Series 115 (R) Commercial 3/4" (19mm) Diameter, 2 watt Wirewound Variable Resistor Features * Fully enclosed construction * Four mounting styles * Long rotational life * Optional grounded or insulated rotor construction * Incorporated fixed resistor available * Available with nylon shaft * Interchangeable mounting with CTS series 110 preset potentiometers * RoHS compliant Electrical and Mechanical Specifications Resistance Range 1 ohm through 20K ohms (linear taper) Resistance Tolerance Standard: 20% Special: 5% or 10% Power Rating, Watts 2 watts @ 55C derated to no load @ 105C mounted on steel panel 1.5 watts @ 55C derated to no load @ 105C, mounted on bakelite panel Voltage Rating Terminals to case (insulated types only) High pot test, one minute -- 900 VAC Operating maximum -- 500 VDC Across end terminals Determined by resistance value and wattage rating Resistance Taper Standard: Linear taper only Taps Available None Incorporated Fixed Resistor A fixed resistor can be incorporated in the Series 115 at the end of CW or CCW rotation to a minimum of 15% of the total resistance value. The rotation is shortened by an amount proportional to the ratio of the fixed resistor to the total resistance value. Angle of Rotation Tatol Rotation: 270 5 1-3 CTS Electronic Components Resistor Adjustment Standard: Cross slot provided in rotor for screwdriver adjustment. Special: Molded nylon, screwdriver-slotted shafts which are integral with rotor are available in many lengths in increments of 1/8" (3.2mm) up to a maximum of 2" (50.8mm).Consults with the factory Mounting Types Available Printed circuit mounted: Type 115 P Twist tab mounted: Type 115 T Snap-in mounted: Type 116 E Type 117 R Rivet ear mounted: Terminal Information Grounded Construction -- The grounded construction is supplied without a center terminal and the contactor is connected to the case. This construction can be furnished with one end terminal at either end of the resistance element or with terminals at both ends of the element. Insulated Construction -- The contactor is insulated from the base and connected to the center terminal on the insulated construction. This construction can be supplied with the center terminal and one end terminal at either end of the resistance element or with the center terminal and terminals at both ends of the resistance element. Rotational Torque 1/2 to 10 in-oz. (36 - 720 gf-cm) Stop Strength 4 in-oz. (4.6 Kgf-cm) (c) 2006 CTS Corporation. All rights reserved. Information subject to change. 9/30/06 www.ctscorp.com Type 115P, P.C. Mounted mm DIMENSION: INCH CENTER TERMINAL SUPPLIED WITH INSULATED CONTACT ARM CONSTRUCTION. OMITTED ON GROUNDED CONTACT ARM CONSTRUCTION. 45 1.6 .063 END C.C.W ROT. OPTIONAL TERMINAL POSITION PARALLEL TO MTG. SURFACE 10.290.05 .405.002 TERMINALS 1.98X0.41 .078X.016 7.95 .313 SUGGESTED PANEL PIERCING 20.570.05 .810.002 45 END C.W ROT. 1.27 MIN. .050 1.27 MIN. .050 2.790.05 .110.002 1.4 .055 2.39 .094 6.35 9.40.05 .370.002 .250 1.4 .055 1.52 .060 270 ROT. 6.73 .265 2 CROSS SLOTS 1.57X4.72 .062X.186 19.84 .781 1.6 .063 9.78 .385 16.51 .650 2.790.05 .110.002 40 40 1.6 .063 18.24 6.73 .718 5.16 .265 8.33 .328 6.76 .203 .266 11.51 9.78 .453 .385 MOUNTING SURFACE Type 115T, Twist Tab Mounted DIMENSION: mm INCH CENTER TERMINAL SUPPLIED WITH INSULATED CONTACT ARM CONSTRUCTION. OMITTED ON GROUNDED CONTACT ARM CONSTRUCTION. 