12 11 10 9 8 7 5 6 4 2 1 63.25 REFERENCE 115.54 REFERENCE H 3 14.00 0.10 TYPICAL H CLASS "A" SEE NOTE 6 3.28 REFERENCE 9.00 0.10 TYPICAL 26.25 REFERENCE G 25.83 REF 25.20 0.20 G 9.00 0.10 TYPICAL 2.07 0.25 SIGNALS TYPICAL 3.05 GROUNDS TYPICAL SEE DETAIL B F 11.50 REFERENCE SEE NOTE 7 F DATE CODE LOCATION 8 PLACES SEE NOTE 9 NOTES: 1. MATERIAL: CAGE: NICKEL SILVER, THICKNESS: 0.25mm CONNECTOR HOUSING: GLASS FILLED, LIQUID CRYSTAL POLYMER (LCP), UL 94V-0 COLOR: BLACK OVERMOLDED TERMINAL HOUSING: GLASS FILLED, LIQUID CRYSTAL POLYMER (LCP), UL 94V-0, COLOR: BLACK TERMINALS: TIN BRASS LIGHT PIPES: POLYCARBONATE, UL 94V-0, COLOR: CLEAR LIGHT PIPE HOUSING: ZINC 2. FINISH: LIGHT PIPE HOUSING: 150 MICROMETERS MINIMUM NICKEL OVER 150 MICROMETERS MINIMUM COPPER TERMINALS: CONTACT AREA: 0.76 MICROMETERS MINIMUM HARD GOLD OVER 1.27 MICROMETERS MINIMUM NICKEL. COMPLIANT TAIL - 0.76 - 1.52 MICROMETERS MATTE TIN OVER 0.76 - 1.52 MICROMETERS NICKEL 3. REFER TO PS-75310-001 PRODUCT SPEC FOR ALL ELECTRICAL, MECHANICAL AND ENVIRONMENTAL SPECIFICATIONS. 4. LIGHT PIPE PAD LAYOUT IS FOR 0805 LOW-PROFILE LED PACKAGE, FOR OTHER RECOMMENDED LAYOUTS REFER TO MOLEX'S REPORT TS-75310-001. 5. REFER TO PK-76352-001 FOR ALL PACKAGING SPECIFICATIONS. 6. ALL EXTERIOR SURFACES TO BE CLASS "B" SURFACE EXCEPT THE UNDER SIDE OF THE CAGE WHERE THE PCB WOULD BE LOCATED AND AS NOTED. THE SURFACES TO CONFORM TO THE MOLEX COSMETIC DOC PS-45499-002. 7. THE OVERALL CAGE WIDTH AT THE VERTICAL CENTER OF THE FRONT EDGE WILL FALL WITHIN THIS DIMENSION: 114.80+/-0.30 MM. THIS PORTION OF THE CAGE WILL FLEX INWARD AS THE CAGE IS BEING INSERTED INTO THE BEZEL OPENING. 8. REFER TO AS-76090-001 FOR HIGH SPEED ROUTING RECOMMENDATIONS. 9. DATE CODE LOCATION IS SHOWN ABOVE. DATE CODE FORMAT: DDDY MX A1 DDD = DAY OF THE YEAR Y = YEAR MX = MOLEX A = ALPHA CHARACTER - INDICATES MANUFACTURING LINE 1 = NUMERIC CHARACTER - INDICATES PRODUCTION SHIFT E D C B E D C PART NUMBER LIGHTPIPE CONFIGURATION (SEE VIEWS ON SHEET 2) 763527001 4 LIGHT PORTS 763527002 INNER 2 PORTS 763527003 OUTER 2 PORTS B SYMBOLS = 0 = 0 = 0 A P1 RELEASE DATE 11 2018/06/01 10 22:27:30 C 9 8 7 6 mm 2:1 = 0 4 PLACES = 0 3 PLACES = 0 2 PLACES = 0 CURRENT REV DESC: UPDATE TO NEW PINS GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 DOCUMENT STATUS 12 SCALE ANGULAR TOL = 0 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 1 PLACE 0 PLACES 5.0 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 EC NO: 600289 DRWN: SVANG01 CHK'D: RWHIPPLE APPR: CHIRSCHY INITIAL REVISION: DRWN: MSIBARRA APPR: SMILLER THIRD ANGLE PROJECTION 4 2018/06/01 2018/06/01 2018/06/01 STACKED SFP+ 2X8 ASS'Y WITH METAL EMI GASKET LIGHTPIPES-IMPROVED EMI PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2010/09/03 2011/08/04 DRAWING SERIES C-SIZE 76352 3 SD-76352-0002 