POWER
Intelligent MP Series
Up to 1500 Watts
Total Power: Up to 1500 W
Input Voltage: 85 - 264 VaC
88 - 300 Vdc
# of Outputs: Up to 24
SPECIAL FEATURES
Full medical EN60601 approval
Intelligent I2C control
Voltage adjustment on all outputs
(manual or I2C)
Configurable input and output OK
signals and indicators
Configurable inhibit/enable
Configurable output UP/DOWN
sequencing
Configurable current limit
(foldback or constant current)
High power density (8.8 W/cu-in)
Intelligent fan (speed control/fault
status)
Downloadable GUI from website
Customer provided air option
uP controlled PFC input with active
inrush protection
I2C monitor of voltage, current, and
temp
Programmable voltage, current limit,
inhibit/enable through I2C
Optional extended hold-up module
(SEMI F47 compliance)
Increased power density to 50% over
standard MP
External switching frequency sync input
Optional conformal coating
Industrial temp range (-40 ºC to 70 ºC)
No preload required
Industrial shock/vibration (> 50G’s)
SAFETY
UL UL60950/UL2601**
CSA CSA22.2 No. 234 Level 5
UV EN60950/EN60601-1**
BABT Compliance to
EN60950/
EN60601 BS7002
CB Certificate and report
CE Mark to LVD
Data Sheet
Electrical Specications
Input
Input ra nge 85 - 264 Vac 88 - 300 Vdc
(limited to 300 Vdc in medical applications)
Frequency 47 - 440 Hz
Inrush current 40 A peak maximum (soft start)
Efciency Up to 85% @ full case load
Power Factor 0.99 typ. meets EN61000-3-2 (n/a @ 440 Hz)
Turn-on time AC on 2.0 sec typ., inhibit/enable 150 ms typical
Programmable delay; 50 ms internal turn-on delay (Dual Output only)
EMI lter CISPR 22/EN55022 Level “B”**
Leakage current 300 µA max. @ 240 Vac; 47 - 63 Hz
Radiated EMI CISPR 22/EN55022 Level “B”**
Holdover storage 20 ms minimum (independent of input Vac) additional 34 ms holdover
storage with optional HUP module (SEMI F47 compatible).
For iMP4 15 ms (low-line), 10 ms (high-line)
AC OK > 5 ms early warning min. before outputs lose regulation
Full cycle ride thru (50 Hz) (n/a on iMP4 > 750 W @ 90 Vac)
Harmonic distortion Meets EN61000-3-2
Isolation Meets EN60950 and EN60601
Input to output, input to ground: 2000 Vac; output to ground: 400 Vdc
Global inhibit / enable TTL, Logic “1” and Logic “0”; congurable
Input fuse (internal) iMP4: 16 A; iMP8: 20 A; iMP1: 25 A (both lines fused)
Warranty 2 years
iMP Data Sheet
Electrical Specications
Environmental Specications
Operating temperature -40 ° to 70 °C ambient. Derate each output 2.5% per degree from 50 ° to 70 °C. (-20 °C start up)
Storage temperature -40 °C to +85 °C
Electromagnetic susceptibility Designed to meet EN61000-4; -2, -3, -4, -5, -6, -8, -11 Level 3
Humidity Operating; non-condensing 10% to 95% RH
Vibratio IEC68-2-6 to the levels of IEC721-3-2
MTBF demonstrated: > 550,000 hours at full load, 220 Vac and 25 °C ambient conditions
Output Module Line-up
Module Code 1 2 3 5 4 —
Module Type Single Single Single Single Dual Triple
Max output power 210 W 360 W 750 W 1500 W 144 W 36 W
Max output current 35 A 60 A 150 A 140 A 10 A 2 A