45 45 1.6 .063 END C.C.W ROT. END C.W ROT. OPTIONAL TERMINAL POSITION PARALLEL TO MTG. SURFACE 7.95 .313 10.41 .410 1.57 .062 TERMINALS 1.98X0.41 .078X.016 10.41 .410 1.57 .062 2.08 .082 4.17 .164 3.96 .156 6.35 19.84 .250 .781 9.40.05 .370.002 1.52 .060 40 270 ROT. 5.56 .219 2 CROSS SLOTS 1.57X4.72 .062X.186 23.010.38 .906.015 10.31 .406 1.4 .055 1.6 .063 2.790.05 .110.002 40 1.6 .063 7.92 .312 15.88 .625 6.35 .250 18.26 3.96 .156 5.56 .219 .719 11.91 10.31 .469 .406 7.92 .312 MOUNTING SURFACE PRINTED CIRCUIT BOARD Type 116E,Snap-in Ear Mounted DIMENSION: mm INCH CENTER TERMINAL SUPPLIED WITH INSULATED CONTACT ARM CONSTRUCTION. OMITTED ON GROUNDED CONTACT ARM CONSTRUCTION. 45 20.220.05 .796.002 45 1.6 .063 END C.C.W ROT. END C.W ROT. OPTIONAL TERMINAL POSITION PARALLEL TO MTG. SURFACE 10.110.05 .398.002 TERMINALS 1.98X0.41 .078X.016 7.95 .313 1.57 .062 2.39 .094 MIN. 9.40.05 .370.002 1.52 .060 6.35 .250 2 CROSS SLOTS 1.57X4.72 .062X.186 6.35 .250 9.93 .391 16.28 .641 40 2.790.05 .110.002 2.790.05 .110.002 1.6 .063 6.76 .266 4.78 6.35 .188 .250 8.33 .328 MOUNTING SURFACE .719 2- 3 CTS Electronic Components 1.4 .055 SUGGESTED PANEL PIERCING 1.6 .063 8.33 .328 18.26 MIN. 1.4 .055 40 270 ROT. 21.59 .850 1.57 .062 11.51 9.93 .453 .391 PRINTED CIRCUIT BOARD (c) 2006 CTS Corporation. All rights reserved. Information subject to change. 9/30/06 www.ctscorp.com Type 117R, Rivet Ear Mounted DIMENSION: mm INCH CENTER TERMINAL SUPPLIED WITH INSULATED CONTACT ARM CONSTRUCTION. OMITTED ON GROUNDED CONTACT ARM CONSTRUCTION. 45 45 1.57 .062 END C.C.W ROT. END C.W ROT. 25.40.05 1.000.002 1 7.92 .312 3.450.08 DIA. .136.003 12.70.05 2 3 3.450.08 DIA. .136.003 R8.64 .340R. 2HOLES TERMINALS 1.98 .078 WIDE X 0.36 .014 270 ROT. 9.93 .391 2 CROSS SLOTS 1.57X4.72 .062X.186 25.4 1.000 6.35 .250 40 19.84 .781 40 DIA. OF HLS. TO SUIT TERMINAL CLEARANCE. (IF TERMINALS PENETRATE CHASSIS.) 1.57 .062 18.26 .719 31.75 2 HLS. .500.002 OPTIONAL PC TERMINAL POSITION PERPENDICULAR TO MTG. SURFACE 1.250 1.57 .062 6.76 .266 8.33 .328 11.51 9.93 .453 .391 MTG. SURFACE MOUNTING PANEL Ordering Information 115 G P 3 00 SERIES MOUNTING DESIGNATION MOUNTING STYLE SHAFT LENGTH 115 - PC MOUNT OR TWIST TAB 116 - EAR 117 - RIVET EAR T - TWIST TAB P - PC E - EAR R - RIVET EAR 00 - NO SHAFT TERMINAL STYLE J - INSULATED CONSTRUCTION G - GROUNDED CONSTRUCTION 3-3 CTS Electronic Components LOCATING LUG 3 - NONE SHAFT TRIM C - CROSS SLOT C 103 B RESISTANCE CODE EXAMPLES CODE 5A0 500 101 501 102 252 502 103 203 RESISTANCE 5 OHMS 50 100 500 1K 2.5K 5K 10K 20K (c) 2006 CTS Corporation. All rights reserved. Information subject to change. 1 TAPER 1 - LINEAR RESIST TOLERANCE A - 10% B - 20% D - 5% 9/30/06 www.ctscorp.com