DATA SHEET AAT3681A 500mA USB Port or AC Adapter Li-Ion/Polymer Battery Charger General Description Features The AAT3681A BatteryManager is an integrated single cell lithium-ion/polymer battery charger IC, designed to operate from a DC power source or USB port up to an input voltage of 7.5V. It requires just one external component. * USB or AC Adapter System Power Charger Programmable from 15mA to 500mA * 4.0V ~ 7.5V Input Voltage Range * High Level of Integration with Internal: Charging Device Reverse Blocking Diode Constant Regulated Output Voltage: 4.1 in AAT3681A-5 4.2 in AAT3681A-1/-2/-4 * Automatic Current Sensing * Automatic Recharge Sequencing * Full Battery Charge Auto Turn Off/Sleep Mode/Charge Termination * Shutdown Current <1A * Automatic Trickle Charge for Battery Pre-Conditioning (AAT3681A-1/AAT3681A-4 is No Trickle Charge Option) * Over-Voltage and Emergency Thermal Protection * Power On Reset and Soft Start * LED Status Pin * 8-Pin 2.0 x 2.0mm SC70JW Package The AAT3681A precisely regulates battery charge voltage and current for 4.2V (4.375V option) lithium-ion/ polymer battery cells. When charged from an AC adapter or USB port, the battery charging current can be set by an external resistor up to 500mA. Battery charge state is continuously monitored for fault conditions. In the event of an over-voltage, short-circuit, or over-temperature failure, the device will automatically shut down, thus protecting the charging device, control system, and the battery under charge. A status monitor output pin is provided to indicate the battery charge status by directly driving an external LED. The AAT3681A is available in a Pb-free, thermally enhanced, space-saving 8-pin 2.0 x 2.0mm SC70JW package and is specified for operation over the -40C to +85C temperature range. Applications * * * * * * * Bluetooth(R) Headsets DECT Headsets Digital Still Cameras MP3, Portable Music, and Portable Media Players Personal Data Assistants (PDAs) Wrist Watches Other Lithium-Ion/Polymer Battery-Powered Devices Typical Application Adapter/USB Input BATT+ ADP BAT AAT3681A Enable C BATTBattery Pack STAT EN ISET GND RSET Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201883C * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * November 19, 2012 1 DATA SHEET AAT3681A 500mA USB Port or AC Adapter Li-Ion/Polymer Battery Charger Pin Description Pin # Symbol Type 1 EN In 2 3 4 5 6, 7, 8 ISET BAT ADP STAT GND In/Out In/Out Power In Out Power Function Enable pin. AAT3681A, AAT3681A-1, AAT3681A-4, AAT3681A-5: Logic high enables the IC (internal pull down 6M resistor). AAT3681A-2: Logic low enables the IC (internal pull down resistor). Connect resistor here to set the charge current. Battery charging and sensing. Input from USB/adapter charger. Open drain status pin. Ground connection. Pin Configuration SC70JW-8 (Top View) 2 EN 1 8 GND ISET 2 7 GND BAT 3 6 GND ADP 4 5 STAT Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201883C * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * November 19, 2012 DATA SHEET AAT3681A 500mA USB Port or AC Adapter Li-Ion/Polymer Battery Charger AAT3681A Feature Options Product Trickle Charge Enable Charge Termination Threshold Current Constant Regulated Output Voltage VCO(REG) AAT3681A AAT3681A-1 AAT3681A-2 AAT3681A-4 AAT3681A-5 Yes No Yes No Yes Active High Active High Active Low Active High Active High 10% 10% 10% 10% 10% 4.2 (Optional 4.1V) 4.2 4.2 4.2 4.1 Absolute Maximum Ratings1 Symbol VP VN TA TJ TLEAD Description ADP Continuous BAT, STAT, ISET, EN Operating Temperature Range Junction Temperature Range Maximum Soldering Temperature (at Leads) Value -0.3 to 8.0 -0.3 to VP + 0.3 -40 to 85 -40 to 150 300 Units V C Thermal Information2 Symbol PD qJA Description Maximum Power Dissipation Maximum Thermal Resistance Value Units 0.687 160 W C/W 1. Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum Rating should be applied at any one time. 2. Mounted on an FR4 board. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201883C * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * November 19, 2012 3 DATA SHEET AAT3681A 500mA USB Port or AC Adapter Li-Ion/Polymer Battery Charger Electrical Characteristics1 VADP = 5V, TA = -40C to +85C, unless otherwise noted. Typical values are TA = 25C. Symbol Description Conditions Operation VADP Adapter Voltage Range VUVLO Under-Voltage Lockout (UVLO) IOP UVLO Hysteresis Operating Current ISHUTDOWN Shutdown Current Reverse Leakage Current from BAT Pin Voltage Regulation ILEAKAGE VCO(REG) Constant Output Voltage Accuracy DVCH/VCH VMIN Output Charge Voltage Tolerance Preconditioning Voltage Threshold Battery Recharge Voltage VRCH Threshold Current Regulation Charge Current Programmable ICH Range2 Charge Current Regulation DICH/ICH Tolerance VSET ISET Pin Voltage KI_A Current Set Factor: ICH/ISET Charging Devices RDS(ON) Charging Transistor On Resistance Logic Control/Protection VEN(H) Input High Threshold VEN(L) Input Low Threshold VSTAT Output Low Voltage ISTAT STAT Pin Current Sink Capability VOVP Over-Voltage Protection Threshold ITK/ICH ITERM/ICH Pre-Charge Current Charge Termination Threshold Current Min Typ 4.0 Rising Edge for AAT3681A/-1/-2 Rising Edge for AAT3681A-4/-5 Charge Current = 200mA VBAT = 4.25V, VEN = GND (AAT3681A, AAT3681A-1, AAT3681A-4) VBAT = 4.25V, VEN = 5V (AAT3681A-2) VBAT = 4V, ADP Pin Open For AAT3681A/-1/-2/-4 AAT3681A-5 Only AAT3681A, AAT3681A-2 Only AAT3681A, AAT3681A-1, AAT3681A-2 and AAT3681A-4 Only; Measured from VCO(REG) 4.158 4.059 2.85 Max Units 7.5 V 3.0 3.2 150 0.5 1 mV mA 0.3 1 A 0.4 2 A 4.20 4.10 0.5 3.0 4.242 4.141 V V 3.15 -0.1 15 VADP = 5.5V V 500 mA 10 % 2 800 V 0.6 1 W 0.4 0.4 8 4.4 V V V mA V 10 % 10 % 1.6 STAT Pin Sinks 4mA ICH = 100mA; AAT3681A, AAT3681A-2, and AAT3681A-5 Only AAT3681A, AAT3681A-1, AAT3681A-2, AAT3681A-4, and AAT3681A-5 Only % V 1. The AAT3681A output charge voltage is specified over the 0 to 70C ambient temperature range; operation over the -40C to +85C temperature range is guaranteed by design. 2. Achievable charge current may be limited by power dissipation capability of the package under certain operating conditions. See "Thermal Considerations" section of this datasheet. 4 Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201883C * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * November 19, 2012 DATA SHEET AAT3681A 500mA USB Port or AC Adapter Li-Ion/Polymer Battery Charger Typical Characteristics Operating Supply Current vs. RSET (VIN = 5V) 1000 1000 100 100 ISUPPLY (A) ICH (mA) Constant Charging Current vs. Set Resistor Values 10 1 10 100 VBAT = 2.85V 10 1 1 VBAT = 3.6V 1000 1 10 RSET (k) RSET (k) Constant Regulated Output Voltage vs. Input Voltage (AAT3681A, AAT3681A-1/-2/-4; RSET = 8.06k) 4.23 4.215 4.22 4.210 VCO(REG) (V) Battery Voltage (V) Constant Regulated Output Voltage vs. Temperature (AAT3681A, AAT3681A-1/-2/-4) 4.220 4.205 4.200 4.195 4.190 4.21 4.20 4.19 4.18 4.185 4.180 4.5 5.0 5.5 6.0 6.5 7.0 7.5 4.17 -50 -25 0 25 50 75 Input Voltage (V) Temperature (C) Constant Regulated Output Voltage vs. Input Voltage Constant Regulated Output Voltage vs. Temperature (AAT3681A-4.1, AAT3681A-5 Only) 4.13 4.11 4.09 4.07 4.05 5.0 5.5 6.0 6.5 Input Voltage (V) 7.0 100 (AAT3681A-4.1 and AAT3681A-5 Only) 4.15 End Of Charge Voltage Regulation (V) End Of Charge Voltage Regulation (V) 100 7.5 4.110 4.105 4.100 4.095 4.090 4.085 4.080 -40 -15 10 35 60 85 Temperature (C) Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201883C * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * November 19, 2012 5 DATA SHEET AAT3681A 500mA USB Port or AC Adapter Li-Ion/Polymer Battery Charger Typical Characteristics Charging Current vs. Battery Voltage Charging Current vs. Battery Voltage (AAT3681A, AAT3681A-2, and AAT3681A-5 only) (AAT3681A-1 and AAT3681A-4 only) 600 600 RSET = 3.24k RSET = 5.36k 400 300 RSET = 8.06k 200 RSET = 16.2k 100 0 2.9 3.1 400 RSET = 5.36k 300 RSET = 8.06k 200 RSET = 16.2k 100 RSET = 31.6k 2.7 RSET = 3.24k 500 ICH (mA) ICH (mA) 500 3.3 3.5 3.7 3.9 4.1 0 4.3 RSET = 31.6k 2.7 2.9 3.1 3.3 Battery Charging Current vs. Input Voltage 220 210 200 190 180 VBAT = 3.3V VBAT = 3.6V VBAT = 3.9V VBAT = 4.0V 170 160 5.5 6.0 6.5 7.0 7.5 600 RSET = 3.24K RSET = 5.36K 500 120 300 200 100 0 -100 2.6 2.8 3.0 3.4 3.6 3.8 4.0 4.2 210 VBAT = 5.0V VBAT = 5.5V VBAT = 6.0V VBAT = 6.5V VBAT = 7.0V VBAT = 7.5V 208 205 203 200 198 195 40 193 2.4 2.6 2.8 3.0 3.2 3.4 3.6 Battery Voltage (V) 6 3.2 (RSET = 8.06k) 80 0 2.2 RSET = 31.6K Constant Charging Current vs. Temperature ICH (mA) Battery Charging Current (mA) (AAT3681A-4.1 and AAT3681A-5 Only) 160 RSET = 8.06K RSET = 16.2K Battery Voltage (V) Battery Charging Current vs. Battery Voltage 200 4.3 400 Input Voltage (V) 240 4.1 (AAT3681A-4.1 and AAT3681A-5 Only) Battery Charging Current (mA) Battery Charging Current (mA) 230 5.0 3.9 Charging Current vs. Battery Voltage (AAT3681A-4.1 and AAT3681A-5 only; VCO(REG) = 4.1V) 4.5 3.7 VBAT (V) VBAT (V) 150 4.0 3.5 3.8 4.0 4.2 190 -50 -25 0 25 50 Temperature (C) Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201883C * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * November 19, 2012 75 100 DATA SHEET AAT3681A 500mA USB Port or AC Adapter Li-Ion/Polymer Battery Charger Typical Characteristics Constant Charging Current vs. Input Voltage Operating Current vs. Temperature (RSET = 8.06k) (RSET = 8.06k) 550 260 500 240 220 VBAT = 3.3V IOP (A) Charging Current (mA) 280 200 180 160 VBAT = 3.6V 140 VBAT = 4.0V 120 4 4.5 450 400 350 5 5.5 6 6.5 7 300 -50 7.5 -25 0 Input Voltage (V) Preconditioning Threshold Voltage (V) VMIN (V) 3.02 3.01 3 2.99 2.98 25 50 75 2.95 2.94 2.93 2.92 2.91 2.90 5.0 100 5.5 Temperature (C) 6.5 7.0 7.5 Preconditioning Charge Current vs. Temperature (RSET = 8.06k; AAT3681A, AAT3681A-2,and AAT3681A-5 Only) (AAT3681AIJS-4.1-T1 Only) 20.8 3.00 20.6 2.98 20.4 2.96 ITRICKLE (mA) Preconditioning Threshold Voltage (V) 6.0 Input Voltage (V) Preconditioning Threshold Voltage vs. Temperature 2.94 2.92 2.90 2.88 2.86 2.84 20.2 20.0 19.8 19.6 19.4 2.82 2.80 -40 100 (AAT3681A-4.1 and AAT3681A-5 Only) 3.03 0 75 Preconditioning Voltage Threshold vs. Input Voltage (RSET = 8.06k; AAT3681A, AAT3681A-2, and AAT3681A-5 Only) -25 50 Temperature (C) Preconditioning Threshold Voltage vs. Temperature 2.97 -50 25 -15 10 35 Temperature (C) 60 85 19.2 -50 -25 0 25 50 75 100 Temperature (C) Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201883C * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * November 19, 2012 7 DATA SHEET AAT3681A 500mA USB Port or AC Adapter Li-Ion/Polymer Battery Charger Typical Characteristics Preconditioning Charge Current vs. Input Voltage 35 (RSET = 8.06k; AAT3681A, AAT3681A-1, AAT3681A-2, and AAT3681A-4 Only) RSET = 5.36k 30 4.18 4.16 25 4.14 RSET = 8.06k 20 15 RSET = 16.2k 10 4.12 4.10 4.08 4.06 5 0 Recharging Threshold Voltage vs. Temperature VRCH (V) Trickle Charge Current (mA) (AAT3681A, AAT3681A-2, and AAT3681A-5 Only) 4.04 RSET = 31.6k 4 4.5 5 5.5 6 6.5 7 4.02 7.5 -50 -25 0 Input Voltage (V) Recharging Threshold Voltage vs. Temperature Shutdown Current (nA) End Of Charge Voltage Regulation (V) 100 