1.27 PCS series mm Pitch 1.27 mm Pitch Connectors Connectors Outline PCS series provides various 1.27 mm pitch smaller-sized high density interface connectors specifically designed for downsized electronic equipment. Features * 20 - 96 contacts for board-to-cable connectors * Results in substantial labor saving; IDC type connection is standard for cables. (AWG #28 or #30) * Soldering type connectors available * EMI-filtered design to meet FCC and other standards * Backshell has a robust interface structure. * Quick locking with metal latch * Panel-to-cable connectors available * Accessory is available for preventing connector misinsertion. * 34 - 150 contacts for board-to-cable connectors. * Even with many contacts, connectors can be easily inserted or extracted due to a low insertion force design. * Drainage structure ensures cleaning solution does not remain in the housing during flux removal. (For molded type male connectors) Principal Applications Electrical Characteristics Office automation equipment, instrumentation equipment, communications equipment, factory automation, etc. Rated voltage 250V AC (r.m.s.) Rated current 1A Insulation resistance Dielectric withstanding voltage Contact resistance Over 1000 megohms at 100V DC 750V AC (r.m.s.) for PCS series 500V AC (r.m.s.) for PCS-XE series 35 milliohms or less (not applicable to some products) Document Disclaimer When placing orders with us, minimum order quantities are set for every product. Be sure to contact us before starting preliminary design of PCBs using our connectors. The specifications and information shown in the catalog are subject to change without notice. Reflow temperature profile (for reference purposes) Flow temperature profile (for reference purposes) 5sec 2605C (Peak) 250C 220C 100~130C 130~150C (Preheating period) 60~120sec (Full heating period) 30sec 30~60sec The reflow temperature profile shown in this drawing is for reference purposes. This profile depends on requirements such as reflow equipment, soldering paste, and PCB size. Thus, this profile may not meet with your specific situation. Please evaluate your PCB-mounting soldering and set your own reflow temperature profile. The flow temperature profile as shown above is for reference purposes. This profile depends on requirements such as the PCB size. Thus, this profile may not meet with your specific situation. Please evaluate your PCB-mounting soldering and set your own flow temperature profile. Applicable products PCS-XE( )SLFYTU( )+ Applicable products PCS series through hole type connector The profile shown in this drawing is applicable only for those products shown above. The profile shown in this drawing is applicable only for those products shown above. Dimensions of connector mounting for reference purposes Board-to-board connector dimensions for reference purposes PCS-( )MD+ PCS-( )FD+ PCS-( )LMD+ PCS-( )FD+ 23.1 14.9 PCS-( )MD+ 22.215 PCS-( )LMD+ PCS-( )LFD+ 21.3 PCS-( )LFD+ 29.5 27.53 20.215 Board-to-cable connector dimensions for reference purposes (In the case of spring-locked type) 10 or more B C 2.7 Panel thickness: t=1.6 mm MAX. Number of contacts Edge of PCB A B C 20 35 or more 28 40 or more 36 45.1 or more 50 54 or more 68 65.4 or more 80 73 or more 96 83.2 or more 40.5 or more 51.2 or more 35.5 or more 46.2 or more A Panel mounting-hole dimensions for reference purposes (In the case of PCS-E type) B A Number of contacts A B C 20 27.4 23.7 11.3 28 32.5 28.8 16.3 36 37.6 33.9 20.3 C 50 46.5 42.8 30.3 B 68 57.9 54.2 40.3 A 80 65.5 61.8 50.3 96 75.69 72.0 2.8 15 R1.4 7.5 2.8 7.5 R1.4 In the case of using a mating guide Product List Straight through hole type male connector for PCB PCS-( )MD+ Straight through hole type female connector for PCB PCS-( )FD+ Right-angle through hole type male connector for PCB PCS-( )LMD+ Right-angle through hole type female connector for PCB PCS-( )LFD+ B-10PCS PCS series...8 B-11PCS PCS series...9 B-12PCS PCS series...10 B-13PCS PCS series...11 Right-angle through hole type male connector for PCB PCS-128LMDT-GP+ Right-angle through hole type female connector for PCB PCS-128LFDT-GP+ Straight through hole type male connector for PCB PCS-E( )MD+ Right-angle through hole type male connector for PCB PCS-E( )LMD+ B-14PCS PCS series...12 B-15PCS PCS series...13 B-16PCS PCS series...14 B-17PCS PCS series...15 IDC type female connector for cable PCS-E( )F( ) Soldering type female connector for cable PCS-E( )FS+ IDC type male connector for panel PCS-E( )PM( )-( ) IDC type male connector for cable PCS-D( )( )MA1( )+ B-18PCS PCS series...16 B-19PCS PCS series...17 B-20PCS PCS series...18 B-21PCS PCS series...19 IDC type female connector for cable PCS-D68( )FA1( )+ Straight through hole type female connector for PCB PCS-XE( )SFD( )( )+ Straight through hole type female connector for PCB PCS-XE( )SFD( )N( )+ Right-angle through hole type female connector for PCB PCS-XE( )LFD( )( )+ B-22PCS PCS series...20 B-23PCS PCS series...21 B-24PCS PCS series...22 B-25PCS PCS series...23 Right-angle through hole type female connector for PCB PCS-XE68LFDT( )N( )+ Right-angle through hole type female connector for PCB PCS-XE100LFD( )-( )+ Right-angle through hole type female connector for PCB PCS-XE( )SLFD( )( )+ Right-angle through hole type female connector for PCB PCS-XE( )SLFDT( )( )+ B-26PCS PCS series...24 B-27PCS PCS series...25 B-28PCS PCS series...26 B-29PCS PCS series...27 Right-angle through hole type female connector for PCB PCS-XE( )SLFDT( )N( )+ Right-angle SMT type female connector for PCB PCS-XE( )SLFYTU( )+ Straight Press-in type female connector for PCB PCS-XE50SFP( )( ) B-30PCS PCS series...28 B-31PCS PCS series...29 B-32PCS PCS series...30 B-33PCS PCS series...31 IDC type male connector for cable PCS-XE( )M( )( )+ Soldering type male connector for cable PCS-XES68MS+ IDC type female connector for panel PCS-XE( )SPF( )1UN( ) IDC type female connector for panel PCS-XE( )SPF( )( )( ) B-34PCS PCS series...32 B-35PCS PCS series...33 B-36PCS PCS series...34 B-37PCS PCS series...35 IDC type female connector for panel PCS-XED( )( )FA( )( )+ IDC type female connector for panel PCS-XED68( )FAUN( )+ B-38PCS PCS series...36 B-39PCS PCS series...37 EMI-filtered vertical type die-cast material backshell for standard cable PCS-E( )L( ) B-40PCS PCS series...38 Vertical type die-cast material backshell for larger diameter cable PCS-E( )LK B-41PCS PCS series...39 Mating guide structure vertical type die-cast material backshell for standard cable PCS-E( )LG( ) B-42PCS PCS series...40 Horizontal type die-cast material backshell for standard cable PCS-E( )W B-43PCS PCS series...41 Vertical type plastic backshell for flat cable PCS-E( )LT+ B-44PCS PCS series...42 Vertical type die-cast material backshell for cable extension PCS-E( )PML( ) B-45PCS PCS series...43 Vertical type die-cast material backshell for standard cable with provision for preventing misinsertion PCS-E( )LP( )-( )+R B-46PCS PCS series...44 Vertical type die-cast material backshell for larger diameter cable with provision for preventing misinsertion PCS-E( )LKP( )-( )+R B-47PCS PCS series...45 Vertical type die-cast material backshell for larger diameter cable with mating guide for preventing misinsertion PCS-E96LKP( )-( )+R B-48PCS PCS series...46 Vertical type die-cast material backshell for larger diameter cable with provision for preventing misinsertion PCS-E96LKP1A-( )+R B-49PCS PCS series...47 PCS Right-angle through hole type female connector for PCB PCS-XE( )SLFD( )N( )+ PCS Vertical type die-cast material backshell for standard cable with mating guide for preventing misinsertion PCS-E( )LGP( )-( )+R B-50PCS PCS series...48 Horizontal type die-cast material backshell for standard cable with provision for preventing misinsertion PCS-E( )WSP-( )+R B-51PCS PCS series...49 Horizontal type die-cast material backshell for larger diameter cable with provision for preventing misinsertion PCS-E( )WKP( )-( )+R B-52PCS PCS series...50 Horizontal type die-cast material backshell for larger diameter cable with provision for preventing misinsertion PCS-E96WKP( )-( )+R B-53PCS PCS series...51 Vertical type die-cast material backshell for flat cable with provision for preventing misinsertion PCS-E( )LTP-( )+R B-54PCS PCS series...52 Vertical type die-cast material backshell for larger diameter cable PCS-E68LKAU2N B-55PCS PCS series...53 Vertical type over-molded backshell PCS-XEM( )DL( )( )N Vertical type over-molded backshell PCS-XEM100L( )( ) B-56PCS PCS series...54 B-57PCS PCS series...55 Vertical type die-cast material backshell for daisy chain connection PCS-SE68LDAU2N B-58PCS PCS series...56 Dust-proof cap PCS-68C Dust-proof cap PCS-E( )C( ) Dust-proof cap PCS-E( )CP( ) B-59PCS PCS series...57 B-60PCS PCS series...58 B-61PCS PCS series...59 1.6 mm panel-thickness mating guide PCS-E( )G 1.0 mm panel-thickness mating guide PCS-E( )G1 Metallic mating guide PCS-E( )G3( ) B-62PCS PCS series...60 B-63PCS PCS series...61 B-64PCS PCS series...62 Metallic mating guide with provision for preventing misinsertion PCS-E( )G4-( ) B-65PCS PCS series...63 Key rivet for preventing misinsertion PCS-E-PK+R Misinsertion prevention guide PCS-E( )PG-( ) Misinsertion prevention guide PCS-E96PG-( ) Spacer hardware for male connector PCS-E( )M-SP B-66PCS PCS series...64 B-67PCS PCS series...65 B-68PCS PCS series...66 B-69PCS PCS series...67 Plug-in type terminator PCS-68FTH014X+ B-70PCS PCS series...68 B-71PCS PCS series...69 PCS Screw lock PCS-XE50SJ( )U2 1.27 mm pitch connector Straight through hole type male connector for PCB PCS-( )MD+ For PCB Straight Through hole Configuration of product Part No. PCS- ( ) MD+ Series name No. of contacts: 34, 48, 68, 96 or 150 Type of connector MD: Straight through hole type, male A B POS.