Output voltages available* 2 - 60 V 2 - 60 V 2 - 60 V 6 - 60 V 8 - 15*, 24 - 28; 8 - 15*, 8 - 15*;
8 - 15*, 2 - 6; 2 - 6, 2 - 6; 24 - 28,
24 - 28; 24 - 28, 2 - 6
8-15, 8-15, 2-6; 8-15, 8-15, 8-15;
8-15, 8-15, 18-28; 8-15, 18-28, 2-6
Standard voltage increments 25 25 25 18 16 18
Remote sense Yes Yes Yes Ye s Yes Yes No
Remote margin Yes Yes Yes Ye s No No No
V-Program - I2C Control Yes Yes Yes Ye s Yes Yes No
Active Current Share Yes Yes Yes Ye s Yes No No
Module Inhibit - I2C Control Yes Yes Yes Ye s Yes Yes Yes
Module Inhibit - Analog Yes Yes Yes Ye s Yes No No
Overvoltage/Overcurrent protection Yes Yes Yes Yes Yes Yes Yes
Minimum load required No No No No No No No
Slots occupied in any iVS case 1 2 3 4 1 1
* Note: Contact Factory for extended range down to 6 V
Output
Adjustment range* ± 10% minimum all outputs (manual)
(full module adjustment range using I2C)
Factory set point accuracy 1%
I2C output program
accuracy
± 5%
Margining ± 4 - 6% nominal analog (single output
module only)
Overall regulation 0.4% or 20 mV max. (1500 W modules 1%
max.) (36 W modules 4% maximum)
Ripple RMS: 0.1% or 10 mV, whichever is greater
Pk-Pk: 1.0% or 50 mV, whichever is greater
Bandwidth limited to 20 MHz
Dynamic response < 2% or 100 mV, with 25% load step
Recovery time To within 1% in < 300 µsec
Overcurrent protection** Congurable through I2C (calibration
required). Single output module and main
output of the dual output module 105 - 120%
of rated output current. Aux output of dual
output module 105 - 140% of rated output
current
Short-circuit protection: Protected for continuous short-circuit.
Recovery is automatic upon removal of short
Overvoltage protection* Congurable through I2C
Single output module:
2 - 5.5 V 122 - 134%; 6 - 60 V 110 - 120%
Dual output module:
2 - 6 V 122 - 134%; 8 - 28 V 110 - 120%
Triple output module:
110 - 120% of highest voltage rating
Output (cont.)
Reverse voltage protection: 100% of rated output current
Thermal protection*
(OTP and OTW)
Congurable through I2C
All outputs disabled when internal temp
exceeds safe operating range. > 5 ms
warning (AC OK signal) before shutdown
Remote sense Up to 0.5 V total drop (not available on triple
output module)
Single wire parallel Current share to within 2% of total rated
current
DC OK* ± 5% of nominal. Congurable through I2C
Minimum load Not required
Housekeeping bias voltage 5 Vdc @ 1.0 A max. present whenever AC
input is applied (Optional 2.0 A available)
Module inhibit* Congured and controlled through I2C
Switching frequency 250k Hz accepts external sync signal
Output/Output isolation > 1 Megohm, 500 V
External sync TTL clock input signal used to adjust
switching frequency. Frequency 500 kHz
± 20%; Duty cycle 40 - 55%
* Can be controlled via I2C
** Controlled via I2C but requires load calibration
iMP Data Sheet
Ordering Information
Ordering Notes:
1. The cases and modules of both MP and iMP series can
be interchanged to allow more exibility. If intelligent
modules are used with non-intelligent cases, a numeric
code “4” is placed at the end of the module code (ex.
4LL0 becomes 4LL4).
