IRFP140N TM Data Sheet March 2000 File Number 4841 33A, 100V, 0.040 Ohm, N-Channel Power MOSFET Packaging Features JEDEC TO-247 SOURCE DRAIN GATE * Ultra Low On-Resistance - rDS(ON) = 0.040, VGS = 10V * Simulation Models - Temperature Compensated PSPICETM and SABER(c) Electrical Models - Spice and SABER(c) Thermal Impedance Models - www.intersil.com * Peak Current vs Pulse Width Curve DRAIN (TAB) * UIS Rating Curve Ordering Information Symbol PART NUMBER D IRFP140N PACKAGE TO-247 BRAND IRFP140N G S Absolute Maximum Ratings TC = 25oC, Unless Otherwise Specified IRFP140N UNITS Drain to Source Voltage (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VDSS Drain to Gate Voltage (RGS = 20k) (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VDGR 100 V 100 V Gate to Source Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VGS 20 V Drain Current Continuous (TC= 25oC, VGS = 10V) (Figure 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ID Continuous (TC= 100oC, VGS = 10V) (Figure 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ID Pulsed Drain Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .IDM 33 23 Figure 4 A A Pulsed Avalanche Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .UIS Figures 6, 14, 15 Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PD Derate Above 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 0.80 W W/oC Operating and Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TJ, TSTG Maximum Temperature for Soldering Leads at 0.063in (1.6mm) from Case for 10s. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TL Package Body for 10s, See Techbrief TB334 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tpkg -55 to 175 oC 300 260 oC oC NOTES: 1. TJ = 25oC to 150oC. CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. 1 CAUTION: These devices are sensitive to electrostatic discharge. Follow proper ESD Handling Procedures. PSPICE(R) is a registered trademark of MicroSim Corporation. SABER(c) is a Copyright of Analogy Inc. 1-888-INTERSIL or 321-724-7143 | Intersil and Design is a trademark of Intersil Corporation. | Copyright (c) Intersil Corporation 2000 IRFP140N TC = 25oC, Unless Otherwise Specified Electrical Specifications PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS 100 - - V - - 1 A OFF STATE SPECIFICATIONS Drain to Source Breakdown Voltage Zero Gate Voltage Drain Current BVDSS IDSS Gate to Source Leakage Current IGSS ID = 250A, VGS = 0V (Figure 11) VDS = 95V, VGS = 0V VDS = 90V, VGS = 0V, TC = 150oC - - 250 A VGS = 20V - - 100 nA ON