#1 96M 7.3 5.7 HONDA 2.54 1.27 POS.#2 LAST POS. 15 4-R1 9.3 C 3.4 oe0.4 1.27 1.9053 B LAST POS. Terminal No. 1 POS.#1 Form of connectors other than 96-contact connector POS.#2 + -0.1 B LAST POS. + 1.27 0.05 POS.#2 - POS.#1 1.9050.053 For 34-contact connector + o0.8 0.06 LAST POS. - Recommended PCB layout (Connector side) t = 1.6 mm Components Contacts Insulator Because some combinations of "Configurations of Product Part No.", are under consideration for development, please contact us for availability details. Mating connectors: PCS series PCB-side through hole type female connector Accessories: Dust-proof cap, PCS-( )C Through hole SMT LAST POS. For 34-contact connector Press-in IDC Wire Soldering Crimping wrapping Others Dimensions Part No. PCS-34MD+ A 31.63 B 20.32 C 24.69 PCS-48MD+ 40.52 29.21 33.58 PCS-68MD+ 53.22 41.91 46.28 PCS-96MD+ 71.0 59.69 64.06 PCS-150MD+ 105.29 93.98 98.35 1.27 mm pitch connector Straight through hole type female connector for PCB PCS-( )FD+ Straight Through hole PCS For PCB Configuration of product Part No. PCS- ( ) FD+ Series name No. of contacts: 34, 48, 68, 96 or 150 Type of connector FD: Straight through hole type, female A B 2.54 1.27 POS.#1 7.3 5.5 POS.#2 LAST POS. 3.4 5.0 5.6 10.6 REF. 4-R0.9 15 C 0.40.35 1.27 1.9053 B LAST POS. LAST POS. For 34-contact connector POS.#1 POS.#2 B + -0.1 + -0.05 POS.#2 LAST POS. For 34-contact connector + o0.8 0.06 LAST POS. - Recommended PCB layout (Connector side) POS.#1 1.9050.053 1.27 t = 1.6 mm Components Insulator Contact Because some combinations of "Configurations of Product Part No.", are under consideration for development, please contact us for availability details. Dimensions Part No. PCS-34FD+ 31.63 A B 20.32 C 24.49 PCS-48FD+ 40.52 29.21 33.38 PCS-68FD+ 53.22 41.91 46.08 PCS-96FD+ 71.0 59.69 63.86 PCS-150FD+ 105.29 93.98 98.15 Mating connectors: PCS series straight through hole type male connector for PCB (Stacked height: 14.9 mm) PCS series right-angle through hole type male connector for PCB Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole PCS PCS PCS PCS PCS PCS PCS PCS PCS PCS PCS PCS PCS 1.27 mm pitch connector Right-angle through hole type male connector for PCB PCS-( )LMD+ For PCB Right-angle Through hole Configuration of product Part No. PCS- ( ) LMD+ Series name No. of contacts: 34, 48, 68 or 96 Type of connector LMD: Right-angle through hole type, male A B 2.54 3.4 POS. #marking (4 PLCS) 1.27 POS.#2 7.3 5.7 POS.#1 LAST POS. 4-R1 15 C oe0.4 10.9 17.5 LAST POS. 1.27 POS.#2 LAST POS. For 34-contact connector (10.5MAX) Board-edge + o0.8 0.06 - 1.9050.053 B POS.#1 LAST POS. 1.9053 LAST POS. For 34-contact connector Dimensions + 1.27 0.05 POS.#2 - Components + B 0.1 - Insulator Contacts Recommended PCB layout (Connector side) Bracket t = 1.6 mm Mating connectors: PCS series straight through hole type female connector for PCB PCS series right-angle through hole type female connector for PCB Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others POS.#1 Part No. PCS-34LMD+ A 31.63 B 20.32 C 24.69 PCS-48LMD+ 40.52 29.21 33.58 PCS-68LMD+ 53.22 41.91 46.28 PCS-96LMD+ 71.0 59.69 64.06 1.27 mm pitch connector Right-angle through hole type female connector for PCB PCS-( )LFD+ For PCB Right-angle Through hole Configuration of product Part No. PCS- ( ) LFD+ Series name No. of contacts: 34, 48, 68 or 96 Type of connector LFD: Right-angle through hole type, female A B 2.54 1.27 POS.#1 POS.#2 3.4 7.3 5.5 LAST POS. 15 C 4-R0.9 0.354 5.2 5.0 1.9053 17.0 LAST POS. For 34-contact connector POS.#2 1.27 B POS.#1 LAST POS. LAST POS. LAST POS. (4.8MAX.) Board-edge POS.#2 + o0.8 0.06 + - 1.27 0.05 - POS.#1 Components Insulator Contacts Bracket 1.9050.053 For 34-contact connector B + -0.1 Recommended PCB layout (Connector side) t = 1.6 mm Dimensions Part No. PCS-34LFD+ A 31.63 B 20.32 C 24.49 PCS-48LFD+ 40.52 29.21 33.38 PCS-68LFD+ 53.22 41.91 46.08 PCS-96LFD+ 71.0 59.69 63.86 Mating connectors: PCS series straight through hole type male connector for PCB PCS series right-angle through hole type male connector for PCB Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole 1.27 mm pitch connector Right-angle through hole type male connector for PCB PCS-128LMDT-GP+ For PCB Right-angle Through hole Configuration of product Part No. PCS- 128 LMD T- GP+ Series name No. of contacts: 128 Type of connector LMD: Right-angle through hole type, male Lock pin Mating guide 92.93 POS.#2 POS.#1 LAST POS. 1.1 1.1 2.54 1.27 (10.4 MAX.) 3.5 1 4 7.3 5.7 2-o2.30.1 80.01 1.9050.053 + o0.8 0.06 - 80.010.1 LAST POS. 0.1 88.9 Recommended PCB layout (Connector side) t = 1.6 mm 89.52 1 82.86 10.9 4.5 17.5 21.9 REF. 4.4 3.2 2.5 84.65 85.75 88.9 Components Insulator Contacts Bracket Lock pin Mating connectors: PCS-128LFDT-GP+ Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others oe0.4 POS.#2 POS.#1 1.9053 LAST POS. 3.4 3.65 POS.#2 POS.#1 1.27 mm pitch connector Right-angle through hole type female connector for PCB PCS-128LFDT-GP+ For PCB Right-angle Through hole Configuration of product Part No. PCS- 128 LFD T- GP+ Series name No. of contacts: 128 Type of connector LFD: Right-angle through hole type, female Lock pin Mating guide 92.93 89.92 82.76 POS.#2 2-o2.30.1 (4.7 MAX.) POS.#1 1 1.27 1.9050.053 7.3 5.5 3.7 1 2.54 80.01 LAST POS. POS.#2 POS.#1 LAST POS. 80.010.1 4.2 o0.80.06 88.90.1 Recommended PCB layout (Connector side) t = 1.6 mm 86.75 88.9 POS.#2 POS.#1 1.9053 LAST POS. 0.350.4 17 5.2 5 4.5 84.85 2.3 3.4 3.65 Components Insulator Contacts Bracket Lock pin Mating connectors: PCS-128LMDT-GP+ Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole 1.27 mm pitch connector Straight through hole type male connector for PCB PCS-E( )MD+ For PCB Straight Through hole Configuration of product Part No. PCS-E ( ) MD+ Series name No. of contacts: 20, 28, 36, 50 or 68 Type of connector MD: Straight through hole type, male A B C 1.27 POS.#2 7.0 2-M2.50.45 5.7 2.54 10.5 POS.#1 15 LAST POS. 4-R1 D E 0.85 5.5 4.0 1.27 oe0.4 1.9053 C 3.4 9.3 0.85 E LAST POS. LAST POS. Except 50-contact connector POS.#1 POS.#2 Except 50-contact connector + B 0.1 + C 0.1 - - POS.#1 + 1.27 0.05 - LAST POS. 1.9050.053 POS.#2 Components Contacts Insulator Shell 2-o2.8 + -0.06 o0.8 Dimensions LAST POS. Recommended PCB layout (Connector side) t = 1.6 mm Mating connectors: PCS-E series cable-side IDC type female connector PCS-E series cable-side soldering type female connector Accessories: Dust-proof cap, PCS-( )C( ) Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others Part No. PCS-E20MD+ A 33.4 B 27.4 C 11.43 15.8 D E 21.6 PCS-E28MD+ 38.5 32.5 16.51 20.88 26.7 PCS-E36MD+ 43.6 37.6 21.59 25.96 31.8 PCS-E50MD+ 52.5 46.5 30.48 34.85 40.7 PCS-E68MD+ 63.9 57.9 41.91 46.28 52.1 1.27 mm pitch connector Right-angle through hole type male connector for PCB PCS-E( )LMD+ For PCB Right-angle Through hole Configuration of product Part No. PCS-E ( ) LMD+ Series name No. of contacts: 20, 28, 36, 50, 68, 80 or 96 Type of connector LMD: Right-angle through hole type, male LAST POS. + B 0.1 LAST POS. 5.705 Board-edge 1.9050.053 - Except 50-contact connector 2-o2.8 + POS.#2 POS.#1 1.27 0.05 - + o0.8 0.06 - + C 0.1 - Recommended PCB layout (Connector side) A B C t = 1.6 mm 3.6 2.0 E 0.8 4 oe0.4 1.9053 0.85 2.8 5.905 0.85 15 17.0 5.5 4.0 2.54 4-R1 LAST POS. D 3.4 7.0 10.5 5.7 POS.#2 0.8 2-M2.50.45 8.47 1.27 2.0 4.37 POS.#1 2-M2.50.45 1.27 C F B POS.#2 POS.#1 LAST POS. LAST POS. Components Shell Insulator Contacts Bracket Except 50-contact connector Dimensions Part No. PCS-E20LMD+ A 33.4 B 27.4 C 11.43 D 15.8 E 21.6 F 20.23 PCS-E28LMD+ 38.5 32.5 16.51 20.88 26.7 25.31 PCS-E36LMD+ 43.6 37.6 21.59 25.96 31.8 30.39 PCS-E50LMD+ 52.5 46.5 30.48 34.85 40.7 39.28 PCS-E68LMD+ 63.9 57.9 41.91 46.28 52.1 50.71 PCS-E80LMD+ 71.5 65.5 49.53 53.9 59.7 58.33 PCS-E96LMD+ 81.7 75.69 59.69 64.06 69.9 68.49 Mating connectors: PCS-E series cable-side IDC type female connector PCS-E series cable-side soldering type female connector Accessories: Dust-proof cap, PCS-( )C( ) Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole 1.27 mm pitch connector IDC type female connector for cable PCS-E( )F( ) For cable IDC (1.2 mm) Configuration of product Part No. PCS-E ( ) F ( ) Series name No. of contacts: 20, 28, 36, 50, 68, 80 or 96 Type of contact: Female Cable sizes for reference purposes (In case the cable sheath is made of PVC resin) Blank : AWG#28(7 / 0.127) or AWG#30(1 / 0.254). Outside diameter of insulation is 0.8-1.0 mm. For discrete wire. A : AWG#28(7 / 0.127) or AWG#30(1 / 0.254). Outside diameter of insuration is 0.5-0.65 mm. For discrete wire. B : AWG#30(7 / 0.1). Outside diameter of wire is 0.5-0.65 mm. For discrete wire. C : AWG#28(7 / 0.127) For flat cable D : AWG#30(7 / 0.1) For flat cable (See Note #1) A B POS.#1 5.5 LAST POS. 7.3 POS.#2 2.54 1.27 15 C 13.2 5 1.27 B LAST POS. Note 1: This 96-contact connector is not available for flat cable. POS.#2 POS.