AD8112-EVALZ/AD8113-EVALZ/AD8114-EVALZ/
AD8115-EVALZ/ADV3205-EVALZ User Guide
UG-818
One Technology Way • P. O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
Evaluation Board for the AD8112, AD8113, AD8114/AD8115, and ADV3205
Analog Crosspoint Switches
FEATURES
Full featured evaluation board for the AD8112, AD8113,
AD8114/AD8115, and ADV3205
Uses USB Board Z with PIC18F4550 for the digital control
±5 V operation
±12 V operation for audio applications of AD8112 and AD8113
EVALUATION KIT CONTENTS
AD8112-EVALZ/AD8113-EVALZ/AD8114-EVALZ/
AD8115-EVALZ/ADV3205-EVALZ evaluation board
6-pin serial wire
Instruction guide for software download
EQUIPMENT NEEDED
Signal source or video pattern generator and signal analyzer
Power supplies (5 V/1 A and ±5 V/1 A)
PC running Windows XP only
Type A to Type B USB 2.0 connector (recommended)
BNC to BNC connector for inputs and outputs
SOFTWARE NEEDED
For the AD8112, use the ADV3224/ADV3225 control
software for the 16 × 8 switch array
For the AD8113, the AD8114/AD8115, and the ADV3205, use
the ADV3226/ADV3227 control software for the 16 × 16
switch array
GENERAL DESCRIPTION
The AD8112 is a low cost, 16 × 8 fully buffered crosspoint switch
matrix, and the AD8113 is a 16 × 16 fully buffered crosspoint
switch matrix. Both products operate on voltage supplies of ±12 V
for audio applications and of ±5 V for video applications, offering a
−3 dB signal bandwidth greater than 60 MHz and channel switch
times of less than 60 ns with 0.1% settling for use in both analog
and digital audio. Both the AD8112 and the AD8113 have gain
of +2.
The AD8114/AD8115 are high speed 16 × 16 video crosspoint
switch matrices. They offer a −3 dB signal bandwidth greater
than 200 MHz and channel switch times of less than 50 ns with
1% settling. The AD8114/AD8115 include 16 independent
output buffers that can be placed into a high impedance state
for paralleling crosspoint outputs to prevent off channels from
loading the output bus. The AD8114 has a gain of +1 while the
AD8115 has a gain of +2. They both operate on voltage supplies
of ±5 V while consuming only 70 mA of idle current. Channel
switching is performed via a serial digital control that can accom-
modate the daisy-chaining of several devices or via a parallel
control to allow updating of an individual output without
reprogramming the entire array.
The ADV3205 is a 16 × 16 fully buffered crosspoint switch matrix
that operates on ±5 V, making it ideal for video applications, and
has a gain of +2. The ADV3205 offers a −3 dB signal bandwidth
of 60 MHz and channel switch times of less than 60 ns with 0.1%
settling.
The AD8112, the AD8113, and the ADV3205 are available in a
100-lead LQFP over the commercial temperature range of 0°C to
70°C. Some applications of these analog crosspoint switches are
closed circuit television (CCTV) surveillance/DVR, analog/digital
audio routers, video routers (NTSC, PAL, S-video, SECAM),
multimedia systems, and video conferencing.
The AD8114/AD8115 are available in a 100-lead LQFP over the
extended industrial temperature range of −40°C to +85°C. Some
applications of these analog crosspoint switches are routing of high
speed signals including video (NTSC, PAL, S-video, SECAM,
YUV, RGB), compressed video, three-level digital video, data
communications, and telecommunications.
The AD8112, AD8113, AD8114/AD8115, and ADV3205 are all
pin-compatible with each other and are available in the same
100-lead LQFP, which can be evaluated on a single board.
This user guide provides all of the supporting documents and
software for the evaluation of the AD8112, AD8113, AD8114/
AD8115, and ADV3205. Complete specifications for the AD8112,
AD8113, AD8114/AD8115, and ADV3205 are available in the
AD8112, AD8113, AD8114/AD8115, and ADV3205 data sheets
available from Analog Devices, Inc., and should be consulted when
working with the evaluation board.
