NH82443BXE - Intel - Product.Network

Intel® 440BX AGPset:

82443BX Host Bridge/Controller

Datasheet

April 1998

Order Number: 290633-001

82443BX Host Bridge

Datasheet

Information in this document is provided in connection with Intel products. No license, express or implied, by estoppel or otherwise, to any intellectual

property rights is granted by this document. Except as provided in Intel's Terms and Conditions of Sale fo r such products, Intel assumes no liability

whatsoever, and Intel disclaims any express or implied warranty, relating to sale and/or use of Intel products including liability or warranties relating to

fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellect ual property right. Intel products are not

intended for use in medical, life saving, or life sustaining applications.

Intel may make changes to specifications and product descriptions at any time, without notice.

Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order.

The 82443BX chipset may contain design defects or errors known as errata which may cause the product to deviate from published specifications.

Current characterized errata are available upon request.

I2C is a two-wire communications bus/protocol developed by Philips. SMBus is a subset of the I2C bus/protocol and was developed by Intel.

Implementations of the I2C bus/protocol or the SMBus bus/protocol ma y require licenses from various entities, including Philips Electronics N.V. and

North American Philips Corporation.

Copies of documents which have an ordering number and are referenced in this document, or other Intel literature may be obtained by:

calling 1-800-548-4725 or

by visiting Intel's website at http://www.intel.com.

*Third-party brands and names are the property of their respective owners.

82443BX Host Bridge

Datasheet

iii

Intel 82443BX Features

The Intel® 440BX A GPset is intended for the Pentium® II processor platform and emer ging 3D

graphics/multimedia applications. The 82443BX Host Bridge provides a Host-to-PCI bridge,

optimized DRAM controller and data path, and an Accelerated Graphic Port (AGP) interface.

AGP is a high performance, component level interconnect targeted at 3D graphics applications

and is based on a set of performance enhancements to PCI. The I/O subsystem portion of the

•Processor/host bus support

— Optimized for Pentium® II

processor at 100 MHz system bus

frequency; Support for 66 MHz

— Supports full symmetric

Multiprocessor (SMP) Protocol for

up to two processors; I/O APIC

related buffer management support

(WSC# signa l )

— In-order transact i on and dyn ami c

deferred transaction support

— Desktop optimized GTL+ bus driver

technology (gated GTL+ receivers

for reduced power)

•Inte

rated DRAM controller

— 8 to 512 Mbytes or 1GB (with

registered DIMMs)

— Supports up to 4 double-sided

DIMMs (8 rows memory)

— 64-bit data interface with ECC

support (SDRAM only)

— Unbuffered and Registered

SDRAM (Synchronous ) DRAM

Support (x-1-1 -1 access @ 66 MHz,

x-1-1-1 access @ 100 MHz)

— Enhanced SDRAM Open Page

Architecture Support for 16- and

64-Mbit DRAM devices with 2k, 4k

and 8k page sizes

•PCI bus interface

— PCI Rev. 2.1, 3.3V and 5V, 33MHz

interface compliant

— PCI Parity Generation Support

— Data streaming support from PCI to

DRAM

— Delayed Transaction support for

PCI-DRAM Reads

— Support s concu rren t CPU, AGP and

PCI transactions to main memory

•AGP interface

— Sup ports single AGP comp liant

device (AGP-66/133 3.3V device)

— AGP Specification Rev 1.0

compliant

— AGP-data/transaction flow

optimized arbitration mechanism

— A GP side-band interface for ef ficient

request pipelining without

interfering with the data streams

— AGP-specific data buffering

— Supports concurrent CPU, AGP and

PCI transactions to m a in memory

— AGP high-priority transactions

(“expedite”) support

•Power Managem ent Functions

— Stop Clock Grant and Halt special

cycle translation (host to PCI Bus)

— Mobile and “Deep Green” Desktop

support for system suspend/r e sume

(i.e., DRAM and power-on suspend)

— Dynamic po wer down o f idle DRAM

ro ws

— SDRAM self-refresh power down

support in su spen d mode

— Independent, in te rnal d ynam ic cl ock

gating reduces average power

dissipation

— Static STOP CLOCK support

— Power-on Suspend mode

— Suspend to DRAM

— ACPI compliant power management

•Packaging/Voltage

—492 Pin BGA

— 3.3V core and mixed 3.3V and G TL

I/O

•Supporting I/O Bridge

— System Management Bus (SMB)

with support for DIMM Serial

Presence Detect (SPD)

— PCI-ISA Bridge (PIIX4E)

— Power Managem ent Support

— 3.3V core and mixed 5V, 3.3V I/O

and interface to the 2.5V CPU

signals via open-drain output buffers

The 82443BX may contain design defects or errors known as errata which ma y cause the products to deviate from publ ished

specifications. Current characterized errata are available on request.

82443BX Host Bridge

Datasheet

Intel® 440BX AGPset pl atform is bas ed o n t he 8 237 1EB (P IIX4E ), a hi g hl y int egrated versi on

of the Intel’s PCI-ISA bridge f am ily. The Intel® 440BX A GPset is ideal for the Mobile A GPset

Pentium II processor platforms; providing full support for all system suspend modes and

segmented power planes.

Intel 82443BX Simplified Block Dia gram

BX_BLK.VSD

Host

Interface

A[31:3]#

ADS#

BPRI#

BNR#

CPURST#

DBSY#

DEFER#

HD[63:0]#

HIT#

HITM#

HLOCK#

HREQ[4:0]#

HTRDY#

DRDY#

RS[2:0]#

DRAM

Interface

RASA[5:0]/CSA[5:0]#

RASB[5:0]/CSB[5:0]#

CKE[3:2]/CSA[7:6]#

CKE[5:4]/CSB[7:6]#

CASA[7:0]/DQMA[7:0]

CASB[5,1]/DQMB[5,1]

GCKE/CKE1

SRAS[B,A]#

CKE0/FENA

SCAS[B,A]#

MAA[13:0]

MAB[13,12#,11#,10,9#:0#]

WEA#

WEB#

MD[63:0]

MECC[7:0]

HCLKIN

PCLKIN

GTLREF[B:A]

AGPREF

VTT[B:A]

REF5V

PCIRST#

CRESET#

BREQ0#

TESTIN#

GCLKO

GCLKIN

DCLKO

DCLKWR

AD[31:0]

C/BE[3:0]#

FRAME#

TRDY#

IRDY#

DEVSEL#

PAR

SERR#

PLOCK#

STOP#

PHOLD#

PHLDA#

WSC#

PREQ0#

PREQ[4:1]#

PGNT0#

PGNT[4:1]#

GAD[31:0]

GC/BE[3:0]#

GFRAME#

GIRDY#

GTRDY#

GSTOP#

GDEVSEL#

GREQ#

GGNT#

GPAR

PIPE#

SBA[7:0]

RBF#

STOP#

ST[2:0]

ADSTB_A

ADSTB_B

SBSTB

CLKRUN#

SUSTAT#

BXPWROK

PCI Bus

Interface

(PCI #0)

Clocks,

Reset,

Test,

and

Misc.

AGP

Interface

Power

Mgnt

82443BX Host Bridge

Datasheet

Contents

1 Architectural Overview...............................................................................................1-1

2 Signal Description......................................................................................................2-1

2.1 Host Interface Signals...................................................................................2-1

2.2 DRAM Interface ............................................................................................2-3

2.3 PCI Interface (Primary).................................................................................2-5

2.4 Primary PCI Sideband Interface ...................................................................2-6

2.5 AGP Interface Signals...................................................................................2-7

2.6 Clocks, Reset, and Miscellaneous................................................................2-9

2.7 Power-Up/Reset Strap Options...................................................................2-10

3 Register Description...................................................................................................3-1

3.1 I/O Mapped Registers...................................................................................3-2

3.1.1 CONFADD—Co nfi guration Add r ess Regi ste r............ ....... ...... ....... ..3 -2

3.1.2 CONFDATA—Configuration Data Register .....................................3-3

3.1.3 PM2_CTL—ACPI Power Control 2 Control Register.......................3-3

3.2 PCI Configuration Space Access..................................................................3-4

3.2.1 Configuration Space Mechanism Overview.....................................3-5

3.2.2 Routing the Configuration Accesses to PCI or AGP........................3-5

3.2.3 PCI Bus Configuration Mechanism Overview..................................3-6

3.2.3.1 Type 0 Access ....................................................................3-6

3.2.3.2 Type 1 Access ....................................................................3-6

3.2.4 AGP Bus Configuration Mechanism Overview ................................3-6

3.2.5 Mapping of Configuration Cycles on AGP .......................................3-7

3.3 Host-to-PCI Bridge Registers (Device 0) ......................................................3-8

3.3.1 VID—Vendor Identification Register (Device 0).............................3-10

3.3.2 DID—Device Identification Register (Device 0) .............................3-10

3.3.3 PCICMD—PCI Command Register (Device 0)..............................3-11

3.3.4 PCISTS—PCI Status Register (Device 0) .....................................3-12

3.3.5 RID—Revision Identification Register (Device 0) ..........................3-13

3.3.6 SUBC—Sub-Class Code Register (Device 0) ...............................3-13

3.3.7 BCC—Base Class Code Register (Device 0)................................3-13

3.3.8 MLT—Master Latency Timer Register (Device 0)..........................3-14

3.3.9 HDR—Header Type Register (Device 0).......................................3-14

3.3.10 APBASE—Aperture Base Configuration Register (Device 0)........3-14

3.3.11 SVID—Subsystem Vendor Identification Register (Device 0)........3-15

3.3.12 SID—Subsystem Identification Register (Device 0).......................3-16

3.3.13 CAPPTR—Capabilities Pointer Register (Device 0)......................3-16

3.3.14 NBXCFG—NBX Configuration Register (Device 0).......................3-16

3.3.15 DRAMC—DRAM Control Register (Device 0) ...............................3-19

3.3.16 DRAMT—DRAM Timing Register (Device 0) ................................3-20

3.3.17 PAM[6:0]—Programmable Attribute Map Registers (Device 0).....3-20

3.3.18 DRB[0:7]—DRAM Row Boundary Registers (Device 0)................3-22

3.3.19 FDHC—Fixed DRAM Hole Control Register (Device 0) ................3-24

3.3.20 MBSC—Memory Buffer Strength Control Register (Device 0) ......3-25

3.3.21 SMRAM—System Management RAM Control Register

(Device 0).......................................................................................3-28

82443BX Host Bridge

Datasheet

3.3.22 ESMRAMC—Extended System Management RAM Control

Registe r (Devi c e 0)....................... ....... ...... ...... ....... .......................3-29

3.3.23 RPS—SDRAM Row Page Size Register (Device 0)......................3-30

3.3.24 SDRAMC—SDRAM Control Register (Device 0) ..........................3-30

3.3.25 PGPOL—Paging Policy Register (Device 0) .................................3-32

3.3.26 PMCR—Power Management Control Register (Device 0)............3-33

3.3.27 SCRR—Su spend CBR Refres h Rate Regi ster (Devic e 0) ........ ....3 - 34

3.3.28 EAP—Error Address Pointer Register (Device 0)..........................3-35

3.3.29 ERRCMD—Error Command Register (Device 0)..........................3-36

3.3.30 ERRSTS—Error Status Register (Device 0)..................................3-37

3.3.31 ACAPID—AGP Capability Identifier Register (Device 0)...............3-38

3.3.32 AGPSTAT—AGP Status Register (Device 0)................................3-38

3.3.33 AGPCMD—AGP Command Register (Device 0)...........................3-39

3.3.34 AGPCTRL—AGP Control Register (Device 0) ..............................3-40

3.3.35 APSIZE—Aperture Size Register (Device 0).................................3-41

3.3.36 ATTBASE—Aperture Translation Table Base Register

(Device 0) ......................................................................................3-41

3.3.37 MBFS—Memory Buffer Frequency Select Register (Device 0).....3-42

3.3.38 BSPAD—BIOS Scratch Pad Register (Device 0)..........................3-44

3.3.39 DWTC—DRAM Write Thermal Throttling Control Register

(Device 0) ......................................................................................3-44

3.3.40 DRTC—DRAM Read Thermal Throttling Control Register

(Device 0) ......................................................................................3-46

3.3.41 BUFFC—Buffer Control Register (Device 0) .................................3-47

3.4 PCI-to-PCI Bridge Registers (Device 1) .....................................................3-48

3.4.1 VID1—Ve ndo r Identifi c atio n Registe r (Device 1).......... .................3 - 49

3.4.2 DID1—Device Identification Register (Device 1)...........................3-49

3.4.3 PCICMD1—PCI-to-PCI Command Register (Device 1) ................3-50

3.4.4 PCISTS1—PCI-to-PCI Status Register (Device 1)........................3-51

3.4.5 RID1—Revision Identification Register (Device 1) ........................3-51

3.4.6 SUBC1—Sub-Class Code Register (Device 1) .............................3-52

3.4.7 BCC1—Base Class Code Register (Device 1)..............................3-52

3.4.8 MLT1—Master Latency Timer Register (Device 1)........................3-52

3.4.9 HDR1—Header Type Register (Device 1).....................................3-53

3.4.10 PBUSN—Primary Bus Number Register (Device 1)......................3-53

3.4.11 SBUSN—Secondary Bus Number Register (Device 1).................3-53

3.4.12 SUBUSN—Subordinate Bus Number Register (Device 1)............3-54

3.4.13 SMLT—Secondary Master Latency Timer Register (Device 1).....3-54

3.4.14 IOBASE—I/O Base Address Register (Device 1)..........................3-54

3.4.15 IOLIMIT—I/O Limit Address Register (Device 1)...........................3-55

3.4.16 SSTS—Secondary PCI-to-PCI Status Register (Device 1) ...........3-55

3.4.17 MBASE—Memory Base Address Register (Device 1)...................3-57

3.4.18 MLIMIT—Memory Limit Address Register (Device 1)....................3-57

3.4.19 PMBAS E —Pr ef etchable Memory Bas e Add ress Regis te r

(Device 1) ......................................................................................3-58

3.4.20 PMLIMIT—Prefetchable Memory Limit Address Register

(Device 1) ......................................................................................3-58

3.4.21 BCTRL—PCI-to-PCI Bridge Control Register (Device 1) ..............3-59

82443BX Host Bridge

Datasheet

vii

4 Functional Description ...............................................................................................4-1

4.1 System Address Map....................................................................................4-1

4.1.1 Memory Address Ranges ................................................................4-2

4.1.1.1 Compatibility Area...............................................................4-3

4.1.1.2 Extended Memory Area......................................................4-4

4.1.1.3 AGP Memory Address Range.............................................4-6

4.1.1.4 AGP DRAM Graphics Aperture...........................................4-6

4.1.1.5 System Management Mode (SMM) Memory Range...........4-6

4.1.2 Memory Shadowing .........................................................................4-8

4.1.3 I/O Address Space...........................................................................4-8

4.1.4 AGP I/O Address Mapping...............................................................4-8

4.1.5 Decode Rules and Cross-Bridge Address Mapping ........................4-9

4.1.5.1 PCI Interface Decode Rules ...............................................4-9

4.1.5.2 AGP Interface Decode Rules..............................................4-9

4.1.5.3 Legacy VGA Ranges ........................................................4-10

4.2 Host Interface..............................................................................................4-10

4.2.1 Host Bus Device Support...............................................................4-10

4.2.2 Symmetric Multiprocessor (SMP) Protocol Support.......................4-13

4.2.3 In-Order Queue Pipelining.............................................................4-13

4.2.4 Frame Buffer Memory Support (USWC)........................................4-13

4.3 DRAM Interface ..........................................................................................4-14

4.3.1 DRAM Organization and Configuration..........................................4-14

4.3.1.1 Configurati on Mec ha nism For DIMMS....................... .......4-19

4.3.2 DRAM Address Translation and Decoding....................................4-20

4.3.3 SDRAMC Register Programming ..................................................4-23

4.3.4 DRAMT Register Programming.....................................................4-23

4.3.5 SDRAM Paging Policy ...................................................................4-24

4.4 PCI Interface...............................................................................................4-24

4.5 AGP Interface .............................................................................................4-24

4.6 Data Integrity Support.................................................................................4-25

4.6.1 Data Integrity Mode Selection........................................................4-25

4.6.1.1 Non-ECC (Default Mode of Operation).............................4-25

4.6.1.2 EC Mode...........................................................................4-25

4.6.1.3 ECC Mode ........................................................................4-25

4.6.1.4 ECC Generation and Error Detection/Correction

and Reporting ...................................................................4-26

4.6.1.5 Optimum ECC Coverage ..................................................4-27

4.6.2 DRAM ECC Error Signaling Mechanism........................................4-27

4.6.3 CPU Bus Integrity ..........................................................................4-27

4.6.4 PCI Bus Integrity............................................................................4-27

4.7 System Clocking.........................................................................................4-28

4.8 Power Management....................................................................................4-28

4.8.1 Overview........................................................................................4-28

4.8.2 82443BX Reset..............................................................................4-32

4.8.2.1 CPU Reset........................................................................4-33

4.8.2.2 CPU Clock Ratio Straps....................................................4-33

4.8.2.3 82443BX Straps................................................................4-34

4.8.3 Suspend Resume ..........................................................................4-34

4.8.3.1 Suspend Resume protocols..............................................4-34

4.8.3.2 Suspend Refresh ..............................................................4-34

4.8.4 Clock Control Functions.................................................................4-35

4.8.5 SDRAM Power Down Mode...........................................................4-36

viii

82443BX Host Bridge

Datasheet

4.8.6 SMRAM .........................................................................................4-36

5 Pinout and Package Information................................................................................5-1

5.1 82443BX Pinout............................................................................................5-1

5.2 Package Dim ens io ns........................... ......................... ................................5-8

Figures

1-1 Intel® 440BX AGPset System Block Diagram .............................................1-2

3-1 82443BX PCI Bus Hierarchy ........................................................................3-5

3-2 SDRAM DIMMs and Corresponding DRB Registers..................................3-23

4-1 Memory System Address Space ..................................................................4-2

4-2 Four-DIMM Configuration with FET switches .............................................4-16

4-3 Three-DIMM SDRAM Configuration ...........................................................4-17

4-4 Three-SODIMMs EDO Configuration .........................................................4-18

4-5 Three-SODIMMs SDRAM Configuration ....................................................4-19

4-6 Typical Intel® 440BX AGPset System Clocking..........................................4-28

4-7 Reset CPURST# in a Desktop or Mobile System When

PCIRST# Asserted .....................................................................................4-33

4-8 External Glue Logic Drives CPU Clock Ratio Straps..................................4-34

5-1 82443BX Pinout (Top View–left side)...........................................................5-2

5-2 82443BX Pinout (Top View–right side).........................................................5-3

5-3 82443BX BGA Package Dimensions—Top and Side Views........................5-8

5-4 82443BX BGA Package Dimensions—Bottom Views..................................5-9

82443BX Host Bridge

Datasheet

Tables

2-1 Host Interface Signals...................................................................................2-1

2-2 Host Signals Not supported by the 82443BX................................................2-3

2-3 DRAM Interface Signals................................................................................2-3

2-4 Primary PCI Interface Signals.......................................................................2-5

2-5 Primary PCI Sideband Interface Signals.......................................................2-6

2-6 AGP Interface Signals...................................................................................2-7

2-7 Clocks, Reset, and Miscellaneous................................................................2-9

2-8 Power Management Interface.......................................................................2-9

2-9 Reference Pins ...........................................................................................2-10

2-10 Strapping Options.......................................................................................2-11

3-1 82443BX Register Map — Device 0.............................................................3-8

3-2 Attribute Bit Assignment..............................................................................3-21

3-3 PAM Registers and Associated Memory Segments ...................................3-21

3-4 82443BX Configuration Space—Device 1..................................................3-48

4-1 Memory Segments and their Attributes.........................................................4-3

4-2 SMRAM Decoding ........................................................................................4-7

4-3 SMRAM Range Decode................................................................................4-7

4-4 SMRAM Decode Control...............................................................................4-7

4-5 Host Bus Transactions Supported By 82443BX.........................................4-11

4-6 Host Responses supported by the 82443BX..............................................4-12

4-7 Host Special Cycles with 82443BX.............................................................4-12

4-8 Sample Of Possible Mix And Match Options For 6 Row/3

DIMM Configurations..................................................................................4-15

4-9 Data Bytes on DIMM Used for Programming DRAM Registers..................4-20

4-10 Supported Mem ory Confi gurat ion s... ...... ....... ...... ...... ....... ...... ....... ...... .......4-21

4-11 MA Muxing vs. DRAM Address Split...........................................................4-22

4-12 Programmable SDRAM Timing Parameters...............................................4-23

4-13 EDO DRAM Timing Parameters.................................................................4-23

4-14 Low Power Mode........................................................................................4-31

4-15 AGPset Reset.............................................................................................4-32

4-16 Reset Signals..............................................................................................4-32

4-17 Suspend / Resume Events and Activities...................................................4-34

4-18 SDRAM Suspend Refresh Configuration Modes........................................4-35

5-1 82443BX Alphabetical BGA Pin List.............................................................5-4

5-2 82443BX Package Dimensions (492 BGA) ..................................................5-9

82443BX Host Bridge Datasheet

1-1

Architectural Overview

The Intel® 440BX AGPset includes the 82443BX Host Bridge and the 82371EB PIIX4E for the

I/O subsystem. The 82443BX functions and capabilities include:

•Support for single and dual Pentium II processor configurations

•64-bit GTL+ based Host Bus Interface

•32-bit Host address Support

•64-bit Main Memory Interface with optimized support for SDRAM at 100 and 66/60 MHz

•32-bit Primary PCI Bus Interface (PCI) with integrated PCI arbiter

•AGP Interface (AGP) with 133 MHz data transfer capability configurable as a Secondary PCI

Bus

•Extensi ve Data Buffering between all inte rf aces for h i gh thr oug hp ut and co ncur rent o peration s

•Mobile and “Deep Gr een ” Desktop power management support

Figure 1-1 shows a block diagram of a typical platform based on the Intel® 440BX AGPset. The

82443BX host bus interface supports up to two Pentium II processors at the maximum bus

frequenc y of 100 MHz. The physical interface d esign is based on the GTL+ specif ication optimized

for the desktop. The 82443BX provides an optimized 64-bit DRAM interface. This interface is

implemented as a 3.3V-only interface that supports only 3V DRAM technology. Two copies of the

MA, and CS# signals drive a maximum of two DIMMs each; providing unbuffered high

performance at 100 MHz. The 82443BX provides interface to PCI operating at

33 MHz. This interface implementation is compliant with PCI Rev 2.1 Specification. The

82443BX AGP interface implementation is based on Rev 1.0 of the AGP Specification. The AGP

interface supports 133 MHz data transfer rates and can be used as a Secondary PCI interface

operating at 66 MHz/3.3V supporting only a single PCI agent.

The 82443BX is designed to support the PIIX4E I/O bridge. PIIX4E is a highly integrated

multifunctio nal component supporting the fo llowing functions and capabiliti es:

•PCI Rev 2.1 compliant PCI-ISA Bridge with support for both 3.3V and 5V 33 MHz PCI

operations

•Deep Green Desktop Power Management Support

•Mobile Po wer Management Suppo rt

•Enhanced DMA controller and Interrupt Controller and Timer functions

•Integrated IDE controller with Ultra DMA/33 support

•USB host interface with support for 2 USB ports

•System Management Bus (SMB) with support for DIMM Serial PD

•Support for an external I/O APIC component

Architectural Overview

1-2

82443BX Host Bridge Datasheet

Host Interf ace

The Pentium II processor supports a second level cache via a back-side bus (BSB) interface. All

control for the L2 cache is handled by the processor. The 82443BX provides bus control signals

and address paths f or transfers between th e pro cessors f ront-sid e bus (host b us), PCI bus, AGP and

main memory. The 82443BX supports a 4-deep in-order queue (i.e., supports pipelining of up to 4

outstanding transaction requests on the host bus). Due to the system concurrency requirements,

along with support for pipelining of address requests from the host bus, the 82443BX supports

request queuing for all three interfaces (Host, AGP and PCI).

Host-init iated I/O cycles are decoded to PCI, AGP or PCI configuration space. Host-initiated

memory cycles are decoded to PCI, AGP (prefetchable or non-prefetchable memory space) or

DRAM (including AGP aperture memory). For memory cycles (host, PCI or AGP initiated) th at

target the AGP aperture space in DRAM, the 82443BX translates the address using the AGP

address translation table. Other host cycles forwarded to A G P are defined b y the A GP address map.

PCI and AGP initiated cycles that target the AGP graphics aperture are also translated using the

AGP aperture translation table. AGP-initiated cycles that target the AGP graphics aperture map ped

in main memory do not require a snoop cy cle on the host bus, since the coherency of data for that

particular memory range will be maintained by the software.

Figure 1-1. Intel® 440B X AGPset System Block Diagram

sys_blk.vsd

Video BIOS

Host Bus

82443BX

Host Bridge Main

Memory

Pentium

Processor Pentium

Processor

3.3V EDO &

SDRAM Support

2X AGP Bus

Graphics

Device

Display

ISA Bus

ISA Slots

System BIOS

System MGMT (SM) Bus

2 IDE Ports

(Ultra DMA/33)

2 USB

Ports USB

USB

APIC

82371EB

(PIIX4E)

(PCI-to-ISA

Bridge)

Primary PCI Bus

(PCI Bus #0)

PCI Slots

Encoder

Graphics

Local Memory

Video

- DVD

- Camera

- VCR

- VMI

- Video Capture

66/100

MHz

82443BX Host Bridge Datasheet

1-3

Architectural Overview

DRAM Interface

The 82443BX integrates a DRAM controller that supports a 64-bit main memory interface. The

DRAM controller supports the following features:

•DRAM type: Extended Data Out (EDO) (mobile only) or Synchronous (SDRAM) DRAM

controller optimized fo r dual/qua d-bank SDRAM organi zation on a row by row basis

•Memo ry Si ze : 8 MB to 512 MB (1GB with Registered DIMMs) with eight memory rows

•Addressing Type : Symmetrical and Asymmetrical addressing

•Memory Mo dul es supp or ted : Single and double density 3.3V DIMMs

•DRAM device technology: 16 Mbit and 64 Mbit

•DRAM Speeds: 60 ns for EDO and 100/66 MHz for synchronous memory (SDRAM).

The Intel® 440BX AGPset also pro vid es DIMM plug-and-p lay suppo rt via Serial Presence Detect

(SPD) mechanism using the SMBus interface. The 82443BX provi des optional data integrity

features including ECC in the memory array. During reads from DRAM, the 82443BX provides

error checking and correction of the data. The 82443BX supports multiple-bit error detection and

single-bi t error correction when ECC mode is enabled and single/multi-bi t error detection when

correction is disabled. During writes to the DRAM, the 82443BX generates ECC for the data on a

QWord basis. Partial QWord writes require a read-modify-write cycle when ECC is enabled.

AGP Interface

The 82443BX AGP impl ementatio n is compatible with the following:

•The Accelerated Graphics Port Specification, Rev 1.0

•Accelerated Graphics Port Memory Performance Specification, Rev 1.0 (4/12/96)

The 82443BX supports only a synchronous AGP interface coupling to the 82443BX core

frequency. The AGP interface can reach a theoretical ~500 MByte/sec transfer rate (i.e., using

133 MHz AGP compliant de v ic es).

PCI Interface

The 82443BX PCI interface is 3.3V (5V tolerant), 33 MHz Rev. 2.1 compliant and supports up to

five external PCI bus masters in addition to the I/O bridge (PIIX4/PIIX4E). The PCI-to-DRAM

interface can reach over 100 MByte/sec transfer rate for streaming reads and over 120 MBytes/sec

for streaming writes.

System Clocking

The 82443BX operates the host interface at 66 or 100 MHz, the SDRAM/core at 66 or 100 MHz,

PCI at 33 MHz and AGP at 66/133 MHz.

I/O APIC

I/O APIC is used to support dual processors as well as enhanced interrupt processing in the single

processor environment. The 82443BX supports an external status output signal that can be used to

control synchronization of interru pt s in conf i g urat ion s th at use PIIX 4E with stan d-alon e I/O APIC

component.

82443BX Host Bridge Datasheet

2-1

Signal Des cr i pti on

Signal Description

This chapter provides a detailed description of 443BX signals. The signals are arranged in

functional groups according to their associated interface.

The “#” symbol at the end of a signal name indicates that the active, or asserted state occurs when

the signal is at a low voltage level. When “#” is not present after the signal name the signal is

asserted when at the high voltage level.

The following notati ons are used to describe the signal t ype:

IInpu t pi n

OOutput pin

OD Open Drain Output pin. This pin requires a pullup to the VCC of the processor core

I/OD Input / Open Drain Output pin . This pin requ ires a pullup to the VC C of t he processo r

core

I/O Bi-directional Input/Output pin

The signal description also includes the type of buffer used for the particular signal:

GTL+ Open Drain GTL+ interface signal. Refer to the GTL+ I/O Specif i cation for complete

details

PCI PCI bus interface signals. These signals are compliant with the PCI 3.3V and 5.0V

Signaling Environment DC and AC Specifications

AGP AGP interface signals. These signals are compatible with AG P 3.3V Signaling

Environment DC and AC Specifications

CMOS The CMOS buffers are Low Voltage TTL compatible signals. These are 3.3V only.

2.1 Host Interface Signals

Table 2-1. Host Interface Signals (Sheet 1 of 2)

Name Type Description

CPURST# O

GTL+

CPU Reset. The CPURST# pin is an output from the 82443BX. The 82443BX

generates this signal based on the PCIRST# input (from PIIX4E) and also the

SUSTAT# pin in mobile mode. The CPURST# allows the CPUs to begin execution in

a known state.

A[31:3]# I/O

GTL+ Address Bus: A[31:3]# connect to the CPU address bus. During CPU cycles, the

A[31:3]# are inputs.

HD[63:0]# I/O

GTL+ Host Data: These signals are connected to the CPU data bus. Note that the data

signals are inverted on the CPU bus.

Signal Description

2-2

82443BX Host Bridge Datasheet

NOTE:

1. All of the signals in the host interface are descr ibed in the CPU External Bus Specification. The preceding

table highlights 82443BX specific uses of these signals.

ADS# I/O

GTL+ Address Strobe: The CPU bus owner asserts AD S# to indicate the first of two

cycles of a request phase.

BNR# I/O

GTL+ Block Next Request: Used to block the current request bus owner from issuing a

new request. This signal is used to dynamically control the CPU bus pipeline depth.

BPRI# O

GTL+

Priority Agent Bus Request: The 82443BX is the only Priority Agent on the CPU

bus . It asserts this signal to obtain t he ownership of the address bus. This signal has

prior ity over symmetric bus requests and will cause the current symmetric owner to

stop issuing new transactions unless the HLOCK# signal was asser ted.

BREQ0# O

GTL+

Symmetric Agent Bus Request: Asserted by the 82443BX when CPURST# is

asserted to configure the symmetr ic bus agents. BREQ0# is negated 2 host clocks

after CPURST# is negated.

DBSY# I/O

GTL+ Data Bus Busy: Used by the data bus owner to hold the data bus for tr ansfers

requiring more than one cycle.

DEFER# O

GTL+

Defer: The 82443BX generates a deferred response as defined by the rules of the

82443BX’s dynamic defer policy. The 82443BX also uses the DEFER# signal to

indicate a CPU retry response.

DRDY# I/O

GTL+ Data Read y: Asserted for each cycle that data is transferred.

HIT# I/O

GTL+ Hit: Indicates that a caching agent holds an unmodified v ersion of the requested li ne.

Also driven in conjunction with HITM# by the target to extend the snoop window.

HITM# I/O

GTL+

Hit Modifi ed : Indicates that a caching agent holds a modified version of the

requested line and that this agent assumes responsibility for providing the line. Also

driven in conjunction with HIT# to extend the snoop window.

HLOCK# I

GTL+

Host Lock: All CPU bus cycles sampled with the assertion of HLOCK# and ADS#,

until the negation of HLOCK# must be atomic, i.e. no PCI or A GP snoopable access

to DRAM is allo wed when HLOCK# is asserted by the CPU .

HREQ[4:0]# I/O

GTL+

Request Command: Asserted during both clocks of request phase. In the first clock,

the signals define the transaction type to a level of detail that is sufficient to begin a

snoop request. In the second clock, the signals carry additional inf ormation to define

the complete transaction type. The transactions supported by the 82443BX Host

Bridge are defined in the Host Interface section of this document.

HTRDY# I/O

GTL+ Host Targ et Ready: Indicates that the target of the CPU transaction is able to enter

the data transfer phase.

RS[2:0]# I/O

GTL+

Response Signals: Indicates type of response according to the following the table:

RS[2:0] Response type

000 Idle state

001 Retry response

010 Deferred response

011 Reserved (not driven by 82443BX)

100 Hard Failure (not driven by 82443BX)

101 No data response

110 Implicit Writeback

111 Normal data response

Table 2-1. Host Interface Signals (Sheet 2 of 2)

Name Type Description

82443BX Host Bridge Datasheet

2-3

Signal Des cr i pti on

Table 2-2 lists the CPU bus interface signals which are NOT supported by the Intel® 440B X

AGPset.

2.2 DRAM Interface

Table 2-2. Host Signals Not supported by the 82443BX

Signal Function Not Supported By 82443BX

A[35:32]# Address Extended addressing (over 4 GB)

AERR# Address Parity Error Parity protection on address bus

AP[1:0]# Ad dress Parity Parity protection on address bus

BINIT# Bus Initialization Checking for bus protocol violation and protocol recovery mechanism

DEP[7:0]# Data Bus ECC/Parity Enhanced data bus integrity

IERR# Internal Err or Direct internal error observation via IERR# pin

INIT# Soft Reset Implemented by PIIX4E, BIST supported by external logic.

BERR# Bus Error Unrecoverable error without a bus protocol violation

RP# Request Parity Parity protection on ADS# and PREQ[4:0]#

RSP# Response Parity

Signal Parity protection on RS[2:0]#

Table 2-3. DRAM Interface Signals (Sheet 1 of 2)

Name T

eDescri

tion

RASA[5:0]#

/CSA[5:0]#

RASB[5:0]#

/CSB[5:0]#

CMOS

Row Ad dress Strobe (EDO): These signals are used to latch the ro w address on

the MAxx lines into the DRAMs. Each signal is used to select one DRAM row.

These signals drive the DRAM array directly without any exter n al buffers.

Chip Select (SDRAM): For the memory row configured with SDRAM these pins

perform the function of selecting the par ticular SDRAM components dur ing the

active state.

Note that there are 2 copies of RAS# per physical memory row to improve the

CKE[3:2]

/CSA[7:6]#

CKE[5:4]

/CSB[7:6]#

CMOS

Clock Enable: In mobile mode, SDRAM Clock Enable is used to signal a self-

refresh or power-down command to an SDRAM array when entering system

suspend. CKE is also used to dynamically power dow n inactive SDRAM rows.

This CKE function is not supported with Registered DIMMs.

Chip Select (SDRAM): These pins perform the function of selecting the

particular SDRAM components during the active state.

Note that there are 2 copies of CS# per physical memor y row to reduce the

CASA[7:0]#

/DQMA[7:0] O

CMOS

Column Address Strobe A-side (EDO): The CASA[7:0]# signals are used to

latch the column address on the MA[13:0] lines into the DRAMs of the A half of

the memory arra y. These are active low signals that drive the DRAM array directly

without ex ternal buffering.

Input/Output Data Mask A-side (SDRAM): These pins control A half of the

memory array and act as synchronized output enables during read cycles and as

a byte enables during write cycles.

CASB[1,5]#

/DQMB[1,5] O

CMOS

Column Address Strobe B-side (EDO) / Input/Output Data Mask B-side

(SDRAM): The same function as a corresponding signals for A side. These

signals are used to reduce the loading in an ECC configuration

Signal Description

2-4

82443BX Host Bridge Datasheet

GCKE/CKE1 O

CMOS

Global CKE (SDRAM): Global CKE is used in a 4 DIMM configuration requiring

power down mode f or the SDRAM. External logic must be used to implement this

function.

SDRAM Cloc k Enable (CKE1): In mobile mode, SDRAM Cloc k Enable is used to

signal a self-refresh or power-do wn command to an SDRAM arra y when entering

system suspend. CKE is also used to dynamically power down inactive SDRAM

rows. The combination of SDRAMPWR (SDRAM register) and MMC ONFIG

(DRAMC register) determine the functioning of the CKE signals. Refer to the

DRAMC register (Section 3.3.15, “DRAMC —DRA M Control Register (Device 0)”

on page 3-19) for more details.

