HDSP-A4xC Series Alphanumeric Display, 0.54" (13.7 mm) 4 Character As Al In Ga P Red Data Sheet Description Features These 0.54" (13.7 mm) AS Al In Ga P displays are available in either common anode or common cathode. * As Al In Ga P red color * Gray face paint Gray package gives optimum contrast Devices * Design flexibility Common anode or common cathode As Al In Ga P Red Description HDSP-A42C Common Anode HDSP-A47C Common Cathode Applications * Suitable for alphanumeric * Operating temperature range -40C to 105C Package Dimensions 1.60 (0.063) 8.17 (0.322) 1.20 (0.047) 5 0.30 (0.012) 13.80 (0.543) 21.15 (0.833) 15.24 (0.600) PIN 1 12.70 (0.500) 12.70 (0.500) 12.70 (0.500) 1.84 (0.072) 50.96 (2.006) 6.00 (0.236) 7.00 (0.276) 3.70 (0.140) 1.94 (0.076) 5.59 (0.220) 0.50 (0.020) 38.52 (1.516) NOTES: 1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES). 2. UNLESS OTHERWISE STATED, TOLERANCES ARE 0.25 mm. Part Numbering System 5082 -X X X X-X X X X X HDSP-X X X X-X X X X X Mechanical Options[1] 00: No Mechanical Option Color Bin Options[1,2] 0: No Color Bin Limitation Maximum Intensity Bin[1,2] 0: No Maximum Intensity Bin Limitation Minimum Intensity Bin[1,2] 0: No Minimum Intensity Bin Limitation Device Configuration/Color[1] C: Al In Ga P Red Device Specific Configuration[1] Refer to Respective Datasheet Package[1] Refer to Respective Datasheet Notes: 1. For codes not listed in the figure above, please refer to the respective datasheet or contact your nearest Avago representative for details. 2. Bin options refer to shippable bins for a part number. Color and Intensity Bins are typically restricted to 1 bin per tube (exceptions may apply). Please refer to respective datasheet for specific bin limit information. 2 Internal Circuit DIG 1 DIG 2 DIG 3 DIG 4 DP1 DP2 COM 2 DIG 2 30 A 28 B A 9 C 7 D B 1 E C 36 F D E 33 G F 32 H G 6 5 J H K 4 L J 2 M K L 31 8 COM 1 DIG 1 34 29 COM 3 DIG 3 11 16 P N M 35 COM 4 DIG 4 DP1 P N 25 20 DP2 A A 19 B B 18 C C D COM 3 DIG 3 20 25 19 18 12 10 27 D F E E 22 20 G F G 12 10 27 H H 13 17 15 14 24 23 J K L N P J K L M M P N COMMON ANODE COM 2 COM 2 DIG 2 DIG 2 30 A 28 B A 9 C B 7 D C 1 E D 36 F E 33 G F 32 5 J H G 4 H K J 6 L K 2 M L 31 8 COM 1 DIG 1 34 29 P N M 35 N 11 COM 4 DIG 4 16 DP1 P A A DP2 B B C C D D E E F F 22 20 G G COMMON CATHODE Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 3 Pin Configuration A Common Anode 1E/2E Cathode 1M/2M Cathode No Connection 1L/2L Cathode 1K/2K Cathode 1J/2J Cathode 1D/2D Cathode DP2 Cathode 1C/2C Cathode 3E/4E Cathode DIGIT No. 3 Common Anode 3D/4D Cathode 3J/4J Cathode 3M/4M Cathode 3L/4L Cathode DIGIT No. 4 Common Anode 3K/4K Cathode 3C/4C Cathode 3B/4B Cathode 3H/4H Cathode No Connection 3G/4G Cathode 3P/4P Cathode 3N/4N Cathode 3A/4A Cathode DP1 Cathode 3F/4F Cathode 1B/2B Cathode DIGIT No. 2 Common Anode 1A/2A Cathode 1N/2N Cathode 1H/2H Cathode 1G/2G Cathode DIGIT No. 2 Common Anode 1P/2P Cathode 1F/2F Cathode Pin Configuration B Common Cathode 1E/2E Anode 1M/2M Anode No Connection 1L/2L Anode 1K/2K Anode 1J/2J Anode 1D/2D Anode DP2 Anode 1C/2C Anode 3E/4E Anode DIGIT No. 3 Common Cathode 3D/4D Anode 3J/4J Anode 3M/4M Anode 3L/4L Anode DIGIT No. 4 Common Cathode 3K/4K Anode 3C/4C Anode 3B/4B Anode 3H/4H Anode No Connection 3G/4G Anode 3P/4P Anode 3N/4N Anode 3A/4A Anode DP1 Anode 3F/4F Anode 1B/2B Anode DIGIT No. 2 Common Cathode 1A/2A Anode 