TDA8296 Digital global standard low IF demodulator for analog TV and FM radio Rev. 1 -- 3 March 2011 Product data sheet 1. General description The TDA8296 is an alignment-free digital multistandard vision and sound low IF signal PLL demodulator for positive and negative video modulation including AM and FM mono sound processing. It can be used in all countries worldwide for M/N, B/G/H, I, D/K, L and L-accent standard. CVBS and SSIF/mono audio are provided via two DACs. FM radio preprocessing is included for simple interfacing with demodulator/stereo decoder backends. The IC is especially suited for the application with the NXP Silicon Tuner TDA1827x. All the processing is done in the digital domain. The chip has an `easy programming' mode to make the I2C-bus protocol very simple. In principle, only one bit sets the proper standard with recommended content. However, if this is not suitable, free programming is always possible. Note: Register 06h has to be reprogrammed to new value C4h (see Section 9.2 and Section 9.3.1). 2. Features and benefits Digital IF demodulation for all analog TV standards worldwide (M/N, B/G/H, D/K, I, L and L-accent standard) Multistandard true synchronous demodulation with active carrier regeneration Alignment-free 16 MHz typical reference frequency input (from low IF tuner) or operating as crystal oscillator Internal PLL synthesizer which allows the use of a low-cost crystal (typically 16 MHz) Especially suited for the NXP Silicon Tuner TDA1827x No SAW filter needed Low application effort and external component count in combination with the TDA1827x Simple upgrade of TDA8295 possible 12-bit low power IF ADC on chip running with 54 MHz or 27 MHz Two 10-bit DACs on chip for CVBS and SSIF or audio Easy programming for I2C-bus High flexibility due to various I2C-bus programming registers I2C-bus interface and I2C-bus feed-through for tuner programming Four I2C-bus addresses selectable via two external pins TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Gated IF AGC acting on black level by using H/V PLL or peak IF AGC (I2C-bus selectable) Internal digital logarithmic IF AGC amplifier with up to 48 dB gain and 68 dB control range Peak search tuner IF AGC for optimal adaptive drive of the IF ADC Switchable IF PLL and IF AGC loop bandwidths Precise AFC and lock detector Accurate group delay equalization for all standards Very robust IF demodulator coping with adverse field conditions Wide PLL pull-in range up to 1 660 kHz (I2C-bus selectable) CVBS and SSIF or audio output with simple postfilter (capacitor only) CVBS gain levelling stage to provide nearly constant signal amplitude during over modulation Video equalizer with eight settings Nyquist filter in video baseband Excellent video S/N (typically 60 dB weighted) High selectivity video low-pass filter for all standards Low video into sound crosstalk SSIF AGC Sound performance comparable to QSS single reference concepts AM/FM mono sound demodulator Switchable de-emphasis Excellent FM sound Good AM sound High FM Deviation mode for China Preprocessing of FM radio (mono and stereo) with highly selective digital band-pass filter No ceramic filter or external components needed for FM radio FM radio available in mono Automatic or forced mute for mono sound Automatic or forced blank for video Mostly digital FIR filter implementation (NSC notches and video low-pass filters) Three GPIO pins Power-On Reset (POR) block for reliable power-up behavior Very low total power dissipation (typically 150 mW) No power sequence requirement Standby mode (typically 5 mW) 40-pin HVQFN package CMOS technology (0.090 m 1.2 V and 3.3 V) 3. Applications TV applications Recording PC TV applications TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 2 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 4. Quick reference data Table 1. Quick reference data Power supplies 3.3 V, 1.2 V; Tamb = 25 C; PC/SC1 for L and M = 10 dB, all others 13 dB; nominal residual picture carrier of 3 % for L/L' , 10 % for M, 10 % for B/G, 12.5 % for D/K, 20 % for I; FM/AM modulation = 54 %, 1 kHz modulation frequency; measured in application PCB (see Figure 22 and Figure 23) with 16 MHz crystal frequency, terminated with 75 (CVBS) and 1 k (SSIF/audio). Operation mode set via easy programming (Section 9.3.1), otherwise stated. Low IF input signal at -3dB full scale, input frequencies as defined under row header IF input. Symbol Parameter Conditions Min Typ Max Unit VDD(1V2) supply voltage (1.2 V) digital and analog 1.1 1.2 1.3 V VDD(3V3) supply voltage (3.3 V) digital and analog 3.0 3.3 3.6 V IDD(tot)(1V2) total supply current (1.2 V) - 49 - mA IDD(tot)(3V3) total supply current (3.3 V) - 65 - mA Ptot total power dissipation default settings; fs = 54 MHz at ADC; DAC application in accordance to Figure 23 - 270 - mW fs = 54 MHz at ADC; DAC application in accordance to Figure 24 - 150 - mW Standby mode - 5 8 mW Power supply IF input Vi(p-p) peak-to-peak input voltage for full-scale ADC input (0 dBFS) 0.7 0.8 0.9 V Vi input voltage operational input related to ADC full scale; all standards; sum of all signals -3 -3 -3 dBFS fi input frequency PC / SC1 M/N standard - 5.40 / 0.90 - MHz B standard - 6.40 / 0.90 - MHz G/H standard - 6.75 / 1.25 - MHz I standard - 7.25 / 1.25 - MHz D/K standard - 6.85 / 0.35 - MHz L standard - 6.75 / 0.25 - MHz L-accent standard - 1.25 / 7.75 - MHz FM radio - 1.25 - MHz wide - 60 - kHz - 830 - kHz 115 117 - % Carrier recovery FPLL B-3dB(cl) closed-loop -3 dB bandwidth fpullin pull-in frequency range mover(PC) picture carrier over modulation index [1] black for L/L-accent standard; flat field white else IF demodulation (video equalizer in Flat mode) sup(stpb) stop-band suppression video low-pass filter (M/N, B/G/H, I, D/K, L/L-accent standard) - -60 - dB tripple(GDE) group delay equalizer ripple time peak value for B/G/H half, D/K half, I flat, M (FCC) full, L/L-accent full standard - 20 40 ns TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 3 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 1. Quick reference data ...continued Power supplies 3.3 V, 1.2 V; Tamb = 25 C; PC/SC1 for L and M = 10 dB, all others 13 dB; nominal residual picture carrier of 3 % for L/L' , 10 % for M, 10 % for B/G, 12.5 % for D/K, 20 % for I; FM/AM modulation = 54 %, 1 kHz modulation frequency; measured in application PCB (see Figure 22 and Figure 23) with 16 MHz crystal frequency, terminated with 75 (CVBS) and 1 k (SSIF/audio). Operation mode set via easy programming (Section 9.3.1), otherwise stated. Low IF input signal at -3dB full scale, input frequencies as defined under row header IF input. Symbol Parameter Conditions Min Typ Max Unit peak-to-peak output voltage negative PC modulation (all standards except L/L-accent); 75 DC load; sync-white modulation; 90 % (nominal) 0.9 1.0 1.1 V positive PC modulation (L/L-accent standard); 75 DC load; sync-white modulation; 97 % (nominal) 0.9 1.0 1.1 V all standards except M/N 4.7 4.85 - MHz M/N standard CVBS output Vo(p-p) Bvideo(-3dB) -3 dB video bandwidth overall video response; CVBS equalizer flat 3.8 3.9 - MHz resp(f) frequency response video equalizer; 8 equally spaced settings; value at 3.9 MHz -5 - +4.5 dB Gdif differential gain "ITU-T J.63 line 330" - 1.5 5 % dif differential phase "ITU-T J.63 line 330" - 1.0 3 deg (S/N)w weighted signal-to-noise ratio all standards; unified weighting filter ("ITU-T J.61"); PC at -6 dBFS 57 60 - dB M standard 105 115 127 mV B standard 97 104 116 mV G/H standard 97 104 116 mV D/K standard 89 96 106 mV I standard 93 100 111 mV L standard 89 96 106 mV L-accent standard 89 96 106 mV FM radio (single carrier) 94 103 115 mV M standard; 54 % modulation degree (13.5 kHz FM deviation before pre-emphasis) 98 116 135 mV B, G/H, I, D/K standard; 54 % modulation degree (27 kHz FM deviation before pre-emphasis) 107 126 144 mV M standard; related to 25 kHz peak deviation before pre-emphasis - 7 - dB B, G/H, I, D/K standard; related to 50 kHz peak deviation before pre-emphasis - 7 - dB SSIF/mono sound output Vo(SSIF)(RMS) Vo(AF)(RMS) hr(AF) RMS SSIF output voltage RMS AF output voltage AF headroom TDA8296 Product data sheet 1 k DC or AC load; no modulation; PC / SC1 = 13 dB 1 k DC or AC load before clipping; 1 k DC or AC load All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 4 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 1. Quick reference data ...continued Power supplies 3.3 V, 1.2 V; Tamb = 25 C; PC/SC1 for L and M = 10 dB, all others 13 dB; nominal residual picture carrier of 3 % for L/L' , 10 % for M, 10 % for B/G, 12.5 % for D/K, 20 % for I; FM/AM modulation = 54 %, 1 kHz modulation frequency; measured in application PCB (see Figure 22 and Figure 23) with 16 MHz crystal frequency, terminated with 75 (CVBS) and 1 k (SSIF/audio). Operation mode set via easy programming (Section 9.3.1), otherwise stated. Low IF input signal at -3dB full scale, input frequencies as defined under row header IF input. Symbol Parameter Conditions Min Typ Max Unit THD total harmonic distortion FM; for 50 kHz deviation before pre-emphasis (25 kHz for M standard) - 0.15 0.3 % AM; m = 80 % - 0.5 1 % BAF(-3dB) -3 dB AF bandwidth AM 20 27 - kHz FM 40 50 - kHz via internal mono sound demodulator; "ITU-R BS.468-4"; FM mode related to 27 kHz deviation before pre-emphasis; 10 % residual PC; SC1; color bar picture 52 54 - dB 40 44 - dB (S/N)w(AF) AF weighted signal-to-noise ratio via internal mono sound demodulator; (audio gain +6 dB) "ITU-R BS.468-4"; AM; m = 54 %; 3 % residual PC; SC1; color bar picture [2] [1] The pull-in range can be doubled to 1 660 kHz by I2C-bus register like described in Table 16. Then the AFC read-out has 256 steps. [2] To set audio gain to +6 dB for internal sound demodulation, register 22h has to be programmed to 08h. 5. Ordering information Table 2. Ordering information Type number TDA8296HN TDA8296 Product data sheet Package Name Description Version HVQFN40 plastic thermal enhanced very thin quad flat package; no leads; 40 terminals; body 6 x 6 x 0.85 mm SOT618-1 All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 5 of 87 xxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx x xxxxxxxxxxxxxx xxxxxxxxxx xxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxx xx xxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxx xxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxx xxxxxxxxxxxxxx xxxxxx xx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxx xxxxx x x H/V PLL low IF signal 2 IF ADC FILTERS AND AGC AMPLIFIER PLL DEMODULATOR BIT STREAM DAC VIDEO/ GROUP DELAY EQUALIZER SWITCH UPSAMPLER CORDIC AM/FM SOUND DEMODULATOR CLOCK PROCESSOR AND PLL crystal or frequency reference Functional diagram of TDA8296 SUPPLY, REFERENCE AND DECOUPLING POWER-ON RESET SOUND DAC analog SSIF or mono sound I2C-BUS I2C-bus 008aaa138 TDA8296 6 of 87 (c) NXP B.V. 2011. All rights reserved. Fig 1. VIDEO LOW-PASS FILTER SSIF AND FM RADIO BAND-PASS FILTERS AND AGC PEAK DETECTOR AND INTEGRATOR tuner IF AGC NYQUIST SLOPE Digital global standard low IF demodulator for analog TV and FM radio Rev. 1 -- 3 March 2011 All information provided in this document is subject to legal disclaimers. UPSAMPLER NXP Semiconductors GATED AGC DETECTOR AND INTEGRATOR analog CVBS 6. Functional diagram TDA8296 Product data sheet VIDEO DAC TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 7. Pinning information 31 GPIO2/SDA_O 32 GPIO1/SCL_O 33 GPIO0/VSYNC 34 VDDDR(3V3) 35 VSSDR 36 i.c. 37 IF_AGC 38 i.c. terminal 1 index area 39 n.c. 40 VSSA(ADC) 7.1 Pinning IF_POS 1 30 TRST_N IF_NEG 2 29 SDA VDDA(ADC)(1V2) 3 28 SCL VDDD1(1V2) 4 27 TCK VSSD1 5 i.c. 6 VDDA(PLL)(1V2) 7 24 TMS XIN 8 23 TDI XOUT 9 22 TDO 26 VSSD2 TDA8296HN 25 VDDD2(1V2) SADDR1 20 SADDR0 19 VDDA(DAC2)(3V3) 18 S_IOUTP 17 S_IOUTN 16 VDDA(DAC1)(3V3) 15 V_IOUTP 14 V_IOUTN 13 RSET 11 21 RST_N VSSA(DAC) 12 VSSA(PLL) 10 008aaa139 Transparent top view Fig 2. TDA8296 Product data sheet Pin configuration for HVQFN40 Table 3. Pin allocation table Pin Symbol Pin Symbol 1 IF_POS 2 IF_NEG 3 VDDA(ADC)(1V2) 4 VDDD1(1V2) 5 VSSD1 6 i.c. 7 VDDA(PLL)(1V2) 8 XIN 9 XOUT 10 VSSA(PLL) 11 RSET 12 VSSA(DAC) 13 V_IOUTN 14 V_IOUTP 15 VDDA(DAC1)(3V3) 16 S_IOUTN 17 S_IOUTP 18 VDDA(DAC2)(3V3) 19 SADDR0 20 SADDR1 21 RST_N 22 TDO 23 TDI 24 TMS 25 VDDD2(1V2) 26 VSSD2 27 TCK 28 SCL 29 SDA 30 TRST_N All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 7 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 3. Pin allocation table ...continued Pin Symbol Pin Symbol 31 GPIO2/SDA_O 32 GPIO1/SCL_O 33 GPIO0/VSYNC 34 VDDDR(3V3) 35 VSSDR 36 i.c. 37 IF_AGC 38 i.c. 39 n.c. 40 VSSA(ADC) die pad global ground at backside contact 7.2 Pin description Table 4. Pin description Pin Type[1] Description 21 I The RST_N input is asynchronous and active LOW, and clears the TDA8296. When RST_N goes LOW, the circuit immediately enters its Reset mode and normal operation will resume four XIN signal falling edges later after RST_N returns HIGH. Internal register contents are all initialized to their default values. The minimum width of RST_N at LOW level is four XIN clock periods. XIN 8 I Crystal oscillator input pin. In Slave mode (typically), the XIN input simply receives a 16 MHz clock signal (fREF) from an external device (typically from the TDA1827x). In Oscillator mode, a fundamental 16 MHz (typically) crystal is connected between pin XIN and pin XOUT. XOUT 9 O Crystal oscillator output pin. In Slave mode, the XOUT output is not connected. In Oscillator mode a fundamental 16 MHz (typically) crystal is connected between pin XIN and pin XOUT. SDA 29 I/O, OD I2C-bus bidirectional serial data. SDA is an open-drain output and therefore requires an external pull-up resistor (typically 4.7 k). SCL 28 I I2C-bus clock input. SCL is nominally a square wave with a maximum frequency of 400 kHz. It is generated by the system I2C-bus master. SADDR0 19 I SADDR1 20 I These two bits allow to select four possible I2C-bus addresses, and therefore permits to use several TDA8296 in the same application and/or to avoid conflict with other ICs. The complete I2C-bus address is: 1, 0, 0, SADDR1, 0, 1, SADDR0, R/W (see also Section 9.1). Symbol Reset RST_N Reference I2C-bus I2C-bus feed-through switch or GPIO GPIO2/SDA_O 31 I/O, OD SDA_O is equivalent to SDA but can be 3-stated by I2C-bus programming. It is the output of a switch controlled by I2CSW_EN parameter. SDA_O is an open-drain output and therefore requires an external pull-up resistor (see Section 9.3.18). GPIO1/SCL_O 32 I/O, OD SCL_O is equivalent to SCL input but can be 3-stated by I2C-bus programming. SCL_O is an open-drain output and therefore requires an external pull-up resistor (see Section 9.3.18). For proper functioning of the I2C-bus feed-through, a capacitor C = 33 pF to GND must be added (see Section 13.6). I/O, OD vertical synchronization pulse needed for the NXP Silicon Tuner (see Section 9.3.18) V-sync or GPIO GPIO0/VSYNC 33 Tuner IF AGC IF_AGC 37 TDA8296 Product data sheet I/O, OD, T tuner IF AGC output All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 8 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 4. Pin description ...continued Pin Type[1] Description TMS 24 I Test mode select provides the logic levels needed to change the TAP controller from state to state during the boundary scan test. TRST_N 30 I Test reset is used to reset the TAP controller (active LOW). Grounding is mandatory in Functional mode. TCK 27 I Test clock is used to drive the TAP controller. TDI 23 I Test data input is the serial data input for the test data instruction. TDO 22 O Test data output is the serial test data output pin. The data is provided on the falling edge of TCK. IF_POS 1 AI IF positive analog input for internal ADC IF_NEG 2 AI IF negative analog input for internal ADC V_IOUTP 14 AO positive analog current output of the video output V_IOUTN 13 AO negative analog current output of the video output S_IOUTP 17 AO positive analog current output of the SSIF/mono sound output S_IOUTN 16 AO negative analog current output of the SSIF/mono sound output RSET 11 I External bias setting of the DACs. An external resistor (1 k typical) has to be connected between RSET and the analog ground of the board. This resistor generates the current into the DACs and also defines the full scale output current. The total parasitic capacitance seen externally from the RSET pin has to be lower than 20 pF. VDDA(DAC1)(3V3) 15 PS DAC1 (video DAC) and DAC reference module analog supply voltage (3.3 V typical) VDDA(DAC2)(3V3) 18 PS DAC2 (sound DAC) analog supply voltage (3.3 V typical) VSSA(DAC) 12 GND DAC reference module analog ground supply voltage (0 V typical) VDDA(ADC)(1V2) 3 PS IF ADC analog supply voltage (1.2 V typical) VSSA(ADC) 40 GND ADC analog ground supply voltage (0 V typical) VDDD1(1V2) 4 PS ADC, PLL and DACs digital supply voltage (1.2 V typical) VSSD1 5 GND ADC, PLL and DACs digital ground supply voltage (0 V typical) VDDA(PLL)(1V2) 7 PS crystal oscillator and clock PLL analog supply voltage (1.2 V typical) VSSA(PLL) 10 GND crystal oscillator and clock PLL analog ground supply voltage (0 V typical) VDDD2(1V2) 25 PS core digital supply voltage (1.2 V typical) VSSD2 26 GND core digital ground supply voltage (0 V typical) VDDDR(3V3) 34 PS ring digital supply voltage (3.3 V typical) VSSDR 35 GND ring digital ground supply voltage (0 V typical) VSS die pad GND i.c. 6, 36, 38 I internally connected; connect to ground n.c. 39 I not connected Symbol Boundary scan ADC DAC Supplies and grounds Other pins [1] The pin types are defined in Table 5. TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 9 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 5. Pin type description Type Description AI analog input AO analog output GND ground I digital input I/O digital input and output O digital output OD open-drain output PS power supply T 3-state 8. Functional description 8.1 IF ADC The low IF spectrum (1 MHz to 10 MHz) from the Silicon Tuner TDA1827x is fed symmetrically to the 12-bit IF ADC of the TDA8296, where it is sampled with 54 MHz or 27 MHz. All the anti-aliasing filtering is already done in the Silicon Tuner. 8.2 Filters The internal filters permit to reduce the sampling rate to 13.5 MHz, and to form a complex signal to ease the effort of further signal processing. Before this, the DC offset (coming from the ADC) is removed. In addition, standard dependent notch filters for the adjacent sound carriers protect the picture carrier PLL from malfunctioning and avoid disturbances (i.e. moire) becoming visible in the video output. 