FUJITSU MICROELECTRONICS DATA SHEET DS04-27604-2Ea ASSP For Power Supply Applications Power Management 2-ch Switch IC MB3842/MB3845 DESCRIPTION The MB3842/3845 is a power management switch with built-in 2-channel low-on resistance (typ. 100m) switch. Output control is by means of a control signal, and the MB3842 is designed for high-active operation (output on when EN is Hi), while the MB3845 is designed for low-active operation (output on when EN is low.) To provide adaptability to a variety of operations, the MB3842/3845 features low input voltage (VIN > 2.5V) operation and stable low-on resistance independent of input voltage. The switching current limit can be set from 100mA to 600mA by using external resistance, and when overcurrent conditions are detected the OC output goes low to provide an external notification signal. VIN is divided between the two channels, which operate independently of each other. In addition, an off-state reverse current prevention function is provided to ensure accurate on/off switching action. FEATURES * * * * * * * * * * Low on resistance switch (typ. 100m) Low input voltage operation (2.5 V to 5.5 V) Switch current (max. 0.6 A) UVLO :VIN threshold 2.3V/2.1 V hysteresis 200 mV ENABLE :EN threshold EN 1.4V/1.6 V for MB3842, EN 1/2 VIN for MB3845 :Power supply current at output off = 0A EN < 0.8V for MB3842, EN = VIN for MB3845 External setting for soft start time and switch current limit. Over-temperature detection (switch latched off), over-current detection (not latched) OC pin flag set following overcurrent detection, over-temperature detection, or UVLO detection. Reverse current prevention at OFF (VIN 1.5 V) Either channel may be operated alone. PACKAGE 20-pin plastic SSOP (FPT-20P-M03) Copyright(c)2000-2008 FUJITSU MICROELECTRONICS LIMITED All rights reserved 2000.1 MB3842/MB3845 PIN ASSIGNMENT EN1, EN1 1 20 GND SS1 2 19 OC1 CS1 3 18 OUT1 VIN1 4 17 OUT1 SSOP-20P (FPT-20P-M03) VIN1 5 16 OUT1 VIN2 6 15 OUT2 VIN2 7 14 OUT2 CS2 8 13 OUT2 SS2 9 12 OC2 EN2, EN2 10 11 GND EN Enable EN Enable CS Current Set OC Over Current SS Slow Start The functions of pin 1 and pin 10 differ on the MB3842 and MB3845. EN for MB3842/EN for MB3845 2 MB3842/MB3845 PIN DESCRIPTION Pin no. Symbol Descriptions EN (MB3842) Control signal input pin. Set "H" to turn switch on, "L" to turn toff. At 0.8 V or less, the chip is in STBY state and current consumption is less than 1A. "L" level is 1.4V (typ), "H" level is 1.6V (typ), with 200mV (typ) hysteresis. EN (MB3845) Control signal input pin. Set "L" to turn switch on, "H" to turn off. At "H" level = VIN, the chip is in STBY state and current consumption is less than 1A. Normally used as CMOS inverter input, so that recommended use is "L" level at GND +0.5V or less, and "H" level is VIN -0.5V or greater. 2/9 SS Slow start setting pin. Used to adjust the switch on/off timing. Add external capacitance to delay operation. Leave open when not in use. In open mode voltages up to 12 V are present. Care should be taken in mounting to prevent leakage current generation because high impedance is required. 3/8 CS Current limit setting pin. The limit current level is set by connecting this pin to external resistance. 4/5/6/7 VIN Switch output pin. An UVLO (VIN power monitor function) is provided so that when VIN reaches 2.3V (typ.) or higher the OC pin voltage goes to "H" level. Also if the VIN voltage drops to 2.1 V (typ.) or lower the OC output goes to "L" state. 200mV (typ) hysteresis is provided. 