ESD7205 ESD Protection Diode Low Capacitance ESD Protection Diodes for High Speed Data Line The ESD7205 ESD protection diode array is designed to protect high speed data lines from ESD. Ultra-low capacitance and low ESD clamping voltage make this device an ideal solution for protecting voltage sensitive high speed data lines. The small form factor, flow-through style package allows for easy PCB layout and matched trace lengths necessary to maintain consistent impedance between high speed differential lines such as Ethernet and LVDS present in automotive camera modules. * Low Capacitance (0.4 pF Typical, I/O to GND) * Diode capacitance matching * Protection for the Following IEC Standards: * IEC 61000-4-2 Level 4 (ESD) Low ESD Clamping Voltage (12 V Typical, +16 A TLP, I/O to GND) SZ Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC-Q101 Qualified and PPAP Capable These Devices are Pb-Free and are RoHS Compliant Typical Applications * * * * * MARKING DIAGRAMS SOT-723 CASE 631AA 100BASE-T1 / OPEN Alliance BroadR-Reach Automotive Ethernet 10/100/1000BASE-T1 Ethernet LVDS Automotive USB 2.0/3.0 High Speed Differential Pairs EA M 1 EA M Features * * www.onsemi.com = Specific Device Code = Date Code SC-70 CASE 419 ECMG G 1 EC = Specific Device Code M = Date Code G = Pb-Free Package (Note: Microdot may be in either location) PIN CONFIGURATION AND SCHEMATIC Pin 1 Pin 2 MAXIMUM RATINGS (TJ = 25C unless otherwise noted) Rating Symbol Value Unit Operating Junction Temperature Range TJ -55 to +150 C Storage Temperature Range Tstg -55 to +150 C Lead Solder Temperature - Maximum (10 Seconds) TL 260 C ESD 25 25 20 30 30 kV IEC 61000-4-2 Contact IEC 61000-4-2 Air ISO 10605 330 pF / 330 W Contact ISO 10605 330 pF / 2 kW Contact ISO 10605 150 pF / 2 kW Contact Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. (c) Semiconductor Components Industries, LLC, 2016 January, 2019 - Rev. 6 1 Pin 3 = ORDERING INFORMATION See detailed ordering, marking and shipping information in the package dimensions section on page 6 of this data sheet. Publication Order Number: ESD7205/D ESD7205 ELECTRICAL CHARACTERISTICS I (TA = 25C unless otherwise noted) IF Parameter Symbol IPP Maximum Reverse Peak Pulse Current VC Clamping Voltage @ IPP VRWM IR VBR IT VC VBR VRWM Working Peak Reverse Voltage V IR VF IT Maximum Reverse Leakage Current @ VRWM Breakdown Voltage @ IT Test Current *See Application Note AND8308/D for detailed explanations of datasheet parameters. IPP Uni-Directional ELECTRICAL CHARACTERISTICS (TA = 25C unless otherwise specified) Parameter Reverse Working Voltage Breakdown Voltage Symbol Conditions VRWM I/O Pin to GND Min Max Unit 5.0 V VBR IT = 1 mA, I/O Pin to GND Reverse Leakage Current IR VRWM = 5.0 V, I/O Pin to GND Clamping Voltage (Note 1) VC IEC61000-4-2, 8 kV Contact See Figures 3 and 4 Clamping Voltage TLP (Note 2) VC IPP = 8 A IPP = 16 A IPP = -8 A IPP = -16 A 10 12.5 -4.0 -8.0 Junction Capacitance Match DCJ VR = 0 V, f = 1 MHz between I/O1 