Datasheet AS1371 4 0 0 m A , L o w I n p u t Vol t a g e , L o w Q u i e s c e n t C u r r e n t L D O 1 General Description 2 Key Features The AS1371 low input voltage, positive voltage regulator is designed to deliver up to 400mA while consuming typically only 15A of quiescent current. The device operates from input voltages of 1.2V to 3.6V, and is available in fixed output voltages between 0.6V and 3.3V (programmable in 50mV steps). Ultra-Low Dropout Voltage: 20mV @ 100mA load Operation at the full 400mA load current is dependent upon the maximum power dissipation available from package and environment. Output Voltage Accuracy: 1% The low input voltage and ultra-low dropout voltage (20mV @ 100mA load and 80mV @ 400mA load) supports single primary cell operation in small applications, when operated with minimum inputto-output voltage differentials. In addition, the regulator provides a power management life extension by operating from pre-existing 1.8V and 2.5V outputs to provide low output voltages for new generation portable processor cores. Low Quiescent Current: 50A @ max load Operating Input Voltage Range: 1.2V to 3.6V Output Voltages: 0.6V to 3.3V in 50mV steps Max. Output Current: 400mA Low Shutdown Current: 10nA Integrated Overtemperature/Overcurrent Protection Under-Voltage Lockout Feature Chip Enable Input Power-OK and Low Battery Detection Sense Input Option The device features stable output voltage with ceramic capacitors down to a value of 1F, strict output voltage regulation tolerances (1%), and good line- and load-regulation. Minimal External Components Required Operating Temperature Range: -40C to +85C The AS1371 is available in a 6-pin 2x2 TDFN package and is qualified for -40C to +85C operation. 6-pin 2x2 TDFN Package 3 Applications The devices are ideal for powering cordless and mobile phones, MP3 players, CD and DVD players, PDAs, hand-held computers, digital cameras, and any other hand-held and/or battery-powered device. Figure 1. AS1371 - Typical Application Diagram Input 1.2V to 3.6V CIN 1F ON OFF AS1371 EN 100k COUT 1F POK GND www.austriamicrosystems.com/LDOs/AS1371 Output 0.6V to 3.3V OUT IN SENSE Revision 1.6 1 - 17 AS1371 Datasheet - P i n A s s i g n m e n t s 4 Pin Assignments Figure 2. Pin Assignments (Top View) IN 1 POK 2 EN 3 AS1371 Exposed Pad 6 OUT 5 SENSE 4 GND 4.1 Pin Descriptions Table 1. Pin Descriptions Pin Number Pin Name Description LDO Input. Input voltage range: 1.2V to 3.6V. Bypass with 1F to GND. 1 IN 2 POK 3 EN 4 GND Ground. This pin also functions as a heat sink. Solder it to a large pad or to the circuit-board ground plane to maximize power dissipation. 5 SENSE Sense Input. Represents the input for the Power-OK behavior. If connected to GND the POK output is related to OUT. 6 OUT LDO Output. Bypass with 1F to GND. Exposed Pad GND Exposed Pad. This pin also functions as a heat sink. Solder it to a large pad or to the circuitboard ground plane to maximize power dissipation. Internally it is connected GND. www.austriamicrosystems.com/LDOs/AS1371 Power-OK Output. Active-low, open-drain output indicates an out-of-regulation condition. Connect a 100k pull-up resistor to pin OUT for logic levels. Leave this pin unconnected if the Power-OK feature is not used. Active-High Enable Input. A logic low reduces the supply current to < 1A. Connect to pin IN for normal operation. Revision 1.6 2 - 17 AS1371 Datasheet - A b s o l u t e M a x i m u m R a t i n g s 5 Absolute Maximum Ratings Stresses beyond those listed in Table 2 may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in Section 6 Electrical Characteristics on page 4 is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 2. Absolute Maximum Ratings Parameter Min Max Units Notes IN and EN to GND -0.3 +5.0 V POK and OUT to GND -0.3 VIN + 