LTC2446/LTC2447 24-Bit High Speed 8-Channel ADCs with Selectable Multiple Reference Inputs DESCRIPTION FEATURES Five Selectable Differential Reference Inputs nn Four Differential/Eight Single-Ended Inputs nn 4-Way MUX for Multiple Ratiometric Measurements nn Up to 8kHz Output Rate (External f ) O nn Up to 4kHz Multiplexing Rate (External f ) O nn Selectable Speed/Resolution: 2VRMS Noise at 1.76kHz Output Rate 200nVRMS Noise at 13.8Hz Output Rate with Simultaneous 50/60Hz Rejection nn Guaranteed Modulator Stability and Lock-Up Immunity for any Input and Reference Conditions nn 0.0005% INL, No Missing Codes nn Autosleep Enables 20A Operation at 6.9Hz nn <5V Offset (4.5V < V CC < 5.5V, -40C to 85C) nn Differential Input and Differential Reference with GND to VCC Common Mode Range nn No Latency Mode, Each Conversion is Accurate Even After a New Channel is Selected nn Internal Oscillator--No External Components nn LTC2447 Includes MUXOUT/ADCIN for External Buffering or Gain nn Tiny QFN 5mm x 7mm Package The LTC(R)2446/LTC2447 4-terminal switching enables multiplexed ratiometric measurements. Four sets of selectable differential inputs coupled with four sets of differential reference inputs allow multiple RTDs, bridges and other sensors to be digitized by a single converter. A fifth differential reference input can be selected for any input channel not requiring ratiometric measurements (thermocouples, voltages, current sense, etc.). The flexible input multiplexer allows single-ended or differential inputs coupled with a slaved reference input or a universal reference input. APPLICATIONS L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. patents, including 6140950, 6169506, 6208279, 6411242, 6639526. nn Flow Weight Scales nn Pressure nn Direct Temperature Measurement nn Gas Chromatography A proprietary delta-sigma architecture results in absolute accuracy (offset, full-scale, linearity) of 15ppm, noise as low as 200nVRMS and speeds as high as 8kHz. Through a simple 4-wire interface, ten speed/resolution combinations can be selected. The first conversion following a speed, resolution, channel change or reference change is valid since there is no settling time between conversions, enabling scan rates of up to 4kHz. Additionally, a 2x mode can be selected for any speed-enabling output rates up to 8kHz with one cycle of latency. nn nn TYPICAL APPLICATION LTC2446 RMS Noise vs Speed Multiple Ratiometric Measurement System IN+ * * * 19-INPUT 4-OUTPUT MUX IN- + - VCC = 5V VREF = 5V VIN+ = VIN- = 0V 2x SPEED MODE NO LATENCY MODE LTC2446 REF+ CS VARIABLE SPEED/ RESOLUTION 24-BIT ADC SDI 10 RMS NOISE (V) VCC 100 2.8V AT 880Hz 1 280nV AT 6.9Hz (50/60Hz REJECTION) SDO SCK REF- 0.1 24467 TA01 1 1000 10 100 CONVERSION RATE (Hz) 10000 24467 TA02 24467fb For more information www.linear.com/LTC2446 1 LTC2446/LTC2447 ABSOLUTE MAXIMUM RATINGS Supply Voltage (VCC) to GND........................ -0.3V to 6V Analog Input Pins Voltage to GND.......................................-0.3V to (VCC + 0.3V) Reference Input Pins Voltage to GND.......................................-0.3V to (VCC + 0.3V) Digital Input Voltage to GND..........-0.3V to (VCC + 0.3V) Digital Output Voltage to GND........-0.3V to (VCC + 0.3V) Operating Temperature Range LTC2446C/LTC2447C ............................... 0C to 70C LTC2446I/LTC2447I .............................-40C to 85C Storage Temperature Range................... -65C to 125C PIN CONFIGURATION LTC2447 GND GND SDI 38 37 36 35 34 33 32 GND 1 31 GND BUSY 2 CS SCK 38 37 36 35 34 33 32 GND 1 FO TOP VIEW GND GND SDI FO CS SDO SCK TOP VIEW SDO LTC2446 31 GND - BUSY 2 30 REFG- REFG+ EXT 3 29 REFG+ 30 REFG EXT 3 29 GND 4 28 VCC GND 4 28 VCC GND 5 27 NC GND 5 27 MUXOUTN GND 6 26 NC GND 6 25 NC COM 7 CH0 8 24 NC CH0 8 24 MUXOUTP CH1 9 23 VREF67+ CH1 9 23 VREF67+ - 22 VREF67- + 21 CH7 - 22 VREF67 VREF01 11 21 CH7 VREF01 11 CH2 12 20 CH6 CH2 12 20 CH6 VREF45+ VREF45- CH3 UHF PACKAGE 38-LEAD (5mm x 7mm) PLASTIC QFN TJMAX = 125C, JA = 34C/W EXPOSED PAD (PIN 39) IS GND, MUST BE SOLDERED TO PCB CH5 13 14 15 16 17 18 19 VREF45+ VREF45- CH5 CH4 VREF23+ CH3 VREF23- 13 14 15 16 17 18 19 ORDER INFORMATION 25 ADCINP VREF01 10 + CH4 VREF01 10 VREF23+ - 26 ADCINN 39 VREF23_ 39 COM 7 UHF PACKAGE 38-LEAD (5mm x 7mm) PLASTIC QFN TJMAX = 125C, JA = 34C/W EXPOSED PAD (PIN 39) IS GND, MUST BE SOLDERED TO PCB http://www.linear.com/product/LTC2446#orderinfo LEAD FREE FINISH TAPE AND REEL PART MARKING PACKAGE DESCRIPTION TEMPERATURE RANGE LTC2446CUHF#PBF LTC2446CUHF#TRPBF 2446 38-LEAD (5mm x 7mm) PLASTIC QFN 0C to 70C LTC2446IUHF#PBF LTC2446IUHF#TRPBF 2446 38-LEAD (5mm x 7mm) PLASTIC QFN -40C to 85C LTC2447CUHF#PBF LTC2447CUHF#TRPBF 2447 38-LEAD (5mm x 7mm) PLASTIC QFN 0C to 70C LTC2447IUHF#PBF LTC2447IUHF#TRPBF 2447 38-LEAD (5mm x 7mm) PLASTIC QFN -40C to 85C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/. Some packages are available in 500 unit reels through designated sales channels with #TRMPBF suffix. 24467fb 2 For more information www.linear.com/LTC2446 LTC2446/LTC2447 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Notes 3, 4) PARAMETER CONDITIONS Resolution (No Missing Codes) 0.1V VREF VCC, -0.5 * VREF VIN 0.5 * VREF, (Note 5) Integral Nonlinearity VCC = 5V, REF+ = 5V, REF- = GND, VINCM = 2.5V, (Note 6) REF+ = 2.5V, REF- = GND, VINCM = 1.25V, (Note 6) 2.5V REF+ VCC, REF- = GND, GND IN+ = IN- VCC(Note 12) 2.5V REF+ VCC, REF- = GND, GND IN+ = IN- VCC REF+ = 5V, REF- = GND, IN+ = 3.75V, IN- = 1.25V REF+ = 2.5V, REF- = GND, IN+ = 1.875V, IN- = 0.625V Offset Error Offset Error Drift Positive Full-Scale Error MIN l TYP MAX UNITS 24 Bits l 5 3 15 ppm of VREF ppm of VREF l 2.5 5 V 50 50 ppm of VREF ppm of VREF 20 nV/C 10 10 l l Positive Full-Scale Error Drift 2.5V REF+ VCC, REF- = GND, IN+ = 0.75REF+, IN- = 0.25 * REF+ Negative Full-Scale Error REF+ = 5V, REF- = GND, IN+ = 1.25V, IN- = 3.75V REF+ = 2.5V, REF- = GND, IN+ = 0.625V, IN- = 1.875V Negative Full-Scale Error Drift 2.5V REF+ VCC, REF- = GND, IN+ = 0.25 * REF+, IN- = 0.75 * REF+ 0.2 ppm of VREF/C Total Unadjusted Error 5V VCC 5.5V, REF+ = 2.5V, REF- = GND, VINCM = 1.25V 5V VCC 5.5V, REF+ = 5V, REF- = GND, VINCM = 2.5V REF+ = 2.5V, REF- = GND, VINCM = 1.25V, (Note 6) 15 15 15 ppm of VREF ppm of VREF ppm of VREF Input Common Mode Rejection DC 2.5V REF+ VCC, REF- = GND, GND IN- = IN+ VCC 120 dB 0.2 ppm of VREF/C 10 10 l l 50 50 ppm of VREF ppm of VREF ANALOG INPUT AND REFERENCE The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 3) SYMBOL PARAMETER IN+ Absolute/Common Mode IN+ Voltage CONDITIONS l GND - 0.3V MIN VCC + 0.3V V IN- Absolute/Common Mode IN- Voltage l GND - 0.3V VCC + 0.3V V VIN Input Differential Voltage Range (IN+ - IN-) l -VREF/2 VREF/2 V REF+ Absolute/Common Mode REF+ Voltage l 0.1 VCC V REF- Absolute/Common Mode REF- Voltage l GND VCC - 0.1V V VREF Reference Differential Voltage Range (REF+ - REF-) l 0.1 VCC V CS(IN+) IN+ Sampling Capacitance CS(IN-) IN- Sampling Capacitance 2 pF CS(REF+) REF+ Sampling Capacitance 2 pF CS(REF-) REF- Sampling Capacitance MUX Break-Before-Make MUX Off Isolation -15 1 pF 15 Varies, See Applications Section VIN = 2VP-P DC to 1.8MHz UNITS pF 2 ISAMPLE(IN+, IN-, REF+, REF-) Average Input/Reference Current During Sampling tOPEN MAX 2 IDC_LEAK(IN+, IN-, REF+, REF-) Leakage Current, Inputs and Reference CS = VCC, IN+ = GND, IN- = GND, l REF+ = 5V, REF- = GND QIRR TYP nA nA 50 ns 120 dB 24467fb For more information www.linear.com/LTC2446 3 LTC2446/LTC2447 DIGITAL INPUTS AND DIGITAL OUTPUTS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 3) SYMBOL PARAMETER CONDITIONS MIN VIH High Level Input Voltage CS, FO, SDI 4.5V VCC 5.5V l VIL Low Level Input Voltage CS, FO, SDI 4.5V VCC 5.5V l VIH High Level Input Voltage SCK 4.5V VCC 5.5V (Note 8) l VIL Low Level Input Voltage SCK 4.5V VCC 5.5V (Note 8) l IIN Digital Input Current CS, FO, EXT, SDI 0V VIN VCC l IIN Digital Input Current SCK 0V VIN VCC (Note 8) l CIN Digital Input Capacitance CS, FO, SDI CIN Digital Input Capacitance SCK (Note 8) VOH High Level Output Voltage SDO, BUSY IO = -800A l VOL Low Level Output Voltage SDO, BUSY IO = 1.6mA l VOH High Level Output Voltage SCK IO = -800A (Note 9) l VOL Low Level Output Voltage SCK IO = 1.6mA (Note 9) l IOZ Hi-Z Output Leakage SDO l TYP MAX UNITS 2.5 V 0.8 V 2.5 V 0.8 V -10 10 A -10 10 A 10 pF 10 pF VCC - 0.5V V 0.4 V VCC - 0.5V V -10 0.4 V 10 A POWER REQUIREMENTS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 3) SYMBOL PARAMETER VCC Supply Voltage ICC Supply Current Conversion Mode Sleep Mode CONDITIONS MIN l CS = 0V (Note 7) CS = VCC (Note 7) TYP 4.5 8 8 l l MAX UNITS 5.5 V 11 30 mA A TIMING CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 3) SYMBOL PARAMETER CONDITIONS MIN TYP MAX fEOSC External Oscillator Frequency Range l 0.1 12 tHEO External Oscillator High Period l 25 10000 tLEO External Oscillator Low Period tCONV Conversion Time fISCK Internal SCK Frequency l 25 OSR = 256 OSR = 32768 l l 0.99 126 External Oscillator, 1x Mode (Notes 10, 13) l Internal Oscillator (Note 9) External Oscillator (Notes 9, 10) l 1.13 145 0.9 fEOSC/10 MHz ns 10000 ns 1.33 170 ms ms 40 * OSR + 178 fEOSC (KHz) 0.8 UNITS ms 1 MHz Hz 24467fb 4 For more information www.linear.com/LTC2446 LTC2446/LTC2447 TIMING CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 3) SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS DISCK Internal SCK Duty Cycle (Note 9) l fESCK External