#1 Cable cover for discrete wire Components Contacts Spacer Shell Insulator Cable cover Cable cover for flat cable Because some combinations of "Configurations of Product Part No.", are under consideration for development, please contact us for availability details. Mating connectors: PCS-E series through hole type male connector for PCB PCS-E series IDC type male connector for panel Tool: (Refer to page Tool-11) Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others Dimensions Part No. A B PCS-E20F( ) 21.65 11.43 C 15.4 PCS-E28F( ) 26.7 16.51 20.48 PCS-E36F( ) 31.8 21.59 25.56 PCS-E50F( ) 40.7 30.48 34.45 PCS-E68F( ) 52.1 41.91 45.88 PCS-E80F( ) 59.7 49.53 53.5 PCS-E96F( ) 69.9 59.69 63.66 1.27 mm pitch connector Soldering type female connector for cable PCS-E( )FS+ For cable Soldering Configuration of product Part No. PCS-E ( ) FS+ Series name No. of contacts: 20, 28, 36, 50 or 68 Type of contact: Soldering type, female Cable sizes for reference purposes FS: AWG#20 MAX. A B 1.27 5.5 7.3 POS.#1 2.54 POS.#2 15 LAST POS. C 6 13.7 5 B 1.27 LAST POS. Dimensions Part No. A B C PCS-E20FS+ 21.65 11.43 15.4 Contacts Insulator PCS-E28FS+ 26.7 16.51 20.48 PCS-E36FS+ 31.8 21.59 25.56 Shell Spacer PCS-E50FS+ 40.7 30.48 34.45 PCS-E68FS+ 52.1 41.91 45.88 Components POS.#2 POS.#1 Mating connectors: PCS-E series through hole type male connector for PCB PCS-E series IDC type male connector for panel Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole 1.27 mm pitch connector IDC type male connector for panel PCS-E( )PM( )-( ) For cable IDC (1.27 mm) Configuration of product Part No. PCS-E ( ) P M ( )- ( ) Series name No. of contacts: 20, 28, 36, 50 or 68 For panel Type of contact: Male Cable sizes for reference purposes (In case the cable insulation is made of PVC resin) Blank: AWG#28(7 / 0.127). AWG#30(1 / 0.245). For flat cables A : AWG#28(7 / 0.127). AWG#30(1 / 0.245). Outside diameter of insulation is 0.8-1.0 mm. For discrete wire. B : AWG#30(7 / 0.1). For flat cables. C : AWG#28(7 / 0.127) flat cable. AWG#30(1 / 0.245). Outside diameter of insulation is 0.5-0.65 mm. For discrete wire. D : AWG#30(7 / 0.1). Outside diameter of wire is 0.5-0.65 mm. For discrete wire. Holes on mounting flange Blank: M2.50.45 H : Diameter of hole: 2.7 mm (The connector is mounted on the Die-cast material vertical backshell of PCS-E( )PML( ).) 15.6 10.5 5.5 5.7 2.45 POS.#1 F D 0.85 1.27 1.27 E D 15 C B 0.85 4-R1 A 3.6 4 For discrete wire For flat cable Holes on mounting flange LAST POS. This figure shows 36-contact connector as a typical example. Dimensions Components Insulator Shell Contacts Spacer Because some combinations of "Configurations of Product Part No.", are under consideration for development, please contact us for availability details. Cable cover Mating connectors: PCS-E series cable-side soldering type female connector PCS-E series cable-side IDC type female connector Accessories: Dust-proof cap, PCS-E( )C( ) Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others Part No. PCS-E20PM( ) A 33.4 B 27.4 C 15.8 D 11.43 E 21.6 F 21.65 PCS-E28PM( ) 38.5 32.5 20.88 16.51 26.7 26.7 PCS-E36PM( ),-H 43.6 37.6 25.96 21.59 31.8 31.8 PCS-E50PM( ) 52.5 46.5 34.85 30.48 40.7 40.7 PCS-E68PM( ) 63.9 57.9 46.28 41.91 52.1 52.1 1.27 mm pitch connector IDC type male connector for cable PCS-D( )( )MA1( )+ For cable IDC (0.635 mm) Daisy chain Configuration of product Part No. PCS-D ( ) ( ) M A 1 ( )+ Series name No. of contacts: 50 or 68 Strain relief Blank: Not provided R : Provided Type of contact: Male Cable size A: AWG#30 (7 / 0.1) For flat cable Contact plating Blank: Min. 0.2 m Gold plating G1 : Min. 0.76 m Gold plating A B POS.#1 5.69 2.54 1.27 7.3 POS.#2 4-R1.04 LAST POS. 15 IDC direction 2.0 C D 0.635 E 2.5 8.65 5.1 LAST POS. POS.#1 POS.#2 Components Contacts Insulator Dimensions Cable housing A Cable housing B Strain relief Because some combinations of "Configurations of Product Part No.", are under consideration for development, please contact us for availability details. Part No. A PCS-D50( )MA1( )+ 40.13 PCS-D68( )MA1( )+ 51.56 B 30.48 C 34.85 D 36.8 E 31.115 41.91 46.28 48.23 42.545 Mating connectors: PCS series straight through hole type female connector for PCB PCS-XE series through hole type female connector for PCB Required tools: MLPT-0003A (68 contacts) and MLPT-0003B (50 contacts) locators Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole 1.27 mm pitch connector IDC type female connector for cable PCS-D68( )FA1( )+ For cable IDC (0.635 mm) Daisy chain Configuration of product Part No. PCS-D 68 ( ) F A 1 ( )+ Series name No. of contacts: 68 Strain relief Blank: Not provided R : Provided Type of contact: Female Cable sizes A: AWG#30 (7 / 0.1) For flat cable Contact plating Blank: Min. 0.2 m Gold plating G1 : Min. 0.76 m Gold plating 51.56 41.91 1.27 POS.#2 POS.#1 7.3 5.54 2.54 LAST POS. 15 4-R1 IDC direction 5 2.0 46.13 2.5 8.25 0.635 42.545 LAST POS. Components Contacts Insulator POS.#2 POS.#1 Cable housing A Cable housing B Strain relief Mating connectors: PCS series through hole type male connector for PCB Required tools: Locator, MLPT-0006A (only for 68 contacts) Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others 1.27 mm pitch connector Straight through hole type female connector for PCB PCS-XE( )SFD( )( )+ For PCB Straight Through hole SCSI-II Configuration of product Part No. PCS-XE ( ) S FD ( ) ( )+ Series name No. of contacts: 26, 50 or 68 Type of shell S: Short shell Type of connector FD: Straight through hole type, female Screw size Blank: M2.50.45 (standard) U : #4-40UNC U2 : #2-56UNC Contact plating Blank: Min. 0.2 m Gold plating G1 : Min. 0.76 m Gold plating A B C POS.#2 Note 1: This 26-contact connector is not available for #4-40UNC and #2-56UNC screws. POS.#1 5.54 7 8.2 2.54 1.27 15 LAST POS. D Screw size 4-R1 E 5.4 9.3 REF. 5.5 1.5 0.85 * 1.27 3.4 3.8 0.350.4 C F 1.9053 * * + B 0.1 + C 0.1 + 1.27 0.05 POS.#2 - LAST POS. - + -0.1 oG - HONDA * * LAST POS. + o0.8 0.06 POS.#1 1.9050.053 JAPAN LAST POS. - POS.#2 For 68-contact connector LAST POS. For 68-contact connector Recommended PCB layout (Connector side) t = 1.6 mm Dimensions Components Shell A Shell B Insulator Contacts POS.#1 Part No. PCS-XE26SFD( )( )+ A B D 19.46 F 31.2 C 15.24 E 37.2 27.05 20.0 PCS-XE50SFD( )( )+ 52.5 46.5 30.48 34.7 42.29 35.24 PCS-XE68SFD( )( )+ 63.9 57.9 41.91 46.13 53.72 46.67 Because some combinations of "Configurations of Product Part No.", are under consideration for development, please contact us for availability details. Part No. PCS-XE( )SFD( )+ Screws size M2.50.45 oG 2.8 PCS-XE( )SFDU( )+ #4-40UNC 3.05 PCS-XE( )SFDU2( )+ #2-56UNC 2.5 Mating connectors: PCS-XE series IDC type male connector for cable Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole 1.27 mm pitch connector Straight through hole type female connector for PCB PCS-XE( )SFD( )N( )+ For PCB Straight Through hole SCSI-III Configuration of product Part No. PCS-XE ( ) S FD ( ) N ( )+ Series name No. of contacts: 50, 68 or 100 Type of shell S: Short shell Type of connector FD: Straight through hole type, female A B C Note 1: This 26-contact connector is not available for #4-40UNC and #2-56UNC screws. 2.54 1.27 POS.#2 POS.#1 5.54 8.2 Screw size Blank: M2.50.45 U : #4-40UNC (standard) U2 : #2-56UNC Lock type N: Screw lock Contact plati ating plating Blank: Min Min.. 0.2 m Gold plating G1 : Min. Min. 0.76 m Gold d plating Screw size 15 LAST POS. D 4-R1 5.4 3.4 3.8 9.2 REF. 1.27 * * 0.350.4 C E 1.9053 * * + B 0.1 + C 0.1 + 1.27 0.05 POS.#2 - LAST POS. - - + -0.1 POS.#1 5.0 HONDA JAPAN oG * * POS.#2 POS.#1 F 1.9050.053 LAST POS. + o0.8 0.06 - LAST POS. LAST POS. For 68 or 100-contact connectors For 68 or 100-contact connectors Dimensions Part No. PCS-XE50SFD( )N( )+ A 52.5 Shell A PCS-XE68SFD( )N( )+ Shell B PCS-XE100SFD( )N( )+ Components Insulator Contacts B 46.5 C 30.48 D 34.7 E 35.24 63.9 57.9 41.91 46.13 46.67 53.5 84.3 78.23 62.23 66.45 66.99 73.85 SMT F 42.1 Because some combinations of "Configurations of Product Part No.", are under consideration for development, please contact us for availability details. Mating connectors: PCS-XE series IDC type male connector Through hole Recommended PCB layout (Connector side) Press-in IDC Wire Soldering Crimping wrapping Others t = 1.6 mm Part No. PCS-XE( )SFDN( )+ Screws size M2.50.45 oG 2.8 PCS-XE( )SFDUN( )+ #4-40UNC 3.05 PCS-XE( )SFDU2N( )+ #2-56UNC 2.5 1.27 mm pitch connector Right-angle through hole type female connector for PCB PCS-XE( )LFD( )( )+ For PCB Right-angle Through hole SCSI-II Configuration of product Part No. PCS-XE ( ) LFD ( ) ( )+ Series name Contact plating No. of contacts: 50 or 68 Blank: Min. 0.2 m Gold plating Type of connector G1 : Min. 0.76 m Gold plating LFD: Right-angle through hole type, female Screw size Blank: M2.50.45 (standard) U : #4-40UNC U2 : #2-56UNC TM A B 3.6 2 4.37 0.8 LAST POS. Screws size 1.9053 o0.80.06 LAST POS. oG0.1 5.705 REF. 4.0 15 D 3.4 2.54 2 7 8.47 1.27 10.5 5.5 4-R1 POS.#1 C POS.#2 E 1.27 LAST POS. Screws size POS.#2 Shell B Insulator Contacts 3 0.05 POS.#1 POS.#1 POS.#2 For 68-contact connector Dimensions A Part No. PCS-XE50( )LFD( )( )+ 52.5 PCS-XE68( )LFD( )( )+ 63.9 1.905 POS.#1 POS.#2 For 68-contact Recommended PCB layout connector (Connector side) t = 1.6 mm B Bracket Shell A 1.270.05 C0.1 B0.1 C F Components POS.#2 POS.