0.3 V Input Current (latch-up immunity) -100 100 mA Norm: JEDEC 78 1000 V Norm: MIL 883 E method 3015 C/W Junction-to-ambient thermal resistance is very dependent on application and board-layout. In situations where high maximum power dissipation exists, special attention must be paid to thermal dissipation during board design. Electrical Parameters Electrostatic Discharge Electrostatic Discharge HBM Temperature Ranges and Storage Conditions Thermal Resistance JA +78.6 Junction Temperature Storage Temperature Range -55 Package Body Temperature Humidity non-condensing Moisture Sensitive Level www.austriamicrosystems.com/LDOs/AS1371 5 +125 C +125 C +260 C 85 % 1 The reflow peak soldering temperature (body temperature) specified is in accordance with IPC/ JEDEC J-STD-020"Moisture/Reflow Sensitivity Classification for Non-Hermetic Solid State Surface Mount Devices". The lead finish for Pb-free leaded packages is matte tin (100% Sn). Represents a maximum floor life time of unlimited Revision 1.6 3 - 17 AS1371 Datasheet - E l e c t r i c a l C h a r a c t e r i s t i c s 6 Electrical Characteristics VIN = VOUT (Nominal) + 0.5V, EN = IN, CIN = COUT = 1F, TAMB = -40C to +85C (unless otherwise specified). Typical Values are at TAMB = +25C. Table 3. Electrical Characteristics Symbol Parameter Conditions TAMB Operating Temperature Range VIN Input Voltage VOUT Output Voltage Min Available in 50mV steps, see Ordering Information on page 16 TAMB = +25C, IOUT = 1mA, 1V Output Voltage Accuracy VOUT > TAMB = -40 to +85C, IOUT = 1mA, VOUT > 1V Typ Max Units -40 +85 C 1.2 3.6 V 0.6 3.3 V -2 +2 -3.5 +3.5 % IOUT Maximum Output Current 400 mA ILIM Current Limit IQ Quiescent Current VIN-VOUT Dropout Voltage VLNR Line Regulation IOUT = 1mA VLDR Load Regulation IOUT = 1mA to 400mA 0.003 %/mA Output Voltage Noise f = 10Hz to 100kHz, IOUT = 10mA 100 VRMS PSRR Output Voltage AC Power-Supply Rejection Ratio f = 10kHz, IOUT = 10mA 50 dB COUT Output Capacitor 1 F 650 1 IOUT = 0mA 15 IOUT = 400mA 50 IOUT = 100mA 20 IOUT = 400mA 80 Load Capacitor Range -15 0.47 0 ESR Load mA 20 50 +15 A mV mV 500 m 90 150 s EN = GND, TAMB = +25C 0.01 1 EN = GND, TAMB = +85C 0.04 2 Shutdown tON Exit Delay from Shutdown IOFF Enable Supply Current VIH 3,4 1.0 Enable Input Threshold VIL IEN 0.4 Enable Input Bias Current EN = IN or GND, TAMB = +25C 0.03 EN = IN or GND, TAMB = +85C 0.2 100 A V nA Power-OK Output 5 VPOK Power-OK Voltage Threshold VSENSE Power-OK Sense Voltage Threshold VOL POK Output Voltage Low www.austriamicrosystems.com/LDOs/AS1371 SENSE = GND, VPOKFALLING 90 SENSE = GND, Hysteresis VOUT 1.05V, VSENSE falling Hysteresis ISINK = 100A Revision 1.6 94 97 1 650 800 950 50 0.4 % VOUT mV V 4 - 17 AS1371 Datasheet - E l e c t r i c a l C h a r a c t e r i s t i c s Table 3. Electrical Characteristics Symbol Parameter Conditions IPOK POK Output Leakage Current 0 VPOK3.6V, TAMB = +25C, VOUT in regulation Min Typ Max Units 1 A Thermal Protection 1. 2. 3. 4. 5. TSHDN Thermal Shutdown Temperature 150 C TSHDN Thermal Shutdown Hysteresis 15 C Dropout voltage = VIN - VOUT when VOUT is 100mV < VOUT for VIN = VOUT(NOM) +0.5V (applies only to output voltages 1.3V). The rise and fall time of the shutdown signal must not exceed 1ms. The delay time is defined as time required to set VOUT to 95% of its final nominal value. Guaranteed by design. The functionality is proven by production test, limits are guaranteed by design. Note: All limits are guaranteed. The parameters with min and max values are guaranteed with production tests or SQC (Statistical Quality Control) methods. www.austriamicrosystems.com/LDOs/AS1371 Revision 1.6 5 - 17 AS1371 Datasheet - Ty p i c a l O p e r a t i n g C h a r a c t e r i s t i c s 7 Typical Operating Characteristics VOUT = 1.8V, VIN = 2.3V, IOUT = 1mA, TAMB = +25C (unless otherwise specified). Figure 4. Line Regulation, VOUT vs. VIN 1.9 1.9 1.875 1.875 1.85 1.85 Output Voltage (V) Output Voltage (V) Figure 3. Output Voltage vs. Temperature 1.825 1.8 1.775 1.75 no load 1.725 1.825 1.8 1.775 1.75 - 40C + 25C 1.725 Iout = 10mA 1.7 -40 + 85C 1.7 -20 0 20 40 60 80 2.2 2.4 2.6 Temperature (C) 100 1.875 90 1.85 1.825 1.8 1.775 1.75 - 40C + 25C 3.2 3.4 3.6 3.4 3.6 no load Iout = 100mA 80 Iout = 400mA 70 60 50 40 30 20 10 + 85C 1.7 0 0 50 2.2 100 150 200 250 300 350 400 2.4 Output Current (mA) 2.6 2.8 3 3.2 Input Voltage (V) Figure 7. POK Voltage Threshold vs. Temperature Figure 8. Dropout Voltage vs. Output Current 100 100 99 90 98 80 Dropout Voltage (mV) Output Voltage (% of Voutnom) 3 Figure 6. Quiescent Current vs. Input Voltage 1.9 Quiescent Current (A) Output Voltage (V) Figure 5. Load Regulation, VOUT vs. IOUT 1.725 2.8 Input Voltage (V) 97 96 95 94 93 70 60 50 40 30 92 POK rising 20 - 40C + 25C 91 POK f alling 10 + 85C 90 -40 0 -20 0 20 40 60 80 0 Temperature (C) www.austriamicrosystems.com/LDOs/AS1371 50 100 150 200 250 300 350 400 Output Current (mA) Revision 1.6 6 - 17 AS1371 Datasheet - Ty p i c a l O p e r a t i n g C h a r a c t e r i s t i c s 500mV/DIV IOUT 50mA/Div Figure 10. Load Transient Response; IOUT = 0mA to 100mA VOUT VOUT 500mV/DIV VIN 500mV/Div Figure 9. Line Transient Response; VIN = 2.3V to 2.8V, No load 100ms/Div 100ms/Div www.austriamicrosystems.com/LDOs/AS1371 1V/Div EN VOUT 20s/Div 500mV/DIV 1V/Div VOUT 500mV/DIV Figure 12. Turn OFF EN Figure 11. Turn ON 20s/Div Revision 1.6 7 - 17 AS1371 Datasheet - D e t a i l e d D e s c r i p t i o n 8 Detailed Description The AS1371 is a low-dropout, low-quiescent-current linear regulator intended for LDO regulator applications where output current load requirements range from no load to 400mA. All devices come with fixed output voltage from 0.6V to 3.3V. See Ordering Information on page 16. The AS1371 also features a Power-OK output to indicate when the output is within 10% (max) of final value when the Enable pin is grounded. When the Enable pin is raised above ground, the POK comparator inputs are switched to change the functionality. The comparator reference is now 800mV and the Enable pin becomes an uncommitted comparator input. See Power-OK and Low-Battery-Detect Functionality (page 9) for setting resistor values when monitoring other voltages (i.e. VOUT). Shutdown current for the whole regulator is typically 10nA. The device features integrated short-circuit and over current protection. Under-Voltage lockout prevents erratic operation when the input voltage is slowly decaying (e.g. in a battery powered application). Thermal Protection shuts down the device when die temperature reaches 150C. This is a useful protection when the device is under sustained short circuit conditions. Figure 13 shows the block diagram of the AS1371. It identifies the basics of a series linear regulator employing a P-Channel MOSFET as the control element. A stable voltage reference (REF in Figure 13) is compared with an attenuated sample of the output voltage. Any difference between the two voltages (reference and sample) creates an output from the error amplifier that drives the series control element to reduce the difference to a minimum. The error amplifier incorporates additional buffering to drive the relatively large gate capacitance of the series pass Pchannel MOSFET, especially under transient conditions, when additional drive current is required. Input supply variations are absorbed by the series element, and output voltage variations with loading are absorbed by the low output impedance of the regulator. Figure 13. AS1371 - Block Diagram QPOWER OUT VIN Thermal Overload Protection Shutdown Control Logic EN SENSE + + + Error Amplifier AS1371 