NBB 8-18GM60-A2-V1 - PEPPERL+FUCHS

Inductive sensor NBB8-18GM60-A2-V1-3G-3D

Release date: 2011-07-19 11:21 Date of issue: 2011-07-19 212062_eng.xml

Germany: +49 621 776-4411

Subject to modifications without notice

Pepperl+Fuchs Group

fa-info@pepperl-fuchs.comwww.pepperl-fuchs.com

USA: +1 330 486 0001

fa-info@us.pepperl-fuchs.com

Singapore: +65 6779 9091

fa-info@sg.pepperl-fuchs.com

Dimensions

Technical Data

General specifications

Switching element function PNP NO/NC

Rated operating distance sn8 mm

Installation embeddable

Output polarity DC

Assured operating distance sa0 ... 6.48 mm

Reduction factor rAl 0.45

Reduction factor rCu 0.4

Reduction factor r303 0.7

Nominal ratings

Operating voltage UB10 ... 30 V DC

Switching frequency f 0 ... 500 Hz

Hysteresis H typ. 5 %

Reverse polarity protected reverse polarity protected

Short-circuit protection pulsing

Voltage drop Ud≤ 3 V

Operating current IL0 ... 200 mA

Off-state current Ir0 ... 0.5 mA typ. 0.1 µA at 25 °C

No-load supply current I0≤ 25 mA

Indication of the switching state LED, yellow

Ambient conditions

Ambient temperature -25 ... 70 °C (-13 ... 158 °F)

Mechanical specifications

Connection type Device connector M12 x 1 , 4-pin

Housing material brass, nickel-plated

Sensing face PBT

Protection degree IP67

General information

Use in the hazardous area see instruction manuals

Category 3G; 3D

Compliance with standards and directives

Standard conformity

Standards EN 60947-5-2:2007

IEC 60947-5-2:2007

Approvals and certificates

UL approval cULus Listed, General Purpose

CSA approval cCSAus Listed, General Purpose

CCC approval Products with a maximum operating voltage of ≤36 V do not bear a

CCC marking because they do not require approval.

M18x1

M12x1

LED

Model Number

NBB8-18GM60-A2-V1-3G-3D

Features

• Increased operating distance

• 8 mm embeddable

• ATEX-approval for zone 2 and zone 22

Connection

Pinout

Accessories

BF 18

Mounting flange, 18 mm

EXG-18

Quick mounting bracket with dead stop

V1-G

4-pin, M12 female field-attachable connector

V1-W

4-pin, M12 female field-attachable connector

1L+

L-

1 BN

2 WH

3 BU

4 BK

Wire colors in accordance with EN 60947-5-2

(brown)

(white)

(blue)

(black)

Inductive sensor NBB8-18GM60-A2-V1-3G-3D

Release date: 2011-07-19 11:21 Date of issue: 2011-07-19 212062_eng.xml

Germany: +49 621 776-4411

Subject to modifications without notice

Pepperl+Fuchs Group

fa-info@pepperl-fuchs.comwww.pepperl-fuchs.com

USA: +1 330 486 0001

fa-info@us.pepperl-fuchs.com

Singapore: +65 6779 9091

fa-info@sg.pepperl-fuchs.com

ATEX 3G (nA)

Instruction Manual electrical apparatus for hazardous areas

Device category 3G (nA) for use in hazardous areas with gas, vapour and mist

Directive conformity 94/9/EG

Standard conformity EN 60079-0:2006, EN 60079-15:2005

Ignition protection category "n"

Use is restricted to the following stated conditions

CE symbol

Ex-identification ¬ II 3G Ex nA IIC T6 X

The Ex-significant identification is on the enclosed adhesive label

General The apparatus has to be operated according to the appropriate data in the data sheet and in this instruction manual.

The data stated in the data sheet are restricted by this operating instruction! The special conditions must be observed!

Installation, Comissioning Laws and/or regulations and standards governing the use or intended usage goal must be observed.

The adhesive label provided must be affixed in the immediate vicinity of the sensor! The surface to which the label is applied

must be clean, flat and free from grease!

The affixed adhesive label must be readable and durable, taking account of the possibility of chemical corrosion!

Maintenance No changes can be made to apparatus, which are operated in hazardous areas.

Repairs to these apparatus are not possible.

Special conditions

Maximum operating current IL The maximum permissible load current must be restricted to the values given in the following list. High load currents and load

short-circuits are not permitted.

