AT24C512C I2C-Compatible (2-wire) Serial EEPROM 512-Kbit (65,536 x 8) DATASHEET Features Low-voltage and Standard-voltage Operation Internally Organized as 65,536 x 8 (512K) I2C-Compatible (2-Wire) Serial Interface Schmitt Triggers, Filtered Inputs for Noise Suppression Bidirectional Data Transfer Protocol 400kHz (1.7V) and 1MHz (2.5V, 5.5V) Compatibility Write Protect Pin for Hardware Data Protection 128-byte Page Write Mode Partial Page Writes Allowed Random and Sequential Read Modes Self-timed Write Cycle (5ms Max) High Reliability Endurance: 1,000,000 Write Cycles Data Retention: 40 Years Green Package Options (Pb/Halide-free/RoHS Compliant) VCC = 1.7V to 3.6V VCC = 2.5V to 5.5V 8-lead JEDEC SOIC, 8-lead EIAJ SOIC, 8-lead TSSOP, 8-pad UDFN, 8-ball WLCSP, and 8-ball VFBGA Packages Die sale Options: Wafer Form and Tape and Reel Available Description The Atmel(R) AT24C512C provides 524,288 bits of Serial Electrically Erasable and Programmable Read-Only Memory (EEPROM) organized as 65,536 words of 8 bits each. The cascadable feature of the device allows up to eight devices to share a common 2-wire bus. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential. The devices are available in space-saving 8-lead JEDEC SOIC, 8-lead EIAJ SOIC, 8-lead TSSOP, 8-pad UDFN, 8-ball WLCSP, and 8-ball VFBGA packages. In addition, the entire family is available in 1.7V to 3.6V and 2.5V to 5.5V versions. Atmel-8720G-SEEPROM-AT24C512C-Datasheet_092015 1. Pin Configurations and Pinouts Figure 1. Pin Configurations Pin Name Function A0, A1, A2 Address Inputs GND Ground SDA Serial Data SCL Serial Clock Input WP Write Protect VCC Power Supply 8-lead SOIC 8-lead TSSOP A0 1 8 VCC A1 2 7 WP A2 3 6 SCL GND 4 5 SDA A0 A1 A2 GND 1 2 3 4 Top View 8-pad UDFN A0 A1 A2 GND VCC WP SCL SDA 8 7 6 5 Top View 8-ball WLSCP SDA VCC SCL A2 WP A1 GND A0 Top View VCC WP SCL SDA Top View A0 1 8 VCC A1 2 7 WP A2 3 6 SCL GND 4 5 SDA Top View Drawings are not to scale. Absolute Maximum Ratings Operating Temperature . . . . . . . . . . .-55C to +125C Storage Temperature . . . . . . . . . . . . .-65C to +150C Voltage on any pin with respect to ground . . . . . . . . . . . . . -1.0V to +7.0V Maximum Operating Voltage . . . . . . . . . . . . . . . 6.25V DC Output Current . . . . . . . . . . . . . . . . . . . . . . .5.0mA 2 8 7 6 5 8-ball VFBGA Note: 2. 1 2 3 4 AT24C512C [DATASHEET] Atmel-8720G-SEEPROM-AT24C512C-Datasheet_092015 Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 3. Block Diagram Figure 3-1. Block Diagram VCC GND WP Start Stop Logic Serial Control Logic LOAD Device Address Comparator A2 A1 A0 R/W EN H.V. Pump/Timing COMP LOAD Data Recovery INC Data Word Addr/counter Y DEC X DEC SCL SDA EEPROM Serial MUX DOUT/ACK Logic DIN DOUT 4. Pin Descriptions Serial Clock (SCL) -- The SCL input is used to positive-edge clock data into each EEPROM device and negativeedge clock data out of each device. Serial Data (SDA) -- The SDA pin is bidirectional for serial data transfer. This pin is open-drain driven, and may be wire-ORed with any number of other open-drain or open-collector devices. Device Addresses (A2, A1, A0) -- The A2, A1, and A0 pins are device address inputs that are hardwired or left not connected for compatibility with other Atmel AT24Cxx devices. When the pins are hardwired, as many as eight 512K devices may be addressed on a single bus system (see Section 7. "Device