11/20 GND Ground pin. 1/10 12/19 OC 13/14/15 16/17/18 OUT External notification pin. When the switch is in on mode this pin normally outputs a "H" level signal, but changes to "L" level when an overcurrent, overtemperature, or UVLO condition is detected. This is an open drain connection, and should be pulled up to high potential using resistance. Switching output pin.(N-ch MOSFET source) 3 MB3842/MB3845 BLOCK DIAGRAM (for 1 channel) MB3842 OUT1 SS1 CS1 Over current detection 1 Charge pump1 Q S + COMP - FF1 R EN1 + COMP - OSC1 OC1 VIN1 BGR1 Temperature protection 1 MB3845 OUT1 Charge pump1 SS1 CS1 Over current detection 1 Q S + COMP - FF1 R EN1 OSC1 VIN1 BGR1 Temperature protection 1 4 + COMP - OC1 MB3842/MB3845 ABSOLUTE MAXIMUM RATINGS Parameter Symbol Condition Input voltage VIN ENABLE voltage Rating Unit Max. Min. -- -0.3 7.0 V VEN -- -0.3 7.0 V Switch current ISW -- -- 1.8 A Power dissipation PD -- 216 mW -55 +125 C Storage temperature Ta = +85C TSTG -- WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings. RECOMMENDED OPERATING CONDITIONS Parameter Symbol Condition Input voltage VIN -- ENABLE voltage VEN Switch current ISW SS pin capacitance CSS* OC sink current IOCS Current limit resistance RLIM* Operating temperature TOP Value Unit Min. Typ. Max. 2.5 5.0 5.5 V VEN VIN 0 -- 5.5 V VIN = 2.5 V to 5.5 V -- -- 0.6 A -- -- 10 nF VIN = 5.0 V, VOC = 0.4 V 2.0 5.0 -- mA VIN = 5.0 V (ISW = 0.6 A) 1.4 2.0 2.6 k VIN = 5.0 V (ISW = 0.1 A) 3.6 6.2 9.1 k -20 -- +85 C -- -- * : For CSS, RLIM settings, see "TYPICAL CHARACTERISTICS" and "FUNCTIONAL DESCRIPTION". WARNING: The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All of the device's electrical characteristics are warranted when the device is operated within these ranges. Always use semiconductor devices within their recommended operating condition ranges. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users considering application outside the listed conditions are advised to contact their representatives beforehand. 5 MB3842/MB3845 ELECTRICAL CHARACTERISTICS (per 1 ch) * MB3842/MB3845 Parameter Switch resistance IN pin input current UVLO threshold UVLO hysteresis width Switch current limit OC sink current Symbol Condition Min. RON ISW =0.6A -- 100 150 m IIN1 ISW = 0 A -- 350 550 A IIN2 ISW = 0.6 A -- 1.0 1.5 mA IIN3 EN < 0.8V for MB3842, EN = VIN for MB3845 -- -- 1.0 A VIUH VIN at OC = L H 2.1 2.3 2.5 V VIUL VIN at OC = H L 1.9 2.1 2.3 V VIUHY VIUHY = VIUH - VIUL 100 200 300 mV ISWH RLIM = 2.0 k 0.42 0.6 0.78 A ISWL RLIM = 6.2 k 0.06 0.1 0.14 A IOCS VOC = 0.4 V at OC active 2.0 5.0 -- mA IOCL VOC = 5.0 V at OC non-active -- -- 1.0 A +125 -- -- C Temperature protection (Tj) TLIM OUT pin rise time tON SS pin: Open OUT pin: 100 k pull down -- 100 200 s OUT pin fall time tOFF SS pin: Open OUT pin: 100 k pull down -- 50 120 s -- * MB3842 Parameter ENABLE pin input current Symbol Condition Min. (VIN = 5 V, Ta = +25C) Value Unit Typ. Max. IENH VEN = 5 V, ISW = 0 A -- 5 10 A IENL VEN = 0 V, ISW = 0 A -- 0.0 -- A ENABLE pin threshold voltage VTHEN -- 1.45 1.60 1.75 V VTLEN -- 1.25 1.40 1.55 V ENABLE hysteresis width VENHY VENHY = VTHEN - VTLEN 100 200 300 mV * MB3845 Parameter ENABLE pin input current ENABLE pin input voltage 6 (VIN = 5 V, Ta = +25C) Value Unit Typ. Max. Symbol Condition Min. (VIN = 5 V, Ta = +25C) Value Unit Typ. Max. IENH VEN = 5 V, ISW = 0 A -- 0.0 -- A IENL VEN = 0 V, ISW = 0 A -- 0.0 -- A VILEN -- 0 -- 0.8 V VIHEN -- 3.0 -- 5.0 V MB3842/MB3845 DIAGRAM * Normal operation 5V VIN Hi EN EN Low SW OFF SW ON SW ON 5V VOUT IOUT Overcurrent does not occur OC 5V * At VIN fall 5V 2.3 V VIN 2.1 V Hi EN EN Low SW ON SW ON SW ON 5V VOUT