Ordering information AC-DC Power Supplies Open Frame/ Enclosed Type LGA50A LG 1 A 50 2 3 A 4 Recommended EMI/EMC Filter NAC-06-472 R LGA LGA High voltage pulse noise type : NAP series Low leakage current type : NAM series *The EMI/EMC Filter is recommended *to connect with several devices. -5 5 -O 6 1Series name 2Single output 3Output wattage 4100/120V input 5Output voltage 6Optional C :with Coating G :Low leakage current H :with the function to be acceptable to output peak current (only 24V) J1:VH(J.S.T.)connector type S :with Chassis SN:with Chassis & cover Y :with Potentiometer This power supply is manufactured by SMD technology.The stress to P.C.B like twisting or bending causes the defect of the unit,so handle the unit with care. MODEL MAX OUTPUT WATTAGE[W] DC OUTPUT LGA50A-3R3-Y LGA50A-5 33 50 3.3V 10A 5V 10A LGA50A-12 51.6 12V 4.3A LGA50A-15 52.5 15V 3.5A LGA50A-24 60 24V 2.5A LGA50A-24-H LGA50A-48 60 62.4 24V 2.5 (Peak 3.2) A 48V 1.3A SPECIFICATIONS INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V FREQUENCY[Hz] EFFICIENCY[%] ACIN 100V INRUSH CURRENT[A] ACIN 100V LEAKAGE CURRENT[mA] VOLTAGE[V] *3 CURRENT[A] LINE REGULATION[mV] LOAD REGULATION[mV] 1 0 to +50C * *4 RIPPLE[mVp-p] -10 - 0C *1 1 0 to +50C * *4 RIPPLE NOISE[mVp-p] -10 - 0C *1 0 to +50C*4 TEMPERATURE REGULATION[mV] -10 to +50C*4 *2 DRIFT[mV] START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION OPERATING INDICATION REMOTE SENSING REMOTE ON/OFF INPUT-OUTPUT INPUT-FG OUTPUT-FG OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS CONDUCTED NOISE CASE SIZE/WEIGHT COOLING METHOD LGA50A-3R3-Y LGA50A-5 LGA50A-12 LGA50A-24 LGA50A-24-H LGA50A-48 LGA50A-15 AC85 - 132 1f (Refer to Instruction Manual 1.1, and 3.2 Derating) 0.8typ (Io=100%) 1.3typ (Io=100%) 47 - 440 (Refer to Instruction Manual 1.1) 74.0typ (Io=100%) 79.0typ (Io=100%) 82.0typ (Io=100%) 83.0typ (Io=100%) 85.0typ (Io=100%) 85.0typ (Io=100%) 85.0typ (Io=100%) 30typ (Io=100%), (At cold start), (Ta= 25C) 0.5max (ACIN 100V, 60Hz, Io=100%, According to IEC60950-1 and DEN-AN) 3.3 12 24 24 5 15 48 10.0 4.3 2.5 2.5 (Peak 3.2) 1.3 10.0 3.5 20max 48max 96max 96max 20max 60max 192max 40max 100max 150max 150max 40max 120max 300max 80max 120max 150max 80max 120max 120max 240max 140max 160max 160max 320max 140max 160max 200max 120max 150max 150max 300max 120max 150max 350max 160max 180max 400max 160max 180max 180max 360max 50max 150max 480max 50max 120max 240max 240max 60max 150max 290max 290max 60max 180max 600max 20max 48max 96max 96max 20max 60max 192max 200max (ACIN 100V, Io=100%) 20typ (ACIN 100V, Io=100%) Fixed ("Y"which can be adjusted the output is available as optional t 10%) 2.85 - 3.63 4.90 - 5.30 14.40 - 15.60 46.00 - 50.00 3.30 - 3.40 11.50 - 12.50 23.00 - 25.00 23.00 - 25.00 Works over 105% of rating (works over 101% of peak current at option -H) and recovers automatically 13.80 - 16.80 17.30 - 21.00 27.60 - 35.00 27.60 - 35.00 55.20 - 67.20 5.75 - 7.00 4.00 - 5.25 Not provided Not provided Not provided AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC500V 1minute, Cutoff current = 25mA, DC500V 50MW min (At Room Temperature) -10 to +60C, 20 - 90%RH (Non condensing) (Refer to Instruction Manual 3.2), 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL (CSA60950-1), EN60950-1 Complies with DEN-AN Complies with FCC-B, VCCI-B, CISPR-B, EN55011-B, EN55022-B 50X28.5X132mm [1.97X1.12X5.2 inches] (W XHXD) / 160g max (with chassis & cover : 320g max) Convection (Refer to Instruction Manual 3.2) *1 This is the value that measured on measuring board with capacitor of 22mF at 150mm from output terminal. Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM-103). *2 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant at the rated input/output. *3 Peak loading for 10sec.And Duty 35% max.or less is acceptable if the total wattage is less than the rated wattage (24V:60W). Refer to instruction Manual 5. In detail. *4 * * * * Only output 24V and 48V DC models are applied that the upper temperature limit is 45C. Avoid prolonged use under over - load. Parallel operation with other model is not possible. Derating is required when operated with chassis and cover. A sound may occur from power supply at pulse loading. LGA-2 LGA_E.indd 2 15.6.18 5:14:09 PM LGA50A Block diagram FUSE 250V 3.15A NOISE FILTER AC IN85-132V RECTIFIER INRUSH CURRENT LIMIT LGA LGA FG TRANSFORMER RECTIFIER AND FILTER INVERTER DC OUT OVER VOLTAGE PROTECTION CONTROL CONTROL External view Chassis and cover type CN2 1 1 4 Output(-) Output(+) Mounting Hole 162 [0.16] [6.38] [5.91] 6 [0.24] 15 10 [0.91] 2-M3 Mounting Hole PCB t=1.6 [0.22] [0.06] This power supply is manufactured by SMD technology. The stress to P.C.B like twisting or bending causes the defect of the unit,so handle the unit with care. Take care for SMD parts on the back to come in contact because of the vibration and not to break down. <PIN CONNECTION> Use the spacer of 8mm length or more. 4 Mounting holes are existing. CN1 CN2 I/O Connector [1.42] [0.14] 36 [5.2] 150 0.5 [0.59] [0.39] f3.5 3.5 132 Surface mount device [2.36] 30 3 CN1 4 4 5 [1.18] FG Input(N) Input(L) 3.5 20 [0.79] [0.79] [0.39] 10 40 0.5 [1.57] [0.73] 1 4-M3 Mounting Hole [0.14] [4.8] [0.2] 23 +1 -1.6 18.5 Point B 122 0.5 5 5.5max CN2 Output(-) Output(+) [0.24] [0.14] 20 0.5 CN1 FG Input(N) Input(L) 3.5 3 1 [0.28] 6 [5.91] 2-f3.5 [0.14] [1.57] 40 0.5 5 5 [0.2] 50 [1.97] Name plate Point A 150 0.5 3-f3.5 [0.14] Mounting Hole 7 [0.14] Voltage adjust (Option) 60 Standard type Mating connector CN1 1-1123724-3 1-1123722-5 CN2 1-1123723-4 1-1123722-4 Chain Loose Chain Loose Terminal 1123721-1 1318912-1 1123721-1 1318912-1 (Mfr:Tyco Electronics AMP) I/O Connector is Mfr Tyco Electronics AMP Option:-J1:VH(J.S.T) connector type. Refer to instruction Manual 5. Pin No. 1 2 3 4 5 Input AC(L) Mounting torque:0.6N.m(6.3kgf.cm)max Pin No. Output 1, 2 -V 3, 4 +V AC(N) FG Keep drawing current per pin below 5A for CN2. Tolerance : 1 [0.04] Weight : 160g max (with chassis & cover : 320g max) PCB material / thickness : CEM3 / 1.6mm [0.06] Optional chassis and cover material : Electric galvanizing steel board. Dimensions in mm, [ ]=inches LGA-3 LGA-3 LGA_E.indd 3 15.6.18 5:14:09 PM Ordering information AC-DC Power Supplies Open Frame/ Enclosed Type LGA75A LG 1 A 75 2 3 A 4 Recommended EMI/EMC Filter NAC-06-472 R LGA LGA High voltage pulse noise type : NAP series Low leakage current type : NAM series *The EMI/EMC Filter is recommended *to connect with several devices. -5 5 -O 6 1Series name 2Single output 3Output wattage 4100/120V input 5Output voltage 6Optional C :with Coating G :Low leakage current H :with the function to be acceptable to output peak current (only 24V) J1:VH(J.S.T.)connector type S :with Chassis SN:with Chassis & cover Y :with Potentiometer This power supply is manufactured by SMD technology.The stress to P.C.B like twisting or bending causes the defect of the unit,so handle the unit with care. MODEL MAX OUTPUT WATTAGE[W] DC OUTPUT LGA75A-3R3-Y LGA75A-5 49.5 75 3.3V 15A 5V 15A LGA75A-12 75.6 12V 6.3A LGA75A-15 75 15V 5A LGA75A-24 76.8 24V 3.2A LGA75A-24-H LGA75A-48 76.8 76.8 24V 3.2 (Peak 4.2) A 48V 1.6A SPECIFICATIONS INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V FREQUENCY[Hz] EFFICIENCY[%] ACIN 100V INRUSH CURRENT[A] ACIN 100V LEAKAGE CURRENT[mA] VOLTAGE[V] *3 CURRENT[A] LINE REGULATION[mV] LOAD REGULATION[mV] 0 to +50C *1 RIPPLE[mVp-p] -10 - 0C *1 0 to +50C *1 RIPPLE NOISE[mVp-p] -10 - 0C *1 0 to +50C TEMPERATURE REGULATION[mV] -10 to +50C *2 DRIFT[mV] START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION OPERATING INDICATION REMOTE SENSING REMOTE ON/OFF INPUT-OUTPUT INPUT-FG OUTPUT-FG OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS CONDUCTED NOISE CASE SIZE/WEIGHT COOLING METHOD LGA75A-3R3-Y LGA75A-5 LGA75A-12 LGA75A-24 LGA75A-24-H LGA75A-48 LGA75A-15 AC85 - 132 1f (Refer to Instruction Manual 1.1, and 3.2 Derating) 1.3typ (Io=100%) 1.7typ (Io=100%) 47 - 440 (Refer to Instruction Manual 1.1) 75.0typ (Io=100%) 79.0typ (Io=100%) 83.0typ (Io=100%) 84.0typ (Io=100%) 86.0typ (Io=100%) 86.0typ (Io=100%) 86.0typ (Io=100%) 30typ (Io=100%), (At cold start), (Ta= 25C) 0.5max (ACIN 100V, 60Hz, Io=100%, According to IEC60950-1 and DEN-AN) 3.3 12 24 24 5 15 48 15.0 6.3 3.2 3.2 (Peak 4.2) 1.6 15.0 5.0 20max 48max 96max 96max 20max 60max 192max 40max 100max 150max 150max 40max 120max 300max 80max 120max 150max 80max 120max 120max 240max 140max 160max 160max 320max 140max 160max 200max 120max 150max 150max 300max 120max 150max 350max 160max 180max 400max 160max 180max 180max 360max 50max 150max 480max 50max 120max 240max 240max 60max 150max 290max 290max 60max 180max 600max 20max 48max 96max 96max 20max 60max 192max 200max (ACIN 100V, Io=100%) 20typ (ACIN 100V, Io=100%) 2.85 - 3.63 Fixed ("Y"which can be adjusted the output is available as optional t 10%) 4.90 - 5.30 14.40 - 15.60 46.00 - 50.00 3.30 - 3.40 11.50 - 12.50 23.00 - 25.00 23.00 - 25.00 Works over 105% of rating (works over 101% of peak current at option -H) and recovers automatically 5.75 - 7.00 13.80 - 16.80 17.30 - 21.00 27.60 - 35.00 27.60 - 35.00 55.20 - 67.20 4.00 - 5.25 Not provided Not provided Not provided AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC500V 1minute, Cutoff current = 25mA, DC500V 50MW min (At Room Temperature) -10 to +60C, 20 - 90%RH (Non condensing) (Refer to Instruction Manual 3.2), 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL (CSA60950-1), EN60950-1 Complies with DEN-AN Complies with FCC-B, VCCI-B, CISPR-B, EN55011-B, EN55022-B 50X34.5X150mm [1.97X1.36X5.91 inches] (WXHXD) / 200g max (with chassis & cover : 410g max) Convection (Refer to Instruction Manual 3.2) *1 This is the value that measured on measuring board with capacitor of 22mF at 150mm from output terminal. Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM-103). *2 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant at the rated input/output. *3 Peak loading for 10sec.And Duty 35% max.or less is acceptable if the total wattage is less than the rated wattage. Refer to instruction Manual 5. In detail. * Avoid prolonged use under over - load. * Parallel operation with other model is not possible. * Derating is required when operated with chassis and cover. * A sound may occur from power supply at pulse loading. LGA-4 LGA_E.indd 4 15.6.18 5:14:11 PM LGA75A Block diagram FUSE 250V 5A NOISE FILTER AC IN85-132V RECTIFIER INRUSH CURRENT LIMIT LGA LGA FG TRANSFORMER RECTIFIER AND FILTER INVERTER DC OUT OVER VOLTAGE PROTECTION CONTROL CONTROL External view Chassis and cover type CN1 6 Output(+) 60 Output(-) 180 [0.22] 4.5 15 15 5.5 [6.65] [0.59] [0.59] 169 0.5 [0.18] [1.14] f4.5 2-M4 Mounting Hole PCB t=1.6 Surface mount device [0.22] [0.06] This power supply is manufactured by SMD technology. The stress to P.C.B like twisting or bending causes the defect of the unit,so handle the unit with care. Take care for SMD parts on the back to come in contact because of the vibration and not to break down. <PIN CONNECTION> Use the spacer of 8mm length or more. 4 Mounting holes are existing. CN1 CN2 I/O Connector 1 [2.36] 4.5 3 1 [0.18] 20 [0.79] [0.79] 10 [0.39] [0.61] 15.5 150 29 +1 -1.6 CN2 5 [7.09] [5.91] 5.5max FG Input(N) Input(L) Mounting Hole [5.51] [0.2] 4-M4 Mounting Hole [1.18] 4 [0.16] [0.22] [1.77] Point B 140 0.5 5.5 [6.65] [0.18] 5 Output(+) 169 