L6924D Battery charger system with integrated power switch for Li-Ion/Li-Polymer Features Fully integrated solution, with a power MOSFET, reverse blocking diode, sense resistor, and thermal protection Ideal for coke and graphite anode single-cell LIION packs Both linear and quasi-pulse operation Closed loop thermal control USB BUS-compatible Programmable charge current up to 1 A Programmable pre-charge current Programmable end-of-charge current Programmable pre-charge voltage threshold Programmable charge timer Programmable output voltage at 4.1 V and 4.2 V, with 1 % output voltage accuracy (NTC) or (PTC) thermistor interface for battery temperature monitoring and protection Flexible charge process termination Status outputs to drive LEDs or to interface with a host processor Small VFQFPN 16-leads package (3 x 3 mm) VFQFPN16 Applications PDAs Handheld devices Cellular phones Digital cameras Standalone chargers USB-powered chargers Table 1. Device summary Order code Package L6924D Packaging Tube VFQFPN16 L6924D013TR September 2010 Tape and reel Doc ID 11908 Rev 9 1/38 www.st.com 38 Contents L6924D Contents 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Pins description and connection diagrams . . . . . . . . . . . . . . . . . . . . . . 4 2.1 3 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3.1 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3.2 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4.1 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 5 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 6 Operation description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7 8 2/38 6.1 Linear mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 6.2 Quasi-pulse mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Applications information: charging process . . . . . . . . . . . . . . . . . . . . 16 7.1 Charging process flow chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 7.2 Pre-charge current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 7.3 Pre-charge voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 7.4 Fast charge current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 7.5 End-of-charge current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 7.6 Recharge flow chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 7.7 Recharge threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 7.8 Maximum charging time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 7.9 Termination modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Application information: monitoring and protection . . . . . . . . . . . . . . 23 8.1 NTC thermistor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 8.2 Battery absence detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 8.3 Status pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Doc ID 11908 Rev 9 L6924D Contents 8.4 9 10 Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Additional applications information . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 9.1 Selecting the input capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 9.2 Selecting the output capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 9.3 Layout guidelines and demonstration board description . . . . . . . . . . . . . 30 Application ideas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 10.1 USB battery charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 11 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 12 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Doc ID 11908 Rev 9 3/38 Description 1 L6924D Description The L6924D is a fully monolithic battery charger dedicated to single-cell Li-Ion/Polymer battery packs. It is the ideal solution for space-limited applications, like PDAs, handheld equipment, cellular phones, and digital cameras. It integrates all of the power elements (the power MOSFET, reverse blocking diode and the sense resistor) in a small VFQFPN16 (3 x 3 mm) package. When an external voltage regulated wall adapter is used, the L6924D works in Linear Mode, and charges the battery in a constant current/constant voltage (CC/CV) profile. Moreover, when a current-limited adapter is used, the device can operate in quasipulse mode, dramatically reducing the power dissipation. Regardless of the charging approach, a closed loop thermal control avoids device overheating. The device has an operating input voltage ranging from 2.5 V to 12 V. The L6924D allows the user to program many parameters, such as pre-charge current, fast-charge current, pre-charge voltage threshold, end-of-charge current threshold, and charge timer. The L6924D offers two open collector outputs for diagnostic purposes, which can be used to either drive two external LEDs or communicate with a host microcontroller. Finally, the L6924D also provides very flexible control of the charge process termination and Gas Gauge capability, as well as other functions, such as checking for battery presence, and monitoring and protecting the battery from unsafe thermal conditions. 