#1 2.8 5.4 5.905 5.5 17 1.5 0.85 B 46.5 C 30.48 D 34.7 E 42.29 F 39.28 57.9 41.91 46.13 53.72 50.71 Part No. PCS-XE( )LFD( )+ Screws size M2.50.45 PCS-XE( )LFDU( )+ #4-40UNC PCS-XE( )LFDU2( )+ #2-56UNC oG 2.8 3.05 2.5 Because some combinations of "Configurations of Product Part No.", are under consideration for development, please contact us for availability details. Mating connectors: PCS-XE series IDC type male connector for cable Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole 1.27 mm pitch connector Right-angle through hole type female connector for PCB PCS-XE68LFDT( )N( )+ For PCB Right-angle Through hole SCSI-III Configuration of product Part No. PCS-XE 68 LFD T ( ) N ( )+ Series name Screw size No. of contacts: 68 Blank: M2.50.45 Type of connector U : #4-40UNC (standard) LFD: Right-angle through hole type, U2 : #2-56UNC female Lock type Board lock pin N: Screw lock Blank: None Contact plating T : Provided Blank: Min. 0.2 m Gold plating G1 : Min. 0.76 m Gold plating TM A 3.6 0.8 Screw size 0.8 4 2.8 5.905 5.4 16.9 5.705 REF. POS.#1 1.9053 B0.1 LAST POS. Board-edge POS.#1 LAST POS. 1.27 POS.#2 oF0.1 C E POS.#2 B Recommended PCB layout (Connector side) t = 1.6 mm Part No. PCS-XE68LFDTN( )+ Dimensions Shell B Insulator Part No. PCS-XE68LFDT( )N( )+ Board lock Contacts A 63.9 B 57.9 SMT C 41.91 D 46.13 E 50.71 Press-in IDC Wire Soldering Crimping wrapping Others oF Screws size M2.50.45 2.8 PCS-XE68LFDTUN( )+ #4-40UNC 3.05 PCS-XE68LFDTU2N( )+ #2-56UNC 2.5 Because some combinations of "Configurations of Product Part No.", are under consideration for development, please contact us for availability details. Mating connectors: PCS-XE series IDC type male connector for cable Through hole o0.80.06 0.05 1.27 C0.1 Components Bracket pin Shell A 3 4-R1 D 2.85 3.4 15 8.47 10.5 LAST POS. 0.05 POS.#2 4.37 2.0 5.5 2.54 1.27 POS.#1 1.905 B C 1.27 mm pitch connector Right-angle through hole type female connector for PCB PCS-XE100LFD( )-( )+ For PCB Right-angle Through hole Screw lock Configuration of product Part No. PCS-XE 100 LFD ( )- ( )+ Series name Screw sizes for lock screws No. of contacts: 100 HS : #4-40UNC (standard) Type of connector HSU2 : #2-56UNC LFD: Right-angle through hole type, female Contact plating Blank: Min. 0.2 m Gold plating G1 : Min. 0.76 m Gold plating Panel (Panel thickness: 1.6 mm) 1.27 POS.#1 4.05 4.6 POS.#2 LAST POS. 4.8 1.9053 16.9 6.705 1.6 3.9 Panel thickness 5.4 66.45 78.23 3.17 8.74 5.5 2.54 86.0 1.2749=62.23 1.27 POS.#2 POS.#1 12749=62.23 78.23 5.5 6.405MAX. #4-40UNC LAST POS. 6.4 REF. + o0.8 0.06 LAST POS. - 3.7 2-o3.05 POS.#1 POS.#2 M30.5 1.9050.053 Screw size + 1.27 0.05 1.2749=62.230.1 - + 78.23 0.1 - Components Bracket Ground plate Recommended PCB layout (Connector side) t = 1.6 mm Shell Insulator Contacts Lock screws Because some combinations of "Configurations of Product Part No.", are under consideration for development, please contact us for availability details. Part No. PCS-XE100LFD( )-HS+ PCS-XE100LFD( )-HSU2+ Screws size #4-40UNC #2-56UNC Mating connectors: PCS-XE series IDC type male connector for cable Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole 1.27 mm pitch connector Right-angle through hole type female connector for PCB PCS-XE( )SLFD( )( )+ For PCB Right-angle Through hole SCSI-II Configuration of product Part No. PCS-XE ( ) S LFD ( ) ( )+ Series name Screw size No. of contacts: 26, 50 or 68 Blank: M2.50.45 (standard) Type of shell U : #4-40UNC S: Short shell U2 : #2-56UNC Type of connector Contact plating LFD: Right-angle through hole type, Blank: Min. 0.2 m Gold plating female G1 : Min. 0.76 m Gold plating HONDA JAPAN A B C 1 50 26 3.2 0.5 4-R1 0.40.35 LAST POS. 15 D 2.0 4.37 7.0 8.2 5.54 25 8.47 Screw size POS.#2 0.8 4.0 3.4 2.54 1.27 POS.#1 1.9053 E Screw size LAST POS. 1.27 POS.#2 POS.#1 C F B oG POS.#2 POS.#1 POS.#1 Components Part No. PCS-XE26SLFD( )( )+ A 37.2 B 31.2 C 15.24 Insulator Shell B PCS-XE50SLFD( )( )+ 52.5 46.5 PCS-XE68SLFD( )( )+ 63.9 57.9 SMT LAST POS. + + 1.27 0.05+0.1 C o0.8 0.06 - - - D 19.46 E 27.05 24.05 Part No. PCS-XE( )SLFD( )+ Screws size M2.50.45 oG 2.8 30.48 34.7 42.29 39.28 PCS-XE( )SLFDU( )+ #4-40UNC 3.05 41.91 46.13 53.72 50.71 PCS-XE( )SLFDU2( )+ #2-56UNC 2.5 F Because some combinations of "Configurations of Product Part No.", are under consideration for development, please contact us for availability details. Mating connectors: PCS-XE series IDC type male connector for cable Through hole Board-edge t = 1.6 mm Dimensions Bracket Shell A Contacts - Recommended PCB layout (Connector side) POS.#2 For 68-contact connector + B 0.1 1.9050.053 2.8 5.705 REF. POS.#1 POS.#2 For 68-contact connector 5.4 17.0 5.905 5.5 1.5 0.85 Press-in IDC Wire Soldering Crimping wrapping Others 1.27 mm pitch connector Right-angle through hole type female connector for PCB PCS-XE( )SLFDT( )( )+ For PCB Right-angle Through hole SCSI-II Configuration of product Part No. PCS-XE ( ) S LFD T ( ) ( )+ Series name Screw size No. of contacts: 26, 50 or 68 Blank: M2.50.45 (standard) Type of shell U : #4-40UNC S: Short shell U2 : #2-56UNC Type of connector Contact plating LFD: Right-angle through hole type, Blank: Min. 0.2 m Gold plating female G1 : Min. 0.76 m Gold plating Board lock pin: Provided Screw size LAST POS. 15 D 0.5 3.4 2.85 4-R1 0.40.35 0.8 2.8 0.85 5.4 17.0 5.905 5.5 1.5 E LAST POS. POS.#1 POS.#2 For 68-contact connector + B 0.1 Board-edge - LAST POS. POS.#1 POS.#2 1.27 1.9053 4 + oG 0.05 POS.#2 POS.#1 - C F B POS.#1 POS.#2 For 68-contact connector + 1.27 0.05+0.1 C Insulator Shell A Contacts Board lock pin + - o0.8 0.06 - - Recommended PCB layout (Connector side) Components Bracket Shell B 1.9050.053 26 3.3 4.37 50 7.0 1 8.2 25 8.47 POS.#1 5.705 REF. 5.54 2.54 1.27 A B C POS.#2 t = 1.6 mm Dimensions Part No. PCS-XE26SLFDT( )( )+ A 37.2 B 31.2 C 15.24 PCS-XE50SLFDT( )( )+ 52.5 46.5 PCS-XE68SLFDT( )( )+ 63.9 57.9 D 19.46 E 27.05 24.05 F Part No. PCS-XE( )SLFDT( )+ Screws size M2.50.45 oG 2.8 30.48 34.7 42.29 39.28 PCS-XE( )SLFDTU( )+ #4-40UNC 3.05 41.91 46.13 53.72 50.71 PCS-XE( )SLFDTU2( )+ #2-56UNC 2.5 Because some combinations of "Configurations of Product Part No.", are under consideration for development, please contact us for availability details. Mating connectors: PCS-XE series IDC type male connector for cable Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole 1.27 mm pitch connector Right-angle through hole type female connector for PCB PCS-XE( )SLFD( )N( )+ For PCB Right-angle Through hole SCSI-III Configuration of product Part No. PCS-XE ( ) S LFD ( ) N ( )+ Series name Screw size No. of contacts: 50 or 68 Blank: M2.50.45 Type of shell U : #4-40UNC (standard) S: Short shell U2 : #2-56UNC Type of connector Lock type LFD: Right-angle through hole type, N: Screw lock female Contact pla ating plating Blank: Min n. 0.2 m Gold d plating Min. G1 : Min Go plating Min.. 0.76 m Gold HONDA JAPAN 3.2 0.8 4 1.9053 4-R1 15 POS.#1 POS.#2 For 68-contact connector 16.9 5.905 5.4 2.8 D 5.705 REF. LAST POS. 3.4 2.0 4.37 0.5 0.40.35 + B 0.1 Board-edge - 1.9050.053 Screw size POS.#2 8.2 5.54 2.54 1.27 POS.#1 8.47 A B C LAST POS. Screw size LAST POS. 1.27 POS.#2 POS.#1 C E B oF POS.#2 POS.#1 POS.#1 A 52.5 B 46.5 C 30.48 D 34.7 E 39.28 Insulator Shell A PCS-XE68SLFD( )N( )+ 63.9 57.9 41.91 46.13 50.71 Because some combinations of "Configurations of Product Part No.", are under consideration for development, please contact us for availability details. Mating connectors: PCS-XE series IDC type male connector for cable SMT - Dimensions Part No. PCS-XE50SLFD( )N( )+ Through hole + o0.8 0.06 - t = 1.6 mm Bracket Shell B Contacts - Recommended PCB layout (Connector side) POS.#2 For 68-contact connector Components + 1.27 0.05 +0.1 C Press-in IDC Wire Soldering Crimping wrapping Others Part No. PCS-XE( )SLFDN( )+ PCS-XE( )SLFDUN( )+ Screws size M2.50.45 #4-40UNC PCS-XE( )SLFDU2N( )+ #2-56UNC oF 2.8 3.05 2.5 1.27 mm pitch connector Right-angle through hole type female connector for PCB PCS-XE( )SLFDT( )N( )+ For PCB Right-angle Through hole SCSI-III Configuration of product Part No. PCS-XE ( ) S LFD T ( ) N ( )+ Series name Screw size No. of contacts: 50 or 68 Blank: M2.50.45 Type of shell U : #4-40UNC (standard) S: Short shell U2 : #2-56UNC Type of connector Lock type LFD: Right-angle through hole type, N: Screw lock female Contact plat ing plating Board lock pin: Provided Blank: Min. 0.2 0 m Gol ld plating Gold G1 : Min. 0.76 0 m Go old plating Gold HONDA JAPAN 0.8 4 POS.#2 1.9053 POS.#1 POS.#2 For 68-contact connector + B 0.1 Board-edge 5.705 REF. 2.8 1.27 3.4 - LAST POS. POS.#1 C E B + oF 0.1 POS.#2 POS.#1 - POS.#1 + 1.27 0.05 + C 0.1 - Contacts Board lock pin - t = 1.6 mm Components Insulator Shell A + o0.8 0.06 - Recommended PCB layout (Connector side) POS.#2 For 68-contact connector Bracket Shell B 1.9050.053 D 4.37 0.5 LAST POS. 15 16.9 5.905 5.4 2.85 3.2 4-R1 0.40.35 LAST POS. Screw size POS.#2 8.47 1.27 POS.#1 8.2 5.54 2.54 A B C Dimensions Part No. PCS-XE50SLFDT( )N( )+ A 52.5 B 46.5 C 30.48 D 34.70 E 39.28 PCS-XE68SLFDT( )N( )+ 63.9 57.9 41.91 46.13 50.71 Part No. PCS-XE( )SLFDTN( )+ PCS-XE( )SLFDTUN( )+ Because some combinations of "Configurations of Product Part No.", are under PCS-XE( )SLFDTU2N( )+ consideration for development, please contact us for availability details. Screws size M2.50.45 oF 2.8 #4-40UNC 3.05 #2-56UNC 2.5 Mating connectors: PCS-XE series IDC type male connector for cable Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole 1.27 mm pitch connector Right-angle SMT type female connector for PCB PCS-XE( )SLFYTU( )+ For PCB Right-angle SMT SCSI-II Configuration of product Part No. PCS-XE ( ) S LFY T U ( )+ Series name No. of contacts: 26 or 50 Type of shell S: Short shell Type of connector LFY: Right-angle SMT type, female Board lock pin: Provided Screw size U: #4-40UNC Contact plating Blank: Min. 0.2 m Gold plating G1 : Min. 0.76 m Gold plating 3.2 POS.#2 4-R1 POS.#1 1 7 8.57 5.54 4.37 11.92 Screw size 13 26 14 D 15 E LAST POS. 0.8 B0.1 E0.1 F Board-edge 6.7 + - 4 0.05 5.705 4.05 18.6 o1.5 4.25 5.905 5.4 0.85 5.5 1.5 0.85 + 2-o4.5 0.05 - Components Contacts Bracket Shell A Shell B Insulator Snap lock Snap pin + SMT - + - - 0.6 REF. Because some combinations of "Configurations of Product Part No.", are under consideration for development, please contact us for availability details. Press-in IDC 0.635 0.05 + G 0.05 H0.1 POS.#(contacts/2+1) Recommended PCB layout Dimensions Part No. PCS-XE26SLFYTU( )+ A 42.0 B 31.2 C 15.24 D 19.46 E 20.93 F 27.05 G 7.62 H 15.875 PCS-XE50SLFYTU( )+ 57.24 46.5 30.48 34.7 36.17 42.29 15.24 31.115 Mating connectors: PCS-XE series IDC type male connector for cable Through hole 2-o1.7 0.1 POS.#1 2 LAST POS. POS. #2 0.635 G H B +0.05 1.27 - A B C 0.5 3.1 Wire Soldering Crimping wrapping Others 1.27 mm pitch connector Straight Press-in type female connector for PCB PCS-XE50SFP( )( ) For PCB Straight Press-in SCSI-II Configuration of product Part No. PCS-XE 50 SFP ( ) ( ) Series name No. of contacts: 50 Type of connector SFP: Straight Press-in type, female Screw size Blank: M2.50.45 (standard) U : #4-40UNC U2 : #2-56UNC Contact plating G1: Min. 0.76 m Gold plating 52.5 46.5 30.48 1.27 POS.#1 POS.#2 7 5.54 10 2.54 4-R1 15 LAST POS. 34.7 42.29 5 1.5 0.85 8.3 4.8 13.4 REF. 5.1 1.9053 1.27 30.48 + 46.5 0.1 - LAST POS. + 30.48 0.1 - +0.05 -0.076 o0.71 POS.#1 POS.#2 + 1.27 0.05 - Components Small flat head Insulator A screw LAST POS. Recommended PCB layout (Connector side) POS.#2 POS.#1 + t = 2.4 0.2 mm Dimensions Shell A Shell B Insulator B Contacts Hex. nuts 1.9050.053 oF Part No. PCS-XE50SFP( ) Because some combinations of "Configurations of Product Part No.", are under consideration for development, please contact us for availability details. Screws size M2.50.45 oF 2.8 PCS-XE50SFPU( ) #4-40UNC 3.05 PCS-XE50SFPU2( ) #2-56UNC 2.5 Mating connectors: PCS-XE series IDC type male connector for cable Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole 1.27 mm pitch connector IDC type male connector for cable PCS-XE( )M( )( )+ For cable IDC (1.27 mm) SCSI-II, SCSI-III Configuration of product Part No. PCS-XE ( ) M ( ) ( )+ Series name No. of contacts: 26, 50, 68 or 100 Type of contact: Male Cable sizes for reference purposes (In case the cable insulation is made of PVC resin) Blank : AWG#28(7 / 0.127) or AWG#30(1 / 0.254). Outside diameter of insulation is 0.8-1.0 mm. For discrete wire. (See Note #1) A : AWG#28(7 / 0.127) or AWG#30(1 / 0.254). Outside diameter of insulation is 0.5-0.65 mm. For discrete wire. B : AWG#30(7 / 0.1). Outside diameter of insulation is 0.5-0.65 mm. For discrete wire. C : AWG#28(7 / 0.127) or AWG#30(1 / 0.254). For flat cable, t = 1.0 mm MAX. (See Note #2) E : AWG#30(7 / 0.1). For flat cable, t = 1.0 mm MAX. (See Note #2) J : AWG#28(7 / 0.127) or AWG#30(1 / 0.254). Outside diameter of insulation is 0.65-0.8 mm. For discrete wire. K : AWG#30(7 / 0.1). Outside diameter of insulation is 0.65-0.8 mm. For discrete wire. Q : AWG#30(7 / 0.1). Outside diameter of insulation is 0.8-1.0 mm. For discrete wire. Contact plating Blank : Min. 0.2 m Gold plating G1 : Min. 0.76 m Gold plating POS.#2 POS.#1 A .0 R1 1.27 4- 7.3 5.7 2.54 D 4 B Cable cover for discrete wire LAST POS. 15 C Cable cover for flat cable 13.2 5 1.27 B For 68 or 100-contact connector LAST POS. Components Contacts Shell Insulator Spacer Cable cover Dimensions POS.#1 POS.#2 Part No. PCS-XE26M( )( )+ Because some combinations of "Configurations of Product Part No.", are under consideration for development, please contact us for availability details. Mating connectors: PCS-XE series straight or right-angle through hole type female connector for PCB. PCS-XE series SMT type female connector. For use with housings: SCSI-II: PCS-E( )L( ). SCSI-III: PCS-XEM( )DL( )( )N Required tools: Discrete wire tool: PCS-K1 or FHAT-918B and FHPT-918A. Flat cable tool: PCS-K4 Through hole SMT Press-in IDC Note 1: P/N PCS-XE100M+ is not available. Note 2: This 100-contact connector is not available for flat cable. (C, E) Wire Soldering Crimping wrapping Others A 25.46 B 15.24 C 19.61 D 25.46 PCS-XE50M( )( )+ 40.7 30.48 34.85 40.7 PCS-XE68M( )( )+ 52.13 41.91 46.28 52.1 PCS-XE100M( )( )+ 72.45 62.23 66.6 72.4 1.27 mm pitch connector Soldering type male connector for cable PCS-XES68MS+ For cable Soldering SCSI-III Configuration of product Part No. PCS-XES 68 MS+ Series name No. of contacts: 68 Type of connector MS: Soldering type, male 49.88 1.27(34-1)=41.91 1.27 POS.#2 2.54 9.8 5.7 POS.#1 4-R1.04 LAST POS. 15 46.28 11.5 3.05 3.05 17.6 REF. 5 1.27 1.27(34-1)=41.91 LAST POS. Components Shell POS.#1 POS.#2 Insulator Contacts Mating connectors: PCS-XE series straight or right-angle through hole type female connector for PCB, PCS-XE series SMT type female connector for PCB, PCS-XE series of IDC type female connectors for cable panel For use with housings: PCS-SE68LDAU2N Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole 1.27 mm pitch connector IDC type female connector for panel PCS-XE( )SPF( )( )( ) For cable IDC (1.27 mm) SCSI-II Configuration of product Part No. PCS-XE ( ) S P F ( ) ( ) ( ) Series name B : AWG#30(7 / 0.1). Outside No. of contacts: 26, 50 or 68 diameter of insulation is 0.5-0.65mm. For discrete wire. Type of shell C : AWG#28(7 / 0.127) or AWG#30 S: Short shell (1 / 0.254). For flat cable, Panel t = 1.0 mm. P: Panel mounting E : AWG#30(1 / 0.1). For flat cable, Type of contact t = 1.0 mm. F: IDC type, female Screw size Cable sizes for reference purposes (In case the cable insulation is made of Blank : M2.50.54 (standard) PVC resin) U : #4-40UNC Blank : AWG#28(7 / 0.127) or AWG#30(1 / U2 : #2-56UNC 0.254). Outside diameter of insulation Contact plating is 0.8-1.0 mm. For discrete wire. Blank : Min. 0.2 m Gold plating A : AWG#28(7 / 0.127) or AWG#30(1 / G1 : Min. 0.76 m Gold plating 0.254). Outside diameter of insulation is 0.5-0.65 mm. For discrete wire. A 4-R1 B C POS.#1 7 10.5 POS.#2 5.54 2.54 1.27 15 LAST POS. Screw size D E F 5.4 13.2 4.4 5.5 1.5 0.85 Cable cover for discrete wire 1.27 Cable cover for flat cable C LAST POS. For 68-contact connector Note 1: This 26-contact connector is not available for screw size, #4-40UNC or #2-56UNC. Components Insulator Shell POS.#2 POS.#1 Bracket Spacer Contacts Cable cover Because some combinations of "Configurations of Product Part No.", are under consideration for development, please contact us for availability details. Dimensions A Part No. PCS-XE26SPF( )( )( ) 37.2 B F C D E 31.2 15.24 19.46 27.05 25.46 PCS-XE50SPF( )( )( ) 52.5 PCS-XE68SPF( )( )( ) 63.9 46.5 30.48 34.7 42.29 40.7 57.9 41.91 46.13 53.72 52.1 Mating connectors: PCS-XE series IDC type male connector for cable Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole 1.27 mm pitch connector IDC type female connector for panel PCS-XED( )( )FA( )( )+ For cable IDC (0.635 mm) SCSI-II Configuration of product Part No. PCS-XED ( ) ( ) F A ( ) ( )+ Series name No. of contacts: 50 or 68 Strain relief Blank: Not provided R : Provided Type of contact F: Female Cable size A: AWG#30(7 / 0.1) For flat cable Screw size Blank: M2.50.54 (standard) U : #4-40UNC U2 : #2-56UNC Contact plating Blank: Min. 0.2 m Gold plating G1 : Min. 0.76 m Gold plating Dimmensions Part No. PCS-XED50( )FA( )( ) A 52.5 B C D E F G H J 46.5 30.48 34.7 42.29 31.115 42.1 37.79 39.49 PCS-XED68( )FA( )( ) 63.9 57.9 41.91 46.13 53.72 42.545 53.47 49.22 50.92 A B IDC direction 2.54 1.27 POS.#1 POS.#2 2.0 4-R1 C Screw size 2.5 7.0 8.2 5.54 H LAST POS. POS.# Marking (4 PLCS) 15 D J E 5.4 7.85 5.5 4.99 1.5 0.85 0.635 Terminal-to-conductor connection (In case of the 50-contact connector) Terminal No. 1 Conductor No. 1 26 2 2 3 27 4 24 47 49 48 25 49 50 50 F G Components Contacts Insulator Shell A Shell B Cable housing A Cable housing B Strain relief Because some combinations of "Configurations of Product Part No.", are under consideration for development, please contact us for availability details. Mating connectors: PCS-XE series IDC type male connector for cable Required tools: Locator tool, MLPT-0004A for 68 contacts or MLPT-0004B for 50 contacts Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others Part No. PCS-XED( )( )FA( )+ Screws size M2.50.45 PCS-XED( )( )FAU( )+ #4-40UNC PCS-XED( )( )FAU2( )+ #2-56UNC 1.27 mm pitch connector IDC type female connector for panel PCS-XED68( )FAUN( )+ For cable IDC (0.635 mm) SCSI-III Configuration of product Part No. PCS-XED 68 ( ) F A U N ( )+ Series name No. of contacts: 68 Strain relief Blank: Not provided R : Provided Type of contact F: Female Cable size A: AWG#30(7 / 0.1) For flat cable Screw size U: #4-40UNC Lock type N: Screw lock Contact plating Blank: Min. 0.2 m Gold plating G1 : Min. 0.76 m Gold plating 63.9 57.9 4-R1 Screw size IDC direction 2.0 2.54 1.27(34-1)=41.91 1.27 POS.#1 POS.