POK TRIM - + - VREF 800mV + - + - 94% VREF 100mV + GND 8.1 Output Voltages Standard products are factory-set with output voltages from 0.6V to 3.3V. A two-digit suffix of the part number identifies the nominal output (see Ordering Information on page 16). Non-standard devices are available. For more information contact: http://www.austriamicrosystems.com/contact www.austriamicrosystems.com/LDOs/AS1371 Revision 1.6 8 - 17 AS1371 Datasheet - D e t a i l e d D e s c r i p t i o n 8.2 Power-OK and Low-Battery-Detect Functionality The AS1371's power-ok or low-battery-detect circuitry is built around an N-channel MOSFET. The circuitry monitors the voltage on pin SENSE and if the voltage goes out of regulation (e.g. during dropout, current limit or thermal shutdown) the pin POK goes low. The pin SENSE can be connected to a resistive-divider to monitor a particular definable voltage and compare it with an internal voltage reference. If the SENSE pin is connected to GND an internal resistive-divider is activated and connected to the output. Therefore, the Power-OK functionality can be realized with no additional external components. The Power-OK feature is not active during shutdown and provides a power-on-reset function that can operate down to VIN = 1.2V. A capacitor to GND may be added to generate a power-on-reset delay. To obtain a logic-level output, connect a pull-up resistor from pin POK to pin OUT. Larger values for this resistor will help to minimize current consumption; a 100k resistor is perfect for most applications (see Figure 1 on page 1). For the circuit shown in the left of Figure 14 on page 9, the input bias current into SENSE is very low, permitting large-value resistor-divider networks while maintaining accuracy. Place the resistor-divider network as close to the device as possible. Use a defined resistor for R2 and then calculate R1 as: V IN R 1 = R 2 ------------------ - 1 V SENSE (EQ 1) Where: VSENSE = 800mV 150mV. In case of the SENSE pin is connected to GND, an internal resistor-divider network is activated and compares the output voltage with a 94% (typ.) voltage threshold. For this particular Power-OK application, no external resistive components are necessary. Figure 14. Application Diagrams Input 1.2V to 3.6V CIN 1F ON / OFF R1 External Voltage Level Detection Internal Voltage Level Detection (Input Monitoring) (Output Monitoring) Output 0.6V to 3.3V OUT IN AS1371 EN GND RPU 100k Input 1.2V to 3.6V CIN 1F COUT 1F ON / OFF POK OUT IN GND SENSE RPU 100k AS1371 EN Output 0.6V to 3.3V COUT 1F POK SENSE R2 8.3 Current Limiting The AS1371 include current limiting circuitry to protect against short-circuit conditions. The circuitry monitors and controls the gate voltage of the P-channel MOSFET, limiting the output current to 400mA. The P-channel MOSFET output can be shorted to ground for an indefinite period of time without damaging the device. 8.4 Thermal-Overload Protection The devices are protected against thermal runaway conditions by the integrated thermal sensor circuitry. Thermal shutdown is an effective instrument to prevent die overheating since the power transistor is the principle heat source in the device. If the junction temperature exceeds 150C with 15C hysteresis, the thermal sensor starts the shutdown logic, at which point the P-channel MOSFET is switched off. After the device temperature has dropped by approximately 15C, the thermal sensor will turn the P-channel MOSFET on again. Note that this will be exhibited as a pulsed output under continuous thermal-overload conditions. www.austriamicrosystems.com/LDOs/AS1371 Revision 1.6 9 - 17 AS1371 Datasheet - A p p l i c a t i o n I n f o r m a t i o n 9 Application Information 9.1 Dropout Voltage Dropout is the input to output voltage difference, below which