TYPE PRODUCT SPECIFICATION NUMBER BUS-12-023
TITLE PAGE REVISION
Mini-Jump – Gold or GXT Plated 1 of 17 FED
AUTHORIZED BY DATE
H.
SUNDYS.FierroJ.ZH
OU
4-14- APR
0506/12/065/1
5/2012
CLASSIFICATION
CONFIDENTIALUNRESTRICTED
This docum ent is the property of and em bodies CON FIDENTIA L and PROPRIE T A R Y informati on of FCI.FCI Electronics. No part of the information shown on this document may be used
in any way withou t the written consent of FCI .Electronics.
Form E-3005
Rev B 07/30/04A 02/12/01
V04-078220603
GS-01-001
Copyright FCI
Form E-3334
Rev E
GS-01-001
1.0 GENERAL
Scope - This specification covers gold or gold flash over palladium alloy plated mini-jump connectors
designed for low power interconnection of two adjacent 0.025 inch square pins, free standing or in headers,
on 0.100 or 0.150 inch centers. This product meets the requirements of the European Union Directive of
Restrictions for Hazardous Substances (Directive 2002/95/EC). This specification is composed of the
following sections.
Paragraph Title Page
1.0 GENERAL 1
2.0 APPLICABLE DOCUMENTS 1
3.0 REQUIREMENTS 2
3.1 Qualification 2
3.2 Material 2
3.3 Finish 2
3.4 Design and Construction 3
3.5 Electrical Characteristics 3
3.6 Mechanical Characteristics 6
3.7 Environmental Conditions 7
4.0 QUALITY ASSURANCE PROVISIONS 11
4.1 Equipment Calibration 11
4.2 Inspection Conditions 12
4.3 Qualification Inspections 12
4.4 Requalification Testing 13
5.0 NOTES AND DEFINITIONS 16
2.0 APPLICABLE DOCUMENTS
The following documents, of the issue in effect on the date of the latest revision of this specification, shall
form a part of this specification to the extent specified herein.
Military Specifications
MIL-M-24519 Molding Plastics, Polyester, Thermoplastics
MIL-G-45204 Gold Plating, Electrodeposited
MIL-P-45209 Palladium Plating, Electrodeposited
MIL-C-45662 Calibration System Requirements
MIL-P-55110 Printed Wiring Boards
MIL-STD-105 Sampling Procedures and Tables for Inspection by Attributes
MIL-STD-202 Test Methods for Electronic and Electrical Component Parts
MIL-STD-275 Printed Wiring for Electronic Equipment
MIL-STD-1344 Test Methods for Electrical Connectors
Formatted: French (France)
Formatted: Tab stops: 1.65", Left + Not at
1.58"
Formatted: Indent: Left: 0.42", Tab stops:
2.42", Left + 4.25", Left + 6.5", Left + Not at
2" + 2.5" + 4.17" + 6.58"
PDS: Rev :F STATUS:Released Printed: May 16, 2012
TYPE PRODUCT SPECIFICATION NUMBER BUS-12-023
TITLE PAGE REVISION
Mini-Jump – Gold or GXT Plated 2 of 17 FED
AUTHORIZED BY DATE
H.
SUNDYS.FierroJ.ZH
OU
4-14- APR
0506/12/065/1
5/2012
CLASSIFICATION
CONFIDENTIALUNRESTRICTED
This docum ent is the property of and em bodies CON FIDENTIA L and PROPRIE T A R Y informati on of FCI.FCI Electronics. No part of the information shown on this document may be used
in any way withou t the written consent of FCI .Electronics.
Form E-3005
Rev B 07/30/04A 02/12/01
V04-078220603
GS-01-001
Copyright FCI
Form E-3334
Rev E
GS-01-001
Federal Specifications
QQ-N-290 Nickel Plating (Electrodeposited)
QQ-B-613 Brass, Leaded and Non-Leaded
Industry Specifications/Standards
ASTM B-194 Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar
UL-94 Tests for Flammability of Plastic Materials
3.0 REQUIREMENTS
3.1 Qualification
Connectors furnished under this specification shall be products capable of meeting the qualification
test requirements specified herein. New products of the same type shall be considered qualified by
similarity pending actual testing.
3.2 Material
The material for each part shall be as specified herein, or equivalent. Substitute material shall meet
the performance requirements of this specification.
3.2.1 Metallic Parts
3.2.1.1 Contact Body. The body shall be Brass alloy UNS
C26000 in accordance with QQ-B-613.
3.2.1.2 Contact Spring. The spring shall be Beryllium
Copper alloy UNS C17200 in accordance with ASTM B-194. After
stamping, the spring shall be heat-treated to a full hard condition.
3.2.2 Insulator Housing. The housing material shall be unfilled Polyester in accordance with
MIL-M-24519. The material shall be rated flame retardant 94 V-O in accordance with UL-
94.
3.3 Finish
3.3.1 Contact Body. The body shall be plated in the contact area with 40 microinches
(minimum) gold per MIL-C-45204 or a thin gold flash over 37 microinches (minimum)
palladium alloy per MIL-P-45209, Type II, Grade C over 50 microinches (minimum) nickel
per QQ-N-290, Class 2.
