.5 sec tRH RESET HIGH Time Before Write (Note 1) Min 50 ns Notes: 1. Not 100% tested. 2. See the "Erase And Programming Performance" section for more information. 3. For 1-16 words/1-32 bytes programmed. 4. Effective write buffer specification is based upon a 16-word/32-byte write buffer operation. 5. Word/Byte programming specification is based upon a single word/byte programming operation not utilizing the write buffer. 6. When using the program suspend/resume feature, if the suspend command is issued within tPOLL, tPOLL must be fully re-applied upon resuming the programming operation. If the suspend command is issued after tPOLL, tPOLL is not required again prior to reading the status bits upon resuming. P/N:PM1129 REV. 1.1 , JUL. 14, 2005 45 MX29LV320MT/B Figure 13. CE# CONTROLLED PROGRAM TIMING WAVEFORM 555 for program 2AA for erase PA for program SA for sector erase 555 for chip erase Data# Polling Address PA tWC tAS tAH tWH WE# tGHEL OE# tCP tWHWH1 or 2 CE# tWS tCPH tDS tBUSY tDH Q7 Data tRH A0 for program 55 for erase DOUT PD for program 30 for sector erase 10 for chip erase RESET# RY/BY# NOTES: 1.PA=Program Address, PD=Program Data, DOUT=Data Out, Q7=complement of data written to device. 2.Figure indicates the last two bus cycles of the command sequence. P/N:PM1129 REV. 1.1 , JUL. 14, 2005 46 MX29LV320MT/B SECTOR GROUP PROTECT/CHIP UNPROTECT Figure 14. Sector Group Protect / Chip Unprotect Waveform (RESET# Control) VID VIH RESET# SA, A6 A1, A0 Valid* Valid* Sector Group Protect or Chip Unprotect Data 60h 1us 60h Valid* Verify 40h Status Sector Group Protect:150us Chip Unprotect:15ms CE# WE# OE# Note: For sector group protect A6=0, A1=1, A0=0. For chip unprotect A6=1, A1=1, A0=0 P/N:PM1129 REV. 1.1 , JUL. 14, 2005 47 MX29LV320MT/B Figure 15. IN-SYSTEM SECTOR GROUP PROTECT/CHIP UNPROTECT ALGORITHMS WITH RESET#=VID START START Protect all sectors: The indicated portion of the sector protect algorithm must be performed for all unprotected sectors prior to issuing the first sector unprotect address PLSCNT=1 RESET#=VID Wait 1us PLSCNT=1 RESET#=VID Wait 1us Temporary Sector Unprotect Mode No First Write Cycle=60h? First Write Cycle=60h? No Temporary Sector Unprotect Mode Yes Yes Set up sector address No Sector Protect: Write 60h to sector address with A6=0, A1=1, A0=0 All sectors protected? Yes Set up first sector address Wait 150us Verify Sector Protect: Write 40h to sector address with A6=0, A1=1, A0=0 Sector Unprotect: Write 60h to sector address with A6=1, A1=1, A0=0 Reset PLSCNT=1 Increment PLSCNT Wait 15 ms Read from sector address with A6=0, A1=1, A0=0 Verify Sector Unprotect: Write 40h to sector address with A6=1, A1=1, A0=0 No Increment PLSCNT No PLSCNT=25? Yes Data=01h? Read from sector address with A6=1, A1=1, A0=0 Yes No Device failed Protect another No sector? Sector Protect Algorithm Reset PLSCNT=1 Yes PLSCNT=1000? Data=00h? No Yes Remove VID from RESET# Yes Device failed Last