AWT6301 Cellular Dual Mode AMPS/CDMA 3.4 V/28 dBm Linear Power Amplifier Module PRELIMINARY DATA SHEET - Rev 1.2 FEATURES * InGaP HBT Technology * High Efficiency: 53 % AMPS, 39 % CDMA * Low Quiescent Current: 60 mA * Low Leakage Current in Shutdown Mode: <1 A * VREF = +2.85 V (+2.7 V Min Over Temp.) * Optimized for a 50 System * Surface Mount Package * CDMA 1XRTT, 1xEV-DO Compliant * Pinout Enables Easy Phone Board Migration From 4 mm x 4 mm Package APPLICATIONS * Single Mode CDMA Wireless Handsets * Dual Mode AMPS/CDMA Wireless Handsets M9 Package 8 Pin 3 mm x 3 mm x 1 mm Surface Mount Module PRODUCT DESCRIPTION The AWT6301 meets the increasing demands for higher efficiency and linearity in AMPS/CDMA 1X handsets, while reducing pcb area by 44%. The package pinout was chosen to enable handset manufacturers to switch from a 4mm x 4mm PA module with very few layout changes to the phone board. The device is manufactured on an advanced InGaP HBT MMIC technology offering state-of-the- art reliability, temperature stability, and ruggedness. Selectable bias modes that optimize efficiency for different output power levels, and a shutdown mode with low leakage current, serve to increase handset talk and standby time. The self contained 3mm x 3mm surface mount package incorporates matching networks optimized for output power, efficiency and linearity in a 50 system. GND at slug (pad) VREF 8 GND VMODE 2 7 RFOUT RFIN 3 6 GND VCC1 4 5 VCC2 1 Bias Control Figure 1: Block Diagram 05/2005 AWT6301 GND VREF 1 8 GND VMODE 2 7 RFOUT RFIN 3 6 GND VCC1 4 5 VCC2 GND Figure 2: Pinout (X-ray Top View) Table 1: Pin Description 2 PIN NAME DESCRIPTION 1 VREF Reference Voltage 2 VMODE Mode Control 3 RFIN RF Input 4 V CC1 Supply Voltage 5 V CC2 Supply Voltage 6 GND Ground 7 RFOUT RF Output 8 GND Ground PRELIMINARY DATA SHEET - Rev 1.2 05/2005 AWT6301 ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PAR AME T E R MIN M AX U N IT Supply Voltage (VCC ) Wi th RF Dri ve DC Only 0 0 +5 +8 V Mode Control Voltage (VMODE) 0 +3.5 V Reference Voltage (VREF) 0 +3.5 V RF Input Power (PIN) - +10 dBm -40 +150 C Storage Temperature (TSTG) Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges PARAMETER MIN TYP MAX UNIT COMMENTS Operating Frequency (f) 824 - 849 MHz Supply Voltage (VCC) +3.2 +3.4 +4.2 V Reference Voltage (VREF) +2.7 0 +2.85 - +3.1 +0.5 V PA "on" PA "shut down" Mode Control Voltage (VMODE) +2.5 0 +2.8 - +3.1 +0.5 V Low Bias Mode High Bias Mode RF Output Power (POUT) 30.5(1) 27.5(1) 31.0 28.0 - dB m Case Temperature (TC) -30 - +85 C AMPS CDMA The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1) For operation at TC = +85 C and VCC = +3.2 V, POUT is derated by 0.5 dB. PRELIMINARY DATA SHEET - Rev 1.2 05/2005 3 AWT6301 Table 4: Electrical Specifications - AMPS Operation (TC = +25 C, VCC = +3.4 V, VREF = +2.85 V, VMODE = 0 V, POUT = +31 dBm, 50 system) PARAMETER MIN TYP MAX UNIT 24 26.5 30 dB - 0.3 1.0 dB 50 53 - % Quiescent Current (Icq) - 120 145 mA VMODE = 0 V, High Bias Reference Current - 5.0 8 mA through VREF pin Leakage Current - <1 5 mA VCC = +4.2 V, VREF = 0 V, VMODE = 0 V Noise in Receive Band - -134 -132 dBm/Hz Harmonics 2fo 3fo, 4fo - -35 -50 -30 -30 dB c Input Impedance - - 2:1 VSWR Gain Gain Variation Power-Added Efficiency (1) Spurious Output Level (all spurious outputs) Load mismatch stress with no permanent degradation or failure - - -65 dB c 10:1 - - VSWR Notes: (1) PAE limit applies at 824 MHz. 4 PRELIMINARY DATA SHEET - Rev 1.2 05/2005 COMMENTS 869 MHz to 894 MHz POUT < +31 dBm In-band Load