SRAS[B,A]# O

CMOS

SDRAM Row Address Strobe (SDRAM): The SRAS[B,A]# signals are multiple

copies of the same logical SRASx signal (for loading purposes) used to generate

SDRAM comm and encoded on SRASx/SCASx/WE signals.

CKE0/FENA O

CMOS

SDRAM Clock Enable 0 (CKE0). In mobile mode, CKE0 SDRAM Clock Enable

is used to signal a self-refresh or power-down command to an SDRAM array

when entering system suspend. CKE is also used to dynamically power down

inactive SDRAM rows.

FET En able (F ENA): In a 4 DIMM configuration. FENA is used to select the

proper MD path through the FET switches (ref er to Section 4.3, “DRAM Interf ace”

on page 4-14 for more details).

SCAS[B,A]# O

CMOS

SDRAM Column Address Strobe (SDRAM): The SCAS[B,A]# signals are

multiple copies of the same logical SCASx signal (for loading purposes) used to

generate SDRAM command encoded on SRASx/SCASx/WE signals.

MAA[13:0]

MAB[12:11]#

MAB[13,10]

MAB[9:0]#

CMOS

Memory Address(EDO/SDRAM): MAA[13:0] and MAB[13:0]# are used to

provide the multiplexed row and column address to DRAM. There are two sets of

MA signals which drive a max. of 2 DIMMs each. MAA[12:11,9:0] are inver ted

copies of MAB[12:11,9:0]#. MAA[13,10] and MAB[13,10] are identical copies.

Each MAA/MAB[13:0] line has a programmable buffer strength to optimize for

different signal loading conditions.

WEA#

WEB# O

CMOS

Write Enable Signal (EDO/SDRAM): WE# is asserted during writes to DRAM.

The WE# lines have a progr ammable buffer strength to optimize for different

signal loading conditions.

MD [63:0] I/O

CMOS Memory Data (EDO/SDRAM): These signals are used to interface to the DRAM

data bus.

MECC[7:0] I/O

CMOS Memory ECC Data (EDO/SDRAM): These signals carry Memory ECC data

during access to DRAM.

Table 2-3. DRAM Interface Signals (Sheet 2 of 2)

Name T

pe Description

82443BX Host Bridge Datasheet

2-5

Signal Des cr i pti on

2.3 PCI Interface (Primary)

Table 2-4. Primary PCI Interface Signals (Sheet 1 of 2)

Name Type Description

AD[31:0] I/O

PCI

PCI Address/Data: These signals are connected to the PCI address/data bus.

Address is driven by the 82443BX with FRAME# assertion, data is driven or received

in the following clocks. When the 82443BX acts as a target on the PCI Bus, the

AD[31:0] signals are inputs and contain the address during the first clock of FRAME#

assertion and input data (writes) or output data (reads) on subsequent clocks.

DEVSEL# I/O

PCI

Device Select: Device select, when asserted, indicates that a PCI target device has

decoded its address as the target of the current access. The 82443BX asser t s

DEVSEL# based on the DRAM address range or

A GP address range

being accessed

by a PCI initiator. As an input it indicates whether any device on the bus has been

selected.

FRAME# I/O

PCI

Frame: FRAME# is an output when the 82443BX acts as an initiator on the PCI Bus.

FRAME# is asserted by the 82443BX to indicate the beginning and duration of an

access. The 82443BX asserts FRAME# to indicate a bus transaction is beginning.

While FRAME# is asserted, data transfers continue. When FRAME# is negated, the

transaction is in the final data phase. FRAME# is an input when the 82443BX acts as

a PCI target. As a PCI target, the 82443BX latches the C/BE[3:0]# and the AD[31:0]

signals on the first clock edge on which it samples FRAME# active.

IRDY# I/O

PCI

Initiator Ready: IRDY# is an output when 82443BX acts as a PCI initiator and an

input when the 82443BX acts as a PCI target. The assertion of IRDY# indicates the

current PCI Bus initiator's ability to complete the current data phase of the

transaction.

C/BE[3:0]# I/O

PCI

Command/Byte Enable: PCI Bus Command and Byte Enable signals are

multiplexed on the same pins. During the address phase of a transaction, C/BE[3:0]#

define the bus command. During the data phase C/BE[3:0]# are used as b yte

enables. The byte enables deter m ine which byte lanes carry meaningful data. PCI

Bus command encoding and types are listed below.

C/BE[3:0]# Command Type

0000 Interrupt Acknowledge

0001 Special Cycle

0010 I/O Read

0011 I/O Write

0100 Reser ved

0101 Reser ved

0110 Memory Read

0111 Memory Write

1000 Reser ved

1001 Reser ved

1010 Configuration Read

1011 Configuration Write

1100 Memory Read Multipl e

1101 Reserved (Dual Address Cycle)

1110 Memory Read Line

1111 Memory Write and Invalidate

PAR I/O

PCI

P arity: PAR is dr iven by the 82443BX when it acts as a PCI initiator during address

and data phases f or a write cycle , and during the address phase for a read cycle. PAR

is driven by the 82443BX when it acts as a PCI target during each data phase of a

PCI memory read cycle. Even parity is generated across AD[31:0] and C/BE[3:0]#.

PLOCK# I/O

PCI

Lock: PLOCK# indicates an exclusive bus operation and may require multiple

transactions to complete. When PLOCK# is asserted, non-e xclusive tr ansactions ma y

proceed. The 82443BX supports lock for CPU initiated cycles only. PCI initiated

locked cycles are not supported.

TRDY# I/O

PCI

Target Ready: TRDY# is an input when the 82443BX acts as a PCI initiator and an

output when the 82443BX acts as a PCI target. The assertion of TRDY# indicates the

target agent's ability to complete the current data phase of the transaction.

Signal Description

2-6

82443BX Host Bridge Datasheet

NOTE:

1. All PCI interface signals conform to the PCI Rev 2.1 specification.

2.4 Primary PCI Sideband Interface

SERR# I/O

PCI

System Error: The 82443BX asserts this signal to indicate an error condition. The

SERR# assertion by the 82443BX is enabled globally via SERRE bit of the PCICMD

In an ECC configuration, the 82443BX asserts SERR#, for single bit (correctable)

ECC errors or multiple bit (non-correctable) ECC errors if SERR# signaling is enabled

via the ERRCMD control register . An y ECC errors received during initialization should

be ignored.

• The 82443BX asserts SERR# for one clock when it detects a target abort during

82443BX initiated PCI cycle .

• The 82443BX can also assert SERR# when a PCI parity error occurs during the

address or data phase.

• The 82443BX can assert SERR# when it detects a PCI address or data parity

error on AGP.

• The 82443BX can assert SERR# upon detection of access to an invalid entry in

the Graphics Aperture Translation Table.

• The 82443BX can assert SERR# upon detecting an invalid AGP master access

outside of AGP aperture and outside of main DRAM range (i.e. in the 640k - 1M

range or above TOM).

• The 82443BX can assert SERR# upon detecting an invalid AGP master access

outside of AGP aperture.

• The 82443BX asserts SERR# for one clock when it detects a target abort during

82443BX initiated AGP cycle.

STOP# I/O

PCI

Stop: STOP# is an input when the 82443BX acts as a PCI initiator and an output

when the 82443BX acts as a PCI target. STOP# is used for disconnect, retr y, and

abort sequences on the PCI Bus.

Table 2-4. Primary PCI Interface Signals (Sheet 2 of 2)

Name Type Description

Table 2-5. Primar

PCI Sideband Interface Signals

Name Type Description

PHOLD# I

PCI

PCI Hold: This signal comes from the PIIX4E. It is the PIIX4E request for PCI bus

ownership. The 82443BX will flush and disable the CPU-to-PCI write buffers before

granting the PIIX4E the PCI bus via PHLDA# . This prevents bus deadlock between

PCI and ISA.

PHLDA# O

PCI PCI Hold Acknowledge: This signal is driven by the 82443BX to grant PCI bus

ownership to the PIIX4E after CPU-PCI post buff ers ha ve been flushed and disabled.

WSC# O

CMOS

Write Snoop Complete. This signal is asser ted active to indicate that all that the

snoop activity on the CPU bus on the behalf of the last PCI-DRAM write transaction is

complete and that is safe to send the APIC interrupt message.

PREQ[4:0]# I

PCI PCI Bus Request: PREQ[4:0]# are the PCI bus request signals used as i nputs b y the

inter nal PCI arbiter.

PGNT[4:0]# O

PCI PCI Grant: PGNT[4:0]# are the PCI bus gr ant output signals gener ated b y the internal

PCI arbiter.

82443BX Host Bridge Datasheet

2-7

Signal Des cr i pti on

2.5 AGP Interface Signals

There are 17 ne w signals added to the normal PCI group of signals that together constitute the AGP

interface. The sections below describe their operation and use, and are organized in five groups:

•AG P Addressing Signals

•AGP Flow Control Signals

•AGP Status Signals

•AG P Clocking Signals - Strobes

•PCI Signals

Table 2-6. AGP Interface Signals (Sheet 1 of 2)

Name Type Description

AGP Sideband Addressing Signals1

PIPE# I

AGP

Pipelined Read:

This si

nal is asserted b

the current master to indicate a full width

address is to be

ueued b

the tar

et. The master

ueues one re

uest each risin

clock ed

e while PIPE# is asserted. When PIPE# is deasserted no new requests are

queued across the AD bus. PIPE# is a sustained tri-state signal from

masters

(graphics controller)

and is an input to the 82443BX. Note that initial AGP designs

may not use PIPE#.

SBA[7:0] I

AGP

Sideband Address: This bus

provides an additional bus to pass address and

command to the 82443BX from the AG P mas ter. Note that, when sideband

addressing is disabled, these signals are isolated (no ex ternal/internal pull-ups are

required).

AGP Flow Control Sign a ls

RBF# I

AGP

Read Buffer Full.

This si

nal indicates if the master is read

to accept previousl

uested low priorit

read data. When RBF# is asserted the 82443BX is not allowed

to return low priority read data to the AGP mas ter on the first block. RBF# is only

sampled at the beginning of a cycle.

If the AGP master is always ready to accept return read data then it is not required to

implement this signal.

AGP Status Signals

ST[2:0] O

AGP

Status

Bus: This bus provides information from the arbit er to a AGP Master on what

it ma

do. ST

[

2:0

]

only hav e meaning to the master when its GGNT# is asserted.

When GGNT# is deasserted these signals have no meaning and must be ignored.

000 Indicates that previously requested low priority read data is being returned to

the master.

001 Indicates that prev iously requested high priority read data is being returned to

the master.

010 Indicates that the master is to provide lo w priority write data for a previously

queued write command.

011 Indicates that the master is to provide high priority write data for a previously

queued write command.

100 Reserved

101 Reserved

110 Reserved

11 1 Indi cates that the master has been

iven permission to start a bus transaction.

Th e master ma

ueue AGP re

uests b

assertin

PIPE# or start a PCI

transaction by asserting FRAME#. ST

[

2:0

]

are alwa ys an output from the

82443BX and an input to the master.

Signal Description

2-8

82443BX Host Bridge Datasheet

NOTE:

1. AGP Sideband Addressing Signals. The above tab le contains two mechanisms to queue requests by

the AGP master. Note that the master can only use one mechanism. When PIPE# is used to queue

addresses the master is not allowed to queue addresses using the SBA bus. For example, during

configuration time, if the master indicates that it can use either mechanism, the configuration software will

indicate which mechanism the master will use. Once this choice has been made, the master will continue to

use the mechanism selected until the master is reset (and reprogrammed) to use the other mode. This

change of modes is not a dynamic me chanism but rather a static decision when the device is first being

configured after reset.

AGP Clocking Signals - Strobes

ADSTB_A I/O

AGP

AD Bus Strobe A: This si

nal provides timin

for double clocked data on the AD bus.

The agent that is providing data drives this signal. This signal requires an 8.2K ohm

exter nal pull-up resistor.

ADSTB_B I/O

AGP AD Bus Strobe B: This signal is an additional copy of the AD_STBA signal. This

signal requires an 8.2K ohm external pull-up resistor.

SBSTB I

AGP Sideband Strobe: THis signal provides timing for a side-band bus. This signal

requires an 8.2K ohm exter nal pull-up resistor.

AG P FRAME# Protocol SIgn a ls (similar to PCI)2

GFRAME# I/O

AGP Graphics Frame: Same as PCI. Not used b

AGP. GFRAME# remains deasserted

by its own pull up resistor.

GIRDY# I/O

AGP

Graphics Initiator Ready: New meanin

. GIRDY# indicates the AGP compliant

master is ready to provide

all

write data for the current transaction. Once IRDY# is

asserted for a write operation, the master is not allowed to insert wait states. The

assertion of IRDY# for reads indicates that the master is ready to transfer to a

subsequent block (32 bytes) of read data. The master is

never

allowed to insert wait

states during the initial data tr ansfer (32 bytes) of a read transaction. However, it may

insert wait states after each 32 byte block is transferred.

(There is no GFRAME# -- GIRDY# relationship for AGP transactions.)

GTRDY# I/O

AGP

Graphics Target Ready: New meanin

. GTRDY# indicates the AGP compliant

target is ready to provide read data f or the entire tr ansaction (when the transf er size is

less than or equal to 32 bytes) or is ready to transfer the initial or subsequent block

(32 bytes) of data when the transfer size is greater than 32 bytes. The target is

allowed to insert wait states after each block (32 bytes) is transferred on both read

and write transactions.

GSTOP# I/O

AGP Graphics Stop: Same as PCI. Not used by AGP.

GDEVSEL# I/O

AGP Graphics Device Select: Same as PCI. Not used by AGP.

GREQ# I

AGP Graphics Request: Same as PCI. (Used to request access to the bus to initiate a

PCI or AGP request.)

GGNT# O

AGP

Graphics Grant: Same meanin

as PCI but additional information is provided on

[

2:0

]

. The additional inf ormation indicates that the selected master is the recipient

of pre viously requested read data (high or normal priority), it is to provide write data

(high or normal prior ity), for a previously queued write command or has been given

per miss ion to start a bus transaction (AGP or PCI).

GAD[31:0] I/O

AGP Graphics Address/Data: Same as PCI.

GC/BE[3:0]# I/O

AGP

Graphics Command/Byte Enables: Sli

htl

different meanin

. Provides command

information

(

diff erent commands than PCI

)

when re

uests are bein

ueued when

usin

PIPE #. Provide valid byte information during AGP wr ite transactions and are

not used during the return of read data.

GPAR I/O

AGP Graphics Parity: Same as PCI. Not used on AGP transactions, but used during PCI

transactions as defined by the PCI specification.

Table 2-6. AGP Interface Signals (Sheet 2 of 2)

Name Type Description

82443BX Host Bridge Datasheet

2-9

Signal Des cr i pti on

2. PCI signals are redefined when used in AGP transactions carried using AGP protocol extension. For

transactions on the AGP interface carried using PCI protocol these signals completely preserve PCI

semantics. The exact role of all PCI signals during AGP transactions is in Table 2-6.

3. The LOCK# signal is not supported on the AGP interface (e ven for PCI operations).

4. PCI signals descr ibed in Table 2-4 behave according to PCI 2.1 specifications when used to perform PCI

transactions on the AGP Interface.

2.6 Clocks, Reset, and Miscellaneous

Table 2-7. Clocks, Reset, and Miscellaneous

Name Type Description

HCLKIN I

CMOS

Host Cloc k In: This pin receives a b uffered host cloc k. This clock is used by all of the

82443BX logic that is in the Host clock domain.

When SUSTAT # is active, there is an inter nal 100K ohm pull down on this signal.

PCLKIN I

CMOS

PCI Clock In: This is a buffered PCI clock ref erence that is synchronously derived by

an ex ternal clock synthesizer component from the host clock. This cloc k is used by all

of the 82443BX logic that is in the PCI clock domain.

When SUSTAT # is active, there is an inter nal 100K ohm pull down on this signal.

DCLKO O

CMOS SDRAM Clock Out: 66 or 100 MHz SDRAM clock reference. It feeds an external

buffer clock device that produces multiple copies for the DIMMs.

DCLKWR I

CMOS

SDRAM Write Clock: Feedback reference from the external SDRAM clock buffer.

This clock is used by the 82443BX when wr iting data to the SDRAM array.

Note: See the Design Guide for routing constraints.

PCIRST# I

CMOS

PCI Reset: When asserted, this signal will reset the 82443BX logic. All PCI output

and bi-directional signals will also tri-state compliant to PCI Rev 2.0 and 2.1

specifications.

When SUSTAT # is active, there is an inter nal 100K ohm pull down on this signal.

GCLKIN I

CMOS AGP Clock In: The GCLKIN input is a feedbac k reference from the GCLK OUT signal.

GCLKO O

CMOS AGP Clock Out: The frequency is 66 MHz. The GCLKOUT output is used to feed

both the refe rence input pin on the 82443BX and the AGP compliant device.

CRESET# O

CMOS

Delayed CPU Reset: CRESET# is a delayed copy of CPURST#. This signal is used

to control the multiplexer for the CPU strap signals. CRESE T# is delayed from

CPURST# by two host clocks.

Note: This pin requires an e x ternal pull-up resistor. If not used, no pull up is required.

TESTIN# I

CMOS Tes t Input: This pin is used for manufacturing, and board level test purposes.

Note: This pin has an internal 50K ohm pull-up.

Table 2-8. Power Management Interface

Name Type Description

CLKRUN# I/OD

CMOS

Primary PCI Clock Run: The 82443BX requests the central resource (PIIX4E) to start

or maintain the PCI clock by the asser tion of CLKRUN#. The 82443BX tristates

CLKRUN# upon deassertion of PCIRST# (since CLK is running upon deassertion of

reset). If connected to PIIX4E an external 2.7K Ohm pull-up is required for Desktop,

Mobile requires (8.2k–10K) pull-up. Otherwise, a 100 Ohm pull down is required.

SUSTAT# I

CMOS

Suspend Stat us (from PIIX ): SUSTAT# signals the system suspend state transition

from the PIIX4E. It is used to isolate the suspend voltage well and enter/exit DRAM

self-refresh mode. Dur ing POS/STR SU STAT# is active.

BXPWROK I

CMOS BX Power OK: BXPWROK input must be connected to the PWROK signal that

indicates valid power is applied to the 82443BX.

Signal Description

2-10

82443BX Host Bridge Datasheet

2.7 Power-Up/Reset Strap Options

Table 2-10 is the list of all power-up optio ns that are loaded into the 82443BX du ring cold reset.

The 82443BX is required to float all the signals connected to straps during cold reset and keep

them floated for a minimum of 4 host clocks after the end of cold reset sequence. Cold reset

sequence is performed when the 82443BX power is applied.

Note: All signals used to select power-up strap options are connected to either internal pull-down or pull-

up resistor s of mi ni mu m 50K ohm s (max imum is 150K). That sel ects a default mod e on th e signal

during res et. To enable d if ferent mode s, ext ernal pull ups or pull downs (the opposi te of the in ternal

resistor) of approximately 10K ohm can be connected to particular signals. These pull up or pull

down resistors should be connected to the 3.3V power supply.

During normal operation of the 82443BX, including while it is in suspend mode, the paths from

GND or Vcc to internal strapping resistors are disabled to effectively disable the resistors. In these

cases, the MAB# lines are driven by the 82443BX to a valid voltage levels.

Note: Note that when resuming from suspend, even while PCIRST# is active, the MAB# lines remain

driven by the 82443BX and the strapping latches maintain the value stored during the cold reset.

This first column in Table 2-10 lists the signal that is sampled to obtain the strapping option. Th e

second colum n s hows which register the strapping o ption is loaded into. The third column is a

description of what functionality the strapping selects.

The GTL+ signals are connected to the VTT through the normal pull-ups. CPU bus straps

controlled by the 82443BX (e.g. A7# and A15#), are driven active at least six clocks prior to the

active-to-inactive edge of CPURST# and driven inactive four clocks after the active-to-inactive

edge of the CPURST#.

Table 2-9. Reference Pins

Name Description

GTLREF[B:A] GTL Buffer voltage reference input

VTT[B:A] GTL Threshold voltage f or early clamps

VCC Power pin @ 3.3V

VSS Ground

REF5V PCI 5V reference voltage (for 5V tolerant buffers)

AGPREF External Input Reference

82443BX Host Bridge Datasheet

2-11

Signal Des cr i pti on

NOTE:

1. Proper strapping must be used to define logical v alues for these signals . Default value “0”, or “1” provided by

the internal pull-up or pull-down resistor can be overridden by the external pull-up, or pull-down resistor.

Table 2-10. Strapping Options

Signal Register

Name[bit] Description

MAB13# Reserved.

MAB12# NBXCFG[13] Host Frequency Select: If MAB#12 is strapped to 0, the host bus frequency is 60/

66 MHz. If MAB#12 is strapped to 1, the host bus frequency is 100 MHz. An

internal pull-down is used to provide the default setting of 66 MHz.

MAB11# NBXCFG[2]

In-Order Queue Depth Enable. If MAB11# is strapped to 0 during the rising edge

of PCIRST#, then the 82442BX will drive A7# low during the CPURST#

deassertion. This forces the CPU bus to be configured for non-pipelined oper ation.

If MAB11 is strapped to 1 (default), then the 82443BX does not drive th e A7# low

during reset, and A7# is sampled in def ault non-driven state (i.e . pulled-up as f ar as

GTL+ termination is concerned) then the maximum allowable queue depth by the

CPU bus protocol is selected (i.e., 8).

Note that inter nal pull-up is used to provide pipelined bus mode as a default.

MAB10 PMCR[3]

Quick Start Select. The value on this pin at reset determines which stop clock

mode is used.

MAB10 = 0 (default) for nor mal stop clock mode. If MAB10 = 1 during the rising

edge of PCIRST#, then the 82443BX will drive A15# low during CPURST#

deassertion. This will configure the CPU for Quick Start mode of operation.

Note that internal pull-down is used to provide normal stop clock mode as a default.

MAB9# PMCR[1]

A GP Disable: When strapped to a 1, the AGP interf ace is disabled, all A GP signals

are tri-stated and isolated. When strapped to a 0 (default), the AGP interface is

enabled.

When MMCONFIG is strapped active, we require that AGP_D ISABL E is also

strapped active. When MMCONFIG is strapped inactive, AGP_DISABLE can be

strapped active or inactive but IDSEL_REDIRECT (bit 16 in NBXCFG register)

must never be activated.

This signal has an internal pull-down resistor.

MAB8# Reserved.

MAB7# DRAMC[5]

Memory Module Configuration, MMCONFIG: When strapped to a 1, the

82443BX configures its DRAM interface in a 430-TX compatible manner. These

unused inputs are isolated while unused outputs are tri-stated: RASB[5:0]#/

CSB[5:0]#, CKE[3:2]/CSA[7:6]#, CKE[5:4]/CSB[7:6] #, CASB[5,1] #/DQMB[5,1],

GCKE/CKE1, MAA[13:0], DCLKO.

When strapped to a 0 (default), the 82443BX DRAM signal are used normally.

IDSEL_REDIRECT (bit 16 in NBXC FG register) is programmed by BIOS, before it

begins with dev ice enumeration process. The combination of SDRAMPWR

(SDRAMC register) and MMCONFIG (DRAMC register) determine the functioning

of the CKE signals. Refer to the DRAMC register for more details.

Note that inter nal pull-down is used to set the DRAM interface to a normal

configuration, as a default.

MAB6# none

Host Bus Buffer Mode Select: When strapped 0, the desktop GTL+ 66 MHz or

100 MHz host bus buffers are used (default).

When strapped ‘1’, the mobile Low Pow er GTL+ 66 MHz host bus buffers are

selected.

Note that inter nal pull-down is used to set the host bus buffers to a desktop

configuration as a default. External pull-up therefore is needed for mobile systems,

only.

A[15]# none Quick Start Select. The value on A15# sampled at the rising edge of CPURST#

will reflect if the quick star t/stop clock mode is enabled in the processors.

A7# none In-order Queue Depth Status. The value on A[7]# sampled at the rising edge of

CPURST# reflects if the IOQD is set to 1 or maximum allowable by the CPU bus.

82443BX Host Bridge Datasheet

3-1

The 82443BX contains two sets of software accessible registers, accessed via the Host CPU I/O

address space:

1. Control reg isters that are I/O mapped into the CPU I/O space. These re gisters co ntrol access to

PCI and AGP configuration space.

2. Inte rnal configuration registers residing within the 82443BX, partitio ned into two logical

device register sets (“logical” since they reside within a single physical device). The first

interface operations, DRAM configuration, and other chip-set operating parameters and

optional features. The second register set (device 1) is dedicated to Host-to-AGP Br idge

functions (controls AGP interface configurations and operating parameters).

The following nomenclature is used for register access attributes.

The 82443BX supports PCI configuration space access using the mechanism denoted as

Configuration Mechanism #1 in the PCI specification.

The 82443BX internal registers (both I/O Mapped and Configuration registers) are accessible by

the Host CPU. The registers can be accessed as Byte, Word (16-bit), or DWord (32-bit) quantities,

with the exception of CONFADD which can only be accessed as a Dword. All multi-byte numeric

fields use "little-endian" ordering (i.e., lower addresses contain the least significant parts of the

field).

Some of the 82443BX registers described in this section contain reserved bits. These bits are

labeled "Reserved”. Software must deal correctly with fields that are reserved. On reads, software

must use appropriate masks to extract the defined bits and not rely on reserved bits being any

particular value. On writes, software must ensure that the values of reserved bit positions are

preserved. That is, the values of reserved bit positions must first be read, merged with the new

values for other bit p os itions and then written back .

Note: Software does not need to perform read, merge, write operation for the configuration address

In addition to res e rved bits within a register, the 82443BX contains address locati ons in the

configuration space of the Host-to-PCI Bridge entity that are marked either "Reserved" or “Intel

Reserved”. The 82443BX responds to accesses to “Reserved” address locations by completing the

host cycle. When a “Reserved” register location is read, a zero value is returned. (“Reserved”

registers can be 8-, 16-, or 32-bit in size). Writes to “Reserved” registers have no effect on the

RO Read Only. If a register is read only, writes to this register have no effect.

R/W Read/Write. A register with this attribute can be read and written

R/WC Read/Write Clear. A register bit with this attribute can be read and written.

However, a write of a 1 clears (sets to 0) the corresponding bit and a write of a 0 has

no effect.

R/WO Read/Write Once. A register bit with this attribute can be written to only once after

power up. After the first write, the bit becomes read only.

R/WL Read/Write/Lock. This register includes a lock bit. Once the lock bit has been set to

1, the register becomes read only.

3-2

82443BX Host Bridge Datasheet

82443BX. Re g isters that are mark ed as “I ntel R eserv ed ” mu st not be modified by system software.

Writes to “Intel Reserved” registers may cause system failure. Reads to “Intel Reserved” registers

may return a non-zero value. Software should not write to reserved configuration locations in the

device-specific region (above address offset 3Fh)

Upon reset, the 82443BX sets its internal configuration registers to predetermined default states.

However, there are a few exceptions to this rule.

1. When a reset occurs during the POS/STR state, several configuration bits are not reset to their

default state. These bits are noted in the following register description.

2. Some register values at reset are determined by external strapping options.

The default s tate represents the mini mum functionali ty feature set requir ed to successful ly bring up

the system. Hence, it does not represent the optimal system conf iguration. It is the responsibility of

the system initialization software (usually BIOS) to properly determine the DRAM configurations,

operating parameters and optional system features that are applicable, and to program the

82443BX registers accordingly.

3.1 I/O Mapped Registers

The 82443BX contains three re

isters that reside in the CPU I/O address space − the

Confi

uration Address

(

CONFADD

)

ister, the Confi

uration Data

(

CONFDATA

)

ister, and the Power Mana

ement Contro l Re

ister. The Confi

uration Address

ister enables/disables the confi

uration space and determines what portion of

confi

uration space is visible throu

h the Confi

uration Data win dow.

3.1.1 CONFADD—Configuration Address Register

I/O Address: 0CF8h Accessed as a Dword

Default Value: 00000000h

Access: Read/Write

Size: 32 bits

CONFADD is a 32 bit register accessed only when referenced as a Dword. A Byte or Word

reference will "pass through" the Configuration Address Register onto the PCI b u s as an I/O c y cle.

The CONFADD register contains the Bus Number, Device Number, Function Number, and

82443BX Host Bridge Datasheet

3-3

3.1.2 CONFDATA—Configuration Data Register

I/O Address: 0CFCh

Default Value: 00000000h

Access: Read/Write

Size: 32 bits

CONFDATA is a 32 bit read/write window into configuration space. The portion of configuration

space that is referenced by CONFDATA is determined by the contents of CONFADD.

3.1.3 PM2_CTL—ACPI Power Control 2 Control Register

I/O Address: 0022h

Default Value: 00h

Access: Read/Write

Size: 8 bits

This register is used to disable both the PCI and AGP arbiters in the 82443BX to prevent any

external bus masters from acquiring the PCI or AGP bus. Any currently running PCI cycles will

terminate properly.

Bit Descriptions

31 Configuration Enable (CFGE). When this bit is set to 1 accesses to PCI configuration space are

enabled. If this bit is reset to 0 accesses to PCI configuration space are disabled.

30:24 Reserved.

23:16

Bus Number. When the Bus Number is programmed to 00h the target of the Configuration Cycle

is either the 82443BX or the PCI Bus that is directly connected to the 82443BX, depending on the

Device Number field. A type 0 Configuration Cycle is generated on PCI if the Bus Number is

programmed to 00h and the 82443BX is not the target. If the Bus Number is non-zero a type 1

configuration cycle is generated on PCI or AGP with the Bus Number mapped to AD[23:16] during

the address phase.

15:11

Device Number. This field selects one agent on the PCI bus selected b y the Bus Number. During

a Type 1 Configuration cycle this field is mapped to AD[15:11]. During a Type 0 Configuration

Cycle this field is decoded and one bit among AD[31:11] is driven to a 1. The 82443BX is always

Device Number 0 for the Host-to-PCI bridge entity and Device Number 1 f or the Host- AGP entity.

Therefore, the 82443BX internally references th e AD11 and AD12 pins as corresponding IDSELs

for the respective devices during PCI configuration cycles. NOTE: The AD11 and AD12 must not

be connected to any other PCI bus devi ce as IDSEL signals.

10:8

Function Number. This field is mapped to AD[10:8] during PCIx configuration cycles. This allows

the configuration registers of a particular function in a multi-function device to be accessed. The

82443BX only responds to configuration cycles with a function number of 000b; all other function

number values attempting access to the 82443BX (De v ice Number = 0 and 1, Bus Number = 0)

will generate a master abort.

7:2 Register Number. This field selects one register within a particular Bus, Device, and Function as

specified by the other fields in the Configuration Address Register. This field is mapped to AD[7:2]

during PCI configur ation cycles.

1:0 Reserved.

Bit Descriptions

31:0 Config uration Data Win dow (C DW). If bit 31 of CONFADD is 1 any I/O reference that falls i n the

CONFDATA I/O space will be mapped to configuration space using the contents of CONFADD.

3-4

82443BX Host Bridge Datasheet

Accesses to this register are controlled by the Power Management Control Register (Offset 7Ah).

When bit 6 of th e PMCR is set to ‘1 ’, the ACPI Re gister at I/O l ocation 0022h is enab led. W hen bi t

6 is set to ‘0’, I /O accesses to location 0022h are forward ed to PCI or AGP (if within prog rammable

IO range).

3.2 PCI Configuration Space Access

The 82443BX implementation manifests two PCI devices within a single physical component

body:

•Device 0 = Host-to-PCI Bridge = PCI bus #0 interface, Main Memory Controller, Graphics

Aperture controller, 82443BX specific AGP control registers.

•Device 1 = Host-to-AGP interface = “Virtual” PCI-to-PCI Bridge, including AGP address

space mapping, normal PCI interface, and associated AGP sideband signal control.

Correspon ding conf igu ration re gi sters for both de v ices are mapp ed as devices residing on PCI (b u s

0). Configuration register layout and functiona lity for the Device #0 should be inspected carefully,

as new features added to the 82443BX in itiated a reasonable level of change relative to other

proliferation’s of the Pent ium® Pro processor AGPsets (i.e. 440FX, 440LX). Configuration

registers of th e 82443BX De vice # 1 are based on the normal conf igu ration space template of a PCI-

to-PCI Bridge as described in the PCI to PCI Bridge Architecture Specification.

Figure 3-1shows the PCI bus hierarchy for the 82443BX). In the PCI bus hierarchy, the primary

PCI b u s is the hi gh est level bus in the hiera rchy and is P CI bus #0. The PCI-to-PCI bridge function

provides access to the AGP/PCI bus 0. This bus is below the primary bus in the PCI bus hierarchy

and is represented as PCI Bus #1.

Bit Description

7:1 Reserved

Primary PCI and A GP Arbiter Request Disable (ARB_DIS). When this bit is set to 1, the

82443BX will not respond to any PCI REQ# signals, AGP requests, or PHOLD # from PIIX4E going

activ e until this bit is set bac k to 0. Only External AGP and PCI requests are masked from the

arbiters. If the PIIX is in passiv e release mode , masking will not occur until an active release is seen

via PHLDA# assertion. This prevents possible deadlock.

ARB_DIS has no effect on AGP side band signals or AGP data transfer requests.

82443BX Host Bridge Datasheet

3-5

3.2.1 Configuration Space Mechanism Over view

The 82443BX supports two bus interfaces: PCI (referenced as Primary PCI) and AGP (referenced

as AGP). The AGP interface is treated as a second PCI bus from the configuration point of view.

The following sections describe the configuration space mapping mechanism associated with both

buses.

Note: The configuration space for device #1 is controlled by the AGP_DIS bit in the PMCR register.

When the A GP_DIS b it (PMCR[1]) is set to 0, the conf iguration space for de vice #1 is enabled, and

the registers for device #1 are accessible through the configuration mechanism defined below.

When the AGP_DIS bit (PMCR[1]) is set to 1, the configuration space for device #1 is disabled.

All configuration cycles (reads and writes) to device #1 of bus 0 will cause the master abort status

bit for device #0/ b us 0 to be set. Configuration read cycles will return data of all 1’ s. Conf iguration

write cycles will have no effect on the registers.

3.2.2 Routing the Configuration Accesses to PCI or AGP

Routing of configuration accesses to AGP is controlled via PCI-to-PCI bridge normal mechanism

using information contained within the PRIMARY BUS NUMBER, the SECONDARY BUS

NUMBER, and the SUBORDINATE BUS NUMBER registers of the Host-to-AGP internal

“virtual” PC I-to-PC I brid ge device. Detailed descripti on of th e mechanis m for trans lating C PU I/O

bus cycles to configuration cycles on one of the two buses is described below.

To distinguish between PCI configuration cycles targeting the two logical device register sets

supported in the 82 443BX, this document refers to the Ho st-to-PCI bridge PCI interf ace as PCI and

the Host- AGP PC I int erface as AGP.

Figure 3-1. 82443BX PCI Bus Hierarchy

CPU

Host-to-PCI Bridge

Virtual Host-to-PCI Bridge

AGP Device

PCI Bus #0

82443BX

Host Bridge

PCI Bus #1 – AGP

3-6

82443BX Host Bridge Datasheet

3.2.3 PCI Bus Configuration Mechanism Overview

The PCI Bus defines a slot based "configuration space" that allows each device to contain up to 8

functions with each function containing up to 256 8-bit configuration registers. The PCI

specification defines two bus cycles to access the PCI configuration space: Configuration Read

and Configuration Write. Memory and I/O spaces are supported directly by the CPU.

Configuration space is supported by a mapping mechanism implemented within the chip-set. The

PCI specification defines two mechanisms to access configuration space, Mechanism #1 and

Mechanism #2. The 82443BX supports only Mechanism #1.

The configuration access mechanism makes use of the CONFADD Register and CONFDATA

CONFADD that specifies the PCI bu s, the device on that bus, the function within the device, and a

specific configuration register of the device function being accessed. CONFADD[31] must be 1 to

enable a configuration cycle. CONFDATA then becomes a window into the four bytes of

config uration space specif ied b y the conten ts of CONFADD. Any read or write to CONFD ATA will

result in the Host Bridge translating CONFADD into a PCI configuration cycle.