Overcurrent does not occur IOUT 5V OC =0V Note: The OC pin should be pulled up using a separate power supply and resistance. (This illustration shows pull-up with a separate 5V source.) (Continued) 7 MB3842/MB3845 (Continued) * At overcurrent detection 5V VIN Hi EN EN Low SW ON OFF ON OFF 5V VOUT IOUT 5V OC =0V * At over-temperature occurrence 5V VIN Over-temperature occurs Over-temperature corrected Hi EN EN Low SW ON SW OFF 5V VOUT Overcurrent does not occur IOUT 5V OC =0V Latch set Latch released Note: The OC pin should be pulled up using a separate power supply and resistance. (This illustration shows pull-up with a separate 5V source.) 8 MB3842/MB3845 TYPICAL CHARACTERISTICS * RLIM vs. limit current characteristics These are the limiting value characteristics for CS pin-to-GND external resistance and output current (OC flag). 10 ISW(A) 1 VIN = 5.0 V VIN = 3.3 V VIN = 2.5 V 0.1 0.01 100 1000 10000 100000 RLIM () * CSS vs. TON (SS) characteristics There are the characteristics for SS pin-to-GND external capacitance and output ON time. 100 tON(ms) 10 VIN = 5.0 V VIN = 3.3 V VIN = 2.5 V 1 0.1 10 100 1000 10000 100000 CSS (pF) (Continued) 9 MB3842/MB3845 (Continued) * SW resistance vs. temperature characteristics 150 140 SW resistance (m) 130 120 110 at 0.1 A at 0.6 A at 1 A 100 90 80 70 60 50 -60 -40 -20 0 20 40 60 80 100 120 Temperature Ta (C) * Temperature-depended SW resistance vs. VIN (V) characteristics 150 SW resistance (m) 140 130 120 110 -40 C 25 C 100 C 100 90 80 70 60 50 2 3 4 5 6 7 VIN voltage (V) (Continued) 10 MB3842/MB3845 (Continued) * Output power (ISW) saturation characteristics 5V Measurement circuit VIN EN, EN VIL/VIH "Open" OC ISW SS OUT CS A GND 2 100 k RLIM VSW 5V These are the output saturation current characteristics in overcurrent state.(when not controlled by the OC pin warning flag) 1600 1400 RLIM not limited (CS GND) 1200 ISW (mA) 1000 RLIM set to 2.0k, 0.6A Unlimited 6.2 k (0.1 A) 2 k (0.6 A) 800 Overcurrent flag set (when set for 0.6A) 600 Temperature protection range 400 RLIM set to 6.2k, 0.1A Overcurrent flag set (when set for 0.1A) 200 0 0 1 2 3 VSW (V) 4 5 6 (Continued) 11 MB3842/MB3845 (Continued) * OC pin flag pull-up resistance (pull-up power 5V) dependant overcurrent operation 1 V / 500 NS 1 k 1 V / 500 NS 50 k 1 V / 500 NS 10 k 1 V / 500 NS 100 k GND * Power derating characteristics 1 0.9 Power dissipation PD (W) 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 -20 0 20 40 Temperature Ta (C) 12 60 80 100 MB3842/MB3845 FUNCTIONAL DESCRIPTION Current Limit Setting By placing resistance between the CS and GND pins, the current limit can be set between 100mA and 600mA within 30% accuracy (VIN = 5 V, current limit at 600mA). Because the setting value is dependent on VIN voltage, the user should select the optimum resistance value for the value of VIN voltage . When the switching current exceeds the set value, the OC pin goes to "L" level as an external notification signal, but there is no latching function. To hold operation on "off" state, the input signal to the EN and EN pins should be used. When a direct connection to GND is used, there is no current limitation. When the connection is open, the switch is in a state of continuously held current limits. Thermal Shutdown The MB3842/MB3845 has a thermal shutdown function which turns the switch off and sets the latch to protect the device when junction temperature exceeds 125C. At the same time the OC output signal goes to "L" level to notify external systems. The latch function can be reset by sending a low signal to the EN input of the