CKD-38-30010 - TE CONNECTIVITY

1224 Dimensions are shown for

reference purposes only. Dimensions are in inches over

(millimeters) unless otherwise

specified.

Specifications and availability

subject to change.

P&B

Catalog 1308242

Issued 3-03

www.tycoelectronics.com

Technical support:

Refer to inside back cover.

Initial Dielectric Strength

Between Open Contacts: 500V rms, 60 Hz.

Between All Other Conductors: 500V rms, 60 Hz.

CK series

Mid-Priced CMOS IC Time Delay Relay

•Choice of timing modes

– Delay on operate

– Delay on release

– Delay on dropout (no input required during timing)

– Interval on

•Knob or resistor adjustable types

•10A output relay with DPDT contacts

•Various models time from 0.1 to 180 sec.

File E22575

File LR15734

Contact Data @ 25°C

Arrangements: 2 Form C (DPDT).

Material: Silver-cadmium oxide alloy.

Rating: 10A @ 30VDC or 277VAC, resistive; 1/2 HP @ 250VAC; 1/3 HP @

120VAC.

Expected Mechanical Life: 10 million operations.

Expected Electrical Life: 100,000 operations, min., at rated load.

Input Data @ 25°C

Voltage: 24 & 120VAC and 12 & 24VDC.

Power Requirement: AC Types: Typically less than 3 VA.

DC Types: Typically less than 3 W.

Initiate Time: Delay on dropout timers must have input voltage applied for

a minimum of three seconds for dropout function to be

guaranteed.

Transient Protection: Yes.

Reverse Voltage Protection: Yes.

Environmental Data

Temperature Range: Storage: -55°C to +85°C.

Operating: -10°C to +55°C.

Mechanical Data

Termination: 8- or 11-pin octal style plug.

Enclosure: White plastic case. Knob adjustable types have dial scale for

reference only.

Sockets: Models with 8-pin base fit either 27E122 or 27E891 (snap-on)

screw terminal sockets. 11-pin types fit either 27E123 or

27E892 (snap-on) screw terminal sockets.

Weight: 6 oz. (170g) approximately.

Timing Modes

Delay on operate – Delay period begins when input voltage is applied. At

the end of the delay period, the relay will operate and will not release until

input voltage is removed. Reset occurs when input voltage is reapplied.

Delay on release – Input voltage must be applied continuously to operate

the internal relay. When the control switch is closed, the relay energizes.

When the control switch is opened, timing begins. When timing is

complete, the relay will de-energize. Time may be reset to zero during

timing by closing the control switch.

Delay on dropout – The relay operates immediately upon application of

input voltage. Timing begins when input voltage is removed. When timing

is complete, the relay will de-energize. Reset occurs when input voltage is

reapplied.

Interval on (with control switch) – Input voltage must be applied

continuously to operate the internal relay. The relay energizes and timing

begins when the external switch is closed. At the end of the time delay

period the relay will de-energize. Reset is accomplished by opening and

reclosing the control switch.

Timing Specifications

Timing Ranges: From 0.1 to 180 sec.

Timing Adjustment: External resistor and knob adjustable.

Tolerance (for AC units add ±1/2 cycle 60 Hz.):

Knob Adj. Types:–0, +20% of max. specified at high end of timing range;

min. specified, or less, at low end.

Fixed Types: ±5%.

Res. Adj. Types: ±5% at high end of timing range; min. specified, or less,

at low end.

Delta Time (for AC units add ±1 cycle 60 Hz.): ±10%.

Repeatability (for AC units add ±1 cycle 60 Hz.): ±2%.

Release Time: 60 ms, typ.; 100 ms, max.

Recycle Time: 60 ms, typ.; 100 ms, max.