sector verified? Write reset command Chip Unprotect Algorithm Sector Protect complete No Yes Remove VID from RESET# Write reset command Sector Unprotect complete P/N:PM1129 REV. 1.1 , JUL. 14, 2005 48 MX29LV320MT/B AC CHARACTERISTICS Parameter Description Test Setup All Speed Options Unit tVLHT Voltage transition time Min. 4 us tWPP1 Write pulse width for sector group protect Min. 100 ns tWPP2 Write pulse width for chip unprotect Min. 100 ns tOESP OE# setup time to WE# active Min. 4 us Figure 16. SECTOR GROUP PROTECT TIMING WAVEFORM (A9, OE# Control) A1 A6 12V 3V A9 tVLHT Verify 12V 3V OE# tVLHT tVLHT tWPP 1 WE# tOESP CE# Data 01H F0H tOE A20-A16 Sector Address P/N:PM1129 REV. 1.1 , JUL. 14, 2005 49 MX29LV320MT/B Figure 17. SECTOR GROUP PROTECTION ALGORITHM (A9, OE# Control) START Set Up Sector Addr PLSCNT=1 OE#=VID, A9=VID, CE#=VIL A6=VIL Activate WE# Pulse Time Out 150us Set WE#=VIH, CE#=OE#=VIL A9 should remain VID Read from Sector Addr=SA, A1=1 No PLSCNT=32? . No Data=01H? Yes Device Failed Protect Another Sector? Yes Remove VID from A9 Write Reset Command Sector Protection Complete P/N:PM1129 REV. 1.1 , JUL. 14, 2005 50 MX29LV320MT/B Figure 18. CHIP UNPROTECT TIMING WAVEFORM (A9, OE# Control) A1 12V 3V A9 tVLHT A6 Verify 12V 3V OE# tVLHT tVLHT tWPP 2 WE# tOESP CE# Data 00H F0H tOE P/N:PM1129 REV. 1.1 , JUL. 14, 2005 51 MX29LV320MT/B Figure 19. CHIP UNPROTECT FLOWCHART (A9, OE# Control) START Protect All Sectors PLSCNT=1 Set OE#=A9=VID CE#=VIL, A6=1 Activate WE# Pulse Time Out 15ms Increment PLSCNT Set OE#=CE#=VIL A9=VID, A1=1 Set Up First Sector Addr Read Data from Device No Data=00H? Increment Sector Addr Yes No All sectors have No PLSCNT=1000? Yes Device Failed been verified? Yes Remove VID from A9 Write Reset Command Chip Unprotect Complete * It is recommended before unprotect whole chip, all sectors should be protected in advance. P/N:PM1129 REV. 1.1 , JUL. 14, 2005 52 MX29LV320MT/B AC CHARACTERISTICS Parameter Description Test All Speed Options Unit Setup tVIDR VID Rise and Fall Time (see Note) Min 500 ns tRSP RESET# Setup Time for Temporary Sector Unprotect Min 4 us tRRB RESET# Hold Time from RY/BY# High for Temporary Min 4 us Sector Group Unprotect Figure 20. TEMPORARY SECTOR GROUP UNPROTECT WAVEFORMS 12V RESET# 0 or 3V VIL or VIH tVIDR tVIDR Program or Erase Command Sequence CE# WE# tRSP tRRB RY/BY# P/N:PM1129 REV. 1.1 , JUL. 14, 2005 53 MX29LV320MT/B Figure 21. TEMPORARY SECTOR GROUP UNPROTECT FLOWCHART Start RESET# = VID (Note 1) Perform Erase or Program Operation Operation Completed RESET# = VIH Temporary Sector Unprotect Completed(Note 2) Notes : 1. All protected sectors are temporary unprotected. VID=11.5V~12.5V 2. All previously protected sectors are protected again. P/N:PM1129 REV. 1.1 , JUL. 14, 2005 54 MX29LV320MT/B Figure 22. SECURED SILICON SECTOR PROTECTED ALGORITHMS FLOWCHART START Enter Secured Silicon Sector Wait 1us First Wait Cycle Data=60h Second Wait Cycle Data=60h