MB3842, or a high signal to the EN input of the MB3845. Slow Start The on/off switching time can be delayed by applying capacitance between the SS and GND pins. Controlling the on time can soften surge current to the load side capacitance when power is turned on. For details, see "Css vs. tON (SS) characteristics" on p. 9. UVLO A VIN voltage monitoring function is provided, so that when VIN voltage exceeds 2.3 V (typ) the OC pin voltage goes to "H" level. When VIN voltage falls below 2.1V (typ), the OC output goes to "L" state. Error Flag OC Pin The OC pin produces a "L" signal in case of a UVLO, overcurrent, or over-temperature condition. In case of overcurrent, the output has a pulse waveform. See P12. (note) Output current limit setting resistance values are shown on P9, and in the following table. (CS pin-to-GND) Standard Values VIN/ISW 0.1 A 0.2 A 0.3 A 0.4 A 0.5 A 0.6 A 0.7 A 0.8 A 0.9 A 1.0 A VIN 5.0V 6.2 k 4.3 k 3.3 k 2.7 k 2.2 k 2.0 k 1.8 k 1.6 k 1.4 k 1.3 k VIN 3.3V 9.1 k 5.6 k 4.3 k 3.3 k 2.7 k 2.4 k 2.0 k 1.8 k 1.6 k 1.5 k VIN 2.5V 13 k 7.5 k 5.1 k 3.9 k 3.0 k 2.7 k 2.2 k 2.0 k 1.8 k 1.6 k 13 MB3842/MB3845 TYPICAL APPLICATION Top View MB3842/MB3845 EN1 EN1 Control signal GND Pull-up resistance CSS SS1 OC1 CS1 OUT1 VIN1 OUT1 VIN1 OUT1 VIN2 OUT2 VIN2 OUT2 CS2 OUT2 RLIM Load Load RLIM Pull-up resistance CSS Control signal 14 SS2 OC2 EN2 EN2 GND MB3842/MB3845 APPLICATION EXAMPLE (1) Dual-Port Self-Powered Hub Application (NON-GANG Mode Connection) USB 5 V Controller Overcurrent MB3842/MB3845 ON/OFF Power Supply EN1,EN1 GND SS1 OC1 CS1 OUT1 VIN1 OUT1 USB Port 1 VIN1 OUT1 VIN2 OUT2 5V USB Port 2 VIN2 OUT2 CS2 OUT2 SS2 OC2 EN2,EN2 GND *The MB3842 can also be adapted for use with 3.3V controllers. USB Port 500mA MAX Par Port Smoothing capacitors should be placed between VIN and GND, or between OUT and GND as required. 15 MB3842/MB3845 (2) Dual-Port Bus Powered Hub Application (GANG Mode Connection) USB Overcurrent MB3842/MB3845 ON/OFF EN1,EN1 GND SS1 OC1 CS1 OUT1 VIN1 OUT1 USB Port1(x4) 400 mA MAX (100 mA x4) 5V Upstream Port VIN1 OUT1 VIN2 OUT2 VIN2 OUT2 CS2 OUT2 USB Port2(x4) 400 mA MAX (100 mA x4) SS2 OC2 EN2,EN2 GND USB Port 100mA MAX Par Port Smoothing capacitors should be placed between VIN and GND, or between OUT and GND as required. 16 MB3842/MB3845 USAGE PRECAUTION 1. Never use settings exceeding maximum rated conditions. Exceeding maximum rated conditions may cause permanent damage to the LSI. Also, it is recommended that recommended operating conditions be observed in normal use. Exceeding recommended operating conditions may adversely affect LSI reliability. 2. Use this device within recommended operating conditions. Recommended operating conditions are values within which normal LSI operation is warranted. Standard electrical characteristics are warranted within the range of recommended operating conditions and within the listed conditions for each parameter. 3. Printed circuit board ground lines should be set up with consideration for common impedance. 4. Take appropriate static electricity measures. * * * * Containers for semiconductor materials should have anti-static protection or be made of conductive material. After mounting, printed circuit boards should be stored and shipped in conductive bags or containers. Work platforms, tools, and instruments should be properly grounded. Working personnel should be grounded with resistance of 250 k to 1 M between body and ground. 5. Do not apply negative voltages. The use of negative voltages below -0.3 V may create parasitic transistors on LSI lines, which can cause abnormal operation. 