the linear regulator ceases to regulate. At this point, the output voltage change follows the input voltage change. Dropout voltage may be measured at different currents and, in particular at the regulator maximum one. From this is obtained the MOSFET maximum series resistance over temperature etc. More generally: V DROPOUT = I LOAD R SERIES (EQ 2) Dropout is probably the most important specification when the regulator is used in a battery application. The dropout performance of the regulator defines the useful "end of life" of the battery before replacement or re-charge is required. Figure 15. Graphical Representation of Dropout Voltage VIN VOUT VIN = VOUT(TYP) + 0.5V Dropout Voltage VOUT 100mV VIN VOUT VIN Figure 15 shows the variation of VOUT as VIN is varied for a certain load current. The practical value of dropout is the differential voltage (VOUTVIN) measured at the point where the LDO output voltage has fallen by 100mV below the nominal, fully regulated output value. The nominal regulated output voltage of the LDO is that obtained when there is 500mV (or greater) input-output voltage differential. 9.2 Efficiency Low quiescent current and low input-output voltage differential are important in battery applications amongst others, as the regulator efficiency is directly related to quiescent current and dropout voltage. Efficiency is given by: V I V IN I Q + I LOAD LOAD LOAD Efficiency = --------------------------------------- 100 % (EQ 3) Where: IQ = Quiescent current of LDO 9.3 Power Dissipation Maximum power dissipation (PD) of the LDO is the sum of the power dissipated by the internal series MOSFET and the quiescent current required to bias the internal voltage reference and the internal error amplifier, and is calculated as: PD MAX Seriespass = I LOAD MAX V IN MAX - V OUT MIN Watts (EQ 4) Internal power dissipation as a result of the bias current for the internal voltage reference and the error amplifier is calculated as: PD MAX Bias = V IN MAX I Q Watts (EQ 5) PD MAX Total = PD MAX Seriespass + PD MAX Bias Watts (EQ 6) Total LDO power dissipation is calculated as: www.austriamicrosystems.com/LDOs/AS1371 Revision 1.6 10 - 17 AS1371 Datasheet - A p p l i c a t i o n I n f o r m a t i o n 9.4 Junction Temperature Under all operating conditions, the maximum junction temperature should not be allowed to exceed 125C (unless the data sheet specifically allows). Limiting the maximum junction temperature requires knowledge of the heat path from junction to case (JCC/W fixed by the IC manufacturer), and adjustment of the case to ambient heat path (CAC/W) by manipulation of the PCB copper area adjacent to the IC position. Figure 16. Package Physical Arrangements TDFN Package Chip Package Bond Wire Lead Frame PCB Exposed Pad Figure 17. Steady State Heat Flow Equivalent Circuit Package TCC Junction TJC RJC PCB/Heatsink TSC RCS Ambient TAC RSA Chip Power Total Thermal Path Resistance: R JA = R JC + R CS + R SA (EQ 7) T J = PD MAX R JA + T AMB C (EQ 8) Junction Temperature (TJC) is determined by: www.austriamicrosystems.com/LDOs/AS1371 Revision 1.6 11 - 17 AS1371 Datasheet - A p p l i c a t i o n I n f o r m a t i o n 9.5 Explanation of Steady State Specifications 9.5.1 Line Regulation Line regulation is defined as the change in output voltage when the input (or line) voltage is changed by a known quantity. It is a measure of the regulator's ability to maintain a constant output voltage when the input voltage changes. Line regulation is a measure of the DC open loop gain of the error amplifier. More generally: V V IN OUT Line Regulation = ---------------- and is a pure number (EQ 9) In practise, line regulation is referred to the regulator output voltage in terms of % / VOUT. This is particularly useful when the same regulator is available