Product # MCOTS-C-28-12-QT Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005277 Rev. D 02/04/13
Page 1
MCOTS-C-28-12-QT
Single Output
Quarter-brick
MCOTS-C-28-12-QT-N-M
DC/DC CONVERTER
28
IN 12V
OUT @ 10A
The
MilQor series of Mil-COTS DC/DC converters brings
SynQor’s field proven high-efficiency synchronous
rectification technology to the Military/Aerospace
industry. SynQor’s ruggedized encased packaging
approach ensures survivability in demanding
environments. Compatible with the industry standard
format, these converters operate at a fixed frequency,
and follow conservative component derating guidelines.
They are designed and manufactured to comply with a
wide range of military standards.
Full Power Operation: -55°C to +100°C
Mil-COTS
MILITARY COTS DC/DC CONVERTER
Designed and Manufactured in the USA
16-40V 16-50V 12V 10A 91% @ 5A / 90% @ 10A
Continuous Input Transient Input Output Output Efciency
Protection Features
•Input under-voltage lockout
•Output current limit and short circuit protection
•Active back bias limit
•Output over-voltage protection
•Thermal shutdown
Screening/Qualification
• AS9100 and ISO 9001:2008 certied facility
• Qualication consistent with MIL-STD-883
•Available with S-Grade or M-Grade screening
• Temperature cycling per MIL-STD-883, Method 1010,
Condition B, 10 cycles
•Burn-In at 100C baseplate temperature
• Final visual inspection per MIL-STD-2008
•Full component traceability
Operational Features
• High efciency, 90% at full rated load current
•Operating input voltage range: 16-40 V
•Fixed frequency switching provides predictable EMI
•No minimum load requirement
Control Features
•On/Off control referenced to input return
•Remote sense for the output voltage
• Output voltage trim range of +10%, -20%
Safety Features
• 2250V, 30 MΩ input-to-output isolation
• Certied 60950-1 requirement for basic insulation
(see Standards and Qualications page)
Mechanical Features
•Industry standard quarter-brick pin-out
•Size: 1.54” x 2.39” x 0.50”
(39.0 x 60.6 x 12.7 mm)
• Total weight: 3.02 oz. (85.7 g)
•Flanged baseplate version available
Technical Specification
MCOTS-C-28-12-QT
Output:
12V
Current:
10A
Product # MCOTS-C-28-12-QT Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005277 Rev. D 02/04/13
Page 2
BLOCK DIAGRAM
TYPICAL CONNECTION DIAGRAM
Vin
External
Input
Filter
Trim
Vin(+)
Iload
Cload
Vout(+)
Rtrim-up
or
Rtrim-down
Vsense(+)
ON/OFF
Vin(_)Vout(_)
Vsense(_)
Electrolytic
Capacitor
−
SENSE
ISOLATION STAGEREGULATION STAGE
8
4
UVLO
OVSD
SECONDARY
CONTROL
GATE CONTROL
PRIMARY
CONTROL
POSITIVE
INPUT
INPUT
RETURN
ON/OFF
6
7
5
1
3
2
POSITIVE
OUTPUT
OUTPUT
RETURN
TRIM
+ SENSE
GATE DRIVERS
ISOLATION BARRIER
T1 T1T2 T2
CURRENT
LIMIT
CURRENT
SENSE
OPTO-ISOLATION
DATA COUPLING
Technical Specification
MCOTS-C-28-12-QT
Output:
12V
Current:
10A
Product # MCOTS-C-28-12-QT Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005277 Rev. D 02/04/13
Page 3
MCOTS-C-28-12-QT ELECTRICAL CHARACTERISTICS
Tb = 25 °C, Vin = 28 Vdc unless otherwise noted; full operating temperature range is -55 °C to +100 °C baseplate temperature with appropriate power
derating. Specications subject to change without notice.
