SRDA05-4R2G - ON SEMICONDUCTOR

© Semiconductor Components Industries, LLC, 2007

June, 2007 - Rev. 5

1Publication Order Number:

SRDA05-4R2/D

SRDA05-4R2

Low Capacitance Surface

Mount TVS for High-Speed

Data Interfaces

The SRDA05-4 transient voltage suppressor is designed to protect

equipment attached to high speed communication lines from ESD,

EFT, and lightning.

Features

•SO-8 Package

•Peak Power - 500 Watts 8 x 20 mS

•ESD Rating:

IEC 61000-4-2 (ESD) 15 kV (air) 8 kV (contact)

IEC 61000-4-4 (EFT) 40 A (5/50 ns)

IEC 61000-4-5 (lightning) 23 (8/20 ms)

•UL Flammability Rating of 94 V-0

•Pb-Free Package is Available

Typical Applications

•High Speed Communication Line Protection

MAXIMUM RATINGS

Rating Symbol Value Unit

Peak Power Dissipation

8 x 20 mS @ TA = 25°C (Note 1)

Ppk 500 W

Junction and Storage Temperature Range TJ, Tstg -  55 to +150 °C

Lead Solder Temperature -

Maximum 10 Seconds Duration

TL260 °C

Stresses exceeding Maximum Ratings may damage the device. Maximum

Ratings are stress ratings only. Functional operation above the Recommended

Operating Conditions is not implied. Extended exposure to stresses above the

Recommended Operating Conditions may affect device reliability.

1. Non-repetitive current pulse 8 x 20 mS exponential decay waveform

SO-8 LOW CAPACITANCE

VOLTAGE SUPPRESSOR

500 WATTS PEAK POWER

6 VOLTS

MARKING DIAGRAM

SOIC-8

CASE 751

PLASTIC

PIN CONFIGURATION

AND SCHEMATIC

I/O 1 1

REF 1 2

REF 1 3

I/O 2 4

8 REF 2

7 I/O 4

6 I/O 3

5 REF 2

http://onsemi.com

†For information on tape and reel specifications,

including part orientation and tape sizes, please

refer to our Tape and Reel Packaging Specification

Brochure, BRD8011/D.

SRDA5

AYWWG

SRDA5 = Device Code

A = Assembly Location

Y = Year

WW = Work Week

G= Pb-Free Package

(Note: Microdot may be in either location)

Device Package

ORDERING INFORMATION

Shipping†

SRDA05-4R2 SO-8 2500/Tape & Reel

SRDA05-4R2G SO-8

(Pb-Free)

2500/Tape & Reel

SRDA05-4R2

http://onsemi.com

ELECTRICAL CHARACTERISTICS

Characteristic Symbol Min Typ Max Unit

Reverse Breakdown Voltage @ It = 1.0 mA VBR 6.0 - - V

Reverse Leakage Current @ VRWN = 5.0 V IRN/A - 10 mA

Maximum Clamping Voltage @ IPP = 1.0 A, 8 x 20 mSVCN/A - 9.8 V

Maximum Clamping Voltage @ IPP = 10 A, 8 x 20 mSVCN/A - 12 V

Between I/O Pins and Ground @ VR = 0 V, 1.0 MHz Capacitance - 10 15 pF

Between I/O Pins @ VR = 0 Volts, 1.0 MHz Capacitance - 5 8 pF

ELECTRICAL CHARACTERISTICS

(TA = 25°C unless otherwise noted)

UNIDIRECTIONAL (Circuit tied to Pins 1 and 3 or 2 and 3)

Symbol Parameter

IPP Maximum Reverse Peak Pulse Current

VCClamping Voltage @ IPP

VRWM Working Peak Reverse Voltage

IRMaximum Reverse Leakage Current @ VRWM

VBR Breakdown Voltage @ IT

ITTest Current

QVBR Maximum Temperature Coefficient of VBR

IFForward Current

VFForward Voltage @ IF

ZZT Maximum Zener Impedance @ IZT

IZK Reverse Current

ZZK Maximum Zener Impedance @ IZK

Uni-Directional TVS

IPP

VRWM

VCVBR

SRDA05-4R2

http://onsemi.com

TYPICAL CHARACTERISTICS

-100 0

Figure 1. Reverse Breakdown versus

Temperature

-50

T, TEMPERATURE (°C)

100 200

Figure 2. Reverse Leakage versus

Temperature

VZ, REVERSE BREAKDOWN (V)

-100 -50 50 100

T, TEMPERATURE (°C)

200

50 150

0 150

IR, REVERSE LEAKAGE (mA)

Figure 3. 8 x 20 ms Pulse Waveform

100

00204060

t, TIME (ms)

