CENTIGRID(R) SURFACE MOUNT COMMERCIAL RELAYS SERIES S114 DPDT SERIES DESIGNATION RELAY TYPE S114 DPDT basic relay S114D DPDT relay with internal diode for coil transient suppression DPDT relay with internal diodes for coil transient suppression and polarity reversal protection S114DD INTERNAL CONSTRUCTION DESCRIPTION UNI-FRAME The Series S114 Surface Mount Centigrid(R) Relay is an ultraminiature, hermetically sealed, armature relay. The low profile height (.360") and .100" ARMATURE lead spacing make it ideal for applications where extreme packaging density UPPER STATIONARY CONTACT and/or close PC board spacing are required. The specially formed leads are MOVING CONTACT LOWER STATIONARY CONTACT pre-tinned to make the relays ideal for most types of surface mount solder CENTIGRID(R) AND TO-5 reflow processes. The basic design and internal construction are identical to the Series 114 Centigrid(R) relays, and are capable of meeting Teledyne Relays' T2R(R) requirements. The following unique construction features and manufacturing techniques provide overall high reliability and excellent resistance to ENVIRONMENTAL AND PHYSICAL SPECIFICATIONS -65C to +125C Temperature Storage (Ambient) Operating -55C to +85C environmental extremes: * All welded construction. * Unique uni-frame design providing high magnetic efficiency and mechanical Vibration (General Note 1) 30 g's to 3000 Hz Shock (General Note 1) 75 g's, 6 msec, half-sine * High force/mass ratios for resistance to shock and vibration. Acceleration 50 g's * Advanced cleaning techniques provide maximum assurance of internal Enclosure Hermetically sealed Weight 0.07 oz. (1.9g) max. Reflow Temperature 260C max. temp. 1 min. max. (c)2003 TELEDYNE RELAYS rigidity. cleanliness. * Precious metal alloy contact material with gold plating assures excellent high current and dry circuit switching capabilities. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE www.teledynerelays.com S114 Page 1 S114/1203/Q1 SERIES S114 GENERAL ELECTRICAL SPECIFICATIONS (-65C to +125C unless otherwise noted) (Notes 2 & 3) Contact Arrangement Rated Duty Contact Resistance 2 Form C (DPDT) Continuous 0.1 ohm max. before life; 0.2 ohm max. after life at 1A/28Vdc (measured 1/8" from header along lead) Contact Load Ratings (DC) (See Fig. 3 for other DC resistive voltage/current ratings) Resistive: Inductive: Lamp: Low Level: 1 Amp/28Vdc 200 mA/28Vdc (320 mH) 100 mA/28Vdc 10 to 50 A/10 to 50mV Resistive: 250 mA/115Vac, 60 and 400 Hz (Case undergrounded) 100 mA/115Vac, 60 and 400 Hz (Case grounded) Contact Load Ratings (AC) Contact Life Ratings 10,000,000 cycles (typical) at low level 1,000,000 cycles (typical) at 0.5A/28Vdc resistive 100,000 cycles min. at all other loads specified above Contact Overload Rating Contact Carry Rating Coil Operating Power Operate Time Release Time Contact Bounce Intercontact Capacitance Insulation Resistance Dielectric Strength Negative Coil Transient (Vdc) Diode P.I.V. (Vdc) 2A/28Vdc Resistive (100 cycles min.) Contact factory 450 milliwatts typical at nominal rated voltage at 25C 2.0 msec max. at nominal rated coil voltage S114 Series: 1.5 msec max. S114D, S114DD Series: 4.0 msec max. 1.5 msec max. 0.4 pf typical 10,000 megohms min. between mutually isolated terminals Atmospheric pressure: 500 Vrms/60Hz 70,000 ft.: 125 Vrms/60Hz S114D, S114DD 1.0 max S114D, S114DD 100 min. DETAILED ELECTRICAL SPECIFICATIONS (-65C to +125C unless otherwise noted) (Note 3) S114-5 S114-6 S114-9 S114-12 S114-18 S114-26 S114D-5 S114D-6 S114D-9 S114D-12 S114D-18 S114D-26 S114DD-5 S114DD-6 S114DD-9 S114DD-12 S114DD-18 S114DD-26 BASE PART NUMBERS (See Note 10 for full P/N example) Coil Resistance (Ohms 