3.2. 3.1 Type 0 Access

If the Bus Number field of CONFADD is 0, a Type 0 Configuration cycle is perfo rmed on PCI (i.e.

bus #0). CONFADD[10:2] is mapped directly to AD[10:2]. The Device Number field of

CONFADD is decoded onto AD[31:11]. The Host-to-PCI Bridge entity within the 82443BX is

accessed as Device #0 on the PCI bu s segmen t. The Host- /A GP Bridge entity within the 82443BX

is accessed as Device #1 on the PCI bus segment. To access Device #2, the 82443BX will assert

AD13, for Device #3 will assert AD14, and so forth up to Device #20 for which will assert AD31.

Only one AD line is asserted at a time. All device numbers higher than 20 cause a type 0

configuration access with no IDSEL asserted, which will result in a Master Abort.

3.2. 3.2 Type 1 Access

If the Bus Number f ield of CONFADD is non-zero, th en a Type 1 Con f igura tion c ycle is performed

on PCI bus (i.e. bus #0). CONFADD[23:2] is mapped directly to AD[23:2]. AD[1:0] are driven to

01 to indicate a Type 1 Configuration cycle. All other lines are driven to 0.

3.2.4 AGP Bus Configuration Mechanism Overview

This mechanism is compatible with PCI mechanism #1 supported for the PCI bus as defined abo v e.

The configuration mechanism is the same for both accessing AGP or PCI-only devices attached to

the AGP interface.

82443BX Host Bridge Datasheet

3-7

3.2.5 Mapping of Configuration Cyc les on AGP

From the AGPset conf ig uration perspecti v e, AGP is seen as another PCI b us interface residing on a

Secondary Bus side of the “virtual” PCI-to-PCI bridge referred to as the 82443BX Host- AGP

bridge. On the Primary b u s side, the “virtual” PCI-to-PCI bridge is attached to the B US #0 referred

to in this document as the PCI interface. The “virtual” PCI-to-PCI bridge entity is used to map

Type #1 PCI Bus Configuration c ycles on P CI onto Type #0 or Type #1 configuration c ycles on th e

AGP interface.

Type 1 configuration cycles on PCI that have a BUS-NUMBER that matches the SECONDARY-

BUS-NUMBER of the “virtual” PCI to PCI bridge will be translated into Type 0 configuration

cycles on the AGP interface. Type 1 conf iguration cy cles on PCI that hav e a BUS-NUMBER that is

behind the “virtual” P2P bridge will be translated into Type 1 configuration cycles on the AGP

interface.

Note: The PCI bus supports a total of 21 devices by mapping bits 15:11 of the CONFADD to the IDSEL

lines on AD[31:11]. For secondary PCI busses (including the AGP bus), only 16 devices are

supported by mapping bits 15:11 of the CONFADD to the IDSEL lines (AD[31:16]).

To prepare for mapping of the configuration cycles on AGP the initialization software will go

through the following sequence:

1. Scan all devices residing on the PCI bus (i.e., Bus #0) using Type 0 configuration accesses.

2. For every device residing at bus #0 which implements PCI-to-PCI bridge functionality, it will

configure the secondary bu s of the bridge with the appropriate number and scan further down

the hierarchy. This process will include the configuration of the “virtual” PCI-to-PCI Bridg e

within the 82443BX used to map the AGP address space in a software specific manner.

3-8

82443BX Host Bridge Datasheet

3.3 Host-to-PCI Bridge Registers (Device 0)

Table 3-1 shows the 82443BX configuration space for device #0.

Table 3-1. 82443BX Register Map — Device 0 (Sheet 1 of 2)

Address

Offset Register

Symbol Register Name Default Value Access

00–01h VID Vendor Identification 8086h RO

02–03h DID Device Identification 7190h/7192h RO

04–05h PCICMD PCI Command Register 0006h R/W

06–07h PCISTS PCI Status Register 0210h/0200h R O, R/WC

08 RID Revision Identification 00/01h/02h RO

09 — Reserved 00h —

0Ah SUBC Sub-Class Code 00h RO

0Bh BCC Base Class Code 06h RO

0Ch — Reserved 00h —

0Dh MLT Master Latency Timer 00h R/W

0Eh HDR Header Type 00h RO

10–13h APBASE Aperture Base Address 00000008h R/W,RO

14–2Bh — Reserved 00h —

2C–2Dh SVID Subsystem Vendor Identification 00h R/WO

2E–2Fh SID Subsystem Identification 00h R/WO

30–33h — Reserved 00h —

34h CAPPTR Capabilities Pointer A0h/00h RO

35–4Fh — Reserved 00h —

50–53h NBX CFG 440BX Configuration [0000h]:[00S0_00

00_000S_0S00b] R/W

54–56h — Reserved 00h —

57h DRAMC DRAM Control 00S0_0000b R/W

58h DRAMT DRAM Timing 03h R/W

59–5Fh PAM[6:0] Programmable Attribute Map (7 registers) 00h R/W

60–67h DRB[7:0] DRAM Row Boundary (8 registers) 01h R/W

68h FDHC Fixed DRAM Hole Control 00h R/W

69–6Eh MBSC Memory Buffer Strength Control 0000-0000-0000h R/W

6F–70h — Reserved 00h —

71h — Intel Reserved 1Fh —

72h SMRA M System Management RAM Control 02h R/W

73h ESMRAMC Extended System Management RAM Control. 38h R/W

74–75h RP S S DRAM Row Page Size 0000h R/W

76–77h SDRAMC SDRAM Control Register 0000h R/W

78–79h PGP O L Paging Policy Register 00h R/W

7Ah PMCR Power Management Control Register 0000_S0S0b R/W

7B–7Ch SC RR Suspend CBR Refresh Rate Register 0038h R/W

7D–7Fh — Reserved 00h —

82443BX Host Bridge Datasheet

3-9

NOTES:

1. The ‘S’ s

mbol represents the strappin

option.

2. Write operations must not be attempted to the Intel Reserved re

isters.

80–83h EAP Error Address Pointer Register 00000000h RO, R/WC

84–8Fh — Reserved 00h —

90h ERRCMD Error Command Register 80h R/W

91–92h ERRSTS Err or Status Register 0000h R/WC, RO

93h — Reserved 00h R/W

94–97h — Intel Reserved 00006104h —

98–99h — Intel Reserved 0500h —

9Ah — Intel Reserved 00h —

9B–9Fh — Reserved — —

A0–A3h ACAPID AGP Capability Identifier 00100002h

00000000h RO

A4–A7h AGPSTAT AGP Status Register 1F000203h RO

A8–ABh AGPCMD AGP Command Register 00000000h RW

AC–AFh — Reserved 00h —

B0–B3h AGPCTRL AGP Control Register) 00000000h R/W

B4h APSIZE Aperture Size Control Register 00h R/W

B5–B7h — Reserved 00h —

B8–BBh ATTBASE Aper ture Translation Table 00000000h R/W

BCh — Reserved — —

BDh — Reserved — —

BE–BFh — Reserved 00h —

C0–C3h — Intel Reserved 00000000h —

C4–C7h — Intel Reserved 00000000h —

C8h — Intel Reserved 18h —

C9h — Intel Reserved 0Ch —

CA–CCh MBFS Memory Buffer Frequency Select 000000h R/W

CD–CFh — Reserved 00h —

D0–D7h BSPAD BI OS Scratc h Pad 00...00h R/W

D8–DFh Intel Reserved 000....000h —

E0–E7h DWTC DRAM Write Thermal Throttling Control 000....000h R/W/L

E8–EFh DRTC DRAM Read Thermal Throttling Control 000....000h R/W/L

F0–F1h BUFFC Buffer Control Register 0000h R/W/L

F2–F7h — Intel Reserved 0000F800h —

F8–FBh — Intel Reserved 00000F20h —

FC–FFh — Intel Reserved 00000000h —

Table 3-1. 82443BX Register Map — Device 0 (Sheet 2 of 2)

Address

Offset Register

Symbol Register Name Default Value Access

3-10

82443BX Host Bridge Datasheet

3.3.1 VID—Vendor Identification Register (Device 0)

Address Offset: 00–01h

Default Value: 8086h

Attribute: Read Only

Size: 16 bits

The VID Register contains the vendor identification number. This 16-bit register combined with

the Device Iden tification Reg ister uniquely identify an y PCI device. Writes to this register ha ve no

eff ect.

3.3.2 DID—Device Identification Register (Device 0)

Address Offset: 02–03h

Default Value: 7190h/7192h

Attribute: Read Only

Size: 16 bits

This 16-bit register combined with the Vendor Identification register uniquely identifies any PCI

device. Writes to this register have no effect.

Bit Description

15:0 Vendor Identification Number. This is a 16-bit value assigned to Intel. Int el VID = 8086h.

Bit Description

15:0

Device Identification Number. This is a 16 bit value assigned to the 82443BX Host-to-PCI

Bridge Function #0.

7190h = When the AGP_DIS bit (PMCR[1]) is set to 0, the DID =7190h.

7192h = When the AGP_DIS bit is set to 1, the DID = 7192h.

82443BX Host Bridge Datasheet

3-11

3.3.3 PCICMD—PCI Command Register (Device 0)

Address Offset: 04–05h

Default: 0006h

Access: Read/Write

Size 16 bits

This 16-bit register provides basic cont rol over the 82443BX PCI interface ability to respond to

PCI cycles. The PCICMD Register enables and disables the SERR# signal, 82443BX response to

PCI special cycles, and enables and disables PCI bus master accesses to main memory.

Bit Descriptions

15:10 Reserved.

9Fast Bac k-to-Bac k. F ast bac k-to-back cycles to diff erent PCI targets are not implemented by the

82443BX.

0 = Hardwired to 0.

SERR# Enable (SERRE). Note that this bit only controls SERR# for the PCI bus. Device #1 has

its own SERRE bit to control error reporting f or t he bus conditi ons occurred on the AGP bus. Two

control bits are used in a logical OR manner to control SERR# pin driver.

1 = If this bit is set to a 1, the 82443BX’ s SERR# signal driver is enabled and SERR# is asserted

when an error condition occurs, and the corresponding bit is enabled in the ERRCMD

set and the 82443BX’s PCI parity error reporting is enabl ed by the PERRE bit located in this

target).

0 = SERR# is ne ver driven by the 82443BX.

7Address/Data Stepping. Not implemented (hardwired to 0).

P arity Err or Enable (PERRE). Note that the PERR# signal is not implemented by the 82443BX.

1 = Enable. Address and data parity errors are repor ted via SERR# mech anism (if enabled via

SERRE bit).

0 = Disable. Address and data parity errors are not reported via the 82443BX SERR# signal.

(NOTE: Other types of error conditions can be still signaled via SERR# mechanism.)

NOTE : The 82443BX PCI bus interface is still required to generate parity even if parity error

repor ting is disabled via this bit.

5 Reserved.

4Memory Write and Invalidate Enable. The 82443BX never uses this command.

0 = Hardwired to 0.

3Special Cycle Enable. The 82443BX ignores all special cycles generated on the PCI.

0 = Hardwired to 0.

2Bus Master Enable (BME). The 82443BX does not support disab ling of its b us master capability

on the PCI Bus.

1 = Hardwired to 1, per m itting the 82443BX to function as a PCI Bus master.

1Memory Access Enable (MAE). This bit enables/disables PCI master access to main memory

(DRAM). The 82443BX always allows PCI master access to main memory.

1 = Hardwired to 1.

0I/O Access Enable (IOAE). The 82443BX does not respond to PCI bus I/O cycles.

0 = Hardwired to 0.

3-12

82443BX Host Bridge Datasheet

3.3.4 PCISTS—PCI Status Register (Device 0)

Address Offset: 06–07h

Default Value: 0210h/0200h

Access: Read Only, Read/Write Clear

Size: 16 bits

PCISTS is a 16-bit status register that reports the occurrence of a PCI master abort and PCI target

abort on the PCI bus. PCISTS also indicates the DEVSEL# timing that has been set by the

82443BX hardware for target responses on the PCI bus. Bits [15:12] and bit 8 are read/write clear

and bits [10:9] are read only.

Bit Descriptions

Detected Parity Error (DPE). Note that the function of this bit is not affected by the PERRE bit.

PERR# is not implemented in the 82443BX.

1 = Indicates 82443BX’s detection of a parity error in the address or data phase of PCI bus

transactions.

0 = Software sets DPE to 0 by writing a 1 to this bit.

Signaled System Error (SSE).

1 = This bit is set to 1 when the 82443BX asserts SERR# for any enabled error condition under

device 0.

0 = Software sets SSE to 0 b y writing a 1 to this bit.

Received Master Abort Status (RMAS). Note that Master abort is the normal and expected

ter mination of PCI special cycles.

1 = When the 82443BX terminates a PCI bus transaction (82443BX is a PCI master) with an

unexpected master abort, this bit is set to 1.

0 = Software resets this bit to 0 by writing a 1 to it.

Received Target Abort Status (RTAS).

1 = When a 82443BX-initiat ed PCI transaction is terminated with a target abort, R TAS is set to 1.

The 82443BX also asserts SERR# if enabled in the ERRCMD register.

0 = Software resets RTAS to 0 by writing a 1 to it.

11 Signaled Target Abort Status (STAS). The 82443BX does not generate target abort.

0 = Hardwired to a 0

10:9

DEVSEL# Timing (DEVT). This 2-bit field indicates the timing of the DEVSEL# signal when the

82443BX responds as a target on PCI, and indicates the time when a valid DEVSEL# can be

sampled by the initiator of the PCI cycle.

01 = Medium (hardwired to 01)

8Data Parity Detected (DPD). 82443BX does not implement the PERR# pin. However, data parity

errors are still detected and reported on SERR# (if enabled by SERRE and PERRE).

0 = Hardwired to 0

7Fast Back- to-Back (FB2B). The 82443BX as a target does not support fast back-to-back

transactions on the PCI bus.

0 = Hardwired to 0

6:5 Reserved.

4Capability List (CLIST).

1 = When the AGP DIS bit (PMCR[1]) is set to 0, this bit is set to 1.

0 = When the AGP DIS bit (PMCR[1]) is set to 1, this bit is set 0.

3:0 Reserved.

82443BX Host Bridge Datasheet

3-13

3.3.5 RID—Revision Identification Register (Device 0)

Address Offset: 08h

Default Value: 02h

Access: Read Only

Size: 8 bits

This register contains the revision number of the 82443BX Function #0. These bits are read only

and writes to this register have no effect.

3.3.6 SUBC—Sub-Class Code Register (Device 0)

Address Offset: 0Ah

Default Value: 00h

Access: Read Only

Size: 8 bits

This register contains the Sub-Class Code for the 82443BX Function #0. This code is 00h

indicating a Host Bridge devi ce. The register is read only.

3.3.7 BCC—Base Class Code Register (Device 0)

Address Offset: 0Bh

Default Value: 06h

Access: Read Only

Size: 8 bits

This register contains the Base Class Code of the 82443BX Function #0. This code is 06h

indicating a Bridge device. This register is read only.

Bit Description

7:0 Revision Identification Number. This is an 8-bit value that indicates the revision identification

number for the 82443BX Function #0.

B-1 = 02h

Bit Description

7:0 Sub-Class Code (SUBC). This is an 8-bit value that indicates the category of Bridge into which

the 82443BX falls. The code is 00h indicating a Host Bridge.

Bit Description

7:0 Base Class Code (BASEC). This is an 8-bit value that indicates the Base Class Code for the

82443BX. This code has the val ue 06h, indicating a Bridge device.

3-14

82443BX Host Bridge Datasheet

3.3.8 MLT—Master Latenc y Timer Register (De vice 0)

Address Offset: 0Dh

Default Value: 00h

Access: Read/Write

Size: 8 bits

This register controls the amount of time that 82443BX can burst data on the PCI Bus as a PCI

master. The MLT[2:0] bits are reserved and assumed to be 0 when determining the Count Value.

3.3.9 HDR—Header Type Register (Device 0)

Offset: 0Eh

Default: 00h

Access: Read Only

Size: 8 bits

This register identifies the header layout of the configuration space.

3.3.10 APBASE—Aperture Base Configuration Register (Device 0)

Offset: 10–13h

Default: 00000008h

Access: Read/Write, Read Only

Size: 32 bits

The APB ASE is a normal PCI Base Address register that is used to request the base of the Graphics

Aperture. The normal PCI Configuration mechanism defines the base address configuration

hardwired to “0” or behave as hardwired to “0”). To allow for flexibility (of the aperture) an

additional register called APSIZE is used as a “back-end” register to control which bits of the

APBASE will behave as hardwired to “0”. This register will be programmed by the 82443BX

specific BIOS code that will run before any of the generic configuration software is run.

Note: Bit 9 of the NBXCFG register is used to prevent accesses to the aperture range before this register

is initialized by the configuration software and appropriate translation table structure has been

established in the main mem ory.

Bit Description

7:3

Master Latency Ti mer Count Value for PCI Bus Access. MLT is an 8-bit register that controls

the amount of time the 82443BX, as a PCI bus master, can burst data on the PCI Bus. The

default value of MLT is 00h and disables this f unction. For example, if the MLT is programmed to

18h, then the value is 24 PCI clocks.

2:0 Reserved.

Bit Descriptions

7:0 Header Type (HEADT). This read only field always returns 0 when read. Writes have no affect

on this field.

82443BX Host Bridge Datasheet

3-15

3.3.11 SVID—Subsystem Vendor Identification Register (Device 0)

Offset: 2C–2Dh

Default: 0000h

Access: Read/Write Once

Size: 16 bits

Bit Description

31:28 Upper Pr ogrammable Base Address bits (R/W). These bits are used to locate the range size

selected via lower bits 27:4.

Default = 0000b

27:22

Lower “Hardwired”/Programmable Base Address bits. These bits beha ve as a “hardwired” or

as a programmable depending on the contents of the APSIZE register as defined below:

27 26 25 24 23 22 Aper ture Siz e

r/w r/w r/w r/w r/w r/w 4 MB

r/w r/w r/w r/w r/w 0 8 MB

r/w r/w r/w r/w 0 0 16 MB

r/w r/w r/w 0 0 0 32 MB

r/w r/w 0 0 0 0 64 MB

r/w 0 0 0 0 0 128 MB

0 0 0 0 0 0 256 MB

Bits 27:22 are controlled by the bits 5:0 of the APSIZE register in the following manner:

If bit APSIZE[5]=0 then APBASE[27]=0 and if APSIZE[5]=1 then APBASE[27]=r/w (read/wr ite).

The same applies correspondingly to other bits.

Default for APSIZE[5:0]=000000b forces default APBASE[27:22] =000000b (i.e., all bits respond

as “hardwired” to 0). This provides a default to the maximum aperture size of 256 MB. The

82443BX specific BIOS is responsible for selecting smaller size (if required) before PCI

configuration software runs and establishes the system address map.

21:4 Hardwired to “0”. This forces minimum aperture size selected by this register to be 4MB.

3Prefetchable (RO). This bit is hardwired to “1” to identify the Gr aphics Aperture range as a

prefetchable ( i.e., the device returns all bytes on reads regardless of the byte enables), and the

82443BX may merge processor writes into this range without causing errors .

2:1 Type (RO). These bits determine addressing type and they are hardwired to “00” to indicate that

address range defined by the upper bits of this register can be located anywhere in the 32-bit

address space.

0Memory Space Indicator (RO). Hardwired to “0” to identify aper ture range as a memory range.

Bit Description

15:0 Subsystem Vendor ID (R/WO). This value is used to identify the vendor of the subsystem. The

default value is 00h. This field should be programmed during boot-up. After this field is written

once, it becomes read only.

3-16

82443BX Host Bridge Datasheet

3.3.12 SID—Subsystem Identification Register (Device 0)

Offset: 2E–2Fh

Default: 0000h

Access: Read/Write Once

Size: 16 bits

3.3.13 CAPPTR—Capabilities Pointer Register (Device 0)

Offset: 34h

Default: A0h/00h

Access: Read Only

Size: 8 bits

The CAPPTR pro v ides the o ffset that is the po inter to the loca tio n where the AGP normal re gisters

are located.

3.3.14 NBXCFG—NBX Configuration Register (Device 0)

Offset: 50–53h

Default: bits 31–16: 0000h

bits 15–0: 00S0-0000-000S-0S00b

Access: Read/Write, Read Onl

for strappin

options

Size: 32 bits

Bit Description

15:0 Subsystem ID (R/W O). This value is used to identify a particular subsystem. The default value is

00h. This field should be programmed during boot-up. After this field is written once, it becomes

read only.

Bit Description

7:0 Pointer to the start of AGP normal register block.

A0h = When the AGP_DIS bit (PMCR[1]) is set to 0, the value in this field is A0h.

00h = When the AGP_DIS bit (PMCR[1]) is set to 1, this field is set to 00h.

Bit Description

31:24

SDRAM Row Without ECC. Bit[n] of this 8 bit arra y corresponds to row[n] of the SDRAM array.

When reading a SDRAM row (DIMM) which is none-ECC, the 82 443BX drives the ECC data lines

during the first data transfer in a burst read.

0 = ECC components are populated in this row. The 82443BX will not drive the ECC signals.

1 = ECC components are not populated in this row. The 82443BX will drive the ECC lines in the

first read data transferred when this row is addressed.

23:19 Reserved.

Host Bus Fast Data Ready Enable (HBFDRE).

0 = Assertion of DRAM data on host bus occurs one clock after sampling snoop results. (default )

1 = Asser tion of DRAM data on host bus occurs on the same clock the snoop result is being

sampled. This mode is faster by one clock cycle.

82443BX Host Bridge Datasheet

3-17

ECC - EDO static Drive mode.

0 = Normal mode of operation (default).

1 = ECC signals are always driven. This mode is used in a mobile system. EDO components are

used, but ECC components are not populated in any of the DRAM rows.

IDSEL_REDIRECT. This is a programmable option to make the 82443BX com patible with 430TX

base design. For CPU initiated configuration cycles to PCI, De vice 1 which are targeted to the

82443BX’s host to AG P br idge:

0 = When set to ‘0’ (default), IDSEL1 (or AD12) is allocated to this bridge. The external AD12 is

never activated. CPU initiated configuration cycles to BUS0, DEVICE7 are targeted a PCI b us

device that its IDSEL input is connected to IDSEL7 (AD18).

1 = When set to ‘1’, IDSEL7 (or AD18) is allocated to this bridge. Since it is internal in the

82443BX, the external AD18 is never activated. CPU initiated configuration cycles to BUS0,

DEVICE7 are targeted a PCI bus device that its IDSEL input is connected to IDSEL1 (AD12).

In some 430TX based systems, this is connected to PIIX4E.

Note that CPU initiated configuration cycles to other PCI buses or other devices are normally

mapped and are not affected.

15 WSC# Handshake Disable. In the Uni-Processor mode, this bit should be set to ‘1’. In the Dual-

Processor mode where external IOAPIC is used, this bit should be set to ‘0’ (default). Setting this

bit to ‘0’, enables the WSC# handshake mechanism.

14 Intel Reserved.

13:12

Host/DRAM Frequency. These bits are used to determine the host and DRAM frequency. Bit 13

is set by an external strapping option at reset. These bits are also used to select the required

refresh rate . These bits apply to both SDRAM and EDO, with the exception that the setting ‘00’ for

100 MHz is illegal for an EDO system.

00 = 100 MHz

01 = Reserved

1 0 = 66 MHz

11 = Reserved

AGP to PCI Access Enable. When PHLDA# is active or there is an outstanding passive release

transaction pending: 1) this bit is set to 1 and the 82443BX allows AGP to PCI traffic, or 2) this bit

is set to 0 (default) and the 82443BX block s AGP to PCI traffic. The AGP to PCI traffic must not

target the ISA bus.

1 = Enable

0 =Disable

PCI Agent to Aperture Access Disable. This bit is used to prevent access to the aperture from

the PCI side.

1 = Disable

0 = Enable (default). If this bit is “0” (default) and bit 9 = 1, accesses to the aperture are enabled

for the PCI side.

Note: This bit is don’t care if bit 9 of this register = 0.

Aperture Access Global Enabl e. This bit is used to prev ent access to the aperture from any port

(CPU, PCI or AGP) before aperture range is established by the configuration software and

appropriate translation table in the main DRAM has been initialized. Default is “0”. It must be set

after system is fully configured for aperture accesses.

1 = Enable. Note that this bit globally controls accesses to the aperture. Once enabled, bit 10

provides the ne xt level of control f or accesses originated from the PCI side.

0 = Disable

8:7

DRAM Data Integrity Mode (DDIM) (R/W). These bits select one of 4 DRAM data integrity

modes.

00 = Non-ECC (Byte-Wise Writes supported) (Default)

01 = EC-only - Error Checking with No correction

10 = ECC Mode (Error Checking/Correction)

11 = ECC Mode with hardware scrubbing enabled

Bit Description

3-18

82443BX Host Bridge Datasheet

ECC Diagnostic Mode Enable (EDME) (R/W).

1 = Enable. When this bit is set to 1, the 82443BX will enter ECC Diagnostic test mode and the

82443BX forces the MECC[7:0] lines to 00h for all writes to memor y. During reads, the read

MECC[7:0] lines are compared against internally generated ECC. Recognized errors are

indicated via the ERRSTS register as in nor mal ECC operation.

0 = Normal operation mode (default).

MDA Present (MDAP).

This bit is used to indicate the presence of a secondary monochrome adapter on the PCI bus,

while the primar y graphics controller is on the AGP bus. This bit works in conjunction with the

VGA_EN bit (Register 3E, bit 3 of device 1) as follows:

VGA_EN MDAP Description

0 X All VGA cycles are sent to PCI. PCI master cycles to the VGA range

are not claimed by the 82443BX.

10 All VGA cycles are sen t to AGP. PCI master writes to VGA range are

claimed by the 82443BX and forwarded to the AGP bus.

11 All VGA cycles are sent to AGP, except f or cycles in the MDA range

(or the aliased ranges defined below). PCI master writes in the VGA

range (outside of the MD A range) are claimed by the 82443BX and

forwarded to AGP. PCI and AGP master read/writes to the MDA range

are ignored by the 82443BX.

The MD A r anges are a subset of the VGA ranges as follows:

Memor y : 0B0000h–0B7FFFh I/O: 3B4h, 3B5h, 3B8h, 3B9h, 3BAh, 3BFh

4 Reserved.

3USWC Write Post During I/O Bridge Access Enable (UWPIO) (R/W).

1 = Enable. Host USWC wr ites to PCI memory are posted.

0 = Disable . Posting of USWC is not allowed.

In-Or der Queue Depth (IOQD) (RO). This bit reflects the value sampled on A7# on the

deassertion of the CPURST#. It indicates the depth of the Pentium® Pro processor bus in-order

queue (i.e., level of Pentium Pro processor bus pipelining).

1 = In-order queue = maximum. If A7# is sampled “1” (i.e,. undriven on the Pe ntium Pro

processor bus), the depth of the Pentium Pro processor bus in-order queue is configured to

the maximum allowed by the Pentium Pro processor protocol (i.e., 8). However, the actual

maximum supported by the 82443BX is 4, and it is controlled by the 82443BX’s Pentium Pro

processor interface logic using the BNR# signaling mechanism.

0 = A7# is sampled asserted (i.e., “0”). The depth of the Pentium Pro processor bus in-order

queue is set to 1 (i.e., no pipelining support on the Pentium Pro processor b us).

NO TE: During reset, A7# can be driv en either b y the 82443BX or by an e xternal source as defined

by the strapping option on the MAB11# pin.

1:0 Reserved.

Bit Description

82443BX Host Bridge Datasheet

3-19

3.3.15 DRA MC— DRAM Control Register (Device 0)

Address Offset: 57h

Default Value: 00S0_0000b

Access: Read/Write

Size: 8 bits

Bit Description

7:6 Reserved.

Module Mode Con figurati on (MMCONFIG). This bit is set b y an e xternal strapping option. The

combination of this bit and the SDRAMPWR bit (SDRAMC register) determine the functioning of

the CKE signals as defined as follows:

SDRAMPWR MMC ONFIG CKE Operation

0 0 3 DIMM, CKE[5:0] driven, self-refresh entry staggered.

SDRAM dynamic power do wn available.

X 1 3 DIMM, CKE0 only, self-refresh entr y not staggered. SDRAM

dynamic power down unavailable.

1 0 4 DIMM, GCKE only, self-refresh entr y staggered. SDRAM

dynamic power down unavailab le.

NOTE: Under MMCONFIG mode, the AG P must be disabled.

4:3

DRAM Type (DT). This field indicates the DRAM type used to populate the entire array. When

set to 00, EDO timings are used f or all cycles to main memory. When set to 01, SDRAM timings

are used for all cycles to memory. When set to 10, timings for memory cycles accommodate

Registered SDRAMs. For registered SDRAM timings, all address and control lines to the

SDRAMs are assumed to be registered, while memory data and ECC bits are not registered.

EDO, SDRAM and Registered SDRAM cannot be mixed within a system.

00 = EDO

01 = SDRAM

10 = Registered SDRAM

11 = Reserved

NOTE: When PCIRST# asser tion occurs dur ing POS/STR, this bit is not reset to ‘0’.

2:0

DRAM Refresh Rate (DRR). The DRAM refresh rate is adjusted according to the frequency

selected by this field. Disabling the refresh cycle (000) results in the eventual loss of DRAM

data. Changing DRR value will reset the refresh request timer. This field is used in conjunction

with the SDRAM frequency bits in the NBXCFG register to determine the correct load value for

the refresh timer.

000 = Refresh Disabled

001 = 15.6 us

010 = 31.2 us

011 = 62.4 us

100 = 124.8 us

101 = 249.6 us

110 = Reserved

111 = Reserved

NOTE : When PCIRST# assertion occurs during POS/STR, this bit is not reset to ‘0’.

3-20

82443BX Host Bridge Datasheet

3.3.16 DRAMT—DRAM Timing Register (Device 0)

Address Offset: 58h

Default Value: 03h

Access: Read/Write

Size: 8 bits

This 8-bit register controls main memory DRAM timings. Refer to the DRAM section for details

regarding the DRAM timings programmed in this register.

3.3.17 PAM[6:0]—Programmable Attribute Map Registers

(Devi ce 0)

Address Of f set: 59h (PAM0) – 5Fh (PAM6)

Default Value: 00h

Attribute: Read/Write

The 82443BX al lo ws programmab le memory attr ib ut es on 13 Legacy memory seg ments of v ari ous

sizes in the 640 KB to 1 MB address range. Seven Programmable Attribute Map (PAM) Registers

are used to support these features. Cacheability of these areas is controlled v ia the MTRR re g isters

in the Pentium Pro processor. Two bits are used to specify memory attributes for each memory

segment. Th ese bits app ly to bo th h ost accesses and PCI initiator accesses to th e PAM areas. Th ese

attributes are:

RE Read Enable. When RE = 1, the host read accesses to the corresponding memory segment

are claimed by the 82443BX and directed to main memory. Conversely, when RE = 0, the

host read accesses are directed to PCI.

WE Write Enable. When WE = 1, the host write accesses to the corresponding memory

segment ar e claimed by the 8 2443BX and directed to main memory. Con versely, when WE

= 0, the host write accesses are directed to PCI.

The RE and WE attributes permit a memory segment to be Read Only, Write Only, Read/Write, or

disabled. For example, if a memory segment has RE = 1 and WE = 0, the segment is Read Only.

Each PAM Reg ister controls tw o regions, typically 16 KB in size. Each of these reg i ons has a 4- bit

field. The four bits that control each region have the same encoding and are defined in Table 3-2.

Bit Description

7:2 Reserved.

EDO RASx# Wait State (RWS). When RWS = 1, one additional wai t state is inserted bef ore RAS#

is asserted for row misses. This provides one clock of additional MAX[13:0] setup time to RASx#

assertion. This bit does not affect page misses since the MAX[13:0] lines are setup several clocks

in advance of RAS# assertion for page misses.

0 = 1 tASR

1 = 2 tASR

EDO CASx# Wait State (CWS). When CWS = 1, one additional wait state is inserted before the

assertion of the first CASx# for page hit cycles. This allows one additional clock of MA setup time

to the CASx# for the leadoff page hit cycle. Page mis s and row miss timings are not affected by

this bit.

0 = 1 Tasc

1 = 2 Tasc

82443BX Host Bridge Datasheet

3-21

As an example, consider a BIOS that is implemented on the expansion bus. During the

initialization process, the BIOS can be shadowed in main memory to increase the system

performance. When BIOS is shadowed in main memory, it should be copied to the same address

location. To shadow the BIOS, the attrib utes for that add ress range should b e set to write only. The

BIOS is shado wed by f irst doing a r ead of that address. This read is forw arded to the ex pansion b us.

The host then does a write of the same address, which is directed to main memory. After the BIOS

is shado wed, the attrib utes for that mem ory area are set to read only so that all writes are forw arded

to the expansion bus. Table 3-3 shows the PAM registers and the associated attribute bits:

NOTE:

1. The C0000h to CFFFFh segment can be used for SMM space if enabled by the SMRAM register

Table 3-2. Attribute Bit Assignment

Bits [7, 3]

Reserved B its [6, 2]

Reserved B its [5, 1]

WE Bits [4, 0]

RE Description

xx00

Disabled. DRAM is disabled and all accesses are

directed to PCI. The 82443BX does not respond as a

PCI target for any read or write access to this area.

xx01

Read Only. Reads are forwarded to DRAM and writes

are forwarded to PCI for termination. This write protects

the corresponding memor y segment. The 82443BX will

respond as a PCI target for read acce sses but not for

any write accesses.

xx10

Write O nly. Writes are forwarded to DRAM and reads

are forwarded to the PCI for termination. The 82443BX

will respond as a PCI target for write accesses but not

for any read accesses.

xx11

Read/Write. This is the normal operating mode of main

memory. Both read and write cycles from the host are

claimed by the 82443BX and forwarded to DRAM. The

82443BX will respond as a PCI target for both read and

write accesses.

Table 3-3. PAM Registers and Associated Memory Segments

PAM Reg Attribute Bits Memory Segment Comments Offset

PAM0[3:0] Reserved 59h

PAM0[7:4] R R WE RE 0F0000h – 0FFFFFh BIOS Area 59h

PAM1[3:0] R R W E RE 0C0000h – 0C3FFFh ISA Add-on BIOS¹ 5Ah

PAM1[7:4] R R W E RE 0C4000h – 0C7FFFh ISA Add-on BIOS¹ 5Ah

PAM2[3:0] R R WE RE 0C8000h – 0CBFFFh ISA Add-on BIOS¹ 5Bh

PAM2[7:4] R R WE RE 0CC000h – 0CFFFFh ISA Add-on BIOS¹ 5Bh

PAM3[3:0] R R W E RE 0D0000h – 0D3FFFh ISA Add-on BIOS 5Ch

PAM3[7:4] R R W E RE 0D4000h – 0D7FFFh ISA Add-on BIOS 5Ch

PAM4[3:0] R R W E RE 0D8000h – 0DBFFFh ISA Add-on BIOS 5Dh

PAM4[7:4] R R WE RE 0DC000h – 0DFFFFh ISA Add-on BIOS 5Dh

PAM5[3:0] R R WE RE 0E0000h – 0E3FFFh BIOS Extension 5Eh

PAM5[7:4] R R WE RE 0E4000h – 0E7FFFh BIOS Extension 5Eh

PAM6[3:0] R R WE RE 0E8000h – 0EBFFFh BIOS Extension 5Fh

PAM6[7:4] R R WE RE 0EC000h – 0EFFFFh BIOS Extension 5Fh

3-22

82443BX Host Bridge Datasheet

DOS Application Area (00000h–9FFFh)

The DOS area is 640 KB and it is fur ther di vid ed in to tw o pa rts. Th e 512 KB area at 0 to 7 FFFFh i s

always mapped to the main memory controlled by the 82443BX, while the 128 KB address range

from 080000 to 09FFFFh can be mapped to PCI or to main DRAM. By default this range is

mapped to main memory and can be declared as a main memory hole (accesses forwarded to PCI)

via 82443BX’s FDHC configuration register.

Video Buffer Area (A0000h–BFFFFh)

This 128 KB area is not controlled by attribute bits. The host-initiated cycles in this region are

always forwarded to either PCI or AGP unless this range is accessed in SMM mode. Routin g of

accesses is controlled by the Legacy VG A control mechanism of the “virtual” PCI-to-PCI bridge

device embedded within the 82443BX.

This area can be programmed as SMM area via the SMRAM register. When used as a SMM space

this range can not be accessed from PCI or AGP.