8.3 PLL demodulator The second-order PLL is the core block of the whole IC. It is very robust against adverse field conditions, like excessive over modulation, no residual carrier presence or unwanted phase or frequency modulation of the picture carrier. The PLL output is the synchronously demodulated channel. The AFC data is available via the I2C-bus. 8.4 Nyquist filter, video low-pass filter, video and group delay equalizer, video leveling The afore-mentioned down-mixed complex signal at the mixer CORDIC output, already consisting of the demodulated content of the picture carrier together with the sound carriers (the so-called intercarriers), is running through a Nyquist filter to get a flat video response and is made real. Afterwards, a video low-pass filter suppresses the sound carriers and other disturbers. Next comes the equalizer circuit to remove the transmitter group delay predistortion. TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 10 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio A video leveling stage follows, which brings the output within the SCART specification (3 dB overall), despite heavy over modulation. The response time is made very slow. Finally, a video equalizer allows to compensate the perhaps non-flat frequency response from the tuner or to change the overall video response according to customer wish (i.e. peaking or early roll-off). 8.5 Upsampler and video DAC The filtered and compensated CVBS signal is connected to the oversampled 10-bit video DAC (fs = 108 MHz) via an interpolation stage. The strong oversampling replaces a former complicated LCR postfiltering by a simple first-order RC low-pass filter to remove the DAC image frequencies sufficiently. This holds also for the sound DAC, described in Section 8.6. 8.6 SSIF/mono sound processing The complex signal is routed via a band-pass, AGC and interpolation filter to the 10-bit sound DAC for the recovery of the second sound carriers (SSIF). A very sharp band-pass filter at 5.5 MHz is added in the FM Radio mode to remove neighbor channels. This also eases the dynamic burden on the following ADC in the demodulator/decoder chip. The afore-mentioned high-selectivity band-pass, which replaces the former ceramic filter, is located behind a frequency shifter. In there, the incoming wanted FM radio channel from the Silicon Tuner is changed from 1.25 MHz to 5.5 MHz. Moreover, the complex signal is demodulated in a linear CORDIC detector and low-pass filtered to attenuate the video spectrum and the second sound carrier, respectively other disturbers above the intercarrier. The output of the linear CORDIC (phase information) is differentiated for getting the demodulated FM audio. The AM demodulation is executed in a synchronous fashion by using a narrow-band PLL demodulator. A de-emphasis filter is implemented for FM standards, before the audio is interpolated to 108 MHz as in the CVBS case. The mono audio is made available in the sound DAC via an I2C-bus controlled selector in case the intercarrier path is not used for driving an external stereo demodulator. However, if the mono audio output has to meet the SCART specification, an external cheap operational amplifier with 12 dB gain becomes necessary, because the low supply voltage for the TDA8296 doesn't allow such high levels like 2 V (RMS) maximum. 8.7 Tuner IF AGC This AGC controls the tuner IF AGC amplifier in the TDA1827x in such a way, that the IF ADC is always running with a permanent headroom of 3 dB for the sum of all signals present at the ADC input. This ensures an always optimal exploitation of the dynamic range in the IF ADC. The detection is done in peak Search mode during a field period. The attack time is made much faster than the decay time in order to avoid transient clipping effects in the IF ADC. This can happen during channel change or airplane flutter conditions. TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 11 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio The above wideband, slowly acting AGC loop (uncorrelated) is of first-order integral action. It is closed via the continuous tuner IF AGC amplifier in the Silicon Tuner via a bit stream DAC (PWM signal at 13.5 MHz, 27 MHz or 54 MHz) and an external and uncritical first-order RC low-pass. 8.8 Digital IF AGC Common to both IF AGC concepts is the peak search algorithm as long as the H/V PLL is not locked. This is of advantage for the acquisition by avoiding hang-ups due to excessive overloading, so being able to leave the saturated condition by reducing the gain. Two Detection modes are made available in the IC via I2C-bus. * Black level gated AGC: The first mode uses an IF AGC detector which is gated with a very robust and well-proven H/V sync PLL block on board. Gating occurs on the black level (most of the time on the back porch) of the video signal and the control is delivered after an error integration and exponential weighting to the internal IF AGC amplifier. This IF AGC amplifier, in fact a multiplier, has a control range of -20 dB to +48 dB. * Peak AGC: A fast attack and slow decay action cares for a good and nearly clip-free transient behavior. This proved to be more robust for non-standard signals, like sync clipping along the transmitter/receiver chain. With respect to the IF AGC speed generally, only the gated black level or peak sync digital IF AGC can be made fast. However the peak search tuner IF AGC, used for positive modulation standards (L and L-accent standard), is rather slow because the VITS is present only once in a field. The correlated or narrow-band AGC loop, closed via the continuous IF AGC amplifier in the TDA8296, is of first-order integral action and settles at a constant IF input level with a permanent headroom of 12 dB (picture carrier). This headroom is needed for the own sound carriers and the leaking neighbor (N - 1) spectrum. 8.9 Clock generation Finally, either an external reference frequency (i.e. from the Silicon Tuner) or an own on-chip crystal oscillator in the TDA8296 feeds the internal PLL synthesizer to generate the necessary clock signals. 9. I2C-bus control 9.1 Protocol of the I2C-bus serial interface The TDA8296 internal registers are accessible by means of the I2C-bus serial interface. The SDA bidirectional pin is used as the data input/output pin and SCL as the clock input pin. The highest SCL speed is 400 kHz. TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 12 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 9.1.1 Write mode S BYTE 1 A BYTE 2 A BYTE 3 A start address 0 ack start index ack data 1 ack BYTE n A data n ack .... P stop 001aad381 Fig 3. I2C-bus Write mode Table 6. Address format 7 6 5 4 3 2 1 0 1 0 0 SADDR1 0 1 SADDR0 R/W Table 7. I2C-bus transfer description Field Bit Description S - START condition Byte 1 7 to 5 device address 4 SADDR1 3 and 2 device address 1 SADDR0 0 R/W = 0 for write action A - acknowledge Byte 2 7 to 0 start index A - acknowledge Byte 3 7 to 0 data 1 A - acknowledge Byte n 7 to 0 data n A - acknowledge P - STOP condition : S BYTE 1 A BYTE 2 A BYTE 3 A P start 1000 0100 ack 0000 0001 ack 0000 0010 ack stop 001aah355 a. Address 84h, write 02h in register 01h S BYTE 1 A BYTE 2 A BYTE 3 A BYTE 4 A P start 1000 0100 ack 0000 0010 ack 0000 0101 ack 0000 0100 ack stop 001aah356 b. Address 84h, write 05h in register 02h and 04h in register 03h Fig 4. TDA8296 Product data sheet Examples I2C-bus Write mode All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 13 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 9.1.2 Read mode S BYTE 1 A BYTE 2 A S BYTE 3 A BYTE 4 A start address 0 ack start index ack start address 1 ack value 1 ack .... BYTE n A value n ack P stop 001aad423 Fig 5. Table 8. I2C-bus Read mode I2C-bus transfer description Field Bit Description S - START condition Byte 1 7 to 5 device address 4 SADDR1 3 and 2 device address 1 SADDR0 0 R/W = 0 for write action A - acknowledge Byte 2 7 to 0 start index A - acknowledge S - START condition (without stop before) Byte 3 7 to 5 device address 4 SADDR1 3 and 2 device address 1 SADDR0 0 R/W = 1 for read action A - acknowledge Byte 4 7 to 0 value 1 A - acknowledge Byte n 7 to 0 value n A - acknowledge P - STOP condition : S BYTE 1 A BYTE 2 A S BYTE 3 A BYTE 4 A BYTE 5 A P start 1000 0100 ack 0000 0010 ack start 1000 0101 ack 0000 0101 ack 0000 0100 ack stop 001aah357 Address 84h, read register 02h with value 05h and read register 03h with value 04h Fig 6. Example I2C-bus Read mode TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 14 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 9.2 Register overview The TDA8296 internal registers are accessible by means of the I2C-bus serial interface as described in Section 9.1. In Table 10 and Table 9 an overview of all the registers is given, the register description can be found in Section 9.3. Table 9. Index Name I2C-bus access Default value Reference 00h STANDARD R/W 01h Table 11 01h EASY_PROG R/W 00h Table 12 02h DIV_FUNC R/W 04h Table 14 03h ADC_HEADR R/W 01h Table 15 04h PC_PLL_FUNC R/W 24h Table 16 05h SSIF_MUTE R/W 04h Table 33 06h reserved R/W 48h[1] - R/W 84h[1] - 07h TDA8296 Product data sheet I2C-bus register reference reserved 08h reserved R/W 08h[1] 09h DTO_PC_LOW R/W 9Ah Table 17 0Ah DTO_PC_MID R/W 99h Table 17 0Bh DTO_PC_HIGH R/W 99h Table 17 0Ch DTO_SC_LOW R/W 3Dh Table 19 0Dh DTO_SC_MID R/W 20h Table 19 0Eh DTO_SC_HIGH R/W 59h Table 19 0Fh FILTERS_1 R/W 21h Table 21 10h FILTERS_2 R/W 31h Table 22 11h GRP_DELAY R/W 01h Table 23 12h D_IF_AGC_SET_1 R/W A0h Table 24 13h D_IF_AGC_SET_2 R/W 90h Table 25 - 14h reserved R/W 67h[1] 15h T_IF_AGC_SET R/W 88h Table 26 16h T_IF_AGC_LIM R/W F0h Table 27 17h T_IF_AGC_FORCE R/W 3Fh Table 28 - 18h reserved R/W 02h[1] 19h reserved R/W 88h[1] - 1Ah reserved R/W 80h[1] - 1Bh reserved R/W 00h[1] 1Ch V_SYNC_DEL R/W 6Fh Table 29 1Dh CVBS_SET R/W 31h Table 30 1Eh CVBS_LEVEL R/W 73h Table 31 1Fh CVBS_EQ R/W 10h Table 32 20h SOUNDSET_1 R/W 21h Table 34 21h SOUNDSET_2 R/W 22h Table 35 22h SOUND_LEVEL R/W 08h Table 36 23h SSIF_LEVEL R/W AFh Table 37 All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 15 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 9. Index Name I2C-bus access Default value Reference 24h ADC_SAT R - Table 38 25h AFC R - Table 39 26h HVPLL_STAT R - Table 41 27h D_IF_AGC_STAT R - Table 42 28h T_IF_AGC_STAT R - Table 43 29h reserved R - - R/W 00h[1] Table 44 2Ah TDA8296 Product data sheet I2C-bus register reference ...continued reserved 2Bh ALT_FILT_COEF R/W 00h[1] 2Ch reserved R - - 2Dh SSIF_AGC_STAT_REG R - Table 45 2Eh not used R/W 00h - 2Fh IDENTITY R - Table 46 30h CLB_STDBY R/W 01h Table 47 - 31h reserved R/W 00h[1] 32h reserved R - - 33h ADC_CTL R/W 24h Table 48 34h ADC_CTL_2 R/W 05h Table 49 35h VIDEODAC_CTL R/W 7Eh Table 50 36h AUDIODAC_CTL R/W 00h Table 51 37h DAC_REF_CLK_CTL R/W 40h Table 52 38h reserved R/W 20h[1] - 39h to 3Bh not used R/W 00h - 3Ch reserved R/W 00h[1] 3Dh not used R/W 00h - 3Eh reserved R/W 61h[1] - 3Fh PLL_REG07 R/W 00h Table 53 40h PLL_REG08 R/W 1Ah Table 53 41h PLL_REG09 R/W 02h Table 53 42h PLL_REG10 R/W 01h Table 53 - 43h reserved R/W 00h[1] 44h GPIOREG_0 R/W 1Bh Table 54 45h GPIOREG_1 R/W C1h Table 55 46h GPIOREG_2 R/W 07h Table 57 47h to 4Ah reserved R - - 4Bh GD_EQ_SECT1_C1 R/W 00h Table 58 4Ch GD_EQ_SECT1_C2 R/W 00h Table 58 4Dh GD_EQ_SECT2_C1 R/W 00h Table 58 4Eh GD_EQ_SECT2_C2 R/W 00h Table 58 4Fh GD_EQ_SECT3_C1 R/W 00h Table 58 50h GD_EQ_SECT3_C2 R/W 00h Table 58 51h GD_EQ_SECT4_C1 R/W 00h Table 58 All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 16 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 9. I2C-bus register reference ...continued Index Name I2C-bus access Default value Reference 52h GD_EQ_SECT4_C2 R/W 00h Table 58 53h to 56h not used R/W 00h - 57h CVBS_EQ_COEF0_LOW R/W 00h Table 60 58h CVBS_EQ_COEF0_HIGH R/W 00h Table 60 59h CVBS_EQ_COEF1_LOW R/W 00h Table 60 5Ah CVBS_EQ_COEF1_HIGH R/W 00h Table 60 5Bh CVBS_EQ_COEF2_LOW R/W 00h Table 60 5Ch CVBS_EQ_COEF2_HIGH R/W 00h Table 60 5Dh CVBS_EQ_COEF3_LOW R/W 00h Table 60 5Eh CVBS_EQ_COEF3_HIGH R/W 00h Table 60 5Fh CVBS_EQ_COEF4_LOW R/W 00h Table 60 60h CVBS_EQ_COEF4_HIGH R/W 00h Table 60 61h CVBS_EQ_COEF5_LOW R/W 00h Table 60 62h CVBS_EQ_COEF5_HIGH R/W 04h Table 60 63h to 66h not used R/W 00h - 67h reserved R/W FEh[1] 68h reserved R/W 0Fh[1] - R/W FAh[1] - R/W 0Fh[1] - 69h reserved 6Ah reserved 6Bh reserved R/W EFh[1] 6Ch reserved R/W 0Fh[1] - R/W DDh[1] - R/W 0Fh[1] - 6Dh 6Eh reserved 6Fh reserved R/W BEh[1] 70h reserved R/W 0Fh[1] - R/W 8Ah[1] - R/W 0Fh[1] - 71h reserved 72h reserved 73h reserved R/W 32h[1] 74h reserved R/W 0Fh[1] - R/W 6Fh[1] - R/W 0Eh[1] - 75h reserved 76h Product data sheet reserved 77h reserved R/W F4h[1] 78h reserved R/W 0Ah[1] - 79h to 7Bh not used R/W 00h - 7Ch to 9Ch reserved R/W 00h[1] 9Dh to A0h not used R/W 00h - A1h and A2h reserved R/W 00h[1] - [1] TDA8296 reserved This register must not be written with values other than default. All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 17 of 87 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx NXP Semiconductors TDA8296 Product data sheet Table 10. I2C-bus registers Index Name 7 (MSB) 4 3 2 1 0 (LSB) 00h STANDARD STANDARD[7:0] 01h EASY_PROG 0 0 0 0 0 0 0 ACTIVE 02h DIV_FUNC T_IF_SEL[1:0] 0 0 0 POL_DET VID_MOD IF_SWAP 03h ADC_HEADR 0 0 0 0 ADC_HEADR[3:0] 04h PC_PLL_FUNC PC_PLL_BW[4:0] 05h SSIF_MUTE PULL_IN 0 0 0 SSIF_AFC_WIN[3:0] SSIF_MUTE_ TYPE SSIF_MUTE_ CTRL 06h[1] reserved 0 1 0 0 1 0 0 0 07h reserved 1 0 0 0 0 1 0 0 08h reserved 0 0 0 0 1 0 0 0 09h DTO_PC_LOW DTO_PC[7:0] 0Ah DTO_PC_MID DTO_PC[15:8] 0Bh DTO_PC_HIGH DTO_PC[23:16] 0Ch[2] DTO_SC_LOW DTO_SC[7:0] 0Dh[3] DTO_SC_MID DTO_SC[15:8] 0Eh[3] DTO_SC_HIGH DTO_SC[23:16] 0Fh FILTERS_1 VID_FILT[2:0] 10h[4] FILTERS_2 0 0 VID_FILT_ LOW_RIP 1 11h GRP_DELAY GD_EQ_CTRL 0 0 GRP_DEL[4:0] 12h D_IF_AGC_SET_1 1 D_IF_AGC_ MODE 1 0 0 0 0 0 13h D_IF_AGC_SET_2 1 D_IF_AGC_BW[6:0] 14h reserved 0 1 0 1 1 1 1 15h T_IF_AGC_SET POL_TIF T_IF_AGC_SPEED[6:0] 16h T_IF_AGC_LIM UP_LIM[3:0] 17h T_IF_AGC_FORCE T_FORCE T_FORCE_VAL[6:0] 18h reserved 0 0 0 0 0 1 0 0 19h reserved 1 0 0 0 1 0 0 0 1Ah reserved 1 0 0 0 0 0 0 0 1Bh reserved 0 0 0 0 0 0 0 0 PLL_ON NOTCH_FILT[4:0] 1 SBP[3:0] LOW_LIM[3:0] TDA8296 18 of 87 (c) NXP B.V. 2011. All rights reserved. 5 Digital global standard low IF demodulator for analog TV and FM radio Rev. 1 -- 3 March 2011 All information provided in this document is subject to legal disclaimers. 6 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx I2C-bus registers ...continued Index Name 7 (MSB) 1Ch V_SYNC_DEL 6 5 4 VS_WIDTH[1:0] VS_POL VS_DEL[4:0] 1[5] 1 0 3 2 1 0 (LSB) CVBS_EQ_ CTRL FOR_BLK AUTO_BLK 1 FOR_MUTE AUTO_ MUTE SSIF_SND[1:0] 0 1Eh CVBS_LEVEL CVBS_LVL[7:0] 1Fh CVBS_EQ CVBS_EQ[7:0] 20h SOUNDSET_1 0 AM_FM_SND[1:0] DEEMPH[4:0] 21h SOUNDSET_2 0 SSIF_AGC_ TC SSIF_AGC_ CTRL HD_DK 22h SOUND_LEVEL 0 0 0 SND_LVL[4:0] 23h SSIF_LEVEL SSIF_LVL[7:0] 24h ADC_SAT ADC_SAT[7:0] 25h AFC AFC[7:0] 26h HVPLL_STAT - - NOISE_DET MAC_DET FIDT V_LOCK F_H_LOCK N_H_LOCK 27h D_IF_AGC_STAT D_IF_AGC_STAT[7:0] 28h T_IF_AGC_STAT T_IF_AGC_STAT[7:0] 29h reserved - - - - - - - - 2Ah reserved 0 0 0 0 0 0 0 0 2Bh ALT_FILT_COEF[6] 0 0 0 0 0 0 ALT_FILT_COEF[1:0] 2Ch reserved - - - - - - - - 2Dh SSIF_AGC_STAT SSIF_AGC_STAT[7:0] 2Eh not used 0 0 0 0 0 0 0 0 2Fh IDENTITY IDENTITY[7:0] 30h CLB_STDBY 0 0 0 0 0 0 STDBY CLB 31h reserved 0 0 0 0 0 0 0 0 32h reserved - - - - - - - - 33h ADC_CTL 0 0 1 0 DCIN 1 SLEEP PD_ADC 34h ADC_CTL_2 0 0 0 0 0 1 0 AD_SR54M 35h VIDEODAC_CTL 0 B_DA_V[5:0] PD_DA_V 36h AUDIODAC_CTL 0 B_DA_S[5:0] PD_DA_S 37h DAC_REF_CLK_CTL 0 1 0 0 0 0 0 PD_DA_REF TDA8296 19 of 87 (c) NXP B.V. 2011. All rights reserved. CVBS_SET Digital global standard low IF demodulator for analog TV and FM radio Rev. 1 -- 3 March 2011 All information provided in this document is subject to legal disclaimers. 1Dh NXP Semiconductors TDA8296 Product data sheet Table 10. xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx I2C-bus registers ...continued 7 (MSB) 6 5 4 3 2 1 0 (LSB) 38h reserved[6] 0 0 1 0 0 0 0 0 39h to 3Bh not used 0 0 0 0 0 0 0 0 3Ch reserved 0 0 0 0 0 0 0 0 3Dh not used 0 0 0 0 0 0 0 0 3Eh reserved[6] 0 1 1 0 0 0 0 1 3Fh PLL_REG07[6] 0 NSEL7 0 0 0 0 0 0 40h PLL_REG08[6] MSEL[7:0] 41h PLL_REG09[6] NSEL[6:0] 42h PLL_REG10[6] 0 0 0 PSEL[4:0] 43h reserved 0 0 0 0 44h GPIOREG_0 GP1_CF[3:0] 45h GPIOREG_1 I2CSW_EN I2CSW_ON 0 0 GP2_CF[3:0] 46h GPIOREG_2 0 0 0 0 47h to 4Ah reserved - - - 4Bh GD_EQ_SECT1_C1 GD_EQ_SECT1_C1[7:0] 4Ch GD_EQ_SECT1_C2 GD_EQ_SECT1_C2[7:0] 4Dh GD_EQ_SECT2_C1 GD_EQ_SECT2_C1[7:0] 4Eh GD_EQ_SECT2_C2 GD_EQ_SECT2_C2[7:0] 4Fh GD_EQ_SECT3_C1 GD_EQ_SECT3_C1[7:0] 50h GD_EQ_SECT3_C2 GD_EQ_SECT3_C2[7:0] 51h GD_EQ_SECT4_C1 GD_EQ_SECT4_C1[7:0] 52h GD_EQ_SECT4_C2 GD_EQ_SECT4_C2[7:0] 53h to 56h not used 0 57h CVBS_EQ_COEF0_ LOW CVBS_EQ_COEF0[7:0] 58h CVBS_EQ_COEF0_ HIGH 0 59h CVBS_EQ_COEF1_ LOW CVBS_EQ_COEF1[7:0] 0 0 0 0 0 0 GP2_VAL GP1_VAL GP0_VAL - - - - - 0 0 0 0 0 0 0 0 CVBS_EQ_COEF0[11:8] GP0_CF[3:0] 0 0 TDA8296 20 of 87 (c) NXP B.V. 2011. All rights reserved. Name Digital global standard low IF demodulator for analog TV and FM radio Rev. 1 -- 3 March 2011 All information provided in this document is subject to legal disclaimers. Index NXP Semiconductors TDA8296 Product data sheet Table 10. xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx I2C-bus registers ...continued Name 7 (MSB) 6 5 4 3 0 (LSB) 5Ah CVBS_EQ_COEF1_ HIGH 0 0 0 0 CVBS_EQ_COEF1[11:8] 5Bh CVBS_EQ_COEF2_ LOW CVBS_EQ_COEF2[7:0] 5Ch CVBS_EQ_COEF2_ HIGH 0 0 0 CVBS_EQ_COEF2[11:8] 5Dh CVBS_EQ_COEF3_ LOW CVBS_EQ_COEF3[7:0] 5Eh CVBS_EQ_COEF3_ HIGH 0 0 0 CVBS_EQ_COEF3[11:8] 5Fh CVBS_EQ_COEF4_ LOW CVBS_EQ_COEF4[7:0] 60h CVBS_EQ_COEF4_ HIGH 0 0 0 CVBS_EQ_COEF4[11:8] 61h CVBS_EQ_COEF5_ LOW CVBS_EQ_COEF5[7:0] 62h CVBS_EQ_COEF5_ HIGH 0 0 0 0 CVBS_EQ_COEF5[11:8] 63h to 66h not used 0 0 0 0 0 0 0 0 67h reserved 1 1 1 1 1 1 1 0 68h reserved 0 0 0 0 1 1 1 1 69h reserved 1 1 6Ah reserved 0 0 1 1 1 0 1 0 0 0 1 1 1 1 6Bh reserved 1 1 1 0 1 1 1 1 6Ch reserved 0 0 0 0 1 1 1 1 6Dh 6Eh reserved 1 1 0 1 1 1 0 1 reserved 0 0 0 0 1 1 1 1 6Fh reserved 1 0 1 1 1 1 1 0 70h reserved 0 0 0 0 1 1 1 1 71h reserved 1 0 0 0 1 0 1 0 72h reserved 0 0 0 0 1 1 1 1 73h reserved 0 0 1 1 0 0 1 0 0 0 TDA8296 21 of 87 (c) NXP B.V. 2011. All rights reserved. 