to GND and I/O 2 to GND 5 10 Junction Capacitance CJ VR = 0 V, f = 1 MHz between I/O Pins and GND ESD7205DT5G ESD7205WTT1G 0.34 0.47 0.55 0.85 VR = 0 V, f = 1 MHz between I/O Pins ESD7205DT5G ESD7205WTT1G 0.20 0.23 0.35 0.40 3dB Bandwidth fBW RL = 50 W 5.2 Typ 6.0 5 1. For test procedure see Figures 5 and 6 and application note AND8307/D. 2. ANSI/ESD STM5.5.1 - Electrostatic Discharge Sensitivity Testing using Transmission Line Pulse (TLP) Model. TLP conditions: Z0 = 50 W, tp = 100 ns, tr = 4 ns, averaging window; t1 = 30 ns to t2 = 60 ns. www.onsemi.com 2 8.0 V 1 mA V % pF GHz ESD7205 1.E-02 1.0 1.E-03 0.9 0.8 0.7 1.E-06 0.6 I (A) C (pF) 1.E-04 1.E-05 1.E-07 1.E-08 0.4 1.E-09 0.3 1.E-10 0.2 1.E-11 0.1 1.E-12 -2 -1 0 1 2 3 4 5 6 7 8 9 10 1 2 3 5 4 V (V) VBias (V) Figure 2. CV Characteristics 10 80 0 70 -10 60 -20 VOLTAGE (V) VOLTAGE (V) 0 0 Figure 1. IV Characteristics 90 50 40 30 20 -30 -40 -50 -60 10 -70 0 -80 -10 -20 I/O-GND 0.5 0 20 40 60 80 TIME (ns) 100 120 140 -90 -20 Figure 3. IEC61000-4-2 +8 kV Contact ESD Clamping Voltage 0 20 40 60 80 TIME (ns) 100 120 Figure 4. IEC61000-4-2 -8 kV Contact ESD Clamping Voltage www.onsemi.com 3 140 ESD7205 IEC61000-4-2 Waveform IEC 61000-4-2 Spec. Ipeak Level Test Voltage (kV) First Peak Current (A) Current at 30 ns (A) Current at 60 ns (A) 1 2 7.5 4 2 2 4 15 8 4 3 6 22.5 12 6 4 8 30 16 8 100% 90% I @ 30 ns I @ 60 ns 10% tP = 0.7 ns to 1 ns Figure 5. IEC61000-4-2 Spec Device ESD Gun Under Oscilloscope Test 50 W 50 W Cable Figure 6. Diagram of ESD Clamping Voltage Test Setup The following is taken from Application Note AND8308/D - Interpretation of Datasheet Parameters for ESD Devices. systems such as cell phones or laptop computers it is not clearly defined in the spec how to specify a clamping voltage at the device level. ON Semiconductor has developed a way to examine the entire voltage waveform across the ESD protection diode over the time domain of an ESD pulse in the form of an oscilloscope screenshot, which can be found on the datasheets for all ESD protection diodes. For more information on how ON Semiconductor creates these screenshots and how to interpret them please refer to AND8307/D. ESD Voltage Clamping For sensitive circuit elements it is important to limit the voltage that an IC will be exposed to during an ESD event to as low a voltage as possible. The ESD clamping voltage is the voltage drop across the ESD protection diode during an ESD event per the IEC61000-4-2 waveform. Since the IEC61000-4-2 was written as a pass/fail spec for larger www.onsemi.com 4 ESD7205 20 10 18 8 -14 12 6 10 6 -12 -10 8 4 6 4 2 4 -8 -6 -4 2 -2 2 NOTE: 8 -16 EQUIVALENT VIEC (kV) TLP CURRENT (A) TLP CURRENT (A) 16 EQUIVALENT VIEC (kV) -18 14 0 0 10 -20 2 4 6 8 10 12 14 16 18 0 0 0 20 2 4 6 8 10 12 14 16 VOLTAGE (V) VOLTAGE (V) Figure 7. Positive TLP IV Curve Figure 8. Negative TLP IV Curve 18 0 20 TLP parameter: Z0 = 50 W, tp = 100 ns, tr = 300 ps, averaging window: t1 = 30 ns to t2 = 60 ns. Transmission