Expansion Area (C0000h–DFFFFh)

This 128 KB area is divided into eight 16 KB segments which can be assigned with different

attributes via PAM control register as defined by Table 3-3.

Extended System BIOS Area (E0000h–EFFFFh)

This 64 KB area is divided into four 16 KB segments which can be assigned with different

attributes via PAM control register as defined by the Table 3-3.

System BIOS Area (F0000h–FFFFFh)

This area is a single 64 KB segment which can be assigned with different attributes via PAM

control register as defined by the Table 3-3.

3.3.18 DRB[0:7]—DRAM Row Boundary Registers (De vice 0)

Address Offset: 60h (DRB0) – 67h (DRB7)

Default Value: 01h

Access: Read/Write

Size: 8 bits/register

The 82443BX supports 8 physical rows of DRAM. The width of a row is 64 bits. The DRAM Row

Boundary Re g isters def i n e up per and lo wer ad dresses for each DR AM row. Contents of these 8-bit

registers represent the boundary addresses in 8 MB granularity. For ex ample, a value of 01h

indicates 8 MB.

60h DRB0 = Total memory in row0 (in 8 MB)

61h DRB1 = Total memory in row0 + row1 (in 8 MB)

62h DRB2 = Total memory in row0 + row1 + row2 (in 8 MB)

63h DRB3 = Total memory in row0 + row1 + row2 + row3 (in 8 MB)

64h DRB4 = Total memory in row0 + row1 + row2 + row3 + row4 (in 8 MB)

65h DRB5 = Total memory in row0 + row1 + row2 + row3 + row4 + row5 (in 8 MB)

66h DRB6 = Total memory in row0 + row1 + row2 + row3 + row4 + row5 + row6 (in 8 MB)

67h DRB7 = Total memory in row0 + row1 + row2 + row3 + row4 + row5 + row6 + row7

(in 8 MB)

82443BX Host Bridge Datasheet

3-23

The DRAM array can be configured with single or double-sided DIMMs using 2MX8, 4Mx16, or

8Mx8 parts. The array also supports x4 width DRAM components on registered DIMMs. Each

be asserted (e.g., if the first DRAM row is minus 8 MB, then accesses within the 0 to 8 MByte

range will cause CSx0#/RASx0# to be asserted). The DRAM Row Boundary (D RB) Registers are

programmed with an 8-bit upper address limit value. This upper address limit is comp ared to bits

[30:23] of the requested address, for each row, to determine if DRAM is being targeted.

Note: DRAM is selected only if address[31:30] are zero.

Row Boundary Address

These 8 bit v alues represent the upper address limits of the eight rows (i.e., this row minus previous

row = row size). Unpopulated rows have a value equal to the previous row (row size = 0). DRB7

reflects the maximum amount of DRAM in the system. The top of memory is determined by the

value written in to DRB7.

Note: The 82443BX supports a maximum of 1 GB of DRAM using registered SDRAM DIMMs. (an

example of this configuration is 4 double-sided registered DIMMs using 16Mx4 parts).

As an example of a general purpose configuration where eight physical rows are configured for

either single-sided or double-sided DIMMs, the memory array would be configured like the one

shown in Figure 3-2. In this configuration, the 82443BX drives eight CS# signals directly to the

DIMM rows. If single-sided DIMMs are populated, the even CS# signals are used and the odd

CS#s are not connected. If doub le-sided DIMMs are used, all four CS # signals are used per DIMM.

Bit Description

7:0 Row Boundary Address. This 8-bit value is compared against address lines A[30:23] to

determine the upper address limit of a par ticular row (i.e., DRB minus previous DRB = row size).

NOTE : When PCIRST# assertion occurs during POS/STR, these bits are not reset to ‘01h’.

Figure 3-2. SDRAM DIMMs and Corresponding DRB Registers

CSA7#/CSB7# DIMM3 – Back

DIMM3 – Fr ont

DIMM2 – Back

DIMM2 – Fr ont

DIMM1 – Back

DIMM1 – Fr ont

DIMM0 – Back

DIMM0 – Fr ont

CSA6#/CSB6#

CSA5#/CSB5#

CSA4#/CSB4#

CSA3#/CSB3#

CSA2#/CSB2#

CSA1#/CSB1#

CSA0#/CSB0#

DRB7

DRB6

DRB5

DRB4

DRB3

DRB2

DRB1

DRB0

3-24

82443BX Host Bridge Datasheet

The following 2 examples describe how the DRB Registers are programmed for cases of single-

sided and double-sided DIMMs on a motherboard.

Exam ple #1 Single-sided DIMMs

Assume a total of 16 MB of DRAM are required using single-sided 1MB x 64 DIMMs. In this

configuration, two DIMMs are required.

DRB0 = 01h populated (1 DIMM, 8 Mbyte this row)

DRB1 = 01h empty row

DRB2 = 02h populated (1 DIMM, 8 Mbyte this row)

DRB3 = 02h empty row

DRB4 = 02h empty row

DRB5 = 02h empty row

DRB6 = 02h empty row

DRB7 = 02h empty row

Exam ple #2 Mixed Single-/Double-sided DIMMs

As another e xample, consider a system that is initially shipped with 8 MB of memory using a 1M x

64 DIMM and that rest of the memory array should be upgradable up to a maximum supported

memory of 200 MB. Thi s can be hand led b y furt her popu latin g the array wi th one 16M x 64 sing le-

sided DIMM (one row) and one 8M x 64 double-sided DIMM (two rows), yielding a total of 200

MB of DRAM. The DRB Registers are programmed as follows:

DRB0 = 01h populated with 8 MB, 1MB x 64 single-sided DIMM

DRB1 = 01h emp t y row

DRB2 = 05h populated with 32 MB, 1/2 of 8M x 64 DIMM

DRB3 = 09h populated with 32 MB, the other 1/2 of 8M x 64 DIMM

DRB4 = 19h populated with 128 MB, 16M x 64 single-sided DIMM

DRB5 = 19h emp t y row

DRB6 = 19h emp t y row

DRB7 = 19h emp t y row

3.3.19 FDHC—Fixed DRAM Hole Control Register (Device 0)

Address Offset: 68h

Default Value: 00h

Access: Read/Write

Size: 8 bits

This 8-bit regi ster controls 2 fixed DRAM holes: 512 KB – 640 K B and 15 MB –16 MB.

Bit Description

7:6

Hole Enable (HEN). This field enables a memory hole in DRAM space. Host cycles matching an

enabled hole are passed on to PCI. PCI cycles matching an enabled hole will be ignored by the

82443BX (no DEVSEL#). NOTE: A selected hole is not remapped.

00 = None

01 = 512 KB–640 KB (128 KB bytes)

10 = 15 MB – 16 MB (1 MB byte)

11 = Reserved

5:0 Reserved.

82443BX Host Bridge Datasheet

3-25

3.3.20 MBSC—Memory Buffer Strength Control Register

(Device 0)

Address Offset: 69–6Eh

Default Value: 000000000000h

Access: Read/Write

Size: 48 bits

This register programs the various DRAM interface signal buffer strengths, based on non-mixed

memory configurations of DRAM type (EDO or SDRAM), DRAM density (x8, x16, or x32),

DRAM technology (16MB or 64 MB), and rows populated. Note that x4 DRAM may only be

supported when used on registered DIMMs.

Note: The choice of 100 MHz o r 6 6 MHz buffer is in depen dent of bus fr equen c y. It is possible to select a

100 MHz memory buffer even though the bus frequency is 66 MHz (and vice versa).

Bit Description

47:40 Reserved

39:38

MAA[13:0], WEA#, SRASA#, SCASA# Buffer Strengths. This field sets the b uff er strength f or

the MAA[13:0], WEA#, SRASA#, SCASA# pins.

00 = 1x (66 MHz & 100 MHz)

01 = Reserved (Invalid setting)

10 = 2x (66 MHz & 100 MHz)

11 = 3x (66 MHz & 100 MHz)

37:36

MAB[12:11, 9:0]# & MAB[13,10], WEB#, SRASB#, SCASB# Buffer Strengths. This field sets

the buffer strength for MAB[12:11, 9:0]# & MAB[13,10], WEB#, SRASB#, SCASB# pins. Note

that the address’s MAB# are inverted copies of MAA, with the exception of MAB[13,10].

00 = 1x (66 MHz & 100 MHz)

01 = Reserved (Invalid setting)

10 = 2x (66 MHz & 100 MHz)

11 = 3x (66 MHz & 100 MHz)

35:34

MD [63:0] Buffer Strength Control 2.

4 DIMM FET Configuration: This field sets the buffer strength for the MD[63:0] path that is

connected to DIMM2 and DIMM3. The buffer strength is progr ammable based on the SDRAM

load in detected in DIMM slots 2&3. This path is enabled when FENA is asserted (High) by the

82443BX.

3 DIMM & 4 DIMM non-FET Configuration: This field should be programmed to the same

v alue as MD[63:0] Buffer Strength Control 1. This buffer strength is programmable based upon

the SDRAM load detected in all DIMM connectors.

00 = 1x (66 MHz & 100 MHz)

01 = Reserved (Invalid setting)

10 = 2x (66 MHz & 100 MHz)

11 = 3x (100 MHz only)

33:32

MD [63:0] Buffer Strength Control 1.

4 DIMM FET Configuration: This field sets the buffer strength for the MD[63:0] path that is

connected to DIMM0 and DIMM1. The buffer strength is progr ammable based upon the

SDRAM load in detected in DIMM slots 0&1. This path is enabled when FENA is asserted

(Low) by the 82443BX.

3 DIMM & 4 DIMM non-FE T Configuratio ns: The buff er strength is progr ammable based upon

the SDRAM load detected in all DIMM connectors.

00 = 1x (66 MHz & 100 MHz)

01 = Reserved (Invalid setting)

10 = 2x (66 MHz & 100 MHz)

11 = 3x (100 MHz only)

3-26

82443BX Host Bridge Datasheet

31:30

MECC [7:0] Buffer Strength Control 2.

4 DIMM FET Configuration: This field sets the buffer strength f or the MECC[7:0] path that is

connected to DIMM2 and DIMM3 The buf f er strength is prog rammab le based upon the SDRAM

ECC load detected in DIMM slots 2&3. This path is enabled when FENA is deasserted (High)

by the 82443BX.

3 DIMM & 4 DIMM non-FET Configurations: This field should be programmed to the same

value as MECC[7:0] Buffer Strength Control 1. This buffer strength is programmable based

upon the SDRAM load detected in all DIMM connectors.

00 = 1x (66 MHz & 100 MHz)

01 = Reserved (Invalid setting)

10 = 2x (66 MHz & 100 MHz)

11 = 3x (100 MHz only)

29:28

MECC [7:0] Buffer Strength Control 1.

4 DIMM FET Configuration: This field sets the buffer strength f or the MECC[7:0] path that is

connected to DIMM0 and DIMM1. The buffer strength is programmable based upon the

SDRAM ECC load detected in DIMM slots 0&1. This path is enab led when FENA is deasserted

(High) by the 82443BX.

3 DIMM & 4 DIMM non-FET Configuration: The b uffer strength is programmable based upon

the SDRAM ECC load detected in all DIMM slots .

00 = 1x (66 MHz & 100 MHz)

01 = Reserved (Invalid setting)

10 = 2x (66 MHz & 100 MHz)

11 = 3x (100 MHz only)

27:26

CSB7#/CKE5 Buffer Strength. This field sets the buffer strength for CSB7#/CKE5 pins.

00 = 1x (66 MHz & 100 MHz)

01 = Reserved (Invalid setting)

10 = 2x (66 MHz & 100 MHz)

11 = 3x (66 MHz & 100 MHz)

25:24

CSA7#/CKE3 Buffer Strength. This field sets the buffer strength for CSA7#/CKE3 pins.

00 = 1x (66 MHz & 100 MHz)

01 = Reserved (Invalid setting)

10 = 2x (66 MHz & 100 MHz)

11 = 3x (66 MHz & 100 MHz)

23:22

CSB6#/CKE4 Buffer Strength. This field sets the buffer strength for CSB6#/CKE4 pins.

00 = 1x (66 MHz & 100 MHz)

01 = Reserved (Invalid setting)

10 = 2x (66 MHz & 100 MHz)

11 = 3x (66 MHz & 100 MHz)

21:20

CSA6#/CKE2 Buffer Strength. This field sets the buffer strength f or CSA6#/CKE2pins.

00 = 1x (66 MHz & 100 MHz)

01 = Reserved (Invalid setting)

10 = 2x (66 MHz & 100 MHz)

11 = 3x (66 MHz & 100 MHz)

CSA5#/RASA5#, CSB5#/RASB5# Buffer Strength. This field sets the buffer strength for the

CSA5#/RASA5#, CSB5#/RASB5# pins.

0 = 1x (66 MHz & 100 MHz)

1 = 2x (66 MHz & 100 MHz)

CSA4#/RASA4#, CSB4#/RASB4# Buffer Strength. This field sets the buffer strength for the

CSA4#/RASA4#, CSB4#/RASB4# pins.

0 = 1x (66 MHz & 100 MHz)

1 = 2x (66 MHz & 100 MHz)

CSA3#/RASA3#, CSB3#/RASB3# Buffer Strength. This field sets the buffer strength for the

CSA3#/RASA3#, CSB3#/RASB3# pins.

0 = 1x (66 MHz & 100 MHz)

1 = 2x (66 MHz & 100 MHz)

Bit Description

82443BX Host Bridge Datasheet

3-27

CSA2#/RASA2#, CSB2#/RASB2# Buffer Strength. This field sets the buf fer strength for the

CSA2#/RASA2#, CSB2#/RASB 2# pins.

0 = 1x (66 MHz & 100 MHz)

1 = 2x (66 MHz & 100 MHz)

CSA1#/RASA1#, CSB1#/RASB1# Buffer Strength. This field sets the buf fer strength for the

CSA1#/RASA1#, CSB1#/RASB 1# pins.

0 = 1x (66 MHz & 100 MHz)

1 = 2x (66 MHz & 100 MHz)

CSA0#/RASA0#, CSB0#/RASB0# Buffer Strength. This field sets the buf fer strength for the

CSA0#/RASA0#, CSB0#/RASB 0# pins.

0 = 1x (66 MHz & 100 MHz)

1 = 2x (66 MHz & 100 MHz)

13:12

DQMA5/CASA5# Buffer Strength. This field sets the buffer strength for the DQMA5/CASA5#

pins.

00 = 1x (66 MHz & 100 MHz)

01 = Reserved (Invalid setting)

10 = 2x (66 MHz & 100 MHz)

11 = 3x (66 MHz only)

11:10

DQMA1/CASA1# Buffer Strength. This field sets the buffer strength for the DQMA1/CASA1#

pin.

00 = 1x (66 MHz & 100 MHz)

01 = Reserved (Invalid setting)

10 = 2x (66 MHz & 100 MHz)

11 = 3x (66 MHz & 100 MHz)

9:8

DQMB5/CASB5# Buffer Strength. This field sets the buffer strength for the DQMB5/CASB5#

pin.

00 = 1x (66 MHz & 100 MHz)

01 = Reserved (Invalid setting)

10 = 2x (66 MHz & 100 MHz)

11 = 3x (66 MHz only)

7:6

DQMB1/CASB1# Buffer Strength. This field sets the buffer strength for the DQMB1/CASB1#

pin.

00 = 1x (66 MHz & 100 MHz)

01 = Reserved (Invalid setting)

10 = 2x (66 MHz & 100 MHz)

11 = 3x (66 MHz only)

5:4

DQMA[7:6,4:2,0]/CASA[7:6,4:2,0]# Buffer Strength. This field sets the buffer strength for the

DQMA[7:6]/CASA[7:6]#, DQMA[4:2]/CASA[4:2]#, and the DQMA[0]/CASA[0]# pins.

00 = 1x (66 MHz & 100 MHz)

01 = Reserved (Invalid setting)

10 = 2x (66 MHz & 100 MHz)

11 = 3x (66 MHz & 100 MHz)

3:2

CKE1/GCKE Buffer Strength. This field sets the buffer strength for the CKE1 pin.

00 = 1x (66 MHz & 100 MHz)

01 = Reserved (Invalid setting)

10 = 2x (66 MHz & 100 MHz)

11 = 3x (66 MHz & 100 MHz)

1:0

CKE0/FENA Buffer Strength. This field sets the buffer strength for the CKE0/FE NA pin.

00 = 1x (66 MHz & 100 MHz)

01 = Reserved (Invalid setting)

10 = 2x (66 MHz & 100 MHz)

11 = 3x (66 MHz & 100 MHz)

Bit Description

3-28

82443BX Host Bridge Datasheet

3.3.21 SMRAM—System Management RAM Control Register

(Device 0)

Address Offset: 72h

Default Value: 02h

Access: Read/Write

Size: 8 bits

The SMRAMC register controls how accesses to Compatible and Extended SMRAM spaces are

treated. The Open, Close, and Lock bits function only when G_SMRAME bit is set to a 1. Also, the

OPEN bit must b e res e t before the LOCK bit is set.

Bit Description

7 Reserved

SMM Space Open (D_OPEN). When D_OPEN=1 and D_LCK=0, the SMM space DRAM is made

visible even when SMM decode is not active . This is intended to help BIOS initialize SMM space.

Software should ensure that D_OPEN=1 and D_CLS=1 are not set at the same time. When

D_LCK is set to a 1, D_OPEN is reset to 0 and becomes read only.

SMM Space Closed (D_CLS). When D_CLS = 1 SMM spac e DRAM is not accessible to data

references, even if SMM decode is active. Code references may still access SMM space DRAM.

This will allo w SMM software to reference "through" SMM space to update the displa y even when

SMM is mapped over the V GA range . Softw are should ensure that D_OPEN=1 and D_CLS=1 are

not set at the same time.

SMM Space Locked (D_LCK). When D_LCK is set to 1 then D_OPEN is reset to 0 and D_LCK,

D_OPEN, H_SMRAM_EN, TSEG_SZ, TSEG_EN and DRB7 become read only. D_LCK can be

set to 1 via a normal configuration space write but can only be cleared by a power-on reset. The

combination of D_LCK and D_OPEN provide convenience with security. The BIOS can use the

D_OPEN function to initialize SMM space and then use D_LCK to "lock down" SMM space in the

future so that no application software (or BIOS itself) can violate the integrity of SMM space, even

if the program has knowledge of the D_OPEN function.

Global SMRAM Enable (G_SMRAME). If G_SMRAME is set to a 1 and H_SMRAM_EN is set to

0, then Compatible SMRAM functions are enabled, providing 128 KB of DRAM accessible at the

A0000h address while in SMM (ADS# with SMM decode). To enable Extended SMRAM function

this bit has be set to 1. Refer to the section on SMM for more details .

Once D_LCK is set, this bit becomes read only.

2:0

Compatible SMM Space Base Segment (C_B ASE_SEG) (RO). This field programs the location

of SMM space. "SMM DRAM" is not remapped. It is simply "made visible" if the conditions are

right to access SMM space, otherwise the access is forwarded to PCI.

010 = Hardwired to 010 to indicate that the 82443BX supports the SMM space at

A0000h–BFFFFh.

82443BX Host Bridge Datasheet

3-29

3.3.22 ESMRAMC—Extended System Management RAM Control

Address Offset: 73h

Default Value: 38h

Access: Read/Write

Size: 8 bits

The Extended SMRAM register controls the configuration of Extended SMRAM space. The

Extended SMRAM (E_SMRAM) memory provides a write-back cacheable SMRAM memory

space that is above 1 Mbyte.

Bit Descri

tion

H_SMRAM_EN (H_SMRAME). Controls the SMM memory space location (i.e above 1 Mbyte or

below 1 Mbyte).

1 = When G_SMRAME is 1 and H SMRAME is set to 1, the High SMRAM memory space is

enabled, the Compatible SMRAM memory is disabled, and accesses in the 0A0000h to

0FFFFFh range are forwarded to PCI, while SMRAM accesses from 100A0000h to

100FFFFFh are remapped to DRAM address A0000h to FFFFFh

0 = When G SMRAME is set to a 1 and H SMRAM EN is set to 0, then the Compatible SMRAM

space is enabled.

Once D_LCK is set, this bit becomes read only.

E_SMRAM_ERR (E _SM ERR).

1 = This bit is set when CPU accesses the defined memor y ranges in Extended SMRAM (High

Memor y and T-segment) while not in SMM space and with the D-OPEN bit = 0.

0 = It is software’s responsibility to clear this bit. The software must write a 1 to this bit to clear it.

5SMRAM_Cache (SM_CACHE). This bit is forced to ‘1’ b y 82443BX.

4SMRAM_L1_EN (SM_L1). This bit is for ced to ‘1’ by 82443BX.

3SMRAM_L2_EN (SM_L2). This bit is for ced to ‘1’ by 82443BX.

2:1

TSEG_SZ[1:0] (T_SZ). Selects the size of the TSEG memory block, if enabled. This memory is

taken from the top of DRAM space (i.e., TOM - TSEG_SZ), which is no longer claimed by the

memory controller (all accesses to this space are sent to the PCI bus if TSEG_EN is set). The

ph ysical address for the e xtended SMRAM memory appears is from (256M + T OM - TSEG_SZ) to

(256M + T OM). This address is remapped to DRAM address (TOM - TSEG_SZ) to T OM. This field

decodes as follows:

00 = (TOM–128KB) to TO M

01 = (TOM–256KB) to TO M

10 = (TOM–512KB) to TOM

11 = (TOM–1MB) to TOM

Once D_LCK is set, this bit becomes read only.

TSEG_EN (T_EN). Enabling of SMRAM memor y (TSEG, 128 KB, 256 KB, 512 KB or 1 MB of

additional SMRAM memory) for Extended SMRAM space only. When

G_SMRAME =1 and TSEG_EN = 1, the TSEG is enabled to appear in the appropriate physical

address space. Once D_LCK is set, this bit becomes read only.

3-30

82443BX Host Bridge Datasheet

3.3.23 RPS—SDRAM Row Page Size Register (Devi ce 0)

Address Offset: 74h–75h

Default Value: 0000h

Access: Read/Write

Size: 16 bits

This register sets the row page size for SDRAM only. For EDO memory, the page size is fixed at

2 KB.

3.3.24 SDRAMC—SDRAM Control Register (Device 0)

Address Offset: 76h–77h

Default Value: 00h

Access: Read/Write

Size: 16 bits

Bit Description

15:0

Pa ge Size (PS). Each pair of bits in thi s register indicate t he page siz e used for one row of DRAM.

The encoding of the two bit fields.

Bits[1:0] Page Size

00 2 KB

01 4 KB

10 8 KB

11 Reserved

RPS bits Corresponding DRB register

1:0 DRB[0], row 0

3:2 DRB[1], row 1

5:4 DRB[2], row 2

7:6 DRB[3], row 3

9:8 DRB[4], row 4

11:10 DRB[5], row 5

13:12 DRB[6], row 6

15:14 DRB[7], row 7

Bit Description

15:10 Reserved

9:8 Idle/Pipeline DRAM Leadoff Timing (IPDLT). Adds a clock delay to the lead-off clock count

when bits 9:8 are set to 01. All other settings are illegal.

82443BX Host Bridge Datasheet

3-31

7:5

SDRAM Mode Select (SMS). These bits allow the 82443BX to drive various commands to the

SDRAMs. These special modes are intended for initialization at power up.

SMS Mode

000 Normal SDRAM Operation. (def ault)

001 NOP Command Enable. In this mode all CPU cycles to SDRAM result in NOP

Command on the SDRAM interface.

010 All Banks Precharge Enable. In this mode all CPU cycles to SDRAM result in an All

Banks Precharge Command on the SDRAM interface.

011 Mode Register Set Enable. In this mode all CPU cycles to SDRAM result in a mode

MAx[13:0] lines. MAx[2:0] must always be driven to 010 for burst of 4 mode. MA3 must

be driven to 1 for interlea ve wrap type. MAx4 needs to be driven to the value

programmed in the CAS# Latency bit. MAx[6:5] should alwa ys be driven to 01.

MAx[12:7] must be driven to 000000. BIOS must calculate and drive the correct host

address for each row of memory such that the correct command is driven on the

MAx[12:0] lines.

100 CBR Enable. In this mode all CPU cycles to SDRAM result in a CBR cycle on the

SDRAM interface.

101 Reserved.

110 Reserved.

111 Reserved.

Note: BIOS must take into consideration MAB inversion when programming for 3 and 4 DIMM.

SDRAMPWR. The SDRAMP WR bit controls how the CKE signals are driven for different DRAM

configurations. For a 3 DIMM configuration, SDRAMPWR should be set to ‘0’. For a 4 DIMM

configuration, SDRAMPWR should be set to ‘1’. In this case the 82443BX drives a single CKE

signal (GCKE). The combinat ion of SDRAMPWR and MMCONFIG (DRAMC register) determine

the functioning of the CKE signals. Refer to the DRAMC register (Section 3.3.15, “DRAMC—

DRAM Control Register (Device 0)” on page 3-19) for more details.

Note: When PCIRST# assertion occurs during POS/STR, these bits are not reset to 0.

Leadoff Command Timing (LCT). These bits control when the SDRAM command pins

(SRASx#, SCA Sx# and WEx#) and CSx # are conside red valid on leadoffs for CPU cycles.

0 = 4 CS# Clock

1 = 3 CS# Clock

The LCT Bit should be initialized by BIOS as recommended below:

• Desktop platform s r unning at 100 MHz should leave the LCT bit set to its default value of 0.

• Desktop platform s r unning at 66 MHz should leave the LCT bit set to its default value of 0, if

load on either MAA or MAB signals is > 9. Otherwise, set the LCT bit to 1, if load on both

MAA and MAB is ≤ 9.

• Mobile platf orms will be run at 66MHz and should set the LCT bit to 1.

CAS# Latency (CL). This bit controls the number of CLKs between when a read command is

sampled by the SDRAMs and when the 82443BX samples read data from the SDRAMs. If a

giv en row is populated with a registered SDRAM DIMM, an extra clock is inserted between the

read command the when the 82443BX samples read data. For a registered DIMM with CL=2,

this bit should be set to 1.

0 = 3 DCLK CAS# latency.

1 = 2 DCLK CAS# latency.

SDRAM RAS# to CAS# Delay (SRCD). This bit controls the number of DCLKs from a Row

Activ ate command to a read or write command.

0 = 3 clocks will be inserted between a row activate command and either a read or write

command.

1 = 2 clocks will be inserted between a row activate and either a read or write command.

0SDRAM RAS# Precharge (SRP). This bit controls the number of DCLKs for RAS# precharge.

0 = 3 clocks of RAS# precharge.

1 = 2 clocks of RAS# precharge.

Bit Description

3-32

82443BX Host Bridge Datasheet

3.3.25 PGPOL—Paging Policy Register (Device 0)

Address Offset: 78–79h

Default Value: 0000h

Access: Read/Write

Size: 16 bits

Bit Description

15:8

Banks per Ro w (BPR). Each bit in this field corresponds to one row of the memory array. Bit 15

corresponds to row 7 while bit 8 corresponds to row 0. These bits are defined only for SDRAM

systems and define whether the corresponding row has a two bank implementation or a four

bank implementation. Those with two banks (bit=0) can ha v e up t o two pages open at an y giv en

time. Those with four banks (bit=1) can have up to four pages open at any time. Note that the

bits referencing empty rows are ‘don’t care’.

0 = 2 banks

1 = 4 banks

7:5 Reserved.

4 Intel Reserved.

3:0

DRAM Idle Timer (DIT). This field determines the number of clocks that the DRAM controller

will remain in the idle state before prechar ging all pages. This field is used for both EDO and

SDRAM memory systems.

0000 = 0 clocks

0001 = 2 clocks

0010 = 4 clocks

0011 = 8 clocks

0100 = 10 clocks

0101 = 12 clocks

0110 = 16 clocks

0111 = 32 clocks

1XXX = Infinite (pages are not closed f or idle condition).

82443BX Host Bridge Datasheet

3-33

3.3.26 PMCR—Power Manag ement Control Register (Device 0)

Address Offset: 7Ah

Default Value: 0000_S0S0b

Access Read/Write

Size 8 Bits

Bit Description

Power Down SDRAM Enab le (PDSE).

1 = Enable . When PDSE=1, an SDRAM row in idle state will be issued a power down

command. The SDRAM row will exit power do wn mode only when there is a request to

access this par ticular row.

0 = Disable

ACPI Control Register Enable (SCRE).

1 = Enable. The ACPI control register in the 82443BX is enabled, and all CPU cycles to IO

address 0022h are handled by the 82443BX and are not forwarded to PCI.

0 = Disable (default). All CPU cycles to IO address 0022h are passed on to the PCI bus.

Suspend Refresh Type (SRT). This bit deter mines what type of EDO DRAM refresh is used

during Power On Suspend (POS/STR) or Suspend to RAM modes. SRT has no effect on

SDRAM refresh.

1 = Self refresh mode

0 = CBR fresh mode

NOTE : When PCIRST# assertion occurs during POS/STR, this bit is not reset to ‘0’.

Normal Refresh Enable (NREF_EN). This bit is used to enable norm al refresh operation

following a POS/STR state. After coming out of reset the software must set this bit before

doing an access to memory.

1 = Enable

0 = Disable

Quick Start Mode (QSTART) (RO).

1 = Quick start mode of operation is enabled f or the processor. This mode is entered using a

strapping option that is sampled by the 82443BX and the CPU during reset. This register

bit is Read Only and a configuration write to it is ignored.

Gated Clock Enable (GCLKEN). GCLKEN enables internal dynamic clock gating in the

82443BX when a AGPset “IDLE” state occurs. This happens when the 82443BX detects an

idle state on all its buses.

1 = Enable

0 = Disable

AGP Disable (AGP_DIS). This register bit is Read Only and a configuration write to it is

ignored.

1 = Disable. The AGP interface and the clocks of AGP associated logic are permanently

disabled. This mode is entered using a strapping option that is sampled by the 82443BX

during reset.

0 = Enable

CPU reset without P CIRST enab le (CRst_En). This bit enables the 82443BX to assert CPU

reset without an incoming PCIRST#. This option allows the reset of the processor when the

system is coming out of POS state. Defaults to ‘0’ upon PCIRST# assertion.

1 = Enable

0 = Disable

NOTE : When PCIRST# assertion occurs during POS/STR, this bit is not reset to ‘0’.

3-34

82443BX Host Bridge Datasheet

3.3.27 SCRR—Suspen d CBR Refresh Rate Register (Device 0)

Address Offset: 7Bh–7Ch

Default Value: 0038h

Access Read/Write

Size 16 Bits

Bit Description

15:13 Reserved.

Suspend CBR refresh Rate Au to Adjust Enab le (SRRAEN). SRRAEN bit is cleared to its default

during cold reset only. It is not affected by PCIRST# dur ing resume from suspend.

0 = Disable (default). Indicates that the suspend CBR refresh rate is not updated by the 82443BX

hardware to track the system operating conditions. In this case, it is expec ted that BIOS will set

the SRR to reflect the worst case operating conditions so that minimum refresh rate will be

provided.

1 = Enable. Indicates that the 82443BX hardware adjusts the suspend refresh rate according to

system operating conditions by comparing the number of OSCCLKs in a given time. This mode

allows the system to dynamically adjust the refresh rate and thus minimize suspend power

consumption while guaranteeing required refresh rate.

11:0

Suspend CBR Refresh Rate (SRR). The r ate is loaded into the counter which counts down on

OSCCLK rising edges. When it expires, a suspend CBR refresh request is triggered. This bit field

may be loaded by BIOS to reflect the desirable refresh r ate. In addition, the 82443BX will update it

automatically, when the above SRRAEN = 1. In either case, the register is accessible for read and

write operation at all times.

• This 12-bit field provides a dynamic range gr eater than the maximum CBR refresh rate that is

supported of 249.6uSEC.

• SRR bit field is cleared to its def aul t during cold reset only. It is not affected b y PCIRST# during

resume from suspend.

• The default value of this register is 038h, or 56 decimal. It represents a 15.5uS time between

refreshes with the slowest corner OSCCLK cycle time of 270nS.

82443BX Host Bridge Datasheet

3-35

3.3.28 EAP—Err or Address Pointer Register (Device 0)

Address Offset: 80–83h

Default Value: 00000000h

Access Read Only, Read/Write-Clear

Size 32 Bits

Bit Description

31:12

Error Address Pointer (EAP) (RO). This field is used to store the 4 KB bloc k of main memory

of which an error (single bit or multi-bit error) has occurred. Note that this field represents the

address of the f irst error occurrence after bits 1:0 ha v e been cleared b y softw are . Once bits 1:0

are set to a value different than 00b, as a result of an error, this bit field is locked and doesn't

change as a result of a new error.

11:2 Reserved.

Multiple Bit Error (MBE) (R/W C). This bit indicates that a multi-bit ECC error has occurred,

and the address has been logged in bits 31:12. The EAP register is locked until the CPU

clears this bit by writing a 1. Software uses bits 1:0 to detect whether the logged error address

is for Single or Multi bit error, since both Single and Multiple Error bits of the Error Status

this bit field to clear the value (bac k to 0) and unlock the error logging mechanism.

Note: Any ECC errors received during initialization should be ignored.

Single Bit Error (SBE) (R/WC).

1 = Indicates that a single bit ECC error has occurred, and the address has been logged in bits

31:12. The EAP register is locked until the CPU clears this bit by writing a 1.

Note: Any ECC errors received during initialization should be ignored.

3-36

82443BX Host Bridge Datasheet

3.3.29 ERRCMD—Error Command Register (Device 0)

Address Offset: 90h

Default Value: 80h

Access: Read/Write

Size: 8 bits

This 8-bit register contro ls the 82443BX responses to v arious system errors. The actual assertion of

SERR# is enabled via the PCI Command register.

Bit Description

SERR# on AGP Non-Snoopable Access Outside of Graphics Aperture. When enabled and

bit 10 of ERRSTS registers tr ansitions from 0 to 1 (during an A GP access to the address outside

of the graphics aperture) then an SERR# assertion event will be generated.

1 = Enable (default ).

0 = Disable.

SERR# on Invalid AGP DRAM Access. AGP non-snoopable READ accesses to locations

outside the graphics aperture and outside the main DRAM range (i .e., in 640 KB – 1 MB range or

above top of memory) are invalid. When this bit is set, bit 9 of the ERRSTS will be set and

SERR# will be assert ed, read accesses are not directed to main memory or the aperture range.

1 = Enable.

0 = Disable reporting of this condition via SERR#.

SERR# on Access to Invalid Graphics Aperture Translation Table Entry. When enabled, the

82443BX sets bit 8 of the ERRSTS and asserts SERR# following a read or write access to an

invalid entry in the Graphics Aperture Translation Table residing in main memory.

1 = Enable.

0 = Disable reporting of this condition via SERR#.

4SERR# on Receiving Target Abort.

1 = Enable. The 82443BX asserts SERR# on receiving a target abort on either the PCI or AGP.

0 = Disable . The 82443BX does not assert SERR# on receipt of a target abort.

SERR# on Detected Thermal Throttling Condition.

1 = Enable . The 82443BX asserts SERR# when thermal throttling condition is detected for either

the read or the write function.

0 = The 82443BX does not assert SERR# for thermal throttling.

SERR# Assertion Mode.

1 = SERR# is a level mode si gnal. Systems that connect SERR# to EXTSMI# for error reporting

should set this bit to 1.

0 = SERR# is asserted f or 1 PCI clock (normal PCI mode). (default)

SERR# on Receiving Multiple-Bit ECC/Parity Error. When enabled, the 82443BX asserts

SERR# when it detects a multiple-bit error reported by the DRAM controller. For systems not

supporting ECC this bit must be disabled.

1 = Enable.

0 = Disable .

Note: Any ECC errors received during initialization should be ignored.

SERR# on Receiving Single-bit ECC Error. When enabled, the 82443BX asserts SE RR#

when it detects a single-bit ECC error. For systems not supporting ECC, this bit must be

disabled.

1 = Enable.

0 = Disable .

Note: Any ECC errors received during initialization should be ignored.

82443BX Host Bridge Datasheet

3-37

3.3.30 ERRSTS—Error Status Register (Device 0)

Address Offset: 91–92h

Default Value: 0000h

Access: Read Only, Read/Write Clear

Size: 16 bits

This 16-bit register is used to report error conditions via the SERR# mechanism. SERR# is

generated on a zero to one transition of any of these flags (if enabled by the ERRCMD register).

Bit Description

15:13 Reserved.

12 Read thermal Throttling Condition.

1 = Read thermal throttling condition occurred.