SCK Frequency Range (Note 8) l tLESCK External SCK Low Period (Note 8) l 25 ns tHESCK External SCK High Period (Note 8) l 25 ns tDOUT_ISCK Internal SCK 32-Bit Data Output Time Internal Oscillator (Notes 9, 11) External Oscillator (Notes 9, 10) l l 41.6 tDOUT_ESCK External SCK 32-Bit Data Output Time (Note 8) l t1 CS to SDO Low Z (Note 12) l 0 t2 CS to SDO High Z (Note 12) l 0 t3 CS to SCK (Note 9) t4 CS to SCK (Notes 8, 12) tKQMAX SCK to SDO Valid tKQMIN SDO Hold After SCK t5 t6 t7 SDI Setup Before SCK (Note 5) l 10 ns t8 SDI Hold After SCK (Note 5) l 10 ns 45 % 20 MHz 30.9 s s 25 ns 32/fESCK s 25 5 l ns 25 l 15 SCK Setup Before CS l 50 SCK Hold After CS l (Note 5) ns s 25 l Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: All voltage values are with respect to GND. Note 3: VCC = 4.5V to 5.5V unless otherwise specified. VREF = REF+ - REF-, VREFCM = (REF+ + REF-)/2; REF+ is the positive reference input, REF- is the negative reference input; VIN = IN+ - IN-, VINCM = (IN+ + IN-)/2. Note 4: FO pin tied to GND or to external conversion clock source with fEOSC = 10MHz unless otherwise specified. Note 5: Guaranteed by design, not subject to test. Note 6: Integral nonlinearity is defined as the deviation of a code from a straight line passing through the actual endpoints of the transfer curve. The deviation is measured from the center of the quantization band. 35.3 320/fEOSC 55 ns ns ns 50 ns Note 7: The converter uses the internal oscillator. Note 8: The converter is in external SCK mode of operation such that the SCK pin is used as a digital input. The frequency of the clock signal driving SCK during the data output is fESCK and is expressed in Hz. Note 9: The converter is in internal SCK mode of operation such that the SCK pin is used as a digital output. In this mode of operation, the SCK pin has a total equivalent load capacitance of CLOAD = 20pF. Note 10: The external oscillator is connected to the FO pin. The external oscillator frequency, fEOSC, is expressed in Hz. Note 11: The converter uses the internal oscillator. FO = 0V. Note 12: Guaranteed by design and test correlation. Note 13: There is an internal reset that adds an additional 5 to 15 fO cycles to the conversion time. PIN FUNCTIONS GND (Pins 1, 4, 5, 6, 31, 32, 33): Ground. Multiple ground pins internally connected for optimum ground current flow and VCC decoupling. Connect each one of these pins to a common ground plane through a low impedance connection. All seven pins must be connected to ground for proper operation. BUSY (Pin 2): Conversion in Progress Indicator. This pin is HIGH while the conversion is in progress and goes LOW indicating the conversion is complete and data is ready. It remains LOW during the sleep and data output states. At the conclusion of the data output state, it goes HIGH indicating a new conversion has begun. EXT (Pin 3): Internal/External SCK Selection Pin. This pin is used to select internal or external SCK for outputting/inputting data. If EXT is tied low, the device is in the external SCK mode and data is shifted out of the device under the control of a user applied serial clock. If EXT is tied high, the internal serial clock mode is selected. The device generates its own SCK signal and outputs this on the SCK pin. A framing signal BUSY (Pin 2) goes low indicating data is being output. 24467fb For more information www.linear.com/LTC2446 5 LTC2446/LTC2447 PIN FUNCTIONS COM (Pin 7): The common negative input (IN-) for all single-ended multiplexer configurations. The voltage on CH0-CH7 and COM pins can have any value between GND - 0.3V to VCC + 0.3V. Within these limits, the two selected inputs (IN+ and IN-) provide a bipolar input range (VIN = IN+ - IN-) from -0.5 * VREF to 0.5 * VREF. Outside this input range, the converter produces unique over-range and under-range output codes. CH0 to CH7 (Pins 8, 9, 12, 13, 16, 17, 20, 21): Analog Inputs. May be programmed for Single-ended or Differential mode. VREF01+ (Pin 11), VREF01- (Pin 10) VREF23+ (Pin 15), VREF23- (Pin 14), VREF45+ (Pin 19), VREF45- (Pin 18), VREF67+ (Pin 23), VREF67- (Pin 22): Differential Reference Inputs. The voltage on these pins can be anywhere between 0V and VCC as long as the positive reference input (VEF01+, VREF23+, VREF45+, VREF67+) is greater than the corresponding negative reference input (VREF01-, VREF23-, VREF45-, VREF67-) by at least 100mV. NC (Pins 24, 25, 26, 27): LTC2446 No Connect. These pins can either be tied to ground or left floating. MUXOUTP (Pin 24): LTC2447 Positive Input Channel Multiplexer Output. Used to drive the input to an external buffer/amplifier for the selected positive input signal (IN+). ADCINP (Pin 25): LTC2447 Positive ADC Input. Tie to output of buffer/amplifier driven by MUXOUTP. ADCINN (Pin 26): LTC2447 Negative ADC Input. Tie to output of buffer/amplifier driven by MUXOUTN. MUXOUTN (Pin 27): LTC2447 Negative Input Channel Multiplexer Output. Used to drive the input to an external buffer/amplifier for the selected negative input signal (IN-). VCC (Pin 28): Positive Supply Voltage. Bypass to GND with a 10F tantalum capacitor in parallel with a 0.1F ceramic capacitor as close to the part as possible. VREFG+ (Pin 29), VREFG- (Pin 30): Global Reference Input. This differential reference input can be used for any input channel selected through a single bit in the digital input word. SDI (Pin 34): Serial Data Input. This pin is used to select the speed, 1x or 2x mode, resolution, input channel and reference input for the next conversion cycle. At initial power-up, the default mode of operation is CH0-CH1, VREF01, OSR of 256, and 1x mode. The serial data input contains an enable bit which determines if a new channel/ speed is selected. If this bit is low the following conversion remains at the same speed and selected channel. The serial data input is applied to the device under control of the serial clock (SCK) during the data output cycle. The first conversion following a new channel/speed is valid. FO (Pin 35): Frequency Control Pin. Digital input that controls the internal conversion clock. When FO is connected to VCC or GND, the converter uses its internal oscillator. CS (Pin 36): Active Low Chip Select. A LOW on this pin enables the SDO digital output and wakes up the ADC. Following each conversion the ADC automatically enters the sleep mode and remains in this low power state as long as CS is HIGH. A LOW-to-HIGH transition on CS during the Data Output aborts the data transfer and starts a new conversion. SDO (Pin 37): Three-State Digital Output. During the data output period, this pin is used as serial data output. When the chip select CS is HIGH (CS = VCC) the SDO pin is in a high impedance state. During the conversion and sleep periods, this pin is used as the conversion status output. The conversion status can be observed by pulling CS LOW. This signal is HIGH while the conversion is in progress and goes LOW once the conversion is complete. SCK (Pin 38): Bidirectional Digital Clock Pin. In internal serial clock operation mode, SCK is used as a digital output for the internal serial interface clock during the data output period. In the external serial clock operation mode, SCK is used as the digital input for the external serial interface clock during the data output period. The serial clock operation mode is determined by the logic level applied to the EXT pin. Exposed Pad (Pin 39): Ground. The exposed pad on the bottom of the package must be soldered to the PCB ground. For Prototyping purposes, this pin may remain floating. 24467fb 6 For more information www.linear.com/LTC2446 LTC2446/LTC2447 FUNCTIONAL BLOCK DIAGRAM VCC * * * VREF67+ VREF67- VREFG+ VREFG- CH0 CH1 * * * CH7 COM INTERNAL OSCILLATOR INPUT/REFERENCE MUX VREF01+ VREF01- REF+ FO (INT/EXT) AUTOCALIBRATION AND CONTROL REF - IN + DIFFERENTIAL 3RD ORDER MODULATOR IN - SDI SCK SDO CS SERIAL INTERFACE DECIMATING FIR GND ADDRESS 24467 F01 Figure 1. Functional Block Diagram TEST CIRCUITS VCC 1.69k SDO SDO 1.69k Hi-Z TO VOH VOL TO VOH VOH TO Hi-Z CLOAD = 20pF CLOAD = 20pF Hi-Z TO VOL VOH TO VOL VOL TO Hi-Z 24467 TA03 APPLICATIONS INFORMATION POWER UP IN+=CH0, IN-=CH1 REF+ = VREFO1+, REF- = VREF01- OSR=256,1x MODE CONVERTER OPERATION Converter Operation Cycle The LTC2446/LTC2447 are multichannel, multireference high speed, delta-sigma analog-to-digital converters with an easy to use 3- or 4-wire serial interface (see Figure 1). Their operation is made up of three states. The converter operating cycle begins with the conversion, followed by the low power sleep state and ends with the data output/ input (see Figure 2). The 4-wire interface consists of serial data input (SDI), serial data output (SDO), serial clock (SCK) and chip select (CS). The interface, timing, operation cycle and data out format is compatible with Linear's entire family of converters. Initially, the LTC2446/LTC2447 perform a conversion. Once the conversion is complete, the device enters thesleep state. 