LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 Negative Voltage Hot Swap Controllers FEATURES n n n n n n n n DESCRIPTION Allows Safe Board Insertion and Removal from a Live - 48V Backplane Floating Topology Permits Very High Voltage Operation Current Limit With Circuit Breaker Timer Fast Response Time Limits Peak Fault Current Programmable Soft-Start Current Limit Programmable Timer with Drain Voltage Accelerated Response 1% Undervoltage/Overvoltage Threshold (LTC4252C) Improved Ruggedness Shunt Regulator Adjustable Undervoltage/Overvoltage Protection LTC4252B-1/LTC4252C-1: Latch Off After Fault LTC4252B-2/LTC4252C-2: Automatic Retry After Fault Available in 8-Pin and 10-Pin MSOP Packages APPLICATIONS n n n n n n n Hot Board Insertion Electronic Circuit Breaker - 48V Distributed Power Systems Negative Power Supply Control Central Office Switching High Availability Servers ATCA The LTC(R)4252 negative voltage Hot SwapTM controller allows a board to be safely inserted and removed from a live backplane. Output current is controlled by three stages of current limiting: a timed circuit breaker, active current limiting and a fast feedforward path that limits peak current under worst-case catastrophic fault conditions. Adjustable undervoltage and overvoltage detectors disconnect the load whenever the input supply exceeds the desired operating range. The LTC4252's supply input is shunt regulated, allowing safe operation with very high supply voltages. A multifunction timer delays initial startup and controls the circuit breaker's response time. The circuit breaker's response time is accelerated by sensing excessive MOSFET drain voltage, keeping the MOSFET within its safe operating area (SOA). An adjustable softstart circuit controls MOSFET inrush current at start-up. The LTC4252-2 provides automatic retry after a fault. The LTC4252C-1/LTC4252C-2 feature tight 1% undervoltage/ overvoltage threshold accuracy. The LTC4252 is available in either an 8-pin or 10-pin MSOP. The LTC4252B and LTC4252C improve the ruggedness of the shunt regulator in the LTC4252 and LTC4252A. L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and Hot Swap is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. TYPICAL APPLICATION Start-Up Behavior -48V/2.5A Hot Swap Controller -48RTN CIN 1F DIN DDZ13B** -48RTN (SHORT PIN) R1 402k 1% R3 5.1k PWRGD UV DRAIN C1 10nF SS * VOUT Q1 IRF530S GATE VEE SENSE CSS 68nF SENSE 2.5A/DIV RD 1M RC 10 CC 18nF RS 0.02 4252B12 TA01 * M0C207 **DIODES, INC GATE 5V/DIV LOAD EN OV TIMER CT 0.33F CL 100F VIN LTC4252B-1 R2 32.4k 1% -48V + RIN 3x 1.8k IN SERIES 1/4W EACH RECOMMENDED FOR HARSH ENVIRONMENTS VOUT 20V/DIV PWRGD 10V/DIV 1ms/DIV 4252B12 TA01a 4252b12f 1 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 ABSOLUTE MAXIMUM RATINGS All Voltages Referred to VEE (Note 1) Current into VIN (100s Pulse)..............................100mA VIN, DRAIN Pin Minimum Voltage......................... - 0.3V Input/Output Pins (Except SENSE and DRAIN) Voltage........... -0.3V to 16V SENSE Pin Voltage..................................... -0.6V to 16V Current Out of SENSE Pin (20s Pulse) ........... -200mA Current into DRAIN Pin (100s Pulse)....................20mA Maximum Junction Temperature........................... 125C Operating Temperature Range LTC4252BC-1/LTC4252BC-2 LTC4252CC-1/LTC4252CC-2..................... 0C to 70C LTC4252BI-1/LTC4252BI-2 LTC4252CI-1/LTC4252CI-2.................. -40C to 85C Storage Temperature Range................... -65C to 150C Lead Temperature (Soldering, 10 sec).................... 300C PIN CONFIGURATION TOP VIEW TOP VIEW VIN SS SENSE VEE 1 2 3 4 8 7 6 5 1 2 3 4 5 VIN PWRGD SS SENSE VEE TIMER UV/OV DRAIN GATE MS8 PACKAGE 8-LEAD PLASTIC MSOP 10 9 8 7 6 TIMER UV OV DRAIN GATE MS PACKAGE 10-LEAD PLASTIC MSOP TJMAX = 125C, JA = 160C/W TJMAX = 125C, JA = 160C/W ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL LTC4252BCMS8-1#PBF LTC4252BCMS8-2#PBF PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC4252BCMS8-1#TRPBF LTGDX 8-Lead Plastic MSOP 0C to 70C LTC4252BCMS8-2#TRPBF LTGDZ 8-Lead Plastic MSOP 0C to 70C LTC4252BIMS8-1#PBF LTC4252BIMS8-1#TRPBF LTGDX 8-Lead Plastic MSOP -40C to 85C LTC4252BIMS8-2#PBF LTC4252BIMS8-2#TRPBF LTGDZ 8-Lead Plastic MSOP -40C to 85C LTC4252BCMS-1#PBF LTC4252BCMS-1#TRPBF LTGDY 10-Lead Plastic MSOP 0C to 70C LTC4252BCMS-2#PBF LTC4252BCMS-2#TRPBF LTGFB 10-Lead Plastic MSOP 0C to 70C LTC4252BIMS-1#PBF LTC4252BIMS-1#TRPBF LTGDY 10-Lead Plastic MSOP -40C to 85C LTC4252BIMS-2#PBF LTC4252BIMS-2#TRPBF LTGFB 10-Lead Plastic MSOP -40C to 85C LTC4252CCMS-1#PBF LTC4252CCMS-1#TRPBF LTGFC 10-Lead Plastic MSOP 0C to 70C LTC4252CCMS-2#PBF LTC4252CCMS-2#TRPBF LTGFD 10-Lead Plastic MSOP 0C to 70C LTC4252CIMS-1#PBF LTC4252CIMS-1#TRPBF LTGFC 10-Lead Plastic MSOP -40C to 85C LTC4252CIMS-2#PBF LTC4252CIMS-2#TRPBF LTGFD 10-Lead Plastic MSOP -40C to 85C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 4252b12f 2 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 2) SYMBOL PARAMETER CONDITIONS VZ VIN - VEE Zener Voltage IIN = 2mA l LTC4252B-1/-2 MIN TYP MAX LTC4252C-1/-2 MIN TYP MAX 11.5 11.5 13 14.5 5 13 14.5 5 UNITS V rZ VIN - VEE Zener Dynamic Impedance IIN = 2mA to 30mA IIN VIN Supply Current UV = OV = 4V, VIN = (VZ - 0.3V) 0.8 2 0.9 2 mA VLKO VIN Undervoltage Lockout Coming Out of UVLO (Rising VIN) 9.2 11.5 9 10 V 55 mV VLKH VIN Undervoltage Lockout Hysteresis VCB Circuit Breaker Current Limit Voltage VCB = (VSENSE - VEE) 40 50 60 VACL Analog Current Limit Voltage VACL = (VSENSE - VEE), SS = Open or 2.2V 80 100 120 VACL/ VCB Analog Current Limit Voltage/ Circuit Breaker Voltage VACL = (VSENSE - VEE), SS = Open or 1.4V VFCL Fast Current Limit Voltage VFCL = (VSENSE - VEE) After End of SS Timing Cycle VSS SS Voltage RSS SS Output Impedance ISS SS Pin Current VOS 1 150 300 50 V mV 1.05 1.20 1.38 V/V 150 200 300 mV 2.2 1.4 V 50 k UV = OV = 4V, VSENSE = VEE, VSS = 0V (Sourcing) 22 28 A UV = OV = 0V, VSENSE = VEE, VSS = 2V (Sinking) 28 28 mA 10 10 mV 0.05 0.05 V/V Analog Current Limit Offset Voltage GATE Pin Output Current 0.5 45 100 VACL+VOS/ Ratio (VACL + VOS) to SS Voltage VSS IGATE 200 UV = OV = 4V, VSENSE = VEE, VGATE = 0V (Sourcing) 40 58 80 40 58 80 A UV = OV = 4V, VSENSE - VEE = 0.15V, VGATE = 3V (Sinking) 17 17 mA UV = OV = 4V, VSENSE - VEE = 0.3V, VGATE = 1V (Sinking) 190 190 mA VGATE External MOSFET Gate Drive VGATE - VEE, IIN = 2mA VGATEH Gate High Threshold VGATEH = VIN - VGATE, IIN = 2mA, for PWRGD Status (MS Only) VGATEL Gate Low Threshold (Before Gate Ramp-Up) 10 12 VZ 10 12 VZ V 2.8 2.8 V 0.5 0.5 V VUVHI UV Pin Threshold HIGH 3.075 VUVLO UV Pin Threshold LOW 2.775 3.225 3.375 V 2.925 3.075 V VUV UV Pin Threshold Low-to-High Transition VUVHST UV Pin Hysteresis ( for LTC4252C Only) VOVHI OV Pin Threshold HIGH VOVLO OV Pin Threshold LOW VOV OV Pin Threshold Low-to-High Transition VOVHST OV Pin Hysteresis ( for LTC4252C Only) 600 ISENSE SENSE Pin Input Current UV = OV = 4V, VSENSE = 50mV -15 -30 IINP UV, OV Pin Input Current UV = OV = 4V 0.1 1 VTMRH TIMER Pin Voltage High Threshold 4 4 V VTMRL TIMER Pin Voltage Low Threshold 1 1 V 300 5.85 6.15 6.45 5.25 5.55 5.85 3.05 3.08 3.11 V 292 324 356 mV V V 5.04 5.09 5.14 V 82 102 122 mV -15 -30 A 0.1 1 A 4252b12f 3 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 2) LTC4252B-1/-2 MIN TYP MAX LTC4252C-1/-2 MIN TYP MAX Timer On (Initial Cycle/Latchoff/ Shutdown Cooling, Sourcing), VTMR = 2V 5.8 5.8 A Timer Off (Initial Cycle, Sinking), VTMR = 2V 28 28 mA Timer On (Circuit Breaker, Sourcing, IDRN = 0A), VTMR = 2V 230 230 A Timer On (Circuit Breaker, Sourcing, IDRN = 50A), VTMR = 2V 630 630 A Timer Off (Circuit Breaker/ Shutdown Cooling, Sinking), VTMR = 2V 5.8 5.8 A Timer On (Circuit Breaker with IDRN = 50A) 8 8 2.385 SYMBOL PARAMETER CONDITIONS ITMR TIMER Pin Current ITMRACC/ [(ITMR at IDRN = 50A) - (ITMR at IDRN = 0A)]/IDRN IDRN VDRNL DRAIN Pin Voltage Low Threshold For PWRGD Status (MS Only) 2.385 IDRNL DRAIN Leakage Current VDRAIN = 5V (4V for LTC4252C) 0.1 VDRNCL DRAIN Pin Clamp Voltage IDRN = 50A VPGL PWRGD Output Low Voltage IPG = 1.6mA (MS Only) IPG = 5mA (MS Only) IPGH PWRGD Pull-Up Current VPWRGD = 0V (Sourcing) (MS Only) tSS SS Default Ramp Period SS Pin Floating, VSS Ramps from 0.2V to 2V 1 0.1 0.2 0.4 1.1 58 80 7 40 V 1 A 0.2 0.4 1.1 V V 58 80 A 180 SS Pin Floating, VSS Ramps from 0.1V to 0.9V A/A 6 40 UNITS V s 230 s tPLLUG UV Low to Gate Low 0.4 0.4 s tPHLOG OV High to Gate Low 0.4 0.4 s Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to VEE unless otherwise specified. 4252b12f 4 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 TYPICAL PERFORMANCE CHARACTERISTICS 14.5 VZ vs Temperature 10 IIN = 2mA rZ vs Temperature 2000 IIN = 2mA 1800 9 14.0 1400 7 1200 IIN (A) rZ () VZ (V) 13.0 6 1000 5 400 3 12.0 -55 -35 -15 200 2 -55 -35 -15 5 25 45 65 85 105 125 TEMPERATURE (C) 800 600 4 12.5 VIN = (VZ - 0.3V) 1600 8 13.5 IIN vs Temperature 0 -55 -35 -15 5 25 45 65 85 105 125 TEMPERATURE (C) 4252B12 G01 4252B12 G02 4252B12 G03 Undervoltage Lockout VLKO vs Temperature IIN vs VIN Undervoltage Lockout Hysteresis VLKH vs Temperature 12.0 1000 5 25 45 65 85 105 125 TEMPERATURE (C) 1.5 11.5 1.3 11.0 100 10 0.1 2 4 6 9.5 9.0 125C 85C 25C -40C 0 10.0 8.0 -55 -35 -15 8 10 12 14 16 18 20 22 VIN (V) 120 58 5 25 45 65 95 105 125 TEMPERATURE (C) 4252B12 G06 Analog Current Limit Voltage VACL vs Temperature Fast Current Limit Voltage VFCL vs Temperature 300 115 56 275 110 54 52 VACL (mV) VCB (mV) 0.5 -55 -35 -15 5 25 45 65 85 105 125 TEMPERATURE (C) 4252B12 G05 Circuit Breaker Current Limit Voltage VCB vs Temperature 50 48 46 250 105 100 95 225 200 90 44 175 85 42 40 -55 -35 -15 0.9 0.7 4252B12 G04 60 1.1 8.5 VFCL (mV) 1 VLKH (V) VLKO (V) IIN (mA) 10.5 5 25 45 65 85 105 125 TEMPERATURE (C) 4252B12 G07 80 -55 -35 -15 5 25 45 65 85 105 125 TEMPERATURE (C) 4252B12 G08 150 -55 -35 -15 5 25 45 65 85 105 125 TEMPERATURE (C) 4252B12 G09 4252b12f 5 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 TYPICAL PERFORMANCE CHARACTERISTICS VSS vs Temperature RSS vs Temperature 2.40 2.35 2.30 45 108 40 106 35 104 2.20 2.15 100 98 5 92 2.00 -55 -35 -15 90 -55 -35 -15 5 25 45 65 85 105 125 TEMPERATURE (C) 20 10 94 2.05 25 15 96 2.10 UV = OV = VSENSE = VEE IIN = 2mA VSS = 2V 30 102 ISS (mA) RSS (k) 2.25 VSS (V) ISS (Sinking) vs Temperature 110 0 -55 -35 -15 5 25 45 65 85 105 125 TEMPERATURE (C) 5 25 45 65 85 105 125 TEMPERATURE (C) 4252B12 G11 4252B12 G10 VOS vs Temperature 4252B12 G12 (VACL + VOS)/VSS vs Temperature 70 IGATE (Sourcing) vs Temperature 0.060 10.8 0.058 10.6 0.056 UV/0V = 4V TIMER = 0V 65 VSENSE = VEE VGATE = 0V 0.054 60 10.4 VOS (mV) 10.2 10.0 9.8 9.6 0.052 0.050 0.048 0.044 9.2 0.042 5 25 45 65 85 105 125 TEMPERATURE (C) 45 0.040 -55 -35 -15 400 350 300 IGATE (mA) IGATE (mA) 10 5 5 25 45 65 85 105 125 TEMPERATURE (C) 4252B12 G16 14.5 13.0 250 200 150 12.5 12.0 11.5 100 11.0 50 10.5 0 -55 -35 -15 VGATE vs Temperature UV/0V = 4V 14.0 TIMER = 0V VSENSE = VEE 13.5 UV/0V = 4V TIMER = 0V VSENSE - VEE = 0.3V VGATE = 1V VGATE (V) UV/0V = 4V TIMER = 0V VSENSE - VEE = 0.15V VGATE = 3V 20 0 -55 -35 -15 4252B12 G15 IGATE (FCL, Sinking) vs Temperature 15 5 25 45 65 85 105 125 TEMPERATURE (C) 4252B12 G14 IGATE (ACL, Sinking) vs Temperature 25 40 -55 -35 -15 5 25 45 65 85 105 125 TEMPERATURE (C) 4252B12 G13 30 55 50 0.046 9.4 9.0 -55 -35 -15 IGATE (A) (VACL + VOS) / VSS (V/V) 11.0 5 25 45 65 85 105 125 TEMPERATURE (C) 4252B12 G17 10.0 -55 -35 -15 5 25 45 65 85 105 125 TEMPERATURE (C) 4252B12 G18 4252b12f 6 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 TYPICAL PERFORMANCE CHARACTERISTICS VGATEH vs Temperature 3.6 VGATEL vs Temperature 3.0 0.5 VGATEL (V) VGATEH = VIN - VGATE, IIN = 2mA (MS ONLY) 2.8 2.6 0.3 0.2 2.2 0.1 5 25 45 65 85 105 125 TEMPERATURE (C) OV Threshold vs Temperature 6.45 -10 2.975 VUVL 2.775 -55 -35 -15 5 25 45 65 85 105 125 TEMPERATURE (C) 4252B12 G21 ISENSE vs Temperature ISENSE vs (VSENSE - VEE) 0.01 -14 0.1 5.85 VOVL 5.45 -18 -20 -22 -24 5.25 VOV -26 5.05 -28 4.85 -55 -35 -15 UV/0V = 4V TIMER = 0V GATE = HIGH VSENSE - VEE = 50mV -30 -55 -35 -15 5 25 45 65 85 105 125 TEMPERATURE (C) 4252B12 G22 10 9 VTMRH 3.0 6 ITMR (A) 7 2.5 2.0 1.0 0 -55 -35 -15 40 5 4 4252B12 G25 0 -55 -35 -15 TIMER = 2V 45 35 30 25 20 15 1 5 25 45 65 85 105 125 TEMPERATURE (C) 2.0 ITMR (Initial Cycle, Sinking) vs Temperature 50 2 0.5 1.5 4252B12 G24 TIMER = 2V 3 VTMRL UV/0V = 4V TIMER = 0V GATE = HIGH TA = 25C 1000 -1.5 -1.0 -0.5 0 0.5 1.0 (VSENSE - VEE) (V) 8 3.5 1.5 5 25 45 65 85 105 125 TEMPERATURE (C) ITMR (Initial Cycle, Sourcing) vs Temperature 5.0 4.0 10 4252B12 G23 TIMER Threshold vs Temperature 4.5 1.0 100 ITMR (mA) 5.65 -ISENSE (mA) -16 ISENSE (A) OV THRESHOLD (V) VUV 3.075 -12 VOVH 6.05 TIMER THRESHOLD (V) 3.175 4252B12 G20 4252B12 G19 6.25 VUVH 2.875 0 -55 -35 -15 5 25 45 65 85 105 125 TEMPERATURE (C) 3.275 0.4 2.4 2.0 -55 -35 -15 UV Threshold vs Temperature 3.375 UV THRESHOLD (V) 3.2 UV/0V = 4V 0.7 TIMER = 0V GATE THRESHOLD 0.6 BEFORE RAMP-UP 3.4 VGATEH (V) 0.8 5 25 45 65 85 105 125 TEMPERATURE (C) 4252B12 G26 10 -55 -35 -15 5 25 45 65 85 105 125 TEMPERATURE (C) 4252B12 G27 4252b12f 7 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 TYPICAL PERFORMANCE CHARACTERISTICS ITMR (Circuit Breaker, Sourcing) vs Temperature 280 ITMR (Circuit Breaker, IDRN = 50A, Sourcing) vs Temperature 690 TIMER = 2V IDRN = 0A 670 260 ITMR (Cooling Cycle, Sinking) vs Temperature 10 TIMER = 2V IDRN = 50A 8 220 7 630 ITMR (A) ITMR (A) ITMR (A) 650 240 610 5 25 45 65 85 105 125 TEMPERATURE (C) 8.8 TIMER ON (CIRCUIT BREAKING, IDRN = 50A) 1 8.4 8.2 8.0 7.8 7.6 5 25 45 65 85 105 125 TEMPERATURE (C) 4252B12 G31 FOR PWRGD STATUS (MS ONLY) 7.8 2.55 IDRN = 50A 7.0 6.8 0.5 6.2 5 25 45 65 85 105 125 TEMPERATURE (C) 4252B12 G34 8 10 VDRAIN (V) 12 6.0 -55 -35 -15 14 16 5 25 45 65 85 105 125 TEMPERATURE (C) 4252B12 G35 IPG = 10mA 1.5 1.0 6.4 2.25 6 (MS ONLY) 2.0 7.2 6.6 2.30 4 2.5 VPGL (V) VDRNCL (V) VDRNL (V) 2.35 2 VPGL vs Temperature 3.0 7.4 2.40 0 4252B12 G33 7.6 2.50 2.20 -55 -35 -15 0.00001 VDRNCL vs Temperature 8.0 2.45 125C 85C 25C -40C 4252B12 G32 VDRNL vs Temperature 2.60 0.01 0.0001 7.0 -55 -35 -15 10 0.1 0.001 7.2 1 IIN = 2mA 10 7.4 0.1 IDRN (mA) IDRN vs VDRAIN 100 IDRN (mA) ITMRACC/IDRN (A/A) ITMR (mA) 8.6 1 5 25 45 65 85 105 125 TEMPERATURE (C) 4252B12 G30 ITMRACC/IDRN vs Temperature 9.0 0.01 0 -55 -35 -15 5 25 45 65 85 105 125 TEMPERATURE (C) 4252B12 G29 ITMR vs IDRN 0.1 0.001 4 1 550 -55 -35 -15 4252B12 G28 10 5 2 570 180 -55 -35 -15 6 3 590 200 TIMER = 2V 9 0 -55 -35 -15 IPG = 5mA IPG = 1.6mA 5 25 45 65 85 105 125 TEMPERATURE (C) 4252B12 G36 4252b12f 8 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 TYPICAL PERFORMANCE CHARACTERISTICS 62 220 VPWRGD = 0V (MS ONLY) 210 60 200 59 190 tSS (s) IPGH (A) 61 58 170 56 160 5 25 45 65 85 105 125 TEMPERATURE (C) 4252B12 G37 0.8 SS PIN FLOATING, VSS RAMPS FROM 0.2V TO 2V 0.7 0.6 180 57 55 -55 -35 -15 tPLLUG and tPHLOG vs Temperature tSS vs Temperature DELAY (s) IPGH vs Temperature 150 -55 -35 -15 0.4 0.3 tPLLUG tPHLOG 0.2 0.1 5 25 45 65 85 105 125 TEMPERATURE (C) 4252B12 G38 PIN FUNCTIONS 0.5 0 -55 -35 -15 5 25 45 65 85 105 125 TEMPERATURE (C) 4252B12 G39 (MS/MS8) VIN (Pin 1/Pin 1): Positive Supply Input. Connect this pin to the positive side of the supply through a dropping resistor. A shunt regulator clamps VIN at 13V. An internal undervoltage lockout (UVLO) circuit holds GATE low until the VIN pin is greater than VLKO, overriding UV and OV. If UV is high, OV is low and VIN comes out of UVLO, TIMER starts an initial timing cycle before initiating a GATE rampup. If VIN drops below approximately 8.2V, GATE pulls low immediately. PWRGD (Pin 2/Not Available): Power Good Status Output (MS only). At start-up, PWRGD latches low if DRAIN is below 2.385V and GATE is within 2.8V of VIN. PWRGD status is reset by UV, VIN (UVLO) or a circuit breaker fault timeout. This pin is internally pulled high by a 58A current source. SS (Pin 3/Pin 2): Soft-Start Pin. This pin is used to ramp inrush current during start up, thereby effecting control over di/dt. A 20x attenuated version of the SS pin voltage is presented to the current limit amplifier. This attenuated voltage limits the MOSFET's drain current through the sense resistor during the soft-start current limiting. At the beginning of a start-up cycle, the SS capacitor (CSS) is ramped by a 22A (28A for the LTC4252C) current source. The GATE pin is held low until SS exceeds 20 * VOS = 0.2V. SS is internally shunted by a 100k resistor (RSS) which limits the SS pin voltage to 2.2V (50k resistor and 1.4V for the LTC4252C). This corresponds to an analog current limit SENSE voltage of 100mV (60mV for the LTC4252C). If the SS capacitor is omitted, the SS pin ramps up in about 180s. The SS pin is pulled low under any of the following conditions: in UVLO, in an undervoltage condition, in an overvoltage condition, during the initial timing cycle or when the circuit breaker fault times out. SENSE (Pin 4/Pin 3): Circuit Breaker/Current Limit Sense Pin. Load current is monitored by a sense resistor RS connected between SENSE and VEE, and controlled in three steps. If SENSE exceeds VCB (50mV), the circuit breaker comparator activates a (230A + 8 * IDRN) TIMER pull-up current. If SENSE exceeds VACL, the analog current limit amplifier pulls GATE down to regulate the MOSFET current at VACL/RS. In the event of a catastrophic short-circuit, SENSE may overshoot. If SENSE reaches VFCL (200mV), the fast current limit comparator pulls GATE low with a strong pull-down. To disable the circuit breaker and current limit functions, connect SENSE to VEE. 4252b12f 9 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 PIN FUNCTIONS (MS/MS8) VEE (Pin 5/Pin 4): Negative Supply Voltage Input. Connect this pin to the negative side of the power supply. GATE (Pin 6/Pin 5): N-Channel MOSFET Gate Drive Output. This pin is pulled high by a 58A current source. GATE is pulled low by invalid conditions at VIN (UVLO), UV, OV, or a circuit breaker fault timeout. GATE is actively servoed to control the fault current as measured at SENSE. A compensation capacitor at GATE stabilizes this loop. A comparator monitors GATE to ensure that it is low before allowing an initial timing cycle, GATE ramp-up after an overvoltage event or restart after a current limit fault. During GATE start-up, a second comparator detects if GATE is within 2.8V of VIN before PWRGD is set (MS package only). DRAIN (Pin 7/Pin 6): Drain Sense Input. Connecting an external resistor, RD, between this pin and the MOSFET's drain (VOUT) allows voltage sensing below 6.15V (5V for LTC4252C) and current feedback to TIMER. A comparator detects if DRAIN is below 2.385V and together with the GATE high comparator sets the PWRGD flag. If VOUT is above VDRNCL, DRAIN clamps at approximately VDRNCL. The current through RD is internally multiplied by 8 and added to TIMER's 230A pull-up current during a circuit breaker fault cycle. This reduces the fault time and MOSFET heating. OV (Pin 8/Pin 7): Overvoltage Input. The active high threshold at the OV pin is set at 6.15V with 0.6V hysteresis. If OV > 6.15V, GATE pulls low. When OV returns below 5.55V, GATE start-up begins without an initial timing cycle. The LTC4252C OV pin is set at 5.09V with 102mV hysteresis. If OV > 5.09V, GATE pulls low. When OV returns below 4.988V, GATE start-up begins without an initial timing cycle. If an overvoltage condition occurs in the middle of an initial timing cycle, the initial timing cycle is restarted after the overvoltage condition goes away. An overvoltage condition does not reset the PWRGD flag. The internal UVLO at VIN always overrides OV. A 1nF to 10nF capacitor at OV prevents transients and switching noise from affecting the OV thresholds and prevents glitches at the GATE pin. UV (Pin 9/Pin 7): Undervoltage Input. The active low threshold at the UV pin is set at 2.925V with 0.3V hysteresis. If UV < 2.925V, PWRGD pulls high, both GATE and TIMER pull low. If UV rises above 3.225V, this initiates an initial timing cycle followed by GATE start-up. The LTC4252C UV pin is set at 3.08V with 324mV hysteresis. If UV < 2.756V, PWRGD pulls high, both GATE and TIMER pull low. If UV rises above 3.08V, this initiates an initial timing cycle followed by GATE start-up. The internal UVLO at VIN always overrides UV. A low at UV resets an internal fault latch. A 1nF to 10nF capacitor at UV prevents transients and switching noise from affecting the UV thresholds and prevents glitches at the GATE pin. TIMER (Pin 10/Pin 8): Timer Input. TIMER is used to generate an initial timing delay at start-up and to delay shutdown in the event of an output overload (circuit breaker fault). TIMER starts an initial timing cycle when the following conditions are met: UV is high, OV is low, VIN clears UVLO, TIMER pin is low, GATE is lower than VGATEL, SS < 0.2V, and VSENSE - VEE < VCB. A pull-up current of 5.8A then charges CT, generating a time delay. If CT charges to VTMRH (4V), the timing cycle terminates, TIMER quickly pulls low and GATE is activated. If SENSE exceeds 50mV while GATE is high, a circuit breaker cycle begins with a 230A pull-up current charging CT. If DRAIN is approximately 7V (6V for LTC4252C) during this cycle, the timer pull-up has an additional current of 8 * IDRN. If SENSE drops below 50mV before TIMER reaches 4V, a 5.8A pull-down current slowly discharges the CT. In the event that CT eventually integrates up to the VTMRH threshold, the circuit breaker trips, GATE quickly pulls low and PWRGD pulls high. The LTC4252-1 TIMER pin latches high with a 5.8A pull-up source. This latched fault is cleared by either pulling TIMER low with an external device or by pulling UV below VUVLO. The LTC4252-2 starts a shutdown cooling cycle following an overcurrent fault. This cycle consists of 4 discharging ramps and 3 charging ramps. The charging and discharging currents are 5.8A and TIMER ramps between its 1V and 4V thresholds. At the completion of a shutdown cooling cycle, the LTC4252-2 attempts a start-up cycle. 