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS. Rev. 0 | Page 1 of 10
UG-818 AD8112-EVALZ/AD8113-EVALZ/AD8114-EVALZ/AD8115-EVALZ/ADV3205-EVALZ User Guide
TABLE OF CONTENTS
Features .............................................................................................. 1
Evaluation Kit Contents ................................................................... 1
Equipment Needed ........................................................................... 1
Software Needed ............................................................................... 1
General Description ......................................................................... 1
Revision History ............................................................................... 2
Evaluation Board Photograph and Block Diagram...................... 3
Evaluation Board Hardware ............................................................ 4
Introduction .................................................................................. 4
Power Supply ................................................................................. 4
Analog Inputs.................................................................................4
Analog Outputs .............................................................................4
USB Board Z ..................................................................................4
Quick Start Guide ..........................................................................4
Evaluation Board Control Software ................................................6
Installing the Evaluation Software ..............................................6
Evaluation Board Schematic and Artwork .....................................7
Ordering Information .......................................................................9
Bill of Materials ..............................................................................9
REVISION HISTORY
3/15—Revision 0: Initial Version
Rev. 0 | Page 2 of 10
AD8112-EVALZ/AD8113-EVALZ/AD8114-EVALZ/AD8115-EVALZ/ADV3205-EVALZ User Guide UG-818
Rev. 0 | Page 3 of 10
EVALUATION BOARD PHOTOGRAPH AND BLOCK DIAGRAM
12999-001
80-BIT SHIFT REGI ST ER
WITH 5-BIT
PARAL L E L L OADI NG
DECODE
16 × 5:16 DEC O DE RS
DATA O UT
16 OUT P UTS
16 INPUTS
A0
A1
A2
A3
D4D3
80
PARAL LEL LAT CH
80 16
256
D2D1D0
RESET
CE
SER/PAR
AD8114/AD8115
UPDATE
DATA IN
CLK
SWITCH
MATRIX
ENABLE/DISABLE
OUTPUT
BUFFER
G = +1,
G = +2
SET I N DIVIDUAL
OR RE SET AL L
OUTPUTS TO
OFF
Figure 1.
UG-818 AD8112-EVALZ/AD8113-EVALZ/AD8114-EVALZ/AD8115-EVALZ/ADV3205-EVALZ User Guide
EVALUATION BOARD HARDWARE
INTRODUCTION
The AD8112-E VA L Z /AD8113-EVA L Z /AD8114-E VA LZ /
AD8115-E VA L Z /ADV3205-E VA L Z evaluation board allow
the user to easily evaluate the AD8112, the AD8113, the
AD8114/AD8115, and the ADV3205 in their various modes
and configurations. Figure 2 shows the typical bench setup
used to evaluate the five analog crosspoint switches.
POWER SUPPLY
The AD8112-E VA LZ /AD8113-E VA L Z /AD8114-EVA LZ /
AD8115-E VA L Z /ADV3205-E VA L Z evaluation board requires a
typical ±5 V power supply for the analog circuitry and a +5 V
single supply for the digital circuitry. When using the AD8112
and the AD8113 in audio applications, use +12 V in AVCC and
−12 V in AVEE. Connect the supplies as shown in Figure 2.
ANALOG INPUTS
Drive any or all of the inputs, INPUT00 to INPUT15, with a
waveform generator, video pattern generator, or any signal source
that can provide an input voltage of ±1.5 V for both the AD8112
and the AD8113 in video application and ±5 V for both the
AD8112 and the AD8113 in audio application. For the AD8114/
AD8115, the input voltage range is between ±3.5 V. The ADV3205
has an input voltage range of ±1.5 V. All inputs are terminated with
75 Ω termination resistors.
For audio applications of the AD8112 and the AD8113, input
terminations can be removed and changed because audio signals
are not as demanding on termination as video signals.
ANALOG OUTPUTS
The 16 outputs, terminated with 75 Ω termination resistors of
the AD8112-E VA L Z /AD8113-E VA L Z /AD8114-EVA L Z /
AD8115-E VA L Z /ADV3205-E VA L Z evaluation board can be
disabled using the Reset button. The waveform signal from
each or from all of the outputs is checked using a signal
analyzer such as an oscilloscope or display/monitor.
For audio applications of the AD8112 and the AD8113, output
series terminations can be shorted or changed in value because
audio signals are not as demanding on termination as video signals.
USB BOARD Z
The USB Board Z uses a PIC18F4550 microcontroller to control
the inputs and outputs of the crosspoint switch. The USB Board Z
has a USB port that easily connects the USB Board Z to the PC to
access the evaluation board control software. A 6-pin serial wire
connects the USB board Z to the AD8112-E VA L Z /AD8113-
E VA L Z /AD8114-EVA L Z /AD8115-E VA L Z /ADV3205-E VA L Z
evaluation board.