0 = Software writes “1” to clear this bit. Default=0

11 Write Thermal Throttling Condition.

1 = Write thermal throttling condition occurred.

0 = Software writes “1” to clear this bit. Default=0

10 AGP non-snoopable access outside of Graphics Aperture.

1 = AGP access occurred to the address that is outside of the graphics aperture range.

0 = Software writes “1” to clear this bit. Default=0

Invalid AGP non-snoopable DRAM read access (R/WC).

1 = AGP non-snoopable READ access was attempted outside of the graphics aperture and

outside of main memory (i.e, . in 640 KB – 1 MB range or above top of memory).

0 = Software must write a “1” to clear this status bit.

Access to Invalid Graphics Aperture Translation Table Entry (AIGATT) (R\WC).

1 = An in valid translation tab le entry was returned in response to a graphics aperture read or write

access.

0 = Software must write a “1” to clear this bit.

7:5

Multi-bit First Error (MBFRE) (RO). This field contains the encoded val ue of the DRAM row in

which the first multi-bit error occurred. A simple binary encoding is used to indicate the row

containing the multi -bit error . When an error is detected, this f ield is updated and the MEF bit is set.

This field will then be loc ked (no further updates) until the MEF flag has been reset. If MEF is 0, the

value in this field is undefined.

000 = Row 0

001 = Row 1

...

111 = Row 7

Multiple-bit ECC (uncorrectable) Error Flag (MEF) (R/WC).

1 = Memory data transfer had an uncorrectable error(i.e., multiple-bit error). When enabled, a

multiple bit error is reported by the DRAM controller and propagated to the SERR# pin, if

enabled by bit 1 in the ERRCMD register.

0 = BIOS writes a 1 to clear this bit and unlock the MBFRE field. (Default = 0).

3:1

Single-bit First Row Err or (SBFRE) (RO). This field contains the encoded v alue of the DRAM row

in which the first single-bit error occurred. A simple binary encoding is used to indicate the row

containing the single-bit error. When an error is detected, this field is updated and SEF is set. This

field is then locked (no further updates) until the SEF flag has been reset. If SEF is 0, the value in

this field is undefined.

000 = Row 0

001 = Row 1

...

111 = Row 7

Single-bit (correctable) ECC Error Flag (SEF) (R/WC).

1 = Memory data transf er had a single-bit correctable error and the corrected data was sent f or the

access. When ECC is enabled, a single bit error is reported and propagated to the SERR# pin,

if enabled b y bit 0 in the ERRCMD register .

0 = BIOS writes a 1 to clear this bit and unlock the SBFRE field.

3-38

82443BX Host Bridge Datasheet

3.3.31 ACAPID—AGP Capability Identifier Register (Device 0)

Address Offset: A0–A3h

Default Value: 00100002h/00000000h

Access: Read Only

Size: 32 bits

This register provides normal identifier for AGP capability.

3.3.32 AGPSTAT—AGP Status Register (Device 0)

Address Offset: A4–A7h

Default Value: 1F000203h

Access: Read Only

Size: 32 bits

This register reports AGP compliant device capability/status.

Bit Description

31:24 Reserved

23:20

Major AGP Revision Number. This field provides a major re vision number of AG P specification to

which this version of the 82443BX conforms. When the AGP DIS bit (PMCR[1]) is set to 0, this

number is set to value of “0001b” (i.e., implying Rev 1.x). When the A GP DIS bit (PMCR[1]) is set

to 1, This number is set to “0000b”.

19:16

Minor AGP Revision Number. These bits provide a minor revision number of AGP specification

to which this version of 82443BX conforms. This number is hardwired to value of “0000” (i.e.,

implying Rev x.0). Together with major revision number this field identifies 82443BX as an A GP

REV 1.0 compliant device.

15:8 Next Capability Pointer. AGP capability is the first and the last capability described via the

capability pointer mechanism.

0s = Hardwired to 0s to indicate the end of the capability linked list.

7:0 AGP Capability ID. This field identifies the linked list item as containing AGP registers. When the

A GP DIS bit (PMCR[1]) is set to 0, this field has a value of 0000_0010b assigned by the PCI SIG.

When the AGP DIS bit (PMCR[1]) is set to 1, this field has a value of 00h.

Bit Description

31:24 AGP Maximum Request Queue Depth (RO). This field is hardwired to 1Fh to indicate a

maximum of 32 outstanding AGP command requests can be handled by the 82443BX.

23:10 Reserved

9AGP Side Band Addressing Supported. This bit indicates that the 82443BX supports side band

addressing. It is hardwired to 1.

8:2 Reserved

1:0

AGP Data Transfer Type Supported (R/W). Bit 0 identifies if AGP compliant device supports 1x

data transfer mode and bit 1 identifies if AGP compliant device supports 2x data transf er mode .

Configuration software will update this field by setting only one bit that corresponds to the

capability of AGP master (after that capability has been verified by accessing the same functional

00 = Not allowed

01 = 1x data transfer mode supported

10 = 2x data transfer mode supported

11 = (default)

NOTE: The selected data transfer mode apply to both AD bus and SBA bus.

82443BX Host Bridge Datasheet

3-39

3.3.33 AGPCMD—AGP Command Register (Device 0)

Address Offset: A8–ABh

Default Value: 00000000h

Access: Read/Write

Size: 32 bits

This register provides control of the AGP operational parameters.

Bit Description

31:10 Reserved.

9AGP Side Band Enable. This bit enables the side band addressing mechanism.

1 = Enable.

0 = Disable.

AGP Enable. When disabled, the 82443BX ignores all AGP operations, including the sync

cycle. Any A GP operations received while t his bit is set to 1 is serviced ev en if this bit is reset

to 0. If this bit transitions from a 1 to a 0 on a clock edge in the middle of an SBA command

being delivered in 1X mode the command will be issued. When this bit is set to 1 the

82443BX will respond to AGP operations delivered via PIPE#, or to operations delivered via

SBA if the AGP Side Band Enable bit is also set to 1.

The AGP parameters in the AGPCMD and A GPCTRL registers must be set prior to setting

this bit ‘1’. With the exception of the GTLB_ENABLE (bit 7, AGPCTRL), and ATTBASE

1 = Enable.

0 = Disable.

7:2 Reserved.

1:0

AGP Data Transfer Rate. One (and only one) bit in this field must be set to indicate the

desired data transf er r ate (Bit 0 for 1X, Bit 1 for 2X). The same bit must be set on both master

and target. Configuration software will update this fiel d by setting only one bit that

corresponds to the capability of AG P m aster (after that capability has been verified by

accessing the same functional register within the AGP masters configuration space.)

00 = default

01 = 1x data transfer rate.

10 = 2x data transfer rate.

11 = Illegal

NOTE: This field applies to AD and SBA buses.

3-40

82443BX Host Bridge Datasheet

3.3.34 AGPCTRL—AGP Control Register (Device 0)

Address Offset: B0–B3h

Default Value: 00000000h

Access: Read/Write

Size: 32 bits

This register provides for additional control of the AGP interface.

Bit Description

31:16 Reserved.

Snoopabl e Writes In Order With AGP Reads Disable (AGPDCD). When set to 0 (default), the

82443BX maintains ordering between snoopable write cycles and AGP reads. When set to 1, the

82443BX handles the AGP reads and snoopab le writes as independent streams.

AGPDCD AGPRSE Description

(Bit 15) (Bit 13)

0 0 DWB is visible to AGP reads. DWB flushes only when address hit.

0 1 Illegal.

1 0 Illegal

1 1 DWB flushes when write to AG P occurs

14 Reserved

Graphics Aperture Write-AGP Read Synchronization Enable (AGPRS E). When this bit is set

the 82443BX will ensure that all writes posted in the Global Write Buffer to the Graphics Aper ture

are retired to DRAM before the 82443BX will initiate any CPU-to-AGP cycle. This can be used to

ensure synchronization between the CPU and AGP mas ter. The AGPDCD bit description defines

the interaction between the AG PRSE bit and the AGP DCD bit.

1 = Enable

0 = Disable (Default)

12:8 Reserved

7GTLB Enable (and GTLB Flush Control).

1 = Enable. Normal operations of the Graphics Translation Lookaside Buffer.

0 = Disable (default). The GTLB is flushed b y clearing the vali d bits associated with each entry.

6:0 Reserved.

82443BX Host Bridge Datasheet

3-41

3.3.35 APSIZE—Aperture Size Register (De vice 0)

Address Offset: B 4h

Default Value: 00h

Access: Read/Write

Size: 8 bits

This register determines the effective size of the Graphics Aperture used for a particular 82443BX

conf igur atio n. This re gist er can be updated by t he 82443BX- specific BIOS config uration sequence

before the PCI normal bu s enumeration sequence takes place. If the register is not updated, a

default value selects an aperture of maximum size (i.e., 256 MB). The size of the table that will

correspond to a 256 MB aperture is not practical for most applications and, therefore, these bits

must be programmed to a smaller practical value that forces adeq uate address range to be requested

via the APBASE register from the PCI configuration software.

3.3.36 ATTBASE—Aperture Translation Table Base Register

(Device 0)

Address Offset: B 8–BBh

Default Value: 00000000h

Access: Read/Write

Size: 32 bits

This register provides the starting address of the Graphics Aperture Translation Table base located

in the main DRAM. The ATTBASE register may be dynamically changed.

Note: The address provided via ATTBASE is 4KB aligned.

Bit Description

7:6 Reserved.

5:0

Graphics Aperture Size (APSIZE) (R/W). Each bit in APSIZE[5:0] operates on similarly ordered

bits in APBASE[27:22] of the Aperture Base configur ation register. When a particular bit of this f ield

is “0”, it forces the similarly ordered bit in APBASE[27 :22] to behave as “hardwired” to 0. When a

particular bit of this field is set to “1”, it allows corresponding bit of the APBASE[27:22] to be read/

write accessible. Only the following combinations are allowed:

11 1111 = 4 MB

11 1110 = 8 MB

11 1100 = 16 MB

11 1000 = 32 MB

11 0000 = 64 MB

10 0000 = 128 MB

00 0000 = 256MB

Def ault for APSIZE[5:0]=000000b forces default APBASE[27:22] =000000b (i.e., all bits respond as

“hardwired” to 0). This provides maximum aperture size of 256 MB. As another example,

programming APSIZE[5:0]=111000b hardwires APBASE[24:22]=000b and while enabling

APBASE [27:25] as read/write programmable.

Bit Description

31:12 Aperture Translation Table Base Address. Bits 31:12 correspond to address bits 31:12,

respectively. This field contains a pointer to the base of the translation table used to map memory

space addresses in the aperture range to addresses in main memory.

11:0 Reserved.

3-42

82443BX Host Bridge Datasheet

3.3.37 MBFS—Memory Buffer Frequency Select Register

(Device 0)

Address Offset: CA–CCh

Default Value: 000000h

Access: Read/Write

Size: 24 bits

The settings in this register enable the 100 MHz or 66 MHz b uf fers for each of th e follo wing signal

groups.

Note: The choice of 1 00 MHz or 66 MHz buffer is independ ent o f bus freq uency. It is po ssible to select a

100 MHz memory buffer even though the bus frequency is 66 MHz (and vice versa).

Bit Description

23 Reserved

MAA[13:0], WEA#, SRASA#, SCASA# (100 MHz/66 MHz buffer select bit). This bit enables

either 100 MHz or 66 MHz buffers for MAA[13:0], WEA#, SRASA #, SCASA #.

0 = 66 MHz

1 = 100 MHz

MAB[12:11, 9:0]# & MAB[13,10], WEB#, SRASB#, SCASB# (100 MHz/66 MHz buffer select

bit). This bit enables either 100 MHz or 66 MHz buffers for MAB[12:11, 9:0]# & MAB[13,10],

WEB#, SRASB#, SCASB#. Note that the address’s MABx# are inverted copies of MAA, with the

exception of MAB[13,10].

0 = 66 MHz

1 = 100 MHz

MD [63:0] (100 MHz/66 MHz b uffer select bit [Control 2]). This bit enables either 100 MHz or

66 MHz buffers for MD [63:0] [Control 2]. (Refer to the corresponding MBSC register for

programming details).

0 = 66 MHz

1 = 100 MHz

MD [63:0] (100 MHz/66 MHz b uffer select bit [Control 1]). This bit enables either 100 MHz or

66 MHz buffers for MD [63:0] [Control 1]. (Refer to the corresponding MBSC register for

programming details).

0 = 66 MHz

1 = 100 MHz

MECC [7:0] (100 MHz/66 MHz buffer select bit [Control 2]). This bit enables either 100 MHz or

66 MHz buffers for MECC [7:0] [Control 2]. (Refer to the corresponding MBSC register for

programming details).

0 = 66 MHz

1 = 100 MHz

MECC [7:0] (100 MHz/66 MHz buffer select bit [Control 1]). This bit enables either 100 MHz or

66 MHz buffers for MECC [7:0] [Control 1]. (Refer to the corresponding MBSC register for

programming details).

0 = 66 MHz

1 = 100 MHz

CSB7#/CKE5 (100 MHz/66 MHz buffer select bit). This bit enables either 100 MHz or 66 MHz

buffers for CSB7#/CKE5.

0 = 66 MHz

1 = 100 MHz

82443BX Host Bridge Datasheet

3-43

CSA7#/CKE3 (100 MHz/66 MHz buffer select bit). This bit enables either 100 MHz or 66 MHz

buffers for CSA7#/CKE3.

0 = 66 MHz

1 = 100 MHz

CSB6#/CKE4 (100 MHz/66 MHz buffer select bit). This bit enables either 100 MHz or 66 MHz

buffers for CSB6#/CKE4.

0 = 66 MHz

1 = 100 MHz

CSA6#/CKE2 (100 MHz/66 MHz buffer select bit). This bit enables either 100 MHz or 66 MHz

buffers for CSA6#/CKE2.

0 = 66 MHz

1 = 100 MHz

CSA5#/RASA5#, CSB5#/RASB5# (100 MHz/66 MHz buffer select bit). This bit enab les either

100 MHz or 66 MHz buffers for CSA5#/RASA5#, CSB5#/RASB5#.

0 = 66 MHz

1 = 100 MHz

CSA4#/RASA4#, CSB4#/RASB4# (100 MHz/66 MHz buffer select bit). This bit enables either

100 MHz or 66 MHz buffers for CSA4#/RASA4#, CSB4#/RASB4#.

0 = 66 MHz

1 = 100 MHz

CSA3#/RASA3#, CSB3#/RASB3# (100 MHz/66 MHz buffer select bit). This bit enables either

100 MHz or 66 MHz buffers for CSA3#/RASA3#, CSB3#/RASB3#.

0 = 66 MHz

1 = 100 MHz

CSA2#/RASA2#, CSB2#/RASB2# (100 MHz/66 MHz buffer select bit). This bit enables either

100 MHz or 66 MHz buffers for CSA2#/RASA2#, CSB2#/RASB2#.

0 = 66 MHz

1 = 100 MHz

CSA1#/RASA1#, CSB1#/RASB1# (100 MHz/66 MHz buffer select bit). This bit enables either

100 MHz or 66 MHz buffers for CSA1#/RASA1#, CSB1#/RASB1#.

0 = 66 MHz

1 = 100 MHz

CSA0#/RASA0#, CSB0#/RASB0# (100 MHz/66 MHz buffer select bit). This bit enables either

100 MHz or 66 MHz buffers for CSA0#/RASA0#, CSB0#/RASB0#.

0 =66 MHz

1 = 100 MHz

DQMA5/CASA5# (100 MHz/66 MHz buffer select bit). This bit enables either 100 MHz or 66

MHz buffers for DQMA5/CASA5#.

0 = 66 MHz

1 = 100 MHz

DQMA1/CASA1# (100 MHz/66 MHz buffer select bit). This bit enables either 100 MHz or 66

MHz buffers for DQMA1/CASA1#.

0 = 66 MHz

1 = 100 MHz

DQMB5/CASB5# (100 MHz/66 MHz buffer select bit). This bit enables either 100 MHz or 66

MHz buffers for DQMB5/CASB5#.

0 = 66 MHz

1 = 100 MHz

Bit Description

3-44

82443BX Host Bridge Datasheet

3.3.38 BSPAD—BIOS Scratch Pad Register (Device 0)

Address Offset: D0–D7h

Default Value: 0000-0000-0000-0000h

Access: Read/Write

Size: 64 bits

This register provides 8 bytes general purpose read/write registers for the BIOS to perform the

config uration routine. The 82 443BX will provide this 8 b yte re gister in the PCI conf iguration space

of the 82443BX device0 on bus 0. The registers in this range will be defined as read/write and will

be initialized to all 0’s after PCIRST#. The BIOS will can access th ese re gisters through the n ormal

PCI configuration register mechanism, accessing 1,2 or 4 bytes in every data access.

3.3.39 DWTC—DRAM Write Thermal Throttling Control Register

(Device 0)

Offset: E0h–E7h

Default: 0000_0000_0000_0000h

Access: Read/Write/Lock

Size: 64 bits

A locking mechanism is included to protect contents of this register as well as the DRAM Read

Thermal Throttling C ontrol regist er desc ribed below.

DQMB1/CASB1# (100 MHz/66 MHz buffer select bit). This bit enables either 100 MHz or 66

MHz buffers for DQMB 1/CASB1#.

0 = 66 MHz

1 = 100 MHz

DQMA[7:6,4:2,0]/CASA[7:6 ,4:2,0]# (100 MHz/66 MHz buffer select bit). This bit enables

either 100 MHz or 66 MHz buffers for DQMA[7:6]/CASA[7:6]#, DQMA[4:2]/CASA[4:2]#, and the

DQMA[0]/CASA[0]#.

0 = 66 MHz

1 = 100 MHz

CKE1/GCKE (100 MHz/66 MHz buffer select bit). This bit enab les either 100 MHz or 66 MHz

buffers forCKE1.

0 = 66 MHz

1 = 100 MHz

CKE0/FENA (100 MHz/66 MHz buffer select bit). This bit enables either 100 MHz or 66 MHz

buffers for CKE0/FENA.

0 = 66 MHz

1 = 100 MHz

Bit Description

64:0 BIOS Work Space.

82443BX Host Bridge Datasheet

3-45

Bits Description

Throttle Lock (TLOCK). This bit secures the DRAM thermal throttling control registers.

1 = All configuration register bits in E0h–E7h and E8h–EFh (read throttle control) become read-

only.

0 = Default

62:46 Reserved

45:38 Global DRAM Write Sampling Window (GDWSW). This 8-bit value is multiplied by 4 to define

the length of time in milliseconds (0–1020) over which the number of QWords written is counted.

37:26 Global QWord Threshold (GQT). The 12-bit value held in this field is multiplied by 215 to arrive

at the number of QW ords that must be written within the Global DRAM Write Sampling Window in

order to cause the thermal throttling mechanism to be invoked.

25:20

Thr ottle Time (TT). This value provides a multiplier between 0 and 63 which specifies how long

thermal throttling remains in effect as a number of Global DRAM Write Sampling Windows . For

example, if GDWSW is programmed to 1000_0000b and TT is set to 01_0000b, then ther mal

throttling will be performed for ~2 seconds once in vok ed (128 ms * 16).

19:13

Thr ottle Mo nitoring Window (TMW). The val ue in this register is padded with four 0’s to specify

a window of 0–2047 DRAM CLKs with 16 clock granularity. While the thermal throttling

mechanism is inv oked, DRAM writes are monitored during this window—if the number of QW ords

written during the window reaches the Throttle QWord Maximum, then write requests are block ed

for the remainder of the window.

12:3 Thr ott le QWor d Maximum (TQM). The Throttle QW ord Maximum defines the maximum number

of QWords between 0–1023 which are permitted to be written to DRAM within one Throttle

Monitoring Window while the thermal throttling mechanism is in effect.

2:0

DRAM Write Thr ottle Mode. Normal DRAM write monitoring and thermal throttling oper ation are

enabled when bits 2:0 are set to 100. All other combinations are Intel Reserved.

000-011 = Intel Reserved

100 = Normal Operations

101-111 = Intel Reserved

3-46

82443BX Host Bridge Datasheet

3.3.40 DRTC—DRAM Read Thermal Throttling Control Register

(Device 0)

Offset: E8h–EFh

Default: 0000_0000_0000_0000h

Access: Read/Write/Lock

Size: 64 Bits

The contents of this register are protected by making the bits read-only once a ‘1’ is written to the

Throttle Lock bit (b it 63 of configuration register E0–E7h)

Bits Description

63:46 Reserved

45:38 Global DRAM Read Sampling Window (GDRSW). This 8-bit value is multiplied by 4 to define

the length of time in milliseconds (0–1020) over which the number of QW ords read from DRAM is

counted.

37:26 Global Read QWord T hreshold (GRQT) . The 12-bit v alue held in this field is mul tiplied by 215 to

arrive at the number of QWor ds that must be written within the Global DRAM Read Sampling

Window in order to cause the thermal throttling mechanism to be invoked.

25:20

Read Thr ottle Time (RTT). This value provides a multiplier between 0 and 63 which specifies

how long read thermal throttling remains in effect as a number of Global DRAM Read Sampling

Windows . For example, if GDRSW is programmed to 1000_0000b and R TT is set to 01_0000b,

then read thermal throttling will be performed for ~2 seconds once invoked (128 ms * 16).

19:13

Read Thr ottle Monitoring Windo w (RTMW). The value in this register is padded with 4 0’s to

specify a window of 0–2047 DRAM CLKs with 16 clock granularity. While the thermal throttling

mechanism is invok ed, DRAM reads are monitored during this window—if the number of QWords

read during the window reaches the Throttle QWord Maximum, then Host and PCI read requests,

as well as all AGP requests, are b locked for the remainder of the window.

12:3 Read Throttle QWord Maximum (RTQM). The Read Throttle QWord Maximum defines the

maximum number of QWords between 0–1023 which are permitted to be read from DRAM within

one Read Throttle Monitor ing Window while thermal throttling mechanism is in effe ct.

2:0

DRAM Read Thr ottle Mode. Normal DRAM read monitoring and thermal throttling operation are

enabled when bits 2:0 are set to 100. All other combinations are Intel Reser ved.

000-011 = Intel Reserved

100 = Normal Operations

101-111 = Intel Reserved

82443BX Host Bridge Datasheet

3-47

3.3.41 BUFFC—Buffer Control Register (Device 0)

Offset: F0–F1h

Default: 0000h

Access: Read/Write

Size: 16 bits

The Jam Latch design provides the AGP sub-system with a variable strength, to better

accommodate the clamping requirements.

The Jam Latch Register should be enabled by the BIOS during the resume sequence from STR, if

these Jam Latch control bits had been enabled before the STR was executed.

Bit Description

15:10 Reserved.

9:6

AGP Jam Latch Strength Select.

Bit 9 = 1; Enable strong pull-up

Bit 8 = 1; Enable weak pull-up

Bit 7 = 1; Enable strong pull-down

Bit 6 = 1; Enable weak pull-down

5:0 Intel Reserved.

3-48

82443BX Host Bridge Datasheet

3.4 PCI-to-PCI Bridge Registers (Device 1)

The configuration space for device #1 is controlled by the AGP_DIS bit in the PMCR register.

Note: When AGP_DIS = 0, the configuration space for device #1 is enabled, and the registers defined

below are accessible through the configuration mechanism defined in the first section of this

document.

Note: When the AGP_DIS = 1, the config uration space f or de vice #1 is disabled. All con f iguration c ycles

(reads and writes) to de vice #1 of b us 0 will cause the master abort status bit for de vice #0/ b us 0 to

be set. Configuration read c ycles will return data of all 1’s. Configuration write cycles will have no

eff ect on the registers.

Table 3-4. 82443BX Configuration Space—Device 1

Address

Offset Register

Symbol Register Name Default

Value Access

00–01h VID1 Vendor Identification 8086h RO

02–03h DID1 Device Identification 7191h RO

04–05h P CICMD1 PCI Command Register 0000h R/W

06–07h PCISTS1 PCI Status Register 0220h RO, R/WC

08h RID1 Revision Identification 00/01h RO

09h — Reserved 00h —

0Ah SUBC1 Sub-Class Code 04h RO

0Bh BCC1 Base Class Code 06h RO

0Ch — Reserved 00h —

0Dh MLT1 Master Latency Timer 00h R/ W

0Eh HDR1 Header Type 01h RO

0F–17h — Reserved 00h —

18h PBUSN P r imary Bus Num ber 00h RO

19h SBUSN Secondary Bus Number 00h R/W

1Ah SUBUSN Subordinate Bus Number 00h R/W

1Bh SMLT S econdary Bus Mas ter Latency Timer 00h R/W

1Ch IOBASE I/O Base Address Register F0h R/W

1Dh IOLIMIT I/O Limit Address Register 00h R/W

1E–1Fh SSTS Secondary PCI-to-PCI Status Register 02A0h R/WC, RO

20–21h MB AS E M emory Base Addr ess Register FFF0h R/W

22–23h MLIMIT Memory Limit Address Register 0000h R/W

24–25h PM BA SE P refetchable Memor y Base Addres s Reg. FFF0h R/W

26–27h PMLIMIT Prefetchable Memory Limit Address Reg. 0000h R/W

28–3Dh — Reserved 0 c

3Eh BCTRL Bridge Control Register 80h R/W

3F–FFh — Reserved 00h —

82443BX Host Bridge Datasheet

3-49

3.4.1 VID1—Vendor Identifi cation Register (Device 1)

Address Offset: 00–01h

Default Value: 8086h

Attribute: Read Only

Size: 16 bits

The VID Register contains the vendor identification number. This 16-bit register combined with

the Device Identification Register uniquely identify any PCI device. Writes to this register have no

effect.

3.4.2 DID1—Device Identification Register (Device 1)

Address Offset: 02–03h

Default Value: 7191h

Attribute: Read Only

Size: 16 bits

This 16-bit register combined with th e Vendor Identification register uniquely identifies any PCI

device. Writes to this register have no effect.

Bit Description

15:0 Vendor Identification Number. This is a 16-bit value assigned to Intel. Intel VID = 8086h.

Bit Description

15:0 Device Identification Number. This is a 16 bit value assigned to the 82443BX device #1.

82443BX device #1 DID =7191h.

3-50

82443BX Host Bridge Datasheet

3.4.3 PCICMD1—PCI-to-PCI Command Register (Device 1)

Address Offset: 04–05h

Default: 0000h

Access: Read/Write

Size 16 bits

Bit Descriptions

15:10 Reserved.

9Fast Back-t o-Back: Not Applicable. Hardwired to 0.

SERR# Enable (SERRE1). When enabled the SERR# signal driv er (common for PCI and AGP)

is enabled for error conditions that occur on AGP.If both SERRE and SERRE1 are reset to 0,

then SERR# is ne v er driv en b y the 82443BX. Also, if this bit is set and the P arity Error Response

Enable Bit (Dev 01h, Register 3Eh, Bit 0) is set, then the 82443BX will report ADDRESS and

DATA parity errors on AGP.

1 = Enable .

0 = Disable .

7Address/Data Stepping. Not applicable. Hardwired to 0.

6Parity Error Enable (PERRE1). Hardwired to 0.

5Reserved.

4Memory Write and Invalidate Enable: Not applicable. Ho wever, supported as a read/write bit

to avoid the problems with normal PCI-to-PCI Bridge configur ation software.

3Special Cycle Enable: Not applicable. However, supported as a read/write bit to avoid the

problems with nor mal PCI-to-PCI Bridge configuration software.

2Bus Master Enable (BME1): Not applicable. How ever, supported as a read/write bit to avoid

the problems with norm al PCI-to-PCI Bridge configuration software.

1Memory Access Enable (MAE1): Not applicable. However, supported as a read/write bit to

avoid the problems with normal PCI-to-PCI Bridge configuration software.

0I/O Access Enable (IOAE1): Not applicab le. However, supported as a read/write bit to avoid

the problems with norm al PCI-to-PCI Bridge configuration software.

82443BX Host Bridge Datasheet

3-51

3.4.4 PCISTS1—PCI-to-PCI Status Register (Device 1)

Address Offset: 06–07h

Default Value: 0220h

Access: Read Only, Read/Write Clear

Size: 16 bits

PCISTS1 is a 16-bit status register that reports the occurrence of error conditions associated with

primary side of the “virtual” PCI-to-PCI bridge embedded within the 82443BX.

3.4.5 RID1—Revision Identification Register (Device 1)

Address Offset: 08h

Default Value: 00/01h

Access: Read Only

Size: 8 bits

This register contains the revision number of the 82443BX device #1. These bits are read only and

writes to this register have no effect. For the A-0 Stepping, this value is 00h.

Bit Descriptions

15 Detected Parity Error (DPE1). Not Applicable. Hardwired to 0.

14 Reserved.

13 Received Master Abort Status (RMAS1). Not Applicable. Hardwired to 0.

12 Received Target Abort Status (RTAS1). Not Applicable. Hardwired to 0.

11 Signaled Target Abort Status (STAS1). Not Applicable. Hardwired to 0.

10:9 DEVSEL# Timing (DEVT1). Not Applicable. Hardwired to “01b”.

8Data Parity Detected (DPD1). Not Applicable. Hardwired to 0.

7Fast Back-to-Back (FB2B1). Not Applicable . Hardwired to 0.

6 Reserved.

566/60 MHz Capability. Hardwired to “1”.

4:0 Reserved.

Bit Description

7:0 Revision Identification Number. This is an 8-bit value that indicates the revision identification

number for the 82443BX device #1.

02h = B1 stepping

3-52

82443BX Host Bridge Datasheet

3.4.6 SUBC1—Sub-Class Code Register (Device 1)

Address Offset: 0Ah

Default Value: 04h

Access: Read Only

Size: 8 bits

This register co ntains the Sub-Class Code for the 82443 BX device # 1. This code is 04h indicating a

PCI-to-PCI Bridge device. The register is read only.

3.4.7 BCC1—Base Class Code Register (Device 1)

Address Offset: 0Bh

Default Value: 06h

Access: Read Only

Size: 8 bits

This re gister con tains the Base Clas s Code of th e 82443BX de vice # 1. This code is 06h indicating a

Bridge device. This register is read only.

3.4.8 MLT 1—Master Latency Timer Register (Device 1)

Address Offset: 0Dh

Default Value: 00h

Access: Read/Write

Size: 8 bits

This functionality is not applicable. It is described here since these bits should be implemented as a

read/write to comply wit h the normal PCI-to-PCI bridge configuration software.

Bit Description

7:0 Sub-Class Code (SUBC1). This is an 8-bit value that indicates the category of Bridge into which

the 82443BX falls.

04h = Host Bridge.

Bit Description

7:0 Base Class Code (BASCC). This is an 8-bit value that indicates the Base Class Code for the

82443BX device #1.

06h = Bridge device.

Bit Description

7:3 Not applicable but suppor t read/write operations. (Reads return previously written data.)

2:0 Reserved.

82443BX Host Bridge Datasheet

3-53

3.4.9 HDR1—Header Type Register (Device 1)

Offset: 0Eh

Default: 01h

Access: Read Only

Size: 8 bits

This register identifies the header layout of the configuration space. No physical register exists at

this location.

3.4.10 PBUSN—Primary Bus Number Register (Device 1)

Offset: 18h

Default: 00h

Access: Read Only

Size: 8 bits

This register identifies that “virtual” PCI-to-PCI bridge is connected to bus #0.

3.4.11 SBUSN—Secondary Bus Number Register (De vice 1)

Offset: 19h

Default: 00h

Access: Read /Write

Size: 8 bits

This register identifies the bus number assigned to the second bus side of the “virtual” PCI-to-PCI

bridge i.e. to AGP. This number is programmed by the PCI configuration software to allow

mapping of configuration cycles to AGP.

Bit Descriptions

7:0 Header Type (HEADT). This read only field always returns 01h when read. Writes have no effect.

Bit Descriptions

7:0 Bus Number. Hardwired to “0”.

Bit Descriptions

7:0 Bus Number. Programmable

Default “0”.

3-54

82443BX Host Bridge Datasheet

3.4.12 SUBUSN—Subor dinate Bus Number Register (Device 1)

Offset: 1Ah

Default: 00h

Access: Read /Write

Size: 8 bits

This register identifies the subordinate bus (if any) that resides at the le v el belo w A GP.This number

is programmed b y the PCI conf iguration softwar e to allo w mapping of conf iguration c ycles to A GP.

3.4.13 SMLT—Secondary Master Latency Timer Register

(Device 1)

Address Offset: 1Bh

Default Value: 00h

Access: Read/Write

Size: 8 bits

This register control the bus tenure of the 82443BX on AGP the same way the Device 0 MLT

controls the access to the PCI bus.

3.4.14 IOBASE—I /O Base Address Register (Device 1)

Address Offset: 1Ch

Default Value: F0h

Access: Read/Write

Size: 8 bits

This register control the CPU to AGP I/O access routing based on the following formula:

IO_BASE= < ad dress = <IO_LIMIT

Bit Descriptions

7:0 Bus Number. Programmable .

Bit Description

7:3 Secondary MLT Counter Value . The default is 0s (i.e,. SMLT disabled)

2:0 Reserved.

Bit Description

7:4 I/O Address Base. Corresponds to A[15:12] of the I/O address. Default = Fh

3:0 Reserved.

82443BX Host Bridge Datasheet

3-55

3.4.15 IOLIMIT—I/O Limit Address Register (Device 1)

Address Offset: 1Dh

Default Value: 00h

Access: Read/Write

Size: 8 bits

This register controls the CPU to AGP I/O access routing based on the following formula:

IO_BASE=< address =< IO_LIMI T

3.4.16 SSTS—Secondary PCI-to-PCI Status Register (Device 1)

Address Offset: 1 E–1Fh

Default Value: 02A0h

Access: Read Only, Read/Write Clear

Size: 16 bits

SSTS is a 16-bit status register that reports the occurrence of error conditions associated with

secondary side (i.e. AGP side) of the “virtual” PCI-to-PCI bridge embedded within 82443BX.

Bit Description

7:4 I/O Address Limit. Corresponds to A[15:12] of the I/O address. Default=0

3:0 Reserved. (Only 16 bit addressing supported.)

3-56

82443BX Host Bridge Datasheet

Bit Descriptions

Detected Parity Error (DPE1). Note that the PERRE1 bit does not affect the function of this bit.

Also the PERR# is not implemented in the 82443BX.

1 = 82443BX detected of a parity error in the address or data phase of AGP bus transactions.

0 = Software sets DPE1 to 0 by writing a 1 to this bit.

Received System Error (SSE1).

1 = 82443BX asserted SERR# for any enabled error condition under device 1. Device 1 error

conditions are enabled in the SSTS and BCTRL registers.

0 = Software clears SSE1 to 0 by writing a 1 to this bit.

13 Received Master Abort Status (RMAS1) .

1 = 82443BX terminates a Host-to-AGP with an unexpected master abort.

0 = Software resets this bit to 0 by writing a 1 to it.

12 Received Targe t Abort Status (RTAS1).

1 = 82443BX-initiated transaction on AG P is terminated with a target abort.

0 = Software resets RTAS1 to 0 by writing a 1 to it.

11 Signaled Target Abort Status (STAS1). STAS1 is hardwired to a 0, since the 82443BX does not

generate target abort on AG P.

10:9

DEVSEL# Timing (DEVT1). This 2-bit field indicates the timing of the DEVSEL# signal when the

82443BX responds as a target on AGP, and is hard-wired to the value 01b (medium) to indicate

the time when a valid DEVSEL# can be sampled by the initiator of the PCI cycle.

01 = Medium. (hardwired)

8Data P arity Detected (DPD1). Hardwired to 0. 82443BX does not implement G_PERR# function.

However, data parity errors are still detected and repor ted on SER R# (if enabled by SERRE,

SERRE1 and the BCTRL register, bit 0).

7Fast Back-t o-Back (FB2B1). This bit is hardwired to 1. The 82443BX as a target supports fast

back-to-back transactions on AG P.

6 Reserved.

566/60MHZ Capability. Hardwired to 1.

4:0 Reserved.

82443BX Host Bridge Datasheet

3-57

3.4.17 MBASE—Memory Base Address Register (Device 1)

Address Offset: 20–21h

Default Value: FFF0 h

Access: Read/Write

Size: 16 bits

This register controls the CPU to AGP non-prefetchable memory access routing based on the

following formula:

MEMORY_BA SE=< address =<MEMORY_LI MIT

This register must be initialized by the configuration software.