Addressing" on page 9 for more details). If these pins are left floating, the A2, A1, and A0 pins will be internally pulled down to GND. However, due to capacitive coupling that may appear during customer applications, Atmel recommends always connecting the address pins to a known state. When using a pull-up resistor, Atmel recommends using 10k or less. Write Protect (WP) -- The Write Protect input, when connected to GND, allows normal write operations. When WP pin is connected directly to VCC, all write operations to the memory are inhibited. If the pin is left floating, the WP pin will be internally pulled down to GND; however, due to capacitive coupling that may appear during customer applications, Atmel recommends always connecting the WP pin to a known state. When using a pull-up resistor, Atmel recommends using 10k or less. Table 4-1. Write Protect WP Pin Status Part of the Array Protected At VCC Full Array At GND Normal Read/Write Operations AT24C512C [DATASHEET] Atmel-8720G-SEEPROM-AT24C512C-Datasheet_092015 3 5. Memory Organization AT24C512C, 512-Kbit Serial EEPROM: The 512K is internally organized as 512 pages of 128 bytes each. Random word addressing requires a 16-bit data word address. 5.1 Pin Capacitance Table 5-1. Pin Capacitance(1) Applicable over recommended operating range from TA = 25C, f = 1.0MHz, VCC = 5.5V. Symbol Test Condition CI/O CIN Note: 5.2 1. Max Units Conditions Input/Output Capacitance (SDA) 8 pF VI/O = 0V Input Capacitance (A0, A1, A2, SCL) 6 pF VIN = 0V This parameter is characterized and is not 100% tested. DC Characteristics Table 5-2. DC Characteristics Applicable over recommended operating range from: TAI = -40C to +85C, VCC = 1.7V to 3.6V or 2.5V to 5.5V (unless otherwise noted). Symbol Parameter VCC1 Supply Voltage VCC2 Supply Voltage ICC1 Supply Current VCC = 3.6V ICC2 Supply Current VCC = 5.0V ISB1 Standby Current ISB2 Standby Current ILI Input Leakage Current VIN = VCC or VSS ILO Output Leakage Current VOUT = VCC or VSS VIL Input Low Level(1) VIH Input High Level(1) VOL1 Output Low Level VCC = 1.7V VOL2 Output Low Level VCC = 3.0V Note: 4 1. Test Condition VCC = 1.7V VCC = 3.6V VCC = 2.5V VCC = 5.5V Max Units 1.7 3.6 V 2.5 5.5 V Read at 400kHz 1.0 mA Write at 400kHz 3.0 mA Read at 400kHz 2.0 mA Write at 400kHz 3.0 mA Atmel-8720G-SEEPROM-AT24C512C-Datasheet_092015 Typ 1.0 A 3.0 A 2.0 A 6.0 A 0.10 3.0 A 0.05 3.0 A -0.6 VCC x 0.3 V VCC x 0.7 VCC + 0.5 V IOL = 0.15mA 0.2 V IOL = 2.1mA 0.4 V VIN = VCC or VSS VIN = VCC or VSS VIL min and VIH max are reference only, and are not tested. AT24C512C [DATASHEET] Min 5.3 AC Characteristics Table 5-3. AC Characteristics Applicable over recommended operating range from TAI = -40C to +85C, VCC = 1.7V to 3.6V or 2.5V to 5.5V (where applicable), CL = 100pF (unless otherwise noted). Test conditions are listed in Note 2. 1.7V Min 2.5V, 5.0V Symbol Parameter Max Min fSCL Clock Frequency, SCL tLOW Clock Pulse Width Low 1.3 0.4 s tHIGH Clock Pulse Width High 0.6 0.4 s tI Noise Suppression Time(1) tAA Clock Low to Data Out Valid 0.05 tBUF Time the bus must be free before a new transmission can start(1) 1.3 0.5 s tHD.STA Start Hold Time 0.6 0.25 s tSU.STA Start Set-up Time 0.6 0.25 s tHD.DAT Data In Hold Time 0 0 s tSU.DAT Data In Set-up Time 100 100 ns tR Inputs Rise Time(1) 400 100 (1) 0.9 0.05 Max Units 1000 kHz 50 ns 0.55 s 0.3 0.3 s 300 100 ns tF Inputs Fall Time tSU.STO Stop Set-up Time 0.6 0.25 s tDH Data Out Hold Time 50 50 ns tWR Write Cycle Time (1) Endurance Notes: 1. 