4/38 Figure 1. Minimum application size Figure 2. Basis application schematic Doc ID 11908 Rev 9 L6924D 2 Pins description and connection diagrams Pins description and connection diagrams Figure 3. Pins connection (top view) IPRE IPRG VPRE IEND V VIN VREF INSNS VOUT ST2 VOSNS ST1 V TPRG GND SD 2.1 Pin description Table 2. Pin functions OPRG TH Pin I/O Name Pin description 1 I VIN 2 I VINSNS 3-4 O 5 I TPRG Maximum charging time program pin. It must be connected with a capacitor to GND to fix the maximum charging time, see Chapter 7.8: Maximum charging time on page 20 6 - GND Ground pin. 7 I SD Shutdown pin. When connected to GND enables the device; when floating disables the device. Temperature monitor pin. It must be connected to a resistor divider including an NTC or PTC resistor. The charge process is disabled if the battery temperature (sensed through the NTC or PTC) is out of the programmable temperature window see Chapter 8.1: NTC thermistor on page 23. Input pin of the power stage. Supply voltage pin of the signal circuitry. The operating input voltage ranges from 2.5 V to 12 V and the start-up threshold is 4 V. ST2-ST1 Open-collector status pins. 8 I TH 9 I VOPRG Output voltage selection pin. VOUT = 4.1 V if left floating. VOUT = 4.2 V if connected to GND. 10 I VOSNS Output voltage sense pin. It senses the battery voltage to control the voltage regulation loop. 11 O VOUT Output pin. (connected to the battery) Doc ID 11908 Rev 9 5/38 Pins description and connection diagrams Table 2. 12 13 O I/O L6924D Pin functions VREF External reference voltage pin.(reference voltage is 1.8 V2%) IEND Charge termination pin. A resistor connected from this pin to GND fixes the charge termination current threshold IENDTH: if I < IENDTH, the charger behaves according to the VPRE status (see Chapter 7.5: End-of-charge current on page 19). The voltage across the resistor is proportional to the current delivered to the battery (Gas Gauge function). 14 I VPRE Multifunction pin. A resistor connected to GND allows the user to adjust the pre-charge voltage threshold VPRETH. If the pin is floating, VPRETH = 2.8 V. If the voltage on VPRE pin is lower than 0.8 V, VPRETH = 2.8 V and the charge is not automatically terminated when I < IENDTH. If the voltage on VPRE goes lower than 0.5 V (edge sensitive), the maximum charging time is reset. 15 I IPRG Charge current program pin. A resistor connected from this pin to GND, fixes the fast charge current value (ICHG), with an accuracy of 7%. IPRE Pre-charge current program pin. If the pin is floating IPRETH is equal to 10% of ICHG. If IPRETH has to be programmed at a different value, the pin has to be connected to GND or VREF, through a resistor see Chapter 7.2: Pre-charge current on page 17. 16 6/38 I Doc ID 11908 Rev 9 L6924D 3 Maximum ratings Maximum ratings Stressing the device above the rating listed in the "absolute maximum ratings" table may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 3.1 Absolute maximum ratings Table 3. Absolute maximum ratings Symbol Parameter Value Unit VIN Input voltage -0.3 to 16 V VINSNS, SD Input voltage -0.3 to VIN V Output voltage -0.3 to 5 V Output voltage -0.3 to 6 V Output current 30 mA -0.3 to 4 V 1.5 kV 2 kV Value Unit 75 C/W VOUT, VOSNS ST1, ST2 VREF, TH, IEND, IPRG, VPRE, IPRE, VOPRG, TPRG, GND ST1 and TH pins Other pins 3.2 Maximum withstanding voltage range test condition: CDFAEC-Q100-002 (Normal "human body model" acceptance criteria performance) Thermal data Table 4. Thermal data Symbol Parameter RthJA Thermal resistance junction to ambient (1) TSTG Storage temperature range -55 to 150 C TJ Junction temperature range -40 to 125 C TBD W PTOT Power dissipation at T= 70 C 1. Device mounted on demonstration board Doc ID 11908 Rev 9 7/38 Electrical specifications L6924D 4 Electrical specifications 4.1 Electrical characteristics TJ = 25 C, VIN = 5 V, unless otherwise specified. Table 5. Symbol VIN(1) IIN(1) Electrical characteristics Parameter Operating input voltage Min Typ 2.5 Start up threshold Supply current ISINK Current flowing from VOUT VOUT(1) Battery regulated voltage ICHG Test condition Charge current Max Unit 12 V 4.1 V Charging mode (RPRG = 24k) 1.8 2.5 mA Shutdown mode (RPRG = 24k) 60 80 A Shutdown mode (RPRG = 24k) 500 nA Stand by mode (RPRG = 24k) (VIN = 2.5V < VBATTERY) 500 nA VOPRG at VIN 4.06 4.1 4.14 V VOPRG at GND 4.16 4.2 4.24 V RPRG = 24k 450 490 525 mA RPRG = 12k 905 975 1045 mA IPRECH Pre-Charge current [default value = 10% ICHG] IPRE floating RPRG = 24k 41 49 56 mA IPRECH Pre-Charge current RPRE = 62k to GND; RPRG = 24k 57 67 78 mA IPRECH Pre-Charge current RPRE = 39k to VREF; RPRG = 24k 29.5 35 40.1 mA VPRETH Pre-Charge voltage threshold [default] VPRE = VPRETHDefault = Floating 2.7 2.8 2.9 V VPRETH Pre-Charge voltage threshold RVPRE = 13k; RPRG = 12k 2.87 3.03 3.19 V VPRETH Pre-Charge voltage threshold [default]. Charge termination disabled 2.7 2.8 2.9 V IENDTH Termination current 12 16 20 mA TMAXCH(2) Maximum charging time TMAXCH (2) Maximum charging time accuracy REND = 3K3 CTPRG = 10nF R[IPRG] = 24k 3 CTPRG = 5.6nF RPRG = 24k 10% Shutdown threshold high SDTH 2 Shutdown threshold low 0.4 Output status sink current Status on 10 RDS(on) Power MOSFET resistance RDS(on)@ICHG = 500mA 280 Doc ID 11908 Rev 9 V V ST1,2 8/38 hours mA 380 m L6924D Table 5. Electrical specifications Electrical characteristics (continued) Symbol Parameter Test condition NTC pin hot threshold voltage Min Typ Max Unit 10.625 12.5 14.375 %VREF TH NTC pin cold threshold voltage 45 50 55 %VREF 1. TJ from -40C to 125C. 2. Guaranteed by design. Doc ID 11908 Rev 9 9/38 Block diagram 5 Block diagram Figure 4. 