Parameter Min. Typ. Max. Units Notes & Conditions
ABSOLUTE MAXIMUM RATINGS
Input Voltage
Non-Operating 60 V Continuous
Operating 40 V Continuous
Operating Transient Protection 50 V 1 s transient, square wave
Isolation Voltage
Input to Output 2250 V dc
Input to Base-Plate 2250 V dc
Output to Base-Plate 2250 V dc
Operating Temperature -55 100 °C Baseplate temperature
Storage Temperature -65 135 °C
Voltage at ON/OFF input pin -2 18 V
INPUT CHARACTERISTICS
Operating Input Voltage Range 16 28 40 V 50V transient for 1 s
Input Under-Voltage Lockout
Turn-On Voltage Threshold 15.0 15.3 15.6 V
Turn-Off Voltage Threshold 14.0 14.3 14.6 V
Lockout Voltage Hysteresis 1.0 V
Recommended External Input Capacitance 100 µF Typical ESR 0.1-0.2 Ω
Input Filter Component Values (L\C) 1.0\6.6 µH\µF Internal values; see Figure E
Maximum Input Current 11.0 A Vin min; trim up; in current limit
No-Load Input Current 130 160 mA
Disabled Input Current 2 4 mA
Response to Input Transient 0.4 V See Figure 6
Input Terminal Ripple Current 425 mA RMS
Recommended Input Fuse 20 A Fast acting external fuse recommended
OUTPUT CHARACTERISTICS
Output Voltage Set Point 11.88 12.00 12.12 V
Output Voltage Regulation
Over Line ±0.1 ±0.3 %
Over Load ±0.1 ±0.3 %
Over Temperature -180 180 mV
Total Output Voltage Range 11.7 12.3 V Over sample, line, load, temperature & life
Output Voltage Ripple and Noise 20 MHz bandwidth; see Note 1
Peak-to-Peak 0 25 50 mV Full load
RMS 6 10 mV Full load
Operating Output Current Range 0 10 A Subject to thermal derating
Output DC Current-Limit Inception 11 12 13 A Output voltage 10% Low
Output DC Current-Limit Shutdown Voltage 5 V
Back-Drive Current Limit while Enabled 0.45 A Negative current drawn from output
Back-Drive Current Limit while Disabled 5 mA Negative current drawn from output
Maximum Output Capacitance 1500 µF Vout nominal at full load (resistive load)
Output Voltage during Load Current Transient
Step Change in Output Current (0.1 A/µs) 500 mV 50% to 75% to 50% Iout max
Settling Time 100 µs To within 1% Vout nom
Output Voltage Trim Range -20 10 % Across Pins 8&4; Figure C; see Note 2
Output Voltage Remote Sense Range 10 % Across Pins 8&4
Output Over-Voltage Protection 14.04 14.64 15.24 V Over full temp range
EFFICIENCY
100% Load 90 % See Figure 1 for efciency curve
50% Load 91 % See Figure 1 for efciency curve
Note 1: Output is terminated with 1 µF ceramic and 15 µF low-ESR tantalum capacitors. For applications requiring reduced output voltage ripple and
noise, consult SynQor applications support (e-mail: mqnbofae@synqor.com)
Note 2: Trim-up range is limited below 10% at low line and full load.
Technical Specification
MCOTS-C-28-12-QT
Output:
12V
Current:
10A
Product # MCOTS-C-28-12-QT Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005277 Rev. D 02/04/13
Page 4
MCOTS-C-28-12-QT ELECTRICAL CHARACTERISTICS
Tb = 25 °C, Vin = 28 Vdc unless otherwise noted; full operating temperature range is -55 °C to +100 °C baseplate temperature with appropriate power
derating. Specications subject to change without notice.
Parameter Min. Typ. Max. Units Notes & Conditions
DYNAMIC CHARACTERISTICS
Turn-On Transient
Turn-On Time 9 ms Full load, Vout=90% nom.
Start-Up Inhibit Time 200 230 250 ms See Figure F
Output Voltage Overshoot 0 % Maximum Output Capacitance
ISOLATION CHARACTERISTICS
Isolation Voltage (dielectric strength) See Absolute Maximum Ratings
Isolation Resistance 30 MΩ
Isolation Capacitance (input to output) 1000 pF See Note 1
TEMPERATURE LIMITS FOR POWER DERATING CURVES
Semiconductor Junction Temperature 125 °C Package rated to 150 °C
Board Temperature 125 °C UL rated max operating temp 130 °C
Transformer Temperature 125 °C
Maximum Baseplate Temperature, Tb 100 °C
FEATURE CHARACTERISTICS
Switching Frequency 230 250 270 kHz For both input and isolation stage
ON/OFF Control
Off-State Voltage 2.4 1.8 V
On-State Voltage -2.0 0.8
ON/OFF Control Application notes Figures A & B
Pull-Up Voltage 5 V
Pull-Up Resistance 50 kΩ
Over-Temperature Shutdown OTP Trip Point 125 °C Average PCB Temperature
Over-Temperature Shutdown Restart Hysteresis 10 °C
RELIABILITY CHARACTERISTICS
Calculated MTBF per MIL-HDBK-217F 3.4 106 Hrs. Ground Benign, 70°C Tb
Calculated MTBF per MIL-HDBK-217F 0.58 106 Hrs. Ground Mobile, 70°C Tb
Note 1: Higher values of isolation capacitance can be added external to the module.