2. 25C, Page Mode, 3.3V 5 5 1,000,000 ms Write Cycles This parameter is ensured by characterization only. AC measurement conditions: RL (connects to VCC): 1.3k (2.5V, 5V), 10k (1.7V) Input pulse voltages: 0.3VCC to 0.7VCC Input rise and fall times: 50ns Input and output timing reference voltages: 0.5VCC AT24C512C [DATASHEET] Atmel-8720G-SEEPROM-AT24C512C-Datasheet_092015 5 6. Device Operation Clock and Data Transitions: The SDA pin is normally pulled high with an external device. Data on the SDA pin may change only during SCL low time periods. Data changes during SCL high periods will indicate a Start or Stop condition as defined below. Figure 6-1. Data Validity SDA SCL Data Stable Data Stable Data Change Start Condition: A high-to-low transition of SDA with SCL high is a Start condition, which must precede any other command. Stop Condition: A low-to-high transition of SDA with SCL high is a Stop condition. After a read sequence, the stop command will place the EEPROM in a standby power mode. Figure 6-2. Start and Stop Definition SDA SCL Start 6 AT24C512C [DATASHEET] Atmel-8720G-SEEPROM-AT24C512C-Datasheet_092015 Stop Acknowledge: All addresses and data words are serially transmitted to and from the EEPROM in 8-bit words. The EEPROM sends a zero during the ninth clock cycle to acknowledge that it has received each word. Figure 6-3. Output Acknowledge 1 SCL 8 9 Data In Data Out Start Acknowledge Standby Mode: The AT24C512C features a low-power standby mode, which is enabled: Upon power-up and After the receipt of the Stop condition and the completion of any internal operations. Software Reset: After an interruption in protocol, power loss, or system reset, any 2-wire part can be protocol reset by following these steps: 1. Create a Start condition (if possible). 2. 3. Clock nine cycles. Create another Start condition followed by a Stop condition, as shown in Figure 6-4 below. The device should be ready for the next communication after above steps have been completed. In the event that the device is still non-responsive or remains active on the SDA bus, a power cycle must be used to reset the device. Figure 6-4. Software Reset Dummy Clock Cycles SCL 1 Start Condition 2 3 8 9 Start Condition Stop Condition SDA AT24C512C [DATASHEET] Atmel-8720G-SEEPROM-AT24C512C-Datasheet_092015 7 Figure 6-5. Bus Timing SCL: Serial Clock, SDA: Serial Data I/O tHIGH tF tR tLOW SCL tSU.STA tLOW tHD.STA tHD.DAT tSU.DAT tSU.STO SDA IN tAA tDH tBUF SDA OUT Figure 6-6. Write Cycle Timing SCL: Serial Clock, SDA: Serial Data I/O SCL SDA 8th Bit ACK WORDN (1) tWR Stop Condition Note: 8 1. Start Condition The write cycle time, tWR, is the time from a valid Stop condition of a write sequence to the end of the internal clear/write cycle. AT24C512C [DATASHEET] Atmel-8720G-SEEPROM-AT24C512C-Datasheet_092015 7. Device Addressing The 512K EEPROM requires an 8-bit device address word following a Start condition to enable the chip for a read or write operation. The device address word consists of a mandatory `1010' sequence for the first four most-significant bits (see Figure 7-1 below). This is common to all 2-wire EEPROM devices. The 512K uses the three device address bits, A2, A1, and A0, to allow as many as eight devices on the same bus. These bits must compare to their corresponding hardwired input pins. The A2, A1, and A0 pins use an internal proprietary circuit that biases them to a logic low condition if the pins are allowed to float. The eighth bit of the device address is the read/write operation select bit. A read operation is initiated if this bit is high, and a write operation is initiated if this bit is low. Upon a compare of the device address, the EEPROM will output a zero. If a valid compare is not made, the device will return to a standby state. Figure 7-1. 