10/38 L6924D Block diagram Doc ID 11908 Rev 9 L6924D 6 Operation description Operation description The L6924D is a fully integrated battery charger that allows a very compact battery management system for space limited applications. It integrates in a small package, all the power elements: power MOSFET, reverse blocking diode and the sense resistor. It normally works as a linear charger when powered from an external voltage regulated adapter. However, thanks to its very low minimum input voltage (down to 2.5 V) the L6924D can also work as a Quasi-Pulse charger when powered from a current limited adapter. To work in this condition, is enough to set the device's charging current higher than the adapter's one (Chapter 7.4 on page 18). The advantage of the linear charging approach is that the device has a direct control of the charging current and so the designer needn't to rely on the upstream adapter. However, the advantage of the Quasi-Pulse approach is that the power dissipated inside the portable equipment is dramatically reduced. The L6924D charges the battery in three phases: Pre-Charge constant current: in this phase (active when the battery is deeply discharged) the battery is charged with a low current. Fast-Charge constant current: in this phase the device charges the battery with the maximum current. Constant Voltage: when the battery voltage reaches the selected output voltage, the device starts to reduce the current, until the charge termination is done. The full flexibility is provided by: Programmable pre-charging current and voltage thresholds (IPRETH and VPRETH) (Chapter 7.2 on page 17, Chapter 7.3 on page 17). Programmable fast-charging current (ICHG) (Chapter 7.4 on page 18). Programmable end of charge current threshold (IENDTH) (Chapter 7.5 on page 19). Programmable end of charge timer (TMAXCH) (Chapter 7.8 on page 20). If the full flexibility is not required and a smaller number of external components is preferred, default values of IPRETH and VPRETH are available leaving the respective pins floating. If a PTC or NTC resistor is used, the device can monitor the battery temperature in order to protect the battery from operating in unsafe thermal conditions. Beside the good thermal behavior guaranteed by low thermal resistance of the package, additional safety is provided by the built-in temperature control loop. The IC monitors continuously its junction temperature. When the temperature reaches approximately 120C, the thermal control loop starts working, and reduces the charging current, in order to keep the IC junction temperature at 120C. Two open collector outputs are available for diagnostic purpose (status pins ST1 and ST2). They can be also used to drive external LEDs or to interface with a microcontroller. The voltage across the resistor connected between IEND and GND gives information about the actual charging current (working as a Gas Gauge), and it can be easily fed into a C ADC. Doc ID 11908 Rev 9 11/38 Operation description L6924D When the VPRE pin is not used to program the Pre-Charge voltage threshold, it has two different functions: If the voltage across VPRE pin is lower than 0.8 V, when I < IENDTH, the end of charge is notified by the status pin, but the charging process is not disabled. The charge process ends when the maximum charging time expires. If the voltage at VPRE pin false under 0.5 V the timer is reset on the falling edge. Battery disconnection control is provided thanks to the differentiated sensing and forcing output pins. A small current is sunk and forced through VOUT. If VOSNS doesn't detect the battery, the IC goes into a standby mode. Figure 5 shows the real charging profile of a Li-Ion battery, with a fast charge current of 450 mA (RPRG = 26 k), Figure 5. Li-Ion charging profile C harging profile 0.50 0 4.50 0 0.45 0 4.00 0 0.40 0 3.50 0 0.35 0 Ichg 2.50 0 0.25 0 2.00 0 0.20 0 Vbatt (V) Ichg (A) 3.00 0 Vb att 0.30 0 1.50 0 0.15 0 1.00 0 0.10 0 0.50 0 0.05 0 0.00 0 0.00 0 0 2 00 400 60 0 8 00 10 00 1 200 Charging tim e (sec ) 6.1 Linear mode When operating in linear mode, the device works in a way similar to a linear regulator with a constant current limit protection. It charges the battery in three phases: Pre-charging current ("Pre-Charge" phase). Constant current ("Fast-Charge" phase). Constant voltage ("Voltage Regulation" phase). VADP is the output voltage of the upstream AC-DC adapter that is, in turn, the input voltage of the L6924D. If the battery voltage is lower than a set pre-charge voltage (VPRETH), the pre-charge phase takes place. The battery