24467 TA04 CONVERT SLEEP CS = LOW AND SCK NO YES CHANNEL SELECT REFERENCE SELECT SPEED SELECT DATA OUTPUT 24467 F02 Figure 2. LTC2446/LTC2447 State Transition Diagram 24467fb For more information www.linear.com/LTC2446 7 LTC2446/LTC2447 APPLICATIONS INFORMATION While in this sleep state, power consumption is reduced below 10A. The part remains in the sleep state as long as CS is HIGH. The conversion result is held indefinitely in a static shift register while the converter is in the sleep state. Once CS is pulled LOW, the device begins outputting the conversion result. There is no latency in the conversion result while operating in the 1x mode. The data output corresponds to the conversion just performed. This result is shifted out on the serial data out pin (SDO) under the control of the serial clock (SCK). Data is updated on the falling edge of SCK allowing the user to reliably latch data on the rising edge of SCK (see Figure 3). The data output state is concluded once 32 bits are read out of the ADC or when CS is brought HIGH. The device automatically initiates a new conversion and the cycle repeats. Through timing control of the CS, SCK and EXT pins, the LTC2446/LTC2447 offer several flexible modes of operation (internal or external SCK). These various modes do not require programming configuration registers; moreover, they do not disturb the cyclic operation described above. These modes of operation are described in detail in the Serial Interface Timing Modes section. Ease of Use The LTC2446/LTC2447 data output has no latency, filter settling delay or redundant data associated with the conversion cycle while operating in the 1x mode. There is a one-to-one correspondence between the conversion and the output data. Therefore, multiplexing multiple analog voltages and references is easy. Speed/resolution adjustments may be made seamlessly between two conversions without settling errors. The LTC2446/LTC2447 perform offset and full-scale calibrations every conversion cycle. This calibration is transparent to the user and has no effect on the cyclic operation described above. The advantage of continuous calibration is extreme stability of offset and full-scale readings with respect to time, supply voltage change and temperature drift. Power-Up Sequence The LTC2446/LTC2447 automatically enter an internal reset state when the power supply voltage VCC drops 8 below approximately 2.2V. This feature guarantees the integrity of the conversion result and of the serial interface mode selection. When the VCC voltage rises above this critical threshold, the converter creates an internal power-on-reset (POR) signal with a duration of approximately 0.5ms. The POR signal clears all internal registers. The conversion immediately following a POR is performed on the input channel IN+ = CH0, IN- = CH1, REF+ = VREF01+, REF- VREF01- at an OSR = 256 in the 1x mode. Following the POR signal, the LTC2446/LTC2447 start a normal conversion cycle and follow the succession of states described above. The first conversion result following POR is accurate within the specifications of the device if the power supply voltage is restored within the operating range (4.5V to 5.5V) before the end of the POR time interval. Reference Voltage Range These converters accept truly differential external reference voltages. Each set of five reference inputs may be independently driven to any common mode voltage over the entire supply range of the device (GND to VCC). For correct converter operation, each positive reference pin REF+ (VREF01+, VREF23+, VREF45+, VREF67+, VREFG+) must be more positive than its corresponding negative reference pin REF- (VREF01-, VREF23-, VREF45-, VREF67-, VREFG-) by at least 100mV. The LTC2446/LTC2447 can accept a differential reference from 0.1V to VCC on each set of reference input pins. The converter output noise is determined by the thermal noise of the front-end circuits, and as such, its value in microvolts is nearly constant with reference voltage. A decrease in reference voltage will not significantly improve the converter's effective resolution. On the other hand, a reduced reference voltage will improve the converter's overall INL performance. Input Voltage Range Refer to Figure 4. The analog input is truly differential with an absolute/common mode range for the CH0-CH7 and COM input pins extending from GND - 0.3V to VCC + 0.3V. Outside these limits, the ESD protection devices begin to turn on and the errors due to input leakage current increase For more information www.linear.com/LTC2446 24467fb LTC2446/LTC2447 APPLICATIONS INFORMATION rapidly. Within these limits, the LTC2446/LTC2447 convert the bipolar differential input signal, VIN = IN+ - IN- (where IN+ and IN- are the selected input channels), from - FS = -0.5 * VREF to +FS = 0.5 * VREF where VREF = REF+ - REF - (REF+ and REF- are the selected references). Outside this range, the converter indicates the overrange or the underrange condition using distinct output codes. Bit 31 (first output bit) is the end of conversion (EOC) indicator. This bit is available at the SDO pin during the conversion and sleep states whenever the CS pin is LOW. This bit is HIGH during the conversion and goes LOW when the conversion is complete. MUXOUT/ADCIN Bit 29 (third output bit) is the conversion result sign indicator (SIG). If VIN is >0, this bit is HIGH. If VIN is <0, this bit is LOW. There are two differences between the LTC2446 and the LTC2447. The first is the RMS noise performance. For a given OSR, the LTC2447 noise level is approximately 2 times lower (0.5 effective bits) than that of the LTC2446. The second difference is the LTC2447 includes MUXOUT/ ADCIN pins. These pins enable an external buffer or gain block to be inserted between the selected input channel of the multiplexer and the input to the ADC. Since the buffer is driven by the output of the multiplexer, only one circuit is required for all 8 input channels. Additionally, the transparent calibration feature of the LTC244X family automatically removes the offset errors of the external buffer. In order to achieve optimum performance, the MUXOUT and ADCIN pins should not be shorted together. In applications where the MUXOUT and ADCIN need to be shorted together, the LTC2446 should be used because the MUXOUT and ADCIN are internally connected for optimum performance. Output Data Format The LTC2446/LTC2447 serial output data stream is 32 bits long. The first 3 bits represent status information indicating the sign and conversion state. The next 24 bits are the conversion result, MSB first. The remaining 5 bits are sub LSBs beyond the 24-bit level that may be included in averaging or discarded without loss of resolution. In the case of ultrahigh resolution modes, more than 24 effective bits of performance are possible (see Table 4). Under these conditions, sub LSBs are included in the conversion result and represent useful information beyond the 24-bit level. The third and fourth bit together are also used to indicate an underrange condition (the differential input voltage is below -FS) or an overrange condition (the differential input voltage is above +FS). Bit 30 (second output bit) is a dummy bit (DMY) and is always LOW. Bit 28 (fourth output bit) is the most significant bit (MSB) of the result. This bit in conjunction with Bit 29 also provides the underrange or overrange indication. If both Bit 29 and Bit 28 are HIGH, the differential input voltage is above +FS. If both Bit 29 and Bit 28 are LOW, the differential input voltage is below -FS. The function of these bits is summarized in Table 1. Table 1. LTC2446/LTC2447 Status Bits INPUT RANGE BIT 31 EOC BIT 30 DMY BIT 29 SIG BIT 28 MSB VIN 0.5 * VREF 0 0 1 1 0V VIN < 0.5 * VREF 0 0 1 0 -0.5 * VREF VIN < 0V 0 0 0 1 VIN < -0.5 * VREF 0 0 0 0 Bits 28-5 are the 24-bit conversion result MSB first. Bit 5 is the least significant bit (LSB). Bits 4-0 are sub LSBs below the 24-bit level. Bits 4-0 may be included in averaging or discarded without loss of resolution. Data is shifted out of the SDO pin under control of the serial clock (SCK), see Figure 3. Whenever CS is HIGH, SDO remains high impedance and SCK is ignored. In order to shift the conversion result out of the device, CS must first be driven LOW. EOC is seen at the SDO pin of the device once CS is pulled LOW. EOC changes real time from HIGH to LOW at the completion of a conversion. This signal may be used as an interrupt for an external microcontroller. Bit 31 (EOC) can be captured on the first rising edge of SCK. Bit 30 is shifted out of the device on the first falling edge of SCK. The final data bit (Bit 0) is24467fb For more information www.linear.com/LTC2446 9 LTC2446/LTC2447 APPLICATIONS INFORMATION CS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 32 SCK SDI SDO 1 Hi-Z 0 EN SGL ODD GLBL A1 A0 OSR3 OSR2 OSR1 BIT 31 BIT 30 BIT 29 BIT 28 BIT 27 BIT 26 BIT 25 BIT 24 BIT 23 BIT 22 BIT 21 EOC "0" SIG OSR0 TWOX BIT 20 BIT 19 BIT 0 LSB MSB BUSY Hi-Z 24467 F03 Figure 3. SDI Speed/Resolution, Channel Selection, and Data Output Timing shifted out on the falling edge of the 31st SCK and may be latched on the rising edge of the 32nd SCK pulse. On the falling edge of the 32nd SCK pulse, SDO goes HIGH indicating the initiation of a new conversion cycle. This bit serves as EOC (Bit 31) for the next conversion cycle. Table 2 summarizes the output data format. As long as the voltage on the IN+ and IN- pins is maintained within the - 0.3V to (VCC + 0.3V) absolute maximum operating range, a conversion result is generated for any differential input voltage VIN from -FS = -0.5 * VREF to +FS = 0.5 * VREF. For differential input voltages greater than +FS, the conversion result is clamped to the value corresponding to the +FS + 1LSB. For differential input voltages below -FS, the conversion result is clamped to the value corresponding to -FS - 1LSB. SERIAL INTERFACE PINS The LTC2446/LTC2447 transmit the conversion results and receive the start of conversion command through a synchronous 3- or 4-wire interface. During the conversion and sleep states, this interface can be used to assess the converter status and during the data output state it is used to read the conversion result and program the speed, resolution and input channel. Table 2. LTC2446/LTC2447 Output Data Format Differential Input Voltage VIN* Bit 31 EOC Bit 30 DMY Bit 29 SIG Bit 28 MSB Bit 27 Bit 26 Bit 25 ... Bit 0 VIN* 0.5 * VREF** 0 0 1 1 0 0 0 ... 