QUICK START GUIDE
Take the following steps to test the functionality and performance
of the evaluation board:
1. Remove the AD8112-E VA L Z /AD8113-EVA L Z /
AD8114-E VA L Z /AD8115-EVA L Z /ADV3205-E VA L Z
evaluation board from its packaging.
2. Connect the external bench top power supply to P1 of the
AD8112-E VA L Z /AD8113-EVA L Z /AD8114-EVA L Z /
AD8115-E VA L Z /ADV3205-E VA L Z evaluation board (or
optionally from test points AVCC to DVCC). The power
supply voltage for video applications is ±5 V, and it is ±12 V
for audio applications (applicable for the AD8112-EVA L Z /
AD8113-E VA L Z only).
3. Connect the serial wire between P2 of the AD8112-E VA L Z /
AD8113-E VA L Z /AD8114-EVA L Z /AD8115-EVA L Z /
ADV3205-E VA LZ evaluation board and P1 of the USB
Board Z.
4. Connect the Type A to Type B USB connector between the
USB Board Z and the PC control. When completed, CR1
and CR2 of the USB Board Z light alternatingly, and CR3
lights steadily.
5. Connect an input signal that is within the input voltage
range of the device through the BNC to BNC connector
between the signal generator or the video pattern generator
and IN00.
6. Connect an oscilloscope or display/monitor to OUTPUT00
through the BNC to BNC connector.
7. Open the evaluation board control software (see the
Installing the Evaluation Software section for details on
downloading the software) and then click 0 on the first row,
first column to enable INPUT00 and to enable OUTPUT00.
Rev. 0 | Page 4 of 10
AD8112-EVALZ/AD8113-EVALZ/AD8114-EVALZ/AD8115-EVALZ/ADV3205-EVALZ User Guide UG-818
Rev. 0 | Page 5 of 10
12999-002
DC POWER SUPPLY WAVEFORM/SIGNAL G ENERATOR
OSCILLOSCOPE
DISPLAY
VIDEO PATTERN GENERATORPC CO NTRO L
USB BOARD Z
ANALOG
INPUTS
ANALOG INPUTS
ANALOG
OUTPUTS
TYPE A TO
TYPE B USB
Figure 2. Typical Evaluation Setup
UG-818 AD8112-EVALZ/AD8113-EVALZ/AD8114-EVALZ/AD8115-EVALZ/ADV3205-EVALZ User Guide
Rev. 0 | Page 6 of 10
EVALUATION BOARD CONTROL SOFTWARE
This evaluation board is configured with a USB friendly interface
to allow programmability of the AD8112, the AD8113, the
AD8114/AD8115, and the ADV3205 registers.
Parallel and serial programming, using the P1 and P3 connectors
on the evaluation board, can also be done; however, these are not
focused on in this user guide. For more information on these two
programming modes, see the AD8112, the AD8113, the AD8114/
AD8115, and the ADV3205 data sheets.
The AD8112-EVALZ evaluation board uses the same evaluation
software as the ADV3224-EVALZ/ADV3225-EVALZ evaluation
board and the AD8113-EVALZ/AD8114-EVALZ/AD8115-EVALZ/
ADV3205-EVALZ evaluation board are compatible with the
evaluation software of the ADV3226-EVALZ/ADV3227-EVALZ
evaluation board.
INSTALLING THE EVALUATION SOFTWARE
The following instructions describe the procedure to install the
control software onto a Windows® PC running an XP operating
system.
Note that the software can be installed in other operating systems,
such as Windows 7 or Windows 8; however, any commands by
the user in the graphic user interface (GUI) are not read, and the
Unhandled exception has occurred in your application error
appears, as shown in Figure 3. The same error message appears
when the software is activated; however, the USB connector is
not connected to the evaluation board.
12999-003
Figure 3. ADV3226/ADV3227 Evaluation Board—Error Message
To install the software, take the following steps:
1. Download the control software at
https://ez.analog.com/docs/DOC-11329 for the AD8112
and at https://ez.analog.com/docs/DOC-11380 for the
AD8113, AD8114/AD8115, and ADV3205.
2. Extract the .zip file and open or run the .exe file. The GUI
opens, as shown in Figure 4. By default, all inputs and outputs
are disabled even though an input signal is present at the
input port of the evaluation board.