STANDARDS COMPLIANCE
Parameter Notes & Conditions
STANDARDS COMPLIANCE
UL 60950-1:2007 Basic Insulation
CAN/CSA-C22.2 No. 60950-1:2007
EN60950-1/A12:2011
Note: An external input fuse must always be used to meet these safety requirements. Contact SynQor for ofcial safety certicates on new releases or
download from the SynQor website.
Technical Specification
MCOTS-C-28-12-QT
Output:
12V
Current:
10A
Product # MCOTS-C-28-12-QT Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005277 Rev. D 02/04/13
Page 5
60
65
70
75
80
85
90
95
0 2 4 6 8 10
Load Current (A)
Efficiency (%)
16 Vin
28 Vin
40 Vin
Figure 1: Efficiency at nominal output voltage vs. load current for
minimum, nominal, and maximum input voltage at 25
°
C.
Figure 2: Efficiency at nominal output voltage and 60% rated power vs.
case temperature for minimum, nominal, and maximum input voltage.
Figure 3: Power dissipation at nominal output voltage vs. load current
for minimum, nominal, and maximum input voltage at T
CASE=25
°
C.
Figure 4: Power dissipation at nominal output voltage and 60% rated
power vs. case temperature for minimum, nominal, and maximum input
voltage.
Figure 6: Output voltage vs. load current showing typical current limit
curves. See Current Limit section in the Application Notes.
60
65
70
75
80
85
90
95
-55ºC 25ºC 100ºC
Efficiency (%)
16 Vin
28 Vin
40 Vin
0
2
4
6
8
10
12
14
16
18
-55ºC 25ºC 100ºC
Case Temperature (ºC)
Power Dissipation (W)
16 Vin
28 Vin
40 Vin
0
2
4
6
8
10
12
14
16
18
0 2 4 6 8 10
Load Current (A)
Power Dissipation (W)
16 Vin
28 Vin
40 Vin
0
2
4
6
8
10
12
14
0 2 4 6 8 10 12 14
Load Current (A)
Output Voltage (V)
16 Vin
28 Vin
40 Vin
Figure 5: Maximum output current vs. base plate temperature (nominal input
voltage).
0
2
4
6
8
10
12
50 60 70 80 90 100 110
Iout (A)
Base Plate Temperature (°C)
Technical Specification
MCOTS-C-28-12-QT
Output:
12V
Current:
10A
Product # MCOTS-C-28-12-QT Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005277 Rev. D 02/04/13
Page 6
Figure 9: Input terminal current ripple, iC, at full rated output current and
nominal input voltage with SynQor MCOTS lter module (200 mA/div).
Bandwidth: 20MHz. See Figure 17.
Figure 10: Output voltage ripple, Vout, at nominal input voltage and rated
load current (20 mV/div). Load capacitance: 1µF ceramic capacitor and 10µF
tantalum capacitor. Bandwidth: 10 MHz. See Figure 17.
Figure 12: Output voltage response to step-change in input voltage (250V/ms).
Load cap: 100 µF electrolytic output capacitance. Ch 1: Vout (500mV/div), Ch
2: Vin (20V/div).
Figure 11: Output voltage response to step-change in load current (50%-
75%-50% of Iout(max); dI/dt = 0.1 A/µs). Load cap: 1 µF ceramic and 15 µF
tantalum capacitors. Ch 1: Vout (500mV/div), Ch 2: Iout (5A/div).
Figure 8: Turn-on transient at full resistive load and zero output capacitance
initiated by Vin. ON/OFF Pin previously low. Ch 1: Vout (20V/div). Ch 3: Vin
(5V/div).
Figure 7: Typical startup waveform. Input voltage pre-applied, ON/OFF Pin on
Ch 1.
Technical Specification
MCOTS-C-28-12-QT
Output:
12V
Current:
10A
Product # MCOTS-C-28-12-QT Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005277 Rev. D 02/04/13
Page 7
Figure 13: Magnitude of incremental output impedance (Zout = vout/
iout) for minimum, nominal, and maximum input voltage at full rated
power.
Figure 14: Magnitude of incremental forward transmission (FT = vout/
vin) for minimum, nominal, and maximum input voltage at full rated
power.