with numerous output voltage trim options. V V IN 100 V OUT OUT Line Regulation = ---------------- ------------ % / V 9.5.2 (EQ 10) Load Regulation Load regulation is defined as the change of the output voltage when the load current is changed by a known quantity. It is a measure of the regulator's ability to maintain a constant output voltage when the load changes. Load regulation is a measure of the DC closed loop output resistance of the regulator. More generally: V I OUT OUT Load Regulation = ---------------- and is units of ohms () (EQ 11) In practise, load regulation is referred to the regulator output voltage in terms of % / mA. This is particularly useful when the same regulator is available with numerous output voltage trim options. V I OUT 100 V OUT OUT Load Regulation = ---------------- ---------------- % / mA 9.5.3 (EQ 12) Setting Accuracy Accuracy of the final output voltage is determined by the accuracy of the ratio of R1 and R2, the reference accuracy and the input offset voltage of the error amplifier. When the regulator is supplied pre-trimmed, the output voltage accuracy is fully defined in the output voltage specification. When the regulator has a SET or SENSE terminal, the output voltage may be adjusted externally. In this case, the tolerance of the external resistor network must be incorporated into the final accuracy calculation. Generally: R1 R1 V OUT = V SET V SET 1 + --------------------- R2 R2 (EQ 13) The reference tolerance is given both at 25C and over the full operating temperature range. 9.5.4 Total Accuracy Away from dropout, total steady state accuracy is the sum of setting accuracy, load regulation and line regulation. Generally: Total % Accuracy = Setting % Accuracy + Load Regulation % + Line Regulation % (EQ 14) 9.6 Explanation of Dynamic Specifications 9.6.1 Power Supply Rejection Ratio (PSRR) Known also as Ripple Rejection, this specification measures the ability of the regulator to reject noise and ripple beyond DC. PSRR is a summation of the individual rejections of the error amplifier, reference and AC leakage through the series pass transistor. The specification, in the form of a typical attenuation plot with respect to frequency, shows up the gain bandwidth compromises forced upon the designer in low quiescent current conditions. Generally: V OUT V IN PSSR = 20Log ---------------- dB using lower case to indicate AC values (EQ 15) Power supply rejection ratio is fixed by the internal design of the regulator. Additional rejection must be provided externally. www.austriamicrosystems.com/LDOs/AS1371 Revision 1.6 12 - 17 AS1371 Datasheet - A p p l i c a t i o n I n f o r m a t i o n 9.6.2 Output Capacitor ESR The series regulator is a negative feedback amplifier, and as such is conditionally stable. The ESR of the output capacitor is usually used to cancel one of the open loop poles of the error amplifier in order to produce a single pole response. Excessive ESR values may actually cause instability by excessive changes to the closed loop unity gain frequency crossover point. The range of ESR values for stability is usually shown either by a plot of stable ESR versus load current, or a limit statement in the datasheet. Some ceramic capacitors exhibit large capacitance and ESR variations in temperature. Z5U and Y5V capacitors may be required to ensure stability at temperatures below TAMB = -10C. With X7R or X5R capacitors, a 1F capacitor should be sufficient at all operating temperatures. Larger output capacitor values (10F) help to reduce noise and improve load transient-response, stability and power-supply rejection. 