is pre-charged with a low current IPRE (Chapter 7.2 on page 17). When the battery voltage goes higher than VPRETH, the battery is charged with the fast charge current ICHG, set through an external resistor (Chapter 7.4 on page 18). Finally, when the battery voltage is close to the regulated output voltage VOPRGTH (4.1 V or 4.2 V), the voltage regulation phase takes place and the charging current is reduced. The 12/38 Doc ID 11908 Rev 9 L6924D Operation description charging process is usually terminated when the charging current reaches a set value or when a charging timer expires (Chapter 7.9 on page 22). Figure 6 shows the different phases. Figure 6. Typical charge curves in linear mode Pre-Charge Phase V ADP V OPRGTH Fast-Charge Phase Voltage-Regulation Phase End Charge Adapter Voltage Battery Voltage V PRETH I CHG Charge Current I PRETH Power dissipation The worst case in power dissipation occurs when the device starts the fast-charge phase. In fact, the battery voltage is at its minimum value. In this case, this is the maximum difference between the adapter voltage and battery voltage, and the charge current is at its maximum value. The power dissipated is given by the following equation: Equation 1 PDIS = (VADP - VBAT ) x I CHG The higher the adapter voltage is, the higher the power dissipated. The maximum power dissipated depends on the thermal impedance of the device mounted on board. Doc ID 11908 Rev 9 13/38 Operation description 6.2 L6924D Quasi-pulse mode The quasi-pulse mode can be used when the system can rely on the current limit of the upstream adapter to charge the battery. In this case, ICHG must be set higher than the current limit of the adapter. In this mode, the L6924D charges the battery with the same three phases as in linear mode, but the power dissipation is greatly reduced as shown in Figure 7. Figure 7. Typical charge curves in quasi pulse mode Pre-Charge Phase Fast-Charge Phase Voltage Regulation Phase End Charge Adapter Voltage V ADP V O PRGTH Battery Voltage Ilim x Rdson V PRETH I CHG I LIM Charge Current I PRETH Power dissipation The big difference is due to the fact that ICHG is higher than the current limit of the adapter. During the fast-charge phase, the output voltage of the adapter drops and goes down to the battery voltage plus the voltage drop across the power MOSFET of the charger, as shown in the following equation: Equation 2 VIN = VADP = VBAT + VMOS Where VMOS is given by: Equation 3 V 14/38 MOS = R DS ( ON ) x I LIM Doc ID 11908 Rev 9 L6924D Operation description Where, ILIM = current limit of the wall adapter, and RDS(on) = resistance of the power MOSFET. The difference between the set charge current and the adapter limit should be high enough to minimize the RDS(on) value (and the power dissipation). This makes the control loop completely unbalanced and the power element is fully turned on. Figure 8 shows the RDS(on) values for different output voltage and charging currents for an adapter current limit of 500 mA. Figure 8. RDS(on) curves vs charging current and output voltage Neglecting the voltage drop across the charger (VMOS) when the device operates in this condition, its input voltage is equal to the battery one, and so a very low operating input voltage (down to 2.5 V) is required. The power dissipated by the device during this phase is: Equation 4 PCH = RDS ( on ) x I LIM 2 When the battery voltage approaches the final value, the charger gets back the control of the current, reducing it. Due to this, the upstream adapter exits the current limit condition and its output goes up to the regulated voltage VADP. This is the worst case in power dissipation: Equation 5 PDIS = (VADP - VBAT ) x I LIM In conclusion, the advantage of the linear charging approach is that the designer has the direct control of the charge current, and consequently the application can be very simple. The drawback is the high power dissipation. The advantage of the Quasi-Pulse charging method is that the power dissipated is dramatically reduced. The drawback is that a dedicated upstream adapter is required. Doc ID 11908 Rev 9 15/38 Applications information: charging process 7 Applications information: charging process 7.1 Charging process flow chart Figure 9. 16/38 Charging process flow chart Doc ID 11908 Rev 9 L6924D L6924D 7.2 Applications information: charging process Pre-charge current The L6924D allows pre-charging the battery with a low current when the battery voltage is lower than a specified threshold (VPRETH). The Pre-charge current has a default value equal to 10% of the fast-charge current. However it can be adjusted by connecting a resistor from the IPRE pin to GND or VREF (see Figure 10). When the resistor is connected between IPRE pin and GND, the current is higher than the default value. The RPRE value is given by: Equation 6 RPRE = VBG I PRECH VBG - K PRE RPRG Figure 10. IPRE pin connection IPRE L6924D When RPRE is connected to VREF, the current is lower than the default value. VREF is the external reference equal to 1.8 V, VBG is the internal reference equal to 1.23 V and