3.4.18 MLIMIT—Memory Limit Address Register (Device 1)

Address Offset: 22–23h

Default Value: 0000h

Access: Read/Write

Size: 16 bits

This register controls the CPU to AGP non-prefetchable memory access routing based on the

following formula:

MEMORY_BA SE=< address =<MEMORY_LI MIT

This register must be initialized by the configuration software.

Note: Memory range covered by MBASE and MLIMIT registers are used to map non-prefetchable AGP

address ranges (typically where control/status memory-mapped I/O data structures of the graphics

controller will reside) and PMBASE and PMLIMIT are used to map prefetchable address ranges

(typically graphics local memory). This segreg ation allo ws application of USWC space attribute to

be performed in a true plug-and-play manner to the prefetchable address range for improved CPU-

AGP memory access performance.

Note: The configuration software is responsible for programming all address range registers

(prefetchable, non-prefetchable) with the values that provide exclusive address ranges i.e. prevent

overlap with each other and/or with the ranges covered with the main memory. There is no

provision in the 82443BX hardware to enforce prevention of overlap and operations of the system

in the case of overlap are not guaranteed.

Bit Description

15: 4 Memory Address Base (MEM_BASE). Corresponds to A[31:20] of the memory address.

Default=FFF0h

3:0 Reserved.

Bit Description

15: 4 Memory Address Limit (MEM_LIMIT). Corresponds to A[31:20] of the memory address . Default=0

3:0 Reserved.

3-58

82443BX Host Bridge Datasheet

3.4.19 PMBASE—Prefetchable Memory Base Address Register

(Device 1)

Address Offset: 24–25h

Default Value: FFF 0h

Access: Read/Write

Size: 16 bits

This register controls the CPU to AGP prefetchable memory accesses routing based on the

following formula:

PREFET CHABLE_MEM ORY_B ASE=< address =<PREFE TCHABLE_ MEMORY_ LIMIT

This register must be initialized by the configuration software.

3.4.20 PMLIMIT—Prefetchabl e Memory Limit Address Register

(Device 1)

Address Offset: 26–27h

Default Value: 0000h

Access: Read/Write

Size: 16 bits

This register controls the CPU to AGP prefetchable memory accesses routing based on the

following formula:

PREFETC HABLE_MEM ORY _BASE =< address =<PRE FETCHAB LE_MEM ORY_LI MIT

This register must be initialized by the configuration software.

Note: The prefetchable memory range is supported to allow segregation by the configuration software

between the memory ranges that must be defined as Uncachable and the ones that can be

designated as a USWC (i.e. prefetchable) from the CPU perspective.

Bit Description

15: 4 Prefetchable Memory Address Base(PMEM_BASE).Corresponds to A[31:20] of the memor y

address.

Default=FFF0h

3:0 Reserved.

Bit Description

15: 4 Prefetchable Memory Address Limit (PMEM_LIMIT). Corresponds to A[31:20] of the memory

address. Default=0

3:0 Reserved.

82443BX Host Bridge Datasheet

3-59

3.4.21 BCT RL— PCI-to-PCI Bridg e Control Register (Device 1)

Address Offset: 3Eh

Default: 80h

Access: Read/Write

Size 8 bits

This register provides extensions to the PCICMD1 register that are specific to PCI-to-PCI bridges.

The BCTRL provides additional control for the secondary interface (i.e., A GP) as well as some bits

that affect the overall behavior of the “virtual” PCI-to-PCI bridge in the 82443BX (e.g., VGA

compatible address ranges mapping).

Bit Descriptions

7Fast Back to Back Enable. 82443BX supports fast back-to-back cycles on AGP, and therefore

this bit is hardwired to 1.

Secondary Bus Reset: 82443BX does not support generation of reset via this bit on the AGP

and therefore this bit is hardwired to 0.

NO TE: T he only w a y to perform a hard reset of the A GP is via the system reset either initi ated b y

software or hardware via PIIX4E.

5Master Abort Mode. Not applicable. Hardwired to 0. (This means when acting as a master on

AGP the 82443BX will drop writes on the “floor” and return all 1s during reads.)

4 Reserved.

VGA Enable. Controls the routing of CPU-initiated transactions targeting VGA compatible I/O

and memory address ranges.

1 = 82443BX will forward the following CPU accesses to AGP:

• memory accesses in the range 0A0000h to 0BFFFFh

• I/O addresses where A[9:0] are in the ranges 3B0h to 3BBh and 3C0h to 3DFh

(inclusive of ISA address aliases - A[15:10] are not decoded)

When this bit is set, forwarding of these accesses issued by the CPU is independent of the

I/O address and memory address ranges defined by the previously defined base and limit

registers. Forwarding of these accesses is also independent of the settings of bit 2 (ISA

Enable) of this register or of bit 5 (VGA Palette Snoop Enable) of the PCICMD1 register if

this bit is 1.

0 = VG A compa tible memory and I/O range accesses are mapped to PCI unless they are

redirected to AGP via I/O and memory range registers defined above (IOBASE, IOLIMIT,

MBASE, MLIMIT, PMBASE, PMLIMIT). (def ault )

ISA Enable. Modifies the response by the 82443BX to an I/O access issued by the CPU that

target ISA I/O addresses. This applies only to I/O addresses that are enabled by the IOBASE

and IOLIMIT registers.

1 = When this bit is set to 1 82443BX will not forward to AG P an y I/O transactions addressing

the last 768 bytes in each 1KB block even if the addresses are within the range defined by

the IOBASE and IOLIMIT registers. Instead going to AGP these cycles will be forwarded to

PCI where they can be subtractively or positively claimed by the ISA bridge.

0 = All addresses defined by the IOBASE and IOLIMIT for CPU I/O tr ansacti ons will be mapped

to AG P. (default)

1 Reserved.

Parity Error Response Enable. Controls 82443BX’s response to data phase parity errors on

A GP. G_PERR# is not implemented by the 82443BX. However, when this bit is set to 1, address

and data parity errors on AGP are reported via SERR# mechanism, if enabled by SERRE1 and

SERRE. If this bit is reset to 0, then address and data parity errors on AGP are not reported via

the 82443BX SERR# signal. Other types of error conditions can still be signaled via SERR#

independent of this bit’s state.

1 = Enable.

0 = Disable.

82443BX Host Bridge Datasheet

4-1

Function al Descr i pti on

Functional Description

This chapter describes the 82443BX interfaces on-chip functional units. Section 4.1, “System

Address Map” on page 4-1 provides a system-level address memory map and describes the

memory space contr ols pro vided b y the 824 43BX. This section also describes the I/O add ress map.

Note that 82443BX register maps are provided in Chapter 3, “Register Descriptio n” .

The 82443BX Host-to-PCI Bridge functions are described Host, PCI, and AGP interfaces are

described i n Section 4.2, “Host Interface” on pag e 4-10, Section 4.4, “PCI Interface ” on page 4-24,

and Section 4.5, “AGP Interface” on page 4-24.

The DRAM interf ace includi ng supporte d DRAM types, org anizations, co nfi gurations, an d regis ter

programming considerations is provided in Section 4.3, “DRAM Interface” on page 4-14. Data

integrity support on the Host bus, PCI bus, and DRAM interface is described in Section 4.6, “Data

Integrity Support” on page 4-25.

System clocking requirements is provided in Section 4.7, “System Clocking” on page 4-28.

The 82443BX has various power managem e nt capabilities. Suspend resume, clock control,

SDRAM power down, and SMRAM functions are described in Section 4.8, “Power Management”

on page 4-28. This section also contains information on the 82443BX reset operations.

4.1 System Address Map

A Pentium® Pro processor-based system with the Intel® 440BX AGPset supports 4 GB of

addressable memory space and 64 KB + 3 of addressable I/O space. (The Pentium® Pro processor

bus I/O addressability is 64 KB + 3). There is a programmable memory address sp ace und er the 1

MB region which is divided into regions which can be individually controlled with programmable

attributes such as Disable, Read/Write, Write Only, or Read On ly. Attribute programmin g is

described in the Register Description section. This section focuses on how the memory space is

partitioned and what these separate memory regions are used for. Th e I/O address sp ace requ ires

much simpler mapping and it is explained at the end of this section.

The Pentium Pro processor family supports addressing of memory ranges larger than 4 GB. The

82443BX Host Bridge claims any access o ver 4 GB by terminating transaction (without forwardin g

it to PCI or AGP). Writes are terminated simply by dropping the data and for reads the 82443BX

returns all zeros on the host bus. Note that the 82443BX as a target does not support the PCI Dual

Address Cycle Mechanism (DAC) which allows addressing of >4GB on either the PCI or AGP

interface.

In the following sections, it is assume d that all of the compatibility memory ranges reside on PCI.

The exception to this rule are the VGA ranges which may be mapped to AGP. In the absence of

more specific references, cycle descriptions referencing PCI should be interpreted as PCI, while

cycle descriptions referencing AGP are relate to AGP.

Functional Description

4-2

82443BX Host Bridge Datasheet

4.1.1 Memory Address Rang es

Figure 4-1 provides a detailed 82443BX memory map indicating specific memory regions defined

by AGP and supported by the In tel® 440BX AGPset.

Figure 4-1. Memory System Address Space

mem_map2.vsd

Notes:

1. Graphics Device accesses to the AGP aperture

invoke AGP transfer protocol on the AGP Bus

and use GART to re- map the accesses to

graphics data structures located in main

memory.

2. The two window regions provide PCI accesses

over the AGP. Main memory (physical memory) and

CPU extended memory (above 4 GB)

PCI memory accesses to primary PCI bus

AGP aperture, GART, and

Graphics data structures mapped by GART

PCI memory accesses to AGP

4 GB

System Memory Space

TOM (1 GB Max.)

Main

Memory

Local Graphics Memory

- Frame Buffer

- Rendering Buffer

- Depth Buffer (Z)

- Video Capture Buffer

Window For Prefetchable

PCI accesses to AGP

(Base=PMBASE Reg. (24h); Dev 1)

(Size=PMLIMIT Reg. (26h); Dev 1)

Graphics Address Re-Mapping Table

(Base=ATTBASE Reg. (B8h); Dev 0)

Window For Non-Prefetchable

PCI accesses to AGP

(Base=MBASE Reg. (20h); Dev 0)

(Size=MLIMIT Reg. (22h); Dev 0)

64 GB Extended CPU

Memory Space

PCI Memory

accesses to AGP

PCI Memory

accesses to AGP

PCI Memory

Graphics Device

Access

(e.g., memory-mapped

control/status registers)

GART

AGP

Aperture

PCI Memory

AGP Data

AGP Aperture

- Textures

- Other Surfaces

- Instruction

Stream

00000h

A0000h

BFFFFh

System/Application SW

Graphics Adapter

(128 KB)

C0000h Video BIOS

(shadowed in memory)

0FFFFFh

DOS

Compatibility

Memory

1 MB

Optional ISA Hole 15 MB

16 MB

Upper BIOS Area

(64 KB)

Lower BIOS Area

(64 KB)

16KBx4

Expansion Card BIOS

and Buffer Area

(128 KB) 16KBx8

Standard PCI/ISA Video

Memory (SMM Mem)

128 KB

Optional Fixed Memory

Hole

DOS Area

(512 KB)

000000h

080000h

07FFFFh

0A0000h

09FFFFh

0C0000h

0BFFFFh

0E0000h

0DFFFFh

0F0000h

0EFFFFh

0FFFFFh 1 MB

960 KB

896 KB

768 KB

640 KB

512 KB

0 KB

AGP Aperture Range

(Base=APBASE Reg. (10h); Dev 0)

(Size=APSIZE Reg. (B4h); Dev 0)

82443BX Host Bridge Datasheet

4-3

Function al Descr i pti on

4.1.1.1 Compatibility Area

This area is divided into the following address regions:

•0–512 KB DOS Area

•512 KB – 640 KB DOS Area - Optional ISA/PCI Memory

•640KB – 768 KB Video Buffer Area

•768 KB – 896 KB in 16KB sections (total of 8 sections) - Expansion Area

•896KB – 960 KB in 16KB sections (total of 4 sections) - Extended System BIOS Area

•960 KB – 1 MB Memory (BIOS Area) - System BIOS Area

There are sixteen memory segments in the compatibility area. Thirteen o f the memory ran ges can

be enabled or disabled independently for both read and write cycles . One segment

(512 KB–640 KB) which can be mapped to either main DRAM or PCI.

DOS Area (00000h–9FFFh)

The DOS area i s 640 KB and i t is further di v ided i nto tw o part s. T he 512 KB ar ea at 0 to 7F FFFh is

always mapped to the main memory controlled by the 82443BX, while the 128 KB address range

from 080000 to 09FFFFh can be mapped to PCI or to main DRAM. By default this range is

mapped to main memory and can be declared as a main memory hole (accesses forwarded to PCI)

via the 82443BX’s FDHC configuration register.

Video Buffer Area (A000 0h–B FFFFh)

The 128 KB graphics adapter memory region is normally mapped to a legacy video device on PCI

(typically VGA controller). This area is not controlled by attrib ute bits and CPU-initiated cycles in

this region are forwarded to PCI or AGP for termination. This region is also the default region for

SMM space.

The SMRAM Control register controls how SMM accesses to this space are treated.

Table 4-1. Memory Segments and their Attributes

Memory Segments Attribu tes Comments

000000h–07FFFFh fixed - always mapped to main DRAM 0 – 512 KB; DOS Region

080000h–09FFFFh configurable as PCI or main DRAM 512 KB – 640 KB; DOS Region

0A0000h–0BFFFFh mapped to PCI - configurable as SMM

space Video Buffer (physical DRAM

configurable as SMM space)

0C0000h–0C3FFFh WE; RE A dd-on BIOS

0C4000h–0C7FFFh WE; RE A dd-on BIOS

0C8000h–0CBFFFh WE ; RE Add-on BIOS

0CC000h–0CFFFFh WE; RE A dd-on BIOS

0D0000h–0D3FFFh WE; RE A dd-on BIOS

0D4000h–0D7FFFh WE; RE A dd-on BIOS

0D8000h–0DBFFFh WE ; RE Add-on BIOS

0DC000h–0DFFFFh WE; RE A dd-on BIOS

0E0000h–0E3FFFh WE; RE BIOS Extension

0E4000h–0E7FFFh WE; RE BIOS Extension

0E8000h–0EBFFFh WE; RE B IOS Extension

0EC000h–0EFFFFh WE ; RE BIOS Extension

0F0000h–0FFFFFh WE; RE BIOS Area

Functional Description

4-4

82443BX Host Bridge Datasheet

Monochrome Adapter (MDA) Range (B0000h–B7FFFh)

Legacy suppor t requires the ability to have a second graphics controller (monochro me) in the

system. In an AGP system, accesses in the normal V GA range are forw arded to the AGP bus. Since

the monochrome adapter may be on the PCI (or ISA) bus, the 82443BX must decode cycles in the

MDA range and forward them to PCI.

Expansion Area (C0000h–DFFFFh)

This 128 KB ISA Expansion region is divided into eight 16 KB segments. Each segment can be

assigned one of four Read/Write states: read-only, write-only, read/write, or disabled. Typically,

these blocks are mapped through the Host-to-PCI bridge and are subtractively decoded to ISA

space. Memory that is disabled is not remapped.

Extended System BIOS Area (E0000h–EFFFFh)

This 64 KB area is divided into four 16 KB segments. Each segment can be assigned independent

read and write attrib utes so it can be mapped either to m ain DRAM or to PCI. Typically, this area is

used for RAM or ROM. Memory segments that are disabled are not remapped elsewhere.

System BIOS Area (F0000h–FFFFFh)

This area is a single 64 KB segment. This segment can be assigned read and write attributes. It is by

default (after reset) Read/Write disabled and cycles are forwarded to PCI. By manipulating the

Read/Write attributes, the 82443BX can “sh a dow” BIOS into the main DRAM. When disabled,

this segment is n ot rem a pped.

4.1.1.2 Extended Memory Area

This memory area co ver s 10000 0h (1 MB) to FFFFFFF Fh (4 GB-1) address ran ge and it is di vi ded

into the following regions:

•Main DRAM Memory from 1 MB to the Top of Memory; maximum of 256 MB using 16M

DRAM technology or 1 GB using 6 4M technology

•PCI Memory space from the Top of Memory to 4 GB with two specific ranges:

— APIC Configuration Space from FEC0_0000h (4 GB-20 MB) to FECF_FFFFh and

EE0_0000h to FEEF_FFFFh

— High BIOS area from 4 GB to 4 GB – 2 MB

Main DRAM Address Range (0010_0000h to Top of Main Memory)

The address range from 1 MB to the top of main memory is mapped to main DRAM address range

controlled by the 82443BX. All accesses to addresses within this range will be forwarded by the

82443BX to th e DRAM unles s a h ole in this range is created using the fixed hole as controlled by

the FDHC register. Access es within this hole are forwarded to PCI.

The range of physical DRAM memory disabled by opening the hole is not remapped to the Top of

the Memory.

Extended SMRAM Address Range (Top of Main Memory – TSEG)

An extended SMRAM space of up to 1 MB can be defined in the address range at the top of

memory. The size of the SMRAM space is determined by the TSEG value in the ESMRAMC

82443BX Host Bridge Datasheet

4-5

Function al Descr i pti on

AGP accesses in this range are forwarded to PCI. When SMM is enabled the amount of memory

available to the system is equal to the amount of physical DRAM minus the value in the TSEG

Note: When ex tended SMRAM is used, the maxi mum amou nt of DRAM suppo rted is limited t o 256 MB.

PCI Memory Address Range (Top of Main Memory to 4 GB)

The address range from the top of main DRAM to 4 GB (top of physical memory space supported

by the Intel® 440BX AGPset) is normally mapped to PCI. There are two ex ceptions to this rule:

•Addresses decoded to the AGP Memory Window defined by the MBASE, MLIMIT,

PMBASE, and PMLIMIT registers are mapped to AGP.

•Addresses decoded to the Graphics Aperture range defined by the APBASE and APSIZE

registers are mapped to the main DRAM.

There are two sub-ranges within the PCI Memory address range defined as APIC Configuration

Space and High BIOS Address Range. The AGP Memory Windo w and Graphics Aperture W i ndow

MUST NOT overlap with these two ranges. These ranges are described in detail in the following

paragraphs.

APIC Configuration Space (FEC0_0000h -FECF_FFFFh, FEE0_0000h- FEEF_FFFFh)

This range is reserved for APIC configuration space which includes the default I/O APIC

configuration space. The default Local APIC configuration space is FEE0_0000h to FEEF_0FFFh.

CPU accesses to the Local APIC conf iguration space do not result in external b us acti vity since the

Local APIC conf igur ation space is internal to the CPU. Ho we v er, a MTRR must be programmed to

make the Local APIC range uncacheable (UC). The Local APIC base address in each CPU should

be relo cated to the F EC0_00 00h (4 GB – 20 MB) to F ECF_FF FFh ra nge so that on e MTRR can be

programmed to 64 KB for the Local and I/O APICs. The I/O APIC(s) usually reside in the I/O

Bridge portion of the AGPset or as a stand-alone compon ent(s). F or I ntel® 4 40BX AGPset syst ems

using the PIIX4E, the I/O APIC is supported as a stand-alone component residing on the X-Bus.

I/O APIC units will be located beginning at the defau lt address FEC0_0 000h. The first I/O APIC

will be located at FEC0_0000h. Each I/O APIC unit is located at FEC0_x000h where x is I/O APIC

unit number 0 throu gh F (hex). This addres s rang e will be normally mapped to PCI.

Note: There is no p rovisi on to suppo rt an I/O APIC de vice on AGP. Also the I/O APIC is not supported i n

a mobile platform.

The address range between the APIC configuration space and the High BIOS (FED0_0000h to

FEDF_FFFFh) is always mapped to the PCI.

High BIOS Area (FFE0_0000h –FFFF_FFFFh)

The top 2 MB of the Extended Memory Region is reserved for System BIOS (High BIOS),

ext ended B IOS for PCI devices, and th e A20 al ias of the sys tem BIOS. CPU be gins execution fro m

the High BIOS after reset. This region is mapped to PCI so that the upper subset of this region

aliases t o 16 MB–2 56 KB rang e. The actual address space required for the BIOS is less than 2 MB

but the minimum CPU MTRR range for this region is 2 MB so that full 2 MB must be considered.

The PIIX4E supports a maximum of 1 MB in the High BIOS range.

Functional Description

4-6

82443BX Host Bridge Datasheet

4.1.1.3 AGP Memor y Address Range

The 82443BX can be programmed to direct memory accesses to the AGP bus interface when

addresses are within either of two ranges specified via registers in 82443BX Device #1

configuration space. The first range is controlled via the Memory Base Register (MBASE) and

Memory Limit Register (MLIMIT) registers. The second range is controlled via the Prefetchable

Memory Base (PMBASE) and Prefetchable Memory Limit (PMLIMIT) registers

The 82443BX positively decodes memory accesses to AGP memory address space as defined by

the following equations:

Memor

_Base_Address ≤ Addr ess ≤ Memor

_Limit_Address

Prefetchable_Memor

_Base_Addr ess ≤ Addre ss ≤ Prefet chable_Memor

_Limit_Address

The effective size of the range is programmed by the plug-and-play configuration software and it

depends on the size of memory claimed by the AGP compliant device. Normally, these ranges

reside above the Top-of-Main-DRAM and below High BIOS and APIC address ranges.

Note: The 82443BX Device #1 memory range registers described above are used to allocate memory

address space for any devices on AGP that require such a window. These devices include the AGP

compliant device, and multifunctional AGP compliant devices where one or more functions are

implemented as PCI devices.

4.1.1.4 AGP DRAM Graphics Aperture

Memory-mapped, graphics data structures can reside in a Graphics Aperture to main DRAM

memory. This aperture is an address range defined by the APBASE configuration register of the

82443BX Host B ri dge. The AP BASE reg ist er f ol l ows the nor mal bas e addr ess regist er te mp la te as

defined b y the PCI 2.1 specif ication. Th e size of the range claimed b y the APB ASE is prog rammed

via “back-end” register APSIZE (programmed by the chip-set specific BIOS before plug-and-play

session is performed). APSIZE allows selection of the aperture size of 4 MB, 8 MB,16 MB,

32 MB, 64 MB, 128 MB and 256 MB. By programming APSIZE to a specific size, the

corresponding lower bits of APBASE are forced to “0” (behave as hardwired). Default value of

APSIZE forces aperture size of 256 MB. Aperture address range is naturally aligned.

Although this aperture appears to be established in PCI memory space, in fact the 82443BX

forwards accesses within the aperture range to the main DRAM subsystem. The originally issued

addresses are translated (within 82443BX’s DRAM controller subsystem) via a translation table

maintained in main memory. Translation table entries may be partially cached in a Graphics

Translation Look-aside Buffer (GTLB) implemented within the 82443BX’s DRAM subsystem.

The aperture range will not be cacheable in the processor caches.

4.1.1.5 System Management Mode (SMM) Memory Range

82443BX suppo rts the use of main memo ry as System Managemen t RAM (SMRAM) enabling the

use of System Management Mode. The 82443BX supports two SMRAM options: Compatible

SMRAM (C_SMRAM) and Extended SMRAM (E_SMRAM). System Management RAM

(SMRAM) space provides a memory area that is available for the SMI handler's and code and data

storage. This memory resource is normally hidden from the system OS so that the processor has

immediate access to this memory space upon entry to SMM. The 82443BX provides three

SMRAM op tions:

82443BX Host Bridge Datasheet

4-7

Function al Descr i pti on

•Below 1 MB option that suppo rt s compati b le SMI handlers.

•Above 1 MB option that allows new SMI handlers to execute with write-back cacheable

SMRAM.

•Optional larger write-back cacheable T_SEG area from 128KB to 1MB in size above 1 MB

that is reserved from the highest area in system DRAM memory. The above 1 MB solutions

require changes to compati b le SMR A M handle rs code to proper ly execute above 1 MB.

Table 4-2 summarizes the operation of SMRAM space cycles targeting the SMI space addresses.

NOTE:

1. 1 = Enabled and 0 = Disabled

Table 4-4 def i nes the contro l of the decod e fo r all co de fetches and d ata fetches to SMRAM ran ges

(as defined by Table 4-3). The G_SMRAM bit provides a global disable for all SMRAM memory.

The D_OPEN bit allows software to write to the SMRAM ranges without being in SMM. BIOS

software can use this bit to initialize SMM code at Power up. The D_LCK bit limits the SMRAM

range access to only SMM mode accesses. The D_CLS bit causes SMM data accesses to be

forwarded to PCI. The SMM software can use this bit to write to video memory while running code

out of DRAM.

NOTE:

1. 1 = Enabled and 0 = Disabled

Table 4-2. SMRAM Decoding

Name of Range Transaction Address DRAM Address

compatible (Range A) A 0000–B FFFFh A0000–BFFFFh

HI-SMRAM (RANGE H) 256M + A0000h to 256M + FFFFFh A0000–FFFFFh

TSEG (RANGE T) 256 M + TOM to 256M + TOM - TSEG_SIZE TOM to TOM - TSEG_SIZE

Table 4-3. SMRAM Range Decode

Global SMRAM H_SMRAME TSEG_EN A Range H Range T Range

0 x x Disable Disable Disable

1 0 0 Enable Disable Disable

1 0 1 Enable Disable Enable

1 1 0 Disabled Enable Disable

1 1 1 Disabled Enable Enable

Table 4-4. SMRAM Decode Control

G_SMRAME D_LCK D_CLS D_OPEN SMM Mode SMM Code

Fetch SMM Data

Fetch

0 xxxxDisableDisable

1 0 x 0 0 Disable Disable

1 0001EnableEnable

1 0 0 1 x Enable Enable

1 0101EnableDisable

1 0 1 1 x Invalid Invalid

1 1 x x 0 Disable Disable

1 1 0 x 1 Enable Enable

1 1 1 x 1 Enable Disable

Functional Description

4-8

82443BX Host Bridge Datasheet

Refer to Section 4.8, “Power Management” on page 4-28 for more details on SMRAM support.

Reiteration:

•Only un-cacheable SMM regions may overlap PCI or AGP Windows.

•SMM regions will not overlap the AGP aperture.

•Software (not in SMM) will not access PCI memory behind cacheable SMM regions.

•PCI or AGP masters cannot access the SMM space.

4.1.2 Memory Shadowing

Any block of memory that can be designated as read-only or write-only can be “shadowed” into

82443BX DRAM memory. Typically, this is done to allow ROM code to execute more rapidly out

of main DRAM. ROM is used as a read-only during the copy process while DRAM at the same

time is designated write-only. After copying, the DRAM is designated read-only so that ROM is

shadowed. CPU bus transactions are routed accordingly.

4.1.3 I/ O Address Space

The 82443BX does not support the existence of any other I/O devices besides itself on the CPU

bus. The 8244 3BX generates either PCI or A GP b us cycles for all CPU I/O accesses. The 82443BX

contains three internal registers in the CPU I/O space, Configuration Address Register

(CONFIG_ADDRESS) and the Configuration Data Register (CONFIG_DATA) and Power

Management Control Register. These locations are used to implement PCI configuration space

access mechanism and as described in Section 3.1, “I/O Mapped Registers” on page 3-2.

The CPU allows 64K+3 bytes to be addressed within the I/O space. The 82443BX propagates the

CPU I/O address without any translation on to th e destination bus and therefore provides

addressability for 64K+3 byte locations. Note that the upper 3 locations can be accessed only

during I/O address wrap-around when CPU bus A16# address signal is asserted. A16# is asserted

on the CPU bus whenever an I/O access is made to 4 bytes from address 0FFFDh, 0FFFEh, or

0FFFFh. A16# is also asserted when an I/O access is made to 2 bytes from address 0FFFFh.

The I/O accesses (other than ones used for PCI co nf iguration space access) ar e forw arded n ormally

to the PCI bus unless they fall within the PCI1/AGP I/O address range as defined by the

mechanisms in Section 4.1.4. The 82443BX will not post I/O write cycles to IDE.

4.1.4 AGP I/O Address Mapping

The 82443BX can be programmed to direct non-memory (I/O) accesses to the AGP bus interface

when CPU-initiated I/O cycle addresses are within the AG P I/O address range. This range is

controlled via the I/O Base Address (IOBASE) and I/O Limit Address (IOLIMIT) registers in

82443BX Device #1 configuration space.

The 82443BX positively decodes I/O accesses to AGP I/O address space as defined by the

following equation:

I/O_Base_Addr ess ≤ CPU I/O C

cle Address ≤ I/O_Limit_Address

The effective size of the range is programmed by the plug-and-play configuration software and it

depends on the size of I/O space claimed by the AGP compliant device.

82443BX Host Bridge Datasheet

4-9

Function al Descr i pti on

Note that the 82443BX Device #1 I/O address range registers defined above are used for all I/O

space allocation for an y d e vices requirin g such a windo w on AGP. These devices w ould inclu de the

AG P compliant device and multifunctional AGP compliant devices where one or more functions

are implemented as PCI devices.

4.1.5 Decode Rules and Cross-Bridge Addre ss Mapping

The address map described above applies globally to accesses arriving on any of the three

interfaces (i.e., Host bus, PCI or AGP).

4.1.5.1 PCI Interface Decode Rules

The 82443BX accepts accesses from PCI to the following address ranges:

•All memory read and write accesses to Main DRAM

•Memory Write accesses to AGP memory range defined by MBASE, MLIMIT, PMBASE, and

PMLIMIT. 82443BX will not respond to memory read accesses to this range.

•Memory read/write accesses to the Graphics Aperture defined by APBASE and APSIZE.

PCI accesses that fall elsewhere within the PCI memory rang e will not be accepted. PCI cycles not

explicitly claimed by the 82443BX are either subtractively decoded or master-aborted on PCI.

4.1.5.2 AGP Interface Decode Rules

Cycles Initiated Using PCI Protocol

Accesses between A GP and PCI are limited to memory writes using the PCI proto col. Write cycles

are forwarded to PCI if the addresses are not within main DRAM range, AGP memory ranges, or

Graphics Aperture range.

The 82443BX will claim AGP initiated memory read transactions decod e d to the main DRAM

range or the Graphics Aperture range. All other memory read requests will be master-aborted by

the AGP initiator as a consequence of 82443BX not responding to a transaction.

If agent on AGP issues an I/O, PCI Configuration or PCI Special Cycle transaction, the 82443BX

will not respond and cycle will result in a mast er-abort.

Cycles Initiated Using AGP Protoco l

All cycles must reference main memory (i.e., main DRAM address range or Graphics Aperture

range which is also physically mapped within DRAM but using different address range).

AGP-initiated cycles that target DRAM are not snooped on the host bus, ev en if they fall outside of

the AGP aperture range.

If cycle is outside of main memory range then it will terminate as follows:

•Reads: return random value

•Writes: dropped “on the floor” i.e. terminated internally without affecting any buffers or main

memory

•ECC errors that occur on reads outside of DRAM are not reported or scrubbed.

Functional Description

4-10

82443BX Host Bridge Datasheet

4.1. 5.3 Legacy VGA Ranges

The leg acy VGA memory rang e A0000h– BFFFFh is mapped either to PCI or to A GP depen ding on

the programming of the B CTRL conf igu ration re gister in 82 443BX Device #1 conf iguration space,

and the NBXCONF (MDAP bit) conf igur ation re gister in Device #0 conf igur ation space. The same

registers control mapping of VGA I/O address ranges. VGA I/O range is defined as addresses

where A[9:0] are in th e ranges 3B0h to 3BBh and 3C0h to 3 DFh (inclusi v e of ISA add ress aliases -

A[15:10] are not decoded).

4.2 H ost Interface

The host interface of the 8 244 3BX is optimized to sup por t the Pentium I I pr ocessor with bus clock

frequencies of 100 MHz and 66/60 MHz. The 82443BX implements the host address, control, and

data bus interfaces within a single device. Host bus addresses are decoded by the 82443BX for

accesses to main memory, PCI memory, PCI I/O, PCI configuration space and AGP space

(memory, I/O and configuration). The 82443BX takes advantage of the pipelined addressing

capability of the Pentium II processor to improve the overall system performan ce.

4.2.1 Host Bus Device Support

The 82443BX recognizes and supports a large subset of the transaction types that are defined for

the Pentium Pro processor b us interface. Howe v er, each of these transaction types have a multitude

of response types, some of which are not supported by this controller. All transactions are

processed in the order that they are received on the Pentium® Pro processor bus. Table 4-5

summarizes the transactions supported by the 82443BX.

Topic Definition

AGP IO

range

The A GP b us can be allocated with 1 bloc k of IO space with a granularity of 4KB. The IO base

address register points to the beginning of the AGP IO range while IO limit address register

points to the end of this range. The IO range definition is based on the PCI to PCI specification.

ISA_EN

The ISA_EN bit in the 82443BX device1 is necessary in ISA bus based systems where there is

a need to allocate IO space to AGP bus devices. This is necessary since legacy ISA devices

decode IO range of address [9:0] only and thus the IO address of the dev ices are aliased for

every 1 KB of the 64 KB IO range. Therefore, to provide IO range to AG P bus and maintain the

ISA IO legacy rules, the ISA_EN is set. As a result, all CPU cycles in the address ranges:

“xxxx_xx01_0000_0000”b to “xxxx_xx11_1111_1111”b, that is the top 768 bytes of each 1KB

aligned bloc k, are sent to the PCI bus independent of whether thi s particular address is inside or

outside the range allocated to the AGP bus.

The abov e is relevant only to CPU-initiated cycles, as PCI and AGP master IO cycles are never

claimed by the 82443BX. The ISA_EN functional definition is based on the PCI to PCI

specification.

VGA_EN

VGA IO range is defined in the following r anges: 3B0-3BBh, 3C0-3DFh. When the VGA_EN is

set, all CPU initiated IO cycles in the VGA IO range are forwarded to the AGP bus, independent

of whether the ISA_EN bit is set or not. Thus the VGA_EN bit setting tak es precedence relative

to the setting of the ISA_EN bit. The VGA_EN functional definition is based on the PCI to PCI

specification.

MDAP

The MD A IO range includes the ports 3B4h, 3B5h, 3B8h, 3B9h, 3BAh, 3BFh. Once the V GA_EN

is set, it is legal to set the MDAP bit to indicate that a second CRT controller (Monoch rome

Display Adapter) resides in the PCI or ISA b us . In t his case, all the CPU-initiated IO cycles in the

VGA range that are not in to the above ports are sent to AGP bus while the cycles to the above

six IO ports (and to all the aliased ports) are sent to PCI bus.

Note that the CPU IO cycles to the above ports are sent to AGP bus independent of the AGP IO

range and ISA_EN setting.

82443BX Host Bridge Datasheet

4-11

Function al Descr i pti on

NOTE:

1. For Memory cycles, REQa[4:3]# = ASZ#. The 82443BX only supports ASZ# = 00 (32 bit address).

2. REQb[4:3]# = DSZ#. For the Pentium® Pro processor, DSZ# = 00 (64 bit data b us size).

3. LEN# = data transfer length as follows:

LEN# Data length

00 ≤ 8 bytes (BE[7:0]# specify granularity)

01 Length = 16 bytes BE[7:0]# all active

10 Length = 32 bytes BE[7:0]# all active

11 Reserved

Table 4-5. Host Bus Transactions Supported By 82443BX

Transaction REQA[4:0]# REQB[4:0]# 82443BX Suppor t

Deferred Reply 0 0 0 0 0 X X X X X The 82443BX initiates a deferred reply for a

previously deferred transaction.

Reserved 0 0 0 0 1 X X X X X Reserved

Interrupt Acknowledge 0 1 0 0 0 0 0 0 0 0 Interrupt ackno wledge cycles are f orwarded to

the PCI bus.

Special Transactions 0 1 0 0 0 0 0 0 0 1 See separate table in Special Cycles section.

Reser ved 0 1 0 0 0 0 0 0 1 x Reserved

Reserved 0 1 0 0 0 0 0 1 x x Reserved

Branch Trace Message 0 1 0 0 1 0 0 0 0 0 The 82443BX ter m inates a branch trace

message without latching data.

Reser ved 0 1 0 0 1 0 0 0 0 1 Reser ved

Reser ved 0 1 0 0 1 0 0 0 1 x Reserved

Reserved 0 1 0 0 1 0 0 1 x x Reserved

I/O Read 1 0 0 0 0 0 0 x LEN# I/O read cycles are forwarded to PCI or AGP.

I/O cycles which are in the 82443BX

configuration space are not forwarded to PCI.

I/O Write 1 0 0 0 1 0 0 x LEN# I/O write cycles are forwarded to PCI or AGP.