Figure 15: Magnitude of incremental reverse transmission (RT = iin/
iout) for minimum, nominal, and maximum input voltage at full rated
power.
Figure 16: Magnitude of incremental input impedance (Zin = vin/iin)
for minimum, nominal, and maximum input
voltage at full rated power.
Figure 17: Test set-up diagram showing measurement points for Input Terminal
Ripple Current (Figure 9) and Output Voltage Ripple (Figure 10).
DC/DC
Converter
VSOURCE
iCVOUT
0.0001
0.001
0.01
0.1
1
10 100 1,000 10,000 100,000
Output Impedance (ohms)
Hz
16 Vin
28 Vin
40 Vin
0.1
1
10
100
10 100 1,000 10,000 100,000
Input Impedance (ohms)
Hz
16 Vin
28 Vin
40 Vin
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
10 100 1,000 10,000 100,000
Forward Transmission (dB)
Hz
16 Vin
28 Vin
40 Vin
-30
-25
-20
-15
-10
-5
0
5
10
10 100 1,000 10,000 100,000
Reverse Transmission (dB)
Hz
16 Vin
28 Vin
40 Vin
4.7 µH
source impedance
100 µF,
0.2Ω ESR
electrolytic capacitor
10 µF,
100mΩ ESR
tantalum capacitor
1 µF
ceramic capacitor
Figure 18: Load current (5A/div) as a function of time (2ms/div and 50ms/div)
when the converter attempts to turn on into a 10 mΩ short circuit.
Technical Specification
MCOTS-C-28-12-QT
Output:
12V
Current:
10A
Product # MCOTS-C-28-12-QT Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005277 Rev. D 02/04/13
Page 8
Figure A: Various circuits for driving the ON/OFF pin. Figure B: Internal ON/OFF pin circuitry
TTL
5V
50k
50k
ON/OFF
Vin(_)
100pF
Open Collector Enable Circuit
Remote Enable Circuit
Direct Logic Drive
Negative Logic
(Permanently
Enabled)
ON/OFF
Vin(_)
ON/OFF
ON/OFF
Vin(_)
ON/OFF
5V
TTL/
CMOS
Vin(_)
Vin(_)
OPEN
This Mil-COTS converter series uses a two-stage power
conversion topology. The rst stage is a buck-converter that
keeps the output voltage constant over variations in line, load,
and temperature. The second stage uses a transformer to
provide the functions of input/output isolation and voltage
step-up or step-down to achieve the output voltage required.
Both the rst stage and the second stage switch at a xed
frequency for predictable EMI performance. Rectication of the
transformer’s output is accomplished with synchronous rectiers.
These devices, which are MOSFETs with a very low on-state
resistance, dissipate far less energy than Schottky diodes. This
is the primary reason that the converter has such high efciency,
even at very low output voltages and very high output currents.
These converter are offered totally encased to withstand
harsh environments and thermally demanding applications.
Dissipation throughout the converter is so low that
it does not require a heatsink for operation in many
applications; however, adding a heatsink provides improved
thermal derating performance in extreme situations.
This series of converters use the industry standard footprint
and pin-out conguration.
BASIC OPERATION AND FEATURES CONTROL FEATURES
REMOTE ON/OFF (Pin 2): The ON/OFF input, Pin 2, permits
the user to control when the converter is on or off. This input
is referenced to the return terminal of the input bus, Vin(-).
The ON/OFF signal is active low (meaning that a low turns the
converter on). Figure A details four possible circuits for driving
the ON/OFF pin. Figure B is a detailed look of the internal ON/
OFF circuitry.
REMOTE SENSE(+) (Pins 7 and 5): The SENSE(+) inputs
correct for voltage drops along the conductors that connect the
converter’s output pins to the load.
Pin 7 should be connected to Vout(+) and Pin 5 should be
connected to Vout(-) at the point on the board where regulation
is desired. A remote connection at the load can adjust for a
voltage drop only as large as that specified in this datasheet,
that is
[Vout(+) - Vout(-)] – [Vsense(+) - Vsense(-)] <
Sense Range % x Vout
Pins 7 and 5 must be connected for proper regulation of
the output voltage. If these connections are not made, the
converter will deliver an output voltage that is slightly higher
than its specified value.
Note: the output over-voltage protection circuit senses the
voltage across the output (pins 8 and 4) to determine when
it should trigger, not the voltage across the converter’s sense
leads (pins 7 and 5). Therefore, the resistive drop on the board
should be small enough so that output OVP does not trigger,
even during load transients.