0.5 30 6 Output(-) 40 0.5 1 [0.18] [1.57] CN1 CN2 FG Input(N) Input(L) 2-f4.5 20 0.5 3 1 3-f3.5 [0.14] Mounting Hole 3.5 [1.57] 5 13.5 [0.53] [0.2] 50 [1.97] 5 40 0.5 Name plate Point A [0.14] Voltage adjust (Option) 45 Standard type Mating connector CN1 1-1123724-3 1-1123722-5 CN2 1-1123723-6 1-1123722-6 Chain Loose Chain Loose Terminal 1123721-1 1318912-1 1123721-1 1318912-1 (Mfr:Tyco Electronics AMP) I/O Connector is Mfr Tyco Electronics AMP Option:-J1:VH(J.S.T) connector type. Refer to instruction Manual 5. Pin No. 1 2 3 4 5 Input AC(L) Mounting torque:1.5N*m(16kgf*cm)max Pin No. Output 1 to 3 -V 4 to 6 +V AC(N) FG Keep drawing current per pin below 5A for CN2. Tolerance : 1 [0.04] Weight : 200g max (with chassis & cover : 410g max) PCB material / thickness : CEM3 / 1.6mm [0.06] Optional chassis and cover material : Electric galvanizing steel board. Dimensions in mm, [ ]=inches LGA-5 LGA-5 LGA_E.indd 5 15.6.18 5:14:12 PM Ordering information AC-DC Power Supplies Open Frame/ Enclosed Type LGA100A LG 1 A 100 2 3 A 4 Recommended EMI/EMC Filter NAC-06-472 R LGA LGA High voltage pulse noise type : NAP series Low leakage current type : NAM series *The EMI/EMC Filter is recommended *to connect with several devices. -5 5 -O 6 1Series name 2Single output 3Output wattage 4100/120V input 5Output voltage 6Optional C :with Coating G :Low leakage current H :with the function to be acceptable to output peak current (only 24V) J1:VH(J.S.T.)connector type S :with Chassis SN:with Chassis & cover Y :with Potentiometer This power supply is manufactured by SMD technology.The stress to P.C.B like twisting or bending causes the defect of the unit,so handle the unit with care. MODEL MAX OUTPUT WATTAGE[W] DC OUTPUT LGA100A-3R3-Y 66 3.3V 20A LGA100A-5-Y LGA100A-12 102 100 12V 8.5A 5V 20A LGA100A-15 105 15V 7A LGA100A-24 103.2 24V 4.3A LGA100A-24-H LGA100A-48 103.2 100.8 24V 4.3 (Peak 5.4) A 48V 2.1A SPECIFICATIONS INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V FREQUENCY[Hz] EFFICIENCY[%] ACIN 100V INRUSH CURRENT[A] ACIN 100V LEAKAGE CURRENT[mA] VOLTAGE[V] *3 CURRENT[A] LINE REGULATION[mV] LOAD REGULATION[mV] 0 to +50C *1 RIPPLE[mVp-p] -10 - 0C *1 0 to +50C *1 RIPPLE NOISE[mVp-p] -10 - 0C *1 0 to +50C TEMPERATURE REGULATION[mV] -10 to +50C *2 DRIFT[mV] START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION OPERATING INDICATION REMOTE SENSING REMOTE ON/OFF INPUT-OUTPUT INPUT-FG OUTPUT-FG OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS CONDUCTED NOISE CASE SIZE/WEIGHT COOLING METHOD LGA100A-3R3-Y LGA100A-5-Y LGA100A-12 LGA100A-24 LGA100A-24-H LGA100A-48 LGA100A-15 AC85 - 132 1f (Refer to Instruction Manual 1.1, and 3.2 Derating) 2.4typ (Io=100%) 1.6typ (Io=100%) 47 - 440 (Refer to Instruction Manual 1.1) 76.0typ (Io=100%) 80.0typ (Io=100%) 83.0typ (Io=100%) 84.0typ (Io=100%) 85.5typ (Io=100%) 85.5typ (Io=100%) 85.5typ (Io=100%) 15typ (Io=100%, More than 10sec. to re-start) 0.5max (ACIN 100V, 60Hz, Io=100%, According to IEC60950-1 and DEN-AN) 3.3 12 24 24 5 15 48 20.0 8.5 4.3 4.3 (Peak 5.4) 2.1 20.0 7.0 20max 48max 96max 96max 20max 60max 192max 40max 100max 150max 150max 40max 120max 300max 80max 120max 150max 80max 120max 120max 240max 140max 160max 160max 320max 140max 160max 200max 120max 150max 150max 300max 120max 150max 350max 160max 180max 400max 160max 180max 180max 360max 50max 150max 480max 50max 120max 240max 240max 60max 150max 290max 290max 60max 180max 600max 20max 48max 96max 96max 20max 60max 192max 200max (ACIN 100V, Io=100%) 20typ (ACIN 100V, Io=100%) 4.50 - 5.50 2.85 - 3.63 Fixed ("Y"which can be adjusted the output is available as optional t 10%) 5.00 - 5.15 14.40 - 15.60 46.00 - 50.00 3.30 - 3.40 11.50 - 12.50 23.00 - 25.00 23.00 - 25.00 Works over 105% of rating (works over 101% of peak current at