0 0.5 * VREF** - 1LSB 0 0 1 0 1 1 1 ... 1 0.25 * VREF** 0 0 1 0 1 0 0 ... 0 0.25 * VREF** - 1LSB 0 0 1 0 0 1 1 ... 1 0 0 0 1 0 0 0 0 ... 0 -1LSB 0 0 0 1 1 1 1 ... 1 -0.25 * VREF** 0 0 0 1 1 0 0 ... 0 -0.25 * VREF** - 1LSB 0 0 0 1 0 1 1 ... 1 -0.5 * VREF** 0 0 0 1 0 0 0 ... 0 0 0 0 0 1 1 1 ... 1 VIN* < -0.5 * VREF** *The differential input voltage VIN = IN+ - IN-. **The differential reference voltage VREF = REF+ - REF -. 24467fb 10 For more information www.linear.com/LTC2446 LTC2446/LTC2447 APPLICATIONS INFORMATION Serial Clock Input/Output (SCK) The serial clock signal present on SCK (Pin 38) is used to synchronize the data transfer. Each bit of data is shifted out the SDO pin on the falling edge of the serial clock. In the Internal SCK mode of operation, the SCK pin is an output and the LTC2446/LTC2447 create their own serial clock. In the External SCK mode of operation, the SCK pin is used as input. The internal or external SCK mode is selected by tying EXT (Pin 3) LOW for external SCK and HIGH for internal SCK. Serial Data Output (SDO) The serial data output pin, SDO (Pin 37), provides the result of the last conversion as a serial bit stream (MSB first) during the data output state. In addition, the SDO pin is used as an end of conversion indicator during the conversion and sleep states. When CS (Pin 36) is HIGH, the SDO driver is switched to a high impedance state. This allows sharing the serial interface with other devices. If CS is LOW during the convert or sleep state, SDO will output EOC. If CS is LOW during the conversion phase, the EOC bit appears HIGH on the SDO pin. Once the conversion is complete, EOC goes LOW. The device remains in the sleep state until the first rising edge of SCK occurs while CS = LOW. Chip Select Input (CS) The active LOW chip select, CS (Pin 36), is used to test the conversion status and to enable the data output transfer as described in the previous sections. In addition, the CS signal can be used to trigger a new conversion cycle before the entire serial data transfer has been completed. The LTC2446/LTC2447 will abort any serial data transfer in progress and start a new conversion cycle anytime a LOW-to-HIGH transition is detected at the CS pin after the converter has entered the data output state. Serial Data Input (SDI) The serial data input (SDI, Pin 34) is used to select the speed/resolution input channel and reference of the LTC2446/LTC2447. SDI is programmed by a serial input data stream under the control of SCK during the data output cycle, see Figure 3. Initially, after powering up, the device performs a conversion with IN+ = CH0, IN- = CH1, REF+ = VREF01+, REF- = VREF01-, OSR = 256 (output rate nominally 880Hz), and 1x speed mode (no latency). Once this first conversion is complete, the device enters the sleep state and is ready to output the conversion result and receive the serial data input stream programming the speed/resolution, input channel and reference for the next conversion. At the conclusion of each conversion cycle, the device enters this state. In order to change the speed/resolution, reference or input channel, the first 3 bits shifted into the device are 101. This is compatible with the programming sequence of the LTC2414/LTC2418/LTC2444/LTC2445/LTC2448/ LTC2449. If the sequence is set to 000 or 100, the following input data is ignored (don't care) and the previously selected speed/resolution, channel and reference remain valid for the next conversion. Combinations other than 101, 100, and 000 of the 3 control bits should be avoided. If the first 3 bits shifted into the device are 101, then the following 5 bits select the input channel/reference for the following conversion (see Table 3). The next 5 bits select the speed/resolution and mode 1x (no latency) 2x (double output rate with one conversion latency), see Table 4. If these 5 bits are set to all 0's, the previous speed remains selected for the next conversion. This is useful in applications requiring a fixed output rate/resolution but need to change the input channel or reference. In this case, the timing and input sequence is compatible with the LTC2414/LTC2418. When an update operation is initiated (the first 3 bits are 101) the next 5 bits are the channel/reference address. The first bit, SGL, determines if the input selection is differential (SGL = 0) or single-ended (SGL = 1). For SGL = 0, two adjacent channels can be selected to form a differential input. For SGL = 1, one of 8 channels is selected as the positive input. The negative input is COM for all single ended operations. The global VREF bit (GLBL) is used to determine which reference is selected. GLBL = 0 selects the individual reference slaved to a given channel. Each set of channels has a corresponding differential input reference. If GLBL = 1, a global reference VREFG+/VREFG- is selected. The global reference input may be used for any input channel selected. Table 3 shows a summary of input/reference selection. The remaining bits (ODD, A1, A0) determine which channel is selected. 24467fb For more information www.linear.com/LTC2446 11 LTC2446/LTC2447 APPLICATIONS INFORMATION Table 3. Channel Selection for the LTC2446/LTC2447 MUX ADDRESS ODD/ SGL SIGN GLBL A1 CHANNEL INPUT A0 0 1 IN+ IN- 0* 0 0 0 0 0 0 0 0 1 0 0 0 1 0 0 0 0 1 1 0 1 0 0 0 0 1 0 0 1 0 1 0 1 0 0 1 0 1 1 1 0 0 0 0 1 0 0 0 1 1 0 0 1 0 1 0 0 1 1 1 1 0 0 0 1 1 0 0 1 1 1 0 1 0 1 1 0 1 1 0 0 1 0 0 0 0 1 0 1 0 0 1 1 0 0 0 1 1 1 0 1 1 0 0 0 1 1 0 1 0 1 1 1 0 0 1 1 1 1 1 0 1 0 0 1 0 1 0 1 1 0 1 1 0 1 0 1 1 1 1 1 1 0 0 1 1 1 0 1 1 1 1 1 0 1 1 1 1 1 2 IN+ 3 4 5 REFERENCE INPUT 6 REF- 23+ 23- 45+ 45- 67+ 67- G+ G- REF+ REF- REF+ REF- IN- REF+ REF- IN+ REF+ REF- IN- IN+ REF+ REF- IN- IN+ REF+ REF- IN- IN+ IN+ REF+ REF- IN- REF+ REF- IN+ IN- IN+ REF+ REF- IN- IN+ REF+ REF- IN- IN+ REF+ REF- IN- REF+ REF- IN+ IN- IN+ IN- IN+ IN- IN- REF+ REF- REF+ REF- REF+ REF- REF+ REF- IN+ IN- REF+ REF- IN+ IN- REF+ REF- IN+ IN- 01- REF+ IN- IN+ IN+ COM 01+ IN- IN+ IN- 7 IN- REF+ REF- IN+ REF+ REF- IN- IN+ REF+ REF- IN- IN+ REF+ REF- IN- IN+ IN+ IN+ IN+ IN+ IN+ IN+ IN+ IN+ REF+ REF- IN- REF+ REF- IN- REF+ REF- IN- REF+ REF- IN- REF+ REF- IN- REF+ REF- IN- REF+ REF- IN- REF+ REF- IN- REF+ REF- *Default at power up 24467fb 12 For more information www.linear.com/LTC2446 LTC2446/LTC2447 APPLICATIONS INFORMATION Table 4. LTC2446/LTC2447 Speed/Resolution Selection RMS RMS NOISE NOISE ENOB ENOB LTC2446 LTC2447 LTC2446 LTC2447 OSR3 OSR2 OSR1 OSR0 TWOX OSR LATENCY 0 0 0 0 0 0 0 0 1 0 23V 23V 17 17 64 None 0 0 1 0 0 4.4V 3.5V 20.1 20.1 128 None Keep Previous Speed/Resolution 0 0 1 1 0 2.8V 2V 20.8 21.3 256 None 0 1 0 0 0 2V 1.4V 21.3 21.8 512 None 0 1 0 1 0 1.4V 1V 21.8 22.4 1024 None 0 1 1 0 0 1.1V 750nV 22.1 22.9 2048 None 0 1 1 1 0 720nV 510nV 22.7 23.4 4096 None 1 0 0 0 0 530nV 375nV 23.2 24 8192 None 1 0 0 1 0 350nV 250nV 23.8 24.4 16384 None 1 1 1 1 0 280nV 200nV 24.1 24.6 32768 none 0 0 0 0 1 0 0 0 1 1 23V 23V Keep Previous Speed/Resolution 17 17 64 1 Cycle 0 0 1 0 1 4.4V 3.5V 20.1 20.1 128 1 Cycle 0 0 1 1 1 2.8V 2V 20.8 21.3 256 1 Cycle 0 1 0 0 1 2V 1.4V 21.3 21.8 512 1 Cycle 0 1 0 1 1 1.4V 1V 21.8 22.4 1024 1 Cycle 0 1 1 0 1 1.1V 750nV 22.1 22.9 2048 1 Cycle 0 1 1 1 1 720nV 510nV 22.7 23.4 4096 1 Cycle 1 0 0 0 1 530nV 375nV 23.2 24 8192 1 Cycle 1 0 0 1 1 350nV 250nV 23.8 24.4 16384 1 Cycle 1 1 1 1 1 280nV 200nV 24.1 24.6 32768 1 Cycle VCC + 0.3V VCC VREF 2 GND -0.3V VCC VREF 2 -VREF 2 VREF 2 -VREF 2 GND (a) Arbitrary (b) Fully Differential VCC VCC VREF 2 VREF 2 -VREF 2 GND (c) Pseudo Differential Bipolar IN- or COM Biased Selected IN+ Ch Selected IN- Ch or COM -0.3V GND -0.3V (d) Pseudo-Differential Unipolar IN- or COM Grounded Figure 4. Input Range For more information www.linear.com/LTC2446 24467 F04 24467fb 13 LTC2446/LTC2447 APPLICATIONS INFORMATION Speed Multiplier Mode In addition to selecting the speed/resolution, a speed multiplier mode is used to double the output rate while maintaining the selected resolution. The last bit of the 5bit speed/resolution control word (TWOX, see Table 4) determines if the output rate is 1x (no speed increase) or 2x (double the selected speed). While operating in the 1x mode, the device combines two internal conversions for each conversion result in order to remove the ADC offset. Every conversion cycle, the offset and offset drift are transparently calibrated greatly simplifying the user interface. The conversion result has no latency. The first conversion following a newly selected speed/resolution and/or input/reference is valid. This is identical to the operation of the LTC2440, LTC2444, LTC2445, LTC2448, LTC2449, LTC2414 and LTC2418. While operating in the 2x mode, the device performs a running average of the last two conversion results. This automatically removes the offset and drift of the device