KPRE is a constant equal to 950. See Figure 11. The relationship is shown in the equation 7: Equation 7 RPRE = VREF - VBG VBG I PRECH - RPRG KPRE Figure 11. IPRE pin connection VREF IPRE L6924D 7.3 Pre-charge voltage If the VPRE pin is floating, a default value of VPRETH is set, equal to 2.8 V (VPRETHDefault). Otherwise, the device offers the possibility to program this value, with a resistor connected between the VPRE pin and GND (see Figure 12). In this case, the RVPRE is given by the equation 8: Doc ID 11908 Rev 9 17/38 Applications information: charging process L6924D Equation 8 VPRETH RVPRE = RPRG x V PRETHDefault Figure 12. VPRE pin connection VPRE L6924D RPRE Where RVPRE is the resistor between VPRE and GND, and RPRG is the resistor used to set the charge current (see Section 7.4: Fast charge current), and VPRETH is the selected threshold. A safety timer is also present. If the battery voltage doesn't rise over VPRETH, before this time is expired, a fault is given (see Section 7.8: Maximum charging time). If at the beginning of the charge process, the battery voltage is higher than the VPRETH, the Pre-Charge phase is skipped. 7.4 Fast charge current When the battery voltage reaches the Pre-charge voltage threshold (VPRETH), the L6924D starts the Fast-charge Phase. In this phase, the device charges the battery with a constant current, ICHG, programmable by an external resistor that sets the charge current with an accuracy of 7% Figure 13. The equation used to select the RPRG as follows: Equation 9 KPRG RPRG = VBG x I CHG Figure 13. IPRG pin connection Where KPRG is a constant, equal to 9500. During this phase, the battery voltage increases until it reaches the programmed output voltage. A safety timer is also present. If this time expires, a fault is given (Section 7.8: Maximum charging time). 18/38 Doc ID 11908 Rev 9 L6924D 7.5 Applications information: charging process End-of-charge current When the charge voltage approaches the selected value (4.1 V or 4.2 V), the voltage regulation phase takes place. The charge current starts to decrease until it goes lower than a programmable end value, IENDTH, depending on an external resistor connected between the IEND pin and GND (see Figure 14). The equation that describes this relation as follows: Equation 10 KEND REND = VMIN x I ENDTH Figure 14. IEND pin connection Where KEND is 1050; and VMIN is 50 mV. Typically, this current level is used to terminate the charge process. However, it is also possible to disable the charge termination process based on this current level (Chapter 7.9 on page 22). This pin is also used to monitor the charge current, because the current injected in REND is proportional to ICHG. The voltage across REND can be used by a microcontroller to check the charge status like a gas gauge. Doc ID 11908 Rev 9 19/38 Applications information: charging process 7.6 L6924D Recharge flow chart Figure 15. Recharge flow chart FROM CHARGING PROCESS FLOW CHART FAULT END of CHARGE IND FAULT YES VBAT > VRCH VBAT > VRCH NO YES NO Detect High Fault Detect Low VBAT < VABS VBAT > VPRETH YES YES FAST CHARGE NO NO RETURN TO CHARGING PROCESS FLOW CHART Detect High Detect Low Fault YES DETECT LOW = a ISINK is sunk for a TDET from the battery DETECT HIGH = a IINJ is injected for a TDET in the battery DETECT LOW FAULT = a ISINK is sunk for a TDET from the battery DETECT HIGH FAULT = a IINJ is injected for a TDET in the battery VABS = VOPRG - 50mV VRCH = VOPRG - 150mV TDET = 100ms (Typ.) ISINK = IINJ = 1mA (Typ.) YES VBAT > VRCH VBAT > VPRETH PRE CHARGE NO NO BATTERY ABSENT BATTERY ABSENT GO TO BATTERY ABSENT FLOW CHART 7.7 Recharge threshold When, from an end-of-charge condition, the battery voltage goes lower than the recharging threshold (VRCH), the device goes back in charging state. The value of the recharge threshold is VOPRG-150 mV. 7.8 Maximum charging time To avoid the charging of a dead battery for a long time, the L6924D has the possibility to set a maximum charging time starting from the beginning of the fast-charge phase. This timer can be set with a capacitor, connected between the TPRG pin and GND. The CTPRG is the external capacitor (in nF) and is given by the following equation: Equation 11 C TPRG Note: 20/38 T MAXCH V BG x R PRG KT = V REF x 10 9 The maximum recommended CTPRG value must be less than 50 nF. Doc ID 11908 Rev 9 L6924D Applications information: charging process Figure 16. TPRG pin connection TPRG L6924D CTPRG Where, VREF = 1.8V, KT = 279 x 105, VBG = 1.23V, and TMAXCH is the charging time given in seconds. If the battery does not reach the end-of-charge condition before the timer expires, a fault is issued. Also during the pre-charge phase there is a safety timer, given by: Equation 12 1 TMAXPRECH = x TMAXCH 8 If this timer expires and the battery voltage is still lower than VPRETH, a fault signal is generated, and the charge process is terminated. Doc ID 11908 Rev 9 21/38 Applications information: charging process 7.9 L6924D Termination modes Figure 17. Charge termination flow chart As shown in Figure 14, it is possible to set an