PRV6 www.vishay.com Vishay Sfernice Fully Sealed Potentiometer Cermet or Conductive Plastic FEATURES * * * * * * * * * PRV6S high power rating 1.5 W at 70 C (cermet) PRV6A 0.75 W at 70 C (conductive plastic) Tests according to CECC 41000 or IEC 60393-1 Military performances Low cost Fully sealed and panel sealed Compatible RV6 (MIL R 94) Mechanical endurance 50 000 cycles Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 DIMENSIONS in millimeters (inches) 0.5 mm ( 0.02") PRV6 STYLE A AND S PRV6 STYLE B AND C 9.5 (0.374) 12.1 (0.476) 5 (0.200) 2.5 (0.098) 0.8 (0.031) 0.8 (0.031) SHAFT DIAMETER 3 mm (0.118") BUSHING A-B-C SHAFT DIAMETER 3.17 mm (0.125") BUSHING A-B-C SHAFT DIAMETER 4 mm (0.157") BUSHING H-I (not panel sealed) AB BA BB BJ AJ O 4 (0.157) AA O 3.17 (0.125) O 3 (0.118) B = see bushing table 0.8 (0.031) EA EB EJ 5.08 (0.200) O 12.7 (0.50) 5.08 (0.200) 2.15 (0.085) 2.15 (0.085) O 12.7 (0.50) 1.6 x 0.3 (0.063 x 0.012) 5.08 (0.200) 0.8 x 0.3 (0.031 x 0.012) LEADS Y = SOLDER LUGS 5.08 (0.200) LEADS X = PCB PINS 0.8 (0.031) 0.5 (0.020) Revision: 04-May-12 1 2.4 (0.094) Document Number: 51035 For technical questions, contact: sfer@vishay.com - See also Application Notes: www.vishay.com/doc?51001 and www.vishay.com/doc?52029 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 PRV6 www.vishay.com Vishay Sfernice ELECTRICAL SPECIFICATIONS PRV6S, PRV6B Resistive element PRV6A, PRV6C cermet conductive plastic Electrical travel Resistance range 270 15 linear taper (A) 20 to 10 M 1 k to 1 M non-linear taper (F-L) 470 to 1 M 470 to 500 k ( 20 %) Vs % Ve 90 % F 50 % A Taper L 20 % 10 % 25 50 75 Electrical travel 270 15 15 Mechanical travel 300 Tolerance standard on request 20 % 20 % 10 %, 5 % 10 % (1 k to 100 k) c a (1) Circuit diagram (3) b (2) Power rating at 70 C linear 1.5 W at 70 C 0.75 W at 70 C 0.75 W 0.4 W other tapers PRV6S, PRV6B linear taper POWER IN WATT 1.50 Power rating chart cw PRV6S, PRV6B non-linear taper PRV6A, PRV6C linear taper 0.75 PRV6A, PRV6C non-linear taper 0.4 0 0 20 40 60 70 80 125 100 AMBIENT TEMPERATURE IN DEGREES CELSIUS Temperature coefficient (typical) 150 ppm/C Limiting element voltage 350 V 2 % or 3 Contact resistance variation (CRV) 1 End resistance (typical) Dielectric strength (RMS) 1750 VRMS 106 M Insulation resistance (500 VDC) Revision: 04-May-12 500 ppm/C 2 Document Number: 51035 For technical questions, contact: sfer@vishay.com - See also Application Notes: www.vishay.com/doc?51001 and www.vishay.com/doc?52029 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 PRV6 www.vishay.com Vishay Sfernice MECHANICAL SPECIFICATIONS Mechanical travel 300 5 Operating torque (Ncm (oz.in.)) 0.5 to 2 (0.7 to 3) End stop torque (max. Ncm (lb.in.)) 35 (3) Tightening torque (max. Ncm (lb.in.)) 150 (13) ENVIRONMENTAL SPECIFICATIONS Temperature range PRV6S, PRV6B PRV6A, PRV6C - 55 C to + 125 C - 40 C to + 125 C 55/125/56 40/125/56 Climatic category Sealing Fully sealed contailer; IP67 and panel sealed PERFORMANCES TESTS TYPICAL VALUES AND DRIFTS CONDITIONS RT/RT (%) R1-2/R1-2 (%) Electrical endurance 1000 h at rated power 90'/30' - temperature 70 C 1% Climatic sequence Phase A dry heat 100 C Phase B damp heat Phase C cold - 55 C Phase D damp heat 5 cycles 0.5 % 1% Damp heat, steady state 56 days 0.5 % 1% Change of temperature 5 cycles, - 55 C to + 125 C 0.5 % Mechanical endurance 50 000 cycles 3% 50 g at 11 ms 3 successive shocks in 3 directions 0.1 % 0.2 % 10 Hz to 55 Hz 0.75 mm or 10 g during 6 h 0.1 % 0.2 % Shock Vibration OTHER CRV < 3 % Rn Insulation resistance: > 104 M CRV < 2 % Rn STANDARD RESISTANCE ELEMENT DATA STANDARD RESISTANCE VALUES PRV6S AND PRV6B WITH LINEAR TAPER MAX. POWER AT 70 C MAX. WORKING VOLTAGE PRV6S AND PRV6B WITH NON-LINEAR TAPER