while increasing the output rate by 2x. The resolution (noise) remains the same as the 1x mode. If a new channel/ reference is selected, the conversion result is valid for all conversions after the first conversion (one cycle latency). If a new speed/resolution is selected, the first conversion result is valid but the resolution (noise) is a function of the running average. All subsequent conversion results are valid. If the mode is changed from either 1x to 2x or 2x to 1x without changing the resolution or channel, the first conversion result is valid. If an external buffer/amplifier circuit is used for the LTC2447, the 2x mode can be used to increase the settling time of the amplifier between readings. While operating in the 2x mode, the multiplexer output (input to the external buffer/amplifier) is switched at the end of each conversion cycle. Prior to concluding the data out/in cycle, the analog multiplexer output is switched. This occurs at the end of the conversion cycle (just prior to the data output cycle) for auto calibration. The time required to read the conversion enables more settling time for the external buffer/amplifier. The offset/offset drift of the external amplifiers are automatically removed by the converter's auto calibration sequence for both the 1x and 2x speed modes. While operating in the 1x mode, if a new input channel/ reference is selected the multiplexer is switched on the falling edge of the 14th SCK (once the complete data input word is programmed). The remaining data output sequence time can be used to allow the external buffer/ amplifier to settle. BUSY The BUSY output (Pin 2) is used to monitor the state of conversion, data output and sleep cycle. While the part is converting, the BUSY pin is HIGH. Once the conversion is complete, BUSY goes LOW indicating the conversion is complete and data out is ready. The part now enters the LOW power sleep state. BUSY remains LOW while data is shifted out of the device and SDI is shifted into the device. It goes HIGH at the conclusion of the data input/output cycle indicating a new conversion has begun. This rising edge may be used to flag the completion of the data read cycle. SERIAL INTERFACE TIMING MODES The LTC2446/LTC2447's 3- or 4-wire interface is SPI and MICROWIRE compatible. This interface offers several flexible modes of operation. These include internal/external serial clock, 3- or 4-wire I/O, single cycle conversion and autostart. The following sections describe each of these serial interface timing modes in detail. In all these cases, the converter can use the internal oscillator (FO = LOW) or an external oscillator connected to the FO pin. Refer to Table 5 for a summary. Table 5. LTC2446/LTC2447 Interface Timing Modes CONFIGURATION SCK SOURCE CONVERSION CYCLE CONTROL DATA OUTPUT CONTROL CONNECTION AND WAVEFORMS External SCK, Single Cycle Conversion External CS and SCK CS and SCK Figures 4, 5 External SCK, 3-Wire I/O External SCK SCK Figure 6 Internal SCK, Single Cycle Conversion Internal CS CS Figures 7, 8 Internal SCK, 3-Wire I/O, Continuous Conversion Internal Continuous Internal Figure 9 24467fb 14 For more information www.linear.com/LTC2446 LTC2446/LTC2447 APPLICATIONS INFORMATION External Serial Clock, Single Cycle Operation (SPI/MICROWIRE Compatible) When the device is in the sleep state (EOC = 0), its conversion result is held in an internal static shift register. The device remains in the sleep state until the first rising edge of SCK is seen. Data is shifted out the SDO pin on each falling edge of SCK. This enables external circuitry to latch the output on the rising edge of SCK. EOC can be latched on the first rising edge of SCK and the last bit of the conversion result can be latched on the 32nd rising edge of SCK. On the 32nd falling edge of SCK, the device begins a new conversion. SDO goes HIGH (EOC = 1) and BUSY goes HIGH indicating a conversion is in progress. This timing mode uses an external serial clock to shift out the conversion result and a CS signal to monitor and control the state of the conversion cycle, see Figure 5. The serial clock mode is selected by the EXT pin. To select the external serial clock mode, EXT must be tied low. The serial data output pin (SDO) is Hi-Z as long as CS is HIGH. At any time during the conversion cycle, CS may be pulled LOW in order to monitor the state of the converter. While CS is pulled LOW, EOC is output to the SDO pin. EOC = 1 (BUSY = 1) while a conversion is in progress and EOC = 0 (BUSY = 0) if the device is in the sleep state. Independent of CS, the device automatically enters the low power sleep state once the conversion is complete. At the conclusion of the data cycle, CS may remain LOW and EOC monitored as an end-of-conversion interrupt. Alternatively, CS may be driven HIGH setting SDO to Hi-Z and BUSY monitored for the completion of a conversion. 4.5V TO 5.5V 1F 28 29 30 11 USER SELECTABLE REFERENCES 0.1V TO VCC 10 24 23 8 9 ANALOG INPUTS 12 22 7 VCC = EXTERNAL OSCILLATOR = INTERNAL OSCILLATOR 35 FO LTC2446 REFG+ REFG- REF01+ - REF01 . .. REF67+ - REF67 34 SDI 38 SCK 4-WIRE SPI INTERFACE CH0 CH1 SDO CH2 . CS CH7 BUSY COM GND .. 37 36 2 1,4,5,6,31,32,33 CS TEST EOC TEST EOC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 32 SCK (EXTERNAL) SDI SDO 1 Hi-Z 0 EN SGL ODD GLBL A1 A0 OSR3 OSR2 OSR1 BIT 31 BIT 30 BIT 29 BIT 28 BIT 27 BIT 26 BIT 25 BIT 24 BIT 23 BIT 22 BIT 21 EOC "0" SIG OSR0 TWOX BIT 20 BIT 19 BIT 0 LSB MSB Hi-Z BUSY CONVERSION SLEEP DATA OUTPUT CONVERSION 24467 F05 Figure 5. External Serial Clock, Single Cycle Operation 24467fb For more information www.linear.com/LTC2446 15 LTC2446/LTC2447 APPLICATIONS INFORMATION data output sequence is aborted prior to the 13th rising edge of SCK, the new input data is ignored, and the previously selected speed/resolution and channel are used for the next conversion cycle. This is useful for systems not requiring all 32 bits of output data, aborting an invalid conversion cycle or synchronizing the start of a conversion. If a new channel is being programmed, the rising edge of CS must come after the 14th falling edge of SCK in order to store the data input sequence. As described above, CS may be pulled LOW at any time in order to monitor the conversion status on the SDO pin. Typically, CS remains LOW during the data output state. However, the data output state may be aborted by pulling CS HIGH anytime between the fifth falling edge and the 32nd falling edge of SCK, see Figure 6. On the rising edge of CS, the device aborts the data output state and immediately initiates a new conversion. Thirteen serial input data bits are required in order to properly program the speed/resolution and input/reference channel. If the 4.5V TO 5.5V 1F 28 29 30 11 USER SELECTABLE REFERENCES 0.1V TO VCC 10 24 23 8 9 ANALOG INPUTS 12 22 7 VCC = EXTERNAL OSCILLATOR = INTERNAL OSCILLATOR 35 FO LTC2446 REFG+ REFG- REF01+ - REF01 . .. REF67+ 34 SDI REF67- 38 SCK 4-WIRE SPI INTERFACE CH0 CH1 SDO CH2 . CS CH7 BUSY COM GND .. 37 36 2 1,4,5,6,31,32,33 CS 1 SCK (EXTERNAL) SDI 5 1 2 3 4 5 TEST EOC 6 DON'T CARE DON'T CARE DON'T CARE BIT 31 BIT 30 BIT 29 BIT 28 BIT 27 BIT 26 BIT 25 Hi-Z SDO EOC "0" SIG MSB Hi-Z BUSY CONVERSION DATA OUTPUT SLEEP CONVERSION DATA OUTPUT CONVERSION SLEEP 24467 F06 Figure 6. External Serial Clock, Reduced Output Data Length 24467fb 16 For more information www.linear.com/LTC2446 LTC2446/LTC2447 APPLICATIONS INFORMATION External Serial Clock, 3-Wire I/O controller indicating the conversion result is ready. EOC = 1 (BUSY = 1) while the conversion is in progress and EOC = 0 (BUSY = 0) once the conversion enters the low power sleep state. On the falling edge of EOC/BUSY, the conversion result is loaded into an internal static shift register. The device remains in the sleep state until the first rising edge of SCK. Data is shifted out the SDO pin on each falling edge of SCK enabling external circuitry to latch data on the rising edge of SCK. EOC can be latched on the first rising edge of SCK. On the 32nd falling edge of SCK, SDO and BUSY go HIGH (EOC = 1) indicating a new conversion has begun. This timing mode utilizes a 3-wire serial I/O interface. The conversion result is shifted out of the device by an externally generated serial clock (SCK) signal, see Figure 6. CS may be permanently tied to ground, simplifying the user interface or isolation barrier. The external serial clock mode is selected by tying EXT LOW. Since CS is tied LOW, the end-of-conversion (EOC) can be continuously monitored at the SDO pin during the convert and sleep states. Conversely, BUSY (Pin 2) may be used to monitor the status of the conversion cycle. EOC or BUSY may be used as an interrupt to an external 4.5V TO 5.5V 1F 28 29 30 11 USER SELECTABLE REFERENCES 0.1V TO VCC 10 24 23 8 9 ANALOG INPUTS 12 22 7 VCC = EXTERNAL OSCILLATOR = INTERNAL OSCILLATOR 35 FO LTC2446 REFG+ REFG- REF01+ - REF01 . .. REF67+ SDI REF67- SCK 34 38 3-WIRE SPI INTERFACE CH0 CH1 SDO CH2 . CS CH7 BUSY COM GND .. 