PDS: Rev :F STATUS:Released Printed: May 16, 2012
TYPE PRODUCT SPECIFICATION NUMBER BUS-12-023
TITLE PAGE REVISION
Mini-Jump – Gold or GXT Plated 3 of 17 FED
AUTHORIZED BY DATE
H.
SUNDYS.FierroJ.ZH
OU
4-14- APR
0506/12/065/1
5/2012
CLASSIFICATION
CONFIDENTIALUNRESTRICTED
This docum ent is the property of and em bodies CON FIDENTIA L and PROPRIE T A R Y informati on of FCI.FCI Electronics. No part of the information shown on this document may be used
in any way withou t the written consent of FCI .Electronics.
Form E-3005
Rev B 07/30/04A 02/12/01
V04-078220603
GS-01-001
Copyright FCI
Form E-3334
Rev E
GS-01-001
3.3.2 Contact Spring. The spring shall be plated on the mating side with 3 microinches
(minimum) gold per MIL-G-45204, Type II, Grade C.
3.4 Design and Construction
The connector typically shall be a two piece assembly comprising two interconnected contacts
retained in a plastic housing. The female (disconnect) end of the contact shall interface with 0.025
inch square (or round) pins on 0.100 or 0.150 inch centers, as appropriate. In certain applications,
the connector shall consist of the contacts without a housing.
3.4.1 Mating. The connector shall be capable of being mated or unmated by hand without the
use of special tools within the specified temperature range.
3.4.2 Workmanship. Connectors shall be uniform in quality and shall be free from burrs,
scratches, cracks, voids, chips, blisters, pin holes, sharp edges, and other defects that
will adversely affect life or serviceability.
3.4.3 Interchangeability. The connector shall be capable of mating with any appropriately
constituted male connector of the same population without degradation in performance.
3.5 Electrical Characteristics
3.5.1 Current Rating. The maximum current rating of the connector shall be 3.0 amperes DC
(2.5 amperes for multi-position assembly).
3.5.2 Contact Resistance. (see 5.1) The contact resistance shall not exceed the value
specified in Table 1, when measured in accordance with MIL-STD-202, Method 307. The
following details shall apply:
(a) Method of Connection - Attach current and voltage leads as shown in Figure 1.
(b) Test Current - 1 ampere DC
PDS: Rev :F STATUS:Released Printed: May 16, 2012
TYPE PRODUCT SPECIFICATION NUMBER BUS-12-023
TITLE PAGE REVISION
Mini-Jump – Gold or GXT Plated 4 of 17 FED
AUTHORIZED BY DATE
H.
SUNDYS.FierroJ.ZH
OU
4-14- APR
0506/12/065/1
5/2012
CLASSIFICATION
CONFIDENTIALUNRESTRICTED
This docum ent is the property of and em bodies CON FIDENTIA L and PROPRIE T A R Y informati on of FCI.FCI Electronics. No part of the information shown on this document may be used
in any way withou t the written consent of FCI .Electronics.
Form E-3005
Rev B 07/30/04A 02/12/01
V04-078220603
GS-01-001
Copyright FCI
Form E-3334
Rev E
GS-01-001
FIGURE 1 - CONTACT RESISTANCE
PDS: Rev :F STATUS:Released Printed: May 16, 2012
TYPE PRODUCT SPECIFICATION NUMBER BUS-12-023
TITLE PAGE REVISION
Mini-Jump – Gold or GXT Plated 5 of 17 FED
AUTHORIZED BY DATE
H.
SUNDYS.FierroJ.ZH
OU
4-14- APR
0506/12/065/1
5/2012
CLASSIFICATION
CONFIDENTIALUNRESTRICTED
This docum ent is the property of and em bodies CON FIDENTIA L and PROPRIE T A R Y informati on of FCI.FCI Electronics. No part of the information shown on this document may be used
in any way withou t the written consent of FCI .Electronics.
Form E-3005
Rev B 07/30/04A 02/12/01
V04-078220603
GS-01-001
Copyright FCI
Form E-3334
Rev E
GS-01-001
TABLE 1 - CONTACT RESISTANCE
Connector Maximum Resistance - Milliohms
Spacing Initial After Test
0.100 11 15
0.150 13 20
3.5.3 Low Level Circuit Resistance. (see 5.1) The low level circuit (contact) resistance shall
not exceed the value specified in Table 1, when measured in accordance with MIL-STD-
1344, Method 3002. The following details shall apply:
(a) Method of Connection - See Figure 1
(b) Test Current - 1 milliampere DC
(c) Maximum Open Circuit Voltage - 20 millivolts DC
3.5.4 Capacitance. (see 5.3) The capacitance between adjacent positions of the unmated
connector shall not exceed 2.0 pf, when measured in accordance with MIL-STD-202,
Method 305. The following details shall apply:
(a) Points of Measurement - Between adjacent contact positions
(b) Test Frequency - 1 megahertz
3.5.5 Insulation Resistance. (see 5.3) The insulation resistance between adjacent positions of
the unmated connector shall be not less than 50,000 megohms (20,000 megohms after
exposure to the humidity environment specified in paragraph 3.7.2), when tested in
accordance with MIL-STD-202, Method 302. The following details shall apply:
(a) Points of Measurement - Between adjacent contact positions
(b) Test Potential - B (500 volts)
(c) Time of Application - 60 seconds
3.5.6 Dielectric Withstanding Voltage. (see 5.3) There shall be no evidence of insulation
breakdown, arc-over, or excessive (>1 milliampere) leakage current when the unmated
connector is tested in accordance with MIL-STD-202, Method 301. The following details
shall apply:
(a) Test Potential – 1000 volts RMS, 60 Hz at sea-level
(b) Test Duration - 60 seconds
(c) Points of Measurement - Between adjacent contact positions
PDS: Rev :F STATUS:Released Printed: May 16, 2012
TYPE PRODUCT SPECIFICATION NUMBER BUS-12-023
TITLE PAGE REVISION
Mini-Jump – Gold or GXT Plated 6 of 17 FED
AUTHORIZED BY DATE
H.