4252b12f 10 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 BLOCK DIAGRAM VIN - DRAIN VIN + 2.385V 8x VEE 6.15V (5V) 1x 1x 1x VIN 58A VEE PWRGD ** 6.15V (5.09V) VIN - 58A VEE GATE + OV * 2.8V VIN - - + 4V 5.8A + (-) LOGIC 230A VIN -+ + 2.925V (3.08V) VIN - VEE - (+) UV * + 0.5V TIMER + - VIN 1V 200mV - VEE 5.8A FCL + +- VEE VEE 22A (28A) + SS VOS = 10mV 95k (47.5k) 5k (2.5k) VEE ACL - VEE + RSS -+ CB VEE SENSE 50mV +- VEE - VEE 4252B12 BD *OV AND UV ARE TIED TOGETHER ON THE MS8 PACKAGE. OV AND UV ARE SEPARATE PINS ON THE MS PACKAGE ** ONLY AVAILABLE IN THE MS PACKAGE FOR COMPONENTS, CURRENT AND VOLTAGE WITH TWO VALUES, VALUES IN PARENTHESES REFER TO THE LTC4252C. VALUES WITHOUT PARENTHESES REFER TO THE LTC4252B 4252b12f 11 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 OPERATION Hot Circuit Insertion Interlock Conditions When circuit boards are inserted into a live backplane, the supply bypass capacitors can draw huge transient currents from the power bus as they charge. The flow of current damages the connector pins and glitches the power bus, causing other boards in the system to reset. The LTC4252 is designed to turn on a circuit board supply in a controlled manner, allowing insertion or removal without glitches or connector damage. A start-up sequence commences once these "interlock" conditions are met. The LTC4252 resides on a removable circuit board and controls the path between the connector and load or power conversion circuitry with an external MOSFET switch (see Figure 1). Both inrush control and short-circuit protection are provided by the MOSFET. A detailed schematic for the LTC4252C is shown in Figure 2. - 48V and -48RTN receive power through the longest connector pins and are the first to connect when the board is inserted. The GATE pin holds the MOSFET off during this time. UV and OV determine whether or not the MOSFET should be turned on based upon internal high accuracy thresholds and an external divider. UV and OV do double duty by also monitoring whether or not the connector is seated. The top of the divider detects -48RTN by way of a short connector pin that is the last to mate during the insertion sequence. -48RTN PLUG-IN BOARD + LTC4252 -48V LONG 2. The voltage at UV > VUVHI. 3. The voltage at OV < VOVLO. 4. The (SENSE - VEE) voltage is < 50mV (VCB). 5. The voltage at SS is < 0.2V (20 * VOS). Initial Start-Up LONG 1. The input voltage VIN exceeds VLKO (UVLO). + CLOAD - 7. The voltage at GATE is < 0.5V (VGATEL). The first three conditions are continuously monitored and the latter four are checked prior to initial timing or GATE ramp-up. Upon exiting an OV condition, the TIMER pin voltage requirement is inhibited. Details are described in the Applications Information, Timing Waveforms section. TIMER begins the start-up sequence by sourcing 5.8A into CT. If VIN, UV or OV falls out of range, the start-up cycle stops and TIMER discharges CT to less than 1V, then waits until the aforementioned conditions are once again met. If CT successfully charges to 4V, TIMER pulls low and both SS and GATE pins are released. GATE sources 58A (IGATE), charging the MOSFET gate and associated capacitance. The SS voltage ramp limits VSENSE to control the inrush current. PWRGD pulls active low when GATE is within 2.8V of VIN and DRAIN is lower than VDRNL. -48RTN + ISOLATED DC/DC CONVERTER MODULE 6. The voltage on the TIMER capacitor (CT) is < 1V (VTMRL). LOW VOLTAGE CIRCUITRY LONG DIN+ DDZ13B** SHORT - BACKPLANE R1 392k 1% RIN 3 x 1.8k IN SERIES 1/4W EACH CIN 1F Figure 1. Basic LTC4252 Hot Swap Topology R2 30.1k 1% -48V LONG + VIN OV UV LTC4252C-1 TIMER C1 10nF 4252B12 F01 CLOAD 100F SS CSS 68nF CT 0.68F VEE DRAIN SENSE GATE CC 10nF RS 0.02 **DIODES, INC RECOMMENDED FOR HARSH ENVIRONMENTS RC 10 Q1 IRF530S RD 1M 4252B12 F02 Figure 2.-48V, 2.5A Hot Swap Controller 4252b12f 12 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 OPERATION Two modes of operation are possible during the time the MOSFET is first turning on, depending on the values of external components, MOSFET characteristics and nominal design current. One possibility is that the MOSFET will turn on gradually so that the inrush into the load capacitance remains a low value. The output will simply ramp to -48V and the LTC4252 will fully enhance the MOSFET. A second possibility is that the load current exceeds the soft-start current limit threshold of [VSS(t)/20 - VOS]/RS. In this case the LTC4252 will ramp the output by sourcing soft-start limited current into the load capacitance. If the soft-start voltage is below 1.2V, the circuit breaker TIMER is held low. Above 1.2V, TIMER ramps up. It is important to set the timer delay so that, regardless of which start-up mode is used, the TIMER ramp is less than one circuit breaker delay time. If this condition is not met, the LTC42521 may shut down after one circuit breaker delay time whereas the LTC4252-2 may continue to autoretry. Board Removal If the board is withdrawn from the card cage, the UV and OV divider is the first to lose connection. This shuts off the MOSFET and commutates the flow of current in the connector. When the power pins subsequently separate, there is no arcing. Current Control Three levels of protection handle short-circuit and overload conditions. Load current is monitored by SENSE and resistor RS. There are three distinct thresholds at SENSE: 50mV for a timed circuit breaker function; 100mV for an analog current limit loop (60mV for the LTC4252C); and 200mV for a fast, feedforward comparator which limits peak current in the event of a catastrophic short-circuit. If, owing to an output overload, the voltage drop across RS exceeds 50mV, TIMER sources 230A into CT. CT eventually charges to a 4V threshold and the LTC4252 shuts off. If the overload goes away before CT reaches 4V and SENSE measures less than 50mV, CT slowly discharges (5.8A). In this way the LTC4252's circuit breaker function responds to low duty cycle overloads and accounts for fast heating and slow cooling characteristics of the MOSFET. Higher overloads are handled by an analog current limit loop. If the drop across RS reaches VACL, the current limiting loop servos the MOSFET gate and maintains a constant output current of VACL/RS. In current limit mode, VOUT typically rises and this increases MOSFET heating. If VOUT > VDRNCL, connecting an external resistor, RD, between VOUT and DRAIN allows the fault timing cycle to be shortened by accelerating the charging of the TIMER capacitor. The TIMER pull-up current is increased by 8 * IDRN. Note that because SENSE > 50mV, TIMER charges CT during this time and the LTC4252 will eventually shut down. Low impedance failures on the load side of the LTC4252 coupled with 48V or more driving potential can produce current slew rates well in excess of 50A/s. Under these conditions, overshoot is inevitable. A fast SENSE comparator with a threshold of 200mV detects overshoot and pulls GATE low much harder and hence much faster than the weaker current limit loop. The VACL/RS current limit loop then takes over and servos the current as previously described. As before, TIMER runs and shuts down the LTC4252 when CT reaches 4V. If CT reaches 4V, the LTC4252-1 latches off with a 5.8A pull-up current source whereas the LTC4252-2 starts a shutdown cooling cycle. The LTC4252-1 circuit breaker latch is reset by either pulling UV momentarily low or dropping the input voltage VIN below the internal UVLO threshold or pulling TIMER momentarily low with a switch. The LTC4252-2 retries after its shutdown cooling cycle. Although short-circuits are the most obvious fault type, several operating conditions may invoke overcurrent protection. Noise spikes from the backplane or load, input steps caused by the connection of a second, higher voltage supply, transient currents caused by faults on adjacent circuit boards sharing the same power bus or the insertion of non-hot-swappable products could cause higher than anticipated input current and temporary detection of an overcurrent condition. The action of TIMER and CT rejects these events allowing the LTC4252 to "ride out" temporary overloads and disturbances that could trip a simple current comparator and, in some cases, blow a fuse. 4252b12f 13 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 APPLICATIONS INFORMATION SHUNT REGULATOR Kelvin terminal as illustrated in Figure 3, keeping trace lengths between VIN, CIN, DIN and VEE as short as possible. A fast responding shunt regulator clamps the VIN pin to 13V (VZ). Power is derived from -48RTN by an external current limiting resistor, RIN. A 1F decoupling capacitor, CIN filters supply transients and contributes a short delay at start-up. INTERNAL UNDERVOLTAGE LOCKOUT (UVLO) A hysteretic comparator, UVLO, monitors VIN for undervoltage. The thresholds are defined by VLKO and its hysteresis, VLKH. When VIN rises above VLKO the chip is enabled; below (VLKO - VLKH) it is disabled and GATE is pulled low. The UVLO function at VIN should not be confused with the UV/OV pin(s). These are completely separate functions. To meet creepage requirements RIN may be split into two or more series connected units. This introduces a wider total spacing than is possible with a single component while at the same time ballasting the potential across the gap under each