9.6.3 Input Capacitor An input capacitor at VIN is required for stability. It is recommended that a 1.0F capacitor be connected between the AS1371 power supply input pin VIN and ground (capacitance value may be increased without limit subject to ESR limits). This capacitor must be located at a distance of not more than 1cm from the VIN pin and returned to a clean analog ground. Any good quality ceramic, tantalum, or film capacitor may be used at the input. 9.6.4 Noise The regulator output is a DC voltage with noise superimposed on the output. The noise comes from three sources; the reference, the error amplifier input stage, and the output voltage setting resistors. Noise is a random fluctuation and if not minimized in some applications, will produce system problems. 9.6.5 Transient Response The series regulator is a negative feedback system, and therefore any change at the output will take a finite time to be corrected by the error loop. This "propagation time" is related to the bandwidth of the error loop. The initial response to an output transient comes from the output capacitance, and during this time, ESR is the dominant mechanism causing voltage transients at the output. More generally: V TRANSIENT = I OUTPUT R ESR Units are Volts, Amps, Ohms. (EQ 16) Thus an initial +50mA change of output current will produce a -12mV transient when the ESR=240m. Remember to keep the ESR within stability recommendations when reducing ESR by adding multiple parallel output capacitors. After the initial ESR transient, there follows a voltage droop during the time that the LDO feedback loop takes to respond to the output change. This drift is approx. linear in time and sums with the ESR contribution to make a total transient variation at the output of: T V TRANSIENT = I OUTPUT R ESR + ---------------- C LOAD Units are Volts, Seconds, Farads, Ohms. (EQ 17) Where: CLOAD is output capacitor T = Propagation delay of the LDO This shows why it is convenient to increase the output capacitor value for a better support for fast load changes. Of course the formula holds for t < "propagation time", so that a faster LDO needs a smaller cap at the load to achieve a similar transient response. For instance 50mA load current step produces 50mV output drop if the LDO response is 1usec and the load cap is 1F. There is also a steady state error caused by the finite output impedance of the regulator. This is derived from the load regulation specification discussed above. 9.6.6 Turn On Time This specification defines the time taken for the LDO to awake from shutdown. The time is measured from the release of the enable pin to the time that the output voltage is within 5% of the final value. It assumes that the voltage at VIN is stable and within the regulator min and max limits. Shutdown reduces the quiescent current to very low, mostly leakage values (<1A). 9.6.7 Thermal Protection To prevent operation under extreme fault conditions, such as a permanent short circuit at the output, thermal protection is built into the device. Die temperature is measured, and when a 150C threshold is reached, the device enters shutdown. When the die cools sufficiently, the device will restart (assuming input voltage exists and the device is enabled). Hysteresis of 20C prevents low frequency oscillation between start-up and shutdown around the temperature threshold. www.austriamicrosystems.com/LDOs/AS1371 Revision 1.6 13 - 17 AS1371 Datasheet - P a c k a g e D r a w i n g s a n d M a r k i n g s 10 Package Drawings and Markings The device is available in a 6-pin 2x2 TDFN package. Figure 18. Drawings and Dimensions Symbol A A1 A3 L b D E e D2 E2 aaa bbb ccc ddd eee fff N XXX AO Min 0.51 0 0.15 0.18 1.30 0.85 - Nom 0.55 0.02 0.15 REF 0.25 0.25 2.00 BSC 2.00 BSC 0.50 BSC 1.45 1.00 0.15 0.10 0.10 0.05 0.08 0.10 6 Max 0.60 0.05 0.35 0.30 1.10 - Notes: 1. 2. 3. 4. 