shrinkHOoP is a Trademark of Tyco Electronics
Specification Control Drawing
Tyco Electronics Corporation
300 Constitution Drive
Menlo Park, CA 94025 USA
Title:
shrinkHOoP –Cable Clamp Heat
Shrink Grommet
Tyco Electronics reserves the right to amend this drawing at any time.
Users should evaluate the suitability of the product for their application. Document No.
URHR-1-and-5
UNLESS OTHERWISE SPECIFIED DI MENSI O NS ARE I N I NCHES.
METRIC DIMENSIONS ARE SHOWN IN BRACKETS
Rev.:
F
Rev. Date:
December 9, 2004
DRAWN BY:
U.NGUYEN
CAGE CODE:
06090
Org. Date:
10/03/2001
File name:
R040892
SCALE:
None
SIZE:
A
SHEET:
1 of 2
©2004 Tyco Electronics Corporation. All rights reserved
If this document is printed it becomes uncontrolled. Check for the latest revision.
shrinkHOoP
Cable Clamp Heat Shrink Grommet Sizes 1 and 5
c
b
a
L
Table of Dimensions, inch (mm):
Inside Diameter
Part
Descriptio
n
Min. Exp. (a)
Max. Rec’d
(b)
Outside
Diameter
Recovered
(c), Ref
Overall
Length
Recovered
L, Ref
URHR-1 1.00 (25) 0.08 (2.0) 0.250 (6.3) 0.50 (13)
URHR-5 2.00 (51) 0.20 (5.1) 0.812 (20.5) 0.75 (19)
Material: heat shrinkable, crosslinked polyolefin, meets MIL-I-81765/1 Type II with
Shore Hardness value 35+/- 5.
Color: Black
shrinkHOoP is a Trademark of Tyco Electronics
Specification Control Drawing
Rev. Date:
Dec. 9, 2004
Rev.:
F
Document No.
URHR-1-and-5
Sheet:
2 of 2
If this document is printed it becomes uncontrolled. Check for the latest revision.
Table 2: Properties
Property Requirements Test method
Tensile strength 1200 psi (8.3 Mpa) minimum ASTM D-412
Ultimate elongation 250% minimum ASTM D-412
Specific gravity 1.4 maximum ASTM D-792
Water absorption 0.5% maximum ASTM D-570
Hardness, Shore D 35 ± 5 ASTM D-2240
Flammability
Pass
ASTM D-635
Corrosion resistance Pass MIL-I-81765
Low temperature flex
4 hours at –67 ± 2°F (-55 ±
1°C)
Pass MIL-I-81765
Heat resistance
168 hours at 347 ± 2°F
(175 ± 1°C)
200% ultimate elongation,
minimum
1000 psi (6.9 Mpa) tensile
strength, minimum
MIL-I-81765
Physical
Heat shock
4 hours at 437 ± 5°F (225 ±
2°C)
No cracking, dripping or
flowing MIL-I-81765
Elastic Memory 275% minimum expansion to 4 inch (10 cm) of
a fully recovered test specimen, and 93%
recovery of expanded specimen after oven
condition for 1 minute at 302 ± 4°F (150 ± 2° C)
Dielectric strength 200 v/mil (7880 v/mm)
minimum ASTM D-149
Electrica
l Volume resistivity 10
12
ohm-cm minimum ASTM D-257
Chemical
Fluid Resistance 200% ultimate elongation,
minimum
750 psi (5.2 Mpa) tensile
strength, minimum
MIL-I-81765