37 36 2 1,4,5,6,31,32,33 CS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 32 SCK (EXTERNAL) SDI 1 DON'T CARE 0 EN SGL ODD GLBL A1 A0 OSR3 OSR2 OSR1 BIT 31 BIT 30 BIT 29 BIT 28 BIT 27 BIT 26 BIT 25 BIT 24 BIT 23 BIT 22 BIT 21 EOC SDO "0" SIG OSR0 TWOX DON'T CARE BIT 20 BIT 19 BIT 0 LSB MSB BUSY CONVERSION SLEEP DATA OUTPUT CONVERSION 24467 F07 Figure 7. External Serial Clock, CS = 0 Operation (3-Wire) 24467fb For more information www.linear.com/LTC2446 17 LTC2446/LTC2447 APPLICATIONS INFORMATION Internal Serial Clock, Single Cycle Operation conversion and goes LOW at the conclusion. It remains LOW until the result is read from the device. This timing mode uses an internal serial clock to shift out the conversion result and a CS signal to monitor and control the state of the conversion cycle, see Figure 8. When testing EOC, if the conversion is complete (EOC = 0), the device will exit the sleep state and enter the data output state if CS remains LOW. In order to prevent the device from exiting the low power sleep state, CS must be pulled HIGH before the first rising edge of SCK. In the internal SCK timing mode, SCK goes HIGH and the device begins outputting data at time tEOCtest after the falling edge of CS (if EOC = 0) or tEOCtest after EOC goes LOW (if CS is LOW during the falling edge of EOC). The value of tEOCtest is 500ns. If CS is pulled HIGH before time tEOCtest, the device remains in the sleep state. The conversion result is held in the internal static shift register. In order to select the internal serial clock timing mode, the EXT pin must be tied HIGH. The serial data output pin (SDO) is Hi-Z as long as CS is HIGH. At any time during the conversion cycle, CS may be pulled LOW in order to monitor the state of the converter. Once CS is pulled LOW, SCK goes LOW and EOC is output to the SDO pin. EOC = 1 while a conversion is in progress and EOC = 0 if the device is in the sleep state. Alternatively, BUSY (Pin 2) may be used to monitor the status of the conversion in progress. BUSY is HIGH during the 4.5V TO 5.5V 1F 28 29 30 11 USER SELECTABLE REFERENCES 0.1V TO VCC 10 24 23 8 9 ANALOG INPUTS 12 22 7 VCC = EXTERNAL OSCILLATOR = INTERNAL OSCILLATOR 35 FO LTC2446 REFG+ REFG- REF01+ - REF01 . .. REF67+ REF67- 34 SDI 38 SCK 4-WIRE SPI INTERFACE CH0 CH1 SDO CH2 . CS CH7 BUSY COM GND .. 37 36 2 1,4,5,6,31,32,33 <tEOC(TEST) CS TEST EOC TEST EOC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 32 SCK SDI SDO DON'T CARE Hi-Z 1 0 EN SGL ODD GLBL A1 A0 OSR3 OSR2 OSR1 BIT 31 BIT 30 BIT 29 BIT 28 BIT 27 BIT 26 BIT 25 BIT 24 BIT 23 BIT 22 BIT 21 EOC "0" SIG OSR0 TWOX BIT 20 BIT 19 DON'T CARE BIT 0 LSB MSB Hi-Z BUSY CONVERSION SLEEP DATA OUTPUT CONVERSION 244676 F08 Figure 8. Internal Serial Clock, Single Cycle Operation 24467fb 18 For more information www.linear.com/LTC2446 LTC2446/LTC2447 APPLICATIONS INFORMATION If CS remains LOW longer than tEOCtest, the first rising edge of SCK will occur and the conversion result is serially shifted out of the SDO pin. The data output cycle begins on this first rising edge of SCK and concludes after the 32nd rising edge. Data is shifted out the SDO pin on each falling edge of SCK. The internally generated serial clock is output to the SCK pin. This signal may be used to shift the conversion result into external circuitry. EOC can be latched on the first rising edge of SCK and the last bit of the conversion result on the 32nd rising edge of SCK. After the 32nd rising edge, SDO goes HIGH (EOC = 1), SCK stays HIGH and a new conversion starts. of SCK, see Figure 9. On the rising edge of CS, the device aborts the data output state and immediately initiates a new conversion. This is useful for systems not requiring all 32 bits of output data, aborting an invalid conversion cycle, or synchronizing the start of a conversion. Thirteen serial input data bits are required in order to properly program the speed/resolution and input channel. If the data output sequence is aborted prior to the 13th rising edge of SCK, the new input data is ignored, and the previously selected speed/resolution and channel are used for the next conversion cycle. If a new channel is being programmed, the rising edge of CS must come after the 14th falling edge of SCK in order to store the data input sequence. Typically, CS remains LOW during the data output state. However, the data output state may be aborted by pulling CS HIGH anytime between the first and 32nd rising edge 4.5V TO 5.5V 1F 28 29 30 USER SELECTABLE REFERENCES 0.1V TO VCC 11 10 24 23 8 9 ANALOG INPUTS 12 22 7 VCC = EXTERNAL OSCILLATOR = INTERNAL OSCILLATOR 35 FO LTC2446 REFG+ REFG- REF01+ - REF01 . .. REF67+ REF67- 34 SDI 38 SCK 4-WIRE SPI INTERFACE CH0 CH1 SDO CH2 . CS CH7 BUSY COM GND .. 37 36 2 1,4,5,6,31,32,33 <tEOC(TEST) <tEOC(TEST) CS 1 5 1 2 3 4 5 TEST EOC 6 SCK SDI DON'T CARE DON'T CARE DON'T CARE BIT 31 BIT 30 BIT 29 BIT 28 BIT 27 BIT 26 BIT 25 Hi-Z SDO EOC "0" SIG MSB Hi-Z BUSY CONVERSION DATA OUTPUT SLEEP CONVERSION DATA OUTPUT CONVERSION SLEEP 24467 F09 Figure 9. Internal Serial Clock, Reduced Data Output Length 24467fb For more information www.linear.com/LTC2446 19 LTC2446/LTC2447 APPLICATIONS INFORMATION Internal Serial Clock, 3-Wire I/O, Continuous Conversion device has entered the low power sleep state. The part remains in the sleep state a minimum amount of time (500ns) then immediately begins outputting data. The data output cycle begins on the first rising edge of SCK and ends after the 32nd rising edge. Data is shifted out the SDO pin on each falling edge of SCK. The internally generated serial clock is output to the SCK pin. This signal may be used to shift the conversion result into external circuitry. EOC can be latched on the first rising edge of SCK and the last bit of the conversion result can be latched on the 32nd rising edge of SCK. After the 32nd rising edge, SDO goes HIGH (EOC = 1) indicating a new conversion is in progress. SCK remains HIGH during the conversion. This timing mode uses a 3-wire, all output (SCK and SDO) interface. The conversion result is shifted out of the device by an internally generated serial clock (SCK) signal, see Figure 10. CS may be permanently tied to ground, simplifying the user interface or isolation barrier. The internal serial clock mode is selected by tying EXT HIGH. During the conversion, the SCK and the serial data output pin (SDO) are HIGH (EOC = 1) and BUSY = 1. Once the conversion is complete, SCK, BUSY and SDO go LOW (EOC = 0) indicating the conversion has finished and the 4.5V TO 5.5V 1F 28 VCC LTC2446 29 REFG+ 30 USER SELECTABLE REFERENCES 0.1V TO VCC REFG- 11 REF01+ 10 - REF01 . .. 24 REF67+ 23 34 SDI REF67- 8 38 SCK 3-WIRE SPI INTERFACE CH0 9 ANALOG INPUTS = EXTERNAL OSCILLATOR = INTERNAL OSCILLATOR 35 FO 12 CH1 SDO CH2 . CS CH7 BUSY COM GND .. 22 7 37 36 2 1,4,5,6,31,32,33 CS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 32 1 0 EN SGL ODD GLBL A1 A0 OSR3 OSR2 OSR1 OSR0 TWOX DON'T CARE BIT 20 BIT 19 BIT 0 SCK SDI DON'T CARE BIT 31 BIT 30 BIT 29 BIT 28 BIT 27 BIT 26 BIT 25 BIT 24 BIT 23 BIT 22 BIT 21 EOC SDO "0" SIG LSB MSB BUSY CONVERSION DATA OUTPUT SLEEP CONVERSION 24467 F10 Figure 10. Internal Serial Clock, Continuous Operation 24467fb 20 For more information www.linear.com/LTC2446 LTC2446/LTC2447 APPLICATIONS INFORMATION Normal Mode Rejection and Anti-aliasing Table 6. OSR vs Notch Frequency (fN) (with Internal Oscillator) One of the advantages delta-sigma ADCs offer over conventional ADCs is on-chip digital filtering. Combined with a large oversampling ratio, the LTC2446/LTC2447 significantly simplify anti-aliasing filter requirements. The LTC2446/LTC2447's speed/resolution is determined by the over sample ratio (OSR) of the on-chip digital filter. The OSR ranges from 64 for 3.5kHz output rate to 32,768 for 6.9Hz (in 1x mode) output rate. The value of OSR and the sample rate fS determine the filter characteristics of the device. The first NULL of the digital filter is at fN and multiples of fN where fN = fS/OSR, see Figure 11 and Table 6. The rejection at the frequency fN 14% is better than 80dB, see Figure 12. SINC4 ENVELOPE -20 -40 -60 -80 -100 -120 -140 Figure 11. LTC2446/LTC2447 Normal Mode Rejection (Internal Oscillator) NORMAL MODE REJECTION (dB) -80 -90 -100 28.16kHz 14.08kHz 256 7.04kHz 512 3.52kHz 1024 1.76kHz 2048 880Hz 4096 440Hz 8192 220Hz 16384 110Hz 32768* 55Hz 0 -20 -40 -60 1.8MHz -80 -100 REJECTION > 120dB -120 -140 -110 -120 2000000 1000000 0 DIFFERENTIAL INPUT SIGNAL FREQUENCY (Hz) 24467 F13 Figure 13. LTC2446/LTC2447 Normal Mode Rejection (Internal Oscillator) -130 -140 64 128 If FO is grounded, fS is set by the on-chip oscillator at 1.8MHz (over supply and temperature variations). At an OSR of 32,768, the first NULL is at fN = 55Hz and the no latency output rate is fN/8 = 6.9Hz. At the maximum OSR, the noise performance of the device is 280nVRMS (LTC2446) and 200nVRMS (LTC2447) with better than 80dB rejection of 50Hz 2% and 60Hz 2%. Since the OSR is large (32,768) the wide band rejection is extremely large and the anti-aliasing requirements are simple. The first multiple of fS occurs at 55Hz * 32,768 = 1.8MHz, see Figure 13. 