SUNDYS.FierroJ.ZH
OU
4-14- APR
0506/12/065/1
5/2012
CLASSIFICATION
CONFIDENTIALUNRESTRICTED
This docum ent is the property of and em bodies CON FIDENTIA L and PROPRIE T A R Y informati on of FCI.FCI Electronics. No part of the information shown on this document may be used
in any way withou t the written consent of FCI .Electronics.
Form E-3005
Rev B 07/30/04A 02/12/01
V04-078220603
GS-01-001
Copyright FCI
Form E-3334
Rev E
GS-01-001
3.6 Mechanical Characteristics
3.6.1 Contact Retention. (see 5.2) The contact pair shall not be dislodged from the housing
when an axial force of 4 pounds (2 pounds per terminal) is applied in the direction
opposite from that of insertion. The force shall be applied at a crosshead speed of 1 inch
per minute and the maximum load shall be maintained for 10 seconds.
3.6.2 Total Mating Force. The total force to mate the connector with an appropriate header
having properly configured (see Figure 2) 0.025 inch square pins shall not exceed the
value shown in Table II for the appropriate contact spring thickness.
TABLE II - FORCE VS. SPRING THICKNESS
Spring Thickness Individual Contact Force-Grams Total Force
(MILS) Insert (Max) Withdraw (Min) (Grams Max)
3.5 300 40 600
4.8 450 50 900*
* Multiply by number of positions for multi-position assembly.
3.6.3 Individual Contact Insertion Force. When measured using a maximum gage configured
as shown in Figure 3, the individual contact insertion force shall not exceed the value
shown in Table II for the contact spring thickness used in the terminal.
3.6.4 Individual Contact Withdrawal Force. After three insertions of a maximum gage, the force
required to withdraw a minimum gage, configured as shown in figure 3, shall be not less
than the value shown in Table II for the contact spring thickness used in the terminal.
3.6.5 Durability. After the number of mating cycles specified in Table III, the individual contact
withdrawal force shall be not less than the value shown in Table II (see 3.6.4) and the
contact resistance shall not exceed the value specified in Table I (see 3.5.2).
TABLE III - DURABILITY
Spring Thickness
(MILS) Mating Cycles
3.5 100
4.8 50
PDS: Rev :F STATUS:Released Printed: May 16, 2012
TYPE PRODUCT SPECIFICATION NUMBER BUS-12-023
TITLE PAGE REVISION
Mini-Jump – Gold or GXT Plated 7 of 17 FED
AUTHORIZED BY DATE
H.
SUNDYS.FierroJ.ZH
OU
4-14- APR
0506/12/065/1
5/2012
CLASSIFICATION
CONFIDENTIALUNRESTRICTED
This docum ent is the property of and em bodies CON FIDENTIA L and PROPRIE T A R Y informati on of FCI.FCI Electronics. No part of the information shown on this document may be used
in any way withou t the written consent of FCI .Electronics.
Form E-3005
Rev B 07/30/04A 02/12/01
V04-078220603
GS-01-001
Copyright FCI
Form E-3334
Rev E
GS-01-001
3.7 Environmental Conditions
3.7.1 Thermal Shock. After exposure of the mated connector to alternate periods of extreme
high and low temperature, there shall be no evidence of cracking or crazing of the
insulator housing or other physical damage to the connector; the dielectric withstanding
voltage of the unmated connector shall be not less than 1000 volts RMS (see 3.5.6). The
test shall be in accordance with MIL-STD-202, Method 107. The following details and
exceptions shall apply:
(a) Test Condition - A (5, 1-hour cycles)
(b) Temperature Range - +120oC to -55oC
(c) Exposure time at each temperature - 30 minutes, minimum
(d) Transfer time - 30 seconds maximum
3.7.2 Humidity. After exposure of the mated connector to a high humidity environment, the
contact resistance shall not exceed the value specified in Table I (see 3.5.2). The
insulation resistance of the unmated connector shall be not less than 20,000 megohms
(see paragraph 3.5.5). The test shall be in accordance with MIL-STD-202, Method 106
(excluding steps 7a and 7b). The following details shall apply:
(a) Test Duration - 10 days (240 hours)
3.7.3 High Temperature Life. After exposure of the mated connector to a high temperature
operating environment, the contact resistance shall not exceed the value specified in
Table I (see 3.5.2). The insulation resistance of the unmated connector shall be not less
than 50,000 megohms (see 3.5.5). The test shall be in accordance with MIL-STD-202,
Method 108. The following details shall apply:
(a) Chamber Temperature - Adjusted to achieve +120oC temperature of contact
under load.