end of charge current IENDTH connecting a resistor between the IEND pin and GND. When the charge current goes down to this value, after a de-glitch time, the status pins notify that the charge process is complete. This deglitch time is expressed as: Equation 13 TDEGLITCH = TMAXCH 220 However, the termination of the charger process depends on the status of the VPRE pin: 22/38 If the voltage at the VPRE pin is higher than 0.8 V, the charge process is actually terminated when the charge current reaches IENDTH. If the voltage at VPRE pin goes lower than 0.8 V, the charge process does not terminate, and the charge current can go lower than IENDTH. The status pins notify the end-ofcharge as a fault condition, but the device continues the charge. When the TMAXCH is elapsed, the charge process ends, and a fault condition is issued. If the voltage on VPRE pin is lower than 0.8 V during the Pre-charge Phase, the device sets the VPRETHDefault automatically. If the voltage at the VPRE pin goes lower than 0.5 V (edge sensitive), the timer is reset, both in pre-charge and in fast-charge phase. Doc ID 11908 Rev 9 L6924D 8 Application information: monitoring and protection Application information: monitoring and protection The L6924D uses a VFQFPN 3 mm x 3 mm 16-pin package with an exposed pad that allows the user to have a compact application and good thermal behavior at the same time. The L6924D has a low thermal resistance because of the exposed pad (approximately 75C/W, depending on the board characteristics). Moreover, a built-in thermal protection feature prevents the L6924D from having thermal issues typically present in a linear charger. Thermal control is implemented with a thermal loop that reduces the charge current automatically when the junction temperature reaches approximately 120 C. This avoids further temperature rise and keeps the junction temperature constant. This simplifies the thermal design of the application as well as protects the device against over-temperature damage. The Figure 18 shows how the thermal loop acts (with the dotted lines), when the junction temperature reaches 120C. Figure 18. Power dissipation both linear and quasi pulse mode with thermal loop 8.1 NTC thermistor The device allows designers to monitor the battery temperature by measuring the voltage across an NTC or PTC resistor. Li-Ion batteries have a narrow range of operating temperature, usually from 0C to 50 C. This window is programmable by an external divider which is comprised of an NTC thermistor connected to GND and a resistor connected to VREF. When the voltage on the TH pin exceeds the minimum or maximum voltage threshold (internal window comparator), the device stops the charge process, and indicates a fault condition through the status pin. Doc ID 11908 Rev 9 23/38 Application information: monitoring and protection L6924D When the voltage (and thus, the temperature), returns to the window range, the device restarts the charging process. Moreover, there is a hysteresis for both the upper and lower thresholds, as shown in Figure 20. Figure 19. Battery temperature control flow chart Note: TBAT = OK when the battery temperature between 0C and 50C Figure 20. Voltage window with hysteresis on TH VMINTH VMINTH_HYS 900mV 780mV Voltage Variation on TH pin Charge disable Charge enable VMAXTH_HYS 248mV VMAXTH 225mV Figure 21. Pin connection VREF TH L6924D NTC 24/38 Doc ID 11908 Rev 9 L6924D Application information: monitoring and protection When the TH pin voltage rises and exceeds the VMINTH = 50% of VREF (900 mV typ), the L6924D stops the charge, and indicates a fault by the status pins. The device re-starts to charge the battery, only when the voltage at the TH pin goes under VMINTH_HYS = 780 mV (typ). For what concerns the high temperature limit, when the TH pin voltage falls under the VMAXTH = 12.5% of VREF (225 mV Typ.), the L6924D stops the charge until the TH pin voltage rises to the VMAXTH_HYS = 248 mV (Typ.). When the battery is at the low temperature limit, the TH pin voltage is 900 mV. The correct resistance ratio to set the low temperature limit at 0C can be found with the following equation: Equation 14 VMINTH = VREF x RNTC 0C RUP + RNTC 0C Where RUP is the pull-up resistor, VREF is equal to 1.8 V, and RNTC0C is the value of the NTC at 0C. Since at the low temperature limit VMINTH = 900 mV: Equation 15 0.9 = 1.8 x RNTC 0C RUP + RNTC 0C It follows that: Equation 16 RNTC 0C = RUP Similarly, when the battery is at the high temperature limit, the TH pin voltage is 225 mV. The correct resistance ratio to set the high temperature limit at 50C can be found with the following equation: Equation 17 VMAXTH = VREF x RNTC 50C RUP + RNTC 50C Where RNTC50C is the value of the NTC at 50C. Considering VMAXTH = 225 mV it follows that: Equation 18 0.225 = 1.8 x RNTC 50C RUP + RNTC 50C Consequently: Equation 19 RNTC 50C = Doc ID 11908 Rev 9 RUP 7 25/38 Application information: monitoring and protection L6924D Based on Equation 16: and Equation 19: , it derives that: Equation 20 RNTC 0C =7 RNTC 50C The temperature hysteresis can be