60 120 240 0 180 DIFFERENTIAL INPUT SIGNAL FREQUENCY (Hz) 24467 F11 NOTCH (fN) *Simultaneous 50/60Hz rejection NORMAL MODE REJECTION (dB) NORMAL MODE REJECTION (dB) 0 OSR 47 49 51 53 55 57 59 61 63 DIFFERENTIAL INPUT SIGNAL FREQUENCY (Hz) 24467 F12 Figure 12. LTC2446/LTC2447 Normal Mode Rejection (Internal Oscillator) For more information www.linear.com/LTC2446 24467fb 21 LTC2446/LTC2447 APPLICATIONS INFORMATION The first NULL becomes fN = 7.04kHz with an OSR of 256 (an output rate of 880Hz) and FO grounded. While the NULL has shifted, the sample rate remains constant. As a result of constant modulator sampling rate, the linearity, offset and full-scale performance remain unchanged as does the first multiple of fS. The sample rate fS and NULL fN, may also be adjusted by driving the FO pin with an external oscillator. The sample rate is fS = fEOSC/5, where fEOSC is the frequency of the clock applied to FO. Combining a large OSR with a reduced sample rate leads to notch frequencies fN near DC while maintaining simple anti-aliasing requirements. A 100kHz clock applied to FO results in a NULL at 0.6Hz plus all harmonics up to 20kHz, see Figure 14. This is useful in applications requiring digitalization of the DC component of a noisy input signal and eliminates the need of placing a 0.6Hz filter in front of the ADC. NORMAL MODE REJECTION (dB) 1F 28 29 30 USER SELECTABLE REFERENCES 0.1V TO VCC 11 10 24 23 8 9 ANALOG INPUTS 12 22 7 VCC 35 FO OUT LTC2446 LTC1799 REFG+ REF01+ REF67- 0.1F 38 SCK CH1 SDO CH2 . CS CH7 BUSY COM GND SET 34 SDI CH0 .. DIV NC - REF01 . .. RSET GND REFG- REF67+ V+ 37 4-WIRE SPI INTERFACE 36 2 1,4,5,6,31,32,33 24467 F15 Figure 15. Simple External Clock Source The normal mode rejection characteristic shown in Figure 14 is achieved by applying the output of the LTC1799 (with RSET = 100k) to the FO pin on the LTC2446/LTC2447 with SDI tied HIGH (OSR = 32768). 0 -20 -40 -60 Multiple Ratiometric and Absolute Measurements -80 -100 -120 -140 4.5V TO 5.5V 2 4 6 10 8 0 DIFFERENTIAL INPUT SIGNAL FREQUENCY (Hz) 24467 F14 Figure 14. LTC2446/LTC2447 Normal Mode Rejection (External Oscillator at 90kHz) An external oscillator operating from 100kHz to 12MHz can be implemented using the LTC1799 (resistor set SOT23 oscillator), see Figure 15. By floating pin 4 (DIV) of the LTC1799, the output oscillator frequency is: 10k fOSC =10MHz * 10 *RSET The LTC2446/LTC2447 combine a high precision, high speed delta-sigma converter with a versatile front-end multiplexer. The unique no latency architecture allows seamless changes in both input channel and reference while the absolute accuracy ensures excellent matching between both analog input channels and reference channels. Any set of inputs (differential or single-ended) can perform a conversion with one of two references. For Bridges, RTDs and other ratiometric devices, each set of channels can perform a conversion with respect to a unique reference voltage. For Thermocouples, voltage sense, current sense and other absolute sensors, each set of channels can perform a conversion with respect to a single global reference voltage (see Figure 16). This allows users to measure both multiple absolute and multiple ratio metric sensors with the same device in such applications as flow, gas chromatography, multiple RTDs or bridges, or universal data acquisition. 24467fb 22 For more information www.linear.com/LTC2446 LTC2446/LTC2447 APPLICATIONS INFORMATION VCC VREF 10F LTC2446 VREFG+ VREFO1+ RTD VREFO1- CH0 CH1 REF+ VREF23+ RATIOMETRIC RTD VREF23- CH2 CH3 IN+ IN- CS + - SDI VARIABLE SPEED RESOLUTION 24-BIT ADC SDO SCK CH4 VREF45+ BRIDGE CH5 REF- VREF45- ABSOLUTE vs VREFG CH6 CH7 COM VREFG 24467 F16 Figure 16. Versatile 4-Way Multiplexer Measures Multiple Ratiometric/Absolute Sensors Average Input Current IREF+ The LTC2446 switches the input and reference to a 2pF capacitor at a frequency of 1.8MHz. A simplified equivalent circuit is shown in Figure 17. The sample capacitor for the LTC2447 is 4pF, and its average input current is externally buffered from the input source. The average input and reference currents can be expressed in terms of the equivalent input resistance of the sample capacitor, where: Req = 1/(fSW * CEQ). When using the internal oscillator, fSW is 1.8MHz and the equivalent resistance is approximately 110k. VCC RSW (TYP) 500 ILEAK VREF+ ILEAK VCC IIN+ ILEAK VIN+ IIN - ILEAK RSW (TYP) 500 CEQ 5pF (TYP) (CEQ = 2pF SAMPLE CAP + PARASITICS) MUX VCC RSW (TYP) 500 ILEAK VIN - ILEAK MUX VCC IREF - ILEAK VREF - ILEAK RSW (TYP) 500 24467 F17 SWITCHING FREQUENCY fSW = 1.8MHz INTERNAL OSCILLATOR fSW = fEOSC/5 EXTERNAL OSCILLATOR Figure 17. LTC2446 Input Structure For more information www.linear.com/LTC2446 24467fb 23 LTC2446/LTC2447 APPLICATIONS INFORMATION Input Bandwidth and Frequency Rejection Effective Noise Bandwidth The combined effect of the internal SINC4 digital filter and the digital and analog auto-calibration circuits determines the LTC2446/LTC2447 input bandwidth and rejection characteristics. The digital filter's response can be adjusted by setting the oversample ratio (OSR) through the SPI interface or by supplying an external conversion clock to the FO pin. The LTC2446/LTC2447 has extremely good input noise rejection from the first notch frequency all the way out to the modulator sample rate (typically 1.8MHz). Effective noise bandwidth is a measure of how the ADC will reject wideband input noise up to the modulator sample rate. The example on the following page shows how the noise rejection of the LTC2446/LTC2447 reduces the effective noise of an amplifier driving its input. Table 7 lists the properties of the LTC2446/LTC2447 with various combinations of oversample ratio and clock frequency. Understanding these properties is the key to fine tuning the characteristics of the LTC2446/LTC2447 to the application. Example: If an amplifier (e.g. LT1219) driving the input of an LTC2446/LTC2447 has wideband noise of 33nV/Hz, band-limited to 1.8MHz, the total noise entering the ADC input is: 33nV/Hz * 1.8MHz = 44.3V. Maximum Conversion Rate The maximum conversion rate is the fastest possible rate at which conversions can be performed. First Notch Frequency This is the first notch in the SINC4 portion of the digital filter and depends on the FO clock frequency and the oversample ratio. Rejection at this frequency and its multiples (up to the modulator sample rate of 1.8MHz) exceeds 120dB. This is 8 times the maximum conversion rate. When the ADC digitizes the input, its digital filter rejects the wideband noise from the input signal. The noise reduction depends on the oversample ratio which defines the effective bandwidth of the digital filter. At an oversample of 256, the noise bandwidth of the ADC is 787Hz which reduces the total amplifier noise to: 33nV/Hz * 787Hz = 0.93V. Table 7. Performance vs Oversample Ratio Maximum Conversion Rate First Notch Frequency Effective Noise BW -3dB Point (sps) (Hz) (Hz) (Hz) OverENOB sample *RMS *RMS External fO External fO (VREF = 5V) Ratio Noise Internal (1x Mode) (2x Mode) Internal External fO Internal External fO Internal External fO Noise (OSR) LTC2446 LTC2447 LTC2446 LTC2447 Clock (fO/x) (fO/x) Clock (fO/x) 9MHz Clock (fO/x) Clock (fO/x) 64 23V 23V 17 17 2816.35 fO/2738 fO/1458 28125 fO/320 3148 fO/2860 1696 fO/5310 128 4.5V 3.5V 20.1 20 1455.49 fO/5298 fO/2738 14062.5 fO/640 1574 fO/5720 848 fO/10600 256 2.8V 2V 20.8 21.3 740.18 fO/10418 fO/5298 7031.3 fO/1280 787 fO/11440 424 fO/21200 512 2V 1.4V 21.3 21.8 373.28 fO/20658 fO/10418 3515.6 fO/2560 394 fO/22840 212 fO/42500 1024 1.4V 1V 21.8 22.4 187.45 fO/41138 fO/20658 1757.8 fO/5120 197 fO/45690 106 fO/84900 2048 1.1V 750nV 22.1 22.9 93.93 fO/82098 fO/41138 878.9 fO/10200 98.4 fO/91460 53 fO/170000 4096 720nV 510nV 22.7 23.4 47.01 fO/164018 fO/82098 439.5 fO/20500 49.2 fO/183000 26.5 fO/340000 8192 530nV 375nV 23.2 24 23.52 fO/327858 fO/164018 219.7 fO/41000 24.6 fO/366000 13.2 fO/679000 16384 350nV 250nV 23.8 24.4 11.76 fO/655538 fO/327858 109.9 fO/81900 12.4 fO/731000 6.6 fO/1358000 32768 280nV 200nV 24.1 24.6 5.88 fO/1310898 fO/655538 54.9 fO/163800 6.2 fO/1463000 3.3 fO/2717000 *ADC noise increases by approximately 2 when OSR is decreased by a factor of 2 for OSR 32768 to OSR 256. The ADC noise at OSR 128 and OSR 64 include effects from internal modulator quantization noise. 24467fb 24 For more information www.linear.com/LTC2446 LTC2446/LTC2447 APPLICATIONS INFORMATION The total noise is the RMS sum of this noise with the 2V noise of the ADC at OSR = 256. (0.93V)2 + (2V)2 = 2.2V. Increasing the oversample ratio to 32768 reduces the noise bandwidth of the ADC to 6.2Hz which reduces the total amplifier noise to: 33nV/Hz * 6.2Hz = 82nV. The total noise is the RMS sum of this noise with the 200nV noise of the ADC at OSR = 32768. (82nV)2 + (200nV)2 = 216nV. In this way, the digital filter with its variable oversampling ratio can greatly reduce the effects of external noise sources. 