512K Device Address 1 0 1 0 A2 A1 MSB 8. A0 R/W LSB Write Operations Byte Write: A Byte Write operation requires two 8-bit data word addresses following the device address word and acknowledgment. Upon receipt of this address, the EEPROM will again respond with a zero, and then the part is to receive an 8-bit data word. Following receipt of the 8-bit data word, the EEPROM will output a zero. The addressing device, such as a microcontroller, then must terminate the write sequence with a Stop condition. At this time, the EEPROM enters an internally-timed write cycle, tWR, to the nonvolatile memory. All inputs are disabled during this write cycle, and the EEPROM will not respond until the write is complete (see Figure 8-1). Figure 8-1. Byte Write S T A R T Device Address W R I T E First Word Address Second Word Address S T O P Data SDA Line M S B R A / C W K A C K A C K A C K AT24C512C [DATASHEET] Atmel-8720G-SEEPROM-AT24C512C-Datasheet_092015 9 Page Write: The 512-Kbit EEPROM is capable of 128-byte page writes. A Page Write is initiated the same way as a byte write, but the microcontroller does not send a Stop condition after the first data word is clocked in. Instead, after the EEPROM acknowledges receipt of the first data word, the microcontroller can transmit up to 127 more data words. The EEPROM will respond with a zero after each data word received. The microcontroller must terminate the page write sequence with a Stop condition and the internally timed write cycle will begin. The lower seven bits of the data word address are internally incremented following the receipt of each data word. The higher data word address bits are not incremented, retaining the memory page row location. When the word address, internally generated, reaches the page boundary, the following byte is placed at the beginning of the same page. If more than 128 data words are transmitted to the EEPROM, the data word address will roll-over, and the previous data will be overwritten. The address roll over during write is from the last byte of the current page to the first byte of the same page. Figure 8-2. Page Write S T A R T Device Address W R I T E First Word Address (n) Second Word Address (n) Data (n) S T O P Data (n + x) SDA Line M S B R A / C WK A C K A C K A C K A C K Acknowledge Polling: Once the internally-timed write cycle has started and the EEPROM inputs are disabled, Acknowledge Polling can be initiated. This involves sending a Start condition followed by the device address word. The read/write select bit is representative of the operation desired. Only if the internal write cycle has completed will the EEPROM respond with a zero, allowing the read or write sequence to continue. Data Security: AT24C512C has a hardware data protection scheme that allows the user to write protect the entire memory when the WP pin is at VCC. 10 AT24C512C [DATASHEET] Atmel-8720G-SEEPROM-AT24C512C-Datasheet_092015 9. Read Operations Read operations are initiated the same way as write operations with the exception that the read/write select bit in the device address word is set to one. There are three types of read operations: Current Address Read, Random Address Read, and Sequential Read. 9.1 Current Address Read The internal data word address counter maintains the last address accessed during the last read or write operation, incremented by one. This address stays valid between operations as long as the chip power is maintained. The address roll-over during read is from the last byte of the last memory page to the first byte of the first page. Once the device address with the read/write select bit set to one is clocked in and acknowledged by the EEPROM, the current address data word is serially clocked out on the SDA line. The microcontroller does not respond with an zero, but does generate a following Stop condition. Figure 9-1. Current Address Read S T A R T Device Address R E A D S T O P Data SDA Line M S B 9.2 R A / C W K N O A C K Random Read A Random Read requires an initial byte write sequence to load in the data word address. This is known as a "dummy write" operation. Once the device address word and data word address are clocked in and acknowledged by the EEPROM, the microcontroller must generate another Start condition. The microcontroller now initiates a current address read by sending a device address with the read/write select bit high. The EEPROM acknowledges the device address and serially clocks out the data word. The microcontroller does not respond with a zero, but does generate a following Stop condition. Figure 9-2. Random Read S T A R T Device Address W R I T E First Word Address S T A R T Second Word Address Device Address R E A D S T O P Data (n) SDA LINE M S B R A / C W K A C K L A S C B K R A / C WK N O A C K Dummy Write AT24C512C [DATASHEET] Atmel-8720G-SEEPROM-AT24C512C-Datasheet_092015 11 9.3 Sequential Read Sequential Reads are initiated by either a Current Address Read or a Random Address Read. After the microcontroller receives a data word, it responds with an acknowledge. As long as the EEPROM receives an acknowledge, it will continue to increment the data word address and serially clock out sequential data words. When the memory address limit is reached, the data word address will roll-over and the sequential read will continue. The Sequential Read operation is terminated when the microcontroller does not respond with a zero but does generate a following Stop condition. Figure 9-3. Sequential Read S T A R T Device Address W R I T E First Word Address Second Word Address ... SDA LINE M S B R A / C W K L A S C B K A C K Dummy Write S T A R T Device Address R E A D Data (n) Data (n + 1) Data (n + 2) S T O P Data (n + x) ... R A / C K W 12 AT24C512C [DATASHEET] Atmel-8720G-SEEPROM-AT24C512C-Datasheet_092015 A C K A C K A C K N O A C K 10. Ordering Code Detail AT 2 4 C 5 1 2 C - S S H M x x - T Atmel Designator Product Family 24C = Standard I2C-compatible Serial EEPROM Shipping Carrier Option B = Bulk (Tubes) T = Tape and Reel, Standard Quantity Option E = Tape and Reel, Expanded Quantity Option Product Variation xx = Applies to select packages only. See ordering table for variation details. Device Density 512 = 512k Operating Voltage M = 1.7V to 3.6V D = 2.5V to 5.5V Device Revision Package