(b) Test Condition - B (250 hours)
(c) Operating Conditions - Rated current (see 3.5.1) through both contacts; duty cycle:
45 minutes ON and 15 minutes OFF.
PDS: Rev :F STATUS:Released Printed: May 16, 2012
TYPE PRODUCT SPECIFICATION NUMBER BUS-12-023
TITLE PAGE REVISION
Mini-Jump – Gold or GXT Plated 8 of 17 FED
AUTHORIZED BY DATE
H.
SUNDYS.FierroJ.ZH
OU
4-14- APR
0506/12/065/1
5/2012
CLASSIFICATION
CONFIDENTIALUNRESTRICTED
This docum ent is the property of and em bodies CON FIDENTIA L and PROPRIE T A R Y informati on of FCI.FCI Electronics. No part of the information shown on this document may be used
in any way withou t the written consent of FCI .Electronics.
Form E-3005
Rev B 07/30/04A 02/12/01
V04-078220603
GS-01-001
Copyright FCI
Form E-3334
Rev E
GS-01-001
FIGURE 2 - MATING HEADER
PDS: Rev :F STATUS:Released Printed: May 16, 2012
TYPE PRODUCT SPECIFICATION NUMBER BUS-12-023
TITLE PAGE REVISION
Mini-Jump – Gold or GXT Plated 9 of 17 FED
AUTHORIZED BY DATE
H.
SUNDYS.FierroJ.ZH
OU
4-14- APR
0506/12/065/1
5/2012
CLASSIFICATION
CONFIDENTIALUNRESTRICTED
This docum ent is the property of and em bodies CON FIDENTIA L and PROPRIE T A R Y informati on of FCI.FCI Electronics. No part of the information shown on this document may be used
in any way withou t the written consent of FCI .Electronics.
Form E-3005
Rev B 07/30/04A 02/12/01
V04-078220603
GS-01-001
Copyright FCI
Form E-3334
Rev E
GS-01-001
FIGURE 3 - INSERTION/WITHDRAWAL FORCE GAGE
PDS: Rev :F STATUS:Released Printed: May 16, 2012
TYPE PRODUCT SPECIFICATION NUMBER BUS-12-023
TITLE PAGE REVISION
Mini-Jump – Gold or GXT Plated 10 of 17 FED
AUTHORIZED BY DATE
H.
SUNDYS.FierroJ.ZH
OU
4-14- APR
0506/12/065/1
5/2012
CLASSIFICATION
CONFIDENTIALUNRESTRICTED
This docum ent is the property of and em bodies CON FIDENTIA L and PROPRIE T A R Y informati on of FCI.FCI Electronics. No part of the information shown on this document may be used
in any way withou t the written consent of FCI .Electronics.
Form E-3005
Rev B 07/30/04A 02/12/01
V04-078220603
GS-01-001
Copyright FCI
Form E-3334
Rev E
GS-01-001
FIGURE 4 - MOUNTING FOR STOCK/VIBRATION
PDS: Rev :F STATUS:Released Printed: May 16, 2012
TYPE PRODUCT SPECIFICATION NUMBER BUS-12-023
TITLE PAGE REVISION
Mini-Jump – Gold or GXT Plated 11 of 17 FED
AUTHORIZED BY DATE
H.
SUNDYS.FierroJ.ZH
OU
4-14- APR
0506/12/065/1
5/2012
CLASSIFICATION
CONFIDENTIALUNRESTRICTED
This docum ent is the property of and em bodies CON FIDENTIA L and PROPRIE T A R Y informati on of FCI.FCI Electronics. No part of the information shown on this document may be used
in any way withou t the written consent of FCI .Electronics.
Form E-3005
Rev B 07/30/04A 02/12/01
V04-078220603
GS-01-001
Copyright FCI
Form E-3334
Rev E
GS-01-001
3.7.4 Shock. There shall be no evidence of physical or mechanical damage when the mated
connector is subjected to transient accelerations. During and after each shock, the
contacts shall evidence no discontinuity greater than 1 microsecond. The test shall be in
accordance with MIL-STD-202, Method 213. The following details shall apply:
(a) Test Condition - 1 (100G, 6 ms sawtooth).
(b) Number of Shocks - 3 shocks in each direction along three orthogonal axes (18
total).