2. USB to I2C module order code 73-769-001
7 6 5 4 3 2 1
iMP4
available slots
iMP8
available slots
Slot 1
Slot 2
Slot 3
Slot 4
Slot 5
Slot 1
Slot 2
Slot 3
Slot 4
Slot 5
Slot 6
Slot 2
Slot 3
Slot 4
Slot 6
Slot 7
Slot 5
iMP1
available slots
Parallel Codes
0 = no parallel
1 = 1 & 2
2 = 2 & 3
3 = 3 & 4
4 = 4 & 5
5 = 3 & 4 & 5
6 = 5 & 6
7 = 4 & 5 & 6
8 = 6 & 7
9 = 3 & 4, 6 & 7
A = 1 & 2, 3 & 4, 5 & 6
C = 2 & 3, 4 & 5
E = 3 & 4, 5 & 6
F = 2 & 3, 4 & 5, 6 & 7
iMP1* - 3L0 - 2E2 - 1Q1 - 4LL0 - 00 - A - ###
Case Size (mm)
4 = 2.5” x 5” x 10”; 750 W - 1158 W, 5 Slots
(63.5 x 127 x 254 mm)
8 = 2.5” x 7” x 10”; 1000 W - 1200 W,
6 Slots (63.5 x 177.8 x 254 mm)
1 = 2.5” x 8” x 11”; 1200 W - 1500 W,
7 Slots (63.5 x 203.2 x 279.4 mm)
Module Codes
Module/voltage/option codes
Module codes:
(None) = 36 W triple O/P (1 slot)
1 = 210 W single O/P (1 slot)
2 = 360 W single O/P (2 slot)
3 = 750 W single O/P (3 slot)
4 = 144 W dual O/P (1 slot)
5 = 1500 W single O/P (4 slot)
6 - 9 = future
Case Option Codes
First digit
0 - 9, A - Z parallel code
(See Parallel Codes table above)
Second digit
0 = No options
1 = Reverse air
3 = Global enable
4 = Fan idle with inhibit
5 = Opt 1 + Opt 3
6 = Opt 1 + Opt 4
7 = Opt 3 + Opt 4
8 = Opt 1 +3 +4
9 = RS485 73-544-002
C = Opt 3 + Opt 9
D = CAN BUS 73-544-003
E = Opt 3 + Opt D
Software Code
Voltage Codes:
See Output Module Voltage/Current
table above
Option Codes:
0 = Standard
1 = Module enable
2 = Constant current
3 = 1 & 2 combined
4 = Set for use in standard
(non-intelligent case)
5 = Shutdown mode for 1500 W
6 = 1 & 5 combined
7 - 9 = future
Module/Voltage/Option Codes
First - Module Code
Second - Voltage Code
Third - Option Code Case Option CodesCase Size
Factory assembled
for hardware of
firmware mods.
Hardware Code
* Note: Add “E” after iMP4 to denote IEC input option.
e.g. iMP4E (Not available on iMP8 or iMP1)
Software code
used for
configuration
change. “A” is
standard
Output Module Voltage/Current*
Voltage Voltage
Code Single Output Module Code Dual
Output*** Triple Output I2C
Adjustment
Ranges****
1 2 3 5 4 4 - - -
2 V A 35 A 60 A 150 A 300 A 10 A 10 A — — 2 A 1.8 - 2.2
2.2 V B 35 A 60 A 150 A 300 A 10 A 10 A — — 2 A 2.0 - 2.4
3 V C 35 A 60 A 150 A 300 A 10 A 10 A — — 2 A 2.7 - 3.3
3.3 V D 35 A 60 A 150 A 300 A 10 A 10 A — — 2 A 3.0 - 3.6
5 V E 35 A 60 A 150 A 300 A 10 A 10 A — — 2 A 4.5 - 5.5
5.2 V F 35 A 60 A 144 A 288 A 10 A 10 A — — 2 A 4.7 - 5.7
5.5 V G 34 A 58 A 136 A 273 A 10 A 10 A — — 2 A 5.0 - 6.1
6.0 V H 23 A 42 A 97.5 A 250 A 10 A* 10 A* — — 2 A 5.4 - 6.6
8.0 V I 20 A 36 A 84.4 A 140 A 10 A 4 A 1 A 1 A 1 A 7.2 - 8.8
10 V J 18 A 32 A 75 A 140 A 10 A 4 A 1 A 1 A 1 A 9.0 - 11.0
11 V K 17 A 31 A 68 A 136.3 A 10 A 4 A 1 A 1 A 1 A 9.9 - 12.1
12 V L 17 A 30 A 62.5 A 125 A 10 A 4 A 1 A 1 A 1 A 10.8 - 13.2