Device Grade or Wafer/Die Thickness H = Green, NiPdAu Lead Finish, Industrial Temperature Range (-40C to +85C) U = Green, Matte Sn Lead Finish, Industrial Temperature Range (-40C to +85C) 11 = 11mil Wafer Thickness Package Option SS = S = X = MA = U1 = C = WWU = JEDEC SOIC EIAJ SOIC TSSOP UDFN WLCSP, 3x5 Grid Array VFBGA Wafer Unsawn AT24C512C [DATASHEET] Atmel-8720G-SEEPROM-AT24C512C-Datasheet_092015 13 11. Part Markings AT24C512C: Package Marking Information 8-lead EIAJ 8-lead SOIC 8-lead TSSOP ATHYWW ###% @ AAAAAAA ATMLHYWW ###% @ AAAAAAAA ATMLHYWW ###% @ AAAAAAAA 8-ball WLCSP 8-pad UDFN 8-ball VFBGA 2.0 x 3.0 mm Body 1.5 x 2.0 mm Body ### H%@ YXX Note 1: ATMEL ###% UYMXX ###U YMXX PIN 1 designates pin 1 Note 2: Package drawings are not to scale Catalog Number Truncation AT24C512C Truncation Code: ### = 2FC Date Codes Y = Year 3: 2013 4: 2014 5: 2015 6: 2016 Voltages 7: 2017 8: 2018 9: 2019 0: 2020 M = Month A: January B: February ... L: December WW = Work Week of Assembly 02: Week 2 04: Week 4 ... 52: Week 52 Country of Assembly Lot Number @ = Country of Assembly AAA...A = Atmel Wafer Lot Number Trace Code % = Minimum Voltage M: 1.7V min D: 2.5V min Grade/Lead Finish Material H: Industrial/NiPdAu U: Industrial/Matte Tin Atmel Truncation XX = Trace Code (Atmel Lot Numbers Correspond to Code) Example: AA, AB.... YZ, ZZ AT: Atmel ATM: Atmel ATML: Atmel 3/25/13 TITLE Package Mark Contact: DL-CSO-Assy_eng@atmel.com 14 AT24C512C [DATASHEET] Atmel-8720G-SEEPROM-AT24C512C-Datasheet_092015 24C512CSM, AT24C512C Package Marking Information DRAWING NO. REV. 24C512CSM E 12. Ordering Information Delivery Information Atmel Ordering Code Lead Finish Package Voltage AT24C512C-SSHM-B Form Quantity Bulk (Tubes) 100 per Tube Tape and Reel 4,000 per Reel Bulk (Tubes) 100 per Tube Tape and Reel 4,000 per Reel Bulk (Tubes) 95 per Tube Tape and Reel 2,000 per Reel Bulk (Tubes) 95 per Tube Tape and Reel 2,000 per Reel Bulk (Tubes) 100 per Tube Tape and Reel 5,000 per Reel Bulk (Tubes) 100 per Tube Operation Range 1.7V to 3.6V AT24C512C-SSHM-T 8S1 AT24C512C-SSHD-B 2.5V to 5.5V AT24C512C-SSHD-T AT24C512C-SHM-B 1.7V to 3.6V AT24C512C-SHM-T 8S2 AT24C512C-SHD-B AT24C512C-SHD-T NiPdAu 2.5V to 5.5V (Lead-free/Halogen-free) AT24C512C-XHM-B 1.7V to 3.6V AT24C512C-XHM-T Industrial Temperature (-40C to 85C) 8X AT24C512C-XHD-B 2.5V to 5.5V AT24C512C-XHD-T 5,000 per Reel AT24C512C-MAHM-T 5,000 per Reel 8MA2 AT24C512C-MAHM-E 15,000 per Reel Tape and Reel AT24C512C-U1UM-T(1) AT24C512C-CUM-T 8U-8 1.7V to 3.6V SnAgCu (Lead-free/Halogen-free) 5,000 per Reel 8U2-1 AT24C512C-CUMHY-T AT24C512C-WWU11M(2) Notes: N/A Wafer Sale Note 2 1. WLCSP Package: CAUTION: Exposure to ultraviolet (UV) light can degrade the data stored in the EEPROM cells. Therefore, customers who use a WLCSP product must ensure that exposure to ultraviolet light does not occur 2. For wafer sales, please contact Atmel sales. Package Type 8S1 8-lead, 0.150" wide, Plastic Gull Wing, Small Outline (JEDEC SOIC) 8S2 8-lead, 0.208" wide, Plastic Gull Wing, Small Outline (EIAJ SOIC) 8X 8-lead, 4.40mm body, Plastic Thin Shrink Small Outline (TSSOP) 8MA2 8-pad, 2.00mm x 3.00mm body, 0.50mm Pitch, Ultra Thin Dual No Lead (UDFN) 8U-8 8-ball, 3 x 5 Grid Array, Wafer Level Chip Scale (WLCSP) 8U2-1 8-ball, 2.35mm x 3.73mm body, 0.75mm pitch, Small Die Ball Grid Array (VFBGA) AT24C512C [DATASHEET] Atmel-8720G-SEEPROM-AT24C512C-Datasheet_092015 