1500 MHz SAW Filter 6 MHz Bandwidth Part Number SF1500BA03201S DESCRIPTION * * * 1500 MHz SAW bandpass filter with 6 MHz bandwidth. 3.8 x 3.8 mm ceramic LCC package. RoHS compliant. TYPICAL PERFORMANCE Amp 10 dB/div Amp 1 dB/div Phase 10 deg/div Delay 50 ns/div Center = 1500 MHz, 20 MHz/div (125 kHz incr) S11 (1400-1600 MHz) S22 (1400-1600 MHz) IDT * SAW Products * 324 Clark Street, Worcester, MA 01606, USA * Ph 1-508-852-5400 * Fax 1-508-852-8456 www.idt.com DSSF1500BA03201S Rev 5-Nov-2008 ECN 36213 Page 1 of 3 1500 MHz SAW Filter 6 MHz Bandwidth Part Number SF1500BA03201S SPECIFICATION Parameter 1 Center Frequency, FC Insertion Loss Passband Ripple (1497-1503 MHz) Phase Ripple (1497-1503 MHz) Group Delay Deviation (1497-1503 MHz) 24MHz) Delay Absolute 2 3 dB bandwidth 2 Lower 3 dB Frequency 2 Upper 3 dB Frequency 2 30 dB Bandwidth 2 40 dB bandwidth Relative Attenuation (1400-1465 MHz) Relative Attenuation (1530-1600 MHz) Input /Output Return Loss at Fc Source and Load Impedance Temperature Coefficient of Frequency Ambient Temperature Notes: Min 1490 6 1503 38 35 6 - Typ 1500 3.9 0.8 3 10 52 18.5 1488.2 1506.7 40.8 48.9 42 38 10 50 -32 25 Max 1510 6 2 5 20 21 1497 - - Units MHz dB dB p-p deg p-p ns p-p ns MHz MHz MHz MHz MHz dB dB dB ohms ppm/C C 1. Reference frequency. Computed as mean of the 3 dB frequencies. 2. All dB values are referenced to the insertion loss value. MAXIMUM RATINGS Parameter Storage Temperature Range Operating Temperature Range Input Power Level Min Max -40 -30 - 100 100 13 Units C C dBm MATCHING CIRCUIT 2 5 Input 50 Single ended Output 50 Single ended All other pads Notes: * Matching components are not required. * Operation is in a 50 ohm single-ended system. IDT * SAW Products * 324 Clark Street, Worcester, MA 01606, USA * Ph 1-508-852-5400 * Fax 1-508-852-8456 www.idt.com DSSF1500BA03201S Rev 5-Nov-2008 ECN 36213 Page 2 of 3 1500 MHz SAW Filter 6 MHz Bandwidth Part Number SF1500BA03201S PACKAGE OUTLINE Units: mm Tolerances are typically 0.15 mm except where indicated. IDT 3201 YYWW Pad Configuration: Input: 2 Output: 5 Ground: All other pads Date Code (YY=year, WW= week) Package Material: Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 1 m min, over a 1.3-8.9 m Ni plating ISO 9001 Registered All specifications are believed to be accurate and reliable. However, MNC reserves the right to make changes without notice. (c) 2008 All rights reserved. IDT * SAW Products * 324 Clark Street, Worcester, MA 01606, USA * Ph 1-508-852-5400 * Fax 1-508-852-8456 www.idt.com DSSF1500BA03201S Rev 5-Nov-2008 ECN 36213 Page 3 of 3