10% @25C) Coil Current (mAdc @25C) (S114DD Series only) Pick-up Voltage (Vdc, Max.) Drop-out Voltage (Vdc) 5.0 5.8 50 39 93.2 128.2 3.5 4.0 0.14 2.3 0.6 2.8 6.0 8.0 98 78 57.8 74.8 4.5 5.0 0.18 3.2 0.7 3.4 9.0 12.0 220 220 33.0 42.9 6.8 7.8 0.35 4.9 0.8 5.3 12.0 16.0 390 390 25.6 32.8 9.0 10.0 0.41 6.5 0.9 6.5 18.0 24.0 880 880 17.5 22.1 13.5 14.5 0.59 10.0 1.1 10.0 26.5 32.0 1560 1560 14.8 18.5 18.0 19.0 0.89 13.0 1.4 13.0 TYPICAL DC CONTACT RATING (RESISTIVE) (Note 2) LOAD VOLTAGE (VDC) 300 250 200 150 100 50 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 LOAD CURRENT (AMPS DC) FIGURE 1 S114 Page 2 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE www.teledynerelays.com (c)2003 TELEDYNE RELAYS S114/1203/Q1 CENTIGRID(R) AND TO-5 Nom. Max. S114, 114D S114DD (Note 4) Min. (Note 5) Max. S114, S114D S114DD Min. S114, 114D Max. Min. S114DD Max. Coil Voltage (Vdc) SERIES S114 OUTLINE DIMENSIONS AND RECOMMENDED PAD LAYOUT (Notes 7, 8 & 9) .335 MAX (8.51) TERMINAL LOCATIONS & SCHEMATIC DIAGRAMS 7 .275 MAX (6.99) 8 1 .360 MAX (9.14) 2 6 .378 +.030 -.020 TYP 9.60 +.76 -.51 ( O.017 REF (.43) ) S114 2 2 TYP 5 4 3 7 8 () 1 .031 REF (.79) .035 REF (.89) .100 4 PL (2.54) 4 MAX TYP 2 6 4 MAX TYP .045 MIN 8 PL (1.14) .100 TYP (2.54) S114D .200 (5.08) .410 MIN (10.41) .375 SQ MAX (9.53) .200 (5.08) 5 4 (+) 3 7 8 () 1 .200 (5.08) (Note 6) GENERAL NOTES 1. Relay contacts will exhibit no chatter in excess of 10 msec or transfer in excess of 1 msec. 2. "Typical" characteristics are based on available data and are best estimates. No on-going verification tests are performed. 3. Unless otherwise specified, parameters are initial values. 4. For reference only. Coil resistance not directly measurable at relay terminals due to internal series diode. 5. Measured at nominal voltage for 5 sec. max. 6. Position of leads as they emerge from relay base. 7. Leads will fit noted pad layout with no overhang. 8. Lead ends are coplanar within .008" wide tolerance zone. 9. Terminals coated with SN60 or SN63 solder per QQ-S-571. Kovar exposed at sheared end of leads. 10. CENTIGRID(R) AND TO-5 2 6 DIMENSIONS ARE SHOWN IN INCHES (MILLIMETERS) 5 4 (+) 3 S114DD SCHEMATICS ARE VIEWED FROM TERMINALS Teledyne Part Numbering System for Surface Mount Relays S 114 D - 26 SURFACE MOUNT SERIES NO. D = SUPPRESSION DIODE DD = SUPPRESSION AND POLARITY PROTECTION DIODES COIL VOLTAGE 11. Add "/R" to end of part number for RoHS compliant solder coated pins (Sn99.3/Cu0.7). (c)2003 TELEDYNE RELAYS SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE www.teledynerelays.com S114 Page 3 S114/1203/Q1 Appendix A: Spacer Pads Pad designation and bottom view dimensions Height O.150 [3.81] (REF) Dim H MAX "M4" Pad for TO-5 Dim H MAX "M4" Pad for TO-5 Dim H MAX "M4" Pad for Centigrid(R) .156 [3.96] (REF) Dim H MAX .256 [6.5] (REF) "M9" Pad for Centigrid(R) For use with the following: ER411T ER412, ER412D, ER412DD 712, 712D, 712TN, RF300, RF310, RF320 ER420, ER422D, ER420DD, 421, ER421D, ER421DD, ER422, ER422D, ER422DD, 722, 722D, RF341 ER431T, ER432T, ER432, ER432D, ER432DD 732, 732D, 732TN, RF303, RF313, RF323 .295 (7.49) .300 (7.62) .305 (7.75) .400 (10.16) .410 (10.41) RF312 .350 (8.89) ER411, ER411D, ER411DD .295 (7.49) ER431, ER431D, ER431DD .400 (10.16) RF311 .300 (7.62) RF331 .410 (10.41) 172, 172D .305 (7.75) ER114, ER114D, ER114DD, J114, J114D, J114DD .300 (7.62) ER134, ER134D, ER134DD, J134, J134D, J134DD .400 (10.16) RF100 .315 (8.00) RF103 .420 (10.67) 122C, A152 .320 (8.13) ER116C, J116C .300 (7.62) ER136C, J136C .400 (10.16) RF180 .325 (8.25) A150 .305 (7.75) Notes: 1. Spacer pad material: Polyester lm. 2. To specify an "M4" or "M9" spacer pad, refer to the mounting variants portion of the part numbering example in the applicable datasheet. 