option -H) and recovers automatically 5.75 - 7.00 13.80 - 16.80 17.30 - 21.00 27.60 - 35.00 27.60 - 35.00 55.20 - 67.20 4.00 - 5.25 Not provided Not provided Not provided AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC500V 1minute, Cutoff current = 25mA, DC500V 50MW min (At Room Temperature) -10 to +60C, 20 - 90%RH (Non condensing) (Refer to Instruction Manual 3.2), 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL (CSA60950-1), EN60950-1 Complies with DEN-AN Complies with FCC-B, VCCI-B, CISPR-B, EN55011-B, EN55022-B 62X35.5X155mm [2.44X1.4X6.1 inches] (WXHXD) / 300g max (with chassis & cover : 530g max) Convection (Refer to Instruction Manual 3.2) *1 This is the value that measured on measuring board with capacitor of 22mF at 150mm from output terminal. Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM-103). *2 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant at the rated input/output. *3 Peak loading for 10sec.And Duty 35% max.or less is acceptable if the total wattage is less than the rated wattage. Refer to instruction Manual 5. In detail. * Avoid prolonged use under over - load. * Parallel operation with other model is not possible. * Derating is required when operated with chassis and cover. * A sound may occur from power supply at pulse loading. LGA-6 LGA_E.indd 6 15.6.18 5:14:13 PM LGA100A Block diagram FUSE 250V 5A NOISE FILTER AC IN85-132V RECTIFIER INRUSH CURRENT LIMIT LGA LGA FG TRANSFORMER RECTIFIER AND FILTER INVERTER DC OUT OVER VOLTAGE PROTECTION CONTROL CONTROL External view Output(+) CN2 5 3 1 Output(-) 1 CN1 8 Output(+) Mounting Hole [7.28] [5.71] [0.2] 155 f4.5 173 0.5 [0.18] [6.81] 6 [0.24] 4.5 [1.18] 2-M4 Mounting Hole 20 30 +1 -1.6 [6.1] PCB t=1.6 Surface mount device [0.06] [0.22] 5.5max 185 [0.65] 145 0.5 [1.77] 5 15 16.5 [0.18] 4 [0.16] 3.5 Voltage adjust (LGA100A-5-Y or Optional) [0.14] 5 [0.2] 4.5 8 [2.83] 23 [0.91] FG Input(N) Input(L) 36 72 [1.42] Output(-) 45 1 4-M4 Mounting Hole [0.79] [0.59] CN1 CN2 FG Input(N) Input(L) [0.24] [6.81] [0.18] [0.98] 13 3 1 45 0.5 52 0.5 [2.05] 62 [2.44] 5 6 173 0.5 2-f4.5 [0.51] 3-f3.5 [0.14] Mounting Hole 25 0.5 Point B [1.77] Name plate Point A Chassis and cover type [0.18] Standard type Mounting torque:1.5N*m(16kgf*cm)max This power supply is manufactured by SMD technology. The stress to P.C.B like twisting or bending causes the defect of the unit,so handle the unit with care. Take care for SMD parts on the back to come in contact because of the vibration and not to break down. <PIN CONNECTION> Use the spacer of 8mm length or more. 4 Mounting holes are existing. CN1 CN2 I/O Connector Mating connector CN1 1-1123724-3 1-1123722-5 CN2 1-1123723-8 1-1123722-8 Chain Loose Chain Loose Terminal 1123721-1 1318912-1 1123721-1 1318912-1 (Mfr:Tyco Electronics AMP) I/O Connector is Mfr Tyco Electronics AMP Option:-J1:VH(J.S.T) connector type. Refer to instruction Manual 5. Pin No. 1 2 3 4 5 Input AC(L) Pin No. Output 1 to 4 -V 5 to 8 +V AC(N) FG Keep drawing current per pin below 5A for CN2. Tolerance : 1 [0.04] Weight : 300g max (with chassis & cover : 530g max) PCB material / thickness : CEM3 / 1.6mm [0.06] Optional chassis and cover material : Electric galvanizing steel board. Dimensions in mm, [ ]=inches LGA-7 LGA-7 LGA_E.indd 7 15.6.18 5:14:14 PM Ordering information AC-DC Power Supplies Open Frame/ Enclosed Type LGA150A LG 1 A 150 2 3 A 4 Recommended EMI/EMC Filter NAC-06-472 R LGA LGA High voltage pulse noise type : NAP series Low leakage current type : NAM series *The EMI/EMC Filter is recommended *to connect with several devices. -5 5 -O 6 1Series name 2Single output 3Output wattage 4100/120V input 5Output voltage 6Optional C :with Coating G :Low leakage current H :with the function to be acceptable to output peak current (only 