(c) Mounting - See Figure 4
(d) Restraining Method - None
3.7.5 Vibration. There shall be no evidence of physical or mechanical damage when the mated
connector is subjected to prolonged mechanical vibration; and the individual contact
withdrawal force shall be not less than the value specified in Table II (see 3.6.4). During
the vibration along each axis, the contacts shall evidence no discontinuity greater than 1
microsecond. At the completion of the test, the contact resistance shall not exceed the
value specified in Table I (see 3.5.2). The test shall be in accordance with MIL-STD-202,
Method 204. The following details shall apply:
(a) Test Condition - B (+_ 15G, 10 to 2000 Hz)
(b) Test Duration - 4 hours along each of three orthogonal axes (12 hours total)
(c) Mounting - see Figure 4
(d) Restraining Method - None
3.7.6 Hydrogen Sulfide (H2S) Atmosphere. After exposure of the mated connector to moist
contaminated environment, the low level circuit resistance shall not exceed the value
specified in Table I (see 3.5.3). The following details shall apply:
(a) Test Medium - 3 ppm H2S in air
(b) Test Temperature - +40oC
(c) Test Duration - 48 hours
3.7.7 Salt Spray. After exposure of the mated connector to a salt fog atmosphere, the low level
circuit resistance shall not exceed the value specified in Table I (see 3.5.3). The test
shall be in accordance with MIL-STD-202, Method 101. The following details shall apply:
(a) Salt Solution - 5 percent by weight
(b) Test Condition - B (48 hours)
PDS: Rev :F STATUS:Released Printed: May 16, 2012
TYPE PRODUCT SPECIFICATION NUMBER BUS-12-023
TITLE PAGE REVISION
Mini-Jump – Gold or GXT Plated 12 of 17 FED
AUTHORIZED BY DATE
H.
SUNDYS.FierroJ.ZH
OU
4-14- APR
0506/12/065/1
5/2012
CLASSIFICATION
CONFIDENTIALUNRESTRICTED
This docum ent is the property of and em bodies CON FIDENTIA L and PROPRIE T A R Y informati on of FCI.FCI Electronics. No part of the information shown on this document may be used
in any way withou t the written consent of FCI .Electronics.
Form E-3005
Rev B 07/30/04A 02/12/01
V04-078220603
GS-01-001
Copyright FCI
Form E-3334
Rev E
GS-01-001
4.0 QUALITY ASSURANCE
4.1 Equipment Calibration
All test equipment and facilities used in the performance of any test shall be maintained in a
calibration system in accordance with MIL-C-45662.
4.2 Inspection Conditions
Unless otherwise specified herein, all inspections shall be performed under the following ambient
conditions:
(a) Temperature - 25oC + 5oC
(b) Relative Humidity - 30% to 80%
(c) Barometric Pressure - Local ambient
4.3 Qualification Inspection
Qualification inspection shall be performed on sample units produced with equipment normally used
in production.
4.3.1 Sample. Qualification Inspection shall be performed on five (5) groups of connectors;
each group shall comprise five (5) connectors of each type for which qualification under
this specification is desired. For multi-position connectors, a sixth sample (one
connector) shall be required for Group 3 tests.
4.3.2 Preparation of Samples
4.3.2.1 Printed Wiring Test Boards - Five (5) test boards conforming to the
applicable requirements of MIL-P-55110 and MIL-STD-275 shall be
prepared as shown in Figure 5.
4.3.2.2 Mating Headers - Five (5) mating headers of the appropriate population
and configuration and conforming to the requirements of Figure 2 shall be
prepared.
4.3.2.3 Header Mounting - The headers shall be installed on, and hand soldered
to, the test boards; an appropriately active flux shall be used to ensure that
the connection does not contribute any degradation.
PDS: Rev :F STATUS:Released Printed: May 16, 2012
TYPE PRODUCT SPECIFICATION NUMBER BUS-12-023
TITLE PAGE REVISION
Mini-Jump – Gold or GXT Plated 13 of 17 FED
AUTHORIZED BY DATE
H.
SUNDYS.FierroJ.ZH
OU
4-14- APR
0506/12/065/1
5/2012
CLASSIFICATION
CONFIDENTIALUNRESTRICTED
This docum ent is the property of and em bodies CON FIDENTIA L and PROPRIE T A R Y informati on of FCI.FCI Electronics. No part of the information shown on this document may be used
in any way withou t the written consent of FCI .Electronics.
Form E-3005
Rev B 07/30/04A 02/12/01
V04-078220603
GS-01-001
Copyright FCI
Form E-3334
Rev E
GS-01-001
4.3.2.4 Sample Configuration - When mated with the headers, the connectors
shall form a series connected circuit.
4.3.3 Test Sequence. The connectors shall be subjected to the inspections specified in Table
IV, in the order shown.
4.4 Requalification Testing
If either of the following conditions occur, the product responsible engineer shall initiate
requalification testing.
4.4.1 A significant design change is made to an existing product previously qualified under this
specification. A significant design change shall be defined to include, but not be limited
to, changes in contact material composition, contact material thickness, contact force,
contact surface geometry, underlying material composition, underlying material thickness,
insulator design, contact base material, or contact lubrication requirements.
4.4.2 A product failure occurs during production or end use requiring corrective action to be
taken relative to the product design or manufacturing process.
Requalification testing shall consist of all or applicable parts of the Qualification Test Matrix as
determined by development/product, quality, test, and reliability engineering.
PDS: Rev :F STATUS:Released Printed: May 16, 2012
TYPE PRODUCT SPECIFICATION NUMBER BUS-12-023
TITLE PAGE REVISION
Mini-Jump – Gold or GXT Plated 14 of 17 FED
AUTHORIZED BY DATE
H.
SUNDYS.FierroJ.ZH
OU
4-14- APR
0506/12/065/1
5/2012
CLASSIFICATION
CONFIDENTIALUNRESTRICTED
This docum ent is the property of and em bodies CON FIDENTIA L and PROPRIE T A R Y informati on of FCI.FCI Electronics. No part of the information shown on this document may be used
in any way withou t the written consent of FCI .Electronics.