10 FIVE DIFFERENTIAL REFERENCE INPUTS Automatic Offset Calibration of External Buffers/Amplifiers The LTC2447 enables an external amplifier to be inserted between the multiplexer output and the ADC input. This enables one external buffer/amplifier circuit to be shared between all nine analog inputs (eight single-ended or four differential). The LTC2447 performs an internal offset calibration every conversion cycle in order to remove the offset and drift of the ADC. This calibration is performed through a combination of front end switching and digital processing. Since the external amplifier is placed between the multiplexer and the ADC, it is inside the correction loop. This results in automatic offset correction and offset drift removal of the external amplifier. MUX LTC2447 ADCINP 2 OFFSETS AND 1/f NOISE OF EXTERNAL SIGNAL CONDITIONING CIRCUITS ARE AUTOMATICALLY CANCELLED 3 - 1/2 LT1368 + ADCINN MUX MUXOUTP CH0-CH6/ COM MUXOUTN 9 SDI REF+ HIGH SPEED ADC REF- SCK SDO CS 1 0.1F* *LT1368 REQUIRES 0.1F OUTPUT COMPENSATION CAPACITOR (EXTERNAL AMPLIFIERS) 6 5 - 5V 8 1/2 LT1368 + 4 7 0.1F* 0V 24467 F18 Figure 18. External Buffers Provide High Impedance Inputs and Amplifier Offsets are Cancelled 24467fb For more information www.linear.com/LTC2446 25 LTC2446/LTC2447 APPLICATIONS INFORMATION The LT1368 is an excellent amplifier for this function. It has rail-to-rail inputs and outputs, and it operates on a single 5V supply. Its open-loop gain is 1M and its input bias current is 10nA. It also requires at least a 0.1F load capacitor for compensation. It is this feature that sets it apart from other amplifiers--the load capacitor attenuates sampling glitches from the LTC2447 ADCIN terminal, allowing it to achieve full performance of the ADC with high impedance at the multiplexer inputs. Another benefit of the LT1368 is that it can be powered from supplies equal to or greater than that of the ADC. This can allow the inputs to span the entire absolute maximum of GND - 0.3V to VCC + 0.3V. Using a positive supply of 7.5V to 10V and a negative supply of -2.5 to -5V gives the amplifier plenty of headroom over the LTC2447 input range. Interfacing Sensors to the LTC2447 Figure 19 shows a few of the ways that the multiple reference inputs of the LTC2447 greatly simplify sensor interfacing. Each of the four references is fully differential and has a differential range of 100mV to 5V. This opens up many possibilities for sensing voltages and currents, eliminating much of the analog signal conditioning circuitry required for interfacing to conventional ADCs. Figure 19a is a standard 350, voltage excited strain gauge with sense wires for the excitation voltage. REF01+ and REF01- sense the excitation voltage at the gauge, compensating for voltage drop along the high current excitation supply wires. This can be a significant error, as the excitation current is 14mA when excited with 5V. Reference loading capacitors at the ADC are necessary to average the reference current during sampling. Both ADC inputs are always close to mid-reference, and hence close to mid-supply when using 5V excitation. Figure 19b is a novel way to interface the LTC2447 to a bridge that is specified for constant current excitation. The Fujikura FPM-120PG is a 120psig pressure sensor that is not trimmed for absolute accuracy, but is temperature compensated for low drift when excited by a constant current source. The LTC2447's fully differential reference allows sensing the excitation current with a resistor in series with the bridge excitation. Changes in ambient temperature and supply voltage will cause the current to vary, but the LTC2447 compensates by using the current sense voltage as its reference. The input common mode will be slightly higher than mid-reference, but still far enough away from the positive supply to eliminate concerns about the buffer amplifier's headroom. Figure 19c is an Omega 44018 linear output thermistor. Two fixed resistors linearize the output from the thermistors. The recommended 5700 series resistor is broken up into two 2850 resistors to give a differential output centered around mid-reference. This ensures that the buffer amplifiers have enough headroom at the negative supply. Note that the excitation is 3V, the maximum recommended by the manufacturer to prevent self-heating errors. The LTC2447 senses this reference voltage. Figure 19d shows a standard 100 platinum RTD. This circuit shows how to use the LTC2447 to make a direct resistance measurement, where the output code is the RTD resistance divided by the reference resistance. A 500 sense resistor allows measurement of resistance up to 250. (A standard = 0.00385 RTD has a resistance of 247.09 at 400C.) The LTC2446 multiplexes rail-to-rail inputs directly to the ADC modulator and is suitable for low impedance resistive sources such as 100 RTDs and 350 strain gauges that are located close to the ADC. In applications where the source resistance is high or the source is located more 24467fb 26 For more information www.linear.com/LTC2446 LTC2446/LTC2447 APPLICATIONS INFORMATION than 5cm to 10cm from the ADC, the LTC2447 (with an LT1368 buffer) is appropriate. The LTC2447 automatically removes offset, drift and 1/f noise of the LT(R)1368. One consideration for single supply applications is that both ADC inputs should always be at least 100mV from the LT1368's supply rails. All of the applications shown in Figure 19 are designed to keep both analog inputs far enough away from ground and VCC so that the LT1368 can operate on the same 5V supply as the LTC2447. Although the LT1368 has rail-to-rail inputs and outputs, these amplifiers still need some degree of headroom to work at the resolution level of the LTC2447. For input signals running rail-to-rail, the supply voltage of the LT1368 can be increased in order to provide the extra headroom. The LTC2446/LTC2447 reference have no such limitations --they are truly rail-to-rail, and will even operate up to 300mV outside the supply rails. Reference terminals may be connected directly to the ground plane or to a reference voltage that is decoupled to the ground plane with a 1F or larger capacitor without any degradation of performance provided the connection is less than 5cm from the LTC2446/LTC2447. If the reference terminals are sensing a point more than 5cm to 10cm away from the ADC, the reference pins should be decoupled to the ground plane with 1F capacitors. The reference terminals can also sense a resistive source with a resistance up to 500 located close to the LTC2446/ LTC2447, however parasitic capacitance must be kept to a minimum. If the sense point is more than 5cm from the ADC, then it should be buffered. The LT1368 is also an outstanding reference buffer. While offsets are not cancelled as in the ADC input circuit, the 200mV offset and 2mV/C drift will not degrade the performance of most sensors. The LT1369 is a quad version of the LT1368, and can serve as the input buffer for an LTC2447 and two reference buffers. 24467fb For more information www.linear.com/LTC2446 27 LTC2446/LTC2447 PACKAGE DESCRIPTION Please refer to http://www.linear.com/product/LTC2446#packaging for the most recent package drawings. UHF Package 38-Lead Plastic QFN (5mm x 7mm) (Reference LTC DWG # 05-08-1701 Rev C) 0.70 0.05 5.50 0.05 5.15 0.05 4.10 0.05 3.00 REF 3.15 0.05 PACKAGE OUTLINE 0.25 0.05 0.50 BSC 5.5 REF 6.10 0.05 7.50 0.05 RECOMMENDED SOLDER PAD LAYOUT APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 0.75 0.05 5.00 0.10 PIN 1 NOTCH R = 0.30 TYP OR 0.35 x 45 CHAMFER 3.00 REF 37 0.00 - 0.05 38 0.40 0.10 PIN 1 TOP MARK (SEE NOTE 6) 1 2 5.15 0.10 5.50 REF 7.00 0.10 3.15 0.10 (UH) QFN REF C 1107 0.200 REF 0.25 0.05 R = 0.125 TYP 0.50 BSC R = 0.10 TYP BOTTOM VIEW--EXPOSED PAD NOTE: 1. DRAWING CONFORMS TO JEDEC PACKAGE OUTLINE M0-220 VARIATION WHKD 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 24467fb 28 For more information www.linear.com/LTC2446 LTC2446/LTC2447 REVISION HISTORY (Revision history begins at Rev B) REV DATE DESCRIPTION B 01/17 Updated Max value for fEOSC. PAGE NUMBER 4 Updated formula for tCONV. 4 Updated Note 13. 5 Inserted Figure 4. Input Range. 13 Revised Table 7. Performance vs Oversample Ratio. 24 24467fb Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. For more information www.linear.com/LTC2446 29 LTC2446/LTC2447 TYPICAL APPLICATION 5V 5V VREF01+ 1F 350 LOAD CELL - + FUJIKURA FPM-120PG (4k TO 6k IMPEDANCE) - + CH3 FULL-SCALE OUTPUT = 60mV TO 140mV CH0 CH2 FULL-SCALE OUTPUT = 10mV VREF23+ CH1 5V SELECT FOR V > 2 * 140mV AT MAXIMUM BRIDGE RESISTANCE VREF23- 375 VREF01- 1F GND GND (19a) Full-Bridge, Voltage Sense (19b) Full-Bridge, Current Sense 5V VREF45+ LT1790-3 1F 2850 RILIM CH5 GND CH7 12.4k OMEGA 44018 LINEAR THERMISTOR COMPOSITE T2 SENSOR 100 AT 0C 247.09 AT 400C 100 RTD T1 CH6 VREF67+ CH4 THERMISTOR 2850 500 VREF67- VREF45- 24467 F19 GND GND (19c) Half-Bridge, Voltage Sense (19d) Half-Bridge, Current Sense Figure 19. Muxed Inputs/References Enable Multiple Ratiometric Measurements with the Same Device RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT1236A-5 Precision Bandgap Reference, 5V 0.05% Max, 5ppm/C Drift LT1461 Micropower Series Reference, 2.5V 0.04% Max, 3ppm/C Max Drift LTC1799 Resistor Set SOT-23 Oscillator Single Resistor Frequency Set LTC2053 Rail-to-Rail Instrumentation Amplifier 10V Offset with 50nV/C Drift, 2.5VP-P Noise 0.01Hz to 10Hz LTC2412 2-Channel, Differential Input, 24-Bit, No Latency ADC 0.16ppm Noise, 2ppm INL, 200A LTC2415 1-Channel, Differential Input, 24-Bit, No Latency ADC 0.23ppm Noise, 2ppm INL, 2x Speed Mode LTC2414/LTC2418 4-/8-Channel, Differential Input, 24-Bit, No Latency ADC 0.2ppm Noise, 2ppm INL, 200A LTC2430/LTC2431 1-Channel, Differential Input, 20-Bit, No Latency ADC 0.56ppm Noise, 3ppm INL, 200A LTC2436-1 2-Channel, Differential Input, 16-Bit, No Latency ADC 800nVRMS Noise, 0.12LBS INL, 0.006LBS Offset, 200A LTC2440 1-Channel, Differential Input, High Speed/Low Noise, 24-Bit, 2VRMS Noise at 880Hz, 200nVRMS Noise at 6.9Hz, 0.0005% INL, Up No Latency ADC to 3.5kHz Output Rate LTC2444/LTC2445/ LTC2448/LTC2449 8-/16-Channel, Differential Input, High Speed/Low Noise, 24-Bit, No Latency ADC 2VRMS Noise at 1.76kHz, 200nVRMS Noise at 13.8Hz, 0.0005% INL, Up to 8kHz Output Rate 24467fb 30 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 For more information www.linear.com/LTC2446 (408) 432-1900 FAX: (408) 434-0507 www.linear.com/LTC2446 LT 0117 REV B * PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 2004