202
Optical disc ICs
2-channel BTL driver for CD players
BA6792FP / BA6792FP-Y
The BA6792FP and BA6792FP-Y are 2-channel BTL drivers for CD player actuator drives. HSOP 28 and 25-pin pack-
ages allow for compact applications.
Applications
CD players and CD-ROM drives
Features
1) 2 channel dedicated BTL drivers.
2) HSOP 28 and 25-pin power packages for compact
applications.
3) Gain is adjustable with an attached resistor.
4) Internal thermal shutdown circuit.
Absolute maximum ratings (Ta = 25C)
Recommended operating conditions (Ta = 25C)
203
Optical disc ICs BA6792FP / BA6792FP-Y
Block diagram
Pin descriptions (BA6792FP)
204
Optical disc ICs BA6792FP / BA6792FP-Y
Pin descriptions (BA6792FP - Y)
205
Optical disc ICs BA6792FP / BA6792FP-Y
Pin equivalent circuit diagrams
Electrical characteristics (unless otherwise noted, Ta = 25C, VCC = 8V, f = 1KHz, RL = 8Ω)
206
Optical disc ICs BA6792FP / BA6792FP-Y
Measurement circuit
207
Optical disc ICs BA6792FP / BA6792FP-Y
Application example (BA6792FP)
Operation notes
(1) The BA6792FP and BA6792FP-Y have an internal
thermal shutdown circuit. The output current is muted
when the chip temperature rises above 175C (typically).
The driver circuit is restored when the chip temperature
rises above 150C (typically).
(2) The output current can be muted by opening the
mute pin voltage or lowering it below 0.5V. This pin
should be pulled up above 2.0V during normal operation.
(3) Muting also occurs when the bias pin voltage drops
below 1.4V (typically). This pin should stay above 2.0V
during normal operation.
(4) Muting occurs during thermal shutdown, mute-on
operations or a drop in the bias pin voltage. In each case,
only the drivers are muted. During muting, the output pins
remain at the internal bias voltage, roughly (VCC / 2).
(5) Attach a bypass capacitor (roughly 0.1µF) between
the power supplies, at the base of the IC.
(6) The radiating fin is connected to the package’s in-
ternal GND, but should also be connected to an external
ground.
208
Optical disc ICs BA6792FP / BA6792FP-Y
Electrical characteristic curves
External dimensions (Units: mm)
Appendix
Appendix1-Rev1.0
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level of
reliability and the malfunction of with would directly endanger human life (such as medical instruments,
transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other
safety devices), please be sure to consult with our sales representative in advance.
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document use silicon as a basic material.
Products listed in this document are no antiradiation design.
About Export Control Order in Japan
Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control
Order in Japan.
In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause)
on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.