1800 4.030 4.010 3.990 3.970 3.950 -40 -15 10 35 60 1600 1400 1000 800 600 400 200 0 4.0 85 85C 1200 -40C 25C 4.5 5.0 Temperature (C) 5.5 6.0 6.5 7.0 7.5 Supply Voltage (V) Input Enable High Voltage vs. Supply Voltage (RSET = 8.06k) Input Enable Low Voltage vs. Supply Voltage (RSET = 8.06k) 1.5 1.2 1.4 -40C 1.1 1.3 -40C 1.2 VIL_ENABLE (V) VIH_ENABLE (V) 75 (RSET = 8.06k) 4.050 1.1 1.0 0.9 0.8 25C 0.7 85C 4.0 4.5 5.0 5.5 6.0 VIN (V) 1.0 0.9 0.8 0.7 85C 25C 0.6 0.5 0.6 8 50 Shutdown Current vs. Supply Voltage (AAT3681A-4.1 and AAT3681A-5 Only) 0.5 25 Temperature (C) 6.5 7.0 7.5 0.4 4.0 4.5 5.0 5.5 6.0 6.5 VIN (V) Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201883C * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * November 19, 2012 7.0 7.5 DATA SHEET AAT3681A 500mA USB Port or AC Adapter Li-Ion/Polymer Battery Charger Functional Block Diagram Reverse Blocking ADP BAT Current Compare Constant Current ISET STAT Charge Status CV/ Precharge Charge Control UVLO OverTemperature Protection GND EN Functional Description The AAT3681A is a high performance battery charger designed for single cell lithium-ion/polymer batteries with up to 500mA of charge current from an external power source. It is a stand-alone charging solution, with just one external component required for complete functionality. The AAT3681A precisely regulates battery charge voltage and current for 4.2V lithium-ion/polymer battery cells. The AAT3681A-5 regulates battery charge voltage for 4.1V Lithium-ion/polymer battery cells. The adapter/USB charge input constant current level can be programmed up to 500mA for rapid charging applications. The AAT3681A/-1/-2/-4/-5 is rated for operation from -40C to +85C. In the event of operating ambient temperatures exceeding the power dissipation abilities of the device package for a given constant current charge level, the charge control will enter into thermal limit. A status monitor output pin is provided to indicate the battery charge state by directly driving one external LED. Device junction temperature and charge state are fully monitored for fault conditions. In the event of an overvoltage or over-temperature failure, the device will automatically shut down, protecting the charging device, control system, and the battery under charge. Charging Operation The AAT3681A has four basic modes for the battery charge cycle: pre-conditioning/trickle charge; constant current/fast charge; constant voltage; and charge termination (see Figure 1). (AAT3681A-1 and AAT3681A-4 do not have trickle charge.) Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201883C * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * November 19, 2012 9 DATA SHEET AAT3681A 500mA USB Port or AC Adapter Li-Ion/Polymer Battery Charger Charge Complete Voltage Preconditioning Trickle Charge Phase Constant Current Charge Phase I = Max CC Regulated Current Constant Voltage Charge Phase Battery Discharge Constant Voltage Charge Phase Battery Recharge Voltage Threshold Constant Current Mode Voltage Threshold Trickle Charge and Termination Threshold I = CC / 10 Figure 1: Current vs. Voltage Profile During Charging Phases. Battery Preconditioning Constant Voltage Charging Before the start of charging, the AAT3681A checks several conditions in order to assure a safe charging environment. The input supply must be above the minimum operating voltage, or under-voltage lockout threshold (VUVLO), for the charging sequence to begin. When these conditions have been met and a battery is connected to the BAT pin, the AAT3681A checks the state of the battery. If the cell voltage is below the preconditioning voltage threshold (VMIN), the charge control begins preconditioning the cell. The