I/O cycles which are in the 82443BX

configuration space are not forwarded to PCI.

Reserved 1 1 0 0 x 0 0 x x x Reserved

Memory Read &

Invalidate 0 0 0 1 0 0 0 x LEN#

Host initiated memory read cycles are

forwarded to DRAM or the PCI/1 bus. The

82443BX initiates an MRI cycle for a PCI/1

initiated write cycle to DRAM.

Reserved 0 0 0 1 1 0 0 x LEN# Reserved

Memory Code Read 0 0 1 0 0 0 0 x LEN# Memo ry code read cycles are forwarded to

DRAM or PCI/1 .

Memory Data Read 0 0 1 1 0 0 0 x LEN#

Host initiated memory read cycles are

forwarded to DRAM or the PCI/1 bus. The

82443BX initiates a memory read cycle for a

PCI/1 initiated read cycle to DRAM.

Memory Write (no retry) 0 0 1 0 1 0 0 x LEN# This memor y write is a writeback cycle and

cannot be retried. The 82443BX forwards the

write to DRAM.

Memory Write (can be

retried) 0 0 1 1 1 0 0 x LEN# The normal memory write cycle is forwarded

to DRAM or PCI/1.

Functional Description

4-12

82443BX Host Bridge Datasheet

Special Cycles

A Special Cycle is defined when REQa[4:0] = 01000 and REQb[4:0]= xx001. The first address

phase Aa[35:3] # is undef ined and can be driven to an y v a lue. The s econd ad dress phase, Ab[15:8]#

defines the type of Special Cycle issued by the processor.

Table 4-3 specifies the cycle type and definition as well as the action taken by the 82443BX when

the corresponding cycles are identified.

Table 4-6. Host Responses supported by the 82443BX

RS2# RS1# RS0# Description 82443BX Support

000idle

0 0 1 Retry Respons e

To a v oi d deadloc k, this response is generated when a

resource cannot currently be accessed by the

processor. PCI-directed reads, writes, DRAM locked

reads, AGP reads and writes can be retried.

0 1 0 Deferred Response

This response can be returned for al l transactions that

can be executed ‘out of order.’ PCI-directed reads

(memory, I/O and Interrupt Acknowledge) and writes

(I/O only), and AGP directed reads (memory and I/O)

and writes (I/O only) can be deferred.

0 1 1 Reserved Reserved

1 0 0 Hard Failure Not supported.

1 0 1 No Data Response

This is for transactions where the data has already

been transferred or for tr ansactions where no data is

transferred. Writes and zero length reads receiv e this

response.

1 1 0 Implicit Writeback This response is given for those transactions where

the initial transactions snoop hits on a modified cache

line.

111

Norm al Data

Response

This response is for transactions where data

accompanies the response phase. Reads receive this

response.

Table 4-7. Host Special Cycles with 82443BX

BE[7:0}# Special

Cycle Type Action Taken

0000

0000 NOP This transaction has no side-effects.

0000

0001 Shutdown

This transaction is issued when an agent detects a severe software error that

prevents further processing. This cycle is claimed by the 82443BX. T he 82443BX

issues a shutdown special cycle on the PCI bus. This cycle is retired on the CPU

bus after it is terminated on the PCI via a master abort mechanism.

0000

0010 Flush This transaction is issued when an agent has invalidated its internal caches

without writing back any modified lines. The 82443BX claims this cycle and

retires it.

0000

0011 Halt

This transaction is issued when an agent executes a HLT instru ction and stops

program execution. This cycle is claimed by the 82443BX and propagated to PCI

as a Special Halt Cycle . This cycle is retired on the CPU bus after it is terminated

on the PCI via a master abort mechanism.

0000

0100 Sync This transaction is issued when an agent has written back all modified lines and

has invalidated its inter nal caches. The 82443BX claims this cycle and retires it.

82443BX Host Bridge Datasheet

4-13

Function al Descr i pti on

NOTE:

1. None of the host bus special cycles is propagated to the AG P interface.

4.2.2 Symmetric Multiprocessor (SMP) Protocol Support

The Intel® 440BX A GPset is optimized for uniprocessor system and also supports the symmetrical

multiprocessor configurations of up to two CPUs on the host bus.

When configured for dual-processor, the Intel® 440BX AGP set-based platform must integrate an

I/O APIC functionality and WSC# signaling mechanis m must be enabled.

4.2.3 In-Order Queue Pipelining

The 82443BX interface to the CPU bus includes a four deep in-order queue to track pipelined bus

transactions.

4.2.4 Frame Buffer Memory Support (USWC)

To allow for high speed write capability for graphics, the Pentium Pro processor family has

introduced USWC memory ty pe. The USWC (uncacheable, speculati ve, write-comb ining) memory

type provides a write-combining buffering mechanism for write operations. A high percentage of

graphics transactions are writes to the memory-mapped graphics region, normally known as the

linear frame buffer. Reads and writes to USWC are non-cached and can have no side effects .

In the case of graphics, current 32-bit drivers (without modifications) would use Partial Write

protocol to update the frame buffer. The highest performance write transaction on the CPU bus is

the Line Write.

0000

0101 Flush

Acknowledge

This transaction is issued when an agent has completed a cache sync and flush

operation in response to an earlier FLUSH# signal asser tion. The 82443BX

claims this cycle and retires it.

0000

0110 Stop Clock

Acknowledge

This transaction is issued when an agent enters Stop Clock mode. This cycle is

claimed by the 82443BX and propagated to the PCI as a Special Stop Grant

Cycle. This cycle is completed on the CPU bus after it is terminated on the PCI

via a master abort mechanism.

0000

0111 SMI

Acknowledge T his transaction is first issued when an agent enters the System Management

Mode (SMM).

all others Reser ved

Table 4-7. Host Special Cycles with 82443BX

BE[7:0}# Special

Cycle Type Action Taken

Functional Description

4-14

82443BX Host Bridge Datasheet

4.3 DRAM Interface

The 82443BX integrates a main memory DRAM controller that supports a 64-bit or 72-bit (64-bit

memory data plus 8 ECC) DRAM array. The DRAM types supported are Synchronous (SDRAM)

and Extended Data Out (EDO). The 82443BX does not support mixing of SDRAM and EDO.

When the CPU bus is running at 100 MHz, the 82443BX DRAM interface runs at 100 MHz

(SDRAM only). When the CPU b us is operating at 66 MHz, the 824 43BX DRAM interf ace runs at

66 MHz (SDRAM or EDO). EDO DRAM technology is supported in mobile designs only at 66

MHz. The DRAM controller interface is fully configurable through a set of control registers.

Complete descrip tions of these registers are given in the Register Section. A brief overview of the

registers which configure the DRAM interface is provided in this section.

The 82443BX supports industry standard 64/72-bit wide DIMM modules with SDRAM and EDO

DRAM devices. The fourteen multiple xed address lines, MA[13:0], allow the 82443BX to support

1M, 2M, 4M, 8M, and 16M x72/64 DIMMs. Both symmetric and asymmetric addressing is

supported. The 82443BX has sixteen CS# lines, used in pairs enabling the support of up to eight

64/72-bi t rows of DRAM. For write operations of less than a QWord in size, the 82443BX will

either perform a byte-wise write (non-ECC protected configuration) or a read-modify-write cy cle

by merging the write data on a byte basis with the previously read data (ECC or EC configurations).

The 82443BX targets 60 ns EDO DRAMs and SDRAM with CL2 and CL3 and supports both

single and double-si ded DIMMs. Wh en using EDO DRAM, up t o 6 ro ws of memo ry are supp orted.

The 82443BX provides refresh functionality with pr ogrammable rate (normal DRAM rate is 1

refresh/15.6ms). When using SDRAMs the 82443BX can be configured via the Paging Policy

of memory. When 4 bank SDRAM devices (64Mb technology) are used for a particular row, up to

4 pages can be kept open within that row.

The DRAM interface of the 82443BX is configured by the DRAM Control Register, DRAM

Timing Register, SDRAM Control Register, bits in the NBXCFG and the eight DRAM Row

Boundary (DRB) Registers. The DRAM configuration registers noted above control the DRAM

interface to select EDO or SDRAM DRAMs, RAS timings, and CAS rates. The eight DRB

Registers define the size of each row in the memory array, enabling the 82443BX to assert the

proper CSA/B# pair for accesses to the array.

4.3.1 DRAM Organization and Configuration

The 82443BX supp orts 64/72-bit DRAM configurations . In the following discu ssion the term row

refers to a set of memory devices that are simultaneously selected by a CSA/B# or RASA/B# pair.

The 82443BX will support a maximum of 8 rows of memory when using SDRAMs in a desktop

configuration. Up to 6 rows of memory are supported when using EDO DRAM. A row may be

composed of discrete DRAM devices, single-sided or double-sided DIMMs.

The 82443BX has multiple copies of many of the signals interfacing to memory. The interface

consists of the following pins.

•Multiple copies

— MAA[13:0], MAB[12:11,9:0]# and MAB[13,10]

— CSA[7:0]#, CSB[7:0]#

—SRASA#, SRASB#

—SCASA#, SCASB#

— WEA#, WEB#

— DQMA[7:0], DQMB[5,1]

— CKE[5:0] (for 3 DIMM configuration)

82443BX Host Bridge Datasheet

4-15

Function al Descr i pti on

•Single Copy

—MD[63:0]

— MECC[7:0]

— GCKE (for 4 DIMM configuration)

— FENA (FET switch control for 4 DIMM configuration)

The CS# pins function as RAS# pins in the case of EDO DRAMs. The DQM pins function as

CAS# pins in the case of EDO DRAMs. Two CS# lines are provided per row. These are

functionally equivalent. The extra copy is provided for loading reasons. The two SRAS#’s,

SCAS#’s and WE#’s are also functionally equivalent and each copy drives two rows of DRAM.

Most pins utilize programmable strength output buffers (refer to Register Section). When a row

contains 16Mb SDRAMs, MAA11 and MAB11 function as Bank Select lines. When a row

contains 64Mb SDRAMs, MAA/B[12:11] function as Bank Addresses (BA[1:0], or Bank Selects).

The entire memory array may be conf igured as either normal SDRAM, re gistered SDRAM or EDO

DRAM . Mixing DRAM t ypes within one system is not supported. DIMMs may be populated in

any order. That is, any combination of rows may be populated. Registered SDRAM DIMMs allow

for support of x4 SDRAM components.

Table 4-8 illustrates a sample of the pos sib le DIMM socket configurations along with

corresp on di ng DRB pro gramming.

NOTE:

1. "S" denotes single-sided DIMM's, "D" denotes double-sided DIMM's.

Figure 4-2 depicts the 82443BX connections for an SDRAM memory array and shows how the

copies of the signals are distributed to the array. If cross bar switches are used, the unused input

must be pulled down through a resistor. In an EDO memory array, the CSA/B[5:0]# signals would

be RASA/B[5:0]# lines and the DQMA/B[7:0] signals would be CASA/B[7:0]# lines. GCKE

requires external logic (not shown). For a 3 DIMM solution, separate CKE lines are provided for

each ro w (CKE[5:0]) .

Table 4-8. Sample Of Possible Mix And Match Options For 6 Row/3 DIMM Configurations

DIMM0\ DIMM1 DIMM2 DRB

0DRB

1DRB

2DRB

3DRB

4DRB

5DRB

6DRB

7Total

Memory

0 0 1MB x 72/S 00h 00h 00h 00h 01h 01h 01h 01h 8 MB

1MBx72/S 0 0 01h 01h 01h 01h 01h 0 1h 01h 01h 8 MB

2MBx72/S 0 0 02h 02h 02h 02h 02h 02h 02h 02h 16 MB

1Mx72/S 1Mx72/S 0 01h 01h 02h 02h 02h 02h 02h 02h 16 MB

0 4Mx72/S 0 00h 00h 04h 04h 04h 04h 04h 04h 32 MB

2Mx72/D 2Mx72/D 2Mx72/D 01h 02h 03h 04h 05h 06h 06h 06h 48 MB

4Mx72/S 0 2Mx72/D 04h 04h 04h 04h 05h 06h 06h 06h 48 MB

4Mx72/S 0 4Mx72/S 04h 04h 04h 04h 08h 08h 08h 08h 64 MB

4Mx72/S 4Mx72/S 2M x72/D 04h 04h 08h 08h 09h 1 0h 10h 10h 80 MB

8Mx72/D 0 4Mx72/S 04h 08h 08h 08h 0Ch 0Ch 0Ch 0Ch 96 MB

8Mx72/D 8Mx72/D 8Mx72/D 04h 08h 0Ch 10h 14h 1 8h 18h 18h 192 MB

16Mx72/S 16Mx72/S 0 10h 10h 20 h 20h 20h 20h 20h 20h 256 MB

8Mx72/D 16Mx72/S 8Mx72/D 04h 08h 18h 18h 1Ch 20h 20h 20h 256 MB

0 32Mx72/D 16Mx72/S 00h 00h 10h 20h 30h 30h 30h 30h 384 MB

32Mx72/D 32Mx72/D 16Mx72/S 10h 20h 30h 40h 50h 50h 50h 50h 640 MB

Functional Description

4-16

82443BX Host Bridge Datasheet

Figure 4-2. Four-DIMM Configuration with FET switches

CSA[7:6]#, CSB[7:6]#

CSA[5:4]#, CSB[5:4]#

CSA[3:2]#, CSB[3:2]#

CSA[1:0]#, CSB[1:0]#

SRASA#

SRASB#

SCASA#

SCASB#

DQMA[1,5]

DQMA[7,6,4:2,0]

DQMB[1,5]

WEA#

WEB#

GCKE

MAA[13:0]

MAB[13:11#, 10, 9:0#]

MD[63:0]

FENA

MECC[7:0]

DIMM_CLK[3:0]

DIMM_CLK[7:4]

DIMM_CLK[11:8]

DIMM_CLK[15:12]

SMB_CLK

SMB_DATA

Mux

Shift

Group 0

RGCKE[7:0]#

Group 1

82443BX Host Bridge Datasheet

4-17

Function al Descr i pti on

Figure 4-3. Three-DIMM SDRAM Configuration

CSA[5:4]#, CSB[5:4]#

CSA[3:2]#, CSB[3:2]#

CSA[1:0]#, CSB[1:0]#

SRASA#

SRASB#

SCASA#

SCASB#

DQMA[1,5]

DQMA[7,6,4:2,0]

DQMB[1,5]

WEA#

WEB#

MAA[13:0]

MAB[13:11#, 10, 9:0#]

MD[63:0]

MECC[7:0]

DIMM_CLK[3:0]

DIMM_CLK[7:4]

DIMM_CLK[11:8]

CKE[1:0]

CKE[3:2]

CKE[5:4]

SMB_CLK

SMB_DATA

S0/S1,S2/S3

/RAS

/CAS

DQM

DQ[63:0]

CB[7:0]

CK[3:0]

CKE

SCL

SDA

Functional Description

4-18

82443BX Host Bridge Datasheet

Figure 4-4. Three-SODIMMs EDO Configuration

RASA[1:0]#

RASA[3:2]#

RASA[5:4]#

MAB[13:11#, 10, 9:0#]

CASA[7:0]#

WEA#

MD[63:0]

MECC[7:0]

SRAS[B:A]]

SCAS[B:A]

CKE0/FENA

CKE[5:1]

WE_B#

CASB[5:1]/DQMB[5:1]#

MAA[13:0]

RASB[5:0]/CS_B[5:0]#

Note 1

Note 2

NOTE:

1. These signals are not connected in an EDO configuration.

2. These signals are not used and should be left unconnected.

SODIMM2 SODIMM1 SODIMM0

82443BX

82443BX Host Bridge Datasheet

4-19

Function al Descr i pti on

4.3.1.1 Configuration Mechanism For DIMMS

Detection of the type of DRAM installed on the DIMM is supported via Serial Presence Detect

mechanism as defined in the JEDEC 168-pin DIMM standard. This standard uses the SCL, SDA

and SA[2:0] pins on the DIMMs to detect the type and size of the installed DIMMs. No special

programmable modes are provided on the 82443BX for detecting the size and type of memory

installed. Type and size detection must be done via the serial presence detection pins.

Memory Detection and Initialization

Before any cycles to the memory interface can be supported, the 82443BX DRAM registers must

be initialized. The 824 43BX must be configured for operation with the installed memory types.

Detection of memory type and size is done via the System Management Bus (SMB) interface on

the PIIX4E. This two wire bus is used to extract the DRAM type and size information from the

serial presence detect port on the DRAM DIMMs.

DRAM DIMMs contain a 5 pin ser ial presence detect interface, includin g SCL (serial clock ), SDA

(serial data) and SA[2:0]. Devices on the SMBus bus have a seven bit address. For the DRAM

DIMMs, the upper four bits are fixed at 1010. The lower three bits are strapped on the SA[2:0]

pins. SCL and SDA are connected directly to the System Management Bus on the PIIX4E. Thus

data is read from the Serial Presence Detect port on the DIMMs via a series of IO cycles to the

south bridge. BIOS essentially needs to determine th e size and typ e of memory used fo r each o f the

eight rows of memory in order to properly configure the 82443BX memory interface.

Figure 4-5. Three-SODIMMs SDRAM Configuration

Note 1

SODIMM2 SODIMM1 SODIMM0

CSA[1:0]#

CSA[3:2]#

CSA[5:4]#

SRASA#

SCASA#

DQMA[7:0]#

WEA#

MAB[13:11#, 10, 9:0#]

MD[63:0]

MECC[7:0]

CKE[1:0]

CKE[3:2]

CKE[5:4]

SRASB#

SCASB#

WE_B#

CASB[5,1]/DQMB[5:1]#

MAA[13:0]

RASB[5:0]/CS_B[5:0]#

NOTE:

1. These signals are not used and should be left unconnected.

82443BX

Functional Description

4-20

82443BX Host Bridge Datasheet

DRAM Register Programming

The Serial Presence Detect p orts are used to determine Refresh Rate, MA and MD Buf f er Strength,

Row Type (on a row by row basis), EDO Timings, SDRAM Timings, Row Sizes and Row Page

Sizes. Table 4-9 list s a subset of the data available through the on board Serial Presence Detect

ROM on each DIMM.

Table 4-9 is only a subset of the defined SPD bytes on the DIMMs. For example, to program the

DRB (DRAM Row Boundary) registers, the size of each row must be determined. The number of

row addresses (byte 3) plus the number of column addresses (byte 4) plus the number of banks on

each SDRAM dev ice (byte 17) collecti v ely determines the total address depth of a particular ro w of

SDRAM . Since a row is always 64 data bits wide, the size of the row is easily determined for

programming the DRB registers.

The 82443BX uses the DRAM Row Type information in conjunctio n with the DRAM timings set

in the DRAM Timing Register to configure DRAM accesses optimally.

4.3.2 DRAM Address Translation and Decoding

The 82443BX s upp ort s 16 and 6 4 Mbi t DRAM devices. The 82 443 BX s upp ort s a 2 KB, 4 KB an d

8 KB page sizes (for SDRAM only). Page size varies per row depending on how many column

address lines are used for a gi v en row. Rows containing SDRAMs with 8 column lines ha v e a 2 KB

page size. Those with 9 column lin es hav e a 4 KB page size and those with 10 column address lines

have an 8 KB page size. In systems with EDO memory, a fixed 2 KB page size is used. The

multiplexed ro w/column address to the DRAM memory array is provided by the MA[13:0] signals.

Row and Column address multi pl exing on the MA[13:0] lines is det erm in ed on a row by row basis

allowing for three possible page sizes. SDRAMs have either 8, 9 or 10 column lines allowing for

2 KB, 4 KB or 8 KB page si zes. The 8 2443BX sup por ts only a 2 KB page size with EDO DRAMs.

The page size is determined primarily by the row size and type (SDRAM).

When EDO DRAM is used, the 82443BX will open at most one page at a time. That is, one RAS#

line will be asserted at any time. When SDRAM is used, either 2 or 4 pages can be open at any time

within any row. If a row contains SDRAMs based on 16Mb technology (i.e., 12x8/9/10 devices)

then two pages can be open at a time within that row. If a row contains SDRAMs based on 64Mb

technology, (i.e., 14x8/9/10 devices) then four pages can be open at a time within that row.

Table 4-9. Data Bytes on DIMM Used for Programming DRAM Registers

Byte Function

2 Memory Type (EDO, SDRAM)

3 # of Row Addresses, not counting Bank Addresses

4 # of Column Addresses

5 # of banks of DRAM (Single or Double sided) DIMM

11 ECC, no ECC

12 Refresh Rate

17 # Banks on each SDRAM Device

36-41 Access Time from Clock for CAS# La tency 1 through 7

42 Data Width of SDRAM Components

82443BX Host Bridge Datasheet

4-21

Function al Descr i pti on

This address multiplexing scheme is derived from Table 4-11 which depicts the addressing

requirements for each of the row/column organizations for each row size. The SDRAM

components used for the options shown in the table are as follows:

Note: Both 4Mx4 and 16Mx4 SDRAM devices are supported in the form of Registered DIMMs only.

Option SDRAM Component Type

2 (16MB) 2Mx8

3 (32MB) 4Mx16 or 4Mx4 (Registered DIMM only)

4 (64MB) 8Mx8

5 (128MB) 16Mx4 (Registered DIMM only)

Table 4-10. Supported Memory Configurations

DRAM Attributes DRAM DIMM DRAM

Addressing MA DRAM

Size

Type Tech Depth Width SS x64 DS x64 Ro w Col Banks Min

(1 row)

EDO 4M 1M 4 1M 2M Symmetric 10 10 NA 8 MB

1M 4 1 M 2M Asymm etri c 11 9 NA 8 MB

EDO 16M 2M 8 2M 4M Asymm etri c 11 10 NA 16 MB

2M 8 2 M 4M Asymm etri c 12 9 NA 16 MB

2M 8 2 M 4M Asymm etri c 13 8 NA 16 MB

4M 4 4M 8M Symmetr ic 11 11 NA 32 MB

4M 4 4 M 8M Asymm etri c 12 10 NA 32 MB

4M 4 4 M 8M Asymm etri c 14 8 NA 32 MB

EDO 64M 4M 16 4M 8M S ym metric 11 11 NA 32 MB

4M 16 4M 8M A sy mmetric 12 10 NA 32 MB

4M 16 4M 8M Asymmetric 14 8 NA 32 MB

8M 8 8M 16M Asymmetric 12 11 NA 64 MB

16M 4 16M 32M Symmetric 12 12 NA 128 MB

SDRAM 16M 2M 8 2M 4M Asy mm etr ic 12 9 2 16 MB

2M 8 2 M 4M Asymm etri c 13 8 2 16 MB

4M 4 4 M 8M Asymm etri c 12 10 2 32 MB

4M 4 4 M 8M Asymm etri c 14 8 2 32 MB

SDRAM 64M 4M 16 4M 8M Asy mm etric 14 8 4 32 MB

4 bank 8M 8 8M 16M Asymmetric 14 9 4 64 MB

16M 4 16M 32M Asy mmetric 14 10 4 128 MB

Functional Description

4-22

82443BX Host Bridge Datasheet

NOTE:

1. * Indicates SDRAM organization

Table 4-11. MA Muxing vs. DRAM Address Split

Split Row/

Col SDRAM

A11 BA1 BA0 A10/

AP A9 A8 A7 A6 A5 A4 A3 A2 A1 A0

Option 1 12x8* Row 11 12 14 13 22 21 20 19 18 17 16 15

8 MB Col 11AP 109876543

11x9 Row 12 14132221201918171615

Col 11109876543

10x10 Row 14132221201918171615

Col 1211109876543

12x8 Row 11 12 14132221201918171615

Col 109876543

Option 2 12x9* Row 12 23 14132221201918171615

16 MB Col 12AP 11109876543

13x8* Row 12 11 23 14132221201918171615

Col 1211AP 109876543

11x10 Row 23 14132221201918171615

Col 1211109876543

12x9 Row 12 23 14132221201918171615

Col 11109876543

13x8 Row 11 12 23 14132221201918171615

Col 109876543

Option 3 12x10* Row 13 23 14 24 22 21 20 19 18 17 16 15

32 MB Col 13AP12111098765 43

14x8* Row 13 12 11 23 14242221201918171615

Col 1211AP 109876543

11x11 Row 23 14242221201918171615

Col 131211109876543

12x10 Row 13 23 14242221201918171615

Col 1211109876543

13x9 Row 12 13 23 14242221201918171615

Col 11109876543

Option 4 14x9* Row 25 13 12 23 14242221201918171615

64 MB Col 1312AP 111098765 43

13x10 Row 13 25 23 14242221201918171615

Col 1211109876543

12x11 Row 25 23 14242221201918171615

Col 131211109876543

Option 5 14x10* Row 25 14 13 23 26 24 22 21 20 19 18 17 16 15

128 MB Col 1413AP1211109876543

13x11 Row 14 25 23 26242221201918171615

Col 131211109876543

12x12 Row 25 23 26242221201918171615

Col 14131211109876543

82443BX Host Bridge Datasheet

4-23

Function al Descr i pti on

4.3.3 SDRAMC Register Programming

Several timing parameters are programmable when using SDRAM in a Intel® 440BX AGPset

system. The following table summarizes the programmable parameters.

The 82443BX can support any combination of CAS# Latency, RAS# to CAS# Delay and RAS#

Precharge. Two additional bits are provided for controlling CS# assertion. The first is the Leadoff

Timing bits which effectively control when the command lines (SRAS#, SCAS# and WE#) are

considered valid on the interf ace and hence when CS# can b e asserted for CPU read leadof f c ycles.

In the fastest timing mode, CS# can be asserted in clock three. This enables a 7 clock page hit

performance with CAS# Latency two devices and one clock MD to HD delay. This field controls

when the first assertion of CS# occurs for read cycles initiated by the CPU. This assertion may be

for a read, row activate or precharge command. The MA lines along with the command lines

(SRA S#, SCAS # and WE#) are driven in cloc k two, however the clock to output delay timing is

slower than the other modes. Use of this mode may require a lightly loaded SDRAM interface.

4.3.4 DRAMT Register Programming

Various EDO timing parameters are programmable in the 82443BX. The ranges provide support

for the v arious loading conf igurations at 66 MHz. These are programmed via the DRAMT (DRAM

Timing) register. Only 60 ns EDO DRAMs are supported and at 66 MHz only. Thus, certain

parameters are fixed and are not programmable.

Table 4-12. Programmable SDRAM Timing Parameters

Parameter SDR AMC Bit Values (DCLKs)

CAS# Latency CL 2,3

RAS# to CAS# Delay SRCD 2,3

RAS# Precharge SRP 2,3

Leadoff CS# assertion LCT 3,4

Table 4-13. EDO DRAM Timing Parameters

Parameter 60 ns EDO Spec (ns) 66 MHz CLKs

RAS# Precharge 40 3

RAS# Pulse Width 60 5

RAS# to CAS# Delay 20–45 3

CAS# Precharge 10 1

CAS# Pulse Width 15 1

WE# Setup to CAS# Falling 0 1

WE# Hold from CAS# Falling 10 1

MA Setup to RAS#/CAS# 0 1 or 2

MA Hold from RAS#/CAS# 10 1

MD Setup to CAS# 0 1

MD Hold from CAS# 10 1

Functional Description

4-24

82443BX Host Bridge Datasheet

4.3.5 SDRAM Paging Policy

Open page arbitration is a paging policy which leaves pages open when handing off ow nership of

DRAM among masters, and places no restrictions on the number of rows which may have open

pages at any given time.

Features include:

1) Pipelined arbitration allows row/bank/page operations for next cycle to occur while current

DRAM access is performed.

2) Maintaining 2, or 4 banks open at once, in up to 8 rows at a time.

4.4 PCI Interface

The 82443BX Host Bridge provides a PCI bus interface that is compliant with the PCI Local Bus

Specifi cation, Re vision 2.1 . The implementation is optimized for high-per formance data stream ing

when the 82443BX is acting as either the target or the initiator on the PCI bus. The 82443BX

supports the conventional PCI interface referred to as PCI and AGP/PCI interface referred to as

AGP for PCI transactions and AGP for PCI transactions using the AGP enhanced protocols. AGP

cycles using the enhanced protocols are non-snoopable cycles targeted at DRAM.

4.5 AGP Interface

The 82443BX Host Bridge pro vides a A GP b us interface that is compliant with the A.G.P. Interface

Specification, Revision 1.0. The 82443BX supports AGP/PCI interface referred to as AGP for PCI

transactions and AGP for PCI transactions using the AGP enhanced protocols.

82443BX Host Bridge Datasheet

4-25

Function al Descr i pti on

4.6 Data Integrity Support

The 82443BX supports ECC (Error Checking and Correcting) or EC (Error Checking) data

integrity modes on the 64-bit DRAM interface. The Intel® 440BX AGPset does not support the

Pentium‚ Pro processor bus ECC protect ion. This mechanism is defined in the context of the

Pentium Pro processor bus specification to support building of mission critical fault-tolerant

systems. The ECC generation capability is essen tial for the high-end multiprocessor platforms

where robustness of the system depends on the complexity of the routing of the Pentium Pro

processor bus signals and operational bus frequency. UP/DP platforms based on the Intel® 440BX

AGPset do not have the same requirements and therefore, the 82443BX does not support Pentium

Pro processor bus ECC. Both the EC mode and the ECC mode are supported with either SDRAM

or EDO DRAM.

4.6.1 Data Integrity Mode Selection

The 82443BX supports three modes of data integrity on the memory interface.

•No ECC with Byte-w ise write support

•EC Mode (Error Checking only, no correction)

•ECC Mode (Error Checking and Correcting)

These modes are selected via the DRAM Data Integrity Mode (DDIM) field in the NBXCFG

4.6.1.1 Non-ECC (Default Mode of Operation)

After CPURST#, the 82443BX ECC control lo

ic is set in the default mode, no data inte

rit

or Non-ECC. This is the hi

hest performance mode for the memor

interface. Reads

from memor

are not dela

ed for error checkin

and correctin

and writes of less than a

QWord are performed without an

overhead.

4.6.1.2 EC Mode

When the NBXCFG Register, b its 8:7 (DDIM) are set to 01, the 82443BX DRAM Controller is in

EC mode. In this mode, the 82443BX external signals MECC[7:0] are driven with a protection

code on writes and are checked with an internally generated code on reads. Writes of less than a

QWord are performed as read-merge-write operations.

In EC mode, the 82443BX checks for errors on reads; however, it does not correct the data that is

returned to the requesting agent. Also memory scrubbing is not performed. Note that the ECC code

always protects or covers an entire QWord of data. When a write of less than a QWord is initiated,

the QWord wh ich is targeted by the write must be read, the new write data merged and the entire

new QWord must then be written back to memory. Partial writes (writes of less than a QWord) are

slowed since this read-merge-write operation is required.

4.6.1.3 ECC Mode

Selection between ECC and EC mode is performed entirely by software. If the system designer

decides to select ECC protection for the 72-bit memory array (64bit memory data bus plus 8 ECC

check bits), then MECC[7:0] sig nals carry ECC information to the 82443BX. The 8244 3BX

generates/checks ECC as described in det a il the following sections.

Functional Description

4-26

82443BX Host Bridge Datasheet

4.6.1.4 ECC Generation and Error Detection/Correction and Reporting

The 82443BX ECC logic implements the ECC code which is compatible with the algorithm used

for the Pentium Pro processor data bus ECC protection. The code is described in the Pentium Pro

processor bus specif ication.

ECC Generation

When enabled, the DRAM ECC mechanism allows automatic generation of an 8-bit protection

code for the 64-bit (QWord) of data during DRAM write operations. If the originally requested

write operation transfers single or multiple QWords, then the ECC-protected DRAM writes are

completed with no ov erhead. That is, ECC code is calculated and written along with the data. If the

originally requested write operation transfers less than 64bits of data (less than a QWord), then the

82443BX performs a READ-MERGE-WRITE operation.

ECC Checking and Correction

When enabled , the ECC mechanism allows a detection of single-bit and multiple-bit errors and

recovery of single-bit errors. During DRAM read operations, a full QWord of data (8 bytes) is

always transferred from DRAM to the 82443BX regardless of the size of the originally requested

data. Both 64 -bit data and 8-bit ECC code are trans ferred simultaneously from DRAM to the

82443BX. The ECC checking logic in the 82443BX generates a new ECC code for the received

64-bit data and compares it with receiv ed ECC code. If a single-bit error is detected the ECC logic

generates a new “recovered” 64-bit QWord with a pattern which correspo nds to the originally

received 8-bit ECC protection code. The corrected data is returned to the requester (the CPU, PCI

master or AGP master). Additio nally, the 82443BX ensures that th e data is corrected in main

memory so that accumulation of errors is prevented. Another error within the same QWord would

result in a double-bit error which is unrecoverable. This is known as hardware scrubbing since it

requires no software intervention to correct the data in memory.

ECC Error Reporting

For single-bit error indication, the SEF flag is set by the 82443BX in the ERRSTS (Error Status)

where the error occurred is stored in the Single-bit First Row Error (SBFRE) field in the Error

Status Register. Similarly, for multiple bit error indication, the MEF flag is set in the ERRSTS

multi-bit error the row number is stored in the Multi-bit First Row Error (MBFRE) field in the

Error Status register. In both single-bit and multiple-bit error cases, after logging the first error, the

Error Status register is locked until the software writes to the respective flags and clears the SEF

and MEF bits. This error condition can also be optionally reported to the system via the SERR#

mechanism. This functionality is controlled by the ERRCMD (Error Command) re g ister. When bit

1 of the Error Command register is set to 1, an occurrence of a multiple bit error is signaled by the

assertion of SERR#. When bit 0 of the Erro r Command register is set to 1, an occurrence of a single

bit error is signaled by the assertion of SERR#. Reporting of single bit errors via SERR# is not

critical since these errors ar e no t only corr ected as data is delivered to the requ ester and th e erro r is

automatically corrected in memory. However, system software may monitor the occurrence of

single bit errors to indicate the presence of an unreliable DIMM when single bit errors frequently

occur.

Note: Any ECC errors received during initialization should be ignored.

After a single-bit correctable ECC error has occurred, it is reported either via hardwar e mechanism

or via software mechanism (periodic polling of the ERRSTS register). After a single bit error has

occurred, the 82443BX then initiates a write to the location wh ere the error occurred with the

82443BX Host Bridge Datasheet

4-27

Function al Descr i pti on

corrected data. This feature is known as hardware scrubbing and eliminates the need for software

scrubbing routines. Note that information in the ERRSTS register can be used later to po int to a

faulty DRAM DIMM if the single-bit errors continually occur during access to that DIMM.

Multi-bit uncorrectable errors are fatal system errors and will cause the 82443BX to assert the

SERR# signal, if bit 1 of the ERRCMD register is set to 1. When an uncorrectable error is detected,

the 82443BX will latch the ro w # where the error occurred Multi-bit First Ro w Err or (MBFRE) bit

in the ERRSTS register. This information can be used later to point to a faulty DRAM DIMM.

Note: When ECC is enabled, the whole DRAM array MUST be first initialized b y doing writes before the

DRAM read operations can b e perform ed. This will establish the correlation between 64-bit data

and associated 8-bit ECC code which does not exist after power-on.

4.6.1.5 O

timum ECC Covera

Note that the 82443B X requirement is only that the me mory array is 72 bits (64 bit memory data

bus plus 8 ECC check bits) wide to select ECC or EC protection. The 82443BX does not assume

any specific configuration or ordering of memory bits.

4.6.2 DRAM ECC Err or Signaling Mec h anism

When ECC is enabled and ERRCMD is used to set S E RR# functionality, ECC errors are sign a led

to the system via the SERR# pin. The 82443BX can be programmed to signal SERR# on

uncorrectable errors, correctable errors, or both. The type of error condition is latched until cleared

by software (regardless of SERR# signaling).

When a single-bit error is detected, the offending DRAM row ID is latched in the Single-bit First

Ro w Error (SBFRE) fi eld in the ERRSTS register and the SEF (Single-bit Error Flag) bit is set to 1.

The latched row v alue is held until software e xplicitly clears the error status flag (SEF bit). When a

multiple-bit (unco r rectable) error is det ected, the offending DRAM row ID is latched in the Multi-

bit First Row Error (MBFRE) field in the ERRS TS register and the MEF (Multi-bit Error Flag) is

set to 1. The latched row value is held until software explicitly clears the error status flag (MEF

bit).