Technical Specification
MCOTS-C-28-12-QT
Output:
12V
Current:
10A
Product # MCOTS-C-28-12-QT Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005277 Rev. D 02/04/13
Page 9
OUTPUT VOLTAGE TRIM (Pin 6): The TRIM input permits the
user to adjust the output voltage across the sense leads up or
down according to the trim range specifications.
To decrease the output voltage, the user should connect a
resistor between Pin 6 and Pin 5 (SENSE(-) input). For a desired
decrease of the nominal output voltage, the value of the resistor
should be
Rtrim-down =
(
511
)
- 10.22 (kW)
D%
where
D% =
Vnominal – Vdesired
x 100%
Vnominal
To increase the output voltage, the user should connect a
resistor between Pin 6 and Pin 7 (SENSE(+) input). For a desired
increase of the nominal output voltage, the value of the resistor
should be
Trim graphs show the relationship between the trim resistor
value and Rtrim-up and Rtrim-down, showing the total range the
output voltage can be trimmed up or down.
Note: the TRIM feature does not affect the voltage at which the
output over-voltage protection circuit is triggered. Trimming the
output voltage too high may cause the over-voltage protection
circuit to engage, particularly during transients.
It is not necessary for the user to add capacitance at the Trim
pin. The node is internally bypassed to eliminate noise.
Total DC Variation of V
OUT
: For the converter to meet its full
specifications, the maximum variation of the dc value of V
OUT
, due
to both trimming and remote load voltage drops, should not be
greater than that specified for the output voltage trim range.
PROTECTION FEATURES
Input Under-Voltage Lockout: The converter is designed
to turn off when the input voltage is too low, helping avoid an
input system instability problem, described in more detail in
the application note titled “
Input System Instability
” on our
website. The lockout circuitry is a comparator with dc hysteresis.
When the input voltage is rising, it must exceed the typical Turn-
On Voltage Threshold value (listed on the specifications page)
before the converter will turn on. Once the converter is on,
the input voltage must fall below the typical Turn-Off Voltage
Threshold value before the converter will turn off.
Output Over-Voltage Limit: If the voltage across the output
pins exceeds the Output Over-Voltage Protection threshold, the
converter will immediately stop switching. This prevents damage
to the load circuit due to 1) excessive series resistance in output
current path from converter output pins to sense point, 2) a
release of a short-circuit condition, or 3) a release of a current
limit condition. Load capacitance determines exactly how high
the output voltage will rise in response to these conditions. After
200 ms the converter will automatically restart.
Over-Temperature Shutdown: A temperature sensor on
the converter senses the average temperature of the module.
The thermal shutdown circuit is designed to turn the converter
off when the temperature at the sensed location reaches the
Over-Temperature Shutdown value. It will allow the converter
to turn on again when the temperature of the sensed location
falls by the amount of the Over-Temperature Shutdown Restart
Hysteresis value.
Rtrim-up
(k
W)
where V
out
= Nominal Output Voltage
511
_ 10.22
5.11VOUT x
(100+
D%)
1.225D%D%
)
=
(
_
Figure C: Trim graph for trim-up, trim down.
10
100
1,000
10,000
100,000
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Trim Resistance (kΩ)
% Increase in Vout % Decrease in Vout
Output Current Limit: The maximum current limit remains
constant as the output voltage drops. However, once the
impedance of the load across the output is small enough to
make the output voltage drop below the specied Output
DC Current-Limit Shutdown Voltage, the converter turns off.
The converter then enters a “hiccup” mode where it repeatedly
turns on and off at a 5 Hz (nominal) frequency with 5% duty
cycle until the short circuit condition is removed. This prevents
excessive heating of the converter or the load board.
Technical Specification
MCOTS-C-28-12-QT
Output:
12V
Current:
10A
Product # MCOTS-C-28-12-QT Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005277 Rev. D 02/04/13
Page 10
APPLICATION CONSIDERATIONS
Figure D: Typical application circuit (negative logic unit, permanently enabled).
Figure E: Internal Input Filter Diagram
Vin
External
Input
Filter
Trim
Vin(+)
Iload
Cload
Vout(+)
Rtrim-up
or
Rtrim-down
Vsense(+)
ON/OFF
Vin(_)Vout(_)
Vsense(_)
Electrolytic
Capacitor
Input System Instability: This
condition can occur because
any dc-dc converter appears incrementally as a negative
resistance load. A detailed application note titled “Input System
Instability” is available on the SynQor website which provides
an understanding of why this instability arises, and shows the
preferred solution for correcting it.