A6=0, A1=1, A0=0 Wait 300us No Data = 01h ? Yes Device Failed Write Reset Command Secured Sector Protect Complete P/N:PM1129 REV. 1.1 , JUL. 14, 2005 55 MX29LV320MT/B Figure 23. SILICON ID READ TIMING WAVEFORM VCC 3V VID VIH VIL ADD A9 ADD A0 VIH VIL tACC A1 tACC tACC tACC VIH VIL A2 VIH VIL ADD VIH VIL CE# VIH VIL tCE WE# VIH VIL OE# VIH tOE tDF VIL tOH tOH tOH tOH VIH DATA Q0-Q15 VIL DATA OUT DATA OUT DATA OUT DATA OUT Manufacturer ID Device ID Cycle 1 Device ID Cycle 2 Device ID Cycle 3 P/N:PM1129 REV. 1.1 , JUL. 14, 2005 56 MX29LV320MT/B WRITE OPERATION STATUS Figure 24. DATA# POLLING TIMING WAVEFORMS (DURING AUTOMATIC ALGORITHMS) tRC Address VA VA VA tACC tCE CE# tCH tOE OE# tOEH tDF WE# tOH Q7 Status Data Q0-Q6 Status Data Complement Status Data True True Valid Data Valid Data High Z High Z tBUSY RY/BY# Note : VA=Valid address. Figure shows are first status cycle after command sequence, last status read cycle, and array data raed cycle. P/N:PM1129 REV. 1.1 , JUL. 14, 2005 57 MX29LV320MT/B Figure 25. DATA# POLLING ALGORITHM Start Read Q7~Q0 Add.=VA(1) Yes Q7 = Data ? No No Q5 = 1 ? Yes Read Q7~Q0 Add.=VA Yes Q7 = Data ? (2) No FAIL Pass Notes: 1.VA=valid address for programming. 2.Q7 should be rechecked even Q5="1" because Q7 may change simultaneously with Q5. P/N:PM1129 REV. 1.1 , JUL. 14, 2005 58 MX29LV320MT/B Figure 26. TOGGLE BIT TIMING WAVEFORMS (DURING AUTOMATIC ALGORITHMS) tRC Address tAS VA VA VA VA tAHT tACC tCE CE# tCEPH tCH tASO tOE tOEPH OE# tOEH tDF WE# tDH Q6/Q2 Valid Status tOH Valid Status (first read) Valid Status Valid Data (second read) (stops toggling) Valid Data RY/BY# Note : VA=Valid address; not required for Q6. Figure shows first two status cycle after command sequence, last status read cycle, and array data read cycle. P/N:PM1129 REV. 1.1 , JUL. 14, 2005 59 MX29LV320MT/B Figure 27. TOGGLE BIT ALGORITHM START Read Q7~Q0 Read Q7~Q0 (Note 1) NO Toggle Bit Q6 =Toggle? YES NO Q5=1? YES Read Q7~Q0 Twice (Note 1,2) Toggle Bit Q6= Toggle? YES Program/Erase Operation Not Complete, Write Reset Command Program/Erase Operation Complete Notes : 1. Read toggle bit twice to determine whether or not it is toggling. 2. Recheck toggle bit because it may stop toggling as Q5 changes to "1". P/N:PM1129 REV. 1.1 , JUL. 14, 2005 60 MX29LV320MT/B Figure 28. Q6 versus Q2 Enter Embedded Erasing Erase Suspend Erase WE# Enter Erase Suspend Program Erase Suspend Read Erase Resume Erase Suspend Program Erase Suspend Read Erase Erase Complete Q6 Q2 Note : The system can use OE# or CE# to toggle Q2/Q6, Q2 toggles only when read at an address within an erase-suspended P/N:PM1129 REV. 1.1 , JUL. 14, 2005 61 MX29LV320MT/B ERASE AND PROGRAMMING PERFORMANCE PARAMETER Sector Erase Time Typ (Note 1) Max (Note 2) Unit Comments 0.5 3.5 sec Excludes 00h programming Chip Erase Time 32 sec prior to erasure Note 6 Total Write Buffer Program Time (Note 4) 240 us Excludes Total Accelerated Effective Write Buffer 200 us system level Program Time (Note 4) Chip Program Time overhead 31.5 sec Note 7 Notes: 1. Typical program and erase times assume the following conditions: 25 C, 3.0 V VCC. Programming specifications assume checkerboard data pattern. 