1 0 2 Digital global standard low IF demodulator for analog TV and FM radio Rev. 1 -- 3 March 2011 All information provided in this document is subject to legal disclaimers. Index NXP Semiconductors TDA8296 Product data sheet Table 10. xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx I2C-bus registers ...continued Name 7 (MSB) 6 5 4 3 2 1 0 (LSB) 74h reserved 0 0 0 0 1 1 1 1 75h reserved 0 1 1 0 1 1 1 1 76h reserved 0 0 0 0 1 1 1 0 77h reserved 1 1 1 1 0 1 0 0 78h reserved 0 0 0 0 1 0 1 0 79h to 7Bh not used 0 0 0 0 0 0 0 0 7Ch to reserved 9Ch 0 0 0 0 0 0 0 0 9Dh to not used A0h 0 0 0 0 0 0 0 0 A1h and A2h 0 0 0 0 0 0 0 0 reserved [1] Register 06h has to be reprogrammed to new value C4h. [2] Register 0Ch has to be reprogrammed to new value 00h. [3] For M/N standard (ADC clock at 54 MHz) register 0Dh and 0Eh have to be reprogrammed to new value 55h. [4] For M/N standard use narrow SSIF band-pass filter (SBP[3:0] = 0100). [5] For L/L-accent standard the bit has to be programmed to 0. [6] These registers have to be programmed to the alternative value in Table 66, if an other frequency is required than 54 MHz for ADC sample frequency. TDA8296 22 of 87 (c) NXP B.V. 2011. All rights reserved. Digital global standard low IF demodulator for analog TV and FM radio Rev. 1 -- 3 March 2011 All information provided in this document is subject to legal disclaimers. Index NXP Semiconductors TDA8296 Product data sheet Table 10. TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 9.3 Register description If registers (or bit groups contained in registers) are programmed with invalid values, i.e. values different from those described in the tables below, the default behavior is chosen for the related block. Other settings than described in the tables are not allowed. 9.3.1 Standard setting with easy programming With the implemented `easy programming', only one bit sets the TV or FM radio standard with recommended register content. If not suitable however, any of these registers can be written with other settings. With the rising edge of the bit ACTIVE, some of the registers 02h to 23h are programmed internally with the standard dependent settings according to Table 13. The content of registers with address 24h and higher is untouched. Table 11. STANDARD register (address 00h) bit description Legend: * = default value. Bit Symbol Access Value 7 to 0 STANDARD[7:0 R/W ] Description TV or FM radio standard selection (easy programming) 0000 0001* M/N standard 0000 0010 B standard 0000 0100 G/H standard 0000 1000 I standard 0001 0000 D/K standard 0010 0000 L standard 0100 0000 L-accent standard 1000 0000 FM radio In addition to application specific software settings following general recommendation should be used (deviating from easy programming values): * Register 06h: new value C4h * Register 0Ch: new value 00h * M/N standard: - Register 10h: use narrow SSIF band-pass filter (SBP[3:0] = 0100) - Register 0Dh and 0Eh: new value 55h Remark: When using alternative ADC sampling frequencies the DTO settings have to be adapted accordingly. Table 12. EASY_PROG register (address 01h) bit description Legend: * = default value. Bit TDA8296 Product data sheet Symbol Access Value Description 7 to 1 - R/W not used 0 R/W ACTIVE 000 0000* With the rising edge of this bit, the registers 02h to 23h are programmed with the standard dependent settings (see Table 13). 0* no action 1 no action 0 to 1 activate easy programming All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 23 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Example: To set the device to B standard e.g., please do the following steps. 1. Write 02h to register STANDARD, address 00h (set B standard) 2. Write 00h to register EASY_PROG, address 01h 3. Write 01h to register EASY_PROG, address 01h (due to 0 to 1 transition of ACTIVE the device is set to B standard, i.e. registers 02h to 23h are programmed automatically according to Table 13) 4. Write 00h to register EASY_PROG, address 01h (reset ACTIVE to logic 0) Table 13. Easy programming values Register Standard Index Name M/N[1] B G/H I D/K L L-accent FM radio 02h DIV_FUNC 04h 04h 04h 04h 04h 06h 07h 00h 04h PC_PLL_FUNC 24h 24h 24h 24h 24h 24h 24h 20h 05h SSIF_MUTE 04h 04h 04h 04h 04h 04h 04h 04h 06h reserved 48h 48h 48h 48h 48h 48h 48h 48h 07h reserved 84h 84h 84h 84h 84h 84h 84h 04h 08h reserved 08h 08h 08h 08h 08h 08h 08h 08h 09h DTO_PC_LOW 9Ah 15h 00h BEh 8Ch 00h 26h 00h 0Ah DTO_PC_MID 99h A3h 00h 84h 1Ah 00h B4h 00h 0Bh DTO_PC_HIGH 99h 86h 80h 76h 7Eh 80h 17h 80h 0Ch DTO_SC_LOW 3Dh 7Bh 7Bh BEh BEh D6h D6h DAh 0Dh DTO_SC_MID 20h 09h 09h 84h 84h B9h B9h 4Bh 0Eh DTO_SC_HIGH 59h 6Dh 6Dh 76h 79h 72h 72h 68h 0Fh FILTERS_1 21h 42h 48h 48h 44h 44h 48h 90h 10h FILTERS_2 31h 32h 32h 32h 32h 32h 32h 34h 11h GRP_DELAY 01h 02h 02h 10h 04h 08h 08h 10h 12h D_IF_AGC_SET_1 A0h A0h A0h A0h A0h A0h A0h A0h 13h D_IF_AGC_SET_2 90h 90h 90h 90h 90h 90h 90h 08h 14h reserved 67h 67h 67h 67h 67h 67h 67h E7h 1Dh CVBS_SET 31h 31h 31h 31h 31h 31h 31h 04h 1Eh CVBS_LEVEL 73h 73h 73h 81h 75h 6Ch 6Ch 73h 1Fh CVBS_EQ 10h 10h 10h 10h 10h 10h 10h 10h 20h SOUNDSET_1 21h 22h 22h 22h 22h 44h 44h 22h 21h SOUNDSET_2 22h 22h 22h 22h 22h 22h 22h 22h 22h SOUND_LEVEL 08h 04h 04h 04h 04h 04h 04h 02h 23h SSIF_LEVEL AFh AFh AFh AFh AFh AFh AFh AFh [1] M/N standard settings are equal to the power-on reset (default) values. TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 24 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 9.3.2 Diverse functions (includes tuner IF AGC Pin mode) Table 14. DIV_FUNC register (address 02h) bit description Legend: * = default value. Bit Symbol Access Value Description 7 and 6 T_IF_SEL[1:0] R/W It determines the tuner IF AGC output Pin mode. The open-drain output can be used in special applications in need of a higher control voltage. 00* Normal mode 01 Open-drain mode 10 3-state mode 11 not allowed 5 and 4 - R/W 00* not used 3 - R/W 0* reserved, must be set to logic 0 2 POL_DET R/W 1 VID_MOD 0 IF_SWAP The polarity detector ensures the proper polarity of the video signal. So, the sync impulses of the video output are near ground level. 0 polarity detector off 1* polarity detector on R/W Selects video modulation. The only standards with positive video modulation are L and L-accent. 0* negative video modulation 1 positive video modulation R/W When HIGH, the demodulator expects a swapped IF spectrum. This is the case in L-accent standard. This option is also built in for flexibility reasons. 0* normal IF spectrum expected 1 swapped IF spectrum expected 9.3.3 ADC headroom Table 15. ADC_HEADR register (address 03h) bit description Legend: * = default value. Bit Symbol 7 to 4 - Access Value Description R/W 0000* not used 3 to 0 ADC_HEADR[3:0] R/W TDA8296 Product data sheet ADC_HEADR adjusts the needed headroom for the wanted channel's own sound carriers and the N - 1 adjacent sound carriers (PC in L-accent standard). The ADC headroom is related to the sum of all signals. This function is built in for debugging purposes. 0001* ADC headroom 3 dB 0010 ADC headroom 6 dB 0100 ADC headroom 9 dB 1000 ADC headroom 12 dB All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 25 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 9.3.4 Picture carrier PLL functions Table 16. PC_PLL_FUNC register (address 04h) bit description Legend: * = default value. Bit Symbol Access 7 to 3 PC_PLL_BW[4:0] R/W 2 PLL_ON 1 picture carrier PLL loop bandwidth selection loop bandwidth 15 kHz (not recommanded) 0 0010 loop bandwidth 30 kHz 0 0100* loop bandwidth 60 kHz 0 1000 loop bandwidth 130 kHz 1 0000 loop bandwidth 280 kHz (not recommanded) the picture carrier PLL can be disengaged (e.g. in FM radio standard) 0 PLL off (FM radio)[1] 1* PLL on[2] R/W - Description 0 0001 R/W PULL_IN 0 Value PULL_IN selects the pull-in range of the picture carrier PLL/FPLL R/W 0* pull-in range 1.66 MHz 1 pull-in range 830 kHz 0* [1] The DTO_PC frequency is set via register 09h to 0Bh [2] The DTO_PC frequency is controlled by VIF_PLL function reserved, must be set to logic 0 9.3.5 Picture and sound carrier DTO Table 17. DTO_PC_LOW, DTO_PC_MID and DTO_PC_HIGH register (address 09h to 0Bh) bit description Legend: * = default value. Address Register Bit Symbol Access Value Description For picture processing the digital tuned oscillator (DTO_PC) provides its oscillation signal to the demodulator part. For demodulation the oscillation frequency of the DTO_PC is controlled by the VIF_PLL. Optional the DTO_PC can operate at fixed programmed frequency. This will be the case if PLL_ON register is set to "off" mode. In case of VIF_PLL mode of the DTO_PC the register value defines the nominal frequency of AFC register (seeTable 39). If PLL_ON register is set to "off" mode the DTO_PC register defines the fixed oscillation frequency value of the DTO_PC. The frequency of the DTO_PC is in relation to the register value by following formula: 09h DTO_PC_LOW 7 to 0 DTO_PC[7:0] R/W 9Ah* 0Ah DTO_PC_MID R/W 99h* 0Bh DTO_PC_HIGH 7 to 0 DTO_PC[23:16] R/W 99h* 7 to 0 DTO_PC[15:8] f ADC 4 - f PC 24 DTO_PC = --------------------------------- x 2 f ADC 4 . In case of standard L' please use the following formula: TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 4 24 DTO_PC = f PC x ----------- x 2 f ADC (c) NXP B.V. 2011. All rights reserved. 26 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 001aan388 10 DTO_PC frequency value (MHz) 8 (2) 6 4 2 (1) 0 0 4 8 12 DTO_PC reg val (dec) (1E6) (1) relation for L' (2) relation for systems L; M/N; B/G; I; D/K Fig 7. Table 18. TDA8296 DTO_PC characteristic Values of DTO_PC per TV standard at 54 MHz sampling frequency Standard DTO_SC[23:16] DTO_SC[15:8] DTO_SC[7:0] DTO_PC frequency value M/N 99h 99h 9Ah 5.40 MHz B 86h A3h 15h 6.40 MHz G 80h 00h 00h 6.75 MHz I 76h 84h BEh 7.25 MHz D/K 7Eh 1Ah 8Ch 6.85 MHz L 80h 00h 00h 6.75 MHz L-accent 17h B4h 26h 1.25 MHz Table 19. DTO_SC_LOW, DTO_SC_MID and DTO_SC_HIGH register (address 0Ch to 0Eh) bit description Legend: * = default value.[1] Address Register Bit Symbol Access Value Description The DTO_SC is suited for SSIF band-pass filter tuning. DTO_SC is calculated according to the following formula, whereas fSC is the SSIF band-pass center frequency: 0Ch DTO_SC_LOW 7 to 0 DTO_SC[7:0] R/W 00h* 0Dh DTO_SC_MID R/W 20h* 0Eh DTO_SC_HIGH 7 to 0 DTO_SC[23:16] R/W 59h* 7 to 0 DTO_SC[15:8] f SC 24 DTO_SC = ------------------ x 2 . f ADC 4 [1] Deviating from easy programming values for DTO_SC[23:0] the values from Table 20 should be used. TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 27 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 001aam354 10 Fsc [MHz] 8 6 4 2 0 0 4 8 12 DTO reg val (dec) (1E6) Fig 8. Table 20. TDA8296 DTO_SC characteristic Values for SSIF mode at 54 MHz sampling frequency Standard DTO_SC[23:16] DTO_SC[15:8] DTO_SC[7:0] Band-pass center frequency M/N 55h 55h 00h 4.5 MHz B 6Dh 09h 00h 5.75 MHz G/H 6Dh 09h 00h 5.75 MHz I 76h 84h 00h 6.25 MHz D/K 76h 84h 00h 6.25 MHz L/L-accent 72h B9h 00h 6.05 MHz FM radio 68h 4Bh 00h 5.5 MHz 9.3.6 Filter settings Table 21. FILTERS_1 register (address 0Fh) bit description Legend: * = default value. Bit Symbol Access 7 to 5 VID_FILT[2:0] R/W 4 to 0 NOTCH_FILT[4:0] TDA8296 Product data sheet Value Description video low-pass filter to remove all unwanted frequencies (own sound carriers) above video content (see Figure 9) 001* video low-pass filter 4 MHz 010 video low-pass filter 5 MHz 100 video low-pass filter off The notch filter attenuates the adjacent sound carrier N - 1, which is located differently dependent on standard (see Figure 10). R/W 0 0001* notch filter at 6.9 MHz for M/N standard 0 0010 notch filter at 7.9 MHz for B standard 0 0100 notch filter at 8.3 MHz for D/K and L standard 0 1000 notch filter at 9.25 MHz for G/H, I and L-accent standard 1 0000 notch filter bypass All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 28 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 008aaa223 10 resp(f) (dB) -10 (1) (2) -30 -50 -70 0 1 2 3 4 5 6 7 f (MHz) (1) M/N standard. (2) All other standards. Fig 9. Video low-pass filters for sound carrier suppression 008aaa224 10 resp(f) (dB) (1) (2) (3) (4) -10 -30 -50 -70 0 2 4 6 8 10 12 14 f (MHz) Notch filter for NSC (NPC for L-accent standard) (1) M/N standard. (2) B standard. (3) D/K and L standard. (4) G/H, I and L-accent standard. Fig 10. Notch filter for adjacent sound carrier suppression TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 29 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 22. FILTERS_2 register (address 10h) bit description Legend: * = default value. Bit Symbol Access Value Description 7 and 6 - R/W 5 R/W VID_FILT_ LOW_RIP 4 - R/W 3 to 0 SBP[3:0] R/W 00* not used video filter characteristic adjust 0 smooth roll-off 1* low ripple 1* reserved, must be set to logic 1 The SSIF band-pass attenuates unwanted video frequencies[1][2], e.g. color carrier. For FM radio standard it provides almost channel selectivity (see Figure 12). 0001* SSIF band-pass, wide bandwidth 0010 SSIF band-pass, normal bandwidth (1.1 MHz, all TV standards) 0100 SSIF band-pass, narrow bandwidth (200 kHz, FM radio) [1] SSIF band-pass center frequency is controlled by DTO_SC[23:0]. See Table 20 for recommended DTO values. [2] Deviating from easy programming values for FILTERS_2, the narrow SSIF band-pass filter (SPB[3:0] = 0100) should be used for M/N standard. 001aan681 2 amplitude response (dB) -2 (1) (2) (3) (4) -6 -10 0 2 4 6 frequency (MHz) (1) 4 MHz video filter in smooth roll off mode (2) 4 MHz video filter in low ripple mode (3) 5 MHz video filter in smooth roll off mode (4) 5 MHz video filter in low ripple mode Fig 11. Video low pass frequency response in smooth roll off or low ripple mode TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 30 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 008aaa228 10 resp(f) (dB) (1) (2) (3) -10 -30 -50 -70 0 2 4 6 8 10 12 14 f (MHz) (1) Wide bandwidth (e.g. for search mode). (2) All TV standards, normal bandwidth (1.1 MHz). (3) FM radio, narrow bandwidth (200 kHz). Fig 12. SSIF and FM radio band-pass filters (center frequency 5.5 MHz chosen) 9.3.7 Group delay equalization Table 23. GRP_DELAY register (address 11h) bit description Legend: * = default value. Bit Symbol 7 GD_EQ_CTRL R/W 6 and 5 4 to 0 TDA8296 Product data sheet Access Value R/W Description group delay equalizer control; this is the control for the freely programmable group delay equalizer; for details see Section 9.3.19 0* off (equalizer bypassed) 1 on (equalizer active) 00* GRP_DEL[4:0] R/W reserved, must be set to logic 00 group delay equalization to correct the transmitter predistortion 0 0001* group delay M/N standard 0 0010 group delay B/G/H standard 0 0100 group delay D/K standard 0 1000 group delay L/L-accent standard 1 0000 group delay I (flat) standard All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 31 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 9.3.8 Digital IF AGC functions Table 24. D_IF_AGC_SET_1 register (address 12h) bit description Legend: * = default value. Bit Symbol Access Value Description 7 - R/W reserved, must be set to logic 1 6 D_IF_AGC_MODE R/W 5 to 0 - 1* If HIGH, the digital IF AGC detection and gating is done during the back porch of the video signal. This Detection mode can be used for all standards (also L/L-accent standard) without impact on the IF AGC loop speed. R/W 0* peak sync AGC (slow peak white L/L-accent standard) 1 black level AGC detection 10 0000* reserved, must be set to logic 10 0000 Table 25. D_IF_AGC_SET_2 register (address 13h) bit description Legend: * = default value. Bit Symbol Access Value Description 7 - R/W reserved, must be set to logic 1 1* 6 to 0 D_IF_AGC_BW[6:0] R/W digital IF AGC 3 dB-loop bandwidth setting 000 0001 25 Hz 000 0010 50 Hz 000 0100 100 Hz 000 1000 200 Hz 001 0000* 400 Hz 010 0000 800 Hz 100 0000 1.6 kHz (not recommended) 9.3.9 Tuner IF AGC functions Table 26. T_IF_AGC_SET register (address 15h) bit description Legend: * = default value. TDA8296 Product data sheet Bit Symbol Access Value Description 7 POL_TIF R/W tuner IF AGC polarity 0 inverted tuner IF AGC polarity 1* normal tuner IF AGC polarity: the higher the necessary gain, the higher the IF AGC voltage All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 32 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 26. T_IF_AGC_SET register (address 15h) bit description ...continued Legend: * = default value. Bit Symbol Access Value Description 6 to 0 T_IF_AGC_SPEED[6:0] R/W T_IF_AGC_SPEED determines the tuner IF AGC loop speed 000 0001 -18 dB nominal 000 0010 -12 dB nominal 000 0100 -6 dB nominal 000 1000* nominal speed (determined by the tuner IF control slope) 001 0000 +6 dB nominal 010 0000 +12 dB nominal 100 0000 +18 dB nominal Table 27. T_IF_AGC_LIM register (address 16h) bit description Legend: * = default value. Bit Symbol 7 to 4 UP_LIM[3:0] Access Value Description R/W The tuner IF AGC output voltage can be limited to interface with concepts having power supply < 3.3 V. UP_LIM determines the upper limit from 12 FS (= 0h) to FS (= Fh). The format is straight binary. 1111* 3 to 0 LOW_LIM[3:0] set upper limit to maximum R/W LOW_LIM determines the lower tuner IF AGC output limit from 0 (= 0h) to 12 FS (= Fh). The format is straight binary. 0000* set lower limit to minimum Table 28. T_IF_AGC_FORCE register (address 17h) bit description Legend: * = default value. Bit Symbol Access Value Description 7 T_FORCE R/W the tuner IF AGC output voltage can be forced externally to a fixed voltage, determined by T_FORCE_VAL 6 to 0 T_FORCE_VAL[6:0] TDA8296 Product data sheet 0* tuner IF AGC normal operation 1 tuner IF AGC output voltage determined by T_FORCE_VAL R/W T_FORCE_VAL determines the tuner IF AGC forced value. So the tuner IF AGC can be fixed to a certain value for debugging purposes. Format is straight binary. 3Fh* 0.5 x VDD(3V3), i.e. 1.65 V nominally XXh don't care if T_FORCE = 0 All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 33 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 9.3.10 V-sync adjustment Table 29. V_SYNC_DEL register (address 1Ch) bit description Legend: * = default value. Bit Symbol Access Value 7 and 6 VS_WIDTH[1:0] R/W 5 4 to 0 VS_POL VS_DEL[4:0] Description VS_WIDTH determines the width (in horizontal lines) of the V-sync gating pulse (needed for gating of tuner RF AGC2) 00 width 1 line (64 s) 01* width 2 lines 10 width 4 lines 11 width 16 lines R/W VS_POL determines the polarity of the V-sync pulse: if VS_POL = 1, the first edge of the pulse is positive, else negative. 