6. Reverse Current Prevention Function Current cannot flow back to the VIN pin with the switch off, even when the OUT pin voltage is higher than the VIN pin (OUT VIN), however when VIN pin voltage is lower than 1.5 V circuit functions are lost, so that in this case there is danger of reverse current flow. For applications in which reverse flow is not acceptable, set VIN 1.5 V. ORDERING INFORMATION Part number MB3842PFV MB3845PFV MB3845PFV-ER Package Remarks 20-pin Plastic SSOP (FPT-20P-M03) 17 MB3842/MB3845 PACKAGE DIMENSION *: These dimensions do not include resin protrusion. 20-pin plastic SSOP (FPT-20P-M03) +0.20 * 6.500.10(.256.004) 1.25 -0.10 +.008 .049 -.004 (Mounting height) 0.10(.004) INDEX 0.650.12 (.0256.0047) 5.85(.230)REF C 18 1994 FUJITSU LIMITED F20012S-2C-4 * 4.400.10 6.400.20 (.173.004) (.252.008) +0.10 "A" 5.40(.213) NOM +0.05 0.22 -0.05 0.15 -0.02 +.004 -.002 .006 -.001 .009 Details of "A" part +.002 0.100.10(.004.004) (STAND OFF) 0 10 0.500.20 (.020.008) Dimensions in mm (inches). MB3842/MB3845 MEMO 19 FUJITSU MICROELECTRONICS LIMITED Shinjuku Dai-Ichi Seimei Bldg. 7-1, Nishishinjuku 2-chome, Shinjuku-ku, Tokyo 163-0722, Japan Tel: +81-3-5322-3347 Fax: +81-3-5322-3387 http://jp.fujitsu.com/fml/en/ For further information please contact: North and South America FUJITSU MICROELECTRONICS AMERICA, INC. 1250 E. Arques Avenue, M/S 333 Sunnyvale, CA 94085-5401, U.S.A. Tel: +1-408-737-5600 Fax: +1-408-737-5999 http://www.fma.fujitsu.com/ Asia Pacific FUJITSU MICROELECTRONICS ASIA PTE LTD. 151 Lorong Chuan, #05-08 New Tech Park, Singapore 556741 Tel: +65-6281-0770 Fax: +65-6281-0220 http://www.fujitsu.com/sg/services/micro/semiconductor/ Europe FUJITSU MICROELECTRONICS EUROPE GmbH Pittlerstrasse 47, 63225 Langen, Germany Tel: +49-6103-690-0 Fax: +49-6103-690-122 http://emea.fujitsu.com/microelectronics/ FUJITSU MICROELECTRONICS SHANGHAI CO., LTD. Rm.3102, Bund Center, No.222 Yan An Road(E), Shanghai 200002, China Tel: +86-21-6335-1560 Fax: +86-21-6335-1605 http://cn.fujitsu.com/fmc/ Korea FUJITSU MICROELECTRONICS KOREA LTD. 206 KOSMO TOWER, 1002 Daechi-Dong, Kangnam-Gu,Seoul 135-280 Korea Tel: +82-2-3484-7100 Fax: +82-2-3484-7111 http://www.fmk.fujitsu.com/ FUJITSU MICROELECTRONICS PACIFIC ASIA LTD. 10/F., World Commerce Centre, 11 Canton Road Tsimshatsui, Kowloon Hong Kong Tel: +852-2377-0226 Fax: +852-2376-3269 http://cn.fujitsu.com/fmc/tw All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with sales representatives before ordering. The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of FUJITSU MICROELECTRONICS device; FUJITSU MICROELECTRONICS does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. FUJITSU MICROELECTRONICS assumes no liability for any damages whatsoever arising out of the use of the information. Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU MICROELECTRONICS or any third party or does FUJITSU MICROELECTRONICS warrant non-infringement of any third-party's intellectual property right or other right by using such information. FUJITSU MICROELECTRONICS assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite). Please note that FUJITSU MICROELECTRONICS will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. Exportation/release of any products described in this document may require necessary procedures in accordance with the regulations of the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws. The company names and brand names herein are the trademarks or registered trademarks of their respective owners. Edited Strategic Business Development Dept.