resistor. The LTC4252 is fundamentally a low voltage device that operates with -48V as its reference ground. To further protect against arc discharge into its pins, the area in and around the LTC4252 and all associated components should be free of any other planes such as chassis ground, return, or secondary-side power and ground planes. UV/OV COMPARATORS (LTC4252B) An UV hysteretic comparator detects undervoltage conditions at the UV pin, with the following thresholds: UV low-to-high (VUVHI) = 3.225V VIN may be biased with additional current up to 30mA to accommodate external loading such as the PWRGD optocoupler shown in Figure 23. As an alternative to running higher current, simply buffer VIN with an emitter follower as shown in Figure 3. Another method shown in Figure 19 cascodes the PWRGD output. UV high-to-low (VUVLO) = 2.925V An OV hysteretic comparator detects overvoltage conditions at the OV pin, with the following thresholds: OV low-to-high (VOVHI) = 6.150V OV high-to-low (VOVLO) = 5.550V VIN is rated handle 30mA within the thermal limits of the package, and is tested to survive a 100s, 100mA pulse. To protect VIN against damage from higher amplitude spikes, clamp VIN to VEE with a 13V Zener diode. Star connect VEE and all VEE-referred components to the sense resistor -48RTN The UV and OV trip point ratio is designed to match the standard telecom operating range of 43V to 82V when connected together as in the typical application. A divider (R1, R2) is used to scale the supply voltage. Using R1 = 402k RIN 10k 1/2W R4 22k -48RTN (SHORT PIN) 1 VIN R1 432k 1% 9 R2 4.75k 1% R3 38.3k 1% -48V DIN DDZ13B** 8 C2 10nF * M0C207 Q2: MMBT5551LT1 LTC4252B-1 UV PWRGD OV DRAIN 10 TIMER 3 CT SS 330nF CSS 68nF GATE VEE SENSE CIN 1F Q2 + LOAD R5 2.2k EN * 2 7 CL 100F RD 1M 6 Q1 IRF530S 4 5 **DIODES, INC RECOMMENDED FOR HARSH ENVIRONMENTS RC 10 CC 18nF 4252B12 F03 Figure 3. - 48V/2.5A Application with Different Input Operating Range 14 RS 0.02 4252b12f LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 APPLICATIONS INFORMATION and R2 = 32.4k gives a typical operating range of 43.2V to 82.5V. The undervoltage shutdown and overvoltage recovery thresholds are then 39.2V and 74.4V. 1% divider resistors are recommended to preserve threshold accuracy. OV low-to-high (VOV) = 5.09V OV high-to-low (VOV - VOVHST) = 4.988V The UV and OV trip point ratio is designed to match the standard telecom operating range of 43V to 71V when connected together as in Figure 2. A divider (R1, R2) is used to scale the supply voltage. Using R1 = 390k and R2 = 30.1k gives a typical operating range of 43V to 71V. The undervoltage shutdown and overvoltage recovery thresholds are then 38.5V and 69.6V respectively. 1% divider resistors are recommended to preserve threshold accuracy. The R1-R2 divider values shown in the Typical Application set a standing current of slightly more than 100A and define an impedance at UV/OV of 30k. In most applications, 30k impedance coupled with 300mV UV hysteresis makes the LTC4252B insensitive to noise. If more noise immunity is desired, add a 1nF to 10nF filter capacitor from UV/OV to VEE. The R1-R2 divider values shown in Figure 2 set a standing current of slightly more than 100A and define an impedance at UV/OV of 28k. In most applications, 28k impedance coupled with 324mV UV hysteresis makes the LTC4252C insensitive to noise. If more noise immunity is desired, add a 1nF to 10nF filter capacitor from UV/OV to VEE. Separate UV and OV pins are available in the 10-pin MS package and can be used for a different operating range such as 35.5V to 76V as shown in Figure 3. Other combinations are possible with different resistor arrangements. UV/OV COMPARATORS (LTC4252C) The UV and OV pins can be used for a wider operating range such as 35.5V to 76V as shown in Figure 4. Other combinations are possible with different resistor arrangements. A UV hysteretic comparator detects undervoltage conditions at the UV pin, with the following thresholds: UV low-to-high (VUV) = 3.08V UV high-to-low (VUV - VUVHST) = 2.756V UV/OV OPERATION An OV hysteretic comparator detects overvoltage conditions at the OV pin, with the following thresholds: -48RTN A low input to the UV comparator will reset the chip and pull the GATE and TIMER pins low. A low-to-high UV transition will initiate an initial timing sequence if the other interlock RIN 10k 1/2W R4 22k -48RTN (SHORT PIN) 1 VIN R1 464k 1% 9 R2 10k 1% R3 34k 1% -48V DIN DDZ13B** 8 10 LTC4252C-1 UV PWRGD OV DRAIN TIMER 3 CT SS 0.68F C2 10nF * M0C207 Q2: MMBT5551LT1 CSS 68nF GATE VEE SENSE CIN 1F Q2 + LOAD R5 2.2k EN * 2 7 CL 100F RD 1M 6 Q1 IRF530S 4 5 **DIODES, INC RECOMMENDED FOR HARSH ENVIRONMENTS RC 10 CC 10nF RS 0.02 4252B12 F04 Figure 4. - 48V/2.5A Application with Wider Input Operating Range 4252b12f 15 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 APPLICATIONS INFORMATION conditions are met. A high-to-low transition in the UV comparator immediately shuts down the LTC4252, pulls the MOSFET gate low and resets the latched PWRGD high. 4) Low impedance switch; resets the TIMER capacitor after an initial timing delay, in UVLO, in UV and in OV during initial timing. Overvoltage conditions detected by the OV comparator will also pull GATE low, thereby shutting down the load. However, it will not reset the circuit breaker TIMER, PWRGD flag or shutdown cooling timer. Returning the supply voltage to an acceptable range restarts the GATE pin if all the interlock conditions except TIMER are met. Only during the initial timing cycle does an OV condition reset the TIMER. For initial start-up, the 5.8A pull-up is used. The low impedance switch is turned off and the 5.8A current source is enabled when the interlock conditions are met. CT charges to 4V in a time period given by: DRAIN Connecting an external resistor, RD, to the dual function DRAIN pin allows VOUT sensing* without it being damaged by large voltage transients. Below 5V, negligible pin leakage allows a DRAIN low comparator to detect VOUT less than 2.385V (VDRNL). This condition, together with the GATE low comparator, sets the PWRGD flag. If VOUT > VDRNCL, the DRAIN pin is clamped at about VDRNCL and the current flowing in RD is given by: IDRN VOUT -VDRNCL RD (1) This current is scaled up 8 times during a circuit breaker fault and is added to the nominal 230A TIMER current. This accelerates the fault TIMER pull-up when the MOSFET's drain-source voltage exceeds VDRNCL and effectively shortens the MOSFET heating duration. TIMER The operation of the TIMER pin is somewhat complex as it handles several key functions. A capacitor CT is used at TIMER to provide timing for the LTC4252. Four different charging and discharging modes are available at TIMER: 1) A 5.8A slow charge; initial timing and shutdown cooling delay. 2) A (230A + 8 * IDRN) fast charge; circuit breaker delay. 3) A 5.8A slow discharge; circuit breaker "cool off" and shutdown cooling. t= 4V *CT 5.8A (2) When CT reaches 4V (VTMRH), the low impedance switch turns on and discharges CT. A GATE start-up cycle begins and both SS and GATE are released. CIRCUIT BREAKER TIMER OPERATION If the SENSE pin detects more than a 50mV drop across RS, the TIMER pin charges CT with (230A + 8 * IDRN). If CT charges to 4V, the GATE pin pulls low and the LTC42521 latches off while the LTC4252-2 starts a shutdown cooling cycle. The LTC4252-1 remains latched off until the UV pin is momentarily pulsed low or TIMER is momentarily discharged low by an external switch or VIN dips below UVLO and is then restored. The circuit breaker timeout period is given by: t= 4V *CT 230A +8 *IDRN (3) If VOUT < 5V, an internal PMOS device isolates any DRAIN pin leakage current, making IDRN = 0A in Equation (3). If VOUT > VDRNCL during the circuit breaker fault period, the charging of CT accelerates by 8 * IDRN of Equation (1). Intermittent overloads may exceed the 50mV threshold at SENSE, but, if their duration is sufficiently short, TIMER will not reach 4V and the LTC4252 will not shut the external MOSFET off. To handle this situation, the TIMER discharges CT slowly with a 5.8A pull-down whenever the SENSE voltage is less than 50mV. Therefore, any intermittent overload with VOUT > 5V and an aggregate duty cycle of *VOUT as viewed by the MOSFET; i.e., VDS. 4252b12f 16 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 APPLICATIONS INFORMATION NORMALIZED RESPONSE TIME (s/F) 10 SOFT-START IDRN = 0A Soft-start limits the inrush current profile during GATE start-up. Unduly long soft-start intervals can exceed the MOSFET's SOA rating if powering up into an active load. If SS floats, an internal current source ramps SS from 0V to 2.2V for the LTC4252B or 0V to 1.4V for the LTC4252C in about 230s. Connecting an external capacitor CSS from SS to ground modifies the ramp to approximate an RC response of: 1 t CT(F) = 4 [(235.8 + 8 * IDRN) * D - 5.8] 0.1 0.01 0 20 40 60 80 FAULT DUTY CYCLE (%) t -R * C SS SS VSS (t)VSS * 1-e 100 4252B12 F05 Figure 5. Circuit-Breaker Response Time 2.5% or more will eventually trip the circuit breaker and shut down the LTC4252. Figure 5 shows the circuit breaker response time in seconds normalized to 1F for IDRN = 0A. The asymmetric charging and discharging of CT is a fair gauge of MOSFET heating. The normalized circuit response time is estimated by 4 t = CT (F) ( 235.8+8 *IDRN ) *D-5.8 (4) SHUTDOWN COOLING CYCLE For the LTC4252-1 (latchoff version), TIMER latches high with a 5.8A pull-up after the circuit breaker fault TIMER reaches 4V. For the LTC4252-2 (automatic retry version), a shutdown cooling cycle begins if TIMER reaches the 4V threshold. TIMER starts with a 5.8A pull-down until it reaches the 1V threshold. Then, the 5.8A pull-up turns back on until TIMER reaches the 4V threshold. Four 5.8A pull-down cycles and three 5.8A pull-up cycles occur between the 1V and 4V thresholds, creating a time interval given by: tSHUTDOWN = 7 * 3V *CT 5.8A (5) At the 1V threshold of the last pull-down cycle, a GATE ramp-up is attempted. (6) An internal resistive divider (95k/5k for the LTC4252B or 47.5k/2.5k for the LTC4252C) scales VSS(t) down by 20 times to give the analog current limit threshold: VACL (t)= VSS (t) -VOS 20 (7) This allows the inrush current to be limited to VACL(t)/RS. The offset voltage, VOS (10mV), ensures CSS is sufficiently discharged and the ACL amplifier is in current limit before GATE start-up. SS is pulled low under any of the following