0 first edge negative 1* first edge positive R/W VS_DEL determines the first edge position of the output V-sync pulse compared to the beginning of the vertical blanking interval: pulse_position = ( VS_DEL - 12 ) lines 0Fh* first edge 3 lines after beginning of vertical interval 9.3.11 CVBS settings Table 30. CVBS_SET register (address 1Dh) bit description Legend: * = default value. Bit Symbol Access Value Description 7 and 6 - R/W 00* not used 5 and 4 - R/W 11* must be set to logic 11 or in case of L/L-accent to 01 3 2 1 CVBS_EQ_ R/W CTRL FOR_BLK AUTO_BLK video equalizer mode control 0* mode using predefined settings like described in Table 32 1 free programmable mode; for details see Section 9.3.19 R/W when active, the video output is always blanked, e.g. for channel change (forced blank) 0* no action 1 video blanked R/W when active, the video output is blanked if the horizontal line lock flag (N_H_LOCK, see Table 41) is not present 0* 1 0 TDA8296 Product data sheet - R/W 1* auto-blanking off auto-blanking on reserved, must be set to logic 1 All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 34 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 31. CVBS_LEVEL register (address 1Eh) bit description Legend: * = default value. Bit Symbol Access Value 7 to 0 CVBS_LVL[7:0] R/W Description With this byte, the nominal video output level is freely programmable. The format is unsigned integer (offset binary). Settings below 40h and above C0h, which correspond to -5 dB (40h) and +4.5 dB (C0h) related to the default value, are forbidden. In the following some possible settings in 1 dB steps are shown. 51h -3 dB nominal 5Bh -2 dB nominal 66h -1 dB nominal 73h* nominal: 1 V (p-p) video output level (sync-peak) 81h +1 dB nominal 91h +2 dB nominal A2h +3 dB nominal Table 32. CVBS_EQ register (address 1Fh) bit description Legend: * = default value. Bit Symbol Access Value 7 to 0 CVBS_EQ[7:0] R/W TDA8296 Product data sheet Description The video equalizer can be used for the compensation of a principal tuner tilt or to change the video frequency according to customer taste. The figures given are at 5 MHz CVBS with respect to low frequencies (see Figure 13). 0000 0001 The video frequency response is -8 dB for 5 MHz. 0000 0010 The video frequency response is -6 dB for 5 MHz. 0000 0100 The video frequency response is -4 dB for 5 MHz. 0000 1000 The video frequency response is -2 dB for 5 MHz. 0001 0000* The video frequency response is made flat in this mode. 0010 0000 The video frequency response is +2 dB (peaking) for 5 MHz. 0100 0000 The video frequency response is +4 dB (peaking) for 5 MHz. 1000 0000 The video frequency response is +6 dB (peaking) for 5 MHz. All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 35 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 001aah361 10 resp(f) (dB) 6 2 -2 -6 -10 0 1 2 3 4 5 6 7 f (MHz) Fig 13. Video equalizer curves 9.3.12 SSIF and mono sound settings Table 33. SSIF_MUTE register (address 05h) bit description Legend: * = default value. Bit Symbol 7 and 6 5 to 2 1 Access Value Description R/W not used 00* SSIF_AFC_WIN[3:0] R/W SSIF_MUTE_TYPE SSIF AFC mute window configuration 0001* 100 kHz 0010 200 kHz 0100 400 kHz 1000 800 kHz R/W SSIF auto-mute behavior 0* reduced gain 1 0 SSIF_MUTE_CTRL R/W mute auto-mute of SSIF output 0* off 1 on Table 34. SOUNDSET_1 register (address 20h) bit description Legend: * = default value. Bit Symbol Access Value Description 7 - R/W reserved, must be set to logic 0 6 and 5 AM_FM_SND[1:0] TDA8296 Product data sheet 0* R/W Output mode for inbuilt FM/AM mono sound demodulator 01* FM sound 10 AM sound (only L/L-accent standard) XX don't care if SSIF output is chosen (SSIF_SND[1:0] = 10) All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 36 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 34. SOUNDSET_1 register (address 20h) bit description ...continued Legend: * = default value. Bit Symbol Access Value Description 4 to 0 DEEMPH[4:0] R/W mono sound de-emphasis adjustment to compensate transmitter pre-emphasis; or low-pass filter to remove out of audio band interferers 0 0001* de-emphasis of 75 s for M/N standard or non-European FM radio to compensate the transmitter pre-emphasis 0 0010 de-emphasis of 50 s for B/G/H, D/K and I standard or European FM radio to compensate the transmitter pre-emphasis 0 0100 low-pass filter with 30 kHz -3 dB cut-off frequency to remove out of audio band interferers 0 1000 low-pass filter with 140 kHz -3 dB cut-off frequency to drive an external BTSC stereo decoder 1 0000 The de-emphasis filter is bypassed. This can be used for debugging or other purposes. Table 35. SOUNDSET_2 register (address 21h) bit description Legend: * = default value. Bit Symbol Access Value Description 7 - R/W reserved, must be set to logic 0 6 SSIF_AGC_TC R/W 5 0* SSIF AGC time constant for L/L-accent standard 0* slow (normal) 1 fast SSIF_AGC_CTRL R/W SSIF AGC control 0 1* 4 3 HD_DK FOR_MUTE TDA8296 Product data sheet R/W SSIF AGC off SSIF AGC on When active, the internal FM mono sound demodulator can handle excessive FM deviations up to 400 kHz. This might happen in D/K standard China. To activate this mode, it is mandatory to set D/K standard first. The sound output level has to be adapted accordingly by the microprocessor to avoid sound DAC clipping. E.g. for 400 kHz FM deviation, the -12 dB setting of the sound level register (see Table 36) is recommended. 0* high Deviation mode off 1 high Deviation mode on X don't care if SSIF output is chosen (SSIF_SND[1:0] = 10) R/W When active, the mono sound signal is always muted. This setting only makes sense in case the sound DAC output is also set to mono sound (SSIF_SND[1:0] = 01). FOR_MUTE has no function if SSIF_SND[1:0] = 10. 0* off 1 on X don't care if SSIF output is chosen (SSIF_SND[1:0] = 10) All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 37 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 35. SOUNDSET_2 register (address 21h) bit description ...continued Legend: * = default value. Bit Symbol Access Value Description 2 AUTO_MUTE R/W When active, the mono sound signal is muted if the horizontal lock flag (N_H_LOCK) disappears. This setting only makes sense in case the sound DAC output is also set to mono sound (SSIF_SND[1:0] = 01). FOR_MUTE has no function if SSIF_SND[1:0] =10. 0* off 1 on X 1 and 0 SSIF_SND[1:0] [1] don't care if SSIF output is chosen (SSIF_SND[1:0] = 10) R/W either mono sound or SSIF can be chosen for the sound DAC output 01 mono sound[1] 10* SSIF Before activating mono sound, the TV standard needs to be set via easy programming Table 36. SOUND_LEVEL register (address 22h) bit description Legend: * = default value. Bit Symbol 7 to 5 - Access Value Description R/W not used 000* 4 to 0 SND_LVL[4:0] R/W TDA8296 Product data sheet mono sound output level 0 0001 -12 dB nominal; implemented for flexibility reasons. With this setting, the adaptation to different standard requirements can be done. 0 0010 -6 dB nominal; implemented for flexibility reasons. With this setting, the adaptation to different standard requirements can be done. It is chosen for FM radio because of the large FM deviation involved. 0 0100 Nominal setting; FM deviations up to 100 kHz can be processed without sound DAC clipping. The clipping level is 535 mV (RMS) typically. 0 1000* +6 dB nominal; chosen for M/N standard due to less nominal frequency deviation 1 0000 +12 dB nominal; implemented for flexibility reasons. With this setting, the adaptation to different standard requirements can be done. X XXXX don't care if SSIF output is chosen (SSIF_SND[1:0] = 10) All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 38 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 37. SSIF_LEVEL register (address 23h) bit description Legend: * = default value. Bit Symbol 7 to 0 SSIF_LVL[7:0] Access Value Description R/W SSIF output level adjustment; SSIF AGC on (21h[5] = 1) 1111 1111 +3 dB : : 1010 1111* 0 dB : : 0100 0000 to 0000 0000 -8.7 dB SSIF output level adjustment; SSIF AGC off (21h[5] = 0) XXX0 0001 -12 dB nominal; implemented for flexibility reasons. With this setting, the adaptation to different standard requirements can be done. XXX0 0010 -6 dB nominal; implemented for flexibility reasons. With this setting, the adaptation to different standard requirements can be done. XXX0 0100 Nominal setting; typical output level is 55 mV (RMS) for PC / SC ratio of 13 dB (see Section 12, SSIF/mono sound output). XXX0 1000 +6 dB nominal; implemented for flexibility reasons. With this setting, the adaptation to different standard requirements can be done. XXX1 0000 +12 dB nominal; implemented for flexibility reasons. With this setting, the adaptation to different standard requirements can be done. XXXX XXXX don't care if mono sound output is chosen (SSIF_SND[1:0] = 01) Remark: The SSIF level depends also on the used capacitor CS. Please refer to Figure 14 TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 39 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 001aam355 140 SSIFout (mVrms) 120 (1) (2) (3) (4) (5) 100 80 4.5 5.0 5.5 6.0 6.5 frequency (MHz) (1) 150 pF (2) 180 pF (3) 220 pF (used for characteristics data) (4) 270 pF (5) 330 pF Fig 14. TDA8296 SSIF characteristic versus CS (refer to Figure 23) typical values; termination 75 and 1 k in parallel 9.3.13 Status registers: ADC saturation, AFC, H/V PLL and AGC Table 38. Bit ADC_SAT register (address 24h) bit description Symbol Access Value 7 to 0 ADC_SAT[7:0] R - Description With ADC_SAT, the ADC saturation percentage in a period of 40 ms can be calculated by the following ADC_SAT formula: saturation = ------------------------- (%) . 256 TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 40 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 39. Bit AFC register (address 25h) bit description Symbol 7 to 0 AFC[7:0] Access Value Description R This is the readout for AFC. AFC contains the frequency deviation from nominal IF picture carrier. The format is twos complement, 13.2 kHz steps are done per LSB. See Table 40 for details. The frequency deviation could also be given by the following formula: - - AFC x 6 750 f IF - f nom = ---------------------------------- (kHz) . For a frequency 512 deviation from the nominal IF picture carrier greater than the FPLL pull-in capability (-830.6 kHz to +843.8 kHz or -1 674.3 kHz to +1 687.5 kHz), the output reading is undefined. The AFC lock indication can be taken from the N_H_LOCK information from the H-sync PLL. The lock occurs inside a frequency window, which is determined by the pull-in capability of the FPLL. Table 40. Calculation of frequency deviation from AFC value Deviation from nominal AFC[7] AFC[6] AFC[5] AFC[4] AFC[3] AFC[2] AFC[1] AFC[0] IF frequency[1] fIF = fnom - 1 674.3 kHz 0 1 1 1 1 1 1 1 fIF = fnom - 1 661.1 kHz 0 1 1 1 1 1 1 0 : : : : : : : : : fIF = fnom - 830.6 kHz 0 0 1 1 1 1 1 1 fIF = fnom - 817.4 kHz 0 0 1 1 1 1 1 0 : : : : : : : : : fIF = fnom - 13.2 kHz 0 0 0 0 0 0 0 1 fIF = fnom 0 0 0 0 0 0 0 0 fIF = fnom + 13.2 kHz 1 1 1 1 1 1 1 1 : : : : : : : : : fIF = fnom + 830.6 kHz 1 1 0 0 0 0 0 1 fIF = fnom + 843.8 kHz 1 1 0 0 0 0 0 0 : : : : : : : : : fIF = fnom + 1 674.3 kHz 1 0 0 0 0 0 0 1 fIF = fnom + 1 687.5 kHz 1 0 0 0 0 0 0 0 [1] TDA8296 Product data sheet See Section 12 for nominal IF frequencies. All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 41 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 001aam356 150 AFC reg val 50 -50 (1) (2) (2) 830 kHz PLL lock mode (1) 1660 kHz PLL lock mode -150 -2000 -1000 0 1000 2000 Df (MHz) (1) Undefined area in 1660 kHz mode (2) Undefined area in 830 kHz mode Fig 15. TDA8296 AFC characteristic Table 41. Bit HVPLL_STAT register (address 26h) bit description Symbol Access Value Description R - not used 5 NOISE_DET R - This flag gets HIGH in case the video S/N (weighted) drops below 30 dB. For proper and noise free video signals it stays LOW. It can be used for debugging and other purposes. 4 MAC_DET R - This flag indicates the presence of copy-guarded video content from STBs or VCRs. It can be used for debugging and other purposes. 3 FIDT R - This flag indicates the frame rate (50 Hz or 60 Hz). When active, 60 Hz is detected. It can be used for debugging and other purposes. 2 V_LOCK R - This flag is active, if a proper frame (50 Hz or 60 Hz) is detected. It can be used for debugging and other purposes. 1 F_H_LOCK R - This flag is active, if a proper H-sync (15.625 kHz or 15.734 kHz) is detected (Fast mode). It can be used for debugging and other purposes. 0 N_H_LOCK R - This flag is active, if a proper H-sync (15.625 kHz or 15.734 kHz) is detected (Normal mode). It can be used for debugging and other purposes. 7 and 6 - TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 42 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 42. Bit D_IF_AGC_STAT register (address 27h) bit description Symbol Access Value 7 to 0 D_IF_AGC_STAT[7:0] R - Description D_IF_AGC_STAT is the digital IF AGC status readout byte. Contains the digital IF AGC loop DC information. The format is twos complement. To get the internal gain in dB, the following formula can be used: D_IF_AGC_STAT + 50 gain = -------------------------------------------------------- (dB) . 3.675 Table 43. Bit T_IF_AGC_STAT register (address 28h) bit description Symbol Access Value 7 to 0 T_IF_AGC_STAT[7:0] R Table 44. Bit - Description T_IF_AGC_STAT is the IF AGC status readout byte. Contains the tuner IF AGC loop DC information. The format is offset binary. ALT_FILT_COEF register (address 2Bh) bit description Symbol Access Value Description 7 to 2 not used R/W 0 not used. 1 to 0 ALT_FILT_COEF R/W 00 internal selection of fixed coefficients for video low pass filter using an ADC sampling frequency of 01 10 Table 45. Bit Frequency 54.00 MHz 50.75 MHz 57.25 MHz SSIF_AGC_STAT register (address 2Dh) bit description Symbol Access Value 7 to 0 SSIF_AGC_STAT[7:0] R - Description SSIF_AGC_STAT contains the SSIF AGC gain information. To get the internal gain in dB, the following formula can be used: gain = 20 log SSIF_AGC_STAT ------------------------------------------- . The value is 8 10 approximately the PC / SC ratio. 9.3.14 Chip identification and Standby mode Table 46. Bit IDENTITY register (address 2Fh) bit description Symbol Access Value 7 to 0 IDENTITY[7:0] R Description 1000 1100* chip identification, value corresponds to TDA8296 Table 47. CLB_STDBY register (address 30h) bit description Legend: * = default value. Bit TDA8296 Product data sheet Symbol Access Value Description 7 to 3 - R/W 0000 0* not used 2 R/W 0* - reserved, must be set to logic 0 All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 43 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 47. CLB_STDBY register (address 30h) bit description ...continued Legend: * = default value. Bit Symbol Access Value Description 1 STDBY When STDBY is set to logic 1, the chip enters in Standby mode, and its power consumption is reduced. The IF AGC pin is set to high-ohmic. The default value is logic 0, which means that the chip is active. 0 CLB R/W 0* Normal mode 1 Standby mode This signal clears the TDA8296 through the I2C-bus interface (software reset). To activate the reset, just write CLB = 0. This software reset will not affect the content of the registers. R/W 0 activate soft reset 1* normal operation 9.3.15 ADC control In the TDA8296 a 12-bit ADC is implemented sampling with a 54 MHz clock (27 MHz optional). Table 48. ADC_CTL register (address 33h) bit description Legend: * = default value. Bit Symbol Access Value Description 7 to 4 - R/W reserved, must be set to logic 0010 3 R/W DCIN 0010* The input signal of the ADC can be either AC coupled by means of two capacitors or connected directly to the inputs (DC coupled). 0* AC coupling 1 2 - R/W 1 SLEEP R/W 1* DC coupling reserved, must be set to logic 1 When HIGH, SLEEP sets the ADC into its Sleep mode. Both bias current and clock are switched off. In this mode, the current consumption is reduced by a factor of 6. The reference circuit will remain active in order to guarantee a fast recovery from Sleep mode. 0* Normal mode 1 0 PD_ADC R/W ADC Sleep mode When HIGH, PD_ADC sets the ADC into its Power-down mode. All internal currents are switched off. In this mode, the current consumption is near zero (leakage current only). 0* Normal mode 1 ADC Power-down mode Table 49. ADC_CTL_2 register (address 34h) bit description Legend: * = default value. TDA8296 Product data sheet Bit Symbol Access Value 7 to 3 - R/W 0000 0* not used Description 2 and 1 - R/W 10* reserved, must be set to logic 10 All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 44 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 49. ADC_CTL_2 register (address 34h) bit description ...continued Legend: * = default value. Bit Symbol Access Value Description 0 AD_SR54M R/W AD_SR54M sets the ADC sampling rate 0 ADC sampling rate 27 MHz; first decimation filter is bypassed 1* ADC sampling rate 54 MHz 001aan682 5 amplitude response (dB) 0 (1) (2) -5 -10 -15 -20 0 2 4 6 8 10 12 14 frequency (MHz) (1) ADC sample rate 27 MHz (2) ADC sample rate 54 MHz ADC sample rate of 54 MHz recommended for optimum aliasing suppression. Internal low IF tilt in 54 MHz mode can be compensated by CVBS_EQ[7:0] set to -2 dB Fig 16. Internal low IF frequency response in front of the VIF demodulator 9.3.16 Video and sound DAC control The TDA8296 implements two 10-bit DAC modules (CVBS and sound outputs) which are sampled by a 108 MHz clock. A reference module derives biasing currents for the two DACs. Table 50. VIDEODAC_CTL register (address 35h) bit description Legend: * = default value. Bit Symbol Access Value Description 7 - R/W reserved, must be set to logic 0 0* 6 to 1 B_DA_V[5:0] R/W 0 TDA8296 Product data sheet PD_DA_V B_DA_V modifies between 50% to 100% the full scale DAC output current. See Section 13.3. 00 0000 minimum current setting 11 1111* maximum current setting R/W When HIGH, PD_DA_V sets the video DAC into its Power-down mode. 0* Normal mode 1 video DAC Power-down mode All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 45 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 51. AUDIODAC_CTL register (address 36h) bit description Legend: * = default value. Bit Symbol Access Value Description 7 - R/W reserved, must be set to logic 0 0* 6 to 1 B_DA_S[5:0] R/W B_DA_S modifies between 50% to 100% the full scale DAC output current. See Section 13.3. 