estimated by the equation: Equation 21 THYS = VTH - VTH _ HYS VTH x NTCT Where VTH is the pin voltage threshold on the rising edge, VTH_HYS is the pin voltage threshold on the falling edge, and NTCT (-%/C) is the negative temperature coefficient of the NTC at temperature (T) expressed in % resistance change per C. For NTCT values, see the characteristics of the NTC manufacturers (e.g. the 2322615 series by VISHAY). At the low temperature, the hysteresis is approximately: Equation 22 THYS 0C = 900mV - 780mV 900mV x NTC 0C Obviously at the high temperature hysteresis is: Equation 23 THYS 50 C = 225 mV - 248 mV 225 mV x NTC 50 C Considering typical values for NTC0C and NTC50C, the hysteresis is: Equation 24 THYS 0C = 900mV - 780mV 2.5o C 900mV x 0.051 THYS 50C = 225mV - 248mV -2.5o C 225mV x 0.039 And: Equation 25 If a PTC connected to GND is used, the selection is the same as above, the only difference is when the battery temperature increases, the voltage on the TH pin increases, and vice versa. For applications that do not need a monitor of the battery temperature, the NTC can be replaced with a simple resistor whose value is one half of the pull-up resistor RUP. In this case, the voltage at the TH pin is always inside the voltage window, and the charge is always enabled. 26/38 Doc ID 11908 Rev 9 L6924D 8.2 Application information: monitoring and protection Battery absence detection This feature provides a battery absent detection scheme to detect the removal or the insertion of the battery. If the battery is removed, the charge current falls below the IENDTH. At the end of the de-glitch time, a detection current IDETECT, equal to 1 mA, is sunk from the output for a time of TDETECT. The device checks the voltage at the output. If it is below the VPRETH, a current equal to IDETECT is injected in the output capacitor for a TDETECT, and it is checked to see if the voltage on the output goes higher than VABS (the value is VOPRGTH-50 mV). If the battery voltage changes from VPRETH to VABS and vice versa in a TDETECT time, it means that no battery is connected to the charger. The TDETECT is expressed by: Equation 26 TDETECT = TMAXCH 54x103 Figure 22. Battery absent detection flow chart DETECT LOW ABSENT = a ISINK is sunk for a TDET from the battery DETECT HIGH ABSENT = a IINJ is injected for a TDET in the battery TDET = 100ms (Typ.) ISINK = IINJ = 1mA (Typ.) BATTERY ABSENT Detect Low Absent YES VBAT > VPRETH FAST CHARGE NO Detect High Absent YES 8.3 VBAT > VRCH NO PRE CHARGE Status pins To indicate various charger status conditions, there are two open-collector output pins, ST1 and ST2. These status pins can be used either to drive status LEDs, connected to an external power source, by a resistor, or to communicate to a host processor. These pins must never be connected to the VIN when it exceeds their absolute value (6 V). Doc ID 11908 Rev 9 27/38 Application information: monitoring and protection L6924D Figure 23. ST1 and ST2 connection with LEDs or microcontroller Table 6. Status LEDs indications Charge condition ST1 ST2 Charge in progress When the device is in pre-charge or fast-charge status ON OFF Charge done When the charging current goes lower than the IENDTH OFF ON When the input voltage goes under VBAT-50 mV OFF OFF When the voltage on the TH pin is out of the programmable window, in accordance with the NTC or PTC thermistor ON ON When the battery pack is removed ON ON When TMAXCH or TMAXPRECH is expired ON ON Stand by mode Bad battery temperature Battery absent Over time 8.4 Description Shutdown The L6924D has a shutdown pin (SD) that allows enabling or disabling the device. If the SD pin voltage is below 0.4 V (e.g. pin connected to GND), the device is enabled, whereas if the SD pin voltage exceeds 2 V (e.g. the shutdown pin is left floating) the device is disabled. When the device enters the shutdown mode, the current consumption is reduced to 60 A typ. In this condition, VREF is turned off. The Figure 24 clarifies the SD pin behavior. 28/38 Doc ID 11908 Rev 9 L6924D Application information: monitoring and protection Figure 24. Shutdown SD pin voltage device disabled 2V SDTH,high 0.4V SDTH,low device enabled Doc ID 11908 Rev 9 29/38 Additional applications information L6924D 9 Additional applications information 9.1 Selecting the input capacitor In most applications, a 1 F ceramic capacitor, placed close to the VIN and VINSN pins can be used to filter the high frequency noise. 9.2 Selecting the output capacitor Typically, 1 F ceramic capacitor placed close to the VOUT and VOUTSN pin is enough to keep voltage control loop stable. This ensures proper operation of battery absent detection in removable battery pack applications. 