STATE SPECIFICATIONS Gate to Source Threshold Voltage VGS(TH) VGS = VDS, ID = 250A (Figure 10) 2 - 4 V Drain to Source On Resistance rDS(ON) ID = 33A, VGS = 10V (Figure 9) - 0.033 0.040 TO-247 - - 1.25 oC/W - - 30 oC/W - - 100 ns - 9.5 - ns - 57 - ns td(OFF) - 40 - ns tf - 55 - ns tOFF - - 145 ns - 66 79 nC - 35 42 nC THERMAL SPECIFICATIONS Thermal Resistance Junction to Case RJC Thermal Resistance Junction to Ambient RJA SWITCHING SPECIFICATIONS (VGS = 10V) Turn-On Time tON Turn-On Delay Time td(ON) Rise Time tr Turn-Off Delay Time Fall Time Turn-Off Time VDD = 50V, ID = 33A VGS = 10V, RGS = 9.1 (Figures 18, 19) GATE CHARGE SPECIFICATIONS Total Gate Charge Qg(TOT) VGS = 0V to 20V Gate Charge at 10V Qg(10) VGS = 0V to 10V Threshold Gate Charge Qg(TH) VGS = 0V to 2V VDD = 50V, ID = 33A, Ig(REF) = 1.0mA (Figures 13, 16, 17) - 2.4 2.9 nC Gate to Source Gate Charge Qgs - 5.4 - nC Gate to Drain "Miller" Charge Qgd - 13 - nC - 1220 - pF - 295 - pF - 100 - pF MIN TYP MAX UNITS ISD = 33A - - 1.25 V ISD = 17A - - 1.00 V trr ISD = 33A, dISD/dt = 100A/s - - 112 ns QRR ISD = 33A, dISD/dt = 100A/s - - 400 nC CAPACITANCE SPECIFICATIONS Input Capacitance CISS Output Capacitance COSS Reverse Transfer Capacitance CRSS VDS = 25V, VGS = 0V, f = 1MHz (Figure 12) Source to Drain Diode Specifications PARAMETER SYMBOL Source to Drain Diode Voltage VSD Reverse Recovery Time Reverse Recovered Charge 2 TEST CONDITIONS IRFP140N Typical Performance Curves 40 1.0 ID, DRAIN CURRENT (A) POWER DISSIPATION MULTIPLIER 1.2 0.8 0.6 0.4 VGS = 10V 30 20 10 0.2 0 0 25 50 75 100 150 125 0 175 TC , CASE TEMPERATURE (oC) 25 50 75 100 125 150 175 TC, CASE TEMPERATURE (oC) FIGURE 1. NORMALIZED POWER DISSIPATION vs CASE TEMPERATURE FIGURE 2. MAXIMUM CONTINUOUS DRAIN CURRENT vs CASE TEMPERATURE 2 ZJC, NORMALIZED THERMAL IMPEDANCE 1 DUTY CYCLE - DESCENDING ORDER 0.5 0.2 0.1 0.05 0.02 0.01 PDM 0.1 t1 t2 NOTES: DUTY FACTOR: D = t1/t2 PEAK TJ = PDM x ZJC x RJC + TC SINGLE PULSE 0.01 10-5 10-4 10-3 10-2 10-1 100 101 t, RECTANGULAR PULSE DURATION (s) FIGURE 3. NORMALIZED MAXIMUM TRANSIENT THERMAL IMPEDANCE IDM, PEAK CURRENT (A) 600 TC = 25oC FOR TEMPERATURES ABOVE 25oC DERATE PEAK CURRENT AS FOLLOWS: 175 - TC I = I25 150 100 VGS = 10V TRANSCONDUCTANCE MAY LIMIT CURRENT IN THIS REGION 20 10-5 10-4 10-3 10-2 t, PULSE WIDTH (s) FIGURE 4. PEAK CURRENT CAPABILITY 3 10-1 100 101 IRFP140N Typical Performance Curves (Continued) 200 If R = 0 tAV = (L)(IAS)/(1.3*RATED BVDSS - VDD) If R 0 tAV = (L/R)ln[(IAS*R)/(1.3*RATED BVDSS - VDD) +1] IAS, AVALANCHE CURRENT (A) ID, DRAIN CURRENT (A) 300 SINGLE PULSE TJ = MAX RATED TC = 25oC 100 100s 10 OPERATION IN THIS AREA MAY BE LIMITED BY rDS(ON) 1ms 10ms 100 10 STARTING TJ = 150oC 0.01 300 VDS, DRAIN TO SOURCE VOLTAGE (V) 0.1 FIGURE 6. UNCLAMPED INDUCTIVE SWITCHING CAPABILITY 60 60 VGS = 20V VGS = 10V ID, DRAIN CURRENT (A) PULSE DURATION = 80s DUTY CYCLE = 0.5% MAX VDD = 15V 40 TJ = 175oC 20 TJ = -55oC VGS = 7V VGS = 6V 40 VGS =5V 20 PULSE DURATION = 80s DUTY CYCLE = 0.5% MAX TC = 25oC TJ = 25oC 0 0 2 3 4 5 VGS, GATE TO SOURCE VOLTAGE (V) 0 6 FIGURE 7. TRANSFER CHARACTERISTICS 3.0 PULSE DURATION = 80s DUTY CYCLE = 0.5% MAX 1 2 3 VDS, DRAIN TO SOURCE VOLTAGE (V) 4 FIGURE 8. SATURATION CHARACTERISTICS 1.2 VGS = 10V, ID = 33A VGS = VDS, ID = 250A 2.5 NORMALIZED GATE THRESHOLD VOLTAGE NORMALIZED DRAIN TO SOURCE ON RESISTANCE 1 tAV, TIME IN AVALANCHE (ms) NOTE: Refer to Intersil Application Notes AN9321 and AN9322. FIGURE 5. FORWARD BIAS SAFE OPERATING AREA ID, DRAIN CURRENT (A) STARTING TJ = 25oC 10 0.001 1 1 100 2.0 1.5 1.0 0.8 1.0 0.6 0.5 -80 -40 160 0 40 80 120 TJ, JUNCTION TEMPERATURE (oC) FIGURE 9. NORMALIZED DRAIN TO SOURCE ON RESISTANCE vs JUNCTION TEMPERATURE 4 200 -80 -40 0 40 80 120 160 200 TJ, JUNCTION TEMPERATURE (oC) FIGURE 10. NORMALIZED GATE THRESHOLD VOLTAGE vs JUNCTION TEMPERATURE IRFP140N Typical Performance Curves (Continued) 4000 VGS = 0V, f = 1MHz ID = 250A C, CAPACITANCE (pF) NORMALIZED DRAIN TO SOURCE BREAKDOWN VOLTAGE 1.2 1.1 1.0 1000 CISS = CGS + CGD COSS CDS + CGD 100 CRSS = CGD 0.9 -80 -40 0 40 80 160 120 20 0.1 200 TJ , JUNCTION TEMPERATURE (oC) 1.0 10 100 VDS , DRAIN TO SOURCE VOLTAGE (V) FIGURE 11. NORMALIZED DRAIN TO SOURCE BREAKDOWN VOLTAGE vs JUNCTION TEMPERATURE FIGURE 12. CAPACITANCE vs DRAIN TO SOURCE VOLTAGE VGS , GATE TO SOURCE VOLTAGE (V) 10 VDD = 50V 8 6 4 WAVEFORMS IN DESCENDING ORDER: ID = 33A ID = 17A 2 0 10 0 20 30 Qg, GATE CHARGE (nC) 40 NOTE: Refer to Intersil Application Notes AN7254 and AN7260. FIGURE 13. GATE CHARGE WAVEFORMS FOR CONSTANT GATE CURRENT Test Circuits and Waveforms VDS BVDSS L VARY tP TO OBTAIN REQUIRED PEAK IAS tP + RG VDS IAS VDD VDD - VGS DUT 0V tP IAS 0 0.01 tAV FIGURE 14. UNCLAMPED ENERGY TEST CIRCUIT 5 FIGURE 15. UNCLAMPED ENERGY WAVEFORMS IRFP140N Test Circuits and Waveforms (Continued) VDS VDD RL Qg(TOT) VDS VGS = 20V VGS Qg(10) + VDD VGS = 10V VGS DUT VGS = 2V Ig(REF) 0 Qg(TH) Qgs Qgd Ig(REF) 0 FIGURE 16. GATE CHARGE TEST CIRCUIT FIGURE 17. GATE CHARGE WAVEFORMS VDS tON tOFF td(ON) td(OFF) tf tr RL VDS 90% 90% + VGS VDD - 10% 10% 0 DUT 