00 0000* 11 1111 0 PD_DA_S R/W minimum current setting maximum current setting When HIGH, PD_DA_S sets the sound DAC into its Power-down mode. 0* Normal mode 1 sound DAC Power-down mode Table 52. DAC_REF_CLK_CTL register (address 37h) bit description Legend: * = default value. Bit Symbol Access Value Description 7 not used - R/W 0* 6 to 1 - R/W 10 0000* reserved, must be set to logic 10 0000 0 R/W PD_DA_REF When HIGH, PD_DA_REF sets the reference module into its Power-down mode. 0* Normal mode 1 Power-down mode 9.3.17 Clock generation (PLL and crystal oscillator) The TDA8296 implements a crystal oscillator which can be used either in Slave mode or in Oscillator mode (see Section 13.7), and a multipurpose PLL which receives XIN as input clock, and delivers the system clock of the IC (108 MHz). Table 53. PLL_REG07, PLL_REG08, PLL_REG09 and PLL_REG10 register (address 3Fh to 42h) bit description Legend: * = default value. Address Register Symbol Access Value Description - R/W 0* not used NSEL7 R/W 0* It programs bit 7 of the N parameter (N = NSEL + 1). N is the PLL pre-divider. See below for bits NSEL[6:0]. R/W 00h* reserved, must be set to 00h 40h PLL_REG08 7 to 0 MSEL[7:0] R/W 1Ah* It programs the M parameter (M = MSEL + 1). M is the PLL feedback-divider. 41h PLL_REG09 7 to 1 NSEL[6:0] R/W 01h* It programs bits 6 to 0 of the N parameter (N = NSEL + 1). N is the PLL pre-divider. - R/W 0* reserved, must be set to logic 0 42h PLL_REG10 7 to 5 - R/W 000* reserved, must be set to logic 000 4 to 0 PSEL[4:0] R/W 01h* It programs the P parameter (P = PSEL + 1). P is the PLL post-divider. 3Fh Bit PLL_REG07 7 6 5 to 0 - 0 The PLL output frequency (108 MHz) can be calculated with the following formula: fi x M f VCO = ------------f clk(o)(PLL) = -----------NxP 2xP TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (1) (c) NXP B.V. 2011. All rights reserved. 46 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio For optimum performances, the following relations must be respected: * 275 MHz fVCO 550 MHz * 4 kHz fi / N 150 MHz 9.3.18 GPIOs In the TDA8296, three general purpose input/outputs are implemented. Table 54. GPIOREG_0 register (address 44h) bit description Legend: * = default value. Bit Symbol 7 to 4 GP1_CF[3:0] 3 to 0 GP0_CF[3:0] Access Value Description R/W It determines how the general purpose pin GPIO1 is configured. 0000 The GPIO1 pin is in Input mode. The input value is stored in GP1_VAL. 0001* The GPIO1 pin is in Open-drain mode. The output value is determined by GP1_VAL. 0011 The GPIO1 pin is in Output mode. The PLL output clock divided by two is delivered. 0100 to 1011 The GPIO1 pin is in Output mode. HVPLL signals are delivered. The HVPLL signal is chosen according to Table 56. XXXX Don't care if I2CSW_EN = 1. Then the pad is configured as I2C-bus feed-through like described in Table 55. R/W It determines how the general purpose pin GPIO0 is configured. 0000 The GPIO0 pin is in Input mode. The input value is stored in GP0_VAL. 0001 The GPIO0 pin is in Open-drain mode. The output value is determined by GP0_VAL. 0011 The GPIO0 pin is in Output mode. The PLL output clock divided by two is delivered. 0100 to 1011* The GPIO0 pin is in Output mode. HVPLL signals are delivered. The HVPLL signal is chosen according to Table 56. Table 55. GPIOREG_1 register (address 45h) bit description Legend: * = default value. Bit Symbol Access Value Description 7 I2CSW_EN R/W 1* 6 I2CSW_ON R/W 0* When I2CSW_EN = 1, GPIO1 and GPIO2 are configured as an I2C-bus feed-through independently of the GP1_CF and GP2_CF value. When I2CSW_ON = 0, the feed-through switch is open, and GPIO1 and GPIO2 are in 3-state. When the switch is closed (I2CSW_ON = 1), the I2C-bus clock and data signals (SCL and SDA) are available on the GPIO1 and GPIO2 pins. R/W 00* 5 and 4 - TDA8296 Product data sheet not used All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 47 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 55. GPIOREG_1 register (address 45h) bit description ...continued Legend: * = default value. Bit Symbol 3 to 0 GP2_CF[3:0] R/W Table 56. Access Value Description It determines how the general purpose pin GPIO2 is configured. 0000 The GPIO2 pin is in Input mode. The input value is stored in GP2_VAL. 0001* The GPIO2 pin is in Open-drain mode. The output value is determined by GP2_VAL. 0011 The GPIO2 pin is in Output mode. The PLL output clock divided by two is delivered. 0100 to 1011 The GPIO2 pin is in Output mode. HVPLL signals are delivered. The HVPLL signal is chosen according to Table 56. XXXX Don't care if I2CSW_EN = 1. Then the pad is configured as I2C-bus feed-through. HVPLL signal configuration HVPLL_BUS bit Signal GPx_CF[3:0] = 1011 V_SYNC GPx_CF[3:0] = 1010 H_SYNC GPx_CF[3:0] = 1001 NOISE_DET GPx_CF[3:0] = 1000 MAC_DET GPx_CF[3:0] = 0111 FIDT GPx_CF[3:0] = 0110 V_LOCK GPx_CF[3:0] = 0101 F_H_LOCK GPx_CF[3:0] = 0100 N_H_LOCK Table 57. GPIOREG_2 register (address 46h) bit description Legend: * = default value. TDA8296 Product data sheet Bit Symbol Access Value Description 7 to 5 - R/W 000* reserved, must be set to logic 000 4 and 3 - R/W 00* not used 2 GP2_VAL R/W 1* GP2_VAL controls the value of the pin GPIO2 when GP2_CF[3:0] = 0001. When GP2_CF[3:0] = 0000, GPIO2 is an input pin which value can be read through the I2C-bus stored in GP2_VAL. 1 GP1_VAL R/W 1* GP1_VAL controls the value of the pin GPIO1 when GP1_CF[3:0] = 0001. When GP1_CF[3:0] = 0000, GPIO1 is an input pin which value can be read through the I2C-bus stored in GP1_VAL. 0 GP0_VAL R/W 1* GP0_VAL controls the value of the pin GPIO0 when GP0_CF[3:0] = 0001. When GP0_CF[3:0] = 0000, GPIO0 is an input pin which value can be read through the I2C-bus stored in GP0_VAL. All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 48 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 9.3.19 Special equalizer functions for group delay and video (CVBS) To realize special customer demands or accurate compensation of the tuner influence, the TDA8296 has got freely programmable equalizers for the group delay and video (CVBS) response. In Table 58 the programming of the group delay equalizer is explained, in Table 60 the programming of the video equalizer. For each equalizer type an example is given. Table 58. GD_EQ_SECTx_C1 and GD_EQ_SECTx_C2 (x = 1 to 4) register (address 4Bh to 52h) bit description Legend: * = default value[1]. Address Register Bit Symbol Access Value 4Bh GD_EQ_SECT1_C1 7 to 0 GD_EQ_SECT1_C1[7:0] R/W 00h* 4Ch GD_EQ_SECT1_C2 7 to 0 GD_EQ_SECT1_C2[7:0] R/W 00h* 4Dh GD_EQ_SECT2_C1 7 to 0 GD_EQ_SECT2_C1[7:0] R/W 00h* 4Eh GD_EQ_SECT2_C2 7 to 0 GD_EQ_SECT2_C2[7:0] R/W 00h* 4Fh GD_EQ_SECT3_C1 7 to 0 GD_EQ_SECT3_C1[7:0] R/W 00h* 50h GD_EQ_SECT3_C2 7 to 0 GD_EQ_SECT3_C2[7:0] R/W 00h* 51h GD_EQ_SECT4_C1 7 to 0 GD_EQ_SECT4_C1[7:0] R/W 00h* 52h GD_EQ_SECT4_C2 7 to 0 GD_EQ_SECT4_C2[7:0] R/W 00h* [1] Don't care if GD_EQ_CTRL = 0; see Table 23. Remark: The group delay equalizer consists of four cascaded all-pass Infinite Impulse Response (IIR) sections of second order (8th order in sum). The transfer function H(z) of one section is as follows, while the sampling rate is 13.5 MHz: -1 -2 b2 + b1 x z + z H ( z ) = -----------------------------------------------------1 -2 1 + b1 x z + b2 x z GD_EQ_SECTx_C1 and GD_EQ_SECTx_C2 (x = 1 to 4) are defining the linear and square coefficient of each section, i.e. GD_EQ_SECTx_C1 = b1 and GD_EQ_SECTx_C2 = b2. The coefficients are in signed fixed-point format, the representation is in two's complement. There is one sign bit, one magnitude bit and 6 fractional bits. Each fractional bit represents an inverse power of two, so that the highest value for a coefficient is 20 + 2-1 + ... + 2-6 = 21 - 2-6 = 1.984375. The binary representation for this value is 01.11 1111 (= 7Fh) and all bits except the sign bit are logic 1. As two's complement is chosen, the lowest value for a coefficient is -2, which is 10.00 0000 (= 80h) in the binary representation. So, for the lowest possible value, only the sign bit is logic 1. The shown default values for GD_EQ_SECTx_C1 and GD_EQ_SECTx_C2 (x = 1 to 4) implement a flat equalizer response. Example of Table 58: If e.g. a flat group delay response up to 4 MHz and -70 ns from 4.43 MHz to 5 MHz on the CVBS signal is wanted, one might realize a characteristic like shown in Figure 17. TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 49 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 001aaj779 0.65 td(grp) (s) 0.62 0.59 0.56 0.53 0 1 2 3 4 5 f (MHz) Fig 17. Example for the programmable group delay equalizer The coefficients used in the above filter are according to Table 59. To get any other filter characteristic use a professional filter tool to determine the coefficients. Table 59. Coefficients used in group delay equalizer example Symbol Value GD_EQ_SECT1_C1[7:0] B9h GD_EQ_SECT1_C2[7:0] 16h GD_EQ_SECT2_C1[7:0] DBh GD_EQ_SECT2_C2[7:0] 17h GD_EQ_SECT3_C1[7:0] 0Eh GD_EQ_SECT3_C2[7:0] 19h GD_EQ_SECT4_C1[7:0] 47h GD_EQ_SECT4_C2[7:0] 1Ch Table 60. CVBS_EQ_COEFx_LOW and CVBS_EQ_COEFx_HIGH (x = 0 to 5) register (address 57h to 62h) bit description Legend: * = default value[1]. Address Register Bit Symbol Access Value 57h CVBS_EQ_COEF0_LOW 7 to 0 CVBS_EQ_COEF0[7:0] R/W 00h* 58h CVBS_EQ_COEF0_HIGH 7 to 4 - R/W 0000* 3 to 0 CVBS_EQ_COEF0[11:8] R/W 0h* 59h CVBS_EQ_COEF1_LOW 7 to 0 CVBS_EQ_COEF1[7:0] R/W 00h* 5Ah CVBS_EQ_COEF1_HIGH 7 to 4 - R/W 0000* 3 to 0 CVBS_EQ_COEF1[11:8] R/W 0h* 5Bh CVBS_EQ_COEF2_LOW 7 to 0 CVBS_EQ_COEF2[7:0] R/W 00h* 5Ch CVBS_EQ_COEF2_HIGH 7 to 4 - R/W 0000* 3 to 0 CVBS_EQ_COEF2[11:8] R/W 0h* 7 to 0 CVBS_EQ_COEF3[7:0] R/W 00h* 5Dh TDA8296 Product data sheet CVBS_EQ_COEF3_LOW All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 50 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 60. CVBS_EQ_COEFx_LOW and CVBS_EQ_COEFx_HIGH (x = 0 to 5) register (address 57h to 62h) bit description ...continued Legend: * = default value[1]. Address Register Bit Symbol Access Value 5Eh CVBS_EQ_COEF3_HIGH 7 to 4 - R/W 0000* 3 to 0 CVBS_EQ_COEF3[11:8] R/W 0h* 5Fh CVBS_EQ_COEF4_LOW 7 to 0 CVBS_EQ_COEF4[7:0] R/W 00h* 60h CVBS_EQ_COEF4_HIGH 7 to 4 - R/W 0000* 3 to 0 CVBS_EQ_COEF4[11:8] R/W 0h* 61h CVBS_EQ_COEF5_LOW 7 to 0 CVBS_EQ_COEF5[7:0] R/W 00h* 62h CVBS_EQ_COEF5_HIGH 7 to 4 - R/W 0000* 3 to 0 CVBS_EQ_COEF5[11:8] R/W 4h* [1] Don't care if CVBS_EQ_CTRL = 0; see Table 32. Remark: The overall video (CVBS) equalizer is a symmetric FIR filter with 11 taps. Due to the symmetry the group delay is constant (linear phase). The transfer function is as follows, while the sampling rate is 13.5 MHz: H ( z ) = h0 + h1 x z -1 + h2 x z -2 + h3 x z -3 + h4 x z -4 + ... + h 10 x z - 10 Please note that because of the symmetry h0 = h10, h1 = h9, h2 = h8, h3 = h7 and h4 = h6. The mid coefficient h5 is only present once. CVBS_EQ_COEFx (x = 0 to 5) are defining the coefficients, i.e. CVBS_EQ_COEF0 = h0 = h10, CVBS_EQ_COEF1 = h1 = h9, CVBS_EQ_COEF2 = h2 = h8, CVBS_EQ_COEF3 = h3 = h7, CVBS_EQ_COEF4 = h4 = h6 and CVBS_EQ_COEF5 = h5. Each of the coefficients h0 to h5 has got 12-bit quantization. The coefficients are in signed fixed-point format, the representation is in two's complement. There is one sign bit, one magnitude bit and 10 fractional bits. Each fractional bit represents an inverse power of two, so that the highest value for a coefficient is 20 + 2-1 + ... + 2-10 = 21 - 2-10 = 1.9990234375. The binary representation for this value is 01.11 1111 1111 (= 7FFh) and all bits except the sign bit are logic 1. As two's complement is chosen, the lowest value for a coefficient is -2, which is 10.00 0000 0000 (= 800h) in the binary representation. So, for the lowest possible value, only the sign bit is logic 1. The shown default values for CVBS_EQ_COEFx (x = 0 to 5) implement a flat equalizer response. Example of Table 60: If an attenuation of around 1 dB for video frequencies greater than 2 MHz is wanted, the following figure (see Figure 18) can be implemented. TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 51 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 001aaj780 0 resp(f) (dB) -0.4 -0.8 -1.2 -1.6 -2.0 0 1 2 3 4 5 6 f (MHz) 7 Fig 18. Example for the programmable video equalizer Table 61. TDA8296 Product data sheet Coefficients used in video equalizer example Symbol Value CVBS_EQ_COEF0[11:0] 005h CVBS_EQ_COEF1[11:0] FFDh CVBS_EQ_COEF2[11:0] 016h CVBS_EQ_COEF3[11:0] FFFh CVBS_EQ_COEF4[11:0] 018h CVBS_EQ_COEF5[11:0] 39Ch All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 52 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 10. Limiting values Table 62. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134).[1][2][3] Symbol Parameter VDDD(1V2) Conditions Min Max Unit digital supply voltage (1.2 V) -0.5 +1.5 V VDDDR(3V3) ring digital supply voltage (3.3 V) -0.5 +4.6 V VDDA(ADC)(1V2) ADC analog supply voltage (1.2 V) -0.5 +1.5 V VDDA(PLL)(1V2) PLL analog supply voltage (1.2 V) -0.5 +1.5 V VDDA(DAC)(3V3) DAC analog supply voltage (3.3 V) -0.5 +4.6 V Vi input voltage pins XIN, IF_POS and IF_NEG -0.5 +1.3 V digital input pins -0.5 +4.6 V - 300 C Tlead lead temperature Ptot total power dissipation - 0.5 W Tstg storage temperature -40 +125 C Tj junction temperature - +125 C Tamb ambient temperature -20 +85 C VESD electrostatic discharge voltage - 1000 V - 4000 V Tamb = 85 C all pins: Field ind. Charge Device Model (FCDM) [4] Human Body Model (HBM) [1] Stresses above the absolute maximum ratings may cause permanent damage to the device. Exposure to absolute maximum ratings conditions for extended periods may affect device reliability. [2] Tj depends on the assembly condition of the package and especially on the design of the PCB. The application mounting must be done in such a way that the maximum junction temperature Tj(max) is never exceeded. [3] No power sequence requirement [4] Class IV according to EIA/JESD22-C101. 11. Thermal characteristics Table 63. Thermal characteristics Symbol Parameter Conditions Typ Unit Rth(j-a) thermal resistance from junction to ambient in still air 36.8 K/W The thermal resistance depends strongly on the nature of the PCB used in the application and on its design. The thermal resistance given in Table 63 corresponds to the value that can be measured on a multilayer PCB (4 layers) as defined by EIA/JESD51-2. This value is given for information only. The junction temperature influences strongly the reliability of an IC. The PCB used in the application contributes on a large part to the overall thermal characteristic. It must therefore be designed to insure that the junction temperature of the IC never exceeds Tj(max) = 125 C at the maximum ambient temperature. The IC has to be soldered to ground with its die-attached paddle. Plenty of vias are recommended to remove the heat. TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 53 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 12. Characteristics Table 64. Characteristics Power supplies 3.3 V, 1.2 V; Tamb = 25 C; PC/SC1 for L and M = 10 dB, all others 13 dB; nominal residual picture carrier of 3 % for L/L' , 10 % for M, 10 % for B/G, 12.5 % for D/K, 20 % for I; FM/AM modulation = 54 %, 1 kHz modulation frequency; measured in application PCB (see Figure 22 and Figure 23) with 16 MHz crystal frequency, terminated with 75 (CVBS) and 1 k (SSIF/audio). Operation mode set via easy programming (Section 9.3.1), otherwise stated. Low IF input signal at -3dB full scale, input frequencies as defined under row header IF input. Symbol Parameter Conditions Min Typ Max Unit VDD(1V2) supply voltage (1.2 V) digital and analog 1.1 1.2 1.3 V VDD(3V3) supply voltage (3.3 V) digital and analog 3.0 3.3 3.6 V IDD(tot)(1V2) total supply current (1.2 V) - 49 - mA IDD(tot)(3V3) total supply current (3.3 V) - 65 - mA Ptot total power dissipation default settings; fs = 54 MHz at ADC; DAC application in accordance to Figure 23 - 270 - mW fs = 54 MHz at ADC; DAC application in accordance to Figure 24 - 150 - mW Standby mode - 5 8 mW Power supply Digital I/Os VIH HIGH-level input voltage all inputs (except pin XIN); including voltage on outputs in 3-state mode 0.7 x VDD(3V3) - 6.0 V VIL LOW-level input voltage all inputs (except pin XIN); including voltage on outputs in 3-state mode - 0.8 V VOH HIGH-level output voltage source current 4 mA VDD(3V3) - 0.4 - - V VOL LOW-level output voltage sink current 4 mA - - 0.4 V Ci input capacitance - - 5 pF - 108 - MHz - - 200 10-6 - 16 - MHz - Master clock fclk(o)(PLL) PLL output clock frequency f/fclk relative frequency deviation from clock frequency [1] Reference frequency in Slave mode fclk(ext) external clock frequency Vi(RMS) RMS input voltage AC coupled 200 250 - mV SRr rising slew rate external clock 30 - - mV/ns tjit(cc) cycle-to-cycle jitter time RMS value - 12.5 - ps Ci input capacitance on pin XIN - 3 - pF TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 54 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 64. Characteristics ...continued Power supplies 3.3 V, 1.2 V; Tamb = 25 C; PC/SC1 for L and M = 10 dB, all others 13 dB; nominal residual picture carrier of 3 % for L/L' , 10 % for M, 10 % for B/G, 12.5 % for D/K, 20 % for I; FM/AM modulation = 54 %, 1 kHz modulation frequency; measured in application PCB (see Figure 22 and Figure 23) with 16 MHz crystal frequency, terminated with 75 (CVBS) and 1 k (SSIF/audio). Operation mode set via easy programming (Section 9.3.1), otherwise stated. Low IF input signal at -3dB full scale, input frequencies as defined under row header IF input. Symbol Parameter Conditions Min Typ Max Unit - 16 - MHz Reference frequency in Oscillator mode (with a crystal) fxtal crystal frequency fxtal/fxtal relative crystal frequency variation temperature, ageing and spreading - - 200 10-6 Vi(p-p) peak-to-peak input voltage for full-scale ADC input (0 dBFS) 0.7 0.8 0.9 V Ri(dif) differential input resistance 10 15 - k Ci(dif) differential input capacitance - 2 3 pF Vi input voltage operational input related to ADC full scale; all standards; sum of all signals -3 -3 -3 dBFS fi input frequency PC / SC1 M/N standard - 5.40 / 0.90 - MHz B standard - 6.40 / 0.90 - MHz G/H standard - 6.75 / 1.25 - MHz I standard - 7.25 / 1.25 - MHz D/K standard - 6.85 / 0.35 - MHz L standard - 6.75 / 0.25 - MHz