battery preconditioning trickle charge current is equal to the fast charge constant current divided by 10. For example, if the programmed fast charge current is 300mA, then the preconditioning mode (trickle charge) current will be 30mA. Cell preconditioning is a safety precaution for deeply discharged battery cells and also aids in limiting power dissipation in the pass transistor when the voltage across the device is at the greatest potential. The system transitions to a constant voltage charging mode when the battery voltage reaches the constant output voltage charge regulation threshold (VCO(REG)) during the constant current fast charge phase. The regulation voltage level is factory programmed to 4.2V (0.5%) for AAT3681A/-1/-2/-4 and 4.1 (0.5%) for AAT3681A-5. Charge current in the constant voltage mode drops as the battery cell under charge reaches its maximum capacity. Constant Current Charging Consuming very low current in sleep state, the AAT3681A minimizes battery drain when it is not charging. This feature is particularly useful in applications where the input supply level may fall below the battery charge or under-voltage lockout level. In such cases where the AAT3681A input voltage drops, the device will enter sleep state and automatically resume charging once the input supply has recovered from the fault condition. Battery cell preconditioning continues until the voltage on the BAT pin exceeds the preconditioning voltage threshold (VMIN). At this point, the AAT3681A begins the constant current charging phase. The charge constant current (ICH) amplitude is programmed by the user via the RSET resistor. The AAT3681A remains in the constant current charge mode until the battery reaches the constant voltage regulation point, VCO(REG). 10 End of Charge Cycle Termination and Recharge Sequence When the charge current drops to 10% of the programmed fast charge current level in the constant voltage mode, the device terminates charging and goes into a sleep state. The charger will remain in a sleep state until the battery voltage decreases to a level below the battery recharge voltage threshold (VRCH). Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201883C * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * November 19, 2012 DATA SHEET AAT3681A 500mA USB Port or AC Adapter Li-Ion/Polymer Battery Charger System Operation Flow Chart Enable No Power On Reset Yes Power Input Voltage VIN > VUVLO Yes Shut Down Yes Fault Conditions Monitoring OV, OT Charge Control No (AAT3681A, AAT3681A-2, AAT3681A-5) No (AAT3681A-1, AAT3681A-4) Preconditioning Test V MIN > VBAT Yes Preconditioning (Trickle Charge) Yes Constant Current Charge Mode No No Recharge Test V RCH > VBAT Yes Current Phase Test V CO(REG) > VBAT No Voltage Phase Test IBAT > ITERM Yes No Constant Voltage Charge Mode No (AAT3681A, AAT3681A-1, AAT3681A-2, AAT3681A-4, AAT3681A-5, AAT3681A-6) Charge Completed Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201883C * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * November 19, 2012 11 DATA SHEET AAT3681A 500mA USB Port or AC Adapter Li-Ion/Polymer Battery Charger Application Information Adapter or USB Power Input Constant current charge levels up to 500mA may be programmed by the user when powered from a sufficient input power source. The AAT3681A will operate from the adapter input over a 4.0V to 7.5V range. The constant current fast charge current for the adapter input is set by the RSET resistor connected between ISET and ground. Refer to Table 1 for recommended RSET values for a desired constant current charge level. Adapter Input Charge Inhibit and Resume Programming Charge Current The fast charge constant current charge level is