15 13. Package Information 13.1 8S1 -- 8-lead JEDEC SOIC C 1 E E1 L N O TOP VIEW END VIEW e b COMMON DIMENSIONS (Unit of Measure = mm) A A1 D SIDE VIEW Notes: This drawing is for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. SYMBOL MIN A 1.35 NOM MAX - 1.75 A1 0.10 - 0.25 b 0.31 - 0.51 C 0.17 - 0.25 D 4.80 - 5.05 E1 3.81 - 3.99 E 5.79 - 6.20 e NOTE 1.27 BSC L 0.40 - 1.27 O 0 - 8 6/22/11 Package Drawing Contact: packagedrawings@atmel.com 16 TITLE 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) AT24C512C [DATASHEET] Atmel-8720G-SEEPROM-AT24C512C-Datasheet_092015 GPC SWB DRAWING NO. REV. 8S1 G 13.2 8S2 -- 8-lead EIAJ SOIC TOP VIEW END VIEW C 1 E E1 L 8 q SIDE VIEW e b A COMMON DIMENSIONS (Unit of Measure = mm) A1 SYMBOL A D Notes: 1. This drawing is for general information only; refer to EIAJ Drawing EDR-7320 for additional information. 2. Mismatch of the upper and lower dies and resin burrs aren't included. 3. Determines the true geometric position. 4. Values b,C apply to plated terminal. The standard thickness of the plating layer shall measure between 0.007 to .021 mm. MIN MAX NOM 1.70 NOTE 2.16 A1 0.05 0.25 b 0.35 0.48 4 C 0.15 0.35 4 D 5.13 5.35 E1 5.18 5.40 E 7.70 8.26 L 0.51 0.85 q 0 e 2 8 1.27 BSC 3 11/10/14 TITLE Package Drawing Contact: packagedrawings@atmel.com 8S2, 8-lead, 0.208" Body, Plastic Small Outline Package (EIAJ) GPC DRAWING NO. REV. STN 8S2 G AT24C512C [DATASHEET] Atmel-8720G-SEEPROM-AT24C512C-Datasheet_092015 17 13.3 8X -- 8-lead TSSOP C 1 Pin 1 indicator this corner E1 E L1 N L Top View End View A b A1 e D SYMBOL Side View Notes: COMMON DIMENSIONS (Unit of Measure = mm) A2 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15mm (0.006in) per side. 3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25mm (0.010in) per side. 4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07mm. 5. Dimension D and E1 to be determined at Datum Plane H. MIN NOM MAX A - - 1.20 A1 0.05 - 0.15 A2 0.80 1.00 1.05 D 2.90 3.00 3.10 2, 5 4.40 4.50 3, 5 0.25 0.30 4 E 6.40 BSC E1 4.30 b 0.19 e L 0.65 BSC 0.45 L1 C NOTE 0.60 0.75 1.00 REF 0.09 - 0.20 2/27/14 TITLE Package Drawing Contact: packagedrawings@atmel.com 18 8X, 8-lead 4.4mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) AT24C512C [DATASHEET] Atmel-8720G-SEEPROM-AT24C512C-Datasheet_092015 GPC TNR DRAWING NO. 8X REV. E 13.4 8MA2 -- 8-pad UDFN E 1 8 Pin 1 ID 2 7 3 6 4 5 D C TOP VIEW A2 SIDE VIEW A A1 E2 b (8x) 8 7 1 D2 6 3 5 4 e (6x) K L (8x) BOTTOM VIEW Notes: COMMON DIMENSIONS (Unit of Measure = mm) 2 Pin#1 ID 1. This drawing is for general information only. Refer to Drawing MO-229, for proper dimensions, tolerances, datums, etc. 2. The Pin #1 ID is a laser-marked feature on Top View. 3. Dimensions b applies to metallized terminal and is measured between 0.15 mm and 0.30 mm from the terminal tip. If the terminal has the optional radius on the other end of the terminal, the dimension should not be measured in that radius area. 4. The Pin #1 ID on the Bottom View is an orientation feature on the thermal pad. SYMBOL MIN NOM MAX A 0.50 0.55 0.60 A1 0.0 0.02 0.05 A2 - - 0.55 D 1.90 2.00 2.10 D2 1.40 1.50 1.60 E 2.90 3.00 3.10 E2 1.20 1.30 1.40 b 0.18 0.25 0.30 C L 3 1.52 REF 0.30 e K NOTE 0.35 0.40 0.50 BSC 0.20 - - 11/26/14 Package Drawing Contact: packagedrawings@atmel.com 19 AT24C512C [DATASHEET] Atmel-8720G-SEEPROM-AT24C512C-Datasheet_092015 TITLE 8MA2, 