conditions: in UVLO, in an undervoltage condition, in an overvoltage condition, during the initial timing cycle or when the circuit breaker fault times out. GATE GATE is pulled low to VEE under any of the following conditions: in UVLO, in an undervoltage condition, in an overvoltage condition, during the initial timing cycle or when the circuit breaker fault times out. When GATE turns on, a 58A current source charges the MOSFET gate and any associated external capacitance. VIN limits the gate drive to no more than 14.5V. Gate-drain capacitance (CGD) feedthrough at the first abrupt application of power can cause a gate-source voltage sufficient to turn on the MOSFET. A unique circuit pulls GATE low with practically no usable voltage at VIN 4252b12f 17 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 APPLICATIONS INFORMATION and eliminates current spikes at insertion. A large external gate-source capacitor is thus unnecessary for the purpose of compensating CGD. Instead, a smaller value ( 10nF) capacitor CC is adequate. CC also provides compensation for the analog current limit loop. GATE has two comparators: the GATE low comparator looks for < 0.5V threshold prior to initial timing or a GATE start-up cycle; the GATE high comparator looks for < 2.8V relative to VIN and, together with the DRAIN low comparator, sets PWRGD status during GATE startup. SENSE The SENSE pin is monitored by the circuit breaker (CB) comparator, the analog current limit (ACL) amplifier and the fast current limit (FCL) comparator. Each of these three measures the potential of SENSE relative to VEE. When SENSE exceeds 50mV, the CB comparator activates the 230A TIMER pull-up. At 100mV (60mV for the LTC4252C), the ACL amplifier servos the MOSFET current and, at 200mV, the FCL comparator abruptly pulls GATE low in an attempt to bring the MOSFET current under control. If any of these conditions persists long enough for TIMER to charge CT to 4V (see Equation 3), the LTC4252 shuts down and pulls GATE low. If the SENSE pin encounters a voltage greater than VACL, the ACL amplifier will servo GATE downwards in an attempt to control the MOSFET current. Since GATE overdrives the MOSFET in normal operation, the ACL amplifier needs time to discharge GATE to the threshold of the MOSFET. For a mild overload the ACL amplifier can control the MOSFET current, but in the event of a severe overload the current may overshoot. At SENSE = 200mV the FCL comparator takes over, quickly discharging the GATE pin to near VEE potential. FCL then releases and the ACL amplifier takes over. All the while TIMER is running. The effect of FCL is to add a nonlinear response to the control loop in favor of reducing MOSFET current. Owing to inductive effects in the system, FCL typically over corrects the current limit loop and GATE undershoots. A zero in the loop (resistor RC in series with the gate capacitor) helps the ACL amplifier to recover. SHORT-CIRCUIT OPERATION Circuit behavior arising from a load side low impedance short is shown in Figure 6 for the LTC4252. Initially, the current overshoots the fast current limit level of VSENSE = 200mV (Trace 2) as the GATE pin works to bring VGS under control (Trace 3). The overshoot glitches the backplane in the negative direction and when the current is reduced to 100mV/RS, the backplane responds by glitching in the positive direction. TIMER commences charging CT (Trace 4) while the analog current limit loop maintains the fault current at 100mV/RS, which in this case is 5A (Trace 2). Note that the backplane voltage (Trace 1) sags under load. Timer pull-up is accelerated by VOUT. When CT reaches 4V, GATE turns off, PWRGD pulls high, the load current drops to zero and the backplane rings up to over 100V. The transient associated with the GATE turn off can be controlled with a snubber to reduce ringing and a transient voltage suppressor (such as Diodes Inc. SMAT70A) to clip off large spikes. The choice of RC for the snubber is usually done experimentally. The value of the snubber capacitor is usually chosen between 10 to 100 times the MOSFET COSS. The value of the snubber resistor is typically between 3 to 100. SUPPLY RING OWING TO CURRENT OVERSHOOT SUPPLY RING OWING TO MOSFET TURN OFF -48RTN 50V/DIV ONSET OF OUTPUT SHORT-CIRCUIT SENSE 200mV/DIV GATE 10V/DIV TIMER 5V/DIV FAST CURRENT LIMIT ANALOG CURRENT LIMIT CTIMER RAMP LATCH OFF 0.5ms/DIV 4252B12 F06 Figure 6. Output Short-Circuit Behavior of LTC4252 4252b12f 18 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 APPLICATIONS INFORMATION A low impedance short on one card may influence the behavior of others sharing the same backplane. The initial glitch and backplane sag as seen in Figure 6 Trace 1, can rob charge from output capacitors on adjacent cards. When the faulty card shuts down, current flows in to refresh the capacitors. If LTC4252s are used by the other cards, they respond by limiting the inrush current to a value of 100mV/RS. If CT is sized correctly, the capacitors will recharge long before CT times out. POWER GOOD, PWRGD To begin a design, first specify the required load current and Ioad capacitance, IL and CL. The circuit breaker current trip point (VCB/RS) should be set to accommodate the maximum load current. Note that maximum input current to a DC/DC converter is expected at VSUPPLY(MIN). RS is given by: VCB(MIN) (8) RS = IL(MAX) where VCB(MIN) = 40mV (45mV for LTC4252C) represents the guaranteed minimum circuit breaker threshold. PWRGD latches low if GATE charges up to within 2.8V of VIN and DRAIN pulls below VDRNL during start-up. PWRGD is reset in UVLO, in a UV condition or if CT charges up to 4V. An overvoltage condition has no effect on PWRGD status. A 58A current pulls this pin high during reset. Due to voltage transients between the power module and PWRGD, optoisolation is recommended. This pin provides sufficient drive for an opto-coupler. Figure 19 shows an alternative NPN configuration with a limiting base resistor for the PWRGD interface. The module enable input should have protection from the negative input current. During the initial charging process, the LTC4252B may operate the MOSFET in current limit, forcing (VACL) between 80mV to 120mV (VACL is 54mV to 66mV for LTC4252C) across RS. The minimum inrush current is given by: MOSFET SELECTION The TIMER capacitor CT must be selected based on the slowest expected charging rate; otherwise TIMER might time out before the load capacitor is fully charged. A value for CT is calculated based on the maximum time it takes the load capacitor to charge. That time is given by: The external MOSFET switch must have adequate safe operating area (SOA) to handle short-circuit conditions until TIMER times out. These considerations take precedence over DC current ratings. A MOSFET with adequate SOA for a given application can always handle the required current, but the opposite may not be true. Consult the manufacturer's MOSFET data sheet for safe operating area and effective transient thermal impedance curves. MOSFET selection is a 3-step process by assuming the absence of a soft-start capacitor. First, RS is calculated and then the time required to charge the load capacitance is determined. This timing, along with the maximum short-circuit current and maximum input voltage defines an operating point that is checked against the MOSFET's SOA curve. IINRUSH(MIN) = 80mV RS (9) Maximum short-circuit current limit is calculated using the maximum VACL. This gives I SHORTCIRCUIT(MAX) = tCL(CHARGE) = C* V I = 120mV RS CL * VSUPPLY(MAX) IINRUSH(MIN) (10) (11) The maximum current flowing in the DRAIN pin is given by: IDRN(MAX) = V SUPPLY(MAX) -V DRNCL RD (12) 4252b12f 19 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 APPLICATIONS INFORMATION Approximating a linear charging rate as IDRN drops from IDRN(MAX) to zero, the IDRN component in Equation (3) can be approximated with 0.5 * IDRN(MAX). Rearranging equation, TIMER capacitor CT is given by: CT = ( tCL(CHARGE) * 230A + 4 *IDRN(MAX) 4V ) (13) Returning to Equation (3), the TIMER period is calculated and used in conjunction with VSUPPLY(MAX) and ISHORTCIRCUIT(MAX) to check the SOA curves of a prospective MOSFET. As a numerical design example, consider a 30W load, which requires 1A input current at 36V. If VSUPPLY(MAX) = 72V and CL = 100F, RD = 1M, Equation (8) gives RS = 40m; Equation (13) gives CT = 441nF. To account for errors in RS, CT, TIMER current (230A), TIMER threshold (4V), RD, DRAIN current multiplier and DRAIN voltage clamp (VDRNCL), the calculated value should be multiplied by 1.5, giving the nearest standard value of CT = 680nF. If a short-circuit occurs, a current of up to 120mV/40m = 3A will flow in the MOSFET for 5.6ms as dictated by CT = 680nF in Equation (3). The MOSFET must be selected based on this criterion. The IRF530S can handle 100V and 3A for 10ms and is safe to use in this application. Computing the maximum soft-start capacitor value during soft-start to a load short is complicated by the nonlinear MOSFET's SOA characteristics and the RSSCSS response. An overly conservative but simple approach begins with the maximum circuit breaker current, given by: VCB(MAX) I CB(MAX) = (14) RS where VCB(MAX) = 60mV (55mV for the LTC4252C). From the SOA curves of a prospective MOSFET, determine the time allowed, tSOA(MAX). CSS is given by: tSOA(MAX) CSS = (15) 0.916 *RSS In the above example, 60mV/40m gives 1.5A. tSOA(MAX) for the IRF530S is 40ms. From Equation (15), CSS = 437nF. Actual board evaluation showed that CSS = 100nF was appropriate. The ratio (RSS * CSS) to tCL(CHARGE) is a good gauge as a large ratio may result in the time-out period expiring. This gauge is determined empirically with board level evaluation. SUMMARY OF DESIGN FLOW To summarize the design flow, consider the application shown in Figure 2 with the LTC4252C. It was designed for 80W. Calculate the maximum load current: 80W/43V = 1.86A; allowing for 83% converter efficiency, IIN(MAX) = 2.2A. Calculate RS: from Equation (8) RS = 20m. Calculate ISHORTCIRCUIT(MAX): from Equation (10) ISHORTCIRCUIT(MAX) = 66mV =3.3A 20m Select a MOSFET that can handle 3.3A at 71V: IRF530S. Calculate CT: from Equation (13) CT = 322nF. Select CT = 680nF, which gives the circuit breaker time-out period t = 5.6ms. Consult MOSFET SOA curves: the IRF530S can handle 3.3A at 100V for 8.2ms, so it is safe to use in this application. Calculate CSS: using Equations (14) and (15) select CSS = 68nF. FREQUENCY COMPENSATION The LTC4252C typical frequency compensation network for the analog current limit loop is a series RC (10) and CC connected to VEE. Figure 7 depicts the relationship between the compensation capacitor CC and the MOSFET's CISS. The line in Figure 7 is used to select a starting value for CC based upon the MOSFET's CISS specification. Optimized values for CC are shown for several popular MOSFETs. Differences in the optimized value of CC versus the starting value are small. Nevertheless, compensation values should be verified by board level short-circuit testing. 