Form E-3005
Rev B 07/30/04A 02/12/01
V04-078220603
GS-01-001
Copyright FCI
Form E-3334
Rev E
GS-01-001
FIGURE 5
PDS: Rev :F STATUS:Released Printed: May 16, 2012
TYPE PRODUCT SPECIFICATION NUMBER BUS-12-023
TITLE PAGE REVISION
Mini-Jump – Gold or GXT Plated 15 of 17 FED
AUTHORIZED BY DATE
H.
SUNDYS.FierroJ.ZH
OU
4-14- APR
0506/12/065/1
5/2012
CLASSIFICATION
CONFIDENTIALUNRESTRICTED
This docum ent is the property of and em bodies CON FIDENTIA L and PROPRIE T A R Y informati on of FCI.FCI Electronics. No part of the information shown on this document may be used
in any way withou t the written consent of FCI .Electronics.
Form E-3005
Rev B 07/30/04A 02/12/01
V04-078220603
GS-01-001
Copyright FCI
Form E-3334
Rev E
GS-01-001
TABLE IV - QUALIFICATION INSPECTION
Sample Group
Examination or Test Paragraph 1 2 3 4 5 6
Total Mating Force 3.6.2 - - - x x x
Individual Contact Withdrawal Force 3.6.4 - - - x x x
Contact Resistance 3.5.2 x x - x x x
Capacitance 3.5.4 - - x - - -
Insulation Resistance 3.5.5 - - x - - -
Dielectric Withstanding Voltage 3.5.6 - - x - - -
Contact Retention 3.6.1 x x - x x x
Thermal Shock 3.7.1 x x x - - -
Dielectric Withstanding Voltage 3.5.6 - - x - - -
Humidity 3.7.2 x x x - - -
Contact Resistance 3.5.2 x x - - - -
Insulation Resistance 3.5.5 - - x - - -
High Temperature Life 3.7.3 x - x - - -
Contact Resistance 3.5.2 x x - - - -
Insulation Resistance 3.5.5 - - x - - -
Shock 3.7.4 - - - x x -
Vibration 3.7.5 - - - x x -
Contact Resistance 3.5.2 - - - x x -
Individual Contact 3.6.4 - - - x x -
Durability 3.6.5 - - - x - x
Contact Resistance 3.5.2 - - - x - x
Individual Contact Withdrawal Force 3.6.4 - - - x - x
Hydrogen Sulfide Atmosphere 3.7.6 - - - x x x
Low Level Circuit Resistance 3.5.3 - - - x x x
Salt Spray 3.7.7 - - - x x x
Low Level Circuit Resistance 3.5.3 - - - x x x
Contact Retention 3.6.1 x - - x - -
PDS: Rev :F STATUS:Released Printed: May 16, 2012
TYPE PRODUCT SPECIFICATION NUMBER BUS-12-023
TITLE PAGE REVISION
Mini-Jump – Gold or GXT Plated 16 of 17 FED
AUTHORIZED BY DATE
H.
SUNDYS.FierroJ.ZH
OU
4-14- APR
0506/12/065/1
5/2012
CLASSIFICATION
CONFIDENTIALUNRESTRICTED
This docum ent is the property of and em bodies CON FIDENTIA L and PROPRIE T A R Y informati on of FCI.FCI Electronics. No part of the information shown on this document may be used
in any way withou t the written consent of FCI .Electronics.
Form E-3005
Rev B 07/30/04A 02/12/01
V04-078220603
GS-01-001
Copyright FCI
Form E-3334
Rev E
GS-01-001
5.0 NOTES AND DEFINITIONS
5.1 Contact Resistance
Differences in contact resistance between various terminal configurations represent changes in bulk
resistance due to longer lengths of current path.
5.2 Contact Retention
Only terminals employing an integral latching mechanism (e.g. barbs, dimples, etc.) for rigid
retention within the housing are subject to this requirement. Terminals which "free-float" within a
housing and are retained by the closure of some form of hinged cover are not included.
5.3 Multi-Position Connector
Assemblies containing more than one jumper shall be subjected to the Group 3 tests; these tests do
not apply to single position devices.
Formatted: French (France)
PDS: Rev :F STATUS:Released Printed: May 16, 2012
TYPE PRODUCT SPECIFICATION NUMBER BUS-12-023
TITLE PAGE REVISION
Mini-Jump – Gold or GXT Plated 17 of 17 FED
AUTHORIZED BY DATE
H.
SUNDYS.FierroJ.ZH
OU
4-14- APR
0506/12/065/1
5/2012
CLASSIFICATION
CONFIDENTIALUNRESTRICTED
This docum ent is the property of and em bodies CON FIDENTIA L and PROPRIE T A R Y informati on of FCI.FCI Electronics. No part of the information shown on this document may be used
in any way withou t the written consent of FCI .Electronics.