8-pad 2 x 3 x 0.6mm Body, Thermally Enhanced Plastic Ultra Thin Dual Flat No-Lead Package (UDFN) GPC DRAWING NO. REV. YNZ 8MA2 G 13.5 8U-8 -- 8-ball WLCSP TOP VIEW BOTTOM VIEW A1 CORNER 1 -B- 2 3 4 5 5 4 3 2 A1 CORNER 1 A B E2 E A E1 C B C -A- Ob(8X) D2 D D1 d 0.015(4X) j n 0.015 m C n 0.05 m C A B SIDE VIEW d 0.075 C A A2 -C- A1 SEATING PLANE COMMON DIMENSIONS (Unit of Measure = mm) PIN ASSIGNMENT MATRIX 2 1 A VCC 4 SDA 5 A0 WP A1 SCL B C 3 A2 VSS SYMBOL MIN TYP MAX A 0.456 0.495 0.534 A1 0.16 - 0.22 A2 0.280 0.305 0.330 E Contact Atmel for details E1 0.866 E2 0.500 D Contact Atmel for details D1 1.000 D2 0.500 b NOTE 0.240 0.270 0.300 4/11/13 Package Drawing Contact: packagedrawings@atmel.com 20 AT24C512C [DATASHEET] Atmel-8720G-SEEPROM-AT24C512C-Datasheet_092015 TITLE 8U-8, 8-ball Wafer Level Chip Scale Package (WLCSP) GPC DRAWING NO. REV. GRX 8U-8 A 13.6 8U2-1 -- 8-ball VFBGA f 0.10 C d 0.10 A1 BALL PAD CORNER D A (4X) d 0.08 C C A1 BALL PAD CORNER 2 1 Ob A j n0.15 m C A B j n0.08 m C B e E C D (e1) B A1 d A2 (d1) A TOP VIEW BOTTOM VIEW SIDE VIEW 8 SOLDER BALLS COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL Notes: 1. This drawing is for general 2. Dimension 'b' is measured at the maximum solder ball diameter. 3. Solder ball composition shall be 95.5Sn-4.0Ag-.5Cu. A A1 A2 b D E e e1 d d1 MIN 0.81 0.15 0.40 0.25 NOM 0.91 0.20 0.45 0.30 2.35 BSC 3.73 BSC 0.75 BSC 0.74 REF 0.75 BSC 0.80 REF MAX NOTE 1.00 0.25 0.50 0.35 6/11/13 TITLE Package Drawing Contact: packagedrawings@atmel.com 8U2-1, 8-ball, 2.35 x 3.73 mm Body, 0.75 mm pitch, Very Thin, Fine-Pitch Ball Grid Array Package (VFBGA) GPC DRAWING NO. GWW 8U2-1 AT24C512C [DATASHEET] Atmel-8720G-SEEPROM-AT24C512C-Datasheet_092015 REV. G 21 14. Revision History Doc. Rev. Date 8720G 09/2015 8720F 01/2015 8720E 08/2013 Comments Added the AT24C512C-CUMHY-T package option. Added the UDFN expanded quantity option. Updated package outline drawings and the ordering information section. Correct spelling error. Correct subscript pin names on pinouts. Update the ICC1 and ICC2 supply currents in the DC Characteristics table. Added 8U-8 WLCSP package offering. 8720D 03/2013 Update related information throughout document. Update footers and disclaimer page. Update part markings. 8720C 07/2012 Update package drawings. Update template. 22 8720B 12/2010 8720A 09/2010 Replace part markings with single page standard marking. Remove five ordering code variations. Initial document release. AT24C512C [DATASHEET] Atmel-8720G-SEEPROM-AT24C512C-Datasheet_092015 XXXXXX Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA T: (+1)(408) 441.0311 F: (+1)(408) 436.4200 | www.atmel.com (c) 2015 Atmel Corporation. / Rev.: Atmel-8720G-SEEPROM-AT24C512C-Datasheet_092015. Atmel(R), Atmel logo and combinations thereof, Enabling Unlimited Possibilities(R), and others are registered trademarks or trademarks of Atmel Corporation in U.S. and other countries. Other terms and product names may be trademarks of others. DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where the failure of such products would reasonably be expected to result in significant personal injury or death ("Safety-Critical Applications") without an Atmel officer's specific written consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for the operation of nuclear facilities and weapons systems. Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.