24V) J1:VH(J.S.T.)connector type S :with Chassis SN:with Chassis & cover Y :with Potentiometer This power supply is manufactured by SMD technology.The stress to P.C.B like twisting or bending causes the defect of the unit,so handle the unit with care. MODEL MAX OUTPUT WATTAGE[W] DC OUTPUT LGA150A-3R3-Y LGA150A-5-Y 99 150 3.3V 30A 5V 30A LGA150A-12 150 12V 12.5A LGA150A-15 150 15V 10A LGA150A-24 151.2 24V 6.3A LGA150A-24-H LGA150A-48 151.2 153.6 24V 6.3 (Peak 7.9) A 48V 3.2A SPECIFICATIONS INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V FREQUENCY[Hz] EFFICIENCY[%] ACIN 100V INRUSH CURRENT[A] ACIN 100V LEAKAGE CURRENT[mA] VOLTAGE[V] *3 CURRENT[A] LINE REGULATION[mV] LOAD REGULATION[mV] 0 to +40C *1 RIPPLE[mVp-p] -10 - 0C *1 0 to +40C *1 RIPPLE NOISE[mVp-p] -10 - 0C *1 0 to +40C TEMPERATURE REGULATION[mV] -10 to +40C *2 DRIFT[mV] START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION OPERATING INDICATION REMOTE SENSING REMOTE ON/OFF INPUT-OUTPUT INPUT-FG OUTPUT-FG OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS CONDUCTED NOISE CASE SIZE/WEIGHT COOLING METHOD LGA150A-3R3-Y LGA150A-5-Y LGA150A-12 LGA150A-24 LGA150A-24-H LGA150A-48 LGA150A-15 AC85 - 132 1f (Refer to Instruction Manual 1.1, and 3.2 Derating) 2.6typ (Io=100%) 3.6typ (Io=100%) 47 - 440 (Refer to Instruction Manual 1.1) 76.0typ (Io=100%) 82.0typ (Io=100%) 84.5typ (Io=100%) 85.5typ (Io=100%) 87.0typ (Io=100%) 87.0typ (Io=100%) 87.0typ (Io=100%) 15 /15 typ (Primary / Secondary Surge Current, Io=100%, More than 10sec. to re-start) 0.5max (ACIN 100V, 60Hz, Io=100%, According to IEC60950-1 and DEN-AN) 3.3 12 24 24 5 15 48 30.0 12.5 6.3 6.3 (Peak 7.9) 3.2 30.0 10.0 20max 48max 96max 96max 20max 60max 192max 40max 100max 150max 150max 40max 120max 300max 80max 120max 150max 80max 120max 120max 240max 140max 160max 160max 320max 140max 160max 200max 120max 150max 150max 300max 120max 150max 350max 160max 180max 400max 160max 180max 180max 360max 50max 150max 480max 50max 120max 240max 240max 60max 150max 290max 290max 60max 180max 600max 20max 48max 96max 96max 20max 60max 192max 200max (ACIN 100V, Io=100%) 20typ (ACIN 100V, Io=100%) 4.50 - 5.50 2.85 - 3.63 Fixed ("Y"which can be adjusted the output is available as optional t 10%) 5.00 - 5.15 14.40 - 15.60 46.00 - 50.00 3.30 - 3.40 11.50 - 12.50 23.00 - 25.00 23.00 - 25.00 Works over 105% of rating (works over 101% of peak current at option -H) and recovers automatically 5.75 - 7.00 13.80 - 16.80 17.30 - 21.00 27.60 - 35.00 27.60 - 35.00 55.20 - 67.20 4.00 - 5.25 Not provided Not provided Not provided AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC500V 1minute, Cutoff current = 25mA, DC500V 50M W min (At Room Temperature) -10 to +60C, 20 - 90%RH (Non condensing) (Refer to Instruction Manual 3.2), 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL (CSA60950-1), EN60950-1 Complies with DEN-AN Complies with FCC-B, VCCI-B, CISPR-B, EN55011-B, EN55022-B 75X39 X160mm [2.95X1.54X6.3 inches] (WXHXD) / 420g max (with chassis & cover : 650g max) Convection (Refer to Instruction Manual 3.2) *1 This is the value that measured on measuring board with capacitor of 22mF at 150mm from output terminal. Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM-103). *2 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant at the rated input/output. *3 Peak loading for 10sec.And Duty 35% max.or less is acceptable if the total wattage is less than the rated wattage. Refer to instruction Manual 5. In detail. * Avoid prolonged use under over - load. * Parallel operation with other model is not possible. * Derating is required when operated with chassis and cover. * A sound may occur from power supply at pulse loading. LGA-8 LGA_E.indd 8 15.6.18 5:14:15 PM LGA150A Block diagram FUSE 250V 6.3A NOISE FILTER AC IN85-132V