VSWR < 5:1 Out-of-band Load VSWR < 10:1 Applies over all operating ranges Applies over all operating ranges AWT6301 Table 5: Electrical Specifications - CDMA Operation (TC = +25 C, VCC = +3.4 V, VREF = +2.85 V, 50 system) PARAMETER MIN TYP MAX UNIT COMMENTS 25 24 27.5 26.2 30 28 dB POUT = +28 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.85 V Adjacent Channel Power at 6885 kHz offset (1) Primary Channel BW = 1.23 MHZ Adjacent Channel BW = 30 kHz - -49.5 -56 -47 -47 dB c POUT = +28 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.85 V Adjacent Channel Power at 61.98 MHz offset (1) Primary Channel BW = 1.23 MHZ Adjacent Channel BW = 30 kHz - -59.5 -65 -57 -57 dB c POUT = +28 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.85 V 37 8 39 8.8 - % POUT = +28 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.85 V Quiescent Current (Icq) - 62 70 mA VMODE = +2.85 V, Low Bias Reference Current - 5 8 mA through VREF pin Mode Control Current - 0.35 1.0 mA through VMODE pin Leakage Current - <1 5 mA VCC = +4.2 V, VREF = 0 V, VMODE = 0 V Noise in Receive Band - -135 -133 dBm/Hz Harmonics 2fo 3fo, 4fo - -35 -50 -30 -30 dB c Input Impedance - - 2:1 VSWR Gain Power-Added Efficiency (1) - - -65 dB c POUT < +28 dBm In-band Load VSWR < 5:1 Out-of-band Load VSWR < 10:1 Applies over all operating ranges 10:1 - - VSWR Applies over all operating ranges Spurious Output Level (all spurious outputs) Load mismatch stress with no permanent degradation or failure 869 MHz to 894 MHz Notes: (1) PAE and ACP limit applies at 824 MHz. PRELIMINARY DATA SHEET - Rev 1.2 05/2005 5 AWT6301 APPLICATION INFORMATION To ensure proper performance, refer to all related Application Notes on the ANADIGICS web site: http://www.anadigics.com Shutdown Mode The power amplifier may be placed in a shutdown mode by applying a logic low levels (see Operating Ranges table) to both the VREF and VMODE voltages. Bias Modes The power amplifier may be placed in either a Low Bias mode or a High Bias mode by applying the appropriate logic level (see Operating Ranges table) to the VMODE voltage. The Bias Control table lists the recommended modes of operation for various applications. Table 6: Bias Control P OU T LEVELS B IAS MOD E V R EF V MOD E (all) High +2.85 V 0V CDMA - low power <+16 dBm Low +2.85 V +2.85 V CDMA - high power >+16 dBm High +2.85 V 0V - Shutdown 0V 0V AP P L IC AT ION AMPS Shutdown 6 PRELIMINARY DATA SHEET - Rev 1.2 05/2005 AWT6301 PACKAGE OUTLINE Figure 3: M9 Package Outline - 8 Pin 3 mm x 3 mm x 1 mm Surface Mount Module Figure 4: Branding Specification PRELIMINARY DATA SHEET - Rev 1.2 05/2005 7 AWT6301 COMPONENT PACKAGING Figure 5: Tape & Reel Packaging Table 7: Tape & Reel Dimensions 8 PACKAGE TYPE TAPE WIDTH POCKET PITCH REEL CAPACITY MAX REEL DIA 3 mm x 3 mm x 1 mm 12 mm 4 mm 2500 7" PRELIMINARY DATA SHEET - Rev 1.2 05/2005 AWT6301 NOTES PRELIMINARY DATA SHEET - Rev 1.2 05/2005 9 AWT6301 NOTES 10 PRELIMINARY DATA SHEET - Rev 1.2 05/2005 AWT6301 NOTES PRELIMINARY DATA SHEET - Rev 1.2 05/2005 11 AWT6301 ORDERING INFORMATION ORDER NUMBER AWT6301M9Q7 TEMPERATURE RANGE PACKAGE DESCRIPTION COMPONENT PACKAGING -30 C to +85 C 8 Pi n 3 mm x 3 mm x 1 mm Surface Mount Module 235 oC MSL-4 Tape and Reel, 2500 pieces per Reel ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: Mktg@anadigics.com IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product's formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. WARNING ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 12 PRELIMINARY DATA SHEET - Rev 1.2 05/2005