12999-004
Figure 4. GUI Window for ADV3226/ADV3227 Control Software for the
ADV3226/ADV3227 Evaluation Board
AD8112-EVALZ/AD8113-EVALZ/AD8114-EVALZ/AD8115-EVALZ/ADV3205-EVALZ User Guide UG-818
Rev. 0 | Page 7 of 10
EVALUATION BOARD SCHEMATIC AND ARTWORK
DGND
AGND
DGND
DGND
DGND
DGND
DGND
DGND
DGND
DGND
DGND
DGND
AGNDAGND AGNDAGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND AGND
AGND
AGND
AGND
DGND
AGND
AGND AGND AGND AGND AGND AGND
AGND AGNDAGND
AGND
DGND
DGND
DGND
DGND
DGND
DGND
DGND
DGND
AGND
DGND
AGND
AGNDAGND
N/C
N/C
N/C
N/C
N/C
N/C
N/C
N/C
AVEE08 /09
DVCC
IN07
AGND
AGND
AGND
AGND
AGND
AGND
AVEE
AVCC
AVEE14/15
OUT15
AVCC15
IN15
IN14
IN13
IN12
IN11
IN09
IN08
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
DGND
DVCC
IN10
OUT14
AVEE
AVCC
AGND
OUT01
OUT00
AGND
IN00
IN01
IN02
AGND
IN03
IN06
IN05
IN04
AGND
DGND
OUT12
OUT11
OUT10
OUT13
OUT09
OUT08
OUT07
OUT06
OUT05
OUT04
OUT03
OUT02
AVEE00/01
AVCC00
AVCC11/12
AVCC09/10
AVEE10 /11
AVCC13/14
AVEE12 /13
AVCC07/08
AVEE06 /07
AVCC05/06
AVEE04 /05
AVCC03/04
AVEE02 /03
N/C
ADD TRAC E TO DGND AT PIN 74 ON D UT
TIE C3 @ DUT PINS
TIE C2 @ DUT PIN S TIE C4 @ DUT PINS
R11
75Ω
75Ω
R1
R10
75Ω
75Ω
R9
R8
75Ω
75Ω
R6
R2
75Ω
75Ω
R3
R4
75Ω
75Ω
R5
R32
75Ω
75Ω
R31
R30
75Ω
75Ω
R16
75Ω
R19
75Ω
R29
50Ω
R43
R44
50Ω
R45
50Ω
R46
50Ω
R47
50Ω
R48
50Ω
C33
.01UF
AVE E AVCC
AVEE
R42
50Ω
50Ω
R41
R40
50Ω
50Ω
R39
R38
50Ω
50Ω
R37
R36
50Ω
50Ω
R35
R34
50Ω
W2
DVCC
W1
C27
.1μF
AVEE
.1μF
C2
C4
.1μF
AVCC
OUT00
IN15
OUT15
OUT14
OUT13 OU T1 2 OUT1 1 OUT1 0 OUT0 9 OUT0 8 OUT0 7 OUT0 6 OUT0 5 OUT0 4 OUT0 3 OUT0 2
OUT01
AVEE
AVCC
AVEE
AVCC
IN14
IN13
IN12
IN11
IN10
IN09
IN08 IN0 7
IN06
IN05
IN04
IN03
IN02
IN01
IN00
AD8114
DUT
AVCC
AVCC
AVEE
AVCC
AVEE
AVCC
DATA_OUT
CE
DATA_IN
.01μF
C32
DVCC
.01μF
C10
.01μF
C17
C23
.01μF
.01μF
C16
C15
.01μF
.01μF
C14
C1
.01μF
.01μF
C6
AVEE
AVCC
AVEE
D4
D3
D2
D1
D0
A3
A2
A1
A0
SER/PAR
RESET
CE
DATA_OUT
CLK
DATA_IN
UPDATE
DGND1
DGND2
DVCC
CE
RESE T
P3
P3
P3
P3
DGND
P3
UPDATE
P2
P2
P2
P2
P2
RESET
CLK
P2
SER/PAR
P3
P1
P3
P3
P3
P3
P3
P3
P3
P3
D0
D1
D2
D3
D4
R26
75Ω
.01μF
C13
20K
R33
J32
J31
J30
J29
J28
J27
J26
J25
R28
75Ω
J24
J23
J22
J21
J20
J19
J18
J17
C19
.01μF
J16
J15
J14
J13
.01μF
C37
C36
.01μF
J12
C18
.01μF
.01μF
C35
J11
J4
J10
J9
J8
J7
J6
J5
J3
J2
J1
C34
.01μF
.01μF
C20
75Ω
R7
P1
AVCC
TP104
AVEE
AGND
P1
.01μF
C22
10μF
C5
.01μF
C21
C12
.01μF
.1μF
C3
R23
75Ω
75Ω
R24
75Ω
R20
75Ω
R21
R22
75Ω
75Ω
R17
75Ω
R18
DVCCDVCC
DGNDDGND
C9
.01μF
C11
.01μF
AGNDAGN D P1
P1
AVEEAVEE
C8
10μF
AVCCAVCC
10μF
C7
C24
.01μF
R12
75Ω
75Ω
R13
R14
75Ω
75Ω
R15
R25
75Ω
R27
75Ω
DGND
DVCC
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
DGND
AGND
AGND
AGND
AGND
AGND
A1
A0
AGND
AVCC
AGND
AGND
AVEE
AVEE
AVCC
DGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
A3
A2
DGND
UPDATE
CLK
C25
.1μF
C26
.1μF
AVCC
DVCC
6
5
4
2
6
7
8
9
10
12
13
14
1
1
1
3
5
2
4
6
11
2
3
4
5
9
8
767778798081828384858687888990919293949596979899
75
74
73
72
71
70
769
68
67
66
65
64
63
62
61
60
6
59
58
57
56
55
54
53
52
51
50
5
49484746454443424140
4
39383736353433323130
3
29282726
25
24
23
22
21
20
2
19
18
17
16
15
14
13
12
11
100
10
1
12999-005
Figure 5. Evaluation Board Schematic
UG-818 AD8112-EVALZ/AD8113-EVALZ/AD8114-EVALZ/AD8115-EVALZ/ADV3205-EVALZ User Guide
Rev. 0 | Page 8 of 10
12999-006
Figure 6. AD8112-EVALZ/AD8113-EVALZ/AD8114-EVALZ/AD8115-EVALZ/ADV3205-EVALZ Evaluation Board, Top View
12999-007
Figure 7. AD8112-EVALZ/AD8113-EVALZ/AD8114-EVALZ/AD8115-EVALZ/ADV3205-EVALZ Evaluation Board, Bottom View
AD8112-EVALZ/AD8113-EVALZ/AD8114-EVALZ/AD8115-EVALZ/ADV3205-EVALZ User Guide UG-818
ORDERING INFORMATION
BILL OF MATERIALS
Table 1.
Item Quantity Reference Designator Description Stock Number
1 1 Printed circuit board 08-005957
2 6 C2, C3, C4, C25, C26, C27 0.1 µF ceramic chip capacitors ADS # 4-5-18
3 4 C5, C6, C7, C8 10 µF, tantalum chip capacitors ADS # 4-7-2
4 24 C1, C6, C9 to C24, C32 to C37 0.01 µF chip capacitors ADS # 4-5-105
5 32 R1 to R32 75 Ω chip resistors, 1/16 W, 1% ADS # 3-35-1
6 1 R33 20 kΩ chip resistor, 1/8 W, 1% ADS # 3-18-26
7 15 R34 to R48 50 Ω chip resistors, do not install these resistors unless another
parallel interface is used aside from the USB Board Z
ADS # 3-35-3
8 32 J1 to J32 75 Ω BNC connectors Do not install
9 1 P3 14-pin connector, straight ADS # 12-3-62
10 1 P1 7-pin connector, header ADS # 12-3-61
11 1 P2 6-pin connector, header ADS # 12-3-60
12 1 DUT1 IC AD8112, AD8113, AD8114, AD8115, or ADV3205 Do not install
13 1 AGND Test point, black ADS # 12-18-44
14 1 UPDATE Test point, brown ADS # 12-18-59
15 2 DVCC, DATA_IN Test points, red ADS # 12-18-43
16 2 CLK, AVCC Test points, orange ADS # 12-18-60
17 6 DATA_OUT, D0, D1, D2, D3, D4 Test points, yellow ADS # 12-18-32
18 2 DGND1, DGND2 Test points, green ADS # 12-18-61
19 2 AVEE, DATA_OUT Test points, blue ADS # 12-18-62
20 1 SER/PAR Test points, violet ADS # 12-18-63
21 5 CE, A0, A1, A2, A3 Test points, white ADS # 12-18-42
22 1 RESET Test points, grey ADS # 12-18-64
23 6 Not applicable Large, self adhesive bumper pads ADS # 31-1-3
24 2 W1, W2 2-pin headers, male ADS # 11-2-37
25 2 W1, W2 2-pin jumpers, female ADS # 11-2-38
Rev. 0 | Page 9 of 10
UG-818 AD8112-EVALZ/AD8113-EVALZ/AD8114-EVALZ/AD8115-EVALZ/ADV3205-EVALZ User Guide
NOTES
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2015 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG12999-0-3/15(0)
Rev. 0 | Page 10 of 10