Form E-3005
Rev B 07/30/04A 02/12/01
V04-078220603
GS-01-001
Copyright FCI
Form E-3334
Rev E
GS-01-001
REVISION RECORD
REV PAGE DESCRIPTION EC # DATE
A 1 Change the Au plating of the spring to 3u" 10071 11/11/83
B 15 Replaced section 4.4 and subsections; V10413 02/27/91
17 Deleted Table V - Quality Inspection;
18 Deleted Table VI - Acceptance Inspection
C All Revised format to be consistent with V01904 07/28/00
GS-01-001, and change BERG, Dupont,
etc. references to FCI.
D All Revised the Format and changed section 3.5.6 V05-0355 04-15-05
and 3.71 to 1000 Vrms.
E 1 Add lead free information M06-0228 06/12/06
F 1,2 Change plating from Au to Au or gold flash over ELX-N-011638 05/15/12
palladium alloy The following constitutes the recommended order and paragraph
numbering scheme in compliance with GS-01-001. Paragraphs that are not needed shall be eliminated, and
subsequent paragraphs renumbered.
Please delete this note after reading.
OBJECTIVE
SCOPE
GENERAL
DEFINITIONS
PROCEDURE
REFERENCE DOCUMENTS (If Applicable)
Formatted: Bullets and Numbering
Formatted: Bullets and Numbering
Formatted: Indent: First line: 11 ch
Formatted: Indent: First line: 11 ch
Formatted: Indent: Left: 0", First line: 11 ch
Formatted: Bullets and Numbering
Formatted: Indent: First line: 11 ch
Formatted: Indent: Left: 0", First line: 11 ch
Formatted: Bullets and Numbering
Formatted: Indent: First line: 11 ch
Formatted: Indent: Left: 0", First line: 11 ch
Formatted: Bullets and Numbering
Formatted: Indent: First line: 11 ch
Formatted: Indent: Left: 0", First line: 11 ch
Formatted: Bullets and Numbering
Formatted: Indent: First line: 11 ch
Formatted: Indent: Left: 0", First line: 11 ch
Formatted: Bullets and Numbering
Formatted: Indent: First line: 11 ch
Formatted: Indent: Left: 0", First line: 11 ch
Formatted: Bullets and Numbering
Formatted: Indent: First line: 11 ch
PDS: Rev :F STATUS:Released Printed: May 16, 2012
TYPE PRODUCT SPECIFICATION NUMBER BUS-12-023
TITLE PAGE REVISION
Mini-Jump – Gold or GXT Plated 18 of 17 FED
AUTHORIZED BY DATE
H.
SUNDYS.FierroJ.ZH
OU
4-14- APR
0506/12/065/1
5/2012
CLASSIFICATION
CONFIDENTIALUNRESTRICTED
This docum ent is the property of and em bodies CON FIDENTIA L and PROPRIE T A R Y informati on of FCI.FCI Electronics. No part of the information shown on this document may be used
in any way withou t the written consent of FCI .Electronics.
Form E-3005
Rev B 07/30/04A 02/12/01
V04-078220603
GS-01-001
Copyright FCI
Form E-3334
Rev E
GS-01-001
NOTES (Optional)
RECORD RETENTION (If Applicable)
The following constitutes the recommended order and paragraph numbering
scheme in compliance with GS-01-001. Paragraphs that are not needed shall be eliminated, and
subsequent paragraphs renumbered.
Please delete this note after reading.
OBJECTIVE
SCOPE
GENERAL
DEFINITIONS
PROCEDURE
REFERENCE DOCUMENTS (If Applicable)
NOTES (Optional)
RECORD RETENTION (If Applicable)
The following constitutes the recommended order and paragraph numbering
scheme in compliance with GS-01-001. Paragraphs that are not needed shall be eliminated, and
subsequent paragraphs renumbered.
Please delete this note after reading.
1.0OBJECTIVE
Formatted ... [1]
Formatted: Bullets and Numbering ... [2]
Formatted ... [3]
Formatted ... [4]
Formatted: Bullets and Numbering ... [5]
Formatted ... [6]
Formatted ... [7]
Formatted ... [8]
Formatted: Bullets and Numbering ... [9]
Formatted ... [10]
Formatted ... [11]
Formatted: Bullets and Numbering ... [12]
Formatted ... [13]
Formatted ... [14]
Formatted: Bullets and Numbering ... [15]
Formatted ... [16]
Formatted ... [17]
Formatted: Bullets and Numbering ... [18]
Formatted ... [19]
Formatted ... [20]
Formatted: Bullets and Numbering ... [21]
Formatted ... [22]
Formatted ... [23]
Formatted: Bullets and Numbering ... [24]
Formatted ... [25]
Formatted ... [26]
Formatted: Bullets and Numbering ... [27]
Formatted ... [28]
Formatted ... [29]
Formatted: Bullets and Numbering ... [30]
Formatted ... [31]
Formatted ... [32]
Formatted ... [33]
Formatted: Bullets and Numbering ... [34]
PDS: Rev :F STATUS:Released Printed: May 16, 2012
TYPE PRODUCT SPECIFICATION NUMBER BUS-12-023
TITLE PAGE REVISION
Mini-Jump – Gold or GXT Plated 19 of 17 FED
AUTHORIZED BY DATE
H.
SUNDYS.FierroJ.ZH
OU
4-14- APR
0506/12/065/1
5/2012
CLASSIFICATION
CONFIDENTIALUNRESTRICTED
This docum ent is the property of and em bodies CON FIDENTIA L and PROPRIE T A R Y informati on of FCI.FCI Electronics. No part of the information shown on this document may be used
in any way withou t the written consent of FCI .Electronics.