14 V M 14 A 21 A 53.5 A 107 A 9 A 4 A 1 A 1 A 1 A 12.6 - 15.4
15 V N 14 A 20 A 50 A 100 A 8 A 4 A 1 A 1 A 1 A 13.5 - 16.5
18 V O 11 A 19 A 41.6 A 83.3 A — — — 0.5 A 0.5 A 16.2 - 19.8
20 V P 10.5 A 18 A 37.5 A 75 A — — — 0.5 A 0.5 A 18.0 - 22.0
24 V Q 8.5 A 15 A 30 A 62.5 A 4 A 2 A — 0.5 A 0.5 A 21.6 - 26.4
28 V R 6.7 A 11 A 26.8 A 53.5 A 3 A 2 A — 0.5 A 0.5 A 25.2 - 30.8
30 V S 6.5 A 11 A 25 A 50 A — — — — — 27.0 - 33.0
33 V T 6.2 A 10.9 A 22.7 A 35.8 A — — — — — 29.7 - 36.3
36 V U 5.8 A 10 A 20.8 A 35.8 A — — — — — 32.4 - 39.6
42 V V 4.2 A 7.5 A 16 A 35.7 A — — — — — 37.8 - 46.2
48 V W 4.0 A 7.5 A 15.6 A 31.2 A — — — — — 43.2 - 52.8
54 V X 3.7 A 6.0 A 13.9 A 27.7 A — — — — — 48.6 - 59.4
60 V Y 3.5 A 6.0 A 12.5 A 25 A — — — — — 54.0 - 66.0
Contact Factory
Special* Z 35 A 60 A 150 A 300 A — 10 A 2.3 - 2.6
Special* Z 35 A 60 A 150 A 300 A — 10 A 3.7 - 4.4
Special* Z 20 A 36 A 80 A 140 A — 8 A 6.7 - 7.1
* Note: Contact Factory for extended range down to 6 V.
** Increments of current not shown can be achieved by paralleling modules (add currents of each module selected).
*** Total output power on dual model must not exceed 144 W.
**** For single output modules only.
iMP Data Sheet
iMP4 (AC input on opposite side)
iMP8 and iMP1
210 W
360 W
750 W
1500 W
144 W 36 W
Pin Connectors
AC Input
Pin No. Function
1 AC neutral
2 AC line (hot)
3 Chassis (earth) ground
PFC Input Connector (control and signals)
Pin No. Function
1 Input AC OK - “emitter”
2 Input AC OK - “collector”
3 Global DC OK - “emitter”
4 Global DC OK - “collector”
5 External Sync
6 Global inhibit/optional enable logic “0”
7 Global inhibit/optional enable logic “1”
8 Global inhibit/optional enable return
9 +5 VSB housekeeping
10 +5 VSB housekeeping return
I2C Bus Output Connector
Pin No. Function
1 No connection
2 No connection
3 No connection
4 Serial clock signal (SCL)
5 Serial data signal (SDA)
6 Address bit 0 (A0)
7 Address bit 1 (A1)
8 Address bit 2 (A2)
9 Secondary return (GND)
10 5 Vcc external bus (5 VCC. Bus)
Single
TripleDual
Input
85 - 264 Vac 180 - 264 Vac
iMP8 = 2.5” x 7” x 10” 6 available slots 1000 W max. 1200 W max.
(63.5 x 177.8 x 254 mm)
iMP1 = 2.5” x 8” x 11” 7 available slots 1200 W max. 1500 W max.
(63.5 x 203.2 x 279.4 mm)
S
L
O
T
7
S
L
O
T
5
S
L
O
T
6
S
L
O
T
4
S
L
O
T
3
S
L
O
T
2
S
L
O
T
1
-A-
S
L
O
T
S
L
O
T
S
L
O
T
S
L
O
T
S
L
O
T
54321
iMP1 only
AC input
Mates with
Molex 90142-0010 Housing
90119-2110 Pin
Connector Kit Part No.:
70-841-004
Mates with
Landwin 2050S1000 Housing
2053T011V Pin
or
JST PHDR-10VS Housing
JST SPHD-002T-P0.5 (28-24)
JST SPHD-001T-P0.5 (26-22)
Connector Kit Part No.:
70-841-023
Figure 1. AC Input
Figure 2. Connector J1
Figure 3. Connector J2
Input
90 - 264 Vac 180 - 264 Vac
iMP4 = 2.5” x 5” x 10” 5 available slots 750 W max. 1158 W max.