L-accent standard - 1.25 / 7.75 - MHz FM radio - 1.25 - MHz Hilbert filter stop-band -60 - - dB -40 - - dB -40 - - dB ultrawide - 280 - kHz superwide - 130 - kHz wide - 60 - kHz medium - 30 - kHz - 15 - kHz - 830 - kHz 115 117 - % 13 - - kHz IF input IF selectivity sup(stpb) stop-band suppression decimation filter stop-band notch for NSC (NPC for L-accent standard) [2] Carrier recovery FPLL B-3dB(cl) closed-loop -3 dB bandwidth narrow fpullin pull-in frequency range mover(PC) picture carrier over modulation index black for L/L-accent standard; flat field white else fstep(AFC) AFC step frequency 128 steps TDA8296 Product data sheet [3] [3] All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 55 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 64. Characteristics ...continued Power supplies 3.3 V, 1.2 V; Tamb = 25 C; PC/SC1 for L and M = 10 dB, all others 13 dB; nominal residual picture carrier of 3 % for L/L' , 10 % for M, 10 % for B/G, 12.5 % for D/K, 20 % for I; FM/AM modulation = 54 %, 1 kHz modulation frequency; measured in application PCB (see Figure 22 and Figure 23) with 16 MHz crystal frequency, terminated with 75 (CVBS) and 1 k (SSIF/audio). Operation mode set via easy programming (Section 9.3.1), otherwise stated. Low IF input signal at -3dB full scale, input frequencies as defined under row header IF input. Symbol Parameter Conditions Min Typ Max Unit IF demodulation (video equalizer in Flat mode) BT(tot) total transition bandwidth Nyquist filter; all standards - 1 - MHz sup(stpb) stop-band suppression Nyquist filter; all standards -60 - - dB video low-pass filter (M/N, B/G/H, I, D/K, L/L-accent standard) - -60 - dB M/N standard - 3.8 - MHz B/G/H, I, D/K, L/L-accent standard - 4.8 - MHz - 20 40 ns 400 - - Hz 0.2 - - Hz negative modulation (all standards except L/L-accent) - 3 - ms positive modulation (L/L-accent standard) - 100 - ms -20 - +48 dB with TDA1827x; positive modulation - 3 000 - ms with TDA1827x; negative modulation - 600 - ms 0.9 1.0 1.1 kHz Bvideo(-1dB) tripple(GDE) -1 dB video bandwidth group delay equalizer ripple peak value for B/G/H half, time D/K half, I flat, M (FCC) full, L/L-accent full standard Digital IF AGC (internal loop) B-3dB(cl) closed-loop -3 dB bandwidth negative modulation (all standards except L/L-accent) [4] positive modulation (L/L-accent standard) tresp GAGC response time 20 dB level change; video settled within 3 dB AGC gain range Tuner IF AGC (external loop) tresp f-3dB(lpf) response time low-pass filter -3 dB frequency TDA8296 Product data sheet at 60 dBV (RMS) PC input; 20 dB level change; video settled within 3 dB IF AGC postfilter [5] All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 56 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 64. Characteristics ...continued Power supplies 3.3 V, 1.2 V; Tamb = 25 C; PC/SC1 for L and M = 10 dB, all others 13 dB; nominal residual picture carrier of 3 % for L/L' , 10 % for M, 10 % for B/G, 12.5 % for D/K, 20 % for I; FM/AM modulation = 54 %, 1 kHz modulation frequency; measured in application PCB (see Figure 22 and Figure 23) with 16 MHz crystal frequency, terminated with 75 (CVBS) and 1 k (SSIF/audio). Operation mode set via easy programming (Section 9.3.1), otherwise stated. Low IF input signal at -3dB full scale, input frequencies as defined under row header IF input. Symbol Parameter Conditions Min Typ Max Unit peak-to-peak output voltage negative PC modulation (all standards except L/L-accent); 75 DC load; sync-white modulation 65 % - 0.7 - V nominal 0.9 1.0 1.1 V 115 % - 1.0 - V 65 % - 0.7 - V nominal 0.9 1.0 1.1 V 115 % - 1.0 - V all standards except M/N 4.7 4.85 - MHz M/N standard 3.8 3.9 - MHz -5 - +4.5 dB CVBS output Vo(p-p) positive PC modulation (L/L-accent standard); 75 DC load; sync-white modulation Bvideo(-3dB) -3 dB video bandwidth overall video response; CVBS equalizer flat resp(f) frequency response video equalizer; 8 equally spaced settings; value at 3.9 MHz Gdif differential gain "ITU-T J.63 line 330" - 1.5 5 % dif differential phase "ITU-T J.63 line 330" - 1.0 3 deg Vvideo/Vsync video voltage to sync voltage ratio video DAC application according to Figure 23 1.9 2.33 3.0 Vsync synchronization voltage video DAC application according to Figure 23 160 200 240 mV - 1 2 % all standards except L/L-accent - 1 3 % L/L-accent standard in peak white AGC detection - 1 5 % - 2 5 % [6] Vstlt/VCVBS(p-p) synchronization tilt voltage to peak-to-peak CVBS voltage ratio Vftlt/VCVBS(p-p) frame tilt voltage to peak-to-peak CVBS voltage ratio Vtro/Vtro relative transient response 2T pulse overshoot voltage variation TDA8296 Product data sheet [7] All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 57 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 64. Characteristics ...continued Power supplies 3.3 V, 1.2 V; Tamb = 25 C; PC/SC1 for L and M = 10 dB, all others 13 dB; nominal residual picture carrier of 3 % for L/L' , 10 % for M, 10 % for B/G, 12.5 % for D/K, 20 % for I; FM/AM modulation = 54 %, 1 kHz modulation frequency; measured in application PCB (see Figure 22 and Figure 23) with 16 MHz crystal frequency, terminated with 75 (CVBS) and 1 k (SSIF/audio). Operation mode set via easy programming (Section 9.3.1), otherwise stated. Low IF input signal at -3dB full scale, input frequencies as defined under row header IF input. Symbol Parameter Conditions IM(blue) intermodulation suppression (blue) carrier levels related to PC sync; PC = -3.2 dB; CC = -19.2 dB; SC = -13 dB IM(yellow) intermodulation suppression (yellow) Min Typ Max Unit 1.1 MHz (related to black-to-white in RMS, equals CC + 3.6 dB) - 67 - dB 3.3 MHz (related to CC) - 77 - dB 1.1 MHz (related to black-to-white in RMS, equals CC + 3.6 dB) - 70 - dB 3.3 MHz (related to CC) - 78 - dB 57 60 - dB - 39 - dB - 47 - dB - 65 - dB - 37 - dB - 56 - dB carrier levels related to PC sync; PC = -10 dB; CC = -19.2 dB; SC = -13 dB (S/N)w weighted signal-to-noise ratio all standards; unified weighting filter ("ITU-T J.61"); PC at -6 dBFS PSRR power supply rejection ratio fripple = 70 Hz; 100 mV (p-p); video signal: gray; level: 50 %; TDA8296 stand alone; input positive video modulation; L standard; 1.2 V positive video modulation; L standard; 3.3 V [8] negative video modulation; B standard; 1.2 V negative video modulation; B standard; 3.3 V sup(f)L(unw) unwanted leakage frequency suppression TDA8296 Product data sheet 4.8 MHz video modulation; related to black-to-white in 10 MHz to 200 MHz band, wanted signal (peak-to-peak) and unwanted signal (RMS) [8] All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 58 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 64. Characteristics ...continued Power supplies 3.3 V, 1.2 V; Tamb = 25 C; PC/SC1 for L and M = 10 dB, all others 13 dB; nominal residual picture carrier of 3 % for L/L' , 10 % for M, 10 % for B/G, 12.5 % for D/K, 20 % for I; FM/AM modulation = 54 %, 1 kHz modulation frequency; measured in application PCB (see Figure 22 and Figure 23) with 16 MHz crystal frequency, terminated with 75 (CVBS) and 1 k (SSIF/audio). Operation mode set via easy programming (Section 9.3.1), otherwise stated. Low IF input signal at -3dB full scale, input frequencies as defined under row header IF input. Symbol Parameter Conditions Min Typ Max Unit M standard - 4.5 - MHz B/G/H standard - 5.5 - MHz I standard - 6.0 - MHz D/K/L/L-accent standard - 6.5 - MHz FM radio - 5.5 - MHz M standard 105 120 135 mV B standard 100 115 130 mV G/H standard 100 115 130 mV D/K standard 95 110 125 mV I standard 100 115 130 mV L standard 95 110 125 mV L-accent standard 95 110 125 mV FM radio (single carrier) 100 115 130 mV M standard; 54 % modulation degree (13.5 kHz FM deviation before pre-emphasis) 98 126 135 mV B, G/H, I, D/K standard; 54 % modulation degree (27 kHz FM deviation before pre-emphasis) 107 133 144 mV L/L-accent standard; AM; m = 54 %; gain +6 dB 158 176 196 mV FM radio; 30 % modulation degree (22.5 kHz FM deviation before pre-emphasis) 51 54 60 mV - 425 - mV SSIF/mono sound output fo(SSIF) Vo(SSIF)(RMS) Vo(AF)(RMS) SSIF output frequency RMS SSIF output voltage RMS AF output voltage SC1 or FM radio carrier 1 k DC or AC load; no modulation; PC / SC1 = 13 dB; Cs = 220 pF 1 k DC or AC load; FM; gain 0 dB high Deviation mode (D/K standard China); FM deviation before pre-emphasis 400 kHz; sound level setting: -12 dB TDA8296 Product data sheet [9] [10] All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 59 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 64. Characteristics ...continued Power supplies 3.3 V, 1.2 V; Tamb = 25 C; PC/SC1 for L and M = 10 dB, all others 13 dB; nominal residual picture carrier of 3 % for L/L' , 10 % for M, 10 % for B/G, 12.5 % for D/K, 20 % for I; FM/AM modulation = 54 %, 1 kHz modulation frequency; measured in application PCB (see Figure 22 and Figure 23) with 16 MHz crystal frequency, terminated with 75 (CVBS) and 1 k (SSIF/audio). Operation mode set via easy programming (Section 9.3.1), otherwise stated. Low IF input signal at -3dB full scale, input frequencies as defined under row header IF input. Symbol Parameter Conditions hr(AF) AF headroom before clipping; 1 k DC or AC load deemp Min Typ Max Unit M standard; related to 25 kHz peak deviation before pre-emphasis - 7 - dB B, G/H, I, D/K standard; related to 50 kHz peak deviation before pre-emphasis - 7 - dB L/L-accent standard; PC / SC1 ratio for start of audio output clipping; AM; m = 100 %; related to mean SC1 - 9 - dB FM radio; 30 % modulation degree related to 22.5 kHz peak deviation before pre-emphasis - 9 - dB - 75 - s - 50 - s L/L-accent standard - 30 - kHz M-BTSC standard - 140 - kHz FM; for 50 kHz deviation before pre-emphasis (25 kHz for M standard) - 0.15 0.3 % AM; m = 80 % - 0.5 1 % AM 20 27 - kHz FM 40 50 - kHz of FM demodulator; AM: f = 1 kHz; m = 54 % referenced to 27 kHz FM deviation 40 51 - dB de-emphasis time constant M/N standard (mono); FM radio USA B/G/H, I, D/K standard; FM radio Europe B-3dB THD -3 dB bandwidth total harmonic distortion BAF(-3dB) -3 dB AF bandwidth AM AM suppression TDA8296 Product data sheet audio low-pass filter All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 60 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 64. Characteristics ...continued Power supplies 3.3 V, 1.2 V; Tamb = 25 C; PC/SC1 for L and M = 10 dB, all others 13 dB; nominal residual picture carrier of 3 % for L/L' , 10 % for M, 10 % for B/G, 12.5 % for D/K, 20 % for I; FM/AM modulation = 54 %, 1 kHz modulation frequency; measured in application PCB (see Figure 22 and Figure 23) with 16 MHz crystal frequency, terminated with 75 (CVBS) and 1 k (SSIF/audio). Operation mode set via easy programming (Section 9.3.1), otherwise stated. Low IF input signal at -3dB full scale, input frequencies as defined under row header IF input. Symbol Parameter Conditions Min Typ Max Unit (S/N)w(AF) AF weighted signal-to-noise ratio via internal mono sound demodulator; "ITU-R BS.468-4"; FM mode related to 27 kHz deviation before pre-emphasis; 10 % residual PC; SC1 black picture 52 54 - dB flat field white picture 52 54 - dB 6 kHz sine wave picture 52 54 - dB 250 kHz square wave picture 52 54 - dB crosshatch picture 52 54 - dB 52 54 - dB black picture 40 44 - dB flat field white picture 41 44 - dB color bar picture 40 44 - dB - 45 - dB color bar picture via internal mono sound demodulator; (audio gain +6 dB) "ITU-R BS.468-4"; AM; m = 54 %; 3 % residual PC; SC1 via internal mono sound demodulator; "ITU-R BS.468-4"; FM Radio mode; 22.5 kHz deviation TDA8296 Product data sheet [11] All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 61 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 64. Characteristics ...continued Power supplies 3.3 V, 1.2 V; Tamb = 25 C; PC/SC1 for L and M = 10 dB, all others 13 dB; nominal residual picture carrier of 3 % for L/L' , 10 % for M, 10 % for B/G, 12.5 % for D/K, 20 % for I; FM/AM modulation = 54 %, 1 kHz modulation frequency; measured in application PCB (see Figure 22 and Figure 23) with 16 MHz crystal frequency, terminated with 75 (CVBS) and 1 k (SSIF/audio). Operation mode set via easy programming (Section 9.3.1), otherwise stated. Low IF input signal at -3dB full scale, input frequencies as defined under row header IF input. Symbol Parameter Conditions Min Typ Max Unit (S/N)w(SC1) first sound carrier weighted via external SSIF sound signal-to-noise ratio demodulator in Dual mode; "ITU-R BS.468-4"; FM mode related to 27 kHz deviation before pre-emphasis; 10 % residual PC black picture - 58 - dB flat field white picture - 57 - dB 6 kHz sine wave picture - 57 - dB 250 kHz square wave picture - 58 - dB crosshatch picture - 52 - dB color bar picture - 58 - dB black picture - 44 - dB flat field white picture - 44 - dB color bar picture - 44 - dB black picture - 56 - dB flat field white picture - 55 - dB 6 kHz sine wave picture - 55 - dB 250 kHz square wave picture - 51 - dB crosshatch picture - 51 - dB color bar picture - 56 - dB - 55 - dB via SSIF sound demodulator; "ITU-R BS.468-4"; AM; m = 54 %; 3 % residual PC (S/N)w(SC2) (S/N)w second sound carrier weighted signal-to-noise ratio weighted signal-to-noise ratio TDA8296 Product data sheet via external SSIF sound demodulator in Dual mode; "ITU-R BS.468-4"; FM mode related to 27 kHz deviation before pre-emphasis; 10 % residual PC FM radio; via SSIF sound demodulator in Mono mode; "ITU-R BS.468-4"; 22.5 kHz deviation All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 62 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 64. Characteristics ...continued Power supplies 3.3 V, 1.2 V; Tamb = 25 C; PC/SC1 for L and M = 10 dB, all others 13 dB; nominal residual picture carrier of 3 % for L/L' , 10 % for M, 10 % for B/G, 12.5 % for D/K, 20 % for I; FM/AM modulation = 54 %, 1 kHz modulation frequency; measured in application PCB (see Figure 22 and Figure 23) with 16 MHz crystal frequency, terminated with 75 (CVBS) and 1 k (SSIF/audio). Operation mode set via easy programming (Section 9.3.1), otherwise stated. Low IF input signal at -3dB full scale, input frequencies as defined under row header IF input. Symbol Parameter Conditions PSRR power supply rejection ratio fripple = 70 Hz; 100 mV (p-p); video signal: gray; level: 50 %; TDA8296 stand alone FM sound; 1.2 V FM sound; 3.3 V [8] AM sound; 1.2 V AM sound; 3.3 V sup(f)L(unw) unwanted leakage frequency suppression related to SSIF (SC1) in 10 MHz to 200 MHz band wanted signal (peak-to-peak) and unwanted signal (RMS) [8] Min Typ Max Unit - 80 - dB - 39 - dB - 40 - dB - 38 - dB - 51 - dB [1] See Section 9.3.17 for PLL setting. [2] Standard dependent located at 6.9 MHz, 7.9 MHz, 8.3 MHz and 9.25 MHz. [3] The pull-in range can be doubled to 1 660 kHz by I2C-bus register like described in Table 16. Then the AFC read-out has 256 steps. [4] To counteract a fast IF level reduction, the digital IF AGC loop has a speed-up circuit for positive video modulation. [5] In the ordinary system application, this slow response is counteracted by the fast digital IF AGC loop. ADC clipping is practically avoided by fast-attack AGC characteristic. [6] Graph differential gain versus temperature. [7] HAD: 250 ns for M standard, 200 ns for others. [8] The values given are measured with an IF AGC time constant of 5 Hz. For that, capacitor C7 in Figure 19 must be chosen 220 nF instead of 2.2 nF. Doing so, the PSRR on 3.3 V together with the tuner can be improved. [9] SC2 is not listed, but supported for all world standards. [10] At high deviation mode at D/K standard, IF frequency has to be programmed, that SIF frequency is higher than 500 kHz (default: 350 kHz). [11] To set audio gain to +6 dB for internal sound demodulation, register 22h has to be programmed to 08h. TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 63 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 13. Application information 13.1 Typical application I2C-bus I2C-bus SDA_O SCL_O V-sync SDA SCL V_IOUTN VSYNC CVBS V_IOUTP IF_POS TDA1827x (1) (TUNER IC) TDA8296 IF_NEG SSIF S_IOUTP IF_AGC tuner IF AGC processed audio and video S_IOUTN XIN AUDIO AND VIDEO DECODER RSET reference frequency 008aaa140 (1) Input filter schematics see Figure 20 or Figure 21 Fig 19. Typical application of TDA8296 13.1.1 IF input application 100 nF 47 82 VSSA(ADC) IF_POS 39 pF 39 pF IF_NEG 40 1 TDA8296 2 82 100 nF 47 001aam375 Fig 20. IF input application for interlacing TDA1827x 100 nF 22 82 22 nF 68 pF 22 nF VSSA(ADC) IF_POS IF_NEG 1 40 TDA8296 2 82 100 nF 22 001aan141 Fig 21. IF input application TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 64 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 13.2 Detailed application diagrams 13.2.1 Main application diagram GND +3.3 V 10 IF_AGC GND Low IF in IF_NEG 2.2 VDDA(ADC)(1V2) +1.2 V 2.2 VDDD1(1V2) +1.2 V 10 k GPIO2/SDA_O (3) 31 (3) 32 GPIO1/SCL_O GPIO0/VSYNC 33 35 VDDDR(3V3) VSSDR i.c. 36 IF_AGC 37 38 40 39 i.c. n.c. VSSA(ADC) 150 k IF_POS 10 k GND 470 nF 470 nF 34 GND +3.3 V 1 30 2 29 3 28 4 27 5 26 TRST_N GND SDA 100 SCL 100 TCK GND (2) VSSD1 GND TDA8296 GND V_IOUT 1 S_IOUT +3.3 V GND SADDR0 220 nF 2.2 VDDD2(1V2) TMS +1.2 V GND TDI GND TDO 2.2 k RST_N 20 +3.3 V 100 nF Address select 470 nF (1) GND SADDR1 19 18 VDDA(DAC2)(3V3) S_IOUTP VSSA(DAC) 470 nF 17 21 RSET GND 22 10 11 VSSA(PLL) GND 9 16 (4) 23 S_IOUTN XOUT 220 nF 8 15 (4) VDDA(DAC1)(3V3) XIN 14 100 pF 24 V_IOUTP 16 MHz reference input 7 13 VDDA(PLL)(1V2) 25 V_IOUTN 10 +1.2 V 6 12 i.c. VSSD2 1 +3.3 V Address select Pin 20 Pin 19 Address GND GND 84h GND +3.3 V 86h +3.3 V GND 94h +3.3 V +3.3 V 96h 001aam371 (1) RRSET depends on application (2) PCB layout dependent (3) use of GPIO function not recommended (4) for clock/oscillator application refer to Figure 32 and Figure 33 Fig 22. Main application diagram TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 65 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 13.2.2 75 application This is the reference application for the data sheet characteristic. TDA8296 470 pF 75 75 470 pF 17 S_IOUTN RSET 1 k 16 S_IOUTP 14 V_IOUTP 13 V_IOUTN 11 75 Cs(1) 75 Cs(1) SSIF Out > 1 k terminated 75 CVBS Out 75 terminated 001aam372 (1) For Cs value please refer to Figure 14, for characteristics Cs = 220 pF is used Set value of B_DA_V[5:0] to 3Fh (part of register 0x35h) and value of B_DA_S[5:0] to 00h (part of register 0x36h) Fig 23. 75 load 13.2.3 100 application TDA8296 16 S_IOUTN V_IOUTN 17 S_IOUTP 14 V_IOUTP 13 RSET 11 SSIF Out 2 k 180 pF 100 180 pF 100 150 pF CVBS Out 100 150 pF 100 001aam373 Set value of B_DA_V[5:0] to 18h (part of register 0x35h) and value of B_DA_S[5:0] to 17h (part of register 0x36h) Fig 24. High ohmic load TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 66 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 13.2.4 Buffer application +5 V 47 F 100 nF TDA8296 17 200 S_IOUTP 16 S_IOUTN RSET 14 V_IOUTP 13 V_IOUTN 11 560 PBSS4140U 68 150 PBSS2515VS CVBS 75 Ohm (SCART) VIDEO DECODER 2 k 33 150 pF 150 pF 100 220 pF 100 33 150 33 001aam374 SSIF Out Set value of B_DA_V[5:0] to 18h (part of register 0x35h) and value of B_DA_S[5:0] to 17h (part of register 0x36h) Fig 25. Buffer application with 75 load 13.2.5 Layout recommendations 18.00 SDA-T (1) 4.7 k 4.7 k 4.7 k 10 2.2 n.c. SDA SCL 18.00 1.0 470 nF 75 270 pF 1.0 75 270 pF 75 75 470 nF 470 nF (2) n.c. TDA8296HN 470 pF 18 pF 18 pF 10 16 MHz 100 n.c. 470 pF 2.2 100 75 2.2 Low-IFn 470 nF 470 nF Low-IFp 4.7 k 39 pF 1 nF 39 pF 82 470 nF 82 47 1.0 k IF-AGC 47 150 k SCL-T SIFp CVBSp 001aam882 (1) Bottom layer (2) Top layer Fig 26. PCB pattern using circuit diagrams of Figure 20, Figure 22, Figure 23 and 16 MHz reference from XTAL TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 67 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio SDA-T (1) 4.7 k 4.7 k SCL 2.2 2.2 k 470 nF 270 pF 1.0 75 75 SDA 1.0 75 1.0 k 470 pF 470 nF 270 pF 10 pF 220 16 MHz-n (2) 470 pF 100 pF TDA8296HN 470 nF 10 16 MHz-p 100 nF 470 nF 100 2.2 470 nF Low-IFn 4.7 k 100 75 2.2 470 nF 75 Low-IFp 10 39 pF 4.7 k 39 pF 82 1 nF 82 47 470 nF IF-AGC 47 150 k SCL-T SIFp CVBSp 001aan108 (1) Bottom layer (2) Top layer Fig 27. PCB pattern using circuit diagrams of Figure 20, Figure 22, Figure 23 and 16 MHz reference from master 13.3 DAC connection The video and sound output signals are converted from IC internal digital domain to analog output signal domain by digital controlled current sources. therefore the Digital to Analog Conversion (DAC) is based on controlled current sources. the current sources of the video and sound DACs are operating in differential mode. Even though differential mode can be used, the typical application use case is single ended. Each output of the differential pair needs to be terminated by the same impedance to ground. The termination impedance converts the DAC output current to signal voltage. The full scale DAC current is defined by application resistor RRSET (connected between pin RSET and ground). Typical values of RRSET are 1 k and 2 k. Additionally the full scale DAC current can be adjusted between 50% and 100% via register 0x35h (bits B_DA_V[5:0]) and via register 0x36h (bits B_DA_S[5:0]). The full scale current is application dependent and needs to be matched to the termination (output voltage is product of DAC current and termination impedance value). The nominal peak-peak signal voltage should not exceed 1Vpp. The sum of AC an DC signal should not exceed 1.5V single ended. TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 68 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio The following relation gives the value of the full-scale current IFS in function of the bias resistance value and value of B_DA_V[5:0] (part of register 0x35h) and value of B_DA_S[5:0] (part of register 0x36h) (B_DA_V or B_DA_S): 1.216 V RSET 1 64 + B_DA_V/S I FS = ------------------------------ x --- x -------------------------------------- x 64 5 48 R RSET (2) 0 B_DA_V/S 63 For programming of B_DA_V see Table 50, for B_DA_S see Table 51. 001aam357 45 DAC current [mA] (1) 35 (2) 25 (3) 15 5 0 10 20 30 40 50 60 DAC reg (dec) 70 (1) IV_IOUTP for RRSET = 1 k (2) IV_IOUTP for RRSET = 1.5 k (3) IV_IOUTP for RRSET = 2 k Fig 28. TDA8296 calculated DAC characteristic The DAC signal range used for CVBS and sound signal is reduced to provide headroom. The signal headroom is shown in Figure 29 and Figure 30. The full scale DAC current corresponds to digital input value of 1034. For the pins VIOUT_P and SIOUT_P the corresponding signal shapes of CVBS and sound signal can be mapped linear to the full scale DAC current. For the CVBS signal the sync level is fixed, the white level depends also on register value CVBS_LVL[7:0]. For the sound signal the DC level is fixed. TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 69 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 10 bit DAC input relative numbers (%) 150 1023 (2) 818 120 100 % 20 136 (1) time 001aam628 (1) Sync level (2) White level (also dependent on CVBS_LVL[7:0] at address 1Eh) Fig 29. Internal CVBS signal in front of video DAC (typical characteristic) 10 bit DAC input relative numbers (%) 1023 100 799 78 512 56 % 225 50 22 time 001aam629 Fig 30. Internal SSIF signal in front of sound DAC (typical characteristic, also dependent on SSIF_LVL[7:0] at address 23h) Application hints for DAC supply: it is required to use de-coupling capacitors at VDDA(DAC1)(3V3) and VDDA(DAC2)(3V3) supplies of > 100nF. A decoupling capacitor at pin RSET is not allowed. The component RRSET should be placed close to the chip. TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 70 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 13.4 ADC connection The input signals of the ADC (IF_POS and IF_NEG) can be either AC coupled by means of two capacitors or connected directly to the inputs (DC coupled). In case of AC coupling, the DCIN bit (see Table 48) should be set to logic 0, which enables the internal resistive dividers between VDDA(ADC)(1V2) and VSSD1 to take care of the correct DC biasing of the input signals. In case the input signal is DC coupled, the input resistor network can be switched off by setting the DCIN bit to logic 1. When using the ADC in this mode, the Common mode level of the input signal should be at (0.5 / 1.2) x VDDA(ADC)(1V2) 200 mV. Please note that during power-down the DC biasing network at the input will be switched off in order to reduce current consumption. During Sleep mode however the resistor network will remain active. 13.5 Reset operation 13.5.1 Hardware reset minimum width at LOW is 4 x TXIN RST_N XIN TXIN the TDA8296 enters immediately in its reset mode TDA8296 normal operation starts after 4 falling edges of XIN 008aaa144 Fig 31. Hardware reset operation After a hardware reset, the registers are set to default (power-on reset values) according to Table 9. M/N standard is the default standard. 13.5.2 Software reset A software reset can be done each time something has been programmed. The software reset does not affect the content of the registers but clears the flip-flops in the design. For the activation of the software reset see Table 47 bit CLB. 13.6 Application hints The DAC application can be adapted to a wide range of application needs. The data sheet describes 3 different use cases as shown in Figure 23 to Figure 25. The default application (also used for specification) is shown in Figure 23. This application supports 75 DC termination for the video CVBS and > 1 k AC/DC termination for the SSIF or mono audio sound signal. This application is e.g. preferred for device evaluation. TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 71 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio In applications, where the impedance of the CVBS termination is high (e.g. >1 k), which is normally the case with audio/video processor, the video and sound DAC can operate with significant lower current. An application proposal (which leads to reduced power consumption) is shown in Figure 24. For application requirements, where both, connections to audio/video processor (with input impedance >1 k) and 75 termination (e.g. to SCART output), are needed in parallel, a buffer application can be used as sown in Figure 25). 13.7 Crystal connection The typical crystal frequency value is 16 MHz. The values of the passive components depend on crystal manufacturer. The oscillator can be set in two configurations depending on the origin of the crystal. Figure 32 describes the case of an crystal shared with the tuner and the TDA8296 (Slave mode), Figure 33 the case of an crystal dedicated to the TDA8296 (Oscillator mode). TDA8296 TDA8296 Rbias Rbias XIN XIN XTAL XOUT XOUT 100 nF C1 clock signal from tuner n.c. GND C2 GND 008aaa143 008aaa142 Slave mode Oscillator mode Fig 32. Reference clock application Fig 33. Oscillator application In Oscillator mode, only a crystal and the load capacitances C1 and C2 need to be connected externally since the feedback resistance is integrated on chip. For an accurate time reference it is advised to use the load capacitors as specified in Table 65. CL is the typical load capacitance of the crystal and is usually specified by the crystal manufacturer. Table 65. Crystal parameters together with external components Fundamental oscillation frequency Crystal load capacitance CL(xtal) (pF) Crystal series resistance Rs(xtal) () External load capacitors C1 (pF) C2 (pF) 1 MHz to 5 MHz 10 < 300 18 18 20 < 300 39 39 30 < 300 56 56 10 < 300 18 18 20 < 200 39 39 30 < 100 56 56 5 MHz to 10 MHz TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 72 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 65. Crystal parameters together with external components ...continued Fundamental oscillation frequency Crystal load capacitance CL(xtal) (pF) Crystal series resistance Rs(xtal) () External load capacitors C1 (pF) C2 (pF) 10 MHz to 15 MHz 10 < 160 18 18 20 < 60 39 39 15 MHz to 20 MHz 10 < 80 18 18 13.8 Alternative ADC sampling rates In combination with a tuner front-end an alternative ADC sampling rates could be necessary. Please refer to Table 66 The default register setting is adapted to 16 MHz reference frequency (either from crystal or external source) and a nominal fADC = 54 MHz. In case of crosstalk of clock related signals (e.g. n x 54 MHz) into the RF input of connected tuner circuit, the potential disturbance of the wanted TV channel can be avoided by switching to the alternative ADC clock frequencies of 50.75 MHz or 57.25 MHz. Table 66. Alternative ADC clocks Frequencies ADC SR 50.75 MHz 54.00 MHz 57.25 MHz Clock PLL 101.50 MHz 108.00 MHz 114.50 MHz Xtal frequency 16.00 MHz 16.00 MHz 16.00 MHz M 203 27 229 N 16 2 16 P 2 2 2 Register 2Bh 01h 01h 02h Register 38h 23h 23h 23h Register 3Eh 63h 63h 63h Register 3Fh 01h 01h 01h Register 40h CAh 1Ah E4h Register 41h 1Eh 02h 1Eh Register 41h 61h 61h 61h Divider Registers TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 73 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 14. Test information 14.1 Boundary scan interface ("IEEE Std. 1149.1") The TDA8296 implements a boundary scan architecture to allow access to, and control of, board test support features within integrated circuits through a TAP. The TAP controller is a synchronous state machine that controls the sequence of operations on the TAP circuitry when the TMS signal changes. All state transitions occur on the basis of the TMS value on the rising edge of TCK. The instruction register is a shift register based design. It decodes the test to be performed and/or the test data register to be accessed. The instructions are shifted into the register through the TDI and are latched as the current instruction at the completion of the shifting process. The TDA8296 boundary scan architecture includes: a TAP controller, a scannable instruction register and three scannable test data registers: a boundary scan register, a device ID register, and a bypass register. The supported instructions are: EXTEST, IDCODE, SAMPLE, INTEST, CLAMP, HIGHZ and BYPASS. The boundary scan register is composed of 16 cells (see Table 67). Each cell is associated either to an input pad, an output pad, a bidirectional pad or to the bidirectional or 3-state command itself. All cells are of `observe and control' type. The device ID register is a 32-bit identification register that is included in the scan register itself and contains the ID number. It is a fixed value that identifies the chip. ID number structure is: ID version [3:0] = 1h ID part number [15:0] = 224Ch ID manufacturer [11:1] = 015h ID mandatory [0] = 1h IDCODE [31:0] = 1224 C02Bh When the boundary scan function is not used, please connect the four dedicated input pins (TRST_N, TCK, TDI and TMS) to GND. TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 74 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio BOUNDARY SCAN REGISTER DEVICE ID REGISTER MUX BYPASS REGISTER control MUX FF TDO INSTRUCTION DECODE TDI INSTRUCTION REGISTER TMS TEST ACCESS PORT CONTROLLER TCK TRST_N select 3-state enable 001aac078 Fig 34. Boundary scan block diagram Table 67. Chain position Pad type Scan type Control signal IF_AGC [1] Bidir control/observe U1.vagc_cmd [2] Ctrl control/observe U1.vagc_cmd [3] Bidir control/observe U1.gpio0_cmd [4] Ctrl control/observe U1.gpio0_cmd [5] Bidir control/observe U1.gpio1_cmd [6] Ctrl control/observe U1.gpio1_cmd [7] Bidir control/observe U1.gpio2_cmd [8] Ctrl control/observe U1.gpio2_cmd [9] Bidir control/observe U1.sda_cmd [10] Ctrl control/observe U1.sda_cmd SCL [11] input control/observe - RST_N [12] input control/observe - SADDR1 [13] Ctrl control/observe U1.saddr1_cmd [14] Bidir control/observe U1.saddr1_cmd [15] Ctrl control/observe U0.saddr1_cmd [16] Bidir control/observe U0.saddr1_cmd GPIO0 GPIO1 GPIO2 SDA SADDR0 TDA8296 Product data sheet Boundary scan register list Pad signal All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 75 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 68. Boundary scan electrical characteristics Symbol Parameter Conditions Min Typ Max Unit Tcy cycle time TCK 25 - - ns tsu set-up time TDI and TMS 0 - - ns th hold time TDI and TMS 4 - - ns td(TDO) delay time on pin TDO on 50 pF - - 12 ns Tcy TCK tsu th TDI, TMS td TDO 001aac079 Fig 35. Boundary scan timing diagram TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 76 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 15. Package outline HVQFN40: plastic thermal enhanced very thin quad flat package; no leads; 40 terminals; body 6 x 6 x 0.85 mm A B D SOT618-1 terminal 1 index area A E A1 c detail X C e1 e 1/2 e 20 y y1 C v M C A B w M C b 11 L 21 10 e e2 Eh 1/2 1 e 30 terminal 1 index area 40 31 Dh X 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A(1) max. A1 b c D(1) Dh E(1) Eh e e1 e2 L v w y y1 mm 1 0.05 0.00 0.30 0.18 0.2 6.1 5.9 4.25 3.95 6.1 5.9 4.25 3.95 0.5 4.5 4.5 0.5 0.3 0.1 0.05 0.05 0.1 Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC JEITA SOT618-1 --- MO-220 --- EUROPEAN PROJECTION ISSUE DATE 01-08-08 02-10-22 Fig 36. Package outline SOT618-1 (HVQFN40) TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 77 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 16. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 "Surface mount reflow soldering description". 16.1 Introduction to soldering Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization. 16.2 Wave and reflow soldering Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following: * Through-hole components * Leaded or leadless SMDs, which are glued to the surface of the printed circuit board Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are: * * * * * * Board specifications, including the board finish, solder masks and vias Package footprints, including solder thieves and orientation The moisture sensitivity level of the packages Package placement Inspection and repair Lead-free soldering versus SnPb soldering 16.3 Wave soldering Key characteristics in wave soldering are: * Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave * Solder bath specifications, including temperature and impurities TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 78 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 16.4 Reflow soldering Key characteristics in reflow soldering are: * Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 37) than a SnPb process, thus reducing the process window * Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board * Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 69 and 70 Table 69. SnPb eutectic process (from J-STD-020C) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 < 2.5 235 220 2.5 220 220 Table 70. Lead-free process (from J-STD-020C) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 to 2 000 > 2 000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 37. TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 79 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio maximum peak temperature = MSL limit, damage level temperature minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 37. Temperature profiles for large and small components For further information on temperature profiles, refer to Application Note AN10365 "Surface mount reflow soldering description". 17. Abbreviations Table 71. TDA8296 Product data sheet Abbreviations Acronym Description ADC Analog-to-Digital Converter AFC Automatic Frequency Control AGC Automatic Gain Control CC Color Carrier CMOS Complementary Metal-Oxide Semiconductor CORDIC COordinate Rotation DIgital Computer CVBS Color Video Blanking Signal DAC Digital-to-Analog Converter DTO Digitally Tuned Oscillator DVD Digital Versatile Disc FIR Finite Impulse Response FPLL Frequency Phase-Locked Loop FS Full Scale GPIO General Purpose Input Output H/V Horizontal and Vertical HAD Half Amplitude Duration IC Integrated Circuit ID IDentification IF Intermediate Frequency All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 80 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Table 71. Abbreviations ...continued Acronym Description NPC Neighbor Picture Carrier NSC Neighbor Sound Carrier PC Picture Carrier PCB Printed-Circuit Board PLL Phase-Locked Loop POR Power-On Reset PWM Pulse Width Modulation QSS Quasi Split Sound SAW Surface Acoustic Wave SC Sound Carrier SCART Syndicat des Constructeurs d'Appareils Radiorecepteurs et Televiseurs Radio and Television Receiver Manufacturers' Association SMD Surface Mounted Device SSIF Second Sound Intermediate Frequency TAP Test Access Port VITS Vertical Interval Test Signal 18. Revision history Table 72. Revision history Document ID Release date Data sheet status Change notice Supersedes TDA8296 v.1 20110303 Product data sheet - - TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 81 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 19. Legal information 19.