4.6.3 CPU Bus Integrity

The Intel® 440BX AGPset does not support the Pentium Pro processor bus inte

rit

mechanisms. It does not provide support for data protection via ECC, and address/

uest si

nal protection via parit

, nor does it support bus protocol error checkin

reportin

4.6.4 PCI Bus Integrity

The 82443BX implements Parity generation on the PAR pin as defi ned by the PCI Rev. 2.1

Specifi cation for bo th Primary and Secon dary PCI bus. The 8244 3BX does n ot cont ain the PE RR#

pin, however the 82443BX will check and report data parity errors on either the Primary or

Secondary PCI buses. Data and address parity errors are reported on SERR#.

Functional Description

4-28

82443BX Host Bridge Datasheet

4.7 System Clocking

Figure 4-6 shows the clock architecture for a typical Intel® 440BX AGPset system.

4.8 Power Manag e men t

This section focuses on the 82443BX power management features only. The PIIX4E datasheet

along with this section provide the complete system power management description.

4.8.1 Overview

Power Management Features Supported by the 82443BX

•Susp end Res ume

•Clock Control

•SDRAM Power Down Mode

•SMRAM

•ACPI and PCI-PM

Figure 4-6. Typical Intel® 440BX AGPset System Clocking

DCLK[15:0]

DCLK

100/66MHz

DCLKWR

82443BX

CK100 Pentium® II

Processor

CKBF SDRAM

GCLKIN

GCLKOUT

133/66MHz

BXHCLK

100/66MHz

PCLKx

33 MHz

BXPCLKx

33 MHz

CPU/HCLK

100/66MHz

100/66#

82443BX Host Bridge Datasheet

4-29

Function al Descr i pti on

Low-Power Modes Supported by the 82443BX

The 82443BX supports a variety of system-wide low power modes using the following functions:

•Hardware interface with PIIX4E is used to indicate:

— Suspend mode entry.

— Resume from suspend.

— Whether to reset “resume logic” during resume from Suspend to Disk (STD).

— Wheth er to automatically switch from suspend to normal refresh

•Automatic transi tion from normal to suspend refresh.

•Optional automatic transition from su spend to normal refresh .

•Optional CPU reset during resume from Power On Suspend (POS).

•Variety of Suspend refresh types:

— Self Refresh for SDRAMs.

— Optional Self Refresh for EDO.

— Optional CAS Before RAS (CBR) refresh for EDO. Integrated Ring oscillator is used to

provide the time base for the associated logic.

— Programmable slow refresh, relevant for CBR refresh only.

•I/O pins isolation to significantly reduce power consumption while in POS and STR modes.

Based on the above functions, the 82443BX distinguishes the following system-wide low power

modes:

•STR and POS suspend entry and e xit are gener ally handled in the same mann er. The follo wing

exceptions are related to POS:

— POS resume sequence may or may not include CPU reset. STR, with PCIRST# active

alw ays i ncludes CPU reset.

— POS resume sequence requires hardware transition from suspend to normal refresh. STR,

with PCIRST# active requires software init iated transition.

•STD resume is h andl ed t he s ame as power on sequence, including co mpl et e res et of 82443BX

state.

Clock Control Functions Supported by 82 443BX

•Internal clock gating: this function allows the 82443BX to gate the clock to the majority of its

logic while there is no pending events to handle.

•The Primary PCI bus includes the support of the CLKRUN#, which enables the PIIX4E to

dynamically disable the primary PCICLK and for the 82443BX and PCI peripheral to re-

enable the clock when it is needed to perform a transaction.

•When an AGP port is not available on the sy stem, a strapping option allows the 82443 BX to

permanently disable all clocks associated with AGP logic.

Functional Description

4-30

82443BX Host Bridge Datasheet

SDRAM Power Down Mode

The 82443BX supports SDRAM power down mode. The 82443BX also provides a capability to

dynamically enter the SDRAM into low power mode when DRAM rows are idle and resume

DRAM activity when transactions request the access to DRAM.

SMRAM Functions

The 82443BX provides the normal SMRAM range mapping, in the areas below 1MB, as wel l as

extended SMRAM ranges that are mapped in cacheable ranges above 1MB. In addition, the

82443BX pro v ides the normal co ntrol m echanism to initialize, close for data accesses and lock the

SMRAM range.

Summary of ACPI Functions

The 82443BX provides an optional decoding of pm2_control register in IO port 22h. This IO port

can be used to disable the 82443BX arbiters for PCI and AGP initiate d cycles.

Desktop vs . Mobile Power Management Funct io ns

In general, all mobile functions of the 82443BX are available in the desktop configuration. Due to

system design limitations, however, certain functions are not supported in a desktop environment

(i.e., POS/C3 state).

In Mobile systems, when system exits low power modes such as deep sleep or POS, the AGP

devices should not gene rate a request, using AGP semantics, for a duration of at least 33 us ec.

System Power Modes

Table 4-14 provides an overview of how the above features map into system-wide low power

modes.

82443BX Host Bridge Datasheet

4-31

Function al Descr i pti on

Table 4-14. Low Power Mode

System Suspend State 82443BX

State Description POS Exit

PCIRS T External Clk

HCLK PCLK

Powered-On ON

The 82443BX is fully on and

operating normally.

Internal clock gating as well as PCI

CLKRUN# may be enabled.

N/A Active Active

CPU STOP_GRANT /

QUICK_START

(C2) ON

This is transparent to the 82443BX

as external HCLK and PCLK are

unaff ected. Host Bus is Idle howe v er.

Internal clock gating as well as PCI

CLKRUN# may be enabled.

N/A Active Active

CPU STOP CLOCK (C3)

(DEE P SLEE P) POS HCLK clock is kept low. The

82443BX maintains DRAM refresh

using suspend refresh. NLow

Low or

Active

Powered On Suspend

(POS, POSCL) POS

The only running clock is the RTC

clock. The 82443BX maintains

DRAM refresh using suspend

refresh. When resume, the 82443BX

may or may not generate CPU reset.

NLowLow

Powered On Suspend

(POSCL)

The only running clock is the RTC

clock. The 82443BX maintains

DRAM refresh using suspend

refresh. On resume, PIIX 4E

generates PCI reset.

YLowLow

Suspend to RAM

(STR) POS

CPU and other components (with the

exception of DRAM and PIIX4E

resume logic) are assumed to be

powered OFF.

The 82443BX maintains DRAM

refresh using suspend refresh. All

82443BX logic, with the exception of

resume and refresh are inactive .

YLowLow

Suspend -to-Disk (STD)

or Powe red-Off OFF

Entire system is powered OFF except

for PIIX4E resume and RTC wells.

Upon resume, the 82443BX resets its

entire state.

N/A X X

Functional Description

4-32

82443BX Host Bridge Datasheet

4.8.2 82443BX Reset

The 82443BX reset function is an integral part of the suspend resume functions. The 82443BX

supports the normal reset function in a desktop platform, as well as the v arious po wer-up reset and

resume reset functions in the mobile platform. In this section, the power-up reset is described. The

resume from suspend sequences are described in the following section.

Table 4-15. AGPset Reset

Table 4-16. Reset Signals

Signal Asserted

with PCIRST # System Devices or

Buses Affected Signal

Source Description

PCIRST# - PCI bus, 82443BX

NB, PIIX4E PIIX4E PCIRST# is used in po wer -up sequence

as well as resume from STR or STD.

CPURST# Always CPU 82443BX CPU reset signal. CPURST# pin resides

in 82443BX.

RSTDRV Always ISA bus / X-Bu s

devices PIIX4E ISA bus reset. Directly derived from

PCIRST#. Resides in PIIX4E main

voltage well.

SUS_STAT# N/A PIIX4 E

only

SUS_STAT# signals a suspend mode

entry and exit. Both signals originate

from PIIX4E in its suspend voltage well.

INIT# No CPU PIIX4E CPU Soft Reset generated by PIIX4E.

Exter nal CPU

Clock Ratio

Straps External CPU Strap Glue

A20M#, IGNNE#,

INTR, NMI

RSTDRV

SUB_STAT1#

PCIRST#

PIIX4E#

NBX#

PWROK

INIT#

CRESET#

CPURST#

Pentium® Pro

Processor

2to1 Mux

82443BX Host Bridge Datasheet

4-33

Function al Descr i pti on

4.8.2.1 CPU Reset

The CPU reset is generated by the 82443BX in the following case:

•CPURST# is always asserted if PCIRST# is asserted.

•CPURST# is asserted during resume sequence from POS CRst_En= 1 .

The 82443BX deasserts CPURST# 1 ms after detecting the rising edge of PCIRST#. The

CPURST# is synchronous to host bus clock.

PCIRST# must be asserted when the system resumes from low power mode of which power is

remov ed, including re sume from STR or STD and power up sequence. In these cases, CPURST# is

activated with the assumption that CPU power is removed as well and in order to enforce correct

resume sequence.

When resuming from POS, the PCIRST# and CPURST# are typically not used, to speed up the

resume sequence. The op tion to reset the CPU, in this case, is available by using the CRst_ En

configuration bit option.

When the user performs a soft reset, the PIIX4E drives SUSTAT# to the 82443BX. This forces the

82443BX to switch to a suspend refresh state. When the BIOS attempts to execute cycles to

DRAM, the 82443BX will not accept these cycles because it believes that it is in a suspend state.

After coming out of reset, software must set the Normal refresh enable bit (bit4, Power

Management Control register at Offset 7Ah) in the 82443BX before doing an access to memory.

4.8.2.2 CPU Clock Ratio Straps

The Pentium Pro processors require their internal clock ratio to be set up via strapping pins

multiplexed onto signals A20M#, IGNE#, INTR, and NMI. These signals should reflect the

strappin g v alues dur ing the d easserted edge o f CPURST# signal and b e held stable for between 2 to

20 clocks. HCLKs after CPURST# is deasserted.

The 82443BX is designed to support CPU strapping options with external logic, when PIIX4E is

used. Figure 4-8 illustrates the strapping pin timing when using the external glue logic (necessary

for PIIX4E). The external mux is switched via the CRESET# signal which is a 2 clock delayed

version of CPUR ST#.

Figure 4-7. Reset CPURST# in a Desktop or Mobile System When PCIRST# Asserted

1....

HCLK

PCIRST#

PCLK

CPURST#

CRESET#

0000 1m SEC

Functional Description

4-34

82443BX Host Bridge Datasheet

4.8.2.3 82443BX Straps

The 82443BX strapping options are latched in the risin g ed ge of PCIRST#.

4.8.3 Suspend Resume

4.8.3.1 Suspend Resume protocols

The suspend resume sequences are indicated to the 82443BX by the PIIX4E, using SUS_STAT#,

and PCIRST#. In add ition, the 82443BX contains NREF_EN and CRst_En configuration bits that

participate in the suspend resume seq uences. As a result of suspend resume, the 82443 BX performs

the following activities: Changing its refresh mode, performing internal and CPU reset and Isolate

or re-enable normal IO buffers.

4.8.3.2 Suspend Refresh

Suspend Ref resh Modes

The 82443BX supports suspend refresh by providing a mechanism to transition in and out of

suspend. The supported suspend refresh types are:

•Self Refresh when SDRAM are used

•Self Refresh when EDO -DRAMs are used

•CBR Refresh when EDO-DRAMs are used

Figure 4-8. External Glue Logic Drives CPU Clock Ratio Straps

1 ms

1 33,333

....

HCLK

SUS_DIS strap

CPU strap values from exter nal Glue Logic

Suspend disable value latched when PCIRST#↑

PCIRST#

PCLK

CRESET#

CPU straps

p_creset#

Table 4-17. Suspend / Resume Events and Activities

State SUSTAT# PCIRST# CrstEn RESET REFRESH IO

BUFFERS

ON assert inactive - - s witch to suspend refresh isolate

POSCL/STR deassert active - reset exclude

resume/ref logic

suspend refresh

NREF_EN remains

inactive enable

POS deassert inactive 0 no resets auto switch to normal ref

NREF_EN is set enable

POSCCL deassert inactive 1 reset CPU only auto switch to normal ref

NREF_EN is set enable

82443BX Host Bridge Datasheet

4-35

Function al Descr i pti on

SDRAM S uspend Refresh

When the 82443B X is configur ed for 3 DIMMs, six CKE signals are pro vided. When the 82443BX

is configured for 4 DIMMs, a single GCKE (global CKE) is provided to allow an e xternal de vice to

correctly drive the external CKE signals to the SDRAM devices. An additional 3 DIMM

configuration is where only CKE0 is provided. A detailed description of the DRAM signal

functions is given in the Chapter 2, “Signal Description”.

For the Registered DIMMs the CKE function is not supported. The stacking technology used for

registered DIMMs prohibits the use of the CKE function. For registered DIMMs, components are

stacked on top of one another. The stacked components are physically in the same row, but

logically in separate rows. The stacked components connect all pins together, except for the CS#

pin, in order to address components in different rows. Since the CKE pins for the components are

connected together, and the components are logically in different rows, the CKE function is not

supported.

EDO DRAM Suspend Refresh

The 82443B X NB su pport s tw o modes of EDO refresh durin g suspen d: C AS-befor e-RAS and Sel f-

refresh. The refresh mo de is dependent on the Suspend Refresh type bit (SRT) in the Miscellaneous

Control Reg i st e r.

4.8.4 Clock Contro l Functions

The 82443BX implements an independent Clock Gating power savings feature to reduce its own

average power consumption. The 82443BX clock gating functions works along with the primary

PCI bus CLKRUN# function.

The Clock Gati ng function is enab led by setting the GCLKEN Configuration bit. This function

default v alue is 0. The AGP interface’s clock domain can be permanently disabled b y the A GP_DIS

configuration bi t. This allows further power savings in systems that AGP is not use d.

CLKRUN Clocki ng Sta te s

There are three states in the CLKRUN# protocol:

•Clock Runnin

: The clock is runnin

and the bus is operational.

•Clock Sto

uest: The central resource has indicated on the CLKRUN# line that

the clock is about to stop.

•Clock Sto

ed: The clock is stopped with CLKRUN# bein

monitored for a restart.

Table 4-18. SDRAM Suspend Refresh Configuration Modes

CONFIG SDRAM

PWR FUNCTION

3 DIMM, CKE[5:0] driven, self-refresh entr y staggered. SDRAM dynamic

power do wn available.

3 DIMM, CKE0 only, self-refresh entry not staggered. SDRAM dynamic power

down unavailable.

4 DIMM, GCKE only, self-refresh entry staggered. SDRA M dynam ic power

down unavailable.

Functional Description

4-36

82443BX Host Bridge Datasheet

4.8.5 SDRAM Power Down Mode

The 82443BX supports a SDRAM power down mode to minimize SDRAM power usage. The

82443BX controls the SDRAM power mode per row, when all banks in a given row are idle, the

associated CKE signal is deasserted. When a powered down row address is requested, the

associated CKE is asserted.

4.8.6 SMRAM

SMRAM ranges

The 82443BX supports the use of main memory as System Management RAM (SMRAM)

enabling the use of System Management Mode. There are two SMRAM options: Compatible

SMRAM (C_SMRAM) and Extended SMRAM (E_SMRAM). System Management RAM

(SMRAM) space provides a memory area that is available for the SMI handler's and code and data

storage. This memory resource is normally hidden from the operating system so that the processor

has immediate access to this memory space upon entry to SMM. 82443BX prov ides three SMRAM

options:

•Below 1 MB option that supports compatible SMI handlers.

•Above 1 MB option that allows new SMI handlers to execute with write-back cacheable

SMRAM.

•Optional larger write-back cacheable T_SEG area from 128KB to 1MB in size above 1 MB

that is reserved from the highest area in system DRAM memory. The above 1 MB solutions

require changes to compatible SMRAM handlers code to properly execute above 1 MB.

Compatible SMRAM (C_SMRAM)

This is the traditio nal SMRAM feature supported in Intel AGPsets. When this function is enabled

via C_BASE_SEG[2:0]=010 and G_SMRAME=1 of the SMRAMC register, the 82443BX

reserves 000A0000h through 000BFFFFh (A and B segments) of the main memory for use as non-

cacheable SMRAM.

The SMI handler can set the CLS bit to enable data accesses to aliased memory space, while code

fetches access the SMRAM space.

Extended SMRAM (E_SMRAM)

This feature in the 82443BX extend the SMRAM space up to 1 MB and provide write-back

cacheability.

The TSEG size is 128 KBs, 256 KBs, 512 KBs or 1 MB, as defined by TSEG_SZ[1:0] of the

SMRAMC register.

The CPU can access these memory ranges by one of the following mechanisms:

•The processor can access SMRAM while in the SMM mode. A processor access to while not

in SMM and with while the D_OPN bit is reset will be forw ar ded to PCI bus and a status bit is

set in the SMRAMC register.

•The processor can access SMRAM while the D_OPN bit is set.

82443BX Host Bridge Datasheet

5-1

Pinout and Pack age Information

Pinout and Package Information

5.1 82443BX Pinout

Figure 5-1 an d Figure 5-2 sho w the ball footprint of the 82443BX package. These f igures represent

the pinout by ball number. For an alphabetical list of the pinout by signal name refer to Table 5-1.

Pinout and Package Information

5-2

82443BX Host Bridge Datasheet

NOTES:

1. The following signals are multiplexed. See the following Alphabetical pin list for details.

a. CSA[5:0]# is multiplexe d with RASA[5:0]#; CSB[5:0]# is multiplexe d with RASB[5:0]#

b. CKE[3 :2] is multi plexed with CSA[7: 6 ]#; CKE[ 5:4 ] is mul tipl e x ed wit h CSB[ 7:6] #; CKE1 is mult iplexed with

GCKE; CKE0 is mult ip lexed with FENA

c. DQMA[7:0] is multiplexed with CASA[7:0]#; DQMB[5,1] is multiplexed with CASB[5,1]#

Figure 5-1. 82443BX Pinout (Top View–left side)

12345678910111213

VSS AD20 PCIRST# AD25 AD29 PREQ0# HD56# HD62# HD55# HD54# HD49# HD47# HD40#

BVCC PCLKIN AD22 AD27 AD28 PHOLD# HD50# HD61# HD63# HD53# HD48# HD42# HD36#

CAD19 REFVCC AD21 C/BE3# VSS AD31 PREQ1# HD52# VSS HD60# HD59# HD51# HD44#

DAD16 AD18 AD17 AD23 AD26 PHLDA# PGNT1# PREQ3# HD58# PREQ4# HD46# HD41# HD39#

EIRDY# FRAME# VSS C/BE2# AD24 AD30 PGNT0# PGNT3# PGNT4# PGNT2# HD57# VSS HD45#

FSERR# PLOCK# DEVSEL# STOP# TRDY# VSS VCC VSS VCC PREQ2#

GAD13 AD14 C/BE1# AD15 PAR VCC

HAD8 AD7 AD10 AD12 AD11 VSS

JAD5 AD6 VSS C/BE0# AD9 VCC

KSBA0 AD1 AD3 AD2 AD4 AD0

LST2 ST1 GGNT# ST0 GREQ# VCC VSS VCC

MSBA2 SBA1 PIPE# RBF# VSS VSS VCC VSS

NVSS SBA3 SBSTB AGPREF GCLKIN VCC VSS VSS

PVCC SBA4 SBA6 SBA5 GCLKO VCC VSS VSS

RSBA7 GAD31 GAD29 GAD30 VSS VSS VCC VSS

TGAD27 GAD26 GAD24 GAD25 ADSTB_B VCC VSS VCC

UGAD23 GC/BE3# GAD22 GAD21 GAD19 GAD28

VGAD20 GAD17 VSS GC/BE2# GIRDY# VCC

WGAD16 GAD18 GFRAME# GTRDY# GDEVSEL# VSS

YGSTOP# GPAR GAD15 GC/BE1# GAD14 VCC

AA GAD13 GAD12 GAD10 GAD11 GAD9 VSS VCC VSS VCC MECC1

AB GAD8 GC/BE0# VSS GAD7 GAD0 MD34 MD5 MD8 MD9 MD12 MD46 VSS SCASB#

AC GAD6 ADSTB_A GAD5 CLKRUN# MD32 MD35 MD6 MD39 MD10 MD13 MD47 WEB# DQMA1

AD GAD4 GAD3 GAD2 SUSTAT# VSS MD3 MD37 MD40 VSS MD44 MD15 MECC5 DQMA0

AE VCC GAD1 WSC# MD1 MD33 MD4 MD38 MD42 MD11 MD45 MECC0 WEA# DQMB1

AF VSS VCC BXPWROK MD0 MD2 MD36 MD7 MD41 MD43 MD14 MECC4 SCASA# VSS

82443BX Host Bridge Datasheet

5-3

Pinout and Pack age Information

NOTES:

1. The following signals are multiplexed. See the f ollowing Alphabetical pin list for details.

d. CSA[5:0]# i s multipl exed with RASA[5:0]#; CSB[5:0]# is multipl exed with RASB[5 :0] #

e. CKE[3:2] is multiplexed with CSA[7:6]#; CKE[5:4] is multiplexed with CSB[7:6]#; CKE1 is multiplexed with

GCKE; CKE0 is multiplexed with FENA

f. DQMA[7:0] is multiplexed with CASA[7:0]#; DQMB[ 5, 1] is mul tiplexed with CASB[5,1]#

Figure 5-2. 82443BX Pinout (Top View–right side)

14 15 16 17 18 19 20 21 22 23 24 25 26

VSS HD33# HD31# HD27# HD19# HD20# HD10# HD6# HD3# HA29# HA24# HA22# VSS A

HD43# HD32# HD29# HD25# HD21# HD18# HD12# HD8# HD0# CPURST# HA27# HA20# BREQ0# B

HD37# HD28# HD26# HD22# VSS HD17# HD7# HD5# VSS HA26# HA28# HA23# HA21# C

HD34# HD35# HD30# HD24# HD16# HD15# HD14# HD4# HD1# HA31# HA25# HA18# HA19# D

HD38# VSS GTLREFB HD23# HD13# HD11# HD9# HD2# HA30# HA15# VSS HA17# HA16# E

VTTB VCC VSS VCC VSS HA11# HA12# HA13# HA14# HA8# F

VCC HA10# HA5# HA7# HA3# HA9# G

VSS HA4# HA6# BNR# HTRDY# BPRI# H

VCC HREQ0# HREQ1# VSS HREQ4# DEFER# J

ADS# HLOCK# DRDY# HREQ2# HREQ3# RS0# K

VCC VSS VCC HITM# DBSY# HIT# RS2# RS1# L

VSS VCC VSS VSS GTLREFA VTTA TESTIN# CRESET# M

VSS VSS VCC VCC HCLKIN VSS MD31 VCC N

VSS VSS VCC NC MD30 MD 62 MD 63 V SS P

VSS VCC VSS VSS MD60MD28MD29MD61R

VCC VSS VCC MD25 MD26 MD57 MD58 MD27 T

MD59 MD54 MD24 MD23 MD55 MD56 U

VCC MD51 MD52 VSS MD53 MD22 V

VSS MD50MD18MD19MD21MD20W

VCC MECC7 MD48 MD16 MD17 MD49 Y

SRASB# VCC VSS VCC VSS DQMA6 MECC2 DQMA7 MECC6 MECC3 AA

CSA0# VSS MAA1 MAB3# MAB6# MAB7# MAB10 DCLKO NC CSB5# VSS VSS DQMA3 AB

DQMA5 CSA3# MAB1# MAA3 MAA7 MAA8 MAB9# MAA12 CKE0 CKE4 CSB3# DQMA2# CSB4# AC

DQMB5 CSA4# MAB0# MAB2# VSS MAB5# MAA10 MAB12# VSS CKE3 CSB1# DCLKWR CSB2# AD

DQMA4 CSA2# CSA5# MAA2 MAB4# MAA5 MAA9 MAB11# NC NC CKE2 CSB0# VCC AE

VCC CSA1# SRASA# MAA0 MAA4 MAA6 MAB8# MAA11 MAB13 CKE1 CKE5 MAA13 VSS AF

Pinout and Package Information

5-4

82443BX Host Bridge Datasheet

Table 5-1. 82443BX Alphabetical BGA Pin List (Sheet 1 of 4)

Signal Name Pin Signal Name Pin Signal Name Pin

AD0 K6 C/BE2# E4 GAD0 AB5

AD1 K 2 C/BE3# C4 GAD1 AE2

AD2 K4 CKE0/FENA AC22 GAD2 AD3

AD3 K3 CKE1/GCKE AF23 GAD3 AD2

AD4 K5 CKE2/CSA6 AE24 GAD4 AD1

AD5 J1 CKE3/CSA7 AD23 GAD5 AC3

AD6 J2 CKE4/CSB6 AC23 GAD6 AC1

AD7 H2 CKE5/CSB7 AF24 GAD7 AB4

AD8 H1 CLKRUN# AC4 GAD8 AB1

AD9 J5 CPURST# B23 GAD9 AA5

AD10 H3 CRESET# M26 GAD10 AA3

AD11 H5 CSA0#/RASA0# AB14 GAD11 AA4

AD12 H4 CSA1#/RASA1# AF15 GAD12 AA2

AD13 G1 CSA2#/RASA2# AE15 GAD13 AA1

AD14 G2 CSA3#/RASA3# AC15 GAD14 Y5

AD15 G4 CSA4#/RASA4# AD15 GAD15 Y3

AD16 D1 CSA5#/RASA5# AE16 GAD16 W1

AD17 D3 CSB0#/RASB0# AE25 GAD17 V2

AD18 D2 CSB1#/RASB1# AD24 GAD18 W2

AD19 C1 CSB2#/RASB2# AD26 GAD19 U5

AD20 A2 CSB3#/RASB3# AC24 GAD20 V1

AD21 C3 CSB4#/RASB4# AC26 GAD21 U4

AD22 B3 CSB5#/RASB5# AB23 GAD22 U3

AD23 D4 DBSY# L23 GAD23 U1

AD24 E5 DCLKO AB21 GAD24 T3

AD25 A4 NC AB22 GAD25 T4

AD26 D5 DCLKWR AD25 GAD26 T2

AD27 B4 DEFER# J26 GAD27 T1

AD28 B5 DEVSEL# F3 GAD28 U6

AD29 A5 DQMA0/CASA0# AD13 GAD29 R3

AD30 E6 DQMA1/CASA1# AC13 GAD30 R4

AD31 C6 DQMA2/CASA2# AC25 GAD31 R2

ADS# K21 DQMA3/CASA3# AB26 GC/BE0# AB2

ADSTB_A AC2 DQMA4/CASA4# AE14 GC/BE1# Y4

ADSTB_B T5 DQMA5/CASA5# AC14 GC/BE2# V4

AGPREF N4 DQMA6/CASA6# AA22 GC/BE3# U2

BNR# H24 DQMA7/CASA7# AA24 GCLKIN N5

BPRI# H26 DQMB1/CASB1# AE13 GCLKO P5

BREQ0# B26 DQMB5/CASB5# AD14 GDEVSEL# W5

C/BE0# J4 DRDY# K23 GFRAME# W3

C/BE1# G3 FRAME# E2 GGNT# L3

82443BX Host Bridge Datasheet

5-5

Pinout and Pack age Information

GIRDY# V5 HD4# D21 HD45# E13

GPAR Y2 HD5# C21 HD46# D11

GREQ# L5 HD6# A21 HD47# A12

GSTOP# Y1 HD7# C20 HD48# B11

GTLREFA M23 HD8# B21 HD49# A11

GTLREFB E16 HD9# E20 HD50# B7

GTRDY# W4 HD10# A20 HD51# C12

HA3# G25 HD11# E19 HD52# C8

HA4# H22 HD12# B20 HD53# B10

HA5# G23 HD13# E18 HD54# A10

HA6# H23 HD14# D20 HD55# A9

HA7# G24 HD15# D19 HD56# A7

HA8# F26 HD16# D18 HD57# E11

HA9# G26 HD17# C19 HD58# D9

HA10# G22 HD18# B19 HD59# C11

HA11# F22 HD19# A18 HD60# C10

HA12# F23 HD20# A19 HD61# B8

HA13# F24 HD21# B18 HD62# A8

HA14# F25 HD22# C17 HD63# B9

HA15# E23 HD23# E17 HIT# L24

HA16# E26 HD24# D17 HITM# L22

HA17# E25 HD25# B17 HLOCK# K22

HA18# D25 HD26# C16 HREQ0# J22

HA19# D26 HD27# A17 HREQ1# J23

HA20# B25 HD28# C15 HREQ2# K24

HA21# C26 HD29# B16 HREQ3# K25

HA22# A25 HD30# D16 HREQ4# J25

HA23# C25 HD31# A16 HTRDY# H25

HA24# A24 HD32# B15 IRDY# E1

HA25# D24 HD33# A15 MAA0 AF17

HA26# C23 HD34# D14 MAA1 AB16

HA27# B24 HD35# D15 MAA2 AE17

HA28# C24 HD36# B13 MAA3 AC17

HA29# A23 HD37# C14 MAA4 AF18

HA30# E22 HD38# E14 MAA5 AE19

HA31# D23 HD39# D13 MAA6 AF19

HCLKIN N23 HD40# A13 MAA7 AC18

HD0# B22 HD41# D12 MAA8 AC19

HD1# D22 HD42# B12 MAA9 AE20

HD2# E21 HD43# B14 MAA10 AD20

HD3# A22 HD44# C13 MAA11 AF21

Table 5-1. 82443BX Alphabetical BGA Pin List (Sheet 2 of 4)

Signal Name P in Signal Name Pin Signal Name Pin

Pinout and Package Information

5-6

82443BX Host Bridge Datasheet

MAA12 AC21 MD25 T22 MECC2 AA23

MAA13 AF25 MD26 T23 MECC3 AA26

MAB0# AD16 MD27 T26 MECC4 AF11

MAB1# AC16 MD28 R24 MECC5 AD12

MAB2# AD17 MD29 R25 MECC6 AA25

MAB3# AB17 MD30 P23 MECC7 Y22

MAB4# AE18 MD31 N25 NC P22

MAB5# AD19 MD32 AC5 NC AE22

MAB6# AB18 MD33 AE5 NC AE23

MAB7# AB19 MD34 AB6 PAR G5

MAB8# AF20 MD35 AC6 PCIRST# A3

MAB9# AC20 MD36 AF6 PCLKIN B2

MAB10 AB20 MD37 AD7 PGNT0# E7

MAB11# AE21 MD38 AE7 PGNT1# D7

MAB12# AD21 MD39 AC8 PGNT2# E10

MAB13 AF22 MD40 AD8 PGNT3# E8

MD0 AF4 MD41 AF8 PGNT4# E9

MD1 AE4 MD42 AE8 PHLDA# D6

MD2 AF5 MD43 AF9 PHOLD# B6

MD3 AD6 MD44 AD10 PIPE# M3

MD4 AE6 MD45 AE10 PLOCK# F2

MD5 AB7 MD46 AB11 PREQ0# A6

MD6 AC7 MD47 AC11 PREQ1# C7

MD7 AF7 MD48 Y23 PREQ2# F10

MD8 AB8 MD49 Y26 REQ3# D8

MD9 AB9 MD50 W22 PREQ4# D10

MD10 AC9 MD51 V22 RBF# M4

MD11 AE9 MD52 V23 REFVCC C2

MD12 AB10 MD53 V25 RS0# K26

MD13 AC10 MD54 U22 RS1# L26

MD14 AF10 MD55 U25 RS2# L25

MD15 AD11 MD56 U26 SBSTB N3

MD16 Y24 MD57 T24 SBA0 K1

MD17 Y25 MD58 T25 SBA1 M2

MD18 W23 MD59 U21 SBA2 M1

MD19 W24 MD60 R23 SBA3 N2

MD20 W26 MD61 R26 SBA4 P2

MD21 W25 MD62 P24 SBA5 P4

MD22 V26 MD63 P25 SBA6 P3

MD23 U24 MECC0 AE11 SBA7 R1

MD24 U23 MECC1 AA10 SCASA# AF12

Table 5-1. 82443BX Alphabetical BGA Pin List (Sheet 3 of 4)

Signal Name Pin Signal Name Pin Signal Name Pin

82443BX Host Bridge Datasheet

5-7

Pinout and Pack age Information

SCASB# AB13 VCC V21 VSS N14

SERR# F1 VCC Y6 VSS N15

SRASA# AF16 VCC Y21 VSS N24

SRASB# AA17 VCC AA7 VSS P12

ST0 L4 VCC AA9 VSS P13

ST1 L2 VCC AA18 VSS P14

ST2 L1 VCC AA20 VSS P15

STOP# F4 VCC AE1 VSS P26

BXPWROK AF3 VCC AE26 VSS R5

SUSTAT# AD4 VCC AF2 VSS R11

TESTIN# M25 VCC AF14 VSS R13

TRDY# F5 VSS A1 VSS R14

VCC B1 VSS A14 VSS R16

VCC F7 VSS A26 VSS R22

VCC F9 VSS C5 VSS T12

VCC F18 VSS C9 VSS T15

VCC F20 VSS C18 VSS V3

VCC G6 VSS C22 VSS V24

VCC G21 VSS E3 VSS W6

VCC J6 VSS E12 VSS W21

VCC J21 VSS E15 VSS AA6

VCC L11 VSS E24 VSS AA8

VCC L13 VSS F6 VSS AA19

VCC L14 VSS F8 VSS AA21

VCC L16 VSS F19 VSS AB3

VCC M12 VSS F21 VSS AB12

VCC M15 VSS H6 VSS AB15

VCC N11 VSS H21 VSS AB24

VCC N16 VSS J3 VSS AB25

VCC N22 VSS J24 VSS AD5

VCC N26 VSS L12 VSS AD9

VCC P1 VSS L15 VSS AD18

VCC P11 VSS M5 VSS AD22

VCC P16 VSS M11 VSS AF1

VCC R12 VSS M13 VSS AF13

VCC R15 VSS M14 VSS AF26

VCC T11 VSS M16 VTTA M24

VCC T13 VSS M22 VTTB F17

VCC T14 VSS N1 WEA# AE12

VCC T16 VSS N12 WEB# AC12

VCC V6 VSS N13 WSC# AE3

Table 5-1. 82443BX Alphabetical BGA Pin List (Sheet 4 of 4)

Signal Name P in Signal Name Pin Signal Name Pin

Pinout and Package Information

5-8

82443BX Host Bridge Datasheet

5.2 Package Dimensions

This specification outlines the mechanical dimen sions for the 82443BX Host Bridge. The package

is a 492 ball grid array (BGA).

Figure 5-3. 82443BX BGA Package Dimensions—Top and Side Views

Pin A1 I.D.

Pin A1 corner

EE1

Top View

AA2

Side View 492_pk

1.vsd

82443BX Host Bridge Datasheet

5-9

Pinout and Pack age Information

Figure 5-4. 82443BX BGA Package Dimensions—Bottom Views

Table 5-2. 82443BX Package Dimensions (492 BGA)

Symbol e=1.27 mm (solder ball pitch) Note

Min Nominal Max

A 2.17 2.38 2.59

A1 0.50 0.60 0.70

A2 1.12 1.17 1.22

D 34.80 35.00 35.20

D1 29.75 30.00 30.25

E 34.80 35.00 35.20

E1 29.75 30.00 30.25

I 1.63 REF.

J 1.63 REF.

M 26 x 26 Matrix

N4.92

b 0.60 0.75 0.90

c 0.55 0.61 0.67

210162022 35791113151719 1

25 24

4618 81214

Pin A1 corner

468 BGA

Bottom View

UNITED STATES AND CANA DA

Intel Corporation

2200 Mission College Boulevard

P.O. Box 58119

Santa Clara, CA 95052-8119

USA

Tel: 408-765-8080

EUROPE

Intel Corporation (U.K.) Ltd.

Pipers Way

Swindon

Wiltshire SN3 1RJ

Tel: +44 (0) 1793 403000

ASIA PACIFIC

Intel Semiconductor Ltd.

32/F Two Pacific Place

88 Queensway, Central

Hong Kong

Tel: (852) 844-4555

JAPAN

Intel Japan K.K.

5-6 Tokodai, Tsukuba-shi

Ibaraki, 300-26

Japan

Te l: +81-298-47-8511

SOUTH AMERICA

Intel Semicondutores do Brazil LTDA

Rua Florida 1703-2 and CJ 22

04565-001-Sao Paulo, SP

Brazil

Tel: 55-11-5505-2296

FOR MORE INFORM ATION

To learn more about Intel Corporation

visit our site on the World Wide Web

at http://www.intel.com/

* Other brands and names are the property of their respective owners.

Printed in USA/04 98 /PSA