2. Maximum values are measured at VCC = 3.0 V, worst case temperature. Maximum values are valid up to and including 100,000 program/erase cycles. 3. Word/Byte programming specification is based upon a single word/byte programming operation not utilizing the write buffer. 4. For 1-16 words or 1-32 bytes programmed in a single write buffer programming operation. 5. Effective write buffer specification is calculated on a per-word/per-byte basis for a 16-word/32-byte write buffer operation. 6. In the pre-programming step of the Embedded Erase algorithm, all bits are programmed to 00h before erasure. 7. System-level overhead is the time required to execute the command sequence(s) for the program command. See Tables 3 for further information on command definitions. 8. The device has a minimum erase and program cycle endurance of 100,000 cycles. LATCH-UP CHARACTERISTICS MIN. MAX. Input Voltage with respect to GND on all pins except I/O pins -1.0V 13.5V Input Voltage with respect to GND on all I/O pins -1.0V VCC + 1.0V -100mA +100mA Current Includes all pins except VCC. Test conditions: VCC = 3.0V, one pin at a time. DATA RETENTION Parameter Minimum Pattern Data Retention Time P/N:PM1129 Min Unit 20 Years REV. 1.1 , JUL. 14, 2005 62 MX29LV320MT/B PACKAGE CAPACITANCE Parameter Symbol Parameter Description CIN Input Capacitance COUT CIN2 Output Capacitance Control Pin Capacitance Test Set VIN=0 VOUT=0 VIN=0 TYP MAX UNIT 6 7.5 pF CSP 4.2 5.0 pF TSOP/SOP 8.5 12 pF CSP 5.4 6.5 pF TSOP/SOP 7.5 9 pF CSP 3.9 4.7 pF TSOP/SOP Notes: 1. Sampled, not 100% tested. 2. Test conditions TA=25 C, f=1.0MHz P/N:PM1129 REV. 1.1 , JUL. 14, 2005 63 MX29LV320MT/B ORDERING INFORMATION PART NO. ACCESS TIME Ball Pitch/ (ns) Ball size PACKAGE MX29LV320MTMC-70R 70 44 Pin SOP MX29LV320MTMC-90 90 44 Pin SOP MX29LV320MBMC-70R 70 44 Pin SOP MX29LV320MBMC-90 90 44 Pin SOP MX29LV320MTMI-90 90 44 Pin SOP MX29LV320MBMI-90 90 44 Pin SOP MX29LV320MTTC-70R 70 48 Pin TSOP Remark (Normal Type) MX29LV320MTTC-90 90 48 Pin TSOP (Normal Type) MX29LV320MBTC-70R 70 48 Pin TSOP (Normal Type) MX29LV320MBTC-90 90 48 Pin TSOP (Normal Type) MX29LV320MTTI-90 90 48 Pin TSOP (Normal Type) MX29LV320MBTI-90 90 48 Pin TSOP (Normal Type) MX29LV320MTXBC-70R 70 0.8mm/0.3mm 48 Ball CSP MX29LV320MTXBC-90 90 0.8mm/0.3mm 48 Ball CSP MX29LV320MBXBC-70R 70 0.8mm/0.3mm 48 Ball CSP MX29LV320MBXBC-90 90 0.8mm/0.3mm 48 Ball CSP MX29LV320MTXBI-90 90 0.8mm/0.3mm 48 Ball CSP MX29LV320MBXBI-90 90 0.8mm/0.3mm 48 Ball CSP MX29LV320MTXEC-70R 70 0.8mm/0.4mm 48 Ball CSP MX29LV320MTXEC-90 90 0.8mm/0.4mm 48 Ball CSP MX29LV320MBXEC-70R 70 0.8mm/0.4mm 48 Ball CSP MX29LV320MBXEC-90 90 0.8mm/0.4mm 48 Ball CSP MX29LV320MTXEI-90 90 0.8mm/0.4mm 48 Ball