INRUSH CURRENT LIMIT RECTIFIER LGA LGA FG TRANSFORMER RECTIFIER AND FILTER INVERTER DC OUT OVER VOLTAGE PROTECTION CONTROL CONTROL External view Chassis and cover type 7 1 CN1 [0.26] Mounting Hole [0.71] 4.5 [0.24] PCB t=1.6 [0.06] This power supply is manufactured by SMD technology. The stress to P.C.B like twisting or bending causes the defect of the unit,so handle the unit with care. Take care for SMD parts on the back to come in contact because of the vibration and not to break down. Use the spacer of 8mm length or more. 4 Mounting holes are existing. I/O Connector Mating connector CN1 1-1123724-3 1-1123722-5 CN2 1-1123723-6 CN3 1-1123723-7 Terminal Chain 1123721-1 1318912-1 Loose 1123721-1 Chain 1-1123722-6 1318912-1 Loose Chain 1123721-1 1-1123722-7 1318912-1 Loose (Mfr:Tyco Electronics AMP) I/O Connector is Mfr Tyco Electronics AMP Option:-J1:VH(J.S.T) connector type. Refer to instruction Manual 5. 2-M4 Mounting Hole 20 [1.32] Surface mount device [0.22] 6 [6.93] 47 [0.18] [6.3] 33.5 +1 -1.6 [7.4] 176 0.5 [1.85] 160 5.5max 188 f4.5 15 [5.91] [0.2] [0.79] [0.59] 150 0.5 CN2 Output(+) [0.18] 5 6.5 3.5 18 [0.14] 5 [0.2] 4 6 [0.16] CN3 Output(-) [3.35] 1 42 1 5 3 [1.65] FG Input(N) Input(L) 6 Voltage adjust (LGA150A-5-Y or Optional) 4-M4 Mounting Hole [0.98] 25 6 [0.24] 4.5 CN2 Output(+) [1.38] 7 1 CN3 Output(-) [0.59] 15 CN1 1 FG Input(N) Input(L) 35 0.5 3 1 55 0.5 65 0.5 [2.56] 75 [2.95] 5 176 0.5 [6.93] [0.18] [2.17] Name plate Point A Point B 2-f4.5 [0.18] 3-f3.5 [0.14] Mounting Hole 85 Standard type Mounting torque:1.5N*m(16kgf*cm)max <PIN CONNECTION> CN1 Pin No. 1 2 3 4 5 CN2 CN3 Input AC(L) Pin No. Output Pin No. Output AC(N) 1 to 6 +V 1 to 7 -V FG Keep drawing current per pin below 5A for CN2,CN3. Tolerance : 1 [0.04] Weight : 420g max (with chassis & cover : 650g max) PCB material / thickness : CEM3 / 1.6mm [0.06] Optional chassis and cover material : Electric galvanizing steel board. Dimensions in mm, [ ]=inches LGA-9 LGA-9 LGA_E.indd 9 15.6.18 5:14:16 PM Ordering information AC-DC Power Supplies Open Frame/ Enclosed Type LGA240A LG 1 A 2 240 3 A 4 Recommended EMI/EMC Filter NAC-16-472 R LGA LGA High voltage pulse noise type : NAP series Low leakage current type : NAM series *The EMI/EMC Filter is recommended *to connect with several devices. -5 5 -O 6 1Series name 2Single output 3Output wattage 4100/120V input 5Output voltage 6Optional C :with Coating G :Low leakage current H :with the function to be acceptable to output peak current (only 24V) J1:VH(J.S.T.)connector type S :with Chassis SN:with Chassis & cover T :Vertical terminal block Y :with Potentiometer This power supply is manufactured by SMD technology.The stress to P.C.B like twisting or bending causes the defect of the unit,so handle the unit with care. MODEL MAX OUTPUT WATTAGE[W] DC OUTPUT LGA240A-24 240 24V 10A LGA240A-24-H 240 24V 10 (Peak 12.5) A SPECIFICATIONS INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V FREQUENCY[Hz] ACIN 100V EFFICIENCY[%] INRUSH CURRENT[A] ACIN 100V LEAKAGE CURRENT[mA] VOLTAGE[V] *3 CURRENT[A] LINE REGULATION[mV] LOAD REGULATION[mV] 0 to +40C *1 RIPPLE[mVp-p] -10 - 0C *1 0 to +40C *1 RIPPLE NOISE[mVp-p] -10 - 0C *1 0 to +40C TEMPERATURE REGULATION[mV] -10 to +40C *2 DRIFT[mV] START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION OPERATING INDICATION REMOTE SENSING REMOTE ON/OFF INPUT-OUTPUT INPUT-FG OUTPUT-FG OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS CONDUCTED NOISE CASE SIZE/WEIGHT COOLING METHOD LGA240A-24 LGA240A-24-H AC85 - 132 1f (Refer to Instruction Manual 1.1, and 3.2 Derating) 5.0typ (Io=100%) 47 - 440 (Refer to Instruction Manual 1.1) 86.5typ (Io=100%) 86.5typ (Io=100%) 15 / 20 typ (Primary / Secondary Surge Current, Io=100%, More than 10sec. to re-start) 0.5max (ACIN 100V, 