Input Voltages & Limits @ 25°C

TIME

INPUT

VOLTAGE ON

OFF

N.O. RELAY

CONTACTS ON

OFF

CONTROL

SWITCH ON

OFF

N.O. RELAY

CONTACTS TIME

TIME

INPUT

VOLTAGE ON

OFF

N.O. RELAY

CONTACTS ON

OFF

CONTROL

SWITCH ON

OFF

N.O. RELAY

CONTACTS

➛

Voltage Nominal Minimum Maximum

Type Voltage Voltage Voltage

AC 24 20 28

120 105 130

DC 12 11 13

24 20 32

Note: DC voltage must be filtered (5% p-p ripple max. at nom. voltage).

AC models will operate on 50 or 60 Hz.

Users should thoroughly review the technical data before selecting a product part

number. It is recommended that user also seek out the pertinent approvals files of

the agencies/laboratories and review them to ensure the product meets the

requirements for a given application.

1225

Dimensions are shown for

reference purposes only. Dimensions are in inches over

(millimeters) unless otherwise

specified.

Specifications and availability

subject to change. www.tycoelectronics.com

Technical support:

Refer to inside back cover.

P&B

Catalog 1308242

Issued 3-03

Wiring Diagrams – Bottom Views (pins numbered clockwise from keyway)

* If control switch is closed when power is applied, relay will immediately energize. A 50 millisecond minimum switch closure is required. IMPORTANT: A dry circuit switch is recommended. A “dry

circuit” switch is one rated to reliably switch currents of less than 50mA. Use of a switch rated for other than dry circuit may result in failure of the time delay relay to function properly.

** Note: Input polarity for DC operation. For most reliable operation on AC, connect high side to “+” and low side to “–”.

Ordering Information – Authorized distributors are more likely to stock boldface items listed below.

Outline Dimensions

External Resistor Chart

See External Resistor Selection Charts at beginning of Time Delay Relay section of this Databook.

Delay On Operate Models

Voltage Time Adjustment Wiring Dia. Part Number

24VAC 0.1 to 10 Sec. Knob 1 CKB-38-30010

0.1 to 10 Sec. CKB-38-70010

120VAC 0.6 to 60 Sec. Knob 1 CKB-38-70060

1.2 to 120 Sec. CKB-38-70120

1.8 to 180 Sec. CKB-38-70180

120VAC 0.1 to 10 Sec. Resistor 2 CKF-38-70010

12VDC 0.1 to 10 Sec. Knob 1 CKD-38-20010

Delay On Release Models

Voltage Time Adjustment Wiring Dia. Part Number

0.1 to 10 Sec. CKB-38-78010

120VAC 0.6 to 60 Sec. Knob 3 CKB-38-78060

1.8 to 180 Sec. CKB-38-78180

120VAC 0.1 to 10 Sec. Resistor 4 CKF-38-78010

24VDC 0.1 to 10 Sec. Resistor 4 CKH-38-38010

Delay On Dropout Models

Voltage Time Adjustment Wiring Dia. Part Number

24VAC 0.1 to 10 Sec. Knob 1 CKB-38-37010

0.6 to 60 Sec. CKB-38-37060

0.1 to 10 Sec. CKB-38-77010

120VAC 0.6 to 60 Sec. Knob 1 CKB-38-77060

1.2 to 120 Sec. CKB-38-77120

Interval On Models

Voltage Time Adjustment Wiring Dia. Part Number

120VAC 0.1 to 10 Sec. Knob 3 CKB-38-79010

.60

(15.2) .56

(14.2)

2.937 MAX.

(74.6)

2.406 MAX.

(61.1)

1.781 MAX.

(45.2)

➛

INPUT

(DC POLARITY INDICATED)**

Fig.1

8 Pin

EXTERNAL RESISTOR

INPUT

(DC POLARITY INDICATED)**

Fig. 2

11 Pin

CONTINUOUS

SUPPLY

INPUT

(DC POLARITY INDICATED)**

EXTERNAL

CONTROL

SWITCH*

Fig. 3

11 Pin

CONTINUOUS

SUPPLY

INPUT

(DC POLARITY INDICATED)**

EXTERNAL

CONTROL

SWITCH*

Fig. 4

11 Pin

EXTERNAL RESISTOR

➛