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term `short data sheet' is explained in section "Definitions". [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 19.2 Definitions Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification -- The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 19.3 Disclaimers Limited warranty and liability -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors' aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer's sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer's applications and products planned, as well as for the planned application and use of customer's third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer's applications or products, or the application or use by customer's third party customer(s). Customer is responsible for doing all necessary testing for the customer's applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer's third party customer(s). NXP does not accept any liability in this respect. Limiting values -- Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale -- NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer's general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. Right to make changes -- NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. No offer to sell or license -- Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Suitability for use -- NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or Export control -- This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities. TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 82 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio Quick reference data -- The Quick reference data is an extract of the product data given in the Limiting values and Characteristics sections of this document, and as such is not complete, exhaustive or legally binding. Non-automotive qualified products -- Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors' warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors' specifications such use shall be solely at customer's own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors' standard warranty and NXP Semiconductors' product specifications. 19.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. I2C-bus -- logo is a trademark of NXP B.V. Silicon Tuner -- is a trademark of NXP B.V. 20. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 83 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 21. Tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. Table 19. Table 20. Table 21. Table 22. Table 23. Table 24. Table 25. Table 26. Table 27. Table 28. Table 29. Quick reference data . . . . . . . . . . . . . . . . . . . . .3 Ordering information . . . . . . . . . . . . . . . . . . . . .5 Pin allocation table . . . . . . . . . . . . . . . . . . . . . . .7 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . .8 Pin type description . . . . . . . . . . . . . . . . . . . . .10 Address format . . . . . . . . . . . . . . . . . . . . . . . . .13 I2C-bus transfer description . . . . . . . . . . . . . . .13 I2C-bus transfer description . . . . . . . . . . . . . . .14 I2C-bus register reference . . . . . . . . . . . . . . . .15 I2C-bus registers . . . . . . . . . . . . . . . . . . . . . . .18 STANDARD register (address 00h) bit description . . . . . . . . . . . . . . . . . . . . . . . . .23 EASY_PROG register (address 01h) bit description . . . . . . . . . . . . . . . . . . . . . . . . .23 Easy programming values . . . . . . . . . . . . . . . .24 DIV_FUNC register (address 02h) bit description . . . . . . . . . . . . . . . . . . . . . . . . .25 ADC_HEADR register (address 03h) bit description . . . . . . . . . . . . . . . . . . . . . . . . .25 PC_PLL_FUNC register (address 04h) bit description . . . . . . . . . . . . . . . . . . . . . . . . .26 DTO_PC_LOW, DTO_PC_MID and DTO_PC_HIGH register (address 09h to 0Bh) bit description . . . . . . . .26 Values of DTO_PC per TV standard at 54 MHz sampling frequency . . . . . . . . . . . . .27 DTO_SC_LOW, DTO_SC_MID and DTO_SC_HIGH register (address 0Ch to 0Eh) bit description . . . . . . . . . . . . . . . . . . . . . . . . .27 Values for SSIF mode at 54 MHz sampling frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 FILTERS_1 register (address 0Fh) bit description . . . . . . . . . . . . . . . . . . . . . . . . .28 FILTERS_2 register (address 10h) bit description . . . . . . . . . . . . . . . . . . . . . . . . .30 GRP_DELAY register (address 11h) bit description . . . . . . . . . . . . . . . . . . . . . . . . .31 D_IF_AGC_SET_1 register (address 12h) bit description . . . . . . . . . . . . . . . . . . . . . . . . .32 D_IF_AGC_SET_2 register (address 13h) bit description . . . . . . . . . . . . . . . . . . . . . . . . .32 T_IF_AGC_SET register (address 15h) bit description . . . . . . . . . . . . . . . . . . . . . . . . .32 T_IF_AGC_LIM register (address 16h) bit description . . . . . . . . . . . . . . . . . . . . . . . . .33 T_IF_AGC_FORCE register (address 17h) bit description . . . . . . . . . . . . . . . . . . . . . . . . .33 V_SYNC_DEL register (address 1Ch) bit description . . . . . . . . . . . . . . . . . . . . . . . . . 34 Table 30. CVBS_SET register (address 1Dh) bit description . . . . . . . . . . . . . . . . . . . . . . . . . 34 Table 31. CVBS_LEVEL register (address 1Eh) bit description . . . . . . . . . . . . . . . . . . . . . . . . . 35 Table 32. CVBS_EQ register (address 1Fh) bit description . . . . . . . . . . . . . . . . . . . . . . . . . 35 Table 33. SSIF_MUTE register (address 05h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . 36 Table 34. SOUNDSET_1 register (address 20h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . 36 Table 35. SOUNDSET_2 register (address 21h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . 37 Table 36. SOUND_LEVEL register (address 22h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . 38 Table 37. SSIF_LEVEL register (address 23h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . 39 Table 38. ADC_SAT register (address 24h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . 40 Table 39. AFC register (address 25h) bit description . . . 41 Table 40. Calculation of frequency deviation from AFC value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Table 41. HVPLL_STAT register (address 26h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . 42 Table 42. D_IF_AGC_STAT register (address 27h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . 43 Table 43. T_IF_AGC_STAT register (address 28h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . 43 Table 44. ALT_FILT_COEF register (address 2Bh) bit description . . . . . . . . . . . . . . . . . . . . . . . . . 43 Table 45. SSIF_AGC_STAT register (address 2Dh) bit description . . . . . . . . . . . . . . . . . . . . . . . . . 43 Table 46. IDENTITY register (address 2Fh) bit description . . . . . . . . . . . . . . . . . . . . . . . . . 43 Table 47. CLB_STDBY register (address 30h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . 43 Table 48. ADC_CTL register (address 33h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . 44 Table 49. ADC_CTL_2 register (address 34h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . 44 Table 50. VIDEODAC_CTL register (address 35h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . 45 Table 51. AUDIODAC_CTL register (address 36h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . 46 Table 52. DAC_REF_CLK_CTL register (address 37h) bit description . . . . . . . . . . . . . . 46 Table 53. PLL_REG07, PLL_REG08, PLL_REG09 and PLL_REG10 register (address 3Fh to 42h) continued >> TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 84 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio bit description . . . . . . . . . . . . . . . . . . . . . . . . .46 Table 54. GPIOREG_0 register (address 44h) bit description . . . . . . . . . . . . . . . . . . . . . . . . .47 Table 55. GPIOREG_1 register (address 45h) bit description . . . . . . . . . . . . . . . . . . . . . . . . .47 Table 56. HVPLL signal configuration . . . . . . . . . . . . . . .48 Table 57. GPIOREG_2 register (address 46h) bit description . . . . . . . . . . . . . . . . . . . . . . . . .48 Table 58. GD_EQ_SECTx_C1 and GD_EQ_SECTx_C2 (x = 1 to 4) register (address 4Bh to 52h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . .49 Table 59. Coefficients used in group delay equalizer example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 Table 60. CVBS_EQ_COEFx_LOW and CVBS_EQ_COEFx_HIGH (x = 0 to 5) register (address 57h to 62h) bit description . . . . . . . .50 Table 61. Coefficients used in video equalizer example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 Table 62. Limiting values . . . . . . . . . . . . . . . . . . . . . . . . .53 Table 63. Thermal characteristics . . . . . . . . . . . . . . . . . .53 Table 64. Characteristics . . . . . . . . . . . . . . . . . . . . . . . . .54 Table 65. Crystal parameters together with external components . . . . . . . . . . . . . . . . . . . . . . . . . . .72 Table 66. Alternative ADC clocks . . . . . . . . . . . . . . . . . . .73 Table 67. Boundary scan register list . . . . . . . . . . . . . . .75 Table 68. Boundary scan electrical characteristics . . . . .76 Table 69. SnPb eutectic process (from J-STD-020C) . . .79 Table 70. Lead-free process (from J-STD-020C) . . . . . .79 Table 71. Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . .80 Table 72. Revision history . . . . . . . . . . . . . . . . . . . . . . . .81 TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 85 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 22. Figures Fig 1. Fig 2. Fig 3. Fig 4. Fig 5. Fig 6. Fig 7. Fig 8. Fig 9. Fig 10. Fig 11. Fig 12. Fig 13. Fig 14. Fig 15. Fig 16. Fig 17. Fig 18. Fig 19. Fig 20. Fig 21. Fig 22. Fig 23. Fig 24. Fig 25. Fig 26. Fig 27. Fig 28. Fig 29. Fig 30. Fig 31. Fig 32. Fig 33. Fig 34. Fig 35. Fig 36. Fig 37. Functional diagram of TDA8296 . . . . . . . . . . . . . .6 Pin configuration for HVQFN40 . . . . . . . . . . . . . . .7 I2C-bus Write mode . . . . . . . . . . . . . . . . . . . . . . .13 Examples I2C-bus Write mode. . . . . . . . . . . . . . .13 I2C-bus Read mode . . . . . . . . . . . . . . . . . . . . . . .14 Example I2C-bus Read mode . . . . . . . . . . . . . . .14 TDA8296 DTO_PC characteristic . . . . . . . . . . . .27 TDA8296 DTO_SC characteristic . . . . . . . . . . . .28 Video low-pass filters for sound carrier suppression . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Notch filter for adjacent sound carrier suppression . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Video low pass frequency response in smooth roll off or low ripple mode . . . . . . . . . . . .30 SSIF and FM radio band-pass filters (center frequency 5.5 MHz chosen). . . . . . . . . . .31 Video equalizer curves. . . . . . . . . . . . . . . . . . . . .36 TDA8296 SSIF characteristic versus CS (refer to Figure 23) typical values; termination 75 and 1 k in parallel . . . . . . . . . . . . . . . . . . .40 TDA8296 AFC characteristic . . . . . . . . . . . . . . . .42 Internal low IF frequency response in front of the VIF demodulator . . . . . . . . . . . . . . . . . . . .45 Example for the programmable group delay equalizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 Example for the programmable video equalizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 Typical application of TDA8296 . . . . . . . . . . . . . .64 IF input application for interlacing TDA1827x . . .64 IF input application. . . . . . . . . . . . . . . . . . . . . . . .64 Main application diagram . . . . . . . . . . . . . . . . . . .65 75 load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 High ohmic load . . . . . . . . . . . . . . . . . . . . . . . . . .66 Buffer application with 75 load . . . . . . . . . . . . .67 PCB pattern using circuit diagrams of Figure 20, Figure 22, Figure 23 and 16 MHz reference from XTAL . . . . . . . . . . . . . . . . . . . . . .67 PCB pattern using circuit diagrams of Figure 20, Figure 22, Figure 23 and 16 MHz reference from master . . . . . . . . . . .68 TDA8296 calculated DAC characteristic . . . . . . .69 Internal CVBS signal in front of video DAC (typical characteristic) . . . . . . . . . . . . . . . . . . . . .70 Internal SSIF signal in front of sound DAC (typical characteristic, also dependent on SSIF_LVL[7:0] at address 23h) . . . . . . . . . . . . . .70 Hardware reset operation . . . . . . . . . . . . . . . . . .71 Reference clock application . . . . . . . . . . . . . . . . .72 Oscillator application . . . . . . . . . . . . . . . . . . . . . .72 Boundary scan block diagram . . . . . . . . . . . . . . .75 Boundary scan timing diagram . . . . . . . . . . . . . .76 Package outline SOT618-1 (HVQFN40) . . . . . . .77 Temperature profiles for large and small components . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80 TDA8296 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 3 March 2011 (c) NXP B.V. 2011. All rights reserved. 86 of 87 TDA8296 NXP Semiconductors Digital global standard low IF demodulator for analog TV and FM radio 23. Contents 1 2 3 4 5 6 7 7.1 7.2 8 8.1 8.2 8.3 8.4 8.5 8.6 8.7 8.8 8.9 9 9.1 9.1.1 9.1.2 9.2 9.3 9.3.1 9.3.2 9.3.3 9.3.4 9.3.5 9.3.6 9.3.7 9.3.8 9.3.9 9.3.10 9.3.11 9.3.12 9.3.13 9.3.14 9.3.15 9.3.16 9.3.17 9.3.18 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Quick reference data . . . . . . . . . . . . . . . . . . . . . 3 Ordering information . . . . . . . . . . . . . . . . . . . . . 5 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 6 Pinning information . . . . . . . . . . . . . . . . . . . . . . 7 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 8 Functional description . . . . . . . . . . . . . . . . . . 10 IF ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 PLL demodulator . . . . . . . . . . . . . . . . . . . . . . 10 Nyquist filter, video low-pass filter, video and group delay equalizer, video leveling. . . . 10 Upsampler and video DAC . . . . . . . . . . . . . . . 11 SSIF/mono sound processing . . . . . . . . . . . . 11 Tuner IF AGC . . . . . . . . . . . . . . . . . . . . . . . . . 11 Digital IF AGC. . . . . . . . . . . . . . . . . . . . . . . . . 12 Clock generation. . . . . . . . . . . . . . . . . . . . . . . 12 2 I C-bus control . . . . . . . . . . . . . . . . . . . . . . . . . 12 Protocol of the I2C-bus serial interface . . . . . . 12 Write mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Read mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Register overview . . . . . . . . . . . . . . . . . . . . . . 15 Register description . . . . . . . . . . . . . . . . . . . . 23 Standard setting with easy programming . . . . 23 Diverse functions (includes tuner IF AGC Pin mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 ADC headroom . . . . . . . . . . . . . . . . . . . . . . . . 25 Picture carrier PLL functions . . . . . . . . . . . . . 26 Picture and sound carrier DTO . . . . . . . . . . . . 26 Filter settings . . . . . . . . . . . . . . . . . . . . . . . . . 28 Group delay equalization . . . . . . . . . . . . . . . . 31 Digital IF AGC functions . . . . . . . . . . . . . . . . . 32 Tuner IF AGC functions . . . . . . . . . . . . . . . . . 32 V-sync adjustment . . . . . . . . . . . . . . . . . . . . . 34 CVBS settings . . . . . . . . . . . . . . . . . . . . . . . . 34 SSIF and mono sound settings . . . . . . . . . . . 36 Status registers: ADC saturation, AFC, H/V PLL and AGC . . . . . . . . . . . . . . . . . . . . . 40 Chip identification and Standby mode . . . . . . 43 ADC control . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Video and sound DAC control . . . . . . . . . . . . 45 Clock generation (PLL and crystal oscillator) . 46 GPIOs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 9.3.19 Special equalizer functions for group delay and video (CVBS). . . . . . . . . . . . . . . . . 10 Limiting values . . . . . . . . . . . . . . . . . . . . . . . . 11 Thermal characteristics . . . . . . . . . . . . . . . . . 12 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 13 Application information . . . . . . . . . . . . . . . . . 13.1 Typical application . . . . . . . . . . . . . . . . . . . . . 13.1.1 IF input application. . . . . . . . . . . . . . . . . . . . . 13.2 Detailed application diagrams . . . . . . . . . . . . 13.2.1 Main application diagram . . . . . . . . . . . . . . . . 13.2.2 75 W application . . . . . . . . . . . . . . . . . . . . . . 13.2.3 100 W application . . . . . . . . . . . . . . . . . . . . . 13.2.4 Buffer application . . . . . . . . . . . . . . . . . . . . . . 13.2.5 Layout recommendations. . . . . . . . . . . . . . . . 13.3 DAC connection . . . . . . . . . . . . . . . . . . . . . . . 13.4 ADC connection . . . . . . . . . . . . . . . . . . . . . . . 13.5 Reset operation . . . . . . . . . . . . . . . . . . . . . . . 13.5.1 Hardware reset . . . . . . . . . . . . . . . . . . . . . . . 13.5.2 Software reset . . . . . . . . . . . . . . . . . . . . . . . . 13.6 Application hints . . . . . . . . . . . . . . . . . . . . . . . 13.7 Crystal connection . . . . . . . . . . . . . . . . . . . . . 13.8 Alternative ADC sampling rates . . . . . . . . . . . 14 Test information . . . . . . . . . . . . . . . . . . . . . . . 14.1 Boundary scan interface ("IEEE Std. 1149.1") . . . . . . . . . . . . . . . . . . . . 15 Package outline. . . . . . . . . . . . . . . . . . . . . . . . 16 Soldering of SMD packages . . . . . . . . . . . . . . 16.1 Introduction to soldering. . . . . . . . . . . . . . . . . 16.2 Wave and reflow soldering. . . . . . . . . . . . . . . 16.3 Wave soldering . . . . . . . . . . . . . . . . . . . . . . . 16.4 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . 17 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . 18 Revision history . . . . . . . . . . . . . . . . . . . . . . . 19 Legal information . . . . . . . . . . . . . . . . . . . . . . 19.1 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 19.2 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.3 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . 19.4 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Contact information . . . . . . . . . . . . . . . . . . . . 21 Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 53 53 54 64 64 64 65 65 66 66 67 67 68 71 71 71 71 71 72 73 74 74 77 78 78 78 78 79 80 81 82 82 82 82 83 83 84 86 87 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section `Legal information'. (c) NXP B.V. 2011. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 3 March 2011 Document identifier: TDA8296