60Hz, Io=100%, According to IEC60950-1 and DEN-AN) 24 24 10.0 10.0 (Peak 12.5) 96max 96max 150max 150max 120max 240max 160max 320max 150max 300max 180max 360max 240max 240max 290max 290max 96max 96max 200max (ACIN 100V, Io=100%) 20typ (ACIN 100V, Io=100%) Fixed ("Y"which can be adjusted the output is available as optional t 10%) 23.00 - 25.00 23.00 - 25.00 Works over 105% of rating (works over 101% of peak current at option -H) and recovers automatically 27.60 - 35.00 27.60 - 35.00 Not provided Not provided Not provided AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC500V 1minute, Cutoff current = 25mA, DC500V 50M W min (At Room Temperature) -10 to +60C, 20 - 90%RH (Non condensing) (Refer to Instruction Manual 3.2), 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL (CSA60950-1), EN60950-1 Complies with DEN-AN Complies with FCC-B, VCCI-B, CISPR-B, EN55011-B, EN55022-B 84X48.5X180mm [3.31X1.91X7.09 inches] (W XHXD) / 590g max (with chassis & cover : 880g max) Convection (Refer to Instruction Manual 3.2) *1 This is the value that measured on measuring board with capacitor of 22mF at 150mm from output terminal. Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM-103). *2 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant at the rated input/output. *3 Peak loading for 10sec.And Duty 35% max.or less is acceptable if the total wattage is less than the rated wattage. Refer to instruction Manual 5. In detail. * Avoid prolonged use under over - load. * Parallel operation with other model is not possible. * Derating is required when operated with chassis and cover. * A sound may occur from power supply at pulse loading. LGA-10 LGA_E.indd 10 15.6.18 5:14:17 PM LGA240A Block diagram FUSE 250V 12.5A NOISE FILTER AC IN85-132V INRUSH CURRENT LIMIT RECTIFIER LGA LGA FG TRANSFORMER RECTIFIER AND FILTER INVERTER DC OUT OVER VOLTAGE PROTECTION CONTROL CONTROL External view Standard type Chassis and cover type [0.24] 3.5 4 [0.16] Mounting Hole [6.69] [0.2] 180 [3.86] Point B 170 0.5 6 [0.14] [0.2] 5 89 0.5 [3.5] [1.93] 49 7 1 98 2 1 CN1 CN2 Output(+) CN3 Output(-) 59 1 5 4 [2.32] 8 7 4.5 FG Input(N) Input(L) 6 5 4-M4 Mounting Hole [0.18] 26.5 [7.87] [1.04] [0.65] 6 200 0.5 [0.18] [1.77] 7 1 CN1 CN3 Output(-) 65 0.5 2 1 1 2-f4.5 45 0.5 FG Input(N) Input(L) 5 4 [2.91] 84 [3.31] 74 0.5 8 7 16.5 4-f3.5 [0.14] Mounting Hole 21 [0.65] [2.56] 16.5 [0.83] Voltage adjust (Option) Name plate Point A CN2 Output(+) 212 [8.35] f4.5 200 0.5 [0.18] [7.87] 6 [0.24] 15 [0.59] [1.18] 4.5 [0.18] 30 [1.69] 2-M4 Mounting Hole Surface mount device [0.22] 5.5max 43 +1 -1.6 [7.09] PCB t=1.6 [0.06] This power supply is manufactured by SMD technology. The stress to P.C.B like twisting or bending causes the defect of the unit,so handle the unit with care. Take care for SMD parts on the back to come in contact because of the vibration and not to break down. Use the spacer of 8mm length or more. 5 Mounting holes are existing. I/O Connector Mating connector CN1 7-1565036-6 1-1123722-8 CN2 1-1123723-6 1-1123722-6 CN3 1-1123723-7 1-1123722-7 Terminal Chain 1123721-1 1318912-1 Loose 1123721-1 Chain 1318912-1 Loose Chain 1123721-1 1318912-1 Loose (Mfr:Tyco Electronics AMP) I/O Connector is Mfr Tyco Electronics AMP Option:-J1:VH(J.S.T) connector type. Refer to instruction Manual 5. Mounting torque:1.5N*m(16kgf*cm)max <PIN CONNECTION> CN1 Pin No. 1, 2 3 4, 5 6 7, 8 CN2 CN3 Input AC(L) Pin No. Output Pin No. Output AC(N) 1 to 6 +V 1 to 7 -V FG Keep drawing current per pin below 5A for CN1,CN2 and CN3. Tolerance : 1 [0.04] Weight : 590g max (with chassis & cover : 880g max) PCB material / thickness : CEM3 / 1.6mm [0.06] Optional chassis and cover material : Electric galvanizing steel board. Dimensions in mm, [ ]=inches LGA-11 LGA-11 LGA_E.indd 11 15.6.18 5:14:18 PM