#2 1 68 35 8.2 5.54 34 49.22 LAST POS. 2.5 15 46.13 50.92 7.85 5.4 4.99 0.635 0.635(68-1)=42.545 53.47 Terminal-to-conductor connection JAPAN HONDA Terminal No. 1 Components Conductor No. 1 35 2 2 3 36 4 33 65 67 66 34 67 68 68 Contacts Insulator Shell B Shell A Cable housing A Cable housing B Strain relief Because some combinations of "Configurations of Product Part No.", are under consideration for development, please contact us for availability details. Mating connectors: PCS-XE series IDC type male connector for cable Required tools: Locator tool, MLPT-0004A for 68 contacts or MLPT-0004B for 50 contacts Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole 1.27 mm pitch connector EMI-filtered vertical type die-cast material backshell for standard cable PCS-E( )L( ) Backshell Vertical EMI-filtered Configuration of product Part No. PCS-E ( ) L ( ) Series name No. of contacts: 20, 28, 36, 50 or 68 Type of backshell L: Vertical type backshell for standard cable Identification mark (A, B or C) of cable-end-outlet dimension. Cable diameters for reference purposes are shown in the Dimension table as below. C B 32 10 A Dimensions Components A B C 65 PCS-E20LB 30.0 20.3 87 o7.5 10.38.5 o4.3 o8.7 o5.5, o5.9 Cover A Cover B PCS-E20LC Latch Small-sized Phillips flat head screw PCS-E28LB Cable clamp Small-sized Phillips head screw PCS-E28LA 35.0 25.3 PCS-E36LA 40.2 30.5 PCS-E50LA 48.9 PCS-E68LA 60.3 For use with connector: PCS-E series IDC type or soldering type female connector for cable PCS-XE series IDC type male connector for cable Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others Outside diameter of cable for reference purposes Part No. PCS-E20LA 6.55 o5.5 9.58.5 o9 9.58 o8.4, o9 39.2 8.57 o7.3, o8 50.6 8.57.5 o8.1 1.27 mm pitch connector Mating guide structure vertical type die-cast material backshell for standard cable PCS-E( )LG( ) Backshell Vertical EMI-filtered Configuration of product Part No. PCS-E ( ) LG ( ) Series name No. of contacts: 28, 36 or 50 Type of backshell LG: Mating guide structure vertical type backshell for standard cable Identification mark (A or B) of cable-end-outlet dimension. Cable diameters for reference purposes are shown in the Dimension table below. E B 10 32 A C 1.5 D Components Dimensions Cover A Cover B A 35.0 B 25.3 C 30 D 16 E 8.59.5 Outside diameter of cable for reference purposes PCS-E28LGB PCS-E36LGA 40.2 30.5 34 31 77.5 o7.5 PCS-E50LGA 48.9 39.2 42 39 78.5 o8 Part No. Latch Cable clamp Small-sized Phillips head screw Small-sized Phillips flat head screw Because some combinations of "Configurations of Product Part No.", are under consideration for development, please contact us for availability details. For use with connector: PCS-E series IDC type or soldering type female connector for cable PCS-XE series IDC type male connector for cable Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others o9 1.27 mm pitch connector Horizontal type die-cast material backshell for standard cable PCS-E( )W Backshell Horizontal EMI-filtered Configuration of product Part No. PCS-E ( ) W Series name No. of contacts: 20, 28, 36 or 50 Type of backshell W: Horizontal type backshell for standard cable 10 25 32 1.5 A Components Dimensions Cover A Cover B Part No. Outside diameter of cable for reference purposes Latch Small-sized Phillips flat head screw PCS-E20W A 30.0 PCS-E28W 35.0 o6 Cable clamp Small-sized Phillips head screw PCS-E36W 40.2 o8.2 PCS-E50W 48.9 o7.8 o5.6 For use with connector: PCS-E series IDC type or soldering type female connector for cable PCS-XE series IDC type male connector for cable Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole 1.27 mm pitch connector Vertical type plastic backshell for flat cable PCS-E( )LT+ Backshell Vertical Configuration of product Part No. PCS-E ( ) LT+ Series name No. of contacts: 28, 36 or 50 Type of backshell LT: Vertical type backshell for flat cable 10 A 20 B C Components Dimensions Cover B Cover A Latch Small-sized Phillips head screw Hex nuts For use with connector: PCS-E series IDC type female connector for cable PCS-XE series IDC type male connector for cable Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others Part No. PCS-E28LT+ A 18.3 B 37.0 C 35.0 PCS-E36LT+ 23.4 42.2 40.2 PCS-E50LT+ 32.2 50.9 48.9 1.27 mm pitch connector Vertical type die-cast material backshell for cable extension PCS-E( )PML( ) Backshell Vertical EMI-filtered Configuration of product Part No. PCS-E ( ) PML ( ) Series name No. of contacts: 36 Type of backshell PML : Vertical type backshell for PCS-E( )PM( )-H Outside diameter of cable for reference purpose A: 9 mm diameter D C 10 27.5 2.5 3 A B Components 2-M2.5 Cover A Cover B Cable clamp Small-sized Phillips head screw Small-sized Phillips flat head Dimensions Part No. PCS-E36PMLA No. of contacts A B C D Outside diameter of cable for reference purposes 36 43.3 37.6 27.3 89.5 o9 For use with connector: PCS-E( )PM( )-H Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole 1.27 mm pitch connector Vertical type die-cast material backshell for standard cable with provision for preventing misinsertion PCS-E( )LP( )-( )+R Backshell Vertical EMI-filtered Configuration of product Part No. PCS-E ( ) LP ( )- ( )+R Series name Identification mark (A, B or C) of No. of contacts: 20, 28, 36, 50 or 68 cable-end-outlet dimension. Type of backshell Cable diameters for reference LP: Vertical type backshell for purposes are shown in the standard cables with provision for Dimension table as shown below. preventing misinsertion Key-riveted position (Refer to the Dimension table as shown below) for preventing misinsertion. C B A 10 C D B 32 1 2 3 4 B A A C 3 B 2 A 1 D E 4 5 C 3 B 2 A 1 For 50-contact backshell 4 D D C 5 B E A For 68-contact backshell Dimensions Components C Outside diameter of cable for reference purposes 65 o5.5 87 o7.5 PCS-E28LPA-( )+R 6.55 o5.5, o5.9 PCS-E28LPB-( )+R 35.0 25.3 108 o9 Small-sized Phillips PCS-E28LPC-( )+R 118 o10 head screw PCS-E36LPA-( )+R 40.2 30.5 PCS-E50LPA-( )+R 48.9 39.2 108 o8.4, o9 108 o7.3 PCS-E68LPA-( )+R 108 o8.1 7.56 o6.5 1 Cover A Cover B 2 3 Part No. PCS-E20LPA-( )+R 4 Key-riveted position No. PCS-E20LPB-( )+R Latch Cable clamp B 2 A 1 C D 3 4 B 2 A 1 B C 2 3 A 1 Key rivet For 28-contact backshell 3 For 20-contact backshell C flat head screw 4 Small-sized Phillips D For 36-contact backshell PCS-E68LPB-( )+R For use with connector: PCS-E series IDC type or soldering type female connector for cable PCS-XE series IDC type male connector for cable Accessories: Key-rivets for preventing misinsertion, PCS-E-PK+R Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others A B 30.0 20.3 60.3 50.6 Key-riveted position No. 1B, 1C, 2A, 3A 1D, 2C, 3B, 4A 1E, 2D, 4B, 5A 1.27 mm pitch connector Vertical type die-cast material backshell for larger diameter cable with provision for preventing misinsertion PCS-E( )LKP( )-( )+R Backshell Vertical EMI-filtered Configuration of product Part No. PCS-E ( ) LKP ( )- ( )+R Series name No. of contacts: 36, 50, 68 or 80 Type of backshell LKP: Vertical type backshell for larger diameter cables with provision for preventing misinsertion Identification mark (A, B or C) of cable-end-outlet dimension. Cable diameters for reference purposes are shown in the Dimension table as shown below. Key-riveted position (Refer to the Dimension table as shown below) for preventing misinsertion. 10 D A B 4 C 5 C D 3 4 A B 1 2 C D 3 4 B 2 A E 5 D E C 3 B B 2 A C A 1 32 For 50,68 and 80-contact backshell 1 For 36-contact backshell Dimensions Components 1 2 3 Cable clamp Small-sized Phillips head screw 4 5 Key-riveted position No. Part No. PCS-E36LKPA-( )+R PCS-E36LKPB-( )+R PCS-E50LKPA-( )+R A C 1011 30.5 40.2 1012 39.2 48.9 1013 50.6 60.3 Latch Cover B PCS-E50LKPC-( )+R Cover A Small-sized Phillips flat head screw PCS-E68LKPB-( )+R Key rivet PCS-E80LKPB-( )+R 1513.6 PCS-E68LKPA-( )+R B PCS-E80LKPA-( )+R 1010 58.2 67.9 D Outside diameter of cable for reference purposes o8 o10.5 Key-riveted position No. 1D, 2C, 3B, 4A o10 11.6 o11.5 o12 o10 1E, 2D, 4B, 5A o9.5 15.0 o13 For use with connector: PCS-E series IDC type or soldering type female connector for cable PCS-XE series IDC type male connector for cable Accessories: Key-rivets for preventing misinsertion, PCS-E-PK+R Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole 1.27 mm pitch connector Vertical type die-cast material backshell for larger diameter cable with mating guide for preventing misinsertion PCS-E96LKP( )-( )+R Backshell Vertical EMI-filtered Configuration of product Part No. PCS-E 96 LKP ( )- ( )+R Series name No. of contacts: 96 Type of backshell LKP: Vertical type backshell for larger diameter cables with provision for preventing misinsertion A 52 Cable Identification mark (A or B) of cable-end-outlet dimension. Cable diameters for reference purposes are shown in the Dimension table as shown below. Key-riveted position (Refer to the Dimension table as shown below) for preventing misinsertion. (The dimensions are shown below.) 