Line Pulse (TLP) Measurement L Transmission Line Pulse (TLP) provides current versus voltage (I-V) curves in which each data point is obtained from a 100 ns long rectangular pulse from a charged transmission line. A simplified schematic of a typical TLP system is shown in Figure 9. TLP I-V curves of ESD protection devices accurately demonstrate the product's ESD capability because the 10s of amps current levels and under 100 ns time scale match those of an ESD event. This is illustrated in Figure 10 where an 8 kV IEC 61000-4-2 current waveform is compared with TLP current pulses at 8 A and 16 A. A TLP I-V curve shows the voltage at which the device turns on as well as how well the device clamps voltage over a range of current levels. 50 W Coax Cable S Attenuator / 50 W Coax Cable 10 MW IM VM DUT VC Oscilloscope Figure 9. Simplified Schematic of a Typical TLP System Figure 10. Comparison Between 8 kV IEC 61000-4-2 and 8 A and 16 A TLP Waveforms www.onsemi.com 5 ESD7205 1 0.6 0 0.5 -1 CAPACITANCE (pF) -2 dB -3 -4 -5 -6 -7 -8 0.4 0.3 0.2 3.3 V 0V 0.1 -9 -10 1.E+06 1.E+07 1.E+08 1.E+09 1.E+10 0.0 0.E+00 FREQUENCY (Hz) 5.E+08 1.E+09 2.E+09 2.E+09 3.E+09 3.E+09 FREQUENCY Figure 11. RF Insertion Loss Figure 12. Capacitance over Frequency ORDERING INFORMATION Package Shipping ESD7205DT5G SOT-723 (Pb-Free) 8000 / Tape & Reel SZESD7205DT5G* SOT-723 (Pb-Free) 8000 / Tape & Reel ESD7205WTT1G SOT-323 (Pb-Free) 3000 / Tape & Reel SZESD7205WTT1G* SOT-323 (Pb-Free) 3000 / Tape & Reel Device For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *SZ Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC-Q100 Qualified and PPAP Capable. www.onsemi.com 6 ESD7205 PACKAGE DIMENSIONS SOT-723 CASE 631AA ISSUE D NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. -X- D b1 A -Y- 3 E 1 2X HE 2 2X e b C 0.08 X Y SIDE VIEW TOP VIEW 3X 1 3X DIM A b b1 C D E e HE L L2 L MILLIMETERS MIN NOM MAX 0.45 0.50 0.55 0.15 0.21 0.27 0.25 0.31 0.37 0.07 0.12 0.17 1.15 1.20 1.25 0.75 0.80 0.85 0.40 BSC 1.15 1.20 1.25 0.29 REF 0.15 0.20 0.25 RECOMMENDED SOLDERING FOOTPRINT* L2 BOTTOM VIEW 2X 0.40 2X 0.27 PACKAGE OUTLINE 1.50 3X 0.52 0.36 DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 7 ESD7205 PACKAGE DIMENSIONS SC-70 (SOT-323) CASE 419-04 ISSUE N D NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. e1 DIM A A1 A2 b c D E e e1 L HE 3 E HE 1 2 b e A 0.05 (0.002) MIN 0.80 0.00 0.30 0.10 1.80 1.15 1.20 0.20 2.00 MILLIMETERS NOM MAX 0.90 1.00 0.05 0.10 0.70 REF 0.35 0.40 0.18 0.25 2.10 2.20 1.24 1.35 1.30 1.40 0.65 BSC 0.38 0.56 2.10 2.40 MIN 0.032 0.000 0.012 0.004 0.071 0.045 0.047 0.008 0.079 INCHES NOM 0.035 0.002 0.028 REF 0.014 0.007 0.083 0.049 0.051 0.026 BSC 0.015 0.083 MAX 0.040 0.004 0.016 0.010 0.087 0.053 0.055 0.022 0.095 c A2 L A1 SOLDERING FOOTPRINT* 0.65 0.025 0.65 0.025 1.9 0.075 0.9 0.035 0.7 0.028 SCALE 10:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 www.onsemi.com 8 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative ESD7205/D