% OF PEAK PULSE CURRENT

PULSE WIDTH (tP) IS DEFINED

AS THAT POINT WHERE THE

PEAK CURRENT DECAY = 8 ms

PEAK VALUE IRSM @ 8 ms

HALF VALUE IRSM/2 @ 20 ms

Figure 4. Clamping Voltage versus Peak Pulse

Current

00204060

IPP

, PEAK PULSE CURRENT (A)

VC, CLAMPING VOLTAGE (V)

10 30 50 70 90

SRDA05-4R2

http://onsemi.com

APPLICATIONS INFORMATION

The SRDA05-4R2 is a low capacitance TVS diode array

designed to protect sensitive electronics such as

communications systems, computers, and computer

peripherals against damage due to ESD events or transient

overvoltage conditions. Because of its low capacitance, it

can be used in high speed I/O data lines. The integrated

design of the SRDA05-4R2 offers surge rated, low

capacitance steering diodes and a TVS diode integrated in a

single package (SO-8). If a transient condition occurs, the

steering diodes will drive the transient to the positive rail of

the power supply or to ground. The TVS device protects the

power line against overvoltage conditions avoiding damage

to the power supply and other downstream components.

SRDA05-4R2 Configuration Options

The SRDA05-4R2 is able to protect up to four data lines

against transient overvoltage conditions by driving them to

a fixed reference point for clamping purposes. The steering

diodes will be forward biased whenever the voltage on the

protected line exceeds the reference voltage (Vf or Vcc+Vf).

The diodes will force the transient current to bypass the

sensitive circuit.

Data lines are connected at pins 1, 4, 6 and 7. The negative

reference is connected at pins 5 and 8. These pins must be

connected directly to ground using a ground plane to

minimize the PCB's ground inductance. It is very important

to reduce the PCB trace lengths as much as possible to

minimize parasitic inductances.

Option 1

Protection of four data lines and the power supply using

Vcc as reference.

I/O 1

I/O 2

I/O 3

I/O 4

VCC

Figure 5.

For this configuration, connect pins 2 and 3 directly to the

positive supply rail (Vcc). The data lines are referenced to

the supply voltage. The internal TVS diode prevents

overvoltage on the supply rail. Biasing of the steering diodes

reduces their capacitance.

Option 2

Protection of four data lines with bias and power supply

isolation resistor.

I/O 1

I/O 2

I/O 3

I/O 4

VCC

10 K

Figure 6.

The SRDA05-4R2 can be isolated from the power supply

by connecting a series resistor between pins 2 and 3 and Vcc.

A 10 kW resistor is recommended for this application. This

will maintain a bias on the internal TVS and steering diodes,

reducing their capacitance.

Option 3

Protection of four data lines using the internal TVS diode

as reference.

I/O 1

I/O 2

I/O 3

I/O 4

Figure 7.

In applications lacking a positive supply reference or

those cases in which a fully isolated power supply is

required, the internal TVS can be used as the reference. For

these applications, pins 2 and 3 are not connected. In this

configuration, the steering diodes will conduct whenever the

voltage on the protected line exceeds the working voltage of

the TVS plus one diode drop (Vc=Vf + VTVS).

SRDA05-4R2

http://onsemi.com

ESD Protection of Power Supply Lines

When using diodes for data line protection, referencing to

a supply rail provides advantages. Biasing the diodes reduces

their capacitance and minimizes signal distortion.

Implementing this topology with discrete devices does have

disadvantages. This configuration is shown below:

VCC

Data Line

IESDpos

IESDneg

VF + VCC

-VF

IESDpos

IESDneg

Power

Supply

Protected

Device

Figure 8.

Looking at the figure above, it can be seen that when a

positive ESD condition occurs, diode D1 will be forward

biased while diode D2 will be forward biased when a negative

ESD condition occurs. For slower transient conditions, this

system may be approximated as follows:

For positive pulse conditions:

Vc = Vcc + VfD1

For negative pulse conditions:

Vc = -VfD2

ESD events can have rise times on the order of some

number of nanoseconds. Under these conditions, the effect of

parasitic inductance must be considered. A pictorial

representation of this is shown below.

VCC

Data Line

IESDpos

IESDneg

VC = VCC + Vf + (L diESD/dt)

IESDpos

IESDneg

Power

Supply

Protected

Device

VC = -Vf - (L diESD/dt)

Figure 9.

An approximation of the clamping voltage for these fast

transients would be:

For positive pulse conditions:

Vc = Vcc + Vf + (L diESD/dt)

For negative pulse conditions:

Vc = -Vf – (L diESD/dt)

As shown in the formulas, the clamping voltage (Vc) not

only depends on the Vf of the steering diodes but also on the

L diESD/dt factor. A relatively small trace inductance can result

in hundreds of volts appearing on the supply rail. This

endangers both the power supply and anything attached to

that rail. This highlights the importance of good board layout.

Taking care to minimize the effects of parasitic inductance

will provide significant benefits in transient immunity.