Application Circuits: Figure D provides a typical circuit diagram
which details the input filtering and voltage trimming.
Input Filtering and External Capacitance:
Figure E
provides
a diagram showing the internal input filter components. This filter
dramatically reduces input terminal ripple current, which otherwise
could exceed the rating of the converter's external electrolytic
input capacitor. The recommended external input capacitance
is specified in the Input Characteristics section on the
Electrical
Characteristics page.
More detailed information is available in
the application note titled “
EMI Characteristics
” on the
SynQor
website.
L
Vin(+)
Vin(_)
C
Vout(+)
Vout(-)
Internal
Input
Filter
Converter
Technical Specification
MCOTS-C-28-12-QT
Output:
12V
Current:
10A
Product # MCOTS-C-28-12-QT Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005277 Rev. D 02/04/13
Page 11
Figure F: Startup Inhibit Period (turn-on time not to scale)
Under-Voltage
Lockout Turn-
On Threshold
ON/OFF
(neg logic)
Vout
Vin
200ms 200ms
200ms
(typical start-up
inhibit period)
t0t1t2
t
ON ON ON
OFF OFF
9ms
(turn on time)
Startup Inhibit Period: The Startup Inhibit Period ensures
that the converter will remain off for approximately 200 ms
when it is shut down for any reason. When an output short is
present, this generates a 5 Hz “hiccup” mode, which prevents the
converter from overheating. In all, there are seven ways that the
converter can be shut down, initiating a Startup Inhibit Period:
• Input Under-Voltage Lockout
• Input Over-Voltage Lockout
• Output Over-Voltage Protection
• Over Temperature Shutdown
• Current Limit
• Short Circuit Protection
• Turned off by the ON/OFF input
Figure F shows three turn-on scenarios, where a Startup Inhibit
Period is initiated at t0, t1, and t2:
Before time t0, when the input voltage is below the UVL threshold,
the unit is disabled by the Input Under-Voltage Lockout feature.
When the input voltage rises above the UVL threshold, the Input
Under-Voltage lockout is released, and a Startup Inhibit Period is
initiated. At the end of this delay, the ON/OFF pin is evaluated,
and since it is active, the unit turns on.
At time t1, the unit is disabled by the ON/OFF pin, and it cannot
be enabled again until the Startup Inhibit Period has elapsed.
When the ON/OFF pin goes high after t
2
, the Startup Inhibit
Period has elapsed, and the output turns on within the typical
Turn-On Time.
Thermal Considerations: The maximum operating base-
plate temperature, T
B
, is 100 ºC. Refer to the thermal derating
curve, Figure 5, to see the available output current at baseplate
temperatures below 100 ºC.
A power derating curve can be calculated for any heatsink that is
attached to the base-plate of the converter. It is only necessary
to determine the thermal resistance, RTH
BA
, of the chosen heatsink
between the base-plate and the ambient air for a given airflow
rate. This information is usually available from the heatsink
vendor. The following formula can then be used to determine the
maximum power the converter can dissipate for a given thermal
condition:
Pmax = T
B
- T
A
diss RTH
BA
This value of power dissipation can then be used in conjunction
with the data shown in Figure 3 to determine the maximum load
current (and power) that the converter can deliver in the given
thermal condition.
Technical Specification
MCOTS-C-28-12-QT
Output:
12V
Current:
10A
Product # MCOTS-C-28-12-QT Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005277 Rev. D 02/04/13
Page 12
Top View
1.536 ±0.020 (39.01 ±0.5)
1. 030 (26.16)
0.600 (15.24)
0.450 (11.43)
0.300 (7.62)
0.150 (3.81)
123
8 7 5 46
2.386
± 0.020
(60.6± 0.5)
2.00
(50.8) 1.86
(47.2)
M3 Threaded Inserts
4 Places See Notes
0.253±0.020
(6.4±0.5)
0.183±.020 (4.65)±0.5
0.300 (7.62)
0.600 (15.24)
0.468±0.020 (11.89±0.5)
0.263±0.020
(6.68±0.5)
0.500±0.025
(12.7±0.63)
Overall Height
0.18±0.010
(4.57±0.25)
Side View
Mechanical Drawing – Normal Thermal Design Option
NOTES
1) M3 screws used to bolt unit’s baseplate to other surfaces (such as a
heatsink) must not exceed 0.100" (2.54 mm) depth below the
surface of the baseplate.