5. Dimensions and tolerancing conform to ASME Y14.5M-1994. All dimensions are in millimeters. Angles are in degrees. Coplanarity applies to the exposed heat slug as well as the terminal. Radius on terminal is optional. N is the total number of terminals. www.austriamicrosystems.com/LDOs/AS1371 Revision 1.6 14 - 17 AS1371 Datasheet Revision History Revision Date 1.5 1.6 02 Jan, 2012 Owner Description afe Changes made across the document Note: Typos may not be explicitly mentioned under revision history. www.austriamicrosystems.com/LDOs/AS1371 Revision 1.6 15 - 17 AS1371 Datasheet - O r d e r i n g I n f o r m a t i o n 11 Ordering Information The device is available as the standard products listed in Table 4. Table 4. Ordering Information Ordering Code Marking Output Description Delivery Form Package Tape and Reel 6-pin 2x2 TDFN AS1371-BTDT-105 AO 1.05V 400mA, Low Input Voltage, Low Quiescent Current LDO 1 AM 1.2V 400mA, Low Input Voltage, Low Quiescent Current LDO Tape and Reel 6-pin 2x2 TDFN 1 AN 1.5V 400mA, Low Input Voltage, Low Quiescent Current LDO Tape and Reel 6-pin 2x2 TDFN 1 AT 1.8V 400mA, Low Input Voltage, Low Quiescent Current LDO Tape and Reel 6-pin 2x2 TDFN 1 AP 2.0V 400mA, Low Input Voltage, Low Quiescent Current LDO Tape and Reel 6-pin 2x2 TDFN 1 AQ 2.5V 400mA, Low Input Voltage, Low Quiescent Current LDO Tape and Reel 6-pin 2x2 TDFN 1 AR 3.0V 400mA, Low Input Voltage, Low Quiescent Current LDO Tape and Reel 6-pin 2x2 TDFN 1 AS VOUT 400mA, Low Input Voltage, Low Quiescent Current LDO Tape and Reel 6-pin 2x2 TDFN AS1371-BTDT-12 AS1371-BTDT-15 AS1371-BTDT-18 AS1371-BTDT-20 AS1371-BTDT-25 AS1371-BTDT-30 AS1371-SAMPLE 2 1. Available on request. 2. Non-standard devices from 0.6V to 3.3V are available in 50mV steps. Note: All products are RoHS compliant. Buy our products or get free samples online at ICdirect: http://www.austriamicrosystems.com/ICdirect Technical Support is available at http://www.austriamicrosystems.com/Technical-Support For further information and requests, please contact us mailto: sales@austriamicrosystems.com or find your local distributor at http://www.austriamicrosystems.com/distributor www.austriamicrosystems.com/LDOs/AS1371 Revision 1.6 16 - 17 AS1371 Datasheet - O r d e r i n g I n f o r m a t i o n Copyrights Copyright (c) 1997-2012, austriamicrosystems AG, Tobelbaderstrasse 30, 8141 Unterpremstaetten, Austria-Europe. Trademarks Registered (R). All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. All products and companies mentioned are trademarks or registered trademarks of their respective companies. Disclaimer Devices sold by austriamicrosystems AG are covered by the warranty and patent indemnification provisions appearing in its Term of Sale. austriamicrosystems AG makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. austriamicrosystems AG reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with austriamicrosystems AG for current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are specifically not recommended without additional processing by austriamicrosystems AG for each application. For shipments of less than 100 parts the manufacturing flow might show deviations from the standard production flow, such as test flow or test location. The information furnished here by austriamicrosystems AG is believed to be correct and accurate. However, austriamicrosystems AG shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of austriamicrosystems AG rendering of technical or other services. Contact Information Headquarters austriamicrosystems AG Tobelbaderstrasse 30 A-8141 Unterpremstaetten, Austria Tel: +43 (0) 3136 500 0 Fax: +43 (0) 3136 525 01 For Sales Offices, Distributors and Representatives, please visit: http://www.austriamicrosystems.com/contact www.austriamicrosystems.com/LDOs/AS1371 Revision 1.6 17 - 17 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: ams: AS1371-BTDT-105