Maximum operating voltage UBmax The maximum permissible operating voltage UB max is restricted to the values in the following list. Tolerances are not per-

missible.

Maximum permissible ambient tempera-

ture TUmax

dependant of the load current IL and the max. operating voltage UBmax.

Information can be taken from the following list.

at UBmax=30 V, IL=200 mA 45 °C (113 °F)

at UBmax=30 V, IL=100 mA 50 °C (122 °F)

at UBmax=30 V, IL=50 mA 50 °C (122 °F)

Plug connector The plug connector must not be disconnected under voltage. The proximity switch is marked as follows: “DO NOT DISCON-

NECT UNDER VOLTAGE!” When the plug connector is disconnected the ingress of dirt into the inner areas (i.e. the areas,

which are not accessible in the plugged-in condition) must be prevented.

Protection from mechanical danger The sensor must not be exposed to ANY FORM of mechanical danger.

Protection from UV light The sensor and the connection cable must be protected from damaging UV-radiation. This can be achieved when the sensor

is used in internal areas.

Electrostatic charging Electrostatic charges must be avoided on the mechanical housing components. Dangerous electrostatic charges on the

mechanical housing components can be avoided by incorporating these in the equipotential bonding.

Inductive sensor NBB8-18GM60-A2-V1-3G-3D

Release date: 2011-07-19 11:21 Date of issue: 2011-07-19 212062_eng.xml

Germany: +49 621 776-4411

Subject to modifications without notice

Pepperl+Fuchs Group

fa-info@pepperl-fuchs.comwww.pepperl-fuchs.com

USA: +1 330 486 0001

fa-info@us.pepperl-fuchs.com

Singapore: +65 6779 9091

fa-info@sg.pepperl-fuchs.com

ATEX 3D (tD)

Note This instruction is only valid for products according to EN 61241-0:2006 and EN 61241-1:2004

Note the ex-marking on the sensor or on the enclosed adhesive label

Instruction Manual electrical apparatus for hazardous areas

Device category 3D for use in hazardous areas with combustible dust

Directive conformity 94/9/EG

Standard conformity EN 61241-0:2006, EN 61241-1:2004

Protection via housing "tD"

Use is restricted to the following stated conditions

CE symbol

Ex-identification ¬ II 3D Ex tD A22 IP67 T80°C X

The Ex-significant identification is on the enclosed adhesive label

General The apparatus has to be operated according to the appropriate data in the data sheet and in this instruction manual.

The maximum surface temperature has been determined in accordance with method A without a dust layer on the equip-

ment.

The data stated in the data sheet are restricted by this operating instruction!

The special conditions must be adhered to!

Installation, Comissioning Laws and/or regulations and standards governing the use or intended usage goal must be observed.

The adhesive label provided must be affixed in the immediate vicinity of the sensor! The surface to which the label is applied

must be clean, flat and free from grease!

The affixed adhesive label must be readable and durable, taking account of the possibility of chemical corrosion!

Maintenance No changes can be made to apparatus, which are operated in hazardous areas.

Repairs to these apparatus are not possible.

Special conditions

Maximum operating current IL The maximum permissible load current must be restricted to the values given in the following list.

High load currents and load short-circuits are not permitted.

Maximum operating voltage UBmax The maximum permissible operating voltage UBmax must be restricted to the values given in the following list. Tolerances

are not permitted.

Maximum permissible ambient tempera-

ture TUmax

dependant of the load current IL and the max. operating voltage UBmax.

Information can be taken from the following list.

at UBmax=30 V, IL=200 mA 45 °C (113 °F)

at UBmax=30 V, IL=100 mA 50 °C (122 °F)

at UBmax=30 V, IL=50 mA 50 °C (122 °F)

Plug connector The plug connector must not be withdrawn under voltage. The proximity switch is identified as follows: "WARNING - DO NOT

SEPARATE WHEN ENERGIZED". With the plug connector disconnected, soiling of the internal area must be prevented.(i.e.

the area that is inaccessible when the connector is inserted)

The plug connection can only be separated using a tool. This is achieved by using the locking protection V1-Clip (Mounting

accessory from Pepperl + Fuchs).

Protection from mechanical danger The sensor must not be exposed to ANY FORM of mechanical danger.

Protection from UV light The sensor and the connection cable must be protected from damaging UV-radiation. This can be achieved when the sensor

is used in internal areas.

Electrostatic charging Electrostatic charges must be avoided on the mechanical housing components. Dangerous electrostatic charges on the

mechanical housing components can be avoided by incorporating these in the equipotential bonding.