3. Dimensions are in inches (mm). 4. Unless otherwise specied, tolerance is .010 (.25). 5. Add 10 m to the contact resistance show in the datasheet. 6. Add 0.01 oz. (0.25 g) to the weight of the relay assembly shown in the datasheet. (c) 2008 Teledyne Relays Dim. H Max. SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Appendix A: Spreader Pads Pad designation and bottom view dimensions Height For use with the following: .370 [9.4] MAX SQ .100 [2.54] Dim H MAX .150 [3.81] .014 [0.36] (REF) .300 [7.62] .100 [2.54] .370 [9.4] MIN .200 [5.08] "M" Pad 5/ 6/ .390 [9.91] SQ .100 [2.54] .100 [2.54] .150 [3.81] .300 [7.62] .300 [7.62] .150 [3.81] Dim H MAX ER411T, J411T, ER412, ER412D ER412DD, J412, J412D, J412DD ER412T, J412T 712, 712D, 712TN ER431T, J431T, ER432, ER432D ER432DD, J432, J432D, J432DD ER432T, J432T 732, 732D, 732TN .370 [9.4] MAX SQ .100 [2.54] Dim H MAX .150 [3.81] .014 [0.36] (REF) .300 [7.62] .100 [2.54] .200 [5.08] .370 [9.4] MIN "M3" Pad 5/ 6/ 9/ .393 (9.99) .493 (12.52) .503 (12.78) .398 (10.11) ER411T ER412, ER412D, ER412DD J412, J412D, J412DD .441 (11.20) 732, 732D "M2" Pad 7/ 8/ .388 (9.86) ER420, J420, ER420D, J420D ER420DD, J420DD, ER421, J421 ER421D, J421D, ER421DD J422D, ER422DD, J422DD, 722 712, 712D ER421, ER421D, ER421DD 722, 732D ER431T ER432, ER432D, ER432DD .130 [3.3] Dim. H Max. ER411, ER411D, ER411DD ER411TX ER412X, ER412DX, ER412DDX ER412TX 712X, 712DX, 712TNX ER420X, ER420DX, ER420DDX ER421X, ER421DX, ER421DDX ER422X, ER422DX ER422DDX, 722X, 722DDX ER431, ER431D, ER431DD ER431TX ER432X, ER432DX, ER432DDX ER432TX 732X, 732DX, 732TNX .451 (11.46) .451 (11.46) .546 (13.87) .556 (14.12) .388 (9.86) .393 (9.99) .398 (10.11) .493 (12.52) .503 (12.78) Notes: 1. Spreader pad material: Diallyl Phthalate. 2. To specify an "M", "M2" or "M3" spreader pad, refer to the mounting variants portion of the part number example in the applicable datasheet. 3. Dimensions are in inches (mm). 4. Unless otherwise specied, tolerance is .010" (0.25). 5/. Add 25 m to the contact resistance shown in the datasheet. 6/. Add .01 oz. (0.25 g) to the weight of the relay assembly shown in the datasheet. 7/. Add 50 m to the contact resistance shown in the datasheet. 8/. Add 0.025 oz (0.71 g) to the weight of the relay assembly shown in the datasheet. 9/. M3 pad to be used only when the relay has a center pin (e.g. ER411M3-12A, 722XM3-26.) (800) 284-7007 * www.teledynerelays.com +44 (0) 1236 453124 * www.teledyne-europe.com (c) 2008 Teledyne Relays Appendix A: Ground Pin Positions O.200 [O5.08] 363 "Z" POSITION "X" POSITION "Y" POSITION "Z" O.200 [O5.08] "Y" 453 TO-5 Relays: ER411T, ER412, ER412T, ER420, ER421, ER422, ER431T, ER432, ER432T, 712, 712TN, 400H, 400K, 400V, RF300, RF303, RF341, RF312, RF310, RF313, RF320, RF323 "Y" POSITION POSITION TO-5 Relays: ER411, ER431, RF311, RF331 POSITION .100 [2.54] "W" "Z" .100 [2.54] .050 [1.27] "X" .100 [2.54] POSITION POSITION "Z" POSITION POSITION .100 [2.54] POSITION "U" POSITION (ER116C and ER136C only) Centigrid(R) Relays: RF180, ER116C, 122C, ER136C .100 [2.54] Centigrid(R) Relays: RF100, RF103, ER114, ER134, 172 Indicates ground pin position Indicates glass insulated lead position Indicates ground pin or lead position depending on relay type (c) 2008 Teledyne Relays "Y" .100 [2.54] NOTES 1. Terminal views shown 2. Dimensions are in inches (mm) 3. Tolerances: .010 (.25) unless otherwise specied 4. Ground pin positions are within .015 (0.38) dia. of true position 5. Ground pin head dia., 0.035 (0.89) ref: height 0.010 (0.25) ref. 6. Lead dia. 0.017 (0.43) nom. SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE