Monolithic Hall Effect ICs EM-series EM-1011 Shipped in packet-tape reel(5000pcs/Reel) EM-1011 is ultra-small Hall effect ICs of a single silicon chip composed of Hall element and a signal processing IC. Bipolar Hall Supply Voltage Effect Latch 3.518 Hall Element Continuous Excitation High Sensitivity Output Bop3mT Open Drain SMT Notice:It is requested to read and accept "IMPORTANT NOTICE" written on the back of the front cover of this catalogue. Operational Characteristics Vout H VoH S Marking 11 22 Bh 1VDD 2OUT 3PDN 4VSS N L VOL N-pole 0 Brp S-pole Bop Magnetic flux density Absolute Maximum RatingsTa=25 Symbol Limit Unit Supply Voltage VDD -0.3 25 V Output Current Isink 12 mA Output Supply Voltage Vout -0.3 25 V Operating Temperature Range Topr -30 115 Storage Temperature Range -40 125 Tstg 3VDD Regulator Magnetic and Electrical CharacteristicsTa=25 VDD=12V Item Symbol Conditions Min. Typ. Max. Unit 18 V Supply Voltage VDD 3.5 Operating Point BOP 0.5 3 6 mT Release Point Brp -6 -3 -0.5 mT Hysteresis Bh 1 6 12 mT 0.2 0.4 V 1 A 6 mA Output Saturation Voltage Vsat OUT="L"Isink=10mA Output Leakage Current Ileal OUT="H" Supply Current IDD OUT="H" 0.5 3 1mT=10Gauss 35 2OUT REG. Dynamic Offset Cancellation Item Functional Block Diagram Hall Element 1TEST Amplifier Schmitt Trigger Output Stage 4VSS EM-1011 *Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff. Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks, adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such applications is understood to be fully at the risk of the customer using our devices or systems. PackageUnit:mm) (For reference only)Land PatternUnit:mm) 0.50 00.1 0.90 0.3 Sensor center 5 1.90 5 3 4 0.1 0.55-0 0.3 0.25 0.1 5 5 Pin No. 1 2 3 4 Pin Name Function Comment TEST N.C TEST OUT Output Voltage VDD Supply Voltage VSS GND Note1) The sensor center is located within the 0.3mm circle. Note2) The tolerances of dimensions with no mentions is 0.1mm. Note3) Coplanarity:The differnces between standoff of terminals are max.0.1mm. Note4) The sensor part is located 0.4mm(typ.) far from marking surface. Output during start-up period BBop mT f 1.30 Application Circuit VOUT mT S-pole B 0 2:OUT 0 VDD3.5V V VDD 0 0 V V OUT 0 0 1:TEST N-pole Pull-up Resister BBop V c 1 2.10.2 1.250.1 2 0.25 2.10.1 1.3 0.3 VDD3.5V j EM-1011 4:VSS 3:VDD GND VDD Bypass Capacitor0.1F Temparature Dependence of Bop. Brp Supply Voltage 6 Operating PointmT Supply VoltageV 20 15 10 VDD12V 4 Bop 2 0 p -2 5 Brp q -4 0 -40 -20 0 20 40 60 80 Ambient Temperature 100 120 140 -6 -40 -20 0 20 40 60 80 100 120 140 Ambient Temperature 36 IMPORTANT NOTICE These products and their specifications are subject to change without notice. When you consider any use or application of these products, please make inquiries the sales office of Asahi Kasei Microdevices Corporation (AKM) or authorized distributors as to current status of the products. Descriptions of external circuits, application circuits, software and other related information contained in this document are provided only to illustrate the operation and application examples of the semiconductor products. You are fully responsible for the incorporation of these external circuits, application circuits, software and other related information in the design of your equipments. AKM assumes no responsibility for any losses incurred by you or third parties arising from the use of these information herein. AKM assumes no liability for infringement of any patent, intellectual property, or other rights in the application or use of such information contained herein. Any export of these products, or devices or systems containing them, may require an export license or other official approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange, or strategic materials. AKM products are neither intended nor authorized for use as critical componentsNote1) in any safety, life support, or other hazard related device or systemNote2), and AKM assumes no responsibility for such use, except for the use approved with the express written consent by Representative Director of AKM. As used here: Note1) A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability. Note2) A hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property. It is the responsibility of the buyer or distributor of AKM products, who distributes, disposes of, or otherwise places the product with a third party, to notify such third party in advance of the above content and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from any and all claims arising from the use of said product in the absence of such notification. April 4, 2012