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET 2 F SHEET NUMBER 1 OF 5 1 A 12 11 10 9 8 7 5 6 4 3 2 1 H H G G 114.50 0.20 SEE NOTE 7 76352-7001 WITH INNER AND OUTER LIGHT PIPE PORTS F F E E D D 76352-7002 WITH INNER LIGHT PIPE PORTS 114.85 REFERENCE C C B B SYMBOLS = 0 = 0 = 0 76352-7003 WITH OUTER LIGHT PIPE PORTS A P1 RELEASE DATE 11 2018/06/01 10 22:27:30 C 9 8 7 6 mm 2:1 = 0 4 PLACES = 0 3 PLACES = 0 2 PLACES = 0 CURRENT REV DESC: UPDATE TO NEW PINS GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 DOCUMENT STATUS 12 SCALE ANGULAR TOL = 0 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 1 PLACE 0 PLACES 5.0 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 EC NO: 600289 DRWN: SVANG01 CHK'D: RWHIPPLE APPR: CHIRSCHY INITIAL REVISION: DRWN: MSIBARRA APPR: SMILLER THIRD ANGLE PROJECTION 4 2018/06/01 2018/06/01 2018/06/01 STACKED SFP+ 2X8 ASS'Y WITH METAL EMI GASKET LIGHTPIPES-IMPROVED EMI PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2010/09/03 2011/08/04 DRAWING SERIES C-SIZE 76352 3 SD-76352-0002 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET 2 F SHEET NUMBER 2 OF 5 1 A 12 11 10 9 7 8 5 6 4 3 2 1 110.75 9.50 5.50 TYPICAL H 8.00 H SEE KEEPOUT ZONE DETIAL B SEE PIN-OUT DETAIL SEE DETAIL A 4.00 TYPICAL INNER LIGHTPIPE OUTLINE 7.50 G G OUTER LIGHTPIPE OUTLINE F 42.10 3.50 18 PLACES F 51.625 1.75 18 PLACES TRACE KEEPOUT AREAS 18 PLACES E E 4.00 18 PLACES 8.00 TYPICAL D 14.25 TYPICAL 7.125 REF EDGE OF BOARD 14.25 TYPICAL D 0.10 A B 7.125 REF 1.05 0.05 CAGE GROUND TAILS TYPICAL 0.13 2 PLACES 114.00 C RECOMMENDED PCB LAYOUT - COMPONENTS SIDE RECOMMENDED PCB THICKNESS - 2.63mm (.093 INCH) THE ENTIRE AREA OF THE CONNECTOR FOOTPRINT TO BE CONSIDERED THE KEEP OUT AREA FOR COMPONENTS (OTHER THAN LIGHT PIPE LED'S) THIS AREA IS INDICATED BY THE DASHED LINE T20 T18 T16 T14 T12 T17 T15 T13 T11 T19 T3 T1 T2 L10 B T5 T4 L8 L9 T7 L7 T9 T8 T10 T6 L2 L4 L6 L5 L3 B L1 SYMBOLS L11 L13 L15 L17 L19 = 0 = 0 L12 L14 L16 L18 L20 A = 0 CONNECTOR PIN-OUT COMPONENT SIDE OF BOARD DOCUMENT STATUS 12 P1 RELEASE DATE 11 2018/06/01 10 C 9 8 7 6 SCALE mm 3:1 = 0 4 PLACES = 0 3 PLACES = 0 2 PLACES = 0 CURRENT REV DESC: UPDATE TO NEW PINS GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 22:27:30 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS ANGULAR TOL = 0 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 C 1 PLACE 0 PLACES 5.0 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 EC NO: 600289 DRWN: SVANG01 CHK'D: RWHIPPLE APPR: CHIRSCHY INITIAL REVISION: DRWN: MSIBARRA APPR: SMILLER THIRD ANGLE PROJECTION 4 2018/06/01 2018/06/01 2018/06/01 STACKED SFP+ 2X8 ASS'Y WITH METAL EMI GASKET LIGHTPIPES-IMPROVED EMI PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2010/09/03 2011/08/04 DRAWING SERIES C-SIZE 76352 3 SD-76352-0002 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET 2 F SHEET NUMBER 3 OF 5 1 A 12 11 H 10 9 8 T20 T11 T1 T10 7 5 6 3 2 11.00 1.70 REFERENCE 7.60 7.20 OUTER LIGHTPIPE 0.10 A B 6.80 0.46 0.05 TYPICAL (0.57 DRILL) (0.88 PAD) 6.40 G 3.80 INNER LIGHTPIPE OUTER LIGHTPIPE L1 L11 L20 1.85 0.05 TYPICAL A 0.98 INNER LIGHTPIPE OUTLINE TYPICAL F F 6.52 DETAIL B SCALE 5:1 CIRCUIT NUMBERING AND LIGHTPIPE IDENTIFICATION E G 0.10 A B 1.60 TYPICAL L10 1 H 1.70 REFERENCE INNER LIGHTPIPE 4 0.65 5.14 2.20 3.59 E 2.28 4.41 3.95 3.67 0.73 0.70 1.50 1.25 0.25 A D 1.90 D 0.35 OUTER LIGHTPIPE OUTLINE TYPICAL 2.56 DETAIL A SCALE 8:1 3.57 4.90 7.11 C C 7.85 11.43 10.06 13.13 B B SYMBOLS = 0 0.62 2.00 0.62 REF = 0 = 0 DETAIL - LIGHT PIPE AND OTHER ZONES THE HATCHED AREA IN THIS VIEW INDICATES ZONES THAT ARE OCCUPED BY THE PLASTIC HOUSING THAT SEATS AGAINST THE PCB AND BY THE VERTICAL METAL CAGE WALL THAT STOPS JUST SHORT OF THE PCB A DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 P1 RELEASE DATE 11 2018/06/01 10 9 8 7 6 mm 1:1 = 0 4 PLACES = 0 3 PLACES = 0 2 PLACES = 0 CURRENT REV DESC: UPDATE TO NEW PINS GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 C SCALE ANGULAR TOL = 0 22:27:30 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 1 PLACE 0 PLACES 5.0 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 EC NO: 600289 DRWN: SVANG01 CHK'D: RWHIPPLE APPR: CHIRSCHY INITIAL REVISION: DRWN: MSIBARRA APPR: SMILLER THIRD ANGLE PROJECTION 4 2018/06/01 2018/06/01 2018/06/01 STACKED SFP+ 2X8 ASS'Y WITH METAL EMI GASKET LIGHTPIPES-IMPROVED EMI PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2010/09/03 2011/08/04 DRAWING SERIES C-SIZE 76352 3 SD-76352-0002 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET 2 F SHEET NUMBER 4 OF 5 1 A 12 11 10 9 8 7 5 6 4 H 3 2 1 H 115.30 0.10 Z G G 26.00 0.10 F F Z 117.02 MINIMUM BEZEL CUT-OUT DETAIL RECOMMENDED BEZEL THICKNESS: 0.8mm - 2.6mm E E BEZEL FRONT EDGE OF CONNECTOR D BEZEL CUTOUT 0.00 0.10 3.50 0.30 C 7.00 REFERENCE D 26.00 REFERENCE PCB C SECTION Z-Z B B SYMBOLS = 0 = 0 = 0 A P1 RELEASE DATE 11 2018/06/01 10 22:27:30 C 9 8 7 6 mm 1:1 = 0 4 PLACES = 0 3 PLACES = 0 2 PLACES = 0 CURRENT REV DESC: UPDATE TO NEW PINS GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 DOCUMENT STATUS 12 SCALE ANGULAR TOL = 0 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 1 PLACE 0 PLACES 5.0 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 EC NO: 600289 DRWN: SVANG01 CHK'D: RWHIPPLE APPR: CHIRSCHY INITIAL REVISION: DRWN: MSIBARRA APPR: SMILLER THIRD ANGLE PROJECTION 4 2018/06/01 2018/06/01 2018/06/01 STACKED SFP+ 2X8 ASS'Y WITH METAL EMI GASKET LIGHTPIPES-IMPROVED EMI PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2010/09/03 2011/08/04 DRAWING SERIES C-SIZE 76352 3 SD-76352-0002 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET 2 F SHEET NUMBER 5 OF 5 1 A