145 Watts LPQ142 Series Total Power: 110-145 Watts Input Voltage: 85-264 VAC 120-300 VDC # of Outputs: Quad Electrical Specs Input Input range Frequency Inrush current Efficiency EMI filter Power factor Safety ground leakage current Special Features * Active power factor correction * IEC EN61000-3-2 compliance * Adjustable outputs on 1, 3 & 4 Remote sense on main output * Single wire current sharing * Power fail and remote inhibit * Built-in EMI filter * Low output ripple * Overvoltage protection * Overload protection * Thermal overload protection * Adjustable floating 4th output * Optional cover (-C suffix) * Optional fan cover (-CF suffix) Environmental Operating temperature: 0 to 50C ambient derate each output at 2.5% per degree from 85-264 VAC, 120-300 VDC 47-63 Hz 38 A max, cold start @ 25C 75% typical at full load Meets FCC Class B conducted CISPR 22 Class B conducted EN55022 Class B conducted VDE 0878 PT3 Class B conducted 0.99 typical 1.0 mA @ 50/60 Hz, 264 VAC input Output Maximum power Adjustment range Hold-up time Overload protection Overvoltage protection 80 W convection (60 W with cover-C) 145 W with 30 CFM forced air (100 W with cover-C) 3.3 - 5.5V on main; -12 - 15V on 3rd output 3.3 - 25 V on 4th output 20 ms @145 W load at nominal line Short circuit protection on all outputs. Case overload protected @ 110-145% above peak rating Tracks outputs 1, 3 & 4; 10 to 35% Logic Control AC Power failure Remote inhibit Remote sense DC-OK 50 to 70C TTL logic signal goes high 100 - 500 msec after V1 output; It goes low at least 4 msec before loss of regulation TTL High disables output. Contact closure causes outputs to "bounce" Compensates for 0.5 V lead drop min. Will operate without remote sense connected. Reverse connection protected. TTL logic signal goes high after main output is in regulation. It goes low when there is a loss of regulation Electromagnetic susceptibility: designed to meet EN61000-4, -2, -3, -4, -5, -6, -8, -11, Level 3 Humidity: Operating; non-condensing Safety 5% to 95% Vibration: Three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four major resonances 0.75 G peak 5 Hz to 500 Hz, operational Storage temperature: -40 to 85C Temperature coefficient: .04% per C MTBF demonstrated: >550,000 hours at full load and 25C ambient conditions 110 VDE UL CB CSA CE NEMKO 60950 60950 Certificate and report 60950 Mark (LVD) EN 60950/EMKO-TUE Technical Support: (888) 41-ASTEC or (407) 241-2752 Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662 rev 08.24.04 AMERICAS EUROPE ASIA 5810 Van Allen Way Carlsbad, CA 92008 Telephone: 760-930-4600 Facsimile: 760-930-0698 Astec House, Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX, UK Telephone: 44 (1384) 842-211 Facsimile: 44 (1384) 843-355 Units 2111-2116, Level 21 Tower1, Metroplaza 223, Hing Fong Road Fwai Fong, New Territories Hong Kong Telephone: 852-2437-9662 Facsimile: 852-2402-4426 LPQ142 Series Ordering Information Model Number Output Voltage Minimum Load Maximum Load with Convection Cooling Maximum Load with 30 CFM Forced Air Peak Load Regulation2 Ripple P/P(PARD)3 LPQ142 5 V (3.3 - 5.5 V) 12 V -12 V (-12 -15 V) 3.3-25 V 0A 0A 0A 0.5 A 12 A 5A 1A 1.5 A 25 A 6A 1.5 A 4.5 A 27 A 9A 2A 5A 2% 3% 3% 3% 50 mV 120 mV <1% <50mV or 1% 1. Peak current lasting <30 seconds with a maximum 10% duty cycle. 2. At 25C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3. Peak-to-peak with 20 MHz bandwidth and 10 F in parallel with a 0.1 F capacitor at rated line voltage and load ranges. 4. 4th output adjustable 3.3-25 V factory set at 5 V. 5. *Minimum loads are required when output set below 5 Volts 6. Remote inhibit resets OVP latch Note: -C suffix added to the model number indicates cover option. -CF suffix added to the model number indicates fan cover option. Pin Assignments Connector LPQ142 SK1 PIN 1 PIN 3 PIN 5 GROUND NEUTRAL LINE SK2 PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 +12 V COMMON -12 V COMMON +5 V to +25 V (Float) COMMON (Float) TB-1 TB-2 COMMON +5 V SK4 MAIN OUTPUT 6 V4V4+ COMM -12V OUT COMM +12V OUT SK2 L 1 N 5 GND PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 PIN 7 PIN 8 PIN 9 PIN 10 Mating Connectors (SK1) AC Input: N/C DC OK N/C V1 SWP Common +V1 sense Sense common + inhibit - inhibit Power fail 6 1 SK6 -CF option M3 #6-32 (3X) 19.1 29.1 SK6 10 SK1 1.5 (38.1) M3 (2X) 6.4 161.5 171.5 #6-32 4.00 (101.6) (4X) 63.5 Molex 09-50-8051 (USA) Molex 09-91-0500 (UK) PINS: 08-58-0111 (SK2) Aux DC Output: Molex 09-50-8061 (USA) Molex 09-91-0600 (UK) PINS: 08-58-0111 (SK6) Control Signals: Molex 90142-0010 (USA) PINS: 90119-2110 or Amp: 87977-3 PINS: 87309-8 (SK4) Main output: Molex BB-124-08 Astec connector kit #70-841-017, includes al of the above. (2X) 119.6 (2X) 139.7 7.0 (177.8) M3 (8 places) #6-32 (8 places) Notes: 1. Specifications subject to change without notice. 2. All dimensions in inches (mm), tolerance is 0.02". 3. Specifications are for convection rating at factory settings unless otherwise stated. 4. Mounting screw maximum insertion depth is 0.12". 5. Warranty: 1 year 6. Weight: 1.63 lb / 0.74 kg www.astecpower.com 111