90% RGS VGS VGS 0 FIGURE 18. SWITCHING TIME TEST CIRCUIT 6 10% 50% 50% PULSE WIDTH FIGURE 19. SWITCHING TIME WAVEFORM IRFP140N PSPICE Electrical Model .SUBCKT IRFP140N 2 1 3 ; rev 15 Jan 2000 CA 12 8 1.95e-9 CB 15 14 1.90e-9 CIN 6 8 1.12e-9 DBODY 7 5 DBODYMOD DBREAK 5 11 DBREAKMOD DPLCAP 10 5 DPLCAPMOD LDRAIN DPLCAP DRAIN 2 5 10 5 51 ESLC 11 - RDRAIN 6 8 EVTHRES + 19 8 + LGATE GATE 1 EVTEMP RGATE + 18 22 9 20 21 DBODY - 16 MWEAK 6 MMED MSTRO RLGATE MMED 16 6 8 8 MMEDMOD MSTRO 16 6 8 8 MSTROMOD MWEAK 16 21 8 8 MWEAKMOD + 17 EBREAK 18 50 - IT 8 17 1 LSOURCE CIN 8 SOURCE 3 7 RSOURCE RBREAK 17 18 RBREAKMOD 1 RDRAIN 50 16 RDRAINMOD 2.00e-2 RGATE 9 20 1.77 RLDRAIN 2 5 10 RLGATE 1 9 26 RLSOURCE 3 7 11 RSLC1 5 51 RSLCMOD 1e-6 RSLC2 5 50 1e3 RSOURCE 8 7 RSOURCEMOD 6.5e-3 RVTHRES 22 8 RVTHRESMOD 1 RVTEMP 18 19 RVTEMPMOD 1 S1A S1B S2A S2B DBREAK + RSLC2 ESG LDRAIN 2 5 1.0e-9 LGATE 1 9 6.19e-9 LSOURCE 3 7 2.18e-9 RLDRAIN RSLC1 51 EBREAK 11 7 17 18 112.8 EDS 14 8 5 8 1 EGS 13 8 6 8 1 ESG 6 10 6 8 1 EVTHRES 6 21 19 8 1 EVTEMP 20 6 18 22 1 RLSOURCE S2A S1A 12 S1B CA 17 18 RVTEMP S2B 13 CB 6 8 EGS 19 VBAT 5 8 EDS - - IT 14 + + 6 12 13 8 S1AMOD 13 12 13 8 S1BMOD 6 15 14 13 S2AMOD 13 15 14 13 S2BMOD RBREAK 15 14 13 13 8 - + 8 22 RVTHRES VBAT 22 19 DC 1 ESLC 51 50 VALUE={(V(5,51)/ABS(V(5,51)))*(PWR(V(5,51)/(1e-6*71),3.5))} .MODEL DBODYMOD D (IS = 1.20e-12 RS = 4.2e-3 XTI = 5 TRS1 = 1.3e-3 TRS2 = 8.0e-6 CJO = 1.50e-9 TT = 7.47e-8 M = 0.63) .MODEL DBREAKMOD D (RS = 4.2e-1 TRS1 = 8e-4 TRS2 = 3e-6) .MODEL DPLCAPMOD D (CJO = 1.45e-9 IS = 1e-30 M = 0.82) .MODEL MMEDMOD NMOS (VTO = 3.11 KP = 5 IS = 1e-30 N = 10 TOX = 1 L = 1u W = 1u RG = 1.77) .MODEL MSTROMOD NMOS (VTO = 3.57 KP = 33.5 IS = 1e-30 N = 10 TOX = 1 L = 1u W = 1u) .MODEL MWEAKMOD NMOS (VTO = 2.68 KP = 0.09 IS = 1e-30 N = 10 TOX = 1 L = 1u W = 1u RG = 17.7 ) .MODEL RBREAKMOD RES (TC1 =1.05e-3 TC2 = -5e-7) .MODEL RDRAINMOD RES (TC1 = 9.40e-3 TC2 = 2.93e-5) .MODEL RSLCMOD RES (TC1 = 3.5e-3 TC2 = 2.0e-6) .MODEL RSOURCEMOD RES (TC1 = 1e-3 TC2 = 1e-6) .MODEL RVTHRESMOD RES (TC1 = -1.8e-3 TC2 = -8.6e-6) .MODEL RVTEMPMOD RES (TC1 = -3.0e-3 TC2 =1.5e-7) .MODEL S1AMOD VSWITCH (RON = 1e-5 .MODEL S1BMOD VSWITCH (RON = 1e-5 .MODEL S2AMOD VSWITCH (RON = 1e-5 .MODEL S2BMOD VSWITCH (RON = 1e-5 ROFF = 0.1 ROFF = 0.1 ROFF = 0.1 ROFF = 0.1 VON = -6.2 VOFF= -3.1) VON = -3.1 VOFF= -6.2) VON = -1.0 VOFF= 0.5) VON = 0.5 VOFF= -1.0) .ENDS NOTE: For further discussion of the PSPICE model, consult A New PSPICE Sub-Circuit for the Power MOSFET Featuring Global Temperature Options; IEEE Power Electronics Specialist Conference Records, 1991, written by William J. Hepp and C. Frank Wheatley. 