11.6 10 C B 36 A 78.1 52 1 2 3 58 4 5 Components 5.2 A E Key-riveted position No. Cover A Cover B Cable clamp Small-sized Phillips head screw Dimensions Latch Small-sized Phillips flat head screw Part No. PCS-E96LKPA-( )+R Key rivet PCS-E96LKPB-( )+R 137.5 For use with connector: PCS-E series IDC type female connector for cable PCS-XE series IDC type male connector for cable Accessories: Key-rivets for preventing misinsertion, PCS-E-PK+R Through hole SMT B D C C D B Press-in IDC Wire Soldering Crimping wrapping E A Others A o10 Outside diameter of cable for reference purposes o10 o7.52 Key-riveted position No. 1E, 2D, 4B, 5A 1.27 mm pitch connector Vertical type die-cast material backshell for larger diameter cable with provision for preventing misinsertion PCS-E96LKP1A-( )+R Backshell Vertical EMI-filtered Configuration of product Part No. PCS-E 96 LKP1 A- ( )+R Series name No. of contacts: 96 Type of backshell LKP1: Vertical type backshell for larger diameter cables with provision for preventing misinsertion Identification mark (A) of cableend-outlet dimension. Cable diameters for reference purposes are shown in the Dimension table as shown below. Key-riveted position (Refer to the Dimension table as shown below) for preventing misinsertion. A 52 11.6 10 C B 36 A 78.1 E 1 2 3 4 5 A Components B D C C D B E A Key-riveted position No. Cover A Cover B Cable clamp Small-sized Phillips head screw Latch Small-sized Phillips flat head screw Key rivet Dimensions Part No. PCS-E96LKP1A-( )+R A 109 Outside diameter of cable for reference purposes o10 Key-riveted position No. 1E, 2D, 4B, 5A For use with connector: PCS-E series IDC type female connector for cable PCS-XE series IDC type male connector for cable Accessories: Key-rivets for preventing misinsertion, PCS-E-PK+R Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole 1.27 mm pitch connector Vertical type die-cast material backshell for standard cable with mating guide for preventing misinsertion PCS-E( )LGP( )-( )+R Backshell Vertical EMI-filtered Configuration of product Part No. PCS-E ( ) LGP ( )- ( )+R Series name Identification mark (A) of cable No. of contacts: 26 or 36 end-outlet dimension. Type of backshell Cable diameters for reference LGP: Vertical type backshell for purposes are shown in the standard cables with mating Dimension table as shown below. guide for preventing misinsertion Key-riveted position (Refer to the Dimension table as shown below) for preventing misinsertion. E B 10 32 1 2 3 4 B A A C D 1 2 3 4 1.5 B C C B D A A D Components Guide position of the 28-contact backshell Cover A Cover B Key-riveted position No. Latch Cable clamp Small-sized Phillips head screw Small-sized Phillips flat head screw Key rivet A B Part No. PCS-E28LGPA-( )+R 35.0 25.3 C 30 D 16 Outside diameter of cable E for reference purposes 56.5 o5.5, o5.9 PCS-E36LGPA-( )+R 40.2 30.5 34 31 89.5 Because some combinations of "Configurations of Product Part No.", are under consideration for development, please contact us for availability details. For use with connector: PCS-E series IDC type or soldering type female connector for cable PCS-XE series IDC type male connector for cable Accessories: Key-rivets for preventing misinsertion, PCS-E-PK+R Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others o8.4, o9 Key-riveted position No. 1D, 2C, 3B, 4A 1.27 mm pitch connector Horizontal type die-cast material backshell for standard cable with provision for preventing misinsertion PCS-E( )WSP-( )+R Backshell Horizontal EMI-filtered Configuration of product Part No. PCS-E ( ) WSP- ( )+R Series name No. of contacts: 20, 28, 36 or 50 Type of backshell WSP: Horizontal type backshell for standard cables with mating guide for preventing misinsertion Key-riveted position (Refer to the Dimension table as shown below) for preventing misinsertion. 10 22 D C B A 10 A C D 1 2 3 4 B B C A A The form of the 20-contact backshell D C B A The form of the 28-contact backshell 4 B 3 C 2 D 1 E A The form of the 50-contact backshell Key-riveted position No. Components Dimensions Cover A Cover B Cable clamp Latch A A Part No. PCS-E20WSP-( )+R 30.0 PCS-E28WSP-( )+R 35.0 B Latch B Small-sized Phillips flat head screw PCS-E36WSP-( )+R 40.2 o7.6 PCS-E50WSP-( )+R 48.9 o6 Outside diameter of cable for reference purposes Key-riveted position No. o5 1B, 1C, 2A, 3A o5.5 o6 o6.5 1D, 2C, 3B, 4A 1E, 2D, 4B, 5A For use with connector: PCS-E series IDC type or soldering type female connector for cable PCR series IDC type or soldering type female connector for cable PCS-XE series IDC type male connectors for cable Accessories: Key-rivets for preventing misinsertion, PCS-E-PK+R Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole 1.27 mm pitch connector Horizontal type die-cast material backshell for larger diameter cable with provision for preventing misinsertion PCS-E( )WKP( )-( )+R Backshell Horizontal EMI-filtered Configuration of product Part No. PCS-E ( ) WKP ( )- ( )+R Series name No. of contacts: 36, 50, 68, 80 Type of backshell WKP: Horizontal type backshell for larger diameter cables with mating guide for preventing misinsertion Identification mark (A or B) of cable-end-outlet dimension. Cable diameters for reference purposes are shown in the Dimension table as shown below. Key-riveted position (Refer to the Dimension table as shown below) for preventing misinsertion. 35.5 1 2 3 4 37.0 B 11.6 5 10.0 A 1.5 5 4 3 2 1 B A Key-riveted position No. C C D D E E B Components Cable clamp Small-sized Phillips head screw Dimensions Latch Cover B A B Part No. PCS-E36WKPA-( )+R 40.2 10.59.5 PCS-E50WKPB-( )+R 48.9 1210 Cover A Small-sized Phillips flat head screw PCS-E68WKPA-( )+R 60.3 1110 PCS-E80WKPA-( )+R 67.9 10.59.5 Key rivet For use with connector: PCS-E series IDC type or soldering type female connector for cable PCS-XE series IDC type male connector for cable Accessories: Key-rivets for preventing misinsertion, PCS-E-PK+R Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others Outside diameter of cable for reference purposes o9.5 Key-riveted position No. 1D, 2C, 3B, 4A o11.5 o10.5 o9.5 1E, 2D, 4B, 5A 1.27 mm pitch connector Horizontal type die-cast material backshell for larger diameter cable with provision for preventing misinsertion PCS-E96WKP( )-( )+R Backshell Horizontal EMI-filtered Configuration of product Part No. PCS-E 96 WKP ( )- ( )+R Series name No. of contacts: 96 Type of backshell WKP: Horizontal type backshell for larger diameter cables with mating guide for preventing misinsertion Identification mark (B) of cable-end-outlet dimension. Cable diameters for reference purposes are shown in the Dimension table as shown below. Key-riveted position (Refer to the Dimension table as shown below) for preventing misinsertion. 11.6 A 43.2 B E D C B A 1 2 3 4 5 10.0 1.5 78.1 5 4 3 E D C Key rivet 2 (Option) 1 B A Key-riveted position No. Components Cable clamp Small-sized Phillips head screw Latch Cover B Cover A Small-sized Phillips flat head screw Key rivet Dimensions Part No. PCS-E96WKPB-( )+R No. of contacts 96 A 10 B 15 Outside diameter of cable for reference purposes Key-riveted position No. 1E, 2D, 4B, 5A o10 For use with connector: PCS-E series IDC type or soldering type female connector for cable PCR series IDC type or soldering type female connector for cable PCS-XE series IDC type male connector for cable Accessories: Key-rivets for preventing misinsertion, PCS-E-PK+R Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole 1.27 mm pitch connector Vertical type die-cast material backshell for flat cable with provision for preventing misinsertion PCS-E( )LTP-( )+R Backshell Vertical Configuration of product Part No. PCS-E ( ) LTP- ( )+R Series name No. of contacts: 50 or 68 Type of backshell LTP: Vertical type backshell for flat cables with mating guide for preventing misinsertion Key-riveted position (Refer to the Dimension table as shown below) for preventing misinsertion. 10 C 20 A E D C B A B C D E 1 2 3 4 5 C D Small-sized Phillips head screw Hex nuts Part No. PCS-E50LTP-( )+R A 50.9 B 48.9 C 32.2 Key rivet PCS-E68LTP-( )+R 62.3 60.3 43.5 A Key-riveted position No. Components B B E A Cover B Cover A Latch Cable clamp Dimensions For use with connector: PCS-E series IDC type female connector for cable PCS-XE series IDC type male connector for cable Accessories: Key-rivets for preventing misinsertion, PCS-E-PK+R Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others Key-riveted position No. 1E, 2D, 4B, 5A 1.27 mm pitch connector Vertical type die-cast material backshell for larger diameter cable PCS-E68LKAU2N Backshell Vertical SCSI-III Configuration of product Part No. PCS-E 68 LK A U2 N Series name No. of contacts: 68 Type of backshell: Vertical type backshell for lager diameter housing Identification mark (A) of cable-end-outlet dimension. Cable diameters for reference purposes are shown below. Screw size U2: #2-56UNC Lock type N: Screw lock o12.5 o12.2 Cable diameters for reference purposes 32 JAPAN LKA 2.85 17.5 38 JAPAN LKA 57.9 Assembly Diagram 63.8 Connector 7.3 10.0 13.9 Screw size Components Cable clamp Small-sized Phillips head screw Thumb screw Cover A Cover B Small-sized Phillips flat head screw Part No. Screw size PCS-E68LKAU2N #2-56UNC For use with connector: PCS-E series IDC type female connector PCS-XE series IDC type male connector for cable Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole 1.27 mm pitch connector Vertical type over-molded backshell PCS-XEM( )DL( )( )N Backshell Vertical SCSI-III Configuration of product Part No. PCS-XEM ( ) DL ( ) ( ) N Series name No. of contacts: 50 or 68 Type of backshell DL: Vertical type backshell Color of hood Blank: Black 1 : Beige 2 : Green 3 : Grey Screw size Blank: M2.50.45 U : #4-40UNC U2 : #2-56UNC (standard) Lock type N: Screw lock A B 46.0 14.0 23.0 2.85 C E 11.2 D Screw size Components Cable clamp Small-sized Phillips head screw Dimensions Caps Seal A Part No. PCS-XEM50DL( )( )N A 17.6 B o11 C 54.0 D 46.5 E 14.0 Seal B Screw lock PCS-XEM68DL( )( )N 19.3 o12.7 65.43 57.9 15.7 For use with connector: PCS-E