4252b12f 20 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 APPLICATIONS INFORMATION COMPENSATION CAPACITANCE CC (nF) 60 CURRENT FLOW FROM LOAD NTY100N10 CURRENT FLOW TO -48V BACKPLANE 50 SENSE RESISTOR 40 TRACK WIDTH W: 0.03" PER AMP ON 1 OZ COPPER 30 4252B12 F08 IRF530S IRF740 10 0 IRF3710 IRF540S 20 W 0 2000 6000 4000 MOSFET CISS (pF) 8000 4252B12 F07 Figure 7. Recommended Compensation Capacitor CC vs MOSFET CISS As seen in Figure 6 previously, at the onset of a shortcircuit event, the input supply voltage can ring dramatically owing to series inductance. If this voltage avalanches the MOSFET, current continues to flow through the MOSFET to the output. The analog current limit loop cannot control this current flow and therefore the loop undershoots. This effect cannot be eliminated by frequency compensation. A Zener diode is required to clamp the input supply voltage and prevent MOSFET avalanche. SENSE RESISTOR CONSIDERATIONS For proper circuit breaker operation, Kelvin-sense PCB connections between the sense resistor and the LTC4252's VEE and SENSE pins are strongly recommended. The drawing in Figure 8 illustrates the correct way of making connections between the LTC4252 and the sense resistor. PCB layout should be balanced and symmetrical to minimize wiring errors. In addition, the PCB layout for the sense resistor should include good thermal management techniques for optimal sense resistor power dissipation. TIMING WAVEFORMS System Power-Up Figure 9 details the timing waveforms for a typical powerup sequence in the case where a board is already installed in the backplane and system power is applied abruptly. At TO SENSE TO VEE Figure 8. Making PCB Connections to the Sense Resistor time point 1, the supply ramps up, together with UV/OV, VOUT and DRAIN. VIN and PWRGD follow at a slower rate as set by the VIN bypass capacitor. At time point 2, VIN exceeds VLKO and the internal logic checks for UV > VUVHI, OV < VOVLO, GATE < VGATEL, SENSE < VCB, SS < 20 * VOS and TIMER < VTMRL. If all conditions are met, an initial timing cycle starts and the TIMER capacitor is charged by a 5.8A current source pull-up. At time point 3, TIMER reaches the VTMRH threshold and the initial timing cycle terminates. The TIMER capacitor is quickly discharged. At time point 4, the VTMRL threshold is reached and the conditions of GATE < VGATEL, SENSE < VCB and SS < 20 * VOS must be satisfied before a GATE ramp-up cycle begins. SS ramps up as dictated by RSS * CSS (as in Equation 6); GATE is held low by the analog current limit (ACL) amplifier until SS crosses 20 * VOS. Upon releasing GATE, 58A sources into the external MOSFET gate and compensation network. When the GATE voltage reaches the MOSFET's threshold, current begins flowing into the load capacitor at time point 5. At time point 6, load current reaches the SS control level and the analog current limit loop activates. Between time points 6 and 8, the GATE voltage is servoed, the SENSE voltage is regulated at VACL(t) (Equation 7) and soft-start limits the slew rate of the load current. If the SENSE voltage (VSENSE - VEE) reaches the VCB threshold at time point 7, the circuit breaker TIMER activates. The TIMER capacitor, CT, is charged by a (230A + 8 * IDRN) current pull-up. As the load capacitor nears full charge, load current begins to decline. 4252b12f 21 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 APPLICATIONS INFORMATION VIN CLEARS VLKO, CHECK UV > VUVHI, OV < VOVLO, GATE < VGATEL, SENSE < VCB, SS < 20 * VOS AND TIMER < VTMRL TIMER CLEARS VTMRL, CHECK GATE < VGATEL, SENSE < VCB AND SS < 20 * VOS 1 2 3 4 56 7 8 9 10 11 GND - VEE OR (-48RTN) - (-48V) UV/OV VIN VLKO VTMRH 230A + 8 * IDRN 5.8A TIMER 58A GATE 5.8A VTMRL 58A VGATEL 5.8A VIN - VGATEH 20 * (VACL + VOS) 20 * (VCB + VOS) 20 * VOS SS VACL SENSE VCB VOUT VDRNCL DRAIN VDRNL PWRGD INITIAL TIMING GATE START-UP 4252B12 F09 Figure 9. System Power-Up Timing (All Waveforms Are Referenced to VEE) At time point 8, the load current falls and the SENSE voltage drops below VACL(t). The analog current limit loop shuts off and the GATE pin ramps further. At time point 9, the SENSE voltage drops below VCB, the fault TIMER cycle ends, followed by a 5.8A discharge cycle (cool off). The duration between time points 7 and 9 must be shorter than one circuit breaker delay to avoid a fault time out during GATE ramp-up. When GATE ramps past the VGATEH threshold at time point 10, PWRGD pulls low. At time point 11, GATE reaches its maximum voltage as determined by VIN. Live Insertion with Short Pin Control of UV/OV In the example shown in Figure 10, power is delivered through long connector pins whereas the UV/OV divider 22 makes contact through a short pin. This ensures the power connections are firmly established before the LTC4252 is activated. At time point 1, the power pins make contact and VIN ramps through VLKO. At time point 2, the UV/OV divider makes contact and its voltage exceeds VUVHI. In addition, the internal logic checks for OV < VOVHI, GATE < VGATEL, SENSE < VCB, SS < 20 * VOS and TIMER < VTMRL. If all conditions are met, an initial timing cycle starts and the TIMER capacitor is charged by a 5.8A current source pull-up. At time point 3, TIMER reaches the VTMRH threshold and the initial timing cycle terminates. The TIMER capacitor is quickly discharged. At time point 4, the VTMRL threshold is reached and the conditions of GATE < VGATEL, SENSE < VCB and SS < 20 * VOS must be 4252b12f LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 APPLICATIONS INFORMATION UV CLEARS VUVHI, CHECK OV < VOVHI, GATE < VGATEL, SENSE < VCB, SS < 20 * VOS AND TIMER < VTMRL TIMER CLEARS VTMRL, CHECK GATE < VGATEL, SENSE < VCB AND SS < 20 * VOS 1 2 3 4 56 7 8 9 1011 GND - VEE OR (-48RTN) - (-48V) UV/OV VIN VUVHI VLKO VTMRH 5.8A TIMER 230A + 8 * IDRN 5.8A VTMRL GATE SS 58A 58A VGATEL 5.8A VIN - VGATEH 20 * (VACL + VOS) 20 * (VCB + VOS) 20 * VOS VACL VCB SENSE VOUT VDRNCL DRAIN VDRNL PWRGD INITIAL TIMING GATE START-UP 4252B12 F10 Figure 10. Power-Up Timing with a Short Pin (All Waveforms Are Referenced to VEE) satisfied before a GATE start-up cycle begins. SS ramps up as dictated by RSS * CSS; GATE is held low by the analog current limit amplifier until SS crosses 20 * VOS. Upon releasing GATE, 58A sources into the external MOSFET gate and compensation network. When the GATE voltage reaches the MOSFET's threshold, current begins flowing into the load capacitor at time point 5. At time point 6, load current reaches the SS control level and the analog current limit loop activates. Between time points 6 and 8, the GATE voltage is servoed, the SENSE voltage is regulated at VACL(t) and soft-start limits the slew rate of the load current. If the SENSE voltage (VSENSE - VEE) reaches the VCB threshold at time point 7, the circuit breaker TIMER activates. The TIMER capacitor, CT, is charged by a (230A + 8 * IDRN) current pull-up. As the load capacitor nears full charge, load current begins to decline. At point 8, the load current falls and the SENSE voltage drops below VACL(t). The analog current limit loop shuts off and the GATE pin ramps further. At time point 9, the SENSE voltage drops below VCB and the fault TIMER cycle ends, followed by a 5.8A discharge cycle (cool off). When GATE ramps past VGATEH threshold at time point 10, PWRGD pulls low. At time point 11, GATE reaches its maximum voltage as determined by VIN. 4252b12f 23 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 APPLICATIONS INFORMATION Undervoltage Timing cycle starts. If the system bus voltage overshoots VOVHI as shown at time point 2, TIMER discharges. At time point 3, the supply voltage recovers and drops below the VOVLO threshold. The initial timing cycle restarts, followed by a GATE start-up cycle. In Figure 11 when UV pin drops below VUVLO (time point 1), the LTC4252 shuts down with TIMER, SS and GATE all pulling low. If current has been flowing, the SENSE pin voltage decreases to zero as GATE collapses. When UV recovers and clears VUVHI (time point 2), an initial timer cycle begins followed by a GATE start-up cycle. Overvoltage Timing During normal operation, if the OV pin exceeds VOVHI as shown at time point 1 of Figure 13, the TIMER and PWRGD status are unaffected. Nevertheless, SS and GATE pull down and the load is disconnected. At time point 2, OV recovers and drops below the VOVLO threshold. A GATE start-up cycle begins. If the overvoltage glitch is long enough to deplete the load capacitor, a full start-up cycle as shown between time points 4 through 7 may occur. VIN Undervoltage Lockout Timing The VIN undervoltage lockout comparator, UVLO, has a similar timing behavior as the UV pin timing except it looks for VIN < (VLKO - VLKH) to shut down and VIN > VLKO to start. In an undervoltage lockout condition, both UV and OV comparators are held off. When VIN exits undervoltage lockout, the UV and OV comparators are enabled. Circuit Breaker Timing Undervoltage Timing with Overvoltage Glitch In Figure 14a, the TIMER capacitor charges at 230A if the SENSE pin exceeds VCB but VDRN is less than 5V. If the SENSE pin drops below VCB before TIMER reaches In Figure 12, both UV and OV pins are connected together. When UV clears VUVHI (time point 1), an initial timing UV DROPS BELOW VUVLO. GATE, SS AND TIMER ARE PULLED DOWN, PWRGD RELEASES UV CLEARS VUVHI, CHECK OV CONDITION, GATE < VGATEL, SENSE < VCB, SS < 20 * VOS AND TIMER < VTMRL TIMER CLEARS VTMRL, CHECK GATE < VGATEL, SENSE < VCB AND SS < 20 * VOS 1 UV 2 3 4 56 7 8 9 10 11 VUVHI VUVLO VTMRH 5.8A TIMER 230A + 8 * IDRN 58A GATE SS 5.8A VTMRL 58A VGATEL 5.8A VIN - VGATEH 20 * (VACL + VOS) 20 * (VCB + VOS) 20 * VOS VACL SENSE VCB VDRNCL DRAIN VDRNL PWRGD INITIAL TIMING GATE START-UP 4252B12 F11 Figure 11. Undervoltage Timing (All Waveforms Are Referenced to VEE) 4252b12f 24 