1N/2N Anode 1H/2H Anode 1G/2G Anode DIGIT No. 2 Common Cathode 1P/2P Anode 1F/2F Anode H H J 13 17 15 14 24 23 J L N P K K L M M N P Absolute Maximum Ratings at TA = 25C Description DC Forward Current per Segment or DP[1,2,3] Peak Forward Current per Segment or DP[2,3] Average Forward Current[3] Symbol IF PEAK AVE HDSP-A42C/HDSP-A47C 50 100 30 Units mA mA mA Reverse Voltage per Segment or DP (IR = 100 A) Operating Temperature Storage Temperature Lead Soldering Conditions VR TO TS Temperature Time 5 -40 to +105 -40 to +120 260 3 V C C C s Notes: 1. Derate linearly as shown in Figure 1. 2. For long term performance with minimal light output degradation, drive currents between 10 mA and 30 mA are recommended. For more information on recommended drive conditions, please refer to Application Brief I-024 (5966-3087E). 3. Operating at currents below 1 mA is not recommended. Please contact your local representative for further information. Optical/Electrical Characteristics at TA = 25C Device Series HDSPA42C A47C Parameter Forward Voltage Reverse Voltage Peak Wavelength Symbol IV VR PEAK Min. 1.70 5 Typ. 1.90 20 635 Max. 2.20 Units V V nm Dominant Wavelength[3] Spectral Halfwidth d 1/2 622.5 626 17 630 nm nm Speed of Response s 20 ns Capacitance C 40 pF Intensity Bin Limits[1] (mcd at 10 mA) Bin Name Min.[2] T 18.0 U 25.0 Max.[2] 25.0 36.0 Notes: 1. Bin categories are established for classification of products. Products may not be available in all bin categories. 2. Tolerance for each bin limit is 10%. 4 Test Conditions IF = 20 mA IF = 100 A Peak Wavelength of Spectral Distribution at IF = 20 mA Wavelength Width at Spectral Distribution 1/2 Power Point at IF = 20 mA Exponential Time Constant, e-ts VF = 0, f = 1 MHz 40 30 20 10 0 20 0 40 60 80 100 120 TA - AMBIENT TEMPERATURE - C RELATIVE EFFICIENCY (NORMALIZED TO 1 AT 10 mA) Figure 1. Maximum forward current vs. ambient temperature. Derating based on TJMAX = 130C. 3.5 120 RELATIVE LUMINOUS INTENSITY (NORMALIZED TO 1 AT 10 mA) 50 IF - FORWARD CURRENT PER SEGMENT - mA IF - MAXIMUM AVERAGE CURRENT - mA 60 100 80 60 40 20 0 0.0 1.0 1.5 2.0 2.5 VF - FORWARD VOLTAGE - V Figure 2. Forward current vs. forwrad voltage. 3.0 3.0 2.5 2.0 1.5 1.0 0.5 0 0 10 20 30 40 50 60 IF - FORWARD CURRENT PER SEGMENT - mA Figure 3. Relative luminous intensity vs. DC forward current. 1.4 Contrast Enhancement 1.2 For information on contrast enhancement, please see Application Note 1015. 1.0 0.8 0.6 Soldering/Cleaning 0.4 Cleaning agents from ketone family (acetone, methyl ethyl ketone, etc.) and from the chlorinated hydrocarbon family (methylene chloride, trichloroethylene, carbon tetrachloride, etc.) are not recommended for cleaning LED parts. All of these various solvents attack or dissolve the encapsulating epoxies used to form the package of plastic LED parts. 0.2 0 0 10 20 30 40 50 60 IPEAK - PEAK FORWARD CURRENT PER SEGMENT - mA Figure 4. Relative efficiency (luminous intensity per unit current) vs. peak current. For information on soldering LEDs, please refer to Application Note 1027. 5 For product information and a complete list of distributors, please go to our website: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Pte. in the United States and other countries. Data subject to change. Copyright (c) 2006 Avago Technologies Pte. All rights reserved. Obsoletes 5988-4822EN 5988-9665EN May 9, 2006