user programmed with a set resistor placed between the ISET pin and ground. The accuracy of the fast charge, as well as the preconditioning trickle charge current, is dominated by the tolerance of the set resistor used. For this reason, a 1% tolerance metal film resistor is recommended for the set resistor function. Fast charge constant current levels from 15mA to 500mA may be set by selecting the appropriate resistor value from Table 1. Nominal ICHARGE (mA) Set Resistor Value (kW) 500 450 400 350 300 250 200 150 100 50 40 30 20 15 3.24 3.57 4.12 4.64 5.36 6.49 8.06 10.7 16.2 31.6 38.3 53.6 78.7 105 The AAT3681A has a UVLO and power on reset feature so that if the input supply to the ADP pin drops below the UVLO threshold, the charger will suspend charging and shut down. When power is re-applied to the ADP pin or the UVLO condition recovers, the system charge control will assess the state of charge on the battery cell and will automatically resume charging in the appropriate mode for the condition of the battery. Enable / Disable The AAT3681A provides an enable function to control the charger IC on and off. The EN pin functions as follows on the various AAT3681A options: AAT3681A-2: The enable (EN) pin is internally pulled down. When left open or pulled to a logic low level, the AAT3681A-2 is enabled. When pulled to a logic high level, the AAT3681A-2 will be shut down and forced into the sleep state. Charging will be halted regardless of the battery voltage or charging state. When the device is re-enabled, the charge control circuit will automatically reset and resume charging functions with the appropriate charging mode based on the battery charge state and measured cell voltage on the BAT pin. Constant Current Table 1:Charging RSET Values. vs. Set Resistor Values 1000 ICH (mA) AAT3681A, AAT3681A-1, AAT3681A-4, and AAT3681A-5: The enable (EN) pin is internally pulled down through a 6M resistor. When pulled to a logic high level, the AAT3681A is enabled. When left open or pulled to a logic low level, the AAT3681A will be shut down and forced into the sleep state. 100 10 1 1 10 100 1000 RSET (k) Figure 2: Constant Charging Current vs. Set Resistor Values. Protection Circuitry Over-Voltage Protection An over-voltage event is defined as a condition where the voltage on the BAT pin exceeds the maximum battery charge voltage and is set by the over-voltage protection threshold (VOVP). If an over-voltage condition 12 Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201883C * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * November 19, 2012 DATA SHEET AAT3681A 500mA USB Port or AC Adapter Li-Ion/Polymer Battery Charger Over-Temperature Shutdown The AAT3681A has a thermal protection control circuit which will shut down charging functions should the internal die temperature exceed the preset thermal limit threshold. Once the internal die temperature falls below the thermal limit, normal operation will resume the previous charging state. Charge Status Output The AAT3681A provides battery charge status via a status pin. This pin is internally connected to an N-channel open drain MOSFET, which can be used to drive an external LED. The status pin can indicate the following conditions: Event Description Status No battery charging activity Battery charging via adapter or USB port Charging completed OFF ON OFF Table 2: LED Status Indicator. The LED should be biased with as little current as necessary to create reasonable illumination; therefore, a ballast resistor should be placed between the LED cathode and the STAT pin. LED current consumption will add to the overall thermal power budget for the device package, hence it is good to keep the LED drive current