Even with good board layout, some disadvantages are still

present when discrete diodes are used to suppress ESD events

across datalines and the supply rail. Discrete diodes with good

transient power capability will have larger die and therefore

higher capacitance. This capacitance becomes problematic as

transmission frequencies increase. Reducing capacitance

generally requires reducing die size. These small die will have

higher forward voltage characteristics at typical ESD

transient current levels. This voltage combined with the

smaller die can result in device failure.

The ON Semiconductor SRDA05- 4R2 was developed to

overcome the disadvantages encountered when using discrete

diodes for ESD protection. This device integrates a TVS

diode within a network of steering diodes.

Figure 10. SRDA05-4R2 Equivalent Circuit

During an ESD condition, the ESD current will be driven

to ground through the TVS diode as shown below.

VCC

Data Line

IESDpos

Power

Supply

Protected

Device

Figure 11.

The resulting clamping voltage on the protected IC will

be:

Vc = VFD1 + VTVS.

The clamping voltage of the TVS diode is provided in

Figure 4 and depends on the magnitude of the ESD current.

The steering diodes are fast switching devices with unique

forward voltage and low capacitance characteristics.

SRDA05-4R2

http://onsemi.com

TYPICAL APPLICATIONS

UPSTREAM

USB PORT

VBUS

VBUS VBUS

VBUS

DOWNSTREAM

USB PORT

DOWNSTREAM

USB PORT

D-

D+

D-

D+

GND

D-

D+

GND

USB

Controller

NUP2201MR6

SRDA05-4R2

Figure 12. ESD Protection for USB Port

Figure 13. Protection for Ethernet 10/100 (Differential Mode)

PHY

Ethernet

(10/100)

Coupling

Transformers

SRDA05-4R2

RJ45

Connector

N/C N/C

TX+

TX-

RX+

RX-

TX+

TX-

RX+

RX-

GND

VCC

SRDA05-4R2

http://onsemi.com

T1/E1

TRANCEIVER

RTIP

RRING

TRING

TTIP

R2 R3

SRDA05-4R2

VCC

Figure 14. TI/E1 Interface Protection

SRDA05-4R2

http://onsemi.com

PACKAGE DIMENSIONS

SOIC-8 NB

CASE 751-07

ISSUE AH

SEATING

PLANE

X 45 _

NOTES:

1. DIMENSIONING AND TOLERANCING PER

ANSI Y14.5M, 1982.

2. CONTROLLING DIMENSION: MILLIMETER.

3. DIMENSION A AND B DO NOT INCLUDE

MOLD PROTRUSION.

4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)

PER SIDE.

5. DIMENSION D DOES NOT INCLUDE DAMBAR

PROTRUSION. ALLOWABLE DAMBAR

PROTRUSION SHALL BE 0.127 (0.005) TOTAL

IN EXCESS OF THE D DIMENSION AT

MAXIMUM MATERIAL CONDITION.

6. 751-01 THRU 751-06 ARE OBSOLETE. NEW

STANDARD IS 751-07.

0.10 (0.004)

DIM

MIN MAX MIN MAX

INCHES

4.80 5.00 0.189 0.197

MILLIMETERS

B3.80 4.00 0.150 0.157

C1.35 1.75 0.053 0.069

D0.33 0.51 0.013 0.020

G1.27 BSC 0.050 BSC

H0.10 0.25 0.004 0.010

J0.19 0.25 0.007 0.010

K0.40 1.27 0.016 0.050

M0 8 0 8

N0.25 0.50 0.010 0.020

S5.80 6.20 0.228 0.244

-X-

-Y-

0.25 (0.010)

-Z-

0.25 (0.010) ZSXS

____

1.52

0.060

7.0

0.275

0.6

0.024

1.270

0.050

4.0

0.155

ǒmm

inchesǓ

SCALE 6:1

*For additional information on our Pb-Free strategy and soldering

details, please download the ON Semiconductor Soldering and

Mounting Techniques Reference Manual, SOLDERRM/D.

SOLDERING FOOTPRINT*

ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice

to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability

arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.

“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All

operating parameters, including “Typicals” must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights

nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications

intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should

Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,

and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death

associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal

Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.

PUBLICATION ORDERING INFORMATION

N. American Technical Support: 800-282-9855 Toll Free

USA/Canada

Europe, Middle East and Africa Technical Support:

Phone: 421 33 790 2910

Japan Customer Focus Center

Phone: 81-3-5773-3850

SRDA05-4R2/D

LITERATURE FULFILLMENT:

Literature Distribution Center for ON Semiconductor

P.O. Box 5163, Denver, Colorado 80217 USA

Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada

Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada

Email: orderlit@onsemi.com

ON Semiconductor Website: www.onsemi.com

Order Literature: http://www.onsemi.com/orderlit

For additional information, please contact your local

Sales Representative