MAX. WIPER CURRENT MAX. POWER AT 70 C MAX. WORKING VOLTAGE MAX. WIPER CURRENT W V mA W V mA 20 1.5 5.48 274 50 1.5 8.66 173 100 1.5 12.2 122 200 1.5 17.3 87 500 1.5 27.4 55 0.75 19.4 39 1K 1.5 38.7 38.7 0.75 27.3 27.4 2K 1.5 54.8 27.4 0.75 38.2 19.3 5K 1.5 86.6 17.3 0.75 61.2 12.2 10K 1.5 122.5 12.2 0.75 87 8.7 20K 1.5 173 8.26 0.75 122 6.1 50K 1.5 274 5.65 0.75 194 3.9 100K 1.22 350 3.5 0.75 273 2.74 220K 0.61 350 1.75 0.61 350 1.75 500K 0.25 350 0.70 0.25 350 0.7 1M 0.12 350 0.35 0.12 350 0.35 2M 0.06 350 0.17 5M 0.025 350 0.070 10M 0.012 350 0.035 Revision: 04-May-12 3 Document Number: 51035 For technical questions, contact: sfer@vishay.com - See also Application Notes: www.vishay.com/doc?51001 and www.vishay.com/doc?52029 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 PRV6 www.vishay.com Vishay Sfernice MARKING * * * * Vishay trademark Part number Manufacturing date code Terminal: 1 PACKAGING * Box of 15, 20, 25, or 50 pieces, code B12, B15, B17, or B25, depending of body and shaft construction OPTIONS SPECIAL FEATURES Panel sealing Except for dia. 4 mm shaft, an O.ring is supplied with the potentiometer. This O.ring should be placed into the groove of the body and ensures the panel sealing. For dia. 4 mm shaft please see note "P" in ordering information. Shaft locking Shafts Shaft lengths are measured from the mounting face to the free end of the shaft. Special shafts are available if the customer supplies a drawing. The shaft slot is aligned to the wiper within 10. Hardware Nuts, washer and O.ring are separately supplied (not mounted on the potentiometer), in a small bag placed in the packaging. Except for dia. 4 mm shaft, the potentiometers are delivered with 2 opposite locating pegs orientated at 45. These 2 pegs can be easily broken-off by the customer. On request, the orientation of the pegs can be at 30 instead of 45. Locating peg Revision: 04-May-12 4 Document Number: 51035 For technical questions, contact: sfer@vishay.com - See also Application Notes: www.vishay.com/doc?51001 and www.vishay.com/doc?52029 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 PRV6 www.vishay.com Vishay Sfernice LOCATING PEG CODE BUSHING OLD CODE A L A 6 x x R 0 x (1) B 61 x x x (1) C 62 x x x (1) D 61H x x x (1) E 62H x x H 6Q x x I 61Q J 6QP K 61QP S 61QH S 61QPH x (1) x x x x Note (1) Not standard, special manufacturing ORDERING INFORMATION (Part Number) P MODEL PRV6 R V 6 STYLE B B B G X LOCATING PEG BUSHING S = Standard A = Audio B = Body A length B C = Audio and body C length D A Old codes O L 1/4 1/4 6 1/4 3/8 61 1/4 1/2 62 1/4 3/8 61H E 1/4 1/2 H 7 6.5 0 = Without A = 45 L = 30 R = 180 round (see locating peg table above) B 1 SHAFT O L Old codes AA 3 9.5 K AB 3 12.5 M AJ 3 22 R BA 1/8 9.5 CK 62H BB 1/8 12.5 CM 6Q BG 1/8 16 CD I 7 9.5 61Q BJ 1/8 22 CR J 7 6.5 6QP EA 4 9.5 E K 7 9.5 61QP EB 4 12.5 F S 7 9.5 61QH EJ 4 22 G S 7 9.5 61QPH AP 7 5 0 2 LEADS PACKAGING X= PCB pins (old code W) Y= Solder lugs Depending of body and shaft construction: B12 = Box 15 pcs B15 = Box 20 pcs B17 = Box 25 pcs B25 = Box 50 pcs M A RESISTANCE CODE/ TOLERANCE/ TAPER OR SPECIAL Resistance: From 200 = 20 to 106 = 10 M for linear cermet Tolerance: standard M = 20 % on request K = 10 % or J=5% Taper: A, L, F or special code given by Vishay custom shaft all are slotted PART NUMBER DESCRIPTION (for information only using old codes) PRV S 61 MODEL BUSHING LEADS Revision: 04-May-12 W CD 5K 20 % A BO e3 SPECIAL SHAFT VALUE TOLERANCE TAPER SPECIAL PACKAGING SPECIAL AP No SPECIAL 5 LEAD FINISH Document Number: 51035 For technical questions, contact: sfer@vishay.com - See also Application Notes: www.vishay.com/doc?51001 and www.vishay.com/doc?52029 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000