2) Applied torque per screw should not exceed 6in-lb (0.7 Nm).
3) Baseplate flatness tolerance is 0.004" (.10mm) TIR for surface.
Pins 1-3, 5-7 are 0.040” (1.02mm) diameter, with 0.080” (2.03mm)
4) diameter standoff shoulders.
Pins 4 and 8 are 0.062” (1.57 mm) diameter with 0.100" (2.54 mm)
5) diameter standoff shoulders.
6) All Pins: Material – Copper Alloy; Finish – Matte Tin over Nickel plate
7) Undimensioned components are shown for visual reference only.
8) Weight: 3.02 oz. (85.7 g) typical
9) All dimensions in inches (mm)
Tolerances: x.xx +/-0.02 in. (x.x +/-0.5mm)
x.xxx +/-0.010 in. (x.xx +/-0.25mm)
10) Workmanship: Meets or exceeds IPC-A610 Class II
Recommended pin length is 0.03” (0.76mm) greater than the PCB
thickness.
PIN DESIGNATIONS
Pin Name Function
1 Vin(+) Positive input voltage
2 ON/OFF TTL input to turn converter on and off,
referenced to Vin(–), with internal pull up.
3 IN RTN Input return
4 OUT RTN Output return
5 SENSE(–) Negative remote sense1
6 TRIM Output voltage trim2
7 SENSE(+) Positive remote sense3
8 Vout(+) Positive output voltage
Notes:
1) SENSE(–) should be connected to Vout(–) either remotely or
at the converter.
2) Leave TRIM pin open for nominal output voltage.
3) SENSE(+) should be connected to Vout(+) either remotely or
at the converter.
Technical Specification
MCOTS-C-28-12-QT
Output:
12V
Current:
10A
Product # MCOTS-C-28-12-QT Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005277 Rev. D 02/04/13
Page 13
2.200 ±.020 [ 55.88 ±0.5 ]
1.536 ±.020 [ 39.01 ±0.5 ]
.01 [0.2]
OVERALL HEIGHT
.500 ±.025
[12.7 ±0.63]
.18
[ 4.6 ]
SEE NOTE 5 .15 [ 3.8 ]
.30 [ 7.6 ]
.45 [ 11.4 ]
.60 [ 15.2 ]
8
7
6
1
2
3
.30 [ 7.6 ]
.60 [ 15.2 ]
2.386
2.00
[ 50.8 ]
±.020
[ 60.6 ±0.5 ]
BOTTOMSIDE CLEARANCE
±.020.010
[0.51 0.25]
1.30
[ 33 ]
.70
[ 17.8 ]
.800 ±.020
[ 20.32 ±0.5 ]
2.07
[ ]
.13
[ 3.2 ]
1
.02 [ 0.6 ]
.183 ±.020
[ 4.65 ±0.5 ]
.36 [9.1]
1.01 [25.7]
1.66
[ 42.2 ]
TOP VIEW BOTTOM VIEW
52.5
5
4
R .065
1.65[ ]
Mechanical Drawing – Flanged Thermal Design Option
NOTES
1Applied torque per screw should not exceed 5in-lb (3in-lb
recommended).
2Baseplate flatness tolerance is 0.01" (.2mm) TIR for surface.
3Pins 1-3, 5-7 are 0.040" (1.02mm) diameter, with 0.080" (2.03mm)
diameter standoff shoulders.
4Pins 4 and 8 are 0.062" (1.57mm) diameter with 0.100" (2.54mm)
diameter standoff shoulders.
5Other pin extension lengths available.
6All Pins: Material - Copper Alloy; Finish - Matte Tin over Nickel plate
7Weight: 3.12 oz (88.5 g) typical
8Undimensioned components are shown for visual reference only.
9All dimensions in inches (mm)
Tolerances: x.xx +/-0.02 in. (x.x +/-0.5mm)
x.xxx +/-0.010 in. (x.xx +/-0.25mm)
10 Workmanship: Meets or exceeds IPC-A610 Class II
11 Recommended pin length is 0.03” (0.76mm) greater than the PCB
thickness.
12 A thermal interface material is required to assure proper heat
transfer from the flanged baseplate to the cooling surface. Thermal
grease, conductive pads, compounds, and other similar products are
available from many heatsink manufacturers.
PIN DESIGNATIONS - CONVERTER
Pin Name Function
1 Vin(+) Positive input voltage
2 ON/OFF TTL input to turn converter on and off,
referenced to Vin(–), with internal pull up.
