SEMiX404GB12E4s
© by SEMIKRON Rev. 0 – 05.05.2010 1
SEMiX® 4s
GB
Trench IGBT Modules
SEMiX404GB12E4s
Features
• Homogeneous Si
• Trench = Trenchgate technology
•V
CE(sat) with positive temperature
coefficient
• High short circuit capability
• UL recognized, file no. E63532
Typical Applications*
• AC inverter drives
•UPS
• Electronic Welding
Remarks
• Case temperature limited to TC=125°C
max.
• Product reliability results are valid for
Tj=150°C
• For short circuit: Soft RGoff
recommended RGoff > 25
• Dynamic values apply to the
following combination of resistors:
RGon,main = 1,0 Ω
RGoff,main = 1,0 Ω
RG,X = 2,2 Ω
RE,X = 0,5 Ω
Absolute Maximum Ratings
Symbol Conditions Values Unit
IGBT
VCES 1200 V
ICTj= 175 °C Tc=25°C 618 A
Tc=80°C 475 A
ICnom 400 A
ICRM ICRM = 3xICnom 1200 A
VGES -20 ... 20 V
tpsc
VCC = 800 V
VGE ≤ 20 V
VCES ≤ 1200 V
Tj= 150 °C 10 µs
Tj-40 ... 175 °C
Inverse diode
IFTj= 175 °C Tc=25°C 440 A
Tc=80°C 329 A
IFnom 400 A
IFRM IFRM = 3xIFnom 1200 A
IFSM tp= 10 ms, sin 180°, Tj=25°C 1980 A
Tj-40 ... 175 °C
Module
It(RMS) 600 A
Tstg -40 ... 125 °C
Visol AC sinus 50Hz, t = 1 min 4000 V
Characteristics
Symbol Conditions min. typ. max. Unit
IGBT
VCE(sat) IC=400A
VGE =15V
chiplevel
Tj=25°C 1.8 2.05 V
Tj= 150 °C 2.2 2.4 V
VCE0 Tj=25°C 0.8 0.9 V
Tj= 150 °C 0.7 0.8 V
rCE VGE =15V Tj=25°C 2.5 2.9 mΩ
Tj= 150 °C 3.8 4.0 mΩ
VGE(th) VGE=VCE, IC= 15.2 mA 5 5.8 6.5 V
ICES VGE =0V
VCE = 1200 V
Tj=25°C 0.12 0.36 mA
Tj= 150 °C mA
Cies VCE =25V
VGE =0V
f=1MHz 24.6 nF
Coes f=1MHz 1.62 nF
Cres f=1MHz 1.38 nF
QGVGE =- 8 V...+ 15 V 2260 nC
RGint Tj=25°C 1.88 Ω
td(on) VCC = 600 V
IC=400A
RG on =1.7Ω
RG off =1.7Ω
di/dton = 5800 A/µs
di/dtoff = 3700 A/µs
Tj= 150 °C 296 ns
trTj= 150 °C 67 ns
Eon Tj= 150 °C 27 mJ
td(off) Tj= 150 °C 634 ns
tfTj= 150 °C 137 ns
Eoff Tj= 150 °C 59.7 mJ
Rth(j-c) per IGBT 0.072 K/W
http://store.iiic.cc/
SEMiX404GB12E4s
2 Rev. 0 – 05.05.2010 © by SEMIKRON
Characteristics
Symbol Conditions min. typ. max. Unit
Inverse diode
VF = VEC IF=400A
VGE =0V
chip
Tj=25°C 2.2 2.52 V
Tj= 150 °C 2.1 2.5 V
VF0 Tj=25°C 1.1 1.3 1.5 V
Tj= 150 °C 0.7 0.9 1.1 V
rFTj=25°C 2.0 2.3 2.5 mΩ
Tj= 150 °C 2.6 3.1 3.4 mΩ
IRRM IF=400A
di/dtoff = 4900 A/µs
VGE =-15V
VCC = 600 V
Tj= 150 °C 315 A
Qrr Tj= 150 °C 63 µC
Err Tj= 150 °C 26.4 mJ
Rth(j-c) per diode 0.14 K/W
Module
LCE 22 nH
RCC'+EE' res., terminal-chip TC=25°C 0.7 mΩ
TC= 125 °C 1mΩ
Rth(c-s) per module 0.03 K/W
Msto heat sink (M5) 3 5 Nm
Mtto terminals (M6) 2.5 5 Nm
Nm
w400 g
Temperatur Sensor
R100 Tc=100°C (R25=5 kΩ) 493 ± 5% Ω
B100/125
R(T)=R100exp[B100/125(1/T-1/T100)];
T[K];
3550
±2% K
SEMiX® 4s
GB
Trench IGBT Modules
SEMiX404GB12E4s
Features
• Homogeneous Si
• Trench = Trenchgate technology
•V
CE(sat) with positive temperature
coefficient
• High short circuit capability
• UL recognized, file no. E63532
Typical Applications*
• AC inverter drives
•UPS
• Electronic Welding
Remarks
• Case temperature limited to TC=125°C
max.
• Product reliability results are valid for
Tj=150°C
• For short circuit: Soft RGoff
recommended RGoff > 25
• Dynamic values apply to the
following combination of resistors:
RGon,main = 1,0 Ω
RGoff,main = 1,0 Ω
RG,X = 2,2 Ω
RE,X = 0,5 Ω
http://store.iiic.cc/
SEMiX404GB12E4s
© by SEMIKRON Rev. 0 – 05.05.2010 3
Fig. 1: Typ. output characteristic, inclusive RCC'+ EE' Fig. 2: Rated current vs. temperature IC = f (TC)
Fig. 3: Typ. turn-on /-off energy = f (IC)Fig. 4: Typ. turn-on /-off energy = f (RG)
Fig. 5: Typ. transfer characteristic Fig. 6: Typ. gate charge characteristic
http://store.iiic.cc/
SEMiX404GB12E4s
4 Rev. 0 – 05.05.2010 © by SEMIKRON
Fig. 7: Typ. switching times vs. ICFig. 8: Typ. switching times vs. gate resistor RG
Fig. 9: Typ. transient thermal impedance Fig. 10: Typ. CAL diode forward charact., incl. RCC'+EE'
Fig. 11: Typ. CAL diode peak reverse recovery current Fig. 12: Typ. CAL diode recovery charge
http://store.iiic.cc/
SEMiX404GB12E4s
© by SEMIKRON Rev. 0 – 05.05.2010 5
This is an electrostatic discharge sensitive device (ESDS), international standard IEC 60747-1, Chapter IX
* The specifications of our components may not be considered as an assurance of component characteristics. Components have to be tested
for the respective application. Adjustments may be necessary. The use of SEMIKRON products in life support appliances and systems is
subject to prior specification and written approval by SEMIKRON. We therefore strongly recommend prior consultation of our personal.
SEMiX 4s
spring configuration
http://store.iiic.cc/