(63.5 x 127 x 254 mm)
6
1
10
5
Figure 3. Connector J2
12
73
Figure 4. Connector CN50x
1
2
3
~
N
10
5
iMP Data Sheet
Mechanical Drawings
.63”
(16.0)
.32”
(8.1)
1.38” (35.2)
(2X)
.44”
(11.4)
.48” (12.1)
(2X)
.33”
(8.5)
V ADJ
V-
V+
M 4 X 8 SCREWS
WITH CONICAL
WASHER
DC OUTPUT
CONNECTOR
PIN 1
.44"
(11.4)
.32"
(8.1)
1.38"
(35.1)
.48"
(12.1)
.44” (11.2)
2X
V+
M4X8 SCREWS WITH CONICAL WASHER
DC OUTPUT CONNECTOR
PIN 1
V-
V ADJ
PIN 1
V2 ADJ
.32
(8.1)
.42 (10.7)
V1 +
V1 -
V2 +
M3X8 SCREWS WITH SPRING WASHER
(4X)
.46 (11.7)
(4X)
.30 (7.5)(3X)
V1 ADJ
1.17 (29.7)
V2 -
Dual 144 Watt
Single 360 Watt Single 1500 Watt 8 - 60 VSingle 750 Watt
Triple 36 Watt
.32"
(8.1)
.44"
(11.0)
1.24"(31.5)
(2X)
.61"(15.6)
(2X)
.59"
(15.0)
.63"
(16.0)
DC OUTPUT
CONNECTOR
PIN 1 V ADJ M4X8 SCREWS
(4X)
V-
V+
V1 +
V1 -
V2 -
V3 -
V3 +
V
2 +
V-
V+
59.3 ± 0.2
(2x) 15.0 ±0.8
(2x) 16.0 ±0.2
(2x) 16.0 ±0.2
(3x) 31.6 ±0.8
11.3 ±0.8
8.1 ±0.8
DC OUTPUT CONNECTOR
PIN 1
M4X8 SCREWS W/
CONICAL WASHER (6X)
For Factory-Use Only
VADJ
Single 210 Watt
iMP Modules
DC-DC Converter Output Modules
Mates with
Molex 90142-0010 Housing
90119-2110 Pin
Mates with
Molex 09-91-0600 Housing
26-60-5060 Pin
Figure 4. Connector J1
Control Signal Information, J1 Control Connector
Pin No. Function
1 + Remote Sense single or dual o/p main
2 Remote Margin / V. Program single o/p
3 Margin High single o/p
4 - Remote Sense / Margin Low single or dual o/p main
5 Spare
6 Module, Isolated Inhibit single or dual o/p
7 Module Inhibit Return single or dual o/p
8 Current Share (SWP) single or dual o/p main
9 + Remote Sense V2 dual o/p, single is spare
10 - Remote Sense V2 dual o/p, single is spare
* Note: All iMP modules have a green DCOK LED. (except for 36 W module)
Figure 1. AC Input
1
2
3
~
N
6
1
10
5
Figure 2. Connector J1
V1 ADJ
V2 ADJ
V3 ADJ
V1+
V3+
V1-
V2+
V2-
V3-
iMP Data Sheet
iMP Series
iMP4 (750/1158 Watts Max) 5-Inch Case Size: iMP4: 2.5” x 5” x 10” (63.5 mm x 127 mm x 254 mm)
Weight: iMP4 Case: 3 lbs. • 360 W Single 1.0 lb. • 750 W Single: 1.6 lbs. 144 W Dual: 0.6 lb.
Notes:
1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs. (0.67 N-m). (Optional IEC input connector)
2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector kit includes
mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with 2053T011P (Landwin) pins or
JST PHDR-IOVS Housing and JST SPHD-002T-PO.5 pins.
3. Chassis material: aluminum with chemical lm coating (conductive).
4. All dimensions are in millimeters and inches, and are typical.
5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.150” (3.8 mm). Max. torque: 5 in-lbs. (0.57 N-m).