to a minimum. A 2mA should be sufficient to drive most lowcost green or red LEDs. It is not recommended to exceed 8mA for driving an individual status LED. The required ballast resistor values can be estimated using the following formulas: R1 = (VADP - VF(LED)) ILED Thermal Considerations The AAT3681A is offered in a SC70JW-8 package which can provide up to 687mW of power dissipation when it is properly bonded to a printed circuit board and has a maximum thermal resistance of 160C/W. Many considerations should be taken into account when designing the printed circuit board layout, as well as the placement of the charger IC package in proximity to other heat generating devices in a given application design. The ambient temperature around the charger IC will also have an effect on the thermal limits of a battery charging application. The maximum limits that can be expected for a given ambient condition can be estimated by the following discussion. First, the maximum power dissipation for a given situation should be calculated: PD(MAX) = (TJ(MAX) - TA) JA Where: PD(MAX) = Maximum Power Dissipation (W) qJA = Package Thermal Resistance (C/W) TJ(MAX) = Maximum Device Junction Temperature (C) [135C] TA = Ambient Temperature (C) Figure 3 shows the relationship of maximum power dissipation and ambient temperature of AAT3681A. 1000 800 PD(MAX) (mW) occurs, the AAT3681A charge control will shut down the device until the voltage on the BAT pin drops below VOVP. The AAT3681A will resume normal charging operation after the over-voltage condition is removed. 600 400 200 0 0 20 40 60 80 100 TA (C) Example: R1 = (5.5V - 2.0V) = 1.75k 2mA Figure 3: Maximum Power Dissipation. Note: Red LED forward voltage (VF) is typically 2.0V @ 2mA. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201883C * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * November 19, 2012 13 DATA SHEET AAT3681A 500mA USB Port or AC Adapter Li-Ion/Polymer Battery Charger Next, the power dissipation can be calculated by the following equation: PD = [(VIN - VBAT) * ICH + (VIN * IOP)] Where: PD VIN VBAT ICH IOP = = = = Total Power Dissipation by the Device Input Voltage Battery Voltage as Seen at the BAT Pin Constant Charge Current Programmed for the Application = Quiescent Current Consumed by the Charger IC for Normal Operation [0.5mA] By substitution, we can derive the maximum charge current before reaching the thermal limit condition (thermal cycling). The maximum charge current is the key factor when designing battery charger applications. ICH(MAX) = (PD(MAX) - VIN * IOP) VIN - VBAT (TJ(MAX) - TA) - V * I IN OP JA ICH(MAX) = VIN - VBAT In general, the worst condition is the greatest voltage drop across the charger IC, when battery voltage is charged up to the preconditioning voltage threshold. Figure 4 shows the maximum charge current in different ambient temperatures without PCB thermal enhancements. 500 450 ICH(MAX) (mA) 400 TA = 25C 350 Capacitor Selection Input Capacitor In general, it is good design practice to place a decoupling capacitor between the ADP pin and GND. An input capacitor in the range of 1F to 22F is recommended. If the source supply is unregulated, it may be necessary to increase the capacitance to keep the input voltage above the under-voltage lockout threshold during device enable and when battery charging is initiated. If the AAT3681A adapter input is to be used in a system with an external power supply source, such as a typical AC-to-DC wall adapter, then a CIN capacitor in the range of 10F should be used. A larger input capacitor in this application will minimize switching or power transient effects when the power supply is "hot plugged" in. Output Capacitor The AAT3681A only requires a 1F ceramic capacitor on the BAT pin to maintain circuit stability. This value should be increased to 10F or more if the battery connection is made any distance from the charger output. If the AAT3681A is to be used in applications where the battery can be removed from the charger, such as with desktop charging cradles, an output capacitor greater than 10F may be required to prevent the device from cycling on and off when no battery is present. Printed Circuit Board Layout Considerations For the best results, it is recommended to physically place the battery pack as close as possible to the AAT3681A BAT pin. To minimize voltage drops on the PCB, keep the high current carrying traces adequately wide. Refer to the AAT3681A evaluation board for a good layout example (see Figures 5 and 6). TA = 45C 300 250 200 150 100 50 TA = 85C 0 4.25 4.5 4.75 TA = 60C 5 5.25 5.5 5.75 6 6.25 6.5 6.75 7 VIN (V) Figure 4: Maximum Charging Current Before Thermal Cycling Becomes Active. 14 Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201883C * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * November 19, 2012 DATA SHEET AAT3681A 500mA USB Port or AC Adapter Li-Ion/Polymer Battery Charger Figure 5: AAT3681A Evaluation Board Top Side Layout. Figure 6: AAT3681A Evaluation Board Bottom Side Layout. VBAT VIN(ADP) JP2 C1 10F 1 2 3 4 R8 8.06K AAT3681A EN ISET BAT ADP GND GND GND STAT 8 7 6 5 C2 2.2F U1 (SC70JW-8) JP1 0 D1 R1 RED LED 1K Figure 7: AAT3681A Evaluation Board Schematic Diagram. Component Part Number Description Manufacturer U1 R1 R8 JP1 C1 C2 JP2 LED1 AAT3681AIJS-T1 Chip Resistor Chip Resistor Chip Resistor GRM21BR61A106KE19L GRM21BR71A225KA01L PRPN401PAEN CMD15-21SRC/TR8 USB/ADP Battery Charger; SC70JW-8 Package 1kW, 5%, 1/4W; 0603 8.06kW, 1%, 1/4W; 0805 0W, 5%, 1/4W; 0603 Ceramic 10F 10V 10% X5R 0805 Ceramic 2.2F 10V 10% X7R 0805 Connecting Header, 2mm Zip Red LED; 1206 Skyworks Vishay Murata Sullins Electronics Chicago Miniature Lamp Table 3: AAT3681A Evaluation Board Bill of Materials. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201883C * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * November 19, 2012 15 DATA SHEET AAT3681A 500mA USB Port or AC Adapter Li-Ion/Polymer Battery Charger Ordering Information Trickle Charge Enable Package Marking1 Part Number (Tape and Reel)2 Yes Yes No Yes No Yes Active High Active High Active High Active Low Active High Active High SC70JW-8 SC70JW-8 SC70JW-8 SC70JW-8 SC70JW-8 SC70JW-8 E4XYY UTXYY UEXYY VSXYY A9XYY F2XYY AAT3681AIJS-4.1-T1 AAT3681AIJS-4.2-T1 AAT3681AIJS-4.2-1-T1 AAT3681AIJS-4.2-2-T1 AAT3681AIJS-4.2-4-T1 AAT3681AIJS-4.1-5-T1 Skyworks GreenTM products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of GreenTM, document number SQ04-0074. Package Information SC70JW-8 2.20 0.20 1.75 0.10 0.50 BSC 0.50 BSC 0.50 BSC 0.225 0.075 2.00 0.20 0.100 0.15 0.05 0.45 0.10 4 4 0.05 0.05 7 3 1.10 MAX 0.85 0.15 0.048REF 2.10 0.30 All dimensions in millimeters. 1. XYY = assembly and date code. 2. Sample stock is generally held on part numbers listed in BOLD. 16 Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201883C * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * November 19, 2012 DATA SHEET AAT3681A 500mA USB Port or AC Adapter Li-Ion/Polymer Battery Charger Copyright (c) 2012 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. ("Skyworks") products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and "Breakthrough Simplicity" are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201883C * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * November 19, 2012 17 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Skyworks: AAT3681AIJS-4.2-T1 AAT3681AIJS-4.1-T1