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 APPLICATIONS INFORMATION UV/OV CLEARS VUVHI, CHECK OV CONDITION, GATE < VGATEL, SENSE < VCB, SS < 20 * VOS AND TIMER < VTMRL UV/OV OVERSHOOTS VOVHI AND TIMER ABORTS INITIAL TIMING CYCLE UV/OV DROPS BELOW VOVLO AND TIMER RESTARTS INITIAL TIMING CYCLE TIMER CLEARS VTMRL, CHECK GATE < VGATEL, SENSE < VCB AND SS < 20 * VOS 1 2 3 VOVHI UV/OV 4 5 67 8 10 12 9 11 VOVLO VUVHI VTMRH 230A + 8 * IDRN 5.8A TIMER 5.8A VTMRL 58A GATE 58A VGATEL 5.8A VIN - VGATEH 20 * (VACL + VOS) 20 * (VCB + VOS) 20 * VOS SS VACL VCB SENSE VDRNCL DRAIN VDRNL PWRGD GATE START-UP INITIAL TIMING 4252B12 F12 Figure 12. Undervoltage Timing with an Overvoltage Glitch (All Waveforms Are Referenced to VEE) OV OVERSHOOTS VOVHI. GATE AND SS ARE PULLED DOWN, PWRGD AND TIMER ARE UNAFFECTED OV DROPS BELOW VOVLO, CHECK GATE < VGATEL, SENSE < VCB AND SS < 20 * VOS 1 OV 2 34 VOVHI 5 67 8 9 VOVLO VTMRH 5.8A 230A + 8 * IDRN TIMER 58A GATE VGATEL 58A 5.8A VIN - VGATEH 20 * (VACL + VOS) SS 20 * VOS 20 * (VCB + VOS) VACL VCB SENSE GATE START-UP 4252B12 F13 Figure 13. Overvoltage Timing (All Waveforms Are Referenced to VEE) 4252b12f 25 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 APPLICATIONS INFORMATION CB TIMES OUT 1 2 1 VTMRH 2 1 VTMRH 5.8A TIMER 230A + 8 * IDRN CB TIMES OUT VTMRH TIMER 230A + 8 * IDRN TIMER GATE GATE GATE SS SS SS SENSE VACL VACL VCB VCB SENSE VOUT VOUT 2 3 230A + 8 * IDRN 230A + 8 * IDRN VACL VCB SENSE VOUT VDRNCL VDRNCL DRAIN DRAIN DRAIN PWRGD PWRGD PWRGD CB FAULT CB FAULT 4 5.8A CB FAULT CB FAULT 4252B12 F14 (14a) Momentary Circuit-Breaker Fault (14b) Circuit-Breaker Time Out (14c) Multiple Circuit-Breaker Fault Figure 14. Circuit-Breaker Timing Behavior (All Waveforms Are Referenced to VEE) the VTMRH threshold, TIMER is discharged by 5.8A. In Figure 14b, when TIMER exceeds VTMRH, GATE pulls down immediately and the LTC4252 shuts down. In Figure 14c, multiple momentary faults cause the TIMER capacitor to integrate and reach VTMRH. GATE pull down follows and the LTC4252 shuts down. During shutdown, the LTC42521 latches TIMER high with a 5.8A pull-up current source; the LTC4252-2 activates a shutdown cooling cycle. Resetting a Fault Latch (LTC4252-1) The latched circuit breaker fault of LTC4252-1 benefits from long cooling time. It is reset by pulling the UV pin below VUVLO with a switch. Reset is also accomplished by pulling the VIN pin momentarily below (VLKO - VLKH). A third reset method involves pulling the TIMER pin below VTMRL as shown in Figure 15. An initial timing cycle is skipped if TIMER is used for reset. An initial timing cycle is generated if reset by the UV pin or the VIN pin. The duration of the TIMER reset pulse should be smaller than the time taken to reach 0.2V at SS pin. With a single 26 pole mechanical pushbutton switch, this may not be feasible. A double pole, single throw pushbutton switch removes this restriction by connecting the second switch to the SS pin. With this method, both the SS and TIMER pins are released at the same time (see Figure 24). Shutdown Cooling Cycle (LTC4252-2) Figure 16 shows the timer behavior of the LTC4252-2. At time point 2, TIMER exceeds VTMRH, GATE pulls down immediately and the LTC4252 shuts down. TIMER starts a shutdown cooling cycle by discharging TIMER with 5.8A to the VTMRL threshold. TIMER then charges with 5.8A to the VTMRH threshold. There are four 5.8A discharge phases and three 5.8A charge phases in this shutdown cooling cycle spanning time points 2 and 3. At time point 3, the LTC4252 automatic retry occurs with a start-up cycle. Good thermal management techniques are highly recommended; power and thermal dissipation must be carefully evaluated when implementing the automatic retry scheme. 4252b12f LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 APPLICATIONS INFORMATION SWITCH RESETS LATCHED TIMER SWITCH RELEASES SS 5.8A 1 2 34 TIMER 67 8 9 5.8A 58A GATE VGATEL SS 5 VTMRH 230A + 8 * IDRN VTMRL 58A 5.8A VIN - VGATEH 20 * (VACL + VOS) 20 * (VCB + VOS) 20 * VOS VACL VCB SENSE VDRNCL DRAIN VDRNL PWRGD 425212B F15 GATE START-UP MOMENTARY DPST SWITCH RESET Figure 15. Pushbutton Reset of LTC4252-1's Latched Fault (All Waveforms Are Referenced to VEE) RETRY CIRCUIT BREAKER TIMES OUT 1 230A + 8 * IDRN TIMER 2 5.8A 5.8A VTMRL 3 45 5.8A 5.8A 5.8A 5.8A 6 78 9 10 VTMRH 230A + 8 * IDRN 5.8A 58A GATE VGATEL 58A 5.8A 5.8A VIN - VGATEH 20 * (VACL + VOS) 20 * (VCB + VOS) 20 * VOS SS VACL VCB SENSE VOUT VDRNCL DRAIN VDRNL PWRGD CB FAULT SHUTDOWN COOLING GATE START-UP 4252B12 F16 Figure 16. Shutdown Cooling Timing Behavior of LTC4252-2 (All Waveforms Are Referenced to VEE) 4252b12f 27 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 APPLICATIONS INFORMATION Analog Current Limit and Fast Current Limit In Figure 17a, when SENSE exceeds VACL, GATE is regulated by the analog current limit amplifier loop. When SENSE drops below VACL, GATE is allowed to pull up. In Figure 17b, when a severe fault occurs, SENSE exceeds VFCL and GATE immediately pulls down until the analog current amplifier establishes control. If the severe fault causes VOUT to exceed VDRNCL, the DRAIN pin is clamped at VDRNCL. IDRN flows into the DRAIN pin and is multiplied by 8. This extra current is added to the TIMER pull-up current of 230A. This accelerated TIMER current of [230A+8 * IDRN] produces a shorter circuit breaker fault delay. Careful selection of CT, RD and MOSFET can help prevent SOA damage in a low impedance fault condition. Soft-Start If the SS pin is not connected, this pin defaults to a linear voltage ramp, from 0V to 2.2V in about 180s (or 0V to 1.4V in 230s for the LTC4252C) at GATE start-up, as shown in Figure 18a. If a soft-start capacitor, CSS, is connected to this SS pin, the soft-start response is modified from a linear ramp to an RC response (Equation 6), as shown in Figure 18b. This feature allows load current to slowly ramp-up at GATE start-up. Soft-start is initiated at time point 3 by a TIMER transition from VTMRH to VTMRL (time points 1 to 2) or by the OV pin falling below the VOVLO threshold after an OV condition. When the SS pin is below 0.2V, the analog current limit amplifier holds GATE low. Above 0.2V, GATE is released and 58A ramps up the compensation network and GATE capacitance at time point 4. Meanwhile, the SS pin voltage continues to ramp up. When GATE reaches the MOSFET's threshold, the MOSFET begins to conduct. Due to the MOSFET's high gm, the MOSFET current quickly reaches the soft-start control value of VACL(t) (Equation 7). At time point 6, the GATE voltage is controlled by the current limit amplifier. The soft-start control voltage reaches the circuit breaker voltage, VCB, at time point 7 and the circuit breaker TIMER activates. As the load capacitor nears full charge, load CB TIMES OUT 12 230A + 8 * IDRN 34 VTMRH 5.8A TIMER 5.8A VTMRH 230A + 8 * IDRN TIMER GATE GATE SS SS VACL SENSE VCB SENSE VOUT VOUT DRAIN DRAIN PWRGD PWRGD 1 2 VFCL VACL VCB VDRNCL 4252B12 F17 (17a) Analog Current Limit Fault (17b) Fast Current Limit Fault Figure 17. Current Limit Behavior (All Waveforms Are Referenced to VEE) 4252b12f 28 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 APPLICATIONS INFORMATION END OF INTIAL TIMING CYCLE 12 34 567 7a END OF INTIAL TIMING CYCLE 8 9 10 VTMRH 230A + 8 * IDRN TIMER 5.8A VTMRL 58A GATE 11 VIN - VGATEH VGS(th) 12 3 4 5 6 TIMER 20 * (VCB + VOS) VGS(th) VCB 5.8A DRAIN PWRGD VIN - VGATEH 20 * (VCB + VOS) 20 * VOS VACL SENSE VCB VDRNCL VDRNL 11 58A 20 * (VACL + VOS) SS VACL 10 VTMRL 20 * VOS SENSE 8 9 58A GATE 58A 20 * (VACL + VOS) SS 7 VTMRH 230A + 8 * IDRN VDRNCL VDRNL DRAIN PWRGD 4252B12 F18 (18a) Without External CSS (18b) With External CSS Figure 18. Soft-Start Timing (All Waveforms Are Referenced to VEE) current begins to decline below VACL(t). The current limit loop shuts off and GATE releases at time point 8. At time point 9, the SENSE voltage falls below VCB and TIMER deactivates. Large values of CSS can cause premature circuit breaker time out as VACL(t) may exceed the VCB potential during the circuit breaker delay. The load capacitor is unable to achieve full charge in one GATE start-up cycle. A more serious side effect of large CSS values is SOA duration may be exceeded during soft-start into a low impedance load. A soft-start voltage below VCB will not activate the circuit breaker TIMER. Power Limit Circuit Breaker Figure 19 shows the LTC4252C-1 in a power limit circuit breaking application. The SENSE pin is modulated by the board supply voltage, VSUPPLY. The D1 Zener voltage, VZ is set to be the same as the low supply operating voltage, VSUPPLY(MIN) = 43V. If the goal is to have the high supply operating voltage, VSUPPLY(MAX) = 71V giving the same power at VSUPPLY(MIN), then resistors R4 and R6 are selected using the ratio: VCB R6 = R4 VSUPPLY(MAX) (16) If R6 is 27, R4 is 38.3k. The peak circuit breaker power limit is: POWERMAX (V = SUPPLY(MIN) +VSUPPLY(MAX) ) 2 4 * VSUPPLY(MIN) * VSUPPLY(MAX) *POWERSUPPLY(MIN) (17) =1.064 *POWERSUPPLY(MIN) when VSUPPLY = 0.5 * (VSUPPLY(MIN) + VSUPPLY(MAX)) = 57V. The peak power at the fault current limit occurs at the supply overvoltage threshold. The fault current limited power is: POWERFAULT = VSUPPLY R6 * VACL - ( VSUPPLY -VZ ) * RS R4 (18) 4252b12f 29 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 APPLICATIONS INFORMATION -48RTN RIN 3x 1.8k 1/4W EACH -48RTN (SHORT PIN) 1 R1 392k 1% 8 10 R2 30.1k 1% -48V DIN DDZ13B** CIN 1F VIN 9 3 CT 0.68F C1 10nF LTC4252C-1 2 UV PWRGD 7 OV DRAIN 6 TIMER GATE 4 SS VEE SENSE CSS 68nF + R4 38.3k CL 100F R5 100k LOAD EN D1 BZV85C43 * VOUT RD 1M Q1 IRF530S R6 27 RC 10 CC 10nF 5 RS 0.02 4252B12 F19 *FMMT493 **DIODES, INC RECOMMENDED FOR HARSH ENVIRONMENTS Figure 19. Power Limit Circuit Breaking Application Circuit Breaker with Foldback Current Limit Figure 20 shows the LTC4252C in a foldback current limit application. When VOUT is shorted to the -48V RTN supply, current flows through resistors R4 and R5. This results in a voltage drop across R5 and a corresponding reduction in voltage drop across the sense resistor, RS, as the ACL amplifier servos the sense voltage between the SENSE and VEE pins to about 60mV. The short-circuit current through RS reduces as the VOUT voltage increases during an output short-circuit condition. Without foldback current limiting resistor R5, the current is limited to 3A during analog current limit. With R5, the short-circuit current is limited to 0.5A when VOUT is shorted to 71V. Inrush Control Without a Sense Resistor During Power-Up Figure 21 shows the LTC4252C in an application where the inrush current is controlled without a sense resistor during power-up. This setup is suitable only for applications that don't require short-circuit protection from the LTC4252C. Resistor R4 and capacitor C2 act as a feedback network to accurately control the inrush current. The C2 capacitor can be calculated with the following equation: *C I C2= GATE L (19) IINRUSH where IGATE = 58A and CL is the total load capacitance. 