Form E-3005
Rev B 07/30/04A 02/12/01
V04-078220603
GS-01-001
Copyright FCI
Form E-3334
Rev E
GS-01-001
2.0SCOPE
3.0GENERAL
4.0DEFINITIONS
5.0PROCEDURE
6.0REFERENCE DOCUMENTS (If Applicable)
7.0NOTES (Optional)
8.0RECORD RETENTION (If Applicable)
Formatted: Bullets and Numbering
Formatted: Bullets and Numbering
Formatted: Bullets and Numbering
Formatted: Bullets and Numbering
Formatted: Bullets and Numbering
Formatted: Bullets and Numbering
Formatted: Bullets and Numbering
PDS: Rev :F STATUS:Released Printed: May 16, 2012
Page 18: [1] Formatted pdselxadmin2 5/16/2012 7:01:00 AM
Indent: Left: 0", First line: 11 ch
Page 18: [2] Change lkline 4/26/2001 7:20:00 AM
Formatted Bullets and Numbering
Page 18: [3] Formatted zhoujan 5/4/2012 1:49:00 PM
Indent: First line: 11 ch
Page 18: [4] Formatted pdselxadmin2 5/16/2012 7:01:00 AM
Indent: Left: 0", First line: 11 ch
Page 18: [5] Change lkline 4/26/2001 7:20:00 AM
Formatted Bullets and Numbering
Page 18: [6] Formatted pdselxadmin2 5/16/2012 7:01:00 AM
Indent: First line: 11 ch
Page 18: [7] Formatted zhoujan 5/4/2012 1:49:00 PM
Indent: First line: 11 ch
Page 18: [8] Formatted pdselxadmin2 5/16/2012 7:01:00 AM
Indent: Left: 0", First line: 11 ch
Page 18: [9] Change Irene T Myers 5/18/2001 2:17:00 PM
Formatted Bullets and Numbering
Page 18: [10] Formatted zhoujan 5/4/2012 1:49:00 PM
Indent: First line: 11 ch
Page 18: [11] Formatted pdselxadmin2 5/16/2012 7:01:00 AM
Indent: Left: 0", First line: 11 ch
Page 18: [12] Change Irene T Myers 5/18/2001 2:17:00 PM
Formatted Bullets and Numbering
Page 18: [13] Formatted zhoujan 5/4/2012 1:49:00 PM
Indent: First line: 11 ch
Page 18: [14] Formatted pdselxadmin2 5/16/2012 7:01:00 AM
Indent: Left: 0", First line: 11 ch
Page 18: [15] Change Irene T Myers 5/18/2001 2:17:00 PM
Formatted Bullets and Numbering
Page 18: [16] Formatted zhoujan 5/4/2012 1:49:00 PM
Indent: First line: 11 ch
Page 18: [17] Formatted pdselxadmin2 5/16/2012 7:01:00 AM
Indent: Left: 0", First line: 11 ch
Page 18: [18] Change Irene T Myers 5/18/2001 2:17:00 PM
Formatted Bullets and Numbering
Page 18: [19] Formatted zhoujan 5/4/2012 1:49:00 PM
Indent: First line: 11 ch
Page 18: [20] Formatted pdselxadmin2 5/16/2012 7:01:00 AM
Indent: Left: 0
"
First line: 11 ch
PDS: Rev :F STATUS:Released Printed: May 16, 2012
Page 18: [22] Formatted zhoujan 5/4/2012 1:49:00 PM
Indent: First line: 11 ch
Page 18: [23] Formatted pdselxadmin2 5/16/2012 7:01:00 AM
Indent: Left: 0", First line: 11 ch
Page 18: [24] Change Irene T Myers 5/18/2001 2:17:00 PM
Formatted Bullets and Numbering
Page 18: [25] Formatted zhoujan 5/4/2012 1:49:00 PM
Indent: First line: 11 ch
Page 18: [26] Formatted pdselxadmin2 5/16/2012 7:01:00 AM
Indent: Left: 0", First line: 11 ch
Page 18: [27] Change Irene T Myers 5/18/2001 2:17:00 PM
Formatted Bullets and Numbering
Page 18: [28] Formatted zhoujan 5/4/2012 1:49:00 PM
Indent: First line: 11 ch
Page 18: [29] Formatted pdselxadmin2 5/16/2012 7:01:00 AM
Indent: Left: 0", First line: 11 ch
Page 18: [30] Change Irene T Myers 5/18/2001 2:17:00 PM
Formatted Bullets and Numbering
Page 18: [31] Formatted zhoujan 5/4/2012 1:49:00 PM
Indent: First line: 11 ch
Page 18: [32] Formatted pdselxadmin2 5/16/2012 7:01:00 AM
Indent: First line: 11 ch
Page 18: [33] Formatted zhoujan 5/4/2012 1:49:00 PM
Indent: First line: 11 ch
Page 18: [34] Change lkline 4/18/2001 10:09:00 AM
Formatted Bullets and Numbering
PDS: Rev :F STATUS:Released Printed: May 16, 2012