9.3 Layout guidelines and demonstration board description The thermal loop keeps the device at a constant temperature of approximately 120C which in turn, reduces ICHG. However, in order to maximize the current capability, it is important to ensure a good thermal path. Therefore, the exposed pad must be properly soldered to the board and connected to the other layer through thermal vias. The recommended copper thickness of the layers is 70 m or more. The exposed pad must be electrically connected to GND. Figure 25 shows the thermal image of the board with the power dissipation of 1 W. In this instance, the temperature of the case is 89C, but the junction temperature of the device is given by the following equation: Equation 27 TJ = RTHJ - A x PDISS + TAMB Where the RTH J-A of the device mounted on board is 75 C/W, the power dissipated is 1 W, and the ambient temperature is 25 C. In this case the junction temperature is: Equation 28 TJ = 75 x1 + 25 = 100o C 30/38 Doc ID 11908 Rev 9 L6924D Additional applications information Figure 25. Thermal image of the demonstration board The VOSNS pin can be used as a remote sense; it should be therefore connected as closely as possible to the battery. The demonstration board layout and schematic are shown in Figure 26, Figure 27 and Figure 28. Figure 26. Demonstration board layout, top side Figure 27. Demonstration board layout, bottom side Doc ID 11908 Rev 9 31/38 Additional applications information L6924D Figure 28. Demonstration board schematic R9 R3 C4 CHARGER VIN VREF NTC TH VOUT VINSNS R1 BATTERY VOSNS C1 IEND R2 C2 LD1 TPRG IPRG L6924D C3 LD2 J2 R4 ST2 VPRE ST1 J1 R5 J5 SHDN GND VOPRG J3 J4 IPRE R6 C Vref R7 32/38 R8 Doc ID 11908 Rev 9 R10 L6924D Additional applications information Table 7. Demonstration board components description Name Value R1 1k Pull up resistor. To be used when the ST1 is connected to a LED. R2 1k Pull up resistor. To be used when the ST1 is connected to a LED. R3 1k Pull up resistor. Connected between VREF and TH pin. R4 3k3 End of charge current resistor. Used to set the termination current and, as a "Gas Gauge" when measuring the voltage across on it. R5 24k Fast-charge current resistor. Used to set the charging current. R6 N.M. VPRETH resistor. Used to set programmable pre-charge voltage threshold. If not mounted, the VPRETHDefault, equal to 2.8V, is set. R7 N.M. IPRETH resistor. Used to set the programmable pre-charge current threshold below the default one. If not mounted, the IPRETHDefault is set. R8 68k IPRETH resistor. Used to set the programmable pre-charge current threshold above the default one. If not mounted, the IPRETHDefault is set. R9 470R If a NTC is not used, a half value of R3 must be mounted to keep the TH voltage in the correct window. R10 N.M. It has the same function of R6. Moreover, if it is replaced with a short-circuit, when J5 is closed, the timer is reset (falling edge). C1 1F Input capacitor. C2 10nF TMAX capacitor. Used to set the maximum charging time. C3 4.7F Output capacitor. C4 1nF LD1 LD2 Description VREF filter capacitor. GREEN ST1 LED. RED ST2 LED. J1 ST1 jumper. Using to select the LED or the external C. J2 ST2 jumper. Using to select the LED or the external C. J3 SD jumper. If open, the device is in shutdown mode; when closed, the device starts to work. J4 VOPRG jumper. If closed, the 4.2V output voltage is set; if open, the 4.1V is set. J5 VPRE jumper. If closed with R10 in short-circuit with GND, resets the timer. Doc ID 11908 Rev 9 33/38 Application ideas L6924D 10 Application ideas 10.1 USB battery charger With a voltage range between 4.75 V and 5.25 V, and a maximum current up to 500 mA, the USB power bus is an ideal source for charging a single-cell Li-Ion battery. Since it is not possible to rely on the USB current limit to charge the battery, a linear approach must be adopted. Therefore, it is only necessary to set the ICHG with a maximum value lower than 500 mA, and the device will charge the battery in Linear mode. Figure 29 shows an example of USB charger application schematic. Figure 29. USB charger application R1 C4 VBUS GND VIN VOUT C1 SYSTEM AND PACK VOSNS VINSNS D- D+ BATTERY TH VREF IEND C3 TPRG C2 L6924D IPRG R2 VPRE ST1 ST2 SD GND V IPRE OPRG USB CONTROLLER R4 34/38 Doc ID 11908 Rev 9 R5 R3 L6924D 11 Package mechanical data Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark. Doc ID 11908 Rev 9 35/38 Package mechanical data Table 8. L6924D VFQFPN16 (3 x 3 mm.) mechanical data mm. Dim. Min. Typ. Max. 0.80 0.90 1.00 A1 0.02 0.05 A2 0.65 1.00 A3 0.20 A b 0.18 0.25 0.30 D 2.85 3.00 3.15 D2 1.45 1.60 1.75 E 2.85 3.00 3.15 E2 1.45 1.60 1.75 e 0.45 0.50 0.55 L 0.30 0.40 0.50 Figure 30. Package dimensions 7185330_G 36/38 Doc ID 11908 Rev 9 L6924D 12 Revision history Revision history Table 9. Document revision history Date Revision Changes 16-Dec-2005 1 First draft 20-Dec-2005 2 Package dimensions updated 10-Jan-2006 3 Few updates 14-Feb-2006 4 Part number updated 03-Jul-2006 5 Updates to equation in page 22, updated block diagram Figure 4. 07-Sep-2006 6 Added Note: on page 20, updated value CTPRG page 8 29-Jun-2007 7 Updated capacitor values C2, C3 in Table 7 on page 33 05-Jul-2010 8 Updated Table 5 on page 8 and Section 8.4 on page 28 22-Sep-2010 9 Updated Table 8 and Figure 30 on page 36. Minor changes. Doc ID 11908 Rev 9 37/38 L6924D Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2010 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 38/38 Doc ID 11908 Rev 9