TSOP22.., TSOP24.. Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES * Low supply current * Photo detector and preamplifier in one package * Internal filter for PCM frequency * Improved shielding against EMI * Supply voltage: 2.7 V to 5.5 V 1 2 * Improved immunity against ambient light 3 16672 * Insensitive to supply voltage ripple and noise * Compliant to RoHS directive 2002/95/EC and in accordance to WEEE 2002/96/EC MECHANICAL DATA Pinning DESCRIPTION 1 = OUT, 2 = VS, 3 = GND The TSOP22.., TSOP24.. series are miniaturized receivers for infrared remote control systems. A PIN diode and a preamplifier are assembled on a lead frame, the epoxy package acts as an IR filter. The demodulated output signal can be directly decoded by a microprocessor. The TSOP22.. is compatible with all common IR remote control data formats. The TSOP24.. is optimized to suppress almost all spurious pulses from energy saving fluorescent lamps but will also suppress some data signals. This component has not been qualified according to automotive specifications. PARTS TABLE CARRIER FREQUENCY STANDARD APPLICATIONS (AGC2/AGC8) VERY NOISY ENVIROMENTS (AGC4) 30 kHz TSOP2230 TSOP2430 33 kHz TSOP2233 TSOP2433 36 kHz TSOP2236 TSOP2436 36.7 kHz TSOP2237 TSOP2437 38 kHz TSOP2238 TSOP2438 40 kHz TSOP2240 TSOP2440 56 kHz TSOP2256 TSOP2456 BLOCK DIAGRAM APPLICATION CIRCUIT 17170_7 2 33 k VS 1 Input AGC Band pass Demodulator OUT 3 PIN Document Number: 82095 Rev. 2.2, 20-Aug-10 Control circuit GND Transmitter with TSALxxxx R1 IR receiver VS Circuit 16833_7 + VS C1 C OUT GND VO GND The external components R1 and C1 are optional to improve the robustness against electrical overstress (typical values are R1 = 100 , C1 = 0.1 F). The output voltage VO should not be pulled down to a level below 1 V by the external circuit. The capacitive load at the output should be less than 2 nF. www.vishay.com 1 TSOP22.., TSOP24.. Vishay Semiconductors IR Receiver Modules for Remote Control Systems ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL VALUE Supply voltage (pin 2) TEST CONDITION VS - 0.3 to + 6 V Supply current (pin 2) IS 5 mA Output voltage (pin 1) Voltage at output to supply UNIT VO - 0.3 to 5.5 V VS - VO - 0.3 to (VS + 0.3) V mA Output current (pin 1) IO 5 Junction temperature Tj 100 C Tstg - 25 to + 85 C Storage temperature range Operating temperature range Tamb - 25 to + 85 C Tamb 85 C Ptot 10 mW t 10 s, 1 mm from case Tsd 260 C Power consumption Soldering temperature Note * Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability. ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) PARAMETER Supply current (pin 2) TEST CONDITION SYMBOL MIN. TYP. MAX. Ev = 0, VS = 5 V ISD 0.65 0.85 1.05 Ev = 40 klx, sunlight ISH Supply voltage VS mA 2.7 d IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see fig. 1 VOSL Minimum irradiance Pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1 Ee min. Maximum irradiance tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1 Ee max. Directivity Angle of half transmission distance 1/2 Output voltage low (pin 1) mA 0.95 Ev = 0, test signal see fig. 1, IR diode TSAL6200, IF = 400 mA Transmission distance UNIT 5.5 V 45 m 0.17 100 mV 0.35 mW/m2 W/m2 30 45 deg TYPICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) Optical Test Signal 1.0 (IR diode TSAL6200, IF = 0.4 A, 30 pulses, f = f0, t = 10 ms) t tpi * * tpi VO T 10/f0 is recommended for optimal function Output Signal 1) 2) VOH 16110 7/f0 < td < 15/f0 tpi - 5/f0 < tpo < tpi + 6/f 0 tpo - Output Pulse Width (ms) Ee Output Pulse Width 0.9 0.8 Input Burst Length 0.7 0.6 0.5 0.4 = 950 nm, Optical Test Signal, Fig.1 0.3 0.2 VOL td 1) tpo 2) t 0.1 21391 Fig. 1 - Output Active Low www.vishay.com 2 1 10 102 103 104 105 Ee - Irradiance (mW/m2) Fig. 2 - Pulse Length and Sensitivity in Dark Ambient Document Number: 82095 Rev. 2.2, 20-Aug-10 TSOP22.., TSOP24.. IR Receiver Modules for Remote Control Systems 600 s t 600 s t = 60 ms 94 8134 Output Signal, (see fig. 4) VO VOH VOL t t off t on 5 Ee min. - Threshold Irradiance (mW/m2) Optical Test Signal Ee 4 3.5 3 2.5 2 1.5 0 0.01 0.6 Toff 0.4 0.3 0.2 = 950 nm, Optical Test Signal, Fig. 3 0 0.1 1 10 102 103 104 100 f = f0 0.5 0.4 f = 30 kHz f = 20 kHz 0.3 0.2 0.1 f = 10 kHz f = 100 Hz 0 1 10 100 1000 VsRMS - AC Voltage on DC Supply Voltage (mV) Fig. 7 - Sensitivity vs. Supply Voltage Disturbances 1.2 E - Max. Field Strength (V/m) 500 1.0 E e min./Ee - Rel. Responsivity 10 0.6 21394_1 Fig. 4 - Output Pulse Diagram 0.8 0.6 0.4 f = f0 5 % f(3 dB) = f0/10 0.2 450 400 350 300 250 200 150 100 50 0.0 0 0.7 16925 1 0.7 105 Ee - Irradiance (mW/m2) 21392 0.1 Ee - Ambient DC Irradiance (W/m2) 21393_1 Ee min. - Threshold Irradiance (mW/m2) Ton, Toff - Output Pulse Width (ms) Ton 0.1 Wavelength of Ambient Illumination: = 950 nm 1 0.5 Fig. 6 - Sensitivity in Bright Ambient 0.8 0.5 Correlation with Ambient Light Sources: 10 W/m2 = 1.4 kLx (Std. illum. A, T = 2855 K) 10 W/m2 = 8.2.kLx (Daylight, T = 5900 K) 4.5 Fig. 3 - Output Function 0.7 Vishay Semiconductors 0.9 1.1 f/f0 - Relative Frequency Fig. 5 - Frequency Dependence of Responsivity Document Number: 82095 Rev. 2.2, 20-Aug-10 0 1.3 20747 500 1000 1500 2000 2500 3000 f - EMI Frequency (MHz) Fig. 8 - Sensitivity vs. Electric Field Disturbances www.vishay.com 3 TSOP22.., TSOP24.. IR Receiver Modules for Remote Control Systems Vishay Semiconductors 0 0.8 10 20 30 Max. Envelope Duty Cycle 0.7 0.6 TSOP22.. 40 0.5 1.0 0.4 0.3 0.2 50 0.8 60 TSOP24.. 70 0.7 0.1 0 0.9 80 f = 38 kHz, Ee = 2 mW/m 0 21396_4 20 40 60 80 100 120 0.6 Burst Length (number of cycles/burst) 96 12223p2 Ee min. - Sensitivity (mW/m2) Ee min. - Threshold Irradiance (mW/m2) 0 0.4 0.3 0.25 0.2 0.15 0.1 0.05 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0 - 10 10 30 50 70 90 1.5 21398_1 Tamb - Ambient Temperature (C) 21397_1 0.2 Fig. 12 - Horizontal Directivity Fig. 9 - Max. Envelope Duty Cycle vs. Burst Length 0 - 30 0.4 drel - Relative Transmission Distance Fig. 10 - Sensitivity vs. Ambient Temperature 2.5 3.5 4.5 5.5 VS - Supply Voltage (V) Fig. 13 - Sensitivity vs. Supply Voltage S ( ) rel - Relative Spectral Sensitivity 1.2 1.0 0.8 0.6 0.4 0.2 0.0 750 16919 850 950 1050 1150 - Wavelength (nm) Fig. 11 - Relative Spectral Sensitivity vs. Wavelength www.vishay.com 4 Document Number: 82095 Rev. 2.2, 20-Aug-10 TSOP22.., TSOP24.. IR Receiver Modules for Remote Control Systems Vishay Semiconductors SUITABLE DATA FORMAT IR Signal The TSOP22.., TSOP24.. series are designed to suppress spurious output pulses due to noise or disturbance signals. Data and disturbance signals can be distinguished by the devices according to carrier frequency, burst length and envelope duty cycle. The data signal should be close to the band-pass center frequency (e.g. 38 kHz) and fulfill the conditions in the table below. When a data signal is applied to the TSOP22.., TSOP24.. in the presence of a disturbance signal, the sensitivity of the receiver is reduced to insure that no spurious pulses are present at the output. Some examples of disturbance signals which are suppressed are: IR Signal from Fluorescent Lamp with Low Modulation 0 * DC light (e.g. from tungsten bulb or sunlight) 5 * Continuous signals at any frequency 10 15 20 Time (ms) 16920 Fig. 14 - IR Signal from Fluorescent Lamp with Low Modulation * Strongly or weakly modulated noise from fluorescent lamps with electronic ballasts (see figure 14 or figure 15) IR Signal IR Signal from Fluorescent Lamp with High Modulation 0 16921 5 10 15 20 Time (ms) Fig. 15 - IR Signal from Fluorescent Lamp with High Modulation TSOP22.. TSOP24.. Minimum burst length 10 cycles/burst 10 cycles/burst After each burst of length a minimum gap time is required of 10 to 70 cycles 12 cycles 10 to 35 cycles 12 cycles For bursts greater than a minimum gap time in the data stream is needed of 70 cycles > 4 x burst length 35 cycles > 10 x burst length Maximum number of continuous short bursts/second 800 1300 Recommended for NEC code yes yes Recommended for RC5/RC6 code yes yes Recommended for Sony code yes no Recommended for Thomson 56 kHz code yes yes Recommended for Mitsubishi code (38 kHz, preburst 8 ms, 16 bit) yes yes Recommended for Sharp code Suppression of interference from fluorescent lamps yes yes Most common disturbance signals are suppressed Even extreme disturbance signals are suppressed Note * For data formats with short bursts please see the datasheet of TSOP21.., TSOP23.. . Document Number: 82095 Rev. 2.2, 20-Aug-10 www.vishay.com 5 TSOP22.., TSOP24.. Vishay Semiconductors IR Receiver Modules for Remote Control Systems PACKAGE DIMENSIONS in millimeters 13655 www.vishay.com 6 Document Number: 82095 Rev. 2.2, 20-Aug-10 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1