CSP MX29LV320MBXEI-90 90 0.8mm/0.4mm 48 Ball CSP P/N:PM1129 REV. 1.1 , JUL. 14, 2005 64 MX29LV320MT/B PART NO. MX29LV320MTMC-90G MX29LV320MBMC-90G MX29LV320MTMI-90G MX29LV320MBMI-90G MX29LV320MTTC-90G ACCESS TIME (ns) 90 90 90 90 90 MX29LV320MBTC-90G 90 MX29LV320MTTI-90G 90 MX29LV320MBTI-90G 90 MX29LV320MTXBC-90G MX29LV320MBXBC-90G MX29LV320MTXBI-90G MX29LV320MBXBI-90G MX29LV320MTXEC-90G MX29LV320MBXEC-90G MX29LV320MTXEI-90G MX29LV320MBXEI-90G MX29LV320MTMC-70Q MX29LV320MBMC-70Q MX29LV320MTTC-70Q 90 90 90 90 90 90 90 90 70 70 70 MX29LV320MBTC-70Q 70 MX29LV320MTXBC-70Q MX29LV320MBXBC-70Q MX29LV320MTXEC-70Q MX29LV320MBXEC-70Q 70 70 70 70 Ball Pitch/ Ball size 0.8mm/0.3mm 0.8mm/0.3mm 0.8mm/0.3mm 0.8mm/0.3mm 0.8mm/0.4mm 0.8mm/0.4mm 0.8mm/0.4mm 0.8mm/0.4mm 0.8mm/0.3mm 0.8mm/0.3mm 0.8mm/0.4mm 0.8mm/0.4mm PACKAGE Remark 44 Pin SOP 44 Pin SOP 44 Pin SOP 44 Pin SOP 48 Pin TSOP (Normal Type) 48 Pin TSOP (Normal Type) 48 Pin TSOP (Normal Type) PB-free PB-free PB-free PB-free PB-free 48 Pin TSOP (Normal Type) 48 Ball CSP 48 Ball CSP 48 Ball CSP 48 Ball CSP 48 Ball CSP 48 Ball CSP 48 Ball CSP 48 Ball CSP 44 Pin SOP 44 Pin SOP 48 Pin TSOP (Normal Type) 48 Pin TSOP (Normal Type) 48 Ball CSP 48 Ball CSP 48 Ball CSP 48 Ball CSP PB-free PB-free PB-free PB-free PB-free PB-free PB-free PB-free PB-free PB-free PB-free PB-free PB-free PB-free PB-free PB-free PB-free PB-free PB-free Note : VCC operation range for -70R and -70Q is 3.0V~3.6V. P/N:PM1129 REV. 1.1 , JUL. 14, 2005 65 MX29LV320MT/B PACKAGE INFORMATION P/N:PM1129 REV. 1.1 , JUL. 14, 2005 66 MX29LV320MT/B P/N:PM1129 REV. 1.1 , JUL. 14, 2005 67 MX29LV320MT/B P/N:PM1129 REV. 1.1 , JUL. 14, 2005 68 MX29LV320MT/B P/N:PM1129 REV. 1.1 , JUL. 14, 2005 69 MX29LV320MT/B REVISION HISTORY Revision No. Description 1.0 1. Added TA=0 C to 70 C , VCC=3.0V~3.6V for 70Q operation 2. Removed "Advanced Information" 1.1 1. To correct content error 2. To add note 7 for ILIT parameter in DC Characteristics table 3. To add comments into performance table 4. To add tWPP2 parameter 5. To add "tPOLL" parameter into Automatic Program Waveform 6. To add "tASO", "tAS", "tAHT", "tCEPH" and "tOEPH" parameters into Toggle Bit Timing Waveform P/N:PM1129 Page P65 P1 P6,8,45 P31 P62 P49 P37 P59 Date MAR/11/2005 JUL/14/2005 REV. 1.1 , JUL. 14, 2005 70 MX29LV320MT/B MACRONIX INTERNATIONAL CO., LTD. Headquarters: TEL:+886-3-578-6688 FAX:+886-3-563-2888 Europe Office : TEL:+32-2-456-8020 FAX:+32-2-456-8021 Hong Kong Office : TEL:+86-755-834-335-79 FAX:+86-755-834-380-78 Japan Office : Kawasaki Office : TEL:+81-44-246-9100 FAX:+81-44-246-9105 Osaka Office : TEL:+81-6-4807-5460 FAX:+81-6-4807-5461 Singapore Office : TEL:+65-6346-5505 FAX:+65-6348-8096 Taipei Office : TEL:+886-2-2509-3300 FAX:+886-2-2509-2200 MACRONIX AMERICA, INC. TEL:+1-408-262-8887 FAX:+1-408-262-8810 http : //www.macronix.com MACRONIX INTERNATIONAL CO., LTD. reserves the right to change product and specifications without notice.