6. Output module connections: All single O/P modules are M4 x 8 mm screws. Max. torque: 10 in-lbs. (1.13 N-m).
Dual O/P module is M3 x 8 mm screws. Max. torque: 5 in-lbs. (0.57 N-m).
iMP Data Sheet
iMP Series
iMP8 (1000/1200 Watts Max) 7-Inch Case Size: iMP8: 2.5” x 7” x 10” (63.5 mm x 177.8 mm x 254 mm)
Weight: iMP8 Case: 4.1 lbs. • 210 W Single: 0.6 lb. • 360 W Single: 1.0 lb.
• 750 W Single: 1.6 lbs. 144 W Dual: 0.6 lb.
Notes:
1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs. (0.67 N-m).
2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series)
Connector kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with
2053T011P (Landwin) pins or JST PHDR-IOVS Housing and JST SPHD-002T-PO.5 pins.
3. Chassis material: aluminum with chemical lm coating (conductive).
4. All dimensions are in millimeters and inches, and are typical.
5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.150” (3.8 mm). Max. torque: 5 in-lbs. (0.57 N-m).
6. Output module connections: All single O/P modules are M4 x 8 mm screws. Max. torque: 10 in-lbs. (1.13 N-m).
Dual O/P module is M3 x 8 mm screws. Max. torque: 5 in-lbs. (0.57 N-m).
xy
xx
x
y
y
y
171.45
171.45
177.8
19.05 M4 MOUNTING HOLES (4X)
MARKED AS X
#8-32 MOUNTING HOLES
(4X) MARKED AS Y
M4 MOUNTING HOLES (4X)
IDENTICAL BOTH SIDES
38.10
Normal Air Flow
Reverse Air Flow
iMP Data Sheet
iMP Series
iMP1 (1200/1500 Watts Max) 8-Inch Case Size: iMP1: 2.5” x 8” x 11” (63.5 mm x 203.2 mm x 279.4 mm)
Weight: iMP1 Case: 5.0 lb. • 210 W Single: 0.6 lb. • 360 W Single: 1.0 lb.
• 750 W Single: 1.6 lb. • 144 W Dual: 0.6 lb.
Notes:
1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs (0.67 N-m).
2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector kit includes
mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with 2053T011P (Landwin) pins or
JST PHDR-IOVS Housing and JST SPHD-002T-PO.5 pins.
3. Chassis material: aluminum with chemical lm coating (conductive).
4. All dimensions are in millimeters and inches, and are typical.
5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.150” (3.8 mm). Max. torque: 5 in-lbs. (0.57 N-m).
6. Output module connections: All single O/P modules are M4 x 8 mm screws. Max. torque: 10 in-lbs.
(1.13 N-m). Dual O/P module is M3 x 8 mm screws. Max. torque: 5 in-lbs. (0.57 N-m).
WORLDWIDE OFFICES
Americas
2900 S.Diablo Way
Tempe, AZ 85282
USA
+1 888 412 7832
Europe (UK)
Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX
United Kingdom
+44 (0) 1384 842 211
Asia (HK)
14/F, Lu Plaza
2 Wing Yip Street
Kwun Tong, Kowloon
Hong Kong
+852 2176 3333
For more information: www.artesyn.com/power
For support: productsupport.ep@artesyn.com
www.artesyn.com
iMP Data Sheet
While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn
Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use
of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn
Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc.
All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective
owners. © 2014 Artesyn Embedded Technologies, Inc. iMP DS Rev. 27Mar2015
The RS485/CAN-to-I2C uses 2 Input Protocols and 1
Output Protocol.
The Input Protocols used are RS485 using Modbus
(Command Index: 0x01), and CAN using modied Modus
(Command Index: 0x02).
The Output Protocol use is: I2C with SMBus support
(Command Index: 0x80).
Master/Client Device(s)
Adapter
Output Protocols
Slave/Server Device(s)
Adapter Protocol
Input Protocols
Ada
p
ter Command
RS485 using
Modbus
Ada
p
ter Controls
CAN using
Modied Modbus
I
2
C with SMBus
Support
iMP CAN RS485
Optional CANBUS or RS485 Interface
RS485/CAN - to - I2C
For Detailed Info, Download the Software Requirements
Specication (SRS) from http://www.artesyn.com/power/power-
supplies/cat/101/Congurable-Power-Supplies-iMP-Series