3 IN RTN Input return
4 OUT RTN Output return
5 SENSE(–) Negative remote sense1
6 TRIM Output voltage trim2
7 SENSE(+) Positive remote sense3
8 Vout(+) Positive output voltage
Notes:
1) SENSE(–) should be connected to Vout(–) either remotely or
at the converter.
2) Leave TRIM pin open for nominal output voltage.
3) SENSE(+) should be connected to Vout(+) either remotely or
at the converter.
Technical Specification
MCOTS-C-28-12-QT
Output:
12V
Current:
10A
Product # MCOTS-C-28-12-QT Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005277 Rev. D 02/04/13
Page 14
Mil-COTS DC/DC Converter and Filter Screening
Screening Process Description S-Grade M-Grade
Baseplate Operating Temperature -55˚C to +100˚C -55˚C to +100˚C
Storage Temperature -65˚C to +135˚C -65˚C to +135˚C
Pre-Cap Inspection IPC-610, Class III ● ●
Temperature Cycling Method 1010, Condition B, 10
Cycles ●
Burn-In 100˚C Baseplate 12 Hours 96 Hours
Final Electrical Test 100% 25˚C -55˚C, +25˚C, +100˚C
Final Visual Inspection MIL-STD-2008 ● ●
Mil-COTS Qualication
Test Name Details # Tested
(# Failed)
Consistent with
MIL-STD-883F
Method
Consistent with
MIL-STD-883F
Method 5005
Life Testing
Visual, mechanical and electrical
testing before, during and after 1000
hour burn-in @ full load
15
(0) Method 1005.8
Shock-Vibration
Visual, mechanical and electrical
testing before, during and after shock
and vibration tests
5
(0)
MIL-STD-202, Methods
201A & 213B
Humidity +85˚C, 85% RH, 1000 hours, 2
minutes on/6 hours off
8
(0) Method 1004.7
Temperature Cycling 500 cycles of -55˚C to +100˚C (30
minute dwell at each temperature
10
(0) Method 1010.8 Condition A
Solderability 15 pins 15
(0) Method 2003
DMT -65˚C to +110˚C across full line and
load specications in 5˚C steps
7
(0)
Altitude 70,000 feet (21 km), see Note 2
(0)
Note: A conductive cooling design is generally needed for high altitude applications because of naturally poor convective
cooling at rare atmospheres.
Technical Specification
MCOTS-C-28-12-QT
Output:
12V
Current:
10A
Product # MCOTS-C-28-12-QT Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005277 Rev. D 02/04/13
Page 15
Warranty
SynQor offers a two (2) year limited warranty. Complete warranty infor-
mation is listed on our website or is available upon request from SynQor.
Information furnished by SynQor is believed to be accurate and reliable.
However, no responsibility is assumed by SynQor for its use, nor for any
infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any
patent or patent rights of SynQor.
Contact SynQor for further information:
Phone: 978-849-0600
Toll Free: 888-567-9596
Fax: 978-849-0602
E-mail: mqnbofae@synqor.com
Web:
www.synqor.com
Address: 155 Swanson Road
Boxborough, MA 01719
USA
Example MCOTS-C-28-12-QT-N-S
Not all combinations make valid part numbers, please contact SynQor for availability. See
product summary page
for details.
APPLICATION NOTES
A variety of application notes and technical white papers can be downloaded
in pdf format from our website.
Ordering Information/ Part Numbering
PATENTS
SynQor holds the following U.S. patents, one or more of which apply to
each product listed in this document. Additional patent applications may
be pending or led in the future.
5,999,417 6,222,742 6,545,890 6,577,109 6,594,159 6,731,520
6,894,468 6,896,526 6,927,987 7,050,309 7,072,190 7,085,146
7,119,524 7,269,034 7,272,021 7,272,023 7,558,083 7,564,702
7,765,687 7,787,261 8,023,290 8,149,597
Family Product Input
Voltage
Output
Voltage Package Thermal
Design
Screening
Level Options
MCOTS C: Converter
28: 16-40V
28V: 9-40V
28VE: 9-70V
48: 34-75V
270: 155-425V
1R8:
3R3:
05:
07:
12:
15:
24:
28:
48:
1.8V
3.3V
5V
7V
12V
15V
24V
28V
48V
QT:Quarter
Brick
N:
F:
Normal
Threaded
Flanged
S: S-Grade
M: M-Grade
[ ]: Standard
Feature