7 IRFP140N SABER Electrical Model REV 15 Jan 2000 template IRFP140N n2,n1,n3 electrical n2,n1,n3 { var i iscl d..model dbodymod = (is = 1.20e-12, cjo = 1.50e-9, tt = 7.47e-8, xti = 5, m = 0.63) d..model dbreakmod = () d..model dplcapmod = (cjo = 1.45e-9, is = 1e-30, m = 0.82) m..model mmedmod = (type=_n, vto = 3.11, kp = 5, is = 1e-30, tox = 1) m..model mstrongmod = (type=_n, vto = 3.57, kp = 33.5, is = 1e-30, tox = 1) m..model mweakmod = (type=_n, vto = 2.68, kp = 0.09, is = 1e-30, tox = 1) sw_vcsp..model s1amod = (ron = 1e-5, roff = 0.1, von = -6.2, voff = -3.1) DPLCAP sw_vcsp..model s1bmod = (ron =1e-5, roff = 0.1, von = -3.1, voff = -6.2) 10 sw_vcsp..model s2amod = (ron = 1e-5, roff = 0.1, von = -1.0, voff = 0.5) sw_vcsp..model s2bmod = (ron = 1e-5, roff = 0.1, von = 0.5, voff = -1.0) c.ca n12 n8 = 1.95e-9 c.cb n15 n14 = 1.90e-9 c.cin n6 n8 = 1.12e-9 LDRAIN DRAIN 2 5 RSLC1 51 RLDRAIN RDBREAK RSLC2 72 ISCL EVTHRES + 19 8 + i.it n8 n17 = 1 LGATE GATE 1 l.ldrain n2 n5 = 1e-9 l.lgate n1 n9 = 6.19e-9 l.lsource n3 n7 = 2.18e-9 RDRAIN 6 8 ESG EVTEMP RGATE + 18 22 9 20 16 MWEAK DBODY EBREAK + 17 18 MSTRO CIN 71 11 MMED m.mmed n16 n6 n8 n8 = model=mmedmod, l=1u, w=1u m.mstrong n16 n6 n8 n8 = model=mstrongmod, l=1u, w=1u m.mweak n16 n21 n8 n8 = model=mweakmod, l=1u, w=1u - 8 LSOURCE 7 RSOURCE RLSOURCE S1A 12 S2A 13 8 S1B CA RBREAK 15 14 13 17 18 RVTEMP S2B 13 CB 6 8 EGS 19 - sw_vcsp.s1a n6 n12 n13 n8 = model=s1amod sw_vcsp.s1b n13 n12 n13 n8 = model=s1bmod sw_vcsp.s2a n6 n15 n14 n13 = model=s2amod sw_vcsp.s2b n13 n15 n14 n13 = model=s2bmod v.vbat n22 n19 = dc=1 equations { i (n51->n50) +=iscl iscl: v(n51,n50) = ((v(n5,n51)/(1e-9+abs(v(n5,n51))))*((abs(v(n5,n51)*1e6/71))** 3.5)) } } - IT 14 + + spe.ebreak n11 n7 n17 n18 = 112.8 spe.eds n14 n8 n5 n8 = 1 spe.egs n13 n8 n6 n8 = 1 spe.esg n6 n10 n6 n8 = 1 spe.evtemp n20 n6 n18 n22 = 1 spe.evthres n6 n21 n19 n8 = 1 8 21 6 RLGATE res.rbreak n17 n18 = 1, tc1 = 1.05e-3, tc2 = -5.0e-7 res.rdbody n71 n5 = 4.2e-3, tc1 = 1.30e-3, tc2 = 8.0e-6 res.rdbreak n72 n5 = 4.2e-1, tc1 = 8.0e-4, tc2 = 3.0e-6 res.rdrain n50 n16 = 2.00e-2, tc1 = 9.40e-3, tc2 = 2.93e-5 res.rgate n9 n20 = 1.77 res.rldrain n2 n5 = 10 res.rlgate n1 n9 = 26 res.rlsource n3 n7 = 11 res.rslc1 n5 n51 = 1e-6, tc1 = 3.5e-3, tc2 = 2.0e-6 res.rslc2 n5 n50 = 1e3 res.rsource n8 n7 = 6.5e-3, tc1 = 1e-3, tc2 = 1e-6 res.rvtemp n18 n19 = 1, tc1 = -3.0e-3, tc2 = 1.5e-7 res.rvthres n22 n8 = 1, tc1 = -1.8e-3, tc2 = -8.6e-6 DBREAK 50 - d.dbody n7 n71 = model=dbodymod d.dbreak n72 n11 = model=dbreakmod d.dplcap n10 n5 = model=dplcapmod RDBODY VBAT 5 8 EDS - + 8 22 RVTHRES SOURCE 3 IRFP140N SPICE Thermal Model th REV 15 Jan 2000 JUNCTION IRFP140NT CTHERM1 th 6 2.60e-3 CTHERM2 6 5 8.85e-3 CTHERM3 5 4 7.60e-3 CTHERM4 4 3 7.65e-3 CTHERM5 3 2 1.22e-2 CTHERM6 2 tl 8.70e-2 RTHERM1 CTHERM1 6 RTHERM1 th 6 9.00e-3 RTHERM2 6 5 1.80e-2 RTHERM3 5 4 9.15e-2 RTHERM4 4 3 2.43e-1 RTHERM5 3 2 3.10e-1 RTHERM6 2 tl 3.21e-1 RTHERM2 CTHERM2 5 SABER Thermal Model RTHERM3 CTHERM3 SABER thermal model IRFP140NT template thermal_model th tl thermal_c th, tl { ctherm.ctherm1 th 6 = 2.60e-3 ctherm.ctherm2 6 5 = 8.85e-3 ctherm.ctherm3 5 4 = 7.60e-3 ctherm.ctherm4 4 3 = 7.65e-3 ctherm.ctherm5 3 2 = 1.22e-2 ctherm.ctherm6 2 tl = 8.70e-2 4 RTHERM4 CTHERM4 3 rtherm.rtherm1 th 6 = 9.00e-3 rtherm.rtherm2 6 5 = 1.80e-2 rtherm.rtherm3 5 4 = 9.15e-2 rtherm.rtherm4 4 3 = 2.43e-1 rtherm.rtherm5 3 2 = 3.10e-1 rtherm.rtherm6 2 tl = 3.21e-1 } RTHERM5 CTHERM5 2 RTHERM6 CTHERM6 tl 9 CASE IRFP140N TO-247 3 LEAD JEDEC STYLE TO-247 PLASTIC PACKAGE A E SYMBOL OP Q OR D L1 b1 c 2 1 3 3 J1 e MAX MILLIMETERS MIN MAX NOTES 0.180 0.190 4.58 4.82 - b 0.046 0.051 1.17 1.29 2, 3 b1 0.060 0.070 1.53 1.77 1, 2 b2 0.095 0.105 2.42 2.66 1, 2 c 0.020 0.026 0.51 0.66 1, 2, 3 D 0.800 0.820 20.32 20.82 - E 0.605 0.625 15.37 15.87 e1 b MIN A e b2 L INCHES TERM. 4 OS 0.219 TYP 0.438 BSC 5.56 TYP 11.12 BSC 4 4 J1 0.090 0.105 2.29 2.66 1 L 0.620 0.640 15.75 16.25 - BACK VIEW L1 0.145 0.155 3.69 3.93 1 OP 0.138 0.144 3.51 3.65 - Q 0.210 0.220 5.34 5.58 - OR 0.195 0.205 4.96 5.20 - OS 0.260 0.270 6.61 6.85 - 2 e1 5 NOTES: 1. Lead dimension and finish uncontrolled in L1. 2. Lead dimension (without solder). 3. Add typically 0.002 inches (0.05mm) for solder coating. 4. Position of lead to be measured 0.250 inches (6.35mm) from bottom of dimension D. 5. Position of lead to be measured 0.100 inches (2.54mm) from bottom of dimension D. 6. Controlling dimension: Inch. 7. Revision 1 dated 1-93. All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site www.intersil.com Sales Office Headquarters NORTH AMERICA Intersil Corporation P. O. Box 883, Mail Stop 53-204 Melbourne, FL 32902 TEL: (321) 724-7000 FAX: (321) 724-7240 10 EUROPE Intersil SA Mercure Center 100, Rue de la Fusee 1130 Brussels, Belgium TEL: (32) 2.724.2111 FAX: (32) 2.724.22.05 ASIA Intersil (Taiwan) Ltd. 7F-6, No. 101 Fu Hsing North Road Taipei, Taiwan Republic of China TEL: (886) 2 2716 9310 FAX: (886) 2 2715 3029