series IDC type female connector PCS-XE series IDC type male connector for cable SMT o10.5 o12.2 Because some combinations of "Configurations of Product Part No.", are under consideration for development, please contact us for availability details. Hood Through hole Outside diameter of cable for reference purposes Press-in IDC Wire Soldering Crimping wrapping Others Part No. PCS-XEM( )DL( )N Screw size PCS-XEM( )DL( )UN #4-40UNC PCS-XEM( )DL( )U2N #2-56UNC M2.50.45 1.27 mm pitch connector Vertical type over-molded backshell PCS-XEM100L( )( ) Backshell Vertical Screw locks Configuration of product Part No. PCS-XEM 100 L ( ) ( ) Screw size Blank: #4-40UNC U2 : #2-56UNC 10.8 16 Series name No. of contacts: 100 Type of backshell L: Vertical type backshell Color of hood Blank: Black 1 : Beige 40 20 o13.4 14 2.8 3.5 12.5 10 72 78.23 37 51 REF. 85.1 Components Cable clamp Small-sized Phillips head screw Hood Fastening screw Shield B Shield A Dimensions Part No. PCS-XEM100L PCS-XEM100LU2 PCS-XEM100L1 PCS-XEM100L1U2 Color of housing Screw size Black Beige Outside diameter of cable for reference purposes #4-40UNC #2-56UNC o13.2 #4-40UNC #2-56UNC For use with connector: PCS-XE series IDC type male connector for cable Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole 1.27 mm pitch connector Vertical type die-cast material backshell for daisy chain connection PCS-SE68LDAU2N Backshell Vertical SCSI-III Configuration of product Part No. PCS-SE 68 LD A U2 N Series name No. of contacts: 68 Type of backshell LD: Vertical type backshell Identification mark (A) of cable-end-outlet dimension. Screw size U2: #2-56UNC Lock type N: Screw lock 16.4 Cable diameters for reference purposes o11.5 o11 55 45 5 25 2.85 57.9 63.8 Assembly Diagram 13.2 11.4 #2-56UNC Components Cable clamp Small-sized Phillips head screw Thumb screw Case B Case A Small-sized Phillips head screw For use with connector: PCS-XES series soldering type male connector for cable Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others Connector Mating connector: P/N: PCS-XES68MS 1.27 mm pitch connector 1.6 mm panel-thickness mating guide PCS-E( )G Accessories Mating guide Configuration of product Part No. PCS-E ( ) G Series name No. of contacts: 20, 28, 36 or 50 1.6 mm panel-thickness mating guide (Color: Silver metallic) A 16.5 7.2 11.0 15.0 10.8 t=1.6 For panel B 1.5 C 2.8 15 0 7.5 +0.15 12 R1.4 2.5 14.5 REF. E F D Recommended panel cut-out dimensions Dimensions Because some combinations of "Configurations of Product Part No.", are under consideration for development, please contact us for availability details. For use with connector: PCS-E series vertical type or horizontal type housing Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others Part No. PCS-E20G A 37.3 B 30.7 C 11 D 27.4 E 23.7 F 11.3 PCS-E28G 42.3 35.7 16 32.5 28.8 16.3 PCS-E36G 47.6 40.9 20 37.6 33.9 20.3 PCS-E50G 56.3 49.6 30 46.5 42.8 30.3 1.27 mm pitch connector 1.0 mm panel-thickness mating guide PCS-E( )G1 Accessories Mating guide Configuration of product Part No. PCS-E ( ) G1 Series name No. of contacts: 20, 28, 36, 50 or 68 1.0 mm panel-thickness mating guide A B H C 16.5 9.9 4 1.7 10.5 12.5 11.0 12.2 15.0 t=1.0 For panel 0.9 F G 1.6 10.4 12 R1.4 15 7.5 D 2.8 1.9 +0.15 0 13.9 REF. J E Recommended panel cut-out dimensions Dimensions C Part No. PCS-E20G1 A 37.3 B 30.7 11 D 33.0 E 27.4 F 23.7 G 11.3 H 25 J 8 PCS-E28G1 42.3 35.7 16 38.1 32.5 28.8 16.3 30 16 PCS-E36G1 47.6 40.9 20 43.2 37.6 33.9 20.3 34 31 PCS-E50G1 56.3 49.6 30 52.1 46.5 42.8 30.3 42 39 PCS-E68G1 67.7 61.0 40 63.5 57.9 54.1 40.3 52 49 For use with connector: PCS-E series vertical type housing for standard cable or heavy wire cable with mating guide Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole 1.27 mm pitch connector Metallic mating guide PCS-E( )G3( ) Accessories Mating guide Configuration of product Part No. PCS-E ( ) G3 ( ) Series name No. of contacts: 20, 28, 36, 50 or 68 Metallic mating guide Guide plating Blank: No plating N : Nickel plating A B C D (R2.75) 10 7.5 2.8 10.7 11.2 MAX. o2.6 R1.5 E (R1.75) F 7.2 Dimples Dimensions Part No. Note 1: Panel thickness: 1-1.6 mm B 31 C 30.5 D 27.4 E 22.6 F 23.7 PCS-E28G3( ) 38 36.1 35.6 32.5 27.7 28.8 PCS-E36G3( ) 43.1 41.2 40.7 37.6 32.8 33.9 PCS-E50G3( ) 52 50.1 49.6 46.5 41.7 42.8 one side6 PCS-E68G3( ) 63.4 61.5 61.0 57.9 53.1 54.2 one side8 For use with connector: PCS-E series vertical type housing for standard cable or heavy wire cable PCS-E series of horizontal type housing for standard cable or heavy wire cable Through hole SMT Press-in IDC Wire Soldering Crimping wrapping No. of dimples A 33 PCS-E20G3( ) Others one side4 one side5 1.27 mm pitch connector Key rivet for preventing misinsertion PCS-E-PK+R Accessories Key rivet Configuration of product Part No. PCS-E- PK+R Series name Key rivet for preventing misinsertion 1.65 o1.95 o3 0.7 Caulk rivet (Use specialized tool.) For use with backshell: PCS-E series vertical type backshell or horizontal type backshell with provision for preventing misinsertion Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others 1.27 mm pitch connector Misinsertion prevention guide PCS-E( )PG-( ) Accessories Misinsertion prevention guide Configuration of product Part No. PCS-E ( ) PG- ( ) 3 For 20-contacts 2-R1.3 2 1 D C 4 3 A B C D 7.5 B A For 28-contacts 2 1 D C 4 3 For 36-contacts B A 2 1 C E D 5 4 3 4 Note 1: When a panel is not used, use the spacer hardware, PCS-E( )M-SP. B Directional form A A 2 1.5 2-R2.1 1 10.1 2 4-R1 1 C C B Key No. A 1.1 REF. Series name No. of contacts: 20, 28, 36, 50, 68 or 80 Misinsertion prevention guide Locations being cut off the key forms for preventing misinsertion B 3 For 50-contacts 2 1 C E D 5 4 3 1.1 M2.5 o4 5 4 0.2 MAX. 2 1 E For 80-contacts Dimensions A 1 B 2 C 3 D 4 Because some combinations of "Configurations of Product Part No.", are under consideration for development, please contact us for availability details. D Attached small screw C Example: PCS-E36G4-1D For 68-contacts B Note 2: Designate the location No. in parentheses () for "Configuration of product part numbers." (Standard locations being cut off the key forms for preventing misinsertion are shown in the Dimension table.) 6 A 0.8 3 1.5 3.7 B A 1.7 Part No. PCS-E20PG-( ) A 32.6 B 30.3 C 27.4 PCS-E28PG-( ) 37.7 35.3 32.5 PCS-E36PG-( ) 42.8 40.5 37.6 PCS-E50PG-( ) 51.7 49.2 46.5 PCS-E68PG-( ) 63.1 60.6 57.9 PCS-E80PG-( ) 70.7 68.2 65.5 Standard locations being cut off the key forms for preventing misinsertion 1B, 1C, 2A, 3A 1D, 2C, 3B, 4A 1E, 2D, 4B, 5A For use with connector: PCS-E series right-angle through hole type male connector for PCB PCR-E series right-angle through hole type male connector for PCB Mating backshell: PCS-E series of backshell with provision for preventing misinsertion Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole 1.27 mm pitch connector Misinsertion prevention guide PCS-E96PG-( ) Accessories Misinsertion prevention guide Configuration of product Part No. PCS-E 96 PG- ( ) Series name No. of contacts: 96 Misinsertion prevention guide Locations being cut off the key forms for preventing misinsertion Key No. 80.9 75.69 52 2-R1.3 B C D E 10.1 7.5 A 2 3 4 5 R 1 1 58 3- 1.5 2-R2.1 Directional form 78.4 5 8 8 8 8 2.5 2.1 4.7 7.6 1.7 0.8 6 o4 Location No.: 1E, 2D, 4B or 5A Example: PCS-E96PG-1E M2.5 Note1: Designate one of location numbers below in parentheses () for "Configuration of product part numbers." (Standard locations being cut off the key forms for preventing misinsertion are shown below.) A B C D E Attached small screw 1 2 3 4 5 Because some combinations of "Configurations of Product Part No.", are under consideration for development, please contact us for availability details. For use with backshell: PCS-E series backshell with provision for preventing misinsertion. PCS-E96LKP( )-( ) Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others 1.27 mm pitch connector Spacer hardware for male connector PCS-E( )M-SP Accessories Spacer hardware Configuration of product Part No. PCS-E ( ) M-SP Series name No. of contacts: 20, 28, 36, 50, 68 or 96 Spacer hardware for male connectors A B 2.6 7.5 10 C 2-R1.3 Plate thickness: 1.0 mm. Dimensions Use this spacer hardware for male connectors, when a panel is not used. Part No. PCS-E20M-SP A 32.8 B 27.4 C 22.8 PCS-E28M-SP 37.9 32.5 27.9 PCS-E36M-SP 43.0 37.6 33.0 PCS-E50M-SP 51.9 46.5 41.9 PCS-E68M-SP 63.3 57.9 53.3 PCS-E96M-SP 81.1 75.69 71.1 For use with connector: PCS-E series right-angle through hole type male connector for PCB PCR-E series right-angle through hole type male connector for PCB Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole 1.27 mm pitch connector Screw lock PCS-XE50SJ( )U2 Accessories Screw locks SCSI-III Configuration of product Part No. PCS-XE 50 SJ( ) U2 Series name Kinds of screw locks SJ1: The type not mounted on panel (Male screw size, #4-40UNC) SJ5: The type mounted on 1.6 mm panel (Male screw size, #4-40UNC) SJ6: The type mounted on 1.0 mm panel (Male screw size, #4-40UNC) Female screw size U2: #2-56UNC A B C #4-40UNC D G F 5.48 REF. 4.75 E Note 1: SJ1 and SJ5 types are not slotted. Dimensions Part No. PCS-XE50SJ1U2 A PCS-XE50SJ5U2 8.9 PCS-XE50SJ6U2 For use with backshell: PCS-E series Backshells with provision for preventing misinsertion Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others B C 5.5 2.7 3.9 4.1 4.5 3.5 D - 1.1 E 3 2.9 3 F - 0.8 G #2-56UNC