30 Capacitor C3 and resistor R4 prevent Q1 from momentarily turning on when the power pins first make contact. Without C3 and R4, capacitor C2 pulls the gate of Q1 up to a voltage roughly equal to VEE * C2/CGS(Q1) before the LTC4252C powers up. By placing capacitor C3 in parallel with the gate capacitance of Q1 and isolating them from C2 using resistor R4, the problem is solved. The value of C3 is given by: C3= VSUPPLY(MAX) VGS(TH),Q1 ( * C2+CGD(Q1) ) (20) C3 35 * C2 for VSUPPLY(MAX) = 71V where VGS(TH),Q1 is the MOSFET's minimum gate threshold and VSUPPLY(MAX) is the maximum operating input voltage. Diode-ORing Figure 22 shows the LTC4252B used as diode-oring with Hot Swap capability in a dual - 48V power supply application. The conventional diode-OR method uses two high power diodes and heat sinks to contain the large heat dissipation of the diodes. With the LTC4252B controlling the external FETs Q2 and Q3 in a diode-OR manner, the small turn-on voltage across the fully enhanced Q2 and Q3 reduces the power dissipation significantly. 4252b12f LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 APPLICATIONS INFORMATION -48RTN + RIN 3x 1.8k 1/4W EACH -48RTN (SHORT PIN) 1 R1 392k 1% 8 9 C1 10nF R2 30.1k 1% -48V OV UV 10 TIMER 3 CT SS 0.68F **DIODES, INC CIN 1F VIN LTC4252C-1 2 PWRGD 7 DRAIN GATE VEE SENSE R3 5.1k LOAD EN * VOUT RD 1M 6 R4 38.3k R 10 G 4 R5 27 Q1 IRF530S RC 10 CC 10nF 5 CSS 68nF *MOC207 DIN DDZ13B** CL 100F RS 0.02 4252B12 F20 RECOMMENDED FOR HARSH ENVIRONMENTS Figure 20. Circuit Breaker with Foldback Current Limit Application -48RTN + RIN 3x 1.8k 1/4W EACH -48RTN (SHORT PIN) 1 R1 392k 1% 9 10 -48V *MOC207 CIN 1F R3 5.1k VIN 8 C1 10nF R2 30.1k 1% DIN DDZ13B** CT 0.68F 3 OV UV TIMER SS CSS 68nF **DIODES, INC LTC4252C-1 2 PWRGD 7 DRAIN GATE VEE SENSE CL 100F LOAD EN * VOUT RD 1M C2 10nF 100V R4 1k 1% RG 10 6 4 C3 330nF 25V 5 Q1 IRF530S 4252B12 F21 RECOMMENDED FOR HARSH ENVIRONMENTS Figure 21. Inrush Control Without a Sense Resistor Application At power-up, Q5 and Q8 are held off low by the SS pin of the LTC4252B; resistors R5 and R8 pull the SENSE pin closed to VEE. VEE is connected to the power supply with lower voltage through the body diodes Q2 or Q3 until Q2 or Q3 is turned on. This allows the LTC4252B to perform a start-up cycle and ramp up the SS and GATE voltage. As the SS voltage ramps up to 2.2V, it turns on Q5 and Q8 and pulls TIMER low through Q6 and Q9. The sense voltage rises as current flows into R5 and R8 through resistors R3 and R6. The ACL amplifier of the LTC4252B servos the sense voltage to about 100mV as the GATE voltage regulates Q2 and Q3. Current flows into R4, Q4 and R7, Q7 as Q2 and Q3 turn on. The respective node voltages at the R3 and R4 connection and the R6 and R7 connection are always kept equal to their respective sense voltages by the Q4 and Q2 VDS drop and the Q7 and Q3 VDS drop assuming the Q5 and Q8 VDS drop is negligible. 4252b12f 31 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 APPLICATIONS INFORMATION Hot Swap SECTION -48RTN RIN1 3 x 1.8k IN SERIES 1/4W EACH R1 402k 1 7 C1 10nF 8 CT 0.33F R2 32.4k 2 UV/OV VIN DIN1 DDZ13B** DRAIN GATE TIMER LTC4252B-1 SS VEE SENSE CSS 68nF 6 CIN 1F RD 1M LOAD MODULE 5 3 RC1 10 CC1 22nF Q1 IRF530S RS 0.02 4 DIODE-OR CIRCUIT FOR CHANNEL A -48V A RIN2 3 x 1.8k IN SERIES 1/4W EACH 1 DIN2 DDZ13B** CIN2 1F 9 VIN 7 DRAIN UV PWRGD LTC4252B-2 4 10 SENSE TIMER 3 SS 6 8 GATE OV VEE 2 Q6 FDV301N 5 R3 12k Q5 FDV301N R4 150 Q4 BSS131 R5 560 RC2 10 CC2 22nF Q2 IRF530S DIODE-OR CIRCUIT FOR CHANNEL B -48V B RIN3 3 x 1.8k IN SERIES 1/4W EACH 1 DIN3 DDZ13B** CIN3 1F 9 VIN 7 DRAIN UV PWRGD LTC4252B-2 4 10 TIMER SENSE 3 SS 6 8 GATE OV VEE 2 Q9 FDV301N 5 **DIODES, INC R6 12k Q8 FDV301N R7 150 Q7 BSS131 R8 560 RC3 10 CC3 22nF RECOMMENDED FOR HARSH ENVIRONMENTS Q3 IRF530S 4252B12 F22 Figure 22. -48V/2.5A Diode-OR Application 4252b12f 32 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 APPLICATIONS INFORMATION the current flow. The sense voltage is lifted up and causes the fast comparator of LTC4252B to trip and pull the GATE low instantly. The channel A supply short will not cause Q3 of channel B diode-OR circuit to turn off. The internal fault latches of the LTC4252B are disabled as the TIMER pin is always held low by the SS voltage when Q2 and Q3 are in analog current limit. If both power supplies from channel A and B are exactly equal, then equal load current will flow through Q2 and Q3 to the load module via the Hot Swap section. If the channel A supply is greater than the channel B by more than 100mV, the sense voltage will rise above the fast comparator trip threshold of 200mV, the GATE will be pulled low and Q2 is turned off. The GATE ramps up and regulates Q2 when the channel A supply is equal to the channel B supply. Likewise, if the channel B supply is greater than channel A by more than 100mV, it trips the fast comparator and GATE is pulled low and Q3 is turned off. The GATE ramps up and regulates Q3 when the channel B supply is equal to the channel A supply. Resistors R4, R7 and external FETs Q4 and Q7 limit the current flow into Q5 and Q8 during their respective supply source short. When the channel A supply is shorted to the - 48V RTN (or GND), large current flows into Q4 momentarily and creates a voltage drop across R4, which in turn reduces the gate-to-source voltage of Q4, limiting Similarly, when the channel B supply is shorted to the -48V RTN (or GND), large current flows into Q7 momentarily and creates a voltage drop across R7, which in turn reduces the gate-to-source voltage of Q7, thus limiting the current flow. The increase in sense voltage will trip the fast comparator of LTC4252B and pull the GATE low instantly. The channel B supply short will not cause Q2 of channel A diode-OR circuit to turn off. The load short at the output of Q1 is protected by the Hot Swap section. Using an EMI Filter Module Many applications place an EMI filter module in the power path to prevent switching noise of the module from being injected back onto the power supply. A typical application using the Lucent FLTR100V10 filter module is shown in Figure 23. When using a filter, an opto-isolator is required to prevent common mode transients from destroying the PWRGD and ON/OFF pins. -48RTN (LONG PIN) RIN 3x 1.8k 1/4W -48RTN (SHORT PIN) 1 R1 392k 1% C1 10nF R2 30.1k 1% -48V DIN DDZ13B** VIN LTC4252C-1 2 8 OV PWRGD 7 9 DRAIN UV 10 3 CT 0.68F TIMER SS GATE VEE CSS 68nF SENSE 5 6 CIN 1F 1 R3 5.1k 4 RC 10 CC 10nF VOUT+ 9 5V + 8 SENSE 2 * RD 1M VIN+ Q1 IRF530S 1N4003 VIN+ VOUT+ C2 LUCENT 0.1F 100V FLTR100V10 VIN- RS 0.02 VOUT- TRIM 7 ON/OFF + LUCENT JW050A1-E C3 + 0.1F 100V C4 100F 100V C5 0.1F 100V 4 CASE VIN- SENSE- 6 VOUT- 5 C6 100F 16V CASE 3 4252B12 F23 *MOC207 **DIODES, INC RECOMMENDED FOR HARSH ENVIRONMENTS Figure 23. Typical Application Using a Filter Module 4252b12f 33 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 PACKAGE DESCRIPTION Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. MS8 Package 8-Lead Plastic MSOP (Reference LTC DWG # 05-08-1660 Rev F) 0.889 0.127 (.035 .005) 5.23 (.206) MIN 3.20 - 3.45 (.126 - .136) 3.00 0.102 (.118 .004) (NOTE 3) 0.65 (.0256) BSC 0.42 0.038 (.0165 .0015) TYP 8 7 6 5 0.52 (.0205) REF RECOMMENDED SOLDER PAD LAYOUT 0.254 (.010) 3.00 0.102 (.118 .004) (NOTE 4) 4.90 0.152 (.193 .006) DETAIL "A" 0 - 6 TYP GAUGE PLANE 0.53 0.152 (.021 .006) DETAIL "A" 1 2 3 4 1.10 (.043) MAX 0.86 (.034) REF 0.18 (.007) SEATING PLANE 0.22 - 0.38 (.009 - .015) TYP 0.65 (.0256) BSC 0.1016 0.0508 (.004 .002) MSOP (MS8) 0307 REV F NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX 4252b12f 34 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 PACKAGE DESCRIPTION Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. MS Package 10-Lead Plastic MSOP (Reference LTC DWG # 05-08-1661 Rev E) 0.889 0.127 (.035 .005) 5.23 (.206) MIN 3.20 - 3.45 (.126 - .136) 3.00 0.102 (.118 .004) (NOTE 3) 0.50 0.305 0.038 (.0197) (.0120 .0015) BSC TYP RECOMMENDED SOLDER PAD LAYOUT 0.254 (.010) 10 9 8 7 6 3.00 0.102 (.118 .004) (NOTE 4) 4.90 0.152 (.193 .006) DETAIL "A" 0.497 0.076 (.0196 .003) REF 0 - 6 TYP GAUGE PLANE 1 2 3 4 5 0.53 0.152 (.021 .006) DETAIL "A" 0.18 (.007) SEATING PLANE 1.10 (.043) MAX 0.17 - 0.27 (.007 - .011) TYP 0.50 (.0197) NOTE: BSC 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX 0.86 (.034) REF 0.1016 0.0508 (.004 .002) MSOP (MS) 0307 REV E 4252b12f Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 35 LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 TYPICAL APPLICATION -48RTN RIN 2x 5.1k IN SERIES 1/4W EACH DIN DDZ13B** -48RTN (SHORT PIN) CL 100F VOUT LTC4252B-1 7 R2 32.4k 1% 8 2 CT 150nF C1 10nF UV/OV DRAIN TIMER GATE SS CSS 27nF PUSH RESET VEE LOAD CIN 1F 1 VIN R1 402k 1% + SENSE 4 6 RD 1M 5 Q1 IRF540S 3 R3 22 RC 10 CC 22nF RS 0.01 4252B12 F24 -48V **DIODES, INC RECOMMENDED FOR HARSH ENVIRONMENTS Figure 24. - 48V/5A Application RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT1640AH/LT1640AL Negative High Voltage Hot Swap Controllers in SO-8 Negative High Voltage Supplies from -10V to - 80V LT1641-1/LT1641-2 Positive High Voltage Hot Swap Controllers in SO-8 Supplies from 9V to 80V, Latched Off/Autoretry LTC1642 Fault Protected Hot Swap Controller 3V to 16.5V, Overvoltage Protection up to 33V LTC4214 Negative Voltage Hot Swap Controller Operates from -6V to -16V LTC4220 Dual Supply Hot Swap Controller 2.2V to 16.5V Operation LT4250 - 48V Hot Swap Controller in SO-8 Active Current Limiting, Supplies from -20V to -80V LTC4251B/ LTC4251B-1/ LTC4251B-2 -48V Hot Swap Controllers in SOT-23 Fast Active Current Limiting, Supplies from -15V LTC4253B -48V Hot Swap Controller with Sequencer Fast Current Limiting with Three Sequenced Power Good Outputs, Supplies from -15V 4252b12f 36 Linear Technology Corporation LT 0112 * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com LINEAR TECHNOLOGY CORPORATION 2012